From: Hauke Mehrtens Date: Sun, 25 Nov 2018 18:35:16 +0000 (+0100) Subject: lantiq: copy target to kernel 4.19 X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=eee1b34ce688efcb824ea9ce08edfce7ec507599;p=openwrt%2Fstaging%2Fdangole.git lantiq: copy target to kernel 4.19 This just copies the files from the kernel 4.14 specific folders into the kernel 4.19 specific folder, no changes are done to the files in this commit. Signed-off-by: Hauke Mehrtens --- diff --git a/target/linux/lantiq/ase/config-4.19 b/target/linux/lantiq/ase/config-4.19 new file mode 100644 index 0000000000..cf27a148b7 --- /dev/null +++ b/target/linux/lantiq/ase/config-4.19 @@ -0,0 +1,26 @@ +CONFIG_ADM6996_PHY=y +CONFIG_CPU_MIPS32_R1=y +# CONFIG_CPU_MIPS32_R2 is not set +CONFIG_CPU_MIPSR1=y +CONFIG_CRC16=y +CONFIG_CRYPTO_ACOMP2=y +CONFIG_CRYPTO_DEFLATE=y +CONFIG_FIRMWARE_IN_KERNEL=y +CONFIG_FIRMWARE_MEMMAP=y +CONFIG_GPIO_GENERIC=y +CONFIG_GPIO_GENERIC_PLATFORM=y +# CONFIG_ISDN is not set +# CONFIG_LBDAF is not set +CONFIG_LEDS_TRIGGER_HEARTBEAT=y +CONFIG_MIPS_FPU_EMULATOR=y +CONFIG_NLS=y +# CONFIG_PSB6970_PHY is not set +# CONFIG_RTL8366_SMI is not set +CONFIG_SOC_AMAZON_SE=y +# CONFIG_SOC_XWAY is not set +CONFIG_USB=y +CONFIG_USB_COMMON=y +# CONFIG_USB_EHCI_HCD is not set +CONFIG_USB_SUPPORT=y +CONFIG_ZLIB_DEFLATE=y +CONFIG_ZLIB_INFLATE=y diff --git a/target/linux/lantiq/config-4.19 b/target/linux/lantiq/config-4.19 new file mode 100644 index 0000000000..7233a88aa6 --- /dev/null +++ b/target/linux/lantiq/config-4.19 @@ -0,0 +1,227 @@ +CONFIG_ARCH_BINFMT_ELF_STATE=y +CONFIG_ARCH_CLOCKSOURCE_DATA=y +CONFIG_ARCH_DISCARD_MEMBLOCK=y +CONFIG_ARCH_HAS_ELF_RANDOMIZE=y +# CONFIG_ARCH_HAS_GCOV_PROFILE_ALL is not set +CONFIG_ARCH_HAS_RESET_CONTROLLER=y +# CONFIG_ARCH_HAS_SG_CHAIN is not set +# CONFIG_ARCH_HAS_STRICT_KERNEL_RWX is not set +# CONFIG_ARCH_HAS_STRICT_MODULE_RWX is not set +CONFIG_ARCH_HIBERNATION_POSSIBLE=y +CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y +CONFIG_ARCH_MIGHT_HAVE_PC_SERIO=y +CONFIG_ARCH_MMAP_RND_BITS_MAX=15 +CONFIG_ARCH_MMAP_RND_COMPAT_BITS_MAX=15 +# CONFIG_ARCH_OPTIONAL_KERNEL_RWX is not set +# CONFIG_ARCH_OPTIONAL_KERNEL_RWX_DEFAULT is not set +CONFIG_ARCH_SUPPORTS_UPROBES=y +CONFIG_ARCH_SUSPEND_POSSIBLE=y +CONFIG_ARCH_USE_BUILTIN_BSWAP=y +CONFIG_ARCH_USE_QUEUED_RWLOCKS=y +CONFIG_ARCH_USE_QUEUED_SPINLOCKS=y +CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y +CONFIG_CEVT_R4K=y +CONFIG_CLKDEV_LOOKUP=y +CONFIG_CLONE_BACKWARDS=y +CONFIG_CPU_BIG_ENDIAN=y +CONFIG_CPU_GENERIC_DUMP_TLB=y +CONFIG_CPU_HAS_PREFETCH=y +CONFIG_CPU_HAS_RIXI=y +CONFIG_CPU_HAS_SYNC=y +CONFIG_CPU_MIPS32=y +# CONFIG_CPU_MIPS32_R1 is not set +CONFIG_CPU_MIPS32_R2=y +CONFIG_CPU_MIPSR2=y +CONFIG_CPU_NEEDS_NO_SMARTMIPS_OR_MICROMIPS=y +CONFIG_CPU_R4K_CACHE_TLB=y +CONFIG_CPU_R4K_FPU=y +CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y +CONFIG_CPU_SUPPORTS_HIGHMEM=y +CONFIG_CPU_SUPPORTS_MSA=y +CONFIG_CRYPTO_HASH=y +CONFIG_CRYPTO_HASH2=y +CONFIG_CRYPTO_RNG2=y +CONFIG_CRYPTO_WORKQUEUE=y +CONFIG_CSRC_R4K=y +CONFIG_DMA_NONCOHERENT=y +CONFIG_DTC=y +# CONFIG_DT_EASY50712 is not set +CONFIG_EARLY_PRINTK=y +CONFIG_ETHERNET_PACKET_MANGLE=y +CONFIG_FIXED_PHY=y +CONFIG_GENERIC_ATOMIC64=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_CMOS_UPDATE=y +CONFIG_GENERIC_CPU_AUTOPROBE=y +CONFIG_GENERIC_IO=y +CONFIG_GENERIC_IRQ_CHIP=y +CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=y +CONFIG_GENERIC_IRQ_IPI=y +CONFIG_GENERIC_IRQ_SHOW=y +CONFIG_GENERIC_PCI_IOMAP=y +CONFIG_GENERIC_PHY=y +CONFIG_GENERIC_SCHED_CLOCK=y +CONFIG_GENERIC_SMP_IDLE_THREAD=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GPIOLIB=y +CONFIG_GPIO_MM_LANTIQ=y +CONFIG_GPIO_STP_XWAY=y +CONFIG_GPIO_SYSFS=y +# CONFIG_GRO_CELLS is not set +CONFIG_HANDLE_DOMAIN_IRQ=y +CONFIG_HARDWARE_WATCHPOINTS=y +CONFIG_HAS_DMA=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT_MAP=y +# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set +# CONFIG_HAVE_ARCH_BITREVERSE is not set +CONFIG_HAVE_ARCH_COMPILER_H=y +CONFIG_HAVE_ARCH_JUMP_LABEL=y +CONFIG_HAVE_ARCH_KGDB=y +CONFIG_HAVE_ARCH_SECCOMP_FILTER=y +CONFIG_HAVE_ARCH_TRACEHOOK=y +# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set +CONFIG_HAVE_CBPF_JIT=y +CONFIG_HAVE_CC_STACKPROTECTOR=y +CONFIG_HAVE_CLK=y +CONFIG_HAVE_CONTEXT_TRACKING=y +CONFIG_HAVE_COPY_THREAD_TLS=y +CONFIG_HAVE_C_RECORDMCOUNT=y +CONFIG_HAVE_DEBUG_KMEMLEAK=y +CONFIG_HAVE_DEBUG_STACKOVERFLOW=y +CONFIG_HAVE_DMA_API_DEBUG=y +CONFIG_HAVE_DMA_CONTIGUOUS=y +CONFIG_HAVE_DYNAMIC_FTRACE=y +CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y +CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y +CONFIG_HAVE_FUNCTION_TRACER=y +CONFIG_HAVE_GENERIC_DMA_COHERENT=y +CONFIG_HAVE_IDE=y +CONFIG_HAVE_IRQ_EXIT_ON_IRQ_STACK=y +CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y +CONFIG_HAVE_KVM=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_HAVE_MEMBLOCK=y +CONFIG_HAVE_MEMBLOCK_NODE_MAP=y +CONFIG_HAVE_MOD_ARCH_SPECIFIC=y +CONFIG_HAVE_NET_DSA=y +CONFIG_HAVE_OPROFILE=y +CONFIG_HAVE_PERF_EVENTS=y +CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y +CONFIG_HAVE_SYSCALL_TRACEPOINTS=y +CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y +CONFIG_HW_HAS_PCI=y +CONFIG_HW_RANDOM=y +CONFIG_HZ=250 +# CONFIG_HZ_100 is not set +CONFIG_HZ_250=y +CONFIG_HZ_PERIODIC=y +CONFIG_INITRAMFS_SOURCE="" +CONFIG_IRQCHIP=y +CONFIG_IRQ_DOMAIN=y +CONFIG_IRQ_DOMAIN_HIERARCHY=y +CONFIG_IRQ_FORCED_THREADING=y +CONFIG_IRQ_MIPS_CPU=y +CONFIG_IRQ_WORK=y +CONFIG_LANTIQ=y +CONFIG_LANTIQ_DT_NONE=y +CONFIG_LANTIQ_ETOP=y +CONFIG_LANTIQ_WDT=y +# CONFIG_LANTIQ_XRX200 is not set +CONFIG_LEDS_GPIO=y +CONFIG_LIBFDT=y +CONFIG_MDIO_BUS=y +CONFIG_MDIO_DEVICE=y +CONFIG_MFD_CORE=y +CONFIG_MFD_SYSCON=y +CONFIG_MIGRATION=y +CONFIG_MIPS=y +CONFIG_MIPS_ASID_BITS=8 +CONFIG_MIPS_ASID_SHIFT=0 +CONFIG_MIPS_CLOCK_VSYSCALL=y +# CONFIG_MIPS_CMDLINE_DTB_EXTEND is not set +# CONFIG_MIPS_CMDLINE_FROM_BOOTLOADER is not set +CONFIG_MIPS_CMDLINE_FROM_DTB=y +# CONFIG_MIPS_ELF_APPENDED_DTB is not set +# CONFIG_MIPS_HUGE_TLB_SUPPORT is not set +CONFIG_MIPS_L1_CACHE_SHIFT=5 +# CONFIG_MIPS_MACHINE is not set +# CONFIG_MIPS_MT_SMP is not set +# CONFIG_MIPS_NO_APPENDED_DTB is not set +CONFIG_MIPS_RAW_APPENDED_DTB=y +CONFIG_MIPS_SPRAM=y +# CONFIG_MIPS_VPE_LOADER is not set +CONFIG_MODULES_USE_ELF_REL=y +CONFIG_MTD_CFI_ADV_OPTIONS=y +CONFIG_MTD_CFI_GEOMETRY=y +CONFIG_MTD_CMDLINE_PARTS=y +CONFIG_MTD_JEDECPROBE=y +CONFIG_MTD_LANTIQ=y +CONFIG_MTD_M25P80=y +CONFIG_MTD_SPI_NOR=y +CONFIG_MTD_SPLIT_BRNIMAGE_FW=y +CONFIG_MTD_SPLIT_EVA_FW=y +CONFIG_MTD_SPLIT_FIRMWARE=y +CONFIG_MTD_SPLIT_TPLINK_FW=y +CONFIG_MTD_SPLIT_UIMAGE_FW=y +CONFIG_NEED_DMA_MAP_STATE=y +CONFIG_NEED_PER_CPU_KM=y +CONFIG_NO_GENERIC_PCI_IOPORT_MAP=y +# CONFIG_NO_IOPORT_MAP is not set +CONFIG_OF=y +CONFIG_OF_ADDRESS=y +CONFIG_OF_EARLY_FLATTREE=y +CONFIG_OF_FLATTREE=y +CONFIG_OF_GPIO=y +CONFIG_OF_IRQ=y +CONFIG_OF_MDIO=y +CONFIG_OF_NET=y +CONFIG_PCI_DRIVERS_LEGACY=y +CONFIG_PERF_USE_VMALLOC=y +CONFIG_PGTABLE_LEVELS=2 +CONFIG_PHYLIB=y +CONFIG_PHY_LANTIQ_RCU_USB2=y +CONFIG_PINCTRL=y +CONFIG_PINCTRL_LANTIQ=y +# CONFIG_PINCTRL_SINGLE is not set +CONFIG_PINCTRL_XWAY=y +CONFIG_POWER_RESET=y +CONFIG_POWER_RESET_SYSCON=y +CONFIG_PSB6970_PHY=y +# CONFIG_RCU_NEED_SEGCBLIST is not set +# CONFIG_RCU_STALL_COMMON is not set +CONFIG_REGMAP=y +CONFIG_REGMAP_MMIO=y +CONFIG_RESET_CONTROLLER=y +CONFIG_RESET_LANTIQ=y +CONFIG_RTL8366RB_PHY=y +CONFIG_RTL8366_SMI=y +# CONFIG_SCHED_INFO is not set +# CONFIG_SCSI_DMA is not set +# CONFIG_SENSORS_LTQ_CPUTEMP is not set +# CONFIG_SERIAL_8250 is not set +CONFIG_SERIAL_LANTIQ=y +# CONFIG_SOC_AMAZON_SE is not set +# CONFIG_SOC_FALCON is not set +CONFIG_SOC_TYPE_XWAY=y +CONFIG_SOC_XWAY=y +CONFIG_SPI=y +CONFIG_SPI_LANTIQ_SSC=y +CONFIG_SPI_MASTER=y +CONFIG_SRCU=y +CONFIG_SWAP_IO_SPACE=y +CONFIG_SWCONFIG=y +CONFIG_SWPHY=y +CONFIG_SYSCTL_EXCEPTION_TRACE=y +CONFIG_SYS_HAS_CPU_MIPS32_R1=y +CONFIG_SYS_HAS_CPU_MIPS32_R2=y +CONFIG_SYS_HAS_EARLY_PRINTK=y +CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y +CONFIG_SYS_SUPPORTS_ARBIT_HZ=y +CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y +CONFIG_SYS_SUPPORTS_MIPS16=y +CONFIG_SYS_SUPPORTS_MULTITHREADING=y +CONFIG_TICK_CPU_ACCOUNTING=y +CONFIG_TINY_SRCU=y +CONFIG_USE_OF=y +# CONFIG_XRX200_PHY_FW is not set diff --git a/target/linux/lantiq/falcon/config-4.19 b/target/linux/lantiq/falcon/config-4.19 new file mode 100644 index 0000000000..84b36d0066 --- /dev/null +++ b/target/linux/lantiq/falcon/config-4.19 @@ -0,0 +1,12 @@ +# CONFIG_MFD_CORE is not set +CONFIG_MTD_NAND=y +CONFIG_MTD_NAND_ECC=y +CONFIG_MTD_SPLIT_FIRMWARE_NAME="linux" +CONFIG_PINCTRL_FALCON=y +# CONFIG_PSB6970_PHY is not set +# CONFIG_RESET_LANTIQ is not set +# CONFIG_RTL8366_SMI is not set +CONFIG_SOC_FALCON=y +# CONFIG_SOC_TYPE_XWAY is not set +# CONFIG_SOC_XWAY is not set +CONFIG_SPI_FALCON=y diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ACMP252.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ACMP252.dts deleted file mode 100644 index 5a2d867196..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ACMP252.dts +++ /dev/null @@ -1,114 +0,0 @@ -/dts-v1/; - -#include "danube.dtsi" - -/ { - compatible = "audiocodes,mp-252", "lantiq,xway", "lantiq,danube"; - model = "AudioCodes MediaPack MP-252"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - memory@0 { - reg = <0x0 0x4000000>; - }; - - usb_vbus: regulator-usb-vbus { - compatible = "regulator-fixed"; - - regulator-name = "USB_VBUS"; - - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - gpio = <&gpio 3 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - exin { - lantiq,groups = "exin1"; - lantiq,function = "exin"; - }; - pci { - lantiq,groups = "gnt1", "req1"; - lantiq,function = "pci"; - }; - }; -}; - -&gsw { - phy-mode = "rmii"; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x2000000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x0 0x20000>; - read-only; - }; - - partition@20000 { - label = "uboot_env"; - reg = <0x20000 0x20000>; - }; - - partition@40000 { - label = "boardconfig"; - reg = <0x40000 0x60000>; - read-only; - }; - - partition@a0000 { - label = "firmware"; - reg = <0xa0000 0xf20000>; - }; - - partition@fc0000 { - label = "sysconfig"; - reg = <0xfc0000 0x40000>; - }; - - partition@0x1000000 { - label = "rootfs_data"; - reg = <0x1000000 0x1000000>; - }; - }; - }; -}; - -&pci0 { - status = "okay"; -}; - -&usb_phy { - status = "okay"; -}; - -&usb { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; - -&vmmc { - status = "okay"; - gpios = <&gpio 31 GPIO_ACTIVE_HIGH>; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ALL0333CJ.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ALL0333CJ.dts deleted file mode 100644 index df62ac2d92..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ALL0333CJ.dts +++ /dev/null @@ -1,116 +0,0 @@ -/dts-v1/; - -#include "amazonse.dtsi" - -/ { - compatible = "allnet,all0333cj", "lantiq,xway", "lantiq,ase"; - model = "Allnet ALL0333CJ DSL Modem"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - - aliases { - led-boot = &power; - led-failsafe = &power; - led-running = &power; - led-upgrade = &power; - - led-dsl = &dsl; - led-internet = &online_green; - }; - }; - - memory@0 { - reg = <0x0 0x1000000>; - }; - - gpio-leds { - compatible = "gpio-leds"; - - /* power led: red=off, green=on */ - power: power { - label = "all0333cj:green:power"; - gpios = <&gpio 13 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - - lan: lan { - label = "all0333cj:green:lan"; - gpios = <&gpio 3 GPIO_ACTIVE_LOW>; - }; - - dsl: dsl { - label = "all0333cj:green:dsl"; - gpios = <&gpio 1 GPIO_ACTIVE_LOW>; - }; - - online_green: online { - label = "all0333cj:green:online"; - gpios = <&gpio 12 GPIO_ACTIVE_LOW>; - }; - online_red { - label = "all0333cj:red:online"; - gpios = <&gpio 4 GPIO_ACTIVE_LOW>; - }; - }; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - asc { - lantiq,groups = "asc"; - lantiq,function = "asc"; - }; - keys_in { - lantiq,pins = "io0",/* "io25", */"io29"; - lantiq,pull = <2>; - lantiq,open-drain = <1>; - }; - }; -}; - -&gsw { - phy-mode = "mii"; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x400000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x00000 0x10000>; - read-only; - }; - - partition@10000 { - label = "firmware"; - reg = <0x10000 0x3ef200>; - }; - - partition@3ff200 { - label = "uboot_env"; - reg = <0x3ff200 0xc00>; - read-only; - }; - - partition@3ffe00 { - label = "dummy_bits"; - reg = <0x3ffe00 0x200>; - read-only; - }; - }; - }; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV4510PW.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV4510PW.dts deleted file mode 100644 index 6598a60f58..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV4510PW.dts +++ /dev/null @@ -1,230 +0,0 @@ -/dts-v1/; - -#include "danube.dtsi" - -#include - -/ { - compatible = "arcadyan,arv4510pw", "lantiq,xway", "lantiq,danube"; - model = "Wippies, Elisa"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power; - led-failsafe = &power2; - led-running = &power; - led-upgrade = &power; - - led-dsl = &adsl; - led-internet = &internet; - led-usb = &led_usb; - led-usb2 = &led_usb2; - led-wifi = &wifi; - }; - - memory@0 { - reg = <0x0 0x2000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - wps { - label = "wps"; - gpios = <&gpio 14 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - reset { - label = "reset"; - gpios = <&gpio 3 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - power: power { - label = "power"; - gpios = <&gpios 21 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - power2: power2 { - label = "power2"; - gpios = <&gpios 20 GPIO_ACTIVE_HIGH>; - }; - lan1 { - label = "lan1"; - gpios = <&gpios 19 GPIO_ACTIVE_HIGH>; - }; - lan2 { - label = "lan2"; - gpios = <&gpios 18 GPIO_ACTIVE_HIGH>; - }; - lan3 { - label = "lan3"; - gpios = <&gpios 17 GPIO_ACTIVE_HIGH>; - }; - lan4 { - label = "lan4"; - gpios = <&gpios 16 GPIO_ACTIVE_HIGH>; - }; - wifi: wifi { - label = "wifi"; - gpios = <&gpios 15 GPIO_ACTIVE_HIGH>; - }; - adsl: adsl { - label = "adsl"; - gpios = <&gpios 14 GPIO_ACTIVE_HIGH>; - }; - internet: internet { - label = "internet"; - gpios = <&gpios 13 GPIO_ACTIVE_HIGH>; - }; - internet2 { - label = "internet2"; - gpios = <&gpios 12 GPIO_ACTIVE_HIGH>; - }; - voip { - label = "voip"; - gpios = <&gpios 11 GPIO_ACTIVE_HIGH>; - }; - phone { - label = "phone"; - gpios = <&gpios 10 GPIO_ACTIVE_HIGH>; - }; - phone2 { - label = "phone2"; - gpios = <&gpios 9 GPIO_ACTIVE_HIGH>; - }; - led_usb: usb { - label = "usb"; - gpios = <&gpios 8 GPIO_ACTIVE_HIGH>; - }; - led_usb2: usb2 { - label = "usb2"; - gpios = <&gpios 7 GPIO_ACTIVE_HIGH>; - }; - usb3 { - label = "usb3"; - gpios = <&gpios 6 GPIO_ACTIVE_HIGH>; - }; - unlabeled { - label = "unlabeled"; - gpios = <&gpios 5 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - ebu { - lantiq,groups = "ebu a23"; - lantiq,function = "ebu"; - lantiq,open-drain = <0>; - lantiq,output = <1>; - }; - stp { - lantiq,groups = "stp"; - lantiq,function = "stp"; - lantiq,open-drain = <0>; - lantiq,output = <1>; - }; - exin { - lantiq,groups = "exin1", "exin2"; - lantiq,function = "exin"; - lantiq,output = <0>; - }; - pci_in { - lantiq,groups = "req1", "req2"; - lantiq,function = "pci"; - lantiq,output = <0>; - }; - pci_out { - lantiq,groups = "gnt1", "gnt2"; - lantiq,function = "pci"; - lantiq,open-drain = <0>; - lantiq,pull = <0>; - lantiq,output = <1>; - }; - pci_rst { - lantiq,pins = "io21"; - lantiq,open-drain = <0>; - lantiq,output = <1>; - }; - buttons { - lantiq,pins = "io3", "io14"; - lantiq,pull = <2>; - lantiq,output = <0>; - }; - }; -}; - -&gpios { - status = "okay"; - lantiq,groups = <0x7>; -}; - -&gsw { - phy-mode = "rmii"; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x1000000>; - #address-cells = <1>; - #size-cells = <1>; - - lantiq,noxip; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x00000 0x40000>; - read-only; - }; - - partition@40000 { - label = "uboot_env"; - reg = <0x40000 0x20000>; - read-only; - }; - - partition@60000 { - label = "firmware"; - reg = <0x60000 0xfa0000>; - }; - }; - }; -}; - -&pci0 { - status = "okay"; - lantiq,external-clock; - interrupt-map = < - 0x6000 0 0 1 &icu0 135 - 0x7800 0 0 1 &icu0 66 - 0x7800 0 0 2 &icu0 66 - 0x7800 0 0 3 &icu0 66 - >; - gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; - req-mask = <0x7>; -}; - -&vmmc { - status = "okay"; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV4518PWR01.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV4518PWR01.dts deleted file mode 100644 index 34f868f484..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV4518PWR01.dts +++ /dev/null @@ -1,8 +0,0 @@ -/dts-v1/; - -#include "ARV4518PWR01.dtsi" - -/ { - compatible = "arcadyan,arv4518pwr01", "lantiq,xway", "lantiq,danube"; - model = "SMC7908A-ISP"; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV4518PWR01.dtsi b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV4518PWR01.dtsi deleted file mode 100644 index f29c416c06..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV4518PWR01.dtsi +++ /dev/null @@ -1,206 +0,0 @@ -#include "danube.dtsi" - -#include - -/ { - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power; - led-failsafe = &power; - led-running = &power; - led-upgrade = &power; - - led-dsl = &dsl; - led-internet = &online; - led-usb = &led_usb; - led-wifi = &wifi; - }; - - memory@0 { - reg = <0x0 0x4000000>; - }; - - ath5k_eep { - compatible = "ath5k,eeprom"; - ath,eep-flash = <&boardconfig 0x400>; - ath,mac-offset = <0x16>; - ath,mac-increment = <1>; - ath,eep-swap; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - rfkill { - label = "rfkill"; - gpios = <&gpio 28 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - reset { - label = "reset"; - gpios = <&gpio 30 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - power: power { - label = "power"; - gpios = <&gpio 3 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - dsl: dsl { - label = "dsl"; - gpios = <&gpio 4 GPIO_ACTIVE_LOW>; - }; - online: online { - label = "online"; - gpios = <&gpio 5 GPIO_ACTIVE_LOW>; - }; - wifi: wifi { - label = "wifi"; - gpios = <&gpio 6 GPIO_ACTIVE_LOW>; - }; - wps { - label = "wps"; - gpios = <&gpio 7 GPIO_ACTIVE_LOW>; - }; - dsl2 { - label = "dsl2"; - gpios = <&gpio 8 GPIO_ACTIVE_LOW>; - }; - led_usb: usb { - label = "usb"; - gpios = <&gpio 19 GPIO_ACTIVE_LOW>; - }; - voice { - label = "voice"; - gpios = <&gpiomm 0 GPIO_ACTIVE_LOW>; - }; - fxs1 { - label = "fxs1"; - gpios = <&gpiomm 1 GPIO_ACTIVE_LOW>; - }; - fxs2 { - label = "fxs2"; - gpios = <&gpiomm 2 GPIO_ACTIVE_LOW>; - }; - fxo { - label = "fxo"; - gpios = <&gpiomm 3 GPIO_ACTIVE_LOW>; - }; - }; - - usb_vbus: regulator-usb-vbus { - compatible = "regulator-fixed"; - - regulator-name = "USB_VBUS"; - - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - gpio = <&gpio 14 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - ebu { - lantiq,groups = "ebu cs1"; - lantiq,function = "ebu"; - }; - pci_in { - lantiq,groups = "req1", "req2"; - lantiq,function = "pci"; - lantiq,open-drain = <1>; - lantiq,pull = <2>; - lantiq,output = <0>; - }; - pci_out { - lantiq,groups = "gnt1", "gnt2"; - lantiq,function = "pci"; - lantiq,pull = <0>; - lantiq,output = <1>; - }; - }; -}; - -&gpiomm { - status = "okay"; - lantiq,shadow = <0x0>; -}; - -&gsw { - phy-mode = "mii"; - mtd-mac-address = <&boardconfig 0x16>; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x2000000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x00000 0x10000>; /* 64 KB */ - read-only; - }; - - partition@10000 { - label = "uboot_env"; - reg = <0x10000 0x10000>; /* 64 KB */ - read-only; - }; - - partition@20000 { - label = "firmware"; - reg = <0x20000 0x3d0000>; - }; - - boardconfig: partition@400000 { - label = "boardconfig"; - reg = <0x3f0000 0x10000>; - read-only; - }; - }; - }; -}; - -&pci0 { - status = "okay"; - gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; - req-mask = <0xf>; -}; - -&usb_phy { - status = "okay"; -}; - -&usb { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; - -&vmmc { - status = "okay"; - gpios = <&gpio 31 GPIO_ACTIVE_HIGH>; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV4518PWR01A.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV4518PWR01A.dts deleted file mode 100644 index 9617398bbc..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV4518PWR01A.dts +++ /dev/null @@ -1,12 +0,0 @@ -/dts-v1/; - -#include "ARV4518PWR01.dtsi" - -/ { - compatible = "arcadyan,arv4518pwr01a", "lantiq,xway", "lantiq,danube"; - model = "SMC7908A-ISP, Airties WAV-221"; -}; - -&pci0 { - lantiq,external-clock; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV4519PW.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV4519PW.dts deleted file mode 100644 index e307b381a9..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV4519PW.dts +++ /dev/null @@ -1,203 +0,0 @@ -/dts-v1/; - -#include "danube.dtsi" - -#include - -/ { - compatible = "arcadyan,arv4519pw", "lantiq,xway", "lantiq,danube"; - model = "Vodafone Netfaster IAD 2, Pirelli P.RG A4201G"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power_green; - led-failsafe = &power_red; - led-running = &power_green; - led-upgrade = &power_green; - - led-dsl = &dsl; - led-internet = &internet_green; - led-usb = &led_usb; - led-wifi = &wifi; - }; - - memory@0 { - reg = <0x0 0x2000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - rfkill { - label = "rfkill"; - gpios = <&gpio 28 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - reset { - label = "reset"; - gpios = <&gpio 30 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - - power_green: power { - label = "arv4519pw:green:power"; - gpios = <&gpio 2 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - power_red: power2 { - label = "arv4519pw:red:power"; - gpios = <&gpio 7 GPIO_ACTIVE_LOW>; - }; - wifi: wifi { - label = "arv4519pw:green:wlan"; - gpios = <&gpio 6 GPIO_ACTIVE_LOW>; - }; - dsl: dsl { - label = "arv4519pw:green:dsl"; - gpios = <&gpio 4 GPIO_ACTIVE_LOW>; - }; - internet_green: online { - label = "arv4519pw:green:internet"; - gpios = <&gpio 5 GPIO_ACTIVE_LOW>; - }; - online2 { - label = "arv4519pw:red:internet"; - gpios = <&gpio 8 GPIO_ACTIVE_LOW>; - }; - led_usb: usb { - label = "arv4519pw:green:usb"; - gpios = <&gpio 19 GPIO_ACTIVE_LOW>; - }; - voip { - label = "arv4519pw:green:voip"; - gpios = <&gpiomm 0 GPIO_ACTIVE_LOW>; - }; - fxs1 { - label = "arv4519pw:green:phone1"; - gpios = <&gpiomm 1 GPIO_ACTIVE_LOW>; - }; - fxs2 { - label = "arv4519pw:green:phone2"; - gpios = <&gpiomm 2 GPIO_ACTIVE_LOW>; - }; - fxo { - label = "arv4519pw:green:line"; - gpios = <&gpiomm 3 GPIO_ACTIVE_LOW>; - }; - wps2 { - label = "arv4519pw:green:wps"; - gpios = <&gpiomm 4 GPIO_ACTIVE_LOW>; - }; - wps { - label = "arv4519pw:orange:wps"; - gpios = <&gpiomm 5 GPIO_ACTIVE_LOW>; - }; - wps3 { - label = "arv4519pw:red:wps"; - gpios = <&gpiomm 6 GPIO_ACTIVE_LOW>; - }; - }; - - usb_vbus: regulator-usb-vbus { - compatible = "regulator-fixed"; - - regulator-name = "USB_VBUS"; - - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - gpio = <&gpio 14 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - ebu { - lantiq,groups = "ebu cs1"; - lantiq,function = "ebu"; - }; - }; -}; - -&gpiomm { - status = "okay"; - lantiq,shadow = <0x400>; -}; - -&gsw { - phy-mode = "mii"; - mtd-mac-address = <&boardconfig 0x16>; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x2000000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x00000 0x10000>; - read-only; - }; - - partition@10000 { - label = "uboot_env"; - reg = <0x10000 0x10000>; - }; - - partition@20000 { - label = "firmware"; - reg = <0x20000 0x3d0000>; - }; - - boardconfig: partition@3f0000 { - label = "boardconfig"; - reg = <0x3f0000 0x10000>; - read-only; - }; - }; - }; -}; - -&pci0 { - status = "okay"; - lantiq,external-clock; - gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; - req-mask = <0xf>; -}; - -&usb_phy { - status = "okay"; -}; - -&usb { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; - -&vmmc { - status = "okay"; - gpios = <&gpio 31 GPIO_ACTIVE_HIGH>; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV4520PW.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV4520PW.dts deleted file mode 100644 index cd76bf5799..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV4520PW.dts +++ /dev/null @@ -1,228 +0,0 @@ -/dts-v1/; - -#include "danube.dtsi" - -#include - -/ { - compatible = "arcadyan,arv4520pw", "lantiq,xway", "lantiq,danube"; - model = "Easybox 800, WAV-281"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power_blue; - led-failsafe = &power_red; - led-running = &power_blue; - led-upgrade = &power_blue; - - led-dsl = &dsl; - led-internet = &internet_blue; - led-usb = &led_usb; - led-wifi = &wifi; - }; - - memory@0 { - reg = <0x0 0x2000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - rfkill { - label = "wps"; - gpios = <&gpio 29 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - reset { - label = "reset"; - gpios = <&gpio 30 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - - power_blue: power { - label = "arv4520pw:blue:power"; - gpios = <&gpio 3 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - dsl: dsl { - label = "arv4520pw:blue:dsl"; - gpios = <&gpio 4 GPIO_ACTIVE_LOW>; - }; - internet_blue: internet { - label = "arv4520pw:blue:internet"; - gpios = <&gpio 5 GPIO_ACTIVE_LOW>; - }; - power_red: power2 { - label = "arv4520pw:red:power"; - gpios = <&gpio 6 GPIO_ACTIVE_LOW>; - }; - wps { - label = "arv4520pw:yellow:wps"; - gpios = <&gpio 7 GPIO_ACTIVE_LOW>; - }; - wps2 { - label = "arv4520pw:red:wps"; - gpios = <&gpio 9 GPIO_ACTIVE_LOW>; - }; - /* - wps green is missing - */ - fxs1 { - label = "arv4520pw:blue:telefon1"; - gpios = <&gpiomm 0 GPIO_ACTIVE_LOW>; - }; - fxs2 { - label = "arv4520pw:blue:telefon2"; - gpios = <&gpiomm 1 GPIO_ACTIVE_LOW>; - }; - isdn { - label = "arv4520pw:blue:isdn"; - gpios = <&gpiomm 2 GPIO_ACTIVE_LOW>; - }; - fxo { - label = "arv4520pw:blue:line"; - gpios = <&gpiomm 3 GPIO_ACTIVE_LOW>; - }; - voice { - label = "arv4520pw:blue:sprache"; - gpios = <&gpiomm 4 GPIO_ACTIVE_LOW>; - }; - led_usb: usb { - label = "arv4520pw:blue:usb"; - gpios = <&gpiomm 5 GPIO_ACTIVE_LOW>; - }; - wifi: wifi { - label = "arv4520pw:blue:wifi"; - gpios = <&gpiomm 6 GPIO_ACTIVE_LOW>; - }; - internet2 { - label = "arv4520pw:red:internet"; - gpios = <&gpiomm 9 GPIO_ACTIVE_LOW>; - }; - /* - info is missing - */ - }; - - usb_vbus: regulator-usb-vbus { - compatible = "regulator-fixed"; - - regulator-name = "USB_VBUS"; - - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - gpio = <&gpio 28 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - ebu { - lantiq,groups = "ebu cs1"; - lantiq,function = "ebu"; - }; - pci_in { - lantiq,groups = "req1"; - lantiq,function = "pci"; - lantiq,open-drain = <1>; - lantiq,pull = <2>; - lantiq,output = <0>; - }; - pci_out { - lantiq,groups = "gnt1"; - lantiq,function = "pci"; - lantiq,output = <1>; - }; - pci_rst { - lantiq,pins = "io21"; - lantiq,open-drain = <0>; - lantiq,pull = <0>; - }; - }; -}; - -&gpiomm { - status = "okay"; - lantiq,shadow = <0x400>; -}; - -&gsw { - /* gpiomm 10 - switch */ - phy-mode = "rmii"; - mtd-mac-address = <&boardconfig 0x16>; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x800000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x00000 0x20000>; - read-only; - }; - - partition@20000 { - label = "uboot_env"; - reg = <0x20000 0x10000>; - read-only; - }; - - partition@30000 { - label = "firmware"; - reg = <0x30000 0x3c0000>; - }; - - boardconfig: partition@7f0000 { - label = "boardconfig"; - reg = <0x3f0000 0x10000>; - read-only; - }; - }; - }; -}; - -&pci0 { - status = "okay"; - lantiq,external-clock; - gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; -}; - -&usb_phy { - status = "okay"; -}; - -&usb { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; - -&vmmc { - status = "okay"; - gpios = <&gpio 31 GPIO_ACTIVE_HIGH - &gpiomm 7 GPIO_ACTIVE_HIGH>; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV4525PW.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV4525PW.dts deleted file mode 100644 index b3904d37d5..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV4525PW.dts +++ /dev/null @@ -1,162 +0,0 @@ -/dts-v1/; - -#include "danube.dtsi" - -#include - -/ { - compatible = "arcadyan,arv4525pw", "lantiq,xway", "lantiq,danube"; - model = "Speedport W501V Typ A"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - /* we dont have a power led, lets use the online led */ - led-boot = &online; - led-failsafe = &online; - - led-dsl = &dsl; - led-internet = &online; - led-wifi = &wifi; - }; - - memory@0 { - reg = <0x0 0x2000000>; - }; - - ath5k_eep { - compatible = "ath5k,eeprom"; - ath,eep-flash = <&boardconfig 0x400>; - ath,mac-offset = <0x0>; - ath,eep-swap; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - wps { - label = "wps"; - gpios = <&gpio 29 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - reset { - label = "reset"; - gpios = <&gpio 30 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - fxo { - label = "arv4525pw:green:festnetz"; - gpios = <&gpio 4 GPIO_ACTIVE_LOW>; - }; - fxs { - label = "arv4525pw:green:internet"; - gpios = <&gpio 5 GPIO_ACTIVE_LOW>; - }; - dsl: dsl { - label = "arv4525pw:green:t-dsl"; - gpios = <&gpio 6 GPIO_ACTIVE_LOW>; - }; - wifi: wifi { - label = "arv4525pw:green:wlan"; - gpios = <&gpio 8 GPIO_ACTIVE_LOW>; - }; - online: online { - label = "arv4525pw:green:online"; - gpios = <&gpio 9 GPIO_ACTIVE_LOW>; - }; - }; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - pci_in { - lantiq,groups = "req1"; - lantiq,function = "pci"; - lantiq,open-drain = <1>; - lantiq,pull = <2>; - lantiq,output = <0>; - }; - pci_out { - lantiq,groups = "gnt1"; - lantiq,function = "pci"; - lantiq,output = <1>; - }; - pci_rst { - lantiq,pins = "io21"; - lantiq,pull = <2>; - lantiq,output = <1>; - }; - relay { - lantiq,pins = "io31"; - lantiq,output = <1>; - }; - }; -}; - -/* #define ARV4525PW_PHYRESET 13 */ -&gsw { - phy-mode = "mii"; - mtd-mac-address = <&boardconfig 0x16>; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x2000000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x00000 0x10000>; - read-only; - }; - - partition@10000 { - label = "uboot_env"; - reg = <0x10000 0x10000>; - read-only; - }; - - partition@20000 { - label = "firmware"; - reg = <0x20000 0x3d0000>; - }; - - boardconfig: partition@400000 { - label = "boardconfig"; - reg = <0x3f0000 0x10000>; - read-only; - }; - }; - }; -}; - -&pci0 { - status = "okay"; - gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; -}; - -/* #define ARV4525PW_RELAY 31 */ -&vmmc { - status = "okay"; - gpios = <&gpio 31 GPIO_ACTIVE_HIGH>; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV452CQW.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV452CQW.dts deleted file mode 100644 index 203a30df5c..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV452CQW.dts +++ /dev/null @@ -1,246 +0,0 @@ -/dts-v1/; - -#include "danube.dtsi" - -#include - -/ { - compatible = "arcadyan,arv452cqw", "lantiq,xway", "lantiq,danube"; - model = "Arcor 801"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power_blue; - led-failsafe = &power_red; - led-running = &power_blue; - led-upgrade = &power_blue; - - led-dsl = &dsl_blue; - led-usb = &led_usb; - led-wifi = &wifi; - }; - - memory@0 { - reg = <0x0 0x2000000>; - }; - - ath5k_eep { - compatible = "ath5k,eeprom"; - ath,eep-flash = <&boardconfig 0x400>; - ath,mac-offset = <0x0>; - ath,eep-swap; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - rfkill { - label = "rfkill"; - gpios = <&gpio 11 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - wps { - label = "wps"; - gpios = <&gpio 29 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - reset { - label = "reset"; - gpios = <&gpio 30 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - power_blue: power0 { - label = "arv452cqw:blue:power"; - gpios = <&gpio 3 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - dsl_blue: dsl { - label = "arv452cqw:blue:dsl"; - gpios = <&gpio 4 GPIO_ACTIVE_LOW>; - }; - isdn { - label = "arv452cqw:blue:isdn"; - gpios = <&gpio 5 GPIO_ACTIVE_LOW>; - }; - power_red: power1 { - label = "arv452cqw:red:power"; - gpios = <&gpio 6 GPIO_ACTIVE_LOW>; - }; - wps { - label = "arv452cqw:blue:wps"; - gpios = <&gpio 7 GPIO_ACTIVE_LOW>; - }; - wps1 { - label = "arv452cqw:yellow:wps"; - gpios = <&gpio 9 GPIO_ACTIVE_LOW>; - }; - fxs1 { - label = "arv452cqw:blue:telefon1"; - gpios = <&gpiomm 0 GPIO_ACTIVE_LOW>; - }; - fxs2 { - label = "arv452cqw:blue:telefon2"; - gpios = <&gpiomm 1 GPIO_ACTIVE_LOW>; - }; - wps2 { - label = "arv452cqw:red:wps"; - gpios = <&gpiomm 2 GPIO_ACTIVE_LOW>; - }; - fxo { - label = "arv452cqw:blue:line"; - gpios = <&gpiomm 3 GPIO_ACTIVE_LOW>; - }; - voice { - label = "arv452cqw:blue:sprache"; - gpios = <&gpiomm 4 1>; - }; - led_usb: usb { - label = "arv452cqw:blue:usb"; - gpios = <&gpiomm 5 GPIO_ACTIVE_LOW>; - }; - wifi: wifi { - label = "arv452cqw:blue:wlan"; - gpios = <&gpiomm 6 GPIO_ACTIVE_LOW>; - }; - /* - internet blue and internet red are missing - dsl2 and dsl3 are not referenced in manual - */ - dsl2 { - label = "arv452cqw:yellow:dsl"; - gpios = <&gpiomm 8 GPIO_ACTIVE_LOW>; - }; - dsl3 { - label = "arv452cqw:red:dsl"; - gpios = <&gpiomm 9 GPIO_ACTIVE_LOW>; - }; - }; - - usb_vbus: regulator-usb-vbus { - compatible = "regulator-fixed"; - - regulator-name = "USB_VBUS"; - - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - gpio = <&gpio 28 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - ebu { - lantiq,groups = "ebu cs1"; - lantiq,function = "ebu"; - }; - pci_in { - lantiq,groups = "req1"; - lantiq,function = "pci"; - lantiq,open-drain = <1>; - lantiq,pull = <2>; - lantiq,output = <0>; - }; - pci_out { - lantiq,groups = "gnt1"; - lantiq,function = "pci"; - lantiq,output = <1>; - }; - pci_rst { - lantiq,pins = "io21"; - lantiq,pull = <0>; - lantiq,output = <1>; - }; - leds { - lantiq,pins = "io3", "io5", "io6", "io7", "io9"; - lantiq,output = <1>; - }; - }; -}; - -&gpiomm { - status = "okay"; - lantiq,shadow = <0x77f>; -}; - -/* -#define ARV452CPW_SWITCH_RESET 110 -*/ -&gsw { - phy-mode = "rmii"; - mtd-mac-address = <&boardconfig 0x16>; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x400000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x00000 0x10000>; - read-only; - }; - - partition@10000 { - label = "uboot_env"; - reg = <0x10000 0x10000>; - read-only; - }; - - partition@20000 { - label = "firmware"; - reg = <0x20000 0x3d0000>; - }; - - boardconfig: partition@3f0000 { - label = "boardconfig"; - reg = <0x3f0000 0x10000>; - read-only; - }; - }; - }; -}; - -&pci0 { - status = "okay"; - lantiq,external-clock; - gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; -}; - -&usb_phy { - status = "okay"; -}; - -&usb { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; - -&vmmc { - status = "okay"; - gpios = <&gpio 31 GPIO_ACTIVE_HIGH - &gpiomm 7 GPIO_ACTIVE_HIGH>; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV7506PW11.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV7506PW11.dts deleted file mode 100644 index 8fe22e9a44..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV7506PW11.dts +++ /dev/null @@ -1,164 +0,0 @@ -/dts-v1/; - -#include "danube.dtsi" - -#include - -/ { - compatible = "arcadyan,arv7506pw11", "lantiq,xway", "lantiq,danube"; - model = "Alice/O2 IAD 4421"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power; - led-failsafe = &power_red; - led-running = &power; - led-upgrade = &power; - - led-dsl = &dsl; - led-internet = &internet; - led-wifi = &wlan; - }; - - memory@0 { - reg = <0x0 0x4000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - rfkill { - label = "rfkill"; - gpios = <&gpio 11 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - reset { - label = "reset"; - gpios = <&gpio 30 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - wlan: wlan { - label = "arv7506pw11:green:wlan"; - gpios = <&gpio 2 GPIO_ACTIVE_LOW>; - }; - power: power { - label = "arv7506pw11:green:power"; - gpios = <&gpio 3 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - dsl: dsl { - label = "arv7506pw11:green:dsl"; - gpios = <&gpio 4 GPIO_ACTIVE_LOW>; - }; - internet: internet { - label = "arv7506pw11:green:internet"; - gpios = <&gpio 5 GPIO_ACTIVE_LOW>; - }; - power_red: power_red { - label = "arv7506pw11:red:power"; - gpios = <&gpio 6 GPIO_ACTIVE_LOW>; - }; - internet_red { - label = "arv7506pw11:red:internet"; - gpios = <&gpio 7 GPIO_ACTIVE_LOW>; - }; - info { - label = "arv7506pw11:green:info"; - gpios = <&gpio 8 GPIO_ACTIVE_LOW>; - }; - telefon { - label = "arv7506pw11:green:telefon"; - gpios = <&gpio 9 GPIO_ACTIVE_LOW>; - }; - info_red { - label = "arv7506pw11:red:info"; - gpios = <&gpio 20 GPIO_ACTIVE_LOW>; - }; - }; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - pci { - lantiq,groups = "gnt1"; - lantiq,function = "pci"; - lantiq,output = <1>; - }; - pci_rst { - lantiq,pins = "io21"; - lantiq,pull = <2>; - lantiq,output = <1>; - }; - }; -}; - -/* GPIO 19: switch reset */ -&gsw { - phy-mode = "rmii"; - mtd-mac-address = <&boardconfig 0x16>; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x800000>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x00000 0x40000>; - read-only; - }; - - partition@40000 { - label = "uboot_env"; - reg = <0x40000 0x10000>; - read-only; - }; - - partition@50000 { - label = "firmware"; - reg = <0x50000 0x7a0000>; - }; - - boardconfig: partition@7f0000 { - label = "board_config"; - reg = <0x7f0000 0x10000>; - read-only; - }; - }; - }; -}; - -&pci0 { - status = "okay"; - lantiq,external-clock; - gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; - - wifi@1814,3592 { - compatible = "pci1814,3592"; - reg = <0x7000 0 0 0 0>; - ralink,mtd-eeprom = <&boardconfig 0x410>; - ralink,mtd-eeprom-swap; - mtd-mac-address = <&boardconfig 0x16>; - mtd-mac-address-increment = <1>; - }; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV7510PW22.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV7510PW22.dts deleted file mode 100644 index 92d01b4dcc..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV7510PW22.dts +++ /dev/null @@ -1,209 +0,0 @@ -/dts-v1/; - -#include "danube.dtsi" - -#include - -/ { - compatible = "arcadyan,arv7510pw22", "lantiq,xway", "lantiq,danube"; - model = "Astoria Networks ARV7510PW22"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power; - led-failsafe = &power; - led-running = &power; - led-upgrade = &power; - - led-dsl = &internet; - led-usb = &umts; - led-wifi = &wlan; - }; - - memory@0 { - reg = <0x0 0x4000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - rfkill { - label = "rfkill"; - gpios = <&gpio 11 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - restart { - label = "restart"; - gpios = <&gpio 12 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - reset { - label = "reset"; - gpios = <&gpio 28 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - power: power { - label = "power"; - gpios = <&gpio 2 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - internet: internet { - label = "internet"; - gpios = <&gpio 4 GPIO_ACTIVE_LOW>; - }; - wlan: wlan { - label = "wlan"; - gpios = <&gpio 10 GPIO_ACTIVE_LOW>; - }; - umts: 3g { - label = "3g"; - gpios = <&gpio 15 GPIO_ACTIVE_LOW>; - }; - message { - label = "message"; - gpios = <&gpio 20 GPIO_ACTIVE_LOW>; - }; - }; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - exin { - lantiq,groups = "exin1"; - lantiq,function = "exin"; - lantiq,pull = <2>; - lantiq,output = <0>; - }; - pci_in { - lantiq,groups = "req1", "req2"; - lantiq,function = "pci"; - lantiq,open-drain = <1>; - lantiq,pull = <2>; - lantiq,output = <0>; - }; - pci_out { - lantiq,groups = "gnt1"; - lantiq,function = "pci"; - lantiq,output = <1>; - }; - pci_rst { - lantiq,pins = "io21"; - lantiq,pull = <2>; - lantiq,output = <1>; - }; - pins_out { - lantiq,pins = "io2", "io4", "io8", "io9", "io10", "io15", "io20"; - lantiq,output = <1>; - }; - pins_in { - lantiq,pins = "io11", "io12", "io28"; - lantiq,open-drain = <1>; - lantiq,pull = <2>; - lantiq,output = <0>; - }; - }; - - usb_vbus: regulator-usb-vbus { - compatible = "regulator-fixed"; - - regulator-name = "USB_VBUS"; - - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - gpio = <&gpio 8 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -&gsw { - /* Switch reset 19 */ - phy-mode = "mii"; - mtd-mac-address = <&boardconfig 0x16>; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x1000000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x00000 0x40000>; - read-only; - }; - - partition@40000 { - label = "uboot_env"; - reg = <0x40000 0x20000>; - read-only; - }; - - partition@60000 { - label = "firmware"; - reg = <0x60000 0xf80000>; - }; - - boardconfig: partition@fe0000 { - label = "board_config"; - reg = <0xfe0000 0x20000>; - read-only; - }; - }; - }; -}; - -&pci0 { - status = "okay"; - lantiq,external-clock; - interrupt-map = < - 0x7000 0 0 1 &icu0 30 - 0x7800 0 0 1 &icu0 135 - 0x7800 0 0 2 &icu0 135 - 0x7800 0 0 3 &icu0 135 - >; - gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; - req-mask = <0x3>; - - wifi@1814,3592 { - compatible = "pci1814,3592"; - reg = <0x7000 0 0 0 0>; - ralink,mtd-eeprom = <&boardconfig 0x410>; - ralink,mtd-eeprom-swap; - }; -}; - -&usb_phy { - status = "okay"; -}; - -&usb { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; - -&vmmc { - status = "okay"; - gpios = <&gpio 9 GPIO_ACTIVE_HIGH>; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV7518PW.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV7518PW.dts deleted file mode 100644 index 72f3a686b5..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV7518PW.dts +++ /dev/null @@ -1,240 +0,0 @@ -/dts-v1/; - -#include "danube.dtsi" - -#include - -/ { - compatible = "arcadyan,arv7518pw", "lantiq,xway", "lantiq,danube"; - model = "Astoria Networks ARV7518PW"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power_green; - led-failsafe = &power_red; - led-running = &power_green; - led-upgrade = &power_green; - - led-dsl = &dsl; - led-internet = &online_green; - led-usb = &led_usb; - led-wifi = &wifi; - }; - - memory@0 { - reg = <0x0 0x4000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - rfkill { - label = "rfkill"; - gpios = <&gpio 28 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - reset { - label = "reset"; - gpios = <&gpio 30 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - power_green: power { - label = "arv7518pw:green:power"; - gpios = <&gpio 2 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - dsl: dsl { - label = "arv7518pw:green:dsl"; - gpios = <&gpio 4 GPIO_ACTIVE_LOW>; - }; - online_green: online { - label = "arv7518pw:green:internet"; - gpios = <&gpio 5 GPIO_ACTIVE_LOW>; - }; - wifi: wifi { - label = "arv7518pw:green:wlan"; - gpios = <&gpio 6 GPIO_ACTIVE_LOW>; - }; - power_red: power2 { - label = "arv7518pw:red:power"; - gpios = <&gpio 7 GPIO_ACTIVE_LOW>; - }; - online2 { - label = "arv7518pw:red:internet"; - gpios = <&gpio 8 GPIO_ACTIVE_LOW>; - }; - led_usb: usb { - label = "arv7518pw:green:usb"; - gpios = <&gpio 19 GPIO_ACTIVE_LOW>; - }; - voice { - label = "arv7518pw:green:voip"; - gpios = <&gpiomm 0 GPIO_ACTIVE_LOW>; - }; - fxs1 { - label = "arv7518pw:green:phone1"; - gpios = <&gpiomm 1 GPIO_ACTIVE_LOW>; - }; - fxs2 { - label = "arv7518pw:green:phone2"; - gpios = <&gpiomm 2 GPIO_ACTIVE_LOW>; - }; - unlabeled { - label = "arv7518pw:amber:unlabeled"; - gpios = <&gpiomm 3 GPIO_ACTIVE_LOW>; - }; - wps { - label = "arv7518pw:amber:wps"; - gpios = <&gpiomm 4 GPIO_ACTIVE_LOW>; - }; - wps2 { - label = "arv7518pw:green:wps"; - gpios = <&gpiomm 5 GPIO_ACTIVE_LOW>; - }; - wps3 { - label = "arv7518pw:red:wps"; - gpios = <&gpiomm 6 GPIO_ACTIVE_LOW>; - }; - }; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - ebu { - lantiq,groups = "ebu cs1"; - lantiq,function = "ebu"; - }; - pci_in { - lantiq,groups = "req1"; - lantiq,function = "pci"; - lantiq,open-drain = <1>; - lantiq,pull = <2>; - lantiq,output = <0>; - }; - pci_out { - lantiq,groups = "gnt1"; - lantiq,function = "pci"; - lantiq,pull = <0>; - lantiq,output = <1>; - }; - pci_rst { - lantiq,pins = "io21"; - lantiq,pull = <2>; - lantiq,output = <1>; - }; - leds { - lantiq,pins = "io2", "io4", "io5", "io6", "io7", "io8", "io19"; - lantiq,output = <1>; - }; - keys { - lantiq,pins = "io28", "io30"; - lantiq,output = <0>; - lantiq,pull = <2>; - lantiq,open-drain = <1>; - }; - }; - - usb_vbus: regulator-usb-vbus { - compatible = "regulator-fixed"; - - regulator-name = "USB_VBUS"; - - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - gpio = <&gpio 14 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -&gpiomm { - status = "okay"; - lantiq,shadow = <0x0>; -}; - -/* -#define SWITCH_RESET 13 -*/ -&gsw { - phy-mode = "mii"; - mtd-mac-address = <&boardconfig 0x16>; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x2000000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x00000 0x10000>; - read-only; - }; - - partition@10000 { - label = "uboot_env"; - reg = <0x10000 0x10000>; - }; - - partition@20000 { - label = "firmware"; - reg = <0x20000 0x7d0000>; - }; - - boardconfig: partition@400000 { - label = "boardconfig"; - reg = <0x7f0000 0x10000>; - read-only; - }; - }; - }; -}; - -&pci0 { - status = "okay"; - gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; - lantiq,external-clock; - req-mask = <0xf>; - - wifi@168c,0029 { - compatible = "pci168c,0029"; - reg = <0x7000 0 0 0 0>; - qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:00:0e.0.bin */ - mtd-mac-address = <&boardconfig 0x16>; - mtd-mac-address-increment = <1>; - }; -}; - -&usb_phy { - status = "okay"; -}; - -&usb { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; - -&vmmc { - status = "okay"; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV7519PW.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV7519PW.dts deleted file mode 100644 index bcb3b502af..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV7519PW.dts +++ /dev/null @@ -1,229 +0,0 @@ -/dts-v1/; - -#include "danube.dtsi" - -#include - -/ { - compatible = "arcadyan,arv7519pw", "lantiq,xway", "lantiq,danube"; - model = "Astoria Networks ARV7519PW"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power; - led-failsafe = &power2; - led-running = &power; - led-upgrade = &power; - - led-dsl = &dsl; - led-internet = &online; - led-wifi = &wifi; - }; - - memory@0 { - reg = <0x0 0x4000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - rfkill { - label = "rfkill"; - gpios = <&gpio 11 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - reset { - label = "reset"; - gpios = <&gpio 28 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - power: power { - label = "power"; - gpios = <&gpio 2 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - power2: power2 { - label = "power2"; - gpios = <&gpio 14 GPIO_ACTIVE_LOW>; - }; - online: online { - label = "online"; - gpios = <&gpio 3 GPIO_ACTIVE_LOW>; - }; - online2 { - label = "online2"; - gpios = <&gpio 30 GPIO_ACTIVE_LOW>; - }; - wifi: wifi { - label = "wifi"; - gpios = <&gpio 12 GPIO_ACTIVE_LOW>; - }; - wifi2 { - label = "wifi2"; - gpios = <&gpio 10 GPIO_ACTIVE_LOW>; - }; - wifi3 { - label = "wifi3"; - gpios = <&gpio 6 GPIO_ACTIVE_LOW>; - }; - voice { - label = "voice"; - gpios = <&gpio 31 GPIO_ACTIVE_LOW>; - }; - wps { - label = "wps"; - gpios = <&gpio 15 GPIO_ACTIVE_LOW>; - }; - wps2 { - label = "wps2"; - gpios = <&gpio 7 GPIO_ACTIVE_LOW>; - }; - wps3 { - label = "wps3"; - gpios = <&gpio 23 GPIO_ACTIVE_LOW>; - }; - dsl: dsl { - label = "dsl"; - gpios = <&gpio 4 GPIO_ACTIVE_LOW>; - }; - lan { - label = "lan"; - gpios = <&gpio 1 GPIO_ACTIVE_LOW>; - }; - tv { - label = "tv"; - gpios = <&gpio 20 GPIO_ACTIVE_LOW>; - }; - upgrade { - label = "upgrade"; - gpios = <&gpio 29 GPIO_ACTIVE_LOW>; - }; - }; - - /* is there another way to "reserve" the GPIO? */ - gpio_export { - compatible = "gpio-export"; - #size-cells = <0>; - - switch { - gpio-export,name = "switch"; - gpio-export,output = <1>; - gpios = <&gpio 19 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - ebu { - lantiq,groups = "ebu cs1"; - lantiq,function = "ebu"; - }; - pci_in { - lantiq,groups = "req1"; - lantiq,function = "pci"; - lantiq,open-drain = <1>; - lantiq,pull = <2>; - lantiq,output = <0>; - }; - pci_out { - lantiq,groups = "gnt1"; - lantiq,function = "pci"; - lantiq,pull = <0>; - lantiq,output = <1>; - }; - pci_rst { - lantiq,pins = "io21"; - lantiq,pull = <2>; - lantiq,output = <1>; - }; - switch_rst { - lantiq,pins = "io19"; - lantiq,pull = <2>; - lantiq,output = <1>; - }; - }; -}; - -&gsw { - phy-mode = "mii"; - mtd-mac-address = <&boardconfig 0x16>; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x2000000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x00000 0x40000>; - read-only; - }; - - partition@40000 { - label = "uboot_env"; - reg = <0x40000 0x20000>; - }; - - partition@60000 { - label = "firmware"; - reg = <0x60000 0xf80000>; - }; - - boardconfig: partition@fe0000 { - label = "board_config"; - reg = <0xfe0000 0x20000>; - read-only; - }; - }; - }; -}; - -&pci0 { - status = "okay"; - lantiq,external-clock; - gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; - req-mask = <0xf>; - - wifi@0,0 { - compatible = "pci0,0"; - reg = <0x7000 0 0 0 0>; - ralink,mtd-eeprom = <&boardconfig 0x410>; - ralink,mtd-eeprom-swap; - }; -}; - -&usb_phy { - status = "okay"; -}; - -/* warning: passive port only works with active devices */ -&usb { - status = "okay"; -}; - -&vmmc { - status = "okay"; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV7519RW22.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV7519RW22.dts deleted file mode 100644 index baa9adcc9c..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV7519RW22.dts +++ /dev/null @@ -1,254 +0,0 @@ -/dts-v1/; - -#include "vr9.dtsi" - -#include -#include - -/ { - compatible = "arcadyan,arv7519rw22", "lantiq,xway", "lantiq,vr9"; - model = "Orange Livebox 2.1"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power_green; - led-failsafe = &power_green; - led-running = &power_green; - led-upgrade = &power_green; - - led-dsl = &internet_green; - }; - - memory@0 { - reg = <0x0 0x8000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - reset { - label = "reset"; - gpios = <&gpio 6 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - rfkill { - label = "rfkill"; - gpios = <&gpio 33 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - wps { - label = "wps"; - gpios = <&gpio 37 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - - lan_green { - label = "arv7519rw22:green:lan"; - gpios = <&gpio 2 GPIO_ACTIVE_LOW>; - }; - internet_red { - label = "arv7519rw22:red:internet"; - gpios = <&gpio 10 GPIO_ACTIVE_LOW>; - }; - power_green: power_green { - label = "arv7519rw22:green:power"; - gpios = <&gpio 14 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - alarm_blue { - label = "arv7519rw22:blue:alarm"; - gpios = <&gpio 15 GPIO_ACTIVE_LOW>; - }; - internet_orange { - label = "arv7519rw22:orange:internet"; - gpios = <&gpio 19 GPIO_ACTIVE_LOW>; - }; - internet_green: internet_green { - label = "arv7519rw22:green:internet"; - gpios = <&gpio 28 GPIO_ACTIVE_LOW>; - }; - voice_green { - label = "arv7519rw22:green:voice"; - gpios = <&gpio 29 GPIO_ACTIVE_LOW>; - }; - }; - - usb_vbus: regulator-usb-vbus { - compatible = "regulator-fixed"; - - regulator-name = "USB_VBUS"; - - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - gpio = <&gpio 32 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -ð0 { - lan: interface@0 { - compatible = "lantiq,xrx200-pdi"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - mtd-mac-address = <&boardconfig 0x16>; - lantiq,switch; - - ethernet@0 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <0>; - phy-mode = "rgmii"; - phy-handle = <&phy0>; - }; - ethernet@1 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <4>; - phy-mode = "mii"; - phy-handle = <&phy13>; - }; - ethernet@2 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <5>; - phy-mode = "mii"; - phy-handle = <&phy14>; - }; - ethernet@3 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <2>; - phy-mode = "mii"; - phy-handle = <&phy11>; - }; - ethernet@4 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <3>; - phy-mode = "mii"; - phy-handle = <&phy12>; - }; - }; - - mdio@0 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "lantiq,xrx200-mdio"; - reg = <0>; - - phy0: ethernet-phy@0 { - reg = <0x0>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - phy11: ethernet-phy@11 { - reg = <0x11>; - compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; - }; - phy12: ethernet-phy@12 { - reg = <0x12>; - compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; - }; - phy13: ethernet-phy@13 { - reg = <0x13>; - compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; - }; - phy14: ethernet-phy@14 { - reg = <0x14>; - compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; - }; - }; -}; - -&gphy0 { - lantiq,gphy-mode = ; -}; - -&gphy1 { - lantiq,gphy-mode = ; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - mdio { - lantiq,groups = "mdio"; - lantiq,function = "mdio"; - }; - pcie-rst { - lantiq,pins = "io21"; - lantiq,pull = <0>; - lantiq,output = <1>; - }; - }; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x2000000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x0 0x60000>; - read-only; - }; - - partition@60000 { - label = "uboot-env"; - reg = <0x60000 0x20000>; - read-only; - }; - - partition@80000 { - label = "firmware"; - reg = <0x80000 0x1f00000>; - }; - - boardconfig: partition@1f80000 { - label = "boardconfig"; - reg = <0x1f80000 0x80000>; - read-only; - }; - }; - }; -}; - -&pcie0 { - status = "okay"; - gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; -}; - -&usb_phy0 { - status = "okay"; -}; - -&usb_phy1 { - status = "okay"; -}; - -&usb0 { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; - -&usb1 { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV7525PW.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV7525PW.dts deleted file mode 100644 index a395d4ff45..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV7525PW.dts +++ /dev/null @@ -1,152 +0,0 @@ -/dts-v1/; - -#include "danube.dtsi" - -#include - -/ { - compatible = "arcadyan,arv7525pw", "lantiq,xway", "lantiq,danube"; - model = "Speedport W303V Typ A"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power_green; - led-failsafe = &power_red; - led-running = &power_green; - led-upgrade = &power_green; - - led-dsl = &power_green; - led-internet = &online; - led-wifi = &wifi; - }; - - memory@0 { - reg = <0x0 0x2000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - wps { - label = "wps"; - gpios = <&gpio 29 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - reset { - label = "reset"; - gpios = <&gpio 30 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - power_green: power { - label = "arv7525pw:green:power"; - gpios = <&gpio 3 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - power_red: power1 { - label = "arv7525pw:red:power"; - gpios = <&gpio 4 GPIO_ACTIVE_LOW>; - }; - online: online { - label = "arv7525pw:green:online"; - gpios = <&gpio 5 GPIO_ACTIVE_LOW>; - }; - voice { - label = "arv7525pw:green:telefonie"; - gpios = <&gpio 6 GPIO_ACTIVE_LOW>; - }; - voice2 { - label = "arv7525pw:red:telefonie"; - gpios = <&gpio 8 GPIO_ACTIVE_LOW>; - }; - wifi: wifi { - label = "arv7525pw:green:wlan"; - gpios = <&gpio 9 GPIO_ACTIVE_LOW>; - }; - }; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - exin { - lantiq,groups = "exin1"; - lantiq,function = "exin"; - }; - pci { - lantiq,groups = "gnt1", "req1"; - lantiq,function = "pci"; - }; - }; -}; - -&gsw { - phy-mode = "mii"; - mtd-mac-address = <&boardconfig 0x16>; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x2000000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x00000 0x10000>; - read-only; - }; - - partition@10000 { - label = "uboot_env"; - reg = <0x10000 0x10000>; - read-only; - }; - - partition@20000 { - label = "firmware"; - reg = <0x20000 0x3d0000>; - }; - - boardconfig: partition@400000 { - label = "board_config"; - reg = <0x3f0000 0x10000>; - read-only; - }; - }; - }; -}; - -&pci0 { - status = "okay"; - interrupt-map = <0x7000 0 0 1 &icu0 135 1>; - - wifi@0,0 { - compatible = "pci0,0"; - reg = <0x7000 0 0 0 0>; - ralink,mtd-eeprom = <&boardconfig 0x410>; - }; -}; - -&vmmc { - status = "okay"; - gpios = <&gpio 31 GPIO_ACTIVE_HIGH>; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV752DPW.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV752DPW.dts deleted file mode 100644 index 5f877723f6..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV752DPW.dts +++ /dev/null @@ -1,246 +0,0 @@ -/dts-v1/; - -#include "danube.dtsi" - -#include - -/ { - compatible = "arcadyan,arv752dpw", "lantiq,xway", "lantiq,danube"; - model = "Arcor 802"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power_red; - led-failsafe = &power_blue; - led-running = &power_red; - led-upgrade = &power_red; - - led-dsl = &internet_red; - led-usb = &umts; - led-wifi = &wifi; - }; - - memory@0 { - reg = <0x0 0x4000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - wps { - label = "wps"; - gpios = <&gpio 11 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - restart { - label = "restart"; - gpios = <&gpio 12 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - dsl { - label = "dsl"; - gpios = <&gpio 13 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - reset { - label = "reset"; - gpios = <&gpio 30 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - power_blue: power1 { - label = "arv752dpw:blue:power"; - gpios = <&gpio 3 GPIO_ACTIVE_LOW>; - }; - internet_red: internet { - label = "arv752dpw:red:internet"; - gpios = <&gpio 4 GPIO_ACTIVE_LOW>; - }; - message { - label = "arv752dpw:red:message"; - gpios = <&gpio 5 GPIO_ACTIVE_LOW>; - }; - power_red: power { - label = "arv752dpw:red:power"; - gpios = <&gpio 6 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - voice1 { - label = "arv752dpw:red:voice"; - gpios = <&gpio 8 GPIO_ACTIVE_LOW>; - }; - umts: umts { - label = "arv752dpw:red:umts"; - gpios = <&gpiomm 3 GPIO_ACTIVE_LOW>; - }; - wifi: wifi { - label = "arv752dpw:red:wifi"; - gpios = <&gpiomm 4 GPIO_ACTIVE_LOW>; - }; - fxs1 { - label = "arv752dpw:green:tae-n"; - gpios = <&gpiomm 5 GPIO_ACTIVE_LOW>; - }; - fxs2 { - label = "arv752dpw:green:tae-u"; - gpios = <&gpiomm 6 GPIO_ACTIVE_LOW>; - }; - fxo { - label = "arv752dpw:green:isdn"; - gpios = <&gpiomm 7 GPIO_ACTIVE_LOW>; - }; - internet2 { - label = "arv752dpw:blue:internet"; - gpios = <&gpiomm 8 GPIO_ACTIVE_LOW>; - }; - voice2 { - label = "arv752dpw:blue:voice"; - gpios = <&gpiomm 9 GPIO_ACTIVE_LOW>; - }; - }; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - ebu { - lantiq,groups = "ebu cs1"; - lantiq,function = "ebu"; - }; - exin { - lantiq,groups = "exin1"; - lantiq,function = "exin"; - lantiq,pull = <2>; - lantiq,output = <0>; - }; - pci_in { - lantiq,groups = "req2", "req1"; - lantiq,function = "pci"; - lantiq,open-drain = <1>; - lantiq,pull = <2>; - lantiq,output = <0>; - }; - pci_out { - lantiq,groups = "gnt1"; - lantiq,function = "pci"; - lantiq,output = <1>; - }; - pci_rst { - lantiq,pins = "io21"; - lantiq,pull = <2>; - lantiq,output = <1>; - }; - leds { - lantiq,pins = "io3", "io5", "io6", "io8"; - lantiq,output = <1>; - lantiq,pull = <0>; - }; - keys { - lantiq,pins = "io11", "io12", "io13", "io28"; - lantiq,output = <0>; - lantiq,pull = <2>; - lantiq,open-drain = <1>; - }; - }; - - usb_vbus: regulator-usb-vbus { - compatible = "regulator-fixed"; - - regulator-name = "USB_VBUS"; - - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - gpio = <&gpiomm 0 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -&gpiomm { - status = "okay"; - lantiq,shadow = <0x3>; -}; - -&gsw { - phy-mode = "rmii"; - mtd-mac-address = <&boardconfig 0x16>; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x800000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x00000 0x10000>; - read-only; - }; - - partition@10000 { - label = "uboot_env"; - reg = <0x10000 0x10000>; - read-only; - }; - - partition@20000 { - label = "firmware"; - reg = <0x20000 0x7d0000>; - }; - - boardconfig: partition@7f0000 { - label = "board_config"; - reg = <0x7f0000 0x10000>; - read-only; - }; - }; - }; -}; - -&pci0 { - status = "okay"; - lantiq,external-clock; - gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; - interrupt-map = <0x7000 0 0 1 &icu0 135>; - req-mask = <0x3>; - - wifi@1814,0601 { - compatible = "pci1814,0601"; - reg = <0x7000 0 0 0 0>; - ralink,mtd-eeprom = <&boardconfig 0x410>; - ralink,mtd-eeprom-swap; - }; -}; - -&usb_phy { - status = "okay"; -}; - -&usb { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; - -&vmmc { - status = "okay"; - gpios = <&gpiomm 1 GPIO_ACTIVE_HIGH>; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV752DPW22.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV752DPW22.dts deleted file mode 100644 index 1d4d662ab3..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV752DPW22.dts +++ /dev/null @@ -1,268 +0,0 @@ -/dts-v1/; - -#include "danube.dtsi" - -#include - -/ { - compatible = "arcadyan,arv752dpw22", "lantiq,xway", "lantiq,danube"; - model = "Arcor 803"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power_red; - led-failsafe = &power_blue; - led-running = &power_red; - led-upgrade = &power_red; - - led-dsl = &internet_red; - led-usb = &umts; - led-wifi = &wifi; - }; - - memory@0 { - reg = <0x0 0x4000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - wps { - label = "wps"; - gpios = <&gpio 11 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - restart { - label = "restart"; - gpios = <&gpio 12 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - dsl { - label = "dsl"; - gpios = <&gpio 13 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - reset { - label = "reset"; - gpios = <&gpio 28 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - power_blue: power1 { - label = "arv752dpw22:blue:power"; - gpios = <&gpio 3 GPIO_ACTIVE_LOW>; - }; - internet_red: internet { - label = "arv752dpw22:red:internet"; - gpios = <&gpio 4 GPIO_ACTIVE_LOW>; - }; - message { - label = "arv752dpw22:red:message"; - gpios = <&gpio 5 GPIO_ACTIVE_LOW>; - }; - power_red: power { - label = "arv752dpw22:red:power"; - gpios = <&gpio 6 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - voice1 { - label = "arv752dpw22:red:voice"; - gpios = <&gpio 8 GPIO_ACTIVE_LOW>; - }; - umts: umts { - label = "arv752dpw22:red:umts"; - gpios = <&gpiomm 3 GPIO_ACTIVE_LOW>; - }; - wifi: wifi { - label = "arv752dpw22:red:wifi"; - gpios = <&gpiomm 4 GPIO_ACTIVE_LOW>; - }; - fxs1 { - label = "arv752dpw22:green:tae-n"; - gpios = <&gpiomm 5 GPIO_ACTIVE_LOW>; - }; - fxs2 { - label = "arv752dpw22:green:tae-u"; - gpios = <&gpiomm 6 GPIO_ACTIVE_LOW>; - }; - fxo { - label = "arv752dpw22:green:isdn"; - gpios = <&gpiomm 7 GPIO_ACTIVE_LOW>; - }; - internet2 { - label = "arv752dpw22:blue:internet"; - gpios = <&gpiomm 8 GPIO_ACTIVE_LOW>; - }; - voice2 { - label = "arv752dpw22:blue:voice"; - gpios = <&gpiomm 9 GPIO_ACTIVE_LOW>; - }; - eth1 { - label = "arv752dpw22:green:lan1"; - gpios = <&gpiomm 11 GPIO_ACTIVE_LOW>; - }; - eth2 { - label = "arv752dpw22:green:lan2"; - gpios = <&gpiomm 12 GPIO_ACTIVE_LOW>; - }; - eth3 { - label = "arv752dpw22:green:lan3"; - gpios = <&gpiomm 13 GPIO_ACTIVE_LOW>; - }; - eth4 { - label = "arv752dpw22:green:lan4"; - gpios = <&gpiomm 14 GPIO_ACTIVE_LOW>; - }; - }; - - usb_vbus: regulator-usb-vbus { - compatible = "regulator-fixed"; - - regulator-name = "USB_VBUS"; - - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - gpio = <&gpiomm 0 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - ebu { - lantiq,groups = "ebu cs1"; - lantiq,function = "ebu"; - }; - exin { - lantiq,groups = "exin1"; - lantiq,function = "exin"; - lantiq,pull = <2>; - lantiq,output = <0>; - }; - pci_in { - lantiq,groups = "req1"; - lantiq,function = "pci"; - lantiq,pull = <2>; - lantiq,output = <0>; - }; - pci_out { - lantiq,groups = "gnt1"; - lantiq,function = "pci"; - lantiq,open-drain = <1>; - lantiq,output = <1>; - }; - pci_rst { - lantiq,pins = "io21"; - lantiq,open-drain = <1>; - lantiq,output = <1>; - }; - leds { - lantiq,pins = "io3", "io5", "io6", "io8"; - lantiq,open-drain = <1>; - lantiq,output = <1>; - }; - buttons { - lantiq,pins = "io11", "io12", "io13", "io28"; - lantiq,pull = <2>; - lantiq,output = <0>; - }; - }; -}; - - -&gpiomm { - status = "okay"; - lantiq,shadow = <3>; -}; - -&gsw { - phy-mode = "mii"; - mtd-mac-address = <&boardconfig 0x16>; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x800000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x00000 0x30000>; - read-only; - }; - - partition@10000 { - label = "uboot_env"; - reg = <0x30000 0x10000>; - read-only; - }; - - partition@20000 { - label = "firmware"; - reg = <0x40000 0x7b0000>; - }; - - boardconfig: partition@7f0000 { - label = "board_config"; - reg = <0x7f0000 0x10000>; - read-only; - }; - }; - }; -}; - -&pci0 { - status = "okay"; - lantiq,external-clock; - interrupt-map = < - 0x7000 0 0 1 &icu0 30 - 0x7800 0 0 1 &icu0 135 - 0x7800 0 0 2 &icu0 135 - 0x7800 0 0 3 &icu0 135 - >; - gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; - req-mask = <0x3>; - - wifi@1814,3592 { - compatible = "pci1814,3592"; - reg = <0x7000 0 0 0 0>; - ralink,mtd-eeprom = <&boardconfig 0x410>; - ralink,mtd-eeprom-swap; - mtd-mac-address = <&boardconfig 0x16>; - }; -}; - -&usb_phy { - status = "okay"; -}; - -&usb { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; - -&vmmc { - status = "okay"; - gpios = <&gpiomm 1 GPIO_ACTIVE_HIGH>; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV8539PW22.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV8539PW22.dts deleted file mode 100644 index 1e55d81590..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ARV8539PW22.dts +++ /dev/null @@ -1,192 +0,0 @@ -/dts-v1/; - -#include "danube.dtsi" - -#include - -/ { - compatible = "arcadyan,arv8539pw22", "lantiq,xway", "lantiq,danube"; - model = "Speedport W 504V Typ A"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power_green; - led-failsafe = &power_red; - led-running = &power_green; - led-upgrade = &power_green; - - led-dsl = &dsl_green; - led-internet = &online_green; - led-wifi = &wireless_green; - }; - - memory@0 { - reg = <0x0 0x4000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - wlan { - label = "wlan"; - gpios = <&gpio 29 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - reset { - label = "reset"; - gpios = <&gpio 30 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - /* key DECT is missing */ - }; - - gpio-leds { - compatible = "gpio-leds"; - - power_green: power-green { - label = "arv8539pw22:green:power"; - gpios = <&gpio 24 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - power_red: power-red { - label = "arv8539pw22:red:power"; - gpios = <&gpio 4 GPIO_ACTIVE_LOW>; - }; - - dsl_green: dsl-green { - label = "arv8539pw22:green:dsl"; - gpios = <&gpio 5 GPIO_ACTIVE_LOW>; - }; - - online_green: online-green { - label = "arv8539pw22:green:online"; - gpios = <&gpio 6 GPIO_ACTIVE_LOW>; - }; - - wireless_green: wireless-green { - label = "arv8539pw22:green:wlan"; - gpios = <&gpio 8 GPIO_ACTIVE_LOW>; - }; - /* - telefonie green is missing - */ - }; - - usb_vbus: regulator-usb-vbus { - compatible = "regulator-fixed"; - - regulator-name = "USB_VBUS"; - - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - gpio = <&gpio 14 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - pci_in { - lantiq,groups = "req1"; - lantiq,function = "pci"; - lantiq,open-drain = <1>; - lantiq,pull = <2>; - lantiq,output = <0>; - }; - pci_out { - lantiq,groups = "gnt1"; - lantiq,function = "pci"; - lantiq,output = <1>; - }; - pci_rst { - lantiq,pins = "io21"; - lantiq,pull = <2>; - lantiq,output = <1>; - }; - relay { - lantiq,pins = "io31"; - lantiq,output = <1>; - }; - }; -}; - -&gsw { - phy-mode = "mii"; - mtd-mac-address = <&art 0x16>; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x800000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x00000 0x30000>; /* 192 KiB */ - read-only; - }; - - partition@30000 { - label = "uboot"; - reg = <0x30000 0x10000>; /* 64 KiB */ - read-only; - }; - - partition@40000 { - label = "firmware"; - reg = <0x40000 0x7B0000>; /* 7872 KiB */ - }; - - art: partition@7F0000 { - label = "art"; - reg = <0x7F0000 0x10000>; /* 64 KiB*/ - read-only; - }; - }; - }; -}; - -&pci0 { - status = "okay"; - gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; - - wifi@168c,0029 { - compatible = "pci168c,0029"; - reg = <0x7000 0 0 0 0>; - qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:00:0e.0.bin */ - mtd-mac-address = <&art 0x16>; - mtd-mac-address-increment = <1>; - }; -}; - -&usb_phy { - status = "okay"; -}; - -&usb { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; - -&vmmc { - status = "okay"; - gpios = <&gpio 31 GPIO_ACTIVE_HIGH>; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ASL56026.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ASL56026.dts deleted file mode 100644 index 90bfcabcb5..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ASL56026.dts +++ /dev/null @@ -1,171 +0,0 @@ -/dts-v1/; - -#include "vr9.dtsi" - -#include -#include - -/ { - compatible = "alphanetworks,asl56026", "lantiq,xway", "lantiq,vr9"; - model = "BT OpenReach VDSL Modem"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power_green; - led-failsafe = &power_red; - led-running = &power_green; - led-upgrade = &power_green; - - led-dsl = &dsl; - }; - - memory@0 { - reg = <0x0 0x2000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - reset { - label = "reset"; - gpios = <&gpio 40 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - - dsl: dsl { - label = "asl56026:green:dsl"; - gpios = <&gpio 6 GPIO_ACTIVE_LOW>; - }; - - /* power-* is a bicolour led */ - power_green: power_green { - label = "asl56026:green:power"; - gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - - power_red: power_red { - label = "asl56026:red:power"; - gpios = <&gpio 18 GPIO_ACTIVE_HIGH>; - }; - }; - - gpio_export { - compatible = "gpio-export"; - #size-cells = <0>; - - power_led_blink { - gpio-export,name = "power_led_blink"; - gpio-export,output = <0>; - gpios = <&gpio 16 GPIO_ACTIVE_LOW>; - }; - }; -}; - -ð0 { - lan: interface@0 { - compatible = "lantiq,xrx200-pdi"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - lantiq,switch; - - ethernet@2 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <2>; - phy-mode = "mii"; - phy-handle = <&phy11>; - }; - - ethernet@3 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <3>; - phy-mode = "mii"; - phy-handle = <&phy14>; - }; - }; - - mdio@0 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "lantiq,xrx200-mdio"; - reg = <0>; - - phy11: ethernet-phy@11 { - reg = <0x11>; - compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; - }; - - phy14: ethernet-phy@14 { - reg = <0x14>; - compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; - }; - }; -}; - -&gphy0 { - lantiq,gphy-mode = ; -}; - -&gphy1 { - lantiq,gphy-mode = ; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - mdio { - lantiq,groups = "mdio"; - lantiq,function = "mdio"; - }; - }; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x0800000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x0 0x30000>; - }; - - partition@30000 { - label = "uboot_env"; - reg = <0x30000 0x10000>; - }; - - partition@40000 { - label = "firmware"; - reg = <0x40000 0x750000>; - }; - - partition@790000 { - label = "ddrconfig"; - reg = <0x790000 0x70000>; - read-only; - }; - }; - }; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/BTHOMEHUBV2B.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/BTHOMEHUBV2B.dts deleted file mode 100644 index e126065ea6..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/BTHOMEHUBV2B.dts +++ /dev/null @@ -1,263 +0,0 @@ -/dts-v1/; - -#include "danube.dtsi" - -#include - -/ { - compatible = "bt,homehub-v2b", "lantiq,xway", "lantiq,danube"; - model = "BT Home Hub 2B"; /* SoC: Lantiq Danube-S PSB 50712 @ 333MHz V1.3/1.5 */ - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power_orange; - led-failsafe = &power_red; - led-running = &power_blue; - led-upgrade = &power_blue; - - led-dsl = &broadband_blue; - led-wifi = &wireless_blue; - }; - - memory@0 { /* RAM: Samsung K4H511638F-LC 64MB */ - reg = <0x0 0x4000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - reset { - label = "reset"; - gpios = <&gpio 2 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - findhandset { - label = "findhandset"; - gpios = <&gpio 15 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - wps { - label = "wps"; - gpios = <&gpio 22 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - - upgrading-orange { - label = "bthomehubv2b:orange:upgrading"; - gpios = <&gpios 5 GPIO_ACTIVE_HIGH>; - }; - - phone-orange { - label = "bthomehubv2b:orange:phone"; - gpios = <&gpios 6 GPIO_ACTIVE_HIGH>; - }; - phone-blue { - label = "bthomehubv2b:blue:phone"; - gpios = <&gpios 7 GPIO_ACTIVE_HIGH>; - }; - - wireless-orange { - label = "bthomehubv2b:orange:wireless"; - gpios = <&gpios 8 GPIO_ACTIVE_HIGH>; - }; - wireless_blue: wireless-blue { - label = "bthomehubv2b:blue:wireless"; - gpios = <&gpios 9 GPIO_ACTIVE_HIGH>; - }; - - broadband-red { - label = "bthomehubv2b:red:broadband"; - gpios = <&gpios 10 GPIO_ACTIVE_HIGH>; - }; - broadband-orange { - label = "bthomehubv2b:orange:broadband"; - gpios = <&gpios 11 GPIO_ACTIVE_HIGH>; - }; - broadband_blue: broadband-blue { - label = "bthomehubv2b:blue:broadband"; - gpios = <&gpios 12 GPIO_ACTIVE_HIGH>; - }; - - power_red: power-red { - label = "bthomehubv2b:red:power"; - gpios = <&gpios 13 GPIO_ACTIVE_HIGH>; - }; - power_orange: power-orange { - label = "bthomehubv2b:orange:power"; - gpios = <&gpios 14 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - power_blue: power-blue { - label = "bthomehubv2b:blue:power"; - gpios = <&gpios 15 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - nand_out { - lantiq,groups = "nand cle", "nand ale"; - lantiq,function = "ebu"; - lantiq,output = <1>; - lantiq,open-drain = <0>; - lantiq,pull = <0>; - }; - nand_cs1 { - lantiq,groups = "nand cs1"; - lantiq,function = "ebu"; - lantiq,open-drain = <0>; - lantiq,pull = <0>; - }; - exin { - lantiq,groups = "exin1"; - lantiq,function = "exin"; - }; - pci_in { - lantiq,groups = "req1"; - lantiq,function = "pci"; - lantiq,output = <0>; - lantiq,open-drain = <1>; - lantiq,pull = <2>; - }; - pci_out { - lantiq,groups = "gnt1"; - lantiq,function = "pci"; - lantiq,output = <1>; - lantiq,open-drain = <0>; - lantiq,pull = <0>; - }; - - pci_rst { - lantiq,pins = "io21"; - lantiq,output = <1>; - lantiq,open-drain = <0>; - }; - - btn_in { - lantiq,pins = "io2", "io15", "io22"; - lantiq,output = <0>; - lantiq,open-drain = <1>; - lantiq,pull = <2>; - }; - }; -}; - -&gpios { - status = "okay"; -}; - -&gsw { - phy-mode = "rmii"; -}; - -&localbus { - nor@0 { /* NOR Flash: Spansion S29AL004D 512KB */ - compatible = "lantiq,nor"; /* "AMD AM29LV400BB" compatible on 3.3.8 */ - lantiq,cs = <0>; - bank-width = <2>; - reg = <0 0x0 0x80000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x00000 0x40000>; /* 256KB */ - }; - - partition@40000 { - label = "uboot_env"; - reg = <0x40000 0x10000>; /* 64KB */ - }; - - partition@50000 { - label = "rg_conf_1"; - reg = <0x50000 0x10000>; - }; - - partition@60000 { - label = "rg_conf_2"; - reg = <0x60000 0x10000>; - }; - - partition@70000 { - label = "rg_conf_factory"; - reg = <0x70000 0x10000>; - }; - }; - }; - - nand@1 { /* NAND Flash: Samsung K9F5608U0D-JIB0 32MB */ - compatible = "lantiq,nand-xway"; - lantiq,cs = <1>; - bank-width = <2>; - reg = <1 0x0 0x2000000 >; - #address-cells = <1>; - #size-cells = <1>; - req-mask = <0x1>; /* PCI request lines to mask during NAND access */ - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - ath9k_cal: partition@0 { - label = "art"; /* Atheros 9160 wifi b/g/n radio EEPROM */ - reg = <0x00000 0x4000>; - read-only; - }; - - partition@4000 { - label = "kernel"; - reg = <0x4000 0x200000>; - }; - - partition@164000 { - label = "ubi"; - reg = <0x204000 0x1DFC000>; - }; - }; - }; -}; - -&pci0 { - status = "okay"; - gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; - - wifi@168c,0027 { - compatible = "pci168c,0027"; - reg = <0x7000 0 0 0 0>; - qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:00:0e.0.bin */ - }; -}; - -&usb_phy { - status = "okay"; -}; - -&usb { - status = "okay"; -}; - -&vmmc { - status = "okay"; - gpios = <&gpio 31 GPIO_ACTIVE_HIGH>; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/BTHOMEHUBV3A.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/BTHOMEHUBV3A.dts deleted file mode 100644 index b854ac0a99..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/BTHOMEHUBV3A.dts +++ /dev/null @@ -1,216 +0,0 @@ -/dts-v1/; - -#include "ar9.dtsi" - -#include - -/ { - compatible = "bt,homehub-v3a", "lantiq,xway", "lantiq,ar9"; - model = "BT Home Hub 3A"; /* SoC: Lantiq ar9 @ 333MHz */ - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power_orange; - led-failsafe = &power_red; - led-running = &power_blue; - led-upgrade = &power_blue; - - led-dsl = &broadband_blue; - led-wifi = &wireless_blue; - }; - - memory@0 { /* RAM: Samsung K4H511638F-LC 64MB */ - reg = <0x0 0x4000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - reset { - label = "reset"; - gpios = <&gpio 54 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - restart { - label = "restart"; - gpios = <&gpio 52 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - wps { - label = "wps"; - gpios = <&gpio 53 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - - wireless-red { - label = "bthomehubv3a:red:wireless"; - gpios = <&gpio 2 GPIO_ACTIVE_LOW>; - }; - wireless-orange { - label = "bthomehubv3a:orange:wireless"; - gpios = <&gpio 6 GPIO_ACTIVE_LOW>; - }; - wireless_blue: wireless-blue { - label = "bthomehubv3a:blue:wireless"; - gpios = <&gpio 9 GPIO_ACTIVE_LOW>; - }; - - broadband-red { - label = "bthomehubv3a:red:broadband"; - gpios = <&gpio 11 GPIO_ACTIVE_LOW>; - }; - broadband-orange { - label = "bthomehubv3a:orange:broadband"; - gpios = <&gpio 0 GPIO_ACTIVE_LOW>; - }; - broadband_blue: broadband-blue { - label = "bthomehubv3a:blue:broadband"; - gpios = <&gpio 12 GPIO_ACTIVE_LOW>; - }; - - power_red: power-red { - label = "bthomehubv3a:red:power"; - gpios = <&gpio 14 GPIO_ACTIVE_LOW>; - }; - power_orange: power-orange { - label = "bthomehubv3a:orange:power"; - gpios = <&gpio 5 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - power_blue: power-blue { - label = "bthomehubv3a:blue:power"; - gpios = <&gpio 1 GPIO_ACTIVE_LOW>; - }; - }; - - usb_vbus: regulator-usb-vbus { - compatible = "regulator-fixed"; - - regulator-name = "USB_VBUS"; - - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - gpio = <&gpio 33 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - nand_out { - lantiq,groups = "nand cle", "nand ale"; - lantiq,function = "ebu"; - lantiq,output = <1>; - lantiq,open-drain = <0>; - lantiq,pull = <0>; - }; - nand_cs1 { - lantiq,groups = "nand cs1"; - lantiq,function = "ebu"; - lantiq,open-drain = <0>; - lantiq,pull = <0>; - }; - - pci_in { - lantiq,groups = "req1"; - lantiq,function = "pci"; - lantiq,output = <0>; - lantiq,open-drain = <1>; - lantiq,pull = <2>; - }; - pci_out { - lantiq,groups = "gnt1"; - lantiq,function = "pci"; - lantiq,output = <1>; - lantiq,open-drain = <0>; - lantiq,pull = <0>; - }; - - pci_rst { - lantiq,pins = "io21"; - lantiq,output = <1>; - lantiq,open-drain = <0>; - }; - }; -}; - -&gsw { - phy-mode = "rgmii"; -}; - -&localbus { - nand@1 { /* NAND Flash: Samsung K9F5608U0D-JIB0 32MB */ - compatible = "lantiq,nand-xway"; - lantiq,cs = <1>; - bank-width = <2>; - reg = <1 0x0 0x2000000 >; - #address-cells = <1>; - #size-cells = <1>; - req-mask = <0x1>; /* PCI request lines to mask during NAND access */ - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "preboot"; - reg = <0x00000 0x8000>; - read-only; - }; - partition@8000 { - label = "u-boot"; - reg = <0x8000 0x05c000>; - read-only; - }; - partition@64000 { - label = "uboot_env"; - reg = <0x64000 0x004000>; - }; - ath9k_cal: partition@68000 { - label = "art-copy"; - reg = <0x68000 0x004000>; - }; - partition@6c000 { - label = "kernel"; - reg = <0x6c000 0x200000>; - }; - partition@26c000 { - label = "ubi"; - reg = <0x26c000 0x1d94000>; - }; - }; - }; -}; - -&pci0 { - status = "okay"; - gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; - - ath9k@7000 { - reg = <0x7000 0 0 0 0>; - qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:00:0e.0.bin */ - }; -}; - -&usb_phy0 { - status = "okay"; -}; - -&usb0 { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/BTHOMEHUBV5A.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/BTHOMEHUBV5A.dts deleted file mode 100644 index 166eec3419..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/BTHOMEHUBV5A.dts +++ /dev/null @@ -1,300 +0,0 @@ -/dts-v1/; - -#include "vr9.dtsi" - -#include -#include - -/ { - compatible = "bt,homehub-v5a", "lantiq,xway", "lantiq,vr9"; - model = "BT Home Hub 5A"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power_green; - led-failsafe = &power_red; - led-running = &power_blue; - led-upgrade = &power_blue; - - led-dsl = &broadband_blue; - led-wifi = &wireless_blue; - }; - - memory@0 { - reg = <0x0 0x8000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - reset { - label = "reset"; - gpios = <&gpio 2 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - wps { - label = "wps"; - gpios = <&gpio 25 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - restart { - label = "restart"; - gpios = <&gpio 39 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - - /* broadband-* is a single RGB led */ - broadband-red { - label = "bthomehubv5a:red:broadband"; - gpios = <&gpio 0 GPIO_ACTIVE_LOW>; - }; - broadband-green { - label = "bthomehubv5a:green:broadband"; - gpios = <&gpio 3 GPIO_ACTIVE_LOW>; - }; - broadband_blue: broadband-blue { - label = "bthomehubv5a:blue:broadband"; - gpios = <&gpio 8 GPIO_ACTIVE_LOW>; - }; - - /* wireless-* is a single RGB led */ - wireless-red { - label = "bthomehubv5a:red:wireless"; - gpios = <&gpio 9 GPIO_ACTIVE_LOW>; - }; - wireless-green { - label = "bthomehubv5a:green:wireless"; - gpios = <&gpio 10 GPIO_ACTIVE_LOW>; - }; - wireless_blue: wireless-blue { - label = "bthomehubv5a:blue:wireless"; - gpios = <&gpio 11 GPIO_ACTIVE_LOW>; - }; - - /* power-* is a single RGB led */ - power_red: power-red { - label = "bthomehubv5a:red:power"; - gpios = <&gpio 12 GPIO_ACTIVE_LOW>; - }; - power_green: power-green { - label = "bthomehubv5a:green:power"; - gpios = <&gpio 14 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - power_blue: power-blue { - label = "bthomehubv5a:blue:power"; - gpios = <&gpio 15 GPIO_ACTIVE_LOW>; - }; - - dimmed { - label = "dimmed"; - gpios = <&gpio 19 GPIO_ACTIVE_HIGH>; - }; - }; - - usb_vbus: regulator-usb-vbus { - compatible = "regulator-fixed"; - - regulator-name = "USB_VBUS"; - - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - gpio = <&gpio 33 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -ð0 { - lan: interface@0 { - compatible = "lantiq,xrx200-pdi"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - lantiq,switch; - - ethernet@0 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <0>; - phy-mode = "rgmii"; - phy-handle = <&phy0>; - }; - ethernet@1 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <1>; - phy-mode = "rgmii"; - phy-handle = <&phy1>; - }; - ethernet@2 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <2>; - phy-mode = "gmii"; - phy-handle = <&phy11>; - }; - ethernet@4 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <4>; - phy-mode = "gmii"; - phy-handle = <&phy13>; - }; - ethernet@5 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <5>; - phy-mode = "rgmii"; - phy-handle = <&phy5>; - }; - }; - - mdio@0 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "lantiq,xrx200-mdio"; - reg = <0>; - - phy0: ethernet-phy@0 { - reg = <0x0>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - phy1: ethernet-phy@1 { - reg = <0x1>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - phy5: ethernet-phy@5 { - reg = <0x5>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - phy11: ethernet-phy@11 { - reg = <0x11>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - phy13: ethernet-phy@13 { - reg = <0x13>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - }; -}; - -&gphy0 { - lantiq,gphy-mode = ; -}; - -&gphy1 { - lantiq,gphy-mode = ; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - mdio { - lantiq,groups = "mdio"; - lantiq,function = "mdio"; - }; - pci_rst { - lantiq,pins = "io21"; - lantiq,output = <1>; - lantiq,open-drain; - }; - pcie_rst { - lantiq,pins = "io38"; - lantiq,pull = <0>; - lantiq,output = <1>; - lantiq,open-drain; - }; - usb_vbus { - lantiq,pins = "io33"; - lantiq,pull = <0>; - lantiq,open-drain = <0>; - lantiq,output = <1>; - }; - nand_out { - lantiq,groups = "nand cle", "nand ale"; - lantiq,function = "ebu"; - lantiq,output = <1>; - lantiq,open-drain = <0>; - lantiq,pull = <0>; - }; - nand_cs1 { - lantiq,groups = "nand cs1"; - lantiq,function = "ebu"; - lantiq,open-drain = <0>; - lantiq,pull = <0>; - }; - }; -}; - -&localbus { - nand@1 { - compatible = "lantiq,nand-xway"; - lantiq,cs = <1>; - bank-width = <2>; - reg = <0x1 0x0 0x2000000>; - #address-cells = <1>; - #size-cells = <1>; - nand-on-flash-bbt; - nand-ecc-strength = <3>; - nand-ecc-step-size = <256>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "u-boot"; - reg = <0x0 0xa0000>; - read-only; - }; - partition@a0000 { - label = "uboot-env"; - reg = <0xa0000 0x20000>; - read-only; - }; - partition@c0000 { - label = "unused"; - reg = <0xc0000 0x40000>; - }; - partition@100000 { - label = "ubi"; - reg = <0x100000 0x7e80000>; - }; - /* - * last 512 KiB are for the bad block table, not writable - */ - }; - }; -}; - -&pci0 { - status = "okay"; - gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; - - wifi@168c,002d { - compatible = "pci168c,002d"; - reg = <0x7000 0 0 0 0>; - qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:00:0e.0.bin */ - qca,disable-5ghz; - }; -}; - -&usb_phy0 { - status = "okay"; -}; - -&usb0 { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/DGN1000B.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/DGN1000B.dts deleted file mode 100644 index 8c61e1b743..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/DGN1000B.dts +++ /dev/null @@ -1,174 +0,0 @@ -/dts-v1/; - -#include "amazonse.dtsi" - -#include - -/ { - compatible = "netgear,dgn1000b", "lantiq,xway", "lantiq,ase"; - model = "Netgear DGN1000B"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power; - led-failsafe = &power; - led-running = &power; - led-upgrade = &power; - - led-dsl = &dsl; - led-internet = &online_green; - }; - - memory@0 { - reg = <0x0 0x1000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - reset { - label = "reset"; - gpios = <&gpio 0 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - rfkill { - label = "rfkill"; - gpios = <&gpio 25 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - wps { - label = "wps"; - gpios = <&gpio 29 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - dsl: dsl { - label = "dgn1000b:green:dsl"; - gpios = <&gpio 1 GPIO_ACTIVE_LOW>; - default-state = "on"; - }; - online_green: online { - label = "dgn1000b:green:online"; - gpios = <&gpio 2 GPIO_ACTIVE_LOW>; - default-state = "on"; - }; - online2 { - label = "dgn1000b:red:online"; - gpios = <&gpio 3 GPIO_ACTIVE_LOW>; - default-state = "on"; - }; - wps { - label = "dgn1000b:green:wps"; - gpios = <&gpio 4 GPIO_ACTIVE_LOW>; - default-state = "on"; - }; - power: power { - label = "dgn1000b:green:power"; - gpios = <&gpio 13 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - /* - power red is missing - */ - }; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - asc { - lantiq,groups = "asc"; - lantiq,function = "asc"; - }; - keys_in { - lantiq,pins = "io0",/* "io25", */"io29"; - lantiq,pull = <2>; - lantiq,open-drain = <1>; - }; - }; - pins_spi_default: pins_spi_default { - spi_in { - lantiq,groups = "spi_di"; - lantiq,function = "spi"; - }; - spi_out { - lantiq,groups = "spi_do", "spi_clk", - "spi_cs1"; - lantiq,function = "spi"; - lantiq,output = <1>; - }; - }; -}; - -&gsw { - phy-mode = "mii"; - mac-address = [ 00 11 22 33 44 55 ]; -}; - -&spi { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&pins_spi_default>; - - m25p80@1 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "jedec,spi-nor"; - reg = <1 0>; - spi-max-frequency = <5000000>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - reg = <0x0 0x20000>; - label = "SPI (RO) U-Boot Image"; - read-only; - }; - - partition@20000 { - reg = <0x20000 0x10000>; - label = "ENV_MAC"; - read-only; - }; - - partition@30000 { - reg = <0x30000 0x10000>; - label = "DPF"; - read-only; - }; - - partition@40000 { - reg = <0x40000 0x10000>; - label = "NVRAM"; - read-only; - }; - - partition@500000 { - reg = <0x50000 0x003a0000>; - label = "kernel"; - }; - }; - }; -}; - -&usb_phy { - status = "okay"; -}; - -&usb { - status = "okay"; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/DGN3500.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/DGN3500.dts deleted file mode 100644 index 98a2ebd98e..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/DGN3500.dts +++ /dev/null @@ -1,8 +0,0 @@ -/dts-v1/; - -#include "DGN3500.dtsi" - -/ { - compatible = "netgear,dgn3500", "lantiq,xway", "lantiq,ar9"; - model = "Netgear DGN3500"; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/DGN3500.dtsi b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/DGN3500.dtsi deleted file mode 100644 index b0facb4107..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/DGN3500.dtsi +++ /dev/null @@ -1,214 +0,0 @@ -#include "ar9.dtsi" - -#include - -/ { - chosen { - bootargs = "root= console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power_green; - led-failsafe = &power_red; - led-running = &power_green; - led-upgrade = &power_green; - - led-dsl = &dsl; - led-internet = &internet; - led-usb = &led_usb; - led-wifi = &wifi_green; - }; - - memory@0 { - reg = <0x0 0x4000000>; - }; - - rtl8366rb { - compatible = "realtek,rtl8366rb"; - gpio-sda = <&gpio 35 GPIO_ACTIVE_HIGH>; - gpio-sck = <&gpio 37 GPIO_ACTIVE_HIGH>; - - realtek,initvals = < - 0x0000 0x0830 - 0x0400 0x8130 - 0x000A 0x83ED - 0x0F51 0x0017 - 0x02F5 0x0048 - 0x02FA 0xFFDF - 0x02FB 0xFFE0 - 0x0450 0x0000 - 0x0401 0x0000 - 0x0431 0x0960 - >; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - rfkill { - label = "rfkill"; - gpios = <&gpio 36 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - wps { - label = "wps"; - gpios = <&gpio 54 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - reset { - label = "reset"; - gpios = <&gpio 53 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - internet: internet { - label = "dgn3500:green:internet"; - gpios = <&gpio 2 GPIO_ACTIVE_LOW>; - }; - internet2 { - label = "dgn3500:red:internet"; - gpios = <&gpio 30 GPIO_ACTIVE_LOW>; - }; - dsl: dsl { - label = "dgn3500:green:dsl"; - gpios = <&gpio 4 GPIO_ACTIVE_LOW>; - }; - led_usb: usb { - label = "dgn3500:green:usb"; - gpios = <&gpio 22 GPIO_ACTIVE_LOW>; - }; - power_green: power { - label = "dgn3500:green:power"; - gpios = <&gpio 34 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - power_red: power2 { - label = "dgn3500:red:power"; - gpios = <&gpio 39 GPIO_ACTIVE_LOW>; - }; - wifi_green: wifi { - label = "dgn3500:green:wireless"; - gpios = <&gpio 14 GPIO_ACTIVE_LOW>; - }; - wifi2 { - label = "dgn3500:amber:wireless"; - gpios = <&gpio 51 GPIO_ACTIVE_LOW>; - }; - wps { - label = "dgn3500:green:wps"; - gpios = <&gpio 52 GPIO_ACTIVE_LOW>; - }; - }; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - exin { - lantiq,groups = "exin1"; - lantiq,function = "exin"; - }; - pci { - lantiq,groups = "gnt1", "req1"; - lantiq,function = "pci"; - }; - pci-in { - lantiq,groups = "req1"; - lantiq,output = <0>; - lantiq,open-drain = <1>; - lantiq,pull = <2>; - }; - pci-out { - lantiq,groups = "gnt1"; - lantiq,output = <1>; - lantiq,pull = <0>; - }; - }; - pins_spi_default: pins_spi_default { - spi_in { - lantiq,groups = "spi_di"; - lantiq,function = "spi"; - }; - spi_out { - lantiq,groups = "spi_do", "spi_clk", - "spi_cs4"; - lantiq,function = "spi"; - lantiq,output = <1>; - }; - }; -}; - -&gsw { - phy-mode = "mii"; -}; - -&pci0 { - status = "okay"; - gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; - - wifi@168c,0029 { - compatible = "pci168c,0029"; - reg = <0x7000 0 0 0 0>; - qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:00:0e.0.bin */ - }; -}; - -&spi { - status = "okay"; - - pinctrl-names = "default"; - pinctrl-0 = <&pins_spi_default>; - - m25p80@4 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "jedec,spi-nor"; - reg = <4 0>; - spi-max-frequency = <20000000>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - reg = <0x0 0x10000>; - label = "uboot"; - read-only; - }; - - partition@10000 { - reg = <0x10000 0x10000>; - label = "uboot-env"; - read-only; - }; - - ath9k_cal: partition@20000 { - reg = <0x20000 0x10000>; - label = "calibration"; - read-only; - }; - - partition@50000 { - reg = <0x50000 0xfa0000>; - label = "firmware"; - }; - }; - }; -}; - -&usb_phy0 { - status = "okay"; -}; - -&usb0 { - status = "okay"; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/DGN3500B.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/DGN3500B.dts deleted file mode 100644 index d1d788cc7d..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/DGN3500B.dts +++ /dev/null @@ -1,8 +0,0 @@ -/dts-v1/; - -#include "DGN3500.dtsi" - -/ { - compatible = "netgear,dgn3500b", "lantiq,xway", "lantiq,ar9"; - model = "Netgear DGN3500B"; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/DM200.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/DM200.dts deleted file mode 100644 index 8cf3456ee2..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/DM200.dts +++ /dev/null @@ -1,217 +0,0 @@ -/dts-v1/; - -#include "vr9.dtsi" - -#include -#include - -/ { - compatible = "netgear,dm200", "lantiq,xway", "lantiq,vr9"; - model = "Netgear DM200"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power_green; - led-failsafe = &power_amber; - led-running = &power_green; - led-upgrade = &power_green; - - led-dsl = &dsl_green; - }; - - memory@0 { - reg = <0x0 0x4000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - reset { - label = "reset"; - gpios = <&gpio 7 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio_export { - compatible = "gpio-export"; - #size-cells = <0>; - - annexa { - gpio-export,name = "annexa"; - gpio-export,output = <0>; - gpios = <&gpio 12 GPIO_ACTIVE_HIGH>; - }; - annexb { - gpio-export,name = "annexb"; - gpio-export,output = <0>; - gpios = <&gpio 15 GPIO_ACTIVE_HIGH>; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - - power_amber: power_amber { - label = "dm200:amber:power"; - gpios = <&gpio 0 GPIO_ACTIVE_HIGH>; - }; - power_green: power_green { - label = "dm200:green:power"; - gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; - }; - - lan_amber { - label = "dm200:amber:lan"; - gpios = <&gpio 33 GPIO_ACTIVE_HIGH>; - }; - lan_green { - label = "dm200:green:lan"; - gpios = <&gpio 11 GPIO_ACTIVE_HIGH>; - }; - - dsl_amber { - label = "dm200:amber:dsl"; - gpios = <&gpio 8 GPIO_ACTIVE_HIGH>; - }; - dsl_green: dsl_green { - label = "dm200:green:dsl"; - gpios = <&gpio 36 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -ð0 { - lantiq,phys = <&gphy1>; - - lan: interface@0 { - compatible = "lantiq,xrx200-pdi"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - - ethernet@4 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <4>; - phy-mode = "mii"; - phy-handle = <&phy13>; - }; - }; - - mdio@0 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "lantiq,xrx200-mdio"; - reg = <0>; - - phy13: ethernet-phy@13 { - reg = <0x13>; - compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; - }; - }; -}; - -&gphy1 { - lantiq,gphy-mode = ; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - mdio { - lantiq,groups = "mdio"; - lantiq,function = "mdio"; - }; - }; - - pins_spi_default: pins_spi_default { - spi_in { - lantiq,groups = "spi_di"; - lantiq,function = "spi"; - }; - spi_out { - lantiq,groups = "spi_do", "spi_clk", "spi_cs4"; - lantiq,function = "spi"; - lantiq,output = <1>; - }; - }; -}; - -&pcie0 { - status = "disabled"; -}; - -&spi { - status = "okay"; - - pinctrl-names = "default"; - pinctrl-0 = <&pins_spi_default>; - - m25p80@4 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "jedec,spi-nor"; - reg = <4 0>; - spi-max-frequency = <10000000>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - reg = <0x0 0x20000>; - label = "uboot"; - read-only; - }; - - partition@20000 { - reg = <0x20000 0x10000>; - label = "gphyfirmware"; - read-only; - }; - - partition@30000 { - reg = <0x30000 0x7b0000>; - label = "firmware"; - }; - - partition@7e0000 { - reg = <0x7e0000 0x10000>; - label = "sysconfig"; - read-only; - }; - - partition@7f0000 { - reg = <0x7f0000 0x2000>; - label = "ubootconfig"; - read-only; - }; - - partition@7f2000 { - reg = <0x7f2000 0x1000>; - label = "ART"; - read-only; - }; - - partition@7f3000 { - reg = <0x7f3000 0x1000>; - label = "pot"; - read-only; - }; - - partition@7f4000 { - reg = <0x7f4000 0xc000>; - label = "ret"; - read-only; - }; - }; - }; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY50712.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY50712.dts deleted file mode 100644 index ec287ab40b..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY50712.dts +++ /dev/null @@ -1,81 +0,0 @@ -/dts-v1/; - -#include "danube.dtsi" - -/ { - compatible = "lantiq,easy50712", "lantiq,xway", "lantiq,danube"; - model = "Intel EASY50712 Nand"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - memory@0 { - reg = <0x0 0x2000000>; - }; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - stp { - lantiq,groups = "stp"; - lantiq,function = "stp"; - }; - exin { - lantiq,groups = "exin1"; - lantiq,function = "exin"; - }; - pci { - lantiq,groups = "gnt1"; - lantiq,function = "pci"; - }; - conf_out { - lantiq,pins = "io4", "io5", "io6"; /* stp */ - lantiq,open-drain; - lantiq,pull = <0>; - }; - }; -}; - -&gsw { - phy-mode = "rmii"; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x2000000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x00000 0x10000>; /* 64 KB */ - }; - - partition@10000 { - label = "uboot_env"; - reg = <0x10000 0x10000>; /* 64 KB */ - }; - - partition@20000 { - label = "firmware"; - reg = <0x20000 0x3d0000>; - }; - - partition@400000 { - label = "rootfs"; - reg = <0x400000 0x400000>; - }; - }; - }; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY50810.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY50810.dts deleted file mode 100644 index 21562dce21..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY50810.dts +++ /dev/null @@ -1,87 +0,0 @@ -/dts-v1/; - -#include "ar9.dtsi" - -/ { - compatible = "lantiq,easy50810", "lantiq,xway", "lantiq,ar9"; - model = "Lantiq EASY50810"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - memory@0 { - reg = <0x0 0x2000000>; - }; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - stp { - lantiq,groups = "stp"; - lantiq,function = "stp"; - }; - exin { - lantiq,groups = "exin1"; - lantiq,function = "exin"; - }; - pci { - lantiq,groups = "gnt1"; - lantiq,function = "pci"; - }; - conf_out { - lantiq,pins = "io4", "io5", "io6"; /* stp */ - lantiq,open-drain; - lantiq,pull = <0>; - }; - }; -}; - -&gsw { - phy-mode = "rmii"; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x2000000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x00000 0x10000>; /* 64 KB */ - }; - - partition@10000 { - label = "uboot_env"; - reg = <0x10000 0x10000>; /* 64 KB */ - }; - - partition@20000 { - label = "firmware"; - reg = <0x20000 0x3d0000>; - }; - - partition@400000 { - label = "rootfs"; - reg = <0x400000 0x400000>; - }; - }; - }; -}; - -&stp { - status = "okay"; - lantiq,shadow = <0xfff>; - lantiq,groups = <0x3>; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY80920.dtsi b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY80920.dtsi deleted file mode 100644 index 781cdfdb5b..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY80920.dtsi +++ /dev/null @@ -1,313 +0,0 @@ -#include "vr9.dtsi" - -#include -#include - -/ { - compatible = "lantiq,easy80920", "lantiq,xway", "lantiq,vr9"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power; - led-failsafe = &power; - led-running = &power; - led-upgrade = &power; - - led-usb = &led_usb1; - led-usb2 = &led_usb2; - }; - - memory@0 { - reg = <0x0 0x4000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; -/* reset { - label = "reset"; - gpios = <&gpio 7 GPIO_ACTIVE_LOW>; - linux,code = ; - };*/ - paging { - label = "paging"; - gpios = <&gpio 11 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - - power: power { - label = "easy80920:green:power"; - gpios = <&stp 9 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - warning { - label = "easy80920:green:warning"; - gpios = <&stp 22 GPIO_ACTIVE_HIGH>; - }; - fxs1 { - label = "easy80920:green:fxs1"; - gpios = <&stp 21 GPIO_ACTIVE_HIGH>; - }; - fxs2 { - label = "easy80920:green:fxs2"; - gpios = <&stp 20 GPIO_ACTIVE_HIGH>; - }; - fxo { - label = "easy80920:green:fxo"; - gpios = <&stp 19 GPIO_ACTIVE_HIGH>; - }; - led_usb1: usb1 { - label = "easy80920:green:usb1"; - gpios = <&stp 18 GPIO_ACTIVE_HIGH>; - }; - led_usb2: usb2 { - label = "easy80920:green:usb2"; - gpios = <&stp 15 GPIO_ACTIVE_HIGH>; - }; - sd { - label = "easy80920:green:sd"; - gpios = <&stp 14 GPIO_ACTIVE_HIGH>; - }; - wps { - label = "easy80920:green:wps"; - gpios = <&stp 12 GPIO_ACTIVE_HIGH>; - }; - }; - - usb_vbus: regulator-usb-vbus { - compatible = "regulator-fixed"; - - regulator-name = "USB_VBUS"; - - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - gpio = <&gpio 33 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -ð0 { - lan: interface@0 { - compatible = "lantiq,xrx200-pdi"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - lantiq,switch; - - ethernet@4 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <4>; - phy-mode = "gmii"; - phy-handle = <&phy13>; - }; - ethernet@2 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <2>; - phy-mode = "gmii"; - phy-handle = <&phy11>; - }; - ethernet@1 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <1>; - phy-mode = "rgmii"; - phy-handle = <&phy1>; - }; - ethernet@0 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <0>; - phy-mode = "rgmii"; - phy-handle = <&phy0>; - }; - }; - - wan: interface@1 { - compatible = "lantiq,xrx200-pdi"; - #address-cells = <1>; - #size-cells = <0>; - reg = <1>; - lantiq,wan; - - ethernet@5 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <5>; - phy-mode = "rgmii"; - phy-handle = <&phy5>; - }; - }; - - mdio@0 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "lantiq,xrx200-mdio"; - reg = <0>; - - phy0: ethernet-phy@0 { - reg = <0x0>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - phy1: ethernet-phy@1 { - reg = <0x1>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - phy5: ethernet-phy@5 { - reg = <0x5>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - phy11: ethernet-phy@11 { - reg = <0x11>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - phy13: ethernet-phy@13 { - reg = <0x13>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - }; -}; - -&gphy0 { - lantiq,gphy-mode = ; -}; - -&gphy1 { - lantiq,gphy-mode = ; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - exin3 { - lantiq,groups = "exin3"; - lantiq,function = "exin"; - }; - stp { - lantiq,groups = "stp"; - lantiq,function = "stp"; - }; - nand { - lantiq,groups = "nand cle", "nand ale", - "nand rd", "nand rdy"; - lantiq,function = "ebu"; - }; - mdio { - lantiq,groups = "mdio"; - lantiq,function = "mdio"; - }; - pci { - lantiq,groups = "gnt1", "req1"; - lantiq,function = "pci"; - }; - conf_out { - lantiq,pins = "io24", "io13", "io49", /* nand cle, ale and rd */ - "io4", "io5", "io6", /* stp */ - "io21", - "io33"; - lantiq,open-drain; - lantiq,pull = <0>; - lantiq,output = <1>; - }; - pcie-rst { - lantiq,pins = "io38"; - lantiq,pull = <0>; - lantiq,output = <1>; - }; - conf_in { - lantiq,pins = "io39", /* exin3 */ - "io48"; /* nand rdy */ - lantiq,pull = <2>; - }; - }; - pins_spi_default: pins_spi_default { - spi_in { - lantiq,groups = "spi_di"; - lantiq,function = "spi"; - }; - spi_out { - lantiq,groups = "spi_do", "spi_clk", - "spi_cs4"; - lantiq,function = "spi"; - lantiq,output = <1>; - }; - }; -}; - -&spi { - pinctrl-names = "default"; - pinctrl-0 = <&pins_spi_default>; - - status = "okay"; - - m25p80@4 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "jedec,spi-nor"; - reg = <4 0>; - spi-max-frequency = <1000000>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - reg = <0x0 0x20000>; - label = "SPI (RO) U-Boot Image"; - read-only; - }; - - partition@20000 { - reg = <0x20000 0x10000>; - label = "ENV_MAC"; - read-only; - }; - - partition@30000 { - reg = <0x30000 0x10000>; - label = "DPF"; - read-only; - }; - - partition@40000 { - reg = <0x40000 0x10000>; - label = "NVRAM"; - read-only; - }; - - partition@500000 { - reg = <0x50000 0x003a0000>; - label = "kernel"; - }; - }; - }; -}; - -&stp { - status = "okay"; - - lantiq,shadow = <0xffff>; - lantiq,groups = <0x7>; - lantiq,dsl = <0x3>; - lantiq,phy1 = <0x7>; - lantiq,phy2 = <0x7>; - /* lantiq,rising; */ -}; - -&usb_phy0 { - status = "okay"; -}; - -&usb0 { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY80920NAND.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY80920NAND.dts deleted file mode 100644 index 0134a7c177..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY80920NAND.dts +++ /dev/null @@ -1,65 +0,0 @@ -/dts-v1/; - - -#include "EASY80920.dtsi" - -/ { - compatible = "lantiq,easy80920-nand", "lantiq,easy80920", "lantiq,xway", "lantiq,vr9"; - model = "Intel EASY80920 Nand"; - - chosen { - bootargs = "ubi.mtd=ubi ubi.block=0,rootfsA root=/dev/ubiblock0_1"; - }; -}; - -&localbus { - nand@0 { - compatible = "lantiq,nand-xway"; - lantiq,cs = <1>; - bank-width = <2>; - reg = <0 0x0 0x2000000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x00000 0x100000>; /* 1024 KB */ - }; - - partition@100000 { - label = "uboot_env"; - reg = <0x100000 0x40000>; /* 256 KB */ - }; - - partition@140000 { - label = "ubootconfigB"; - reg = <0x140000 0x40000>; /* 256 KB */ - }; - - partition@180000 { - label = "gphyfirmware"; - reg = <0x180000 0x40000>; /* 256 KB */ - }; - - partition@1c0000 { - label = "ubi"; - reg = <0x1c0000 0xc800000>; - }; - - partition@c9c0000 { - label = "calibration"; - reg = <0xc9c0000 0x100000>; - }; - - partition@cac0000 { - label = "res"; - reg = <0xcac0000 0x13540000>; - }; - }; - }; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY80920NOR.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY80920NOR.dts deleted file mode 100644 index 9adc0b4f92..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY80920NOR.dts +++ /dev/null @@ -1,39 +0,0 @@ -/dts-v1/; - -#include "EASY80920.dtsi" - -/ { - compatible = "lantiq,easy80920-nor", "lantiq,easy80920", "lantiq,xway", "lantiq,vr9"; - model = "Intel EASY80920 Nor"; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x2000000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x00000 0x10000>; - }; - - partition@10000 { - label = "uboot_env"; - reg = <0x10000 0x10000>; - }; - - partition@20000 { - label = "firmware"; - reg = <0x20000 0x7e0000>; - }; - }; - }; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY88388.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY88388.dts deleted file mode 100644 index 86f3b47c6b..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY88388.dts +++ /dev/null @@ -1,93 +0,0 @@ -/dts-v1/; - -#include -#include "falcon.dtsi" -#include "falcon-sflash-16M.dtsi" - -/ { - model = "Lantiq Falcon FTTDP8 Reference Board"; - compatible = "lantiq,easy88388", "lantiq,falcon"; - - aliases { - spi0 = &ebu_cs0; - }; - - memory@0 { - device_type = "memory"; - reg = <0x0 0x4000000>; // 64M at 0x0 - }; - - gpio-keys { - compatible = "gpio-keys"; - reset { - label = "reset"; - gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; - linux,code = <0x198>; - }; - }; - - pinctrl { - led_pins: led-pins { - lantiq,pins = "io34", "io35", "io36", "io37", "io38", - "io39", "io40", "io41"; - lantiq,function = "gpio"; - }; - }; - - easy88388-leds { - compatible = "gpio-leds"; - pinctrl-names = "default"; - pinctrl-0 = <&led_pins &bootled_pins>; - - GPON { - label = "easy88388:green:gpon"; - gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; - }; - TEST { - label = "easy88388:green:test"; - gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; - }; - STATUS { - label = "easy88388:green:status"; - gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; - }; - ERROR { - label = "easy88388:red:error"; - gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; - }; - - DSL1 { - label = "easy88388:dsl:1"; - gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; - }; - DSL2 { - label = "easy88388:dsl:2"; - gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; - }; - DSL3 { - label = "easy88388:dsl:3"; - gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; - }; - DSL4 { - label = "easy88388:dsl:4"; - gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; - }; - DSL5 { - label = "easy88388:dsl:5"; - gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>; - }; - DSL6 { - label = "easy88388:dsl:6"; - gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; - }; - DSL7 { - label = "easy88388:dsl:7"; - gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; - }; - DSL8 { - label = "easy88388:dsl:8"; - gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; - }; - }; -}; - diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY88444.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY88444.dts deleted file mode 100644 index e1a934fc47..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY88444.dts +++ /dev/null @@ -1,72 +0,0 @@ -/dts-v1/; - -#include -#include "falcon.dtsi" -#include "falcon-sflash-16M.dtsi" - -/ { - model = "Lantiq Falcon FTTdp G.FAST Reference Board"; - compatible = "lantiq,easy88444", "lantiq,falcon"; - - aliases { - spi0 = &ebu_cs0; - }; - - memory@0 { - device_type = "memory"; - reg = <0x0 0x4000000>; // 64M at 0x0 - }; - - gpio-keys { - compatible = "gpio-keys"; - reset { - label = "reset"; - gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; - linux,code = <0x198>; - }; - }; - - pinctrl { - led_pins: led-pins { - lantiq,pins = "io34", "io35", "io37"; - lantiq,function = "gpio"; - }; - }; - - easy88444-leds { - compatible = "gpio-leds"; - pinctrl-names = "default"; - pinctrl-0 = <&led_pins &bootled_pins>; - - GPON { - label = "easy88444:green:gpon"; - gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; - }; - TEST { - label = "easy88444:green:test"; - gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; - }; - STATUS { - label = "easy88444:green:status"; - gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; - }; - - GFAST1 { - label = "easy88444:gfast:1"; - gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; - }; - GFAST2 { - label = "easy88444:gfast:2"; - gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; - }; - GFAST3 { - label = "easy88444:gfast:3"; - gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; - }; - GFAST4 { - label = "easy88444:gfast:4"; - gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; - }; - }; -}; - diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY98000-base.dtsi b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY98000-base.dtsi deleted file mode 100644 index cfe1140ac1..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY98000-base.dtsi +++ /dev/null @@ -1,110 +0,0 @@ - -#include -#include - -/ { - compatible = "lantiq,easy98000", "lantiq,falcon"; - - memory@0 { - device_type = "memory"; - reg = <0x0 0x4000000>; - }; - - easy98000-leds { - compatible = "gpio-leds"; - pinctrl-names = "default"; - pinctrl-0 = <&bootled_pins>; - - LED_0 { - label = "easy98000:green:gpon"; - gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - LED_1 { - label = "easy98000:red:gpon"; - gpios = <&gpio0 10 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - LED_2 { - label = "easy98000:green:gpon_tx"; - gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - LED_3 { - label = "easy98000:green:gpon_rx"; - gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - LED_4 { - label = "easy98000:green:voice"; - gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - LED_5 { - label = "easy98000:green:status"; - gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - }; -}; - -&ebu_cs1 { - eth0: ethernet@0000000 { - compatible = "davicom,dm9000"; - device_type = "network"; - reg = <0x0000003 0x1>, <0x0000001 0x1>; - reg-names = "addr", "data"; - interrupt-parent = <&gpio1>; - #interrupt-cells = <2>; - interrupts = <10 IRQ_TYPE_LEVEL_LOW>; - local-mac-address = [ 00 00 00 00 00 00 ]; - }; - - cpld@3c00000 { - compatible = "lantiq,easy98000_addon"; - reg = <0x3c00000 0x2>; - }; - - cpld@3c0000c { - compatible = "lantiq,easy98000_cpld_led"; - reg = <0x3c0000c 0x2>, <0x3c00012 0x2>; - }; -}; - -/* // enable this for second uart: -&serial1 { - status = "okay"; -};*/ - -&spi { - status = "okay"; - - eeprom@1 { - compatible = "atmel,at25", "atmel,at25160n"; - reg = <2>; - spi-max-frequency = <1000000>; - spi-cpha; - spi-cpol; - - pagesize = <32>; - size = <2048>; - address-width = <16>; - }; -}; - -&i2c { - status = "okay"; - - clock-frequency = <100000>; - - /* eeprom-emulation by OMU */ - eeprom@50 { - compatible = "at,24c02"; - reg = <0x50>; - }; - eeprom@51 { - compatible = "at,24c02"; - reg = <0x51>; - }; -}; - diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY98000NAND.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY98000NAND.dts deleted file mode 100644 index a40cef3931..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY98000NAND.dts +++ /dev/null @@ -1,40 +0,0 @@ -/dts-v1/; - -#include "falcon.dtsi" -#include "EASY98000-base.dtsi" - -/ { - model = "Lantiq Falcon (NAND)"; - compatible = "lantiq,easy98000-nand", "lantiq,easy98000", "lantiq,falcon"; - - aliases { - spi0 = &spi; - }; -}; - -&ebu_cs0 { - gen_nand@0 { - compatible = "gen_nand", "lantiq,nand-falcon"; - bank-width = <1>; - reg = <0x0 0x40000>; - #address-cells = <1>; - #size-cells = <1>; - linux,mtd-name = "gen_nand"; - bbt-use-flash; - - partition@0 { - label = "uboot"; - reg = <0x00000 0x40000>; - }; - - partition@10000 { - label = "uboot_env"; - reg = <0x40000 0x40000>; - }; - - partition@20000 { - label = "linux"; - reg = <0x80000 0x3d0000>; - }; - }; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY98000NOR.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY98000NOR.dts deleted file mode 100644 index ad53bf96e9..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY98000NOR.dts +++ /dev/null @@ -1,38 +0,0 @@ -/dts-v1/; - -#include "falcon.dtsi" -#include "EASY98000-base.dtsi" - -/ { - model = "Lantiq Falcon (NOR)"; - compatible = "lantiq,easy98000-nor", "lantiq,easy98000", "lantiq,falcon"; - - aliases { - spi0 = &spi; - }; -}; - -&ebu_cs0 { - cfi@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0x0 0x4000000>; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x00000 0x40000>; - }; - - partition@10000 { - label = "uboot_env"; - reg = <0x40000 0x40000>; - }; - - partition@20000 { - label = "linux"; - reg = <0x80000 0x3d0000>; - }; - }; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY98000SFLASH.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY98000SFLASH.dts deleted file mode 100644 index bbe524e94e..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY98000SFLASH.dts +++ /dev/null @@ -1,16 +0,0 @@ -/dts-v1/; - -#include "falcon.dtsi" -#include "EASY98000-base.dtsi" -#include "falcon-sflash-16M.dtsi" - -/ { - model = "Lantiq Falcon (SFLASH)"; - compatible = "lantiq,easy98000-sflash", "lantiq,easy98000", "lantiq,falcon"; - - aliases { - spi0 = &ebu_cs0; - spi1 = &spi; - }; -}; - diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY98020.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY98020.dts deleted file mode 100644 index b66786a2ce..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY98020.dts +++ /dev/null @@ -1,91 +0,0 @@ -/dts-v1/; - -#include - -#include "falcon.dtsi" -#include "falcon-sflash-16M.dtsi" - -/ { - model = "Lantiq Falcon Reference Board"; - compatible = "lantiq,easy98020", "lantiq,falcon"; - - aliases { - spi0 = &ebu_cs0; - }; - - memory@0 { - device_type = "memory"; - reg = <0x0 0x4000000>; // 64M at 0x0 - }; - - gpio-keys { - compatible = "gpio-keys"; - reset { - label = "reset"; - gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; - linux,code = <0x198>; - }; - }; - - pinctrl { - led_pins: phy-led-pins { - lantiq,pins = "io42", "io41", "io38", "io37"; - lantiq,function = "gpio"; - }; - }; - - easy98020-leds { - compatible = "gpio-leds"; - pinctrl-names = "default"; - pinctrl-0 = <&bootled_pins>; - - GPON { - label = "easy98020:green:gpon"; - gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - TEST { - label = "easy98020:green:test"; - gpios = <&gpio0 10 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - ETH { - label = "easy98020:green:status"; - gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - VOICE { - label = "easy98020:green:voice"; - gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - VIDEO { - label = "easy98020:green:video"; - gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - }; - - easy98020-phy-leds { - compatible = "gpio-leds"; - pinctrl-names = "default"; - pinctrl-0 = <&led_pins>; - - GE0_ACT { - label = "easy98020:ge0_act"; - gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; - }; - GE0_LINK { - label = "easy98020:ge0_link"; - gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; - }; - GE1_ACT { - label = "easy98020:ge1_act"; - gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; - }; - GE1_LINK { - label = "easy98020:ge1_link"; - gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; - }; - }; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY98020V18.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY98020V18.dts deleted file mode 100644 index 9aa1be91ed..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY98020V18.dts +++ /dev/null @@ -1,68 +0,0 @@ -/dts-v1/; - -#include - -#include "falcon.dtsi" -#include "falcon-sflash-16M.dtsi" - -/ { - model = "Lantiq Falcon Reference Board V1.8"; - compatible = "lantiq,easy98020-v18", "lantiq,easy98020", "lantiq,falcon"; - - aliases { - spi0 = &ebu_cs0; - }; - - memory@0 { - device_type = "memory"; - reg = <0x0 0x4000000>; // 64M at 0x0 - }; - - gpio-keys { - compatible = "gpio-keys"; - reset { - label = "reset"; - gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; - linux,code = <0x198>; - }; - }; - - pinctrl { - led_pins: led-pins { - lantiq,pins = "io11", "io14", "io36", "io37", "io38"; - lantiq,function = "gpio"; - }; - }; - - easy98020-leds { - compatible = "gpio-leds"; - pinctrl-names = "default"; - pinctrl-0 = <&led_pins &bootled_pins>; - - GPON { - label = "easy98020:green:gpon"; - gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - TEST { - label = "easy98020:green:test"; - gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - ETH { - label = "easy98020:green:status"; - gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - VOICE { - label = "easy98020:green:voice"; - gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - VIDEO { - label = "easy98020:green:video"; - gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - }; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY98021.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY98021.dts deleted file mode 100644 index 38154d6f1c..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY98021.dts +++ /dev/null @@ -1,81 +0,0 @@ -/dts-v1/; - -#include - -#include "falcon.dtsi" -#include "falcon-sflash-16M.dtsi" - -/ { - model = "Lantiq Falcon HGU Reference Board"; - compatible = "lantiq,easy98021", "lantiq,easy98020", "lantiq,falcon"; - - aliases { - spi0 = &ebu_cs0; - }; - - memory@0 { - device_type = "memory"; - reg = <0x0 0x4000000>; // 64M at 0x0 - }; - - gpio-keys { - compatible = "gpio-keys"; - reset { - label = "reset"; - gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; - linux,code = <0x198>; - }; - }; - - gpio-mmc { - /* Place-holder for SIM-Card connector, - to list the used GPIOs, no official binding */ - compatible = "gpio-mmc"; - gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>, - <&gpio0 3 GPIO_ACTIVE_HIGH>, - <&gpio0 2 GPIO_ACTIVE_HIGH>, - <0>; /* no CS */ - gpio-names = "di", "do", "clk", "cs"; - reset-gpio = <&gpio3 24 GPIO_ACTIVE_HIGH>; - }; - - pinctrl { - led_pins: led-pins { - lantiq,pins = "io11", "io14", "io36", "io37", "io38"; - lantiq,function = "gpio"; - }; - }; - - easy98021-leds { - compatible = "gpio-leds"; - pinctrl-names = "default"; - pinctrl-0 = <&led_pins &bootled_pins>; - - GPON { - label = "easy98021:green:gpon"; - gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - TEST { - label = "easy98021:red:test"; - gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - ETH { - label = "easy98021:green:status"; - gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - VOICE { - label = "easy98021:green:voice"; - gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - SIMCARD { - label = "easy98021:green:simcard"; - gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - }; -}; - diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY98035SYNCE.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY98035SYNCE.dts deleted file mode 100644 index df941cdb67..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY98035SYNCE.dts +++ /dev/null @@ -1,76 +0,0 @@ -/dts-v1/; - -#include "falcon.dtsi" -#include "falcon-sflash-16M.dtsi" - -/ { - model = "Lantiq Falcon SFP Stick with SyncE"; - compatible = "lantiq,easy98035synce", "lantiq,falcon-sfp", "lantiq,falcon"; - - aliases { - spi0 = &ebu_cs0; - }; - - memory@0 { - device_type = "memory"; - reg = <0x0 0x4000000>; // 64M at 0x0 - }; - - pinctrl { - compatible = "lantiq,pinctrl-falcon"; - - asc0_func1: func1 { - func1_tx { - lantiq,pins = "io32"; - lantiq,mux = <1>; - lantiq,input = <0>; - }; - func1_rx { - lantiq,pins = "io33"; - lantiq,mux = <0>; - }; - }; - asc0_func2: func2 { - func2_tx { - lantiq,pins = "io32"; - lantiq,mux = <0>; - }; - func2_rx { - lantiq,pins = "io33"; - lantiq,mux = <1>; - lantiq,input = <0>; - }; - }; - asc0_func3: func3 { - func3_tx { - lantiq,pins = "io32"; - lantiq,mux = <1>; - lantiq,input = <0>; - }; - func3_rx { - lantiq,pins = "io33"; - lantiq,mux = <1>; - lantiq,input = <0>; - }; - }; - }; - - pinselect-asc0 { - compatible = "lantiq,pinselect-asc0"; - pinctrl-names = "asc0", "func1", "func2", "func3"; - pinctrl-0 = <&asc0_pins>; - pinctrl-1 = <&asc0_func1>; - pinctrl-2 = <&asc0_func2>; - pinctrl-3 = <&asc0_func3>; - }; -}; - -&serial0 { - pinctrl-names = "default"; - /* use "empty" pinctrl to leave setting from u-boot enabled */ - pinctrl-0 = < >; -}; - -&i2c { - status = "okay"; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY98035SYNCE1588.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY98035SYNCE1588.dts deleted file mode 100644 index a3abc6e707..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/EASY98035SYNCE1588.dts +++ /dev/null @@ -1,76 +0,0 @@ -/dts-v1/; - -#include "falcon.dtsi" -#include "falcon-sflash-16M.dtsi" - -/ { - model = "Lantiq Falcon SFP Stick with SyncE/1588"; - compatible = "lantiq,easy98035synce1588", "lantiq,falcon-sfp", "lantiq,falcon"; - - aliases { - spi0 = &ebu_cs0; - }; - - memory@0 { - device_type = "memory"; - reg = <0x0 0x4000000>; // 64M at 0x0 - }; - - pinctrl { - compatible = "lantiq,pinctrl-falcon"; - - asc0_func1: func1 { - func1_tx { - lantiq,pins = "io32"; - lantiq,mux = <1>; - lantiq,input = <0>; - }; - func1_rx { - lantiq,pins = "io33"; - lantiq,mux = <0>; - }; - }; - asc0_func2: func2 { - func2_tx { - lantiq,pins = "io32"; - lantiq,mux = <0>; - }; - func2_rx { - lantiq,pins = "io33"; - lantiq,mux = <1>; - lantiq,input = <0>; - }; - }; - asc0_func3: func3 { - func3_tx { - lantiq,pins = "io32"; - lantiq,mux = <1>; - lantiq,input = <0>; - }; - func3_rx { - lantiq,pins = "io33"; - lantiq,mux = <1>; - lantiq,input = <0>; - }; - }; - }; - - pinselect-asc0 { - compatible = "lantiq,pinselect-asc0"; - pinctrl-names = "asc0", "func1", "func2", "func3"; - pinctrl-0 = <&asc0_pins>; - pinctrl-1 = <&asc0_func1>; - pinctrl-2 = <&asc0_func2>; - pinctrl-3 = <&asc0_func3>; - }; -}; - -&serial0 { - pinctrl-names = "default"; - /* use "empty" pinctrl to leave setting from u-boot enabled */ - pinctrl-0 = < >; -}; - -&i2c { - status = "okay"; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FALCON-MDU.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FALCON-MDU.dts deleted file mode 100644 index 6710bbe98e..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FALCON-MDU.dts +++ /dev/null @@ -1,53 +0,0 @@ -/dts-v1/; - -#include - -#include "falcon.dtsi" -#include "falcon-sflash-16M.dtsi" - -/ { - model = "Lantiq Falcon / Vinax MDU Board"; - compatible = "lantiq,falcon-mdu", "lantiq,falcon"; - - aliases { - spi0 = &ebu_cs0; - }; - - memory@0 { - device_type = "memory"; - reg = <0x0 0x4000000>; // 64M at 0x0 - }; - - mdu-leds { - compatible = "gpio-leds"; - pinctrl-names = "default"; - pinctrl-0 = <&bootled_pins>; - - LED_0 { - label = "mdu:green:gpon"; - gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - LED_1 { - label = "mdu:green:status"; - gpios = <&gpio0 10 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - LED_2 { - label = "mdu:green:2"; - gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - LED_3 { - label = "mdu:green:3"; - gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - LED_4 { - label = "mdu:green:4"; - gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; - default-state = "keep"; - }; - }; -}; - diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FALCON-SFP.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FALCON-SFP.dts deleted file mode 100644 index 8d45de4ebe..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FALCON-SFP.dts +++ /dev/null @@ -1,76 +0,0 @@ -/dts-v1/; - -#include "falcon.dtsi" -#include "falcon-sflash-16M.dtsi" - -/ { - model = "Lantiq Falcon SFP Stick"; - compatible = "lantiq,falcon-sfp", "lantiq,falcon"; - - aliases { - spi0 = &ebu_cs0; - }; - - memory@0 { - device_type = "memory"; - reg = <0x0 0x4000000>; // 64M at 0x0 - }; - - pinctrl { - compatible = "lantiq,pinctrl-falcon"; - - asc0_func1: func1 { - func1_tx { - lantiq,pins = "io32"; - lantiq,mux = <1>; - lantiq,output = <0>; - }; - func1_rx { - lantiq,pins = "io33"; - lantiq,mux = <0>; - }; - }; - asc0_func2: func2 { - func2_tx { - lantiq,pins = "io32"; - lantiq,mux = <0>; - }; - func2_rx { - lantiq,pins = "io33"; - lantiq,mux = <1>; - lantiq,input = <0>; - }; - }; - asc0_func3: func3 { - func3_tx { - lantiq,pins = "io32"; - lantiq,mux = <1>; - lantiq,output = <0>; - }; - func3_rx { - lantiq,pins = "io33"; - lantiq,mux = <1>; - lantiq,input = <0>; - }; - }; - }; - - pinselect-asc0 { - compatible = "lantiq,pinselect-asc0"; - pinctrl-names = "asc0", "func1", "func2", "func3"; - pinctrl-0 = <&asc0_pins>; - pinctrl-1 = <&asc0_func1>; - pinctrl-2 = <&asc0_func2>; - pinctrl-3 = <&asc0_func3>; - }; -}; - -&serial0 { - pinctrl-names = "default"; - /* use "empty" pinctrl to leave setting from u-boot enabled */ - pinctrl-0 = < >; -}; - -&i2c { - status = "okay"; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ3370-REV2-HYNIX.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ3370-REV2-HYNIX.dts deleted file mode 100644 index ebd6f6e4c8..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ3370-REV2-HYNIX.dts +++ /dev/null @@ -1,38 +0,0 @@ -/dts-v1/; - -#include "FRITZ3370-REV2.dtsi" - -/ { - compatible = "avm,fritz3370-rev2-hynix", "avm,fritz3370-rev2", "lantiq,xway", "lantiq,vr9"; - model = "AVM FRITZ!Box 3370 Rev. 2 (Hynix NAND)"; -}; - -&localbus { - nand@1 { - compatible = "lantiq,nand-xway"; - bank-width = <2>; - reg = <1 0x0 0x2000000>; - #address-cells = <1>; - #size-cells = <1>; - - nand-ecc-mode = "soft"; - nand-ecc-strength = <3>; - nand-ecc-step-size = <256>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "kernel"; - reg = <0x0 0x400000>; - }; - - partition@400000 { - label = "ubi"; - reg = <0x400000 0x7c00000>; - }; - }; - }; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ3370-REV2-MICRON.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ3370-REV2-MICRON.dts deleted file mode 100644 index dcc97d2808..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ3370-REV2-MICRON.dts +++ /dev/null @@ -1,36 +0,0 @@ -/dts-v1/; - -#include "FRITZ3370-REV2.dtsi" - -/ { - compatible = "avm,fritz3370-rev2-micron", "avm,fritz3370-rev2", "lantiq,xway", "lantiq,vr9"; - model = "AVM FRITZ!Box 3370 Rev. 2 (Micron NAND)"; -}; - -&localbus { - nand@1 { - compatible = "lantiq,nand-xway"; - bank-width = <2>; - reg = <1 0x0 0x2000000>; - #address-cells = <1>; - #size-cells = <1>; - - nand-ecc-mode = "on-die"; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "kernel"; - reg = <0x0 0x400000>; - }; - - partition@400000 { - label = "ubi"; - reg = <0x400000 0x7c00000>; - }; - }; - }; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ3370-REV2.dtsi b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ3370-REV2.dtsi deleted file mode 100644 index 9a0359d1cc..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ3370-REV2.dtsi +++ /dev/null @@ -1,306 +0,0 @@ -#include "vr9.dtsi" - -#include -#include - -/ { - compatible = "avm,fritz3370-rev2", "lantiq,xway", "lantiq,vr9"; - model = "AVM FRITZ!Box 3370 Rev. 2"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power_green; - led-failsafe = &power_red; - led-running = &power_green; - led-upgrade = &power_green; - - led-dsl = &dsl; - led-internet = &info_green; - led-wifi = &wifi; - }; - - memory@0 { - reg = <0x0 0x8000000>; - }; - - gpio-poweroff { - compatible = "gpio-poweroff"; - gpios = <&gpio 45 GPIO_ACTIVE_HIGH>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - power { - label = "power"; - gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; - linux,code = ; - }; - - wifi { - label = "wlan"; - gpios = <&gpio 29 GPIO_ACTIVE_HIGH>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - - power_green: power { - label = "fritz3370:green:power"; - gpios = <&gpio 32 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - - power_red: power2 { - label = "fritz3370:red:power"; - gpios = <&gpio 33 GPIO_ACTIVE_LOW>; - }; - - info_red { - label = "fritz3370:red:info"; - gpios = <&gpio 34 GPIO_ACTIVE_LOW>; - }; - - wifi: wifi { - label = "fritz3370:green:wlan"; - gpios = <&gpio 35 GPIO_ACTIVE_LOW>; - }; - - dsl: dsl { - label = "fritz3370:green:dsl"; - gpios = <&gpio 36 GPIO_ACTIVE_LOW>; - }; - - lan { - label = "fritz3370:green:lan"; - gpios = <&gpio 38 GPIO_ACTIVE_LOW>; - }; - - info_green: info_green { - label = "fritz3370:green:info"; - gpios = <&gpio 47 GPIO_ACTIVE_LOW>; - }; - }; - - usb0_vbus: regulator-usb0-vbus { - compatible = "regulator-fixed"; - - regulator-name = "USB0_VBUS"; - - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - gpio = <&gpio 14 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; - - usb1_vbus: regulator-usb1-vbus { - compatible = "regulator-fixed"; - - regulator-name = "USB1_VBUS"; - - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - gpio = <&gpio 5 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -ð0 { - lan: interface@0 { - compatible = "lantiq,xrx200-pdi"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - lantiq,switch; - - ethernet@0 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <0>; - phy-mode = "rgmii"; - phy-handle = <&phy0>; - gpios = <&gpio 37 GPIO_ACTIVE_HIGH>; - }; - - ethernet@1 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <1>; - phy-mode = "rgmii"; - phy-handle = <&phy1>; - gpios = <&gpio 44 GPIO_ACTIVE_HIGH>; - }; - - ethernet@2 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <2>; - phy-mode = "gmii"; - phy-handle = <&phy11>; - }; - - ethernet@4 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <4>; - phy-mode = "gmii"; - phy-handle = <&phy13>; - }; - }; - - mdio@0 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "lantiq,xrx200-mdio"; - reg = <0>; - - phy0: ethernet-phy@0 { - reg = <0x0>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - - phy1: ethernet-phy@1 { - reg = <0x1>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - - phy11: ethernet-phy@11 { - reg = <0x11>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - - phy13: ethernet-phy@13 { - reg = <0x13>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - }; -}; - -&gphy0 { - lantiq,gphy-mode = ; -}; - -&gphy1 { - lantiq,gphy-mode = ; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - mdio { - lantiq,groups = "mdio"; - lantiq,function = "mdio"; - }; - - nand { - lantiq,groups = "nand cle", "nand ale", - "nand rd", "nand cs1", "nand rdy"; - lantiq,function = "ebu"; - lantiq,pull = <1>; - }; - - phy-rst { - lantiq,pins = "io37", "io44"; - lantiq,pull = <0>; - lantiq,open-drain = <0>; - lantiq,output = <1>; - }; - - pcie-rst { - lantiq,pins = "io21"; - lantiq,pull = <0>; - lantiq,output = <1>; - }; - }; - - pins_spi_default: pins_spi_default { - spi_in { - lantiq,groups = "spi_di"; - lantiq,function = "spi"; - }; - - spi_out { - lantiq,groups = "spi_do", "spi_clk", - "spi_cs4"; - lantiq,function = "spi"; - lantiq,output = <1>; - }; - }; -}; - -&pcie0 { - gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; - - pcie@0 { - reg = <0 0 0 0 0>; - #interrupt-cells = <1>; - #size-cells = <2>; - #address-cells = <3>; - device_type = "pci"; - - wifi@0,0 { - compatible = "pci0,0"; - reg = <0 0 0 0 0>; - qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:01:00.0.bin */ - }; - }; -}; - -&spi { - status = "okay"; - - pinctrl-names = "default"; - pinctrl-0 = <&pins_spi_default>; - - m25p80@4 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "jedec,spi-nor"; - reg = <4 0>; - spi-max-frequency = <1000000>; - - urlader: partition@0 { - reg = <0x0 0x20000>; - label = "urlader"; - read-only; - }; - - partition@20000 { - reg = <0x20000 0x10000>; - label = "tffs (1)"; - read-only; - }; - - partition@30000 { - reg = <0x30000 0x10000>; - label = "tffs (2)"; - read-only; - }; - }; -}; - -&usb_phy0 { - status = "okay"; -}; - -&usb_phy1 { - status = "okay"; -}; - -&usb0 { - status = "okay"; - vbus-supply = <&usb0_vbus>; -}; - -&usb1 { - status = "okay"; - vbus-supply = <&usb1_vbus>; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ7312.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ7312.dts deleted file mode 100644 index 796b941ede..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ7312.dts +++ /dev/null @@ -1,182 +0,0 @@ -/dts-v1/; - -#include "ar9.dtsi" - -#include - -/ { - compatible = "avm,fritz7312", "lantiq,xway", "lantiq,ar9"; - model = "AVM FRITZ!Box 7312"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power; - led-failsafe = &power; - led-running = &power; - led-upgrade = &power; - - led-internet = &info_green; - led-dsl = &power; - led-wifi = &wlan; - }; - - memory@0 { - reg = <0x0 0x4000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - wlan { - label = "wlan"; - gpios = <&gpio 1 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - dect { - label = "dect"; - gpios = <&gpio 2 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - - power: power { - label = "fritz7312:green:power"; - gpios = <&gpio 44 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - voice { - label = "fritz7312:green:fon"; - gpios = <&gpio 47 GPIO_ACTIVE_LOW>; - }; - dect { - label = "fritz7312:green:dect"; - gpios = <&gpio 38 GPIO_ACTIVE_LOW>; - }; - wlan: wlan { - label = "fritz7312:green:wlan"; - gpios = <&gpio 37 GPIO_ACTIVE_LOW>; - }; - info_green: info_green { - label = "fritz7312:green:info"; - gpios = <&gpio 35 GPIO_ACTIVE_LOW>; - }; - }; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - pci { - lantiq,groups = "gnt1", "req1", "req2", "req4", "gnt2", "gnt3", "gnt4"; - lantiq,function = "pci"; - }; - pci-in { - lantiq,groups = "req1", "req2", "req4"; - lantiq,output = <0>; - lantiq,open-drain = <1>; - lantiq,pull = <2>; - }; - pci-out { - lantiq,groups = "gnt1", "gnt2", "gnt3", "gnt4"; - lantiq,output = <1>; - lantiq,pull = <0>; - }; - ar8030-intr { - lantiq,groups = "exin3"; - lantiq,function = "exin"; - lantiq,pull = <2>; - lantiq,output = <0>; - }; - ar8030-clk { - lantiq,groups = "clkout2"; - lantiq,output = <1>; - lantiq,open-drain; - }; - ar8030-rst { - lantiq,pins = "io34"; - lantiq,output = <1>; - lantiq,pull = <2>; - lantiq,open-drain; - }; - }; -}; - -&gsw { - phy-mode = "rmii"; - phy-handle = <&phy0>; - mtd-mac-address = <&ath9k_cal 0xa91>; - mtd-mac-address-increment = <(-2)>; - - mdio-bus { - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - - phy0: ethernet-phy@0 { - reg = <0>; - reset-gpios = <&gpio 34 GPIO_ACTIVE_LOW>; - }; - }; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x1000000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - ath9k_cal: partition@0 { - label = "urlader"; - reg = <0x00000 0x20000>; - read-only; - }; - - partition@20000 { - label = "firmware"; - reg = <0x20000 0xf60000>; - }; - - partition@f80000 { - label = "tffs (1)"; - reg = <0xf80000 0x40000>; - read-only; - }; - - partition@fc0000 { - label = "tffs (2)"; - reg = <0xfc0000 0x40000>; - read-only; - }; - }; - }; -}; - -&pci0 { - status = "okay"; - req-mask = <0xf>; - gpio-reset = <&gpio 21 GPIO_ACTIVE_LOW>; - - wifi@0,0 { - compatible = "pci0,0"; - reg = <0x7000 0 0 0 0>; - qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:00:0e.0.bin */ - }; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ7320.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ7320.dts deleted file mode 100644 index a4afca11fa..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ7320.dts +++ /dev/null @@ -1,172 +0,0 @@ -/dts-v1/; - -#include "ar9.dtsi" - -#include - -/ { - compatible = "avm,fritz7320", "lantiq,xway", "lantiq,ar9"; - model = "AVM FRITZ!Box 7320"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power; - led-failsafe = &power; - led-running = &power; - led-upgrade = &power; - - led-internet = &info_green; - led-dsl = &power; - led-wifi = &wlan; - }; - - memory@0 { - reg = <0x0 0x4000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - rfkill { - label = "rfkill"; - gpios = <&gpio 1 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - dect { - label = "dect"; - gpios = <&gpio 2 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - power: power { - label = "fritz7320:green:power"; - gpios = <&gpio 44 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - voice { - label = "fritz7320:green:fon"; - gpios = <&gpio 47 GPIO_ACTIVE_LOW>; - }; - dect { - label = "fritz7320:green:dect"; - gpios = <&gpio 38 GPIO_ACTIVE_LOW>; - }; - wlan: wlan { - label = "fritz7320:green:wlan"; - gpios = <&gpio 37 GPIO_ACTIVE_LOW>; - }; - info_green: info_green { - label = "fritz7320:green:info"; - gpios = <&gpio 35 GPIO_ACTIVE_LOW>; - }; - info_red { - label = "fritz7320:red:info"; - gpios = <&gpio 45 GPIO_ACTIVE_LOW>; - }; - }; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - pci { - lantiq,groups = "gnt1", "req1", "req2", "req3", "req4", "gnt2", "gnt3", "gnt4"; - lantiq,function = "pci"; - }; - pci-in { - lantiq,groups = "req1", "req2", "req3", "req4"; - lantiq,output = <0>; - lantiq,open-drain = <1>; - lantiq,pull = <2>; - }; - pci-out { - lantiq,groups = "gnt1", "gnt2", "gnt3", "gnt4"; - lantiq,output = <1>; - lantiq,pull = <0>; - }; - }; -}; - -&gsw { - phy-mode = "mii"; - mtd-mac-address = <&ath9k_cal 0xa91>; - mtd-mac-address-increment = <(-2)>; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x1000000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - ath9k_cal: partition@0 { - label = "urlader"; - reg = <0x00000 0x20000>; - read-only; - }; - - partition@20000 { - label = "firmware"; - reg = <0x20000 0xf60000>; - }; - - partition@f80000 { - label = "tffs (1)"; - reg = <0xf80000 0x40000>; - read-only; - }; - - partition@fc0000 { - label = "tffs (2)"; - reg = <0xfc0000 0x40000>; - read-only; - }; - }; - }; -}; - -&pci0 { - status = "okay"; - req-mask = <0xf>; - gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; - - wifi@0,0 { - compatible = "pci0,0"; - reg = <0x7000 0 0 0 0>; - qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:00:0e.0.bin */ - }; -}; - -&usb_phy0 { - status = "okay"; -}; - -&usb_phy1 { - status = "okay"; -}; - -&usb0 { - status = "okay"; -}; - -&usb1 { - status = "okay"; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ7360SL.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ7360SL.dts deleted file mode 100644 index 599b20a460..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ7360SL.dts +++ /dev/null @@ -1,82 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later OR MIT -/dts-v1/; - -#include "FRITZ736X.dtsi" - -#include -#include - -/ { - compatible = "avm,fritz7360sl", "avm,fritz736x", "lantiq,xway", "lantiq,vr9"; - model = "AVM FRITZ!Box 7360 SL"; -}; - -&power_green { - label = "fritz7360sl:green:power"; -}; - -&power_red { - label = "fritz7360sl:red:power"; -}; - -&info_green { - label = "fritz7360sl:green:info"; -}; - -&wifi { - label = "fritz7360sl:green:wlan"; -}; - -&info_red { - label = "fritz7360sl:red:info"; -}; - -&dect { - label = "fritz7360sl:green:dect"; -}; - -&state_default { - pcie-rst { - lantiq,pins = "io38"; - lantiq,pull = <0>; - lantiq,output = <1>; - }; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x1000000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - urlader: partition@0 { - label = "urlader"; - reg = <0x00000 0x20000>; - read-only; - }; - - partition@20000 { - label = "firmware"; - reg = <0x20000 0xf60000>; - }; - - partition@f80000 { - label = "tffs (1)"; - reg = <0xf80000 0x40000>; - read-only; - }; - - partition@fc0000 { - label = "tffs (2)"; - reg = <0xfc0000 0x40000>; - read-only; - }; - }; - }; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ7362SL.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ7362SL.dts deleted file mode 100644 index 7a6272b988..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ7362SL.dts +++ /dev/null @@ -1,135 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later OR MIT -/dts-v1/; - -#include "FRITZ736X.dtsi" - -#include -#include - -/ { - compatible = "avm,fritz7362sl", "avm,fritz736x", "lantiq,xway", "lantiq,vr9"; - model = "AVM FRITZ!Box 7362 SL"; -}; - -&power_green { - label = "fritz7362sl:green:power"; -}; - -&power_red { - label = "fritz7362sl:red:power"; -}; - -&info_green { - label = "fritz7362sl:green:info"; -}; - -&wifi { - label = "fritz7362sl:green:wlan"; -}; - -&info_red { - label = "fritz7362sl:red:info"; -}; - -&dect { - label = "fritz7362sl:green:dect"; -}; - -&gpio { - pins_spi_default: pins_spi_default { - spi_in { - lantiq,groups = "spi_di"; - lantiq,function = "spi"; - }; - - spi_out { - lantiq,groups = "spi_do", "spi_clk", - "spi_cs4"; - lantiq,function = "spi"; - lantiq,output = <1>; - }; - }; -}; - -&state_default { - nand { - lantiq,groups = "nand ale", "nand cle", - "nand cs1", "nand rd", "nand rdy"; - lantiq,function = "ebu"; - }; - - pcie-rst { - lantiq,pins = "io21"; - lantiq,open-drain = <1>; - lantiq,output = <1>; - }; -}; - -&spi { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&pins_spi_default>; - - flash@4 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "jedec,spi-nor"; - reg = <4 0>; - spi-max-frequency = <1000000>; - - urlader: partition@0 { - reg = <0x0 0x40000>; - label = "urlader"; - read-only; - }; - - partition@40000 { - reg = <0x40000 0x60000>; - label = "tffs (1)"; - read-only; - }; - - partition@A0000 { - reg = <0xA0000 0x60000>; - label = "tffs (2)"; - read-only; - }; - }; -}; - -&localbus { - nand@1 { - compatible = "lantiq,nand-xway"; - lantiq,cs1 = <1>; - bank-width = <1>; - reg = <1 0x0 0x2000000>; - #address-cells = <1>; - #size-cells = <1>; - nand-ecc-mode = "on-die"; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "kernel"; - reg = <0x0 0x400000>; - }; - - partition@400000 { - label = "ubi"; - reg = <0x400000 0x7c00000>; - }; - }; - }; -}; - -&pcie0 { - gpio-reset = <&gpio 21 GPIO_ACTIVE_LOW>; - - pcie@0 { - #size-cells = <1>; - #address-cells = <2>; - }; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ736X.dtsi b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ736X.dtsi deleted file mode 100644 index 9c1d2db8fa..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ736X.dtsi +++ /dev/null @@ -1,205 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later OR MIT -/dts-v1/; - -#include "vr9.dtsi" - -#include -#include - -/ { - compatible = "avm,fritz736x", "lantiq,xway", "lantiq,vr9"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power_green; - led-failsafe = &power_red; - led-running = &power_green; - led-upgrade = &power_green; - led-dsl = &info_green; - led-wifi = &wifi; - }; - - memory@0 { - reg = <0x0 0x8000000>; - }; - - keys { - compatible = "gpio-keys-polled"; - poll-interval = <100>; - - dect { - label = "dect"; - gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; - linux,code = ; - }; - - wifi { - label = "wifi"; - gpios = <&gpio 29 GPIO_ACTIVE_HIGH>; - linux,code = ; - }; - }; - - leds: leds { - compatible = "gpio-leds"; - - power_green: power { - gpios = <&gpio 32 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - - power_red: power2 { - gpios = <&gpio 33 GPIO_ACTIVE_LOW>; - }; - - info_green: info_green { - gpios = <&gpio 47 GPIO_ACTIVE_LOW>; - }; - - wifi: wifi { - gpios = <&gpio 36 GPIO_ACTIVE_LOW>; - }; - - info_red: info_red { - gpios = <&gpio 34 GPIO_ACTIVE_LOW>; - }; - - dect: dect { - gpios = <&gpio 35 GPIO_ACTIVE_LOW>; - }; - }; -}; - -ð0 { - lan: interface@0 { - compatible = "lantiq,xrx200-pdi"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - mtd-mac-address = <&urlader 0xa91>; - mtd-mac-address-increment = <(-2)>; - lantiq,switch; - - ethernet@0 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <0>; - phy-mode = "rmii"; - phy-handle = <&phy0>; - }; - - ethernet@1 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <1>; - phy-mode = "rmii"; - phy-handle = <&phy1>; - }; - - ethernet@2 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <2>; - phy-mode = "gmii"; - phy-handle = <&phy11>; - }; - - ethernet@3 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <4>; - phy-mode = "gmii"; - phy-handle = <&phy13>; - }; - }; - - mdio@0 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "lantiq,xrx200-mdio"; - reg = <0>; - - phy0: ethernet-phy@0 { - reg = <0x00>; - compatible = "ethernet-phy-ieee802.3-c22"; - reset-gpios = <&gpio 37 GPIO_ACTIVE_LOW>; - }; - - phy1: ethernet-phy@1 { - reg = <0x01>; - compatible = "ethernet-phy-ieee802.3-c22"; - reset-gpios = <&gpio 44 GPIO_ACTIVE_LOW>; - }; - - phy11: ethernet-phy@11 { - reg = <0x11>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - - phy13: ethernet-phy@13 { - reg = <0x13>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - }; -}; - -&gphy0 { - lantiq,gphy-mode = ; -}; - -&gphy1 { - lantiq,gphy-mode = ; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - mdio { - lantiq,groups = "mdio"; - lantiq,function = "mdio"; - }; - - phy-rst { - lantiq,pins = "io37", "io44"; - lantiq,pull = <0>; - lantiq,open-drain; - lantiq,output = <1>; - }; - }; - -}; - -&pcie0 { - status = "okay"; - - pcie@0 { - reg = <0 0 0 0 0>; - #interrupt-cells = <1>; - #size-cells = <1>; - #address-cells = <2>; - device_type = "pci"; - - wifi@168c,002e { - compatible = "pci168c,002e"; - reg = <0 0 0 0 0>; - qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:01:00.0.bin */ - }; - }; -}; - -&usb_phy0 { - status = "okay"; -}; - -&usb_phy1 { - status = "okay"; -}; - -&usb0 { - status = "okay"; -}; - -&usb1 { - status = "okay"; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ7412.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ7412.dts deleted file mode 100644 index 3059c12858..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/FRITZ7412.dts +++ /dev/null @@ -1,230 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later OR MIT -/dts-v1/; - -#include "vr9.dtsi" - -#include -#include - -/ { - compatible = "avm,fritz7412", "lantiq,xway", "lantiq,vr9"; - model = "AVM FRITZ!Box 7412"; - - chosen { - bootargs = "console=ttyLTQ0,115200 mem=126M vpe1_load_addr=0x87e00000 vpe1_mem=2M maxvpes=1 maxtcs=1 nosmp"; - }; - - aliases { - led-boot = &power_green; - led-failsafe = &power_red; - led-running = &power_green; - - led-dsl = &info; - led-wifi = &wifi; - }; - - memory@0 { - reg = <0x0 0x8000000>; - }; - - keys { - compatible = "gpio-keys-polled"; - poll-interval = <100>; - - wps { - label = "wps"; - gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; - linux,code = ; - }; - - dect { - label = "dect"; - gpios = <&gpio 2 GPIO_ACTIVE_HIGH>; - linux,code = ; - }; - }; - - leds { - compatible = "gpio-leds"; - - power_green: power_green { - label = "fritz7412:green:power"; - gpios = <&gpio 6 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - - power_red: power_red { - label = "fritz7412:red:power"; - gpios = <&gpio 5 GPIO_ACTIVE_LOW>; - }; - - fon { - label = "fritz7412:green:fon"; - gpios = <&gpio 34 GPIO_ACTIVE_LOW>; - }; - - dect { - label = "fritz7412:green:dect"; - gpios = <&gpio 15 GPIO_ACTIVE_LOW>; - }; - - wifi: wifi { - label = "fritz7412:green:wifi"; - gpios = <&gpio 0 GPIO_ACTIVE_LOW>; - }; - - info: info { - label = "fritz7412:green:info"; - gpios = <&gpio 35 GPIO_ACTIVE_LOW>; - }; - }; -}; - -&localbus { - nand@0 { - compatible = "lantiq,nand-xway"; - bank-width = <2>; - reg = <0 0x0 0x2000000>; - #address-cells = <1>; - #size-cells = <1>; - lantiq,cs = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "urlader"; - reg = <0x0 0x40000>; - read-only; - }; - - partition@40000 { - label = "nand-tffs"; - reg = <0x40000 0x400000>; - read-only; - }; - - partition@440000 { - label = "kernel"; - reg = <0x440000 0x400000>; - }; - - partition@840000 { - label = "ubi"; - reg = <0x840000 0x3000000>; - }; - - partition@3840000 { - label = "reserved-kernel"; - reg = <0x3840000 0x400000>; - read-only; - }; - - partition@3c40000 { - label = "reserved-filesystem"; - reg = <0x3c40000 0x3000000>; - read-only; - }; - - partition@6c40000 { - label = "config"; - reg = <0x6c40000 0x400000>; - read-only; - }; - - partition@6e40000 { - label = "nand-filesystem"; - reg = <0x6e40000 0x400000>; - read-only; - }; - }; - }; -}; - -&pcie0 { - status = "okay"; - gpio-reset = <&gpio 11 GPIO_ACTIVE_HIGH>; - - pcie@0 { - reg = <0 0 0 0 0>; - #interrupt-cells = <1>; - #size-cells = <2>; - #address-cells = <3>; - device_type = "pci"; - - wifi@168c,002e { - compatible = "pci168c,002e"; - reg = <0 0 0 0 0>; - qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:01:00.0.bin */ - }; - }; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - mdio { - lantiq,groups = "mdio"; - lantiq,function = "mdio"; - }; - pcie-rst { - lantiq,pins = "io11"; - lantiq,open-drain = <1>; - lantiq,output = <1>; - }; - nand-mux { - lantiq,groups = "nand cle", "nand ale", - "nand rd", "nand cs1", - "nand rdy"; - lantiq,function = "ebu"; - }; - nand-pins { - lantiq,pins = "io13", "io24", "io49"; - lantiq,pull = <1>; - }; - }; -}; - -&gphy0 { - lantiq,gphy-mode = ; -}; - -ð0 { - lantiq,phys = <&gphy0>; - - interface@0 { - compatible = "lantiq,xrx200-pdi"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - mac-address = [ 00 11 22 33 44 55 ]; - lantiq,switch; - - ethernet@2 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <2>; - phy-mode = "gmii"; - phy-handle = <&phy11>; - }; - }; - - mdio@0 { - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - compatible = "lantiq,xrx200-mdio"; - - phy11: ethernet-phy@11 { - reg = <0x11>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - }; -}; - -&vmmc { - status = "okay"; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/GIGASX76X.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/GIGASX76X.dts deleted file mode 100644 index 36b82515dc..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/GIGASX76X.dts +++ /dev/null @@ -1,130 +0,0 @@ -/dts-v1/; - -#include "danube.dtsi" - -#include - -/ { - compatible = "siemens,gigaset-sx76x", "lantiq,xway", "lantiq,danube"; - model = "Gigaset SX761,SX762,SX763"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - memory@0 { - reg = <0x0 0x2000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - reset { - label = "reset"; - gpios = <&gpio 14 GPIO_ACTIVE_HIGH>; - linux,code = ; - }; - }; - - gpio_export { - compatible = "gpio-export"; - #size-cells = <0>; - - switch { - gpio-export,name = "switch"; - gpio-export,output = <1>; - gpios = <&gpio 19 GPIO_ACTIVE_HIGH>; - }; - }; - - usb_vbus: regulator-usb-vbus { - compatible = "regulator-fixed"; - - regulator-name = "USB_VBUS"; - - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - gpio = <&gpio 29 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - stp { - lantiq,groups = "stp"; - lantiq,function = "stp"; - }; - }; -}; - - -&gpiomm { - status = "okay"; - lantiq,shadow = <0x3>; -}; - -&gpios { - status = "okay"; -}; - -&gsw { - phy-mode = "rmii"; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x2000000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x0 0x30000>; - }; - - partition@10000 { - label = "uboot_env"; - reg = <0x30000 0x10000>; - }; - - partition@40000 { - label = "firmware"; - reg = <0x40000 0x7c0000>; - }; - }; - }; -}; - -&pci0 { - status = "okay"; - gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; -}; - -&usb_phy { - status = "okay"; -}; - -&usb { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; - -&vmmc { - status = "okay"; - gpios = <&gpiomm 1 GPIO_ACTIVE_HIGH>; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/H201L.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/H201L.dts deleted file mode 100644 index 46cae21a58..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/H201L.dts +++ /dev/null @@ -1,175 +0,0 @@ -/dts-v1/; - -#include "ar9.dtsi" - -#include - -/ { - compatible = "zte,h201l", "lantiq,xway", "lantiq,ar9"; - model = "ZTE H210L"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power_green; - led-failsafe = &power_green; - led-running = &power_green; - led-upgrade = &power_green; - - led-dsl = &dsl; - led-internet = &online; - led-usb = &led_usb; - led-wifi = &wifi; - }; - - memory@0 { - reg = <0x0 0x2000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - reset { - label = "reset"; - gpios = <&gpio 53 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - wps { - label = "wps"; - gpios = <&gpio 54 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - rfkill { - label = "rfkill"; - gpios = <&gpio 55 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - - power_green: power { - label = "h201l:green:power"; - gpios = <&gpio 19 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - online: online { - label = "h201l:green:internet"; - gpios = <&gpio 37 GPIO_ACTIVE_LOW>; - }; - dsl: dsl { - label = "h201l:green:dsl"; - gpios = <&gpio 4 GPIO_ACTIVE_LOW>; - }; - phone { - label = "h201l:green:phone"; - gpios = <&gpio 39 GPIO_ACTIVE_LOW>; - }; - wps { - label = "h201l:green:wps"; - gpios = <&gpio 22 GPIO_ACTIVE_LOW>; - }; - wifi: wifi { - label = "h201l:green:wlan"; - gpios = <&gpio 6 GPIO_ACTIVE_LOW>; - }; - led_usb: usb { - label = "h201l:green:usb"; - gpios = <&gpio 14 GPIO_ACTIVE_LOW>; - }; - }; - - gpio_export { - compatible = "gpio-export"; - #size-cells = <0>; - - switch { - gpio-export,name = "switch"; - gpio-export,output = <1>; - gpios = <&gpio 38 GPIO_ACTIVE_HIGH>; - }; - usb { - gpio-export,name = "usb"; - gpio-export,output = <1>; - gpios = <&gpio 28 GPIO_ACTIVE_HIGH>; - }; - wifi { - gpio-export,name = "wifi"; - gpio-export,output = <1>; - gpios = <&gpio 7 GPIO_ACTIVE_HIGH>; - }; - }; - - usb_vbus: regulator-usb-vbus { - compatible = "regulator-fixed"; - - regulator-name = "USB_VBUS"; - - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - gpio = <&gpio 36 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - }; -}; - -&gsw { - phy-mode = "rgmii"; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x2000000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x00000 0x20000>; - read-only; - }; - - partition@20000 { - label = "uboot_env"; - reg = <0x20000 0x10000>; - read-only; - }; - - partition@30000 { - label = "firmware"; - reg = <0x30000 0x7d0000>; - }; - }; - }; -}; - -&usb_phy0 { - status = "okay"; -}; - - -&usb0 { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/P2601HNFX.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/P2601HNFX.dts deleted file mode 100644 index 5606eb6e8b..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/P2601HNFX.dts +++ /dev/null @@ -1,196 +0,0 @@ -/dts-v1/; - -#include "ar9.dtsi" - -#include - -/ { - compatible = "zyxel,p-2601hn", "lantiq,xway", "lantiq,ar9"; - model = "ZyXEL P-2601HN-Fx"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power_green; - led-failsafe = &power_red; - led-running = &power_green; - led-upgrade = &power_green; - - led-dsl = &dsl; - led-internet = &online; - led-wifi = &wifi; - }; - - memory@0 { - reg = <0x0 0x4000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - reset { - label = "reset"; - gpios = <&gpio 53 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - rfkill { - label = "rfkill"; - gpios = <&gpio 54 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - - power_green: power { - label = "p2601hnfx:green:power"; - gpios = <&stp 11 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - power_red: power2 { - label = "p2601hnfx:red:power"; - gpios = <&gpio 29 GPIO_ACTIVE_LOW>; - }; - online: online { - label = "p2601hnfx:green:internet"; - gpios = <&stp 13 GPIO_ACTIVE_LOW>; - }; - online2 { - label = "p2601hnfx:red:internet"; - gpios = <&stp 12 GPIO_ACTIVE_LOW>; - }; - dsl: dsl { - label = "p2601hnfx:green:dsl"; - gpios = <&stp 14 GPIO_ACTIVE_LOW>; - }; - phone { - label = "p2601hnfx:green:phone"; - gpios = <&stp 9 GPIO_ACTIVE_LOW>; - }; - phone2 { - label = "p2601hnfx:orange:phone"; - gpios = <&stp 8 GPIO_ACTIVE_LOW>; - }; - wifi: wifi { - label = "p2601hnfx:green:wireless"; - gpios = <&stp 15 GPIO_ACTIVE_LOW>; - }; - wifi2 { - label = "p2601hnfx:orange:wireless"; - gpios = <&stp 10 GPIO_ACTIVE_LOW>; - }; - }; - - gpio_export { - compatible = "gpio-export"; - #size-cells = <0>; - - switch { - gpio-export,name = "switch"; - gpio-export,output = <1>; - gpios = <&gpio 50 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - stp { - lantiq,groups = "stp"; - lantiq,function = "stp"; - lantiq,pull = <2>; - lantiq,open-drain = <0>; - lantiq,output = <1>; - }; - exin { - lantiq,groups = "exin1"; - lantiq,function = "exin"; - }; - pci { - lantiq,groups = "gnt1"; - lantiq,function = "pci"; - }; - conf_out { - lantiq,pins = "io4", "io5", "io6"; - lantiq,open-drain; - lantiq,pull = <0>; - }; - mdio { - lantiq,groups = "mdio"; - lantiq,function = "mdio"; - }; - }; - - usb_vbus: regulator-usb-vbus { - compatible = "regulator-fixed"; - - regulator-name = "USB_VBUS"; - - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - gpio = <&gpio 9 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -&gsw { - phy-mode = "rmii"; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x2000000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x00000 0x40000>; - read-only; - }; - - partition@40000 { - label = "uboot_env"; - reg = <0x40000 0x20000>; - read-only; - }; - - partition@60000 { - label = "firmware"; - reg = <0x60000 0xfa0000>; - }; - }; - }; -}; - -&stp { - status = "okay"; - lantiq,shadow = <0xfff>; - lantiq,groups = <0x3>; -}; - -&usb_phy0 { - status = "okay"; -}; - -&usb0 { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/P2812HNUF1.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/P2812HNUF1.dts deleted file mode 100644 index d907d64c8c..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/P2812HNUF1.dts +++ /dev/null @@ -1,70 +0,0 @@ -/dts-v1/; - -#include "P2812HNUFX.dtsi" - -/ { - compatible = "zyxel,p-2812hnu-f1", "zyxel,p-2812hnu", "lantiq,xway", "lantiq,vr9"; - model = "ZyXEL P-2812HNU-F1"; - - aliases { - led-usb = &led_usb1; - led-usb2 = &led_usb2; - }; - - gpio-leds { - led_usb1: usb1 { - label = "p2812hnuf1:green:usb1"; - gpios = <&gpio 38 GPIO_ACTIVE_LOW>; - }; - led_usb2: usb2 { - label = "p2812hnuf1:green:usb2"; - gpios = <&gpio 44 GPIO_ACTIVE_LOW>; - }; - }; -}; - -&localbus { - nand@0 { - compatible = "lantiq,nand-xway"; - lantiq,cs = <1>; - bank-width = <2>; - reg = <0 0x0 0x2000000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x00000 0x40000>; - }; - partition@40000 { - label = "uboot-env"; - reg = <0x40000 0x20000>; - }; - partition@60000 { - label = "kernel"; - reg = <0x60000 0x300000>; - }; - partition@360000 { - label = "ubi"; - reg = <0x360000 0x7ca0000>; - }; - }; - }; -}; - -&pci0 { - wifi@1814,3062 { - compatible = "pci1814,3062"; - reg = <0x7000 0 0 0 0>; - ralink,eeprom = "RT3062.eeprom"; - }; -}; - -&pcie0 { - status = "disabled"; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/P2812HNUF3.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/P2812HNUF3.dts deleted file mode 100644 index 202226aa86..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/P2812HNUF3.dts +++ /dev/null @@ -1,64 +0,0 @@ -/dts-v1/; - -#include "P2812HNUFX.dtsi" - -/ { - compatible = "zyxel,p-2812hnu-f3", "zyxel,p-2812hnu", "lantiq,xway", "lantiq,vr9"; - model = "ZyXEL P-2812HNU-F3"; -}; - -&pci0 { - wifi@1814,3092 { - compatible = "pci1814,3092"; - reg = <0x7000 0 0 0 0>; - ralink,eeprom = "RT3092.eeprom"; - }; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x800000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x0 0x50000>; - read-only; - }; - partition@50000 { - label = "uboot-env"; - reg = <0x50000 0x10000>; - }; - partition@60000 { - label = "unused"; - reg = <0x60000 0x7a0000>; - }; - }; - }; - - nand@1 { - compatible = "lantiq,nand-xway"; - lantiq,cs = <1>; - bank-width = <2>; - reg = <1 0x0 0x2000000>; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "kernel"; - reg = <0x0 0x200000>; - }; - partition@200000 { - label = "ubi"; - reg = <0x200000 0x7e00000>; - }; - }; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/P2812HNUFX.dtsi b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/P2812HNUFX.dtsi deleted file mode 100644 index 65424e3eff..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/P2812HNUFX.dtsi +++ /dev/null @@ -1,298 +0,0 @@ -#include "vr9.dtsi" - -#include -#include - -/ { - compatible = "zyxel,p-2812hnu", "lantiq,xway", "lantiq,vr9"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power_green; - led-failsafe = &power_red; - led-running = &power_green; - led-upgrade = &power_green; - - led-dsl = &dsl_green; - led-internet = &internet_green; - led-wifi = &wireless_green; - }; - - memory@0 { - reg = <0x0 0x8000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - reset { - label = "reset"; - gpios = <&gpio 39 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - rfkill { - label = "rfkill"; - gpios = <&gpio 1 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - - internet_red { - label = "p2812hnufx:red:internet"; - gpios = <&stp 16 GPIO_ACTIVE_LOW>; - }; - internet_green: internet_green { - label = "p2812hnufx:green:internet"; - gpios = <&stp 17 GPIO_ACTIVE_LOW>; - }; - dsl_green: dsl_green { - label = "p2812hnufx:green:dsl"; - gpios = <&stp 18 GPIO_ACTIVE_LOW>; - }; - dsl_orange { - label = "p2812hnufx:orange:dsl"; - gpios = <&stp 19 GPIO_ACTIVE_LOW>; - }; - wireless_orange { - label = "p2812hnufx:orange:wlan"; - gpios = <&stp 20 GPIO_ACTIVE_LOW>; - }; - wireless_green: wireless_green { - label = "p2812hnufx:green:wlan"; - gpios = <&stp 21 GPIO_ACTIVE_LOW>; - }; - power_red: power { - label = "p2812hnufx:red:power"; - gpios = <&stp 22 GPIO_ACTIVE_LOW>; - }; - power_green: power2 { - label = "p2812hnufx:green:power"; - gpios = <&stp 23 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - phone1 { - label = "p2812hnufx:green:phone"; - gpios = <&gpio 11 GPIO_ACTIVE_LOW>; - }; - phone1warn { - label = "p2812hnufx:orange:phone"; - gpios = <&gpio 12 GPIO_ACTIVE_LOW>; - }; - phone2warn { - label = "p2812hnufx:orange:phone2"; - gpios = <&gpio 26 GPIO_ACTIVE_LOW>; - }; - phone2 { - label = "p2812hnufx:green:phone2"; - gpios = <&gpio 28 GPIO_ACTIVE_LOW>; - }; - }; - - usb_vbus: regulator-usb-vbus { - compatible = "regulator-fixed"; - - regulator-name = "USB_VBUS"; - - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - gpio = <&gpio 33 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -ð0 { - lan: interface@0 { - compatible = "lantiq,xrx200-pdi"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - mac-address = [ 00 11 22 33 44 55 ]; - lantiq,switch; - - ethernet@0 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <0>; - phy-mode = "rgmii"; - phy-handle = <&phy0>; - }; - ethernet@1 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <1>; - phy-mode = "rgmii"; - phy-handle = <&phy1>; - }; - ethernet@2 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <2>; - phy-mode = "gmii"; - phy-handle = <&phy11>; - }; - ethernet@4 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <4>; - phy-mode = "gmii"; - phy-handle = <&phy13>; - }; - ethernet@5 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <5>; - phy-mode = "rgmii"; - phy-handle = <&phy5>; - }; - }; - - mdio@0 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "lantiq,xrx200-mdio"; - reg = <0>; - - phy0: ethernet-phy@0 { - reg = <0x0>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - phy1: ethernet-phy@1 { - reg = <0x1>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - phy5: ethernet-phy@5 { - reg = <0x5>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - phy11: ethernet-phy@11 { - reg = <0x11>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - phy13: ethernet-phy@13 { - reg = <0x13>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - }; -}; - -&gphy0 { - lantiq,gphy-mode = ; -}; - -&gphy1 { - lantiq,gphy-mode = ; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - exin3 { - lantiq,groups = "exin3"; - lantiq,function = "exin"; - }; - mdio { - lantiq,groups = "mdio"; - lantiq,function = "mdio"; - }; - gphy-leds { - lantiq,groups = "gphy0 led1", "gphy1 led1", - "gphy0 led2", "gphy1 led2"; - lantiq,function = "gphy"; - lantiq,pull = <2>; - lantiq,open-drain = <0>; - lantiq,output = <1>; - }; - stp { - lantiq,groups = "stp"; - lantiq,function = "stp"; - lantiq,pull = <2>; - lantiq,open-drain = <0>; - lantiq,output = <1>; - }; - pci-in { - lantiq,groups = "req1"; - lantiq,function = "pci"; - lantiq,output = <0>; - lantiq,open-drain = <1>; - lantiq,pull = <2>; - }; - pci-out { - lantiq,groups = "gnt1"; - lantiq,function = "pci"; - lantiq,output = <1>; - lantiq,open-drain = <0>; - lantiq,pull = <0>; - }; - pci_rst { - lantiq,pins = "io21"; - lantiq,output = <1>; - lantiq,open-drain = <0>; - lantiq,pull = <2>; - }; - pcie-rst { - lantiq,pins = "io38"; - lantiq,pull = <0>; - lantiq,output = <1>; - }; - ifxhcd-rst { - lantiq,pins = "io33"; - lantiq,pull = <0>; - lantiq,open-drain = <0>; - lantiq,output = <1>; - }; - nand_out { - lantiq,groups = "nand cle", "nand ale"; - lantiq,function = "ebu"; - lantiq,output = <1>; - lantiq,open-drain = <0>; - lantiq,pull = <0>; - }; - nand_cs1 { - lantiq,groups = "nand cs1"; - lantiq,function = "ebu"; - lantiq,open-drain = <0>; - lantiq,pull = <0>; - }; - }; -}; - -&pci0 { - status = "okay"; - gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; -}; - -&stp { - status = "okay"; - - lantiq,shadow = <0xffffff>; - lantiq,groups = <0x7>; - lantiq,dsl = <0x0>; - lantiq,phy1 = <0x0>; - lantiq,phy2 = <0x0>; -}; - -&usb_phy0 { - status = "okay"; -}; - -&usb_phy1 { - status = "okay"; -}; - -&usb0 { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; - -&usb1 { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/TDW8970.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/TDW8970.dts deleted file mode 100644 index 25eb3dac67..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/TDW8970.dts +++ /dev/null @@ -1,8 +0,0 @@ -/dts-v1/; - -#include "TDW89X0.dtsi" - -/ { - compatible = "tplink,tdw8970", "tplink,tdw89x0", "lantiq,xway", "lantiq,vr9"; - model = "TP-LINK TD-W8970"; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/TDW8980.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/TDW8980.dts deleted file mode 100644 index 76875e735d..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/TDW8980.dts +++ /dev/null @@ -1,33 +0,0 @@ -/dts-v1/; - -#include "TDW89X0.dtsi" - -/ { - compatible = "tplink,tdw8980", "tplink,tdw89x0", "lantiq,xway", "lantiq,vr9"; - model = "TP-LINK TD-W8980"; - - gpio-leds { - wifi2 { - label = "tdw8980:green:wlan5ghz"; - gpios = <&gpio 24 GPIO_ACTIVE_LOW>; - }; - }; -}; - -&gpio { - state_default: pinmux { - pci_rst { - lantiq,pins = "io21"; - lantiq,output = <1>; - lantiq,open-drain; - }; - }; -}; - -&pci0 { - status = "okay"; - lantiq,bus-clock = <33333333>; - interrupt-map-mask = <0xf800 0x0 0x0 0x7>; - interrupt-map = <0x7000 0 0 1 &icu0 30 1>; - gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/TDW89X0.dtsi b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/TDW89X0.dtsi deleted file mode 100644 index 71e051a316..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/TDW89X0.dtsi +++ /dev/null @@ -1,299 +0,0 @@ -#include "vr9.dtsi" - -#include -#include - -/ { - compatible = "tplink,tdw89x0", "lantiq,xway", "lantiq,vr9"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - /* the power led can't be controlled, use the wps led instead */ - led-boot = &wps; - led-failsafe = &wps; - - led-dsl = &dsl; - led-internet = &internet; - led-wifi = &wifi; - led-usb = &led_usb0; - led-usb2 = &led_usb2; - }; - - memory@0 { - reg = <0x0 0x4000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - reset { - label = "reset"; - gpios = <&gpio 0 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - wifi { - label = "wifi"; - gpios = <&gpio 9 GPIO_ACTIVE_HIGH>; - linux,code = ; - linux,input-type = ; - }; - - wps { - label = "wps"; - gpios = <&gpio 39 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - /* - power is not controllable via gpio - */ - dsl: dsl { - label = "tdw89x0:green:dsl"; - gpios = <&gpio 4 GPIO_ACTIVE_HIGH>; - }; - internet: internet { - label = "tdw89x0:green:internet"; - gpios = <&gpio 5 GPIO_ACTIVE_HIGH>; - }; - - led_usb0: usb0 { - label = "tdw89x0:green:usb"; - gpios = <&gpio 19 GPIO_ACTIVE_HIGH>; - }; - led_usb2: usb2 { - label = "tdw89x0:green:usb2"; - gpios = <&gpio 20 GPIO_ACTIVE_HIGH>; - }; - wps: wps { - label = "tdw89x0:green:wps"; - gpios = <&gpio 37 GPIO_ACTIVE_HIGH>; - }; - }; - - wifi-leds { - compatible = "gpio-leds"; - - wifi: wifi { - label = "tdw89x0:green:wifi"; - gpios = <&ath9k 0 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "phy0tpt"; - }; - }; - - - usb_vbus: regulator-usb-vbus { - compatible = "regulator-fixed"; - - regulator-name = "USB_VBUS"; - - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - gpio = <&gpio 33 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -ð0 { - lan: interface@0 { - compatible = "lantiq,xrx200-pdi"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - mtd-mac-address = <&ath9k_cal 0xf100>; - lantiq,switch; - - ethernet@0 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <0>; - phy-mode = "rgmii"; - phy-handle = <&phy0>; - // gpios = <&gpio 42 GPIO_ACTIVE_LOW>; - }; - ethernet@5 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <5>; - phy-mode = "rgmii"; - phy-handle = <&phy5>; - }; - ethernet@2 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <2>; - phy-mode = "gmii"; - phy-handle = <&phy11>; - }; - ethernet@3 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <4>; - phy-mode = "gmii"; - phy-handle = <&phy13>; - }; - }; - - mdio@0 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "lantiq,xrx200-mdio"; - reg = <0>; - - phy0: ethernet-phy@0 { - reg = <0x0>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - phy5: ethernet-phy@5 { - reg = <0x5>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - phy11: ethernet-phy@11 { - reg = <0x11>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - phy13: ethernet-phy@13 { - reg = <0x13>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - }; -}; - -&gphy0 { - lantiq,gphy-mode = ; -}; - -&gphy1 { - lantiq,gphy-mode = ; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - mdio { - lantiq,groups = "mdio"; - lantiq,function = "mdio"; - }; - gphy-leds { - lantiq,groups = "gphy0 led1", "gphy1 led1"; - lantiq,function = "gphy"; - lantiq,pull = <2>; - lantiq,open-drain = <0>; - lantiq,output = <1>; - }; - phy-rst { - lantiq,pins = "io42"; - lantiq,pull = <0>; - lantiq,open-drain = <0>; - lantiq,output = <1>; - }; - pcie-rst { - lantiq,pins = "io38"; - lantiq,pull = <0>; - lantiq,output = <1>; - }; - }; - pins_spi_default: pins_spi_default { - spi_in { - lantiq,groups = "spi_di"; - lantiq,function = "spi"; - }; - spi_out { - lantiq,groups = "spi_do", "spi_clk", - "spi_cs4"; - lantiq,function = "spi"; - lantiq,output = <1>; - }; - }; -}; - -&pcie0 { - pcie@0 { - reg = <0 0 0 0 0>; - #interrupt-cells = <1>; - #size-cells = <2>; - #address-cells = <3>; - device_type = "pci"; - - ath9k: wifi@168c,002e { - compatible = "pci168c,002e"; - reg = <0 0 0 0 0>; - #gpio-cells = <2>; - gpio-controller; - qca,no-eeprom; - qca,disable-5ghz; - mtd-mac-address = <&ath9k_cal 0xf100>; - mtd-mac-address-increment = <2>; - }; - }; -}; - -&spi { - status = "okay"; - - pinctrl-names = "default"; - pinctrl-0 = <&pins_spi_default>; - - m25p80@4 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "jedec,spi-nor"; - reg = <4 0>; - spi-max-frequency = <33250000>; - m25p,fast-read; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - reg = <0x0 0x20000>; - label = "u-boot"; - read-only; - }; - - partition@20000 { - reg = <0x20000 0x7a0000>; - label = "firmware"; - }; - - partition@7c0000 { - reg = <0x7c0000 0x10000>; - label = "config"; - read-only; - }; - - ath9k_cal: partition@7d0000 { - reg = <0x7d0000 0x30000>; - label = "boardconfig"; - read-only; - }; - }; - }; -}; - -&usb_phy0 { - status = "okay"; -}; - -&usb_phy1 { - status = "okay"; -}; - -&usb0 { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; - -&usb1 { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VG3503J.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VG3503J.dts deleted file mode 100644 index 9735b2e011..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VG3503J.dts +++ /dev/null @@ -1,165 +0,0 @@ -/dts-v1/; - -#include "vr9.dtsi" - -#include -#include - -/ { - compatible = "arcadyan,vg3503j", "lantiq,xway", "lantiq,vr9"; - model = "BT OpenReach VDSL Modem"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power_green; - led-failsafe = &power_red; - led-running = &power_green; - led-upgrade = &power_green; - - led-dsl = &dsl; - }; - - memory@0 { - reg = <0x0 0x2000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - reset { - label = "reset"; - gpios = <&gpio 6 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - - power_red: power2 { - label = "vg3503j:red:power"; - gpios = <&gpio 14 GPIO_ACTIVE_LOW>; - }; - dsl: dsl { - label = "vg3503j:green:dsl"; - gpios = <&gpio 19 GPIO_ACTIVE_LOW>; - }; - power_green: power { - label = "vg3503j:green:power"; - gpios = <&gpio 28 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - }; -}; - -ð0 { - interface@0 { - compatible = "lantiq,xrx200-pdi"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - - lantiq,switch; - ethernet@2 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <2>; - phy-mode = "mii"; - phy-handle = <&phy11>; - }; - ethernet@4 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <4>; - phy-mode = "mii"; - phy-handle = <&phy13>; - }; - }; - - mdio@0 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "lantiq,xrx200-mdio"; - reg = <0>; - - phy11: ethernet-phy@11 { - reg = <0x11>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - lantiq,led1h = <0x70>; - lantiq,led1l = <0x00>; - lantiq,led2h = <0x00>; - lantiq,led2l = <0x03>; - }; - phy13: ethernet-phy@13 { - reg = <0x13>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - lantiq,led1h = <0x70>; - lantiq,led1l = <0x00>; - lantiq,led2h = <0x00>; - lantiq,led2l = <0x03>; - }; - }; -}; - -&gphy0 { - lantiq,gphy-mode = ; -}; - -&gphy1 { - lantiq,gphy-mode = ; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - mdio { - lantiq,groups = "mdio"; - lantiq,function = "mdio"; - }; - gphy-leds { - lantiq,groups = "gphy0 led0", "gphy0 led1", - "gphy0 led2", "gphy1 led0", - "gphy1 led1", "gphy1 led2"; - lantiq,function = "gphy"; - lantiq,pull = <2>; - lantiq,open-drain = <0>; - lantiq,output = <1>; - }; - }; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x2000000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x00000 0x20000>; - }; - - partition@20000 { - label = "firmware"; - reg = <0x20000 0x7d0000>; - }; - - partition@7f0000 { - label = "uboot-env"; - reg = <0x7f0000 0x10000>; - }; - }; - }; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VGV7510KW22.dtsi b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VGV7510KW22.dtsi deleted file mode 100644 index 811f39d08b..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VGV7510KW22.dtsi +++ /dev/null @@ -1,269 +0,0 @@ -#include "vr9.dtsi" - -#include -#include - -/ { - compatible = "arcadyan,vgv7510kw22", "lantiq,xway", "lantiq,vr9"; - - chosen { - bootargs = "console=ttyLTQ0,115200 mem=62M vpe1_load_addr=0x83e00000 vpe1_mem=2M maxvpes=1 maxtcs=1 nosmp"; - }; - - aliases { - led-boot = &power_green; - led-failsafe = &power_red; - led-running = &power_green; - led-upgrade = &power_green; - - led-dsl = &dsl; - led-internet = &internet_green; - led-wifi = &wifi; - }; - - memory@0 { - reg = <0x0 0x4000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - reset { - label = "reset"; - gpios = <&gpio 6 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - wps { - label = "wps"; - gpios = <&gpio 9 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - - dsl: dsl { - label = "vgv7510kw22:green:dsl"; - gpios = <&gpio 2 GPIO_ACTIVE_LOW>; - }; - - internet_red { - label = "vgv7510kw22:red:internet"; - gpios = <&gpio 10 GPIO_ACTIVE_LOW>; - }; - - info_red { - label = "vgv7510kw22:red:info"; - gpios = <&gpio 12 GPIO_ACTIVE_LOW>; - }; - - power_green: power { - label = "vgv7510kw22:green:power"; - gpios = <&gpio 14 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - - info_green { - label = "vgv7510kw22:green:info"; - gpios = <&gpio 15 GPIO_ACTIVE_LOW>; - }; - - internet_green: internet_green { - label = "vgv7510kw22:green:internet"; - gpios = <&gpio 19 GPIO_ACTIVE_LOW>; - }; - - wifi: wifi { - label = "vgv7510kw22:green:wlan"; - gpios = <&gpio 20 GPIO_ACTIVE_LOW>; - }; - - power_red: power2 { - label = "vgv7510kw22:red:power"; - gpios = <&gpio 28 GPIO_ACTIVE_LOW>; - }; - - phone { - label = "vgv7510kw22:green:telefon"; - gpios = <&gpio 29 GPIO_ACTIVE_LOW>; - }; - }; - - usb_vbus: regulator-usb-vbus { - compatible = "regulator-fixed"; - - regulator-name = "USB_VBUS"; - - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - gpio = <&gpio 47 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -ð0 { - lan: interface@0 { - compatible = "lantiq,xrx200-pdi"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - mtd-mac-address = <&boardconfig 0x16>; - lantiq,switch; - - ethernet@0 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <0>; - phy-mode = "mii"; - phy-handle = <&phy1>; - }; - ethernet@2 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <2>; - phy-mode = "mii"; - phy-handle = <&phy11>; - }; - ethernet@3 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <3>; - phy-mode = "mii"; - phy-handle = <&phy12>; - }; - ethernet@4 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <4>; - phy-mode = "mii"; - phy-handle = <&phy13>; - }; - ethernet@5 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <5>; - phy-mode = "mii"; - phy-handle = <&phy14>; - }; - }; - - mdio@0 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "lantiq,xrx200-mdio"; - reg = <0>; - - phy1: ethernet-phy@1 { - reg = <0x1>; - compatible = "ethernet-phy-ieee802.3-c22"; - }; - - phy11: ethernet-phy@11 { - reg = <0x11>; - compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; - }; - phy12: ethernet-phy@12 { - reg = <0x12>; - compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; - }; - phy13: ethernet-phy@13 { - reg = <0x13>; - compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; - }; - phy14: ethernet-phy@14 { - reg = <0x14>; - compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; - }; - }; -}; - -&gphy0 { - lantiq,gphy-mode = ; -}; - -&gphy1 { - lantiq,gphy-mode = ; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - gphy-leds { - lantiq,groups = "gphy0 led0", "gphy0 led1", - "gphy1 led0", "gphy1 led1"; - lantiq,function = "gphy"; - lantiq,open-drain = <0>; - lantiq,pull = <2>; - lantiq,output = <1>; - }; - mdio { - lantiq,groups = "mdio"; - lantiq,function = "mdio"; - }; - pci-rst { - lantiq,pins = "io21"; - lantiq,open-drain = <0>; - lantiq,pull = <0>; - lantiq,output = <1>; - }; - }; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x1000000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - boardconfig: partition@fe0000 { - label = "board_config"; - reg = <0xfe0000 0x20000>; - read-only; - }; - }; - }; -}; - -&pci0 { - status = "okay"; - gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; - - wifi@1814,3592 { - compatible = "pci1814,3592"; - reg = <0x7000 0 0 0 0>; - ralink,mtd-eeprom = <&boardconfig 0x410>; - ralink,mtd-eeprom-swap; - mtd-mac-address = <&boardconfig 0x16>; - mtd-mac-address-increment = <1>; - }; -}; - -&pcie0 { - status = "disabled"; -}; - -&usb_phy0 { - status = "okay"; -}; - -&usb0 { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; - -&vmmc { - status = "okay"; - gpios = <&gpio 30 GPIO_ACTIVE_HIGH //fxs relay - &gpio 31 GPIO_ACTIVE_HIGH //still unknown - &gpio 3 GPIO_ACTIVE_HIGH>; //reset_slic? -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VGV7510KW22BRN.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VGV7510KW22BRN.dts deleted file mode 100644 index 94b96d74d9..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VGV7510KW22BRN.dts +++ /dev/null @@ -1,65 +0,0 @@ -/dts-v1/; - -#include "VGV7510KW22.dtsi" - -/ { - compatible = "arcadyan,vgv7510kw22-brn", "arcadyan,vgv7510kw22", "lantiq,xway", "lantiq,vr9"; - model = "o2 Box 6431"; - - sram@1f000000 { - cgu@103000 { - lantiq,phy-clk-src = <0x2>; - }; - }; -}; - -&localbus { - nor@0 { - partitions { - partition@0 { - label = "Boot"; - reg = <0x00000 0x40000>; - read-only; - }; - - partition@40000 { - label = "Configuration"; - reg = <0x40000 0x40000>; - read-only; - }; - - partition@80000 { - label = "Certificate"; - reg = <0x80000 0x20000>; - read-only; - }; - - partition@a0000 { - label = "Special_Area"; - reg = <0xa0000 0x20000>; - read-only; - }; - - partition@c0000 { - compatible = "brnboot,root-selector"; - label = "Primary_Setting"; - reg = <0xc0000 0x20000>; - read-only; - }; - - partition@e0000 { - label = "Code_Image_0"; - reg = <0xe0000 0x780000>; - brnboot,root-id = <0x00>; - read-only; - }; - - partition@860000 { - label = "Code_Image_1"; - reg = <0x860000 0x780000>; - brnboot,root-id = <0x01>; - read-only; - }; - }; - }; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VGV7510KW22NOR.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VGV7510KW22NOR.dts deleted file mode 100644 index cc84c63f2e..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VGV7510KW22NOR.dts +++ /dev/null @@ -1,31 +0,0 @@ -/dts-v1/; - -#include "VGV7510KW22.dtsi" - -/ { - compatible = "arcadyan,vgv7510kw22-nor", "arcadyan,vgv7510kw22", "lantiq,xway", "lantiq,vr9"; - model = "o2 Box 6431"; -}; - -&localbus { - nor@0 { - partitions { - partition@0 { - label = "uboot"; - reg = <0x0 0x60000>; /* 384 KiB */ - read-only; - }; - - partition@60000 { - label = "uboot-env"; - reg = <0x60000 0x20000>; /* 128 KiB */ - read-only; - }; - - partition@80000 { - label = "firmware"; - reg = <0x80000 0xf60000>; /* 15744 KiB */ - }; - }; - }; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VGV7519.dtsi b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VGV7519.dtsi deleted file mode 100644 index f69b302bcd..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VGV7519.dtsi +++ /dev/null @@ -1,314 +0,0 @@ -#include "vr9.dtsi" - -#include -#include - -/ { - compatible = "arcadyan,vgv7519", "lantiq,xway", "lantiq,vr9"; - - chosen { - bootargs = "console=ttyLTQ0,115200 mem=62M vpe1_load_addr=0x83e00000 vpe1_mem=2M maxvpes=1 maxtcs=1 nosmp"; - }; - - aliases { - led-boot = &power_green; - led-failsafe = &power_red; - led-running = &power_green; - led-upgrade = &power_green; - - led-dsl = &broadband_green; - led-internet = &internet_green; - led-wifi = &wireless_green; - }; - - memory@0 { - reg = <0x0 0x4000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - reset { - label = "reset"; - gpios = <&gpio 9 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - eco { - label = "eco"; - gpios = <&gpio 41 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - rfkill { - label = "rfkill"; - gpios = <&gpio 45 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - wps { - label = "wps"; - gpios = <&gpio 10 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - - eco { - label = "vgv7519:blue:eco"; - gpios = <&stp 2 GPIO_ACTIVE_LOW>; - }; - wps_red { - label = "vgv7519:red:wps"; - gpios = <&stp 3 GPIO_ACTIVE_LOW>; - }; - wps_green { - label = "vgv7519:green:wps"; - gpios = <&stp 4 GPIO_ACTIVE_LOW>; - }; - upgrade { - label = "vgv7519:blue:upgrade"; - gpios = <&stp 5 GPIO_ACTIVE_LOW>; - }; - tv { - label = "vgv7519:green:tv"; - gpios = <&stp 6 GPIO_ACTIVE_LOW>; - }; - internet_green: internet_green { - label = "vgv7519:green:internet"; - gpios = <&stp 7 GPIO_ACTIVE_LOW>; - }; - internet_red { - label = "vgv7519:red:internet"; - gpios = <&stp 8 GPIO_ACTIVE_LOW>; - }; - broadband_red { - label = "vgv7519:red:broadband"; - gpios = <&stp 9 GPIO_ACTIVE_LOW>; - }; - broadband_green: broadband_green { - label = "vgv7519:green:broadband"; - gpios = <&stp 10 GPIO_ACTIVE_LOW>; - }; - voice { - label = "vgv7519:green:voice"; - gpios = <&stp 11 GPIO_ACTIVE_LOW>; - }; - wireless_red { - label = "vgv7519:red:wireless"; - gpios = <&stp 12 GPIO_ACTIVE_LOW>; - }; - wireless_green: wireless_green { - label = "vgv7519:green:wireless"; - gpios = <&stp 13 GPIO_ACTIVE_LOW>; - }; - power_green: power2 { - label = "vgv7519:green:power"; - gpios = <&stp 14 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - power_red: power { - label = "vgv7519:red:power"; - gpios = <&stp 15 GPIO_ACTIVE_LOW>; - }; - }; - - usb_vbus: regulator-usb-vbus { - compatible = "regulator-fixed"; - - regulator-name = "USB_VBUS"; - - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - gpio = <&gpio 32 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -ð0 { - lan: interface@0 { - compatible = "lantiq,xrx200-pdi"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - mtd-mac-address = <&boardconfig 0x16>; - mtd-mac-address-increment = <1>; - lantiq,switch; - - ethernet@0 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <0>; - phy-mode = "rgmii"; - phy-handle = <&phy0>; - }; - ethernet@1 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <1>; - phy-mode = "rgmii"; - phy-handle = <&phy1>; - }; - ethernet@2 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <2>; - phy-mode = "gmii"; - phy-handle = <&phy11>; - }; - ethernet@4 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <4>; - phy-mode = "gmii"; - phy-handle = <&phy13>; - }; - ethernet@5 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <5>; - phy-mode = "rgmii"; - phy-handle = <&phy5>; - }; - }; - - mdio@0 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "lantiq,xrx200-mdio"; - reg = <0>; - - phy0: ethernet-phy@0 { - reg = <0x0>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - phy1: ethernet-phy@1 { - reg = <0x1>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - phy5: ethernet-phy@5 { - reg = <0x5>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - phy11: ethernet-phy@11 { - reg = <0x11>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - phy13: ethernet-phy@13 { - reg = <0x13>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - }; -}; - -&gphy0 { - lantiq,gphy-mode = ; -}; - -&gphy1 { - lantiq,gphy-mode = ; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - stp { - lantiq,groups = "stp"; - lantiq,function = "stp"; - lantiq,open-drain = <0>; - lantiq,output = <1>; - lantiq,pull = <0>; - }; - mdio { - lantiq,groups = "mdio"; - lantiq,function = "mdio"; - }; - pci-rst { - lantiq,pins = "io21"; - lantiq,open-drain = <0>; - lantiq,pull = <0>; - lantiq,output = <1>; - }; - gphy-leds { - lantiq,groups = "gphy0 led1", "gphy1 led0"; - lantiq,function = "gphy"; - lantiq,open-drain = <0>; - lantiq,pull = <0>; - lantiq,output = <1>; - }; - }; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x800000>, <1 0x800000 0x800000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - boardconfig: partition@40000 { - label = "board_config"; - reg = <0x40000 0x10000>; - read-only; - }; - }; - }; -}; - -&pci0 { - status = "okay"; - gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; - - wifi@1814,3091 { - compatible = "pci1814,3091"; - reg = <0x7000 0 0 0 0>; - ralink,mtd-eeprom = <&boardconfig 0x410>; - ralink,mtd-eeprom-swap; - mtd-mac-address = <&boardconfig 0x16>; - mtd-mac-address-increment = <1>; - }; -}; - -&pcie0 { - status = "disabled"; -}; - -&stp { - status = "okay"; - lantiq,shadow = <0xffff>; - lantiq,groups = <0x3>; - lantiq,dsl = <0x0>; - lantiq,phy1 = <0x0>; - lantiq,phy2 = <0x0>; - /* lantiq,rising; */ -}; - -&usb_phy0 { - status = "okay"; -}; - -&usb_phy1 { - status = "okay"; -}; - -&usb0 { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; - -&usb1 { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; - -&vmmc { - status = "okay"; - gpios = <&gpio 30 GPIO_ACTIVE_HIGH //fxs relay - &gpio 31 GPIO_ACTIVE_HIGH //still unknown - &gpio 3 GPIO_ACTIVE_HIGH>; //reset_slic? -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VGV7519BRN.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VGV7519BRN.dts deleted file mode 100644 index 1e6a65ebb0..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VGV7519BRN.dts +++ /dev/null @@ -1,70 +0,0 @@ -/dts-v1/; - -#include "VGV7519.dtsi" - -/ { - compatible = "arcadyan,vgv7519-brn", "arcadyan,vgv7519", "lantiq,xway", "lantiq,vr9"; - model = "KPN Experiabox V8"; -}; - -&localbus { - nor@0 { - partitions { - partition@0 { - label = "Boot"; - reg = <0x00000 0x40000>; - read-only; - }; - - partition@50000 { - label = "Certificate"; - reg = <0x50000 0x10000>; - read-only; - }; - partition@60000 { - label = "Special_Area"; - reg = <0x60000 0x10000>; - read-only; - }; - - partition@70000 { - label = " Reserve_0"; - reg = <0x70000 0x10000>; - read-only; - }; - - partition@80000 { - label = "Code_Image_0"; - reg = <0x80000 0x780000>; - brnboot,root-id = <0x00>; - read-only; - }; - - partition@4000000 { - compatible = "brnboot,root-selector"; - label = "Primary_Setting"; - reg = <0x4000000 0x10000>; - read-only; - }; - - partition@4010000 { - label = "Configuration"; - reg = <0x4010000 0x60000>; - read-only; - }; - - partition@4070000 { - label = " Reserve_1"; - reg = <0x4070000 0x10000>; - read-only; - }; - - partition@4080000 { - label = "Code_Image_1"; - reg = <0x4080000 0x780000>; - brnboot,root-id = <0x01>; - read-only; - }; - }; - }; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VGV7519NOR.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VGV7519NOR.dts deleted file mode 100644 index 4bdf0bc753..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VGV7519NOR.dts +++ /dev/null @@ -1,29 +0,0 @@ -/dts-v1/; - -#include "VGV7519.dtsi" - -/ { - compatible = "arcadyan,vgv7519-nor", "arcadyan,vgv7519", "lantiq,xway", "lantiq,vr9"; - model = "KPN Experiabox V8"; -}; - -&localbus { - nor@0 { - partitions { - partition@0 { - label = "uboot"; - reg = <0x00000 0x40000>; - read-only; - }; - partition@60000 { - label = "uboot_env"; - reg = <0x60000 0x10000>; - read-only; - }; - partition@80000 { - label = "firmware"; - reg = <0x80000 0xf80000>; - }; - }; - }; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VR200.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VR200.dts deleted file mode 100644 index 74f666ddfd..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VR200.dts +++ /dev/null @@ -1,94 +0,0 @@ -/dts-v1/; - -#include "VR200.dtsi" - -/ { - compatible = "tplink,vr200", "lantiq,xway", "lantiq,vr9"; - model = "TP-LINK Archer VR200"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power; - led-failsafe = &power; - led-running = &power; - led-upgrade = &power; - - led-dsl = &dsl; - led-internet = &internet; - led-wifi = &wlan5g; - - led-usb = &led_usb; - led-usb2 = &led_usb; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - reset { - label = "reset"; - gpios = <&gpio 22 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - wifi { - label = "wifi"; - gpios = <&gpio 0 GPIO_ACTIVE_HIGH>; - linux,code = ; - linux,input-type = ; - }; - - wps { - label = "wps"; - gpios = <&gpio 2 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - led { - label = "led"; - gpios = <&gpio 39 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - power: power { - label = "vr200:blue:power"; - gpios = <&gpio 46 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - dsl: dsl { - label = "vr200:blue:dsl"; - gpios = <&gpio 4 GPIO_ACTIVE_LOW>; - }; - internet: internet { - label = "vr200:blue:internet"; - gpios = <&gpio 5 GPIO_ACTIVE_LOW>; - }; - led_usb: usb { - label = "vr200:blue:usb"; - gpios = <&gpio 25 GPIO_ACTIVE_LOW>; - }; - eth { - label = "vr200:blue:lan"; - gpios = <&gpio 40 GPIO_ACTIVE_LOW>; - }; - wlan { - label = "vr200:blue:wlan"; - gpios = <&gpio 24 GPIO_ACTIVE_LOW>; - }; - wlan5g: wifi { - label = "vr200:blue:wlan5g"; - gpios = <&gpio 20 GPIO_ACTIVE_LOW>; - }; - led_wps { - label = "vr200:blue:wps"; - gpios = <&gpio 44 GPIO_ACTIVE_LOW>; - }; - }; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VR200.dtsi b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VR200.dtsi deleted file mode 100644 index dcfa86125d..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VR200.dtsi +++ /dev/null @@ -1,219 +0,0 @@ -#include "vr9.dtsi" - -#include -#include - -/ { - memory@0 { - reg = <0x0 0x7f00000>; - }; - - usb_vbus: regulator-usb-vbus { - compatible = "regulator-fixed"; - - regulator-name = "USB_VBUS"; - - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - gpio = <&gpio 33 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -ð0 { - lan: interface@0 { - compatible = "lantiq,xrx200-pdi"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - mtd-mac-address = <&romfile 0xf100>; - lantiq,switch; - - ethernet@0 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <0>; - phy-mode = "rgmii"; - phy-handle = <&phy0>; - // gpios = <&gpio 42 GPIO_ACTIVE_LOW>; - }; - ethernet@5 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <5>; - phy-mode = "rgmii"; - phy-handle = <&phy5>; - }; - ethernet@2 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <2>; - phy-mode = "gmii"; - phy-handle = <&phy11>; - }; - ethernet@3 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <4>; - phy-mode = "gmii"; - phy-handle = <&phy13>; - }; - }; - - mdio@0 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "lantiq,xrx200-mdio"; - reg = <0>; - - phy0: ethernet-phy@0 { - reg = <0x0>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - phy5: ethernet-phy@5 { - reg = <0x5>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - phy11: ethernet-phy@11 { - reg = <0x11>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - phy13: ethernet-phy@13 { - reg = <0x13>; - compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; - }; - }; -}; - -&gphy0 { - lantiq,gphy-mode = ; -}; - -&gphy1 { - lantiq,gphy-mode = ; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - mdio { - lantiq,groups = "mdio"; - lantiq,function = "mdio"; - }; - gphy-leds { - lantiq,groups = "gphy0 led1", "gphy1 led1"; - lantiq,function = "gphy"; - lantiq,pull = <2>; - lantiq,open-drain = <0>; - lantiq,output = <1>; - }; - phy-rst { - lantiq,pins = "io42"; - lantiq,pull = <0>; - lantiq,open-drain = <0>; - lantiq,output = <1>; - }; - pcie-rst { - lantiq,pins = "io38"; - lantiq,pull = <0>; - lantiq,output = <1>; - }; - }; - pins_spi_default: pins_spi_default { - spi_in { - lantiq,groups = "spi_di"; - lantiq,function = "spi"; - }; - spi_out { - lantiq,groups = "spi_do", "spi_clk", - "spi_cs4"; - lantiq,function = "spi"; - lantiq,output = <1>; - }; - }; -}; - -&pci0 { - status = "okay"; - gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; -}; - -&spi { - status = "okay"; - - pinctrl-names = "default"; - pinctrl-0 = <&pins_spi_default>; - - m25p80@4 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "jedec,spi-nor"; - reg = <4 0>; - spi-max-frequency = <33250000>; - m25p,fast-read; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - reg = <0x0 0x20000>; - label = "u-boot"; - read-only; - }; - - partition@20000 { - reg = <0x20000 0xf90000>; - label = "firmware"; - }; - - partition@fb0000 { - reg = <0xfb0000 0x10000>; - label = "radioDECT"; - read-only; - }; - - partition@fc0000 { - reg = <0xfc0000 0x10000>; - label = "config"; - read-only; - }; - - romfile: partition@fd0000 { - reg = <0xfd0000 0x10000>; - label = "romfile"; - read-only; - }; - - partition@fe0000 { - reg = <0xfe0000 0x10000>; - label = "rom"; - read-only; - }; - - partition@ff0000 { - reg = <0xff0000 0x10000>; - label = "radio"; - read-only; - }; - }; - }; -}; - -&usb_phy0 { - status = "okay"; -}; - -&usb_phy1 { - status = "okay"; -}; - -&usb0 { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; - -&usb1 { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VR200v.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VR200v.dts deleted file mode 100644 index dc65dbfc36..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/VR200v.dts +++ /dev/null @@ -1,101 +0,0 @@ -/dts-v1/; - -#include "VR200.dtsi" - -/ { - compatible = "tplink,vr200v", "lantiq,xway", "lantiq,vr9"; - model = "TP-LINK Archer VR200v"; - - chosen { - bootargs = "console=ttyLTQ0,115200 mem=126M vpe1_load_addr=0x87e00000 vpe1_mem=2M maxvpes=1 maxtcs=1 nosmp"; - }; - - aliases { - led-boot = &power; - led-failsafe = &power; - led-running = &power; - led-upgrade = &power; - - led-dsl = &dsl; - led-internet = &internet; - led-wifi = &wlan5g; - - led-usb = &led_usb; - led-usb2 = &led_usb; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - reset { - label = "reset"; - gpios = <&gpio 22 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - wifi { - label = "wifi"; - gpios = <&gpio 0 GPIO_ACTIVE_HIGH>; - linux,code = ; - linux,input-type = ; - }; - - wps { - label = "wps"; - gpios = <&gpio 2 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - dect_paging { - label = "dect_paging"; - gpios = <&gpio 39 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - power: power { - label = "vr200v:blue:power"; - gpios = <&gpio 46 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - dsl: dsl { - label = "vr200v:blue:dsl"; - gpios = <&gpio 4 GPIO_ACTIVE_LOW>; - }; - internet: internet { - label = "vr200v:blue:internet"; - gpios = <&gpio 5 GPIO_ACTIVE_LOW>; - }; - led_usb: usb { - label = "vr200v:blue:usb"; - gpios = <&gpio 25 GPIO_ACTIVE_LOW>; - }; - eth { - label = "vr200v:blue:lan"; - gpios = <&gpio 40 GPIO_ACTIVE_LOW>; - }; - wlan { - label = "vr200v:blue:wlan"; - gpios = <&gpio 24 GPIO_ACTIVE_LOW>; - }; - wlan5g: wifi { - label = "vr200v:blue:wlan5g"; - gpios = <&gpio 20 GPIO_ACTIVE_LOW>; - }; - phone { - label = "vr200v:blue:phone"; - gpios = <&gpio 44 GPIO_ACTIVE_LOW>; - }; - }; -}; - -&vmmc { - status = "okay"; - gpios = <&gpio 30 GPIO_ACTIVE_HIGH //fxs relay - &gpio 31 GPIO_ACTIVE_HIGH //still unknown - &gpio 3 GPIO_ACTIVE_HIGH>; //reset_slic? -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/WBMR.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/WBMR.dts deleted file mode 100644 index 9759b311b7..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/WBMR.dts +++ /dev/null @@ -1,200 +0,0 @@ -/dts-v1/; - -#include "ar9.dtsi" - -#include - -/ { - compatible = "buffalo,wbmr-hp-g300h", "lantiq,xway", "lantiq,ar9"; - model = "Buffalo WBMR-HP-G300H"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power_green; - led-failsafe = &power_red; - led-running = &power_green; - led-upgrade = &power_green; - - led-dsl = &dsl; - led-internet = &online_green; - led-usb = &led_usb; - led-wifi = &wifi; - }; - - memory@0 { - reg = <0x0 0x4000000>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - wps { - label = "wps"; - gpios = <&gpio 0 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - reset { - label = "reset"; - gpios = <&gpio 37 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - eject { - label = "eject"; - gpios = <&gpio 34 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - movie { - label = "movie"; - gpios = <&gpio 22 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - - power_green: power { - label = "wbmr:green:power"; - gpios = <&gpio 1 GPIO_ACTIVE_LOW>; - default-state = "keep"; - }; - power_red: power2 { - label = "wbmr:red:power"; - gpios = <&gpio 5 GPIO_ACTIVE_LOW>; - }; - security { - label = "wbmr:yellow:security"; - gpios = <&gpio 14 GPIO_ACTIVE_LOW>; - }; - wifi: wifi { - label = "wbmr:green:wireless"; - gpios = <&gpio 15 GPIO_ACTIVE_LOW>; - }; - dsl: dsl { - label = "wbmr:green:dsl"; - gpios = <&gpio 16 GPIO_ACTIVE_LOW>; - }; - online_green: online { - label = "wbmr:green:internet"; - gpios = <&gpio 17 GPIO_ACTIVE_LOW>; - }; - online2 { - label = "wbmr:red:internet"; - gpios = <&gpio 18 GPIO_ACTIVE_LOW>; - }; - movie { - label = "wbmr:blue:movie"; - gpios = <&gpio 20 GPIO_ACTIVE_LOW>; - }; - led_usb: usb { - label = "wbmr:green:usb"; - gpios = <&gpio 28 GPIO_ACTIVE_LOW>; - default-state = "on"; - }; - }; - - usb_vbus: regulator-usb-vbus { - compatible = "regulator-fixed"; - - regulator-name = "USB_VBUS"; - - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - gpio = <&gpio 36 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - pci-in { - lantiq,groups = "req1"; - lantiq,output = <0>; - lantiq,open-drain = <1>; - lantiq,pull = <2>; - }; - pci-out { - lantiq,groups = "gnt1"; - lantiq,output = <1>; - lantiq,pull = <0>; - }; - pci_rst { - lantiq,pins = "io21"; - lantiq,pull = <0>; - lantiq,output = <1>; - }; - }; -}; - -&gsw { - phy-mode = "rgmii"; - mtd-mac-address = <&boardconfig 0x10024>; -}; - -&pci0 { - status = "okay"; -}; - -&localbus { - nor@0 { - compatible = "lantiq,nor"; - bank-width = <2>; - reg = <0 0x0 0x2000000>; - #address-cells = <1>; - #size-cells = <1>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "uboot"; - reg = <0x00000 0x40000>; - read-only; - }; - - partition@40000 { - label = "uboot_env"; - reg = <0x40000 0x20000>; - read-only; - }; - - partition@20000 { - label = "firmware"; - reg = <0x60000 0x1f20000>; - }; - - boardconfig: partition@1fc0000 { - label = "board"; - reg = <0x1fc0000 0x20000>; - read-only; - }; - - partition@1fe0000 { - label = "calibration"; - reg = <0x1fe0000 0x20000>; - read-only; - }; - }; - }; -}; - -&usb_phy0 { - status = "okay"; -}; - -&usb0 { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/WBMR300.dts b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/WBMR300.dts deleted file mode 100644 index 5dcf13912e..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/WBMR300.dts +++ /dev/null @@ -1,330 +0,0 @@ -/dts-v1/; - -#include "vr9.dtsi" - -#include -#include - -/ { - compatible = "buffalo,wbmr-300hpd", "lantiq,xway", "lantiq,vr9"; - model = "Buffalo WBMR-300HPD"; - - chosen { - bootargs = "console=ttyLTQ0,115200"; - }; - - aliases { - led-boot = &power_g; - led-failsafe = &diag_r; - led-running = &power_g; - led-upgrade = &power_g; - - led-dsl = &dsl; - led-internet = &router_g; - led-wifi = &wifi_g; - }; - - memory@0 { - reg = <0x0 0x4000000>; - }; - - gpio_poweroff { - compatible = "gpio-poweroff"; - gpios = <&gpio 6 GPIO_ACTIVE_LOW>; - }; - - gpio-keys-polled { - compatible = "gpio-keys-polled"; - #address-cells = <1>; - #size-cells = <0>; - poll-interval = <100>; - - power { - label = "power"; - gpios = <&gpio 5 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - reset { - label = "reset"; - gpios = <&gpio 7 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - wps { - label = "wps"; - gpios = <&gpio 31 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - auto { - label = "auto"; - gpios = <&gpio 48 GPIO_ACTIVE_HIGH>; - linux,code = ; - linux,input-type = ; - }; - - router { - label = "router"; - gpios = <&gpio 2 GPIO_ACTIVE_HIGH>; - linux,code = ; - linux,input-type = ; - }; - }; - - gpio-leds { - compatible = "gpio-leds"; - - diag_r: diag_r { - label = "wbmr300:red:diag"; - gpios = <&gpio 0 GPIO_ACTIVE_HIGH>; - default_state = "off"; - }; - - wifi_g: wifi_g { - label = "wbmr300:green:wifi"; - gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; - }; - - dsl: dsl { - label = "dsl"; - gpios = <&gpio 4 GPIO_ACTIVE_HIGH>; - }; - - router_y: router_y { - label = "wbmr300:yellow:router"; - gpios = <&gpio 8 GPIO_ACTIVE_HIGH>; - }; - - wifi_y: wifi_y { - label = "wbmr300:yellow:wifi"; - gpios = <&gpio 9 GPIO_ACTIVE_HIGH>; - }; - - lan1: lan1 { - label = "wbmr300:green:lan1"; - gpios = <&gpio 11 GPIO_ACTIVE_HIGH>; - }; - - wan: wan { - label = "wbmr300:green:wan"; - gpios = <&gpio 12 GPIO_ACTIVE_HIGH>; - }; - - lan3: lan3 { - label = "wbmr300:green:lan3"; - gpios = <&gpio 15 GPIO_ACTIVE_HIGH>; - }; - - lan2: lan2 { - label = "wbmr300:green:lan2"; - gpios = <&gpio 33 GPIO_ACTIVE_HIGH>; - }; - - internet_g: internet_g { - label = "wbmr300:green:internet"; - gpios = <&gpio 34 GPIO_ACTIVE_HIGH>; - }; - - internet_y: internet_y { - label = "wbmr300:yellow:internet"; - gpios = <&gpio 35 GPIO_ACTIVE_HIGH>; - }; - - router_g: router_g { - label = "wbmr300:green:router"; - gpios = <&gpio 36 GPIO_ACTIVE_HIGH>; - }; - - power_g: power_g { - label = "wbmr300:green:power"; - gpios = <&gpio 49 GPIO_ACTIVE_HIGH>; - }; - }; - - usb_vbus: regulator-usb-vbus { - compatible = "regulator-fixed"; - - regulator-name = "USB_VBUS"; - - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - - gpio = <&gpio 33 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; -}; - -ð0 { - lan: interface@0 { - compatible = "lantiq,xrx200-pdi"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - lantiq,switch; - - ethernet@1 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <4>; - phy-mode = "mii"; - phy-handle = <&phy13>; - }; - ethernet@2 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <5>; - phy-mode = "mii"; - phy-handle = <&phy14>; - }; - ethernet@3 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <2>; - phy-mode = "mii"; - phy-handle = <&phy11>; - }; - ethernet@4 { - compatible = "lantiq,xrx200-pdi-port"; - reg = <3>; - phy-mode = "mii"; - phy-handle = <&phy12>; - }; - }; - - mdio@0 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "lantiq,xrx200-mdio"; - reg = <0>; - - phy11: ethernet-phy@11 { - reg = <0x11>; - compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; - }; - phy12: ethernet-phy@12 { - reg = <0x12>; - compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; - }; - phy13: ethernet-phy@13 { - reg = <0x13>; - compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; - }; - phy14: ethernet-phy@14 { - reg = <0x14>; - compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; - }; - }; -}; - -&gphy0 { - lantiq,gphy-mode = ; -}; - -&gphy1 { - lantiq,gphy-mode = ; -}; - -&gpio { - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinmux { - mdio { - lantiq,groups = "mdio"; - lantiq,function = "mdio"; - }; - phy-rst { - lantiq,pins = "io42"; - lantiq,pull = <0>; - lantiq,open-drain = <0>; - lantiq,output = <1>; - }; - pcie-rst { - lantiq,pins = "io38"; - lantiq,pull = <0>; - lantiq,output = <1>; - }; - }; - pins_spi_default: pins_spi_default { - spi_in { - lantiq,groups = "spi_di"; - lantiq,function = "spi"; - }; - spi_out { - lantiq,groups = "spi_do", "spi_clk", - "spi_cs4"; - lantiq,function = "spi"; - lantiq,output = <1>; - }; - }; -}; - -&spi { - status = "okay"; - - pinctrl-names = "default"; - pinctrl-0 = <&pins_spi_default>; - - m25p80@4 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "jedec,spi-nor"; - reg = <4 0>; - spi-max-frequency = <20000000>; - - partition@0 { - reg = <0x0 0x10000>; - label = "u-boot"; - read-only; - }; - - partition@10000 { - reg = <0x10000 0x10000>; - label = "gphyfirmware"; - read-only; - }; - - partition@20000 { - reg = <0x20000 0x80000>; - label = "dsl_fw"; - }; - - partition@de0000 { - reg = <0xa0000 0xf40000>; - label = "firmware"; - }; - - partition@fe0000 { - reg = <0xfe0000 0x10000>; - label = "sysconfig"; - read-only; - }; - - partition@ff0000 { - reg = <0xff0000 0x2000>; - label = "ubootconfig"; - }; - - partition@ff3000 { - reg = <0xff3000 0x2000>; - label = "board_config"; - read-only; - }; - }; -}; - -&usb_phy0 { - status = "okay"; -}; - -&usb_phy1 { - status = "okay"; -}; - -&usb0 { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; - -&usb1 { - status = "okay"; - vbus-supply = <&usb_vbus>; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/amazonse.dtsi b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/amazonse.dtsi deleted file mode 100644 index f216adf36f..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/amazonse.dtsi +++ /dev/null @@ -1,204 +0,0 @@ -#include - -/ { - #address-cells = <1>; - #size-cells = <1>; - compatible = "lantiq,xway", "lantiq,ase"; - - aliases { - serial0 = &asc1; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - cpus { - cpu@0 { - compatible = "mips,mips4Kc"; - }; - }; - - memory@0 { - device_type = "memory"; - }; - - biu@1f800000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "lantiq,biu", "simple-bus"; - reg = <0x1f800000 0x800000>; - ranges = <0x0 0x1f800000 0x7fffff>; - - icu0: icu@80200 { - #interrupt-cells = <1>; - interrupt-controller; - compatible = "lantiq,icu"; - reg = <0x80200 0x28 - 0x80228 0x28 - 0x80250 0x28 - 0x80278 0x28 - 0x802a0 0x28>; - }; - - watchdog@803f0 { - compatible = "lantiq,wdt"; - reg = <0x803f0 0x10>; - }; - }; - - sram@1f000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "lantiq,sram", "simple-bus"; - reg = <0x1f000000 0x800000>; - ranges = <0x0 0x1f000000 0x7fffff>; - - eiu0: eiu@101000 { - #interrupt-cells = <1>; - interrupt-controller; - compatible = "lantiq,eiu-xway"; - reg = <0x101000 0x1000>; - interrupt-parent = <&icu0>; - lantiq,eiu-irqs = <29 30 31>; - }; - - pmu0: pmu@102000 { - compatible = "lantiq,pmu-xway"; - reg = <0x102000 0x1000>; - }; - - cgu0: cgu@103000 { - compatible = "lantiq,cgu-xway"; - reg = <0x103000 0x1000>; - #clock-cells = <1>; - }; - - rcu0: rcu@203000 { - compatible = "lantiq,ase-rcu", "simple-mfd", "syscon"; - reg = <0x203000 0x1000>; - ranges = <0x0 0x203000 0x100>; - big-endian; - - reset: reset-controller@10 { - compatible = "lantiq,danube-reset"; - reg = <0x10 4>, <0x14 4>; - - #reset-cells = <2>; - }; - - usb_phy: usb2-phy@18 { - compatible = "lantiq,ase-usb2-phy"; - reg = <0x18 4>; - status = "disabled"; - - resets = <&reset 4 4>; - reset-names = "ctrl"; - #phy-cells = <0>; - }; - - reboot@10 { - compatible = "syscon-reboot"; - reg = <0x10 4>; - - regmap = <&rcu0>; - offset = <0x10>; - mask = <0x40000000>; - }; - }; - }; - - fpi@10000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "lantiq,fpi", "simple-bus"; - ranges = <0x0 0x10000000 0xeefffff>; - reg = <0x10000000 0xef00000>; - - localbus: localbus@0 { - #address-cells = <2>; - #size-cells = <1>; - ranges = <0 0 0x0 0x3ffffff /* addrsel0 */ - 1 0 0x4000000 0x4000010>; /* addsel1 */ - compatible = "lantiq,localbus", "simple-bus"; - }; - - spi: spi@e100800 { - compatible = "lantiq,ase-spi"; - reg = <0xe100800 0x100>; - interrupt-parent = <&icu0>; - interrupts = <24 25 26>; - interrupt-names = "spi_rx", "spi_tx", "spi_err", - "spi_frm"; - #address-cells = <1>; - #size-cells = <1>; - status = "disabled"; - }; - - gptu@e100a00 { - compatible = "lantiq,gptu-xway"; - reg = <0xe100a00 0x100>; - interrupt-parent = <&icu0>; - interrupts = <33 34 35 36 37 38>; - }; - - gpio: pinmux@e100b10 { - compatible = "lantiq,ase-pinctrl"; - #gpio-cells = <2>; - gpio-controller; - reg = <0xe100b10 0xa0>; - }; - - asc1: serial@e100c00 { - compatible = "lantiq,asc"; - reg = <0xe100c00 0x400>; - interrupt-parent = <&icu0>; - interrupts = <72 74 75>; - }; - - mei@e116000 { - compatible = "lantiq,mei-xway"; - interrupt-parent = <&icu0>; - interrupts = <81>; - }; - - usb: usb@e101000 { - compatible = "lantiq,ase-usb"; - reg = <0xe101000 0x1000 - 0xe120000 0x3f000>; - interrupt-parent = <&icu0>; - interrupts = <39>; - dr_mode = "host"; - phys = <&usb_phy>; - phy-names = "usb2-phy"; - status = "disabled"; - }; - - dma0: dma@e104100 { - compatible = "lantiq,dma-xway"; - reg = <0xe104100 0x800>; - }; - - ebu0: ebu@e105300 { - compatible = "lantiq,ebu-xway"; - reg = <0xe105300 0x100>; - }; - - ppe@e234000 { - compatible = "lantiq,ppe-ase"; - interrupt-parent = <&icu0>; - interrupts = <85>; - }; - - gsw: etop@e180000 { - compatible = "lantiq,etop-xway"; - reg = <0xe180000 0x40000>; - interrupt-parent = <&icu0>; - interrupts = <105 109>; - }; - }; - - adsl { - compatible = "lantiq,adsl-ase"; - }; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ar9.dtsi b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ar9.dtsi deleted file mode 100644 index 48e0d95d63..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/ar9.dtsi +++ /dev/null @@ -1,268 +0,0 @@ -#include - -/ { - #address-cells = <1>; - #size-cells = <1>; - compatible = "lantiq,xway", "lantiq,ar9"; - - aliases { - serial0 = &asc1; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - cpus { - cpu@0 { - compatible = "mips,mips34K"; - }; - }; - - memory@0 { - device_type = "memory"; - }; - - biu@1f800000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "lantiq,biu", "simple-bus"; - reg = <0x1f800000 0x800000>; - ranges = <0x0 0x1f800000 0x7fffff>; - - icu0: icu@80200 { - #interrupt-cells = <1>; - interrupt-controller; - compatible = "lantiq,icu"; - reg = <0x80200 0x28 - 0x80228 0x28 - 0x80250 0x28 - 0x80278 0x28 - 0x802a0 0x28>; - }; - - watchdog@803f0 { - compatible = "lantiq,xrx100-wdt", "lantiq,xrx100-wdt"; - reg = <0x803f0 0x10>; - - regmap = <&rcu0>; - }; - }; - - sram@1f000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "lantiq,sram", "simple-bus"; - reg = <0x1f000000 0x800000>; - ranges = <0x0 0x1f000000 0x7fffff>; - - eiu0: eiu@101000 { - #interrupt-cells = <1>; - interrupt-controller; - compatible = "lantiq,eiu-xway"; - reg = <0x101000 0x1000>; - interrupt-parent = <&icu0>; - lantiq,eiu-irqs = <166 135 66 40 41 42>; - }; - - pmu0: pmu@102000 { - compatible = "lantiq,pmu-xway"; - reg = <0x102000 0x1000>; - }; - - cgu0: cgu@103000 { - compatible = "lantiq,cgu-xway"; - reg = <0x103000 0x1000>; - #clock-cells = <1>; - }; - - rcu0: rcu@203000 { - compatible = "lantiq,xrx100-rcu", "simple-mfd", "syscon"; - reg = <0x203000 0x1000>; - ranges = <0x0 0x203000 0x100>; - big-endian; - - reset: reset-controller@10 { - compatible = "lantiq,xrx100-reset", "lantiq,danube-reset"; - reg = <0x10 4>, <0x14 4>; - - #reset-cells = <2>; - }; - - usb_phy0: usb2-phy@18 { - compatible = "lantiq,xrx100-usb2-phy"; - reg = <0x18 4>; - status = "disabled"; - - resets = <&reset 4 4>; - reset-names = "ctrl"; - #phy-cells = <0>; - }; - - usb_phy1: usb2-phy@34 { - compatible = "lantiq,xrx100-usb2-phy"; - reg = <0x34 4>; - status = "disabled"; - - resets = <&reset 28 28>; - reset-names = "ctrl"; - #phy-cells = <0>; - }; - - reboot@10 { - compatible = "syscon-reboot"; - reg = <0x10 4>; - - regmap = <&rcu0>; - offset = <0x10>; - mask = <0x40000000>; - }; - }; - }; - - fpi@10000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "lantiq,fpi", "simple-bus"; - ranges = <0x0 0x10000000 0xeefffff>; - reg = <0x10000000 0xef00000>; - - localbus: localbus@0 { - #address-cells = <2>; - #size-cells = <1>; - ranges = <0 0 0x0 0x3ffffff /* addrsel0 */ - 1 0 0x4000000 0x4000010>; /* addsel1 */ - compatible = "lantiq,localbus", "simple-bus"; - }; - - gptu@e100a00 { - compatible = "lantiq,gptu-xway"; - reg = <0xe100a00 0x100>; - interrupt-parent = <&icu0>; - interrupts = <126 127 128 129 130 131>; - }; - - asc0: serial@e100400 { - compatible = "lantiq,asc"; - reg = <0xe100400 0x400>; - interrupt-parent = <&icu0>; - interrupts = <104 105 106>; - status = "disabled"; - }; - - spi: spi@e100800 { - compatible = "lantiq,xrx100-spi"; - reg = <0xe100800 0x100>; - interrupt-parent = <&icu0>; - interrupts = <22 23 24>; - interrupt-names = "spi_rx", "spi_tx", "spi_err", - "spi_frm"; - #address-cells = <1>; - #size-cells = <1>; - status = "disabled"; - }; - - gpio: pinmux@e100b10 { - compatible = "lantiq,xrx100-pinctrl"; - #gpio-cells = <2>; - gpio-controller; - reg = <0xe100b10 0xa0>; - }; - - stp: stp@e100bb0 { - #gpio-cells = <2>; - compatible = "lantiq,gpio-stp-xway"; - gpio-controller; - reg = <0xe100bb0 0x40>; - status = "disabled"; - }; - - asc1: serial@e100c00 { - compatible = "lantiq,asc"; - reg = <0xe100c00 0x400>; - interrupt-parent = <&icu0>; - interrupts = <112 113 114>; - }; - - usb0: usb@e101000 { - compatible = "lantiq,arx100-usb"; - reg = <0xe101000 0x1000 - 0xe120000 0x3f000>; - interrupt-parent = <&icu0>; - interrupts = <62 91>; - dr_mode = "host"; - phys = <&usb_phy0>; - phy-names = "usb2-phy"; - status = "disabled"; - }; - - usb1: usb@e106000 { - compatible = "lantiq,arx100-usb"; - reg = <0xe106000 0x1000 - 0xe1e0000 0x3f000>; - interrupt-parent = <&icu0>; - interrupts = <91>; - dr_mode = "host"; - phys = <&usb_phy1>; - phy-names = "usb2-phy"; - status = "disabled"; - }; - - deu@e103100 { - compatible = "lantiq,deu-arx100"; - reg = <0xe103100 0xf00>; - }; - - dma0: dma@e104100 { - compatible = "lantiq,dma-xway"; - reg = <0xe104100 0x800>; - }; - - ebu0: ebu@e105300 { - compatible = "lantiq,ebu-xway"; - reg = <0xe105300 0x100>; - }; - - mei@e116000 { - compatible = "lantiq,mei-xway"; - interrupt-parent = <&icu0>; - interrupts = <63>; - }; - - gsw: etop@e180000 { - compatible = "lantiq,etop-xway"; - reg = <0xe180000 0x40000 - 0xe108000 0x200>; - interrupt-parent = <&icu0>; - interrupts = <73 72>; - mac-address = [ 00 11 22 33 44 55 ]; - }; - - ppe@e234000 { - compatible = "lantiq,ppe-arx100"; - interrupt-parent = <&icu0>; - interrupts = <96>; - }; - - pci0: pci@e105400 { - status = "disabled"; - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - compatible = "lantiq,pci-xway"; - bus-range = <0x0 0x0>; - ranges = <0x2000000 0 0x8000000 0x8000000 0 0x2000000 /* pci memory */ - 0x1000000 0 0x00000000 0xae00000 0 0x200000>; /* io space */ - reg = <0x7000000 0x8000 /* config space */ - 0xe105400 0x400>; /* pci bridge */ - lantiq,bus-clock = <33333333>; - interrupt-map-mask = <0xf800 0x0 0x0 0x7>; - interrupt-map = <0x7000 0 0 1 &icu0 30 1>; - req-mask = <0x1>; - }; - }; - - adsl { - compatible = "lantiq,adsl-arx100"; - }; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/danube.dtsi b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/danube.dtsi deleted file mode 100644 index af4c795af2..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/danube.dtsi +++ /dev/null @@ -1,252 +0,0 @@ -#include - -/ { - #address-cells = <1>; - #size-cells = <1>; - compatible = "lantiq,xway", "lantiq,danube"; - - aliases { - serial0 = &asc1; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - cpus { - cpu@0 { - compatible = "mips,mips24Kc"; - }; - }; - - memory@0 { - device_type = "memory"; - }; - - biu@1f800000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "lantiq,biu", "simple-bus"; - reg = <0x1f800000 0x800000>; - ranges = <0x0 0x1f800000 0x7fffff>; - - icu0: icu@80200 { - #interrupt-cells = <1>; - interrupt-controller; - compatible = "lantiq,icu"; - reg = <0x80200 0x28 - 0x80228 0x28 - 0x80250 0x28 - 0x80278 0x28 - 0x802a0 0x28>; - }; - - watchdog@803f0 { - compatible = "lantiq,wdt"; - reg = <0x803f0 0x10>; - }; - }; - - sram@1f000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "lantiq,sram", "simple-bus"; - reg = <0x1f000000 0x800000>; - ranges = <0x0 0x1f000000 0x7fffff>; - - eiu0: eiu@101000 { - #interrupt-cells = <1>; - interrupt-controller; - compatible = "lantiq,eiu-xway"; - reg = <0x101000 0x1000>; - interrupt-parent = <&icu0>; - lantiq,eiu-irqs = <166 135 66>; - }; - - pmu0: pmu@102000 { - compatible = "lantiq,pmu-xway"; - reg = <0x102000 0x1000>; - }; - - cgu0: cgu@103000 { - compatible = "lantiq,cgu-xway"; - reg = <0x103000 0x1000>; - #clock-cells = <1>; - }; - - vmmc: vmmc@107000 { - status = "disabled"; - compatible = "lantiq,vmmc-xway"; - reg = <0x103000 0x400>; - interrupt-parent = <&icu0>; - interrupts = <150 151 152 153 154 155>; - }; - - rcu0: rcu@203000 { - compatible = "lantiq,danube-rcu", "simple-mfd", "syscon"; - reg = <0x203000 0x1000>; - ranges = <0x0 0x203000 0x100>; - big-endian; - - reset: reset-controller@10 { - compatible = "lantiq,danube-reset"; - reg = <0x10 4>, <0x14 4>; - - #reset-cells = <2>; - }; - - usb_phy: usb2-phy@18 { - compatible = "lantiq,danube-usb2-phy"; - reg = <0x18 4>; - status = "disabled"; - - resets = <&reset 4 4>; - reset-names = "ctrl"; - #phy-cells = <0>; - }; - - reboot@10 { - compatible = "syscon-reboot"; - reg = <0x10 4>; - - regmap = <&rcu0>; - offset = <0x10>; - mask = <0x40000000>; - }; - }; - }; - - fpi@10000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "lantiq,fpi", "simple-bus"; - ranges = <0x0 0x10000000 0xeefffff>; - reg = <0x10000000 0xef00000>; - - localbus: localbus@0 { - #address-cells = <2>; - #size-cells = <1>; - ranges = <0 0 0x0 0x3ffffff /* addrsel0 */ - 1 0 0x4000000 0x4000010>; /* addsel1 */ - compatible = "lantiq,localbus", "simple-bus"; - - gpiomm: gpiomm@1 { - compatible = "lantiq,gpio-mm"; - reg = <1 0x0 0x10 >; - #address-cells = <1>; - #size-cells = <1>; - #gpio-cells = <2>; - gpio-controller; - status = "disabled"; - }; - }; - - gptu@e100a00 { - compatible = "lantiq,gptu-xway"; - reg = <0xe100a00 0x100>; - interrupt-parent = <&icu0>; - interrupts = <126 127 128 129 130 131>; - }; - - gpios: stp@e100bb0 { - #gpio-cells = <2>; - compatible = "lantiq,gpio-stp-xway"; - gpio-controller; - reg = <0xe100bb0 0x40>; - lantiq,shadow = <0xfff>; - lantiq,groups = <0x3>; - status = "disabled"; - }; - - asc0: serial@e100400 { - compatible = "lantiq,asc"; - reg = <0xe100400 0x400>; - interrupt-parent = <&icu0>; - interrupts = <104 105 106>; - status = "disabled"; - }; - - gpio: pinmux@e100b10 { - compatible = "lantiq,danube-pinctrl"; - #gpio-cells = <2>; - gpio-controller; - reg = <0xe100b10 0xa0>; - }; - - asc1: serial@e100c00 { - compatible = "lantiq,asc"; - reg = <0xe100c00 0x400>; - interrupt-parent = <&icu0>; - interrupts = <112 113 114>; - }; - - usb: usb@e101000 { - compatible = "lantiq,danube-usb"; - reg = <0xe101000 0x1000 - 0xe120000 0x3f000>; - interrupt-parent = <&icu0>; - interrupts = <62>; - dr_mode = "host"; - phys = <&usb_phy>; - phy-names = "usb2-phy"; - status = "disabled"; - }; - - deu@e103100 { - compatible = "lantiq,deu-danube"; - reg = <0xe103100 0xf00>; - }; - - dma0: dma@e104100 { - compatible = "lantiq,dma-xway"; - reg = <0xe104100 0x800>; - }; - - ebu0: ebu@e105300 { - compatible = "lantiq,ebu-xway"; - reg = <0xe105300 0x100>; - }; - - mei@e116000 { - compatible = "lantiq,mei-xway"; - interrupt-parent = <&icu0>; - interrupts = <63>; - }; - - gsw: etop@e180000 { - compatible = "lantiq,etop-xway"; - reg = <0xe180000 0x40000>; - interrupt-parent = <&icu0>; - interrupts = <73 78>; - mac-address = [ 00 11 22 33 44 55 ]; - }; - - ppe@e234000 { - compatible = "lantiq,ppe-danube"; - interrupt-parent = <&icu0>; - interrupts = <96>; - }; - - pci0: pci@e105400 { - status = "disabled"; - - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - compatible = "lantiq,pci-xway"; - bus-range = <0x0 0x0>; - ranges = <0x2000000 0 0x8000000 0x8000000 0 0x2000000 /* pci memory */ - 0x1000000 0 0x00000000 0xae00000 0 0x200000>; /* io space */ - reg = <0x7000000 0x8000 /* config space */ - 0xe105400 0x400>; /* pci bridge */ - lantiq,bus-clock = <33333333>; - interrupt-map-mask = <0xf800 0x0 0x0 0x7>; - interrupt-map = <0x7000 0 0 1 &icu0 30 1>; /* slot 14, irq 30 */ - req-mask = <0x1>; /* GNT1 */ - }; - }; - - adsl { - compatible = "lantiq,adsl-danube"; - }; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/falcon-sflash-16M.dtsi b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/falcon-sflash-16M.dtsi deleted file mode 100644 index d95acc21ef..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/falcon-sflash-16M.dtsi +++ /dev/null @@ -1,37 +0,0 @@ - -&ebu_cs0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "lantiq,sflash-falcon", "simple-bus"; - - flash@0 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "spansion,s25fl129p0", "spansion,s25fl129p1"; - reg = <0 0>; - linux,mtd-name = "sflash"; - spi-max-frequency = <80000000>; - m25p,fast-read; - - partition@0 { - reg = <0x0 0x40000>; - label = "uboot"; - read-only; - }; - - partition@40000 { - reg = <0x40000 0x80000>; - label = "uboot_env"; - }; - - partition@C0000 { - reg = <0xC0000 0x740000>; - label = "image0"; - }; - - partition@800000 { - reg = <0x800000 0x800000>; - label = "image1"; - }; - }; -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/falcon.dtsi b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/falcon.dtsi deleted file mode 100644 index 98f71819a2..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/falcon.dtsi +++ /dev/null @@ -1,392 +0,0 @@ -/ { - #address-cells = <1>; - #size-cells = <1>; - compatible = "lantiq,falcon"; - - cpus { - cpu@0 { - compatible = "mips,mips34kc"; - }; - }; - - aliases { - serial0 = &serial0; - serial1 = &serial1; - gpio0 = &gpio0; - gpio1 = &gpio1; - gpio2 = &gpio2; - gpio3 = &gpio3; - gpio4 = &gpio4; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - clocks { - compatible = "simple-bus"; - - cpu_clk: cpu { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <400000000>; - clock-output-names = "cpu"; - }; - - io_clk: io { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <200000000>; - clock-output-names = "io"; - }; - - fpi_clk: fpi { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <100000000>; - clock-output-names = "fpi"; - }; - }; - - ebu_cs0: localbus@10000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "lantiq,localbus", "simple-bus"; - reg = <0x10000000 0x4000000>; - ranges = <0x0 0x10000000 0x4000000>; - }; - ebu_cs1: localbus@14000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "lantiq,localbus", "simple-bus"; - reg = <0x14000000 0x4000000>; - ranges = <0x0 0x14000000 0x4000000>; - }; - - ebu@18000000 { - compatible = "lantiq,ebu-falcon"; - reg = <0x18000000 0x100>; - }; - - sbs2@1D000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "lantiq,sysb2", "simple-bus"; - reg = <0x1D000000 0x1000000>; - ranges = <0x0 0x1D000000 0x1000000>; - - clock_sysgpe: clock-controller@700000 { - compatible = "lantiq,sysgpe-falcon"; - reg = <0x700000 0x100>; - #clock-cells = <1>; - }; - - mps@4000 { - compatible = "lantiq,mps-falcon", "lantiq,mps-xrx100"; - reg = <0x4000 0x1000>; - interrupt-parent = <&icu0>; - interrupts = <154 155>; - lantiq,mbx = <&mpsmbx>; - }; - - gpio0: gpio@810000 { - compatible = "lantiq,falcon-gpio"; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - interrupt-parent = <&icu0>; - interrupts = <44>; - reg = <0x810000 0x80>; - clocks = <&clock_syseth 16>; - }; - - gpio2: gpio@810100 { - compatible = "lantiq,falcon-gpio"; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - interrupt-parent = <&icu0>; - interrupts = <46>; - reg = <0x810100 0x80>; - clocks = <&clock_syseth 17>; - }; - - clock_syseth: clock-controller@B00000 { - compatible = "lantiq,syseth-falcon"; - reg = <0xB00000 0x100>; - #clock-cells = <1>; - }; - - pad@B01000 { - compatible = "lantiq,pad-falcon"; - reg = <0xB01000 0x100>; - lantiq,bank = <0>; - clocks = <&clock_syseth 20>; - }; - - pad@B02000 { - compatible = "lantiq,pad-falcon"; - reg = <0xB02000 0x100>; - lantiq,bank = <2>; - clocks = <&clock_syseth 21>; - }; - }; - - fpi@1E000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "lantiq,fpi", "simple-bus"; - reg = <0x1E000000 0x1000000>; - ranges = <0x0 0x1E000000 0x1000000>; - - serial1: serial@100B00 { - status = "disabled"; - compatible = "lantiq,asc"; - reg = <0x100B00 0x100>; - interrupt-parent = <&icu0>; - interrupts = <112 113 114>; - line = <1>; - pinctrl-names = "default"; - pinctrl-0 = <&asc1_pins>; - clocks = <&clock_sys1 11>; - }; - - serial0: serial@100C00 { - compatible = "lantiq,asc"; - reg = <0x100C00 0x100>; - interrupt-parent = <&icu0>; - interrupts = <104 105 106>; - line = <0>; - pinctrl-names = "default"; - pinctrl-0 = <&asc0_pins>; - clocks = <&clock_sys1 12>; - }; - - spi: spi@100D00 { - status = "disabled"; - compatible = "lantiq,falcon-spi", "lantiq,xrx100-spi", "lantiq,spi-lantiq-ssc"; - interrupts = <22 23 24 25>; - interrupt-names = "spi_tx", "spi_rx", "spi_err", "spi_frm"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x100D00 0x100>; - interrupt-parent = <&icu0>; - clocks = <&clock_sys1 13>; - base_cs = <1>; - num_cs = <2>; - }; - - gptc@100E00 { - compatible = "lantiq,gptc-falcon"; - reg = <0x100E00 0x100>; - }; - - i2c: i2c@200000 { - status = "disabled"; - #address-cells = <1>; - #size-cells = <0>; - compatible = "lantiq,lantiq-i2c"; - reg = <0x200000 0x10000>; - interrupt-parent = <&icu0>; - interrupts = <18 19 20 21>; - gpios = <&gpio1 7 0 &gpio1 8 0>; - pinctrl-names = "default"; - pinctrl-0 = <&i2c_pins>; - clocks = <&clock_sys1 14>; - }; - - gpio1: gpio@800100 { - compatible = "lantiq,falcon-gpio"; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - interrupt-parent = <&icu0>; - interrupts = <45>; - reg = <0x800100 0x100>; - clocks = <&clock_sys1 16>; - }; - - gpio3: gpio@800200 { - compatible = "lantiq,falcon-gpio"; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - interrupt-parent = <&icu0>; - interrupts = <47>; - reg = <0x800200 0x100>; - clocks = <&clock_sys1 17>; - }; - - gpio4: gpio@800300 { - compatible = "lantiq,falcon-gpio"; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - interrupt-parent = <&icu0>; - interrupts = <48>; - reg = <0x800300 0x100>; - clocks = <&clock_sys1 18>; - }; - - pad@800400 { - compatible = "lantiq,pad-falcon"; - reg = <0x800400 0x100>; - lantiq,bank = <1>; - clocks = <&clock_sys1 20>; - }; - - pad@800500 { - compatible = "lantiq,pad-falcon"; - reg = <0x800500 0x100>; - lantiq,bank = <3>; - clocks = <&clock_sys1 21>; - }; - - pad@800600 { - compatible = "lantiq,pad-falcon"; - reg = <0x800600 0x100>; - lantiq,bank = <4>; - clocks = <&clock_sys1 22>; - }; - - status@802000 { - compatible = "lantiq,status-falcon"; - reg = <0x802000 0x80>; - }; - - clock_sys1: clock-controller@F00000 { - compatible = "lantiq,sys1-falcon"; - reg = <0xF00000 0x100>; - #clock-cells = <1>; - }; - }; - - sbs0@1F000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "simple-bus"; - reg = <0x1F000000 0x400000>; - ranges = <0x0 0x1F000000 0x400000>; - - mpsmbx: mpsmbx@200000 { - reg = <0x200000 0x200>; - }; - }; - - sbs1@1F700000 { - - }; - - biu@1F800000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "lantiq,biu", "simple-bus"; - reg = <0x1F800000 0x800000>; - ranges = <0x0 0x1F800000 0x800000>; - - icu0: icu@80200 { - #interrupt-cells = <1>; - interrupt-controller; - compatible = "lantiq,icu"; - reg = <0x80200 0x28 - 0x80228 0x28 - 0x80250 0x28 - 0x80278 0x28 - 0x802a0 0x28>; - }; - - watchdog@803F0 { - compatible = "lantiq,wdt"; - reg = <0x803F0 0x10>; - clocks = <&io_clk>; /* currently no effect */ - }; - }; - - pinctrl { - compatible = "lantiq,pinctrl-falcon"; - pinctrl-names = "default"; - pinctrl-0 = <&state_default>; - - state_default: pinctrl0 { - /*ntr { - lantiq,groups = "ntr8k"; - lantiq,function = "ntr"; - };*/ - hrst { - lantiq,groups = "hrst"; - lantiq,function = "rst"; - }; - }; - - asc0_pins: asc0 { - asc0 { - lantiq,groups = "asc0"; - lantiq,function = "asc"; - }; - }; - asc1_pins: asc1 { - asc1 { - lantiq,groups = "asc1"; - lantiq,function = "asc"; - }; - }; - i2c_pins: i2c { - i2c { - lantiq,groups = "i2c"; - lantiq,function = "i2c"; - }; - }; - bootled_pins: bootled { - bootled { - lantiq,groups = "bootled"; - lantiq,function = "led"; - }; - }; - ntr_ntr8k: ntr8k { - ntr8k { - lantiq,groups = "ntr8k"; - lantiq,function = "ntr"; - }; - }; - ntr_pps: pps { - pps { - lantiq,groups = "pps"; - lantiq,function = "ntr"; - }; - }; - ntr_gpio: gpio { - gpio { - lantiq,pins = "io5"; - lantiq,mux = <1>; - lantiq,output = <0>; - }; - }; - slic_pins: slic { - slic { - lantiq,groups = "slic"; - lantiq,function = "slic"; - }; - }; - }; - - pinselect-ntr { - compatible = "lantiq,onu-ntr","lantiq,pinselect-ntr"; - pinctrl-names = "ntr8k", "pps", "gpio"; - pinctrl-0 = <&ntr_ntr8k>; - pinctrl-1 = <&ntr_pps>; - pinctrl-2 = <&ntr_gpio>; - }; - - pinselect-asc1 { - compatible = "lantiq,onu-asc1","lantiq,pinselect-asc1"; - pinctrl-names = "default", "asc1"; - pinctrl-0 = <&slic_pins>; - pinctrl-1 = <&asc1_pins>; - }; - -}; diff --git a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/vr9.dtsi b/target/linux/lantiq/files-4.14/arch/mips/boot/dts/vr9.dtsi deleted file mode 100644 index 6e8f0d1300..0000000000 --- a/target/linux/lantiq/files-4.14/arch/mips/boot/dts/vr9.dtsi +++ /dev/null @@ -1,341 +0,0 @@ -#include - -/ { - #address-cells = <1>; - #size-cells = <1>; - compatible = "lantiq,xway", "lantiq,vr9"; - - aliases { - serial0 = &asc1; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - cpus { - cpu@0 { - compatible = "mips,mips34Kc"; - }; - }; - - memory@0 { - device_type = "memory"; - }; - - cputemp@0 { - compatible = "lantiq,cputemp"; - }; - - biu@1f800000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "lantiq,biu", "simple-bus"; - reg = <0x1f800000 0x800000>; - ranges = <0x0 0x1f800000 0x7fffff>; - - icu0: icu@80200 { - #interrupt-cells = <1>; - interrupt-controller; - compatible = "lantiq,icu"; - reg = <0x80200 0x28 - 0x80228 0x28 - 0x80250 0x28 - 0x80278 0x28 - 0x802a0 0x28>; - }; - - watchdog@803f0 { - compatible = "lantiq,xrx100-wdt", "lantiq,xrx100-wdt"; - reg = <0x803f0 0x10>; - - regmap = <&rcu0>; - }; - }; - - sram@1f000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "lantiq,sram", "simple-bus"; - reg = <0x1f000000 0x800000>; - ranges = <0x0 0x1f000000 0x7fffff>; - - eiu0: eiu@101000 { - #interrupt-cells = <1>; - interrupt-controller; - compatible = "lantiq,eiu-xway"; - reg = <0x101000 0x1000>; - interrupt-parent = <&icu0>; - lantiq,eiu-irqs = <166 135 66 40 41 42>; - }; - - pmu0: pmu@102000 { - compatible = "lantiq,pmu-xway"; - reg = <0x102000 0x1000>; - }; - - cgu0: cgu@103000 { - compatible = "lantiq,cgu-xway"; - reg = <0x103000 0x1000>; - }; - - dcdc@106a00 { - compatible = "lantiq,dcdc-xrx200"; - reg = <0x106a00 0x200>; - }; - - vmmc: vmmc@103000 { - status = "disabled"; - compatible = "lantiq,vmmc-xway"; - reg = <0x103000 0x400>; - interrupt-parent = <&icu0>; - interrupts = <150 151 152 153 154 155>; - }; - - rcu0: rcu@203000 { - compatible = "lantiq,xrx200-rcu", "simple-mfd", "syscon"; - reg = <0x203000 0x100>; - ranges = <0x0 0x203000 0x100>; - big-endian; - - gphy0: gphy@20 { - compatible = "lantiq,xrx200-gphy"; - reg = <0x20 0x4>; - - resets = <&reset0 31 30>, <&reset1 7 7>; - reset-names = "gphy", "gphy2"; - }; - - gphy1: gphy@68 { - compatible = "lantiq,xrx200-gphy"; - reg = <0x68 0x4>; - - resets = <&reset0 29 28>, <&reset1 6 6>; - reset-names = "gphy", "gphy2"; - }; - - reset0: reset-controller@10 { - compatible = "lantiq,xrx200-reset"; - reg = <0x10 4>, <0x14 4>; - - #reset-cells = <2>; - }; - - reset1: reset-controller@48 { - compatible = "lantiq,xrx200-reset"; - reg = <0x48 4>, <0x24 4>; - - #reset-cells = <2>; - }; - - usb_phy0: usb2-phy@18 { - compatible = "lantiq,xrx200-usb2-phy"; - reg = <0x18 4>, <0x38 4>; - status = "disabled"; - - resets = <&reset1 4 4>, <&reset0 4 4>; - reset-names = "phy", "ctrl"; - #phy-cells = <0>; - }; - - usb_phy1: usb2-phy@34 { - compatible = "lantiq,xrx200-usb2-phy"; - reg = <0x34 4>, <0x3c 4>; - status = "disabled"; - - resets = <&reset1 5 5>, <&reset0 4 4>; - reset-names = "phy", "ctrl"; - #phy-cells = <0>; - }; - - reboot@10 { - compatible = "syscon-reboot"; - reg = <0x10 4>; - - regmap = <&rcu0>; - offset = <0x10>; - mask = <0xe0000000>; - }; - }; - }; - - fpi@10000000 { - compatible = "lantiq,xrx200-fpi", "simple-bus"; - ranges = <0x0 0x10000000 0xf000000>; - reg = <0x1f400000 0x1000>, - <0x10000000 0xf000000>; - regmap = <&rcu0>; - offset-endianness = <0x4c>; - #address-cells = <1>; - #size-cells = <1>; - - localbus: localbus@0 { - #address-cells = <2>; - #size-cells = <1>; - ranges = <0 0 0x0 0x3ffffff /* addrsel0 */ - 1 0 0x4000000 0x4000010>; /* addsel1 */ - compatible = "lantiq,localbus", "simple-bus"; - }; - - gptu@e100a00 { - compatible = "lantiq,gptu-xway"; - reg = <0xe100a00 0x100>; - interrupt-parent = <&icu0>; - interrupts = <126 127 128 129 130 131>; - }; - - usif: usif@da00000 { - compatible = "lantiq,usif"; - reg = <0xda00000 0x1000000>; - interrupt-parent = <&icu0>; - interrupts = <29 125 107 108 109 110>; - status = "disabled"; - }; - - spi: spi@e100800 { - compatible = "lantiq,xrx200-spi", "lantiq,xrx100-spi"; - reg = <0xe100800 0x100>; - interrupt-parent = <&icu0>; - interrupts = <22 23 24>; - interrupt-names = "spi_rx", "spi_tx", "spi_err", - "spi_frm"; - #address-cells = <1>; - #size-cells = <1>; - status = "disabled"; - }; - - gpio: pinmux@e100b10 { - compatible = "lantiq,xrx200-pinctrl"; - #gpio-cells = <2>; - gpio-controller; - reg = <0xe100b10 0xa0>; - }; - - stp: stp@e100bb0 { - status = "disabled"; - compatible = "lantiq,gpio-stp-xway"; - reg = <0xe100bb0 0x40>; - #gpio-cells = <2>; - gpio-controller; - - lantiq,shadow = <0xffffff>; - lantiq,groups = <0x7>; - lantiq,dsl = <0x0>; - lantiq,phy1 = <0x0>; - lantiq,phy2 = <0x0>; - }; - - asc1: serial@e100c00 { - compatible = "lantiq,asc"; - reg = <0xe100c00 0x400>; - interrupt-parent = <&icu0>; - interrupts = <112 113 114>; - }; - - deu@e103100 { - compatible = "lantiq,deu-xrx200"; - reg = <0xe103100 0xf00>; - }; - - dma0: dma@e104100 { - compatible = "lantiq,dma-xway"; - reg = <0xe104100 0x800>; - }; - - ebu0: ebu@e105300 { - compatible = "lantiq,ebu-xway"; - reg = <0xe105300 0x100>; - }; - - usb0: usb@e101000 { - status = "disabled"; - compatible = "lantiq,xrx200-usb"; - reg = <0xe101000 0x1000 - 0xe120000 0x3f000>; - interrupt-parent = <&icu0>; - interrupts = <62 91>; - dr_mode = "host"; - phys = <&usb_phy0>; - phy-names = "usb2-phy"; - }; - - usb1: usb@e106000 { - status = "disabled"; - compatible = "lantiq,xrx200-usb"; - reg = <0xe106000 0x1000>; - interrupt-parent = <&icu0>; - interrupts = <91>; - dr_mode = "host"; - phys = <&usb_phy1>; - phy-names = "usb2-phy"; - }; - - eth0: eth@e108000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "lantiq,xrx200-net"; - reg = < 0xe108000 0x3000 /* switch */ - 0xe10b100 0x70 /* mdio */ - 0xe10b1d8 0x30 /* mii */ - 0xe10b308 0x30 /* pmac */ - >; - interrupt-parent = <&icu0>; - interrupts = <75 73 72>; - resets = <&reset0 21 16>, <&reset0 8 8>; - reset-names = "switch", "ppe"; - lantiq,phys = <&gphy0>, <&gphy1>; - }; - - mei@e116000 { - compatible = "lantiq,mei-xrx200"; - reg = <0xe116000 0x9c>; - interrupt-parent = <&icu0>; - interrupts = <63>; - }; - - ppe@e234000 { - compatible = "lantiq,ppe-xrx200"; - interrupt-parent = <&icu0>; - interrupts = <96>; - resets = <&reset0 3 3>, <&reset0 11 11>, <&reset0 23 23>; - reset-names = "dsp", "dfe", "tc"; - }; - - pcie0: pcie@d900000 { - compatible = "lantiq,pcie-xrx200"; - - #interrupt-cells = <1>; - #size-cells = <2>; - #address-cells = <3>; - - interrupt-parent = <&icu0>; - interrupts = <161 144>; - - device_type = "pci"; - - gpio-reset = <&gpio 38 GPIO_ACTIVE_HIGH>; - }; - - pci0: pci@e105400 { - status = "disabled"; - - #address-cells = <3>; - #size-cells = <2>; - #interrupt-cells = <1>; - compatible = "lantiq,pci-xway"; - bus-range = <0x0 0x0>; - ranges = <0x2000000 0 0x8000000 0x8000000 0 0x2000000 /* pci memory */ - 0x1000000 0 0x00000000 0xae00000 0 0x200000>; /* io space */ - reg = <0x7000000 0x8000 /* config space */ - 0xe105400 0x400>; /* pci bridge */ - lantiq,bus-clock = <33333333>; - interrupt-map-mask = <0xf800 0x0 0x0 0x7>; - interrupt-map = <0x7000 0 0 1 &icu0 30 1>; /* slot 14, irq 30 */ - req-mask = <0x1>; /* GNT1 */ - }; - }; - - vdsl { - compatible = "lantiq,vdsl-vrx200"; - }; -}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/ACMP252.dts b/target/linux/lantiq/files/arch/mips/boot/dts/ACMP252.dts new file mode 100644 index 0000000000..5a2d867196 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/ACMP252.dts @@ -0,0 +1,114 @@ +/dts-v1/; + +#include "danube.dtsi" + +/ { + compatible = "audiocodes,mp-252", "lantiq,xway", "lantiq,danube"; + model = "AudioCodes MediaPack MP-252"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + memory@0 { + reg = <0x0 0x4000000>; + }; + + usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio 3 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + exin { + lantiq,groups = "exin1"; + lantiq,function = "exin"; + }; + pci { + lantiq,groups = "gnt1", "req1"; + lantiq,function = "pci"; + }; + }; +}; + +&gsw { + phy-mode = "rmii"; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x2000000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x0 0x20000>; + read-only; + }; + + partition@20000 { + label = "uboot_env"; + reg = <0x20000 0x20000>; + }; + + partition@40000 { + label = "boardconfig"; + reg = <0x40000 0x60000>; + read-only; + }; + + partition@a0000 { + label = "firmware"; + reg = <0xa0000 0xf20000>; + }; + + partition@fc0000 { + label = "sysconfig"; + reg = <0xfc0000 0x40000>; + }; + + partition@0x1000000 { + label = "rootfs_data"; + reg = <0x1000000 0x1000000>; + }; + }; + }; +}; + +&pci0 { + status = "okay"; +}; + +&usb_phy { + status = "okay"; +}; + +&usb { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; + +&vmmc { + status = "okay"; + gpios = <&gpio 31 GPIO_ACTIVE_HIGH>; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/ALL0333CJ.dts b/target/linux/lantiq/files/arch/mips/boot/dts/ALL0333CJ.dts new file mode 100644 index 0000000000..df62ac2d92 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/ALL0333CJ.dts @@ -0,0 +1,116 @@ +/dts-v1/; + +#include "amazonse.dtsi" + +/ { + compatible = "allnet,all0333cj", "lantiq,xway", "lantiq,ase"; + model = "Allnet ALL0333CJ DSL Modem"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + + aliases { + led-boot = &power; + led-failsafe = &power; + led-running = &power; + led-upgrade = &power; + + led-dsl = &dsl; + led-internet = &online_green; + }; + }; + + memory@0 { + reg = <0x0 0x1000000>; + }; + + gpio-leds { + compatible = "gpio-leds"; + + /* power led: red=off, green=on */ + power: power { + label = "all0333cj:green:power"; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + + lan: lan { + label = "all0333cj:green:lan"; + gpios = <&gpio 3 GPIO_ACTIVE_LOW>; + }; + + dsl: dsl { + label = "all0333cj:green:dsl"; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + }; + + online_green: online { + label = "all0333cj:green:online"; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + }; + online_red { + label = "all0333cj:red:online"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + asc { + lantiq,groups = "asc"; + lantiq,function = "asc"; + }; + keys_in { + lantiq,pins = "io0",/* "io25", */"io29"; + lantiq,pull = <2>; + lantiq,open-drain = <1>; + }; + }; +}; + +&gsw { + phy-mode = "mii"; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x400000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x00000 0x10000>; + read-only; + }; + + partition@10000 { + label = "firmware"; + reg = <0x10000 0x3ef200>; + }; + + partition@3ff200 { + label = "uboot_env"; + reg = <0x3ff200 0xc00>; + read-only; + }; + + partition@3ffe00 { + label = "dummy_bits"; + reg = <0x3ffe00 0x200>; + read-only; + }; + }; + }; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/ARV4510PW.dts b/target/linux/lantiq/files/arch/mips/boot/dts/ARV4510PW.dts new file mode 100644 index 0000000000..6598a60f58 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/ARV4510PW.dts @@ -0,0 +1,230 @@ +/dts-v1/; + +#include "danube.dtsi" + +#include + +/ { + compatible = "arcadyan,arv4510pw", "lantiq,xway", "lantiq,danube"; + model = "Wippies, Elisa"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power; + led-failsafe = &power2; + led-running = &power; + led-upgrade = &power; + + led-dsl = &adsl; + led-internet = &internet; + led-usb = &led_usb; + led-usb2 = &led_usb2; + led-wifi = &wifi; + }; + + memory@0 { + reg = <0x0 0x2000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + wps { + label = "wps"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + reset { + label = "reset"; + gpios = <&gpio 3 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + power: power { + label = "power"; + gpios = <&gpios 21 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + power2: power2 { + label = "power2"; + gpios = <&gpios 20 GPIO_ACTIVE_HIGH>; + }; + lan1 { + label = "lan1"; + gpios = <&gpios 19 GPIO_ACTIVE_HIGH>; + }; + lan2 { + label = "lan2"; + gpios = <&gpios 18 GPIO_ACTIVE_HIGH>; + }; + lan3 { + label = "lan3"; + gpios = <&gpios 17 GPIO_ACTIVE_HIGH>; + }; + lan4 { + label = "lan4"; + gpios = <&gpios 16 GPIO_ACTIVE_HIGH>; + }; + wifi: wifi { + label = "wifi"; + gpios = <&gpios 15 GPIO_ACTIVE_HIGH>; + }; + adsl: adsl { + label = "adsl"; + gpios = <&gpios 14 GPIO_ACTIVE_HIGH>; + }; + internet: internet { + label = "internet"; + gpios = <&gpios 13 GPIO_ACTIVE_HIGH>; + }; + internet2 { + label = "internet2"; + gpios = <&gpios 12 GPIO_ACTIVE_HIGH>; + }; + voip { + label = "voip"; + gpios = <&gpios 11 GPIO_ACTIVE_HIGH>; + }; + phone { + label = "phone"; + gpios = <&gpios 10 GPIO_ACTIVE_HIGH>; + }; + phone2 { + label = "phone2"; + gpios = <&gpios 9 GPIO_ACTIVE_HIGH>; + }; + led_usb: usb { + label = "usb"; + gpios = <&gpios 8 GPIO_ACTIVE_HIGH>; + }; + led_usb2: usb2 { + label = "usb2"; + gpios = <&gpios 7 GPIO_ACTIVE_HIGH>; + }; + usb3 { + label = "usb3"; + gpios = <&gpios 6 GPIO_ACTIVE_HIGH>; + }; + unlabeled { + label = "unlabeled"; + gpios = <&gpios 5 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + ebu { + lantiq,groups = "ebu a23"; + lantiq,function = "ebu"; + lantiq,open-drain = <0>; + lantiq,output = <1>; + }; + stp { + lantiq,groups = "stp"; + lantiq,function = "stp"; + lantiq,open-drain = <0>; + lantiq,output = <1>; + }; + exin { + lantiq,groups = "exin1", "exin2"; + lantiq,function = "exin"; + lantiq,output = <0>; + }; + pci_in { + lantiq,groups = "req1", "req2"; + lantiq,function = "pci"; + lantiq,output = <0>; + }; + pci_out { + lantiq,groups = "gnt1", "gnt2"; + lantiq,function = "pci"; + lantiq,open-drain = <0>; + lantiq,pull = <0>; + lantiq,output = <1>; + }; + pci_rst { + lantiq,pins = "io21"; + lantiq,open-drain = <0>; + lantiq,output = <1>; + }; + buttons { + lantiq,pins = "io3", "io14"; + lantiq,pull = <2>; + lantiq,output = <0>; + }; + }; +}; + +&gpios { + status = "okay"; + lantiq,groups = <0x7>; +}; + +&gsw { + phy-mode = "rmii"; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x1000000>; + #address-cells = <1>; + #size-cells = <1>; + + lantiq,noxip; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x00000 0x40000>; + read-only; + }; + + partition@40000 { + label = "uboot_env"; + reg = <0x40000 0x20000>; + read-only; + }; + + partition@60000 { + label = "firmware"; + reg = <0x60000 0xfa0000>; + }; + }; + }; +}; + +&pci0 { + status = "okay"; + lantiq,external-clock; + interrupt-map = < + 0x6000 0 0 1 &icu0 135 + 0x7800 0 0 1 &icu0 66 + 0x7800 0 0 2 &icu0 66 + 0x7800 0 0 3 &icu0 66 + >; + gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; + req-mask = <0x7>; +}; + +&vmmc { + status = "okay"; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/ARV4518PWR01.dts b/target/linux/lantiq/files/arch/mips/boot/dts/ARV4518PWR01.dts new file mode 100644 index 0000000000..34f868f484 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/ARV4518PWR01.dts @@ -0,0 +1,8 @@ +/dts-v1/; + +#include "ARV4518PWR01.dtsi" + +/ { + compatible = "arcadyan,arv4518pwr01", "lantiq,xway", "lantiq,danube"; + model = "SMC7908A-ISP"; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/ARV4518PWR01.dtsi b/target/linux/lantiq/files/arch/mips/boot/dts/ARV4518PWR01.dtsi new file mode 100644 index 0000000000..f29c416c06 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/ARV4518PWR01.dtsi @@ -0,0 +1,206 @@ +#include "danube.dtsi" + +#include + +/ { + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power; + led-failsafe = &power; + led-running = &power; + led-upgrade = &power; + + led-dsl = &dsl; + led-internet = &online; + led-usb = &led_usb; + led-wifi = &wifi; + }; + + memory@0 { + reg = <0x0 0x4000000>; + }; + + ath5k_eep { + compatible = "ath5k,eeprom"; + ath,eep-flash = <&boardconfig 0x400>; + ath,mac-offset = <0x16>; + ath,mac-increment = <1>; + ath,eep-swap; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + rfkill { + label = "rfkill"; + gpios = <&gpio 28 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + reset { + label = "reset"; + gpios = <&gpio 30 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + power: power { + label = "power"; + gpios = <&gpio 3 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + dsl: dsl { + label = "dsl"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + online: online { + label = "online"; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + }; + wifi: wifi { + label = "wifi"; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + }; + wps { + label = "wps"; + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + }; + dsl2 { + label = "dsl2"; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + }; + led_usb: usb { + label = "usb"; + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; + }; + voice { + label = "voice"; + gpios = <&gpiomm 0 GPIO_ACTIVE_LOW>; + }; + fxs1 { + label = "fxs1"; + gpios = <&gpiomm 1 GPIO_ACTIVE_LOW>; + }; + fxs2 { + label = "fxs2"; + gpios = <&gpiomm 2 GPIO_ACTIVE_LOW>; + }; + fxo { + label = "fxo"; + gpios = <&gpiomm 3 GPIO_ACTIVE_LOW>; + }; + }; + + usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio 14 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + ebu { + lantiq,groups = "ebu cs1"; + lantiq,function = "ebu"; + }; + pci_in { + lantiq,groups = "req1", "req2"; + lantiq,function = "pci"; + lantiq,open-drain = <1>; + lantiq,pull = <2>; + lantiq,output = <0>; + }; + pci_out { + lantiq,groups = "gnt1", "gnt2"; + lantiq,function = "pci"; + lantiq,pull = <0>; + lantiq,output = <1>; + }; + }; +}; + +&gpiomm { + status = "okay"; + lantiq,shadow = <0x0>; +}; + +&gsw { + phy-mode = "mii"; + mtd-mac-address = <&boardconfig 0x16>; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x2000000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x00000 0x10000>; /* 64 KB */ + read-only; + }; + + partition@10000 { + label = "uboot_env"; + reg = <0x10000 0x10000>; /* 64 KB */ + read-only; + }; + + partition@20000 { + label = "firmware"; + reg = <0x20000 0x3d0000>; + }; + + boardconfig: partition@400000 { + label = "boardconfig"; + reg = <0x3f0000 0x10000>; + read-only; + }; + }; + }; +}; + +&pci0 { + status = "okay"; + gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; + req-mask = <0xf>; +}; + +&usb_phy { + status = "okay"; +}; + +&usb { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; + +&vmmc { + status = "okay"; + gpios = <&gpio 31 GPIO_ACTIVE_HIGH>; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/ARV4518PWR01A.dts b/target/linux/lantiq/files/arch/mips/boot/dts/ARV4518PWR01A.dts new file mode 100644 index 0000000000..9617398bbc --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/ARV4518PWR01A.dts @@ -0,0 +1,12 @@ +/dts-v1/; + +#include "ARV4518PWR01.dtsi" + +/ { + compatible = "arcadyan,arv4518pwr01a", "lantiq,xway", "lantiq,danube"; + model = "SMC7908A-ISP, Airties WAV-221"; +}; + +&pci0 { + lantiq,external-clock; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/ARV4519PW.dts b/target/linux/lantiq/files/arch/mips/boot/dts/ARV4519PW.dts new file mode 100644 index 0000000000..e307b381a9 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/ARV4519PW.dts @@ -0,0 +1,203 @@ +/dts-v1/; + +#include "danube.dtsi" + +#include + +/ { + compatible = "arcadyan,arv4519pw", "lantiq,xway", "lantiq,danube"; + model = "Vodafone Netfaster IAD 2, Pirelli P.RG A4201G"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power_green; + led-failsafe = &power_red; + led-running = &power_green; + led-upgrade = &power_green; + + led-dsl = &dsl; + led-internet = &internet_green; + led-usb = &led_usb; + led-wifi = &wifi; + }; + + memory@0 { + reg = <0x0 0x2000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + rfkill { + label = "rfkill"; + gpios = <&gpio 28 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + reset { + label = "reset"; + gpios = <&gpio 30 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + power_green: power { + label = "arv4519pw:green:power"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + power_red: power2 { + label = "arv4519pw:red:power"; + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + }; + wifi: wifi { + label = "arv4519pw:green:wlan"; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + }; + dsl: dsl { + label = "arv4519pw:green:dsl"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + internet_green: online { + label = "arv4519pw:green:internet"; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + }; + online2 { + label = "arv4519pw:red:internet"; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + }; + led_usb: usb { + label = "arv4519pw:green:usb"; + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; + }; + voip { + label = "arv4519pw:green:voip"; + gpios = <&gpiomm 0 GPIO_ACTIVE_LOW>; + }; + fxs1 { + label = "arv4519pw:green:phone1"; + gpios = <&gpiomm 1 GPIO_ACTIVE_LOW>; + }; + fxs2 { + label = "arv4519pw:green:phone2"; + gpios = <&gpiomm 2 GPIO_ACTIVE_LOW>; + }; + fxo { + label = "arv4519pw:green:line"; + gpios = <&gpiomm 3 GPIO_ACTIVE_LOW>; + }; + wps2 { + label = "arv4519pw:green:wps"; + gpios = <&gpiomm 4 GPIO_ACTIVE_LOW>; + }; + wps { + label = "arv4519pw:orange:wps"; + gpios = <&gpiomm 5 GPIO_ACTIVE_LOW>; + }; + wps3 { + label = "arv4519pw:red:wps"; + gpios = <&gpiomm 6 GPIO_ACTIVE_LOW>; + }; + }; + + usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio 14 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + ebu { + lantiq,groups = "ebu cs1"; + lantiq,function = "ebu"; + }; + }; +}; + +&gpiomm { + status = "okay"; + lantiq,shadow = <0x400>; +}; + +&gsw { + phy-mode = "mii"; + mtd-mac-address = <&boardconfig 0x16>; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x2000000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x00000 0x10000>; + read-only; + }; + + partition@10000 { + label = "uboot_env"; + reg = <0x10000 0x10000>; + }; + + partition@20000 { + label = "firmware"; + reg = <0x20000 0x3d0000>; + }; + + boardconfig: partition@3f0000 { + label = "boardconfig"; + reg = <0x3f0000 0x10000>; + read-only; + }; + }; + }; +}; + +&pci0 { + status = "okay"; + lantiq,external-clock; + gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; + req-mask = <0xf>; +}; + +&usb_phy { + status = "okay"; +}; + +&usb { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; + +&vmmc { + status = "okay"; + gpios = <&gpio 31 GPIO_ACTIVE_HIGH>; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/ARV4520PW.dts b/target/linux/lantiq/files/arch/mips/boot/dts/ARV4520PW.dts new file mode 100644 index 0000000000..cd76bf5799 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/ARV4520PW.dts @@ -0,0 +1,228 @@ +/dts-v1/; + +#include "danube.dtsi" + +#include + +/ { + compatible = "arcadyan,arv4520pw", "lantiq,xway", "lantiq,danube"; + model = "Easybox 800, WAV-281"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power_blue; + led-failsafe = &power_red; + led-running = &power_blue; + led-upgrade = &power_blue; + + led-dsl = &dsl; + led-internet = &internet_blue; + led-usb = &led_usb; + led-wifi = &wifi; + }; + + memory@0 { + reg = <0x0 0x2000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + rfkill { + label = "wps"; + gpios = <&gpio 29 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + reset { + label = "reset"; + gpios = <&gpio 30 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + power_blue: power { + label = "arv4520pw:blue:power"; + gpios = <&gpio 3 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + dsl: dsl { + label = "arv4520pw:blue:dsl"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + internet_blue: internet { + label = "arv4520pw:blue:internet"; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + }; + power_red: power2 { + label = "arv4520pw:red:power"; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + }; + wps { + label = "arv4520pw:yellow:wps"; + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + }; + wps2 { + label = "arv4520pw:red:wps"; + gpios = <&gpio 9 GPIO_ACTIVE_LOW>; + }; + /* + wps green is missing + */ + fxs1 { + label = "arv4520pw:blue:telefon1"; + gpios = <&gpiomm 0 GPIO_ACTIVE_LOW>; + }; + fxs2 { + label = "arv4520pw:blue:telefon2"; + gpios = <&gpiomm 1 GPIO_ACTIVE_LOW>; + }; + isdn { + label = "arv4520pw:blue:isdn"; + gpios = <&gpiomm 2 GPIO_ACTIVE_LOW>; + }; + fxo { + label = "arv4520pw:blue:line"; + gpios = <&gpiomm 3 GPIO_ACTIVE_LOW>; + }; + voice { + label = "arv4520pw:blue:sprache"; + gpios = <&gpiomm 4 GPIO_ACTIVE_LOW>; + }; + led_usb: usb { + label = "arv4520pw:blue:usb"; + gpios = <&gpiomm 5 GPIO_ACTIVE_LOW>; + }; + wifi: wifi { + label = "arv4520pw:blue:wifi"; + gpios = <&gpiomm 6 GPIO_ACTIVE_LOW>; + }; + internet2 { + label = "arv4520pw:red:internet"; + gpios = <&gpiomm 9 GPIO_ACTIVE_LOW>; + }; + /* + info is missing + */ + }; + + usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio 28 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + ebu { + lantiq,groups = "ebu cs1"; + lantiq,function = "ebu"; + }; + pci_in { + lantiq,groups = "req1"; + lantiq,function = "pci"; + lantiq,open-drain = <1>; + lantiq,pull = <2>; + lantiq,output = <0>; + }; + pci_out { + lantiq,groups = "gnt1"; + lantiq,function = "pci"; + lantiq,output = <1>; + }; + pci_rst { + lantiq,pins = "io21"; + lantiq,open-drain = <0>; + lantiq,pull = <0>; + }; + }; +}; + +&gpiomm { + status = "okay"; + lantiq,shadow = <0x400>; +}; + +&gsw { + /* gpiomm 10 - switch */ + phy-mode = "rmii"; + mtd-mac-address = <&boardconfig 0x16>; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x800000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x00000 0x20000>; + read-only; + }; + + partition@20000 { + label = "uboot_env"; + reg = <0x20000 0x10000>; + read-only; + }; + + partition@30000 { + label = "firmware"; + reg = <0x30000 0x3c0000>; + }; + + boardconfig: partition@7f0000 { + label = "boardconfig"; + reg = <0x3f0000 0x10000>; + read-only; + }; + }; + }; +}; + +&pci0 { + status = "okay"; + lantiq,external-clock; + gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; +}; + +&usb_phy { + status = "okay"; +}; + +&usb { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; + +&vmmc { + status = "okay"; + gpios = <&gpio 31 GPIO_ACTIVE_HIGH + &gpiomm 7 GPIO_ACTIVE_HIGH>; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/ARV4525PW.dts b/target/linux/lantiq/files/arch/mips/boot/dts/ARV4525PW.dts new file mode 100644 index 0000000000..b3904d37d5 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/ARV4525PW.dts @@ -0,0 +1,162 @@ +/dts-v1/; + +#include "danube.dtsi" + +#include + +/ { + compatible = "arcadyan,arv4525pw", "lantiq,xway", "lantiq,danube"; + model = "Speedport W501V Typ A"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + /* we dont have a power led, lets use the online led */ + led-boot = &online; + led-failsafe = &online; + + led-dsl = &dsl; + led-internet = &online; + led-wifi = &wifi; + }; + + memory@0 { + reg = <0x0 0x2000000>; + }; + + ath5k_eep { + compatible = "ath5k,eeprom"; + ath,eep-flash = <&boardconfig 0x400>; + ath,mac-offset = <0x0>; + ath,eep-swap; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + wps { + label = "wps"; + gpios = <&gpio 29 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + reset { + label = "reset"; + gpios = <&gpio 30 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + fxo { + label = "arv4525pw:green:festnetz"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + fxs { + label = "arv4525pw:green:internet"; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + }; + dsl: dsl { + label = "arv4525pw:green:t-dsl"; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + }; + wifi: wifi { + label = "arv4525pw:green:wlan"; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + }; + online: online { + label = "arv4525pw:green:online"; + gpios = <&gpio 9 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + pci_in { + lantiq,groups = "req1"; + lantiq,function = "pci"; + lantiq,open-drain = <1>; + lantiq,pull = <2>; + lantiq,output = <0>; + }; + pci_out { + lantiq,groups = "gnt1"; + lantiq,function = "pci"; + lantiq,output = <1>; + }; + pci_rst { + lantiq,pins = "io21"; + lantiq,pull = <2>; + lantiq,output = <1>; + }; + relay { + lantiq,pins = "io31"; + lantiq,output = <1>; + }; + }; +}; + +/* #define ARV4525PW_PHYRESET 13 */ +&gsw { + phy-mode = "mii"; + mtd-mac-address = <&boardconfig 0x16>; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x2000000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x00000 0x10000>; + read-only; + }; + + partition@10000 { + label = "uboot_env"; + reg = <0x10000 0x10000>; + read-only; + }; + + partition@20000 { + label = "firmware"; + reg = <0x20000 0x3d0000>; + }; + + boardconfig: partition@400000 { + label = "boardconfig"; + reg = <0x3f0000 0x10000>; + read-only; + }; + }; + }; +}; + +&pci0 { + status = "okay"; + gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; +}; + +/* #define ARV4525PW_RELAY 31 */ +&vmmc { + status = "okay"; + gpios = <&gpio 31 GPIO_ACTIVE_HIGH>; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/ARV452CQW.dts b/target/linux/lantiq/files/arch/mips/boot/dts/ARV452CQW.dts new file mode 100644 index 0000000000..203a30df5c --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/ARV452CQW.dts @@ -0,0 +1,246 @@ +/dts-v1/; + +#include "danube.dtsi" + +#include + +/ { + compatible = "arcadyan,arv452cqw", "lantiq,xway", "lantiq,danube"; + model = "Arcor 801"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power_blue; + led-failsafe = &power_red; + led-running = &power_blue; + led-upgrade = &power_blue; + + led-dsl = &dsl_blue; + led-usb = &led_usb; + led-wifi = &wifi; + }; + + memory@0 { + reg = <0x0 0x2000000>; + }; + + ath5k_eep { + compatible = "ath5k,eeprom"; + ath,eep-flash = <&boardconfig 0x400>; + ath,mac-offset = <0x0>; + ath,eep-swap; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + rfkill { + label = "rfkill"; + gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + wps { + label = "wps"; + gpios = <&gpio 29 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + reset { + label = "reset"; + gpios = <&gpio 30 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + power_blue: power0 { + label = "arv452cqw:blue:power"; + gpios = <&gpio 3 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + dsl_blue: dsl { + label = "arv452cqw:blue:dsl"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + isdn { + label = "arv452cqw:blue:isdn"; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + }; + power_red: power1 { + label = "arv452cqw:red:power"; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + }; + wps { + label = "arv452cqw:blue:wps"; + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + }; + wps1 { + label = "arv452cqw:yellow:wps"; + gpios = <&gpio 9 GPIO_ACTIVE_LOW>; + }; + fxs1 { + label = "arv452cqw:blue:telefon1"; + gpios = <&gpiomm 0 GPIO_ACTIVE_LOW>; + }; + fxs2 { + label = "arv452cqw:blue:telefon2"; + gpios = <&gpiomm 1 GPIO_ACTIVE_LOW>; + }; + wps2 { + label = "arv452cqw:red:wps"; + gpios = <&gpiomm 2 GPIO_ACTIVE_LOW>; + }; + fxo { + label = "arv452cqw:blue:line"; + gpios = <&gpiomm 3 GPIO_ACTIVE_LOW>; + }; + voice { + label = "arv452cqw:blue:sprache"; + gpios = <&gpiomm 4 1>; + }; + led_usb: usb { + label = "arv452cqw:blue:usb"; + gpios = <&gpiomm 5 GPIO_ACTIVE_LOW>; + }; + wifi: wifi { + label = "arv452cqw:blue:wlan"; + gpios = <&gpiomm 6 GPIO_ACTIVE_LOW>; + }; + /* + internet blue and internet red are missing + dsl2 and dsl3 are not referenced in manual + */ + dsl2 { + label = "arv452cqw:yellow:dsl"; + gpios = <&gpiomm 8 GPIO_ACTIVE_LOW>; + }; + dsl3 { + label = "arv452cqw:red:dsl"; + gpios = <&gpiomm 9 GPIO_ACTIVE_LOW>; + }; + }; + + usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio 28 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + ebu { + lantiq,groups = "ebu cs1"; + lantiq,function = "ebu"; + }; + pci_in { + lantiq,groups = "req1"; + lantiq,function = "pci"; + lantiq,open-drain = <1>; + lantiq,pull = <2>; + lantiq,output = <0>; + }; + pci_out { + lantiq,groups = "gnt1"; + lantiq,function = "pci"; + lantiq,output = <1>; + }; + pci_rst { + lantiq,pins = "io21"; + lantiq,pull = <0>; + lantiq,output = <1>; + }; + leds { + lantiq,pins = "io3", "io5", "io6", "io7", "io9"; + lantiq,output = <1>; + }; + }; +}; + +&gpiomm { + status = "okay"; + lantiq,shadow = <0x77f>; +}; + +/* +#define ARV452CPW_SWITCH_RESET 110 +*/ +&gsw { + phy-mode = "rmii"; + mtd-mac-address = <&boardconfig 0x16>; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x400000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x00000 0x10000>; + read-only; + }; + + partition@10000 { + label = "uboot_env"; + reg = <0x10000 0x10000>; + read-only; + }; + + partition@20000 { + label = "firmware"; + reg = <0x20000 0x3d0000>; + }; + + boardconfig: partition@3f0000 { + label = "boardconfig"; + reg = <0x3f0000 0x10000>; + read-only; + }; + }; + }; +}; + +&pci0 { + status = "okay"; + lantiq,external-clock; + gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; +}; + +&usb_phy { + status = "okay"; +}; + +&usb { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; + +&vmmc { + status = "okay"; + gpios = <&gpio 31 GPIO_ACTIVE_HIGH + &gpiomm 7 GPIO_ACTIVE_HIGH>; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/ARV7506PW11.dts b/target/linux/lantiq/files/arch/mips/boot/dts/ARV7506PW11.dts new file mode 100644 index 0000000000..8fe22e9a44 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/ARV7506PW11.dts @@ -0,0 +1,164 @@ +/dts-v1/; + +#include "danube.dtsi" + +#include + +/ { + compatible = "arcadyan,arv7506pw11", "lantiq,xway", "lantiq,danube"; + model = "Alice/O2 IAD 4421"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power; + led-failsafe = &power_red; + led-running = &power; + led-upgrade = &power; + + led-dsl = &dsl; + led-internet = &internet; + led-wifi = &wlan; + }; + + memory@0 { + reg = <0x0 0x4000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + rfkill { + label = "rfkill"; + gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + reset { + label = "reset"; + gpios = <&gpio 30 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + wlan: wlan { + label = "arv7506pw11:green:wlan"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + }; + power: power { + label = "arv7506pw11:green:power"; + gpios = <&gpio 3 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + dsl: dsl { + label = "arv7506pw11:green:dsl"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + internet: internet { + label = "arv7506pw11:green:internet"; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + }; + power_red: power_red { + label = "arv7506pw11:red:power"; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + }; + internet_red { + label = "arv7506pw11:red:internet"; + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + }; + info { + label = "arv7506pw11:green:info"; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + }; + telefon { + label = "arv7506pw11:green:telefon"; + gpios = <&gpio 9 GPIO_ACTIVE_LOW>; + }; + info_red { + label = "arv7506pw11:red:info"; + gpios = <&gpio 20 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + pci { + lantiq,groups = "gnt1"; + lantiq,function = "pci"; + lantiq,output = <1>; + }; + pci_rst { + lantiq,pins = "io21"; + lantiq,pull = <2>; + lantiq,output = <1>; + }; + }; +}; + +/* GPIO 19: switch reset */ +&gsw { + phy-mode = "rmii"; + mtd-mac-address = <&boardconfig 0x16>; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x800000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x00000 0x40000>; + read-only; + }; + + partition@40000 { + label = "uboot_env"; + reg = <0x40000 0x10000>; + read-only; + }; + + partition@50000 { + label = "firmware"; + reg = <0x50000 0x7a0000>; + }; + + boardconfig: partition@7f0000 { + label = "board_config"; + reg = <0x7f0000 0x10000>; + read-only; + }; + }; + }; +}; + +&pci0 { + status = "okay"; + lantiq,external-clock; + gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; + + wifi@1814,3592 { + compatible = "pci1814,3592"; + reg = <0x7000 0 0 0 0>; + ralink,mtd-eeprom = <&boardconfig 0x410>; + ralink,mtd-eeprom-swap; + mtd-mac-address = <&boardconfig 0x16>; + mtd-mac-address-increment = <1>; + }; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/ARV7510PW22.dts b/target/linux/lantiq/files/arch/mips/boot/dts/ARV7510PW22.dts new file mode 100644 index 0000000000..92d01b4dcc --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/ARV7510PW22.dts @@ -0,0 +1,209 @@ +/dts-v1/; + +#include "danube.dtsi" + +#include + +/ { + compatible = "arcadyan,arv7510pw22", "lantiq,xway", "lantiq,danube"; + model = "Astoria Networks ARV7510PW22"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power; + led-failsafe = &power; + led-running = &power; + led-upgrade = &power; + + led-dsl = &internet; + led-usb = &umts; + led-wifi = &wlan; + }; + + memory@0 { + reg = <0x0 0x4000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + rfkill { + label = "rfkill"; + gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + restart { + label = "restart"; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + reset { + label = "reset"; + gpios = <&gpio 28 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + power: power { + label = "power"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + internet: internet { + label = "internet"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + wlan: wlan { + label = "wlan"; + gpios = <&gpio 10 GPIO_ACTIVE_LOW>; + }; + umts: 3g { + label = "3g"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + }; + message { + label = "message"; + gpios = <&gpio 20 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + exin { + lantiq,groups = "exin1"; + lantiq,function = "exin"; + lantiq,pull = <2>; + lantiq,output = <0>; + }; + pci_in { + lantiq,groups = "req1", "req2"; + lantiq,function = "pci"; + lantiq,open-drain = <1>; + lantiq,pull = <2>; + lantiq,output = <0>; + }; + pci_out { + lantiq,groups = "gnt1"; + lantiq,function = "pci"; + lantiq,output = <1>; + }; + pci_rst { + lantiq,pins = "io21"; + lantiq,pull = <2>; + lantiq,output = <1>; + }; + pins_out { + lantiq,pins = "io2", "io4", "io8", "io9", "io10", "io15", "io20"; + lantiq,output = <1>; + }; + pins_in { + lantiq,pins = "io11", "io12", "io28"; + lantiq,open-drain = <1>; + lantiq,pull = <2>; + lantiq,output = <0>; + }; + }; + + usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio 8 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&gsw { + /* Switch reset 19 */ + phy-mode = "mii"; + mtd-mac-address = <&boardconfig 0x16>; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x1000000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x00000 0x40000>; + read-only; + }; + + partition@40000 { + label = "uboot_env"; + reg = <0x40000 0x20000>; + read-only; + }; + + partition@60000 { + label = "firmware"; + reg = <0x60000 0xf80000>; + }; + + boardconfig: partition@fe0000 { + label = "board_config"; + reg = <0xfe0000 0x20000>; + read-only; + }; + }; + }; +}; + +&pci0 { + status = "okay"; + lantiq,external-clock; + interrupt-map = < + 0x7000 0 0 1 &icu0 30 + 0x7800 0 0 1 &icu0 135 + 0x7800 0 0 2 &icu0 135 + 0x7800 0 0 3 &icu0 135 + >; + gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; + req-mask = <0x3>; + + wifi@1814,3592 { + compatible = "pci1814,3592"; + reg = <0x7000 0 0 0 0>; + ralink,mtd-eeprom = <&boardconfig 0x410>; + ralink,mtd-eeprom-swap; + }; +}; + +&usb_phy { + status = "okay"; +}; + +&usb { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; + +&vmmc { + status = "okay"; + gpios = <&gpio 9 GPIO_ACTIVE_HIGH>; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/ARV7518PW.dts b/target/linux/lantiq/files/arch/mips/boot/dts/ARV7518PW.dts new file mode 100644 index 0000000000..72f3a686b5 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/ARV7518PW.dts @@ -0,0 +1,240 @@ +/dts-v1/; + +#include "danube.dtsi" + +#include + +/ { + compatible = "arcadyan,arv7518pw", "lantiq,xway", "lantiq,danube"; + model = "Astoria Networks ARV7518PW"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power_green; + led-failsafe = &power_red; + led-running = &power_green; + led-upgrade = &power_green; + + led-dsl = &dsl; + led-internet = &online_green; + led-usb = &led_usb; + led-wifi = &wifi; + }; + + memory@0 { + reg = <0x0 0x4000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + rfkill { + label = "rfkill"; + gpios = <&gpio 28 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + reset { + label = "reset"; + gpios = <&gpio 30 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + power_green: power { + label = "arv7518pw:green:power"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + dsl: dsl { + label = "arv7518pw:green:dsl"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + online_green: online { + label = "arv7518pw:green:internet"; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + }; + wifi: wifi { + label = "arv7518pw:green:wlan"; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + }; + power_red: power2 { + label = "arv7518pw:red:power"; + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + }; + online2 { + label = "arv7518pw:red:internet"; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + }; + led_usb: usb { + label = "arv7518pw:green:usb"; + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; + }; + voice { + label = "arv7518pw:green:voip"; + gpios = <&gpiomm 0 GPIO_ACTIVE_LOW>; + }; + fxs1 { + label = "arv7518pw:green:phone1"; + gpios = <&gpiomm 1 GPIO_ACTIVE_LOW>; + }; + fxs2 { + label = "arv7518pw:green:phone2"; + gpios = <&gpiomm 2 GPIO_ACTIVE_LOW>; + }; + unlabeled { + label = "arv7518pw:amber:unlabeled"; + gpios = <&gpiomm 3 GPIO_ACTIVE_LOW>; + }; + wps { + label = "arv7518pw:amber:wps"; + gpios = <&gpiomm 4 GPIO_ACTIVE_LOW>; + }; + wps2 { + label = "arv7518pw:green:wps"; + gpios = <&gpiomm 5 GPIO_ACTIVE_LOW>; + }; + wps3 { + label = "arv7518pw:red:wps"; + gpios = <&gpiomm 6 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + ebu { + lantiq,groups = "ebu cs1"; + lantiq,function = "ebu"; + }; + pci_in { + lantiq,groups = "req1"; + lantiq,function = "pci"; + lantiq,open-drain = <1>; + lantiq,pull = <2>; + lantiq,output = <0>; + }; + pci_out { + lantiq,groups = "gnt1"; + lantiq,function = "pci"; + lantiq,pull = <0>; + lantiq,output = <1>; + }; + pci_rst { + lantiq,pins = "io21"; + lantiq,pull = <2>; + lantiq,output = <1>; + }; + leds { + lantiq,pins = "io2", "io4", "io5", "io6", "io7", "io8", "io19"; + lantiq,output = <1>; + }; + keys { + lantiq,pins = "io28", "io30"; + lantiq,output = <0>; + lantiq,pull = <2>; + lantiq,open-drain = <1>; + }; + }; + + usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio 14 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&gpiomm { + status = "okay"; + lantiq,shadow = <0x0>; +}; + +/* +#define SWITCH_RESET 13 +*/ +&gsw { + phy-mode = "mii"; + mtd-mac-address = <&boardconfig 0x16>; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x2000000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x00000 0x10000>; + read-only; + }; + + partition@10000 { + label = "uboot_env"; + reg = <0x10000 0x10000>; + }; + + partition@20000 { + label = "firmware"; + reg = <0x20000 0x7d0000>; + }; + + boardconfig: partition@400000 { + label = "boardconfig"; + reg = <0x7f0000 0x10000>; + read-only; + }; + }; + }; +}; + +&pci0 { + status = "okay"; + gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; + lantiq,external-clock; + req-mask = <0xf>; + + wifi@168c,0029 { + compatible = "pci168c,0029"; + reg = <0x7000 0 0 0 0>; + qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:00:0e.0.bin */ + mtd-mac-address = <&boardconfig 0x16>; + mtd-mac-address-increment = <1>; + }; +}; + +&usb_phy { + status = "okay"; +}; + +&usb { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; + +&vmmc { + status = "okay"; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/ARV7519PW.dts b/target/linux/lantiq/files/arch/mips/boot/dts/ARV7519PW.dts new file mode 100644 index 0000000000..bcb3b502af --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/ARV7519PW.dts @@ -0,0 +1,229 @@ +/dts-v1/; + +#include "danube.dtsi" + +#include + +/ { + compatible = "arcadyan,arv7519pw", "lantiq,xway", "lantiq,danube"; + model = "Astoria Networks ARV7519PW"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power; + led-failsafe = &power2; + led-running = &power; + led-upgrade = &power; + + led-dsl = &dsl; + led-internet = &online; + led-wifi = &wifi; + }; + + memory@0 { + reg = <0x0 0x4000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + rfkill { + label = "rfkill"; + gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + reset { + label = "reset"; + gpios = <&gpio 28 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + power: power { + label = "power"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + power2: power2 { + label = "power2"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + }; + online: online { + label = "online"; + gpios = <&gpio 3 GPIO_ACTIVE_LOW>; + }; + online2 { + label = "online2"; + gpios = <&gpio 30 GPIO_ACTIVE_LOW>; + }; + wifi: wifi { + label = "wifi"; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + }; + wifi2 { + label = "wifi2"; + gpios = <&gpio 10 GPIO_ACTIVE_LOW>; + }; + wifi3 { + label = "wifi3"; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + }; + voice { + label = "voice"; + gpios = <&gpio 31 GPIO_ACTIVE_LOW>; + }; + wps { + label = "wps"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + }; + wps2 { + label = "wps2"; + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + }; + wps3 { + label = "wps3"; + gpios = <&gpio 23 GPIO_ACTIVE_LOW>; + }; + dsl: dsl { + label = "dsl"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + lan { + label = "lan"; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + }; + tv { + label = "tv"; + gpios = <&gpio 20 GPIO_ACTIVE_LOW>; + }; + upgrade { + label = "upgrade"; + gpios = <&gpio 29 GPIO_ACTIVE_LOW>; + }; + }; + + /* is there another way to "reserve" the GPIO? */ + gpio_export { + compatible = "gpio-export"; + #size-cells = <0>; + + switch { + gpio-export,name = "switch"; + gpio-export,output = <1>; + gpios = <&gpio 19 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + ebu { + lantiq,groups = "ebu cs1"; + lantiq,function = "ebu"; + }; + pci_in { + lantiq,groups = "req1"; + lantiq,function = "pci"; + lantiq,open-drain = <1>; + lantiq,pull = <2>; + lantiq,output = <0>; + }; + pci_out { + lantiq,groups = "gnt1"; + lantiq,function = "pci"; + lantiq,pull = <0>; + lantiq,output = <1>; + }; + pci_rst { + lantiq,pins = "io21"; + lantiq,pull = <2>; + lantiq,output = <1>; + }; + switch_rst { + lantiq,pins = "io19"; + lantiq,pull = <2>; + lantiq,output = <1>; + }; + }; +}; + +&gsw { + phy-mode = "mii"; + mtd-mac-address = <&boardconfig 0x16>; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x2000000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x00000 0x40000>; + read-only; + }; + + partition@40000 { + label = "uboot_env"; + reg = <0x40000 0x20000>; + }; + + partition@60000 { + label = "firmware"; + reg = <0x60000 0xf80000>; + }; + + boardconfig: partition@fe0000 { + label = "board_config"; + reg = <0xfe0000 0x20000>; + read-only; + }; + }; + }; +}; + +&pci0 { + status = "okay"; + lantiq,external-clock; + gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; + req-mask = <0xf>; + + wifi@0,0 { + compatible = "pci0,0"; + reg = <0x7000 0 0 0 0>; + ralink,mtd-eeprom = <&boardconfig 0x410>; + ralink,mtd-eeprom-swap; + }; +}; + +&usb_phy { + status = "okay"; +}; + +/* warning: passive port only works with active devices */ +&usb { + status = "okay"; +}; + +&vmmc { + status = "okay"; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/ARV7519RW22.dts b/target/linux/lantiq/files/arch/mips/boot/dts/ARV7519RW22.dts new file mode 100644 index 0000000000..baa9adcc9c --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/ARV7519RW22.dts @@ -0,0 +1,254 @@ +/dts-v1/; + +#include "vr9.dtsi" + +#include +#include + +/ { + compatible = "arcadyan,arv7519rw22", "lantiq,xway", "lantiq,vr9"; + model = "Orange Livebox 2.1"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power_green; + led-failsafe = &power_green; + led-running = &power_green; + led-upgrade = &power_green; + + led-dsl = &internet_green; + }; + + memory@0 { + reg = <0x0 0x8000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + reset { + label = "reset"; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + rfkill { + label = "rfkill"; + gpios = <&gpio 33 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + wps { + label = "wps"; + gpios = <&gpio 37 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + lan_green { + label = "arv7519rw22:green:lan"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + }; + internet_red { + label = "arv7519rw22:red:internet"; + gpios = <&gpio 10 GPIO_ACTIVE_LOW>; + }; + power_green: power_green { + label = "arv7519rw22:green:power"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + alarm_blue { + label = "arv7519rw22:blue:alarm"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + }; + internet_orange { + label = "arv7519rw22:orange:internet"; + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; + }; + internet_green: internet_green { + label = "arv7519rw22:green:internet"; + gpios = <&gpio 28 GPIO_ACTIVE_LOW>; + }; + voice_green { + label = "arv7519rw22:green:voice"; + gpios = <&gpio 29 GPIO_ACTIVE_LOW>; + }; + }; + + usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio 32 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +ð0 { + lan: interface@0 { + compatible = "lantiq,xrx200-pdi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + mtd-mac-address = <&boardconfig 0x16>; + lantiq,switch; + + ethernet@0 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <0>; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + }; + ethernet@1 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <4>; + phy-mode = "mii"; + phy-handle = <&phy13>; + }; + ethernet@2 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <5>; + phy-mode = "mii"; + phy-handle = <&phy14>; + }; + ethernet@3 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <2>; + phy-mode = "mii"; + phy-handle = <&phy11>; + }; + ethernet@4 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <3>; + phy-mode = "mii"; + phy-handle = <&phy12>; + }; + }; + + mdio@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-mdio"; + reg = <0>; + + phy0: ethernet-phy@0 { + reg = <0x0>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + phy11: ethernet-phy@11 { + reg = <0x11>; + compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; + }; + phy12: ethernet-phy@12 { + reg = <0x12>; + compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; + }; + phy13: ethernet-phy@13 { + reg = <0x13>; + compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; + }; + phy14: ethernet-phy@14 { + reg = <0x14>; + compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; + }; + }; +}; + +&gphy0 { + lantiq,gphy-mode = ; +}; + +&gphy1 { + lantiq,gphy-mode = ; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + mdio { + lantiq,groups = "mdio"; + lantiq,function = "mdio"; + }; + pcie-rst { + lantiq,pins = "io21"; + lantiq,pull = <0>; + lantiq,output = <1>; + }; + }; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x2000000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x0 0x60000>; + read-only; + }; + + partition@60000 { + label = "uboot-env"; + reg = <0x60000 0x20000>; + read-only; + }; + + partition@80000 { + label = "firmware"; + reg = <0x80000 0x1f00000>; + }; + + boardconfig: partition@1f80000 { + label = "boardconfig"; + reg = <0x1f80000 0x80000>; + read-only; + }; + }; + }; +}; + +&pcie0 { + status = "okay"; + gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; +}; + +&usb_phy0 { + status = "okay"; +}; + +&usb_phy1 { + status = "okay"; +}; + +&usb0 { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; + +&usb1 { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/ARV7525PW.dts b/target/linux/lantiq/files/arch/mips/boot/dts/ARV7525PW.dts new file mode 100644 index 0000000000..a395d4ff45 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/ARV7525PW.dts @@ -0,0 +1,152 @@ +/dts-v1/; + +#include "danube.dtsi" + +#include + +/ { + compatible = "arcadyan,arv7525pw", "lantiq,xway", "lantiq,danube"; + model = "Speedport W303V Typ A"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power_green; + led-failsafe = &power_red; + led-running = &power_green; + led-upgrade = &power_green; + + led-dsl = &power_green; + led-internet = &online; + led-wifi = &wifi; + }; + + memory@0 { + reg = <0x0 0x2000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + wps { + label = "wps"; + gpios = <&gpio 29 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + reset { + label = "reset"; + gpios = <&gpio 30 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + power_green: power { + label = "arv7525pw:green:power"; + gpios = <&gpio 3 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + power_red: power1 { + label = "arv7525pw:red:power"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + online: online { + label = "arv7525pw:green:online"; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + }; + voice { + label = "arv7525pw:green:telefonie"; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + }; + voice2 { + label = "arv7525pw:red:telefonie"; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + }; + wifi: wifi { + label = "arv7525pw:green:wlan"; + gpios = <&gpio 9 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + exin { + lantiq,groups = "exin1"; + lantiq,function = "exin"; + }; + pci { + lantiq,groups = "gnt1", "req1"; + lantiq,function = "pci"; + }; + }; +}; + +&gsw { + phy-mode = "mii"; + mtd-mac-address = <&boardconfig 0x16>; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x2000000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x00000 0x10000>; + read-only; + }; + + partition@10000 { + label = "uboot_env"; + reg = <0x10000 0x10000>; + read-only; + }; + + partition@20000 { + label = "firmware"; + reg = <0x20000 0x3d0000>; + }; + + boardconfig: partition@400000 { + label = "board_config"; + reg = <0x3f0000 0x10000>; + read-only; + }; + }; + }; +}; + +&pci0 { + status = "okay"; + interrupt-map = <0x7000 0 0 1 &icu0 135 1>; + + wifi@0,0 { + compatible = "pci0,0"; + reg = <0x7000 0 0 0 0>; + ralink,mtd-eeprom = <&boardconfig 0x410>; + }; +}; + +&vmmc { + status = "okay"; + gpios = <&gpio 31 GPIO_ACTIVE_HIGH>; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/ARV752DPW.dts b/target/linux/lantiq/files/arch/mips/boot/dts/ARV752DPW.dts new file mode 100644 index 0000000000..5f877723f6 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/ARV752DPW.dts @@ -0,0 +1,246 @@ +/dts-v1/; + +#include "danube.dtsi" + +#include + +/ { + compatible = "arcadyan,arv752dpw", "lantiq,xway", "lantiq,danube"; + model = "Arcor 802"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power_red; + led-failsafe = &power_blue; + led-running = &power_red; + led-upgrade = &power_red; + + led-dsl = &internet_red; + led-usb = &umts; + led-wifi = &wifi; + }; + + memory@0 { + reg = <0x0 0x4000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + wps { + label = "wps"; + gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + restart { + label = "restart"; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + dsl { + label = "dsl"; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + reset { + label = "reset"; + gpios = <&gpio 30 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + power_blue: power1 { + label = "arv752dpw:blue:power"; + gpios = <&gpio 3 GPIO_ACTIVE_LOW>; + }; + internet_red: internet { + label = "arv752dpw:red:internet"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + message { + label = "arv752dpw:red:message"; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + }; + power_red: power { + label = "arv752dpw:red:power"; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + voice1 { + label = "arv752dpw:red:voice"; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + }; + umts: umts { + label = "arv752dpw:red:umts"; + gpios = <&gpiomm 3 GPIO_ACTIVE_LOW>; + }; + wifi: wifi { + label = "arv752dpw:red:wifi"; + gpios = <&gpiomm 4 GPIO_ACTIVE_LOW>; + }; + fxs1 { + label = "arv752dpw:green:tae-n"; + gpios = <&gpiomm 5 GPIO_ACTIVE_LOW>; + }; + fxs2 { + label = "arv752dpw:green:tae-u"; + gpios = <&gpiomm 6 GPIO_ACTIVE_LOW>; + }; + fxo { + label = "arv752dpw:green:isdn"; + gpios = <&gpiomm 7 GPIO_ACTIVE_LOW>; + }; + internet2 { + label = "arv752dpw:blue:internet"; + gpios = <&gpiomm 8 GPIO_ACTIVE_LOW>; + }; + voice2 { + label = "arv752dpw:blue:voice"; + gpios = <&gpiomm 9 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + ebu { + lantiq,groups = "ebu cs1"; + lantiq,function = "ebu"; + }; + exin { + lantiq,groups = "exin1"; + lantiq,function = "exin"; + lantiq,pull = <2>; + lantiq,output = <0>; + }; + pci_in { + lantiq,groups = "req2", "req1"; + lantiq,function = "pci"; + lantiq,open-drain = <1>; + lantiq,pull = <2>; + lantiq,output = <0>; + }; + pci_out { + lantiq,groups = "gnt1"; + lantiq,function = "pci"; + lantiq,output = <1>; + }; + pci_rst { + lantiq,pins = "io21"; + lantiq,pull = <2>; + lantiq,output = <1>; + }; + leds { + lantiq,pins = "io3", "io5", "io6", "io8"; + lantiq,output = <1>; + lantiq,pull = <0>; + }; + keys { + lantiq,pins = "io11", "io12", "io13", "io28"; + lantiq,output = <0>; + lantiq,pull = <2>; + lantiq,open-drain = <1>; + }; + }; + + usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpiomm 0 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&gpiomm { + status = "okay"; + lantiq,shadow = <0x3>; +}; + +&gsw { + phy-mode = "rmii"; + mtd-mac-address = <&boardconfig 0x16>; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x800000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x00000 0x10000>; + read-only; + }; + + partition@10000 { + label = "uboot_env"; + reg = <0x10000 0x10000>; + read-only; + }; + + partition@20000 { + label = "firmware"; + reg = <0x20000 0x7d0000>; + }; + + boardconfig: partition@7f0000 { + label = "board_config"; + reg = <0x7f0000 0x10000>; + read-only; + }; + }; + }; +}; + +&pci0 { + status = "okay"; + lantiq,external-clock; + gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; + interrupt-map = <0x7000 0 0 1 &icu0 135>; + req-mask = <0x3>; + + wifi@1814,0601 { + compatible = "pci1814,0601"; + reg = <0x7000 0 0 0 0>; + ralink,mtd-eeprom = <&boardconfig 0x410>; + ralink,mtd-eeprom-swap; + }; +}; + +&usb_phy { + status = "okay"; +}; + +&usb { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; + +&vmmc { + status = "okay"; + gpios = <&gpiomm 1 GPIO_ACTIVE_HIGH>; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/ARV752DPW22.dts b/target/linux/lantiq/files/arch/mips/boot/dts/ARV752DPW22.dts new file mode 100644 index 0000000000..1d4d662ab3 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/ARV752DPW22.dts @@ -0,0 +1,268 @@ +/dts-v1/; + +#include "danube.dtsi" + +#include + +/ { + compatible = "arcadyan,arv752dpw22", "lantiq,xway", "lantiq,danube"; + model = "Arcor 803"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power_red; + led-failsafe = &power_blue; + led-running = &power_red; + led-upgrade = &power_red; + + led-dsl = &internet_red; + led-usb = &umts; + led-wifi = &wifi; + }; + + memory@0 { + reg = <0x0 0x4000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + wps { + label = "wps"; + gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + restart { + label = "restart"; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + dsl { + label = "dsl"; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + reset { + label = "reset"; + gpios = <&gpio 28 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + power_blue: power1 { + label = "arv752dpw22:blue:power"; + gpios = <&gpio 3 GPIO_ACTIVE_LOW>; + }; + internet_red: internet { + label = "arv752dpw22:red:internet"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + message { + label = "arv752dpw22:red:message"; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + }; + power_red: power { + label = "arv752dpw22:red:power"; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + voice1 { + label = "arv752dpw22:red:voice"; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + }; + umts: umts { + label = "arv752dpw22:red:umts"; + gpios = <&gpiomm 3 GPIO_ACTIVE_LOW>; + }; + wifi: wifi { + label = "arv752dpw22:red:wifi"; + gpios = <&gpiomm 4 GPIO_ACTIVE_LOW>; + }; + fxs1 { + label = "arv752dpw22:green:tae-n"; + gpios = <&gpiomm 5 GPIO_ACTIVE_LOW>; + }; + fxs2 { + label = "arv752dpw22:green:tae-u"; + gpios = <&gpiomm 6 GPIO_ACTIVE_LOW>; + }; + fxo { + label = "arv752dpw22:green:isdn"; + gpios = <&gpiomm 7 GPIO_ACTIVE_LOW>; + }; + internet2 { + label = "arv752dpw22:blue:internet"; + gpios = <&gpiomm 8 GPIO_ACTIVE_LOW>; + }; + voice2 { + label = "arv752dpw22:blue:voice"; + gpios = <&gpiomm 9 GPIO_ACTIVE_LOW>; + }; + eth1 { + label = "arv752dpw22:green:lan1"; + gpios = <&gpiomm 11 GPIO_ACTIVE_LOW>; + }; + eth2 { + label = "arv752dpw22:green:lan2"; + gpios = <&gpiomm 12 GPIO_ACTIVE_LOW>; + }; + eth3 { + label = "arv752dpw22:green:lan3"; + gpios = <&gpiomm 13 GPIO_ACTIVE_LOW>; + }; + eth4 { + label = "arv752dpw22:green:lan4"; + gpios = <&gpiomm 14 GPIO_ACTIVE_LOW>; + }; + }; + + usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpiomm 0 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + ebu { + lantiq,groups = "ebu cs1"; + lantiq,function = "ebu"; + }; + exin { + lantiq,groups = "exin1"; + lantiq,function = "exin"; + lantiq,pull = <2>; + lantiq,output = <0>; + }; + pci_in { + lantiq,groups = "req1"; + lantiq,function = "pci"; + lantiq,pull = <2>; + lantiq,output = <0>; + }; + pci_out { + lantiq,groups = "gnt1"; + lantiq,function = "pci"; + lantiq,open-drain = <1>; + lantiq,output = <1>; + }; + pci_rst { + lantiq,pins = "io21"; + lantiq,open-drain = <1>; + lantiq,output = <1>; + }; + leds { + lantiq,pins = "io3", "io5", "io6", "io8"; + lantiq,open-drain = <1>; + lantiq,output = <1>; + }; + buttons { + lantiq,pins = "io11", "io12", "io13", "io28"; + lantiq,pull = <2>; + lantiq,output = <0>; + }; + }; +}; + + +&gpiomm { + status = "okay"; + lantiq,shadow = <3>; +}; + +&gsw { + phy-mode = "mii"; + mtd-mac-address = <&boardconfig 0x16>; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x800000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x00000 0x30000>; + read-only; + }; + + partition@10000 { + label = "uboot_env"; + reg = <0x30000 0x10000>; + read-only; + }; + + partition@20000 { + label = "firmware"; + reg = <0x40000 0x7b0000>; + }; + + boardconfig: partition@7f0000 { + label = "board_config"; + reg = <0x7f0000 0x10000>; + read-only; + }; + }; + }; +}; + +&pci0 { + status = "okay"; + lantiq,external-clock; + interrupt-map = < + 0x7000 0 0 1 &icu0 30 + 0x7800 0 0 1 &icu0 135 + 0x7800 0 0 2 &icu0 135 + 0x7800 0 0 3 &icu0 135 + >; + gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; + req-mask = <0x3>; + + wifi@1814,3592 { + compatible = "pci1814,3592"; + reg = <0x7000 0 0 0 0>; + ralink,mtd-eeprom = <&boardconfig 0x410>; + ralink,mtd-eeprom-swap; + mtd-mac-address = <&boardconfig 0x16>; + }; +}; + +&usb_phy { + status = "okay"; +}; + +&usb { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; + +&vmmc { + status = "okay"; + gpios = <&gpiomm 1 GPIO_ACTIVE_HIGH>; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/ARV8539PW22.dts b/target/linux/lantiq/files/arch/mips/boot/dts/ARV8539PW22.dts new file mode 100644 index 0000000000..1e55d81590 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/ARV8539PW22.dts @@ -0,0 +1,192 @@ +/dts-v1/; + +#include "danube.dtsi" + +#include + +/ { + compatible = "arcadyan,arv8539pw22", "lantiq,xway", "lantiq,danube"; + model = "Speedport W 504V Typ A"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power_green; + led-failsafe = &power_red; + led-running = &power_green; + led-upgrade = &power_green; + + led-dsl = &dsl_green; + led-internet = &online_green; + led-wifi = &wireless_green; + }; + + memory@0 { + reg = <0x0 0x4000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + wlan { + label = "wlan"; + gpios = <&gpio 29 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + reset { + label = "reset"; + gpios = <&gpio 30 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + /* key DECT is missing */ + }; + + gpio-leds { + compatible = "gpio-leds"; + + power_green: power-green { + label = "arv8539pw22:green:power"; + gpios = <&gpio 24 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + power_red: power-red { + label = "arv8539pw22:red:power"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + + dsl_green: dsl-green { + label = "arv8539pw22:green:dsl"; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + }; + + online_green: online-green { + label = "arv8539pw22:green:online"; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + }; + + wireless_green: wireless-green { + label = "arv8539pw22:green:wlan"; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + }; + /* + telefonie green is missing + */ + }; + + usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio 14 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + pci_in { + lantiq,groups = "req1"; + lantiq,function = "pci"; + lantiq,open-drain = <1>; + lantiq,pull = <2>; + lantiq,output = <0>; + }; + pci_out { + lantiq,groups = "gnt1"; + lantiq,function = "pci"; + lantiq,output = <1>; + }; + pci_rst { + lantiq,pins = "io21"; + lantiq,pull = <2>; + lantiq,output = <1>; + }; + relay { + lantiq,pins = "io31"; + lantiq,output = <1>; + }; + }; +}; + +&gsw { + phy-mode = "mii"; + mtd-mac-address = <&art 0x16>; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x800000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x00000 0x30000>; /* 192 KiB */ + read-only; + }; + + partition@30000 { + label = "uboot"; + reg = <0x30000 0x10000>; /* 64 KiB */ + read-only; + }; + + partition@40000 { + label = "firmware"; + reg = <0x40000 0x7B0000>; /* 7872 KiB */ + }; + + art: partition@7F0000 { + label = "art"; + reg = <0x7F0000 0x10000>; /* 64 KiB*/ + read-only; + }; + }; + }; +}; + +&pci0 { + status = "okay"; + gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; + + wifi@168c,0029 { + compatible = "pci168c,0029"; + reg = <0x7000 0 0 0 0>; + qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:00:0e.0.bin */ + mtd-mac-address = <&art 0x16>; + mtd-mac-address-increment = <1>; + }; +}; + +&usb_phy { + status = "okay"; +}; + +&usb { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; + +&vmmc { + status = "okay"; + gpios = <&gpio 31 GPIO_ACTIVE_HIGH>; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/ASL56026.dts b/target/linux/lantiq/files/arch/mips/boot/dts/ASL56026.dts new file mode 100644 index 0000000000..90bfcabcb5 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/ASL56026.dts @@ -0,0 +1,171 @@ +/dts-v1/; + +#include "vr9.dtsi" + +#include +#include + +/ { + compatible = "alphanetworks,asl56026", "lantiq,xway", "lantiq,vr9"; + model = "BT OpenReach VDSL Modem"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power_green; + led-failsafe = &power_red; + led-running = &power_green; + led-upgrade = &power_green; + + led-dsl = &dsl; + }; + + memory@0 { + reg = <0x0 0x2000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + reset { + label = "reset"; + gpios = <&gpio 40 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + dsl: dsl { + label = "asl56026:green:dsl"; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + }; + + /* power-* is a bicolour led */ + power_green: power_green { + label = "asl56026:green:power"; + gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + + power_red: power_red { + label = "asl56026:red:power"; + gpios = <&gpio 18 GPIO_ACTIVE_HIGH>; + }; + }; + + gpio_export { + compatible = "gpio-export"; + #size-cells = <0>; + + power_led_blink { + gpio-export,name = "power_led_blink"; + gpio-export,output = <0>; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + }; + }; +}; + +ð0 { + lan: interface@0 { + compatible = "lantiq,xrx200-pdi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + lantiq,switch; + + ethernet@2 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <2>; + phy-mode = "mii"; + phy-handle = <&phy11>; + }; + + ethernet@3 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <3>; + phy-mode = "mii"; + phy-handle = <&phy14>; + }; + }; + + mdio@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-mdio"; + reg = <0>; + + phy11: ethernet-phy@11 { + reg = <0x11>; + compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; + }; + + phy14: ethernet-phy@14 { + reg = <0x14>; + compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; + }; + }; +}; + +&gphy0 { + lantiq,gphy-mode = ; +}; + +&gphy1 { + lantiq,gphy-mode = ; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + mdio { + lantiq,groups = "mdio"; + lantiq,function = "mdio"; + }; + }; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x0800000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x0 0x30000>; + }; + + partition@30000 { + label = "uboot_env"; + reg = <0x30000 0x10000>; + }; + + partition@40000 { + label = "firmware"; + reg = <0x40000 0x750000>; + }; + + partition@790000 { + label = "ddrconfig"; + reg = <0x790000 0x70000>; + read-only; + }; + }; + }; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/BTHOMEHUBV2B.dts b/target/linux/lantiq/files/arch/mips/boot/dts/BTHOMEHUBV2B.dts new file mode 100644 index 0000000000..e126065ea6 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/BTHOMEHUBV2B.dts @@ -0,0 +1,263 @@ +/dts-v1/; + +#include "danube.dtsi" + +#include + +/ { + compatible = "bt,homehub-v2b", "lantiq,xway", "lantiq,danube"; + model = "BT Home Hub 2B"; /* SoC: Lantiq Danube-S PSB 50712 @ 333MHz V1.3/1.5 */ + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power_orange; + led-failsafe = &power_red; + led-running = &power_blue; + led-upgrade = &power_blue; + + led-dsl = &broadband_blue; + led-wifi = &wireless_blue; + }; + + memory@0 { /* RAM: Samsung K4H511638F-LC 64MB */ + reg = <0x0 0x4000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + reset { + label = "reset"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + findhandset { + label = "findhandset"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + wps { + label = "wps"; + gpios = <&gpio 22 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + upgrading-orange { + label = "bthomehubv2b:orange:upgrading"; + gpios = <&gpios 5 GPIO_ACTIVE_HIGH>; + }; + + phone-orange { + label = "bthomehubv2b:orange:phone"; + gpios = <&gpios 6 GPIO_ACTIVE_HIGH>; + }; + phone-blue { + label = "bthomehubv2b:blue:phone"; + gpios = <&gpios 7 GPIO_ACTIVE_HIGH>; + }; + + wireless-orange { + label = "bthomehubv2b:orange:wireless"; + gpios = <&gpios 8 GPIO_ACTIVE_HIGH>; + }; + wireless_blue: wireless-blue { + label = "bthomehubv2b:blue:wireless"; + gpios = <&gpios 9 GPIO_ACTIVE_HIGH>; + }; + + broadband-red { + label = "bthomehubv2b:red:broadband"; + gpios = <&gpios 10 GPIO_ACTIVE_HIGH>; + }; + broadband-orange { + label = "bthomehubv2b:orange:broadband"; + gpios = <&gpios 11 GPIO_ACTIVE_HIGH>; + }; + broadband_blue: broadband-blue { + label = "bthomehubv2b:blue:broadband"; + gpios = <&gpios 12 GPIO_ACTIVE_HIGH>; + }; + + power_red: power-red { + label = "bthomehubv2b:red:power"; + gpios = <&gpios 13 GPIO_ACTIVE_HIGH>; + }; + power_orange: power-orange { + label = "bthomehubv2b:orange:power"; + gpios = <&gpios 14 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + power_blue: power-blue { + label = "bthomehubv2b:blue:power"; + gpios = <&gpios 15 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + nand_out { + lantiq,groups = "nand cle", "nand ale"; + lantiq,function = "ebu"; + lantiq,output = <1>; + lantiq,open-drain = <0>; + lantiq,pull = <0>; + }; + nand_cs1 { + lantiq,groups = "nand cs1"; + lantiq,function = "ebu"; + lantiq,open-drain = <0>; + lantiq,pull = <0>; + }; + exin { + lantiq,groups = "exin1"; + lantiq,function = "exin"; + }; + pci_in { + lantiq,groups = "req1"; + lantiq,function = "pci"; + lantiq,output = <0>; + lantiq,open-drain = <1>; + lantiq,pull = <2>; + }; + pci_out { + lantiq,groups = "gnt1"; + lantiq,function = "pci"; + lantiq,output = <1>; + lantiq,open-drain = <0>; + lantiq,pull = <0>; + }; + + pci_rst { + lantiq,pins = "io21"; + lantiq,output = <1>; + lantiq,open-drain = <0>; + }; + + btn_in { + lantiq,pins = "io2", "io15", "io22"; + lantiq,output = <0>; + lantiq,open-drain = <1>; + lantiq,pull = <2>; + }; + }; +}; + +&gpios { + status = "okay"; +}; + +&gsw { + phy-mode = "rmii"; +}; + +&localbus { + nor@0 { /* NOR Flash: Spansion S29AL004D 512KB */ + compatible = "lantiq,nor"; /* "AMD AM29LV400BB" compatible on 3.3.8 */ + lantiq,cs = <0>; + bank-width = <2>; + reg = <0 0x0 0x80000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x00000 0x40000>; /* 256KB */ + }; + + partition@40000 { + label = "uboot_env"; + reg = <0x40000 0x10000>; /* 64KB */ + }; + + partition@50000 { + label = "rg_conf_1"; + reg = <0x50000 0x10000>; + }; + + partition@60000 { + label = "rg_conf_2"; + reg = <0x60000 0x10000>; + }; + + partition@70000 { + label = "rg_conf_factory"; + reg = <0x70000 0x10000>; + }; + }; + }; + + nand@1 { /* NAND Flash: Samsung K9F5608U0D-JIB0 32MB */ + compatible = "lantiq,nand-xway"; + lantiq,cs = <1>; + bank-width = <2>; + reg = <1 0x0 0x2000000 >; + #address-cells = <1>; + #size-cells = <1>; + req-mask = <0x1>; /* PCI request lines to mask during NAND access */ + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + ath9k_cal: partition@0 { + label = "art"; /* Atheros 9160 wifi b/g/n radio EEPROM */ + reg = <0x00000 0x4000>; + read-only; + }; + + partition@4000 { + label = "kernel"; + reg = <0x4000 0x200000>; + }; + + partition@164000 { + label = "ubi"; + reg = <0x204000 0x1DFC000>; + }; + }; + }; +}; + +&pci0 { + status = "okay"; + gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; + + wifi@168c,0027 { + compatible = "pci168c,0027"; + reg = <0x7000 0 0 0 0>; + qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:00:0e.0.bin */ + }; +}; + +&usb_phy { + status = "okay"; +}; + +&usb { + status = "okay"; +}; + +&vmmc { + status = "okay"; + gpios = <&gpio 31 GPIO_ACTIVE_HIGH>; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/BTHOMEHUBV3A.dts b/target/linux/lantiq/files/arch/mips/boot/dts/BTHOMEHUBV3A.dts new file mode 100644 index 0000000000..b854ac0a99 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/BTHOMEHUBV3A.dts @@ -0,0 +1,216 @@ +/dts-v1/; + +#include "ar9.dtsi" + +#include + +/ { + compatible = "bt,homehub-v3a", "lantiq,xway", "lantiq,ar9"; + model = "BT Home Hub 3A"; /* SoC: Lantiq ar9 @ 333MHz */ + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power_orange; + led-failsafe = &power_red; + led-running = &power_blue; + led-upgrade = &power_blue; + + led-dsl = &broadband_blue; + led-wifi = &wireless_blue; + }; + + memory@0 { /* RAM: Samsung K4H511638F-LC 64MB */ + reg = <0x0 0x4000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + reset { + label = "reset"; + gpios = <&gpio 54 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + restart { + label = "restart"; + gpios = <&gpio 52 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + wps { + label = "wps"; + gpios = <&gpio 53 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + wireless-red { + label = "bthomehubv3a:red:wireless"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + }; + wireless-orange { + label = "bthomehubv3a:orange:wireless"; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + }; + wireless_blue: wireless-blue { + label = "bthomehubv3a:blue:wireless"; + gpios = <&gpio 9 GPIO_ACTIVE_LOW>; + }; + + broadband-red { + label = "bthomehubv3a:red:broadband"; + gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + }; + broadband-orange { + label = "bthomehubv3a:orange:broadband"; + gpios = <&gpio 0 GPIO_ACTIVE_LOW>; + }; + broadband_blue: broadband-blue { + label = "bthomehubv3a:blue:broadband"; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + }; + + power_red: power-red { + label = "bthomehubv3a:red:power"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + }; + power_orange: power-orange { + label = "bthomehubv3a:orange:power"; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + power_blue: power-blue { + label = "bthomehubv3a:blue:power"; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + }; + }; + + usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio 33 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + nand_out { + lantiq,groups = "nand cle", "nand ale"; + lantiq,function = "ebu"; + lantiq,output = <1>; + lantiq,open-drain = <0>; + lantiq,pull = <0>; + }; + nand_cs1 { + lantiq,groups = "nand cs1"; + lantiq,function = "ebu"; + lantiq,open-drain = <0>; + lantiq,pull = <0>; + }; + + pci_in { + lantiq,groups = "req1"; + lantiq,function = "pci"; + lantiq,output = <0>; + lantiq,open-drain = <1>; + lantiq,pull = <2>; + }; + pci_out { + lantiq,groups = "gnt1"; + lantiq,function = "pci"; + lantiq,output = <1>; + lantiq,open-drain = <0>; + lantiq,pull = <0>; + }; + + pci_rst { + lantiq,pins = "io21"; + lantiq,output = <1>; + lantiq,open-drain = <0>; + }; + }; +}; + +&gsw { + phy-mode = "rgmii"; +}; + +&localbus { + nand@1 { /* NAND Flash: Samsung K9F5608U0D-JIB0 32MB */ + compatible = "lantiq,nand-xway"; + lantiq,cs = <1>; + bank-width = <2>; + reg = <1 0x0 0x2000000 >; + #address-cells = <1>; + #size-cells = <1>; + req-mask = <0x1>; /* PCI request lines to mask during NAND access */ + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "preboot"; + reg = <0x00000 0x8000>; + read-only; + }; + partition@8000 { + label = "u-boot"; + reg = <0x8000 0x05c000>; + read-only; + }; + partition@64000 { + label = "uboot_env"; + reg = <0x64000 0x004000>; + }; + ath9k_cal: partition@68000 { + label = "art-copy"; + reg = <0x68000 0x004000>; + }; + partition@6c000 { + label = "kernel"; + reg = <0x6c000 0x200000>; + }; + partition@26c000 { + label = "ubi"; + reg = <0x26c000 0x1d94000>; + }; + }; + }; +}; + +&pci0 { + status = "okay"; + gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; + + ath9k@7000 { + reg = <0x7000 0 0 0 0>; + qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:00:0e.0.bin */ + }; +}; + +&usb_phy0 { + status = "okay"; +}; + +&usb0 { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/BTHOMEHUBV5A.dts b/target/linux/lantiq/files/arch/mips/boot/dts/BTHOMEHUBV5A.dts new file mode 100644 index 0000000000..166eec3419 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/BTHOMEHUBV5A.dts @@ -0,0 +1,300 @@ +/dts-v1/; + +#include "vr9.dtsi" + +#include +#include + +/ { + compatible = "bt,homehub-v5a", "lantiq,xway", "lantiq,vr9"; + model = "BT Home Hub 5A"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power_green; + led-failsafe = &power_red; + led-running = &power_blue; + led-upgrade = &power_blue; + + led-dsl = &broadband_blue; + led-wifi = &wireless_blue; + }; + + memory@0 { + reg = <0x0 0x8000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + reset { + label = "reset"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&gpio 25 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + restart { + label = "restart"; + gpios = <&gpio 39 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + /* broadband-* is a single RGB led */ + broadband-red { + label = "bthomehubv5a:red:broadband"; + gpios = <&gpio 0 GPIO_ACTIVE_LOW>; + }; + broadband-green { + label = "bthomehubv5a:green:broadband"; + gpios = <&gpio 3 GPIO_ACTIVE_LOW>; + }; + broadband_blue: broadband-blue { + label = "bthomehubv5a:blue:broadband"; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + }; + + /* wireless-* is a single RGB led */ + wireless-red { + label = "bthomehubv5a:red:wireless"; + gpios = <&gpio 9 GPIO_ACTIVE_LOW>; + }; + wireless-green { + label = "bthomehubv5a:green:wireless"; + gpios = <&gpio 10 GPIO_ACTIVE_LOW>; + }; + wireless_blue: wireless-blue { + label = "bthomehubv5a:blue:wireless"; + gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + }; + + /* power-* is a single RGB led */ + power_red: power-red { + label = "bthomehubv5a:red:power"; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + }; + power_green: power-green { + label = "bthomehubv5a:green:power"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + power_blue: power-blue { + label = "bthomehubv5a:blue:power"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + }; + + dimmed { + label = "dimmed"; + gpios = <&gpio 19 GPIO_ACTIVE_HIGH>; + }; + }; + + usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio 33 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +ð0 { + lan: interface@0 { + compatible = "lantiq,xrx200-pdi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + lantiq,switch; + + ethernet@0 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <0>; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + }; + ethernet@1 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <1>; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + }; + ethernet@2 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <2>; + phy-mode = "gmii"; + phy-handle = <&phy11>; + }; + ethernet@4 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <4>; + phy-mode = "gmii"; + phy-handle = <&phy13>; + }; + ethernet@5 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <5>; + phy-mode = "rgmii"; + phy-handle = <&phy5>; + }; + }; + + mdio@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-mdio"; + reg = <0>; + + phy0: ethernet-phy@0 { + reg = <0x0>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + phy1: ethernet-phy@1 { + reg = <0x1>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + phy5: ethernet-phy@5 { + reg = <0x5>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + phy11: ethernet-phy@11 { + reg = <0x11>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + phy13: ethernet-phy@13 { + reg = <0x13>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + }; +}; + +&gphy0 { + lantiq,gphy-mode = ; +}; + +&gphy1 { + lantiq,gphy-mode = ; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + mdio { + lantiq,groups = "mdio"; + lantiq,function = "mdio"; + }; + pci_rst { + lantiq,pins = "io21"; + lantiq,output = <1>; + lantiq,open-drain; + }; + pcie_rst { + lantiq,pins = "io38"; + lantiq,pull = <0>; + lantiq,output = <1>; + lantiq,open-drain; + }; + usb_vbus { + lantiq,pins = "io33"; + lantiq,pull = <0>; + lantiq,open-drain = <0>; + lantiq,output = <1>; + }; + nand_out { + lantiq,groups = "nand cle", "nand ale"; + lantiq,function = "ebu"; + lantiq,output = <1>; + lantiq,open-drain = <0>; + lantiq,pull = <0>; + }; + nand_cs1 { + lantiq,groups = "nand cs1"; + lantiq,function = "ebu"; + lantiq,open-drain = <0>; + lantiq,pull = <0>; + }; + }; +}; + +&localbus { + nand@1 { + compatible = "lantiq,nand-xway"; + lantiq,cs = <1>; + bank-width = <2>; + reg = <0x1 0x0 0x2000000>; + #address-cells = <1>; + #size-cells = <1>; + nand-on-flash-bbt; + nand-ecc-strength = <3>; + nand-ecc-step-size = <256>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0xa0000>; + read-only; + }; + partition@a0000 { + label = "uboot-env"; + reg = <0xa0000 0x20000>; + read-only; + }; + partition@c0000 { + label = "unused"; + reg = <0xc0000 0x40000>; + }; + partition@100000 { + label = "ubi"; + reg = <0x100000 0x7e80000>; + }; + /* + * last 512 KiB are for the bad block table, not writable + */ + }; + }; +}; + +&pci0 { + status = "okay"; + gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; + + wifi@168c,002d { + compatible = "pci168c,002d"; + reg = <0x7000 0 0 0 0>; + qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:00:0e.0.bin */ + qca,disable-5ghz; + }; +}; + +&usb_phy0 { + status = "okay"; +}; + +&usb0 { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/DGN1000B.dts b/target/linux/lantiq/files/arch/mips/boot/dts/DGN1000B.dts new file mode 100644 index 0000000000..8c61e1b743 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/DGN1000B.dts @@ -0,0 +1,174 @@ +/dts-v1/; + +#include "amazonse.dtsi" + +#include + +/ { + compatible = "netgear,dgn1000b", "lantiq,xway", "lantiq,ase"; + model = "Netgear DGN1000B"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power; + led-failsafe = &power; + led-running = &power; + led-upgrade = &power; + + led-dsl = &dsl; + led-internet = &online_green; + }; + + memory@0 { + reg = <0x0 0x1000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + reset { + label = "reset"; + gpios = <&gpio 0 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + rfkill { + label = "rfkill"; + gpios = <&gpio 25 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + wps { + label = "wps"; + gpios = <&gpio 29 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + dsl: dsl { + label = "dgn1000b:green:dsl"; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + online_green: online { + label = "dgn1000b:green:online"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + online2 { + label = "dgn1000b:red:online"; + gpios = <&gpio 3 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + wps { + label = "dgn1000b:green:wps"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + power: power { + label = "dgn1000b:green:power"; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + /* + power red is missing + */ + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + asc { + lantiq,groups = "asc"; + lantiq,function = "asc"; + }; + keys_in { + lantiq,pins = "io0",/* "io25", */"io29"; + lantiq,pull = <2>; + lantiq,open-drain = <1>; + }; + }; + pins_spi_default: pins_spi_default { + spi_in { + lantiq,groups = "spi_di"; + lantiq,function = "spi"; + }; + spi_out { + lantiq,groups = "spi_do", "spi_clk", + "spi_cs1"; + lantiq,function = "spi"; + lantiq,output = <1>; + }; + }; +}; + +&gsw { + phy-mode = "mii"; + mac-address = [ 00 11 22 33 44 55 ]; +}; + +&spi { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pins_spi_default>; + + m25p80@1 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <1 0>; + spi-max-frequency = <5000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + reg = <0x0 0x20000>; + label = "SPI (RO) U-Boot Image"; + read-only; + }; + + partition@20000 { + reg = <0x20000 0x10000>; + label = "ENV_MAC"; + read-only; + }; + + partition@30000 { + reg = <0x30000 0x10000>; + label = "DPF"; + read-only; + }; + + partition@40000 { + reg = <0x40000 0x10000>; + label = "NVRAM"; + read-only; + }; + + partition@500000 { + reg = <0x50000 0x003a0000>; + label = "kernel"; + }; + }; + }; +}; + +&usb_phy { + status = "okay"; +}; + +&usb { + status = "okay"; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/DGN3500.dts b/target/linux/lantiq/files/arch/mips/boot/dts/DGN3500.dts new file mode 100644 index 0000000000..98a2ebd98e --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/DGN3500.dts @@ -0,0 +1,8 @@ +/dts-v1/; + +#include "DGN3500.dtsi" + +/ { + compatible = "netgear,dgn3500", "lantiq,xway", "lantiq,ar9"; + model = "Netgear DGN3500"; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/DGN3500.dtsi b/target/linux/lantiq/files/arch/mips/boot/dts/DGN3500.dtsi new file mode 100644 index 0000000000..b0facb4107 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/DGN3500.dtsi @@ -0,0 +1,214 @@ +#include "ar9.dtsi" + +#include + +/ { + chosen { + bootargs = "root= console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power_green; + led-failsafe = &power_red; + led-running = &power_green; + led-upgrade = &power_green; + + led-dsl = &dsl; + led-internet = &internet; + led-usb = &led_usb; + led-wifi = &wifi_green; + }; + + memory@0 { + reg = <0x0 0x4000000>; + }; + + rtl8366rb { + compatible = "realtek,rtl8366rb"; + gpio-sda = <&gpio 35 GPIO_ACTIVE_HIGH>; + gpio-sck = <&gpio 37 GPIO_ACTIVE_HIGH>; + + realtek,initvals = < + 0x0000 0x0830 + 0x0400 0x8130 + 0x000A 0x83ED + 0x0F51 0x0017 + 0x02F5 0x0048 + 0x02FA 0xFFDF + 0x02FB 0xFFE0 + 0x0450 0x0000 + 0x0401 0x0000 + 0x0431 0x0960 + >; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + rfkill { + label = "rfkill"; + gpios = <&gpio 36 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + wps { + label = "wps"; + gpios = <&gpio 54 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + reset { + label = "reset"; + gpios = <&gpio 53 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + internet: internet { + label = "dgn3500:green:internet"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + }; + internet2 { + label = "dgn3500:red:internet"; + gpios = <&gpio 30 GPIO_ACTIVE_LOW>; + }; + dsl: dsl { + label = "dgn3500:green:dsl"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + led_usb: usb { + label = "dgn3500:green:usb"; + gpios = <&gpio 22 GPIO_ACTIVE_LOW>; + }; + power_green: power { + label = "dgn3500:green:power"; + gpios = <&gpio 34 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + power_red: power2 { + label = "dgn3500:red:power"; + gpios = <&gpio 39 GPIO_ACTIVE_LOW>; + }; + wifi_green: wifi { + label = "dgn3500:green:wireless"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + }; + wifi2 { + label = "dgn3500:amber:wireless"; + gpios = <&gpio 51 GPIO_ACTIVE_LOW>; + }; + wps { + label = "dgn3500:green:wps"; + gpios = <&gpio 52 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + exin { + lantiq,groups = "exin1"; + lantiq,function = "exin"; + }; + pci { + lantiq,groups = "gnt1", "req1"; + lantiq,function = "pci"; + }; + pci-in { + lantiq,groups = "req1"; + lantiq,output = <0>; + lantiq,open-drain = <1>; + lantiq,pull = <2>; + }; + pci-out { + lantiq,groups = "gnt1"; + lantiq,output = <1>; + lantiq,pull = <0>; + }; + }; + pins_spi_default: pins_spi_default { + spi_in { + lantiq,groups = "spi_di"; + lantiq,function = "spi"; + }; + spi_out { + lantiq,groups = "spi_do", "spi_clk", + "spi_cs4"; + lantiq,function = "spi"; + lantiq,output = <1>; + }; + }; +}; + +&gsw { + phy-mode = "mii"; +}; + +&pci0 { + status = "okay"; + gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; + + wifi@168c,0029 { + compatible = "pci168c,0029"; + reg = <0x7000 0 0 0 0>; + qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:00:0e.0.bin */ + }; +}; + +&spi { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pins_spi_default>; + + m25p80@4 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <4 0>; + spi-max-frequency = <20000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + reg = <0x0 0x10000>; + label = "uboot"; + read-only; + }; + + partition@10000 { + reg = <0x10000 0x10000>; + label = "uboot-env"; + read-only; + }; + + ath9k_cal: partition@20000 { + reg = <0x20000 0x10000>; + label = "calibration"; + read-only; + }; + + partition@50000 { + reg = <0x50000 0xfa0000>; + label = "firmware"; + }; + }; + }; +}; + +&usb_phy0 { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/DGN3500B.dts b/target/linux/lantiq/files/arch/mips/boot/dts/DGN3500B.dts new file mode 100644 index 0000000000..d1d788cc7d --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/DGN3500B.dts @@ -0,0 +1,8 @@ +/dts-v1/; + +#include "DGN3500.dtsi" + +/ { + compatible = "netgear,dgn3500b", "lantiq,xway", "lantiq,ar9"; + model = "Netgear DGN3500B"; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/DM200.dts b/target/linux/lantiq/files/arch/mips/boot/dts/DM200.dts new file mode 100644 index 0000000000..8cf3456ee2 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/DM200.dts @@ -0,0 +1,217 @@ +/dts-v1/; + +#include "vr9.dtsi" + +#include +#include + +/ { + compatible = "netgear,dm200", "lantiq,xway", "lantiq,vr9"; + model = "Netgear DM200"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power_green; + led-failsafe = &power_amber; + led-running = &power_green; + led-upgrade = &power_green; + + led-dsl = &dsl_green; + }; + + memory@0 { + reg = <0x0 0x4000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + reset { + label = "reset"; + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio_export { + compatible = "gpio-export"; + #size-cells = <0>; + + annexa { + gpio-export,name = "annexa"; + gpio-export,output = <0>; + gpios = <&gpio 12 GPIO_ACTIVE_HIGH>; + }; + annexb { + gpio-export,name = "annexb"; + gpio-export,output = <0>; + gpios = <&gpio 15 GPIO_ACTIVE_HIGH>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + power_amber: power_amber { + label = "dm200:amber:power"; + gpios = <&gpio 0 GPIO_ACTIVE_HIGH>; + }; + power_green: power_green { + label = "dm200:green:power"; + gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; + }; + + lan_amber { + label = "dm200:amber:lan"; + gpios = <&gpio 33 GPIO_ACTIVE_HIGH>; + }; + lan_green { + label = "dm200:green:lan"; + gpios = <&gpio 11 GPIO_ACTIVE_HIGH>; + }; + + dsl_amber { + label = "dm200:amber:dsl"; + gpios = <&gpio 8 GPIO_ACTIVE_HIGH>; + }; + dsl_green: dsl_green { + label = "dm200:green:dsl"; + gpios = <&gpio 36 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +ð0 { + lantiq,phys = <&gphy1>; + + lan: interface@0 { + compatible = "lantiq,xrx200-pdi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + ethernet@4 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <4>; + phy-mode = "mii"; + phy-handle = <&phy13>; + }; + }; + + mdio@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-mdio"; + reg = <0>; + + phy13: ethernet-phy@13 { + reg = <0x13>; + compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; + }; + }; +}; + +&gphy1 { + lantiq,gphy-mode = ; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + mdio { + lantiq,groups = "mdio"; + lantiq,function = "mdio"; + }; + }; + + pins_spi_default: pins_spi_default { + spi_in { + lantiq,groups = "spi_di"; + lantiq,function = "spi"; + }; + spi_out { + lantiq,groups = "spi_do", "spi_clk", "spi_cs4"; + lantiq,function = "spi"; + lantiq,output = <1>; + }; + }; +}; + +&pcie0 { + status = "disabled"; +}; + +&spi { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pins_spi_default>; + + m25p80@4 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <4 0>; + spi-max-frequency = <10000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + reg = <0x0 0x20000>; + label = "uboot"; + read-only; + }; + + partition@20000 { + reg = <0x20000 0x10000>; + label = "gphyfirmware"; + read-only; + }; + + partition@30000 { + reg = <0x30000 0x7b0000>; + label = "firmware"; + }; + + partition@7e0000 { + reg = <0x7e0000 0x10000>; + label = "sysconfig"; + read-only; + }; + + partition@7f0000 { + reg = <0x7f0000 0x2000>; + label = "ubootconfig"; + read-only; + }; + + partition@7f2000 { + reg = <0x7f2000 0x1000>; + label = "ART"; + read-only; + }; + + partition@7f3000 { + reg = <0x7f3000 0x1000>; + label = "pot"; + read-only; + }; + + partition@7f4000 { + reg = <0x7f4000 0xc000>; + label = "ret"; + read-only; + }; + }; + }; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/EASY50712.dts b/target/linux/lantiq/files/arch/mips/boot/dts/EASY50712.dts new file mode 100644 index 0000000000..ec287ab40b --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/EASY50712.dts @@ -0,0 +1,81 @@ +/dts-v1/; + +#include "danube.dtsi" + +/ { + compatible = "lantiq,easy50712", "lantiq,xway", "lantiq,danube"; + model = "Intel EASY50712 Nand"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + memory@0 { + reg = <0x0 0x2000000>; + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + stp { + lantiq,groups = "stp"; + lantiq,function = "stp"; + }; + exin { + lantiq,groups = "exin1"; + lantiq,function = "exin"; + }; + pci { + lantiq,groups = "gnt1"; + lantiq,function = "pci"; + }; + conf_out { + lantiq,pins = "io4", "io5", "io6"; /* stp */ + lantiq,open-drain; + lantiq,pull = <0>; + }; + }; +}; + +&gsw { + phy-mode = "rmii"; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x2000000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x00000 0x10000>; /* 64 KB */ + }; + + partition@10000 { + label = "uboot_env"; + reg = <0x10000 0x10000>; /* 64 KB */ + }; + + partition@20000 { + label = "firmware"; + reg = <0x20000 0x3d0000>; + }; + + partition@400000 { + label = "rootfs"; + reg = <0x400000 0x400000>; + }; + }; + }; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/EASY50810.dts b/target/linux/lantiq/files/arch/mips/boot/dts/EASY50810.dts new file mode 100644 index 0000000000..21562dce21 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/EASY50810.dts @@ -0,0 +1,87 @@ +/dts-v1/; + +#include "ar9.dtsi" + +/ { + compatible = "lantiq,easy50810", "lantiq,xway", "lantiq,ar9"; + model = "Lantiq EASY50810"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + memory@0 { + reg = <0x0 0x2000000>; + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + stp { + lantiq,groups = "stp"; + lantiq,function = "stp"; + }; + exin { + lantiq,groups = "exin1"; + lantiq,function = "exin"; + }; + pci { + lantiq,groups = "gnt1"; + lantiq,function = "pci"; + }; + conf_out { + lantiq,pins = "io4", "io5", "io6"; /* stp */ + lantiq,open-drain; + lantiq,pull = <0>; + }; + }; +}; + +&gsw { + phy-mode = "rmii"; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x2000000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x00000 0x10000>; /* 64 KB */ + }; + + partition@10000 { + label = "uboot_env"; + reg = <0x10000 0x10000>; /* 64 KB */ + }; + + partition@20000 { + label = "firmware"; + reg = <0x20000 0x3d0000>; + }; + + partition@400000 { + label = "rootfs"; + reg = <0x400000 0x400000>; + }; + }; + }; +}; + +&stp { + status = "okay"; + lantiq,shadow = <0xfff>; + lantiq,groups = <0x3>; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/EASY80920.dtsi b/target/linux/lantiq/files/arch/mips/boot/dts/EASY80920.dtsi new file mode 100644 index 0000000000..781cdfdb5b --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/EASY80920.dtsi @@ -0,0 +1,313 @@ +#include "vr9.dtsi" + +#include +#include + +/ { + compatible = "lantiq,easy80920", "lantiq,xway", "lantiq,vr9"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power; + led-failsafe = &power; + led-running = &power; + led-upgrade = &power; + + led-usb = &led_usb1; + led-usb2 = &led_usb2; + }; + + memory@0 { + reg = <0x0 0x4000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; +/* reset { + label = "reset"; + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + linux,code = ; + };*/ + paging { + label = "paging"; + gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + power: power { + label = "easy80920:green:power"; + gpios = <&stp 9 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + warning { + label = "easy80920:green:warning"; + gpios = <&stp 22 GPIO_ACTIVE_HIGH>; + }; + fxs1 { + label = "easy80920:green:fxs1"; + gpios = <&stp 21 GPIO_ACTIVE_HIGH>; + }; + fxs2 { + label = "easy80920:green:fxs2"; + gpios = <&stp 20 GPIO_ACTIVE_HIGH>; + }; + fxo { + label = "easy80920:green:fxo"; + gpios = <&stp 19 GPIO_ACTIVE_HIGH>; + }; + led_usb1: usb1 { + label = "easy80920:green:usb1"; + gpios = <&stp 18 GPIO_ACTIVE_HIGH>; + }; + led_usb2: usb2 { + label = "easy80920:green:usb2"; + gpios = <&stp 15 GPIO_ACTIVE_HIGH>; + }; + sd { + label = "easy80920:green:sd"; + gpios = <&stp 14 GPIO_ACTIVE_HIGH>; + }; + wps { + label = "easy80920:green:wps"; + gpios = <&stp 12 GPIO_ACTIVE_HIGH>; + }; + }; + + usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio 33 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +ð0 { + lan: interface@0 { + compatible = "lantiq,xrx200-pdi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + lantiq,switch; + + ethernet@4 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <4>; + phy-mode = "gmii"; + phy-handle = <&phy13>; + }; + ethernet@2 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <2>; + phy-mode = "gmii"; + phy-handle = <&phy11>; + }; + ethernet@1 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <1>; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + }; + ethernet@0 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <0>; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + }; + }; + + wan: interface@1 { + compatible = "lantiq,xrx200-pdi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + lantiq,wan; + + ethernet@5 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <5>; + phy-mode = "rgmii"; + phy-handle = <&phy5>; + }; + }; + + mdio@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-mdio"; + reg = <0>; + + phy0: ethernet-phy@0 { + reg = <0x0>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + phy1: ethernet-phy@1 { + reg = <0x1>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + phy5: ethernet-phy@5 { + reg = <0x5>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + phy11: ethernet-phy@11 { + reg = <0x11>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + phy13: ethernet-phy@13 { + reg = <0x13>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + }; +}; + +&gphy0 { + lantiq,gphy-mode = ; +}; + +&gphy1 { + lantiq,gphy-mode = ; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + exin3 { + lantiq,groups = "exin3"; + lantiq,function = "exin"; + }; + stp { + lantiq,groups = "stp"; + lantiq,function = "stp"; + }; + nand { + lantiq,groups = "nand cle", "nand ale", + "nand rd", "nand rdy"; + lantiq,function = "ebu"; + }; + mdio { + lantiq,groups = "mdio"; + lantiq,function = "mdio"; + }; + pci { + lantiq,groups = "gnt1", "req1"; + lantiq,function = "pci"; + }; + conf_out { + lantiq,pins = "io24", "io13", "io49", /* nand cle, ale and rd */ + "io4", "io5", "io6", /* stp */ + "io21", + "io33"; + lantiq,open-drain; + lantiq,pull = <0>; + lantiq,output = <1>; + }; + pcie-rst { + lantiq,pins = "io38"; + lantiq,pull = <0>; + lantiq,output = <1>; + }; + conf_in { + lantiq,pins = "io39", /* exin3 */ + "io48"; /* nand rdy */ + lantiq,pull = <2>; + }; + }; + pins_spi_default: pins_spi_default { + spi_in { + lantiq,groups = "spi_di"; + lantiq,function = "spi"; + }; + spi_out { + lantiq,groups = "spi_do", "spi_clk", + "spi_cs4"; + lantiq,function = "spi"; + lantiq,output = <1>; + }; + }; +}; + +&spi { + pinctrl-names = "default"; + pinctrl-0 = <&pins_spi_default>; + + status = "okay"; + + m25p80@4 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <4 0>; + spi-max-frequency = <1000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + reg = <0x0 0x20000>; + label = "SPI (RO) U-Boot Image"; + read-only; + }; + + partition@20000 { + reg = <0x20000 0x10000>; + label = "ENV_MAC"; + read-only; + }; + + partition@30000 { + reg = <0x30000 0x10000>; + label = "DPF"; + read-only; + }; + + partition@40000 { + reg = <0x40000 0x10000>; + label = "NVRAM"; + read-only; + }; + + partition@500000 { + reg = <0x50000 0x003a0000>; + label = "kernel"; + }; + }; + }; +}; + +&stp { + status = "okay"; + + lantiq,shadow = <0xffff>; + lantiq,groups = <0x7>; + lantiq,dsl = <0x3>; + lantiq,phy1 = <0x7>; + lantiq,phy2 = <0x7>; + /* lantiq,rising; */ +}; + +&usb_phy0 { + status = "okay"; +}; + +&usb0 { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/EASY80920NAND.dts b/target/linux/lantiq/files/arch/mips/boot/dts/EASY80920NAND.dts new file mode 100644 index 0000000000..0134a7c177 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/EASY80920NAND.dts @@ -0,0 +1,65 @@ +/dts-v1/; + + +#include "EASY80920.dtsi" + +/ { + compatible = "lantiq,easy80920-nand", "lantiq,easy80920", "lantiq,xway", "lantiq,vr9"; + model = "Intel EASY80920 Nand"; + + chosen { + bootargs = "ubi.mtd=ubi ubi.block=0,rootfsA root=/dev/ubiblock0_1"; + }; +}; + +&localbus { + nand@0 { + compatible = "lantiq,nand-xway"; + lantiq,cs = <1>; + bank-width = <2>; + reg = <0 0x0 0x2000000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x00000 0x100000>; /* 1024 KB */ + }; + + partition@100000 { + label = "uboot_env"; + reg = <0x100000 0x40000>; /* 256 KB */ + }; + + partition@140000 { + label = "ubootconfigB"; + reg = <0x140000 0x40000>; /* 256 KB */ + }; + + partition@180000 { + label = "gphyfirmware"; + reg = <0x180000 0x40000>; /* 256 KB */ + }; + + partition@1c0000 { + label = "ubi"; + reg = <0x1c0000 0xc800000>; + }; + + partition@c9c0000 { + label = "calibration"; + reg = <0xc9c0000 0x100000>; + }; + + partition@cac0000 { + label = "res"; + reg = <0xcac0000 0x13540000>; + }; + }; + }; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/EASY80920NOR.dts b/target/linux/lantiq/files/arch/mips/boot/dts/EASY80920NOR.dts new file mode 100644 index 0000000000..9adc0b4f92 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/EASY80920NOR.dts @@ -0,0 +1,39 @@ +/dts-v1/; + +#include "EASY80920.dtsi" + +/ { + compatible = "lantiq,easy80920-nor", "lantiq,easy80920", "lantiq,xway", "lantiq,vr9"; + model = "Intel EASY80920 Nor"; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x2000000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x00000 0x10000>; + }; + + partition@10000 { + label = "uboot_env"; + reg = <0x10000 0x10000>; + }; + + partition@20000 { + label = "firmware"; + reg = <0x20000 0x7e0000>; + }; + }; + }; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/EASY88388.dts b/target/linux/lantiq/files/arch/mips/boot/dts/EASY88388.dts new file mode 100644 index 0000000000..86f3b47c6b --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/EASY88388.dts @@ -0,0 +1,93 @@ +/dts-v1/; + +#include +#include "falcon.dtsi" +#include "falcon-sflash-16M.dtsi" + +/ { + model = "Lantiq Falcon FTTDP8 Reference Board"; + compatible = "lantiq,easy88388", "lantiq,falcon"; + + aliases { + spi0 = &ebu_cs0; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x4000000>; // 64M at 0x0 + }; + + gpio-keys { + compatible = "gpio-keys"; + reset { + label = "reset"; + gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; + linux,code = <0x198>; + }; + }; + + pinctrl { + led_pins: led-pins { + lantiq,pins = "io34", "io35", "io36", "io37", "io38", + "io39", "io40", "io41"; + lantiq,function = "gpio"; + }; + }; + + easy88388-leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins &bootled_pins>; + + GPON { + label = "easy88388:green:gpon"; + gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; + }; + TEST { + label = "easy88388:green:test"; + gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; + }; + STATUS { + label = "easy88388:green:status"; + gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; + }; + ERROR { + label = "easy88388:red:error"; + gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; + }; + + DSL1 { + label = "easy88388:dsl:1"; + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; + }; + DSL2 { + label = "easy88388:dsl:2"; + gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; + }; + DSL3 { + label = "easy88388:dsl:3"; + gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; + }; + DSL4 { + label = "easy88388:dsl:4"; + gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; + }; + DSL5 { + label = "easy88388:dsl:5"; + gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>; + }; + DSL6 { + label = "easy88388:dsl:6"; + gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; + }; + DSL7 { + label = "easy88388:dsl:7"; + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; + }; + DSL8 { + label = "easy88388:dsl:8"; + gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; + }; + }; +}; + diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/EASY88444.dts b/target/linux/lantiq/files/arch/mips/boot/dts/EASY88444.dts new file mode 100644 index 0000000000..e1a934fc47 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/EASY88444.dts @@ -0,0 +1,72 @@ +/dts-v1/; + +#include +#include "falcon.dtsi" +#include "falcon-sflash-16M.dtsi" + +/ { + model = "Lantiq Falcon FTTdp G.FAST Reference Board"; + compatible = "lantiq,easy88444", "lantiq,falcon"; + + aliases { + spi0 = &ebu_cs0; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x4000000>; // 64M at 0x0 + }; + + gpio-keys { + compatible = "gpio-keys"; + reset { + label = "reset"; + gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; + linux,code = <0x198>; + }; + }; + + pinctrl { + led_pins: led-pins { + lantiq,pins = "io34", "io35", "io37"; + lantiq,function = "gpio"; + }; + }; + + easy88444-leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins &bootled_pins>; + + GPON { + label = "easy88444:green:gpon"; + gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; + }; + TEST { + label = "easy88444:green:test"; + gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; + }; + STATUS { + label = "easy88444:green:status"; + gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; + }; + + GFAST1 { + label = "easy88444:gfast:1"; + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; + }; + GFAST2 { + label = "easy88444:gfast:2"; + gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; + }; + GFAST3 { + label = "easy88444:gfast:3"; + gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; + }; + GFAST4 { + label = "easy88444:gfast:4"; + gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; + }; + }; +}; + diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/EASY98000-base.dtsi b/target/linux/lantiq/files/arch/mips/boot/dts/EASY98000-base.dtsi new file mode 100644 index 0000000000..cfe1140ac1 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/EASY98000-base.dtsi @@ -0,0 +1,110 @@ + +#include +#include + +/ { + compatible = "lantiq,easy98000", "lantiq,falcon"; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x4000000>; + }; + + easy98000-leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&bootled_pins>; + + LED_0 { + label = "easy98000:green:gpon"; + gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + LED_1 { + label = "easy98000:red:gpon"; + gpios = <&gpio0 10 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + LED_2 { + label = "easy98000:green:gpon_tx"; + gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + LED_3 { + label = "easy98000:green:gpon_rx"; + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + LED_4 { + label = "easy98000:green:voice"; + gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + LED_5 { + label = "easy98000:green:status"; + gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + }; +}; + +&ebu_cs1 { + eth0: ethernet@0000000 { + compatible = "davicom,dm9000"; + device_type = "network"; + reg = <0x0000003 0x1>, <0x0000001 0x1>; + reg-names = "addr", "data"; + interrupt-parent = <&gpio1>; + #interrupt-cells = <2>; + interrupts = <10 IRQ_TYPE_LEVEL_LOW>; + local-mac-address = [ 00 00 00 00 00 00 ]; + }; + + cpld@3c00000 { + compatible = "lantiq,easy98000_addon"; + reg = <0x3c00000 0x2>; + }; + + cpld@3c0000c { + compatible = "lantiq,easy98000_cpld_led"; + reg = <0x3c0000c 0x2>, <0x3c00012 0x2>; + }; +}; + +/* // enable this for second uart: +&serial1 { + status = "okay"; +};*/ + +&spi { + status = "okay"; + + eeprom@1 { + compatible = "atmel,at25", "atmel,at25160n"; + reg = <2>; + spi-max-frequency = <1000000>; + spi-cpha; + spi-cpol; + + pagesize = <32>; + size = <2048>; + address-width = <16>; + }; +}; + +&i2c { + status = "okay"; + + clock-frequency = <100000>; + + /* eeprom-emulation by OMU */ + eeprom@50 { + compatible = "at,24c02"; + reg = <0x50>; + }; + eeprom@51 { + compatible = "at,24c02"; + reg = <0x51>; + }; +}; + diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/EASY98000NAND.dts b/target/linux/lantiq/files/arch/mips/boot/dts/EASY98000NAND.dts new file mode 100644 index 0000000000..a40cef3931 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/EASY98000NAND.dts @@ -0,0 +1,40 @@ +/dts-v1/; + +#include "falcon.dtsi" +#include "EASY98000-base.dtsi" + +/ { + model = "Lantiq Falcon (NAND)"; + compatible = "lantiq,easy98000-nand", "lantiq,easy98000", "lantiq,falcon"; + + aliases { + spi0 = &spi; + }; +}; + +&ebu_cs0 { + gen_nand@0 { + compatible = "gen_nand", "lantiq,nand-falcon"; + bank-width = <1>; + reg = <0x0 0x40000>; + #address-cells = <1>; + #size-cells = <1>; + linux,mtd-name = "gen_nand"; + bbt-use-flash; + + partition@0 { + label = "uboot"; + reg = <0x00000 0x40000>; + }; + + partition@10000 { + label = "uboot_env"; + reg = <0x40000 0x40000>; + }; + + partition@20000 { + label = "linux"; + reg = <0x80000 0x3d0000>; + }; + }; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/EASY98000NOR.dts b/target/linux/lantiq/files/arch/mips/boot/dts/EASY98000NOR.dts new file mode 100644 index 0000000000..ad53bf96e9 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/EASY98000NOR.dts @@ -0,0 +1,38 @@ +/dts-v1/; + +#include "falcon.dtsi" +#include "EASY98000-base.dtsi" + +/ { + model = "Lantiq Falcon (NOR)"; + compatible = "lantiq,easy98000-nor", "lantiq,easy98000", "lantiq,falcon"; + + aliases { + spi0 = &spi; + }; +}; + +&ebu_cs0 { + cfi@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0x0 0x4000000>; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x00000 0x40000>; + }; + + partition@10000 { + label = "uboot_env"; + reg = <0x40000 0x40000>; + }; + + partition@20000 { + label = "linux"; + reg = <0x80000 0x3d0000>; + }; + }; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/EASY98000SFLASH.dts b/target/linux/lantiq/files/arch/mips/boot/dts/EASY98000SFLASH.dts new file mode 100644 index 0000000000..bbe524e94e --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/EASY98000SFLASH.dts @@ -0,0 +1,16 @@ +/dts-v1/; + +#include "falcon.dtsi" +#include "EASY98000-base.dtsi" +#include "falcon-sflash-16M.dtsi" + +/ { + model = "Lantiq Falcon (SFLASH)"; + compatible = "lantiq,easy98000-sflash", "lantiq,easy98000", "lantiq,falcon"; + + aliases { + spi0 = &ebu_cs0; + spi1 = &spi; + }; +}; + diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/EASY98020.dts b/target/linux/lantiq/files/arch/mips/boot/dts/EASY98020.dts new file mode 100644 index 0000000000..b66786a2ce --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/EASY98020.dts @@ -0,0 +1,91 @@ +/dts-v1/; + +#include + +#include "falcon.dtsi" +#include "falcon-sflash-16M.dtsi" + +/ { + model = "Lantiq Falcon Reference Board"; + compatible = "lantiq,easy98020", "lantiq,falcon"; + + aliases { + spi0 = &ebu_cs0; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x4000000>; // 64M at 0x0 + }; + + gpio-keys { + compatible = "gpio-keys"; + reset { + label = "reset"; + gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; + linux,code = <0x198>; + }; + }; + + pinctrl { + led_pins: phy-led-pins { + lantiq,pins = "io42", "io41", "io38", "io37"; + lantiq,function = "gpio"; + }; + }; + + easy98020-leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&bootled_pins>; + + GPON { + label = "easy98020:green:gpon"; + gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + TEST { + label = "easy98020:green:test"; + gpios = <&gpio0 10 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + ETH { + label = "easy98020:green:status"; + gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + VOICE { + label = "easy98020:green:voice"; + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + VIDEO { + label = "easy98020:green:video"; + gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + }; + + easy98020-phy-leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins>; + + GE0_ACT { + label = "easy98020:ge0_act"; + gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; + }; + GE0_LINK { + label = "easy98020:ge0_link"; + gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; + }; + GE1_ACT { + label = "easy98020:ge1_act"; + gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; + }; + GE1_LINK { + label = "easy98020:ge1_link"; + gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; + }; + }; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/EASY98020V18.dts b/target/linux/lantiq/files/arch/mips/boot/dts/EASY98020V18.dts new file mode 100644 index 0000000000..9aa1be91ed --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/EASY98020V18.dts @@ -0,0 +1,68 @@ +/dts-v1/; + +#include + +#include "falcon.dtsi" +#include "falcon-sflash-16M.dtsi" + +/ { + model = "Lantiq Falcon Reference Board V1.8"; + compatible = "lantiq,easy98020-v18", "lantiq,easy98020", "lantiq,falcon"; + + aliases { + spi0 = &ebu_cs0; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x4000000>; // 64M at 0x0 + }; + + gpio-keys { + compatible = "gpio-keys"; + reset { + label = "reset"; + gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; + linux,code = <0x198>; + }; + }; + + pinctrl { + led_pins: led-pins { + lantiq,pins = "io11", "io14", "io36", "io37", "io38"; + lantiq,function = "gpio"; + }; + }; + + easy98020-leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins &bootled_pins>; + + GPON { + label = "easy98020:green:gpon"; + gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + TEST { + label = "easy98020:green:test"; + gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + ETH { + label = "easy98020:green:status"; + gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + VOICE { + label = "easy98020:green:voice"; + gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + VIDEO { + label = "easy98020:green:video"; + gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + }; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/EASY98021.dts b/target/linux/lantiq/files/arch/mips/boot/dts/EASY98021.dts new file mode 100644 index 0000000000..38154d6f1c --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/EASY98021.dts @@ -0,0 +1,81 @@ +/dts-v1/; + +#include + +#include "falcon.dtsi" +#include "falcon-sflash-16M.dtsi" + +/ { + model = "Lantiq Falcon HGU Reference Board"; + compatible = "lantiq,easy98021", "lantiq,easy98020", "lantiq,falcon"; + + aliases { + spi0 = &ebu_cs0; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x4000000>; // 64M at 0x0 + }; + + gpio-keys { + compatible = "gpio-keys"; + reset { + label = "reset"; + gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; + linux,code = <0x198>; + }; + }; + + gpio-mmc { + /* Place-holder for SIM-Card connector, + to list the used GPIOs, no official binding */ + compatible = "gpio-mmc"; + gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>, + <&gpio0 3 GPIO_ACTIVE_HIGH>, + <&gpio0 2 GPIO_ACTIVE_HIGH>, + <0>; /* no CS */ + gpio-names = "di", "do", "clk", "cs"; + reset-gpio = <&gpio3 24 GPIO_ACTIVE_HIGH>; + }; + + pinctrl { + led_pins: led-pins { + lantiq,pins = "io11", "io14", "io36", "io37", "io38"; + lantiq,function = "gpio"; + }; + }; + + easy98021-leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins &bootled_pins>; + + GPON { + label = "easy98021:green:gpon"; + gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + TEST { + label = "easy98021:red:test"; + gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + ETH { + label = "easy98021:green:status"; + gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + VOICE { + label = "easy98021:green:voice"; + gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + SIMCARD { + label = "easy98021:green:simcard"; + gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + }; +}; + diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/EASY98035SYNCE.dts b/target/linux/lantiq/files/arch/mips/boot/dts/EASY98035SYNCE.dts new file mode 100644 index 0000000000..df941cdb67 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/EASY98035SYNCE.dts @@ -0,0 +1,76 @@ +/dts-v1/; + +#include "falcon.dtsi" +#include "falcon-sflash-16M.dtsi" + +/ { + model = "Lantiq Falcon SFP Stick with SyncE"; + compatible = "lantiq,easy98035synce", "lantiq,falcon-sfp", "lantiq,falcon"; + + aliases { + spi0 = &ebu_cs0; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x4000000>; // 64M at 0x0 + }; + + pinctrl { + compatible = "lantiq,pinctrl-falcon"; + + asc0_func1: func1 { + func1_tx { + lantiq,pins = "io32"; + lantiq,mux = <1>; + lantiq,input = <0>; + }; + func1_rx { + lantiq,pins = "io33"; + lantiq,mux = <0>; + }; + }; + asc0_func2: func2 { + func2_tx { + lantiq,pins = "io32"; + lantiq,mux = <0>; + }; + func2_rx { + lantiq,pins = "io33"; + lantiq,mux = <1>; + lantiq,input = <0>; + }; + }; + asc0_func3: func3 { + func3_tx { + lantiq,pins = "io32"; + lantiq,mux = <1>; + lantiq,input = <0>; + }; + func3_rx { + lantiq,pins = "io33"; + lantiq,mux = <1>; + lantiq,input = <0>; + }; + }; + }; + + pinselect-asc0 { + compatible = "lantiq,pinselect-asc0"; + pinctrl-names = "asc0", "func1", "func2", "func3"; + pinctrl-0 = <&asc0_pins>; + pinctrl-1 = <&asc0_func1>; + pinctrl-2 = <&asc0_func2>; + pinctrl-3 = <&asc0_func3>; + }; +}; + +&serial0 { + pinctrl-names = "default"; + /* use "empty" pinctrl to leave setting from u-boot enabled */ + pinctrl-0 = < >; +}; + +&i2c { + status = "okay"; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/EASY98035SYNCE1588.dts b/target/linux/lantiq/files/arch/mips/boot/dts/EASY98035SYNCE1588.dts new file mode 100644 index 0000000000..a3abc6e707 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/EASY98035SYNCE1588.dts @@ -0,0 +1,76 @@ +/dts-v1/; + +#include "falcon.dtsi" +#include "falcon-sflash-16M.dtsi" + +/ { + model = "Lantiq Falcon SFP Stick with SyncE/1588"; + compatible = "lantiq,easy98035synce1588", "lantiq,falcon-sfp", "lantiq,falcon"; + + aliases { + spi0 = &ebu_cs0; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x4000000>; // 64M at 0x0 + }; + + pinctrl { + compatible = "lantiq,pinctrl-falcon"; + + asc0_func1: func1 { + func1_tx { + lantiq,pins = "io32"; + lantiq,mux = <1>; + lantiq,input = <0>; + }; + func1_rx { + lantiq,pins = "io33"; + lantiq,mux = <0>; + }; + }; + asc0_func2: func2 { + func2_tx { + lantiq,pins = "io32"; + lantiq,mux = <0>; + }; + func2_rx { + lantiq,pins = "io33"; + lantiq,mux = <1>; + lantiq,input = <0>; + }; + }; + asc0_func3: func3 { + func3_tx { + lantiq,pins = "io32"; + lantiq,mux = <1>; + lantiq,input = <0>; + }; + func3_rx { + lantiq,pins = "io33"; + lantiq,mux = <1>; + lantiq,input = <0>; + }; + }; + }; + + pinselect-asc0 { + compatible = "lantiq,pinselect-asc0"; + pinctrl-names = "asc0", "func1", "func2", "func3"; + pinctrl-0 = <&asc0_pins>; + pinctrl-1 = <&asc0_func1>; + pinctrl-2 = <&asc0_func2>; + pinctrl-3 = <&asc0_func3>; + }; +}; + +&serial0 { + pinctrl-names = "default"; + /* use "empty" pinctrl to leave setting from u-boot enabled */ + pinctrl-0 = < >; +}; + +&i2c { + status = "okay"; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/FALCON-MDU.dts b/target/linux/lantiq/files/arch/mips/boot/dts/FALCON-MDU.dts new file mode 100644 index 0000000000..6710bbe98e --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/FALCON-MDU.dts @@ -0,0 +1,53 @@ +/dts-v1/; + +#include + +#include "falcon.dtsi" +#include "falcon-sflash-16M.dtsi" + +/ { + model = "Lantiq Falcon / Vinax MDU Board"; + compatible = "lantiq,falcon-mdu", "lantiq,falcon"; + + aliases { + spi0 = &ebu_cs0; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x4000000>; // 64M at 0x0 + }; + + mdu-leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&bootled_pins>; + + LED_0 { + label = "mdu:green:gpon"; + gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + LED_1 { + label = "mdu:green:status"; + gpios = <&gpio0 10 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + LED_2 { + label = "mdu:green:2"; + gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + LED_3 { + label = "mdu:green:3"; + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + LED_4 { + label = "mdu:green:4"; + gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; + default-state = "keep"; + }; + }; +}; + diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/FALCON-SFP.dts b/target/linux/lantiq/files/arch/mips/boot/dts/FALCON-SFP.dts new file mode 100644 index 0000000000..8d45de4ebe --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/FALCON-SFP.dts @@ -0,0 +1,76 @@ +/dts-v1/; + +#include "falcon.dtsi" +#include "falcon-sflash-16M.dtsi" + +/ { + model = "Lantiq Falcon SFP Stick"; + compatible = "lantiq,falcon-sfp", "lantiq,falcon"; + + aliases { + spi0 = &ebu_cs0; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x4000000>; // 64M at 0x0 + }; + + pinctrl { + compatible = "lantiq,pinctrl-falcon"; + + asc0_func1: func1 { + func1_tx { + lantiq,pins = "io32"; + lantiq,mux = <1>; + lantiq,output = <0>; + }; + func1_rx { + lantiq,pins = "io33"; + lantiq,mux = <0>; + }; + }; + asc0_func2: func2 { + func2_tx { + lantiq,pins = "io32"; + lantiq,mux = <0>; + }; + func2_rx { + lantiq,pins = "io33"; + lantiq,mux = <1>; + lantiq,input = <0>; + }; + }; + asc0_func3: func3 { + func3_tx { + lantiq,pins = "io32"; + lantiq,mux = <1>; + lantiq,output = <0>; + }; + func3_rx { + lantiq,pins = "io33"; + lantiq,mux = <1>; + lantiq,input = <0>; + }; + }; + }; + + pinselect-asc0 { + compatible = "lantiq,pinselect-asc0"; + pinctrl-names = "asc0", "func1", "func2", "func3"; + pinctrl-0 = <&asc0_pins>; + pinctrl-1 = <&asc0_func1>; + pinctrl-2 = <&asc0_func2>; + pinctrl-3 = <&asc0_func3>; + }; +}; + +&serial0 { + pinctrl-names = "default"; + /* use "empty" pinctrl to leave setting from u-boot enabled */ + pinctrl-0 = < >; +}; + +&i2c { + status = "okay"; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/FRITZ3370-REV2-HYNIX.dts b/target/linux/lantiq/files/arch/mips/boot/dts/FRITZ3370-REV2-HYNIX.dts new file mode 100644 index 0000000000..ebd6f6e4c8 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/FRITZ3370-REV2-HYNIX.dts @@ -0,0 +1,38 @@ +/dts-v1/; + +#include "FRITZ3370-REV2.dtsi" + +/ { + compatible = "avm,fritz3370-rev2-hynix", "avm,fritz3370-rev2", "lantiq,xway", "lantiq,vr9"; + model = "AVM FRITZ!Box 3370 Rev. 2 (Hynix NAND)"; +}; + +&localbus { + nand@1 { + compatible = "lantiq,nand-xway"; + bank-width = <2>; + reg = <1 0x0 0x2000000>; + #address-cells = <1>; + #size-cells = <1>; + + nand-ecc-mode = "soft"; + nand-ecc-strength = <3>; + nand-ecc-step-size = <256>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "kernel"; + reg = <0x0 0x400000>; + }; + + partition@400000 { + label = "ubi"; + reg = <0x400000 0x7c00000>; + }; + }; + }; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/FRITZ3370-REV2-MICRON.dts b/target/linux/lantiq/files/arch/mips/boot/dts/FRITZ3370-REV2-MICRON.dts new file mode 100644 index 0000000000..dcc97d2808 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/FRITZ3370-REV2-MICRON.dts @@ -0,0 +1,36 @@ +/dts-v1/; + +#include "FRITZ3370-REV2.dtsi" + +/ { + compatible = "avm,fritz3370-rev2-micron", "avm,fritz3370-rev2", "lantiq,xway", "lantiq,vr9"; + model = "AVM FRITZ!Box 3370 Rev. 2 (Micron NAND)"; +}; + +&localbus { + nand@1 { + compatible = "lantiq,nand-xway"; + bank-width = <2>; + reg = <1 0x0 0x2000000>; + #address-cells = <1>; + #size-cells = <1>; + + nand-ecc-mode = "on-die"; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "kernel"; + reg = <0x0 0x400000>; + }; + + partition@400000 { + label = "ubi"; + reg = <0x400000 0x7c00000>; + }; + }; + }; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/FRITZ3370-REV2.dtsi b/target/linux/lantiq/files/arch/mips/boot/dts/FRITZ3370-REV2.dtsi new file mode 100644 index 0000000000..9a0359d1cc --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/FRITZ3370-REV2.dtsi @@ -0,0 +1,306 @@ +#include "vr9.dtsi" + +#include +#include + +/ { + compatible = "avm,fritz3370-rev2", "lantiq,xway", "lantiq,vr9"; + model = "AVM FRITZ!Box 3370 Rev. 2"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power_green; + led-failsafe = &power_red; + led-running = &power_green; + led-upgrade = &power_green; + + led-dsl = &dsl; + led-internet = &info_green; + led-wifi = &wifi; + }; + + memory@0 { + reg = <0x0 0x8000000>; + }; + + gpio-poweroff { + compatible = "gpio-poweroff"; + gpios = <&gpio 45 GPIO_ACTIVE_HIGH>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + power { + label = "power"; + gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; + linux,code = ; + }; + + wifi { + label = "wlan"; + gpios = <&gpio 29 GPIO_ACTIVE_HIGH>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + power_green: power { + label = "fritz3370:green:power"; + gpios = <&gpio 32 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + + power_red: power2 { + label = "fritz3370:red:power"; + gpios = <&gpio 33 GPIO_ACTIVE_LOW>; + }; + + info_red { + label = "fritz3370:red:info"; + gpios = <&gpio 34 GPIO_ACTIVE_LOW>; + }; + + wifi: wifi { + label = "fritz3370:green:wlan"; + gpios = <&gpio 35 GPIO_ACTIVE_LOW>; + }; + + dsl: dsl { + label = "fritz3370:green:dsl"; + gpios = <&gpio 36 GPIO_ACTIVE_LOW>; + }; + + lan { + label = "fritz3370:green:lan"; + gpios = <&gpio 38 GPIO_ACTIVE_LOW>; + }; + + info_green: info_green { + label = "fritz3370:green:info"; + gpios = <&gpio 47 GPIO_ACTIVE_LOW>; + }; + }; + + usb0_vbus: regulator-usb0-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB0_VBUS"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio 14 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + usb1_vbus: regulator-usb1-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB1_VBUS"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio 5 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +ð0 { + lan: interface@0 { + compatible = "lantiq,xrx200-pdi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + lantiq,switch; + + ethernet@0 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <0>; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + gpios = <&gpio 37 GPIO_ACTIVE_HIGH>; + }; + + ethernet@1 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <1>; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + gpios = <&gpio 44 GPIO_ACTIVE_HIGH>; + }; + + ethernet@2 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <2>; + phy-mode = "gmii"; + phy-handle = <&phy11>; + }; + + ethernet@4 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <4>; + phy-mode = "gmii"; + phy-handle = <&phy13>; + }; + }; + + mdio@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-mdio"; + reg = <0>; + + phy0: ethernet-phy@0 { + reg = <0x0>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + + phy1: ethernet-phy@1 { + reg = <0x1>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + + phy11: ethernet-phy@11 { + reg = <0x11>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + + phy13: ethernet-phy@13 { + reg = <0x13>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + }; +}; + +&gphy0 { + lantiq,gphy-mode = ; +}; + +&gphy1 { + lantiq,gphy-mode = ; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + mdio { + lantiq,groups = "mdio"; + lantiq,function = "mdio"; + }; + + nand { + lantiq,groups = "nand cle", "nand ale", + "nand rd", "nand cs1", "nand rdy"; + lantiq,function = "ebu"; + lantiq,pull = <1>; + }; + + phy-rst { + lantiq,pins = "io37", "io44"; + lantiq,pull = <0>; + lantiq,open-drain = <0>; + lantiq,output = <1>; + }; + + pcie-rst { + lantiq,pins = "io21"; + lantiq,pull = <0>; + lantiq,output = <1>; + }; + }; + + pins_spi_default: pins_spi_default { + spi_in { + lantiq,groups = "spi_di"; + lantiq,function = "spi"; + }; + + spi_out { + lantiq,groups = "spi_do", "spi_clk", + "spi_cs4"; + lantiq,function = "spi"; + lantiq,output = <1>; + }; + }; +}; + +&pcie0 { + gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; + + pcie@0 { + reg = <0 0 0 0 0>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + device_type = "pci"; + + wifi@0,0 { + compatible = "pci0,0"; + reg = <0 0 0 0 0>; + qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:01:00.0.bin */ + }; + }; +}; + +&spi { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pins_spi_default>; + + m25p80@4 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <4 0>; + spi-max-frequency = <1000000>; + + urlader: partition@0 { + reg = <0x0 0x20000>; + label = "urlader"; + read-only; + }; + + partition@20000 { + reg = <0x20000 0x10000>; + label = "tffs (1)"; + read-only; + }; + + partition@30000 { + reg = <0x30000 0x10000>; + label = "tffs (2)"; + read-only; + }; + }; +}; + +&usb_phy0 { + status = "okay"; +}; + +&usb_phy1 { + status = "okay"; +}; + +&usb0 { + status = "okay"; + vbus-supply = <&usb0_vbus>; +}; + +&usb1 { + status = "okay"; + vbus-supply = <&usb1_vbus>; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/FRITZ7312.dts b/target/linux/lantiq/files/arch/mips/boot/dts/FRITZ7312.dts new file mode 100644 index 0000000000..796b941ede --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/FRITZ7312.dts @@ -0,0 +1,182 @@ +/dts-v1/; + +#include "ar9.dtsi" + +#include + +/ { + compatible = "avm,fritz7312", "lantiq,xway", "lantiq,ar9"; + model = "AVM FRITZ!Box 7312"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power; + led-failsafe = &power; + led-running = &power; + led-upgrade = &power; + + led-internet = &info_green; + led-dsl = &power; + led-wifi = &wlan; + }; + + memory@0 { + reg = <0x0 0x4000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + wlan { + label = "wlan"; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + dect { + label = "dect"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + power: power { + label = "fritz7312:green:power"; + gpios = <&gpio 44 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + voice { + label = "fritz7312:green:fon"; + gpios = <&gpio 47 GPIO_ACTIVE_LOW>; + }; + dect { + label = "fritz7312:green:dect"; + gpios = <&gpio 38 GPIO_ACTIVE_LOW>; + }; + wlan: wlan { + label = "fritz7312:green:wlan"; + gpios = <&gpio 37 GPIO_ACTIVE_LOW>; + }; + info_green: info_green { + label = "fritz7312:green:info"; + gpios = <&gpio 35 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + pci { + lantiq,groups = "gnt1", "req1", "req2", "req4", "gnt2", "gnt3", "gnt4"; + lantiq,function = "pci"; + }; + pci-in { + lantiq,groups = "req1", "req2", "req4"; + lantiq,output = <0>; + lantiq,open-drain = <1>; + lantiq,pull = <2>; + }; + pci-out { + lantiq,groups = "gnt1", "gnt2", "gnt3", "gnt4"; + lantiq,output = <1>; + lantiq,pull = <0>; + }; + ar8030-intr { + lantiq,groups = "exin3"; + lantiq,function = "exin"; + lantiq,pull = <2>; + lantiq,output = <0>; + }; + ar8030-clk { + lantiq,groups = "clkout2"; + lantiq,output = <1>; + lantiq,open-drain; + }; + ar8030-rst { + lantiq,pins = "io34"; + lantiq,output = <1>; + lantiq,pull = <2>; + lantiq,open-drain; + }; + }; +}; + +&gsw { + phy-mode = "rmii"; + phy-handle = <&phy0>; + mtd-mac-address = <&ath9k_cal 0xa91>; + mtd-mac-address-increment = <(-2)>; + + mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + phy0: ethernet-phy@0 { + reg = <0>; + reset-gpios = <&gpio 34 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x1000000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + ath9k_cal: partition@0 { + label = "urlader"; + reg = <0x00000 0x20000>; + read-only; + }; + + partition@20000 { + label = "firmware"; + reg = <0x20000 0xf60000>; + }; + + partition@f80000 { + label = "tffs (1)"; + reg = <0xf80000 0x40000>; + read-only; + }; + + partition@fc0000 { + label = "tffs (2)"; + reg = <0xfc0000 0x40000>; + read-only; + }; + }; + }; +}; + +&pci0 { + status = "okay"; + req-mask = <0xf>; + gpio-reset = <&gpio 21 GPIO_ACTIVE_LOW>; + + wifi@0,0 { + compatible = "pci0,0"; + reg = <0x7000 0 0 0 0>; + qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:00:0e.0.bin */ + }; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/FRITZ7320.dts b/target/linux/lantiq/files/arch/mips/boot/dts/FRITZ7320.dts new file mode 100644 index 0000000000..a4afca11fa --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/FRITZ7320.dts @@ -0,0 +1,172 @@ +/dts-v1/; + +#include "ar9.dtsi" + +#include + +/ { + compatible = "avm,fritz7320", "lantiq,xway", "lantiq,ar9"; + model = "AVM FRITZ!Box 7320"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power; + led-failsafe = &power; + led-running = &power; + led-upgrade = &power; + + led-internet = &info_green; + led-dsl = &power; + led-wifi = &wlan; + }; + + memory@0 { + reg = <0x0 0x4000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + rfkill { + label = "rfkill"; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + dect { + label = "dect"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + power: power { + label = "fritz7320:green:power"; + gpios = <&gpio 44 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + voice { + label = "fritz7320:green:fon"; + gpios = <&gpio 47 GPIO_ACTIVE_LOW>; + }; + dect { + label = "fritz7320:green:dect"; + gpios = <&gpio 38 GPIO_ACTIVE_LOW>; + }; + wlan: wlan { + label = "fritz7320:green:wlan"; + gpios = <&gpio 37 GPIO_ACTIVE_LOW>; + }; + info_green: info_green { + label = "fritz7320:green:info"; + gpios = <&gpio 35 GPIO_ACTIVE_LOW>; + }; + info_red { + label = "fritz7320:red:info"; + gpios = <&gpio 45 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + pci { + lantiq,groups = "gnt1", "req1", "req2", "req3", "req4", "gnt2", "gnt3", "gnt4"; + lantiq,function = "pci"; + }; + pci-in { + lantiq,groups = "req1", "req2", "req3", "req4"; + lantiq,output = <0>; + lantiq,open-drain = <1>; + lantiq,pull = <2>; + }; + pci-out { + lantiq,groups = "gnt1", "gnt2", "gnt3", "gnt4"; + lantiq,output = <1>; + lantiq,pull = <0>; + }; + }; +}; + +&gsw { + phy-mode = "mii"; + mtd-mac-address = <&ath9k_cal 0xa91>; + mtd-mac-address-increment = <(-2)>; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x1000000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + ath9k_cal: partition@0 { + label = "urlader"; + reg = <0x00000 0x20000>; + read-only; + }; + + partition@20000 { + label = "firmware"; + reg = <0x20000 0xf60000>; + }; + + partition@f80000 { + label = "tffs (1)"; + reg = <0xf80000 0x40000>; + read-only; + }; + + partition@fc0000 { + label = "tffs (2)"; + reg = <0xfc0000 0x40000>; + read-only; + }; + }; + }; +}; + +&pci0 { + status = "okay"; + req-mask = <0xf>; + gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; + + wifi@0,0 { + compatible = "pci0,0"; + reg = <0x7000 0 0 0 0>; + qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:00:0e.0.bin */ + }; +}; + +&usb_phy0 { + status = "okay"; +}; + +&usb_phy1 { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; + +&usb1 { + status = "okay"; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/FRITZ7360SL.dts b/target/linux/lantiq/files/arch/mips/boot/dts/FRITZ7360SL.dts new file mode 100644 index 0000000000..599b20a460 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/FRITZ7360SL.dts @@ -0,0 +1,82 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "FRITZ736X.dtsi" + +#include +#include + +/ { + compatible = "avm,fritz7360sl", "avm,fritz736x", "lantiq,xway", "lantiq,vr9"; + model = "AVM FRITZ!Box 7360 SL"; +}; + +&power_green { + label = "fritz7360sl:green:power"; +}; + +&power_red { + label = "fritz7360sl:red:power"; +}; + +&info_green { + label = "fritz7360sl:green:info"; +}; + +&wifi { + label = "fritz7360sl:green:wlan"; +}; + +&info_red { + label = "fritz7360sl:red:info"; +}; + +&dect { + label = "fritz7360sl:green:dect"; +}; + +&state_default { + pcie-rst { + lantiq,pins = "io38"; + lantiq,pull = <0>; + lantiq,output = <1>; + }; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x1000000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + urlader: partition@0 { + label = "urlader"; + reg = <0x00000 0x20000>; + read-only; + }; + + partition@20000 { + label = "firmware"; + reg = <0x20000 0xf60000>; + }; + + partition@f80000 { + label = "tffs (1)"; + reg = <0xf80000 0x40000>; + read-only; + }; + + partition@fc0000 { + label = "tffs (2)"; + reg = <0xfc0000 0x40000>; + read-only; + }; + }; + }; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/FRITZ7362SL.dts b/target/linux/lantiq/files/arch/mips/boot/dts/FRITZ7362SL.dts new file mode 100644 index 0000000000..7a6272b988 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/FRITZ7362SL.dts @@ -0,0 +1,135 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "FRITZ736X.dtsi" + +#include +#include + +/ { + compatible = "avm,fritz7362sl", "avm,fritz736x", "lantiq,xway", "lantiq,vr9"; + model = "AVM FRITZ!Box 7362 SL"; +}; + +&power_green { + label = "fritz7362sl:green:power"; +}; + +&power_red { + label = "fritz7362sl:red:power"; +}; + +&info_green { + label = "fritz7362sl:green:info"; +}; + +&wifi { + label = "fritz7362sl:green:wlan"; +}; + +&info_red { + label = "fritz7362sl:red:info"; +}; + +&dect { + label = "fritz7362sl:green:dect"; +}; + +&gpio { + pins_spi_default: pins_spi_default { + spi_in { + lantiq,groups = "spi_di"; + lantiq,function = "spi"; + }; + + spi_out { + lantiq,groups = "spi_do", "spi_clk", + "spi_cs4"; + lantiq,function = "spi"; + lantiq,output = <1>; + }; + }; +}; + +&state_default { + nand { + lantiq,groups = "nand ale", "nand cle", + "nand cs1", "nand rd", "nand rdy"; + lantiq,function = "ebu"; + }; + + pcie-rst { + lantiq,pins = "io21"; + lantiq,open-drain = <1>; + lantiq,output = <1>; + }; +}; + +&spi { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pins_spi_default>; + + flash@4 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <4 0>; + spi-max-frequency = <1000000>; + + urlader: partition@0 { + reg = <0x0 0x40000>; + label = "urlader"; + read-only; + }; + + partition@40000 { + reg = <0x40000 0x60000>; + label = "tffs (1)"; + read-only; + }; + + partition@A0000 { + reg = <0xA0000 0x60000>; + label = "tffs (2)"; + read-only; + }; + }; +}; + +&localbus { + nand@1 { + compatible = "lantiq,nand-xway"; + lantiq,cs1 = <1>; + bank-width = <1>; + reg = <1 0x0 0x2000000>; + #address-cells = <1>; + #size-cells = <1>; + nand-ecc-mode = "on-die"; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "kernel"; + reg = <0x0 0x400000>; + }; + + partition@400000 { + label = "ubi"; + reg = <0x400000 0x7c00000>; + }; + }; + }; +}; + +&pcie0 { + gpio-reset = <&gpio 21 GPIO_ACTIVE_LOW>; + + pcie@0 { + #size-cells = <1>; + #address-cells = <2>; + }; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/FRITZ736X.dtsi b/target/linux/lantiq/files/arch/mips/boot/dts/FRITZ736X.dtsi new file mode 100644 index 0000000000..9c1d2db8fa --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/FRITZ736X.dtsi @@ -0,0 +1,205 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "vr9.dtsi" + +#include +#include + +/ { + compatible = "avm,fritz736x", "lantiq,xway", "lantiq,vr9"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power_green; + led-failsafe = &power_red; + led-running = &power_green; + led-upgrade = &power_green; + led-dsl = &info_green; + led-wifi = &wifi; + }; + + memory@0 { + reg = <0x0 0x8000000>; + }; + + keys { + compatible = "gpio-keys-polled"; + poll-interval = <100>; + + dect { + label = "dect"; + gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; + linux,code = ; + }; + + wifi { + label = "wifi"; + gpios = <&gpio 29 GPIO_ACTIVE_HIGH>; + linux,code = ; + }; + }; + + leds: leds { + compatible = "gpio-leds"; + + power_green: power { + gpios = <&gpio 32 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + + power_red: power2 { + gpios = <&gpio 33 GPIO_ACTIVE_LOW>; + }; + + info_green: info_green { + gpios = <&gpio 47 GPIO_ACTIVE_LOW>; + }; + + wifi: wifi { + gpios = <&gpio 36 GPIO_ACTIVE_LOW>; + }; + + info_red: info_red { + gpios = <&gpio 34 GPIO_ACTIVE_LOW>; + }; + + dect: dect { + gpios = <&gpio 35 GPIO_ACTIVE_LOW>; + }; + }; +}; + +ð0 { + lan: interface@0 { + compatible = "lantiq,xrx200-pdi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + mtd-mac-address = <&urlader 0xa91>; + mtd-mac-address-increment = <(-2)>; + lantiq,switch; + + ethernet@0 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <0>; + phy-mode = "rmii"; + phy-handle = <&phy0>; + }; + + ethernet@1 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <1>; + phy-mode = "rmii"; + phy-handle = <&phy1>; + }; + + ethernet@2 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <2>; + phy-mode = "gmii"; + phy-handle = <&phy11>; + }; + + ethernet@3 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <4>; + phy-mode = "gmii"; + phy-handle = <&phy13>; + }; + }; + + mdio@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-mdio"; + reg = <0>; + + phy0: ethernet-phy@0 { + reg = <0x00>; + compatible = "ethernet-phy-ieee802.3-c22"; + reset-gpios = <&gpio 37 GPIO_ACTIVE_LOW>; + }; + + phy1: ethernet-phy@1 { + reg = <0x01>; + compatible = "ethernet-phy-ieee802.3-c22"; + reset-gpios = <&gpio 44 GPIO_ACTIVE_LOW>; + }; + + phy11: ethernet-phy@11 { + reg = <0x11>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + + phy13: ethernet-phy@13 { + reg = <0x13>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + }; +}; + +&gphy0 { + lantiq,gphy-mode = ; +}; + +&gphy1 { + lantiq,gphy-mode = ; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + mdio { + lantiq,groups = "mdio"; + lantiq,function = "mdio"; + }; + + phy-rst { + lantiq,pins = "io37", "io44"; + lantiq,pull = <0>; + lantiq,open-drain; + lantiq,output = <1>; + }; + }; + +}; + +&pcie0 { + status = "okay"; + + pcie@0 { + reg = <0 0 0 0 0>; + #interrupt-cells = <1>; + #size-cells = <1>; + #address-cells = <2>; + device_type = "pci"; + + wifi@168c,002e { + compatible = "pci168c,002e"; + reg = <0 0 0 0 0>; + qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:01:00.0.bin */ + }; + }; +}; + +&usb_phy0 { + status = "okay"; +}; + +&usb_phy1 { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; + +&usb1 { + status = "okay"; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/FRITZ7412.dts b/target/linux/lantiq/files/arch/mips/boot/dts/FRITZ7412.dts new file mode 100644 index 0000000000..3059c12858 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/FRITZ7412.dts @@ -0,0 +1,230 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "vr9.dtsi" + +#include +#include + +/ { + compatible = "avm,fritz7412", "lantiq,xway", "lantiq,vr9"; + model = "AVM FRITZ!Box 7412"; + + chosen { + bootargs = "console=ttyLTQ0,115200 mem=126M vpe1_load_addr=0x87e00000 vpe1_mem=2M maxvpes=1 maxtcs=1 nosmp"; + }; + + aliases { + led-boot = &power_green; + led-failsafe = &power_red; + led-running = &power_green; + + led-dsl = &info; + led-wifi = &wifi; + }; + + memory@0 { + reg = <0x0 0x8000000>; + }; + + keys { + compatible = "gpio-keys-polled"; + poll-interval = <100>; + + wps { + label = "wps"; + gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; + linux,code = ; + }; + + dect { + label = "dect"; + gpios = <&gpio 2 GPIO_ACTIVE_HIGH>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + power_green: power_green { + label = "fritz7412:green:power"; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + + power_red: power_red { + label = "fritz7412:red:power"; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + }; + + fon { + label = "fritz7412:green:fon"; + gpios = <&gpio 34 GPIO_ACTIVE_LOW>; + }; + + dect { + label = "fritz7412:green:dect"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + }; + + wifi: wifi { + label = "fritz7412:green:wifi"; + gpios = <&gpio 0 GPIO_ACTIVE_LOW>; + }; + + info: info { + label = "fritz7412:green:info"; + gpios = <&gpio 35 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&localbus { + nand@0 { + compatible = "lantiq,nand-xway"; + bank-width = <2>; + reg = <0 0x0 0x2000000>; + #address-cells = <1>; + #size-cells = <1>; + lantiq,cs = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "urlader"; + reg = <0x0 0x40000>; + read-only; + }; + + partition@40000 { + label = "nand-tffs"; + reg = <0x40000 0x400000>; + read-only; + }; + + partition@440000 { + label = "kernel"; + reg = <0x440000 0x400000>; + }; + + partition@840000 { + label = "ubi"; + reg = <0x840000 0x3000000>; + }; + + partition@3840000 { + label = "reserved-kernel"; + reg = <0x3840000 0x400000>; + read-only; + }; + + partition@3c40000 { + label = "reserved-filesystem"; + reg = <0x3c40000 0x3000000>; + read-only; + }; + + partition@6c40000 { + label = "config"; + reg = <0x6c40000 0x400000>; + read-only; + }; + + partition@6e40000 { + label = "nand-filesystem"; + reg = <0x6e40000 0x400000>; + read-only; + }; + }; + }; +}; + +&pcie0 { + status = "okay"; + gpio-reset = <&gpio 11 GPIO_ACTIVE_HIGH>; + + pcie@0 { + reg = <0 0 0 0 0>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + device_type = "pci"; + + wifi@168c,002e { + compatible = "pci168c,002e"; + reg = <0 0 0 0 0>; + qca,no-eeprom; /* load from ath9k-eeprom-pci-0000:01:00.0.bin */ + }; + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + mdio { + lantiq,groups = "mdio"; + lantiq,function = "mdio"; + }; + pcie-rst { + lantiq,pins = "io11"; + lantiq,open-drain = <1>; + lantiq,output = <1>; + }; + nand-mux { + lantiq,groups = "nand cle", "nand ale", + "nand rd", "nand cs1", + "nand rdy"; + lantiq,function = "ebu"; + }; + nand-pins { + lantiq,pins = "io13", "io24", "io49"; + lantiq,pull = <1>; + }; + }; +}; + +&gphy0 { + lantiq,gphy-mode = ; +}; + +ð0 { + lantiq,phys = <&gphy0>; + + interface@0 { + compatible = "lantiq,xrx200-pdi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + mac-address = [ 00 11 22 33 44 55 ]; + lantiq,switch; + + ethernet@2 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <2>; + phy-mode = "gmii"; + phy-handle = <&phy11>; + }; + }; + + mdio@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + compatible = "lantiq,xrx200-mdio"; + + phy11: ethernet-phy@11 { + reg = <0x11>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + }; +}; + +&vmmc { + status = "okay"; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/GIGASX76X.dts b/target/linux/lantiq/files/arch/mips/boot/dts/GIGASX76X.dts new file mode 100644 index 0000000000..36b82515dc --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/GIGASX76X.dts @@ -0,0 +1,130 @@ +/dts-v1/; + +#include "danube.dtsi" + +#include + +/ { + compatible = "siemens,gigaset-sx76x", "lantiq,xway", "lantiq,danube"; + model = "Gigaset SX761,SX762,SX763"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + memory@0 { + reg = <0x0 0x2000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + reset { + label = "reset"; + gpios = <&gpio 14 GPIO_ACTIVE_HIGH>; + linux,code = ; + }; + }; + + gpio_export { + compatible = "gpio-export"; + #size-cells = <0>; + + switch { + gpio-export,name = "switch"; + gpio-export,output = <1>; + gpios = <&gpio 19 GPIO_ACTIVE_HIGH>; + }; + }; + + usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio 29 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + stp { + lantiq,groups = "stp"; + lantiq,function = "stp"; + }; + }; +}; + + +&gpiomm { + status = "okay"; + lantiq,shadow = <0x3>; +}; + +&gpios { + status = "okay"; +}; + +&gsw { + phy-mode = "rmii"; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x2000000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x0 0x30000>; + }; + + partition@10000 { + label = "uboot_env"; + reg = <0x30000 0x10000>; + }; + + partition@40000 { + label = "firmware"; + reg = <0x40000 0x7c0000>; + }; + }; + }; +}; + +&pci0 { + status = "okay"; + gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; +}; + +&usb_phy { + status = "okay"; +}; + +&usb { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; + +&vmmc { + status = "okay"; + gpios = <&gpiomm 1 GPIO_ACTIVE_HIGH>; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/H201L.dts b/target/linux/lantiq/files/arch/mips/boot/dts/H201L.dts new file mode 100644 index 0000000000..46cae21a58 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/H201L.dts @@ -0,0 +1,175 @@ +/dts-v1/; + +#include "ar9.dtsi" + +#include + +/ { + compatible = "zte,h201l", "lantiq,xway", "lantiq,ar9"; + model = "ZTE H210L"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power_green; + led-failsafe = &power_green; + led-running = &power_green; + led-upgrade = &power_green; + + led-dsl = &dsl; + led-internet = &online; + led-usb = &led_usb; + led-wifi = &wifi; + }; + + memory@0 { + reg = <0x0 0x2000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + reset { + label = "reset"; + gpios = <&gpio 53 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + wps { + label = "wps"; + gpios = <&gpio 54 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + rfkill { + label = "rfkill"; + gpios = <&gpio 55 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + power_green: power { + label = "h201l:green:power"; + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + online: online { + label = "h201l:green:internet"; + gpios = <&gpio 37 GPIO_ACTIVE_LOW>; + }; + dsl: dsl { + label = "h201l:green:dsl"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + phone { + label = "h201l:green:phone"; + gpios = <&gpio 39 GPIO_ACTIVE_LOW>; + }; + wps { + label = "h201l:green:wps"; + gpios = <&gpio 22 GPIO_ACTIVE_LOW>; + }; + wifi: wifi { + label = "h201l:green:wlan"; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + }; + led_usb: usb { + label = "h201l:green:usb"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + }; + }; + + gpio_export { + compatible = "gpio-export"; + #size-cells = <0>; + + switch { + gpio-export,name = "switch"; + gpio-export,output = <1>; + gpios = <&gpio 38 GPIO_ACTIVE_HIGH>; + }; + usb { + gpio-export,name = "usb"; + gpio-export,output = <1>; + gpios = <&gpio 28 GPIO_ACTIVE_HIGH>; + }; + wifi { + gpio-export,name = "wifi"; + gpio-export,output = <1>; + gpios = <&gpio 7 GPIO_ACTIVE_HIGH>; + }; + }; + + usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio 36 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + }; +}; + +&gsw { + phy-mode = "rgmii"; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x2000000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x00000 0x20000>; + read-only; + }; + + partition@20000 { + label = "uboot_env"; + reg = <0x20000 0x10000>; + read-only; + }; + + partition@30000 { + label = "firmware"; + reg = <0x30000 0x7d0000>; + }; + }; + }; +}; + +&usb_phy0 { + status = "okay"; +}; + + +&usb0 { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/P2601HNFX.dts b/target/linux/lantiq/files/arch/mips/boot/dts/P2601HNFX.dts new file mode 100644 index 0000000000..5606eb6e8b --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/P2601HNFX.dts @@ -0,0 +1,196 @@ +/dts-v1/; + +#include "ar9.dtsi" + +#include + +/ { + compatible = "zyxel,p-2601hn", "lantiq,xway", "lantiq,ar9"; + model = "ZyXEL P-2601HN-Fx"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power_green; + led-failsafe = &power_red; + led-running = &power_green; + led-upgrade = &power_green; + + led-dsl = &dsl; + led-internet = &online; + led-wifi = &wifi; + }; + + memory@0 { + reg = <0x0 0x4000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + reset { + label = "reset"; + gpios = <&gpio 53 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + rfkill { + label = "rfkill"; + gpios = <&gpio 54 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + power_green: power { + label = "p2601hnfx:green:power"; + gpios = <&stp 11 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + power_red: power2 { + label = "p2601hnfx:red:power"; + gpios = <&gpio 29 GPIO_ACTIVE_LOW>; + }; + online: online { + label = "p2601hnfx:green:internet"; + gpios = <&stp 13 GPIO_ACTIVE_LOW>; + }; + online2 { + label = "p2601hnfx:red:internet"; + gpios = <&stp 12 GPIO_ACTIVE_LOW>; + }; + dsl: dsl { + label = "p2601hnfx:green:dsl"; + gpios = <&stp 14 GPIO_ACTIVE_LOW>; + }; + phone { + label = "p2601hnfx:green:phone"; + gpios = <&stp 9 GPIO_ACTIVE_LOW>; + }; + phone2 { + label = "p2601hnfx:orange:phone"; + gpios = <&stp 8 GPIO_ACTIVE_LOW>; + }; + wifi: wifi { + label = "p2601hnfx:green:wireless"; + gpios = <&stp 15 GPIO_ACTIVE_LOW>; + }; + wifi2 { + label = "p2601hnfx:orange:wireless"; + gpios = <&stp 10 GPIO_ACTIVE_LOW>; + }; + }; + + gpio_export { + compatible = "gpio-export"; + #size-cells = <0>; + + switch { + gpio-export,name = "switch"; + gpio-export,output = <1>; + gpios = <&gpio 50 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + stp { + lantiq,groups = "stp"; + lantiq,function = "stp"; + lantiq,pull = <2>; + lantiq,open-drain = <0>; + lantiq,output = <1>; + }; + exin { + lantiq,groups = "exin1"; + lantiq,function = "exin"; + }; + pci { + lantiq,groups = "gnt1"; + lantiq,function = "pci"; + }; + conf_out { + lantiq,pins = "io4", "io5", "io6"; + lantiq,open-drain; + lantiq,pull = <0>; + }; + mdio { + lantiq,groups = "mdio"; + lantiq,function = "mdio"; + }; + }; + + usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio 9 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&gsw { + phy-mode = "rmii"; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x2000000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x00000 0x40000>; + read-only; + }; + + partition@40000 { + label = "uboot_env"; + reg = <0x40000 0x20000>; + read-only; + }; + + partition@60000 { + label = "firmware"; + reg = <0x60000 0xfa0000>; + }; + }; + }; +}; + +&stp { + status = "okay"; + lantiq,shadow = <0xfff>; + lantiq,groups = <0x3>; +}; + +&usb_phy0 { + status = "okay"; +}; + +&usb0 { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/P2812HNUF1.dts b/target/linux/lantiq/files/arch/mips/boot/dts/P2812HNUF1.dts new file mode 100644 index 0000000000..d907d64c8c --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/P2812HNUF1.dts @@ -0,0 +1,70 @@ +/dts-v1/; + +#include "P2812HNUFX.dtsi" + +/ { + compatible = "zyxel,p-2812hnu-f1", "zyxel,p-2812hnu", "lantiq,xway", "lantiq,vr9"; + model = "ZyXEL P-2812HNU-F1"; + + aliases { + led-usb = &led_usb1; + led-usb2 = &led_usb2; + }; + + gpio-leds { + led_usb1: usb1 { + label = "p2812hnuf1:green:usb1"; + gpios = <&gpio 38 GPIO_ACTIVE_LOW>; + }; + led_usb2: usb2 { + label = "p2812hnuf1:green:usb2"; + gpios = <&gpio 44 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&localbus { + nand@0 { + compatible = "lantiq,nand-xway"; + lantiq,cs = <1>; + bank-width = <2>; + reg = <0 0x0 0x2000000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x00000 0x40000>; + }; + partition@40000 { + label = "uboot-env"; + reg = <0x40000 0x20000>; + }; + partition@60000 { + label = "kernel"; + reg = <0x60000 0x300000>; + }; + partition@360000 { + label = "ubi"; + reg = <0x360000 0x7ca0000>; + }; + }; + }; +}; + +&pci0 { + wifi@1814,3062 { + compatible = "pci1814,3062"; + reg = <0x7000 0 0 0 0>; + ralink,eeprom = "RT3062.eeprom"; + }; +}; + +&pcie0 { + status = "disabled"; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/P2812HNUF3.dts b/target/linux/lantiq/files/arch/mips/boot/dts/P2812HNUF3.dts new file mode 100644 index 0000000000..202226aa86 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/P2812HNUF3.dts @@ -0,0 +1,64 @@ +/dts-v1/; + +#include "P2812HNUFX.dtsi" + +/ { + compatible = "zyxel,p-2812hnu-f3", "zyxel,p-2812hnu", "lantiq,xway", "lantiq,vr9"; + model = "ZyXEL P-2812HNU-F3"; +}; + +&pci0 { + wifi@1814,3092 { + compatible = "pci1814,3092"; + reg = <0x7000 0 0 0 0>; + ralink,eeprom = "RT3092.eeprom"; + }; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x800000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x0 0x50000>; + read-only; + }; + partition@50000 { + label = "uboot-env"; + reg = <0x50000 0x10000>; + }; + partition@60000 { + label = "unused"; + reg = <0x60000 0x7a0000>; + }; + }; + }; + + nand@1 { + compatible = "lantiq,nand-xway"; + lantiq,cs = <1>; + bank-width = <2>; + reg = <1 0x0 0x2000000>; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "kernel"; + reg = <0x0 0x200000>; + }; + partition@200000 { + label = "ubi"; + reg = <0x200000 0x7e00000>; + }; + }; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/P2812HNUFX.dtsi b/target/linux/lantiq/files/arch/mips/boot/dts/P2812HNUFX.dtsi new file mode 100644 index 0000000000..65424e3eff --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/P2812HNUFX.dtsi @@ -0,0 +1,298 @@ +#include "vr9.dtsi" + +#include +#include + +/ { + compatible = "zyxel,p-2812hnu", "lantiq,xway", "lantiq,vr9"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power_green; + led-failsafe = &power_red; + led-running = &power_green; + led-upgrade = &power_green; + + led-dsl = &dsl_green; + led-internet = &internet_green; + led-wifi = &wireless_green; + }; + + memory@0 { + reg = <0x0 0x8000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + reset { + label = "reset"; + gpios = <&gpio 39 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + rfkill { + label = "rfkill"; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + internet_red { + label = "p2812hnufx:red:internet"; + gpios = <&stp 16 GPIO_ACTIVE_LOW>; + }; + internet_green: internet_green { + label = "p2812hnufx:green:internet"; + gpios = <&stp 17 GPIO_ACTIVE_LOW>; + }; + dsl_green: dsl_green { + label = "p2812hnufx:green:dsl"; + gpios = <&stp 18 GPIO_ACTIVE_LOW>; + }; + dsl_orange { + label = "p2812hnufx:orange:dsl"; + gpios = <&stp 19 GPIO_ACTIVE_LOW>; + }; + wireless_orange { + label = "p2812hnufx:orange:wlan"; + gpios = <&stp 20 GPIO_ACTIVE_LOW>; + }; + wireless_green: wireless_green { + label = "p2812hnufx:green:wlan"; + gpios = <&stp 21 GPIO_ACTIVE_LOW>; + }; + power_red: power { + label = "p2812hnufx:red:power"; + gpios = <&stp 22 GPIO_ACTIVE_LOW>; + }; + power_green: power2 { + label = "p2812hnufx:green:power"; + gpios = <&stp 23 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + phone1 { + label = "p2812hnufx:green:phone"; + gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + }; + phone1warn { + label = "p2812hnufx:orange:phone"; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + }; + phone2warn { + label = "p2812hnufx:orange:phone2"; + gpios = <&gpio 26 GPIO_ACTIVE_LOW>; + }; + phone2 { + label = "p2812hnufx:green:phone2"; + gpios = <&gpio 28 GPIO_ACTIVE_LOW>; + }; + }; + + usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio 33 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +ð0 { + lan: interface@0 { + compatible = "lantiq,xrx200-pdi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + mac-address = [ 00 11 22 33 44 55 ]; + lantiq,switch; + + ethernet@0 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <0>; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + }; + ethernet@1 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <1>; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + }; + ethernet@2 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <2>; + phy-mode = "gmii"; + phy-handle = <&phy11>; + }; + ethernet@4 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <4>; + phy-mode = "gmii"; + phy-handle = <&phy13>; + }; + ethernet@5 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <5>; + phy-mode = "rgmii"; + phy-handle = <&phy5>; + }; + }; + + mdio@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-mdio"; + reg = <0>; + + phy0: ethernet-phy@0 { + reg = <0x0>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + phy1: ethernet-phy@1 { + reg = <0x1>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + phy5: ethernet-phy@5 { + reg = <0x5>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + phy11: ethernet-phy@11 { + reg = <0x11>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + phy13: ethernet-phy@13 { + reg = <0x13>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + }; +}; + +&gphy0 { + lantiq,gphy-mode = ; +}; + +&gphy1 { + lantiq,gphy-mode = ; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + exin3 { + lantiq,groups = "exin3"; + lantiq,function = "exin"; + }; + mdio { + lantiq,groups = "mdio"; + lantiq,function = "mdio"; + }; + gphy-leds { + lantiq,groups = "gphy0 led1", "gphy1 led1", + "gphy0 led2", "gphy1 led2"; + lantiq,function = "gphy"; + lantiq,pull = <2>; + lantiq,open-drain = <0>; + lantiq,output = <1>; + }; + stp { + lantiq,groups = "stp"; + lantiq,function = "stp"; + lantiq,pull = <2>; + lantiq,open-drain = <0>; + lantiq,output = <1>; + }; + pci-in { + lantiq,groups = "req1"; + lantiq,function = "pci"; + lantiq,output = <0>; + lantiq,open-drain = <1>; + lantiq,pull = <2>; + }; + pci-out { + lantiq,groups = "gnt1"; + lantiq,function = "pci"; + lantiq,output = <1>; + lantiq,open-drain = <0>; + lantiq,pull = <0>; + }; + pci_rst { + lantiq,pins = "io21"; + lantiq,output = <1>; + lantiq,open-drain = <0>; + lantiq,pull = <2>; + }; + pcie-rst { + lantiq,pins = "io38"; + lantiq,pull = <0>; + lantiq,output = <1>; + }; + ifxhcd-rst { + lantiq,pins = "io33"; + lantiq,pull = <0>; + lantiq,open-drain = <0>; + lantiq,output = <1>; + }; + nand_out { + lantiq,groups = "nand cle", "nand ale"; + lantiq,function = "ebu"; + lantiq,output = <1>; + lantiq,open-drain = <0>; + lantiq,pull = <0>; + }; + nand_cs1 { + lantiq,groups = "nand cs1"; + lantiq,function = "ebu"; + lantiq,open-drain = <0>; + lantiq,pull = <0>; + }; + }; +}; + +&pci0 { + status = "okay"; + gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; +}; + +&stp { + status = "okay"; + + lantiq,shadow = <0xffffff>; + lantiq,groups = <0x7>; + lantiq,dsl = <0x0>; + lantiq,phy1 = <0x0>; + lantiq,phy2 = <0x0>; +}; + +&usb_phy0 { + status = "okay"; +}; + +&usb_phy1 { + status = "okay"; +}; + +&usb0 { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; + +&usb1 { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/TDW8970.dts b/target/linux/lantiq/files/arch/mips/boot/dts/TDW8970.dts new file mode 100644 index 0000000000..25eb3dac67 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/TDW8970.dts @@ -0,0 +1,8 @@ +/dts-v1/; + +#include "TDW89X0.dtsi" + +/ { + compatible = "tplink,tdw8970", "tplink,tdw89x0", "lantiq,xway", "lantiq,vr9"; + model = "TP-LINK TD-W8970"; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/TDW8980.dts b/target/linux/lantiq/files/arch/mips/boot/dts/TDW8980.dts new file mode 100644 index 0000000000..76875e735d --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/TDW8980.dts @@ -0,0 +1,33 @@ +/dts-v1/; + +#include "TDW89X0.dtsi" + +/ { + compatible = "tplink,tdw8980", "tplink,tdw89x0", "lantiq,xway", "lantiq,vr9"; + model = "TP-LINK TD-W8980"; + + gpio-leds { + wifi2 { + label = "tdw8980:green:wlan5ghz"; + gpios = <&gpio 24 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&gpio { + state_default: pinmux { + pci_rst { + lantiq,pins = "io21"; + lantiq,output = <1>; + lantiq,open-drain; + }; + }; +}; + +&pci0 { + status = "okay"; + lantiq,bus-clock = <33333333>; + interrupt-map-mask = <0xf800 0x0 0x0 0x7>; + interrupt-map = <0x7000 0 0 1 &icu0 30 1>; + gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/TDW89X0.dtsi b/target/linux/lantiq/files/arch/mips/boot/dts/TDW89X0.dtsi new file mode 100644 index 0000000000..71e051a316 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/TDW89X0.dtsi @@ -0,0 +1,299 @@ +#include "vr9.dtsi" + +#include +#include + +/ { + compatible = "tplink,tdw89x0", "lantiq,xway", "lantiq,vr9"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + /* the power led can't be controlled, use the wps led instead */ + led-boot = &wps; + led-failsafe = &wps; + + led-dsl = &dsl; + led-internet = &internet; + led-wifi = &wifi; + led-usb = &led_usb0; + led-usb2 = &led_usb2; + }; + + memory@0 { + reg = <0x0 0x4000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + reset { + label = "reset"; + gpios = <&gpio 0 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wifi { + label = "wifi"; + gpios = <&gpio 9 GPIO_ACTIVE_HIGH>; + linux,code = ; + linux,input-type = ; + }; + + wps { + label = "wps"; + gpios = <&gpio 39 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + /* + power is not controllable via gpio + */ + dsl: dsl { + label = "tdw89x0:green:dsl"; + gpios = <&gpio 4 GPIO_ACTIVE_HIGH>; + }; + internet: internet { + label = "tdw89x0:green:internet"; + gpios = <&gpio 5 GPIO_ACTIVE_HIGH>; + }; + + led_usb0: usb0 { + label = "tdw89x0:green:usb"; + gpios = <&gpio 19 GPIO_ACTIVE_HIGH>; + }; + led_usb2: usb2 { + label = "tdw89x0:green:usb2"; + gpios = <&gpio 20 GPIO_ACTIVE_HIGH>; + }; + wps: wps { + label = "tdw89x0:green:wps"; + gpios = <&gpio 37 GPIO_ACTIVE_HIGH>; + }; + }; + + wifi-leds { + compatible = "gpio-leds"; + + wifi: wifi { + label = "tdw89x0:green:wifi"; + gpios = <&ath9k 0 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy0tpt"; + }; + }; + + + usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio 33 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +ð0 { + lan: interface@0 { + compatible = "lantiq,xrx200-pdi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + mtd-mac-address = <&ath9k_cal 0xf100>; + lantiq,switch; + + ethernet@0 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <0>; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + // gpios = <&gpio 42 GPIO_ACTIVE_LOW>; + }; + ethernet@5 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <5>; + phy-mode = "rgmii"; + phy-handle = <&phy5>; + }; + ethernet@2 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <2>; + phy-mode = "gmii"; + phy-handle = <&phy11>; + }; + ethernet@3 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <4>; + phy-mode = "gmii"; + phy-handle = <&phy13>; + }; + }; + + mdio@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-mdio"; + reg = <0>; + + phy0: ethernet-phy@0 { + reg = <0x0>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + phy5: ethernet-phy@5 { + reg = <0x5>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + phy11: ethernet-phy@11 { + reg = <0x11>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + phy13: ethernet-phy@13 { + reg = <0x13>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + }; +}; + +&gphy0 { + lantiq,gphy-mode = ; +}; + +&gphy1 { + lantiq,gphy-mode = ; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + mdio { + lantiq,groups = "mdio"; + lantiq,function = "mdio"; + }; + gphy-leds { + lantiq,groups = "gphy0 led1", "gphy1 led1"; + lantiq,function = "gphy"; + lantiq,pull = <2>; + lantiq,open-drain = <0>; + lantiq,output = <1>; + }; + phy-rst { + lantiq,pins = "io42"; + lantiq,pull = <0>; + lantiq,open-drain = <0>; + lantiq,output = <1>; + }; + pcie-rst { + lantiq,pins = "io38"; + lantiq,pull = <0>; + lantiq,output = <1>; + }; + }; + pins_spi_default: pins_spi_default { + spi_in { + lantiq,groups = "spi_di"; + lantiq,function = "spi"; + }; + spi_out { + lantiq,groups = "spi_do", "spi_clk", + "spi_cs4"; + lantiq,function = "spi"; + lantiq,output = <1>; + }; + }; +}; + +&pcie0 { + pcie@0 { + reg = <0 0 0 0 0>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + device_type = "pci"; + + ath9k: wifi@168c,002e { + compatible = "pci168c,002e"; + reg = <0 0 0 0 0>; + #gpio-cells = <2>; + gpio-controller; + qca,no-eeprom; + qca,disable-5ghz; + mtd-mac-address = <&ath9k_cal 0xf100>; + mtd-mac-address-increment = <2>; + }; + }; +}; + +&spi { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pins_spi_default>; + + m25p80@4 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <4 0>; + spi-max-frequency = <33250000>; + m25p,fast-read; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + reg = <0x0 0x20000>; + label = "u-boot"; + read-only; + }; + + partition@20000 { + reg = <0x20000 0x7a0000>; + label = "firmware"; + }; + + partition@7c0000 { + reg = <0x7c0000 0x10000>; + label = "config"; + read-only; + }; + + ath9k_cal: partition@7d0000 { + reg = <0x7d0000 0x30000>; + label = "boardconfig"; + read-only; + }; + }; + }; +}; + +&usb_phy0 { + status = "okay"; +}; + +&usb_phy1 { + status = "okay"; +}; + +&usb0 { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; + +&usb1 { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/VG3503J.dts b/target/linux/lantiq/files/arch/mips/boot/dts/VG3503J.dts new file mode 100644 index 0000000000..9735b2e011 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/VG3503J.dts @@ -0,0 +1,165 @@ +/dts-v1/; + +#include "vr9.dtsi" + +#include +#include + +/ { + compatible = "arcadyan,vg3503j", "lantiq,xway", "lantiq,vr9"; + model = "BT OpenReach VDSL Modem"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power_green; + led-failsafe = &power_red; + led-running = &power_green; + led-upgrade = &power_green; + + led-dsl = &dsl; + }; + + memory@0 { + reg = <0x0 0x2000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + reset { + label = "reset"; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + power_red: power2 { + label = "vg3503j:red:power"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + }; + dsl: dsl { + label = "vg3503j:green:dsl"; + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; + }; + power_green: power { + label = "vg3503j:green:power"; + gpios = <&gpio 28 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + }; +}; + +ð0 { + interface@0 { + compatible = "lantiq,xrx200-pdi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + lantiq,switch; + ethernet@2 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <2>; + phy-mode = "mii"; + phy-handle = <&phy11>; + }; + ethernet@4 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <4>; + phy-mode = "mii"; + phy-handle = <&phy13>; + }; + }; + + mdio@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-mdio"; + reg = <0>; + + phy11: ethernet-phy@11 { + reg = <0x11>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + lantiq,led1h = <0x70>; + lantiq,led1l = <0x00>; + lantiq,led2h = <0x00>; + lantiq,led2l = <0x03>; + }; + phy13: ethernet-phy@13 { + reg = <0x13>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + lantiq,led1h = <0x70>; + lantiq,led1l = <0x00>; + lantiq,led2h = <0x00>; + lantiq,led2l = <0x03>; + }; + }; +}; + +&gphy0 { + lantiq,gphy-mode = ; +}; + +&gphy1 { + lantiq,gphy-mode = ; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + mdio { + lantiq,groups = "mdio"; + lantiq,function = "mdio"; + }; + gphy-leds { + lantiq,groups = "gphy0 led0", "gphy0 led1", + "gphy0 led2", "gphy1 led0", + "gphy1 led1", "gphy1 led2"; + lantiq,function = "gphy"; + lantiq,pull = <2>; + lantiq,open-drain = <0>; + lantiq,output = <1>; + }; + }; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x2000000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x00000 0x20000>; + }; + + partition@20000 { + label = "firmware"; + reg = <0x20000 0x7d0000>; + }; + + partition@7f0000 { + label = "uboot-env"; + reg = <0x7f0000 0x10000>; + }; + }; + }; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/VGV7510KW22.dtsi b/target/linux/lantiq/files/arch/mips/boot/dts/VGV7510KW22.dtsi new file mode 100644 index 0000000000..811f39d08b --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/VGV7510KW22.dtsi @@ -0,0 +1,269 @@ +#include "vr9.dtsi" + +#include +#include + +/ { + compatible = "arcadyan,vgv7510kw22", "lantiq,xway", "lantiq,vr9"; + + chosen { + bootargs = "console=ttyLTQ0,115200 mem=62M vpe1_load_addr=0x83e00000 vpe1_mem=2M maxvpes=1 maxtcs=1 nosmp"; + }; + + aliases { + led-boot = &power_green; + led-failsafe = &power_red; + led-running = &power_green; + led-upgrade = &power_green; + + led-dsl = &dsl; + led-internet = &internet_green; + led-wifi = &wifi; + }; + + memory@0 { + reg = <0x0 0x4000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + reset { + label = "reset"; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&gpio 9 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + dsl: dsl { + label = "vgv7510kw22:green:dsl"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + }; + + internet_red { + label = "vgv7510kw22:red:internet"; + gpios = <&gpio 10 GPIO_ACTIVE_LOW>; + }; + + info_red { + label = "vgv7510kw22:red:info"; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + }; + + power_green: power { + label = "vgv7510kw22:green:power"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + + info_green { + label = "vgv7510kw22:green:info"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + }; + + internet_green: internet_green { + label = "vgv7510kw22:green:internet"; + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; + }; + + wifi: wifi { + label = "vgv7510kw22:green:wlan"; + gpios = <&gpio 20 GPIO_ACTIVE_LOW>; + }; + + power_red: power2 { + label = "vgv7510kw22:red:power"; + gpios = <&gpio 28 GPIO_ACTIVE_LOW>; + }; + + phone { + label = "vgv7510kw22:green:telefon"; + gpios = <&gpio 29 GPIO_ACTIVE_LOW>; + }; + }; + + usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio 47 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +ð0 { + lan: interface@0 { + compatible = "lantiq,xrx200-pdi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + mtd-mac-address = <&boardconfig 0x16>; + lantiq,switch; + + ethernet@0 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <0>; + phy-mode = "mii"; + phy-handle = <&phy1>; + }; + ethernet@2 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <2>; + phy-mode = "mii"; + phy-handle = <&phy11>; + }; + ethernet@3 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <3>; + phy-mode = "mii"; + phy-handle = <&phy12>; + }; + ethernet@4 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <4>; + phy-mode = "mii"; + phy-handle = <&phy13>; + }; + ethernet@5 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <5>; + phy-mode = "mii"; + phy-handle = <&phy14>; + }; + }; + + mdio@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-mdio"; + reg = <0>; + + phy1: ethernet-phy@1 { + reg = <0x1>; + compatible = "ethernet-phy-ieee802.3-c22"; + }; + + phy11: ethernet-phy@11 { + reg = <0x11>; + compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; + }; + phy12: ethernet-phy@12 { + reg = <0x12>; + compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; + }; + phy13: ethernet-phy@13 { + reg = <0x13>; + compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; + }; + phy14: ethernet-phy@14 { + reg = <0x14>; + compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; + }; + }; +}; + +&gphy0 { + lantiq,gphy-mode = ; +}; + +&gphy1 { + lantiq,gphy-mode = ; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + gphy-leds { + lantiq,groups = "gphy0 led0", "gphy0 led1", + "gphy1 led0", "gphy1 led1"; + lantiq,function = "gphy"; + lantiq,open-drain = <0>; + lantiq,pull = <2>; + lantiq,output = <1>; + }; + mdio { + lantiq,groups = "mdio"; + lantiq,function = "mdio"; + }; + pci-rst { + lantiq,pins = "io21"; + lantiq,open-drain = <0>; + lantiq,pull = <0>; + lantiq,output = <1>; + }; + }; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x1000000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + boardconfig: partition@fe0000 { + label = "board_config"; + reg = <0xfe0000 0x20000>; + read-only; + }; + }; + }; +}; + +&pci0 { + status = "okay"; + gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; + + wifi@1814,3592 { + compatible = "pci1814,3592"; + reg = <0x7000 0 0 0 0>; + ralink,mtd-eeprom = <&boardconfig 0x410>; + ralink,mtd-eeprom-swap; + mtd-mac-address = <&boardconfig 0x16>; + mtd-mac-address-increment = <1>; + }; +}; + +&pcie0 { + status = "disabled"; +}; + +&usb_phy0 { + status = "okay"; +}; + +&usb0 { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; + +&vmmc { + status = "okay"; + gpios = <&gpio 30 GPIO_ACTIVE_HIGH //fxs relay + &gpio 31 GPIO_ACTIVE_HIGH //still unknown + &gpio 3 GPIO_ACTIVE_HIGH>; //reset_slic? +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/VGV7510KW22BRN.dts b/target/linux/lantiq/files/arch/mips/boot/dts/VGV7510KW22BRN.dts new file mode 100644 index 0000000000..94b96d74d9 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/VGV7510KW22BRN.dts @@ -0,0 +1,65 @@ +/dts-v1/; + +#include "VGV7510KW22.dtsi" + +/ { + compatible = "arcadyan,vgv7510kw22-brn", "arcadyan,vgv7510kw22", "lantiq,xway", "lantiq,vr9"; + model = "o2 Box 6431"; + + sram@1f000000 { + cgu@103000 { + lantiq,phy-clk-src = <0x2>; + }; + }; +}; + +&localbus { + nor@0 { + partitions { + partition@0 { + label = "Boot"; + reg = <0x00000 0x40000>; + read-only; + }; + + partition@40000 { + label = "Configuration"; + reg = <0x40000 0x40000>; + read-only; + }; + + partition@80000 { + label = "Certificate"; + reg = <0x80000 0x20000>; + read-only; + }; + + partition@a0000 { + label = "Special_Area"; + reg = <0xa0000 0x20000>; + read-only; + }; + + partition@c0000 { + compatible = "brnboot,root-selector"; + label = "Primary_Setting"; + reg = <0xc0000 0x20000>; + read-only; + }; + + partition@e0000 { + label = "Code_Image_0"; + reg = <0xe0000 0x780000>; + brnboot,root-id = <0x00>; + read-only; + }; + + partition@860000 { + label = "Code_Image_1"; + reg = <0x860000 0x780000>; + brnboot,root-id = <0x01>; + read-only; + }; + }; + }; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/VGV7510KW22NOR.dts b/target/linux/lantiq/files/arch/mips/boot/dts/VGV7510KW22NOR.dts new file mode 100644 index 0000000000..cc84c63f2e --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/VGV7510KW22NOR.dts @@ -0,0 +1,31 @@ +/dts-v1/; + +#include "VGV7510KW22.dtsi" + +/ { + compatible = "arcadyan,vgv7510kw22-nor", "arcadyan,vgv7510kw22", "lantiq,xway", "lantiq,vr9"; + model = "o2 Box 6431"; +}; + +&localbus { + nor@0 { + partitions { + partition@0 { + label = "uboot"; + reg = <0x0 0x60000>; /* 384 KiB */ + read-only; + }; + + partition@60000 { + label = "uboot-env"; + reg = <0x60000 0x20000>; /* 128 KiB */ + read-only; + }; + + partition@80000 { + label = "firmware"; + reg = <0x80000 0xf60000>; /* 15744 KiB */ + }; + }; + }; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/VGV7519.dtsi b/target/linux/lantiq/files/arch/mips/boot/dts/VGV7519.dtsi new file mode 100644 index 0000000000..f69b302bcd --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/VGV7519.dtsi @@ -0,0 +1,314 @@ +#include "vr9.dtsi" + +#include +#include + +/ { + compatible = "arcadyan,vgv7519", "lantiq,xway", "lantiq,vr9"; + + chosen { + bootargs = "console=ttyLTQ0,115200 mem=62M vpe1_load_addr=0x83e00000 vpe1_mem=2M maxvpes=1 maxtcs=1 nosmp"; + }; + + aliases { + led-boot = &power_green; + led-failsafe = &power_red; + led-running = &power_green; + led-upgrade = &power_green; + + led-dsl = &broadband_green; + led-internet = &internet_green; + led-wifi = &wireless_green; + }; + + memory@0 { + reg = <0x0 0x4000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + reset { + label = "reset"; + gpios = <&gpio 9 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + eco { + label = "eco"; + gpios = <&gpio 41 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + rfkill { + label = "rfkill"; + gpios = <&gpio 45 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + wps { + label = "wps"; + gpios = <&gpio 10 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + eco { + label = "vgv7519:blue:eco"; + gpios = <&stp 2 GPIO_ACTIVE_LOW>; + }; + wps_red { + label = "vgv7519:red:wps"; + gpios = <&stp 3 GPIO_ACTIVE_LOW>; + }; + wps_green { + label = "vgv7519:green:wps"; + gpios = <&stp 4 GPIO_ACTIVE_LOW>; + }; + upgrade { + label = "vgv7519:blue:upgrade"; + gpios = <&stp 5 GPIO_ACTIVE_LOW>; + }; + tv { + label = "vgv7519:green:tv"; + gpios = <&stp 6 GPIO_ACTIVE_LOW>; + }; + internet_green: internet_green { + label = "vgv7519:green:internet"; + gpios = <&stp 7 GPIO_ACTIVE_LOW>; + }; + internet_red { + label = "vgv7519:red:internet"; + gpios = <&stp 8 GPIO_ACTIVE_LOW>; + }; + broadband_red { + label = "vgv7519:red:broadband"; + gpios = <&stp 9 GPIO_ACTIVE_LOW>; + }; + broadband_green: broadband_green { + label = "vgv7519:green:broadband"; + gpios = <&stp 10 GPIO_ACTIVE_LOW>; + }; + voice { + label = "vgv7519:green:voice"; + gpios = <&stp 11 GPIO_ACTIVE_LOW>; + }; + wireless_red { + label = "vgv7519:red:wireless"; + gpios = <&stp 12 GPIO_ACTIVE_LOW>; + }; + wireless_green: wireless_green { + label = "vgv7519:green:wireless"; + gpios = <&stp 13 GPIO_ACTIVE_LOW>; + }; + power_green: power2 { + label = "vgv7519:green:power"; + gpios = <&stp 14 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + power_red: power { + label = "vgv7519:red:power"; + gpios = <&stp 15 GPIO_ACTIVE_LOW>; + }; + }; + + usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio 32 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +ð0 { + lan: interface@0 { + compatible = "lantiq,xrx200-pdi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + mtd-mac-address = <&boardconfig 0x16>; + mtd-mac-address-increment = <1>; + lantiq,switch; + + ethernet@0 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <0>; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + }; + ethernet@1 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <1>; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + }; + ethernet@2 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <2>; + phy-mode = "gmii"; + phy-handle = <&phy11>; + }; + ethernet@4 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <4>; + phy-mode = "gmii"; + phy-handle = <&phy13>; + }; + ethernet@5 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <5>; + phy-mode = "rgmii"; + phy-handle = <&phy5>; + }; + }; + + mdio@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-mdio"; + reg = <0>; + + phy0: ethernet-phy@0 { + reg = <0x0>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + phy1: ethernet-phy@1 { + reg = <0x1>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + phy5: ethernet-phy@5 { + reg = <0x5>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + phy11: ethernet-phy@11 { + reg = <0x11>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + phy13: ethernet-phy@13 { + reg = <0x13>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + }; +}; + +&gphy0 { + lantiq,gphy-mode = ; +}; + +&gphy1 { + lantiq,gphy-mode = ; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + stp { + lantiq,groups = "stp"; + lantiq,function = "stp"; + lantiq,open-drain = <0>; + lantiq,output = <1>; + lantiq,pull = <0>; + }; + mdio { + lantiq,groups = "mdio"; + lantiq,function = "mdio"; + }; + pci-rst { + lantiq,pins = "io21"; + lantiq,open-drain = <0>; + lantiq,pull = <0>; + lantiq,output = <1>; + }; + gphy-leds { + lantiq,groups = "gphy0 led1", "gphy1 led0"; + lantiq,function = "gphy"; + lantiq,open-drain = <0>; + lantiq,pull = <0>; + lantiq,output = <1>; + }; + }; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x800000>, <1 0x800000 0x800000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + boardconfig: partition@40000 { + label = "board_config"; + reg = <0x40000 0x10000>; + read-only; + }; + }; + }; +}; + +&pci0 { + status = "okay"; + gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; + + wifi@1814,3091 { + compatible = "pci1814,3091"; + reg = <0x7000 0 0 0 0>; + ralink,mtd-eeprom = <&boardconfig 0x410>; + ralink,mtd-eeprom-swap; + mtd-mac-address = <&boardconfig 0x16>; + mtd-mac-address-increment = <1>; + }; +}; + +&pcie0 { + status = "disabled"; +}; + +&stp { + status = "okay"; + lantiq,shadow = <0xffff>; + lantiq,groups = <0x3>; + lantiq,dsl = <0x0>; + lantiq,phy1 = <0x0>; + lantiq,phy2 = <0x0>; + /* lantiq,rising; */ +}; + +&usb_phy0 { + status = "okay"; +}; + +&usb_phy1 { + status = "okay"; +}; + +&usb0 { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; + +&usb1 { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; + +&vmmc { + status = "okay"; + gpios = <&gpio 30 GPIO_ACTIVE_HIGH //fxs relay + &gpio 31 GPIO_ACTIVE_HIGH //still unknown + &gpio 3 GPIO_ACTIVE_HIGH>; //reset_slic? +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/VGV7519BRN.dts b/target/linux/lantiq/files/arch/mips/boot/dts/VGV7519BRN.dts new file mode 100644 index 0000000000..1e6a65ebb0 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/VGV7519BRN.dts @@ -0,0 +1,70 @@ +/dts-v1/; + +#include "VGV7519.dtsi" + +/ { + compatible = "arcadyan,vgv7519-brn", "arcadyan,vgv7519", "lantiq,xway", "lantiq,vr9"; + model = "KPN Experiabox V8"; +}; + +&localbus { + nor@0 { + partitions { + partition@0 { + label = "Boot"; + reg = <0x00000 0x40000>; + read-only; + }; + + partition@50000 { + label = "Certificate"; + reg = <0x50000 0x10000>; + read-only; + }; + partition@60000 { + label = "Special_Area"; + reg = <0x60000 0x10000>; + read-only; + }; + + partition@70000 { + label = " Reserve_0"; + reg = <0x70000 0x10000>; + read-only; + }; + + partition@80000 { + label = "Code_Image_0"; + reg = <0x80000 0x780000>; + brnboot,root-id = <0x00>; + read-only; + }; + + partition@4000000 { + compatible = "brnboot,root-selector"; + label = "Primary_Setting"; + reg = <0x4000000 0x10000>; + read-only; + }; + + partition@4010000 { + label = "Configuration"; + reg = <0x4010000 0x60000>; + read-only; + }; + + partition@4070000 { + label = " Reserve_1"; + reg = <0x4070000 0x10000>; + read-only; + }; + + partition@4080000 { + label = "Code_Image_1"; + reg = <0x4080000 0x780000>; + brnboot,root-id = <0x01>; + read-only; + }; + }; + }; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/VGV7519NOR.dts b/target/linux/lantiq/files/arch/mips/boot/dts/VGV7519NOR.dts new file mode 100644 index 0000000000..4bdf0bc753 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/VGV7519NOR.dts @@ -0,0 +1,29 @@ +/dts-v1/; + +#include "VGV7519.dtsi" + +/ { + compatible = "arcadyan,vgv7519-nor", "arcadyan,vgv7519", "lantiq,xway", "lantiq,vr9"; + model = "KPN Experiabox V8"; +}; + +&localbus { + nor@0 { + partitions { + partition@0 { + label = "uboot"; + reg = <0x00000 0x40000>; + read-only; + }; + partition@60000 { + label = "uboot_env"; + reg = <0x60000 0x10000>; + read-only; + }; + partition@80000 { + label = "firmware"; + reg = <0x80000 0xf80000>; + }; + }; + }; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/VR200.dts b/target/linux/lantiq/files/arch/mips/boot/dts/VR200.dts new file mode 100644 index 0000000000..74f666ddfd --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/VR200.dts @@ -0,0 +1,94 @@ +/dts-v1/; + +#include "VR200.dtsi" + +/ { + compatible = "tplink,vr200", "lantiq,xway", "lantiq,vr9"; + model = "TP-LINK Archer VR200"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power; + led-failsafe = &power; + led-running = &power; + led-upgrade = &power; + + led-dsl = &dsl; + led-internet = &internet; + led-wifi = &wlan5g; + + led-usb = &led_usb; + led-usb2 = &led_usb; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + reset { + label = "reset"; + gpios = <&gpio 22 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wifi { + label = "wifi"; + gpios = <&gpio 0 GPIO_ACTIVE_HIGH>; + linux,code = ; + linux,input-type = ; + }; + + wps { + label = "wps"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + led { + label = "led"; + gpios = <&gpio 39 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + power: power { + label = "vr200:blue:power"; + gpios = <&gpio 46 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + dsl: dsl { + label = "vr200:blue:dsl"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + internet: internet { + label = "vr200:blue:internet"; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + }; + led_usb: usb { + label = "vr200:blue:usb"; + gpios = <&gpio 25 GPIO_ACTIVE_LOW>; + }; + eth { + label = "vr200:blue:lan"; + gpios = <&gpio 40 GPIO_ACTIVE_LOW>; + }; + wlan { + label = "vr200:blue:wlan"; + gpios = <&gpio 24 GPIO_ACTIVE_LOW>; + }; + wlan5g: wifi { + label = "vr200:blue:wlan5g"; + gpios = <&gpio 20 GPIO_ACTIVE_LOW>; + }; + led_wps { + label = "vr200:blue:wps"; + gpios = <&gpio 44 GPIO_ACTIVE_LOW>; + }; + }; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/VR200.dtsi b/target/linux/lantiq/files/arch/mips/boot/dts/VR200.dtsi new file mode 100644 index 0000000000..dcfa86125d --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/VR200.dtsi @@ -0,0 +1,219 @@ +#include "vr9.dtsi" + +#include +#include + +/ { + memory@0 { + reg = <0x0 0x7f00000>; + }; + + usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio 33 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +ð0 { + lan: interface@0 { + compatible = "lantiq,xrx200-pdi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + mtd-mac-address = <&romfile 0xf100>; + lantiq,switch; + + ethernet@0 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <0>; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + // gpios = <&gpio 42 GPIO_ACTIVE_LOW>; + }; + ethernet@5 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <5>; + phy-mode = "rgmii"; + phy-handle = <&phy5>; + }; + ethernet@2 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <2>; + phy-mode = "gmii"; + phy-handle = <&phy11>; + }; + ethernet@3 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <4>; + phy-mode = "gmii"; + phy-handle = <&phy13>; + }; + }; + + mdio@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-mdio"; + reg = <0>; + + phy0: ethernet-phy@0 { + reg = <0x0>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + phy5: ethernet-phy@5 { + reg = <0x5>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + phy11: ethernet-phy@11 { + reg = <0x11>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + phy13: ethernet-phy@13 { + reg = <0x13>; + compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; + }; + }; +}; + +&gphy0 { + lantiq,gphy-mode = ; +}; + +&gphy1 { + lantiq,gphy-mode = ; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + mdio { + lantiq,groups = "mdio"; + lantiq,function = "mdio"; + }; + gphy-leds { + lantiq,groups = "gphy0 led1", "gphy1 led1"; + lantiq,function = "gphy"; + lantiq,pull = <2>; + lantiq,open-drain = <0>; + lantiq,output = <1>; + }; + phy-rst { + lantiq,pins = "io42"; + lantiq,pull = <0>; + lantiq,open-drain = <0>; + lantiq,output = <1>; + }; + pcie-rst { + lantiq,pins = "io38"; + lantiq,pull = <0>; + lantiq,output = <1>; + }; + }; + pins_spi_default: pins_spi_default { + spi_in { + lantiq,groups = "spi_di"; + lantiq,function = "spi"; + }; + spi_out { + lantiq,groups = "spi_do", "spi_clk", + "spi_cs4"; + lantiq,function = "spi"; + lantiq,output = <1>; + }; + }; +}; + +&pci0 { + status = "okay"; + gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>; +}; + +&spi { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pins_spi_default>; + + m25p80@4 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <4 0>; + spi-max-frequency = <33250000>; + m25p,fast-read; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + reg = <0x0 0x20000>; + label = "u-boot"; + read-only; + }; + + partition@20000 { + reg = <0x20000 0xf90000>; + label = "firmware"; + }; + + partition@fb0000 { + reg = <0xfb0000 0x10000>; + label = "radioDECT"; + read-only; + }; + + partition@fc0000 { + reg = <0xfc0000 0x10000>; + label = "config"; + read-only; + }; + + romfile: partition@fd0000 { + reg = <0xfd0000 0x10000>; + label = "romfile"; + read-only; + }; + + partition@fe0000 { + reg = <0xfe0000 0x10000>; + label = "rom"; + read-only; + }; + + partition@ff0000 { + reg = <0xff0000 0x10000>; + label = "radio"; + read-only; + }; + }; + }; +}; + +&usb_phy0 { + status = "okay"; +}; + +&usb_phy1 { + status = "okay"; +}; + +&usb0 { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; + +&usb1 { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/VR200v.dts b/target/linux/lantiq/files/arch/mips/boot/dts/VR200v.dts new file mode 100644 index 0000000000..dc65dbfc36 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/VR200v.dts @@ -0,0 +1,101 @@ +/dts-v1/; + +#include "VR200.dtsi" + +/ { + compatible = "tplink,vr200v", "lantiq,xway", "lantiq,vr9"; + model = "TP-LINK Archer VR200v"; + + chosen { + bootargs = "console=ttyLTQ0,115200 mem=126M vpe1_load_addr=0x87e00000 vpe1_mem=2M maxvpes=1 maxtcs=1 nosmp"; + }; + + aliases { + led-boot = &power; + led-failsafe = &power; + led-running = &power; + led-upgrade = &power; + + led-dsl = &dsl; + led-internet = &internet; + led-wifi = &wlan5g; + + led-usb = &led_usb; + led-usb2 = &led_usb; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + reset { + label = "reset"; + gpios = <&gpio 22 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wifi { + label = "wifi"; + gpios = <&gpio 0 GPIO_ACTIVE_HIGH>; + linux,code = ; + linux,input-type = ; + }; + + wps { + label = "wps"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + dect_paging { + label = "dect_paging"; + gpios = <&gpio 39 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + power: power { + label = "vr200v:blue:power"; + gpios = <&gpio 46 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + dsl: dsl { + label = "vr200v:blue:dsl"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + internet: internet { + label = "vr200v:blue:internet"; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + }; + led_usb: usb { + label = "vr200v:blue:usb"; + gpios = <&gpio 25 GPIO_ACTIVE_LOW>; + }; + eth { + label = "vr200v:blue:lan"; + gpios = <&gpio 40 GPIO_ACTIVE_LOW>; + }; + wlan { + label = "vr200v:blue:wlan"; + gpios = <&gpio 24 GPIO_ACTIVE_LOW>; + }; + wlan5g: wifi { + label = "vr200v:blue:wlan5g"; + gpios = <&gpio 20 GPIO_ACTIVE_LOW>; + }; + phone { + label = "vr200v:blue:phone"; + gpios = <&gpio 44 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&vmmc { + status = "okay"; + gpios = <&gpio 30 GPIO_ACTIVE_HIGH //fxs relay + &gpio 31 GPIO_ACTIVE_HIGH //still unknown + &gpio 3 GPIO_ACTIVE_HIGH>; //reset_slic? +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/WBMR.dts b/target/linux/lantiq/files/arch/mips/boot/dts/WBMR.dts new file mode 100644 index 0000000000..9759b311b7 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/WBMR.dts @@ -0,0 +1,200 @@ +/dts-v1/; + +#include "ar9.dtsi" + +#include + +/ { + compatible = "buffalo,wbmr-hp-g300h", "lantiq,xway", "lantiq,ar9"; + model = "Buffalo WBMR-HP-G300H"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power_green; + led-failsafe = &power_red; + led-running = &power_green; + led-upgrade = &power_green; + + led-dsl = &dsl; + led-internet = &online_green; + led-usb = &led_usb; + led-wifi = &wifi; + }; + + memory@0 { + reg = <0x0 0x4000000>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + wps { + label = "wps"; + gpios = <&gpio 0 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + reset { + label = "reset"; + gpios = <&gpio 37 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + eject { + label = "eject"; + gpios = <&gpio 34 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + movie { + label = "movie"; + gpios = <&gpio 22 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + power_green: power { + label = "wbmr:green:power"; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + power_red: power2 { + label = "wbmr:red:power"; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + }; + security { + label = "wbmr:yellow:security"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + }; + wifi: wifi { + label = "wbmr:green:wireless"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + }; + dsl: dsl { + label = "wbmr:green:dsl"; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + }; + online_green: online { + label = "wbmr:green:internet"; + gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + }; + online2 { + label = "wbmr:red:internet"; + gpios = <&gpio 18 GPIO_ACTIVE_LOW>; + }; + movie { + label = "wbmr:blue:movie"; + gpios = <&gpio 20 GPIO_ACTIVE_LOW>; + }; + led_usb: usb { + label = "wbmr:green:usb"; + gpios = <&gpio 28 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + }; + + usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio 36 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + pci-in { + lantiq,groups = "req1"; + lantiq,output = <0>; + lantiq,open-drain = <1>; + lantiq,pull = <2>; + }; + pci-out { + lantiq,groups = "gnt1"; + lantiq,output = <1>; + lantiq,pull = <0>; + }; + pci_rst { + lantiq,pins = "io21"; + lantiq,pull = <0>; + lantiq,output = <1>; + }; + }; +}; + +&gsw { + phy-mode = "rgmii"; + mtd-mac-address = <&boardconfig 0x10024>; +}; + +&pci0 { + status = "okay"; +}; + +&localbus { + nor@0 { + compatible = "lantiq,nor"; + bank-width = <2>; + reg = <0 0x0 0x2000000>; + #address-cells = <1>; + #size-cells = <1>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "uboot"; + reg = <0x00000 0x40000>; + read-only; + }; + + partition@40000 { + label = "uboot_env"; + reg = <0x40000 0x20000>; + read-only; + }; + + partition@20000 { + label = "firmware"; + reg = <0x60000 0x1f20000>; + }; + + boardconfig: partition@1fc0000 { + label = "board"; + reg = <0x1fc0000 0x20000>; + read-only; + }; + + partition@1fe0000 { + label = "calibration"; + reg = <0x1fe0000 0x20000>; + read-only; + }; + }; + }; +}; + +&usb_phy0 { + status = "okay"; +}; + +&usb0 { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/WBMR300.dts b/target/linux/lantiq/files/arch/mips/boot/dts/WBMR300.dts new file mode 100644 index 0000000000..5dcf13912e --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/WBMR300.dts @@ -0,0 +1,330 @@ +/dts-v1/; + +#include "vr9.dtsi" + +#include +#include + +/ { + compatible = "buffalo,wbmr-300hpd", "lantiq,xway", "lantiq,vr9"; + model = "Buffalo WBMR-300HPD"; + + chosen { + bootargs = "console=ttyLTQ0,115200"; + }; + + aliases { + led-boot = &power_g; + led-failsafe = &diag_r; + led-running = &power_g; + led-upgrade = &power_g; + + led-dsl = &dsl; + led-internet = &router_g; + led-wifi = &wifi_g; + }; + + memory@0 { + reg = <0x0 0x4000000>; + }; + + gpio_poweroff { + compatible = "gpio-poweroff"; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + power { + label = "power"; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + reset { + label = "reset"; + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&gpio 31 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + auto { + label = "auto"; + gpios = <&gpio 48 GPIO_ACTIVE_HIGH>; + linux,code = ; + linux,input-type = ; + }; + + router { + label = "router"; + gpios = <&gpio 2 GPIO_ACTIVE_HIGH>; + linux,code = ; + linux,input-type = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + diag_r: diag_r { + label = "wbmr300:red:diag"; + gpios = <&gpio 0 GPIO_ACTIVE_HIGH>; + default_state = "off"; + }; + + wifi_g: wifi_g { + label = "wbmr300:green:wifi"; + gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; + }; + + dsl: dsl { + label = "dsl"; + gpios = <&gpio 4 GPIO_ACTIVE_HIGH>; + }; + + router_y: router_y { + label = "wbmr300:yellow:router"; + gpios = <&gpio 8 GPIO_ACTIVE_HIGH>; + }; + + wifi_y: wifi_y { + label = "wbmr300:yellow:wifi"; + gpios = <&gpio 9 GPIO_ACTIVE_HIGH>; + }; + + lan1: lan1 { + label = "wbmr300:green:lan1"; + gpios = <&gpio 11 GPIO_ACTIVE_HIGH>; + }; + + wan: wan { + label = "wbmr300:green:wan"; + gpios = <&gpio 12 GPIO_ACTIVE_HIGH>; + }; + + lan3: lan3 { + label = "wbmr300:green:lan3"; + gpios = <&gpio 15 GPIO_ACTIVE_HIGH>; + }; + + lan2: lan2 { + label = "wbmr300:green:lan2"; + gpios = <&gpio 33 GPIO_ACTIVE_HIGH>; + }; + + internet_g: internet_g { + label = "wbmr300:green:internet"; + gpios = <&gpio 34 GPIO_ACTIVE_HIGH>; + }; + + internet_y: internet_y { + label = "wbmr300:yellow:internet"; + gpios = <&gpio 35 GPIO_ACTIVE_HIGH>; + }; + + router_g: router_g { + label = "wbmr300:green:router"; + gpios = <&gpio 36 GPIO_ACTIVE_HIGH>; + }; + + power_g: power_g { + label = "wbmr300:green:power"; + gpios = <&gpio 49 GPIO_ACTIVE_HIGH>; + }; + }; + + usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + + regulator-name = "USB_VBUS"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio 33 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +ð0 { + lan: interface@0 { + compatible = "lantiq,xrx200-pdi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + lantiq,switch; + + ethernet@1 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <4>; + phy-mode = "mii"; + phy-handle = <&phy13>; + }; + ethernet@2 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <5>; + phy-mode = "mii"; + phy-handle = <&phy14>; + }; + ethernet@3 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <2>; + phy-mode = "mii"; + phy-handle = <&phy11>; + }; + ethernet@4 { + compatible = "lantiq,xrx200-pdi-port"; + reg = <3>; + phy-mode = "mii"; + phy-handle = <&phy12>; + }; + }; + + mdio@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-mdio"; + reg = <0>; + + phy11: ethernet-phy@11 { + reg = <0x11>; + compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; + }; + phy12: ethernet-phy@12 { + reg = <0x12>; + compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; + }; + phy13: ethernet-phy@13 { + reg = <0x13>; + compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; + }; + phy14: ethernet-phy@14 { + reg = <0x14>; + compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; + }; + }; +}; + +&gphy0 { + lantiq,gphy-mode = ; +}; + +&gphy1 { + lantiq,gphy-mode = ; +}; + +&gpio { + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinmux { + mdio { + lantiq,groups = "mdio"; + lantiq,function = "mdio"; + }; + phy-rst { + lantiq,pins = "io42"; + lantiq,pull = <0>; + lantiq,open-drain = <0>; + lantiq,output = <1>; + }; + pcie-rst { + lantiq,pins = "io38"; + lantiq,pull = <0>; + lantiq,output = <1>; + }; + }; + pins_spi_default: pins_spi_default { + spi_in { + lantiq,groups = "spi_di"; + lantiq,function = "spi"; + }; + spi_out { + lantiq,groups = "spi_do", "spi_clk", + "spi_cs4"; + lantiq,function = "spi"; + lantiq,output = <1>; + }; + }; +}; + +&spi { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pins_spi_default>; + + m25p80@4 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <4 0>; + spi-max-frequency = <20000000>; + + partition@0 { + reg = <0x0 0x10000>; + label = "u-boot"; + read-only; + }; + + partition@10000 { + reg = <0x10000 0x10000>; + label = "gphyfirmware"; + read-only; + }; + + partition@20000 { + reg = <0x20000 0x80000>; + label = "dsl_fw"; + }; + + partition@de0000 { + reg = <0xa0000 0xf40000>; + label = "firmware"; + }; + + partition@fe0000 { + reg = <0xfe0000 0x10000>; + label = "sysconfig"; + read-only; + }; + + partition@ff0000 { + reg = <0xff0000 0x2000>; + label = "ubootconfig"; + }; + + partition@ff3000 { + reg = <0xff3000 0x2000>; + label = "board_config"; + read-only; + }; + }; +}; + +&usb_phy0 { + status = "okay"; +}; + +&usb_phy1 { + status = "okay"; +}; + +&usb0 { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; + +&usb1 { + status = "okay"; + vbus-supply = <&usb_vbus>; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/amazonse.dtsi b/target/linux/lantiq/files/arch/mips/boot/dts/amazonse.dtsi new file mode 100644 index 0000000000..f216adf36f --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/amazonse.dtsi @@ -0,0 +1,204 @@ +#include + +/ { + #address-cells = <1>; + #size-cells = <1>; + compatible = "lantiq,xway", "lantiq,ase"; + + aliases { + serial0 = &asc1; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + cpus { + cpu@0 { + compatible = "mips,mips4Kc"; + }; + }; + + memory@0 { + device_type = "memory"; + }; + + biu@1f800000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "lantiq,biu", "simple-bus"; + reg = <0x1f800000 0x800000>; + ranges = <0x0 0x1f800000 0x7fffff>; + + icu0: icu@80200 { + #interrupt-cells = <1>; + interrupt-controller; + compatible = "lantiq,icu"; + reg = <0x80200 0x28 + 0x80228 0x28 + 0x80250 0x28 + 0x80278 0x28 + 0x802a0 0x28>; + }; + + watchdog@803f0 { + compatible = "lantiq,wdt"; + reg = <0x803f0 0x10>; + }; + }; + + sram@1f000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "lantiq,sram", "simple-bus"; + reg = <0x1f000000 0x800000>; + ranges = <0x0 0x1f000000 0x7fffff>; + + eiu0: eiu@101000 { + #interrupt-cells = <1>; + interrupt-controller; + compatible = "lantiq,eiu-xway"; + reg = <0x101000 0x1000>; + interrupt-parent = <&icu0>; + lantiq,eiu-irqs = <29 30 31>; + }; + + pmu0: pmu@102000 { + compatible = "lantiq,pmu-xway"; + reg = <0x102000 0x1000>; + }; + + cgu0: cgu@103000 { + compatible = "lantiq,cgu-xway"; + reg = <0x103000 0x1000>; + #clock-cells = <1>; + }; + + rcu0: rcu@203000 { + compatible = "lantiq,ase-rcu", "simple-mfd", "syscon"; + reg = <0x203000 0x1000>; + ranges = <0x0 0x203000 0x100>; + big-endian; + + reset: reset-controller@10 { + compatible = "lantiq,danube-reset"; + reg = <0x10 4>, <0x14 4>; + + #reset-cells = <2>; + }; + + usb_phy: usb2-phy@18 { + compatible = "lantiq,ase-usb2-phy"; + reg = <0x18 4>; + status = "disabled"; + + resets = <&reset 4 4>; + reset-names = "ctrl"; + #phy-cells = <0>; + }; + + reboot@10 { + compatible = "syscon-reboot"; + reg = <0x10 4>; + + regmap = <&rcu0>; + offset = <0x10>; + mask = <0x40000000>; + }; + }; + }; + + fpi@10000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "lantiq,fpi", "simple-bus"; + ranges = <0x0 0x10000000 0xeefffff>; + reg = <0x10000000 0xef00000>; + + localbus: localbus@0 { + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x0 0x3ffffff /* addrsel0 */ + 1 0 0x4000000 0x4000010>; /* addsel1 */ + compatible = "lantiq,localbus", "simple-bus"; + }; + + spi: spi@e100800 { + compatible = "lantiq,ase-spi"; + reg = <0xe100800 0x100>; + interrupt-parent = <&icu0>; + interrupts = <24 25 26>; + interrupt-names = "spi_rx", "spi_tx", "spi_err", + "spi_frm"; + #address-cells = <1>; + #size-cells = <1>; + status = "disabled"; + }; + + gptu@e100a00 { + compatible = "lantiq,gptu-xway"; + reg = <0xe100a00 0x100>; + interrupt-parent = <&icu0>; + interrupts = <33 34 35 36 37 38>; + }; + + gpio: pinmux@e100b10 { + compatible = "lantiq,ase-pinctrl"; + #gpio-cells = <2>; + gpio-controller; + reg = <0xe100b10 0xa0>; + }; + + asc1: serial@e100c00 { + compatible = "lantiq,asc"; + reg = <0xe100c00 0x400>; + interrupt-parent = <&icu0>; + interrupts = <72 74 75>; + }; + + mei@e116000 { + compatible = "lantiq,mei-xway"; + interrupt-parent = <&icu0>; + interrupts = <81>; + }; + + usb: usb@e101000 { + compatible = "lantiq,ase-usb"; + reg = <0xe101000 0x1000 + 0xe120000 0x3f000>; + interrupt-parent = <&icu0>; + interrupts = <39>; + dr_mode = "host"; + phys = <&usb_phy>; + phy-names = "usb2-phy"; + status = "disabled"; + }; + + dma0: dma@e104100 { + compatible = "lantiq,dma-xway"; + reg = <0xe104100 0x800>; + }; + + ebu0: ebu@e105300 { + compatible = "lantiq,ebu-xway"; + reg = <0xe105300 0x100>; + }; + + ppe@e234000 { + compatible = "lantiq,ppe-ase"; + interrupt-parent = <&icu0>; + interrupts = <85>; + }; + + gsw: etop@e180000 { + compatible = "lantiq,etop-xway"; + reg = <0xe180000 0x40000>; + interrupt-parent = <&icu0>; + interrupts = <105 109>; + }; + }; + + adsl { + compatible = "lantiq,adsl-ase"; + }; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/ar9.dtsi b/target/linux/lantiq/files/arch/mips/boot/dts/ar9.dtsi new file mode 100644 index 0000000000..48e0d95d63 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/ar9.dtsi @@ -0,0 +1,268 @@ +#include + +/ { + #address-cells = <1>; + #size-cells = <1>; + compatible = "lantiq,xway", "lantiq,ar9"; + + aliases { + serial0 = &asc1; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + cpus { + cpu@0 { + compatible = "mips,mips34K"; + }; + }; + + memory@0 { + device_type = "memory"; + }; + + biu@1f800000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "lantiq,biu", "simple-bus"; + reg = <0x1f800000 0x800000>; + ranges = <0x0 0x1f800000 0x7fffff>; + + icu0: icu@80200 { + #interrupt-cells = <1>; + interrupt-controller; + compatible = "lantiq,icu"; + reg = <0x80200 0x28 + 0x80228 0x28 + 0x80250 0x28 + 0x80278 0x28 + 0x802a0 0x28>; + }; + + watchdog@803f0 { + compatible = "lantiq,xrx100-wdt", "lantiq,xrx100-wdt"; + reg = <0x803f0 0x10>; + + regmap = <&rcu0>; + }; + }; + + sram@1f000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "lantiq,sram", "simple-bus"; + reg = <0x1f000000 0x800000>; + ranges = <0x0 0x1f000000 0x7fffff>; + + eiu0: eiu@101000 { + #interrupt-cells = <1>; + interrupt-controller; + compatible = "lantiq,eiu-xway"; + reg = <0x101000 0x1000>; + interrupt-parent = <&icu0>; + lantiq,eiu-irqs = <166 135 66 40 41 42>; + }; + + pmu0: pmu@102000 { + compatible = "lantiq,pmu-xway"; + reg = <0x102000 0x1000>; + }; + + cgu0: cgu@103000 { + compatible = "lantiq,cgu-xway"; + reg = <0x103000 0x1000>; + #clock-cells = <1>; + }; + + rcu0: rcu@203000 { + compatible = "lantiq,xrx100-rcu", "simple-mfd", "syscon"; + reg = <0x203000 0x1000>; + ranges = <0x0 0x203000 0x100>; + big-endian; + + reset: reset-controller@10 { + compatible = "lantiq,xrx100-reset", "lantiq,danube-reset"; + reg = <0x10 4>, <0x14 4>; + + #reset-cells = <2>; + }; + + usb_phy0: usb2-phy@18 { + compatible = "lantiq,xrx100-usb2-phy"; + reg = <0x18 4>; + status = "disabled"; + + resets = <&reset 4 4>; + reset-names = "ctrl"; + #phy-cells = <0>; + }; + + usb_phy1: usb2-phy@34 { + compatible = "lantiq,xrx100-usb2-phy"; + reg = <0x34 4>; + status = "disabled"; + + resets = <&reset 28 28>; + reset-names = "ctrl"; + #phy-cells = <0>; + }; + + reboot@10 { + compatible = "syscon-reboot"; + reg = <0x10 4>; + + regmap = <&rcu0>; + offset = <0x10>; + mask = <0x40000000>; + }; + }; + }; + + fpi@10000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "lantiq,fpi", "simple-bus"; + ranges = <0x0 0x10000000 0xeefffff>; + reg = <0x10000000 0xef00000>; + + localbus: localbus@0 { + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x0 0x3ffffff /* addrsel0 */ + 1 0 0x4000000 0x4000010>; /* addsel1 */ + compatible = "lantiq,localbus", "simple-bus"; + }; + + gptu@e100a00 { + compatible = "lantiq,gptu-xway"; + reg = <0xe100a00 0x100>; + interrupt-parent = <&icu0>; + interrupts = <126 127 128 129 130 131>; + }; + + asc0: serial@e100400 { + compatible = "lantiq,asc"; + reg = <0xe100400 0x400>; + interrupt-parent = <&icu0>; + interrupts = <104 105 106>; + status = "disabled"; + }; + + spi: spi@e100800 { + compatible = "lantiq,xrx100-spi"; + reg = <0xe100800 0x100>; + interrupt-parent = <&icu0>; + interrupts = <22 23 24>; + interrupt-names = "spi_rx", "spi_tx", "spi_err", + "spi_frm"; + #address-cells = <1>; + #size-cells = <1>; + status = "disabled"; + }; + + gpio: pinmux@e100b10 { + compatible = "lantiq,xrx100-pinctrl"; + #gpio-cells = <2>; + gpio-controller; + reg = <0xe100b10 0xa0>; + }; + + stp: stp@e100bb0 { + #gpio-cells = <2>; + compatible = "lantiq,gpio-stp-xway"; + gpio-controller; + reg = <0xe100bb0 0x40>; + status = "disabled"; + }; + + asc1: serial@e100c00 { + compatible = "lantiq,asc"; + reg = <0xe100c00 0x400>; + interrupt-parent = <&icu0>; + interrupts = <112 113 114>; + }; + + usb0: usb@e101000 { + compatible = "lantiq,arx100-usb"; + reg = <0xe101000 0x1000 + 0xe120000 0x3f000>; + interrupt-parent = <&icu0>; + interrupts = <62 91>; + dr_mode = "host"; + phys = <&usb_phy0>; + phy-names = "usb2-phy"; + status = "disabled"; + }; + + usb1: usb@e106000 { + compatible = "lantiq,arx100-usb"; + reg = <0xe106000 0x1000 + 0xe1e0000 0x3f000>; + interrupt-parent = <&icu0>; + interrupts = <91>; + dr_mode = "host"; + phys = <&usb_phy1>; + phy-names = "usb2-phy"; + status = "disabled"; + }; + + deu@e103100 { + compatible = "lantiq,deu-arx100"; + reg = <0xe103100 0xf00>; + }; + + dma0: dma@e104100 { + compatible = "lantiq,dma-xway"; + reg = <0xe104100 0x800>; + }; + + ebu0: ebu@e105300 { + compatible = "lantiq,ebu-xway"; + reg = <0xe105300 0x100>; + }; + + mei@e116000 { + compatible = "lantiq,mei-xway"; + interrupt-parent = <&icu0>; + interrupts = <63>; + }; + + gsw: etop@e180000 { + compatible = "lantiq,etop-xway"; + reg = <0xe180000 0x40000 + 0xe108000 0x200>; + interrupt-parent = <&icu0>; + interrupts = <73 72>; + mac-address = [ 00 11 22 33 44 55 ]; + }; + + ppe@e234000 { + compatible = "lantiq,ppe-arx100"; + interrupt-parent = <&icu0>; + interrupts = <96>; + }; + + pci0: pci@e105400 { + status = "disabled"; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + compatible = "lantiq,pci-xway"; + bus-range = <0x0 0x0>; + ranges = <0x2000000 0 0x8000000 0x8000000 0 0x2000000 /* pci memory */ + 0x1000000 0 0x00000000 0xae00000 0 0x200000>; /* io space */ + reg = <0x7000000 0x8000 /* config space */ + 0xe105400 0x400>; /* pci bridge */ + lantiq,bus-clock = <33333333>; + interrupt-map-mask = <0xf800 0x0 0x0 0x7>; + interrupt-map = <0x7000 0 0 1 &icu0 30 1>; + req-mask = <0x1>; + }; + }; + + adsl { + compatible = "lantiq,adsl-arx100"; + }; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/danube.dtsi b/target/linux/lantiq/files/arch/mips/boot/dts/danube.dtsi new file mode 100644 index 0000000000..af4c795af2 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/danube.dtsi @@ -0,0 +1,252 @@ +#include + +/ { + #address-cells = <1>; + #size-cells = <1>; + compatible = "lantiq,xway", "lantiq,danube"; + + aliases { + serial0 = &asc1; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + cpus { + cpu@0 { + compatible = "mips,mips24Kc"; + }; + }; + + memory@0 { + device_type = "memory"; + }; + + biu@1f800000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "lantiq,biu", "simple-bus"; + reg = <0x1f800000 0x800000>; + ranges = <0x0 0x1f800000 0x7fffff>; + + icu0: icu@80200 { + #interrupt-cells = <1>; + interrupt-controller; + compatible = "lantiq,icu"; + reg = <0x80200 0x28 + 0x80228 0x28 + 0x80250 0x28 + 0x80278 0x28 + 0x802a0 0x28>; + }; + + watchdog@803f0 { + compatible = "lantiq,wdt"; + reg = <0x803f0 0x10>; + }; + }; + + sram@1f000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "lantiq,sram", "simple-bus"; + reg = <0x1f000000 0x800000>; + ranges = <0x0 0x1f000000 0x7fffff>; + + eiu0: eiu@101000 { + #interrupt-cells = <1>; + interrupt-controller; + compatible = "lantiq,eiu-xway"; + reg = <0x101000 0x1000>; + interrupt-parent = <&icu0>; + lantiq,eiu-irqs = <166 135 66>; + }; + + pmu0: pmu@102000 { + compatible = "lantiq,pmu-xway"; + reg = <0x102000 0x1000>; + }; + + cgu0: cgu@103000 { + compatible = "lantiq,cgu-xway"; + reg = <0x103000 0x1000>; + #clock-cells = <1>; + }; + + vmmc: vmmc@107000 { + status = "disabled"; + compatible = "lantiq,vmmc-xway"; + reg = <0x103000 0x400>; + interrupt-parent = <&icu0>; + interrupts = <150 151 152 153 154 155>; + }; + + rcu0: rcu@203000 { + compatible = "lantiq,danube-rcu", "simple-mfd", "syscon"; + reg = <0x203000 0x1000>; + ranges = <0x0 0x203000 0x100>; + big-endian; + + reset: reset-controller@10 { + compatible = "lantiq,danube-reset"; + reg = <0x10 4>, <0x14 4>; + + #reset-cells = <2>; + }; + + usb_phy: usb2-phy@18 { + compatible = "lantiq,danube-usb2-phy"; + reg = <0x18 4>; + status = "disabled"; + + resets = <&reset 4 4>; + reset-names = "ctrl"; + #phy-cells = <0>; + }; + + reboot@10 { + compatible = "syscon-reboot"; + reg = <0x10 4>; + + regmap = <&rcu0>; + offset = <0x10>; + mask = <0x40000000>; + }; + }; + }; + + fpi@10000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "lantiq,fpi", "simple-bus"; + ranges = <0x0 0x10000000 0xeefffff>; + reg = <0x10000000 0xef00000>; + + localbus: localbus@0 { + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x0 0x3ffffff /* addrsel0 */ + 1 0 0x4000000 0x4000010>; /* addsel1 */ + compatible = "lantiq,localbus", "simple-bus"; + + gpiomm: gpiomm@1 { + compatible = "lantiq,gpio-mm"; + reg = <1 0x0 0x10 >; + #address-cells = <1>; + #size-cells = <1>; + #gpio-cells = <2>; + gpio-controller; + status = "disabled"; + }; + }; + + gptu@e100a00 { + compatible = "lantiq,gptu-xway"; + reg = <0xe100a00 0x100>; + interrupt-parent = <&icu0>; + interrupts = <126 127 128 129 130 131>; + }; + + gpios: stp@e100bb0 { + #gpio-cells = <2>; + compatible = "lantiq,gpio-stp-xway"; + gpio-controller; + reg = <0xe100bb0 0x40>; + lantiq,shadow = <0xfff>; + lantiq,groups = <0x3>; + status = "disabled"; + }; + + asc0: serial@e100400 { + compatible = "lantiq,asc"; + reg = <0xe100400 0x400>; + interrupt-parent = <&icu0>; + interrupts = <104 105 106>; + status = "disabled"; + }; + + gpio: pinmux@e100b10 { + compatible = "lantiq,danube-pinctrl"; + #gpio-cells = <2>; + gpio-controller; + reg = <0xe100b10 0xa0>; + }; + + asc1: serial@e100c00 { + compatible = "lantiq,asc"; + reg = <0xe100c00 0x400>; + interrupt-parent = <&icu0>; + interrupts = <112 113 114>; + }; + + usb: usb@e101000 { + compatible = "lantiq,danube-usb"; + reg = <0xe101000 0x1000 + 0xe120000 0x3f000>; + interrupt-parent = <&icu0>; + interrupts = <62>; + dr_mode = "host"; + phys = <&usb_phy>; + phy-names = "usb2-phy"; + status = "disabled"; + }; + + deu@e103100 { + compatible = "lantiq,deu-danube"; + reg = <0xe103100 0xf00>; + }; + + dma0: dma@e104100 { + compatible = "lantiq,dma-xway"; + reg = <0xe104100 0x800>; + }; + + ebu0: ebu@e105300 { + compatible = "lantiq,ebu-xway"; + reg = <0xe105300 0x100>; + }; + + mei@e116000 { + compatible = "lantiq,mei-xway"; + interrupt-parent = <&icu0>; + interrupts = <63>; + }; + + gsw: etop@e180000 { + compatible = "lantiq,etop-xway"; + reg = <0xe180000 0x40000>; + interrupt-parent = <&icu0>; + interrupts = <73 78>; + mac-address = [ 00 11 22 33 44 55 ]; + }; + + ppe@e234000 { + compatible = "lantiq,ppe-danube"; + interrupt-parent = <&icu0>; + interrupts = <96>; + }; + + pci0: pci@e105400 { + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + compatible = "lantiq,pci-xway"; + bus-range = <0x0 0x0>; + ranges = <0x2000000 0 0x8000000 0x8000000 0 0x2000000 /* pci memory */ + 0x1000000 0 0x00000000 0xae00000 0 0x200000>; /* io space */ + reg = <0x7000000 0x8000 /* config space */ + 0xe105400 0x400>; /* pci bridge */ + lantiq,bus-clock = <33333333>; + interrupt-map-mask = <0xf800 0x0 0x0 0x7>; + interrupt-map = <0x7000 0 0 1 &icu0 30 1>; /* slot 14, irq 30 */ + req-mask = <0x1>; /* GNT1 */ + }; + }; + + adsl { + compatible = "lantiq,adsl-danube"; + }; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/falcon-sflash-16M.dtsi b/target/linux/lantiq/files/arch/mips/boot/dts/falcon-sflash-16M.dtsi new file mode 100644 index 0000000000..d95acc21ef --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/falcon-sflash-16M.dtsi @@ -0,0 +1,37 @@ + +&ebu_cs0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "lantiq,sflash-falcon", "simple-bus"; + + flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spansion,s25fl129p0", "spansion,s25fl129p1"; + reg = <0 0>; + linux,mtd-name = "sflash"; + spi-max-frequency = <80000000>; + m25p,fast-read; + + partition@0 { + reg = <0x0 0x40000>; + label = "uboot"; + read-only; + }; + + partition@40000 { + reg = <0x40000 0x80000>; + label = "uboot_env"; + }; + + partition@C0000 { + reg = <0xC0000 0x740000>; + label = "image0"; + }; + + partition@800000 { + reg = <0x800000 0x800000>; + label = "image1"; + }; + }; +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/falcon.dtsi b/target/linux/lantiq/files/arch/mips/boot/dts/falcon.dtsi new file mode 100644 index 0000000000..98f71819a2 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/falcon.dtsi @@ -0,0 +1,392 @@ +/ { + #address-cells = <1>; + #size-cells = <1>; + compatible = "lantiq,falcon"; + + cpus { + cpu@0 { + compatible = "mips,mips34kc"; + }; + }; + + aliases { + serial0 = &serial0; + serial1 = &serial1; + gpio0 = &gpio0; + gpio1 = &gpio1; + gpio2 = &gpio2; + gpio3 = &gpio3; + gpio4 = &gpio4; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + clocks { + compatible = "simple-bus"; + + cpu_clk: cpu { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <400000000>; + clock-output-names = "cpu"; + }; + + io_clk: io { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <200000000>; + clock-output-names = "io"; + }; + + fpi_clk: fpi { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <100000000>; + clock-output-names = "fpi"; + }; + }; + + ebu_cs0: localbus@10000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "lantiq,localbus", "simple-bus"; + reg = <0x10000000 0x4000000>; + ranges = <0x0 0x10000000 0x4000000>; + }; + ebu_cs1: localbus@14000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "lantiq,localbus", "simple-bus"; + reg = <0x14000000 0x4000000>; + ranges = <0x0 0x14000000 0x4000000>; + }; + + ebu@18000000 { + compatible = "lantiq,ebu-falcon"; + reg = <0x18000000 0x100>; + }; + + sbs2@1D000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "lantiq,sysb2", "simple-bus"; + reg = <0x1D000000 0x1000000>; + ranges = <0x0 0x1D000000 0x1000000>; + + clock_sysgpe: clock-controller@700000 { + compatible = "lantiq,sysgpe-falcon"; + reg = <0x700000 0x100>; + #clock-cells = <1>; + }; + + mps@4000 { + compatible = "lantiq,mps-falcon", "lantiq,mps-xrx100"; + reg = <0x4000 0x1000>; + interrupt-parent = <&icu0>; + interrupts = <154 155>; + lantiq,mbx = <&mpsmbx>; + }; + + gpio0: gpio@810000 { + compatible = "lantiq,falcon-gpio"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&icu0>; + interrupts = <44>; + reg = <0x810000 0x80>; + clocks = <&clock_syseth 16>; + }; + + gpio2: gpio@810100 { + compatible = "lantiq,falcon-gpio"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&icu0>; + interrupts = <46>; + reg = <0x810100 0x80>; + clocks = <&clock_syseth 17>; + }; + + clock_syseth: clock-controller@B00000 { + compatible = "lantiq,syseth-falcon"; + reg = <0xB00000 0x100>; + #clock-cells = <1>; + }; + + pad@B01000 { + compatible = "lantiq,pad-falcon"; + reg = <0xB01000 0x100>; + lantiq,bank = <0>; + clocks = <&clock_syseth 20>; + }; + + pad@B02000 { + compatible = "lantiq,pad-falcon"; + reg = <0xB02000 0x100>; + lantiq,bank = <2>; + clocks = <&clock_syseth 21>; + }; + }; + + fpi@1E000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "lantiq,fpi", "simple-bus"; + reg = <0x1E000000 0x1000000>; + ranges = <0x0 0x1E000000 0x1000000>; + + serial1: serial@100B00 { + status = "disabled"; + compatible = "lantiq,asc"; + reg = <0x100B00 0x100>; + interrupt-parent = <&icu0>; + interrupts = <112 113 114>; + line = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&asc1_pins>; + clocks = <&clock_sys1 11>; + }; + + serial0: serial@100C00 { + compatible = "lantiq,asc"; + reg = <0x100C00 0x100>; + interrupt-parent = <&icu0>; + interrupts = <104 105 106>; + line = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&asc0_pins>; + clocks = <&clock_sys1 12>; + }; + + spi: spi@100D00 { + status = "disabled"; + compatible = "lantiq,falcon-spi", "lantiq,xrx100-spi", "lantiq,spi-lantiq-ssc"; + interrupts = <22 23 24 25>; + interrupt-names = "spi_tx", "spi_rx", "spi_err", "spi_frm"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x100D00 0x100>; + interrupt-parent = <&icu0>; + clocks = <&clock_sys1 13>; + base_cs = <1>; + num_cs = <2>; + }; + + gptc@100E00 { + compatible = "lantiq,gptc-falcon"; + reg = <0x100E00 0x100>; + }; + + i2c: i2c@200000 { + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,lantiq-i2c"; + reg = <0x200000 0x10000>; + interrupt-parent = <&icu0>; + interrupts = <18 19 20 21>; + gpios = <&gpio1 7 0 &gpio1 8 0>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c_pins>; + clocks = <&clock_sys1 14>; + }; + + gpio1: gpio@800100 { + compatible = "lantiq,falcon-gpio"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&icu0>; + interrupts = <45>; + reg = <0x800100 0x100>; + clocks = <&clock_sys1 16>; + }; + + gpio3: gpio@800200 { + compatible = "lantiq,falcon-gpio"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&icu0>; + interrupts = <47>; + reg = <0x800200 0x100>; + clocks = <&clock_sys1 17>; + }; + + gpio4: gpio@800300 { + compatible = "lantiq,falcon-gpio"; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&icu0>; + interrupts = <48>; + reg = <0x800300 0x100>; + clocks = <&clock_sys1 18>; + }; + + pad@800400 { + compatible = "lantiq,pad-falcon"; + reg = <0x800400 0x100>; + lantiq,bank = <1>; + clocks = <&clock_sys1 20>; + }; + + pad@800500 { + compatible = "lantiq,pad-falcon"; + reg = <0x800500 0x100>; + lantiq,bank = <3>; + clocks = <&clock_sys1 21>; + }; + + pad@800600 { + compatible = "lantiq,pad-falcon"; + reg = <0x800600 0x100>; + lantiq,bank = <4>; + clocks = <&clock_sys1 22>; + }; + + status@802000 { + compatible = "lantiq,status-falcon"; + reg = <0x802000 0x80>; + }; + + clock_sys1: clock-controller@F00000 { + compatible = "lantiq,sys1-falcon"; + reg = <0xF00000 0x100>; + #clock-cells = <1>; + }; + }; + + sbs0@1F000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + reg = <0x1F000000 0x400000>; + ranges = <0x0 0x1F000000 0x400000>; + + mpsmbx: mpsmbx@200000 { + reg = <0x200000 0x200>; + }; + }; + + sbs1@1F700000 { + + }; + + biu@1F800000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "lantiq,biu", "simple-bus"; + reg = <0x1F800000 0x800000>; + ranges = <0x0 0x1F800000 0x800000>; + + icu0: icu@80200 { + #interrupt-cells = <1>; + interrupt-controller; + compatible = "lantiq,icu"; + reg = <0x80200 0x28 + 0x80228 0x28 + 0x80250 0x28 + 0x80278 0x28 + 0x802a0 0x28>; + }; + + watchdog@803F0 { + compatible = "lantiq,wdt"; + reg = <0x803F0 0x10>; + clocks = <&io_clk>; /* currently no effect */ + }; + }; + + pinctrl { + compatible = "lantiq,pinctrl-falcon"; + pinctrl-names = "default"; + pinctrl-0 = <&state_default>; + + state_default: pinctrl0 { + /*ntr { + lantiq,groups = "ntr8k"; + lantiq,function = "ntr"; + };*/ + hrst { + lantiq,groups = "hrst"; + lantiq,function = "rst"; + }; + }; + + asc0_pins: asc0 { + asc0 { + lantiq,groups = "asc0"; + lantiq,function = "asc"; + }; + }; + asc1_pins: asc1 { + asc1 { + lantiq,groups = "asc1"; + lantiq,function = "asc"; + }; + }; + i2c_pins: i2c { + i2c { + lantiq,groups = "i2c"; + lantiq,function = "i2c"; + }; + }; + bootled_pins: bootled { + bootled { + lantiq,groups = "bootled"; + lantiq,function = "led"; + }; + }; + ntr_ntr8k: ntr8k { + ntr8k { + lantiq,groups = "ntr8k"; + lantiq,function = "ntr"; + }; + }; + ntr_pps: pps { + pps { + lantiq,groups = "pps"; + lantiq,function = "ntr"; + }; + }; + ntr_gpio: gpio { + gpio { + lantiq,pins = "io5"; + lantiq,mux = <1>; + lantiq,output = <0>; + }; + }; + slic_pins: slic { + slic { + lantiq,groups = "slic"; + lantiq,function = "slic"; + }; + }; + }; + + pinselect-ntr { + compatible = "lantiq,onu-ntr","lantiq,pinselect-ntr"; + pinctrl-names = "ntr8k", "pps", "gpio"; + pinctrl-0 = <&ntr_ntr8k>; + pinctrl-1 = <&ntr_pps>; + pinctrl-2 = <&ntr_gpio>; + }; + + pinselect-asc1 { + compatible = "lantiq,onu-asc1","lantiq,pinselect-asc1"; + pinctrl-names = "default", "asc1"; + pinctrl-0 = <&slic_pins>; + pinctrl-1 = <&asc1_pins>; + }; + +}; diff --git a/target/linux/lantiq/files/arch/mips/boot/dts/vr9.dtsi b/target/linux/lantiq/files/arch/mips/boot/dts/vr9.dtsi new file mode 100644 index 0000000000..6e8f0d1300 --- /dev/null +++ b/target/linux/lantiq/files/arch/mips/boot/dts/vr9.dtsi @@ -0,0 +1,341 @@ +#include + +/ { + #address-cells = <1>; + #size-cells = <1>; + compatible = "lantiq,xway", "lantiq,vr9"; + + aliases { + serial0 = &asc1; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + cpus { + cpu@0 { + compatible = "mips,mips34Kc"; + }; + }; + + memory@0 { + device_type = "memory"; + }; + + cputemp@0 { + compatible = "lantiq,cputemp"; + }; + + biu@1f800000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "lantiq,biu", "simple-bus"; + reg = <0x1f800000 0x800000>; + ranges = <0x0 0x1f800000 0x7fffff>; + + icu0: icu@80200 { + #interrupt-cells = <1>; + interrupt-controller; + compatible = "lantiq,icu"; + reg = <0x80200 0x28 + 0x80228 0x28 + 0x80250 0x28 + 0x80278 0x28 + 0x802a0 0x28>; + }; + + watchdog@803f0 { + compatible = "lantiq,xrx100-wdt", "lantiq,xrx100-wdt"; + reg = <0x803f0 0x10>; + + regmap = <&rcu0>; + }; + }; + + sram@1f000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "lantiq,sram", "simple-bus"; + reg = <0x1f000000 0x800000>; + ranges = <0x0 0x1f000000 0x7fffff>; + + eiu0: eiu@101000 { + #interrupt-cells = <1>; + interrupt-controller; + compatible = "lantiq,eiu-xway"; + reg = <0x101000 0x1000>; + interrupt-parent = <&icu0>; + lantiq,eiu-irqs = <166 135 66 40 41 42>; + }; + + pmu0: pmu@102000 { + compatible = "lantiq,pmu-xway"; + reg = <0x102000 0x1000>; + }; + + cgu0: cgu@103000 { + compatible = "lantiq,cgu-xway"; + reg = <0x103000 0x1000>; + }; + + dcdc@106a00 { + compatible = "lantiq,dcdc-xrx200"; + reg = <0x106a00 0x200>; + }; + + vmmc: vmmc@103000 { + status = "disabled"; + compatible = "lantiq,vmmc-xway"; + reg = <0x103000 0x400>; + interrupt-parent = <&icu0>; + interrupts = <150 151 152 153 154 155>; + }; + + rcu0: rcu@203000 { + compatible = "lantiq,xrx200-rcu", "simple-mfd", "syscon"; + reg = <0x203000 0x100>; + ranges = <0x0 0x203000 0x100>; + big-endian; + + gphy0: gphy@20 { + compatible = "lantiq,xrx200-gphy"; + reg = <0x20 0x4>; + + resets = <&reset0 31 30>, <&reset1 7 7>; + reset-names = "gphy", "gphy2"; + }; + + gphy1: gphy@68 { + compatible = "lantiq,xrx200-gphy"; + reg = <0x68 0x4>; + + resets = <&reset0 29 28>, <&reset1 6 6>; + reset-names = "gphy", "gphy2"; + }; + + reset0: reset-controller@10 { + compatible = "lantiq,xrx200-reset"; + reg = <0x10 4>, <0x14 4>; + + #reset-cells = <2>; + }; + + reset1: reset-controller@48 { + compatible = "lantiq,xrx200-reset"; + reg = <0x48 4>, <0x24 4>; + + #reset-cells = <2>; + }; + + usb_phy0: usb2-phy@18 { + compatible = "lantiq,xrx200-usb2-phy"; + reg = <0x18 4>, <0x38 4>; + status = "disabled"; + + resets = <&reset1 4 4>, <&reset0 4 4>; + reset-names = "phy", "ctrl"; + #phy-cells = <0>; + }; + + usb_phy1: usb2-phy@34 { + compatible = "lantiq,xrx200-usb2-phy"; + reg = <0x34 4>, <0x3c 4>; + status = "disabled"; + + resets = <&reset1 5 5>, <&reset0 4 4>; + reset-names = "phy", "ctrl"; + #phy-cells = <0>; + }; + + reboot@10 { + compatible = "syscon-reboot"; + reg = <0x10 4>; + + regmap = <&rcu0>; + offset = <0x10>; + mask = <0xe0000000>; + }; + }; + }; + + fpi@10000000 { + compatible = "lantiq,xrx200-fpi", "simple-bus"; + ranges = <0x0 0x10000000 0xf000000>; + reg = <0x1f400000 0x1000>, + <0x10000000 0xf000000>; + regmap = <&rcu0>; + offset-endianness = <0x4c>; + #address-cells = <1>; + #size-cells = <1>; + + localbus: localbus@0 { + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x0 0x3ffffff /* addrsel0 */ + 1 0 0x4000000 0x4000010>; /* addsel1 */ + compatible = "lantiq,localbus", "simple-bus"; + }; + + gptu@e100a00 { + compatible = "lantiq,gptu-xway"; + reg = <0xe100a00 0x100>; + interrupt-parent = <&icu0>; + interrupts = <126 127 128 129 130 131>; + }; + + usif: usif@da00000 { + compatible = "lantiq,usif"; + reg = <0xda00000 0x1000000>; + interrupt-parent = <&icu0>; + interrupts = <29 125 107 108 109 110>; + status = "disabled"; + }; + + spi: spi@e100800 { + compatible = "lantiq,xrx200-spi", "lantiq,xrx100-spi"; + reg = <0xe100800 0x100>; + interrupt-parent = <&icu0>; + interrupts = <22 23 24>; + interrupt-names = "spi_rx", "spi_tx", "spi_err", + "spi_frm"; + #address-cells = <1>; + #size-cells = <1>; + status = "disabled"; + }; + + gpio: pinmux@e100b10 { + compatible = "lantiq,xrx200-pinctrl"; + #gpio-cells = <2>; + gpio-controller; + reg = <0xe100b10 0xa0>; + }; + + stp: stp@e100bb0 { + status = "disabled"; + compatible = "lantiq,gpio-stp-xway"; + reg = <0xe100bb0 0x40>; + #gpio-cells = <2>; + gpio-controller; + + lantiq,shadow = <0xffffff>; + lantiq,groups = <0x7>; + lantiq,dsl = <0x0>; + lantiq,phy1 = <0x0>; + lantiq,phy2 = <0x0>; + }; + + asc1: serial@e100c00 { + compatible = "lantiq,asc"; + reg = <0xe100c00 0x400>; + interrupt-parent = <&icu0>; + interrupts = <112 113 114>; + }; + + deu@e103100 { + compatible = "lantiq,deu-xrx200"; + reg = <0xe103100 0xf00>; + }; + + dma0: dma@e104100 { + compatible = "lantiq,dma-xway"; + reg = <0xe104100 0x800>; + }; + + ebu0: ebu@e105300 { + compatible = "lantiq,ebu-xway"; + reg = <0xe105300 0x100>; + }; + + usb0: usb@e101000 { + status = "disabled"; + compatible = "lantiq,xrx200-usb"; + reg = <0xe101000 0x1000 + 0xe120000 0x3f000>; + interrupt-parent = <&icu0>; + interrupts = <62 91>; + dr_mode = "host"; + phys = <&usb_phy0>; + phy-names = "usb2-phy"; + }; + + usb1: usb@e106000 { + status = "disabled"; + compatible = "lantiq,xrx200-usb"; + reg = <0xe106000 0x1000>; + interrupt-parent = <&icu0>; + interrupts = <91>; + dr_mode = "host"; + phys = <&usb_phy1>; + phy-names = "usb2-phy"; + }; + + eth0: eth@e108000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "lantiq,xrx200-net"; + reg = < 0xe108000 0x3000 /* switch */ + 0xe10b100 0x70 /* mdio */ + 0xe10b1d8 0x30 /* mii */ + 0xe10b308 0x30 /* pmac */ + >; + interrupt-parent = <&icu0>; + interrupts = <75 73 72>; + resets = <&reset0 21 16>, <&reset0 8 8>; + reset-names = "switch", "ppe"; + lantiq,phys = <&gphy0>, <&gphy1>; + }; + + mei@e116000 { + compatible = "lantiq,mei-xrx200"; + reg = <0xe116000 0x9c>; + interrupt-parent = <&icu0>; + interrupts = <63>; + }; + + ppe@e234000 { + compatible = "lantiq,ppe-xrx200"; + interrupt-parent = <&icu0>; + interrupts = <96>; + resets = <&reset0 3 3>, <&reset0 11 11>, <&reset0 23 23>; + reset-names = "dsp", "dfe", "tc"; + }; + + pcie0: pcie@d900000 { + compatible = "lantiq,pcie-xrx200"; + + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + + interrupt-parent = <&icu0>; + interrupts = <161 144>; + + device_type = "pci"; + + gpio-reset = <&gpio 38 GPIO_ACTIVE_HIGH>; + }; + + pci0: pci@e105400 { + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + compatible = "lantiq,pci-xway"; + bus-range = <0x0 0x0>; + ranges = <0x2000000 0 0x8000000 0x8000000 0 0x2000000 /* pci memory */ + 0x1000000 0 0x00000000 0xae00000 0 0x200000>; /* io space */ + reg = <0x7000000 0x8000 /* config space */ + 0xe105400 0x400>; /* pci bridge */ + lantiq,bus-clock = <33333333>; + interrupt-map-mask = <0xf800 0x0 0x0 0x7>; + interrupt-map = <0x7000 0 0 1 &icu0 30 1>; /* slot 14, irq 30 */ + req-mask = <0x1>; /* GNT1 */ + }; + }; + + vdsl { + compatible = "lantiq,vdsl-vrx200"; + }; +}; diff --git a/target/linux/lantiq/patches-4.19/0001-MIPS-lantiq-add-pcie-driver.patch b/target/linux/lantiq/patches-4.19/0001-MIPS-lantiq-add-pcie-driver.patch new file mode 100644 index 0000000000..48dd111cca --- /dev/null +++ b/target/linux/lantiq/patches-4.19/0001-MIPS-lantiq-add-pcie-driver.patch @@ -0,0 +1,5520 @@ +From 6f933347d0b4ed02d9534f5fa07f7b99f13eeaa1 Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Thu, 7 Aug 2014 18:12:28 +0200 +Subject: [PATCH 01/36] MIPS: lantiq: add pcie driver + +Signed-off-by: John Crispin +--- + arch/mips/lantiq/Kconfig | 10 + + arch/mips/lantiq/xway/sysctrl.c | 2 + + arch/mips/pci/Makefile | 2 + + arch/mips/pci/fixup-lantiq-pcie.c | 82 +++ + arch/mips/pci/fixup-lantiq.c | 5 +- + arch/mips/pci/ifxmips_pci_common.h | 57 ++ + arch/mips/pci/ifxmips_pcie.c | 1099 ++++++++++++++++++++++++++++++ + arch/mips/pci/ifxmips_pcie.h | 135 ++++ + arch/mips/pci/ifxmips_pcie_ar10.h | 290 ++++++++ + arch/mips/pci/ifxmips_pcie_msi.c | 392 +++++++++++ + arch/mips/pci/ifxmips_pcie_phy.c | 478 +++++++++++++ + arch/mips/pci/ifxmips_pcie_pm.c | 176 +++++ + arch/mips/pci/ifxmips_pcie_pm.h | 36 + + arch/mips/pci/ifxmips_pcie_reg.h | 1001 +++++++++++++++++++++++++++ + arch/mips/pci/ifxmips_pcie_vr9.h | 271 ++++++++ + arch/mips/pci/pci.c | 25 + + arch/mips/pci/pcie-lantiq.h | 1305 ++++++++++++++++++++++++++++++++++++ + drivers/pci/pcie/aer/Kconfig | 2 +- + include/linux/pci.h | 2 + + include/linux/pci_ids.h | 6 + + 20 files changed, 5374 insertions(+), 2 deletions(-) + create mode 100644 arch/mips/pci/fixup-lantiq-pcie.c + create mode 100644 arch/mips/pci/ifxmips_pci_common.h + create mode 100644 arch/mips/pci/ifxmips_pcie.c + create mode 100644 arch/mips/pci/ifxmips_pcie.h + create mode 100644 arch/mips/pci/ifxmips_pcie_ar10.h + create mode 100644 arch/mips/pci/ifxmips_pcie_msi.c + create mode 100644 arch/mips/pci/ifxmips_pcie_phy.c + create mode 100644 arch/mips/pci/ifxmips_pcie_pm.c + create mode 100644 arch/mips/pci/ifxmips_pcie_pm.h + create mode 100644 arch/mips/pci/ifxmips_pcie_reg.h + create mode 100644 arch/mips/pci/ifxmips_pcie_vr9.h + create mode 100644 arch/mips/pci/pcie-lantiq.h + +--- a/arch/mips/lantiq/Kconfig ++++ b/arch/mips/lantiq/Kconfig +@@ -20,6 +20,7 @@ config SOC_XWAY + bool "XWAY" + select SOC_TYPE_XWAY + select HW_HAS_PCI ++ select ARCH_SUPPORTS_MSI + select MFD_SYSCON + select MFD_CORE + +@@ -52,6 +53,15 @@ config PCI_LANTIQ + bool "PCI Support" + depends on SOC_XWAY && PCI + ++config PCIE_LANTIQ ++ bool "PCIE Support" ++ depends on SOC_XWAY && PCI ++ ++config PCIE_LANTIQ_MSI ++ bool ++ depends on PCIE_LANTIQ && PCI_MSI ++ default y ++ + config XRX200_PHY_FW + bool "XRX200 PHY firmware loader" + depends on SOC_XWAY +--- a/arch/mips/pci/Makefile ++++ b/arch/mips/pci/Makefile +@@ -49,6 +49,8 @@ obj-$(CONFIG_PCI_LANTIQ) += pci-lantiq.o + obj-$(CONFIG_SOC_MT7620) += pci-mt7620.o + obj-$(CONFIG_SOC_RT288X) += pci-rt2880.o + obj-$(CONFIG_SOC_RT3883) += pci-rt3883.o ++obj-$(CONFIG_PCIE_LANTIQ) += ifxmips_pcie_phy.o ifxmips_pcie.o fixup-lantiq-pcie.o ++obj-$(CONFIG_PCIE_LANTIQ_MSI) += pcie-lantiq-msi.o + obj-$(CONFIG_TANBAC_TB0219) += fixup-tb0219.o + obj-$(CONFIG_TANBAC_TB0226) += fixup-tb0226.o + obj-$(CONFIG_TANBAC_TB0287) += fixup-tb0287.o +--- /dev/null ++++ b/arch/mips/pci/fixup-lantiq-pcie.c +@@ -0,0 +1,74 @@ ++/****************************************************************************** ++** ++** FILE NAME : ifxmips_fixup_pcie.c ++** PROJECT : IFX UEIP for VRX200 ++** MODULES : PCIe ++** ++** DATE : 02 Mar 2009 ++** AUTHOR : Lei Chuanhua ++** DESCRIPTION : PCIe Root Complex Driver ++** COPYRIGHT : Copyright (c) 2009 ++** Infineon Technologies AG ++** Am Campeon 1-12, 85579 Neubiberg, Germany ++** ++** This program is free software; you can redistribute it and/or modify ++** it under the terms of the GNU General Public License as published by ++** the Free Software Foundation; either version 2 of the License, or ++** (at your option) any later version. ++** HISTORY ++** $Version $Date $Author $Comment ++** 0.0.1 17 Mar,2009 Lei Chuanhua Initial version ++*******************************************************************************/ ++/*! ++ \file ifxmips_fixup_pcie.c ++ \ingroup IFX_PCIE ++ \brief PCIe Fixup functions source file ++*/ ++#include ++#include ++#include ++ ++#include ++ ++#include "pcie-lantiq.h" ++ ++static void ++ifx_pcie_fixup_resource(struct pci_dev *dev) ++{ ++ u32 reg; ++ ++ IFX_PCIE_PRINT(PCIE_MSG_FIXUP, "%s dev %s: enter\n", __func__, pci_name(dev)); ++ ++ printk("%s: fixup host controller %s (%04x:%04x)\n", ++ __func__, pci_name(dev), dev->vendor, dev->device); ++ ++ /* Setup COMMAND register */ ++ reg = PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER /* | ++ PCI_COMMAND_INTX_DISABLE */| PCI_COMMAND_SERR; ++ pci_write_config_word(dev, PCI_COMMAND, reg); ++ IFX_PCIE_PRINT(PCIE_MSG_FIXUP, "%s dev %s: exit\n", __func__, pci_name(dev)); ++} ++DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INFINEON, PCI_DEVICE_ID_INFINEON_PCIE, ifx_pcie_fixup_resource); ++DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_LANTIQ, PCI_VENDOR_ID_LANTIQ, ifx_pcie_fixup_resource); ++ ++static void ++ifx_pcie_rc_class_early_fixup(struct pci_dev *dev) ++{ ++ IFX_PCIE_PRINT(PCIE_MSG_FIXUP, "%s dev %s: enter\n", __func__, pci_name(dev)); ++ ++ if (dev->devfn == PCI_DEVFN(0, 0) && ++ (dev->class >> 8) == PCI_CLASS_BRIDGE_HOST) { ++ ++ dev->class = (PCI_CLASS_BRIDGE_PCI << 8) | (dev->class & 0xff); ++ ++ printk(KERN_INFO "%s: fixed pcie host bridge to pci-pci bridge\n", __func__); ++ } ++ IFX_PCIE_PRINT(PCIE_MSG_FIXUP, "%s dev %s: exit\n", __func__, pci_name(dev)); ++ mdelay(10); ++} ++ ++DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INFINEON, PCI_DEVICE_ID_INFINEON_PCIE, ++ ifx_pcie_rc_class_early_fixup); ++ ++DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_LANTIQ, PCI_DEVICE_ID_LANTIQ_PCIE, ++ ifx_pcie_rc_class_early_fixup); +--- a/arch/mips/pci/fixup-lantiq.c ++++ b/arch/mips/pci/fixup-lantiq.c +@@ -8,12 +8,18 @@ + + #include + #include ++#include "ifxmips_pci_common.h" + + int (*ltq_pci_plat_arch_init)(struct pci_dev *dev) = NULL; + int (*ltq_pci_plat_dev_init)(struct pci_dev *dev) = NULL; + + int pcibios_plat_dev_init(struct pci_dev *dev) + { ++#ifdef CONFIG_PCIE_LANTIQ ++ if (pci_find_capability(dev, PCI_CAP_ID_EXP)) ++ ifx_pcie_bios_plat_dev_init(dev); ++#endif ++ + if (ltq_pci_plat_arch_init) + return ltq_pci_plat_arch_init(dev); + +@@ -25,5 +31,10 @@ int pcibios_plat_dev_init(struct pci_dev + + int pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) + { ++#ifdef CONFIG_PCIE_LANTIQ ++ if (pci_find_capability(dev, PCI_CAP_ID_EXP)) ++ return ifx_pcie_bios_map_irq(dev, slot, pin); ++#endif ++ + return of_irq_parse_and_map_pci(dev, slot, pin); + } +--- /dev/null ++++ b/arch/mips/pci/ifxmips_pci_common.h +@@ -0,0 +1,57 @@ ++/****************************************************************************** ++** ++** FILE NAME : ifxmips_pci_common.h ++** PROJECT : IFX UEIP ++** MODULES : PCI subsystem ++** ++** DATE : 30 June 2009 ++** AUTHOR : Lei Chuanhua ++** DESCRIPTION : PCIe Root Complex Driver ++** COPYRIGHT : Copyright (c) 2009 ++** Infineon Technologies AG ++** Am Campeon 1-12, 85579 Neubiberg, Germany ++** ++** This program is free software; you can redistribute it and/or modify ++** it under the terms of the GNU General Public License as published by ++** the Free Software Foundation; either version 2 of the License, or ++** (at your option) any later version. ++** HISTORY ++** $Version $Date $Author $Comment ++** 0.0.1 30 June,2009 Lei Chuanhua Initial version ++*******************************************************************************/ ++ ++#ifndef IFXMIPS_PCI_COMMON_H ++#define IFXMIPS_PCI_COMMON_H ++#include ++/*! ++ \defgroup IFX_PCI_COM IFX PCI/PCIe common parts for OS integration ++ \brief PCI/PCIe common parts ++*/ ++ ++/*! ++ \defgroup IFX_PCI_COM_OS OS APIs ++ \ingroup IFX_PCI_COM ++ \brief PCI/PCIe bus driver OS interface functions ++*/ ++/*! ++ \file ifxmips_pci_common.h ++ \ingroup IFX_PCI_COM ++ \brief PCI/PCIe bus driver common OS header file ++*/ ++#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,24) ++#define IFX_PCI_CONST ++#else ++#define IFX_PCI_CONST const ++#endif ++#ifdef CONFIG_IFX_PCI ++extern int ifx_pci_bios_map_irq(IFX_PCI_CONST struct pci_dev *dev, u8 slot, u8 pin); ++extern int ifx_pci_bios_plat_dev_init(struct pci_dev *dev); ++#endif /* COFNIG_IFX_PCI */ ++ ++#ifdef CONFIG_PCIE_LANTIQ ++extern int ifx_pcie_bios_map_irq(IFX_PCI_CONST struct pci_dev *dev, u8 slot, u8 pin); ++extern int ifx_pcie_bios_plat_dev_init(struct pci_dev *dev); ++#endif ++ ++#endif /* IFXMIPS_PCI_COMMON_H */ ++ +--- /dev/null ++++ b/arch/mips/pci/ifxmips_pcie.c +@@ -0,0 +1,1092 @@ ++/* ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms of the GNU General Public License version 2 as published ++ * by the Free Software Foundation. ++ * ++ * Copyright (C) 2009 Lei Chuanhua ++ * Copyright (C) 2013 John Crispin ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include "ifxmips_pcie.h" ++#include "ifxmips_pcie_reg.h" ++ ++/* Enable 32bit io due to its mem mapped io nature */ ++#define IFX_PCIE_ERROR_INT ++#define IFX_PCIE_IO_32BIT ++ ++#define IFX_PCIE_IR (INT_NUM_IM4_IRL0 + 25) ++#define IFX_PCIE_INTA (INT_NUM_IM4_IRL0 + 8) ++#define IFX_PCIE_INTB (INT_NUM_IM4_IRL0 + 9) ++#define IFX_PCIE_INTC (INT_NUM_IM4_IRL0 + 10) ++#define IFX_PCIE_INTD (INT_NUM_IM4_IRL0 + 11) ++#define MS(_v, _f) (((_v) & (_f)) >> _f##_S) ++#define SM(_v, _f) (((_v) << _f##_S) & (_f)) ++#define IFX_REG_SET_BIT(_f, _r) \ ++ IFX_REG_W32((IFX_REG_R32((_r)) &~ (_f)) | (_f), (_r)) ++ ++#define IFX_PCIE_LTSSM_ENABLE_TIMEOUT 10 ++ ++static DEFINE_SPINLOCK(ifx_pcie_lock); ++ ++u32 g_pcie_debug_flag = PCIE_MSG_ANY & (~PCIE_MSG_CFG); ++ ++static ifx_pcie_irq_t pcie_irqs[IFX_PCIE_CORE_NR] = { ++ { ++ .ir_irq = { ++ .irq = IFX_PCIE_IR, ++ .name = "ifx_pcie_rc0", ++ }, ++ ++ .legacy_irq = { ++ { ++ .irq_bit = PCIE_IRN_INTA, ++ .irq = IFX_PCIE_INTA, ++ }, ++ { ++ .irq_bit = PCIE_IRN_INTB, ++ .irq = IFX_PCIE_INTB, ++ }, ++ { ++ .irq_bit = PCIE_IRN_INTC, ++ .irq = IFX_PCIE_INTC, ++ }, ++ { ++ .irq_bit = PCIE_IRN_INTD, ++ .irq = IFX_PCIE_INTD, ++ }, ++ }, ++ }, ++ ++}; ++ ++void ifx_pcie_debug(const char *fmt, ...) ++{ ++ static char buf[256] = {0}; /* XXX */ ++ va_list ap; ++ ++ va_start(ap, fmt); ++ vsnprintf(buf, sizeof(buf), fmt, ap); ++ va_end(ap); ++ ++ printk("%s", buf); ++} ++ ++ ++static inline int pcie_ltssm_enable(int pcie_port) ++{ ++ int i; ++ ++ /* Enable LTSSM */ ++ IFX_REG_W32(PCIE_RC_CCR_LTSSM_ENABLE, PCIE_RC_CCR(pcie_port)); ++ ++ /* Wait for the link to come up */ ++ for (i = 0; i < IFX_PCIE_LTSSM_ENABLE_TIMEOUT; i++) { ++ if (!(IFX_REG_R32(PCIE_LCTLSTS(pcie_port)) & PCIE_LCTLSTS_RETRAIN_PENDING)) ++ return 0; ++ udelay(10); ++ } ++ ++ printk("%s link timeout!!!!!\n", __func__); ++ return -1; ++} ++ ++static inline void pcie_status_register_clear(int pcie_port) ++{ ++ IFX_REG_W32(0, PCIE_RC_DR(pcie_port)); ++ IFX_REG_W32(0, PCIE_PCICMDSTS(pcie_port)); ++ IFX_REG_W32(0, PCIE_DCTLSTS(pcie_port)); ++ IFX_REG_W32(0, PCIE_LCTLSTS(pcie_port)); ++ IFX_REG_W32(0, PCIE_SLCTLSTS(pcie_port)); ++ IFX_REG_W32(0, PCIE_RSTS(pcie_port)); ++ IFX_REG_W32(0, PCIE_UES_R(pcie_port)); ++ IFX_REG_W32(0, PCIE_UEMR(pcie_port)); ++ IFX_REG_W32(0, PCIE_UESR(pcie_port)); ++ IFX_REG_W32(0, PCIE_CESR(pcie_port)); ++ IFX_REG_W32(0, PCIE_CEMR(pcie_port)); ++ IFX_REG_W32(0, PCIE_RESR(pcie_port)); ++ IFX_REG_W32(0, PCIE_PVCCRSR(pcie_port)); ++ IFX_REG_W32(0, PCIE_VC0_RSR0(pcie_port)); ++ IFX_REG_W32(0, PCIE_TPFCS(pcie_port)); ++ IFX_REG_W32(0, PCIE_TNPFCS(pcie_port)); ++ IFX_REG_W32(0, PCIE_TCFCS(pcie_port)); ++ IFX_REG_W32(0, PCIE_QSR(pcie_port)); ++ IFX_REG_W32(0, PCIE_IOBLSECS(pcie_port)); ++} ++ ++static inline int ifx_pcie_link_up(int pcie_port) ++{ ++ return (IFX_REG_R32(PCIE_PHY_SR(pcie_port)) & PCIE_PHY_SR_PHY_LINK_UP) ? 1 : 0; ++} ++ ++ ++static inline void pcie_mem_io_setup(int pcie_port) ++{ ++ u32 reg; ++ /* ++ * BAR[0:1] readonly register ++ * RC contains only minimal BARs for packets mapped to this device ++ * Mem/IO filters defines a range of memory occupied by memory mapped IO devices that ++ * reside on the downstream side fo the bridge. ++ */ ++ reg = SM((PCIE_MEM_PHY_PORT_TO_END(pcie_port) >> 20), PCIE_MBML_MEM_LIMIT_ADDR) ++ | SM((PCIE_MEM_PHY_PORT_TO_BASE(pcie_port) >> 20), PCIE_MBML_MEM_BASE_ADDR); ++ ++ IFX_REG_W32(reg, PCIE_MBML(pcie_port)); ++ ++ ++#ifdef IFX_PCIE_PREFETCH_MEM_64BIT ++ reg = SM((PCIE_MEM_PHY_PORT_TO_END(pcie_port) >> 20), PCIE_PMBL_END_ADDR) ++ | SM((PCIE_MEM_PHY_PORT_TO_BASE(pcie_port) >> 20), PCIE_PMBL_UPPER_12BIT) ++ | PCIE_PMBL_64BIT_ADDR; ++ IFX_REG_W32(reg, PCIE_PMBL(pcie_port)); ++ ++ /* Must configure upper 32bit */ ++ IFX_REG_W32(0, PCIE_PMBU32(pcie_port)); ++ IFX_REG_W32(0, PCIE_PMLU32(pcie_port)); ++#else ++ /* PCIe_PBML, same as MBML */ ++ IFX_REG_W32(IFX_REG_R32(PCIE_MBML(pcie_port)), PCIE_PMBL(pcie_port)); ++#endif ++ ++ /* IO Address Range */ ++ reg = SM((PCIE_IO_PHY_PORT_TO_END(pcie_port) >> 12), PCIE_IOBLSECS_IO_LIMIT_ADDR) ++ | SM((PCIE_IO_PHY_PORT_TO_BASE(pcie_port) >> 12), PCIE_IOBLSECS_IO_BASE_ADDR); ++#ifdef IFX_PCIE_IO_32BIT ++ reg |= PCIE_IOBLSECS_32BIT_IO_ADDR; ++#endif /* IFX_PCIE_IO_32BIT */ ++ IFX_REG_W32(reg, PCIE_IOBLSECS(pcie_port)); ++ ++#ifdef IFX_PCIE_IO_32BIT ++ reg = SM((PCIE_IO_PHY_PORT_TO_END(pcie_port) >> 16), PCIE_IO_BANDL_UPPER_16BIT_IO_LIMIT) ++ | SM((PCIE_IO_PHY_PORT_TO_BASE(pcie_port) >> 16), PCIE_IO_BANDL_UPPER_16BIT_IO_BASE); ++ IFX_REG_W32(reg, PCIE_IO_BANDL(pcie_port)); ++ ++#endif /* IFX_PCIE_IO_32BIT */ ++} ++ ++static inline void ++pcie_device_setup(int pcie_port) ++{ ++ u32 reg; ++ ++ /* Device capability register, set up Maximum payload size */ ++ reg = IFX_REG_R32(PCIE_DCAP(pcie_port)); ++ reg |= PCIE_DCAP_ROLE_BASE_ERR_REPORT; ++ reg |= SM(PCIE_MAX_PAYLOAD_128, PCIE_DCAP_MAX_PAYLOAD_SIZE); ++ ++ /* Only available for EP */ ++ reg &= ~(PCIE_DCAP_EP_L0S_LATENCY | PCIE_DCAP_EP_L1_LATENCY); ++ IFX_REG_W32(reg, PCIE_DCAP(pcie_port)); ++ ++ /* Device control and status register */ ++ /* Set Maximum Read Request size for the device as a Requestor */ ++ reg = IFX_REG_R32(PCIE_DCTLSTS(pcie_port)); ++ ++ /* ++ * Request size can be larger than the MPS used, but the completions returned ++ * for the read will be bounded by the MPS size. ++ * In our system, Max request size depends on AHB burst size. It is 64 bytes. ++ * but we set it as 128 as minimum one. ++ */ ++ reg |= SM(PCIE_MAX_PAYLOAD_128, PCIE_DCTLSTS_MAX_READ_SIZE) ++ | SM(PCIE_MAX_PAYLOAD_128, PCIE_DCTLSTS_MAX_PAYLOAD_SIZE); ++ ++ /* Enable relaxed ordering, no snoop, and all kinds of errors */ ++ reg |= PCIE_DCTLSTS_RELAXED_ORDERING_EN | PCIE_DCTLSTS_ERR_EN | PCIE_DCTLSTS_NO_SNOOP_EN; ++ ++ IFX_REG_W32(reg, PCIE_DCTLSTS(pcie_port)); ++} ++ ++static inline void ++pcie_link_setup(int pcie_port) ++{ ++ u32 reg; ++ ++ /* ++ * XXX, Link capability register, bit 18 for EP CLKREQ# dynamic clock management for L1, L2/3 CPM ++ * L0s is reported during link training via TS1 order set by N_FTS ++ */ ++ reg = IFX_REG_R32(PCIE_LCAP(pcie_port)); ++ reg &= ~PCIE_LCAP_L0S_EIXT_LATENCY; ++ reg |= SM(3, PCIE_LCAP_L0S_EIXT_LATENCY); ++ IFX_REG_W32(reg, PCIE_LCAP(pcie_port)); ++ ++ /* Link control and status register */ ++ reg = IFX_REG_R32(PCIE_LCTLSTS(pcie_port)); ++ ++ /* Link Enable, ASPM enabled */ ++ reg &= ~PCIE_LCTLSTS_LINK_DISABLE; ++ ++#ifdef CONFIG_PCIEASPM ++ /* ++ * We use the same physical reference clock that the platform provides on the connector ++ * It paved the way for ASPM to calculate the new exit Latency ++ */ ++ reg |= PCIE_LCTLSTS_SLOT_CLK_CFG; ++ reg |= PCIE_LCTLSTS_COM_CLK_CFG; ++ /* ++ * We should disable ASPM by default except that we have dedicated power management support ++ * Enable ASPM will cause the system hangup/instability, performance degration ++ */ ++ reg |= PCIE_LCTLSTS_ASPM_ENABLE; ++#else ++ reg &= ~PCIE_LCTLSTS_ASPM_ENABLE; ++#endif /* CONFIG_PCIEASPM */ ++ ++ /* ++ * The maximum size of any completion with data packet is bounded by the MPS setting ++ * in device control register ++ */ ++ ++ /* RCB may cause multiple split transactions, two options available, we use 64 byte RCB */ ++ reg &= ~ PCIE_LCTLSTS_RCB128; ++ ++ IFX_REG_W32(reg, PCIE_LCTLSTS(pcie_port)); ++} ++ ++static inline void pcie_error_setup(int pcie_port) ++{ ++ u32 reg; ++ ++ /* ++ * Forward ERR_COR, ERR_NONFATAL, ERR_FATAL to the backbone ++ * Poisoned write TLPs and completions indicating poisoned TLPs will set the PCIe_PCICMDSTS.MDPE ++ */ ++ reg = IFX_REG_R32(PCIE_INTRBCTRL(pcie_port)); ++ reg |= PCIE_INTRBCTRL_SERR_ENABLE | PCIE_INTRBCTRL_PARITY_ERR_RESP_ENABLE; ++ ++ IFX_REG_W32(reg, PCIE_INTRBCTRL(pcie_port)); ++ ++ /* Uncorrectable Error Mask Register, Unmask all bits in PCIE_UESR */ ++ reg = IFX_REG_R32(PCIE_UEMR(pcie_port)); ++ reg &= ~PCIE_ALL_UNCORRECTABLE_ERR; ++ IFX_REG_W32(reg, PCIE_UEMR(pcie_port)); ++ ++ /* Uncorrectable Error Severity Register, ALL errors are FATAL */ ++ IFX_REG_W32(PCIE_ALL_UNCORRECTABLE_ERR, PCIE_UESR(pcie_port)); ++ ++ /* Correctable Error Mask Register, unmask all bits */ ++ reg = IFX_REG_R32(PCIE_CEMR(pcie_port)); ++ reg &= ~PCIE_CORRECTABLE_ERR; ++ IFX_REG_W32(reg, PCIE_CEMR(pcie_port)); ++ ++ /* Advanced Error Capabilities and Control Registr */ ++ reg = IFX_REG_R32(PCIE_AECCR(pcie_port)); ++ reg |= PCIE_AECCR_ECRC_CHECK_EN | PCIE_AECCR_ECRC_GEN_EN; ++ IFX_REG_W32(reg, PCIE_AECCR(pcie_port)); ++ ++ /* Root Error Command Register, Report all types of errors */ ++ reg = IFX_REG_R32(PCIE_RECR(pcie_port)); ++ reg |= PCIE_RECR_ERR_REPORT_EN; ++ IFX_REG_W32(reg, PCIE_RECR(pcie_port)); ++ ++ /* Clear the Root status register */ ++ reg = IFX_REG_R32(PCIE_RESR(pcie_port)); ++ IFX_REG_W32(reg, PCIE_RESR(pcie_port)); ++} ++ ++static inline void pcie_port_logic_setup(int pcie_port) ++{ ++ u32 reg; ++ ++ /* FTS number, default 12, increase to 63, may increase time from/to L0s to L0 */ ++ reg = IFX_REG_R32(PCIE_AFR(pcie_port)); ++ reg &= ~(PCIE_AFR_FTS_NUM | PCIE_AFR_COM_FTS_NUM); ++ reg |= SM(PCIE_AFR_FTS_NUM_DEFAULT, PCIE_AFR_FTS_NUM) ++ | SM(PCIE_AFR_FTS_NUM_DEFAULT, PCIE_AFR_COM_FTS_NUM); ++ /* L0s and L1 entry latency */ ++ reg &= ~(PCIE_AFR_L0S_ENTRY_LATENCY | PCIE_AFR_L1_ENTRY_LATENCY); ++ reg |= SM(PCIE_AFR_L0S_ENTRY_LATENCY_DEFAULT, PCIE_AFR_L0S_ENTRY_LATENCY) ++ | SM(PCIE_AFR_L1_ENTRY_LATENCY_DEFAULT, PCIE_AFR_L1_ENTRY_LATENCY); ++ IFX_REG_W32(reg, PCIE_AFR(pcie_port)); ++ ++ ++ /* Port Link Control Register */ ++ reg = IFX_REG_R32(PCIE_PLCR(pcie_port)); ++ reg |= PCIE_PLCR_DLL_LINK_EN; /* Enable the DLL link */ ++ IFX_REG_W32(reg, PCIE_PLCR(pcie_port)); ++ ++ /* Lane Skew Register */ ++ reg = IFX_REG_R32(PCIE_LSR(pcie_port)); ++ /* Enable ACK/NACK and FC */ ++ reg &= ~(PCIE_LSR_ACKNAK_DISABLE | PCIE_LSR_FC_DISABLE); ++ IFX_REG_W32(reg, PCIE_LSR(pcie_port)); ++ ++ /* Symbol Timer Register and Filter Mask Register 1 */ ++ reg = IFX_REG_R32(PCIE_STRFMR(pcie_port)); ++ ++ /* Default SKP interval is very accurate already, 5us */ ++ /* Enable IO/CFG transaction */ ++ reg |= PCIE_STRFMR_RX_CFG_TRANS_ENABLE | PCIE_STRFMR_RX_IO_TRANS_ENABLE; ++ /* Disable FC WDT */ ++ reg &= ~PCIE_STRFMR_FC_WDT_DISABLE; ++ IFX_REG_W32(reg, PCIE_STRFMR(pcie_port)); ++ ++ /* Filter Masker Register 2 */ ++ reg = IFX_REG_R32(PCIE_FMR2(pcie_port)); ++ reg |= PCIE_FMR2_VENDOR_MSG1_PASSED_TO_TRGT1 | PCIE_FMR2_VENDOR_MSG0_PASSED_TO_TRGT1; ++ IFX_REG_W32(reg, PCIE_FMR2(pcie_port)); ++ ++ /* VC0 Completion Receive Queue Control Register */ ++ reg = IFX_REG_R32(PCIE_VC0_CRQCR(pcie_port)); ++ reg &= ~PCIE_VC0_CRQCR_CPL_TLP_QUEUE_MODE; ++ reg |= SM(PCIE_VC0_TLP_QUEUE_MODE_BYPASS, PCIE_VC0_CRQCR_CPL_TLP_QUEUE_MODE); ++ IFX_REG_W32(reg, PCIE_VC0_CRQCR(pcie_port)); ++} ++ ++static inline void pcie_rc_cfg_reg_setup(int pcie_port) ++{ ++ u32 reg; ++ ++ /* Disable LTSSM */ ++ IFX_REG_W32(0, PCIE_RC_CCR(pcie_port)); /* Disable LTSSM */ ++ ++ pcie_mem_io_setup(pcie_port); ++ ++ /* XXX, MSI stuff should only apply to EP */ ++ /* MSI Capability: Only enable 32-bit addresses */ ++ reg = IFX_REG_R32(PCIE_MCAPR(pcie_port)); ++ reg &= ~PCIE_MCAPR_ADDR64_CAP; ++ ++ reg |= PCIE_MCAPR_MSI_ENABLE; ++ ++ /* Disable multiple message */ ++ reg &= ~(PCIE_MCAPR_MULTI_MSG_CAP | PCIE_MCAPR_MULTI_MSG_ENABLE); ++ IFX_REG_W32(reg, PCIE_MCAPR(pcie_port)); ++ ++ ++ /* Enable PME, Soft reset enabled */ ++ reg = IFX_REG_R32(PCIE_PM_CSR(pcie_port)); ++ reg |= PCIE_PM_CSR_PME_ENABLE | PCIE_PM_CSR_SW_RST; ++ IFX_REG_W32(reg, PCIE_PM_CSR(pcie_port)); ++ ++ /* setup the bus */ ++ reg = SM(0, PCIE_BNR_PRIMARY_BUS_NUM) | SM(1, PCIE_PNR_SECONDARY_BUS_NUM) | SM(0xFF, PCIE_PNR_SUB_BUS_NUM); ++ IFX_REG_W32(reg, PCIE_BNR(pcie_port)); ++ ++ ++ pcie_device_setup(pcie_port); ++ pcie_link_setup(pcie_port); ++ pcie_error_setup(pcie_port); ++ ++ /* Root control and capabilities register */ ++ reg = IFX_REG_R32(PCIE_RCTLCAP(pcie_port)); ++ reg |= PCIE_RCTLCAP_SERR_ENABLE | PCIE_RCTLCAP_PME_INT_EN; ++ IFX_REG_W32(reg, PCIE_RCTLCAP(pcie_port)); ++ ++ /* Port VC Capability Register 2 */ ++ reg = IFX_REG_R32(PCIE_PVC2(pcie_port)); ++ reg &= ~PCIE_PVC2_VC_ARB_WRR; ++ reg |= PCIE_PVC2_VC_ARB_16P_FIXED_WRR; ++ IFX_REG_W32(reg, PCIE_PVC2(pcie_port)); ++ ++ /* VC0 Resource Capability Register */ ++ reg = IFX_REG_R32(PCIE_VC0_RC(pcie_port)); ++ reg &= ~PCIE_VC0_RC_REJECT_SNOOP; ++ IFX_REG_W32(reg, PCIE_VC0_RC(pcie_port)); ++ ++ pcie_port_logic_setup(pcie_port); ++} ++ ++static int ifx_pcie_wait_phy_link_up(int pcie_port) ++{ ++#define IFX_PCIE_PHY_LINK_UP_TIMEOUT 1000 /* XXX, tunable */ ++ int i; ++ ++ /* Wait for PHY link is up */ ++ for (i = 0; i < IFX_PCIE_PHY_LINK_UP_TIMEOUT; i++) { ++ if (ifx_pcie_link_up(pcie_port)) { ++ break; ++ } ++ udelay(100); ++ } ++ if (i >= IFX_PCIE_PHY_LINK_UP_TIMEOUT) { ++ printk(KERN_ERR "%s timeout\n", __func__); ++ return -1; ++ } ++ ++ /* Check data link up or not */ ++ if (!(IFX_REG_R32(PCIE_RC_DR(pcie_port)) & PCIE_RC_DR_DLL_UP)) { ++ printk(KERN_ERR "%s DLL link is still down\n", __func__); ++ return -1; ++ } ++ ++ /* Check Data link active or not */ ++ if (!(IFX_REG_R32(PCIE_LCTLSTS(pcie_port)) & PCIE_LCTLSTS_DLL_ACTIVE)) { ++ printk(KERN_ERR "%s DLL is not active\n", __func__); ++ return -1; ++ } ++ return 0; ++} ++ ++static inline int pcie_app_loigc_setup(int pcie_port) ++{ ++ /* supress ahb bus errrors */ ++ IFX_REG_W32(PCIE_AHB_CTRL_BUS_ERROR_SUPPRESS, PCIE_AHB_CTRL(pcie_port)); ++ ++ /* Pull PCIe EP out of reset */ ++ pcie_device_rst_deassert(pcie_port); ++ ++ /* Start LTSSM training between RC and EP */ ++ pcie_ltssm_enable(pcie_port); ++ ++ /* Check PHY status after enabling LTSSM */ ++ if (ifx_pcie_wait_phy_link_up(pcie_port) != 0) ++ return -1; ++ ++ return 0; ++} ++ ++/* ++ * The numbers below are directly from the PCIe spec table 3-4/5. ++ */ ++static inline void pcie_replay_time_update(int pcie_port) ++{ ++ u32 reg; ++ int nlw; ++ int rtl; ++ ++ reg = IFX_REG_R32(PCIE_LCTLSTS(pcie_port)); ++ ++ nlw = MS(reg, PCIE_LCTLSTS_NEGOTIATED_LINK_WIDTH); ++ switch (nlw) { ++ case PCIE_MAX_LENGTH_WIDTH_X1: ++ rtl = 1677; ++ break; ++ case PCIE_MAX_LENGTH_WIDTH_X2: ++ rtl = 867; ++ break; ++ case PCIE_MAX_LENGTH_WIDTH_X4: ++ rtl = 462; ++ break; ++ case PCIE_MAX_LENGTH_WIDTH_X8: ++ rtl = 258; ++ break; ++ default: ++ rtl = 1677; ++ break; ++ } ++ reg = IFX_REG_R32(PCIE_ALTRT(pcie_port)); ++ reg &= ~PCIE_ALTRT_REPLAY_TIME_LIMIT; ++ reg |= SM(rtl, PCIE_ALTRT_REPLAY_TIME_LIMIT); ++ IFX_REG_W32(reg, PCIE_ALTRT(pcie_port)); ++} ++ ++/* ++ * Table 359 Enhanced Configuration Address Mapping1) ++ * 1) This table is defined in Table 7-1, page 341, PCI Express Base Specification v1.1 ++ * Memory Address PCI Express Configuration Space ++ * A[(20+n-1):20] Bus Number 1 < n < 8 ++ * A[19:15] Device Number ++ * A[14:12] Function Number ++ * A[11:8] Extended Register Number ++ * A[7:2] Register Number ++ * A[1:0] Along with size of the access, used to generate Byte Enables ++ * For VR9, only the address bits [22:0] are mapped to the configuration space: ++ * . Address bits [22:20] select the target bus (1-of-8)1) ++ * . Address bits [19:15] select the target device (1-of-32) on the bus ++ * . Address bits [14:12] select the target function (1-of-8) within the device. ++ * . Address bits [11:2] selects the target dword (1-of-1024) within the selected function.s configuration space ++ * . Address bits [1:0] define the start byte location within the selected dword. ++ */ ++static inline u32 pcie_bus_addr(u8 bus_num, u16 devfn, int where) ++{ ++ u32 addr; ++ u8 bus; ++ ++ if (!bus_num) { ++ /* type 0 */ ++ addr = ((PCI_SLOT(devfn) & 0x1F) << 15) | ((PCI_FUNC(devfn) & 0x7) << 12) | ((where & 0xFFF)& ~3); ++ } else { ++ bus = bus_num; ++ /* type 1, only support 8 buses */ ++ addr = ((bus & 0x7) << 20) | ((PCI_SLOT(devfn) & 0x1F) << 15) | ++ ((PCI_FUNC(devfn) & 0x7) << 12) | ((where & 0xFFF) & ~3); ++ } ++ return addr; ++} ++ ++static int pcie_valid_config(int pcie_port, int bus, int dev) ++{ ++ /* RC itself */ ++ if ((bus == 0) && (dev == 0)) { ++ return 1; ++ } ++ ++ /* No physical link */ ++ if (!ifx_pcie_link_up(pcie_port)) { ++ return 0; ++ } ++ ++ /* Bus zero only has RC itself ++ * XXX, check if EP will be integrated ++ */ ++ if ((bus == 0) && (dev != 0)) { ++ return 0; ++ } ++ ++ /* Maximum 8 buses supported for VRX */ ++ if (bus > 9) { ++ return 0; ++ } ++ ++ /* ++ * PCIe is PtP link, one bus only supports only one device ++ * except bus zero and PCIe switch which is virtual bus device ++ * The following two conditions really depends on the system design ++ * and attached the device. ++ * XXX, how about more new switch ++ */ ++ if ((bus == 1) && (dev != 0)) { ++ return 0; ++ } ++ ++ if ((bus >= 3) && (dev != 0)) { ++ return 0; ++ } ++ return 1; ++} ++ ++static inline u32 ifx_pcie_cfg_rd(int pcie_port, u32 reg) ++{ ++ return IFX_REG_R32((volatile u32 *)(PCIE_CFG_PORT_TO_BASE(pcie_port) + reg)); ++} ++ ++static inline void ifx_pcie_cfg_wr(int pcie_port, unsigned int reg, u32 val) ++{ ++ IFX_REG_W32( val, (volatile u32 *)(PCIE_CFG_PORT_TO_BASE(pcie_port) + reg)); ++} ++ ++static inline u32 ifx_pcie_rc_cfg_rd(int pcie_port, u32 reg) ++{ ++ return IFX_REG_R32((volatile u32 *)(PCIE_RC_PORT_TO_BASE(pcie_port) + reg)); ++} ++ ++static inline void ifx_pcie_rc_cfg_wr(int pcie_port, unsigned int reg, u32 val) ++{ ++ IFX_REG_W32(val, (volatile u32 *)(PCIE_RC_PORT_TO_BASE(pcie_port) + reg)); ++} ++ ++u32 ifx_pcie_bus_enum_read_hack(int where, u32 value) ++{ ++ u32 tvalue = value; ++ ++ if (where == PCI_PRIMARY_BUS) { ++ u8 primary, secondary, subordinate; ++ ++ primary = tvalue & 0xFF; ++ secondary = (tvalue >> 8) & 0xFF; ++ subordinate = (tvalue >> 16) & 0xFF; ++ primary += pcibios_1st_host_bus_nr(); ++ secondary += pcibios_1st_host_bus_nr(); ++ subordinate += pcibios_1st_host_bus_nr(); ++ tvalue = (tvalue & 0xFF000000) | (u32)primary | (u32)(secondary << 8) | (u32)(subordinate << 16); ++ } ++ return tvalue; ++} ++ ++u32 ifx_pcie_bus_enum_write_hack(int where, u32 value) ++{ ++ u32 tvalue = value; ++ ++ if (where == PCI_PRIMARY_BUS) { ++ u8 primary, secondary, subordinate; ++ ++ primary = tvalue & 0xFF; ++ secondary = (tvalue >> 8) & 0xFF; ++ subordinate = (tvalue >> 16) & 0xFF; ++ if (primary > 0 && primary != 0xFF) { ++ primary -= pcibios_1st_host_bus_nr(); ++ } ++ ++ if (secondary > 0 && secondary != 0xFF) { ++ secondary -= pcibios_1st_host_bus_nr(); ++ } ++ if (subordinate > 0 && subordinate != 0xFF) { ++ subordinate -= pcibios_1st_host_bus_nr(); ++ } ++ tvalue = (tvalue & 0xFF000000) | (u32)primary | (u32)(secondary << 8) | (u32)(subordinate << 16); ++ } ++ else if (where == PCI_SUBORDINATE_BUS) { ++ u8 subordinate = tvalue & 0xFF; ++ ++ subordinate = subordinate > 0 ? subordinate - pcibios_1st_host_bus_nr() : 0; ++ tvalue = subordinate; ++ } ++ return tvalue; ++} ++ ++static int ifx_pcie_read_config(struct pci_bus *bus, u32 devfn, ++ int where, int size, u32 *value) ++{ ++ u32 data = 0; ++ int bus_number = bus->number; ++ static const u32 mask[8] = {0, 0xff, 0xffff, 0, 0xffffffff, 0, 0, 0}; ++ int ret = PCIBIOS_SUCCESSFUL; ++ struct ifx_pci_controller *ctrl = bus->sysdata; ++ int pcie_port = ctrl->port; ++ ++ if (unlikely(size != 1 && size != 2 && size != 4)){ ++ ret = PCIBIOS_BAD_REGISTER_NUMBER; ++ goto out; ++ } ++ ++ /* Make sure the address is aligned to natural boundary */ ++ if (unlikely(((size - 1) & where))) { ++ ret = PCIBIOS_BAD_REGISTER_NUMBER; ++ goto out; ++ } ++ ++ /* ++ * If we are second controller, we have to cheat OS so that it assume ++ * its bus number starts from 0 in host controller ++ */ ++ bus_number = ifx_pcie_bus_nr_deduct(bus_number, pcie_port); ++ ++ /* ++ * We need to force the bus number to be zero on the root ++ * bus. Linux numbers the 2nd root bus to start after all ++ * busses on root 0. ++ */ ++ if (bus->parent == NULL) { ++ bus_number = 0; ++ } ++ ++ /* ++ * PCIe only has a single device connected to it. It is ++ * always device ID 0. Don't bother doing reads for other ++ * device IDs on the first segment. ++ */ ++ if ((bus_number == 0) && (PCI_SLOT(devfn) != 0)) { ++ ret = PCIBIOS_FUNC_NOT_SUPPORTED; ++ goto out; ++ } ++ ++ if (pcie_valid_config(pcie_port, bus_number, PCI_SLOT(devfn)) == 0) { ++ *value = 0xffffffff; ++ ret = PCIBIOS_DEVICE_NOT_FOUND; ++ goto out; ++ } ++ ++ PCIE_IRQ_LOCK(ifx_pcie_lock); ++ if (bus_number == 0) { /* RC itself */ ++ u32 t; ++ ++ t = (where & ~3); ++ data = ifx_pcie_rc_cfg_rd(pcie_port, t); ++ } else { ++ u32 addr = pcie_bus_addr(bus_number, devfn, where); ++ ++ data = ifx_pcie_cfg_rd(pcie_port, addr); ++ #ifdef CONFIG_IFX_PCIE_HW_SWAP ++ data = le32_to_cpu(data); ++ #endif /* CONFIG_IFX_PCIE_HW_SWAP */ ++ } ++ /* To get a correct PCI topology, we have to restore the bus number to OS */ ++ data = ifx_pcie_bus_enum_hack(bus, devfn, where, data, pcie_port, 1); ++ ++ PCIE_IRQ_UNLOCK(ifx_pcie_lock); ++ ++ *value = (data >> (8 * (where & 3))) & mask[size & 7]; ++out: ++ return ret; ++} ++ ++static u32 ifx_pcie_size_to_value(int where, int size, u32 data, u32 value) ++{ ++ u32 shift; ++ u32 tdata = data; ++ ++ switch (size) { ++ case 1: ++ shift = (where & 0x3) << 3; ++ tdata &= ~(0xffU << shift); ++ tdata |= ((value & 0xffU) << shift); ++ break; ++ case 2: ++ shift = (where & 3) << 3; ++ tdata &= ~(0xffffU << shift); ++ tdata |= ((value & 0xffffU) << shift); ++ break; ++ case 4: ++ tdata = value; ++ break; ++ } ++ return tdata; ++} ++ ++static int ifx_pcie_write_config(struct pci_bus *bus, u32 devfn, ++ int where, int size, u32 value) ++{ ++ int bus_number = bus->number; ++ int ret = PCIBIOS_SUCCESSFUL; ++ struct ifx_pci_controller *ctrl = bus->sysdata; ++ int pcie_port = ctrl->port; ++ u32 tvalue = value; ++ u32 data; ++ ++ /* Make sure the address is aligned to natural boundary */ ++ if (unlikely(((size - 1) & where))) { ++ ret = PCIBIOS_BAD_REGISTER_NUMBER; ++ goto out; ++ } ++ /* ++ * If we are second controller, we have to cheat OS so that it assume ++ * its bus number starts from 0 in host controller ++ */ ++ bus_number = ifx_pcie_bus_nr_deduct(bus_number, pcie_port); ++ ++ /* ++ * We need to force the bus number to be zero on the root ++ * bus. Linux numbers the 2nd root bus to start after all ++ * busses on root 0. ++ */ ++ if (bus->parent == NULL) { ++ bus_number = 0; ++ } ++ ++ if (pcie_valid_config(pcie_port, bus_number, PCI_SLOT(devfn)) == 0) { ++ ret = PCIBIOS_DEVICE_NOT_FOUND; ++ goto out; ++ } ++ ++ /* XXX, some PCIe device may need some delay */ ++ PCIE_IRQ_LOCK(ifx_pcie_lock); ++ ++ /* ++ * To configure the correct bus topology using native way, we have to cheat Os so that ++ * it can configure the PCIe hardware correctly. ++ */ ++ tvalue = ifx_pcie_bus_enum_hack(bus, devfn, where, value, pcie_port, 0); ++ ++ if (bus_number == 0) { /* RC itself */ ++ u32 t; ++ ++ t = (where & ~3); ++ data = ifx_pcie_rc_cfg_rd(pcie_port, t); ++ ++ data = ifx_pcie_size_to_value(where, size, data, tvalue); ++ ++ ifx_pcie_rc_cfg_wr(pcie_port, t, data); ++ } else { ++ u32 addr = pcie_bus_addr(bus_number, devfn, where); ++ ++ data = ifx_pcie_cfg_rd(pcie_port, addr); ++#ifdef CONFIG_IFX_PCIE_HW_SWAP ++ data = le32_to_cpu(data); ++#endif ++ ++ data = ifx_pcie_size_to_value(where, size, data, tvalue); ++#ifdef CONFIG_IFX_PCIE_HW_SWAP ++ data = cpu_to_le32(data); ++#endif ++ ifx_pcie_cfg_wr(pcie_port, addr, data); ++ } ++ PCIE_IRQ_UNLOCK(ifx_pcie_lock); ++out: ++ return ret; ++} ++ ++static struct resource ifx_pcie_io_resource = { ++ .name = "PCIe0 I/O space", ++ .start = PCIE_IO_PHY_BASE, ++ .end = PCIE_IO_PHY_END, ++ .flags = IORESOURCE_IO, ++}; ++ ++static struct resource ifx_pcie_mem_resource = { ++ .name = "PCIe0 Memory space", ++ .start = PCIE_MEM_PHY_BASE, ++ .end = PCIE_MEM_PHY_END, ++ .flags = IORESOURCE_MEM, ++}; ++ ++static struct pci_ops ifx_pcie_ops = { ++ .read = ifx_pcie_read_config, ++ .write = ifx_pcie_write_config, ++}; ++ ++static struct ifx_pci_controller ifx_pcie_controller[IFX_PCIE_CORE_NR] = { ++ { ++ .pcic = { ++ .pci_ops = &ifx_pcie_ops, ++ .mem_resource = &ifx_pcie_mem_resource, ++ .io_resource = &ifx_pcie_io_resource, ++ }, ++ .port = IFX_PCIE_PORT0, ++ }, ++}; ++ ++#ifdef IFX_PCIE_ERROR_INT ++ ++static irqreturn_t pcie_rc_core_isr(int irq, void *dev_id) ++{ ++ struct ifx_pci_controller *ctrl = (struct ifx_pci_controller *)dev_id; ++ int pcie_port = ctrl->port; ++ u32 reg; ++ ++ pr_debug("PCIe RC error intr %d\n", irq); ++ reg = IFX_REG_R32(PCIE_IRNCR(pcie_port)); ++ reg &= PCIE_RC_CORE_COMBINED_INT; ++ IFX_REG_W32(reg, PCIE_IRNCR(pcie_port)); ++ ++ return IRQ_HANDLED; ++} ++ ++static int ++pcie_rc_core_int_init(int pcie_port) ++{ ++ int ret; ++ ++ /* Enable core interrupt */ ++ IFX_REG_SET_BIT(PCIE_RC_CORE_COMBINED_INT, PCIE_IRNEN(pcie_port)); ++ ++ /* Clear it first */ ++ IFX_REG_SET_BIT(PCIE_RC_CORE_COMBINED_INT, PCIE_IRNCR(pcie_port)); ++ ret = request_irq(pcie_irqs[pcie_port].ir_irq.irq, pcie_rc_core_isr, 0, ++ pcie_irqs[pcie_port].ir_irq.name, &ifx_pcie_controller[pcie_port]); ++ if (ret) ++ printk(KERN_ERR "%s request irq %d failed\n", __func__, IFX_PCIE_IR); ++ ++ return ret; ++} ++#endif ++ ++int ifx_pcie_bios_map_irq(IFX_PCI_CONST struct pci_dev *dev, u8 slot, u8 pin) ++{ ++ u32 irq_bit = 0; ++ int irq = 0; ++ struct ifx_pci_controller *ctrl = dev->bus->sysdata; ++ int pcie_port = ctrl->port; ++ ++ printk("%s port %d dev %s slot %d pin %d \n", __func__, pcie_port, pci_name(dev), slot, pin); ++ ++ if ((pin == PCIE_LEGACY_DISABLE) || (pin > PCIE_LEGACY_INT_MAX)) { ++ printk(KERN_WARNING "WARNING: dev %s: invalid interrupt pin %d\n", pci_name(dev), pin); ++ return -1; ++ } ++ ++ /* Pin index so minus one */ ++ irq_bit = pcie_irqs[pcie_port].legacy_irq[pin - 1].irq_bit; ++ irq = pcie_irqs[pcie_port].legacy_irq[pin - 1].irq; ++ IFX_REG_SET_BIT(irq_bit, PCIE_IRNEN(pcie_port)); ++ IFX_REG_SET_BIT(irq_bit, PCIE_IRNCR(pcie_port)); ++ printk("%s dev %s irq %d assigned\n", __func__, pci_name(dev), irq); ++ return irq; ++} ++ ++int ifx_pcie_bios_plat_dev_init(struct pci_dev *dev) ++{ ++ u16 config; ++#ifdef IFX_PCIE_ERROR_INT ++ u32 dconfig; ++ int pos; ++#endif ++ ++ /* Enable reporting System errors and parity errors on all devices */ ++ /* Enable parity checking and error reporting */ ++ pci_read_config_word(dev, PCI_COMMAND, &config); ++ config |= PCI_COMMAND_PARITY | PCI_COMMAND_SERR /*| PCI_COMMAND_INVALIDATE | ++ PCI_COMMAND_FAST_BACK*/; ++ pci_write_config_word(dev, PCI_COMMAND, config); ++ ++ if (dev->subordinate) { ++ /* Set latency timers on sub bridges */ ++ pci_write_config_byte(dev, PCI_SEC_LATENCY_TIMER, 0x40); /* XXX, */ ++ /* More bridge error detection */ ++ pci_read_config_word(dev, PCI_BRIDGE_CONTROL, &config); ++ config |= PCI_BRIDGE_CTL_PARITY | PCI_BRIDGE_CTL_SERR; ++ pci_write_config_word(dev, PCI_BRIDGE_CONTROL, config); ++ } ++#ifdef IFX_PCIE_ERROR_INT ++ /* Enable the PCIe normal error reporting */ ++ pos = pci_find_capability(dev, PCI_CAP_ID_EXP); ++ if (pos) { ++ ++ /* Disable system error generation in response to error messages */ ++ pci_read_config_word(dev, pos + PCI_EXP_RTCTL, &config); ++ config &= ~(PCI_EXP_RTCTL_SECEE | PCI_EXP_RTCTL_SENFEE | PCI_EXP_RTCTL_SEFEE); ++ pci_write_config_word(dev, pos + PCI_EXP_RTCTL, config); ++ ++ /* Clear PCIE Capability's Device Status */ ++ pci_read_config_word(dev, pos + PCI_EXP_DEVSTA, &config); ++ pci_write_config_word(dev, pos + PCI_EXP_DEVSTA, config); ++ ++ /* Update Device Control */ ++ pci_read_config_word(dev, pos + PCI_EXP_DEVCTL, &config); ++ /* Correctable Error Reporting */ ++ config |= PCI_EXP_DEVCTL_CERE; ++ /* Non-Fatal Error Reporting */ ++ config |= PCI_EXP_DEVCTL_NFERE; ++ /* Fatal Error Reporting */ ++ config |= PCI_EXP_DEVCTL_FERE; ++ /* Unsupported Request */ ++ config |= PCI_EXP_DEVCTL_URRE; ++ pci_write_config_word(dev, pos + PCI_EXP_DEVCTL, config); ++ } ++ ++ /* Find the Advanced Error Reporting capability */ ++ pos = pci_find_ext_capability(dev, PCI_EXT_CAP_ID_ERR); ++ if (pos) { ++ /* Clear Uncorrectable Error Status */ ++ pci_read_config_dword(dev, pos + PCI_ERR_UNCOR_STATUS, &dconfig); ++ pci_write_config_dword(dev, pos + PCI_ERR_UNCOR_STATUS, dconfig); ++ /* Enable reporting of all uncorrectable errors */ ++ /* Uncorrectable Error Mask - turned on bits disable errors */ ++ pci_write_config_dword(dev, pos + PCI_ERR_UNCOR_MASK, 0); ++ /* ++ * Leave severity at HW default. This only controls if ++ * errors are reported as uncorrectable or ++ * correctable, not if the error is reported. ++ */ ++ /* PCI_ERR_UNCOR_SEVER - Uncorrectable Error Severity */ ++ /* Clear Correctable Error Status */ ++ pci_read_config_dword(dev, pos + PCI_ERR_COR_STATUS, &dconfig); ++ pci_write_config_dword(dev, pos + PCI_ERR_COR_STATUS, dconfig); ++ /* Enable reporting of all correctable errors */ ++ /* Correctable Error Mask - turned on bits disable errors */ ++ pci_write_config_dword(dev, pos + PCI_ERR_COR_MASK, 0); ++ /* Advanced Error Capabilities */ ++ pci_read_config_dword(dev, pos + PCI_ERR_CAP, &dconfig); ++ /* ECRC Generation Enable */ ++ if (dconfig & PCI_ERR_CAP_ECRC_GENC) { ++ dconfig |= PCI_ERR_CAP_ECRC_GENE; ++ } ++ /* ECRC Check Enable */ ++ if (dconfig & PCI_ERR_CAP_ECRC_CHKC) { ++ dconfig |= PCI_ERR_CAP_ECRC_CHKE; ++ } ++ pci_write_config_dword(dev, pos + PCI_ERR_CAP, dconfig); ++ ++ /* PCI_ERR_HEADER_LOG - Header Log Register (16 bytes) */ ++ /* Enable Root Port's interrupt in response to error messages */ ++ pci_write_config_dword(dev, pos + PCI_ERR_ROOT_COMMAND, ++ PCI_ERR_ROOT_CMD_COR_EN | ++ PCI_ERR_ROOT_CMD_NONFATAL_EN | ++ PCI_ERR_ROOT_CMD_FATAL_EN); ++ /* Clear the Root status register */ ++ pci_read_config_dword(dev, pos + PCI_ERR_ROOT_STATUS, &dconfig); ++ pci_write_config_dword(dev, pos + PCI_ERR_ROOT_STATUS, dconfig); ++ } ++#endif /* IFX_PCIE_ERROR_INT */ ++ /* WAR, only 128 MRRS is supported, force all EPs to support this value */ ++ pcie_set_readrq(dev, 128); ++ return 0; ++} ++ ++static int ++pcie_rc_initialize(int pcie_port) ++{ ++ int i; ++#define IFX_PCIE_PHY_LOOP_CNT 5 ++ ++ pcie_rcu_endian_setup(pcie_port); ++ ++ pcie_ep_gpio_rst_init(pcie_port); ++ ++ /* ++ * XXX, PCIe elastic buffer bug will cause not to be detected. One more ++ * reset PCIe PHY will solve this issue ++ */ ++ for (i = 0; i < IFX_PCIE_PHY_LOOP_CNT; i++) { ++ /* Disable PCIe PHY Analog part for sanity check */ ++ pcie_phy_pmu_disable(pcie_port); ++ ++ pcie_phy_rst_assert(pcie_port); ++ pcie_phy_rst_deassert(pcie_port); ++ ++ /* Make sure PHY PLL is stable */ ++ udelay(20); ++ ++ /* PCIe Core reset enabled, low active, sw programmed */ ++ pcie_core_rst_assert(pcie_port); ++ ++ /* Put PCIe EP in reset status */ ++ pcie_device_rst_assert(pcie_port); ++ ++ /* PCI PHY & Core reset disabled, high active, sw programmed */ ++ pcie_core_rst_deassert(pcie_port); ++ ++ /* Already in a quiet state, program PLL, enable PHY, check ready bit */ ++ pcie_phy_clock_mode_setup(pcie_port); ++ ++ /* Enable PCIe PHY and Clock */ ++ pcie_core_pmu_setup(pcie_port); ++ ++ /* Clear status registers */ ++ pcie_status_register_clear(pcie_port); ++ ++#ifdef CONFIG_PCI_MSI ++ pcie_msi_init(pcie_port); ++#endif /* CONFIG_PCI_MSI */ ++ pcie_rc_cfg_reg_setup(pcie_port); ++ ++ /* Once link is up, break out */ ++ if (pcie_app_loigc_setup(pcie_port) == 0) ++ break; ++ } ++ if (i >= IFX_PCIE_PHY_LOOP_CNT) { ++ printk(KERN_ERR "%s link up failed!!!!!\n", __func__); ++ return -EIO; ++ } ++ /* NB, don't increase ACK/NACK timer timeout value, which will cause a lot of COR errors */ ++ pcie_replay_time_update(pcie_port); ++ return 0; ++} ++ ++static int __init ifx_pcie_bios_init(void) ++{ ++ void __iomem *io_map_base; ++ int pcie_port; ++ int startup_port; ++ ++ /* Enable AHB Master/ Slave */ ++ pcie_ahb_pmu_setup(); ++ ++ startup_port = IFX_PCIE_PORT0; ++ ++ for (pcie_port = startup_port; pcie_port < IFX_PCIE_CORE_NR; pcie_port++){ ++ if (pcie_rc_initialize(pcie_port) == 0) { ++ IFX_PCIE_PRINT(PCIE_MSG_INIT, "%s: ifx_pcie_cfg_base 0x%p\n", ++ __func__, PCIE_CFG_PORT_TO_BASE(pcie_port)); ++ /* Otherwise, warning will pop up */ ++ io_map_base = ioremap(PCIE_IO_PHY_PORT_TO_BASE(pcie_port), PCIE_IO_SIZE); ++ if (io_map_base == NULL) { ++ IFX_PCIE_PRINT(PCIE_MSG_ERR, "%s io space ioremap failed\n", __func__); ++ return -ENOMEM; ++ } ++ ifx_pcie_controller[pcie_port].pcic.io_map_base = (unsigned long)io_map_base; ++ ++ register_pci_controller(&ifx_pcie_controller[pcie_port].pcic); ++ /* XXX, clear error status */ ++ ++ IFX_PCIE_PRINT(PCIE_MSG_INIT, "%s: mem_resource 0x%p, io_resource 0x%p\n", ++ __func__, &ifx_pcie_controller[pcie_port].pcic.mem_resource, ++ &ifx_pcie_controller[pcie_port].pcic.io_resource); ++ ++ #ifdef IFX_PCIE_ERROR_INT ++ pcie_rc_core_int_init(pcie_port); ++ #endif /* IFX_PCIE_ERROR_INT */ ++ } ++ } ++ ++ return 0; ++} ++arch_initcall(ifx_pcie_bios_init); ++ ++MODULE_LICENSE("GPL"); ++MODULE_AUTHOR("Chuanhua.Lei@infineon.com"); ++MODULE_SUPPORTED_DEVICE("Infineon builtin PCIe RC module"); ++MODULE_DESCRIPTION("Infineon builtin PCIe RC driver"); ++ +--- /dev/null ++++ b/arch/mips/pci/ifxmips_pcie.h +@@ -0,0 +1,135 @@ ++/****************************************************************************** ++** ++** FILE NAME : ifxmips_pcie.h ++** PROJECT : IFX UEIP for VRX200 ++** MODULES : PCIe module ++** ++** DATE : 02 Mar 2009 ++** AUTHOR : Lei Chuanhua ++** DESCRIPTION : PCIe Root Complex Driver ++** COPYRIGHT : Copyright (c) 2009 ++** Infineon Technologies AG ++** Am Campeon 1-12, 85579 Neubiberg, Germany ++** ++** This program is free software; you can redistribute it and/or modify ++** it under the terms of the GNU General Public License as published by ++** the Free Software Foundation; either version 2 of the License, or ++** (at your option) any later version. ++** HISTORY ++** $Version $Date $Author $Comment ++** 0.0.1 17 Mar,2009 Lei Chuanhua Initial version ++*******************************************************************************/ ++#ifndef IFXMIPS_PCIE_H ++#define IFXMIPS_PCIE_H ++#include ++#include ++#include ++#include ++#include "ifxmips_pci_common.h" ++#include "ifxmips_pcie_reg.h" ++ ++/*! ++ \defgroup IFX_PCIE PCI Express bus driver module ++ \brief PCI Express IP module support VRX200 ++*/ ++ ++/*! ++ \defgroup IFX_PCIE_OS OS APIs ++ \ingroup IFX_PCIE ++ \brief PCIe bus driver OS interface functions ++*/ ++ ++/*! ++ \file ifxmips_pcie.h ++ \ingroup IFX_PCIE ++ \brief header file for PCIe module common header file ++*/ ++#define PCIE_IRQ_LOCK(lock) do { \ ++ unsigned long flags; \ ++ spin_lock_irqsave(&(lock), flags); ++#define PCIE_IRQ_UNLOCK(lock) \ ++ spin_unlock_irqrestore(&(lock), flags); \ ++} while (0) ++ ++#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,18) ++#define IRQF_SHARED SA_SHIRQ ++#endif ++ ++#define PCIE_MSG_MSI 0x00000001 ++#define PCIE_MSG_ISR 0x00000002 ++#define PCIE_MSG_FIXUP 0x00000004 ++#define PCIE_MSG_READ_CFG 0x00000008 ++#define PCIE_MSG_WRITE_CFG 0x00000010 ++#define PCIE_MSG_CFG (PCIE_MSG_READ_CFG | PCIE_MSG_WRITE_CFG) ++#define PCIE_MSG_REG 0x00000020 ++#define PCIE_MSG_INIT 0x00000040 ++#define PCIE_MSG_ERR 0x00000080 ++#define PCIE_MSG_PHY 0x00000100 ++#define PCIE_MSG_ANY 0x000001ff ++ ++#define IFX_PCIE_PORT0 0 ++#define IFX_PCIE_PORT1 1 ++ ++#ifdef CONFIG_IFX_PCIE_2ND_CORE ++#define IFX_PCIE_CORE_NR 2 ++#else ++#define IFX_PCIE_CORE_NR 1 ++#endif ++ ++#define IFX_PCIE_ERROR_INT ++ ++//#define IFX_PCIE_DBG ++ ++#if defined(IFX_PCIE_DBG) ++#define IFX_PCIE_PRINT(_m, _fmt, args...) do { \ ++ ifx_pcie_debug((_fmt), ##args); \ ++} while (0) ++ ++#define INLINE ++#else ++#define IFX_PCIE_PRINT(_m, _fmt, args...) \ ++ do {} while(0) ++#define INLINE inline ++#endif ++ ++struct ifx_pci_controller { ++ struct pci_controller pcic; ++ ++ /* RC specific, per host bus information */ ++ u32 port; /* Port index, 0 -- 1st core, 1 -- 2nd core */ ++}; ++ ++typedef struct ifx_pcie_ir_irq { ++ const unsigned int irq; ++ const char name[16]; ++}ifx_pcie_ir_irq_t; ++ ++typedef struct ifx_pcie_legacy_irq{ ++ const u32 irq_bit; ++ const int irq; ++}ifx_pcie_legacy_irq_t; ++ ++typedef struct ifx_pcie_irq { ++ ifx_pcie_ir_irq_t ir_irq; ++ ifx_pcie_legacy_irq_t legacy_irq[PCIE_LEGACY_INT_MAX]; ++}ifx_pcie_irq_t; ++ ++extern u32 g_pcie_debug_flag; ++extern void ifx_pcie_debug(const char *fmt, ...); ++extern void pcie_phy_clock_mode_setup(int pcie_port); ++extern void pcie_msi_pic_init(int pcie_port); ++extern u32 ifx_pcie_bus_enum_read_hack(int where, u32 value); ++extern u32 ifx_pcie_bus_enum_write_hack(int where, u32 value); ++ ++#define CONFIG_VR9 ++ ++#ifdef CONFIG_VR9 ++#include "ifxmips_pcie_vr9.h" ++#elif defined (CONFIG_AR10) ++#include "ifxmips_pcie_ar10.h" ++#else ++#error "PCIE: platform not defined" ++#endif /* CONFIG_VR9 */ ++ ++#endif /* IFXMIPS_PCIE_H */ ++ +--- /dev/null ++++ b/arch/mips/pci/ifxmips_pcie_ar10.h +@@ -0,0 +1,290 @@ ++/**************************************************************************** ++ Copyright (c) 2010 ++ Lantiq Deutschland GmbH ++ Am Campeon 3; 85579 Neubiberg, Germany ++ ++ For licensing information, see the file 'LICENSE' in the root folder of ++ this software module. ++ ++ *****************************************************************************/ ++/*! ++ \file ifxmips_pcie_ar10.h ++ \ingroup IFX_PCIE ++ \brief PCIe RC driver ar10 specific file ++*/ ++ ++#ifndef IFXMIPS_PCIE_AR10_H ++#define IFXMIPS_PCIE_AR10_H ++#ifndef AUTOCONF_INCLUDED ++#include ++#endif /* AUTOCONF_INCLUDED */ ++#include ++#include ++ ++/* Project header file */ ++#include ++#include ++#include ++#include ++ ++static inline void pcie_ep_gpio_rst_init(int pcie_port) ++{ ++ ifx_ebu_led_enable(); ++ if (pcie_port == 0) { ++ ifx_ebu_led_set_data(11, 1); ++ } ++ else { ++ ifx_ebu_led_set_data(12, 1); ++ } ++} ++ ++static inline void pcie_ahb_pmu_setup(void) ++{ ++ /* XXX, moved to CGU to control AHBM */ ++} ++ ++static inline void pcie_rcu_endian_setup(int pcie_port) ++{ ++ u32 reg; ++ ++ reg = IFX_REG_R32(IFX_RCU_AHB_ENDIAN); ++ /* Inbound, big endian */ ++ reg |= IFX_RCU_BE_AHB4S; ++ if (pcie_port == 0) { ++ reg |= IFX_RCU_BE_PCIE0M; ++ ++ #ifdef CONFIG_IFX_PCIE_HW_SWAP ++ /* Outbound, software swap needed */ ++ reg |= IFX_RCU_BE_AHB3M; ++ reg &= ~IFX_RCU_BE_PCIE0S; ++ #else ++ /* Outbound little endian */ ++ reg &= ~IFX_RCU_BE_AHB3M; ++ reg &= ~IFX_RCU_BE_PCIE0S; ++ #endif ++ } ++ else { ++ reg |= IFX_RCU_BE_PCIE1M; ++ #ifdef CONFIG_IFX_PCIE1_HW_SWAP ++ /* Outbound, software swap needed */ ++ reg |= IFX_RCU_BE_AHB3M; ++ reg &= ~IFX_RCU_BE_PCIE1S; ++ #else ++ /* Outbound little endian */ ++ reg &= ~IFX_RCU_BE_AHB3M; ++ reg &= ~IFX_RCU_BE_PCIE1S; ++ #endif ++ } ++ ++ IFX_REG_W32(reg, IFX_RCU_AHB_ENDIAN); ++ IFX_PCIE_PRINT(PCIE_MSG_REG, "%s IFX_RCU_AHB_ENDIAN: 0x%08x\n", __func__, IFX_REG_R32(IFX_RCU_AHB_ENDIAN)); ++} ++ ++static inline void pcie_phy_pmu_enable(int pcie_port) ++{ ++ if (pcie_port == 0) { /* XXX, should use macro*/ ++ PCIE0_PHY_PMU_SETUP(IFX_PMU_ENABLE); ++ } ++ else { ++ PCIE1_PHY_PMU_SETUP(IFX_PMU_ENABLE); ++ } ++} ++ ++static inline void pcie_phy_pmu_disable(int pcie_port) ++{ ++ if (pcie_port == 0) { /* XXX, should use macro*/ ++ PCIE0_PHY_PMU_SETUP(IFX_PMU_DISABLE); ++ } ++ else { ++ PCIE1_PHY_PMU_SETUP(IFX_PMU_DISABLE); ++ } ++} ++ ++static inline void pcie_pdi_big_endian(int pcie_port) ++{ ++ u32 reg; ++ ++ reg = IFX_REG_R32(IFX_RCU_AHB_ENDIAN); ++ if (pcie_port == 0) { ++ /* Config AHB->PCIe and PDI endianness */ ++ reg |= IFX_RCU_BE_PCIE0_PDI; ++ } ++ else { ++ /* Config AHB->PCIe and PDI endianness */ ++ reg |= IFX_RCU_BE_PCIE1_PDI; ++ } ++ IFX_REG_W32(reg, IFX_RCU_AHB_ENDIAN); ++} ++ ++static inline void pcie_pdi_pmu_enable(int pcie_port) ++{ ++ if (pcie_port == 0) { ++ /* Enable PDI to access PCIe PHY register */ ++ PDI0_PMU_SETUP(IFX_PMU_ENABLE); ++ } ++ else { ++ PDI1_PMU_SETUP(IFX_PMU_ENABLE); ++ } ++} ++ ++static inline void pcie_core_rst_assert(int pcie_port) ++{ ++ u32 reg; ++ ++ reg = IFX_REG_R32(IFX_RCU_RST_REQ); ++ ++ /* Reset Core, bit 22 */ ++ if (pcie_port == 0) { ++ reg |= 0x00400000; ++ } ++ else { ++ reg |= 0x08000000; /* Bit 27 */ ++ } ++ IFX_REG_W32(reg, IFX_RCU_RST_REQ); ++} ++ ++static inline void pcie_core_rst_deassert(int pcie_port) ++{ ++ u32 reg; ++ ++ /* Make sure one micro-second delay */ ++ udelay(1); ++ ++ reg = IFX_REG_R32(IFX_RCU_RST_REQ); ++ if (pcie_port == 0) { ++ reg &= ~0x00400000; /* bit 22 */ ++ } ++ else { ++ reg &= ~0x08000000; /* Bit 27 */ ++ } ++ IFX_REG_W32(reg, IFX_RCU_RST_REQ); ++} ++ ++static inline void pcie_phy_rst_assert(int pcie_port) ++{ ++ u32 reg; ++ ++ reg = IFX_REG_R32(IFX_RCU_RST_REQ); ++ if (pcie_port == 0) { ++ reg |= 0x00001000; /* Bit 12 */ ++ } ++ else { ++ reg |= 0x00002000; /* Bit 13 */ ++ } ++ IFX_REG_W32(reg, IFX_RCU_RST_REQ); ++} ++ ++static inline void pcie_phy_rst_deassert(int pcie_port) ++{ ++ u32 reg; ++ ++ /* Make sure one micro-second delay */ ++ udelay(1); ++ ++ reg = IFX_REG_R32(IFX_RCU_RST_REQ); ++ if (pcie_port == 0) { ++ reg &= ~0x00001000; /* Bit 12 */ ++ } ++ else { ++ reg &= ~0x00002000; /* Bit 13 */ ++ } ++ IFX_REG_W32(reg, IFX_RCU_RST_REQ); ++} ++ ++static inline void pcie_device_rst_assert(int pcie_port) ++{ ++ if (pcie_port == 0) { ++ ifx_ebu_led_set_data(11, 0); ++ } ++ else { ++ ifx_ebu_led_set_data(12, 0); ++ } ++} ++ ++static inline void pcie_device_rst_deassert(int pcie_port) ++{ ++ mdelay(100); ++ if (pcie_port == 0) { ++ ifx_ebu_led_set_data(11, 1); ++ } ++ else { ++ ifx_ebu_led_set_data(12, 1); ++ } ++ ifx_ebu_led_disable(); ++} ++ ++static inline void pcie_core_pmu_setup(int pcie_port) ++{ ++ if (pcie_port == 0) { ++ PCIE0_CTRL_PMU_SETUP(IFX_PMU_ENABLE); ++ } ++ else { ++ PCIE1_CTRL_PMU_SETUP(IFX_PMU_ENABLE); ++ } ++} ++ ++static inline void pcie_msi_init(int pcie_port) ++{ ++ pcie_msi_pic_init(pcie_port); ++ if (pcie_port == 0) { ++ MSI0_PMU_SETUP(IFX_PMU_ENABLE); ++ } ++ else { ++ MSI1_PMU_SETUP(IFX_PMU_ENABLE); ++ } ++} ++ ++static inline u32 ++ifx_pcie_bus_nr_deduct(u32 bus_number, int pcie_port) ++{ ++ u32 tbus_number = bus_number; ++ ++#ifdef CONFIG_IFX_PCIE_2ND_CORE ++ if (pcie_port == IFX_PCIE_PORT1) { /* Port 1 must check if there are two cores enabled */ ++ if (pcibios_host_nr() > 1) { ++ tbus_number -= pcibios_1st_host_bus_nr(); ++ } ++ } ++#endif /* CONFIG_IFX_PCI */ ++ return tbus_number; ++} ++ ++static inline u32 ++ifx_pcie_bus_enum_hack(struct pci_bus *bus, u32 devfn, int where, u32 value, int pcie_port, int read) ++{ ++ struct pci_dev *pdev; ++ u32 tvalue = value; ++ ++ /* Sanity check */ ++ pdev = pci_get_slot(bus, devfn); ++ if (pdev == NULL) { ++ return tvalue; ++ } ++ ++ /* Only care about PCI bridge */ ++ if (pdev->hdr_type != PCI_HEADER_TYPE_BRIDGE) { ++ return tvalue; ++ } ++ ++ if (read) { /* Read hack */ ++ #ifdef CONFIG_IFX_PCIE_2ND_CORE ++ if (pcie_port == IFX_PCIE_PORT1) { /* Port 1 must check if there are two cores enabled */ ++ if (pcibios_host_nr() > 1) { ++ tvalue = ifx_pcie_bus_enum_read_hack(where, tvalue); ++ } ++ } ++ #endif /* CONFIG_IFX_PCIE_2ND_CORE */ ++ } ++ else { /* Write hack */ ++ #ifdef CONFIG_IFX_PCIE_2ND_CORE ++ if (pcie_port == IFX_PCIE_PORT1) { /* Port 1 must check if there are two cores enabled */ ++ if (pcibios_host_nr() > 1) { ++ tvalue = ifx_pcie_bus_enum_write_hack(where, tvalue); ++ } ++ } ++ #endif ++ } ++ return tvalue; ++} ++ ++#endif /* IFXMIPS_PCIE_AR10_H */ +--- /dev/null ++++ b/arch/mips/pci/ifxmips_pcie_msi.c +@@ -0,0 +1,392 @@ ++/****************************************************************************** ++** ++** FILE NAME : ifxmips_pcie_msi.c ++** PROJECT : IFX UEIP for VRX200 ++** MODULES : PCI MSI sub module ++** ++** DATE : 02 Mar 2009 ++** AUTHOR : Lei Chuanhua ++** DESCRIPTION : PCIe MSI Driver ++** COPYRIGHT : Copyright (c) 2009 ++** Infineon Technologies AG ++** Am Campeon 1-12, 85579 Neubiberg, Germany ++** ++** This program is free software; you can redistribute it and/or modify ++** it under the terms of the GNU General Public License as published by ++** the Free Software Foundation; either version 2 of the License, or ++** (at your option) any later version. ++** HISTORY ++** $Date $Author $Comment ++** 02 Mar,2009 Lei Chuanhua Initial version ++*******************************************************************************/ ++/*! ++ \defgroup IFX_PCIE_MSI MSI OS APIs ++ \ingroup IFX_PCIE ++ \brief PCIe bus driver OS interface functions ++*/ ++ ++/*! ++ \file ifxmips_pcie_msi.c ++ \ingroup IFX_PCIE ++ \brief PCIe MSI OS interface file ++*/ ++ ++#ifndef AUTOCONF_INCLUDED ++#include ++#endif /* AUTOCONF_INCLUDED */ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++#include ++#include ++#include ++ ++#include "ifxmips_pcie_reg.h" ++#include "ifxmips_pcie.h" ++ ++#define IFX_MSI_IRQ_NUM 16 ++ ++enum { ++ IFX_PCIE_MSI_IDX0 = 0, ++ IFX_PCIE_MSI_IDX1, ++ IFX_PCIE_MSI_IDX2, ++ IFX_PCIE_MSI_IDX3, ++}; ++ ++typedef struct ifx_msi_irq_idx { ++ const int irq; ++ const int idx; ++}ifx_msi_irq_idx_t; ++ ++struct ifx_msi_pic { ++ volatile u32 pic_table[IFX_MSI_IRQ_NUM]; ++ volatile u32 pic_endian; /* 0x40 */ ++}; ++typedef struct ifx_msi_pic *ifx_msi_pic_t; ++ ++typedef struct ifx_msi_irq { ++ const volatile ifx_msi_pic_t msi_pic_p; ++ const u32 msi_phy_base; ++ const ifx_msi_irq_idx_t msi_irq_idx[IFX_MSI_IRQ_NUM]; ++ /* ++ * Each bit in msi_free_irq_bitmask represents a MSI interrupt that is ++ * in use. ++ */ ++ u16 msi_free_irq_bitmask; ++ ++ /* ++ * Each bit in msi_multiple_irq_bitmask tells that the device using ++ * this bit in msi_free_irq_bitmask is also using the next bit. This ++ * is used so we can disable all of the MSI interrupts when a device ++ * uses multiple. ++ */ ++ u16 msi_multiple_irq_bitmask; ++}ifx_msi_irq_t; ++ ++static ifx_msi_irq_t msi_irqs[IFX_PCIE_CORE_NR] = { ++ { ++ .msi_pic_p = (const volatile ifx_msi_pic_t)IFX_MSI_PIC_REG_BASE, ++ .msi_phy_base = PCIE_MSI_PHY_BASE, ++ .msi_irq_idx = { ++ {IFX_PCIE_MSI_IR0, IFX_PCIE_MSI_IDX0}, {IFX_PCIE_MSI_IR1, IFX_PCIE_MSI_IDX1}, ++ {IFX_PCIE_MSI_IR2, IFX_PCIE_MSI_IDX2}, {IFX_PCIE_MSI_IR3, IFX_PCIE_MSI_IDX3}, ++ {IFX_PCIE_MSI_IR0, IFX_PCIE_MSI_IDX0}, {IFX_PCIE_MSI_IR1, IFX_PCIE_MSI_IDX1}, ++ {IFX_PCIE_MSI_IR2, IFX_PCIE_MSI_IDX2}, {IFX_PCIE_MSI_IR3, IFX_PCIE_MSI_IDX3}, ++ {IFX_PCIE_MSI_IR0, IFX_PCIE_MSI_IDX0}, {IFX_PCIE_MSI_IR1, IFX_PCIE_MSI_IDX1}, ++ {IFX_PCIE_MSI_IR2, IFX_PCIE_MSI_IDX2}, {IFX_PCIE_MSI_IR3, IFX_PCIE_MSI_IDX3}, ++ {IFX_PCIE_MSI_IR0, IFX_PCIE_MSI_IDX0}, {IFX_PCIE_MSI_IR1, IFX_PCIE_MSI_IDX1}, ++ {IFX_PCIE_MSI_IR2, IFX_PCIE_MSI_IDX2}, {IFX_PCIE_MSI_IR3, IFX_PCIE_MSI_IDX3}, ++ }, ++ .msi_free_irq_bitmask = 0, ++ .msi_multiple_irq_bitmask= 0, ++ }, ++#ifdef CONFIG_IFX_PCIE_2ND_CORE ++ { ++ .msi_pic_p = (const volatile ifx_msi_pic_t)IFX_MSI1_PIC_REG_BASE, ++ .msi_phy_base = PCIE1_MSI_PHY_BASE, ++ .msi_irq_idx = { ++ {IFX_PCIE1_MSI_IR0, IFX_PCIE_MSI_IDX0}, {IFX_PCIE1_MSI_IR1, IFX_PCIE_MSI_IDX1}, ++ {IFX_PCIE1_MSI_IR2, IFX_PCIE_MSI_IDX2}, {IFX_PCIE1_MSI_IR3, IFX_PCIE_MSI_IDX3}, ++ {IFX_PCIE1_MSI_IR0, IFX_PCIE_MSI_IDX0}, {IFX_PCIE1_MSI_IR1, IFX_PCIE_MSI_IDX1}, ++ {IFX_PCIE1_MSI_IR2, IFX_PCIE_MSI_IDX2}, {IFX_PCIE1_MSI_IR3, IFX_PCIE_MSI_IDX3}, ++ {IFX_PCIE1_MSI_IR0, IFX_PCIE_MSI_IDX0}, {IFX_PCIE1_MSI_IR1, IFX_PCIE_MSI_IDX1}, ++ {IFX_PCIE1_MSI_IR2, IFX_PCIE_MSI_IDX2}, {IFX_PCIE1_MSI_IR3, IFX_PCIE_MSI_IDX3}, ++ {IFX_PCIE1_MSI_IR0, IFX_PCIE_MSI_IDX0}, {IFX_PCIE1_MSI_IR1, IFX_PCIE_MSI_IDX1}, ++ {IFX_PCIE1_MSI_IR2, IFX_PCIE_MSI_IDX2}, {IFX_PCIE1_MSI_IR3, IFX_PCIE_MSI_IDX3}, ++ }, ++ .msi_free_irq_bitmask = 0, ++ .msi_multiple_irq_bitmask= 0, ++ ++ }, ++#endif /* CONFIG_IFX_PCIE_2ND_CORE */ ++}; ++ ++/* ++ * This lock controls updates to msi_free_irq_bitmask, ++ * msi_multiple_irq_bitmask and pic register settting ++ */ ++static DEFINE_SPINLOCK(ifx_pcie_msi_lock); ++ ++void pcie_msi_pic_init(int pcie_port) ++{ ++ spin_lock(&ifx_pcie_msi_lock); ++ msi_irqs[pcie_port].msi_pic_p->pic_endian = IFX_MSI_PIC_BIG_ENDIAN; ++ spin_unlock(&ifx_pcie_msi_lock); ++} ++ ++/** ++ * \fn int arch_setup_msi_irq(struct pci_dev *pdev, struct msi_desc *desc) ++ * \brief Called when a driver request MSI interrupts instead of the ++ * legacy INT A-D. This routine will allocate multiple interrupts ++ * for MSI devices that support them. A device can override this by ++ * programming the MSI control bits [6:4] before calling ++ * pci_enable_msi(). ++ * ++ * \param[in] pdev Device requesting MSI interrupts ++ * \param[in] desc MSI descriptor ++ * ++ * \return -EINVAL Invalid pcie root port or invalid msi bit ++ * \return 0 OK ++ * \ingroup IFX_PCIE_MSI ++ */ ++int ++arch_setup_msi_irq(struct pci_dev *pdev, struct msi_desc *desc) ++{ ++ int irq, pos; ++ u16 control; ++ int irq_idx; ++ int irq_step; ++ int configured_private_bits; ++ int request_private_bits; ++ struct msi_msg msg; ++ u16 search_mask; ++ struct ifx_pci_controller *ctrl = pdev->bus->sysdata; ++ int pcie_port = ctrl->port; ++ ++ IFX_PCIE_PRINT(PCIE_MSG_MSI, "%s %s enter\n", __func__, pci_name(pdev)); ++ ++ /* XXX, skip RC MSI itself */ ++ if (pdev->pcie_type == PCI_EXP_TYPE_ROOT_PORT) { ++ IFX_PCIE_PRINT(PCIE_MSG_MSI, "%s RC itself doesn't use MSI interrupt\n", __func__); ++ return -EINVAL; ++ } ++ ++ /* ++ * Read the MSI config to figure out how many IRQs this device ++ * wants. Most devices only want 1, which will give ++ * configured_private_bits and request_private_bits equal 0. ++ */ ++ pci_read_config_word(pdev, desc->msi_attrib.pos + PCI_MSI_FLAGS, &control); ++ ++ /* ++ * If the number of private bits has been configured then use ++ * that value instead of the requested number. This gives the ++ * driver the chance to override the number of interrupts ++ * before calling pci_enable_msi(). ++ */ ++ configured_private_bits = (control & PCI_MSI_FLAGS_QSIZE) >> 4; ++ if (configured_private_bits == 0) { ++ /* Nothing is configured, so use the hardware requested size */ ++ request_private_bits = (control & PCI_MSI_FLAGS_QMASK) >> 1; ++ } ++ else { ++ /* ++ * Use the number of configured bits, assuming the ++ * driver wanted to override the hardware request ++ * value. ++ */ ++ request_private_bits = configured_private_bits; ++ } ++ ++ /* ++ * The PCI 2.3 spec mandates that there are at most 32 ++ * interrupts. If this device asks for more, only give it one. ++ */ ++ if (request_private_bits > 5) { ++ request_private_bits = 0; ++ } ++again: ++ /* ++ * The IRQs have to be aligned on a power of two based on the ++ * number being requested. ++ */ ++ irq_step = (1 << request_private_bits); ++ ++ /* Mask with one bit for each IRQ */ ++ search_mask = (1 << irq_step) - 1; ++ ++ /* ++ * We're going to search msi_free_irq_bitmask_lock for zero ++ * bits. This represents an MSI interrupt number that isn't in ++ * use. ++ */ ++ spin_lock(&ifx_pcie_msi_lock); ++ for (pos = 0; pos < IFX_MSI_IRQ_NUM; pos += irq_step) { ++ if ((msi_irqs[pcie_port].msi_free_irq_bitmask & (search_mask << pos)) == 0) { ++ msi_irqs[pcie_port].msi_free_irq_bitmask |= search_mask << pos; ++ msi_irqs[pcie_port].msi_multiple_irq_bitmask |= (search_mask >> 1) << pos; ++ break; ++ } ++ } ++ spin_unlock(&ifx_pcie_msi_lock); ++ ++ /* Make sure the search for available interrupts didn't fail */ ++ if (pos >= IFX_MSI_IRQ_NUM) { ++ if (request_private_bits) { ++ IFX_PCIE_PRINT(PCIE_MSG_MSI, "%s: Unable to find %d free " ++ "interrupts, trying just one", __func__, 1 << request_private_bits); ++ request_private_bits = 0; ++ goto again; ++ } ++ else { ++ printk(KERN_ERR "%s: Unable to find a free MSI interrupt\n", __func__); ++ return -EINVAL; ++ } ++ } ++ irq = msi_irqs[pcie_port].msi_irq_idx[pos].irq; ++ irq_idx = msi_irqs[pcie_port].msi_irq_idx[pos].idx; ++ ++ IFX_PCIE_PRINT(PCIE_MSG_MSI, "pos %d, irq %d irq_idx %d\n", pos, irq, irq_idx); ++ ++ /* ++ * Initialize MSI. This has to match the memory-write endianess from the device ++ * Address bits [23:12] ++ */ ++ spin_lock(&ifx_pcie_msi_lock); ++ msi_irqs[pcie_port].msi_pic_p->pic_table[pos] = SM(irq_idx, IFX_MSI_PIC_INT_LINE) | ++ SM((msi_irqs[pcie_port].msi_phy_base >> 12), IFX_MSI_PIC_MSG_ADDR) | ++ SM((1 << pos), IFX_MSI_PIC_MSG_DATA); ++ ++ /* Enable this entry */ ++ msi_irqs[pcie_port].msi_pic_p->pic_table[pos] &= ~IFX_MSI_PCI_INT_DISABLE; ++ spin_unlock(&ifx_pcie_msi_lock); ++ ++ IFX_PCIE_PRINT(PCIE_MSG_MSI, "pic_table[%d]: 0x%08x\n", ++ pos, msi_irqs[pcie_port].msi_pic_p->pic_table[pos]); ++ ++ /* Update the number of IRQs the device has available to it */ ++ control &= ~PCI_MSI_FLAGS_QSIZE; ++ control |= (request_private_bits << 4); ++ pci_write_config_word(pdev, desc->msi_attrib.pos + PCI_MSI_FLAGS, control); ++ ++ set_irq_msi(irq, desc); ++ msg.address_hi = 0x0; ++ msg.address_lo = msi_irqs[pcie_port].msi_phy_base; ++ msg.data = SM((1 << pos), IFX_MSI_PIC_MSG_DATA); ++ IFX_PCIE_PRINT(PCIE_MSG_MSI, "msi_data: pos %d 0x%08x\n", pos, msg.data); ++ ++ write_msi_msg(irq, &msg); ++ IFX_PCIE_PRINT(PCIE_MSG_MSI, "%s exit\n", __func__); ++ return 0; ++} ++ ++static int ++pcie_msi_irq_to_port(unsigned int irq, int *port) ++{ ++ int ret = 0; ++ ++ if (irq == IFX_PCIE_MSI_IR0 || irq == IFX_PCIE_MSI_IR1 || ++ irq == IFX_PCIE_MSI_IR2 || irq == IFX_PCIE_MSI_IR3) { ++ *port = IFX_PCIE_PORT0; ++ } ++#ifdef CONFIG_IFX_PCIE_2ND_CORE ++ else if (irq == IFX_PCIE1_MSI_IR0 || irq == IFX_PCIE1_MSI_IR1 || ++ irq == IFX_PCIE1_MSI_IR2 || irq == IFX_PCIE1_MSI_IR3) { ++ *port = IFX_PCIE_PORT1; ++ } ++#endif /* CONFIG_IFX_PCIE_2ND_CORE */ ++ else { ++ printk(KERN_ERR "%s: Attempted to teardown illegal " ++ "MSI interrupt (%d)\n", __func__, irq); ++ ret = -EINVAL; ++ } ++ return ret; ++} ++ ++/** ++ * \fn void arch_teardown_msi_irq(unsigned int irq) ++ * \brief Called when a device no longer needs its MSI interrupts. All ++ * MSI interrupts for the device are freed. ++ * ++ * \param irq The devices first irq number. There may be multple in sequence. ++ * \return none ++ * \ingroup IFX_PCIE_MSI ++ */ ++void ++arch_teardown_msi_irq(unsigned int irq) ++{ ++ int pos; ++ int number_irqs; ++ u16 bitmask; ++ int pcie_port; ++ ++ IFX_PCIE_PRINT(PCIE_MSG_MSI, "%s enter\n", __func__); ++ ++ BUG_ON(irq > INT_NUM_IM4_IRL31); ++ ++ if (pcie_msi_irq_to_port(irq, &pcie_port) != 0) { ++ return; ++ } ++ ++ /* Shift the mask to the correct bit location, not always correct ++ * Probally, the first match will be chosen. ++ */ ++ for (pos = 0; pos < IFX_MSI_IRQ_NUM; pos++) { ++ if ((msi_irqs[pcie_port].msi_irq_idx[pos].irq == irq) ++ && (msi_irqs[pcie_port].msi_free_irq_bitmask & ( 1 << pos))) { ++ break; ++ } ++ } ++ if (pos >= IFX_MSI_IRQ_NUM) { ++ printk(KERN_ERR "%s: Unable to find a matched MSI interrupt\n", __func__); ++ return; ++ } ++ spin_lock(&ifx_pcie_msi_lock); ++ /* Disable this entry */ ++ msi_irqs[pcie_port].msi_pic_p->pic_table[pos] |= IFX_MSI_PCI_INT_DISABLE; ++ msi_irqs[pcie_port].msi_pic_p->pic_table[pos] &= ~(IFX_MSI_PIC_INT_LINE | IFX_MSI_PIC_MSG_ADDR | IFX_MSI_PIC_MSG_DATA); ++ spin_unlock(&ifx_pcie_msi_lock); ++ /* ++ * Count the number of IRQs we need to free by looking at the ++ * msi_multiple_irq_bitmask. Each bit set means that the next ++ * IRQ is also owned by this device. ++ */ ++ number_irqs = 0; ++ while (((pos + number_irqs) < IFX_MSI_IRQ_NUM) && ++ (msi_irqs[pcie_port].msi_multiple_irq_bitmask & (1 << (pos + number_irqs)))) { ++ number_irqs++; ++ } ++ number_irqs++; ++ ++ /* Mask with one bit for each IRQ */ ++ bitmask = (1 << number_irqs) - 1; ++ ++ bitmask <<= pos; ++ if ((msi_irqs[pcie_port].msi_free_irq_bitmask & bitmask) != bitmask) { ++ printk(KERN_ERR "%s: Attempted to teardown MSI " ++ "interrupt (%d) not in use\n", __func__, irq); ++ return; ++ } ++ /* Checks are done, update the in use bitmask */ ++ spin_lock(&ifx_pcie_msi_lock); ++ msi_irqs[pcie_port].msi_free_irq_bitmask &= ~bitmask; ++ msi_irqs[pcie_port].msi_multiple_irq_bitmask &= ~(bitmask >> 1); ++ spin_unlock(&ifx_pcie_msi_lock); ++ IFX_PCIE_PRINT(PCIE_MSG_MSI, "%s exit\n", __func__); ++} ++ ++MODULE_LICENSE("GPL"); ++MODULE_AUTHOR("Chuanhua.Lei@infineon.com"); ++MODULE_SUPPORTED_DEVICE("Infineon PCIe IP builtin MSI PIC module"); ++MODULE_DESCRIPTION("Infineon PCIe IP builtin MSI PIC driver"); ++ +--- /dev/null ++++ b/arch/mips/pci/ifxmips_pcie_phy.c +@@ -0,0 +1,478 @@ ++/****************************************************************************** ++** ++** FILE NAME : ifxmips_pcie_phy.c ++** PROJECT : IFX UEIP for VRX200 ++** MODULES : PCIe PHY sub module ++** ++** DATE : 14 May 2009 ++** AUTHOR : Lei Chuanhua ++** DESCRIPTION : PCIe Root Complex Driver ++** COPYRIGHT : Copyright (c) 2009 ++** Infineon Technologies AG ++** Am Campeon 1-12, 85579 Neubiberg, Germany ++** ++** This program is free software; you can redistribute it and/or modify ++** it under the terms of the GNU General Public License as published by ++** the Free Software Foundation; either version 2 of the License, or ++** (at your option) any later version. ++** HISTORY ++** $Version $Date $Author $Comment ++** 0.0.1 14 May,2009 Lei Chuanhua Initial version ++*******************************************************************************/ ++/*! ++ \file ifxmips_pcie_phy.c ++ \ingroup IFX_PCIE ++ \brief PCIe PHY PLL register programming source file ++*/ ++#include ++#include ++#include ++#include ++ ++#include "ifxmips_pcie_reg.h" ++#include "ifxmips_pcie.h" ++ ++/* PCIe PDI only supports 16 bit operation */ ++ ++#define IFX_PCIE_PHY_REG_WRITE16(__addr, __data) \ ++ ((*(volatile u16 *) (__addr)) = (__data)) ++ ++#define IFX_PCIE_PHY_REG_READ16(__addr) \ ++ (*(volatile u16 *) (__addr)) ++ ++#define IFX_PCIE_PHY_REG16(__addr) \ ++ (*(volatile u16 *) (__addr)) ++ ++#define IFX_PCIE_PHY_REG(__reg, __value, __mask) do { \ ++ u16 read_data; \ ++ u16 write_data; \ ++ read_data = IFX_PCIE_PHY_REG_READ16((__reg)); \ ++ write_data = (read_data & ((u16)~(__mask))) | (((u16)(__value)) & ((u16)(__mask)));\ ++ IFX_PCIE_PHY_REG_WRITE16((__reg), write_data); \ ++} while (0) ++ ++#define IFX_PCIE_PLL_TIMEOUT 1000 /* Tunnable */ ++ ++//#define IFX_PCI_PHY_REG_DUMP ++ ++#ifdef IFX_PCI_PHY_REG_DUMP ++static void ++pcie_phy_reg_dump(int pcie_port) ++{ ++ printk("PLL REGFILE\n"); ++ printk("PCIE_PHY_PLL_CTRL1 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_PLL_CTRL1(pcie_port))); ++ printk("PCIE_PHY_PLL_CTRL2 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_PLL_CTRL2(pcie_port))); ++ printk("PCIE_PHY_PLL_CTRL3 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_PLL_CTRL3(pcie_port))); ++ printk("PCIE_PHY_PLL_CTRL4 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_PLL_CTRL4(pcie_port))); ++ printk("PCIE_PHY_PLL_CTRL5 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_PLL_CTRL5(pcie_port))); ++ printk("PCIE_PHY_PLL_CTRL6 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_PLL_CTRL6(pcie_port))); ++ printk("PCIE_PHY_PLL_CTRL7 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_PLL_CTRL7(pcie_port))); ++ printk("PCIE_PHY_PLL_A_CTRL1 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_PLL_A_CTRL1(pcie_port))); ++ printk("PCIE_PHY_PLL_A_CTRL2 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_PLL_A_CTRL2(pcie_port))); ++ printk("PCIE_PHY_PLL_A_CTRL3 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_PLL_A_CTRL3(pcie_port))); ++ printk("PCIE_PHY_PLL_STATUS 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_PLL_STATUS(pcie_port))); ++ ++ printk("TX1 REGFILE\n"); ++ printk("PCIE_PHY_TX1_CTRL1 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_TX1_CTRL1(pcie_port))); ++ printk("PCIE_PHY_TX1_CTRL2 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_TX1_CTRL2(pcie_port))); ++ printk("PCIE_PHY_TX1_CTRL3 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_TX1_CTRL3(pcie_port))); ++ printk("PCIE_PHY_TX1_A_CTRL1 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_TX1_A_CTRL1(pcie_port))); ++ printk("PCIE_PHY_TX1_A_CTRL2 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_TX1_A_CTRL2(pcie_port))); ++ printk("PCIE_PHY_TX1_MOD1 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_TX1_MOD1(pcie_port))); ++ printk("PCIE_PHY_TX1_MOD2 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_TX1_MOD2(pcie_port))); ++ printk("PCIE_PHY_TX1_MOD3 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_TX1_MOD3(pcie_port))); ++ ++ printk("TX2 REGFILE\n"); ++ printk("PCIE_PHY_TX2_CTRL1 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_TX2_CTRL1(pcie_port))); ++ printk("PCIE_PHY_TX2_CTRL2 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_TX2_CTRL2(pcie_port))); ++ printk("PCIE_PHY_TX2_A_CTRL1 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_TX2_A_CTRL1(pcie_port))); ++ printk("PCIE_PHY_TX2_A_CTRL2 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_TX2_A_CTRL2(pcie_port))); ++ printk("PCIE_PHY_TX2_MOD1 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_TX2_MOD1(pcie_port))); ++ printk("PCIE_PHY_TX2_MOD2 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_TX2_MOD2(pcie_port))); ++ printk("PCIE_PHY_TX2_MOD3 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_TX2_MOD3(pcie_port))); ++ ++ printk("RX1 REGFILE\n"); ++ printk("PCIE_PHY_RX1_CTRL1 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_RX1_CTRL1(pcie_port))); ++ printk("PCIE_PHY_RX1_CTRL2 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_RX1_CTRL2(pcie_port))); ++ printk("PCIE_PHY_RX1_CDR 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_RX1_CDR(pcie_port))); ++ printk("PCIE_PHY_RX1_EI 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_RX1_EI(pcie_port))); ++ printk("PCIE_PHY_RX1_A_CTRL 0x%04x\n", IFX_PCIE_PHY_REG16(PCIE_PHY_RX1_A_CTRL(pcie_port))); ++} ++#endif /* IFX_PCI_PHY_REG_DUMP */ ++ ++static void ++pcie_phy_comm_setup(int pcie_port) ++{ ++ /* PLL Setting */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_A_CTRL1(pcie_port), 0x120e, 0xFFFF); ++ ++ /* increase the bias reference voltage */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_A_CTRL2(pcie_port), 0x39D7, 0xFFFF); ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_A_CTRL3(pcie_port), 0x0900, 0xFFFF); ++ ++ /* Endcnt */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_RX1_EI(pcie_port), 0x0004, 0xFFFF); ++ IFX_PCIE_PHY_REG(PCIE_PHY_RX1_A_CTRL(pcie_port), 0x6803, 0xFFFF); ++ ++ /* force */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_TX1_CTRL1(pcie_port), 0x0008, 0x0008); ++ ++ /* predrv_ser_en */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_TX1_A_CTRL2(pcie_port), 0x0706, 0xFFFF); ++ ++ /* ctrl_lim */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_TX1_CTRL3(pcie_port), 0x1FFF, 0xFFFF); ++ ++ /* ctrl */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_TX1_A_CTRL1(pcie_port), 0x0800, 0xFF00); ++ ++ /* predrv_ser_en */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_TX2_A_CTRL2(pcie_port), 0x4702, 0x7F00); ++ ++ /* RTERM*/ ++ IFX_PCIE_PHY_REG(PCIE_PHY_TX1_CTRL2(pcie_port), 0x2e00, 0xFFFF); ++ ++ /* Improved 100MHz clock output */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_TX2_CTRL2(pcie_port), 0x3096, 0xFFFF); ++ IFX_PCIE_PHY_REG(PCIE_PHY_TX2_A_CTRL2(pcie_port), 0x4707, 0xFFFF); ++ ++ /* Reduced CDR BW to avoid glitches */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_RX1_CDR(pcie_port), 0x0235, 0xFFFF); ++} ++ ++#ifdef CONFIG_IFX_PCIE_PHY_36MHZ_MODE ++static void ++pcie_phy_36mhz_mode_setup(int pcie_port) ++{ ++ IFX_PCIE_PRINT(PCIE_MSG_PHY, "%s pcie_port %d enter\n", __func__, pcie_port); ++#ifdef IFX_PCI_PHY_REG_DUMP ++ IFX_PCIE_PRINT(PCIE_MSG_PHY, "Initial PHY register dump\n"); ++ pcie_phy_reg_dump(pcie_port); ++#endif ++ ++ /* en_ext_mmd_div_ratio */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL3(pcie_port), 0x0000, 0x0002); ++ ++ /* ext_mmd_div_ratio*/ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL3(pcie_port), 0x0000, 0x0070); ++ ++ /* pll_ensdm */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL2(pcie_port), 0x0200, 0x0200); ++ ++ /* en_const_sdm */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL2(pcie_port), 0x0100, 0x0100); ++ ++ /* mmd */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_A_CTRL3(pcie_port), 0x2000, 0xe000); ++ ++ /* lf_mode */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_A_CTRL2(pcie_port), 0x0000, 0x4000); ++ ++ /* const_sdm */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL1(pcie_port), 0x38e4, 0xFFFF); ++ ++ /* const sdm */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL2(pcie_port), 0x00ee, 0x00FF); ++ ++ /* pllmod */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL7(pcie_port), 0x0002, 0xFFFF); ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL6(pcie_port), 0x3a04, 0xFFFF); ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL5(pcie_port), 0xfae3, 0xFFFF); ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL4(pcie_port), 0x1b72, 0xFFFF); ++ ++ IFX_PCIE_PRINT(PCIE_MSG_PHY, "%s pcie_port %d exit\n", __func__, pcie_port); ++} ++#endif /* CONFIG_IFX_PCIE_PHY_36MHZ_MODE */ ++ ++#ifdef CONFIG_IFX_PCIE_PHY_36MHZ_SSC_MODE ++static void ++pcie_phy_36mhz_ssc_mode_setup(int pcie_port) ++{ ++ IFX_PCIE_PRINT(PCIE_MSG_PHY, "%s pcie_port %d enter\n", __func__, pcie_port); ++#ifdef IFX_PCI_PHY_REG_DUMP ++ IFX_PCIE_PRINT(PCIE_MSG_PHY, "Initial PHY register dump\n"); ++ pcie_phy_reg_dump(pcie_port); ++#endif ++ ++ /* PLL Setting */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_A_CTRL1(pcie_port), 0x120e, 0xFFFF); ++ ++ /* Increase the bias reference voltage */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_A_CTRL2(pcie_port), 0x39D7, 0xFFFF); ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_A_CTRL3(pcie_port), 0x0900, 0xFFFF); ++ ++ /* Endcnt */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_RX1_EI(pcie_port), 0x0004, 0xFFFF); ++ IFX_PCIE_PHY_REG(PCIE_PHY_RX1_A_CTRL(pcie_port), 0x6803, 0xFFFF); ++ ++ /* Force */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_TX1_CTRL1(pcie_port), 0x0008, 0x0008); ++ ++ /* Predrv_ser_en */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_TX1_A_CTRL2(pcie_port), 0x0706, 0xFFFF); ++ ++ /* ctrl_lim */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_TX1_CTRL3(pcie_port), 0x1FFF, 0xFFFF); ++ ++ /* ctrl */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_TX1_A_CTRL1(pcie_port), 0x0800, 0xFF00); ++ ++ /* predrv_ser_en */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_TX2_A_CTRL2(pcie_port), 0x4702, 0x7F00); ++ ++ /* RTERM*/ ++ IFX_PCIE_PHY_REG(PCIE_PHY_TX1_CTRL2(pcie_port), 0x2e00, 0xFFFF); ++ ++ /* en_ext_mmd_div_ratio */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL3(pcie_port), 0x0000, 0x0002); ++ ++ /* ext_mmd_div_ratio*/ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL3(pcie_port), 0x0000, 0x0070); ++ ++ /* pll_ensdm */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL2(pcie_port), 0x0400, 0x0400); ++ ++ /* en_const_sdm */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL2(pcie_port), 0x0200, 0x0200); ++ ++ /* mmd */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_A_CTRL3(pcie_port), 0x2000, 0xe000); ++ ++ /* lf_mode */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_A_CTRL2(pcie_port), 0x0000, 0x4000); ++ ++ /* const_sdm */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL1(pcie_port), 0x38e4, 0xFFFF); ++ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL2(pcie_port), 0x0000, 0x0100); ++ /* const sdm */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL2(pcie_port), 0x00ee, 0x00FF); ++ ++ /* pllmod */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL7(pcie_port), 0x0002, 0xFFFF); ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL6(pcie_port), 0x3a04, 0xFFFF); ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL5(pcie_port), 0xfae3, 0xFFFF); ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL4(pcie_port), 0x1c72, 0xFFFF); ++ ++ /* improved 100MHz clock output */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_TX2_CTRL2(pcie_port), 0x3096, 0xFFFF); ++ IFX_PCIE_PHY_REG(PCIE_PHY_TX2_A_CTRL2(pcie_port), 0x4707, 0xFFFF); ++ ++ /* reduced CDR BW to avoid glitches */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_RX1_CDR(pcie_port), 0x0235, 0xFFFF); ++ ++ IFX_PCIE_PRINT(PCIE_MSG_PHY, "%s pcie_port %d exit\n", __func__, pcie_port); ++} ++#endif /* CONFIG_IFX_PCIE_PHY_36MHZ_SSC_MODE */ ++ ++#ifdef CONFIG_IFX_PCIE_PHY_25MHZ_MODE ++static void ++pcie_phy_25mhz_mode_setup(int pcie_port) ++{ ++ IFX_PCIE_PRINT(PCIE_MSG_PHY, "%s pcie_port %d enter\n", __func__, pcie_port); ++#ifdef IFX_PCI_PHY_REG_DUMP ++ IFX_PCIE_PRINT(PCIE_MSG_PHY, "Initial PHY register dump\n"); ++ pcie_phy_reg_dump(pcie_port); ++#endif ++ /* en_const_sdm */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL2(pcie_port), 0x0100, 0x0100); ++ ++ /* pll_ensdm */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL2(pcie_port), 0x0000, 0x0200); ++ ++ /* en_ext_mmd_div_ratio*/ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL3(pcie_port), 0x0002, 0x0002); ++ ++ /* ext_mmd_div_ratio*/ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL3(pcie_port), 0x0040, 0x0070); ++ ++ /* mmd */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_A_CTRL3(pcie_port), 0x6000, 0xe000); ++ ++ /* lf_mode */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_A_CTRL2(pcie_port), 0x4000, 0x4000); ++ ++ IFX_PCIE_PRINT(PCIE_MSG_PHY, "%s pcie_port %d exit\n", __func__, pcie_port); ++} ++#endif /* CONFIG_IFX_PCIE_PHY_25MHZ_MODE */ ++ ++#ifdef CONFIG_IFX_PCIE_PHY_100MHZ_MODE ++static void ++pcie_phy_100mhz_mode_setup(int pcie_port) ++{ ++ IFX_PCIE_PRINT(PCIE_MSG_PHY, "%s pcie_port %d enter\n", __func__, pcie_port); ++#ifdef IFX_PCI_PHY_REG_DUMP ++ IFX_PCIE_PRINT(PCIE_MSG_PHY, "Initial PHY register dump\n"); ++ pcie_phy_reg_dump(pcie_port); ++#endif ++ /* en_ext_mmd_div_ratio */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL3(pcie_port), 0x0000, 0x0002); ++ ++ /* ext_mmd_div_ratio*/ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL3(pcie_port), 0x0000, 0x0070); ++ ++ /* pll_ensdm */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL2(pcie_port), 0x0200, 0x0200); ++ ++ /* en_const_sdm */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL2(pcie_port), 0x0100, 0x0100); ++ ++ /* mmd */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_A_CTRL3(pcie_port), 0x2000, 0xe000); ++ ++ /* lf_mode */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_A_CTRL2(pcie_port), 0x0000, 0x4000); ++ ++ /* const_sdm */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL1(pcie_port), 0x38e4, 0xFFFF); ++ ++ /* const sdm */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL2(pcie_port), 0x00ee, 0x00FF); ++ ++ /* pllmod */ ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL7(pcie_port), 0x0002, 0xFFFF); ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL6(pcie_port), 0x3a04, 0xFFFF); ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL5(pcie_port), 0xfae3, 0xFFFF); ++ IFX_PCIE_PHY_REG(PCIE_PHY_PLL_CTRL4(pcie_port), 0x1b72, 0xFFFF); ++ ++ IFX_PCIE_PRINT(PCIE_MSG_PHY, "%s pcie_port %d exit\n", __func__, pcie_port); ++} ++#endif /* CONFIG_IFX_PCIE_PHY_100MHZ_MODE */ ++ ++static int ++pcie_phy_wait_startup_ready(int pcie_port) ++{ ++ int i; ++ ++ for (i = 0; i < IFX_PCIE_PLL_TIMEOUT; i++) { ++ if ((IFX_PCIE_PHY_REG16(PCIE_PHY_PLL_STATUS(pcie_port)) & 0x0040) != 0) { ++ break; ++ } ++ udelay(10); ++ } ++ if (i >= IFX_PCIE_PLL_TIMEOUT) { ++ printk(KERN_ERR "%s PLL Link timeout\n", __func__); ++ return -1; ++ } ++ return 0; ++} ++ ++static void ++pcie_phy_load_enable(int pcie_port, int slice) ++{ ++ /* Set the load_en of tx/rx slice to '1' */ ++ switch (slice) { ++ case 1: ++ IFX_PCIE_PHY_REG(PCIE_PHY_TX1_CTRL1(pcie_port), 0x0010, 0x0010); ++ break; ++ case 2: ++ IFX_PCIE_PHY_REG(PCIE_PHY_TX2_CTRL1(pcie_port), 0x0010, 0x0010); ++ break; ++ case 3: ++ IFX_PCIE_PHY_REG(PCIE_PHY_RX1_CTRL1(pcie_port), 0x0002, 0x0002); ++ break; ++ } ++} ++ ++static void ++pcie_phy_load_disable(int pcie_port, int slice) ++{ ++ /* set the load_en of tx/rx slice to '0' */ ++ switch (slice) { ++ case 1: ++ IFX_PCIE_PHY_REG(PCIE_PHY_TX1_CTRL1(pcie_port), 0x0000, 0x0010); ++ break; ++ case 2: ++ IFX_PCIE_PHY_REG(PCIE_PHY_TX2_CTRL1(pcie_port), 0x0000, 0x0010); ++ break; ++ case 3: ++ IFX_PCIE_PHY_REG(PCIE_PHY_RX1_CTRL1(pcie_port), 0x0000, 0x0002); ++ break; ++ } ++} ++ ++static void ++pcie_phy_load_war(int pcie_port) ++{ ++ int slice; ++ ++ for (slice = 1; slice < 4; slice++) { ++ pcie_phy_load_enable(pcie_port, slice); ++ udelay(1); ++ pcie_phy_load_disable(pcie_port, slice); ++ } ++} ++ ++static void ++pcie_phy_tx2_modulation(int pcie_port) ++{ ++ IFX_PCIE_PHY_REG(PCIE_PHY_TX2_MOD1(pcie_port), 0x1FFE, 0xFFFF); ++ IFX_PCIE_PHY_REG(PCIE_PHY_TX2_MOD2(pcie_port), 0xFFFE, 0xFFFF); ++ IFX_PCIE_PHY_REG(PCIE_PHY_TX2_MOD3(pcie_port), 0x0601, 0xFFFF); ++ mdelay(1); ++ IFX_PCIE_PHY_REG(PCIE_PHY_TX2_MOD3(pcie_port), 0x0001, 0xFFFF); ++} ++ ++static void ++pcie_phy_tx1_modulation(int pcie_port) ++{ ++ IFX_PCIE_PHY_REG(PCIE_PHY_TX1_MOD1(pcie_port), 0x1FFE, 0xFFFF); ++ IFX_PCIE_PHY_REG(PCIE_PHY_TX1_MOD2(pcie_port), 0xFFFE, 0xFFFF); ++ IFX_PCIE_PHY_REG(PCIE_PHY_TX1_MOD3(pcie_port), 0x0601, 0xFFFF); ++ mdelay(1); ++ IFX_PCIE_PHY_REG(PCIE_PHY_TX1_MOD3(pcie_port), 0x0001, 0xFFFF); ++} ++ ++static void ++pcie_phy_tx_modulation_war(int pcie_port) ++{ ++ int i; ++ ++#define PCIE_PHY_MODULATION_NUM 5 ++ for (i = 0; i < PCIE_PHY_MODULATION_NUM; i++) { ++ pcie_phy_tx2_modulation(pcie_port); ++ pcie_phy_tx1_modulation(pcie_port); ++ } ++#undef PCIE_PHY_MODULATION_NUM ++} ++ ++void ++pcie_phy_clock_mode_setup(int pcie_port) ++{ ++ pcie_pdi_big_endian(pcie_port); ++ ++ /* Enable PDI to access PCIe PHY register */ ++ pcie_pdi_pmu_enable(pcie_port); ++ ++ /* Configure PLL and PHY clock */ ++ pcie_phy_comm_setup(pcie_port); ++ ++#ifdef CONFIG_IFX_PCIE_PHY_36MHZ_MODE ++ pcie_phy_36mhz_mode_setup(pcie_port); ++#elif defined(CONFIG_IFX_PCIE_PHY_36MHZ_SSC_MODE) ++ pcie_phy_36mhz_ssc_mode_setup(pcie_port); ++#elif defined(CONFIG_IFX_PCIE_PHY_25MHZ_MODE) ++ pcie_phy_25mhz_mode_setup(pcie_port); ++#elif defined (CONFIG_IFX_PCIE_PHY_100MHZ_MODE) ++ pcie_phy_100mhz_mode_setup(pcie_port); ++#else ++ #error "PCIE PHY Clock Mode must be chosen first!!!!" ++#endif /* CONFIG_IFX_PCIE_PHY_36MHZ_MODE */ ++ ++ /* Enable PCIe PHY and make PLL setting take effect */ ++ pcie_phy_pmu_enable(pcie_port); ++ ++ /* Check if we are in startup_ready status */ ++ pcie_phy_wait_startup_ready(pcie_port); ++ ++ pcie_phy_load_war(pcie_port); ++ ++ /* Apply TX modulation workarounds */ ++ pcie_phy_tx_modulation_war(pcie_port); ++ ++#ifdef IFX_PCI_PHY_REG_DUMP ++ IFX_PCIE_PRINT(PCIE_MSG_PHY, "Modified PHY register dump\n"); ++ pcie_phy_reg_dump(pcie_port); ++#endif ++} ++ +--- /dev/null ++++ b/arch/mips/pci/ifxmips_pcie_pm.c +@@ -0,0 +1,176 @@ ++/****************************************************************************** ++** ++** FILE NAME : ifxmips_pcie_pm.c ++** PROJECT : IFX UEIP ++** MODULES : PCIE Root Complex Driver ++** ++** DATE : 21 Dec 2009 ++** AUTHOR : Lei Chuanhua ++** DESCRIPTION : PCIE Root Complex Driver Power Managment ++** COPYRIGHT : Copyright (c) 2009 ++** Lantiq Deutschland GmbH ++** Am Campeon 3, 85579 Neubiberg, Germany ++** ++** This program is free software; you can redistribute it and/or modify ++** it under the terms of the GNU General Public License as published by ++** the Free Software Foundation; either version 2 of the License, or ++** (at your option) any later version. ++** ++** HISTORY ++** $Date $Author $Comment ++** 21 Dec,2009 Lei Chuanhua First UEIP release ++*******************************************************************************/ ++/*! ++ \defgroup IFX_PCIE_PM Power Management functions ++ \ingroup IFX_PCIE ++ \brief IFX PCIE Root Complex Driver power management functions ++*/ ++ ++/*! ++ \file ifxmips_pcie_pm.c ++ \ingroup IFX_PCIE ++ \brief source file for PCIE Root Complex Driver Power Management ++*/ ++ ++#ifndef EXPORT_SYMTAB ++#define EXPORT_SYMTAB ++#endif ++#ifndef AUTOCONF_INCLUDED ++#include ++#endif /* AUTOCONF_INCLUDED */ ++#include ++#include ++#include ++#include ++#include ++ ++/* Project header */ ++#include ++#include ++#include ++#include ++#include "ifxmips_pcie_pm.h" ++ ++/** ++ * \fn static IFX_PMCU_RETURN_t ifx_pcie_pmcu_state_change(IFX_PMCU_STATE_t pmcuState) ++ * \brief the callback function to request pmcu state in the power management hardware-dependent module ++ * ++ * \param pmcuState This parameter is a PMCU state. ++ * ++ * \return IFX_PMCU_RETURN_SUCCESS Set Power State successfully ++ * \return IFX_PMCU_RETURN_ERROR Failed to set power state. ++ * \return IFX_PMCU_RETURN_DENIED Not allowed to operate power state ++ * \ingroup IFX_PCIE_PM ++ */ ++static IFX_PMCU_RETURN_t ++ifx_pcie_pmcu_state_change(IFX_PMCU_STATE_t pmcuState) ++{ ++ switch(pmcuState) ++ { ++ case IFX_PMCU_STATE_D0: ++ return IFX_PMCU_RETURN_SUCCESS; ++ case IFX_PMCU_STATE_D1: // Not Applicable ++ return IFX_PMCU_RETURN_DENIED; ++ case IFX_PMCU_STATE_D2: // Not Applicable ++ return IFX_PMCU_RETURN_DENIED; ++ case IFX_PMCU_STATE_D3: // Module clock gating and Power gating ++ return IFX_PMCU_RETURN_SUCCESS; ++ default: ++ return IFX_PMCU_RETURN_DENIED; ++ } ++} ++ ++/** ++ * \fn static IFX_PMCU_RETURN_t ifx_pcie_pmcu_state_get(IFX_PMCU_STATE_t *pmcuState) ++ * \brief the callback function to get pmcu state in the power management hardware-dependent module ++ ++ * \param pmcuState Pointer to return power state. ++ * ++ * \return IFX_PMCU_RETURN_SUCCESS Set Power State successfully ++ * \return IFX_PMCU_RETURN_ERROR Failed to set power state. ++ * \return IFX_PMCU_RETURN_DENIED Not allowed to operate power state ++ * \ingroup IFX_PCIE_PM ++ */ ++static IFX_PMCU_RETURN_t ++ifx_pcie_pmcu_state_get(IFX_PMCU_STATE_t *pmcuState) ++{ ++ return IFX_PMCU_RETURN_SUCCESS; ++} ++ ++/** ++ * \fn IFX_PMCU_RETURN_t ifx_pcie_pmcu_prechange(IFX_PMCU_MODULE_t pmcuModule, IFX_PMCU_STATE_t newState, IFX_PMCU_STATE_t oldState) ++ * \brief Apply all callbacks registered to be executed before a state change for pmcuModule ++ * ++ * \param pmcuModule Module ++ * \param newState New state ++ * \param oldState Old state ++ * \return IFX_PMCU_RETURN_SUCCESS Set Power State successfully ++ * \return IFX_PMCU_RETURN_ERROR Failed to set power state. ++ * \ingroup IFX_PCIE_PM ++ */ ++static IFX_PMCU_RETURN_t ++ifx_pcie_pmcu_prechange(IFX_PMCU_MODULE_t pmcuModule, IFX_PMCU_STATE_t newState, IFX_PMCU_STATE_t oldState) ++{ ++ return IFX_PMCU_RETURN_SUCCESS; ++} ++ ++/** ++ * \fn IFX_PMCU_RETURN_t ifx_pcie_pmcu_postchange(IFX_PMCU_MODULE_t pmcuModule, IFX_PMCU_STATE_t newState, IFX_PMCU_STATE_t oldState) ++ * \brief Apply all callbacks registered to be executed before a state change for pmcuModule ++ * ++ * \param pmcuModule Module ++ * \param newState New state ++ * \param oldState Old state ++ * \return IFX_PMCU_RETURN_SUCCESS Set Power State successfully ++ * \return IFX_PMCU_RETURN_ERROR Failed to set power state. ++ * \ingroup IFX_PCIE_PM ++ */ ++static IFX_PMCU_RETURN_t ++ifx_pcie_pmcu_postchange(IFX_PMCU_MODULE_t pmcuModule, IFX_PMCU_STATE_t newState, IFX_PMCU_STATE_t oldState) ++{ ++ return IFX_PMCU_RETURN_SUCCESS; ++} ++ ++/** ++ * \fn static void ifx_pcie_pmcu_init(void) ++ * \brief Register with central PMCU module ++ * \return none ++ * \ingroup IFX_PCIE_PM ++ */ ++void ++ifx_pcie_pmcu_init(void) ++{ ++ IFX_PMCU_REGISTER_t pmcuRegister; ++ ++ /* XXX, hook driver context */ ++ ++ /* State function register */ ++ memset(&pmcuRegister, 0, sizeof(IFX_PMCU_REGISTER_t)); ++ pmcuRegister.pmcuModule = IFX_PMCU_MODULE_PCIE; ++ pmcuRegister.pmcuModuleNr = 0; ++ pmcuRegister.ifx_pmcu_state_change = ifx_pcie_pmcu_state_change; ++ pmcuRegister.ifx_pmcu_state_get = ifx_pcie_pmcu_state_get; ++ pmcuRegister.pre = ifx_pcie_pmcu_prechange; ++ pmcuRegister.post= ifx_pcie_pmcu_postchange; ++ ifx_pmcu_register(&pmcuRegister); ++} ++ ++/** ++ * \fn static void ifx_pcie_pmcu_exit(void) ++ * \brief Unregister with central PMCU module ++ * ++ * \return none ++ * \ingroup IFX_PCIE_PM ++ */ ++void ++ifx_pcie_pmcu_exit(void) ++{ ++ IFX_PMCU_REGISTER_t pmcuUnRegister; ++ ++ /* XXX, hook driver context */ ++ ++ pmcuUnRegister.pmcuModule = IFX_PMCU_MODULE_PCIE; ++ pmcuUnRegister.pmcuModuleNr = 0; ++ ifx_pmcu_unregister(&pmcuUnRegister); ++} ++ +--- /dev/null ++++ b/arch/mips/pci/ifxmips_pcie_pm.h +@@ -0,0 +1,36 @@ ++/****************************************************************************** ++** ++** FILE NAME : ifxmips_pcie_pm.h ++** PROJECT : IFX UEIP ++** MODULES : PCIe Root Complex Driver ++** ++** DATE : 21 Dec 2009 ++** AUTHOR : Lei Chuanhua ++** DESCRIPTION : PCIe Root Complex Driver Power Managment ++** COPYRIGHT : Copyright (c) 2009 ++** Lantiq Deutschland GmbH ++** Am Campeon 3, 85579 Neubiberg, Germany ++** ++** This program is free software; you can redistribute it and/or modify ++** it under the terms of the GNU General Public License as published by ++** the Free Software Foundation; either version 2 of the License, or ++** (at your option) any later version. ++** ++** HISTORY ++** $Date $Author $Comment ++** 21 Dec,2009 Lei Chuanhua First UEIP release ++*******************************************************************************/ ++/*! ++ \file ifxmips_pcie_pm.h ++ \ingroup IFX_PCIE ++ \brief header file for PCIe Root Complex Driver Power Management ++*/ ++ ++#ifndef IFXMIPS_PCIE_PM_H ++#define IFXMIPS_PCIE_PM_H ++ ++void ifx_pcie_pmcu_init(void); ++void ifx_pcie_pmcu_exit(void); ++ ++#endif /* IFXMIPS_PCIE_PM_H */ ++ +--- /dev/null ++++ b/arch/mips/pci/ifxmips_pcie_reg.h +@@ -0,0 +1,1001 @@ ++/****************************************************************************** ++** ++** FILE NAME : ifxmips_pcie_reg.h ++** PROJECT : IFX UEIP for VRX200 ++** MODULES : PCIe module ++** ++** DATE : 02 Mar 2009 ++** AUTHOR : Lei Chuanhua ++** DESCRIPTION : PCIe Root Complex Driver ++** COPYRIGHT : Copyright (c) 2009 ++** Infineon Technologies AG ++** Am Campeon 1-12, 85579 Neubiberg, Germany ++** ++** This program is free software; you can redistribute it and/or modify ++** it under the terms of the GNU General Public License as published by ++** the Free Software Foundation; either version 2 of the License, or ++** (at your option) any later version. ++** HISTORY ++** $Version $Date $Author $Comment ++** 0.0.1 17 Mar,2009 Lei Chuanhua Initial version ++*******************************************************************************/ ++#ifndef IFXMIPS_PCIE_REG_H ++#define IFXMIPS_PCIE_REG_H ++/*! ++ \file ifxmips_pcie_reg.h ++ \ingroup IFX_PCIE ++ \brief header file for PCIe module register definition ++*/ ++/* PCIe Address Mapping Base */ ++#define PCIE_CFG_PHY_BASE 0x1D000000UL ++#define PCIE_CFG_BASE (KSEG1 + PCIE_CFG_PHY_BASE) ++#define PCIE_CFG_SIZE (8 * 1024 * 1024) ++ ++#define PCIE_MEM_PHY_BASE 0x1C000000UL ++#define PCIE_MEM_BASE (KSEG1 + PCIE_MEM_PHY_BASE) ++#define PCIE_MEM_SIZE (16 * 1024 * 1024) ++#define PCIE_MEM_PHY_END (PCIE_MEM_PHY_BASE + PCIE_MEM_SIZE - 1) ++ ++#define PCIE_IO_PHY_BASE 0x1D800000UL ++#define PCIE_IO_BASE (KSEG1 + PCIE_IO_PHY_BASE) ++#define PCIE_IO_SIZE (1 * 1024 * 1024) ++#define PCIE_IO_PHY_END (PCIE_IO_PHY_BASE + PCIE_IO_SIZE - 1) ++ ++#define PCIE_RC_CFG_BASE (KSEG1 + 0x1D900000) ++#define PCIE_APP_LOGIC_REG (KSEG1 + 0x1E100900) ++#define PCIE_MSI_PHY_BASE 0x1F600000UL ++ ++#define PCIE_PDI_PHY_BASE 0x1F106800UL ++#define PCIE_PDI_BASE (KSEG1 + PCIE_PDI_PHY_BASE) ++#define PCIE_PDI_SIZE 0x400 ++ ++#define PCIE1_CFG_PHY_BASE 0x19000000UL ++#define PCIE1_CFG_BASE (KSEG1 + PCIE1_CFG_PHY_BASE) ++#define PCIE1_CFG_SIZE (8 * 1024 * 1024) ++ ++#define PCIE1_MEM_PHY_BASE 0x18000000UL ++#define PCIE1_MEM_BASE (KSEG1 + PCIE1_MEM_PHY_BASE) ++#define PCIE1_MEM_SIZE (16 * 1024 * 1024) ++#define PCIE1_MEM_PHY_END (PCIE1_MEM_PHY_BASE + PCIE1_MEM_SIZE - 1) ++ ++#define PCIE1_IO_PHY_BASE 0x19800000UL ++#define PCIE1_IO_BASE (KSEG1 + PCIE1_IO_PHY_BASE) ++#define PCIE1_IO_SIZE (1 * 1024 * 1024) ++#define PCIE1_IO_PHY_END (PCIE1_IO_PHY_BASE + PCIE1_IO_SIZE - 1) ++ ++#define PCIE1_RC_CFG_BASE (KSEG1 + 0x19900000) ++#define PCIE1_APP_LOGIC_REG (KSEG1 + 0x1E100700) ++#define PCIE1_MSI_PHY_BASE 0x1F400000UL ++ ++#define PCIE1_PDI_PHY_BASE 0x1F700400UL ++#define PCIE1_PDI_BASE (KSEG1 + PCIE1_PDI_PHY_BASE) ++#define PCIE1_PDI_SIZE 0x400 ++ ++#define PCIE_CFG_PORT_TO_BASE(X) ((X) > 0 ? (PCIE1_CFG_BASE) : (PCIE_CFG_BASE)) ++#define PCIE_MEM_PORT_TO_BASE(X) ((X) > 0 ? (PCIE1_MEM_BASE) : (PCIE_MEM_BASE)) ++#define PCIE_IO_PORT_TO_BASE(X) ((X) > 0 ? (PCIE1_IO_BASE) : (PCIE_IO_BASE)) ++#define PCIE_MEM_PHY_PORT_TO_BASE(X) ((X) > 0 ? (PCIE1_MEM_PHY_BASE) : (PCIE_MEM_PHY_BASE)) ++#define PCIE_MEM_PHY_PORT_TO_END(X) ((X) > 0 ? (PCIE1_MEM_PHY_END) : (PCIE_MEM_PHY_END)) ++#define PCIE_IO_PHY_PORT_TO_BASE(X) ((X) > 0 ? (PCIE1_IO_PHY_BASE) : (PCIE_IO_PHY_BASE)) ++#define PCIE_IO_PHY_PORT_TO_END(X) ((X) > 0 ? (PCIE1_IO_PHY_END) : (PCIE_IO_PHY_END)) ++#define PCIE_APP_PORT_TO_BASE(X) ((X) > 0 ? (PCIE1_APP_LOGIC_REG) : (PCIE_APP_LOGIC_REG)) ++#define PCIE_RC_PORT_TO_BASE(X) ((X) > 0 ? (PCIE1_RC_CFG_BASE) : (PCIE_RC_CFG_BASE)) ++#define PCIE_PHY_PORT_TO_BASE(X) ((X) > 0 ? (PCIE1_PDI_BASE) : (PCIE_PDI_BASE)) ++ ++/* PCIe Application Logic Register */ ++/* RC Core Control Register */ ++#define PCIE_RC_CCR(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x10) ++/* This should be enabled after initializing configuratin registers ++ * Also should check link status retraining bit ++ */ ++#define PCIE_RC_CCR_LTSSM_ENABLE 0x00000001 /* Enable LTSSM to continue link establishment */ ++ ++/* RC Core Debug Register */ ++#define PCIE_RC_DR(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x14) ++#define PCIE_RC_DR_DLL_UP 0x00000001 /* Data Link Layer Up */ ++#define PCIE_RC_DR_CURRENT_POWER_STATE 0x0000000E /* Current Power State */ ++#define PCIE_RC_DR_CURRENT_POWER_STATE_S 1 ++#define PCIE_RC_DR_CURRENT_LTSSM_STATE 0x000001F0 /* Current LTSSM State */ ++#define PCIE_RC_DR_CURRENT_LTSSM_STATE_S 4 ++ ++#define PCIE_RC_DR_PM_DEV_STATE 0x00000E00 /* Power Management D-State */ ++#define PCIE_RC_DR_PM_DEV_STATE_S 9 ++ ++#define PCIE_RC_DR_PM_ENABLED 0x00001000 /* Power Management State from PMU */ ++#define PCIE_RC_DR_PME_EVENT_ENABLED 0x00002000 /* Power Management Event Enable State */ ++#define PCIE_RC_DR_AUX_POWER_ENABLED 0x00004000 /* Auxiliary Power Enable */ ++ ++/* Current Power State Definition */ ++enum { ++ PCIE_RC_DR_D0 = 0, ++ PCIE_RC_DR_D1, /* Not supported */ ++ PCIE_RC_DR_D2, /* Not supported */ ++ PCIE_RC_DR_D3, ++ PCIE_RC_DR_UN, ++}; ++ ++/* PHY Link Status Register */ ++#define PCIE_PHY_SR(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x18) ++#define PCIE_PHY_SR_PHY_LINK_UP 0x00000001 /* PHY Link Up/Down Indicator */ ++ ++/* Electromechanical Control Register */ ++#define PCIE_EM_CR(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x1C) ++#define PCIE_EM_CR_CARD_IS_PRESENT 0x00000001 /* Card Presence Detect State */ ++#define PCIE_EM_CR_MRL_OPEN 0x00000002 /* MRL Sensor State */ ++#define PCIE_EM_CR_POWER_FAULT_SET 0x00000004 /* Power Fault Detected */ ++#define PCIE_EM_CR_MRL_SENSOR_SET 0x00000008 /* MRL Sensor Changed */ ++#define PCIE_EM_CR_PRESENT_DETECT_SET 0x00000010 /* Card Presense Detect Changed */ ++#define PCIE_EM_CR_CMD_CPL_INT_SET 0x00000020 /* Command Complete Interrupt */ ++#define PCIE_EM_CR_SYS_INTERLOCK_SET 0x00000040 /* System Electromechanical IterLock Engaged */ ++#define PCIE_EM_CR_ATTENTION_BUTTON_SET 0x00000080 /* Attention Button Pressed */ ++ ++/* Interrupt Status Register */ ++#define PCIE_IR_SR(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x20) ++#define PCIE_IR_SR_PME_CAUSE_MSI 0x00000002 /* MSI caused by PME */ ++#define PCIE_IR_SR_HP_PME_WAKE_GEN 0x00000004 /* Hotplug PME Wake Generation */ ++#define PCIE_IR_SR_HP_MSI 0x00000008 /* Hotplug MSI */ ++#define PCIE_IR_SR_AHB_LU_ERR 0x00000030 /* AHB Bridge Lookup Error Signals */ ++#define PCIE_IR_SR_AHB_LU_ERR_S 4 ++#define PCIE_IR_SR_INT_MSG_NUM 0x00003E00 /* Interrupt Message Number */ ++#define PCIE_IR_SR_INT_MSG_NUM_S 9 ++#define PCIE_IR_SR_AER_INT_MSG_NUM 0xF8000000 /* Advanced Error Interrupt Message Number */ ++#define PCIE_IR_SR_AER_INT_MSG_NUM_S 27 ++ ++/* Message Control Register */ ++#define PCIE_MSG_CR(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x30) ++#define PCIE_MSG_CR_GEN_PME_TURN_OFF_MSG 0x00000001 /* Generate PME Turn Off Message */ ++#define PCIE_MSG_CR_GEN_UNLOCK_MSG 0x00000002 /* Generate Unlock Message */ ++ ++#define PCIE_VDM_DR(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x34) ++ ++/* Vendor-Defined Message Requester ID Register */ ++#define PCIE_VDM_RID(X) (PCIE_APP_PORT_TO_BASE (X) + 0x38) ++#define PCIE_VDM_RID_VENROR_MSG_REQ_ID 0x0000FFFF ++#define PCIE_VDM_RID_VDMRID_S 0 ++ ++/* ASPM Control Register */ ++#define PCIE_ASPM_CR(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x40) ++#define PCIE_ASPM_CR_HOT_RST 0x00000001 /* Hot Reset Request to the downstream device */ ++#define PCIE_ASPM_CR_REQ_EXIT_L1 0x00000002 /* Request to Exit L1 */ ++#define PCIE_ASPM_CR_REQ_ENTER_L1 0x00000004 /* Request to Enter L1 */ ++ ++/* Vendor Message DW0 Register */ ++#define PCIE_VM_MSG_DW0(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x50) ++#define PCIE_VM_MSG_DW0_TYPE 0x0000001F /* Message type */ ++#define PCIE_VM_MSG_DW0_TYPE_S 0 ++#define PCIE_VM_MSG_DW0_FORMAT 0x00000060 /* Format */ ++#define PCIE_VM_MSG_DW0_FORMAT_S 5 ++#define PCIE_VM_MSG_DW0_TC 0x00007000 /* Traffic Class */ ++#define PCIE_VM_MSG_DW0_TC_S 12 ++#define PCIE_VM_MSG_DW0_ATTR 0x000C0000 /* Atrributes */ ++#define PCIE_VM_MSG_DW0_ATTR_S 18 ++#define PCIE_VM_MSG_DW0_EP_TLP 0x00100000 /* Poisoned TLP */ ++#define PCIE_VM_MSG_DW0_TD 0x00200000 /* TLP Digest */ ++#define PCIE_VM_MSG_DW0_LEN 0xFFC00000 /* Length */ ++#define PCIE_VM_MSG_DW0_LEN_S 22 ++ ++/* Format Definition */ ++enum { ++ PCIE_VM_MSG_FORMAT_00 = 0, /* 3DW Hdr, no data*/ ++ PCIE_VM_MSG_FORMAT_01, /* 4DW Hdr, no data */ ++ PCIE_VM_MSG_FORMAT_10, /* 3DW Hdr, with data */ ++ PCIE_VM_MSG_FORMAT_11, /* 4DW Hdr, with data */ ++}; ++ ++/* Traffic Class Definition */ ++enum { ++ PCIE_VM_MSG_TC0 = 0, ++ PCIE_VM_MSG_TC1, ++ PCIE_VM_MSG_TC2, ++ PCIE_VM_MSG_TC3, ++ PCIE_VM_MSG_TC4, ++ PCIE_VM_MSG_TC5, ++ PCIE_VM_MSG_TC6, ++ PCIE_VM_MSG_TC7, ++}; ++ ++/* Attributes Definition */ ++enum { ++ PCIE_VM_MSG_ATTR_00 = 0, /* RO and No Snoop cleared */ ++ PCIE_VM_MSG_ATTR_01, /* RO cleared , No Snoop set */ ++ PCIE_VM_MSG_ATTR_10, /* RO set, No Snoop cleared*/ ++ PCIE_VM_MSG_ATTR_11, /* RO and No Snoop set */ ++}; ++ ++/* Payload Size Definition */ ++#define PCIE_VM_MSG_LEN_MIN 0 ++#define PCIE_VM_MSG_LEN_MAX 1024 ++ ++/* Vendor Message DW1 Register */ ++#define PCIE_VM_MSG_DW1(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x54) ++#define PCIE_VM_MSG_DW1_FUNC_NUM 0x00000070 /* Function Number */ ++#define PCIE_VM_MSG_DW1_FUNC_NUM_S 8 ++#define PCIE_VM_MSG_DW1_CODE 0x00FF0000 /* Message Code */ ++#define PCIE_VM_MSG_DW1_CODE_S 16 ++#define PCIE_VM_MSG_DW1_TAG 0xFF000000 /* Tag */ ++#define PCIE_VM_MSG_DW1_TAG_S 24 ++ ++#define PCIE_VM_MSG_DW2(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x58) ++#define PCIE_VM_MSG_DW3(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x5C) ++ ++/* Vendor Message Request Register */ ++#define PCIE_VM_MSG_REQR(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x60) ++#define PCIE_VM_MSG_REQR_REQ 0x00000001 /* Vendor Message Request */ ++ ++ ++/* AHB Slave Side Band Control Register */ ++#define PCIE_AHB_SSB(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x70) ++#define PCIE_AHB_SSB_REQ_BCM 0x00000001 /* Slave Reques BCM filed */ ++#define PCIE_AHB_SSB_REQ_EP 0x00000002 /* Slave Reques EP filed */ ++#define PCIE_AHB_SSB_REQ_TD 0x00000004 /* Slave Reques TD filed */ ++#define PCIE_AHB_SSB_REQ_ATTR 0x00000018 /* Slave Reques Attribute number */ ++#define PCIE_AHB_SSB_REQ_ATTR_S 3 ++#define PCIE_AHB_SSB_REQ_TC 0x000000E0 /* Slave Request TC Field */ ++#define PCIE_AHB_SSB_REQ_TC_S 5 ++ ++/* AHB Master SideBand Ctrl Register */ ++#define PCIE_AHB_MSB(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x74) ++#define PCIE_AHB_MSB_RESP_ATTR 0x00000003 /* Master Response Attribute number */ ++#define PCIE_AHB_MSB_RESP_ATTR_S 0 ++#define PCIE_AHB_MSB_RESP_BAD_EOT 0x00000004 /* Master Response Badeot filed */ ++#define PCIE_AHB_MSB_RESP_BCM 0x00000008 /* Master Response BCM filed */ ++#define PCIE_AHB_MSB_RESP_EP 0x00000010 /* Master Response EP filed */ ++#define PCIE_AHB_MSB_RESP_TD 0x00000020 /* Master Response TD filed */ ++#define PCIE_AHB_MSB_RESP_FUN_NUM 0x000003C0 /* Master Response Function number */ ++#define PCIE_AHB_MSB_RESP_FUN_NUM_S 6 ++ ++/* AHB Control Register, fixed bus enumeration exception */ ++#define PCIE_AHB_CTRL(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x78) ++#define PCIE_AHB_CTRL_BUS_ERROR_SUPPRESS 0x00000001 ++ ++/* Interrupt Enalbe Register */ ++#define PCIE_IRNEN(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0xF4) ++#define PCIE_IRNCR(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0xF8) ++#define PCIE_IRNICR(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0xFC) ++ ++/* PCIe interrupt enable/control/capture register definition */ ++#define PCIE_IRN_AER_REPORT 0x00000001 /* AER Interrupt */ ++#define PCIE_IRN_AER_MSIX 0x00000002 /* Advanced Error MSI-X Interrupt */ ++#define PCIE_IRN_PME 0x00000004 /* PME Interrupt */ ++#define PCIE_IRN_HOTPLUG 0x00000008 /* Hotplug Interrupt */ ++#define PCIE_IRN_RX_VDM_MSG 0x00000010 /* Vendor-Defined Message Interrupt */ ++#define PCIE_IRN_RX_CORRECTABLE_ERR_MSG 0x00000020 /* Correctable Error Message Interrupt */ ++#define PCIE_IRN_RX_NON_FATAL_ERR_MSG 0x00000040 /* Non-fatal Error Message */ ++#define PCIE_IRN_RX_FATAL_ERR_MSG 0x00000080 /* Fatal Error Message */ ++#define PCIE_IRN_RX_PME_MSG 0x00000100 /* PME Message Interrupt */ ++#define PCIE_IRN_RX_PME_TURNOFF_ACK 0x00000200 /* PME Turnoff Ack Message Interrupt */ ++#define PCIE_IRN_AHB_BR_FATAL_ERR 0x00000400 /* AHB Fatal Error Interrupt */ ++#define PCIE_IRN_LINK_AUTO_BW_STATUS 0x00000800 /* Link Auto Bandwidth Status Interrupt */ ++#define PCIE_IRN_BW_MGT 0x00001000 /* Bandwidth Managment Interrupt */ ++#define PCIE_IRN_INTA 0x00002000 /* INTA */ ++#define PCIE_IRN_INTB 0x00004000 /* INTB */ ++#define PCIE_IRN_INTC 0x00008000 /* INTC */ ++#define PCIE_IRN_INTD 0x00010000 /* INTD */ ++#define PCIE_IRN_WAKEUP 0x00020000 /* Wake up Interrupt */ ++ ++#define PCIE_RC_CORE_COMBINED_INT (PCIE_IRN_AER_REPORT | PCIE_IRN_AER_MSIX | PCIE_IRN_PME | \ ++ PCIE_IRN_HOTPLUG | PCIE_IRN_RX_VDM_MSG | PCIE_IRN_RX_CORRECTABLE_ERR_MSG |\ ++ PCIE_IRN_RX_NON_FATAL_ERR_MSG | PCIE_IRN_RX_FATAL_ERR_MSG | \ ++ PCIE_IRN_RX_PME_MSG | PCIE_IRN_RX_PME_TURNOFF_ACK | PCIE_IRN_AHB_BR_FATAL_ERR | \ ++ PCIE_IRN_LINK_AUTO_BW_STATUS | PCIE_IRN_BW_MGT) ++/* PCIe RC Configuration Register */ ++#define PCIE_VDID(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x00) ++ ++/* Bit definition from pci_reg.h */ ++#define PCIE_PCICMDSTS(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x04) ++#define PCIE_CCRID(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x08) ++#define PCIE_CLSLTHTBR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x0C) /* EP only */ ++/* BAR0, BAR1,Only necessary if the bridges implements a device-specific register set or memory buffer */ ++#define PCIE_BAR0(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x10) /* Not used*/ ++#define PCIE_BAR1(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x14) /* Not used */ ++ ++#define PCIE_BNR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x18) /* Mandatory */ ++/* Bus Number Register bits */ ++#define PCIE_BNR_PRIMARY_BUS_NUM 0x000000FF ++#define PCIE_BNR_PRIMARY_BUS_NUM_S 0 ++#define PCIE_PNR_SECONDARY_BUS_NUM 0x0000FF00 ++#define PCIE_PNR_SECONDARY_BUS_NUM_S 8 ++#define PCIE_PNR_SUB_BUS_NUM 0x00FF0000 ++#define PCIE_PNR_SUB_BUS_NUM_S 16 ++ ++/* IO Base/Limit Register bits */ ++#define PCIE_IOBLSECS(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x1C) /* RC only */ ++#define PCIE_IOBLSECS_32BIT_IO_ADDR 0x00000001 ++#define PCIE_IOBLSECS_IO_BASE_ADDR 0x000000F0 ++#define PCIE_IOBLSECS_IO_BASE_ADDR_S 4 ++#define PCIE_IOBLSECS_32BIT_IOLIMT 0x00000100 ++#define PCIE_IOBLSECS_IO_LIMIT_ADDR 0x0000F000 ++#define PCIE_IOBLSECS_IO_LIMIT_ADDR_S 12 ++ ++/* Non-prefetchable Memory Base/Limit Register bit */ ++#define PCIE_MBML(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x20) /* RC only */ ++#define PCIE_MBML_MEM_BASE_ADDR 0x0000FFF0 ++#define PCIE_MBML_MEM_BASE_ADDR_S 4 ++#define PCIE_MBML_MEM_LIMIT_ADDR 0xFFF00000 ++#define PCIE_MBML_MEM_LIMIT_ADDR_S 20 ++ ++/* Prefetchable Memory Base/Limit Register bit */ ++#define PCIE_PMBL(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x24) /* RC only */ ++#define PCIE_PMBL_64BIT_ADDR 0x00000001 ++#define PCIE_PMBL_UPPER_12BIT 0x0000FFF0 ++#define PCIE_PMBL_UPPER_12BIT_S 4 ++#define PCIE_PMBL_E64MA 0x00010000 ++#define PCIE_PMBL_END_ADDR 0xFFF00000 ++#define PCIE_PMBL_END_ADDR_S 20 ++#define PCIE_PMBU32(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x28) /* RC only */ ++#define PCIE_PMLU32(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x2C) /* RC only */ ++ ++/* I/O Base/Limit Upper 16 bits register */ ++#define PCIE_IO_BANDL(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x30) /* RC only */ ++#define PCIE_IO_BANDL_UPPER_16BIT_IO_BASE 0x0000FFFF ++#define PCIE_IO_BANDL_UPPER_16BIT_IO_BASE_S 0 ++#define PCIE_IO_BANDL_UPPER_16BIT_IO_LIMIT 0xFFFF0000 ++#define PCIE_IO_BANDL_UPPER_16BIT_IO_LIMIT_S 16 ++ ++#define PCIE_CPR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x34) ++#define PCIE_EBBAR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x38) ++ ++/* Interrupt and Secondary Bridge Control Register */ ++#define PCIE_INTRBCTRL(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x3C) ++ ++#define PCIE_INTRBCTRL_INT_LINE 0x000000FF ++#define PCIE_INTRBCTRL_INT_LINE_S 0 ++#define PCIE_INTRBCTRL_INT_PIN 0x0000FF00 ++#define PCIE_INTRBCTRL_INT_PIN_S 8 ++#define PCIE_INTRBCTRL_PARITY_ERR_RESP_ENABLE 0x00010000 /* #PERR */ ++#define PCIE_INTRBCTRL_SERR_ENABLE 0x00020000 /* #SERR */ ++#define PCIE_INTRBCTRL_ISA_ENABLE 0x00040000 /* ISA enable, IO 64KB only */ ++#define PCIE_INTRBCTRL_VGA_ENABLE 0x00080000 /* VGA enable */ ++#define PCIE_INTRBCTRL_VGA_16BIT_DECODE 0x00100000 /* VGA 16bit decode */ ++#define PCIE_INTRBCTRL_RST_SECONDARY_BUS 0x00400000 /* Secondary bus rest, hot rest, 1ms */ ++/* Others are read only */ ++enum { ++ PCIE_INTRBCTRL_INT_NON = 0, ++ PCIE_INTRBCTRL_INTA, ++ PCIE_INTRBCTRL_INTB, ++ PCIE_INTRBCTRL_INTC, ++ PCIE_INTRBCTRL_INTD, ++}; ++ ++#define PCIE_PM_CAPR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x40) ++ ++/* Power Management Control and Status Register */ ++#define PCIE_PM_CSR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x44) ++ ++#define PCIE_PM_CSR_POWER_STATE 0x00000003 /* Power State */ ++#define PCIE_PM_CSR_POWER_STATE_S 0 ++#define PCIE_PM_CSR_SW_RST 0x00000008 /* Soft Reset Enabled */ ++#define PCIE_PM_CSR_PME_ENABLE 0x00000100 /* PME Enable */ ++#define PCIE_PM_CSR_PME_STATUS 0x00008000 /* PME status */ ++ ++/* MSI Capability Register for EP */ ++#define PCIE_MCAPR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x50) ++ ++#define PCIE_MCAPR_MSI_CAP_ID 0x000000FF /* MSI Capability ID */ ++#define PCIE_MCAPR_MSI_CAP_ID_S 0 ++#define PCIE_MCAPR_MSI_NEXT_CAP_PTR 0x0000FF00 /* Next Capability Pointer */ ++#define PCIE_MCAPR_MSI_NEXT_CAP_PTR_S 8 ++#define PCIE_MCAPR_MSI_ENABLE 0x00010000 /* MSI Enable */ ++#define PCIE_MCAPR_MULTI_MSG_CAP 0x000E0000 /* Multiple Message Capable */ ++#define PCIE_MCAPR_MULTI_MSG_CAP_S 17 ++#define PCIE_MCAPR_MULTI_MSG_ENABLE 0x00700000 /* Multiple Message Enable */ ++#define PCIE_MCAPR_MULTI_MSG_ENABLE_S 20 ++#define PCIE_MCAPR_ADDR64_CAP 0X00800000 /* 64-bit Address Capable */ ++ ++/* MSI Message Address Register */ ++#define PCIE_MA(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x54) ++ ++#define PCIE_MA_ADDR_MASK 0xFFFFFFFC /* Message Address */ ++ ++/* MSI Message Upper Address Register */ ++#define PCIE_MUA(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x58) ++ ++/* MSI Message Data Register */ ++#define PCIE_MD(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x5C) ++ ++#define PCIE_MD_DATA 0x0000FFFF /* Message Data */ ++#define PCIE_MD_DATA_S 0 ++ ++/* PCI Express Capability Register */ ++#define PCIE_XCAP(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x70) ++ ++#define PCIE_XCAP_ID 0x000000FF /* PCI Express Capability ID */ ++#define PCIE_XCAP_ID_S 0 ++#define PCIE_XCAP_NEXT_CAP 0x0000FF00 /* Next Capability Pointer */ ++#define PCIE_XCAP_NEXT_CAP_S 8 ++#define PCIE_XCAP_VER 0x000F0000 /* PCI Express Capability Version */ ++#define PCIE_XCAP_VER_S 16 ++#define PCIE_XCAP_DEV_PORT_TYPE 0x00F00000 /* Device Port Type */ ++#define PCIE_XCAP_DEV_PORT_TYPE_S 20 ++#define PCIE_XCAP_SLOT_IMPLEMENTED 0x01000000 /* Slot Implemented */ ++#define PCIE_XCAP_MSG_INT_NUM 0x3E000000 /* Interrupt Message Number */ ++#define PCIE_XCAP_MSG_INT_NUM_S 25 ++ ++/* Device Capability Register */ ++#define PCIE_DCAP(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x74) ++ ++#define PCIE_DCAP_MAX_PAYLOAD_SIZE 0x00000007 /* Max Payload size */ ++#define PCIE_DCAP_MAX_PAYLOAD_SIZE_S 0 ++#define PCIE_DCAP_PHANTOM_FUNC 0x00000018 /* Phanton Function, not supported */ ++#define PCIE_DCAP_PHANTOM_FUNC_S 3 ++#define PCIE_DCAP_EXT_TAG 0x00000020 /* Extended Tag Field */ ++#define PCIE_DCAP_EP_L0S_LATENCY 0x000001C0 /* EP L0s latency only */ ++#define PCIE_DCAP_EP_L0S_LATENCY_S 6 ++#define PCIE_DCAP_EP_L1_LATENCY 0x00000E00 /* EP L1 latency only */ ++#define PCIE_DCAP_EP_L1_LATENCY_S 9 ++#define PCIE_DCAP_ROLE_BASE_ERR_REPORT 0x00008000 /* Role Based ERR */ ++ ++/* Maximum payload size supported */ ++enum { ++ PCIE_MAX_PAYLOAD_128 = 0, ++ PCIE_MAX_PAYLOAD_256, ++ PCIE_MAX_PAYLOAD_512, ++ PCIE_MAX_PAYLOAD_1024, ++ PCIE_MAX_PAYLOAD_2048, ++ PCIE_MAX_PAYLOAD_4096, ++}; ++ ++/* Device Control and Status Register */ ++#define PCIE_DCTLSTS(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x78) ++ ++#define PCIE_DCTLSTS_CORRECTABLE_ERR_EN 0x00000001 /* COR-ERR */ ++#define PCIE_DCTLSTS_NONFATAL_ERR_EN 0x00000002 /* Non-fatal ERR */ ++#define PCIE_DCTLSTS_FATAL_ERR_EN 0x00000004 /* Fatal ERR */ ++#define PCIE_DCTLSYS_UR_REQ_EN 0x00000008 /* UR ERR */ ++#define PCIE_DCTLSTS_RELAXED_ORDERING_EN 0x00000010 /* Enable relaxing ordering */ ++#define PCIE_DCTLSTS_MAX_PAYLOAD_SIZE 0x000000E0 /* Max payload mask */ ++#define PCIE_DCTLSTS_MAX_PAYLOAD_SIZE_S 5 ++#define PCIE_DCTLSTS_EXT_TAG_EN 0x00000100 /* Extended tag field */ ++#define PCIE_DCTLSTS_PHANTOM_FUNC_EN 0x00000200 /* Phantom Function Enable */ ++#define PCIE_DCTLSTS_AUX_PM_EN 0x00000400 /* AUX Power PM Enable */ ++#define PCIE_DCTLSTS_NO_SNOOP_EN 0x00000800 /* Enable no snoop, except root port*/ ++#define PCIE_DCTLSTS_MAX_READ_SIZE 0x00007000 /* Max Read Request size*/ ++#define PCIE_DCTLSTS_MAX_READ_SIZE_S 12 ++#define PCIE_DCTLSTS_CORRECTABLE_ERR 0x00010000 /* COR-ERR Detected */ ++#define PCIE_DCTLSTS_NONFATAL_ERR 0x00020000 /* Non-Fatal ERR Detected */ ++#define PCIE_DCTLSTS_FATAL_ER 0x00040000 /* Fatal ERR Detected */ ++#define PCIE_DCTLSTS_UNSUPPORTED_REQ 0x00080000 /* UR Detected */ ++#define PCIE_DCTLSTS_AUX_POWER 0x00100000 /* Aux Power Detected */ ++#define PCIE_DCTLSTS_TRANSACT_PENDING 0x00200000 /* Transaction pending */ ++ ++#define PCIE_DCTLSTS_ERR_EN (PCIE_DCTLSTS_CORRECTABLE_ERR_EN | \ ++ PCIE_DCTLSTS_NONFATAL_ERR_EN | PCIE_DCTLSTS_FATAL_ERR_EN | \ ++ PCIE_DCTLSYS_UR_REQ_EN) ++ ++/* Link Capability Register */ ++#define PCIE_LCAP(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x7C) ++#define PCIE_LCAP_MAX_LINK_SPEED 0x0000000F /* Max link speed, 0x1 by default */ ++#define PCIE_LCAP_MAX_LINK_SPEED_S 0 ++#define PCIE_LCAP_MAX_LENGTH_WIDTH 0x000003F0 /* Maxium Length Width */ ++#define PCIE_LCAP_MAX_LENGTH_WIDTH_S 4 ++#define PCIE_LCAP_ASPM_LEVEL 0x00000C00 /* Active State Link PM Support */ ++#define PCIE_LCAP_ASPM_LEVEL_S 10 ++#define PCIE_LCAP_L0S_EIXT_LATENCY 0x00007000 /* L0s Exit Latency */ ++#define PCIE_LCAP_L0S_EIXT_LATENCY_S 12 ++#define PCIE_LCAP_L1_EXIT_LATENCY 0x00038000 /* L1 Exit Latency */ ++#define PCIE_LCAP_L1_EXIT_LATENCY_S 15 ++#define PCIE_LCAP_CLK_PM 0x00040000 /* Clock Power Management */ ++#define PCIE_LCAP_SDER 0x00080000 /* Surprise Down Error Reporting */ ++#define PCIE_LCAP_DLL_ACTIVE_REPROT 0x00100000 /* Data Link Layer Active Reporting Capable */ ++#define PCIE_LCAP_PORT_NUM 0xFF0000000 /* Port number */ ++#define PCIE_LCAP_PORT_NUM_S 24 ++ ++/* Maximum Length width definition */ ++#define PCIE_MAX_LENGTH_WIDTH_RES 0x00 ++#define PCIE_MAX_LENGTH_WIDTH_X1 0x01 /* Default */ ++#define PCIE_MAX_LENGTH_WIDTH_X2 0x02 ++#define PCIE_MAX_LENGTH_WIDTH_X4 0x04 ++#define PCIE_MAX_LENGTH_WIDTH_X8 0x08 ++#define PCIE_MAX_LENGTH_WIDTH_X12 0x0C ++#define PCIE_MAX_LENGTH_WIDTH_X16 0x10 ++#define PCIE_MAX_LENGTH_WIDTH_X32 0x20 ++ ++/* Active State Link PM definition */ ++enum { ++ PCIE_ASPM_RES0 = 0, ++ PCIE_ASPM_L0S_ENTRY_SUPPORT, /* L0s */ ++ PCIE_ASPM_RES1, ++ PCIE_ASPM_L0S_L1_ENTRY_SUPPORT, /* L0s and L1, default */ ++}; ++ ++/* L0s Exit Latency definition */ ++enum { ++ PCIE_L0S_EIXT_LATENCY_L64NS = 0, /* < 64 ns */ ++ PCIE_L0S_EIXT_LATENCY_B64A128, /* > 64 ns < 128 ns */ ++ PCIE_L0S_EIXT_LATENCY_B128A256, /* > 128 ns < 256 ns */ ++ PCIE_L0S_EIXT_LATENCY_B256A512, /* > 256 ns < 512 ns */ ++ PCIE_L0S_EIXT_LATENCY_B512TO1U, /* > 512 ns < 1 us */ ++ PCIE_L0S_EIXT_LATENCY_B1A2U, /* > 1 us < 2 us */ ++ PCIE_L0S_EIXT_LATENCY_B2A4U, /* > 2 us < 4 us */ ++ PCIE_L0S_EIXT_LATENCY_M4US, /* > 4 us */ ++}; ++ ++/* L1 Exit Latency definition */ ++enum { ++ PCIE_L1_EXIT_LATENCY_L1US = 0, /* < 1 us */ ++ PCIE_L1_EXIT_LATENCY_B1A2, /* > 1 us < 2 us */ ++ PCIE_L1_EXIT_LATENCY_B2A4, /* > 2 us < 4 us */ ++ PCIE_L1_EXIT_LATENCY_B4A8, /* > 4 us < 8 us */ ++ PCIE_L1_EXIT_LATENCY_B8A16, /* > 8 us < 16 us */ ++ PCIE_L1_EXIT_LATENCY_B16A32, /* > 16 us < 32 us */ ++ PCIE_L1_EXIT_LATENCY_B32A64, /* > 32 us < 64 us */ ++ PCIE_L1_EXIT_LATENCY_M64US, /* > 64 us */ ++}; ++ ++/* Link Control and Status Register */ ++#define PCIE_LCTLSTS(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x80) ++#define PCIE_LCTLSTS_ASPM_ENABLE 0x00000003 /* Active State Link PM Control */ ++#define PCIE_LCTLSTS_ASPM_ENABLE_S 0 ++#define PCIE_LCTLSTS_RCB128 0x00000008 /* Read Completion Boundary 128*/ ++#define PCIE_LCTLSTS_LINK_DISABLE 0x00000010 /* Link Disable */ ++#define PCIE_LCTLSTS_RETRIAN_LINK 0x00000020 /* Retrain Link */ ++#define PCIE_LCTLSTS_COM_CLK_CFG 0x00000040 /* Common Clock Configuration */ ++#define PCIE_LCTLSTS_EXT_SYNC 0x00000080 /* Extended Synch */ ++#define PCIE_LCTLSTS_CLK_PM_EN 0x00000100 /* Enable Clock Powerm Management */ ++#define PCIE_LCTLSTS_LINK_SPEED 0x000F0000 /* Link Speed */ ++#define PCIE_LCTLSTS_LINK_SPEED_S 16 ++#define PCIE_LCTLSTS_NEGOTIATED_LINK_WIDTH 0x03F00000 /* Negotiated Link Width */ ++#define PCIE_LCTLSTS_NEGOTIATED_LINK_WIDTH_S 20 ++#define PCIE_LCTLSTS_RETRAIN_PENDING 0x08000000 /* Link training is ongoing */ ++#define PCIE_LCTLSTS_SLOT_CLK_CFG 0x10000000 /* Slot Clock Configuration */ ++#define PCIE_LCTLSTS_DLL_ACTIVE 0x20000000 /* Data Link Layer Active */ ++ ++/* Slot Capabilities Register */ ++#define PCIE_SLCAP(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x84) ++ ++/* Slot Capabilities */ ++#define PCIE_SLCTLSTS(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x88) ++ ++/* Root Control and Capability Register */ ++#define PCIE_RCTLCAP(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x8C) ++#define PCIE_RCTLCAP_SERR_ON_CORRECTABLE_ERR 0x00000001 /* #SERR on COR-ERR */ ++#define PCIE_RCTLCAP_SERR_ON_NONFATAL_ERR 0x00000002 /* #SERR on Non-Fatal ERR */ ++#define PCIE_RCTLCAP_SERR_ON_FATAL_ERR 0x00000004 /* #SERR on Fatal ERR */ ++#define PCIE_RCTLCAP_PME_INT_EN 0x00000008 /* PME Interrupt Enable */ ++#define PCIE_RCTLCAP_SERR_ENABLE (PCIE_RCTLCAP_SERR_ON_CORRECTABLE_ERR | \ ++ PCIE_RCTLCAP_SERR_ON_NONFATAL_ERR | PCIE_RCTLCAP_SERR_ON_FATAL_ERR) ++/* Root Status Register */ ++#define PCIE_RSTS(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x90) ++#define PCIE_RSTS_PME_REQ_ID 0x0000FFFF /* PME Request ID */ ++#define PCIE_RSTS_PME_REQ_ID_S 0 ++#define PCIE_RSTS_PME_STATUS 0x00010000 /* PME Status */ ++#define PCIE_RSTS_PME_PENDING 0x00020000 /* PME Pending */ ++ ++/* PCI Express Enhanced Capability Header */ ++#define PCIE_ENHANCED_CAP(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x100) ++#define PCIE_ENHANCED_CAP_ID 0x0000FFFF /* PCI Express Extended Capability ID */ ++#define PCIE_ENHANCED_CAP_ID_S 0 ++#define PCIE_ENHANCED_CAP_VER 0x000F0000 /* Capability Version */ ++#define PCIE_ENHANCED_CAP_VER_S 16 ++#define PCIE_ENHANCED_CAP_NEXT_OFFSET 0xFFF00000 /* Next Capability Offset */ ++#define PCIE_ENHANCED_CAP_NEXT_OFFSET_S 20 ++ ++/* Uncorrectable Error Status Register */ ++#define PCIE_UES_R(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x104) ++#define PCIE_DATA_LINK_PROTOCOL_ERR 0x00000010 /* Data Link Protocol Error Status */ ++#define PCIE_SURPRISE_DOWN_ERROR 0x00000020 /* Surprise Down Error Status */ ++#define PCIE_POISONED_TLP 0x00001000 /* Poisoned TLP Status */ ++#define PCIE_FC_PROTOCOL_ERR 0x00002000 /* Flow Control Protocol Error Status */ ++#define PCIE_COMPLETION_TIMEOUT 0x00004000 /* Completion Timeout Status */ ++#define PCIE_COMPLETOR_ABORT 0x00008000 /* Completer Abort Error */ ++#define PCIE_UNEXPECTED_COMPLETION 0x00010000 /* Unexpected Completion Status */ ++#define PCIE_RECEIVER_OVERFLOW 0x00020000 /* Receive Overflow Status */ ++#define PCIE_MALFORNED_TLP 0x00040000 /* Malformed TLP Stauts */ ++#define PCIE_ECRC_ERR 0x00080000 /* ECRC Error Stauts */ ++#define PCIE_UR_REQ 0x00100000 /* Unsupported Request Error Status */ ++#define PCIE_ALL_UNCORRECTABLE_ERR (PCIE_DATA_LINK_PROTOCOL_ERR | PCIE_SURPRISE_DOWN_ERROR | \ ++ PCIE_POISONED_TLP | PCIE_FC_PROTOCOL_ERR | PCIE_COMPLETION_TIMEOUT | \ ++ PCIE_COMPLETOR_ABORT | PCIE_UNEXPECTED_COMPLETION | PCIE_RECEIVER_OVERFLOW |\ ++ PCIE_MALFORNED_TLP | PCIE_ECRC_ERR | PCIE_UR_REQ) ++ ++/* Uncorrectable Error Mask Register, Mask means no report */ ++#define PCIE_UEMR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x108) ++ ++/* Uncorrectable Error Severity Register */ ++#define PCIE_UESR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x10C) ++ ++/* Correctable Error Status Register */ ++#define PCIE_CESR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x110) ++#define PCIE_RX_ERR 0x00000001 /* Receive Error Status */ ++#define PCIE_BAD_TLP 0x00000040 /* Bad TLP Status */ ++#define PCIE_BAD_DLLP 0x00000080 /* Bad DLLP Status */ ++#define PCIE_REPLAY_NUM_ROLLOVER 0x00000100 /* Replay Number Rollover Status */ ++#define PCIE_REPLAY_TIMER_TIMEOUT_ERR 0x00001000 /* Reply Timer Timeout Status */ ++#define PCIE_ADVISORY_NONFTAL_ERR 0x00002000 /* Advisory Non-Fatal Error Status */ ++#define PCIE_CORRECTABLE_ERR (PCIE_RX_ERR | PCIE_BAD_TLP | PCIE_BAD_DLLP | PCIE_REPLAY_NUM_ROLLOVER |\ ++ PCIE_REPLAY_TIMER_TIMEOUT_ERR | PCIE_ADVISORY_NONFTAL_ERR) ++ ++/* Correctable Error Mask Register */ ++#define PCIE_CEMR(X) (volatile u32*)(PCIE_RC_CFG_BASE + 0x114) ++ ++/* Advanced Error Capabilities and Control Register */ ++#define PCIE_AECCR(X) (volatile u32*)(PCIE_RC_CFG_BASE + 0x118) ++#define PCIE_AECCR_FIRST_ERR_PTR 0x0000001F /* First Error Pointer */ ++#define PCIE_AECCR_FIRST_ERR_PTR_S 0 ++#define PCIE_AECCR_ECRC_GEN_CAP 0x00000020 /* ECRC Generation Capable */ ++#define PCIE_AECCR_ECRC_GEN_EN 0x00000040 /* ECRC Generation Enable */ ++#define PCIE_AECCR_ECRC_CHECK_CAP 0x00000080 /* ECRC Check Capable */ ++#define PCIE_AECCR_ECRC_CHECK_EN 0x00000100 /* ECRC Check Enable */ ++ ++/* Header Log Register 1 */ ++#define PCIE_HLR1(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x11C) ++ ++/* Header Log Register 2 */ ++#define PCIE_HLR2(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x120) ++ ++/* Header Log Register 3 */ ++#define PCIE_HLR3(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x124) ++ ++/* Header Log Register 4 */ ++#define PCIE_HLR4(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x128) ++ ++/* Root Error Command Register */ ++#define PCIE_RECR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x12C) ++#define PCIE_RECR_CORRECTABLE_ERR_REPORT_EN 0x00000001 /* COR-ERR */ ++#define PCIE_RECR_NONFATAL_ERR_REPORT_EN 0x00000002 /* Non-Fatal ERR */ ++#define PCIE_RECR_FATAL_ERR_REPORT_EN 0x00000004 /* Fatal ERR */ ++#define PCIE_RECR_ERR_REPORT_EN (PCIE_RECR_CORRECTABLE_ERR_REPORT_EN | \ ++ PCIE_RECR_NONFATAL_ERR_REPORT_EN | PCIE_RECR_FATAL_ERR_REPORT_EN) ++ ++/* Root Error Status Register */ ++#define PCIE_RESR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x130) ++#define PCIE_RESR_CORRECTABLE_ERR 0x00000001 /* COR-ERR Receveid */ ++#define PCIE_RESR_MULTI_CORRECTABLE_ERR 0x00000002 /* Multiple COR-ERR Received */ ++#define PCIE_RESR_FATAL_NOFATAL_ERR 0x00000004 /* ERR Fatal/Non-Fatal Received */ ++#define PCIE_RESR_MULTI_FATAL_NOFATAL_ERR 0x00000008 /* Multiple ERR Fatal/Non-Fatal Received */ ++#define PCIE_RESR_FIRST_UNCORRECTABLE_FATAL_ERR 0x00000010 /* First UN-COR Fatal */ ++#define PCIR_RESR_NON_FATAL_ERR 0x00000020 /* Non-Fatal Error Message Received */ ++#define PCIE_RESR_FATAL_ERR 0x00000040 /* Fatal Message Received */ ++#define PCIE_RESR_AER_INT_MSG_NUM 0xF8000000 /* Advanced Error Interrupt Message Number */ ++#define PCIE_RESR_AER_INT_MSG_NUM_S 27 ++ ++/* Error Source Indentification Register */ ++#define PCIE_ESIR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x134) ++#define PCIE_ESIR_CORRECTABLE_ERR_SRC_ID 0x0000FFFF ++#define PCIE_ESIR_CORRECTABLE_ERR_SRC_ID_S 0 ++#define PCIE_ESIR_FATAL_NON_FATAL_SRC_ID 0xFFFF0000 ++#define PCIE_ESIR_FATAL_NON_FATAL_SRC_ID_S 16 ++ ++/* VC Enhanced Capability Header */ ++#define PCIE_VC_ECH(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x140) ++ ++/* Port VC Capability Register */ ++#define PCIE_PVC1(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x144) ++#define PCIE_PVC1_EXT_VC_CNT 0x00000007 /* Extended VC Count */ ++#define PCIE_PVC1_EXT_VC_CNT_S 0 ++#define PCIE_PVC1_LOW_PRI_EXT_VC_CNT 0x00000070 /* Low Priority Extended VC Count */ ++#define PCIE_PVC1_LOW_PRI_EXT_VC_CNT_S 4 ++#define PCIE_PVC1_REF_CLK 0x00000300 /* Reference Clock */ ++#define PCIE_PVC1_REF_CLK_S 8 ++#define PCIE_PVC1_PORT_ARB_TAB_ENTRY_SIZE 0x00000C00 /* Port Arbitration Table Entry Size */ ++#define PCIE_PVC1_PORT_ARB_TAB_ENTRY_SIZE_S 10 ++ ++/* Extended Virtual Channel Count Defintion */ ++#define PCIE_EXT_VC_CNT_MIN 0 ++#define PCIE_EXT_VC_CNT_MAX 7 ++ ++/* Port Arbitration Table Entry Size Definition */ ++enum { ++ PCIE_PORT_ARB_TAB_ENTRY_SIZE_S1BIT = 0, ++ PCIE_PORT_ARB_TAB_ENTRY_SIZE_S2BIT, ++ PCIE_PORT_ARB_TAB_ENTRY_SIZE_S4BIT, ++ PCIE_PORT_ARB_TAB_ENTRY_SIZE_S8BIT, ++}; ++ ++/* Port VC Capability Register 2 */ ++#define PCIE_PVC2(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x148) ++#define PCIE_PVC2_VC_ARB_16P_FIXED_WRR 0x00000001 /* HW Fixed arbitration, 16 phase WRR */ ++#define PCIE_PVC2_VC_ARB_32P_WRR 0x00000002 /* 32 phase WRR */ ++#define PCIE_PVC2_VC_ARB_64P_WRR 0x00000004 /* 64 phase WRR */ ++#define PCIE_PVC2_VC_ARB_128P_WRR 0x00000008 /* 128 phase WRR */ ++#define PCIE_PVC2_VC_ARB_WRR 0x0000000F ++#define PCIE_PVC2_VC_ARB_TAB_OFFSET 0xFF000000 /* VC arbitration table offset, not support */ ++#define PCIE_PVC2_VC_ARB_TAB_OFFSET_S 24 ++ ++/* Port VC Control and Status Register */ ++#define PCIE_PVCCRSR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x14C) ++#define PCIE_PVCCRSR_LOAD_VC_ARB_TAB 0x00000001 /* Load VC Arbitration Table */ ++#define PCIE_PVCCRSR_VC_ARB_SEL 0x0000000E /* VC Arbitration Select */ ++#define PCIE_PVCCRSR_VC_ARB_SEL_S 1 ++#define PCIE_PVCCRSR_VC_ARB_TAB_STATUS 0x00010000 /* Arbitration Status */ ++ ++/* VC0 Resource Capability Register */ ++#define PCIE_VC0_RC(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x150) ++#define PCIE_VC0_RC_PORT_ARB_HW_FIXED 0x00000001 /* HW Fixed arbitration */ ++#define PCIE_VC0_RC_PORT_ARB_32P_WRR 0x00000002 /* 32 phase WRR */ ++#define PCIE_VC0_RC_PORT_ARB_64P_WRR 0x00000004 /* 64 phase WRR */ ++#define PCIE_VC0_RC_PORT_ARB_128P_WRR 0x00000008 /* 128 phase WRR */ ++#define PCIE_VC0_RC_PORT_ARB_TM_128P_WRR 0x00000010 /* Time-based 128 phase WRR */ ++#define PCIE_VC0_RC_PORT_ARB_TM_256P_WRR 0x00000020 /* Time-based 256 phase WRR */ ++#define PCIE_VC0_RC_PORT_ARB (PCIE_VC0_RC_PORT_ARB_HW_FIXED | PCIE_VC0_RC_PORT_ARB_32P_WRR |\ ++ PCIE_VC0_RC_PORT_ARB_64P_WRR | PCIE_VC0_RC_PORT_ARB_128P_WRR | \ ++ PCIE_VC0_RC_PORT_ARB_TM_128P_WRR | PCIE_VC0_RC_PORT_ARB_TM_256P_WRR) ++ ++#define PCIE_VC0_RC_REJECT_SNOOP 0x00008000 /* Reject Snoop Transactioin */ ++#define PCIE_VC0_RC_MAX_TIMESLOTS 0x007F0000 /* Maximum time Slots */ ++#define PCIE_VC0_RC_MAX_TIMESLOTS_S 16 ++#define PCIE_VC0_RC_PORT_ARB_TAB_OFFSET 0xFF000000 /* Port Arbitration Table Offset */ ++#define PCIE_VC0_RC_PORT_ARB_TAB_OFFSET_S 24 ++ ++/* VC0 Resource Control Register */ ++#define PCIE_VC0_RC0(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x154) ++#define PCIE_VC0_RC0_TVM0 0x00000001 /* TC0 and VC0 */ ++#define PCIE_VC0_RC0_TVM1 0x00000002 /* TC1 and VC1 */ ++#define PCIE_VC0_RC0_TVM2 0x00000004 /* TC2 and VC2 */ ++#define PCIE_VC0_RC0_TVM3 0x00000008 /* TC3 and VC3 */ ++#define PCIE_VC0_RC0_TVM4 0x00000010 /* TC4 and VC4 */ ++#define PCIE_VC0_RC0_TVM5 0x00000020 /* TC5 and VC5 */ ++#define PCIE_VC0_RC0_TVM6 0x00000040 /* TC6 and VC6 */ ++#define PCIE_VC0_RC0_TVM7 0x00000080 /* TC7 and VC7 */ ++#define PCIE_VC0_RC0_TC_VC 0x000000FF /* TC/VC mask */ ++ ++#define PCIE_VC0_RC0_LOAD_PORT_ARB_TAB 0x00010000 /* Load Port Arbitration Table */ ++#define PCIE_VC0_RC0_PORT_ARB_SEL 0x000E0000 /* Port Arbitration Select */ ++#define PCIE_VC0_RC0_PORT_ARB_SEL_S 17 ++#define PCIE_VC0_RC0_VC_ID 0x07000000 /* VC ID */ ++#define PCIE_VC0_RC0_VC_ID_S 24 ++#define PCIE_VC0_RC0_VC_EN 0x80000000 /* VC Enable */ ++ ++/* VC0 Resource Status Register */ ++#define PCIE_VC0_RSR0(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x158) ++#define PCIE_VC0_RSR0_PORT_ARB_TAB_STATUS 0x00010000 /* Port Arbitration Table Status,not used */ ++#define PCIE_VC0_RSR0_VC_NEG_PENDING 0x00020000 /* VC Negotiation Pending */ ++ ++/* Ack Latency Timer and Replay Timer Register */ ++#define PCIE_ALTRT(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x700) ++#define PCIE_ALTRT_ROUND_TRIP_LATENCY_LIMIT 0x0000FFFF /* Round Trip Latency Time Limit */ ++#define PCIE_ALTRT_ROUND_TRIP_LATENCY_LIMIT_S 0 ++#define PCIE_ALTRT_REPLAY_TIME_LIMIT 0xFFFF0000 /* Replay Time Limit */ ++#define PCIE_ALTRT_REPLAY_TIME_LIMIT_S 16 ++ ++/* Other Message Register */ ++#define PCIE_OMR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x704) ++ ++/* Port Force Link Register */ ++#define PCIE_PFLR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x708) ++#define PCIE_PFLR_LINK_NUM 0x000000FF /* Link Number */ ++#define PCIE_PFLR_LINK_NUM_S 0 ++#define PCIE_PFLR_FORCE_LINK 0x00008000 /* Force link */ ++#define PCIE_PFLR_LINK_STATE 0x003F0000 /* Link State */ ++#define PCIE_PFLR_LINK_STATE_S 16 ++#define PCIE_PFLR_LOW_POWER_ENTRY_CNT 0xFF000000 /* Low Power Entrance Count, only for EP */ ++#define PCIE_PFLR_LOW_POWER_ENTRY_CNT_S 24 ++ ++/* Ack Frequency Register */ ++#define PCIE_AFR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x70C) ++#define PCIE_AFR_AF 0x000000FF /* Ack Frequency */ ++#define PCIE_AFR_AF_S 0 ++#define PCIE_AFR_FTS_NUM 0x0000FF00 /* The number of Fast Training Sequence from L0S to L0 */ ++#define PCIE_AFR_FTS_NUM_S 8 ++#define PCIE_AFR_COM_FTS_NUM 0x00FF0000 /* N_FTS; when common clock is used*/ ++#define PCIE_AFR_COM_FTS_NUM_S 16 ++#define PCIE_AFR_L0S_ENTRY_LATENCY 0x07000000 /* L0s Entrance Latency */ ++#define PCIE_AFR_L0S_ENTRY_LATENCY_S 24 ++#define PCIE_AFR_L1_ENTRY_LATENCY 0x38000000 /* L1 Entrance Latency */ ++#define PCIE_AFR_L1_ENTRY_LATENCY_S 27 ++#define PCIE_AFR_FTS_NUM_DEFAULT 32 ++#define PCIE_AFR_L0S_ENTRY_LATENCY_DEFAULT 7 ++#define PCIE_AFR_L1_ENTRY_LATENCY_DEFAULT 5 ++ ++/* Port Link Control Register */ ++#define PCIE_PLCR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x710) ++#define PCIE_PLCR_OTHER_MSG_REQ 0x00000001 /* Other Message Request */ ++#define PCIE_PLCR_SCRAMBLE_DISABLE 0x00000002 /* Scramble Disable */ ++#define PCIE_PLCR_LOOPBACK_EN 0x00000004 /* Loopback Enable */ ++#define PCIE_PLCR_LTSSM_HOT_RST 0x00000008 /* Force LTSSM to the hot reset */ ++#define PCIE_PLCR_DLL_LINK_EN 0x00000020 /* Enable Link initialization */ ++#define PCIE_PLCR_FAST_LINK_SIM_EN 0x00000080 /* Sets all internal timers to fast mode for simulation purposes */ ++#define PCIE_PLCR_LINK_MODE 0x003F0000 /* Link Mode Enable Mask */ ++#define PCIE_PLCR_LINK_MODE_S 16 ++#define PCIE_PLCR_CORRUPTED_CRC_EN 0x02000000 /* Enabled Corrupt CRC */ ++ ++/* Lane Skew Register */ ++#define PCIE_LSR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x714) ++#define PCIE_LSR_LANE_SKEW_NUM 0x00FFFFFF /* Insert Lane Skew for Transmit, not applicable */ ++#define PCIE_LSR_LANE_SKEW_NUM_S 0 ++#define PCIE_LSR_FC_DISABLE 0x01000000 /* Disable of Flow Control */ ++#define PCIE_LSR_ACKNAK_DISABLE 0x02000000 /* Disable of Ack/Nak */ ++#define PCIE_LSR_LANE_DESKEW_DISABLE 0x80000000 /* Disable of Lane-to-Lane Skew */ ++ ++/* Symbol Number Register */ ++#define PCIE_SNR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x718) ++#define PCIE_SNR_TS 0x0000000F /* Number of TS Symbol */ ++#define PCIE_SNR_TS_S 0 ++#define PCIE_SNR_SKP 0x00000700 /* Number of SKP Symbol */ ++#define PCIE_SNR_SKP_S 8 ++#define PCIE_SNR_REPLAY_TIMER 0x0007C000 /* Timer Modifier for Replay Timer */ ++#define PCIE_SNR_REPLAY_TIMER_S 14 ++#define PCIE_SNR_ACKNAK_LATENCY_TIMER 0x00F80000 /* Timer Modifier for Ack/Nak Latency Timer */ ++#define PCIE_SNR_ACKNAK_LATENCY_TIMER_S 19 ++#define PCIE_SNR_FC_TIMER 0x1F000000 /* Timer Modifier for Flow Control Watchdog Timer */ ++#define PCIE_SNR_FC_TIMER_S 28 ++ ++/* Symbol Timer Register and Filter Mask Register 1 */ ++#define PCIE_STRFMR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x71C) ++#define PCIE_STRFMR_SKP_INTERVAL 0x000007FF /* SKP lnterval Value */ ++#define PCIE_STRFMR_SKP_INTERVAL_S 0 ++#define PCIE_STRFMR_FC_WDT_DISABLE 0x00008000 /* Disable of FC Watchdog Timer */ ++#define PCIE_STRFMR_TLP_FUNC_MISMATCH_OK 0x00010000 /* Mask Function Mismatch Filtering for Incoming Requests */ ++#define PCIE_STRFMR_POISONED_TLP_OK 0x00020000 /* Mask Poisoned TLP Filtering */ ++#define PCIE_STRFMR_BAR_MATCH_OK 0x00040000 /* Mask BAR Match Filtering */ ++#define PCIE_STRFMR_TYPE1_CFG_REQ_OK 0x00080000 /* Mask Type 1 Configuration Request Filtering */ ++#define PCIE_STRFMR_LOCKED_REQ_OK 0x00100000 /* Mask Locked Request Filtering */ ++#define PCIE_STRFMR_CPL_TAG_ERR_RULES_OK 0x00200000 /* Mask Tag Error Rules for Received Completions */ ++#define PCIE_STRFMR_CPL_REQUESTOR_ID_MISMATCH_OK 0x00400000 /* Mask Requester ID Mismatch Error for Received Completions */ ++#define PCIE_STRFMR_CPL_FUNC_MISMATCH_OK 0x00800000 /* Mask Function Mismatch Error for Received Completions */ ++#define PCIE_STRFMR_CPL_TC_MISMATCH_OK 0x01000000 /* Mask Traffic Class Mismatch Error for Received Completions */ ++#define PCIE_STRFMR_CPL_ATTR_MISMATCH_OK 0x02000000 /* Mask Attribute Mismatch Error for Received Completions */ ++#define PCIE_STRFMR_CPL_LENGTH_MISMATCH_OK 0x04000000 /* Mask Length Mismatch Error for Received Completions */ ++#define PCIE_STRFMR_TLP_ECRC_ERR_OK 0x08000000 /* Mask ECRC Error Filtering */ ++#define PCIE_STRFMR_CPL_TLP_ECRC_OK 0x10000000 /* Mask ECRC Error Filtering for Completions */ ++#define PCIE_STRFMR_RX_TLP_MSG_NO_DROP 0x20000000 /* Send Message TLPs */ ++#define PCIE_STRFMR_RX_IO_TRANS_ENABLE 0x40000000 /* Mask Filtering of received I/O Requests */ ++#define PCIE_STRFMR_RX_CFG_TRANS_ENABLE 0x80000000 /* Mask Filtering of Received Configuration Requests */ ++ ++#define PCIE_DEF_SKP_INTERVAL 700 /* 1180 ~1538 , 125MHz * 2, 250MHz * 1 */ ++ ++/* Filter Masker Register 2 */ ++#define PCIE_FMR2(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x720) ++#define PCIE_FMR2_VENDOR_MSG0_PASSED_TO_TRGT1 0x00000001 /* Mask RADM Filtering and Error Handling Rules */ ++#define PCIE_FMR2_VENDOR_MSG1_PASSED_TO_TRGT1 0x00000002 /* Mask RADM Filtering and Error Handling Rules */ ++ ++/* Debug Register 0 */ ++#define PCIE_DBR0(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x728) ++ ++/* Debug Register 1 */ ++#define PCIE_DBR1(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x72C) ++ ++/* Transmit Posted FC Credit Status Register */ ++#define PCIE_TPFCS(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x730) ++#define PCIE_TPFCS_TX_P_DATA_FC_CREDITS 0x00000FFF /* Transmit Posted Data FC Credits */ ++#define PCIE_TPFCS_TX_P_DATA_FC_CREDITS_S 0 ++#define PCIE_TPFCS_TX_P_HDR_FC_CREDITS 0x000FF000 /* Transmit Posted Header FC Credits */ ++#define PCIE_TPFCS_TX_P_HDR_FC_CREDITS_S 12 ++ ++/* Transmit Non-Posted FC Credit Status */ ++#define PCIE_TNPFCS(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x734) ++#define PCIE_TNPFCS_TX_NP_DATA_FC_CREDITS 0x00000FFF /* Transmit Non-Posted Data FC Credits */ ++#define PCIE_TNPFCS_TX_NP_DATA_FC_CREDITS_S 0 ++#define PCIE_TNPFCS_TX_NP_HDR_FC_CREDITS 0x000FF000 /* Transmit Non-Posted Header FC Credits */ ++#define PCIE_TNPFCS_TX_NP_HDR_FC_CREDITS_S 12 ++ ++/* Transmit Complete FC Credit Status Register */ ++#define PCIE_TCFCS(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x738) ++#define PCIE_TCFCS_TX_CPL_DATA_FC_CREDITS 0x00000FFF /* Transmit Completion Data FC Credits */ ++#define PCIE_TCFCS_TX_CPL_DATA_FC_CREDITS_S 0 ++#define PCIE_TCFCS_TX_CPL_HDR_FC_CREDITS 0x000FF000 /* Transmit Completion Header FC Credits */ ++#define PCIE_TCFCS_TX_CPL_HDR_FC_CREDITS_S 12 ++ ++/* Queue Status Register */ ++#define PCIE_QSR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x73C) ++#define PCIE_QSR_WAIT_UPDATE_FC_DLL 0x00000001 /* Received TLP FC Credits Not Returned */ ++#define PCIE_QSR_TX_RETRY_BUF_NOT_EMPTY 0x00000002 /* Transmit Retry Buffer Not Empty */ ++#define PCIE_QSR_RX_QUEUE_NOT_EMPTY 0x00000004 /* Received Queue Not Empty */ ++ ++/* VC Transmit Arbitration Register 1 */ ++#define PCIE_VCTAR1(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x740) ++#define PCIE_VCTAR1_WRR_WEIGHT_VC0 0x000000FF /* WRR Weight for VC0 */ ++#define PCIE_VCTAR1_WRR_WEIGHT_VC1 0x0000FF00 /* WRR Weight for VC1 */ ++#define PCIE_VCTAR1_WRR_WEIGHT_VC2 0x00FF0000 /* WRR Weight for VC2 */ ++#define PCIE_VCTAR1_WRR_WEIGHT_VC3 0xFF000000 /* WRR Weight for VC3 */ ++ ++/* VC Transmit Arbitration Register 2 */ ++#define PCIE_VCTAR2(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x744) ++#define PCIE_VCTAR2_WRR_WEIGHT_VC4 0x000000FF /* WRR Weight for VC4 */ ++#define PCIE_VCTAR2_WRR_WEIGHT_VC5 0x0000FF00 /* WRR Weight for VC5 */ ++#define PCIE_VCTAR2_WRR_WEIGHT_VC6 0x00FF0000 /* WRR Weight for VC6 */ ++#define PCIE_VCTAR2_WRR_WEIGHT_VC7 0xFF000000 /* WRR Weight for VC7 */ ++ ++/* VC0 Posted Receive Queue Control Register */ ++#define PCIE_VC0_PRQCR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x748) ++#define PCIE_VC0_PRQCR_P_DATA_CREDITS 0x00000FFF /* VC0 Posted Data Credits */ ++#define PCIE_VC0_PRQCR_P_DATA_CREDITS_S 0 ++#define PCIE_VC0_PRQCR_P_HDR_CREDITS 0x000FF000 /* VC0 Posted Header Credits */ ++#define PCIE_VC0_PRQCR_P_HDR_CREDITS_S 12 ++#define PCIE_VC0_PRQCR_P_TLP_QUEUE_MODE 0x00E00000 /* VC0 Posted TLP Queue Mode */ ++#define PCIE_VC0_PRQCR_P_TLP_QUEUE_MODE_S 20 ++#define PCIE_VC0_PRQCR_TLP_RELAX_ORDER 0x40000000 /* TLP Type Ordering for VC0 */ ++#define PCIE_VC0_PRQCR_VC_STRICT_ORDER 0x80000000 /* VC0 Ordering for Receive Queues */ ++ ++/* VC0 Non-Posted Receive Queue Control */ ++#define PCIE_VC0_NPRQCR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x74C) ++#define PCIE_VC0_NPRQCR_NP_DATA_CREDITS 0x00000FFF /* VC0 Non-Posted Data Credits */ ++#define PCIE_VC0_NPRQCR_NP_DATA_CREDITS_S 0 ++#define PCIE_VC0_NPRQCR_NP_HDR_CREDITS 0x000FF000 /* VC0 Non-Posted Header Credits */ ++#define PCIE_VC0_NPRQCR_NP_HDR_CREDITS_S 12 ++#define PCIE_VC0_NPRQCR_NP_TLP_QUEUE_MODE 0x00E00000 /* VC0 Non-Posted TLP Queue Mode */ ++#define PCIE_VC0_NPRQCR_NP_TLP_QUEUE_MODE_S 20 ++ ++/* VC0 Completion Receive Queue Control */ ++#define PCIE_VC0_CRQCR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x750) ++#define PCIE_VC0_CRQCR_CPL_DATA_CREDITS 0x00000FFF /* VC0 Completion TLP Queue Mode */ ++#define PCIE_VC0_CRQCR_CPL_DATA_CREDITS_S 0 ++#define PCIE_VC0_CRQCR_CPL_HDR_CREDITS 0x000FF000 /* VC0 Completion Header Credits */ ++#define PCIE_VC0_CRQCR_CPL_HDR_CREDITS_S 12 ++#define PCIE_VC0_CRQCR_CPL_TLP_QUEUE_MODE 0x00E00000 /* VC0 Completion Data Credits */ ++#define PCIE_VC0_CRQCR_CPL_TLP_QUEUE_MODE_S 21 ++ ++/* Applicable to the above three registers */ ++enum { ++ PCIE_VC0_TLP_QUEUE_MODE_STORE_FORWARD = 1, ++ PCIE_VC0_TLP_QUEUE_MODE_CUT_THROUGH = 2, ++ PCIE_VC0_TLP_QUEUE_MODE_BYPASS = 4, ++}; ++ ++/* VC0 Posted Buffer Depth Register */ ++#define PCIE_VC0_PBD(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x7A8) ++#define PCIE_VC0_PBD_P_DATA_QUEUE_ENTRIES 0x00003FFF /* VC0 Posted Data Queue Depth */ ++#define PCIE_VC0_PBD_P_DATA_QUEUE_ENTRIES_S 0 ++#define PCIE_VC0_PBD_P_HDR_QUEUE_ENTRIES 0x03FF0000 /* VC0 Posted Header Queue Depth */ ++#define PCIE_VC0_PBD_P_HDR_QUEUE_ENTRIES_S 16 ++ ++/* VC0 Non-Posted Buffer Depth Register */ ++#define PCIE_VC0_NPBD(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x7AC) ++#define PCIE_VC0_NPBD_NP_DATA_QUEUE_ENTRIES 0x00003FFF /* VC0 Non-Posted Data Queue Depth */ ++#define PCIE_VC0_NPBD_NP_DATA_QUEUE_ENTRIES_S 0 ++#define PCIE_VC0_NPBD_NP_HDR_QUEUE_ENTRIES 0x03FF0000 /* VC0 Non-Posted Header Queue Depth */ ++#define PCIE_VC0_NPBD_NP_HDR_QUEUE_ENTRIES_S 16 ++ ++/* VC0 Completion Buffer Depth Register */ ++#define PCIE_VC0_CBD(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x7B0) ++#define PCIE_VC0_CBD_CPL_DATA_QUEUE_ENTRIES 0x00003FFF /* C0 Completion Data Queue Depth */ ++#define PCIE_VC0_CBD_CPL_DATA_QUEUE_ENTRIES_S 0 ++#define PCIE_VC0_CBD_CPL_HDR_QUEUE_ENTRIES 0x03FF0000 /* VC0 Completion Header Queue Depth */ ++#define PCIE_VC0_CBD_CPL_HDR_QUEUE_ENTRIES_S 16 ++ ++/* PHY Status Register, all zeros in VR9 */ ++#define PCIE_PHYSR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x810) ++ ++/* PHY Control Register, all zeros in VR9 */ ++#define PCIE_PHYCR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x814) ++ ++/* ++ * PCIe PDI PHY register definition, suppose all the following ++ * stuff is confidential. ++ * XXX, detailed bit definition ++ */ ++#define PCIE_PHY_PLL_CTRL1(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x22 << 1)) ++#define PCIE_PHY_PLL_CTRL2(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x23 << 1)) ++#define PCIE_PHY_PLL_CTRL3(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x24 << 1)) ++#define PCIE_PHY_PLL_CTRL4(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x25 << 1)) ++#define PCIE_PHY_PLL_CTRL5(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x26 << 1)) ++#define PCIE_PHY_PLL_CTRL6(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x27 << 1)) ++#define PCIE_PHY_PLL_CTRL7(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x28 << 1)) ++#define PCIE_PHY_PLL_A_CTRL1(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x29 << 1)) ++#define PCIE_PHY_PLL_A_CTRL2(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x2A << 1)) ++#define PCIE_PHY_PLL_A_CTRL3(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x2B << 1)) ++#define PCIE_PHY_PLL_STATUS(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x2C << 1)) ++ ++#define PCIE_PHY_TX1_CTRL1(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x30 << 1)) ++#define PCIE_PHY_TX1_CTRL2(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x31 << 1)) ++#define PCIE_PHY_TX1_CTRL3(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x32 << 1)) ++#define PCIE_PHY_TX1_A_CTRL1(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x33 << 1)) ++#define PCIE_PHY_TX1_A_CTRL2(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x34 << 1)) ++#define PCIE_PHY_TX1_MOD1(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x35 << 1)) ++#define PCIE_PHY_TX1_MOD2(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x36 << 1)) ++#define PCIE_PHY_TX1_MOD3(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x37 << 1)) ++ ++#define PCIE_PHY_TX2_CTRL1(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x38 << 1)) ++#define PCIE_PHY_TX2_CTRL2(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x39 << 1)) ++#define PCIE_PHY_TX2_A_CTRL1(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x3B << 1)) ++#define PCIE_PHY_TX2_A_CTRL2(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x3C << 1)) ++#define PCIE_PHY_TX2_MOD1(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x3D << 1)) ++#define PCIE_PHY_TX2_MOD2(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x3E << 1)) ++#define PCIE_PHY_TX2_MOD3(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x3F << 1)) ++ ++#define PCIE_PHY_RX1_CTRL1(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x50 << 1)) ++#define PCIE_PHY_RX1_CTRL2(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x51 << 1)) ++#define PCIE_PHY_RX1_CDR(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x52 << 1)) ++#define PCIE_PHY_RX1_EI(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x53 << 1)) ++#define PCIE_PHY_RX1_A_CTRL(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x55 << 1)) ++ ++/* Interrupt related stuff */ ++#define PCIE_LEGACY_DISABLE 0 ++#define PCIE_LEGACY_INTA 1 ++#define PCIE_LEGACY_INTB 2 ++#define PCIE_LEGACY_INTC 3 ++#define PCIE_LEGACY_INTD 4 ++#define PCIE_LEGACY_INT_MAX PCIE_LEGACY_INTD ++ ++#endif /* IFXMIPS_PCIE_REG_H */ ++ +--- /dev/null ++++ b/arch/mips/pci/ifxmips_pcie_vr9.h +@@ -0,0 +1,269 @@ ++/**************************************************************************** ++ Copyright (c) 2010 ++ Lantiq Deutschland GmbH ++ Am Campeon 3; 85579 Neubiberg, Germany ++ ++ For licensing information, see the file 'LICENSE' in the root folder of ++ this software module. ++ ++ *****************************************************************************/ ++/*! ++ \file ifxmips_pcie_vr9.h ++ \ingroup IFX_PCIE ++ \brief PCIe RC driver vr9 specific file ++*/ ++ ++#ifndef IFXMIPS_PCIE_VR9_H ++#define IFXMIPS_PCIE_VR9_H ++ ++#include ++#include ++ ++#include ++#include ++ ++#define IFX_PCIE_GPIO_RESET 494 ++ ++#define IFX_REG_R32 ltq_r32 ++#define IFX_REG_W32 ltq_w32 ++#define CONFIG_IFX_PCIE_HW_SWAP ++#define IFX_RCU_AHB_ENDIAN ((volatile u32*)(IFX_RCU + 0x004C)) ++#define IFX_RCU_RST_REQ ((volatile u32*)(IFX_RCU + 0x0010)) ++#define IFX_RCU_AHB_BE_PCIE_PDI 0x00000080 /* Configure PCIE PDI module in big endian*/ ++ ++#define IFX_RCU (KSEG1 | 0x1F203000) ++#define IFX_RCU_AHB_BE_PCIE_M 0x00000001 /* Configure AHB master port that connects to PCIe RC in big endian */ ++#define IFX_RCU_AHB_BE_PCIE_S 0x00000010 /* Configure AHB slave port that connects to PCIe RC in little endian */ ++#define IFX_RCU_AHB_BE_XBAR_M 0x00000002 /* Configure AHB master port that connects to XBAR in big endian */ ++#define CONFIG_IFX_PCIE_PHY_36MHZ_MODE ++ ++#define IFX_PMU1_MODULE_PCIE_PHY (0) ++#define IFX_PMU1_MODULE_PCIE_CTRL (1) ++#define IFX_PMU1_MODULE_PDI (4) ++#define IFX_PMU1_MODULE_MSI (5) ++ ++#define IFX_PMU_MODULE_PCIE_L0_CLK (31) ++ ++ ++#define IFX_GPIO (KSEG1 | 0x1E100B00) ++#define ALT0 ((volatile u32*)(IFX_GPIO + 0x007c)) ++#define ALT1 ((volatile u32*)(IFX_GPIO + 0x0080)) ++#define OD ((volatile u32*)(IFX_GPIO + 0x0084)) ++#define DIR ((volatile u32*)(IFX_GPIO + 0x0078)) ++#define OUT ((volatile u32*)(IFX_GPIO + 0x0070)) ++ ++ ++static inline void pcie_ep_gpio_rst_init(int pcie_port) ++{ ++ ++ gpio_request(IFX_PCIE_GPIO_RESET, "pcie-reset"); ++ gpio_direction_output(IFX_PCIE_GPIO_RESET, 1); ++ gpio_set_value(IFX_PCIE_GPIO_RESET, 1); ++ ++/* ifx_gpio_pin_reserve(IFX_PCIE_GPIO_RESET, ifx_pcie_gpio_module_id); ++ ifx_gpio_output_set(IFX_PCIE_GPIO_RESET, ifx_pcie_gpio_module_id); ++ ifx_gpio_dir_out_set(IFX_PCIE_GPIO_RESET, ifx_pcie_gpio_module_id); ++ ifx_gpio_altsel0_clear(IFX_PCIE_GPIO_RESET, ifx_pcie_gpio_module_id); ++ ifx_gpio_altsel1_clear(IFX_PCIE_GPIO_RESET, ifx_pcie_gpio_module_id); ++ ifx_gpio_open_drain_set(IFX_PCIE_GPIO_RESET, ifx_pcie_gpio_module_id);*/ ++} ++ ++static inline void pcie_ahb_pmu_setup(void) ++{ ++ /* Enable AHB bus master/slave */ ++ struct clk *clk; ++ clk = clk_get_sys("1d900000.pcie", "ahb"); ++ clk_enable(clk); ++ ++ //AHBM_PMU_SETUP(IFX_PMU_ENABLE); ++ //AHBS_PMU_SETUP(IFX_PMU_ENABLE); ++} ++ ++static inline void pcie_rcu_endian_setup(int pcie_port) ++{ ++ u32 reg; ++ ++ reg = IFX_REG_R32(IFX_RCU_AHB_ENDIAN); ++#ifdef CONFIG_IFX_PCIE_HW_SWAP ++ reg |= IFX_RCU_AHB_BE_PCIE_M; ++ reg |= IFX_RCU_AHB_BE_PCIE_S; ++ reg &= ~IFX_RCU_AHB_BE_XBAR_M; ++#else ++ reg |= IFX_RCU_AHB_BE_PCIE_M; ++ reg &= ~IFX_RCU_AHB_BE_PCIE_S; ++ reg &= ~IFX_RCU_AHB_BE_XBAR_M; ++#endif /* CONFIG_IFX_PCIE_HW_SWAP */ ++ IFX_REG_W32(reg, IFX_RCU_AHB_ENDIAN); ++ IFX_PCIE_PRINT(PCIE_MSG_REG, "%s IFX_RCU_AHB_ENDIAN: 0x%08x\n", __func__, IFX_REG_R32(IFX_RCU_AHB_ENDIAN)); ++} ++ ++static inline void pcie_phy_pmu_enable(int pcie_port) ++{ ++ struct clk *clk; ++ clk = clk_get_sys("1d900000.pcie", "phy"); ++ clk_enable(clk); ++ ++ //PCIE_PHY_PMU_SETUP(IFX_PMU_ENABLE); ++} ++ ++static inline void pcie_phy_pmu_disable(int pcie_port) ++{ ++ struct clk *clk; ++ clk = clk_get_sys("1d900000.pcie", "phy"); ++ clk_disable(clk); ++ ++// PCIE_PHY_PMU_SETUP(IFX_PMU_DISABLE); ++} ++ ++static inline void pcie_pdi_big_endian(int pcie_port) ++{ ++ u32 reg; ++ ++ /* SRAM2PDI endianness control. */ ++ reg = IFX_REG_R32(IFX_RCU_AHB_ENDIAN); ++ /* Config AHB->PCIe and PDI endianness */ ++ reg |= IFX_RCU_AHB_BE_PCIE_PDI; ++ IFX_REG_W32(reg, IFX_RCU_AHB_ENDIAN); ++} ++ ++static inline void pcie_pdi_pmu_enable(int pcie_port) ++{ ++ /* Enable PDI to access PCIe PHY register */ ++ struct clk *clk; ++ clk = clk_get_sys("1d900000.pcie", "pdi"); ++ clk_enable(clk); ++ //PDI_PMU_SETUP(IFX_PMU_ENABLE); ++} ++ ++static inline void pcie_core_rst_assert(int pcie_port) ++{ ++ u32 reg; ++ ++ reg = IFX_REG_R32(IFX_RCU_RST_REQ); ++ ++ /* Reset PCIe PHY & Core, bit 22, bit 26 may be affected if write it directly */ ++ reg |= 0x00400000; ++ IFX_REG_W32(reg, IFX_RCU_RST_REQ); ++} ++ ++static inline void pcie_core_rst_deassert(int pcie_port) ++{ ++ u32 reg; ++ ++ /* Make sure one micro-second delay */ ++ udelay(1); ++ ++ /* Reset PCIe PHY & Core, bit 22 */ ++ reg = IFX_REG_R32(IFX_RCU_RST_REQ); ++ reg &= ~0x00400000; ++ IFX_REG_W32(reg, IFX_RCU_RST_REQ); ++} ++ ++static inline void pcie_phy_rst_assert(int pcie_port) ++{ ++ u32 reg; ++ ++ reg = IFX_REG_R32(IFX_RCU_RST_REQ); ++ reg |= 0x00001000; /* Bit 12 */ ++ IFX_REG_W32(reg, IFX_RCU_RST_REQ); ++} ++ ++static inline void pcie_phy_rst_deassert(int pcie_port) ++{ ++ u32 reg; ++ ++ /* Make sure one micro-second delay */ ++ udelay(1); ++ ++ reg = IFX_REG_R32(IFX_RCU_RST_REQ); ++ reg &= ~0x00001000; /* Bit 12 */ ++ IFX_REG_W32(reg, IFX_RCU_RST_REQ); ++} ++ ++static inline void pcie_device_rst_assert(int pcie_port) ++{ ++ gpio_set_value(IFX_PCIE_GPIO_RESET, 0); ++// ifx_gpio_output_clear(IFX_PCIE_GPIO_RESET, ifx_pcie_gpio_module_id); ++} ++ ++static inline void pcie_device_rst_deassert(int pcie_port) ++{ ++ mdelay(100); ++ gpio_direction_output(IFX_PCIE_GPIO_RESET, 1); ++// gpio_set_value(IFX_PCIE_GPIO_RESET, 1); ++ //ifx_gpio_output_set(IFX_PCIE_GPIO_RESET, ifx_pcie_gpio_module_id); ++} ++ ++static inline void pcie_core_pmu_setup(int pcie_port) ++{ ++ struct clk *clk; ++ clk = clk_get_sys("1d900000.pcie", "ctl"); ++ clk_enable(clk); ++ clk = clk_get_sys("1d900000.pcie", "bus"); ++ clk_enable(clk); ++ ++ /* PCIe Core controller enabled */ ++// PCIE_CTRL_PMU_SETUP(IFX_PMU_ENABLE); ++ ++ /* Enable PCIe L0 Clock */ ++// PCIE_L0_CLK_PMU_SETUP(IFX_PMU_ENABLE); ++} ++ ++static inline void pcie_msi_init(int pcie_port) ++{ ++ struct clk *clk; ++ pcie_msi_pic_init(pcie_port); ++ clk = clk_get_sys("ltq_pcie", "msi"); ++ clk_enable(clk); ++// MSI_PMU_SETUP(IFX_PMU_ENABLE); ++} ++ ++static inline u32 ++ifx_pcie_bus_nr_deduct(u32 bus_number, int pcie_port) ++{ ++ u32 tbus_number = bus_number; ++ ++#ifdef CONFIG_PCI_LANTIQ ++ if (pcibios_host_nr() > 1) { ++ tbus_number -= pcibios_1st_host_bus_nr(); ++ } ++#endif /* CONFIG_PCI_LANTIQ */ ++ return tbus_number; ++} ++ ++static inline u32 ++ifx_pcie_bus_enum_hack(struct pci_bus *bus, u32 devfn, int where, u32 value, int pcie_port, int read) ++{ ++ struct pci_dev *pdev; ++ u32 tvalue = value; ++ ++ /* Sanity check */ ++ pdev = pci_get_slot(bus, devfn); ++ if (pdev == NULL) { ++ return tvalue; ++ } ++ ++ /* Only care about PCI bridge */ ++ if (pdev->hdr_type != PCI_HEADER_TYPE_BRIDGE) { ++ return tvalue; ++ } ++ ++ if (read) { /* Read hack */ ++ #ifdef CONFIG_PCI_LANTIQ ++ if (pcibios_host_nr() > 1) { ++ tvalue = ifx_pcie_bus_enum_read_hack(where, tvalue); ++ } ++ #endif /* CONFIG_PCI_LANTIQ */ ++ } ++ else { /* Write hack */ ++ #ifdef CONFIG_PCI_LANTIQ ++ if (pcibios_host_nr() > 1) { ++ tvalue = ifx_pcie_bus_enum_write_hack(where, tvalue); ++ } ++ #endif ++ } ++ return tvalue; ++} ++ ++#endif /* IFXMIPS_PCIE_VR9_H */ ++ +--- a/arch/mips/pci/pci-legacy.c ++++ b/arch/mips/pci/pci-legacy.c +@@ -313,3 +313,30 @@ char *__init pcibios_setup(char *str) + return pcibios_plat_setup(str); + return str; + } ++ ++int pcibios_host_nr(void) ++{ ++ int count = 0; ++ struct pci_controller *hose; ++ list_for_each_entry(hose, &controllers, list) { ++ count++; ++ } ++ return count; ++} ++EXPORT_SYMBOL(pcibios_host_nr); ++ ++int pcibios_1st_host_bus_nr(void) ++{ ++ int bus_nr = 0; ++ struct pci_controller *hose; ++ ++ hose = list_first_entry_or_null(&controllers, struct pci_controller, list); ++ ++ if (hose != NULL) { ++ if (hose->bus != NULL) { ++ bus_nr = hose->bus->number + 1; ++ } ++ } ++ return bus_nr; ++} ++EXPORT_SYMBOL(pcibios_1st_host_bus_nr); +--- /dev/null ++++ b/arch/mips/pci/pcie-lantiq.h +@@ -0,0 +1,1305 @@ ++/****************************************************************************** ++** ++** FILE NAME : ifxmips_pcie_reg.h ++** PROJECT : IFX UEIP for VRX200 ++** MODULES : PCIe module ++** ++** DATE : 02 Mar 2009 ++** AUTHOR : Lei Chuanhua ++** DESCRIPTION : PCIe Root Complex Driver ++** COPYRIGHT : Copyright (c) 2009 ++** Infineon Technologies AG ++** Am Campeon 1-12, 85579 Neubiberg, Germany ++** ++** This program is free software; you can redistribute it and/or modify ++** it under the terms of the GNU General Public License as published by ++** the Free Software Foundation; either version 2 of the License, or ++** (at your option) any later version. ++** HISTORY ++** $Version $Date $Author $Comment ++** 0.0.1 17 Mar,2009 Lei Chuanhua Initial version ++*******************************************************************************/ ++#ifndef IFXMIPS_PCIE_REG_H ++#define IFXMIPS_PCIE_REG_H ++#include ++#include ++#include ++#include ++/*! ++ \file ifxmips_pcie_reg.h ++ \ingroup IFX_PCIE ++ \brief header file for PCIe module register definition ++*/ ++/* PCIe Address Mapping Base */ ++#define PCIE_CFG_PHY_BASE 0x1D000000UL ++#define PCIE_CFG_BASE (KSEG1 + PCIE_CFG_PHY_BASE) ++#define PCIE_CFG_SIZE (8 * 1024 * 1024) ++ ++#define PCIE_MEM_PHY_BASE 0x1C000000UL ++#define PCIE_MEM_BASE (KSEG1 + PCIE_MEM_PHY_BASE) ++#define PCIE_MEM_SIZE (16 * 1024 * 1024) ++#define PCIE_MEM_PHY_END (PCIE_MEM_PHY_BASE + PCIE_MEM_SIZE - 1) ++ ++#define PCIE_IO_PHY_BASE 0x1D800000UL ++#define PCIE_IO_BASE (KSEG1 + PCIE_IO_PHY_BASE) ++#define PCIE_IO_SIZE (1 * 1024 * 1024) ++#define PCIE_IO_PHY_END (PCIE_IO_PHY_BASE + PCIE_IO_SIZE - 1) ++ ++#define PCIE_RC_CFG_BASE (KSEG1 + 0x1D900000) ++#define PCIE_APP_LOGIC_REG (KSEG1 + 0x1E100900) ++#define PCIE_MSI_PHY_BASE 0x1F600000UL ++ ++#define PCIE_PDI_PHY_BASE 0x1F106800UL ++#define PCIE_PDI_BASE (KSEG1 + PCIE_PDI_PHY_BASE) ++#define PCIE_PDI_SIZE 0x400 ++ ++#define PCIE1_CFG_PHY_BASE 0x19000000UL ++#define PCIE1_CFG_BASE (KSEG1 + PCIE1_CFG_PHY_BASE) ++#define PCIE1_CFG_SIZE (8 * 1024 * 1024) ++ ++#define PCIE1_MEM_PHY_BASE 0x18000000UL ++#define PCIE1_MEM_BASE (KSEG1 + PCIE1_MEM_PHY_BASE) ++#define PCIE1_MEM_SIZE (16 * 1024 * 1024) ++#define PCIE1_MEM_PHY_END (PCIE1_MEM_PHY_BASE + PCIE1_MEM_SIZE - 1) ++ ++#define PCIE1_IO_PHY_BASE 0x19800000UL ++#define PCIE1_IO_BASE (KSEG1 + PCIE1_IO_PHY_BASE) ++#define PCIE1_IO_SIZE (1 * 1024 * 1024) ++#define PCIE1_IO_PHY_END (PCIE1_IO_PHY_BASE + PCIE1_IO_SIZE - 1) ++ ++#define PCIE1_RC_CFG_BASE (KSEG1 + 0x19900000) ++#define PCIE1_APP_LOGIC_REG (KSEG1 + 0x1E100700) ++#define PCIE1_MSI_PHY_BASE 0x1F400000UL ++ ++#define PCIE1_PDI_PHY_BASE 0x1F700400UL ++#define PCIE1_PDI_BASE (KSEG1 + PCIE1_PDI_PHY_BASE) ++#define PCIE1_PDI_SIZE 0x400 ++ ++#define PCIE_CFG_PORT_TO_BASE(X) ((X) > 0 ? (PCIE1_CFG_BASE) : (PCIE_CFG_BASE)) ++#define PCIE_MEM_PORT_TO_BASE(X) ((X) > 0 ? (PCIE1_MEM_BASE) : (PCIE_MEM_BASE)) ++#define PCIE_IO_PORT_TO_BASE(X) ((X) > 0 ? (PCIE1_IO_BASE) : (PCIE_IO_BASE)) ++#define PCIE_MEM_PHY_PORT_TO_BASE(X) ((X) > 0 ? (PCIE1_MEM_PHY_BASE) : (PCIE_MEM_PHY_BASE)) ++#define PCIE_MEM_PHY_PORT_TO_END(X) ((X) > 0 ? (PCIE1_MEM_PHY_END) : (PCIE_MEM_PHY_END)) ++#define PCIE_IO_PHY_PORT_TO_BASE(X) ((X) > 0 ? (PCIE1_IO_PHY_BASE) : (PCIE_IO_PHY_BASE)) ++#define PCIE_IO_PHY_PORT_TO_END(X) ((X) > 0 ? (PCIE1_IO_PHY_END) : (PCIE_IO_PHY_END)) ++#define PCIE_APP_PORT_TO_BASE(X) ((X) > 0 ? (PCIE1_APP_LOGIC_REG) : (PCIE_APP_LOGIC_REG)) ++#define PCIE_RC_PORT_TO_BASE(X) ((X) > 0 ? (PCIE1_RC_CFG_BASE) : (PCIE_RC_CFG_BASE)) ++#define PCIE_PHY_PORT_TO_BASE(X) ((X) > 0 ? (PCIE1_PDI_BASE) : (PCIE_PDI_BASE)) ++ ++/* PCIe Application Logic Register */ ++/* RC Core Control Register */ ++#define PCIE_RC_CCR(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x10) ++/* This should be enabled after initializing configuratin registers ++ * Also should check link status retraining bit ++ */ ++#define PCIE_RC_CCR_LTSSM_ENABLE 0x00000001 /* Enable LTSSM to continue link establishment */ ++ ++/* RC Core Debug Register */ ++#define PCIE_RC_DR(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x14) ++#define PCIE_RC_DR_DLL_UP 0x00000001 /* Data Link Layer Up */ ++#define PCIE_RC_DR_CURRENT_POWER_STATE 0x0000000E /* Current Power State */ ++#define PCIE_RC_DR_CURRENT_POWER_STATE_S 1 ++#define PCIE_RC_DR_CURRENT_LTSSM_STATE 0x000001F0 /* Current LTSSM State */ ++#define PCIE_RC_DR_CURRENT_LTSSM_STATE_S 4 ++ ++#define PCIE_RC_DR_PM_DEV_STATE 0x00000E00 /* Power Management D-State */ ++#define PCIE_RC_DR_PM_DEV_STATE_S 9 ++ ++#define PCIE_RC_DR_PM_ENABLED 0x00001000 /* Power Management State from PMU */ ++#define PCIE_RC_DR_PME_EVENT_ENABLED 0x00002000 /* Power Management Event Enable State */ ++#define PCIE_RC_DR_AUX_POWER_ENABLED 0x00004000 /* Auxiliary Power Enable */ ++ ++/* Current Power State Definition */ ++enum { ++ PCIE_RC_DR_D0 = 0, ++ PCIE_RC_DR_D1, /* Not supported */ ++ PCIE_RC_DR_D2, /* Not supported */ ++ PCIE_RC_DR_D3, ++ PCIE_RC_DR_UN, ++}; ++ ++/* PHY Link Status Register */ ++#define PCIE_PHY_SR(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x18) ++#define PCIE_PHY_SR_PHY_LINK_UP 0x00000001 /* PHY Link Up/Down Indicator */ ++ ++/* Electromechanical Control Register */ ++#define PCIE_EM_CR(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x1C) ++#define PCIE_EM_CR_CARD_IS_PRESENT 0x00000001 /* Card Presence Detect State */ ++#define PCIE_EM_CR_MRL_OPEN 0x00000002 /* MRL Sensor State */ ++#define PCIE_EM_CR_POWER_FAULT_SET 0x00000004 /* Power Fault Detected */ ++#define PCIE_EM_CR_MRL_SENSOR_SET 0x00000008 /* MRL Sensor Changed */ ++#define PCIE_EM_CR_PRESENT_DETECT_SET 0x00000010 /* Card Presense Detect Changed */ ++#define PCIE_EM_CR_CMD_CPL_INT_SET 0x00000020 /* Command Complete Interrupt */ ++#define PCIE_EM_CR_SYS_INTERLOCK_SET 0x00000040 /* System Electromechanical IterLock Engaged */ ++#define PCIE_EM_CR_ATTENTION_BUTTON_SET 0x00000080 /* Attention Button Pressed */ ++ ++/* Interrupt Status Register */ ++#define PCIE_IR_SR(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x20) ++#define PCIE_IR_SR_PME_CAUSE_MSI 0x00000002 /* MSI caused by PME */ ++#define PCIE_IR_SR_HP_PME_WAKE_GEN 0x00000004 /* Hotplug PME Wake Generation */ ++#define PCIE_IR_SR_HP_MSI 0x00000008 /* Hotplug MSI */ ++#define PCIE_IR_SR_AHB_LU_ERR 0x00000030 /* AHB Bridge Lookup Error Signals */ ++#define PCIE_IR_SR_AHB_LU_ERR_S 4 ++#define PCIE_IR_SR_INT_MSG_NUM 0x00003E00 /* Interrupt Message Number */ ++#define PCIE_IR_SR_INT_MSG_NUM_S 9 ++#define PCIE_IR_SR_AER_INT_MSG_NUM 0xF8000000 /* Advanced Error Interrupt Message Number */ ++#define PCIE_IR_SR_AER_INT_MSG_NUM_S 27 ++ ++/* Message Control Register */ ++#define PCIE_MSG_CR(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x30) ++#define PCIE_MSG_CR_GEN_PME_TURN_OFF_MSG 0x00000001 /* Generate PME Turn Off Message */ ++#define PCIE_MSG_CR_GEN_UNLOCK_MSG 0x00000002 /* Generate Unlock Message */ ++ ++#define PCIE_VDM_DR(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x34) ++ ++/* Vendor-Defined Message Requester ID Register */ ++#define PCIE_VDM_RID(X) (PCIE_APP_PORT_TO_BASE (X) + 0x38) ++#define PCIE_VDM_RID_VENROR_MSG_REQ_ID 0x0000FFFF ++#define PCIE_VDM_RID_VDMRID_S 0 ++ ++/* ASPM Control Register */ ++#define PCIE_ASPM_CR(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x40) ++#define PCIE_ASPM_CR_HOT_RST 0x00000001 /* Hot Reset Request to the downstream device */ ++#define PCIE_ASPM_CR_REQ_EXIT_L1 0x00000002 /* Request to Exit L1 */ ++#define PCIE_ASPM_CR_REQ_ENTER_L1 0x00000004 /* Request to Enter L1 */ ++ ++/* Vendor Message DW0 Register */ ++#define PCIE_VM_MSG_DW0(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x50) ++#define PCIE_VM_MSG_DW0_TYPE 0x0000001F /* Message type */ ++#define PCIE_VM_MSG_DW0_TYPE_S 0 ++#define PCIE_VM_MSG_DW0_FORMAT 0x00000060 /* Format */ ++#define PCIE_VM_MSG_DW0_FORMAT_S 5 ++#define PCIE_VM_MSG_DW0_TC 0x00007000 /* Traffic Class */ ++#define PCIE_VM_MSG_DW0_TC_S 12 ++#define PCIE_VM_MSG_DW0_ATTR 0x000C0000 /* Atrributes */ ++#define PCIE_VM_MSG_DW0_ATTR_S 18 ++#define PCIE_VM_MSG_DW0_EP_TLP 0x00100000 /* Poisoned TLP */ ++#define PCIE_VM_MSG_DW0_TD 0x00200000 /* TLP Digest */ ++#define PCIE_VM_MSG_DW0_LEN 0xFFC00000 /* Length */ ++#define PCIE_VM_MSG_DW0_LEN_S 22 ++ ++/* Format Definition */ ++enum { ++ PCIE_VM_MSG_FORMAT_00 = 0, /* 3DW Hdr, no data*/ ++ PCIE_VM_MSG_FORMAT_01, /* 4DW Hdr, no data */ ++ PCIE_VM_MSG_FORMAT_10, /* 3DW Hdr, with data */ ++ PCIE_VM_MSG_FORMAT_11, /* 4DW Hdr, with data */ ++}; ++ ++/* Traffic Class Definition */ ++enum { ++ PCIE_VM_MSG_TC0 = 0, ++ PCIE_VM_MSG_TC1, ++ PCIE_VM_MSG_TC2, ++ PCIE_VM_MSG_TC3, ++ PCIE_VM_MSG_TC4, ++ PCIE_VM_MSG_TC5, ++ PCIE_VM_MSG_TC6, ++ PCIE_VM_MSG_TC7, ++}; ++ ++/* Attributes Definition */ ++enum { ++ PCIE_VM_MSG_ATTR_00 = 0, /* RO and No Snoop cleared */ ++ PCIE_VM_MSG_ATTR_01, /* RO cleared , No Snoop set */ ++ PCIE_VM_MSG_ATTR_10, /* RO set, No Snoop cleared*/ ++ PCIE_VM_MSG_ATTR_11, /* RO and No Snoop set */ ++}; ++ ++/* Payload Size Definition */ ++#define PCIE_VM_MSG_LEN_MIN 0 ++#define PCIE_VM_MSG_LEN_MAX 1024 ++ ++/* Vendor Message DW1 Register */ ++#define PCIE_VM_MSG_DW1(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x54) ++#define PCIE_VM_MSG_DW1_FUNC_NUM 0x00000070 /* Function Number */ ++#define PCIE_VM_MSG_DW1_FUNC_NUM_S 8 ++#define PCIE_VM_MSG_DW1_CODE 0x00FF0000 /* Message Code */ ++#define PCIE_VM_MSG_DW1_CODE_S 16 ++#define PCIE_VM_MSG_DW1_TAG 0xFF000000 /* Tag */ ++#define PCIE_VM_MSG_DW1_TAG_S 24 ++ ++#define PCIE_VM_MSG_DW2(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x58) ++#define PCIE_VM_MSG_DW3(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x5C) ++ ++/* Vendor Message Request Register */ ++#define PCIE_VM_MSG_REQR(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x60) ++#define PCIE_VM_MSG_REQR_REQ 0x00000001 /* Vendor Message Request */ ++ ++ ++/* AHB Slave Side Band Control Register */ ++#define PCIE_AHB_SSB(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x70) ++#define PCIE_AHB_SSB_REQ_BCM 0x00000001 /* Slave Reques BCM filed */ ++#define PCIE_AHB_SSB_REQ_EP 0x00000002 /* Slave Reques EP filed */ ++#define PCIE_AHB_SSB_REQ_TD 0x00000004 /* Slave Reques TD filed */ ++#define PCIE_AHB_SSB_REQ_ATTR 0x00000018 /* Slave Reques Attribute number */ ++#define PCIE_AHB_SSB_REQ_ATTR_S 3 ++#define PCIE_AHB_SSB_REQ_TC 0x000000E0 /* Slave Request TC Field */ ++#define PCIE_AHB_SSB_REQ_TC_S 5 ++ ++/* AHB Master SideBand Ctrl Register */ ++#define PCIE_AHB_MSB(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x74) ++#define PCIE_AHB_MSB_RESP_ATTR 0x00000003 /* Master Response Attribute number */ ++#define PCIE_AHB_MSB_RESP_ATTR_S 0 ++#define PCIE_AHB_MSB_RESP_BAD_EOT 0x00000004 /* Master Response Badeot filed */ ++#define PCIE_AHB_MSB_RESP_BCM 0x00000008 /* Master Response BCM filed */ ++#define PCIE_AHB_MSB_RESP_EP 0x00000010 /* Master Response EP filed */ ++#define PCIE_AHB_MSB_RESP_TD 0x00000020 /* Master Response TD filed */ ++#define PCIE_AHB_MSB_RESP_FUN_NUM 0x000003C0 /* Master Response Function number */ ++#define PCIE_AHB_MSB_RESP_FUN_NUM_S 6 ++ ++/* AHB Control Register, fixed bus enumeration exception */ ++#define PCIE_AHB_CTRL(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0x78) ++#define PCIE_AHB_CTRL_BUS_ERROR_SUPPRESS 0x00000001 ++ ++/* Interrupt Enalbe Register */ ++#define PCIE_IRNEN(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0xF4) ++#define PCIE_IRNCR(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0xF8) ++#define PCIE_IRNICR(X) (volatile u32*)(PCIE_APP_PORT_TO_BASE(X) + 0xFC) ++ ++/* PCIe interrupt enable/control/capture register definition */ ++#define PCIE_IRN_AER_REPORT 0x00000001 /* AER Interrupt */ ++#define PCIE_IRN_AER_MSIX 0x00000002 /* Advanced Error MSI-X Interrupt */ ++#define PCIE_IRN_PME 0x00000004 /* PME Interrupt */ ++#define PCIE_IRN_HOTPLUG 0x00000008 /* Hotplug Interrupt */ ++#define PCIE_IRN_RX_VDM_MSG 0x00000010 /* Vendor-Defined Message Interrupt */ ++#define PCIE_IRN_RX_CORRECTABLE_ERR_MSG 0x00000020 /* Correctable Error Message Interrupt */ ++#define PCIE_IRN_RX_NON_FATAL_ERR_MSG 0x00000040 /* Non-fatal Error Message */ ++#define PCIE_IRN_RX_FATAL_ERR_MSG 0x00000080 /* Fatal Error Message */ ++#define PCIE_IRN_RX_PME_MSG 0x00000100 /* PME Message Interrupt */ ++#define PCIE_IRN_RX_PME_TURNOFF_ACK 0x00000200 /* PME Turnoff Ack Message Interrupt */ ++#define PCIE_IRN_AHB_BR_FATAL_ERR 0x00000400 /* AHB Fatal Error Interrupt */ ++#define PCIE_IRN_LINK_AUTO_BW_STATUS 0x00000800 /* Link Auto Bandwidth Status Interrupt */ ++#define PCIE_IRN_BW_MGT 0x00001000 /* Bandwidth Managment Interrupt */ ++#define PCIE_IRN_INTA 0x00002000 /* INTA */ ++#define PCIE_IRN_INTB 0x00004000 /* INTB */ ++#define PCIE_IRN_INTC 0x00008000 /* INTC */ ++#define PCIE_IRN_INTD 0x00010000 /* INTD */ ++#define PCIE_IRN_WAKEUP 0x00020000 /* Wake up Interrupt */ ++ ++#define PCIE_RC_CORE_COMBINED_INT (PCIE_IRN_AER_REPORT | PCIE_IRN_AER_MSIX | PCIE_IRN_PME | \ ++ PCIE_IRN_HOTPLUG | PCIE_IRN_RX_VDM_MSG | PCIE_IRN_RX_CORRECTABLE_ERR_MSG |\ ++ PCIE_IRN_RX_NON_FATAL_ERR_MSG | PCIE_IRN_RX_FATAL_ERR_MSG | \ ++ PCIE_IRN_RX_PME_MSG | PCIE_IRN_RX_PME_TURNOFF_ACK | PCIE_IRN_AHB_BR_FATAL_ERR | \ ++ PCIE_IRN_LINK_AUTO_BW_STATUS | PCIE_IRN_BW_MGT) ++/* PCIe RC Configuration Register */ ++#define PCIE_VDID(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x00) ++ ++/* Bit definition from pci_reg.h */ ++#define PCIE_PCICMDSTS(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x04) ++#define PCIE_CCRID(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x08) ++#define PCIE_CLSLTHTBR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x0C) /* EP only */ ++/* BAR0, BAR1,Only necessary if the bridges implements a device-specific register set or memory buffer */ ++#define PCIE_BAR0(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x10) /* Not used*/ ++#define PCIE_BAR1(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x14) /* Not used */ ++ ++#define PCIE_BNR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x18) /* Mandatory */ ++/* Bus Number Register bits */ ++#define PCIE_BNR_PRIMARY_BUS_NUM 0x000000FF ++#define PCIE_BNR_PRIMARY_BUS_NUM_S 0 ++#define PCIE_PNR_SECONDARY_BUS_NUM 0x0000FF00 ++#define PCIE_PNR_SECONDARY_BUS_NUM_S 8 ++#define PCIE_PNR_SUB_BUS_NUM 0x00FF0000 ++#define PCIE_PNR_SUB_BUS_NUM_S 16 ++ ++/* IO Base/Limit Register bits */ ++#define PCIE_IOBLSECS(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x1C) /* RC only */ ++#define PCIE_IOBLSECS_32BIT_IO_ADDR 0x00000001 ++#define PCIE_IOBLSECS_IO_BASE_ADDR 0x000000F0 ++#define PCIE_IOBLSECS_IO_BASE_ADDR_S 4 ++#define PCIE_IOBLSECS_32BIT_IOLIMT 0x00000100 ++#define PCIE_IOBLSECS_IO_LIMIT_ADDR 0x0000F000 ++#define PCIE_IOBLSECS_IO_LIMIT_ADDR_S 12 ++ ++/* Non-prefetchable Memory Base/Limit Register bit */ ++#define PCIE_MBML(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x20) /* RC only */ ++#define PCIE_MBML_MEM_BASE_ADDR 0x0000FFF0 ++#define PCIE_MBML_MEM_BASE_ADDR_S 4 ++#define PCIE_MBML_MEM_LIMIT_ADDR 0xFFF00000 ++#define PCIE_MBML_MEM_LIMIT_ADDR_S 20 ++ ++/* Prefetchable Memory Base/Limit Register bit */ ++#define PCIE_PMBL(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x24) /* RC only */ ++#define PCIE_PMBL_64BIT_ADDR 0x00000001 ++#define PCIE_PMBL_UPPER_12BIT 0x0000FFF0 ++#define PCIE_PMBL_UPPER_12BIT_S 4 ++#define PCIE_PMBL_E64MA 0x00010000 ++#define PCIE_PMBL_END_ADDR 0xFFF00000 ++#define PCIE_PMBL_END_ADDR_S 20 ++#define PCIE_PMBU32(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x28) /* RC only */ ++#define PCIE_PMLU32(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x2C) /* RC only */ ++ ++/* I/O Base/Limit Upper 16 bits register */ ++#define PCIE_IO_BANDL(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x30) /* RC only */ ++#define PCIE_IO_BANDL_UPPER_16BIT_IO_BASE 0x0000FFFF ++#define PCIE_IO_BANDL_UPPER_16BIT_IO_BASE_S 0 ++#define PCIE_IO_BANDL_UPPER_16BIT_IO_LIMIT 0xFFFF0000 ++#define PCIE_IO_BANDL_UPPER_16BIT_IO_LIMIT_S 16 ++ ++#define PCIE_CPR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x34) ++#define PCIE_EBBAR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x38) ++ ++/* Interrupt and Secondary Bridge Control Register */ ++#define PCIE_INTRBCTRL(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x3C) ++ ++#define PCIE_INTRBCTRL_INT_LINE 0x000000FF ++#define PCIE_INTRBCTRL_INT_LINE_S 0 ++#define PCIE_INTRBCTRL_INT_PIN 0x0000FF00 ++#define PCIE_INTRBCTRL_INT_PIN_S 8 ++#define PCIE_INTRBCTRL_PARITY_ERR_RESP_ENABLE 0x00010000 /* #PERR */ ++#define PCIE_INTRBCTRL_SERR_ENABLE 0x00020000 /* #SERR */ ++#define PCIE_INTRBCTRL_ISA_ENABLE 0x00040000 /* ISA enable, IO 64KB only */ ++#define PCIE_INTRBCTRL_VGA_ENABLE 0x00080000 /* VGA enable */ ++#define PCIE_INTRBCTRL_VGA_16BIT_DECODE 0x00100000 /* VGA 16bit decode */ ++#define PCIE_INTRBCTRL_RST_SECONDARY_BUS 0x00400000 /* Secondary bus rest, hot rest, 1ms */ ++/* Others are read only */ ++enum { ++ PCIE_INTRBCTRL_INT_NON = 0, ++ PCIE_INTRBCTRL_INTA, ++ PCIE_INTRBCTRL_INTB, ++ PCIE_INTRBCTRL_INTC, ++ PCIE_INTRBCTRL_INTD, ++}; ++ ++#define PCIE_PM_CAPR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x40) ++ ++/* Power Management Control and Status Register */ ++#define PCIE_PM_CSR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x44) ++ ++#define PCIE_PM_CSR_POWER_STATE 0x00000003 /* Power State */ ++#define PCIE_PM_CSR_POWER_STATE_S 0 ++#define PCIE_PM_CSR_SW_RST 0x00000008 /* Soft Reset Enabled */ ++#define PCIE_PM_CSR_PME_ENABLE 0x00000100 /* PME Enable */ ++#define PCIE_PM_CSR_PME_STATUS 0x00008000 /* PME status */ ++ ++/* MSI Capability Register for EP */ ++#define PCIE_MCAPR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x50) ++ ++#define PCIE_MCAPR_MSI_CAP_ID 0x000000FF /* MSI Capability ID */ ++#define PCIE_MCAPR_MSI_CAP_ID_S 0 ++#define PCIE_MCAPR_MSI_NEXT_CAP_PTR 0x0000FF00 /* Next Capability Pointer */ ++#define PCIE_MCAPR_MSI_NEXT_CAP_PTR_S 8 ++#define PCIE_MCAPR_MSI_ENABLE 0x00010000 /* MSI Enable */ ++#define PCIE_MCAPR_MULTI_MSG_CAP 0x000E0000 /* Multiple Message Capable */ ++#define PCIE_MCAPR_MULTI_MSG_CAP_S 17 ++#define PCIE_MCAPR_MULTI_MSG_ENABLE 0x00700000 /* Multiple Message Enable */ ++#define PCIE_MCAPR_MULTI_MSG_ENABLE_S 20 ++#define PCIE_MCAPR_ADDR64_CAP 0X00800000 /* 64-bit Address Capable */ ++ ++/* MSI Message Address Register */ ++#define PCIE_MA(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x54) ++ ++#define PCIE_MA_ADDR_MASK 0xFFFFFFFC /* Message Address */ ++ ++/* MSI Message Upper Address Register */ ++#define PCIE_MUA(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x58) ++ ++/* MSI Message Data Register */ ++#define PCIE_MD(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x5C) ++ ++#define PCIE_MD_DATA 0x0000FFFF /* Message Data */ ++#define PCIE_MD_DATA_S 0 ++ ++/* PCI Express Capability Register */ ++#define PCIE_XCAP(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x70) ++ ++#define PCIE_XCAP_ID 0x000000FF /* PCI Express Capability ID */ ++#define PCIE_XCAP_ID_S 0 ++#define PCIE_XCAP_NEXT_CAP 0x0000FF00 /* Next Capability Pointer */ ++#define PCIE_XCAP_NEXT_CAP_S 8 ++#define PCIE_XCAP_VER 0x000F0000 /* PCI Express Capability Version */ ++#define PCIE_XCAP_VER_S 16 ++#define PCIE_XCAP_DEV_PORT_TYPE 0x00F00000 /* Device Port Type */ ++#define PCIE_XCAP_DEV_PORT_TYPE_S 20 ++#define PCIE_XCAP_SLOT_IMPLEMENTED 0x01000000 /* Slot Implemented */ ++#define PCIE_XCAP_MSG_INT_NUM 0x3E000000 /* Interrupt Message Number */ ++#define PCIE_XCAP_MSG_INT_NUM_S 25 ++ ++/* Device Capability Register */ ++#define PCIE_DCAP(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x74) ++ ++#define PCIE_DCAP_MAX_PAYLOAD_SIZE 0x00000007 /* Max Payload size */ ++#define PCIE_DCAP_MAX_PAYLOAD_SIZE_S 0 ++#define PCIE_DCAP_PHANTOM_FUNC 0x00000018 /* Phanton Function, not supported */ ++#define PCIE_DCAP_PHANTOM_FUNC_S 3 ++#define PCIE_DCAP_EXT_TAG 0x00000020 /* Extended Tag Field */ ++#define PCIE_DCAP_EP_L0S_LATENCY 0x000001C0 /* EP L0s latency only */ ++#define PCIE_DCAP_EP_L0S_LATENCY_S 6 ++#define PCIE_DCAP_EP_L1_LATENCY 0x00000E00 /* EP L1 latency only */ ++#define PCIE_DCAP_EP_L1_LATENCY_S 9 ++#define PCIE_DCAP_ROLE_BASE_ERR_REPORT 0x00008000 /* Role Based ERR */ ++ ++/* Maximum payload size supported */ ++enum { ++ PCIE_MAX_PAYLOAD_128 = 0, ++ PCIE_MAX_PAYLOAD_256, ++ PCIE_MAX_PAYLOAD_512, ++ PCIE_MAX_PAYLOAD_1024, ++ PCIE_MAX_PAYLOAD_2048, ++ PCIE_MAX_PAYLOAD_4096, ++}; ++ ++/* Device Control and Status Register */ ++#define PCIE_DCTLSTS(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x78) ++ ++#define PCIE_DCTLSTS_CORRECTABLE_ERR_EN 0x00000001 /* COR-ERR */ ++#define PCIE_DCTLSTS_NONFATAL_ERR_EN 0x00000002 /* Non-fatal ERR */ ++#define PCIE_DCTLSTS_FATAL_ERR_EN 0x00000004 /* Fatal ERR */ ++#define PCIE_DCTLSYS_UR_REQ_EN 0x00000008 /* UR ERR */ ++#define PCIE_DCTLSTS_RELAXED_ORDERING_EN 0x00000010 /* Enable relaxing ordering */ ++#define PCIE_DCTLSTS_MAX_PAYLOAD_SIZE 0x000000E0 /* Max payload mask */ ++#define PCIE_DCTLSTS_MAX_PAYLOAD_SIZE_S 5 ++#define PCIE_DCTLSTS_EXT_TAG_EN 0x00000100 /* Extended tag field */ ++#define PCIE_DCTLSTS_PHANTOM_FUNC_EN 0x00000200 /* Phantom Function Enable */ ++#define PCIE_DCTLSTS_AUX_PM_EN 0x00000400 /* AUX Power PM Enable */ ++#define PCIE_DCTLSTS_NO_SNOOP_EN 0x00000800 /* Enable no snoop, except root port*/ ++#define PCIE_DCTLSTS_MAX_READ_SIZE 0x00007000 /* Max Read Request size*/ ++#define PCIE_DCTLSTS_MAX_READ_SIZE_S 12 ++#define PCIE_DCTLSTS_CORRECTABLE_ERR 0x00010000 /* COR-ERR Detected */ ++#define PCIE_DCTLSTS_NONFATAL_ERR 0x00020000 /* Non-Fatal ERR Detected */ ++#define PCIE_DCTLSTS_FATAL_ER 0x00040000 /* Fatal ERR Detected */ ++#define PCIE_DCTLSTS_UNSUPPORTED_REQ 0x00080000 /* UR Detected */ ++#define PCIE_DCTLSTS_AUX_POWER 0x00100000 /* Aux Power Detected */ ++#define PCIE_DCTLSTS_TRANSACT_PENDING 0x00200000 /* Transaction pending */ ++ ++#define PCIE_DCTLSTS_ERR_EN (PCIE_DCTLSTS_CORRECTABLE_ERR_EN | \ ++ PCIE_DCTLSTS_NONFATAL_ERR_EN | PCIE_DCTLSTS_FATAL_ERR_EN | \ ++ PCIE_DCTLSYS_UR_REQ_EN) ++ ++/* Link Capability Register */ ++#define PCIE_LCAP(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x7C) ++#define PCIE_LCAP_MAX_LINK_SPEED 0x0000000F /* Max link speed, 0x1 by default */ ++#define PCIE_LCAP_MAX_LINK_SPEED_S 0 ++#define PCIE_LCAP_MAX_LENGTH_WIDTH 0x000003F0 /* Maxium Length Width */ ++#define PCIE_LCAP_MAX_LENGTH_WIDTH_S 4 ++#define PCIE_LCAP_ASPM_LEVEL 0x00000C00 /* Active State Link PM Support */ ++#define PCIE_LCAP_ASPM_LEVEL_S 10 ++#define PCIE_LCAP_L0S_EIXT_LATENCY 0x00007000 /* L0s Exit Latency */ ++#define PCIE_LCAP_L0S_EIXT_LATENCY_S 12 ++#define PCIE_LCAP_L1_EXIT_LATENCY 0x00038000 /* L1 Exit Latency */ ++#define PCIE_LCAP_L1_EXIT_LATENCY_S 15 ++#define PCIE_LCAP_CLK_PM 0x00040000 /* Clock Power Management */ ++#define PCIE_LCAP_SDER 0x00080000 /* Surprise Down Error Reporting */ ++#define PCIE_LCAP_DLL_ACTIVE_REPROT 0x00100000 /* Data Link Layer Active Reporting Capable */ ++#define PCIE_LCAP_PORT_NUM 0xFF0000000 /* Port number */ ++#define PCIE_LCAP_PORT_NUM_S 24 ++ ++/* Maximum Length width definition */ ++#define PCIE_MAX_LENGTH_WIDTH_RES 0x00 ++#define PCIE_MAX_LENGTH_WIDTH_X1 0x01 /* Default */ ++#define PCIE_MAX_LENGTH_WIDTH_X2 0x02 ++#define PCIE_MAX_LENGTH_WIDTH_X4 0x04 ++#define PCIE_MAX_LENGTH_WIDTH_X8 0x08 ++#define PCIE_MAX_LENGTH_WIDTH_X12 0x0C ++#define PCIE_MAX_LENGTH_WIDTH_X16 0x10 ++#define PCIE_MAX_LENGTH_WIDTH_X32 0x20 ++ ++/* Active State Link PM definition */ ++enum { ++ PCIE_ASPM_RES0 = 0, ++ PCIE_ASPM_L0S_ENTRY_SUPPORT, /* L0s */ ++ PCIE_ASPM_RES1, ++ PCIE_ASPM_L0S_L1_ENTRY_SUPPORT, /* L0s and L1, default */ ++}; ++ ++/* L0s Exit Latency definition */ ++enum { ++ PCIE_L0S_EIXT_LATENCY_L64NS = 0, /* < 64 ns */ ++ PCIE_L0S_EIXT_LATENCY_B64A128, /* > 64 ns < 128 ns */ ++ PCIE_L0S_EIXT_LATENCY_B128A256, /* > 128 ns < 256 ns */ ++ PCIE_L0S_EIXT_LATENCY_B256A512, /* > 256 ns < 512 ns */ ++ PCIE_L0S_EIXT_LATENCY_B512TO1U, /* > 512 ns < 1 us */ ++ PCIE_L0S_EIXT_LATENCY_B1A2U, /* > 1 us < 2 us */ ++ PCIE_L0S_EIXT_LATENCY_B2A4U, /* > 2 us < 4 us */ ++ PCIE_L0S_EIXT_LATENCY_M4US, /* > 4 us */ ++}; ++ ++/* L1 Exit Latency definition */ ++enum { ++ PCIE_L1_EXIT_LATENCY_L1US = 0, /* < 1 us */ ++ PCIE_L1_EXIT_LATENCY_B1A2, /* > 1 us < 2 us */ ++ PCIE_L1_EXIT_LATENCY_B2A4, /* > 2 us < 4 us */ ++ PCIE_L1_EXIT_LATENCY_B4A8, /* > 4 us < 8 us */ ++ PCIE_L1_EXIT_LATENCY_B8A16, /* > 8 us < 16 us */ ++ PCIE_L1_EXIT_LATENCY_B16A32, /* > 16 us < 32 us */ ++ PCIE_L1_EXIT_LATENCY_B32A64, /* > 32 us < 64 us */ ++ PCIE_L1_EXIT_LATENCY_M64US, /* > 64 us */ ++}; ++ ++/* Link Control and Status Register */ ++#define PCIE_LCTLSTS(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x80) ++#define PCIE_LCTLSTS_ASPM_ENABLE 0x00000003 /* Active State Link PM Control */ ++#define PCIE_LCTLSTS_ASPM_ENABLE_S 0 ++#define PCIE_LCTLSTS_RCB128 0x00000008 /* Read Completion Boundary 128*/ ++#define PCIE_LCTLSTS_LINK_DISABLE 0x00000010 /* Link Disable */ ++#define PCIE_LCTLSTS_RETRIAN_LINK 0x00000020 /* Retrain Link */ ++#define PCIE_LCTLSTS_COM_CLK_CFG 0x00000040 /* Common Clock Configuration */ ++#define PCIE_LCTLSTS_EXT_SYNC 0x00000080 /* Extended Synch */ ++#define PCIE_LCTLSTS_CLK_PM_EN 0x00000100 /* Enable Clock Powerm Management */ ++#define PCIE_LCTLSTS_LINK_SPEED 0x000F0000 /* Link Speed */ ++#define PCIE_LCTLSTS_LINK_SPEED_S 16 ++#define PCIE_LCTLSTS_NEGOTIATED_LINK_WIDTH 0x03F00000 /* Negotiated Link Width */ ++#define PCIE_LCTLSTS_NEGOTIATED_LINK_WIDTH_S 20 ++#define PCIE_LCTLSTS_RETRAIN_PENDING 0x08000000 /* Link training is ongoing */ ++#define PCIE_LCTLSTS_SLOT_CLK_CFG 0x10000000 /* Slot Clock Configuration */ ++#define PCIE_LCTLSTS_DLL_ACTIVE 0x20000000 /* Data Link Layer Active */ ++ ++/* Slot Capabilities Register */ ++#define PCIE_SLCAP(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x84) ++ ++/* Slot Capabilities */ ++#define PCIE_SLCTLSTS(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x88) ++ ++/* Root Control and Capability Register */ ++#define PCIE_RCTLCAP(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x8C) ++#define PCIE_RCTLCAP_SERR_ON_CORRECTABLE_ERR 0x00000001 /* #SERR on COR-ERR */ ++#define PCIE_RCTLCAP_SERR_ON_NONFATAL_ERR 0x00000002 /* #SERR on Non-Fatal ERR */ ++#define PCIE_RCTLCAP_SERR_ON_FATAL_ERR 0x00000004 /* #SERR on Fatal ERR */ ++#define PCIE_RCTLCAP_PME_INT_EN 0x00000008 /* PME Interrupt Enable */ ++#define PCIE_RCTLCAP_SERR_ENABLE (PCIE_RCTLCAP_SERR_ON_CORRECTABLE_ERR | \ ++ PCIE_RCTLCAP_SERR_ON_NONFATAL_ERR | PCIE_RCTLCAP_SERR_ON_FATAL_ERR) ++/* Root Status Register */ ++#define PCIE_RSTS(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x90) ++#define PCIE_RSTS_PME_REQ_ID 0x0000FFFF /* PME Request ID */ ++#define PCIE_RSTS_PME_REQ_ID_S 0 ++#define PCIE_RSTS_PME_STATUS 0x00010000 /* PME Status */ ++#define PCIE_RSTS_PME_PENDING 0x00020000 /* PME Pending */ ++ ++/* PCI Express Enhanced Capability Header */ ++#define PCIE_ENHANCED_CAP(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x100) ++#define PCIE_ENHANCED_CAP_ID 0x0000FFFF /* PCI Express Extended Capability ID */ ++#define PCIE_ENHANCED_CAP_ID_S 0 ++#define PCIE_ENHANCED_CAP_VER 0x000F0000 /* Capability Version */ ++#define PCIE_ENHANCED_CAP_VER_S 16 ++#define PCIE_ENHANCED_CAP_NEXT_OFFSET 0xFFF00000 /* Next Capability Offset */ ++#define PCIE_ENHANCED_CAP_NEXT_OFFSET_S 20 ++ ++/* Uncorrectable Error Status Register */ ++#define PCIE_UES_R(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x104) ++#define PCIE_DATA_LINK_PROTOCOL_ERR 0x00000010 /* Data Link Protocol Error Status */ ++#define PCIE_SURPRISE_DOWN_ERROR 0x00000020 /* Surprise Down Error Status */ ++#define PCIE_POISONED_TLP 0x00001000 /* Poisoned TLP Status */ ++#define PCIE_FC_PROTOCOL_ERR 0x00002000 /* Flow Control Protocol Error Status */ ++#define PCIE_COMPLETION_TIMEOUT 0x00004000 /* Completion Timeout Status */ ++#define PCIE_COMPLETOR_ABORT 0x00008000 /* Completer Abort Error */ ++#define PCIE_UNEXPECTED_COMPLETION 0x00010000 /* Unexpected Completion Status */ ++#define PCIE_RECEIVER_OVERFLOW 0x00020000 /* Receive Overflow Status */ ++#define PCIE_MALFORNED_TLP 0x00040000 /* Malformed TLP Stauts */ ++#define PCIE_ECRC_ERR 0x00080000 /* ECRC Error Stauts */ ++#define PCIE_UR_REQ 0x00100000 /* Unsupported Request Error Status */ ++#define PCIE_ALL_UNCORRECTABLE_ERR (PCIE_DATA_LINK_PROTOCOL_ERR | PCIE_SURPRISE_DOWN_ERROR | \ ++ PCIE_POISONED_TLP | PCIE_FC_PROTOCOL_ERR | PCIE_COMPLETION_TIMEOUT | \ ++ PCIE_COMPLETOR_ABORT | PCIE_UNEXPECTED_COMPLETION | PCIE_RECEIVER_OVERFLOW |\ ++ PCIE_MALFORNED_TLP | PCIE_ECRC_ERR | PCIE_UR_REQ) ++ ++/* Uncorrectable Error Mask Register, Mask means no report */ ++#define PCIE_UEMR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x108) ++ ++/* Uncorrectable Error Severity Register */ ++#define PCIE_UESR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x10C) ++ ++/* Correctable Error Status Register */ ++#define PCIE_CESR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x110) ++#define PCIE_RX_ERR 0x00000001 /* Receive Error Status */ ++#define PCIE_BAD_TLP 0x00000040 /* Bad TLP Status */ ++#define PCIE_BAD_DLLP 0x00000080 /* Bad DLLP Status */ ++#define PCIE_REPLAY_NUM_ROLLOVER 0x00000100 /* Replay Number Rollover Status */ ++#define PCIE_REPLAY_TIMER_TIMEOUT_ERR 0x00001000 /* Reply Timer Timeout Status */ ++#define PCIE_ADVISORY_NONFTAL_ERR 0x00002000 /* Advisory Non-Fatal Error Status */ ++#define PCIE_CORRECTABLE_ERR (PCIE_RX_ERR | PCIE_BAD_TLP | PCIE_BAD_DLLP | PCIE_REPLAY_NUM_ROLLOVER |\ ++ PCIE_REPLAY_TIMER_TIMEOUT_ERR | PCIE_ADVISORY_NONFTAL_ERR) ++ ++/* Correctable Error Mask Register */ ++#define PCIE_CEMR(X) (volatile u32*)(PCIE_RC_CFG_BASE + 0x114) ++ ++/* Advanced Error Capabilities and Control Register */ ++#define PCIE_AECCR(X) (volatile u32*)(PCIE_RC_CFG_BASE + 0x118) ++#define PCIE_AECCR_FIRST_ERR_PTR 0x0000001F /* First Error Pointer */ ++#define PCIE_AECCR_FIRST_ERR_PTR_S 0 ++#define PCIE_AECCR_ECRC_GEN_CAP 0x00000020 /* ECRC Generation Capable */ ++#define PCIE_AECCR_ECRC_GEN_EN 0x00000040 /* ECRC Generation Enable */ ++#define PCIE_AECCR_ECRC_CHECK_CAP 0x00000080 /* ECRC Check Capable */ ++#define PCIE_AECCR_ECRC_CHECK_EN 0x00000100 /* ECRC Check Enable */ ++ ++/* Header Log Register 1 */ ++#define PCIE_HLR1(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x11C) ++ ++/* Header Log Register 2 */ ++#define PCIE_HLR2(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x120) ++ ++/* Header Log Register 3 */ ++#define PCIE_HLR3(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x124) ++ ++/* Header Log Register 4 */ ++#define PCIE_HLR4(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x128) ++ ++/* Root Error Command Register */ ++#define PCIE_RECR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x12C) ++#define PCIE_RECR_CORRECTABLE_ERR_REPORT_EN 0x00000001 /* COR-ERR */ ++#define PCIE_RECR_NONFATAL_ERR_REPORT_EN 0x00000002 /* Non-Fatal ERR */ ++#define PCIE_RECR_FATAL_ERR_REPORT_EN 0x00000004 /* Fatal ERR */ ++#define PCIE_RECR_ERR_REPORT_EN (PCIE_RECR_CORRECTABLE_ERR_REPORT_EN | \ ++ PCIE_RECR_NONFATAL_ERR_REPORT_EN | PCIE_RECR_FATAL_ERR_REPORT_EN) ++ ++/* Root Error Status Register */ ++#define PCIE_RESR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x130) ++#define PCIE_RESR_CORRECTABLE_ERR 0x00000001 /* COR-ERR Receveid */ ++#define PCIE_RESR_MULTI_CORRECTABLE_ERR 0x00000002 /* Multiple COR-ERR Received */ ++#define PCIE_RESR_FATAL_NOFATAL_ERR 0x00000004 /* ERR Fatal/Non-Fatal Received */ ++#define PCIE_RESR_MULTI_FATAL_NOFATAL_ERR 0x00000008 /* Multiple ERR Fatal/Non-Fatal Received */ ++#define PCIE_RESR_FIRST_UNCORRECTABLE_FATAL_ERR 0x00000010 /* First UN-COR Fatal */ ++#define PCIR_RESR_NON_FATAL_ERR 0x00000020 /* Non-Fatal Error Message Received */ ++#define PCIE_RESR_FATAL_ERR 0x00000040 /* Fatal Message Received */ ++#define PCIE_RESR_AER_INT_MSG_NUM 0xF8000000 /* Advanced Error Interrupt Message Number */ ++#define PCIE_RESR_AER_INT_MSG_NUM_S 27 ++ ++/* Error Source Indentification Register */ ++#define PCIE_ESIR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x134) ++#define PCIE_ESIR_CORRECTABLE_ERR_SRC_ID 0x0000FFFF ++#define PCIE_ESIR_CORRECTABLE_ERR_SRC_ID_S 0 ++#define PCIE_ESIR_FATAL_NON_FATAL_SRC_ID 0xFFFF0000 ++#define PCIE_ESIR_FATAL_NON_FATAL_SRC_ID_S 16 ++ ++/* VC Enhanced Capability Header */ ++#define PCIE_VC_ECH(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x140) ++ ++/* Port VC Capability Register */ ++#define PCIE_PVC1(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x144) ++#define PCIE_PVC1_EXT_VC_CNT 0x00000007 /* Extended VC Count */ ++#define PCIE_PVC1_EXT_VC_CNT_S 0 ++#define PCIE_PVC1_LOW_PRI_EXT_VC_CNT 0x00000070 /* Low Priority Extended VC Count */ ++#define PCIE_PVC1_LOW_PRI_EXT_VC_CNT_S 4 ++#define PCIE_PVC1_REF_CLK 0x00000300 /* Reference Clock */ ++#define PCIE_PVC1_REF_CLK_S 8 ++#define PCIE_PVC1_PORT_ARB_TAB_ENTRY_SIZE 0x00000C00 /* Port Arbitration Table Entry Size */ ++#define PCIE_PVC1_PORT_ARB_TAB_ENTRY_SIZE_S 10 ++ ++/* Extended Virtual Channel Count Defintion */ ++#define PCIE_EXT_VC_CNT_MIN 0 ++#define PCIE_EXT_VC_CNT_MAX 7 ++ ++/* Port Arbitration Table Entry Size Definition */ ++enum { ++ PCIE_PORT_ARB_TAB_ENTRY_SIZE_S1BIT = 0, ++ PCIE_PORT_ARB_TAB_ENTRY_SIZE_S2BIT, ++ PCIE_PORT_ARB_TAB_ENTRY_SIZE_S4BIT, ++ PCIE_PORT_ARB_TAB_ENTRY_SIZE_S8BIT, ++}; ++ ++/* Port VC Capability Register 2 */ ++#define PCIE_PVC2(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x148) ++#define PCIE_PVC2_VC_ARB_16P_FIXED_WRR 0x00000001 /* HW Fixed arbitration, 16 phase WRR */ ++#define PCIE_PVC2_VC_ARB_32P_WRR 0x00000002 /* 32 phase WRR */ ++#define PCIE_PVC2_VC_ARB_64P_WRR 0x00000004 /* 64 phase WRR */ ++#define PCIE_PVC2_VC_ARB_128P_WRR 0x00000008 /* 128 phase WRR */ ++#define PCIE_PVC2_VC_ARB_WRR 0x0000000F ++#define PCIE_PVC2_VC_ARB_TAB_OFFSET 0xFF000000 /* VC arbitration table offset, not support */ ++#define PCIE_PVC2_VC_ARB_TAB_OFFSET_S 24 ++ ++/* Port VC Control and Status Register */ ++#define PCIE_PVCCRSR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x14C) ++#define PCIE_PVCCRSR_LOAD_VC_ARB_TAB 0x00000001 /* Load VC Arbitration Table */ ++#define PCIE_PVCCRSR_VC_ARB_SEL 0x0000000E /* VC Arbitration Select */ ++#define PCIE_PVCCRSR_VC_ARB_SEL_S 1 ++#define PCIE_PVCCRSR_VC_ARB_TAB_STATUS 0x00010000 /* Arbitration Status */ ++ ++/* VC0 Resource Capability Register */ ++#define PCIE_VC0_RC(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x150) ++#define PCIE_VC0_RC_PORT_ARB_HW_FIXED 0x00000001 /* HW Fixed arbitration */ ++#define PCIE_VC0_RC_PORT_ARB_32P_WRR 0x00000002 /* 32 phase WRR */ ++#define PCIE_VC0_RC_PORT_ARB_64P_WRR 0x00000004 /* 64 phase WRR */ ++#define PCIE_VC0_RC_PORT_ARB_128P_WRR 0x00000008 /* 128 phase WRR */ ++#define PCIE_VC0_RC_PORT_ARB_TM_128P_WRR 0x00000010 /* Time-based 128 phase WRR */ ++#define PCIE_VC0_RC_PORT_ARB_TM_256P_WRR 0x00000020 /* Time-based 256 phase WRR */ ++#define PCIE_VC0_RC_PORT_ARB (PCIE_VC0_RC_PORT_ARB_HW_FIXED | PCIE_VC0_RC_PORT_ARB_32P_WRR |\ ++ PCIE_VC0_RC_PORT_ARB_64P_WRR | PCIE_VC0_RC_PORT_ARB_128P_WRR | \ ++ PCIE_VC0_RC_PORT_ARB_TM_128P_WRR | PCIE_VC0_RC_PORT_ARB_TM_256P_WRR) ++ ++#define PCIE_VC0_RC_REJECT_SNOOP 0x00008000 /* Reject Snoop Transactioin */ ++#define PCIE_VC0_RC_MAX_TIMESLOTS 0x007F0000 /* Maximum time Slots */ ++#define PCIE_VC0_RC_MAX_TIMESLOTS_S 16 ++#define PCIE_VC0_RC_PORT_ARB_TAB_OFFSET 0xFF000000 /* Port Arbitration Table Offset */ ++#define PCIE_VC0_RC_PORT_ARB_TAB_OFFSET_S 24 ++ ++/* VC0 Resource Control Register */ ++#define PCIE_VC0_RC0(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x154) ++#define PCIE_VC0_RC0_TVM0 0x00000001 /* TC0 and VC0 */ ++#define PCIE_VC0_RC0_TVM1 0x00000002 /* TC1 and VC1 */ ++#define PCIE_VC0_RC0_TVM2 0x00000004 /* TC2 and VC2 */ ++#define PCIE_VC0_RC0_TVM3 0x00000008 /* TC3 and VC3 */ ++#define PCIE_VC0_RC0_TVM4 0x00000010 /* TC4 and VC4 */ ++#define PCIE_VC0_RC0_TVM5 0x00000020 /* TC5 and VC5 */ ++#define PCIE_VC0_RC0_TVM6 0x00000040 /* TC6 and VC6 */ ++#define PCIE_VC0_RC0_TVM7 0x00000080 /* TC7 and VC7 */ ++#define PCIE_VC0_RC0_TC_VC 0x000000FF /* TC/VC mask */ ++ ++#define PCIE_VC0_RC0_LOAD_PORT_ARB_TAB 0x00010000 /* Load Port Arbitration Table */ ++#define PCIE_VC0_RC0_PORT_ARB_SEL 0x000E0000 /* Port Arbitration Select */ ++#define PCIE_VC0_RC0_PORT_ARB_SEL_S 17 ++#define PCIE_VC0_RC0_VC_ID 0x07000000 /* VC ID */ ++#define PCIE_VC0_RC0_VC_ID_S 24 ++#define PCIE_VC0_RC0_VC_EN 0x80000000 /* VC Enable */ ++ ++/* VC0 Resource Status Register */ ++#define PCIE_VC0_RSR0(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x158) ++#define PCIE_VC0_RSR0_PORT_ARB_TAB_STATUS 0x00010000 /* Port Arbitration Table Status,not used */ ++#define PCIE_VC0_RSR0_VC_NEG_PENDING 0x00020000 /* VC Negotiation Pending */ ++ ++/* Ack Latency Timer and Replay Timer Register */ ++#define PCIE_ALTRT(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x700) ++#define PCIE_ALTRT_ROUND_TRIP_LATENCY_LIMIT 0x0000FFFF /* Round Trip Latency Time Limit */ ++#define PCIE_ALTRT_ROUND_TRIP_LATENCY_LIMIT_S 0 ++#define PCIE_ALTRT_REPLAY_TIME_LIMIT 0xFFFF0000 /* Replay Time Limit */ ++#define PCIE_ALTRT_REPLAY_TIME_LIMIT_S 16 ++ ++/* Other Message Register */ ++#define PCIE_OMR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x704) ++ ++/* Port Force Link Register */ ++#define PCIE_PFLR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x708) ++#define PCIE_PFLR_LINK_NUM 0x000000FF /* Link Number */ ++#define PCIE_PFLR_LINK_NUM_S 0 ++#define PCIE_PFLR_FORCE_LINK 0x00008000 /* Force link */ ++#define PCIE_PFLR_LINK_STATE 0x003F0000 /* Link State */ ++#define PCIE_PFLR_LINK_STATE_S 16 ++#define PCIE_PFLR_LOW_POWER_ENTRY_CNT 0xFF000000 /* Low Power Entrance Count, only for EP */ ++#define PCIE_PFLR_LOW_POWER_ENTRY_CNT_S 24 ++ ++/* Ack Frequency Register */ ++#define PCIE_AFR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x70C) ++#define PCIE_AFR_AF 0x000000FF /* Ack Frequency */ ++#define PCIE_AFR_AF_S 0 ++#define PCIE_AFR_FTS_NUM 0x0000FF00 /* The number of Fast Training Sequence from L0S to L0 */ ++#define PCIE_AFR_FTS_NUM_S 8 ++#define PCIE_AFR_COM_FTS_NUM 0x00FF0000 /* N_FTS; when common clock is used*/ ++#define PCIE_AFR_COM_FTS_NUM_S 16 ++#define PCIE_AFR_L0S_ENTRY_LATENCY 0x07000000 /* L0s Entrance Latency */ ++#define PCIE_AFR_L0S_ENTRY_LATENCY_S 24 ++#define PCIE_AFR_L1_ENTRY_LATENCY 0x38000000 /* L1 Entrance Latency */ ++#define PCIE_AFR_L1_ENTRY_LATENCY_S 27 ++#define PCIE_AFR_FTS_NUM_DEFAULT 32 ++#define PCIE_AFR_L0S_ENTRY_LATENCY_DEFAULT 7 ++#define PCIE_AFR_L1_ENTRY_LATENCY_DEFAULT 5 ++ ++/* Port Link Control Register */ ++#define PCIE_PLCR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x710) ++#define PCIE_PLCR_OTHER_MSG_REQ 0x00000001 /* Other Message Request */ ++#define PCIE_PLCR_SCRAMBLE_DISABLE 0x00000002 /* Scramble Disable */ ++#define PCIE_PLCR_LOOPBACK_EN 0x00000004 /* Loopback Enable */ ++#define PCIE_PLCR_LTSSM_HOT_RST 0x00000008 /* Force LTSSM to the hot reset */ ++#define PCIE_PLCR_DLL_LINK_EN 0x00000020 /* Enable Link initialization */ ++#define PCIE_PLCR_FAST_LINK_SIM_EN 0x00000080 /* Sets all internal timers to fast mode for simulation purposes */ ++#define PCIE_PLCR_LINK_MODE 0x003F0000 /* Link Mode Enable Mask */ ++#define PCIE_PLCR_LINK_MODE_S 16 ++#define PCIE_PLCR_CORRUPTED_CRC_EN 0x02000000 /* Enabled Corrupt CRC */ ++ ++/* Lane Skew Register */ ++#define PCIE_LSR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x714) ++#define PCIE_LSR_LANE_SKEW_NUM 0x00FFFFFF /* Insert Lane Skew for Transmit, not applicable */ ++#define PCIE_LSR_LANE_SKEW_NUM_S 0 ++#define PCIE_LSR_FC_DISABLE 0x01000000 /* Disable of Flow Control */ ++#define PCIE_LSR_ACKNAK_DISABLE 0x02000000 /* Disable of Ack/Nak */ ++#define PCIE_LSR_LANE_DESKEW_DISABLE 0x80000000 /* Disable of Lane-to-Lane Skew */ ++ ++/* Symbol Number Register */ ++#define PCIE_SNR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x718) ++#define PCIE_SNR_TS 0x0000000F /* Number of TS Symbol */ ++#define PCIE_SNR_TS_S 0 ++#define PCIE_SNR_SKP 0x00000700 /* Number of SKP Symbol */ ++#define PCIE_SNR_SKP_S 8 ++#define PCIE_SNR_REPLAY_TIMER 0x0007C000 /* Timer Modifier for Replay Timer */ ++#define PCIE_SNR_REPLAY_TIMER_S 14 ++#define PCIE_SNR_ACKNAK_LATENCY_TIMER 0x00F80000 /* Timer Modifier for Ack/Nak Latency Timer */ ++#define PCIE_SNR_ACKNAK_LATENCY_TIMER_S 19 ++#define PCIE_SNR_FC_TIMER 0x1F000000 /* Timer Modifier for Flow Control Watchdog Timer */ ++#define PCIE_SNR_FC_TIMER_S 28 ++ ++/* Symbol Timer Register and Filter Mask Register 1 */ ++#define PCIE_STRFMR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x71C) ++#define PCIE_STRFMR_SKP_INTERVAL 0x000007FF /* SKP lnterval Value */ ++#define PCIE_STRFMR_SKP_INTERVAL_S 0 ++#define PCIE_STRFMR_FC_WDT_DISABLE 0x00008000 /* Disable of FC Watchdog Timer */ ++#define PCIE_STRFMR_TLP_FUNC_MISMATCH_OK 0x00010000 /* Mask Function Mismatch Filtering for Incoming Requests */ ++#define PCIE_STRFMR_POISONED_TLP_OK 0x00020000 /* Mask Poisoned TLP Filtering */ ++#define PCIE_STRFMR_BAR_MATCH_OK 0x00040000 /* Mask BAR Match Filtering */ ++#define PCIE_STRFMR_TYPE1_CFG_REQ_OK 0x00080000 /* Mask Type 1 Configuration Request Filtering */ ++#define PCIE_STRFMR_LOCKED_REQ_OK 0x00100000 /* Mask Locked Request Filtering */ ++#define PCIE_STRFMR_CPL_TAG_ERR_RULES_OK 0x00200000 /* Mask Tag Error Rules for Received Completions */ ++#define PCIE_STRFMR_CPL_REQUESTOR_ID_MISMATCH_OK 0x00400000 /* Mask Requester ID Mismatch Error for Received Completions */ ++#define PCIE_STRFMR_CPL_FUNC_MISMATCH_OK 0x00800000 /* Mask Function Mismatch Error for Received Completions */ ++#define PCIE_STRFMR_CPL_TC_MISMATCH_OK 0x01000000 /* Mask Traffic Class Mismatch Error for Received Completions */ ++#define PCIE_STRFMR_CPL_ATTR_MISMATCH_OK 0x02000000 /* Mask Attribute Mismatch Error for Received Completions */ ++#define PCIE_STRFMR_CPL_LENGTH_MISMATCH_OK 0x04000000 /* Mask Length Mismatch Error for Received Completions */ ++#define PCIE_STRFMR_TLP_ECRC_ERR_OK 0x08000000 /* Mask ECRC Error Filtering */ ++#define PCIE_STRFMR_CPL_TLP_ECRC_OK 0x10000000 /* Mask ECRC Error Filtering for Completions */ ++#define PCIE_STRFMR_RX_TLP_MSG_NO_DROP 0x20000000 /* Send Message TLPs */ ++#define PCIE_STRFMR_RX_IO_TRANS_ENABLE 0x40000000 /* Mask Filtering of received I/O Requests */ ++#define PCIE_STRFMR_RX_CFG_TRANS_ENABLE 0x80000000 /* Mask Filtering of Received Configuration Requests */ ++ ++#define PCIE_DEF_SKP_INTERVAL 700 /* 1180 ~1538 , 125MHz * 2, 250MHz * 1 */ ++ ++/* Filter Masker Register 2 */ ++#define PCIE_FMR2(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x720) ++#define PCIE_FMR2_VENDOR_MSG0_PASSED_TO_TRGT1 0x00000001 /* Mask RADM Filtering and Error Handling Rules */ ++#define PCIE_FMR2_VENDOR_MSG1_PASSED_TO_TRGT1 0x00000002 /* Mask RADM Filtering and Error Handling Rules */ ++ ++/* Debug Register 0 */ ++#define PCIE_DBR0(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x728) ++ ++/* Debug Register 1 */ ++#define PCIE_DBR1(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x72C) ++ ++/* Transmit Posted FC Credit Status Register */ ++#define PCIE_TPFCS(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x730) ++#define PCIE_TPFCS_TX_P_DATA_FC_CREDITS 0x00000FFF /* Transmit Posted Data FC Credits */ ++#define PCIE_TPFCS_TX_P_DATA_FC_CREDITS_S 0 ++#define PCIE_TPFCS_TX_P_HDR_FC_CREDITS 0x000FF000 /* Transmit Posted Header FC Credits */ ++#define PCIE_TPFCS_TX_P_HDR_FC_CREDITS_S 12 ++ ++/* Transmit Non-Posted FC Credit Status */ ++#define PCIE_TNPFCS(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x734) ++#define PCIE_TNPFCS_TX_NP_DATA_FC_CREDITS 0x00000FFF /* Transmit Non-Posted Data FC Credits */ ++#define PCIE_TNPFCS_TX_NP_DATA_FC_CREDITS_S 0 ++#define PCIE_TNPFCS_TX_NP_HDR_FC_CREDITS 0x000FF000 /* Transmit Non-Posted Header FC Credits */ ++#define PCIE_TNPFCS_TX_NP_HDR_FC_CREDITS_S 12 ++ ++/* Transmit Complete FC Credit Status Register */ ++#define PCIE_TCFCS(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x738) ++#define PCIE_TCFCS_TX_CPL_DATA_FC_CREDITS 0x00000FFF /* Transmit Completion Data FC Credits */ ++#define PCIE_TCFCS_TX_CPL_DATA_FC_CREDITS_S 0 ++#define PCIE_TCFCS_TX_CPL_HDR_FC_CREDITS 0x000FF000 /* Transmit Completion Header FC Credits */ ++#define PCIE_TCFCS_TX_CPL_HDR_FC_CREDITS_S 12 ++ ++/* Queue Status Register */ ++#define PCIE_QSR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x73C) ++#define PCIE_QSR_WAIT_UPDATE_FC_DLL 0x00000001 /* Received TLP FC Credits Not Returned */ ++#define PCIE_QSR_TX_RETRY_BUF_NOT_EMPTY 0x00000002 /* Transmit Retry Buffer Not Empty */ ++#define PCIE_QSR_RX_QUEUE_NOT_EMPTY 0x00000004 /* Received Queue Not Empty */ ++ ++/* VC Transmit Arbitration Register 1 */ ++#define PCIE_VCTAR1(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x740) ++#define PCIE_VCTAR1_WRR_WEIGHT_VC0 0x000000FF /* WRR Weight for VC0 */ ++#define PCIE_VCTAR1_WRR_WEIGHT_VC1 0x0000FF00 /* WRR Weight for VC1 */ ++#define PCIE_VCTAR1_WRR_WEIGHT_VC2 0x00FF0000 /* WRR Weight for VC2 */ ++#define PCIE_VCTAR1_WRR_WEIGHT_VC3 0xFF000000 /* WRR Weight for VC3 */ ++ ++/* VC Transmit Arbitration Register 2 */ ++#define PCIE_VCTAR2(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x744) ++#define PCIE_VCTAR2_WRR_WEIGHT_VC4 0x000000FF /* WRR Weight for VC4 */ ++#define PCIE_VCTAR2_WRR_WEIGHT_VC5 0x0000FF00 /* WRR Weight for VC5 */ ++#define PCIE_VCTAR2_WRR_WEIGHT_VC6 0x00FF0000 /* WRR Weight for VC6 */ ++#define PCIE_VCTAR2_WRR_WEIGHT_VC7 0xFF000000 /* WRR Weight for VC7 */ ++ ++/* VC0 Posted Receive Queue Control Register */ ++#define PCIE_VC0_PRQCR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x748) ++#define PCIE_VC0_PRQCR_P_DATA_CREDITS 0x00000FFF /* VC0 Posted Data Credits */ ++#define PCIE_VC0_PRQCR_P_DATA_CREDITS_S 0 ++#define PCIE_VC0_PRQCR_P_HDR_CREDITS 0x000FF000 /* VC0 Posted Header Credits */ ++#define PCIE_VC0_PRQCR_P_HDR_CREDITS_S 12 ++#define PCIE_VC0_PRQCR_P_TLP_QUEUE_MODE 0x00E00000 /* VC0 Posted TLP Queue Mode */ ++#define PCIE_VC0_PRQCR_P_TLP_QUEUE_MODE_S 20 ++#define PCIE_VC0_PRQCR_TLP_RELAX_ORDER 0x40000000 /* TLP Type Ordering for VC0 */ ++#define PCIE_VC0_PRQCR_VC_STRICT_ORDER 0x80000000 /* VC0 Ordering for Receive Queues */ ++ ++/* VC0 Non-Posted Receive Queue Control */ ++#define PCIE_VC0_NPRQCR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x74C) ++#define PCIE_VC0_NPRQCR_NP_DATA_CREDITS 0x00000FFF /* VC0 Non-Posted Data Credits */ ++#define PCIE_VC0_NPRQCR_NP_DATA_CREDITS_S 0 ++#define PCIE_VC0_NPRQCR_NP_HDR_CREDITS 0x000FF000 /* VC0 Non-Posted Header Credits */ ++#define PCIE_VC0_NPRQCR_NP_HDR_CREDITS_S 12 ++#define PCIE_VC0_NPRQCR_NP_TLP_QUEUE_MODE 0x00E00000 /* VC0 Non-Posted TLP Queue Mode */ ++#define PCIE_VC0_NPRQCR_NP_TLP_QUEUE_MODE_S 20 ++ ++/* VC0 Completion Receive Queue Control */ ++#define PCIE_VC0_CRQCR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x750) ++#define PCIE_VC0_CRQCR_CPL_DATA_CREDITS 0x00000FFF /* VC0 Completion TLP Queue Mode */ ++#define PCIE_VC0_CRQCR_CPL_DATA_CREDITS_S 0 ++#define PCIE_VC0_CRQCR_CPL_HDR_CREDITS 0x000FF000 /* VC0 Completion Header Credits */ ++#define PCIE_VC0_CRQCR_CPL_HDR_CREDITS_S 12 ++#define PCIE_VC0_CRQCR_CPL_TLP_QUEUE_MODE 0x00E00000 /* VC0 Completion Data Credits */ ++#define PCIE_VC0_CRQCR_CPL_TLP_QUEUE_MODE_S 21 ++ ++/* Applicable to the above three registers */ ++enum { ++ PCIE_VC0_TLP_QUEUE_MODE_STORE_FORWARD = 1, ++ PCIE_VC0_TLP_QUEUE_MODE_CUT_THROUGH = 2, ++ PCIE_VC0_TLP_QUEUE_MODE_BYPASS = 4, ++}; ++ ++/* VC0 Posted Buffer Depth Register */ ++#define PCIE_VC0_PBD(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x7A8) ++#define PCIE_VC0_PBD_P_DATA_QUEUE_ENTRIES 0x00003FFF /* VC0 Posted Data Queue Depth */ ++#define PCIE_VC0_PBD_P_DATA_QUEUE_ENTRIES_S 0 ++#define PCIE_VC0_PBD_P_HDR_QUEUE_ENTRIES 0x03FF0000 /* VC0 Posted Header Queue Depth */ ++#define PCIE_VC0_PBD_P_HDR_QUEUE_ENTRIES_S 16 ++ ++/* VC0 Non-Posted Buffer Depth Register */ ++#define PCIE_VC0_NPBD(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x7AC) ++#define PCIE_VC0_NPBD_NP_DATA_QUEUE_ENTRIES 0x00003FFF /* VC0 Non-Posted Data Queue Depth */ ++#define PCIE_VC0_NPBD_NP_DATA_QUEUE_ENTRIES_S 0 ++#define PCIE_VC0_NPBD_NP_HDR_QUEUE_ENTRIES 0x03FF0000 /* VC0 Non-Posted Header Queue Depth */ ++#define PCIE_VC0_NPBD_NP_HDR_QUEUE_ENTRIES_S 16 ++ ++/* VC0 Completion Buffer Depth Register */ ++#define PCIE_VC0_CBD(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x7B0) ++#define PCIE_VC0_CBD_CPL_DATA_QUEUE_ENTRIES 0x00003FFF /* C0 Completion Data Queue Depth */ ++#define PCIE_VC0_CBD_CPL_DATA_QUEUE_ENTRIES_S 0 ++#define PCIE_VC0_CBD_CPL_HDR_QUEUE_ENTRIES 0x03FF0000 /* VC0 Completion Header Queue Depth */ ++#define PCIE_VC0_CBD_CPL_HDR_QUEUE_ENTRIES_S 16 ++ ++/* PHY Status Register, all zeros in VR9 */ ++#define PCIE_PHYSR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x810) ++ ++/* PHY Control Register, all zeros in VR9 */ ++#define PCIE_PHYCR(X) (volatile u32*)(PCIE_RC_PORT_TO_BASE(X) + 0x814) ++ ++/* ++ * PCIe PDI PHY register definition, suppose all the following ++ * stuff is confidential. ++ * XXX, detailed bit definition ++ */ ++#define PCIE_PHY_PLL_CTRL1(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x22 << 1)) ++#define PCIE_PHY_PLL_CTRL2(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x23 << 1)) ++#define PCIE_PHY_PLL_CTRL3(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x24 << 1)) ++#define PCIE_PHY_PLL_CTRL4(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x25 << 1)) ++#define PCIE_PHY_PLL_CTRL5(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x26 << 1)) ++#define PCIE_PHY_PLL_CTRL6(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x27 << 1)) ++#define PCIE_PHY_PLL_CTRL7(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x28 << 1)) ++#define PCIE_PHY_PLL_A_CTRL1(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x29 << 1)) ++#define PCIE_PHY_PLL_A_CTRL2(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x2A << 1)) ++#define PCIE_PHY_PLL_A_CTRL3(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x2B << 1)) ++#define PCIE_PHY_PLL_STATUS(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x2C << 1)) ++ ++#define PCIE_PHY_TX1_CTRL1(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x30 << 1)) ++#define PCIE_PHY_TX1_CTRL2(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x31 << 1)) ++#define PCIE_PHY_TX1_CTRL3(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x32 << 1)) ++#define PCIE_PHY_TX1_A_CTRL1(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x33 << 1)) ++#define PCIE_PHY_TX1_A_CTRL2(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x34 << 1)) ++#define PCIE_PHY_TX1_MOD1(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x35 << 1)) ++#define PCIE_PHY_TX1_MOD2(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x36 << 1)) ++#define PCIE_PHY_TX1_MOD3(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x37 << 1)) ++ ++#define PCIE_PHY_TX2_CTRL1(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x38 << 1)) ++#define PCIE_PHY_TX2_CTRL2(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x39 << 1)) ++#define PCIE_PHY_TX2_A_CTRL1(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x3B << 1)) ++#define PCIE_PHY_TX2_A_CTRL2(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x3C << 1)) ++#define PCIE_PHY_TX2_MOD1(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x3D << 1)) ++#define PCIE_PHY_TX2_MOD2(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x3E << 1)) ++#define PCIE_PHY_TX2_MOD3(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x3F << 1)) ++ ++#define PCIE_PHY_RX1_CTRL1(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x50 << 1)) ++#define PCIE_PHY_RX1_CTRL2(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x51 << 1)) ++#define PCIE_PHY_RX1_CDR(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x52 << 1)) ++#define PCIE_PHY_RX1_EI(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x53 << 1)) ++#define PCIE_PHY_RX1_A_CTRL(X) (PCIE_PHY_PORT_TO_BASE(X) + (0x55 << 1)) ++ ++/* Interrupt related stuff */ ++#define PCIE_LEGACY_DISABLE 0 ++#define PCIE_LEGACY_INTA 1 ++#define PCIE_LEGACY_INTB 2 ++#define PCIE_LEGACY_INTC 3 ++#define PCIE_LEGACY_INTD 4 ++#define PCIE_LEGACY_INT_MAX PCIE_LEGACY_INTD ++ ++#define PCIE_IRQ_LOCK(lock) do { \ ++ unsigned long flags; \ ++ spin_lock_irqsave(&(lock), flags); ++#define PCIE_IRQ_UNLOCK(lock) \ ++ spin_unlock_irqrestore(&(lock), flags); \ ++} while (0) ++ ++#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,18) ++#define IRQF_SHARED SA_SHIRQ ++#endif ++ ++#define PCIE_MSG_MSI 0x00000001 ++#define PCIE_MSG_ISR 0x00000002 ++#define PCIE_MSG_FIXUP 0x00000004 ++#define PCIE_MSG_READ_CFG 0x00000008 ++#define PCIE_MSG_WRITE_CFG 0x00000010 ++#define PCIE_MSG_CFG (PCIE_MSG_READ_CFG | PCIE_MSG_WRITE_CFG) ++#define PCIE_MSG_REG 0x00000020 ++#define PCIE_MSG_INIT 0x00000040 ++#define PCIE_MSG_ERR 0x00000080 ++#define PCIE_MSG_PHY 0x00000100 ++#define PCIE_MSG_ANY 0x000001ff ++ ++#define IFX_PCIE_PORT0 0 ++#define IFX_PCIE_PORT1 1 ++ ++#ifdef CONFIG_IFX_PCIE_2ND_CORE ++#define IFX_PCIE_CORE_NR 2 ++#else ++#define IFX_PCIE_CORE_NR 1 ++#endif ++ ++//#define IFX_PCIE_ERROR_INT ++ ++//#define IFX_PCIE_DBG ++ ++#if defined(IFX_PCIE_DBG) ++#define IFX_PCIE_PRINT(_m, _fmt, args...) do { \ ++ if (g_pcie_debug_flag & (_m)) { \ ++ ifx_pcie_debug((_fmt), ##args); \ ++ } \ ++} while (0) ++ ++#define INLINE ++#else ++#define IFX_PCIE_PRINT(_m, _fmt, args...) \ ++ do {} while(0) ++#define INLINE inline ++#endif ++ ++struct ifx_pci_controller { ++ struct pci_controller pcic; ++ ++ /* RC specific, per host bus information */ ++ u32 port; /* Port index, 0 -- 1st core, 1 -- 2nd core */ ++}; ++ ++typedef struct ifx_pcie_ir_irq { ++ const unsigned int irq; ++ const char name[16]; ++}ifx_pcie_ir_irq_t; ++ ++typedef struct ifx_pcie_legacy_irq{ ++ const u32 irq_bit; ++ const int irq; ++}ifx_pcie_legacy_irq_t; ++ ++typedef struct ifx_pcie_irq { ++ ifx_pcie_ir_irq_t ir_irq; ++ ifx_pcie_legacy_irq_t legacy_irq[PCIE_LEGACY_INT_MAX]; ++}ifx_pcie_irq_t; ++ ++extern u32 g_pcie_debug_flag; ++extern void ifx_pcie_debug(const char *fmt, ...); ++extern void pcie_phy_clock_mode_setup(int pcie_port); ++extern void pcie_msi_pic_init(int pcie_port); ++extern u32 ifx_pcie_bus_enum_read_hack(int where, u32 value); ++extern u32 ifx_pcie_bus_enum_write_hack(int where, u32 value); ++ ++ ++#include ++#include ++#include ++#include ++ ++#include ++ ++#define IFX_PCIE_GPIO_RESET 38 ++#define IFX_REG_R32 ltq_r32 ++#define IFX_REG_W32 ltq_w32 ++#define CONFIG_IFX_PCIE_HW_SWAP ++#define IFX_RCU_AHB_ENDIAN ((volatile u32*)(IFX_RCU + 0x004C)) ++#define IFX_RCU_RST_REQ ((volatile u32*)(IFX_RCU + 0x0010)) ++#define IFX_RCU_AHB_BE_PCIE_PDI 0x00000080 /* Configure PCIE PDI module in big endian*/ ++ ++#define IFX_RCU (KSEG1 | 0x1F203000) ++#define IFX_RCU_AHB_BE_PCIE_M 0x00000001 /* Configure AHB master port that connects to PCIe RC in big endian */ ++#define IFX_RCU_AHB_BE_PCIE_S 0x00000010 /* Configure AHB slave port that connects to PCIe RC in little endian */ ++#define IFX_RCU_AHB_BE_XBAR_M 0x00000002 /* Configure AHB master port that connects to XBAR in big endian */ ++#define CONFIG_IFX_PCIE_PHY_36MHZ_MODE ++ ++#define IFX_PMU1_MODULE_PCIE_PHY (0) ++#define IFX_PMU1_MODULE_PCIE_CTRL (1) ++#define IFX_PMU1_MODULE_PDI (4) ++#define IFX_PMU1_MODULE_MSI (5) ++ ++#define IFX_PMU_MODULE_PCIE_L0_CLK (31) ++ ++ ++static inline void pcie_ep_gpio_rst_init(int pcie_port) ++{ ++} ++ ++static inline void pcie_ahb_pmu_setup(void) ++{ ++ struct clk *clk; ++ clk = clk_get_sys("ltq_pcie", "ahb"); ++ clk_enable(clk); ++ //ltq_pmu_enable(PMU_AHBM | PMU_AHBS); ++} ++ ++static inline void pcie_rcu_endian_setup(int pcie_port) ++{ ++ u32 reg; ++ ++ reg = IFX_REG_R32(IFX_RCU_AHB_ENDIAN); ++#ifdef CONFIG_IFX_PCIE_HW_SWAP ++ reg |= IFX_RCU_AHB_BE_PCIE_M; ++ reg |= IFX_RCU_AHB_BE_PCIE_S; ++ reg &= ~IFX_RCU_AHB_BE_XBAR_M; ++#else ++ reg |= IFX_RCU_AHB_BE_PCIE_M; ++ reg &= ~IFX_RCU_AHB_BE_PCIE_S; ++ reg &= ~IFX_RCU_AHB_BE_XBAR_M; ++#endif /* CONFIG_IFX_PCIE_HW_SWAP */ ++ IFX_REG_W32(reg, IFX_RCU_AHB_ENDIAN); ++ IFX_PCIE_PRINT(PCIE_MSG_REG, "%s IFX_RCU_AHB_ENDIAN: 0x%08x\n", __func__, IFX_REG_R32(IFX_RCU_AHB_ENDIAN)); ++} ++ ++static inline void pcie_phy_pmu_enable(int pcie_port) ++{ ++ struct clk *clk; ++ clk = clk_get_sys("ltq_pcie", "phy"); ++ clk_enable(clk); ++ //ltq_pmu1_enable(1<PCIe and PDI endianness */ ++ reg |= IFX_RCU_AHB_BE_PCIE_PDI; ++ IFX_REG_W32(reg, IFX_RCU_AHB_ENDIAN); ++} ++ ++static inline void pcie_pdi_pmu_enable(int pcie_port) ++{ ++ struct clk *clk; ++ clk = clk_get_sys("ltq_pcie", "pdi"); ++ clk_enable(clk); ++ //ltq_pmu1_enable(1< 1) { ++ tbus_number -= pcibios_1st_host_bus_nr(); ++ } ++#endif /* CONFIG_PCI_LANTIQ */ ++ return tbus_number; ++} ++ ++static inline u32 ++ifx_pcie_bus_enum_hack(struct pci_bus *bus, u32 devfn, int where, u32 value, int pcie_port, int read) ++{ ++ struct pci_dev *pdev; ++ u32 tvalue = value; ++ ++ /* Sanity check */ ++ pdev = pci_get_slot(bus, devfn); ++ if (pdev == NULL) { ++ return tvalue; ++ } ++ ++ /* Only care about PCI bridge */ ++ if (pdev->hdr_type != PCI_HEADER_TYPE_BRIDGE) { ++ return tvalue; ++ } ++ ++ if (read) { /* Read hack */ ++ #ifdef CONFIG_PCI_LANTIQ ++ if (pcibios_host_nr() > 1) { ++ tvalue = ifx_pcie_bus_enum_read_hack(where, tvalue); ++ } ++ #endif /* CONFIG_PCI_LANTIQ */ ++ } ++ else { /* Write hack */ ++ #ifdef CONFIG_PCI_LANTIQ ++ if (pcibios_host_nr() > 1) { ++ tvalue = ifx_pcie_bus_enum_write_hack(where, tvalue); ++ } ++ #endif ++ } ++ return tvalue; ++} ++ ++#endif /* IFXMIPS_PCIE_VR9_H */ ++ +--- a/drivers/pci/pcie/aer/Kconfig ++++ b/drivers/pci/pcie/aer/Kconfig +@@ -19,6 +19,7 @@ config PCIEAER + config PCIE_ECRC + bool "PCI Express ECRC settings control" + depends on PCIEAER ++ default n + help + Used to override firmware/bios settings for PCI Express ECRC + (transaction layer end-to-end CRC checking). +--- a/include/linux/pci.h ++++ b/include/linux/pci.h +@@ -1302,6 +1302,8 @@ void pci_walk_bus(struct pci_bus *top, i + void *userdata); + int pci_cfg_space_size(struct pci_dev *dev); + unsigned char pci_bus_max_busnr(struct pci_bus *bus); ++int pcibios_host_nr(void); ++int pcibios_1st_host_bus_nr(void); + void pci_setup_bridge(struct pci_bus *bus); + resource_size_t pcibios_window_alignment(struct pci_bus *bus, + unsigned long type); +--- a/include/linux/pci_ids.h ++++ b/include/linux/pci_ids.h +@@ -1061,6 +1061,12 @@ + #define PCI_DEVICE_ID_SGI_LITHIUM 0x1002 + #define PCI_DEVICE_ID_SGI_IOC4 0x100a + ++#define PCI_VENDOR_ID_INFINEON 0x15D1 ++#define PCI_DEVICE_ID_INFINEON_DANUBE 0x000F ++#define PCI_DEVICE_ID_INFINEON_PCIE 0x0011 ++#define PCI_VENDOR_ID_LANTIQ 0x1BEF ++#define PCI_DEVICE_ID_LANTIQ_PCIE 0x0011 ++ + #define PCI_VENDOR_ID_WINBOND 0x10ad + #define PCI_DEVICE_ID_WINBOND_82C105 0x0105 + #define PCI_DEVICE_ID_WINBOND_83C553 0x0565 diff --git a/target/linux/lantiq/patches-4.19/0002-gpio-stp-xway-Implement-get-callback.patch b/target/linux/lantiq/patches-4.19/0002-gpio-stp-xway-Implement-get-callback.patch new file mode 100644 index 0000000000..c32b3d6bba --- /dev/null +++ b/target/linux/lantiq/patches-4.19/0002-gpio-stp-xway-Implement-get-callback.patch @@ -0,0 +1,47 @@ +From 5b9b2b5284f81941972105b13337c58489ea8fca Mon Sep 17 00:00:00 2001 +From: Mathias Kresin +Date: Thu, 28 Jun 2018 21:57:40 +0200 +Subject: [PATCH] gpio: stp-xway: Implement get callback + +Add an implementation to get the current GPIO state. + +The callback is used by the leds-gpio driver for example, in case the +current LED/GPIO state should be kept during driver load. + +Signed-off-by: Mathias Kresin +Signed-off-by: Linus Walleij +--- + drivers/gpio/gpio-stp-xway.c | 15 +++++++++++++++ + 1 file changed, 15 insertions(+) + +--- a/drivers/gpio/gpio-stp-xway.c ++++ b/drivers/gpio/gpio-stp-xway.c +@@ -91,6 +91,20 @@ struct xway_stp { + }; + + /** ++ * xway_stp_get() - gpio_chip->get - get gpios. ++ * @gc: Pointer to gpio_chip device structure. ++ * @gpio: GPIO signal number. ++ * ++ * Gets the shadow value. ++ */ ++static int xway_stp_get(struct gpio_chip *gc, unsigned int gpio) ++{ ++ struct xway_stp *chip = gpiochip_get_data(gc); ++ ++ return (xway_stp_r32(chip->virt, XWAY_STP_CPU0) & BIT(gpio)); ++} ++ ++/** + * xway_stp_set() - gpio_chip->set - set gpios. + * @gc: Pointer to gpio_chip device structure. + * @gpio: GPIO signal number. +@@ -215,6 +229,7 @@ static int xway_stp_probe(struct platfor + chip->gc.parent = &pdev->dev; + chip->gc.label = "stp-xway"; + chip->gc.direction_output = xway_stp_dir_out; ++ chip->gc.get = xway_stp_get; + chip->gc.set = xway_stp_set; + chip->gc.request = xway_stp_request; + chip->gc.base = -1; diff --git a/target/linux/lantiq/patches-4.19/0004-MIPS-lantiq-add-atm-hack.patch b/target/linux/lantiq/patches-4.19/0004-MIPS-lantiq-add-atm-hack.patch new file mode 100644 index 0000000000..66ca2fd5ac --- /dev/null +++ b/target/linux/lantiq/patches-4.19/0004-MIPS-lantiq-add-atm-hack.patch @@ -0,0 +1,480 @@ +From 9afadf01b1be371ee88491819aa67364684461f9 Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Fri, 3 Aug 2012 10:27:25 +0200 +Subject: [PATCH 04/36] MIPS: lantiq: add atm hack + +Signed-off-by: John Crispin +--- + arch/mips/include/asm/mach-lantiq/lantiq_atm.h | 196 +++++++++++++++++++++++ + arch/mips/include/asm/mach-lantiq/lantiq_ptm.h | 203 ++++++++++++++++++++++++ + arch/mips/lantiq/irq.c | 2 + + arch/mips/mm/cache.c | 2 + + include/uapi/linux/atm.h | 6 + + net/atm/common.c | 6 + + net/atm/proc.c | 2 +- + 7 files changed, 416 insertions(+), 1 deletion(-) + create mode 100644 arch/mips/include/asm/mach-lantiq/lantiq_atm.h + create mode 100644 arch/mips/include/asm/mach-lantiq/lantiq_ptm.h + +--- /dev/null ++++ b/arch/mips/include/asm/mach-lantiq/lantiq_atm.h +@@ -0,0 +1,196 @@ ++/****************************************************************************** ++** ++** FILE NAME : ifx_atm.h ++** PROJECT : UEIP ++** MODULES : ATM ++** ++** DATE : 17 Jun 2009 ++** AUTHOR : Xu Liang ++** DESCRIPTION : Global ATM driver header file ++** COPYRIGHT : Copyright (c) 2006 ++** Infineon Technologies AG ++** Am Campeon 1-12, 85579 Neubiberg, Germany ++** ++** This program is free software; you can redistribute it and/or modify ++** it under the terms of the GNU General Public License as published by ++** the Free Software Foundation; either version 2 of the License, or ++** (at your option) any later version. ++** ++** HISTORY ++** $Date $Author $Comment ++** 07 JUL 2009 Xu Liang Init Version ++*******************************************************************************/ ++ ++#ifndef IFX_ATM_H ++#define IFX_ATM_H ++ ++ ++ ++/*! ++ \defgroup IFX_ATM UEIP Project - ATM driver module ++ \brief UEIP Project - ATM driver module, support Danube, Amazon-SE, AR9, VR9. ++ */ ++ ++/*! ++ \defgroup IFX_ATM_IOCTL IOCTL Commands ++ \ingroup IFX_ATM ++ \brief IOCTL Commands used by user application. ++ */ ++ ++/*! ++ \defgroup IFX_ATM_STRUCT Structures ++ \ingroup IFX_ATM ++ \brief Structures used by user application. ++ */ ++ ++/*! ++ \file ifx_atm.h ++ \ingroup IFX_ATM ++ \brief ATM driver header file ++ */ ++ ++ ++ ++/* ++ * #################################### ++ * Definition ++ * #################################### ++ */ ++ ++/*! ++ \addtogroup IFX_ATM_STRUCT ++ */ ++/*@{*/ ++ ++/* ++ * ATM MIB ++ */ ++ ++/*! ++ \struct atm_cell_ifEntry_t ++ \brief Structure used for Cell Level MIB Counters. ++ ++ User application use this structure to call IOCTL command "PPE_ATM_MIB_CELL". ++ */ ++typedef struct { ++ __u32 ifHCInOctets_h; /*!< byte counter of ingress cells (upper 32 bits, total 64 bits) */ ++ __u32 ifHCInOctets_l; /*!< byte counter of ingress cells (lower 32 bits, total 64 bits) */ ++ __u32 ifHCOutOctets_h; /*!< byte counter of egress cells (upper 32 bits, total 64 bits) */ ++ __u32 ifHCOutOctets_l; /*!< byte counter of egress cells (lower 32 bits, total 64 bits) */ ++ __u32 ifInErrors; /*!< counter of error ingress cells */ ++ __u32 ifInUnknownProtos; /*!< counter of unknown ingress cells */ ++ __u32 ifOutErrors; /*!< counter of error egress cells */ ++} atm_cell_ifEntry_t; ++ ++/*! ++ \struct atm_aal5_ifEntry_t ++ \brief Structure used for AAL5 Frame Level MIB Counters. ++ ++ User application use this structure to call IOCTL command "PPE_ATM_MIB_AAL5". ++ */ ++typedef struct { ++ __u32 ifHCInOctets_h; /*!< byte counter of ingress packets (upper 32 bits, total 64 bits) */ ++ __u32 ifHCInOctets_l; /*!< byte counter of ingress packets (lower 32 bits, total 64 bits) */ ++ __u32 ifHCOutOctets_h; /*!< byte counter of egress packets (upper 32 bits, total 64 bits) */ ++ __u32 ifHCOutOctets_l; /*!< byte counter of egress packets (lower 32 bits, total 64 bits) */ ++ __u32 ifInUcastPkts; /*!< counter of ingress packets */ ++ __u32 ifOutUcastPkts; /*!< counter of egress packets */ ++ __u32 ifInErrors; /*!< counter of error ingress packets */ ++ __u32 ifInDiscards; /*!< counter of dropped ingress packets */ ++ __u32 ifOutErros; /*!< counter of error egress packets */ ++ __u32 ifOutDiscards; /*!< counter of dropped egress packets */ ++} atm_aal5_ifEntry_t; ++ ++/*! ++ \struct atm_aal5_vcc_t ++ \brief Structure used for per PVC AAL5 Frame Level MIB Counters. ++ ++ This structure is a part of structure "atm_aal5_vcc_x_t". ++ */ ++typedef struct { ++ __u32 aal5VccCrcErrors; /*!< counter of ingress packets with CRC error */ ++ __u32 aal5VccSarTimeOuts; /*!< counter of ingress packets with Re-assemble timeout */ //no timer support yet ++ __u32 aal5VccOverSizedSDUs; /*!< counter of oversized ingress packets */ ++} atm_aal5_vcc_t; ++ ++/*! ++ \struct atm_aal5_vcc_x_t ++ \brief Structure used for per PVC AAL5 Frame Level MIB Counters. ++ ++ User application use this structure to call IOCTL command "PPE_ATM_MIB_VCC". ++ */ ++typedef struct { ++ int vpi; /*!< VPI of the VCC to get MIB counters */ ++ int vci; /*!< VCI of the VCC to get MIB counters */ ++ atm_aal5_vcc_t mib_vcc; /*!< structure to get MIB counters */ ++} atm_aal5_vcc_x_t; ++ ++/*@}*/ ++ ++ ++ ++/* ++ * #################################### ++ * IOCTL ++ * #################################### ++ */ ++ ++/*! ++ \addtogroup IFX_ATM_IOCTL ++ */ ++/*@{*/ ++ ++/* ++ * ioctl Command ++ */ ++/*! ++ \brief ATM IOCTL Magic Number ++ */ ++#define PPE_ATM_IOC_MAGIC 'o' ++/*! ++ \brief ATM IOCTL Command - Get Cell Level MIB Counters ++ ++ This command is obsolete. User can get cell level MIB from DSL API. ++ This command uses structure "atm_cell_ifEntry_t" as parameter for output of MIB counters. ++ */ ++#define PPE_ATM_MIB_CELL _IOW(PPE_ATM_IOC_MAGIC, 0, atm_cell_ifEntry_t) ++/*! ++ \brief ATM IOCTL Command - Get AAL5 Level MIB Counters ++ ++ Get AAL5 packet counters. ++ This command uses structure "atm_aal5_ifEntry_t" as parameter for output of MIB counters. ++ */ ++#define PPE_ATM_MIB_AAL5 _IOW(PPE_ATM_IOC_MAGIC, 1, atm_aal5_ifEntry_t) ++/*! ++ \brief ATM IOCTL Command - Get Per PVC MIB Counters ++ ++ Get AAL5 packet counters for each PVC. ++ This command uses structure "atm_aal5_vcc_x_t" as parameter for input of VPI/VCI information and output of MIB counters. ++ */ ++#define PPE_ATM_MIB_VCC _IOWR(PPE_ATM_IOC_MAGIC, 2, atm_aal5_vcc_x_t) ++/*! ++ \brief Total Number of ATM IOCTL Commands ++ */ ++#define PPE_ATM_IOC_MAXNR 3 ++ ++/*@}*/ ++ ++ ++ ++/* ++ * #################################### ++ * API ++ * #################################### ++ */ ++ ++#ifdef __KERNEL__ ++struct port_cell_info { ++ unsigned int port_num; ++ unsigned int tx_link_rate[2]; ++}; ++#endif ++ ++ ++ ++#endif // IFX_ATM_H ++ +--- /dev/null ++++ b/arch/mips/include/asm/mach-lantiq/lantiq_ptm.h +@@ -0,0 +1,203 @@ ++/****************************************************************************** ++** ++** FILE NAME : ifx_ptm.h ++** PROJECT : UEIP ++** MODULES : PTM ++** ++** DATE : 17 Jun 2009 ++** AUTHOR : Xu Liang ++** DESCRIPTION : Global PTM driver header file ++** COPYRIGHT : Copyright (c) 2006 ++** Infineon Technologies AG ++** Am Campeon 1-12, 85579 Neubiberg, Germany ++** ++** This program is free software; you can redistribute it and/or modify ++** it under the terms of the GNU General Public License as published by ++** the Free Software Foundation; either version 2 of the License, or ++** (at your option) any later version. ++** ++** HISTORY ++** $Date $Author $Comment ++** 07 JUL 2009 Xu Liang Init Version ++*******************************************************************************/ ++ ++#ifndef IFX_PTM_H ++#define IFX_PTM_H ++ ++ ++ ++/*! ++ \defgroup IFX_PTM UEIP Project - PTM driver module ++ \brief UEIP Project - PTM driver module, support Danube, Amazon-SE, AR9, VR9. ++ */ ++ ++/*! ++ \defgroup IFX_PTM_IOCTL IOCTL Commands ++ \ingroup IFX_PTM ++ \brief IOCTL Commands used by user application. ++ */ ++ ++/*! ++ \defgroup IFX_PTM_STRUCT Structures ++ \ingroup IFX_PTM ++ \brief Structures used by user application. ++ */ ++ ++/*! ++ \file ifx_ptm.h ++ \ingroup IFX_PTM ++ \brief PTM driver header file ++ */ ++ ++ ++ ++/* ++ * #################################### ++ * Definition ++ * #################################### ++ */ ++ ++ ++ ++/* ++ * #################################### ++ * IOCTL ++ * #################################### ++ */ ++ ++/*! ++ \addtogroup IFX_PTM_IOCTL ++ */ ++/*@{*/ ++ ++/* ++ * ioctl Command ++ */ ++/*! ++ \brief PTM IOCTL Command - Get codeword MIB counters. ++ ++ This command uses structure "PTM_CW_IF_ENTRY_T" to get codeword level MIB counters. ++ */ ++#define IFX_PTM_MIB_CW_GET SIOCDEVPRIVATE + 1 ++/*! ++ \brief PTM IOCTL Command - Get packet MIB counters. ++ ++ This command uses structure "PTM_FRAME_MIB_T" to get packet level MIB counters. ++ */ ++#define IFX_PTM_MIB_FRAME_GET SIOCDEVPRIVATE + 2 ++/*! ++ \brief PTM IOCTL Command - Get firmware configuration (CRC). ++ ++ This command uses structure "IFX_PTM_CFG_T" to get firmware configuration (CRC). ++ */ ++#define IFX_PTM_CFG_GET SIOCDEVPRIVATE + 3 ++/*! ++ \brief PTM IOCTL Command - Set firmware configuration (CRC). ++ ++ This command uses structure "IFX_PTM_CFG_T" to set firmware configuration (CRC). ++ */ ++#define IFX_PTM_CFG_SET SIOCDEVPRIVATE + 4 ++/*! ++ \brief PTM IOCTL Command - Program priority value to TX queue mapping. ++ ++ This command uses structure "IFX_PTM_PRIO_Q_MAP_T" to program priority value to TX queue mapping. ++ */ ++#define IFX_PTM_MAP_PKT_PRIO_TO_Q SIOCDEVPRIVATE + 14 ++ ++/*@}*/ ++ ++ ++/*! ++ \addtogroup IFX_PTM_STRUCT ++ */ ++/*@{*/ ++ ++/* ++ * ioctl Data Type ++ */ ++ ++/*! ++ \typedef PTM_CW_IF_ENTRY_T ++ \brief Wrapping of structure "ptm_cw_ifEntry_t". ++ */ ++/*! ++ \struct ptm_cw_ifEntry_t ++ \brief Structure used for CodeWord level MIB counters. ++ */ ++typedef struct ptm_cw_ifEntry_t { ++ uint32_t ifRxNoIdleCodewords; /*!< output, number of ingress user codeword */ ++ uint32_t ifRxIdleCodewords; /*!< output, number of ingress idle codeword */ ++ uint32_t ifRxCodingViolation; /*!< output, number of error ingress codeword */ ++ uint32_t ifTxNoIdleCodewords; /*!< output, number of egress user codeword */ ++ uint32_t ifTxIdleCodewords; /*!< output, number of egress idle codeword */ ++} PTM_CW_IF_ENTRY_T; ++ ++/*! ++ \typedef PTM_FRAME_MIB_T ++ \brief Wrapping of structure "ptm_frame_mib_t". ++ */ ++/*! ++ \struct ptm_frame_mib_t ++ \brief Structure used for packet level MIB counters. ++ */ ++typedef struct ptm_frame_mib_t { ++ uint32_t RxCorrect; /*!< output, number of ingress packet */ ++ uint32_t TC_CrcError; /*!< output, number of egress packet with CRC error */ ++ uint32_t RxDropped; /*!< output, number of dropped ingress packet */ ++ uint32_t TxSend; /*!< output, number of egress packet */ ++} PTM_FRAME_MIB_T; ++ ++/*! ++ \typedef IFX_PTM_CFG_T ++ \brief Wrapping of structure "ptm_cfg_t". ++ */ ++/*! ++ \struct ptm_cfg_t ++ \brief Structure used for ETH/TC CRC configuration. ++ */ ++typedef struct ptm_cfg_t { ++ uint32_t RxEthCrcPresent; /*!< input/output, ingress packet has ETH CRC */ ++ uint32_t RxEthCrcCheck; /*!< input/output, check ETH CRC of ingress packet */ ++ uint32_t RxTcCrcCheck; /*!< input/output, check TC CRC of ingress codeword */ ++ uint32_t RxTcCrcLen; /*!< input/output, length of TC CRC of ingress codeword */ ++ uint32_t TxEthCrcGen; /*!< input/output, generate ETH CRC for egress packet */ ++ uint32_t TxTcCrcGen; /*!< input/output, generate TC CRC for egress codeword */ ++ uint32_t TxTcCrcLen; /*!< input/output, length of TC CRC of egress codeword */ ++} IFX_PTM_CFG_T; ++ ++/*! ++ \typedef IFX_PTM_PRIO_Q_MAP_T ++ \brief Wrapping of structure "ppe_prio_q_map". ++ */ ++/*! ++ \struct ppe_prio_q_map ++ \brief Structure used for Priority Value to TX Queue mapping. ++ */ ++typedef struct ppe_prio_q_map { ++ int pkt_prio; ++ int qid; ++ int vpi; // ignored in eth interface ++ int vci; // ignored in eth interface ++} IFX_PTM_PRIO_Q_MAP_T; ++ ++/*@}*/ ++ ++ ++ ++/* ++ * #################################### ++ * API ++ * #################################### ++ */ ++ ++#ifdef __KERNEL__ ++struct port_cell_info { ++ unsigned int port_num; ++ unsigned int tx_link_rate[2]; ++}; ++#endif ++ ++ ++ ++#endif // IFX_PTM_H ++ +--- a/arch/mips/lantiq/irq.c ++++ b/arch/mips/lantiq/irq.c +@@ -14,6 +14,7 @@ + #include + #include + #include ++#include + + #include + #include +@@ -96,6 +97,7 @@ void ltq_mask_and_ack_irq(struct irq_dat + ltq_icu_w32(im, ltq_icu_r32(im, ier) & ~BIT(offset), ier); + ltq_icu_w32(im, BIT(offset), isr); + } ++EXPORT_SYMBOL(ltq_mask_and_ack_irq); + + static void ltq_ack_irq(struct irq_data *d) + { +--- a/arch/mips/mm/cache.c ++++ b/arch/mips/mm/cache.c +@@ -64,6 +64,8 @@ void (*_dma_cache_wback)(unsigned long s + void (*_dma_cache_inv)(unsigned long start, unsigned long size); + + EXPORT_SYMBOL(_dma_cache_wback_inv); ++EXPORT_SYMBOL(_dma_cache_wback); ++EXPORT_SYMBOL(_dma_cache_inv); + + #endif /* CONFIG_DMA_NONCOHERENT || CONFIG_DMA_MAYBE_COHERENT */ + +--- a/include/uapi/linux/atm.h ++++ b/include/uapi/linux/atm.h +@@ -131,8 +131,14 @@ + #define ATM_ABR 4 + #define ATM_ANYCLASS 5 /* compatible with everything */ + ++#define ATM_VBR_NRT ATM_VBR ++#define ATM_VBR_RT 6 ++#define ATM_UBR_PLUS 7 ++#define ATM_GFR 8 ++ + #define ATM_MAX_PCR -1 /* maximum available PCR */ + ++ + struct atm_trafprm { + unsigned char traffic_class; /* traffic class (ATM_UBR, ...) */ + int max_pcr; /* maximum PCR in cells per second */ +--- a/net/atm/proc.c ++++ b/net/atm/proc.c +@@ -155,7 +155,7 @@ static void *vcc_seq_next(struct seq_fil + static void pvc_info(struct seq_file *seq, struct atm_vcc *vcc) + { + static const char *const class_name[] = { +- "off", "UBR", "CBR", "VBR", "ABR"}; ++ "off","UBR","CBR","NTR-VBR","ABR","ANY","RT-VBR","UBR+","GFR"}; + static const char *const aal_name[] = { + "---", "1", "2", "3/4", /* 0- 3 */ + "???", "5", "???", "???", /* 4- 7 */ diff --git a/target/linux/lantiq/patches-4.19/0008-MIPS-lantiq-backport-old-timer-code.patch b/target/linux/lantiq/patches-4.19/0008-MIPS-lantiq-backport-old-timer-code.patch new file mode 100644 index 0000000000..52e4cbeb1b --- /dev/null +++ b/target/linux/lantiq/patches-4.19/0008-MIPS-lantiq-backport-old-timer-code.patch @@ -0,0 +1,1034 @@ +From 94800350cb8d2f29dda2206b5e9a3772024ee168 Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Thu, 7 Aug 2014 18:30:56 +0200 +Subject: [PATCH 08/36] MIPS: lantiq: backport old timer code + +Signed-off-by: John Crispin +--- + arch/mips/include/asm/mach-lantiq/lantiq_timer.h | 155 ++++ + arch/mips/lantiq/xway/Makefile | 2 +- + arch/mips/lantiq/xway/timer.c | 845 ++++++++++++++++++++++ + 3 files changed, 1001 insertions(+), 1 deletion(-) + create mode 100644 arch/mips/include/asm/mach-lantiq/lantiq_timer.h + create mode 100644 arch/mips/lantiq/xway/timer.c + +--- /dev/null ++++ b/arch/mips/include/asm/mach-lantiq/lantiq_timer.h +@@ -0,0 +1,155 @@ ++#ifndef __DANUBE_GPTU_DEV_H__2005_07_26__10_19__ ++#define __DANUBE_GPTU_DEV_H__2005_07_26__10_19__ ++ ++ ++/****************************************************************************** ++ Copyright (c) 2002, Infineon Technologies. All rights reserved. ++ ++ No Warranty ++ Because the program is licensed free of charge, there is no warranty for ++ the program, to the extent permitted by applicable law. Except when ++ otherwise stated in writing the copyright holders and/or other parties ++ provide the program "as is" without warranty of any kind, either ++ expressed or implied, including, but not limited to, the implied ++ warranties of merchantability and fitness for a particular purpose. The ++ entire risk as to the quality and performance of the program is with ++ you. should the program prove defective, you assume the cost of all ++ necessary servicing, repair or correction. ++ ++ In no event unless required by applicable law or agreed to in writing ++ will any copyright holder, or any other party who may modify and/or ++ redistribute the program as permitted above, be liable to you for ++ damages, including any general, special, incidental or consequential ++ damages arising out of the use or inability to use the program ++ (including but not limited to loss of data or data being rendered ++ inaccurate or losses sustained by you or third parties or a failure of ++ the program to operate with any other programs), even if such holder or ++ other party has been advised of the possibility of such damages. ++******************************************************************************/ ++ ++ ++/* ++ * #################################### ++ * Definition ++ * #################################### ++ */ ++ ++/* ++ * Available Timer/Counter Index ++ */ ++#define TIMER(n, X) (n * 2 + (X ? 1 : 0)) ++#define TIMER_ANY 0x00 ++#define TIMER1A TIMER(1, 0) ++#define TIMER1B TIMER(1, 1) ++#define TIMER2A TIMER(2, 0) ++#define TIMER2B TIMER(2, 1) ++#define TIMER3A TIMER(3, 0) ++#define TIMER3B TIMER(3, 1) ++ ++/* ++ * Flag of Timer/Counter ++ * These flags specify the way in which timer is configured. ++ */ ++/* Bit size of timer/counter. */ ++#define TIMER_FLAG_16BIT 0x0000 ++#define TIMER_FLAG_32BIT 0x0001 ++/* Switch between timer and counter. */ ++#define TIMER_FLAG_TIMER 0x0000 ++#define TIMER_FLAG_COUNTER 0x0002 ++/* Stop or continue when overflowing/underflowing. */ ++#define TIMER_FLAG_ONCE 0x0000 ++#define TIMER_FLAG_CYCLIC 0x0004 ++/* Count up or counter down. */ ++#define TIMER_FLAG_UP 0x0000 ++#define TIMER_FLAG_DOWN 0x0008 ++/* Count on specific level or edge. */ ++#define TIMER_FLAG_HIGH_LEVEL_SENSITIVE 0x0000 ++#define TIMER_FLAG_LOW_LEVEL_SENSITIVE 0x0040 ++#define TIMER_FLAG_RISE_EDGE 0x0010 ++#define TIMER_FLAG_FALL_EDGE 0x0020 ++#define TIMER_FLAG_ANY_EDGE 0x0030 ++/* Signal is syncronous to module clock or not. */ ++#define TIMER_FLAG_UNSYNC 0x0000 ++#define TIMER_FLAG_SYNC 0x0080 ++/* Different interrupt handle type. */ ++#define TIMER_FLAG_NO_HANDLE 0x0000 ++#if defined(__KERNEL__) ++ #define TIMER_FLAG_CALLBACK_IN_IRQ 0x0100 ++#endif // defined(__KERNEL__) ++#define TIMER_FLAG_SIGNAL 0x0300 ++/* Internal clock source or external clock source */ ++#define TIMER_FLAG_INT_SRC 0x0000 ++#define TIMER_FLAG_EXT_SRC 0x1000 ++ ++ ++/* ++ * ioctl Command ++ */ ++#define GPTU_REQUEST_TIMER 0x01 /* General method to setup timer/counter. */ ++#define GPTU_FREE_TIMER 0x02 /* Free timer/counter. */ ++#define GPTU_START_TIMER 0x03 /* Start or resume timer/counter. */ ++#define GPTU_STOP_TIMER 0x04 /* Suspend timer/counter. */ ++#define GPTU_GET_COUNT_VALUE 0x05 /* Get current count value. */ ++#define GPTU_CALCULATE_DIVIDER 0x06 /* Calculate timer divider from given freq.*/ ++#define GPTU_SET_TIMER 0x07 /* Simplified method to setup timer. */ ++#define GPTU_SET_COUNTER 0x08 /* Simplified method to setup counter. */ ++ ++/* ++ * Data Type Used to Call ioctl ++ */ ++struct gptu_ioctl_param { ++ unsigned int timer; /* In command GPTU_REQUEST_TIMER, GPTU_SET_TIMER, and * ++ * GPTU_SET_COUNTER, this field is ID of expected * ++ * timer/counter. If it's zero, a timer/counter would * ++ * be dynamically allocated and ID would be stored in * ++ * this field. * ++ * In command GPTU_GET_COUNT_VALUE, this field is * ++ * ignored. * ++ * In other command, this field is ID of timer/counter * ++ * allocated. */ ++ unsigned int flag; /* In command GPTU_REQUEST_TIMER, GPTU_SET_TIMER, and * ++ * GPTU_SET_COUNTER, this field contains flags to * ++ * specify how to configure timer/counter. * ++ * In command GPTU_START_TIMER, zero indicate start * ++ * and non-zero indicate resume timer/counter. * ++ * In other command, this field is ignored. */ ++ unsigned long value; /* In command GPTU_REQUEST_TIMER, this field contains * ++ * init/reload value. * ++ * In command GPTU_SET_TIMER, this field contains * ++ * frequency (0.001Hz) of timer. * ++ * In command GPTU_GET_COUNT_VALUE, current count * ++ * value would be stored in this field. * ++ * In command GPTU_CALCULATE_DIVIDER, this field * ++ * contains frequency wanted, and after calculation, * ++ * divider would be stored in this field to overwrite * ++ * the frequency. * ++ * In other command, this field is ignored. */ ++ int pid; /* In command GPTU_REQUEST_TIMER and GPTU_SET_TIMER, * ++ * if signal is required, this field contains process * ++ * ID to which signal would be sent. * ++ * In other command, this field is ignored. */ ++ int sig; /* In command GPTU_REQUEST_TIMER and GPTU_SET_TIMER, * ++ * if signal is required, this field contains signal * ++ * number which would be sent. * ++ * In other command, this field is ignored. */ ++}; ++ ++/* ++ * #################################### ++ * Data Type ++ * #################################### ++ */ ++typedef void (*timer_callback)(unsigned long arg); ++ ++extern int lq_request_timer(unsigned int, unsigned int, unsigned long, unsigned long, unsigned long); ++extern int lq_free_timer(unsigned int); ++extern int lq_start_timer(unsigned int, int); ++extern int lq_stop_timer(unsigned int); ++extern int lq_reset_counter_flags(u32 timer, u32 flags); ++extern int lq_get_count_value(unsigned int, unsigned long *); ++extern u32 lq_cal_divider(unsigned long); ++extern int lq_set_timer(unsigned int, unsigned int, int, int, unsigned int, unsigned long, unsigned long); ++extern int lq_set_counter(unsigned int timer, unsigned int flag, ++ u32 reload, unsigned long arg1, unsigned long arg2); ++ ++#endif /* __DANUBE_GPTU_DEV_H__2005_07_26__10_19__ */ +--- a/arch/mips/lantiq/xway/Makefile ++++ b/arch/mips/lantiq/xway/Makefile +@@ -1,3 +1,9 @@ +-obj-y := prom.o sysctrl.o clk.o dma.o gptu.o dcdc.o ++obj-y := prom.o sysctrl.o clk.o dma.o dcdc.o ++ ++ifdef CONFIG_SOC_AMAZON_SE ++obj-y += gptu.o ++else ++obj-y += timer.o ++endif + + obj-y += vmmc.o +--- /dev/null ++++ b/arch/mips/lantiq/xway/timer.c +@@ -0,0 +1,846 @@ ++#ifndef CONFIG_SOC_AMAZON_SE ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++#include ++#include "../clk.h" ++ ++#include ++#include ++#include ++ ++#define MAX_NUM_OF_32BIT_TIMER_BLOCKS 6 ++ ++#ifdef TIMER1A ++#define FIRST_TIMER TIMER1A ++#else ++#define FIRST_TIMER 2 ++#endif ++ ++/* ++ * GPTC divider is set or not. ++ */ ++#define GPTU_CLC_RMC_IS_SET 0 ++ ++/* ++ * Timer Interrupt (IRQ) ++ */ ++/* Must be adjusted when ICU driver is available */ ++#define TIMER_INTERRUPT (INT_NUM_IM3_IRL0 + 22) ++ ++/* ++ * Bits Operation ++ */ ++#define GET_BITS(x, msb, lsb) \ ++ (((x) & ((1 << ((msb) + 1)) - 1)) >> (lsb)) ++#define SET_BITS(x, msb, lsb, value) \ ++ (((x) & ~(((1 << ((msb) + 1)) - 1) ^ ((1 << (lsb)) - 1))) | \ ++ (((value) & ((1 << (1 + (msb) - (lsb))) - 1)) << (lsb))) ++ ++/* ++ * GPTU Register Mapping ++ */ ++#define LQ_GPTU (KSEG1 + 0x1E100A00) ++#define LQ_GPTU_CLC ((volatile u32 *)(LQ_GPTU + 0x0000)) ++#define LQ_GPTU_ID ((volatile u32 *)(LQ_GPTU + 0x0008)) ++#define LQ_GPTU_CON(n, X) ((volatile u32 *)(LQ_GPTU + 0x0010 + ((X) * 4) + ((n) - 1) * 0x0020)) /* X must be either A or B */ ++#define LQ_GPTU_RUN(n, X) ((volatile u32 *)(LQ_GPTU + 0x0018 + ((X) * 4) + ((n) - 1) * 0x0020)) /* X must be either A or B */ ++#define LQ_GPTU_RELOAD(n, X) ((volatile u32 *)(LQ_GPTU + 0x0020 + ((X) * 4) + ((n) - 1) * 0x0020)) /* X must be either A or B */ ++#define LQ_GPTU_COUNT(n, X) ((volatile u32 *)(LQ_GPTU + 0x0028 + ((X) * 4) + ((n) - 1) * 0x0020)) /* X must be either A or B */ ++#define LQ_GPTU_IRNEN ((volatile u32 *)(LQ_GPTU + 0x00F4)) ++#define LQ_GPTU_IRNICR ((volatile u32 *)(LQ_GPTU + 0x00F8)) ++#define LQ_GPTU_IRNCR ((volatile u32 *)(LQ_GPTU + 0x00FC)) ++ ++/* ++ * Clock Control Register ++ */ ++#define GPTU_CLC_SMC GET_BITS(*LQ_GPTU_CLC, 23, 16) ++#define GPTU_CLC_RMC GET_BITS(*LQ_GPTU_CLC, 15, 8) ++#define GPTU_CLC_FSOE (*LQ_GPTU_CLC & (1 << 5)) ++#define GPTU_CLC_EDIS (*LQ_GPTU_CLC & (1 << 3)) ++#define GPTU_CLC_SPEN (*LQ_GPTU_CLC & (1 << 2)) ++#define GPTU_CLC_DISS (*LQ_GPTU_CLC & (1 << 1)) ++#define GPTU_CLC_DISR (*LQ_GPTU_CLC & (1 << 0)) ++ ++#define GPTU_CLC_SMC_SET(value) SET_BITS(0, 23, 16, (value)) ++#define GPTU_CLC_RMC_SET(value) SET_BITS(0, 15, 8, (value)) ++#define GPTU_CLC_FSOE_SET(value) ((value) ? (1 << 5) : 0) ++#define GPTU_CLC_SBWE_SET(value) ((value) ? (1 << 4) : 0) ++#define GPTU_CLC_EDIS_SET(value) ((value) ? (1 << 3) : 0) ++#define GPTU_CLC_SPEN_SET(value) ((value) ? (1 << 2) : 0) ++#define GPTU_CLC_DISR_SET(value) ((value) ? (1 << 0) : 0) ++ ++/* ++ * ID Register ++ */ ++#define GPTU_ID_ID GET_BITS(*LQ_GPTU_ID, 15, 8) ++#define GPTU_ID_CFG GET_BITS(*LQ_GPTU_ID, 7, 5) ++#define GPTU_ID_REV GET_BITS(*LQ_GPTU_ID, 4, 0) ++ ++/* ++ * Control Register of Timer/Counter nX ++ * n is the index of block (1 based index) ++ * X is either A or B ++ */ ++#define GPTU_CON_SRC_EG(n, X) (*LQ_GPTU_CON(n, X) & (1 << 10)) ++#define GPTU_CON_SRC_EXT(n, X) (*LQ_GPTU_CON(n, X) & (1 << 9)) ++#define GPTU_CON_SYNC(n, X) (*LQ_GPTU_CON(n, X) & (1 << 8)) ++#define GPTU_CON_EDGE(n, X) GET_BITS(*LQ_GPTU_CON(n, X), 7, 6) ++#define GPTU_CON_INV(n, X) (*LQ_GPTU_CON(n, X) & (1 << 5)) ++#define GPTU_CON_EXT(n, X) (*LQ_GPTU_CON(n, A) & (1 << 4)) /* Timer/Counter B does not have this bit */ ++#define GPTU_CON_STP(n, X) (*LQ_GPTU_CON(n, X) & (1 << 3)) ++#define GPTU_CON_CNT(n, X) (*LQ_GPTU_CON(n, X) & (1 << 2)) ++#define GPTU_CON_DIR(n, X) (*LQ_GPTU_CON(n, X) & (1 << 1)) ++#define GPTU_CON_EN(n, X) (*LQ_GPTU_CON(n, X) & (1 << 0)) ++ ++#define GPTU_CON_SRC_EG_SET(value) ((value) ? 0 : (1 << 10)) ++#define GPTU_CON_SRC_EXT_SET(value) ((value) ? (1 << 9) : 0) ++#define GPTU_CON_SYNC_SET(value) ((value) ? (1 << 8) : 0) ++#define GPTU_CON_EDGE_SET(value) SET_BITS(0, 7, 6, (value)) ++#define GPTU_CON_INV_SET(value) ((value) ? (1 << 5) : 0) ++#define GPTU_CON_EXT_SET(value) ((value) ? (1 << 4) : 0) ++#define GPTU_CON_STP_SET(value) ((value) ? (1 << 3) : 0) ++#define GPTU_CON_CNT_SET(value) ((value) ? (1 << 2) : 0) ++#define GPTU_CON_DIR_SET(value) ((value) ? (1 << 1) : 0) ++ ++#define GPTU_RUN_RL_SET(value) ((value) ? (1 << 2) : 0) ++#define GPTU_RUN_CEN_SET(value) ((value) ? (1 << 1) : 0) ++#define GPTU_RUN_SEN_SET(value) ((value) ? (1 << 0) : 0) ++ ++#define GPTU_IRNEN_TC_SET(n, X, value) ((value) ? (1 << (((n) - 1) * 2 + (X))) : 0) ++#define GPTU_IRNCR_TC_SET(n, X, value) ((value) ? (1 << (((n) - 1) * 2 + (X))) : 0) ++ ++#define TIMER_FLAG_MASK_SIZE(x) (x & 0x0001) ++#define TIMER_FLAG_MASK_TYPE(x) (x & 0x0002) ++#define TIMER_FLAG_MASK_STOP(x) (x & 0x0004) ++#define TIMER_FLAG_MASK_DIR(x) (x & 0x0008) ++#define TIMER_FLAG_NONE_EDGE 0x0000 ++#define TIMER_FLAG_MASK_EDGE(x) (x & 0x0030) ++#define TIMER_FLAG_REAL 0x0000 ++#define TIMER_FLAG_INVERT 0x0040 ++#define TIMER_FLAG_MASK_INVERT(x) (x & 0x0040) ++#define TIMER_FLAG_MASK_TRIGGER(x) (x & 0x0070) ++#define TIMER_FLAG_MASK_SYNC(x) (x & 0x0080) ++#define TIMER_FLAG_CALLBACK_IN_HB 0x0200 ++#define TIMER_FLAG_MASK_HANDLE(x) (x & 0x0300) ++#define TIMER_FLAG_MASK_SRC(x) (x & 0x1000) ++ ++struct timer_dev_timer { ++ unsigned int f_irq_on; ++ unsigned int irq; ++ unsigned int flag; ++ unsigned long arg1; ++ unsigned long arg2; ++}; ++ ++struct timer_dev { ++ struct mutex gptu_mutex; ++ unsigned int number_of_timers; ++ unsigned int occupation; ++ unsigned int f_gptu_on; ++ struct timer_dev_timer timer[MAX_NUM_OF_32BIT_TIMER_BLOCKS * 2]; ++}; ++ ++ ++unsigned int ltq_get_fpi_bus_clock(int fpi) { ++ struct clk *clk = clk_get_fpi(); ++ return clk_get_rate(clk); ++} ++ ++ ++static long gptu_ioctl(struct file *, unsigned int, unsigned long); ++static int gptu_open(struct inode *, struct file *); ++static int gptu_release(struct inode *, struct file *); ++ ++static struct file_operations gptu_fops = { ++ .owner = THIS_MODULE, ++ .unlocked_ioctl = gptu_ioctl, ++ .open = gptu_open, ++ .release = gptu_release ++}; ++ ++static struct miscdevice gptu_miscdev = { ++ .minor = MISC_DYNAMIC_MINOR, ++ .name = "gptu", ++ .fops = &gptu_fops, ++}; ++ ++static struct timer_dev timer_dev; ++ ++static irqreturn_t timer_irq_handler(int irq, void *p) ++{ ++ unsigned int timer; ++ unsigned int flag; ++ struct timer_dev_timer *dev_timer = (struct timer_dev_timer *)p; ++ ++ timer = irq - TIMER_INTERRUPT; ++ if (timer < timer_dev.number_of_timers ++ && dev_timer == &timer_dev.timer[timer]) { ++ /* Clear interrupt. */ ++ ltq_w32(1 << timer, LQ_GPTU_IRNCR); ++ ++ /* Call user hanler or signal. */ ++ flag = dev_timer->flag; ++ if (!(timer & 0x01) ++ || TIMER_FLAG_MASK_SIZE(flag) == TIMER_FLAG_16BIT) { ++ /* 16-bit timer or timer A of 32-bit timer */ ++ switch (TIMER_FLAG_MASK_HANDLE(flag)) { ++ case TIMER_FLAG_CALLBACK_IN_IRQ: ++ case TIMER_FLAG_CALLBACK_IN_HB: ++ if (dev_timer->arg1) ++ (*(timer_callback)dev_timer->arg1)(dev_timer->arg2); ++ break; ++ case TIMER_FLAG_SIGNAL: ++ send_sig((int)dev_timer->arg2, (struct task_struct *)dev_timer->arg1, 0); ++ break; ++ } ++ } ++ } ++ return IRQ_HANDLED; ++} ++ ++static inline void lq_enable_gptu(void) ++{ ++ struct clk *clk = clk_get_sys("1e100a00.gptu", NULL); ++ clk_enable(clk); ++ ++ //ltq_pmu_enable(PMU_GPT); ++ ++ /* Set divider as 1, disable write protection for SPEN, enable module. */ ++ *LQ_GPTU_CLC = ++ GPTU_CLC_SMC_SET(0x00) | ++ GPTU_CLC_RMC_SET(0x01) | ++ GPTU_CLC_FSOE_SET(0) | ++ GPTU_CLC_SBWE_SET(1) | ++ GPTU_CLC_EDIS_SET(0) | ++ GPTU_CLC_SPEN_SET(0) | ++ GPTU_CLC_DISR_SET(0); ++} ++ ++static inline void lq_disable_gptu(void) ++{ ++ struct clk *clk = clk_get_sys("1e100a00.gptu", NULL); ++ ltq_w32(0x00, LQ_GPTU_IRNEN); ++ ltq_w32(0xfff, LQ_GPTU_IRNCR); ++ ++ /* Set divider as 0, enable write protection for SPEN, disable module. */ ++ *LQ_GPTU_CLC = ++ GPTU_CLC_SMC_SET(0x00) | ++ GPTU_CLC_RMC_SET(0x00) | ++ GPTU_CLC_FSOE_SET(0) | ++ GPTU_CLC_SBWE_SET(0) | ++ GPTU_CLC_EDIS_SET(0) | ++ GPTU_CLC_SPEN_SET(0) | ++ GPTU_CLC_DISR_SET(1); ++ ++ clk_enable(clk); ++} ++ ++int lq_request_timer(unsigned int timer, unsigned int flag, ++ unsigned long value, unsigned long arg1, unsigned long arg2) ++{ ++ int ret = 0; ++ unsigned int con_reg, irnen_reg; ++ int n, X; ++ ++ if (timer >= FIRST_TIMER + timer_dev.number_of_timers) ++ return -EINVAL; ++ ++ printk(KERN_INFO "request_timer(%d, 0x%08X, %lu)...", ++ timer, flag, value); ++ ++ if (TIMER_FLAG_MASK_SIZE(flag) == TIMER_FLAG_16BIT) ++ value &= 0xFFFF; ++ else ++ timer &= ~0x01; ++ ++ mutex_lock(&timer_dev.gptu_mutex); ++ ++ /* ++ * Allocate timer. ++ */ ++ if (timer < FIRST_TIMER) { ++ unsigned int mask; ++ unsigned int shift; ++ /* This takes care of TIMER1B which is the only choice for Voice TAPI system */ ++ unsigned int offset = TIMER2A; ++ ++ /* ++ * Pick up a free timer. ++ */ ++ if (TIMER_FLAG_MASK_SIZE(flag) == TIMER_FLAG_16BIT) { ++ mask = 1 << offset; ++ shift = 1; ++ } else { ++ mask = 3 << offset; ++ shift = 2; ++ } ++ for (timer = offset; ++ timer < offset + timer_dev.number_of_timers; ++ timer += shift, mask <<= shift) ++ if (!(timer_dev.occupation & mask)) { ++ timer_dev.occupation |= mask; ++ break; ++ } ++ if (timer >= offset + timer_dev.number_of_timers) { ++ printk("failed![%d]\n", __LINE__); ++ mutex_unlock(&timer_dev.gptu_mutex); ++ return -EINVAL; ++ } else ++ ret = timer; ++ } else { ++ register unsigned int mask; ++ ++ /* ++ * Check if the requested timer is free. ++ */ ++ mask = (TIMER_FLAG_MASK_SIZE(flag) == TIMER_FLAG_16BIT ? 1 : 3) << timer; ++ if ((timer_dev.occupation & mask)) { ++ printk("failed![%d] mask %#x, timer_dev.occupation %#x\n", ++ __LINE__, mask, timer_dev.occupation); ++ mutex_unlock(&timer_dev.gptu_mutex); ++ return -EBUSY; ++ } else { ++ timer_dev.occupation |= mask; ++ ret = 0; ++ } ++ } ++ ++ /* ++ * Prepare control register value. ++ */ ++ switch (TIMER_FLAG_MASK_EDGE(flag)) { ++ default: ++ case TIMER_FLAG_NONE_EDGE: ++ con_reg = GPTU_CON_EDGE_SET(0x00); ++ break; ++ case TIMER_FLAG_RISE_EDGE: ++ con_reg = GPTU_CON_EDGE_SET(0x01); ++ break; ++ case TIMER_FLAG_FALL_EDGE: ++ con_reg = GPTU_CON_EDGE_SET(0x02); ++ break; ++ case TIMER_FLAG_ANY_EDGE: ++ con_reg = GPTU_CON_EDGE_SET(0x03); ++ break; ++ } ++ if (TIMER_FLAG_MASK_TYPE(flag) == TIMER_FLAG_TIMER) ++ con_reg |= ++ TIMER_FLAG_MASK_SRC(flag) == ++ TIMER_FLAG_EXT_SRC ? GPTU_CON_SRC_EXT_SET(1) : ++ GPTU_CON_SRC_EXT_SET(0); ++ else ++ con_reg |= ++ TIMER_FLAG_MASK_SRC(flag) == ++ TIMER_FLAG_EXT_SRC ? GPTU_CON_SRC_EG_SET(1) : ++ GPTU_CON_SRC_EG_SET(0); ++ con_reg |= ++ TIMER_FLAG_MASK_SYNC(flag) == ++ TIMER_FLAG_UNSYNC ? GPTU_CON_SYNC_SET(0) : ++ GPTU_CON_SYNC_SET(1); ++ con_reg |= ++ TIMER_FLAG_MASK_INVERT(flag) == ++ TIMER_FLAG_REAL ? GPTU_CON_INV_SET(0) : GPTU_CON_INV_SET(1); ++ con_reg |= ++ TIMER_FLAG_MASK_SIZE(flag) == ++ TIMER_FLAG_16BIT ? GPTU_CON_EXT_SET(0) : ++ GPTU_CON_EXT_SET(1); ++ con_reg |= ++ TIMER_FLAG_MASK_STOP(flag) == ++ TIMER_FLAG_ONCE ? GPTU_CON_STP_SET(1) : GPTU_CON_STP_SET(0); ++ con_reg |= ++ TIMER_FLAG_MASK_TYPE(flag) == ++ TIMER_FLAG_TIMER ? GPTU_CON_CNT_SET(0) : ++ GPTU_CON_CNT_SET(1); ++ con_reg |= ++ TIMER_FLAG_MASK_DIR(flag) == ++ TIMER_FLAG_UP ? GPTU_CON_DIR_SET(1) : GPTU_CON_DIR_SET(0); ++ ++ /* ++ * Fill up running data. ++ */ ++ timer_dev.timer[timer - FIRST_TIMER].flag = flag; ++ timer_dev.timer[timer - FIRST_TIMER].arg1 = arg1; ++ timer_dev.timer[timer - FIRST_TIMER].arg2 = arg2; ++ if (TIMER_FLAG_MASK_SIZE(flag) != TIMER_FLAG_16BIT) ++ timer_dev.timer[timer - FIRST_TIMER + 1].flag = flag; ++ ++ /* ++ * Enable GPTU module. ++ */ ++ if (!timer_dev.f_gptu_on) { ++ lq_enable_gptu(); ++ timer_dev.f_gptu_on = 1; ++ } ++ ++ /* ++ * Enable IRQ. ++ */ ++ if (TIMER_FLAG_MASK_HANDLE(flag) != TIMER_FLAG_NO_HANDLE) { ++ if (TIMER_FLAG_MASK_HANDLE(flag) == TIMER_FLAG_SIGNAL) ++ timer_dev.timer[timer - FIRST_TIMER].arg1 = ++ (unsigned long) find_task_by_vpid((int) arg1); ++ ++ irnen_reg = 1 << (timer - FIRST_TIMER); ++ ++ if (TIMER_FLAG_MASK_HANDLE(flag) == TIMER_FLAG_SIGNAL ++ || (TIMER_FLAG_MASK_HANDLE(flag) == ++ TIMER_FLAG_CALLBACK_IN_IRQ ++ && timer_dev.timer[timer - FIRST_TIMER].arg1)) { ++ enable_irq(timer_dev.timer[timer - FIRST_TIMER].irq); ++ timer_dev.timer[timer - FIRST_TIMER].f_irq_on = 1; ++ } ++ } else ++ irnen_reg = 0; ++ ++ /* ++ * Write config register, reload value and enable interrupt. ++ */ ++ n = timer >> 1; ++ X = timer & 0x01; ++ *LQ_GPTU_CON(n, X) = con_reg; ++ *LQ_GPTU_RELOAD(n, X) = value; ++ /* printk("reload value = %d\n", (u32)value); */ ++ *LQ_GPTU_IRNEN |= irnen_reg; ++ ++ mutex_unlock(&timer_dev.gptu_mutex); ++ printk("successful!\n"); ++ return ret; ++} ++EXPORT_SYMBOL(lq_request_timer); ++ ++int lq_free_timer(unsigned int timer) ++{ ++ unsigned int flag; ++ unsigned int mask; ++ int n, X; ++ ++ if (!timer_dev.f_gptu_on) ++ return -EINVAL; ++ ++ if (timer < FIRST_TIMER || timer >= FIRST_TIMER + timer_dev.number_of_timers) ++ return -EINVAL; ++ ++ mutex_lock(&timer_dev.gptu_mutex); ++ ++ flag = timer_dev.timer[timer - FIRST_TIMER].flag; ++ if (TIMER_FLAG_MASK_SIZE(flag) != TIMER_FLAG_16BIT) ++ timer &= ~0x01; ++ ++ mask = (TIMER_FLAG_MASK_SIZE(flag) == TIMER_FLAG_16BIT ? 1 : 3) << timer; ++ if (((timer_dev.occupation & mask) ^ mask)) { ++ mutex_unlock(&timer_dev.gptu_mutex); ++ return -EINVAL; ++ } ++ ++ n = timer >> 1; ++ X = timer & 0x01; ++ ++ if (GPTU_CON_EN(n, X)) ++ *LQ_GPTU_RUN(n, X) = GPTU_RUN_CEN_SET(1); ++ ++ *LQ_GPTU_IRNEN &= ~GPTU_IRNEN_TC_SET(n, X, 1); ++ *LQ_GPTU_IRNCR |= GPTU_IRNCR_TC_SET(n, X, 1); ++ ++ if (timer_dev.timer[timer - FIRST_TIMER].f_irq_on) { ++ disable_irq(timer_dev.timer[timer - FIRST_TIMER].irq); ++ timer_dev.timer[timer - FIRST_TIMER].f_irq_on = 0; ++ } ++ ++ timer_dev.occupation &= ~mask; ++ if (!timer_dev.occupation && timer_dev.f_gptu_on) { ++ lq_disable_gptu(); ++ timer_dev.f_gptu_on = 0; ++ } ++ ++ mutex_unlock(&timer_dev.gptu_mutex); ++ ++ return 0; ++} ++EXPORT_SYMBOL(lq_free_timer); ++ ++int lq_start_timer(unsigned int timer, int is_resume) ++{ ++ unsigned int flag; ++ unsigned int mask; ++ int n, X; ++ ++ if (!timer_dev.f_gptu_on) ++ return -EINVAL; ++ ++ if (timer < FIRST_TIMER || timer >= FIRST_TIMER + timer_dev.number_of_timers) ++ return -EINVAL; ++ ++ mutex_lock(&timer_dev.gptu_mutex); ++ ++ flag = timer_dev.timer[timer - FIRST_TIMER].flag; ++ if (TIMER_FLAG_MASK_SIZE(flag) != TIMER_FLAG_16BIT) ++ timer &= ~0x01; ++ ++ mask = (TIMER_FLAG_MASK_SIZE(flag) == ++ TIMER_FLAG_16BIT ? 1 : 3) << timer; ++ if (((timer_dev.occupation & mask) ^ mask)) { ++ mutex_unlock(&timer_dev.gptu_mutex); ++ return -EINVAL; ++ } ++ ++ n = timer >> 1; ++ X = timer & 0x01; ++ ++ *LQ_GPTU_RUN(n, X) = GPTU_RUN_RL_SET(!is_resume) | GPTU_RUN_SEN_SET(1); ++ ++ ++ mutex_unlock(&timer_dev.gptu_mutex); ++ ++ return 0; ++} ++EXPORT_SYMBOL(lq_start_timer); ++ ++int lq_stop_timer(unsigned int timer) ++{ ++ unsigned int flag; ++ unsigned int mask; ++ int n, X; ++ ++ if (!timer_dev.f_gptu_on) ++ return -EINVAL; ++ ++ if (timer < FIRST_TIMER ++ || timer >= FIRST_TIMER + timer_dev.number_of_timers) ++ return -EINVAL; ++ ++ mutex_lock(&timer_dev.gptu_mutex); ++ ++ flag = timer_dev.timer[timer - FIRST_TIMER].flag; ++ if (TIMER_FLAG_MASK_SIZE(flag) != TIMER_FLAG_16BIT) ++ timer &= ~0x01; ++ ++ mask = (TIMER_FLAG_MASK_SIZE(flag) == TIMER_FLAG_16BIT ? 1 : 3) << timer; ++ if (((timer_dev.occupation & mask) ^ mask)) { ++ mutex_unlock(&timer_dev.gptu_mutex); ++ return -EINVAL; ++ } ++ ++ n = timer >> 1; ++ X = timer & 0x01; ++ ++ *LQ_GPTU_RUN(n, X) = GPTU_RUN_CEN_SET(1); ++ ++ mutex_unlock(&timer_dev.gptu_mutex); ++ ++ return 0; ++} ++EXPORT_SYMBOL(lq_stop_timer); ++ ++int lq_reset_counter_flags(u32 timer, u32 flags) ++{ ++ unsigned int oflag; ++ unsigned int mask, con_reg; ++ int n, X; ++ ++ if (!timer_dev.f_gptu_on) ++ return -EINVAL; ++ ++ if (timer < FIRST_TIMER || timer >= FIRST_TIMER + timer_dev.number_of_timers) ++ return -EINVAL; ++ ++ mutex_lock(&timer_dev.gptu_mutex); ++ ++ oflag = timer_dev.timer[timer - FIRST_TIMER].flag; ++ if (TIMER_FLAG_MASK_SIZE(oflag) != TIMER_FLAG_16BIT) ++ timer &= ~0x01; ++ ++ mask = (TIMER_FLAG_MASK_SIZE(oflag) == TIMER_FLAG_16BIT ? 1 : 3) << timer; ++ if (((timer_dev.occupation & mask) ^ mask)) { ++ mutex_unlock(&timer_dev.gptu_mutex); ++ return -EINVAL; ++ } ++ ++ switch (TIMER_FLAG_MASK_EDGE(flags)) { ++ default: ++ case TIMER_FLAG_NONE_EDGE: ++ con_reg = GPTU_CON_EDGE_SET(0x00); ++ break; ++ case TIMER_FLAG_RISE_EDGE: ++ con_reg = GPTU_CON_EDGE_SET(0x01); ++ break; ++ case TIMER_FLAG_FALL_EDGE: ++ con_reg = GPTU_CON_EDGE_SET(0x02); ++ break; ++ case TIMER_FLAG_ANY_EDGE: ++ con_reg = GPTU_CON_EDGE_SET(0x03); ++ break; ++ } ++ if (TIMER_FLAG_MASK_TYPE(flags) == TIMER_FLAG_TIMER) ++ con_reg |= TIMER_FLAG_MASK_SRC(flags) == TIMER_FLAG_EXT_SRC ? GPTU_CON_SRC_EXT_SET(1) : GPTU_CON_SRC_EXT_SET(0); ++ else ++ con_reg |= TIMER_FLAG_MASK_SRC(flags) == TIMER_FLAG_EXT_SRC ? GPTU_CON_SRC_EG_SET(1) : GPTU_CON_SRC_EG_SET(0); ++ con_reg |= TIMER_FLAG_MASK_SYNC(flags) == TIMER_FLAG_UNSYNC ? GPTU_CON_SYNC_SET(0) : GPTU_CON_SYNC_SET(1); ++ con_reg |= TIMER_FLAG_MASK_INVERT(flags) == TIMER_FLAG_REAL ? GPTU_CON_INV_SET(0) : GPTU_CON_INV_SET(1); ++ con_reg |= TIMER_FLAG_MASK_SIZE(flags) == TIMER_FLAG_16BIT ? GPTU_CON_EXT_SET(0) : GPTU_CON_EXT_SET(1); ++ con_reg |= TIMER_FLAG_MASK_STOP(flags) == TIMER_FLAG_ONCE ? GPTU_CON_STP_SET(1) : GPTU_CON_STP_SET(0); ++ con_reg |= TIMER_FLAG_MASK_TYPE(flags) == TIMER_FLAG_TIMER ? GPTU_CON_CNT_SET(0) : GPTU_CON_CNT_SET(1); ++ con_reg |= TIMER_FLAG_MASK_DIR(flags) == TIMER_FLAG_UP ? GPTU_CON_DIR_SET(1) : GPTU_CON_DIR_SET(0); ++ ++ timer_dev.timer[timer - FIRST_TIMER].flag = flags; ++ if (TIMER_FLAG_MASK_SIZE(flags) != TIMER_FLAG_16BIT) ++ timer_dev.timer[timer - FIRST_TIMER + 1].flag = flags; ++ ++ n = timer >> 1; ++ X = timer & 0x01; ++ ++ *LQ_GPTU_CON(n, X) = con_reg; ++ smp_wmb(); ++ mutex_unlock(&timer_dev.gptu_mutex); ++ return 0; ++} ++EXPORT_SYMBOL(lq_reset_counter_flags); ++ ++int lq_get_count_value(unsigned int timer, unsigned long *value) ++{ ++ unsigned int flag; ++ unsigned int mask; ++ int n, X; ++ ++ if (!timer_dev.f_gptu_on) ++ return -EINVAL; ++ ++ if (timer < FIRST_TIMER ++ || timer >= FIRST_TIMER + timer_dev.number_of_timers) ++ return -EINVAL; ++ ++ mutex_lock(&timer_dev.gptu_mutex); ++ ++ flag = timer_dev.timer[timer - FIRST_TIMER].flag; ++ if (TIMER_FLAG_MASK_SIZE(flag) != TIMER_FLAG_16BIT) ++ timer &= ~0x01; ++ ++ mask = (TIMER_FLAG_MASK_SIZE(flag) == TIMER_FLAG_16BIT ? 1 : 3) << timer; ++ if (((timer_dev.occupation & mask) ^ mask)) { ++ mutex_unlock(&timer_dev.gptu_mutex); ++ return -EINVAL; ++ } ++ ++ n = timer >> 1; ++ X = timer & 0x01; ++ ++ *value = *LQ_GPTU_COUNT(n, X); ++ ++ ++ mutex_unlock(&timer_dev.gptu_mutex); ++ ++ return 0; ++} ++EXPORT_SYMBOL(lq_get_count_value); ++ ++u32 lq_cal_divider(unsigned long freq) ++{ ++ u64 module_freq, fpi = ltq_get_fpi_bus_clock(2); ++ u32 clock_divider = 1; ++ module_freq = fpi * 1000; ++ do_div(module_freq, clock_divider * freq); ++ return module_freq; ++} ++EXPORT_SYMBOL(lq_cal_divider); ++ ++int lq_set_timer(unsigned int timer, unsigned int freq, int is_cyclic, ++ int is_ext_src, unsigned int handle_flag, unsigned long arg1, ++ unsigned long arg2) ++{ ++ unsigned long divider; ++ unsigned int flag; ++ ++ divider = lq_cal_divider(freq); ++ if (divider == 0) ++ return -EINVAL; ++ flag = ((divider & ~0xFFFF) ? TIMER_FLAG_32BIT : TIMER_FLAG_16BIT) ++ | (is_cyclic ? TIMER_FLAG_CYCLIC : TIMER_FLAG_ONCE) ++ | (is_ext_src ? TIMER_FLAG_EXT_SRC : TIMER_FLAG_INT_SRC) ++ | TIMER_FLAG_TIMER | TIMER_FLAG_DOWN ++ | TIMER_FLAG_MASK_HANDLE(handle_flag); ++ ++ printk(KERN_INFO "lq_set_timer(%d, %d), divider = %lu\n", ++ timer, freq, divider); ++ return lq_request_timer(timer, flag, divider, arg1, arg2); ++} ++EXPORT_SYMBOL(lq_set_timer); ++ ++int lq_set_counter(unsigned int timer, unsigned int flag, u32 reload, ++ unsigned long arg1, unsigned long arg2) ++{ ++ printk(KERN_INFO "lq_set_counter(%d, %#x, %d)\n", timer, flag, reload); ++ return lq_request_timer(timer, flag, reload, arg1, arg2); ++} ++EXPORT_SYMBOL(lq_set_counter); ++ ++static long gptu_ioctl(struct file *file, unsigned int cmd, ++ unsigned long arg) ++{ ++ int ret; ++ struct gptu_ioctl_param param; ++ ++ if (!access_ok(VERIFY_READ, (void __user *)arg, sizeof(struct gptu_ioctl_param))) ++ return -EFAULT; ++ copy_from_user(¶m, (void __user *)arg, sizeof(param)); ++ ++ if ((((cmd == GPTU_REQUEST_TIMER || cmd == GPTU_SET_TIMER ++ || GPTU_SET_COUNTER) && param.timer < 2) ++ || cmd == GPTU_GET_COUNT_VALUE || cmd == GPTU_CALCULATE_DIVIDER) ++ && !access_ok(VERIFY_WRITE, (void __user *)arg, ++ sizeof(struct gptu_ioctl_param))) ++ return -EFAULT; ++ ++ switch (cmd) { ++ case GPTU_REQUEST_TIMER: ++ ret = lq_request_timer(param.timer, param.flag, param.value, ++ (unsigned long) param.pid, ++ (unsigned long) param.sig); ++ if (ret > 0) { ++ copy_to_user(&((struct gptu_ioctl_param *) arg)-> ++ timer, &ret, sizeof(&ret)); ++ ret = 0; ++ } ++ break; ++ case GPTU_FREE_TIMER: ++ ret = lq_free_timer(param.timer); ++ break; ++ case GPTU_START_TIMER: ++ ret = lq_start_timer(param.timer, param.flag); ++ break; ++ case GPTU_STOP_TIMER: ++ ret = lq_stop_timer(param.timer); ++ break; ++ case GPTU_GET_COUNT_VALUE: ++ ret = lq_get_count_value(param.timer, ¶m.value); ++ if (!ret) ++ copy_to_user(&((struct gptu_ioctl_param *) arg)-> ++ value, ¶m.value, ++ sizeof(param.value)); ++ break; ++ case GPTU_CALCULATE_DIVIDER: ++ param.value = lq_cal_divider(param.value); ++ if (param.value == 0) ++ ret = -EINVAL; ++ else { ++ copy_to_user(&((struct gptu_ioctl_param *) arg)-> ++ value, ¶m.value, ++ sizeof(param.value)); ++ ret = 0; ++ } ++ break; ++ case GPTU_SET_TIMER: ++ ret = lq_set_timer(param.timer, param.value, ++ TIMER_FLAG_MASK_STOP(param.flag) != ++ TIMER_FLAG_ONCE ? 1 : 0, ++ TIMER_FLAG_MASK_SRC(param.flag) == ++ TIMER_FLAG_EXT_SRC ? 1 : 0, ++ TIMER_FLAG_MASK_HANDLE(param.flag) == ++ TIMER_FLAG_SIGNAL ? TIMER_FLAG_SIGNAL : ++ TIMER_FLAG_NO_HANDLE, ++ (unsigned long) param.pid, ++ (unsigned long) param.sig); ++ if (ret > 0) { ++ copy_to_user(&((struct gptu_ioctl_param *) arg)-> ++ timer, &ret, sizeof(&ret)); ++ ret = 0; ++ } ++ break; ++ case GPTU_SET_COUNTER: ++ lq_set_counter(param.timer, param.flag, param.value, 0, 0); ++ if (ret > 0) { ++ copy_to_user(&((struct gptu_ioctl_param *) arg)-> ++ timer, &ret, sizeof(&ret)); ++ ret = 0; ++ } ++ break; ++ default: ++ ret = -ENOTTY; ++ } ++ ++ return ret; ++} ++ ++static int gptu_open(struct inode *inode, struct file *file) ++{ ++ return 0; ++} ++ ++static int gptu_release(struct inode *inode, struct file *file) ++{ ++ return 0; ++} ++ ++int __init lq_gptu_init(void) ++{ ++ int ret; ++ unsigned int i; ++ ++ ltq_w32(0, LQ_GPTU_IRNEN); ++ ltq_w32(0xfff, LQ_GPTU_IRNCR); ++ ++ memset(&timer_dev, 0, sizeof(timer_dev)); ++ mutex_init(&timer_dev.gptu_mutex); ++ ++ lq_enable_gptu(); ++ timer_dev.number_of_timers = GPTU_ID_CFG * 2; ++ lq_disable_gptu(); ++ if (timer_dev.number_of_timers > MAX_NUM_OF_32BIT_TIMER_BLOCKS * 2) ++ timer_dev.number_of_timers = MAX_NUM_OF_32BIT_TIMER_BLOCKS * 2; ++ printk(KERN_INFO "gptu: totally %d 16-bit timers/counters\n", timer_dev.number_of_timers); ++ ++ ret = misc_register(&gptu_miscdev); ++ if (ret) { ++ printk(KERN_ERR "gptu: can't misc_register, get error %d\n", -ret); ++ return ret; ++ } else { ++ printk(KERN_INFO "gptu: misc_register on minor %d\n", gptu_miscdev.minor); ++ } ++ ++ for (i = 0; i < timer_dev.number_of_timers; i++) { ++ ret = request_irq(TIMER_INTERRUPT + i, timer_irq_handler, IRQF_TIMER, gptu_miscdev.name, &timer_dev.timer[i]); ++ if (ret) { ++ for (; i >= 0; i--) ++ free_irq(TIMER_INTERRUPT + i, &timer_dev.timer[i]); ++ misc_deregister(&gptu_miscdev); ++ printk(KERN_ERR "gptu: failed in requesting irq (%d), get error %d\n", i, -ret); ++ return ret; ++ } else { ++ timer_dev.timer[i].irq = TIMER_INTERRUPT + i; ++ disable_irq(timer_dev.timer[i].irq); ++ printk(KERN_INFO "gptu: succeeded to request irq %d\n", timer_dev.timer[i].irq); ++ } ++ } ++ ++ return 0; ++} ++ ++void __exit lq_gptu_exit(void) ++{ ++ unsigned int i; ++ ++ for (i = 0; i < timer_dev.number_of_timers; i++) { ++ if (timer_dev.timer[i].f_irq_on) ++ disable_irq(timer_dev.timer[i].irq); ++ free_irq(timer_dev.timer[i].irq, &timer_dev.timer[i]); ++ } ++ lq_disable_gptu(); ++ misc_deregister(&gptu_miscdev); ++} ++ ++module_init(lq_gptu_init); ++module_exit(lq_gptu_exit); ++ ++#endif diff --git a/target/linux/lantiq/patches-4.19/0018-MTD-nand-lots-of-xrx200-fixes.patch b/target/linux/lantiq/patches-4.19/0018-MTD-nand-lots-of-xrx200-fixes.patch new file mode 100644 index 0000000000..b97967d20e --- /dev/null +++ b/target/linux/lantiq/patches-4.19/0018-MTD-nand-lots-of-xrx200-fixes.patch @@ -0,0 +1,122 @@ +From 997a8965db8417266bea3fbdcfa3e5655a1b52fa Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Tue, 9 Sep 2014 23:12:15 +0200 +Subject: [PATCH 18/36] MTD: nand: lots of xrx200 fixes + +Signed-off-by: John Crispin +--- + drivers/mtd/nand/xway_nand.c | 63 ++++++++++++++++++++++++++++++++++++++++++ + 1 file changed, 63 insertions(+) + +--- a/drivers/mtd/nand/xway_nand.c ++++ b/drivers/mtd/nand/xway_nand.c +@@ -63,6 +63,24 @@ + #define NAND_CON_CSMUX (1 << 1) + #define NAND_CON_NANDM 1 + ++#define DANUBE_PCI_REG32( addr ) (*(volatile u32 *)(addr)) ++#define PCI_CR_PR_OFFSET (KSEG1+0x1E105400) ++#define PCI_CR_PC_ARB (PCI_CR_PR_OFFSET + 0x0080) ++ ++/* ++ * req_mask provides a mechanism to prevent interference between ++ * nand and pci (probably only relevant for the BT Home Hub 2B). ++ * Setting it causes the corresponding pci req pins to be masked ++ * during nand access, and also moves ebu locking from the read/write ++ * functions to the chip select function to ensure that the whole ++ * operation runs with interrupts disabled. ++ * In addition it switches on some extra waiting in xway_cmd_ctrl(). ++ * This seems to be necessary if the ebu_cs1 pin has open-drain disabled, ++ * which in turn seems to be necessary for the nor chip to be recognised ++ * reliably, on a board (Home Hub 2B again) which has both nor and nand. ++ */ ++static __be32 req_mask = 0; ++ + struct xway_nand_data { + struct nand_chip chip; + unsigned long csflags; +@@ -94,10 +112,22 @@ static void xway_select_chip(struct mtd_ + case -1: + ltq_ebu_w32_mask(NAND_CON_CE, 0, EBU_NAND_CON); + ltq_ebu_w32_mask(NAND_CON_NANDM, 0, EBU_NAND_CON); ++ ++ if (req_mask) { ++ /* Unmask all external PCI request */ ++ DANUBE_PCI_REG32(PCI_CR_PC_ARB) &= ~(req_mask << 16); ++ } ++ + spin_unlock_irqrestore(&ebu_lock, data->csflags); + break; + case 0: + spin_lock_irqsave(&ebu_lock, data->csflags); ++ ++ if (req_mask) { ++ /* Mask all external PCI request */ ++ DANUBE_PCI_REG32(PCI_CR_PC_ARB) |= (req_mask << 16); ++ } ++ + ltq_ebu_w32_mask(0, NAND_CON_NANDM, EBU_NAND_CON); + ltq_ebu_w32_mask(0, NAND_CON_CE, EBU_NAND_CON); + break; +@@ -108,6 +138,12 @@ static void xway_select_chip(struct mtd_ + + static void xway_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl) + { ++ ++ if (req_mask) { ++ if (cmd != NAND_CMD_STATUS) ++ ltq_ebu_w32(0, EBU_NAND_WAIT); /* Clear nand ready */ ++ } ++ + if (cmd == NAND_CMD_NONE) + return; + +@@ -118,6 +154,24 @@ static void xway_cmd_ctrl(struct mtd_inf + + while ((ltq_ebu_r32(EBU_NAND_WAIT) & NAND_WAIT_WR_C) == 0) + ; ++ ++ if (req_mask) { ++ /* ++ * program and erase have their own busy handlers ++ * status and sequential in needs no delay ++ */ ++ switch (cmd) { ++ case NAND_CMD_ERASE1: ++ case NAND_CMD_SEQIN: ++ case NAND_CMD_STATUS: ++ case NAND_CMD_READID: ++ return; ++ } ++ ++ /* wait until command is processed */ ++ while ((ltq_ebu_r32(EBU_NAND_WAIT) & NAND_WAIT_RD) == 0) ++ ; ++ } + } + + static int xway_dev_ready(struct mtd_info *mtd) +@@ -157,6 +211,7 @@ static int xway_nand_probe(struct platfo + int err; + u32 cs; + u32 cs_flag = 0; ++ const __be32 *req_mask_ptr; + + /* Allocate memory for the device structure (and zero it) */ + data = devm_kzalloc(&pdev->dev, sizeof(struct xway_nand_data), +@@ -192,6 +247,15 @@ static int xway_nand_probe(struct platfo + if (!err && cs == 1) + cs_flag = NAND_CON_IN_CS1 | NAND_CON_OUT_CS1; + ++ req_mask_ptr = of_get_property(pdev->dev.of_node, ++ "req-mask", NULL); ++ ++ /* ++ * Load the PCI req lines to mask from the device tree. If the ++ * property is not present, setting req_mask to 0 disables masking. ++ */ ++ req_mask = (req_mask_ptr ? *req_mask_ptr : 0); ++ + /* setup the EBU to run in NAND mode on our base addr */ + ltq_ebu_w32(CPHYSADDR(data->nandaddr) + | ADDSEL1_MASK(3) | ADDSEL1_REGEN, EBU_ADDSEL1); diff --git a/target/linux/lantiq/patches-4.19/0020-MTD-lantiq-handle-NO_XIP-on-cfi0001-flash.patch b/target/linux/lantiq/patches-4.19/0020-MTD-lantiq-handle-NO_XIP-on-cfi0001-flash.patch new file mode 100644 index 0000000000..502c5af9f2 --- /dev/null +++ b/target/linux/lantiq/patches-4.19/0020-MTD-lantiq-handle-NO_XIP-on-cfi0001-flash.patch @@ -0,0 +1,25 @@ +From e3b20f04e9f9cae1babe091fdc1d08d7703ae344 Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Thu, 7 Aug 2014 18:18:00 +0200 +Subject: [PATCH 20/36] MTD: lantiq: handle NO_XIP on cfi0001 flash + +Signed-off-by: John Crispin +--- + drivers/mtd/maps/lantiq-flash.c | 6 +++++- + 1 file changed, 5 insertions(+), 1 deletion(-) + +--- a/drivers/mtd/maps/lantiq-flash.c ++++ b/drivers/mtd/maps/lantiq-flash.c +@@ -131,7 +131,11 @@ ltq_mtd_probe(struct platform_device *pd + if (!ltq_mtd->map) + return -ENOMEM; + +- ltq_mtd->map->phys = ltq_mtd->res->start; ++ if (of_find_property(pdev->dev.of_node, "lantiq,noxip", NULL)) ++ ltq_mtd->map->phys = NO_XIP; ++ else ++ ltq_mtd->map->phys = ltq_mtd->res->start; ++ ltq_mtd->res->start; + ltq_mtd->map->size = resource_size(ltq_mtd->res); + ltq_mtd->map->virt = devm_ioremap_resource(&pdev->dev, ltq_mtd->res); + if (IS_ERR(ltq_mtd->map->virt)) diff --git a/target/linux/lantiq/patches-4.19/0022-MTD-m25p80-allow-loading-mtd-name-from-OF.patch b/target/linux/lantiq/patches-4.19/0022-MTD-m25p80-allow-loading-mtd-name-from-OF.patch new file mode 100644 index 0000000000..415c8579bd --- /dev/null +++ b/target/linux/lantiq/patches-4.19/0022-MTD-m25p80-allow-loading-mtd-name-from-OF.patch @@ -0,0 +1,44 @@ +From 4400e1f593ea40a51912128adb4f53d59e62cad8 Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Wed, 10 Sep 2014 22:40:18 +0200 +Subject: [PATCH 22/36] MTD: m25p80: allow loading mtd name from OF + +In accordance with the physmap flash we should honour the linux,mtd-name +property when deciding what name the mtd device has. + +Signed-off-by: Thomas Langer +Signed-off-by: John Crispin +--- + drivers/mtd/devices/m25p80.c | 6 ++++++ + 1 file changed, 6 insertions(+) + +--- a/drivers/mtd/devices/m25p80.c ++++ b/drivers/mtd/devices/m25p80.c +@@ -19,6 +19,7 @@ + #include + #include + #include ++#include + + #include + #include +@@ -245,6 +246,10 @@ static int m25p_probe(struct spi_device + }; + char *flash_name; + int ret; ++ const char __maybe_unused *of_mtd_name = NULL; ++ ++ of_property_read_string(spi->dev.of_node, ++ "linux,mtd-name", &of_mtd_name); + + data = dev_get_platdata(&spi->dev); + +@@ -283,6 +288,8 @@ static int m25p_probe(struct spi_device + + if (data && data->name) + nor->mtd.name = data->name; ++ else if (of_mtd_name) ++ nor->mtd.name = of_mtd_name; + + /* For some (historical?) reason many platforms provide two different + * names in flash_platform_data: "name" and "type". Quite often name is diff --git a/target/linux/lantiq/patches-4.19/0023-NET-PHY-add-led-support-for-intel-xway.patch b/target/linux/lantiq/patches-4.19/0023-NET-PHY-add-led-support-for-intel-xway.patch new file mode 100644 index 0000000000..0686842821 --- /dev/null +++ b/target/linux/lantiq/patches-4.19/0023-NET-PHY-add-led-support-for-intel-xway.patch @@ -0,0 +1,294 @@ +From 0a63ab263725c427051a8bbaa0732b749627da27 Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Thu, 7 Aug 2014 18:15:36 +0200 +Subject: [PATCH 23/36] NET: PHY: adds driver for lantiq PHY11G + +Signed-off-by: John Crispin +--- + drivers/net/phy/Kconfig | 5 + + drivers/net/phy/Makefile | 1 + + drivers/net/phy/lantiq.c | 231 ++++++++++++++++++++++++++++++++++++++++++++++ + 3 files changed, 237 insertions(+) + create mode 100644 drivers/net/phy/lantiq.c + +--- a/drivers/net/phy/intel-xway.c ++++ b/drivers/net/phy/intel-xway.c +@@ -152,6 +152,51 @@ + #define PHY_ID_PHY11G_VR9 0xD565A409 + #define PHY_ID_PHY22F_VR9 0xD565A419 + ++#if IS_ENABLED(CONFIG_OF_MDIO) ++static int vr9_gphy_of_reg_init(struct phy_device *phydev) ++{ ++ u32 tmp; ++ ++ /* store the led values if one was passed by the devicetree */ ++ if (!of_property_read_u32(phydev->mdio.dev.of_node, "lantiq,ledch", &tmp)) ++ phy_write_mmd(phydev, MDIO_MMD_VEND2, XWAY_MMD_LEDCH, tmp); ++ ++ if (!of_property_read_u32(phydev->mdio.dev.of_node, "lantiq,ledcl", &tmp)) ++ phy_write_mmd(phydev, MDIO_MMD_VEND2, XWAY_MMD_LEDCL, tmp); ++ ++ if (!of_property_read_u32(phydev->mdio.dev.of_node, "lantiq,led0h", &tmp)) ++ phy_write_mmd(phydev, MDIO_MMD_VEND2, XWAY_MMD_LED0H, tmp); ++ ++ if (!of_property_read_u32(phydev->mdio.dev.of_node, "lantiq,led0l", &tmp)) ++ phy_write_mmd(phydev, MDIO_MMD_VEND2, XWAY_MMD_LED0L, tmp); ++ ++ if (!of_property_read_u32(phydev->mdio.dev.of_node, "lantiq,led1h", &tmp)) ++ phy_write_mmd(phydev, MDIO_MMD_VEND2, XWAY_MMD_LED1H, tmp); ++ ++ if (!of_property_read_u32(phydev->mdio.dev.of_node, "lantiq,led1l", &tmp)) ++ phy_write_mmd(phydev, MDIO_MMD_VEND2, XWAY_MMD_LED1L, tmp); ++ ++ if (!of_property_read_u32(phydev->mdio.dev.of_node, "lantiq,led2h", &tmp)) ++ phy_write_mmd(phydev, MDIO_MMD_VEND2, XWAY_MMD_LED3H, tmp); ++ ++ if (!of_property_read_u32(phydev->mdio.dev.of_node, "lantiq,led2l", &tmp)) ++ phy_write_mmd(phydev, MDIO_MMD_VEND2, XWAY_MMD_LED3L, tmp); ++ ++ if (!of_property_read_u32(phydev->mdio.dev.of_node, "lantiq,led3h", &tmp)) ++ phy_write_mmd(phydev, MDIO_MMD_VEND2, XWAY_MMD_LED3H, tmp); ++ ++ if (!of_property_read_u32(phydev->mdio.dev.of_node, "lantiq,led3l", &tmp)) ++ phy_write_mmd(phydev, MDIO_MMD_VEND2, XWAY_MMD_LED3L, tmp); ++ ++ return 0; ++} ++#else ++static int vr9_gphy_of_reg_init(struct phy_device *phydev) ++{ ++ return 0; ++} ++#endif /* CONFIG_OF_MDIO */ ++ + static int xway_gphy_config_init(struct phy_device *phydev) + { + int err; +@@ -190,6 +235,7 @@ static int xway_gphy_config_init(struct + phy_write_mmd(phydev, MDIO_MMD_VEND2, XWAY_MMD_LED2H, ledxh); + phy_write_mmd(phydev, MDIO_MMD_VEND2, XWAY_MMD_LED2L, ledxl); + ++ vr9_gphy_of_reg_init(phydev); + return 0; + } + +--- /dev/null ++++ b/Documentation/devicetree/bindings/phy/phy-lanitq.txt +@@ -0,0 +1,216 @@ ++Lanitq PHY binding ++============================================ ++ ++This devicetree binding controls the lantiq ethernet phys led functionality. ++ ++Example: ++ mdio@0 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ compatible = "lantiq,xrx200-mdio"; ++ phy5: ethernet-phy@5 { ++ reg = <0x1>; ++ compatible = "lantiq,phy11g", "ethernet-phy-ieee802.3-c22"; ++ }; ++ phy11: ethernet-phy@11 { ++ reg = <0x11>; ++ compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; ++ lantiq,led2h = <0x00>; ++ lantiq,led2l = <0x03>; ++ }; ++ phy12: ethernet-phy@12 { ++ reg = <0x12>; ++ compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; ++ lantiq,led1h = <0x00>; ++ lantiq,led1l = <0x03>; ++ }; ++ phy13: ethernet-phy@13 { ++ reg = <0x13>; ++ compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; ++ lantiq,led2h = <0x00>; ++ lantiq,led2l = <0x03>; ++ }; ++ phy14: ethernet-phy@14 { ++ reg = <0x14>; ++ compatible = "lantiq,phy22f", "ethernet-phy-ieee802.3-c22"; ++ lantiq,led1h = <0x00>; ++ lantiq,led1l = <0x03>; ++ }; ++ }; ++ ++Register Description ++============================================ ++ ++LEDCH: ++ ++Name Hardware Reset Value ++LEDCH 0x00C5 ++ ++| 15 | | | | | | | 8 | ++========================================= ++| RES | ++========================================= ++ ++| 7 | | | | | | | 0 | ++========================================= ++| FBF | SBF |RES | NACS | ++========================================= ++ ++Field Bits Type Description ++FBF 7:6 RW Fast Blink Frequency ++ --- ++ 0x0 (00b) F02HZ 2 Hz blinking frequency ++ 0x1 (01b) F04HZ 4 Hz blinking frequency ++ 0x2 (10b) F08HZ 8 Hz blinking frequency ++ 0x3 (11b) F16HZ 16 Hz blinking frequency ++ ++SBF 5:4 RW Slow Blink Frequency ++ --- ++ 0x0 (00b) F02HZ 2 Hz blinking frequency ++ 0x1 (01b) F04HZ 4 Hz blinking frequency ++ 0x2 (10b) F08HZ 8 Hz blinking frequency ++ 0x3 (11b) F16HZ 16 Hz blinking frequency ++ ++NACS 2:0 RW Inverse of Scan Function ++ --- ++ 0x0 (000b) NONE No Function ++ 0x1 (001b) LINK Complex function enabled when link is up ++ 0x2 (010b) PDOWN Complex function enabled when device is powered-down ++ 0x3 (011b) EEE Complex function enabled when device is in EEE mode ++ 0x4 (100b) ANEG Complex function enabled when auto-negotiation is running ++ 0x5 (101b) ABIST Complex function enabled when analog self-test is running ++ 0x6 (110b) CDIAG Complex function enabled when cable diagnostics are running ++ 0x7 (111b) TEST Complex function enabled when test mode is running ++ ++LEDCL: ++ ++Name Hardware Reset Value ++LEDCL 0x0067 ++ ++| 15 | | | | | | | 8 | ++========================================= ++| RES | ++========================================= ++ ++| 7 | | | | | | | 0 | ++========================================= ++|RES | SCAN |RES | CBLINK | ++========================================= ++ ++Field Bits Type Description ++SCAN 6:4 RW Complex Scan Configuration ++ --- ++ 000 B NONE No Function ++ 001 B LINK Complex function enabled when link is up ++ 010 B PDOWN Complex function enabled when device is powered-down ++ 011 B EEE Complex function enabled when device is in EEE mode ++ 100 B ANEG Complex function enabled when auto-negotiation is running ++ 101 B ABIST Complex function enabled when analog self-test is running ++ 110 B CDIAG Complex function enabled when cable diagnostics are running ++ 111 B TEST Complex function enabled when test mode is running ++ ++CBLINK 2:0 RW Complex Blinking Configuration ++ --- ++ 000 B NONE No Function ++ 001 B LINK Complex function enabled when link is up ++ 010 B PDOWN Complex function enabled when device is powered-down ++ 011 B EEE Complex function enabled when device is in EEE mode ++ 100 B ANEG Complex function enabled when auto-negotiation is running ++ 101 B ABIST Complex function enabled when analog self-test is running ++ 110 B CDIAG Complex function enabled when cable diagnostics are running ++ 111 B TEST Complex function enabled when test mode is running ++ ++LEDxH: ++ ++Name Hardware Reset Value ++LED0H 0x0070 ++LED1H 0x0020 ++LED2H 0x0040 ++LED3H 0x0040 ++ ++| 15 | | | | | | | 8 | ++========================================= ++| RES | ++========================================= ++ ++| 7 | | | | | | | 0 | ++========================================= ++| CON | BLINKF | ++========================================= ++ ++Field Bits Type Description ++CON 7:4 RW Constant On Configuration ++ --- ++ 0x0 (0000b) NONE LED does not light up constantly ++ 0x1 (0001b) LINK10 LED is on when link is 10 Mbit/s ++ 0x2 (0010b) LINK100 LED is on when link is 100 Mbit/s ++ 0x3 (0011b) LINK10X LED is on when link is 10/100 Mbit/s ++ 0x4 (0100b) LINK1000 LED is on when link is 1000 Mbit/s ++ 0x5 (0101b) LINK10_0 LED is on when link is 10/1000 Mbit/s ++ 0x6 (0110b) LINK100X LED is on when link is 100/1000 Mbit/s ++ 0x7 (0111b) LINK10XX LED is on when link is 10/100/1000 Mbit/s ++ 0x8 (1000b) PDOWN LED is on when device is powered-down ++ 0x9 (1001b) EEE LED is on when device is in EEE mode ++ 0xA (1010b) ANEG LED is on when auto-negotiation is running ++ 0xB (1011b) ABIST LED is on when analog self-test is running ++ 0xC (1100b) CDIAG LED is on when cable diagnostics are running ++ ++BLINKF 3:0 RW Fast Blinking Configuration ++ --- ++ 0x0 (0000b) NONE No Blinking ++ 0x1 (0001b) LINK10 Blink when link is 10 Mbit/s ++ 0x2 (0010b) LINK100 Blink when link is 100 Mbit/s ++ 0x3 (0011b) LINK10X Blink when link is 10/100 Mbit/s ++ 0x4 (0100b) LINK1000 Blink when link is 1000 Mbit/s ++ 0x5 (0101b) LINK10_0 Blink when link is 10/1000 Mbit/s ++ 0x6 (0110b) LINK100X Blink when link is 100/1000 Mbit/s ++ 0x7 (0111b) LINK10XX Blink when link is 10/100/1000 Mbit/s ++ 0x8 (1000b) PDOWN Blink when device is powered-down ++ 0x9 (1001b) EEE Blink when device is in EEE mode ++ 0xA (1010b) ANEG Blink when auto-negotiation is running ++ 0xB (1011b) ABIST Blink when analog self-test is running ++ 0xC (1100b) CDIAG Blink when cable diagnostics are running ++ ++LEDxL: ++ ++Name Hardware Reset Value ++LED0L 0x0003 ++LED1L 0x0000 ++LED2L 0x0000 ++LED3L 0x0020 ++ ++| 15 | | | | | | | 8 | ++========================================= ++| RES | ++========================================= ++ ++| 7 | | | | | | | 0 | ++========================================= ++| BLINKS | PULSE | ++========================================= ++ ++Field Bits Type Description ++BLINKS 7:4 RW Slow Blinkin Configuration ++ --- ++ 0x0 (0000b) NONE No Blinking ++ 0x1 (0001b) LINK10 Blink when link is 10 Mbit/s ++ 0x2 (0010b) LINK100 Blink when link is 100 Mbit/s ++ 0x3 (0011b) LINK10X Blink when link is 10/100 Mbit/s ++ 0x4 (0100b) LINK1000 Blink when link is 1000 Mbit/s ++ 0x5 (0101b) LINK10_0 Blink when link is 10/1000 Mbit/s ++ 0x6 (0110b) LINK100X Blink when link is 100/1000 Mbit/s ++ 0x7 (0111b) LINK10XX Blink when link is 10/100/1000 Mbit/s ++ 0x8 (1000b) PDOWN Blink when device is powered-down ++ 0x9 (1001b) EEE Blink when device is in EEE mode ++ 0xA (1010b) ANEG Blink when auto-negotiation is running ++ 0xB (1011b) ABIST Blink when analog self-test is running ++ 0xC (1100b) CDIAG Blink when cable diagnostics are runningning ++ ++PULSE 3:0 RW Pulsing Configuration ++ The pulse field is a mask field by which certain events can be combined ++ --- ++ 0x0 (0000b) NONE No pulsing ++ 0x1 (0001b) TXACT Transmit activity ++ 0x2 (0010b) RXACT Receive activity ++ 0x4 (0100b) COL Collision ++ 0x8 (1000b) RES Reserved diff --git a/target/linux/lantiq/patches-4.19/0024-MIPS-lantiq-autoselect-soc-rev-matching-fw.patch b/target/linux/lantiq/patches-4.19/0024-MIPS-lantiq-autoselect-soc-rev-matching-fw.patch new file mode 100644 index 0000000000..7fbd97feca --- /dev/null +++ b/target/linux/lantiq/patches-4.19/0024-MIPS-lantiq-autoselect-soc-rev-matching-fw.patch @@ -0,0 +1,45 @@ +From ae0c287060749dc72c866484d12bd3cade8c517d Mon Sep 17 00:00:00 2001 +From: Mathias Kresin +Date: Fri, 19 Jan 2018 20:19:06 +0100 +Subject: [PATCH] MIPS: lantiq: autoselect matching vr9 rev gphy firmware + +Add a custom xrx200 ethernet phy compatible to load the firmware matching +the vr9 revision without specifing an expected revision. + +We have quite a few boards in the tree were later produced ones are using +a more recent vr9. It is impossible to distinguish which revision of the +vr9 is used without opening the case and removing a heatsink for some of +them. + +Signed-off-by: Mathias Kresin +--- + drivers/soc/lantiq/gphy.c | 11 +++++++++++ + 1 file changed, 11 insertions(+) + +--- a/drivers/soc/lantiq/gphy.c ++++ b/drivers/soc/lantiq/gphy.c +@@ -55,6 +55,7 @@ static const struct xway_gphy_match_data + }; + + static const struct of_device_id xway_gphy_match[] = { ++ { .compatible = "lantiq,xrx200-gphy", .data = NULL }, + { .compatible = "lantiq,xrx200a1x-gphy", .data = &xrx200a1x_gphy_data }, + { .compatible = "lantiq,xrx200a2x-gphy", .data = &xrx200a2x_gphy_data }, + { .compatible = "lantiq,xrx300-gphy", .data = &xrx300_gphy_data }, +@@ -111,6 +112,16 @@ static int xway_gphy_of_probe(struct pla + + gphy_fw_name_cfg = of_device_get_match_data(dev); + ++ if (of_device_is_compatible(pdev->dev.of_node, "lantiq,xrx200-gphy")) ++ switch (ltq_soc_type()) { ++ case SOC_TYPE_VR9: ++ gphy_fw_name_cfg = &xrx200a1x_gphy_data; ++ break; ++ case SOC_TYPE_VR9_2: ++ gphy_fw_name_cfg = &xrx200a2x_gphy_data; ++ break; ++ } ++ + priv->gphy_clk_gate = devm_clk_get(dev, NULL); + if (IS_ERR(priv->gphy_clk_gate)) { + dev_err(dev, "Failed to lookup gate clock\n"); diff --git a/target/linux/lantiq/patches-4.19/0025-NET-MIPS-lantiq-adds-xrx200-net.patch b/target/linux/lantiq/patches-4.19/0025-NET-MIPS-lantiq-adds-xrx200-net.patch new file mode 100644 index 0000000000..7eaf0b7b7b --- /dev/null +++ b/target/linux/lantiq/patches-4.19/0025-NET-MIPS-lantiq-adds-xrx200-net.patch @@ -0,0 +1,3430 @@ +From fb0c9601f4414c39ff68e26b88681bef0bb04954 Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Mon, 22 Oct 2012 12:22:23 +0200 +Subject: [PATCH 25/36] NET: MIPS: lantiq: adds xrx200-net + +--- + drivers/net/ethernet/Kconfig | 8 +- + drivers/net/ethernet/Makefile | 1 + + drivers/net/ethernet/lantiq_pce.h | 163 +++ + drivers/net/ethernet/lantiq_xrx200.c | 1798 +++++++++++++++++++++++++++++++ + drivers/net/ethernet/lantiq_xrx200_sw.h | 1328 +++++++++++++++++++++++ + 5 files changed, 3297 insertions(+), 1 deletion(-) + create mode 100644 drivers/net/ethernet/lantiq_pce.h + create mode 100644 drivers/net/ethernet/lantiq_xrx200.c + create mode 100644 drivers/net/ethernet/lantiq_xrx200_sw.h + +--- a/drivers/net/ethernet/Kconfig ++++ b/drivers/net/ethernet/Kconfig +@@ -107,7 +107,13 @@ config LANTIQ_ETOP + tristate "Lantiq SoC ETOP driver" + depends on SOC_TYPE_XWAY + ---help--- +- Support for the MII0 inside the Lantiq SoC ++ Support for the MII0 inside the Lantiq ADSL SoC ++ ++config LANTIQ_XRX200 ++ tristate "Lantiq SoC XRX200 driver" ++ depends on SOC_TYPE_XWAY ++ ---help--- ++ Support for the MII0 inside the Lantiq VDSL SoC + + source "drivers/net/ethernet/marvell/Kconfig" + source "drivers/net/ethernet/mediatek/Kconfig" +--- a/drivers/net/ethernet/Makefile ++++ b/drivers/net/ethernet/Makefile +@@ -50,6 +50,7 @@ obj-$(CONFIG_NET_VENDOR_XSCALE) += xscal + obj-$(CONFIG_JME) += jme.o + obj-$(CONFIG_KORINA) += korina.o + obj-$(CONFIG_LANTIQ_ETOP) += lantiq_etop.o ++obj-$(CONFIG_LANTIQ_XRX200) += lantiq_xrx200.o + obj-$(CONFIG_NET_VENDOR_MARVELL) += marvell/ + obj-$(CONFIG_NET_VENDOR_MEDIATEK) += mediatek/ + obj-$(CONFIG_NET_VENDOR_MELLANOX) += mellanox/ +--- /dev/null ++++ b/drivers/net/ethernet/lantiq_pce.h +@@ -0,0 +1,163 @@ ++/* ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms of the GNU General Public License version 2 as published ++ * by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ * ++ * You should have received a copy of the GNU General Public License ++ * along with this program; if not, write to the Free Software ++ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307, USA. ++ * ++ * Copyright (C) 2010 Lantiq Deutschland GmbH ++ * Copyright (C) 2012 John Crispin ++ * ++ * PCE microcode extracted from UGW5.2 switch api ++ */ ++ ++/* Switch API Micro Code V0.3 */ ++enum { ++ OUT_MAC0 = 0, ++ OUT_MAC1, ++ OUT_MAC2, ++ OUT_MAC3, ++ OUT_MAC4, ++ OUT_MAC5, ++ OUT_ETHTYP, ++ OUT_VTAG0, ++ OUT_VTAG1, ++ OUT_ITAG0, ++ OUT_ITAG1, /*10 */ ++ OUT_ITAG2, ++ OUT_ITAG3, ++ OUT_IP0, ++ OUT_IP1, ++ OUT_IP2, ++ OUT_IP3, ++ OUT_SIP0, ++ OUT_SIP1, ++ OUT_SIP2, ++ OUT_SIP3, /*20*/ ++ OUT_SIP4, ++ OUT_SIP5, ++ OUT_SIP6, ++ OUT_SIP7, ++ OUT_DIP0, ++ OUT_DIP1, ++ OUT_DIP2, ++ OUT_DIP3, ++ OUT_DIP4, ++ OUT_DIP5, /*30*/ ++ OUT_DIP6, ++ OUT_DIP7, ++ OUT_SESID, ++ OUT_PROT, ++ OUT_APP0, ++ OUT_APP1, ++ OUT_IGMP0, ++ OUT_IGMP1, ++ OUT_IPOFF, /*39*/ ++ OUT_NONE = 63 ++}; ++ ++/* parser's microcode length type */ ++#define INSTR 0 ++#define IPV6 1 ++#define LENACCU 2 ++ ++/* parser's microcode flag type */ ++enum { ++ FLAG_ITAG = 0, ++ FLAG_VLAN, ++ FLAG_SNAP, ++ FLAG_PPPOE, ++ FLAG_IPV6, ++ FLAG_IPV6FL, ++ FLAG_IPV4, ++ FLAG_IGMP, ++ FLAG_TU, ++ FLAG_HOP, ++ FLAG_NN1, /*10 */ ++ FLAG_NN2, ++ FLAG_END, ++ FLAG_NO, /*13*/ ++}; ++ ++/* Micro code version V2_11 (extension for parsing IPv6 in PPPoE) */ ++#define MC_ENTRY(val, msk, ns, out, len, type, flags, ipv4_len) \ ++ { {val, msk, (ns<<10 | out<<4 | len>>1), (len&1)<<15 | type<<13 | flags<<9 | ipv4_len<<8 }} ++struct pce_microcode { ++ unsigned short val[4]; ++/* unsigned short val_2; ++ unsigned short val_1; ++ unsigned short val_0;*/ ++} pce_microcode[] = { ++ /* value mask ns fields L type flags ipv4_len */ ++ MC_ENTRY(0x88c3, 0xFFFF, 1, OUT_ITAG0, 4, INSTR, FLAG_ITAG, 0), ++ MC_ENTRY(0x8100, 0xFFFF, 2, OUT_VTAG0, 2, INSTR, FLAG_VLAN, 0), ++ MC_ENTRY(0x88A8, 0xFFFF, 1, OUT_VTAG0, 2, INSTR, FLAG_VLAN, 0), ++ MC_ENTRY(0x8100, 0xFFFF, 1, OUT_VTAG0, 2, INSTR, FLAG_VLAN, 0), ++ MC_ENTRY(0x8864, 0xFFFF, 17, OUT_ETHTYP, 1, INSTR, FLAG_NO, 0), ++ MC_ENTRY(0x0800, 0xFFFF, 21, OUT_ETHTYP, 1, INSTR, FLAG_NO, 0), ++ MC_ENTRY(0x86DD, 0xFFFF, 22, OUT_ETHTYP, 1, INSTR, FLAG_NO, 0), ++ MC_ENTRY(0x8863, 0xFFFF, 16, OUT_ETHTYP, 1, INSTR, FLAG_NO, 0), ++ MC_ENTRY(0x0000, 0xF800, 10, OUT_NONE, 0, INSTR, FLAG_NO, 0), ++ MC_ENTRY(0x0000, 0x0000, 38, OUT_ETHTYP, 1, INSTR, FLAG_NO, 0), ++ MC_ENTRY(0x0600, 0x0600, 38, OUT_ETHTYP, 1, INSTR, FLAG_NO, 0), ++ MC_ENTRY(0x0000, 0x0000, 12, OUT_NONE, 1, INSTR, FLAG_NO, 0), ++ MC_ENTRY(0xAAAA, 0xFFFF, 14, OUT_NONE, 1, INSTR, FLAG_NO, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_NONE, 0, INSTR, FLAG_NO, 0), ++ MC_ENTRY(0x0300, 0xFF00, 39, OUT_NONE, 0, INSTR, FLAG_SNAP, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_NONE, 0, INSTR, FLAG_NO, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_DIP7, 3, INSTR, FLAG_NO, 0), ++ MC_ENTRY(0x0000, 0x0000, 18, OUT_DIP7, 3, INSTR, FLAG_PPPOE, 0), ++ MC_ENTRY(0x0021, 0xFFFF, 21, OUT_NONE, 1, INSTR, FLAG_NO, 0), ++ MC_ENTRY(0x0057, 0xFFFF, 22, OUT_NONE, 1, INSTR, FLAG_NO, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_NONE, 0, INSTR, FLAG_NO, 0), ++ MC_ENTRY(0x4000, 0xF000, 24, OUT_IP0, 4, INSTR, FLAG_IPV4, 1), ++ MC_ENTRY(0x6000, 0xF000, 27, OUT_IP0, 3, INSTR, FLAG_IPV6, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_NONE, 0, INSTR, FLAG_NO, 0), ++ MC_ENTRY(0x0000, 0x0000, 25, OUT_IP3, 2, INSTR, FLAG_NO, 0), ++ MC_ENTRY(0x0000, 0x0000, 26, OUT_SIP0, 4, INSTR, FLAG_NO, 0), ++ MC_ENTRY(0x0000, 0x0000, 38, OUT_NONE, 0, LENACCU, FLAG_NO, 0), ++ MC_ENTRY(0x1100, 0xFF00, 37, OUT_PROT, 1, INSTR, FLAG_NO, 0), ++ MC_ENTRY(0x0600, 0xFF00, 37, OUT_PROT, 1, INSTR, FLAG_NO, 0), ++ MC_ENTRY(0x0000, 0xFF00, 33, OUT_IP3, 17, INSTR, FLAG_HOP, 0), ++ MC_ENTRY(0x2B00, 0xFF00, 33, OUT_IP3, 17, INSTR, FLAG_NN1, 0), ++ MC_ENTRY(0x3C00, 0xFF00, 33, OUT_IP3, 17, INSTR, FLAG_NN2, 0), ++ MC_ENTRY(0x0000, 0x0000, 37, OUT_PROT, 1, INSTR, FLAG_NO, 0), ++ MC_ENTRY(0x0000, 0xFF00, 33, OUT_NONE, 0, IPV6, FLAG_HOP, 0), ++ MC_ENTRY(0x2B00, 0xFF00, 33, OUT_NONE, 0, IPV6, FLAG_NN1, 0), ++ MC_ENTRY(0x3C00, 0xFF00, 33, OUT_NONE, 0, IPV6, FLAG_NN2, 0), ++ MC_ENTRY(0x0000, 0x0000, 38, OUT_PROT, 1, IPV6, FLAG_NO, 0), ++ MC_ENTRY(0x0000, 0x0000, 38, OUT_SIP0, 16, INSTR, FLAG_NO, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_APP0, 4, INSTR, FLAG_IGMP, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_NONE, 0, INSTR, FLAG_END, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_NONE, 0, INSTR, FLAG_END, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_NONE, 0, INSTR, FLAG_END, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_NONE, 0, INSTR, FLAG_END, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_NONE, 0, INSTR, FLAG_END, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_NONE, 0, INSTR, FLAG_END, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_NONE, 0, INSTR, FLAG_END, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_NONE, 0, INSTR, FLAG_END, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_NONE, 0, INSTR, FLAG_END, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_NONE, 0, INSTR, FLAG_END, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_NONE, 0, INSTR, FLAG_END, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_NONE, 0, INSTR, FLAG_END, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_NONE, 0, INSTR, FLAG_END, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_NONE, 0, INSTR, FLAG_END, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_NONE, 0, INSTR, FLAG_END, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_NONE, 0, INSTR, FLAG_END, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_NONE, 0, INSTR, FLAG_END, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_NONE, 0, INSTR, FLAG_END, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_NONE, 0, INSTR, FLAG_END, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_NONE, 0, INSTR, FLAG_END, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_NONE, 0, INSTR, FLAG_END, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_NONE, 0, INSTR, FLAG_END, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_NONE, 0, INSTR, FLAG_END, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_NONE, 0, INSTR, FLAG_END, 0), ++ MC_ENTRY(0x0000, 0x0000, 39, OUT_NONE, 0, INSTR, FLAG_END, 0), ++}; +--- /dev/null ++++ b/drivers/net/ethernet/lantiq_xrx200.c +@@ -0,0 +1,1887 @@ ++/* ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms of the GNU General Public License version 2 as published ++ * by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ * ++ * You should have received a copy of the GNU General Public License ++ * along with this program; if not, write to the Free Software ++ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307, USA. ++ * ++ * Copyright (C) 2010 Lantiq Deutschland ++ * Copyright (C) 2012 John Crispin ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++#include ++#include ++#include ++ ++#include ++#include ++ ++#include "lantiq_pce.h" ++#include "lantiq_xrx200_sw.h" ++ ++#define SW_POLLING ++#define SW_ROUTING ++ ++#ifdef SW_ROUTING ++#define XRX200_MAX_DEV 2 ++#else ++#define XRX200_MAX_DEV 1 ++#endif ++ ++#define XRX200_MAX_VLAN 64 ++#define XRX200_PCE_ACTVLAN_IDX 0x01 ++#define XRX200_PCE_VLANMAP_IDX 0x02 ++ ++#define XRX200_MAX_PORT 7 ++#define XRX200_MAX_DMA 8 ++ ++#define XRX200_HEADROOM 4 ++ ++#define XRX200_TX_TIMEOUT (10 * HZ) ++ ++/* port type */ ++#define XRX200_PORT_TYPE_PHY 1 ++#define XRX200_PORT_TYPE_MAC 2 ++ ++/* DMA */ ++#define XRX200_DMA_DATA_LEN 0x600 ++#define XRX200_DMA_IRQ INT_NUM_IM2_IRL0 ++#define XRX200_DMA_RX 0 ++#define XRX200_DMA_TX 1 ++#define XRX200_DMA_TX_2 3 ++#define XRX200_DMA_IS_TX(x) (x%2) ++#define XRX200_DMA_IS_RX(x) (!XRX200_DMA_IS_TX(x)) ++ ++/* fetch / store dma */ ++#define FDMA_PCTRL0 0x2A00 ++#define FDMA_PCTRLx(x) (FDMA_PCTRL0 + (x * 0x18)) ++#define SDMA_PCTRL0 0x2F00 ++#define SDMA_PCTRLx(x) (SDMA_PCTRL0 + (x * 0x18)) ++ ++/* buffer management */ ++#define BM_PCFG0 0x200 ++#define BM_PCFGx(x) (BM_PCFG0 + (x * 8)) ++ ++/* MDIO */ ++#define MDIO_GLOB 0x0000 ++#define MDIO_CTRL 0x0020 ++#define MDIO_READ 0x0024 ++#define MDIO_WRITE 0x0028 ++#define MDIO_PHY0 0x0054 ++#define MDIO_PHY(x) (0x0054 - (x * sizeof(unsigned))) ++#define MDIO_CLK_CFG0 0x002C ++#define MDIO_CLK_CFG1 0x0030 ++ ++#define MDIO_GLOB_ENABLE 0x8000 ++#define MDIO_BUSY BIT(12) ++#define MDIO_RD BIT(11) ++#define MDIO_WR BIT(10) ++#define MDIO_MASK 0x1f ++#define MDIO_ADDRSHIFT 5 ++#define MDIO1_25MHZ 9 ++ ++#define MDIO_PHY_LINK_DOWN 0x4000 ++#define MDIO_PHY_LINK_UP 0x2000 ++ ++#define MDIO_PHY_SPEED_M10 0x0000 ++#define MDIO_PHY_SPEED_M100 0x0800 ++#define MDIO_PHY_SPEED_G1 0x1000 ++ ++#define MDIO_PHY_FDUP_EN 0x0200 ++#define MDIO_PHY_FDUP_DIS 0x0600 ++ ++#define MDIO_PHY_LINK_MASK 0x6000 ++#define MDIO_PHY_SPEED_MASK 0x1800 ++#define MDIO_PHY_FDUP_MASK 0x0600 ++#define MDIO_PHY_ADDR_MASK 0x001f ++#define MDIO_UPDATE_MASK MDIO_PHY_ADDR_MASK | MDIO_PHY_LINK_MASK | \ ++ MDIO_PHY_SPEED_MASK | MDIO_PHY_FDUP_MASK ++ ++/* MII */ ++#define MII_CFG(p) (p * 8) ++ ++#define MII_CFG_EN BIT(14) ++ ++#define MII_CFG_MODE_MIIP 0x0 ++#define MII_CFG_MODE_MIIM 0x1 ++#define MII_CFG_MODE_RMIIP 0x2 ++#define MII_CFG_MODE_RMIIM 0x3 ++#define MII_CFG_MODE_RGMII 0x4 ++#define MII_CFG_MODE_MASK 0xf ++ ++#define MII_CFG_RATE_M2P5 0x00 ++#define MII_CFG_RATE_M25 0x10 ++#define MII_CFG_RATE_M125 0x20 ++#define MII_CFG_RATE_M50 0x30 ++#define MII_CFG_RATE_AUTO 0x40 ++#define MII_CFG_RATE_MASK 0x70 ++ ++/* cpu port mac */ ++#define PMAC_HD_CTL 0x0000 ++#define PMAC_RX_IPG 0x0024 ++#define PMAC_EWAN 0x002c ++ ++#define PMAC_IPG_MASK 0xf ++#define PMAC_HD_CTL_AS 0x0008 ++#define PMAC_HD_CTL_AC 0x0004 ++#define PMAC_HD_CTL_RC 0x0010 ++#define PMAC_HD_CTL_RXSH 0x0040 ++#define PMAC_HD_CTL_AST 0x0080 ++#define PMAC_HD_CTL_RST 0x0100 ++ ++/* PCE */ ++#define PCE_TBL_KEY(x) (0x1100 + ((7 - x) * 4)) ++#define PCE_TBL_MASK 0x1120 ++#define PCE_TBL_VAL(x) (0x1124 + ((4 - x) * 4)) ++#define PCE_TBL_ADDR 0x1138 ++#define PCE_TBL_CTRL 0x113c ++#define PCE_PMAP1 0x114c ++#define PCE_PMAP2 0x1150 ++#define PCE_PMAP3 0x1154 ++#define PCE_GCTRL_REG(x) (0x1158 + (x * 4)) ++#define PCE_PCTRL_REG(p, x) (0x1200 + (((p * 0xa) + x) * 4)) ++ ++#define PCE_TBL_BUSY BIT(15) ++#define PCE_TBL_CFG_ADDR_MASK 0x1f ++#define PCE_TBL_CFG_ADWR 0x20 ++#define PCE_TBL_CFG_ADWR_MASK 0x60 ++#define PCE_INGRESS BIT(11) ++ ++/* MAC */ ++#define MAC_FLEN_REG (0x2314) ++#define MAC_CTRL_REG(p, x) (0x240c + (((p * 0xc) + x) * 4)) ++ ++/* buffer management */ ++#define BM_PCFG(p) (0x200 + (p * 8)) ++ ++/* special tag in TX path header */ ++#define SPID_SHIFT 24 ++#define DPID_SHIFT 16 ++#define DPID_ENABLE 1 ++#define SPID_CPU_PORT 2 ++#define PORT_MAP_SEL BIT(15) ++#define PORT_MAP_EN BIT(14) ++#define PORT_MAP_SHIFT 1 ++#define PORT_MAP_MASK 0x3f ++ ++#define SPPID_MASK 0x7 ++#define SPPID_SHIFT 4 ++ ++/* MII regs not yet in linux */ ++#define MDIO_DEVAD_NONE (-1) ++#define ADVERTIZE_MPD (1 << 10) ++ ++struct xrx200_port { ++ u8 num; ++ u8 phy_addr; ++ u16 flags; ++ phy_interface_t phy_if; ++ ++ int link; ++ int gpio; ++ enum of_gpio_flags gpio_flags; ++ ++ struct phy_device *phydev; ++ struct device_node *phy_node; ++}; ++ ++struct xrx200_chan { ++ int idx; ++ int refcount; ++ int tx_free; ++ ++ struct net_device dummy_dev; ++ struct net_device *devs[XRX200_MAX_DEV]; ++ ++ struct tasklet_struct tasklet; ++ struct napi_struct napi; ++ struct ltq_dma_channel dma; ++ struct sk_buff *skb[LTQ_DESC_NUM]; ++ ++ spinlock_t lock; ++}; ++ ++struct xrx200_hw { ++ struct clk *clk; ++ struct mii_bus *mii_bus; ++ ++ struct xrx200_chan chan[XRX200_MAX_DMA]; ++ u16 vlan_vid[XRX200_MAX_VLAN]; ++ u16 vlan_port_map[XRX200_MAX_VLAN]; ++ ++ struct net_device *devs[XRX200_MAX_DEV]; ++ int num_devs; ++ ++ int port_map[XRX200_MAX_PORT]; ++ unsigned short wan_map; ++ ++ struct switch_dev swdev; ++}; ++ ++struct xrx200_priv { ++ struct net_device_stats stats; ++ int id; ++ ++ struct xrx200_port port[XRX200_MAX_PORT]; ++ int num_port; ++ bool wan; ++ bool sw; ++ unsigned short port_map; ++ unsigned char mac[6]; ++ ++ struct xrx200_hw *hw; ++}; ++ ++static __iomem void *xrx200_switch_membase; ++static __iomem void *xrx200_mii_membase; ++static __iomem void *xrx200_mdio_membase; ++static __iomem void *xrx200_pmac_membase; ++ ++#define ltq_switch_r32(x) ltq_r32(xrx200_switch_membase + (x)) ++#define ltq_switch_w32(x, y) ltq_w32(x, xrx200_switch_membase + (y)) ++#define ltq_switch_w32_mask(x, y, z) \ ++ ltq_w32_mask(x, y, xrx200_switch_membase + (z)) ++ ++#define ltq_mdio_r32(x) ltq_r32(xrx200_mdio_membase + (x)) ++#define ltq_mdio_w32(x, y) ltq_w32(x, xrx200_mdio_membase + (y)) ++#define ltq_mdio_w32_mask(x, y, z) \ ++ ltq_w32_mask(x, y, xrx200_mdio_membase + (z)) ++ ++#define ltq_mii_r32(x) ltq_r32(xrx200_mii_membase + (x)) ++#define ltq_mii_w32(x, y) ltq_w32(x, xrx200_mii_membase + (y)) ++#define ltq_mii_w32_mask(x, y, z) \ ++ ltq_w32_mask(x, y, xrx200_mii_membase + (z)) ++ ++#define ltq_pmac_r32(x) ltq_r32(xrx200_pmac_membase + (x)) ++#define ltq_pmac_w32(x, y) ltq_w32(x, xrx200_pmac_membase + (y)) ++#define ltq_pmac_w32_mask(x, y, z) \ ++ ltq_w32_mask(x, y, xrx200_pmac_membase + (z)) ++ ++#define XRX200_GLOBAL_REGATTR(reg) \ ++ .id = reg, \ ++ .type = SWITCH_TYPE_INT, \ ++ .set = xrx200_set_global_attr, \ ++ .get = xrx200_get_global_attr ++ ++#define XRX200_PORT_REGATTR(reg) \ ++ .id = reg, \ ++ .type = SWITCH_TYPE_INT, \ ++ .set = xrx200_set_port_attr, \ ++ .get = xrx200_get_port_attr ++ ++static int xrx200sw_read_x(int reg, int x) ++{ ++ int value, mask, addr; ++ ++ addr = xrx200sw_reg[reg].offset + (xrx200sw_reg[reg].mult * x); ++ value = ltq_switch_r32(addr); ++ mask = (1 << xrx200sw_reg[reg].size) - 1; ++ value = (value >> xrx200sw_reg[reg].shift); ++ ++ return (value & mask); ++} ++ ++static int xrx200sw_read(int reg) ++{ ++ return xrx200sw_read_x(reg, 0); ++} ++ ++static void xrx200sw_write_x(int value, int reg, int x) ++{ ++ int mask, addr; ++ ++ addr = xrx200sw_reg[reg].offset + (xrx200sw_reg[reg].mult * x); ++ mask = (1 << xrx200sw_reg[reg].size) - 1; ++ mask = (mask << xrx200sw_reg[reg].shift); ++ value = (value << xrx200sw_reg[reg].shift) & mask; ++ ++ ltq_switch_w32_mask(mask, value, addr); ++} ++ ++static void xrx200sw_write(int value, int reg) ++{ ++ xrx200sw_write_x(value, reg, 0); ++} ++ ++struct xrx200_pce_table_entry { ++ int index; // PCE_TBL_ADDR.ADDR = pData->table_index ++ int table; // PCE_TBL_CTRL.ADDR = pData->table ++ unsigned short key[8]; ++ unsigned short val[5]; ++ unsigned short mask; ++ unsigned short type; ++ unsigned short valid; ++ unsigned short gmap; ++}; ++ ++static int xrx200_pce_table_entry_read(struct xrx200_pce_table_entry *tbl) ++{ ++ // wait until hardware is ready ++ while (xrx200sw_read(XRX200_PCE_TBL_CTRL_BAS)) {}; ++ ++ // prepare the table access: ++ // PCE_TBL_ADDR.ADDR = pData->table_index ++ xrx200sw_write(tbl->index, XRX200_PCE_TBL_ADDR_ADDR); ++ // PCE_TBL_CTRL.ADDR = pData->table ++ xrx200sw_write(tbl->table, XRX200_PCE_TBL_CTRL_ADDR); ++ ++ //(address-based read) ++ xrx200sw_write(0, XRX200_PCE_TBL_CTRL_OPMOD); // OPMOD_ADRD ++ ++ xrx200sw_write(1, XRX200_PCE_TBL_CTRL_BAS); // start access ++ ++ // wait until hardware is ready ++ while (xrx200sw_read(XRX200_PCE_TBL_CTRL_BAS)) {}; ++ ++ // read the keys ++ tbl->key[7] = xrx200sw_read(XRX200_PCE_TBL_KEY_7); ++ tbl->key[6] = xrx200sw_read(XRX200_PCE_TBL_KEY_6); ++ tbl->key[5] = xrx200sw_read(XRX200_PCE_TBL_KEY_5); ++ tbl->key[4] = xrx200sw_read(XRX200_PCE_TBL_KEY_4); ++ tbl->key[3] = xrx200sw_read(XRX200_PCE_TBL_KEY_3); ++ tbl->key[2] = xrx200sw_read(XRX200_PCE_TBL_KEY_2); ++ tbl->key[1] = xrx200sw_read(XRX200_PCE_TBL_KEY_1); ++ tbl->key[0] = xrx200sw_read(XRX200_PCE_TBL_KEY_0); ++ ++ // read the values ++ tbl->val[4] = xrx200sw_read(XRX200_PCE_TBL_VAL_4); ++ tbl->val[3] = xrx200sw_read(XRX200_PCE_TBL_VAL_3); ++ tbl->val[2] = xrx200sw_read(XRX200_PCE_TBL_VAL_2); ++ tbl->val[1] = xrx200sw_read(XRX200_PCE_TBL_VAL_1); ++ tbl->val[0] = xrx200sw_read(XRX200_PCE_TBL_VAL_0); ++ ++ // read the mask ++ tbl->mask = xrx200sw_read(XRX200_PCE_TBL_MASK_0); ++ // read the type ++ tbl->type = xrx200sw_read(XRX200_PCE_TBL_CTRL_TYPE); ++ // read the valid flag ++ tbl->valid = xrx200sw_read(XRX200_PCE_TBL_CTRL_VLD); ++ // read the group map ++ tbl->gmap = xrx200sw_read(XRX200_PCE_TBL_CTRL_GMAP); ++ ++ return 0; ++} ++ ++static int xrx200_pce_table_entry_write(struct xrx200_pce_table_entry *tbl) ++{ ++ // wait until hardware is ready ++ while (xrx200sw_read(XRX200_PCE_TBL_CTRL_BAS)) {}; ++ ++ // prepare the table access: ++ // PCE_TBL_ADDR.ADDR = pData->table_index ++ xrx200sw_write(tbl->index, XRX200_PCE_TBL_ADDR_ADDR); ++ // PCE_TBL_CTRL.ADDR = pData->table ++ xrx200sw_write(tbl->table, XRX200_PCE_TBL_CTRL_ADDR); ++ ++ //(address-based write) ++ xrx200sw_write(1, XRX200_PCE_TBL_CTRL_OPMOD); // OPMOD_ADRD ++ ++ // read the keys ++ xrx200sw_write(tbl->key[7], XRX200_PCE_TBL_KEY_7); ++ xrx200sw_write(tbl->key[6], XRX200_PCE_TBL_KEY_6); ++ xrx200sw_write(tbl->key[5], XRX200_PCE_TBL_KEY_5); ++ xrx200sw_write(tbl->key[4], XRX200_PCE_TBL_KEY_4); ++ xrx200sw_write(tbl->key[3], XRX200_PCE_TBL_KEY_3); ++ xrx200sw_write(tbl->key[2], XRX200_PCE_TBL_KEY_2); ++ xrx200sw_write(tbl->key[1], XRX200_PCE_TBL_KEY_1); ++ xrx200sw_write(tbl->key[0], XRX200_PCE_TBL_KEY_0); ++ ++ // read the values ++ xrx200sw_write(tbl->val[4], XRX200_PCE_TBL_VAL_4); ++ xrx200sw_write(tbl->val[3], XRX200_PCE_TBL_VAL_3); ++ xrx200sw_write(tbl->val[2], XRX200_PCE_TBL_VAL_2); ++ xrx200sw_write(tbl->val[1], XRX200_PCE_TBL_VAL_1); ++ xrx200sw_write(tbl->val[0], XRX200_PCE_TBL_VAL_0); ++ ++ // read the mask ++ xrx200sw_write(tbl->mask, XRX200_PCE_TBL_MASK_0); ++ // read the type ++ xrx200sw_write(tbl->type, XRX200_PCE_TBL_CTRL_TYPE); ++ // read the valid flag ++ xrx200sw_write(tbl->valid, XRX200_PCE_TBL_CTRL_VLD); ++ // read the group map ++ xrx200sw_write(tbl->gmap, XRX200_PCE_TBL_CTRL_GMAP); ++ ++ xrx200sw_write(1, XRX200_PCE_TBL_CTRL_BAS); // start access ++ ++ // wait until hardware is ready ++ while (xrx200sw_read(XRX200_PCE_TBL_CTRL_BAS)) {}; ++ ++ return 0; ++} ++ ++static void xrx200sw_fixup_pvids(void) ++{ ++ int index, p, portmap, untagged; ++ struct xrx200_pce_table_entry tem; ++ struct xrx200_pce_table_entry tev; ++ ++ portmap = 0; ++ for (p = 0; p < XRX200_MAX_PORT; p++) ++ portmap |= BIT(p); ++ ++ tem.table = XRX200_PCE_VLANMAP_IDX; ++ tev.table = XRX200_PCE_ACTVLAN_IDX; ++ ++ for (index = XRX200_MAX_VLAN; index-- > 0;) ++ { ++ tev.index = index; ++ xrx200_pce_table_entry_read(&tev); ++ ++ if (tev.valid == 0) ++ continue; ++ ++ tem.index = index; ++ xrx200_pce_table_entry_read(&tem); ++ ++ if (tem.val[0] == 0) ++ continue; ++ ++ untagged = portmap & (tem.val[1] ^ tem.val[2]); ++ ++ for (p = 0; p < XRX200_MAX_PORT; p++) ++ if (untagged & BIT(p)) ++ { ++ portmap &= ~BIT(p); ++ xrx200sw_write_x(index, XRX200_PCE_DEFPVID_PVID, p); ++ } ++ ++ for (p = 0; p < XRX200_MAX_PORT; p++) ++ if (portmap & BIT(p)) ++ xrx200sw_write_x(index, XRX200_PCE_DEFPVID_PVID, p); ++ } ++} ++ ++// swconfig interface ++static void xrx200_hw_init(struct xrx200_hw *hw); ++ ++// global ++static int xrx200sw_reset_switch(struct switch_dev *dev) ++{ ++ struct xrx200_hw *hw = container_of(dev, struct xrx200_hw, swdev); ++ ++ xrx200_hw_init(hw); ++ ++ return 0; ++} ++ ++static int xrx200_set_vlan_mode_enable(struct switch_dev *dev, const struct switch_attr *attr, struct switch_val *val) ++{ ++ int p; ++ ++ if ((attr->max > 0) && (val->value.i > attr->max)) ++ return -EINVAL; ++ ++ for (p = 0; p < XRX200_MAX_PORT; p++) { ++ xrx200sw_write_x(val->value.i, XRX200_PCE_VCTRL_VEMR, p); ++ xrx200sw_write_x(val->value.i, XRX200_PCE_VCTRL_VIMR, p); ++ } ++ ++ xrx200sw_write(val->value.i, XRX200_PCE_GCTRL_0_VLAN); ++ return 0; ++} ++ ++static int xrx200_get_vlan_mode_enable(struct switch_dev *dev, const struct switch_attr *attr, struct switch_val *val) ++{ ++ val->value.i = xrx200sw_read(attr->id); ++ return 0; ++} ++ ++static int xrx200_set_global_attr(struct switch_dev *dev, const struct switch_attr *attr, struct switch_val *val) ++{ ++ if ((attr->max > 0) && (val->value.i > attr->max)) ++ return -EINVAL; ++ ++ xrx200sw_write(val->value.i, attr->id); ++ return 0; ++} ++ ++static int xrx200_get_global_attr(struct switch_dev *dev, const struct switch_attr *attr, struct switch_val *val) ++{ ++ val->value.i = xrx200sw_read(attr->id); ++ return 0; ++} ++ ++// vlan ++static int xrx200sw_set_vlan_vid(struct switch_dev *dev, const struct switch_attr *attr, ++ struct switch_val *val) ++{ ++ struct xrx200_hw *hw = container_of(dev, struct xrx200_hw, swdev); ++ int i; ++ struct xrx200_pce_table_entry tev; ++ struct xrx200_pce_table_entry tem; ++ ++ tev.table = XRX200_PCE_ACTVLAN_IDX; ++ ++ for (i = 0; i < XRX200_MAX_VLAN; i++) ++ { ++ tev.index = i; ++ xrx200_pce_table_entry_read(&tev); ++ if (tev.key[0] == val->value.i && i != val->port_vlan) ++ return -EINVAL; ++ } ++ ++ hw->vlan_vid[val->port_vlan] = val->value.i; ++ ++ tev.index = val->port_vlan; ++ xrx200_pce_table_entry_read(&tev); ++ tev.key[0] = val->value.i; ++ tev.valid = val->value.i > 0; ++ xrx200_pce_table_entry_write(&tev); ++ ++ tem.table = XRX200_PCE_VLANMAP_IDX; ++ tem.index = val->port_vlan; ++ xrx200_pce_table_entry_read(&tem); ++ tem.val[0] = val->value.i; ++ xrx200_pce_table_entry_write(&tem); ++ ++ xrx200sw_fixup_pvids(); ++ return 0; ++} ++ ++static int xrx200sw_get_vlan_vid(struct switch_dev *dev, const struct switch_attr *attr, ++ struct switch_val *val) ++{ ++ struct xrx200_pce_table_entry te; ++ ++ te.table = XRX200_PCE_ACTVLAN_IDX; ++ te.index = val->port_vlan; ++ xrx200_pce_table_entry_read(&te); ++ val->value.i = te.key[0]; ++ ++ return 0; ++} ++ ++static int xrx200sw_set_vlan_ports(struct switch_dev *dev, struct switch_val *val) ++{ ++ struct xrx200_hw *hw = container_of(dev, struct xrx200_hw, swdev); ++ int i, portmap, tagmap, untagged; ++ struct xrx200_pce_table_entry tem; ++ ++ portmap = 0; ++ tagmap = 0; ++ for (i = 0; i < val->len; i++) ++ { ++ struct switch_port *p = &val->value.ports[i]; ++ ++ portmap |= (1 << p->id); ++ if (p->flags & (1 << SWITCH_PORT_FLAG_TAGGED)) ++ tagmap |= (1 << p->id); ++ } ++ ++ tem.table = XRX200_PCE_VLANMAP_IDX; ++ ++ untagged = portmap ^ tagmap; ++ for (i = 0; i < XRX200_MAX_VLAN; i++) ++ { ++ tem.index = i; ++ xrx200_pce_table_entry_read(&tem); ++ ++ if (tem.val[0] == 0) ++ continue; ++ ++ if ((untagged & (tem.val[1] ^ tem.val[2])) && (val->port_vlan != i)) ++ return -EINVAL; ++ } ++ ++ tem.index = val->port_vlan; ++ xrx200_pce_table_entry_read(&tem); ++ ++ // auto-enable this vlan if not enabled already ++ if (tem.val[0] == 0) ++ { ++ struct switch_val v; ++ v.port_vlan = val->port_vlan; ++ v.value.i = val->port_vlan; ++ if(xrx200sw_set_vlan_vid(dev, NULL, &v)) ++ return -EINVAL; ++ ++ //read updated tem ++ tem.index = val->port_vlan; ++ xrx200_pce_table_entry_read(&tem); ++ } ++ ++ tem.val[1] = portmap; ++ tem.val[2] = tagmap; ++ xrx200_pce_table_entry_write(&tem); ++ ++ ltq_switch_w32_mask(0, portmap, PCE_PMAP2); ++ ltq_switch_w32_mask(0, portmap, PCE_PMAP3); ++ hw->vlan_port_map[val->port_vlan] = portmap; ++ ++ xrx200sw_fixup_pvids(); ++ ++ return 0; ++} ++ ++static int xrx200sw_get_vlan_ports(struct switch_dev *dev, struct switch_val *val) ++{ ++ int i; ++ unsigned short ports, tags; ++ struct xrx200_pce_table_entry tem; ++ ++ tem.table = XRX200_PCE_VLANMAP_IDX; ++ tem.index = val->port_vlan; ++ xrx200_pce_table_entry_read(&tem); ++ ++ ports = tem.val[1]; ++ tags = tem.val[2]; ++ ++ for (i = 0; i < XRX200_MAX_PORT; i++) { ++ struct switch_port *p; ++ ++ if (!(ports & (1 << i))) ++ continue; ++ ++ p = &val->value.ports[val->len++]; ++ p->id = i; ++ if (tags & (1 << i)) ++ p->flags = (1 << SWITCH_PORT_FLAG_TAGGED); ++ else ++ p->flags = 0; ++ } ++ ++ return 0; ++} ++ ++static int xrx200sw_set_vlan_enable(struct switch_dev *dev, const struct switch_attr *attr, ++ struct switch_val *val) ++{ ++ struct xrx200_pce_table_entry tev; ++ ++ tev.table = XRX200_PCE_ACTVLAN_IDX; ++ tev.index = val->port_vlan; ++ xrx200_pce_table_entry_read(&tev); ++ ++ if (tev.key[0] == 0) ++ return -EINVAL; ++ ++ tev.valid = val->value.i; ++ xrx200_pce_table_entry_write(&tev); ++ ++ xrx200sw_fixup_pvids(); ++ return 0; ++} ++ ++static int xrx200sw_get_vlan_enable(struct switch_dev *dev, const struct switch_attr *attr, ++ struct switch_val *val) ++{ ++ struct xrx200_pce_table_entry tev; ++ ++ tev.table = XRX200_PCE_ACTVLAN_IDX; ++ tev.index = val->port_vlan; ++ xrx200_pce_table_entry_read(&tev); ++ val->value.i = tev.valid; ++ ++ return 0; ++} ++ ++// port ++static int xrx200sw_get_port_pvid(struct switch_dev *dev, int port, int *val) ++{ ++ struct xrx200_pce_table_entry tev; ++ ++ if (port >= XRX200_MAX_PORT) ++ return -EINVAL; ++ ++ tev.table = XRX200_PCE_ACTVLAN_IDX; ++ tev.index = xrx200sw_read_x(XRX200_PCE_DEFPVID_PVID, port); ++ xrx200_pce_table_entry_read(&tev); ++ ++ *val = tev.key[0]; ++ return 0; ++} ++ ++static int xrx200sw_get_port_link(struct switch_dev *dev, ++ int port, ++ struct switch_port_link *link) ++{ ++ if (port >= XRX200_MAX_PORT) ++ return -EINVAL; ++ ++ link->link = xrx200sw_read_x(XRX200_MAC_PSTAT_LSTAT, port); ++ if (!link->link) ++ return 0; ++ ++ link->duplex = xrx200sw_read_x(XRX200_MAC_PSTAT_FDUP, port); ++ ++ link->rx_flow = !!(xrx200sw_read_x(XRX200_MAC_CTRL_0_FCON, port) && 0x0010); ++ link->tx_flow = !!(xrx200sw_read_x(XRX200_MAC_CTRL_0_FCON, port) && 0x0020); ++ link->aneg = !(xrx200sw_read_x(XRX200_MAC_CTRL_0_FCON, port)); ++ ++ link->speed = SWITCH_PORT_SPEED_10; ++ if (xrx200sw_read_x(XRX200_MAC_PSTAT_MBIT, port)) ++ link->speed = SWITCH_PORT_SPEED_100; ++ if (xrx200sw_read_x(XRX200_MAC_PSTAT_GBIT, port)) ++ link->speed = SWITCH_PORT_SPEED_1000; ++ ++ return 0; ++} ++ ++static int xrx200_set_port_attr(struct switch_dev *dev, const struct switch_attr *attr, struct switch_val *val) ++{ ++ if (val->port_vlan >= XRX200_MAX_PORT) ++ return -EINVAL; ++ ++ if ((attr->max > 0) && (val->value.i > attr->max)) ++ return -EINVAL; ++ ++ xrx200sw_write_x(val->value.i, attr->id, val->port_vlan); ++ return 0; ++} ++ ++static int xrx200_get_port_attr(struct switch_dev *dev, const struct switch_attr *attr, struct switch_val *val) ++{ ++ if (val->port_vlan >= XRX200_MAX_PORT) ++ return -EINVAL; ++ ++ val->value.i = xrx200sw_read_x(attr->id, val->port_vlan); ++ return 0; ++} ++ ++// attributes ++static struct switch_attr xrx200sw_globals[] = { ++ { ++ .type = SWITCH_TYPE_INT, ++ .set = xrx200_set_vlan_mode_enable, ++ .get = xrx200_get_vlan_mode_enable, ++ .name = "enable_vlan", ++ .description = "Enable VLAN mode", ++ .max = 1}, ++}; ++ ++static struct switch_attr xrx200sw_port[] = { ++ { ++ XRX200_PORT_REGATTR(XRX200_PCE_VCTRL_UVR), ++ .name = "uvr", ++ .description = "Unknown VLAN Rule", ++ .max = 1, ++ }, ++ { ++ XRX200_PORT_REGATTR(XRX200_PCE_VCTRL_VSR), ++ .name = "vsr", ++ .description = "VLAN Security Rule", ++ .max = 1, ++ }, ++ { ++ XRX200_PORT_REGATTR(XRX200_PCE_VCTRL_VINR), ++ .name = "vinr", ++ .description = "VLAN Ingress Tag Rule", ++ .max = 2, ++ }, ++ { ++ XRX200_PORT_REGATTR(XRX200_PCE_PCTRL_0_TVM), ++ .name = "tvm", ++ .description = "Transparent VLAN Mode", ++ .max = 1, ++ }, ++}; ++ ++static struct switch_attr xrx200sw_vlan[] = { ++ { ++ .type = SWITCH_TYPE_INT, ++ .name = "vid", ++ .description = "VLAN ID (0-4094)", ++ .set = xrx200sw_set_vlan_vid, ++ .get = xrx200sw_get_vlan_vid, ++ .max = 4094, ++ }, ++ { ++ .type = SWITCH_TYPE_INT, ++ .name = "enable", ++ .description = "Enable VLAN", ++ .set = xrx200sw_set_vlan_enable, ++ .get = xrx200sw_get_vlan_enable, ++ .max = 1, ++ }, ++}; ++ ++static const struct switch_dev_ops xrx200sw_ops = { ++ .attr_global = { ++ .attr = xrx200sw_globals, ++ .n_attr = ARRAY_SIZE(xrx200sw_globals), ++ }, ++ .attr_port = { ++ .attr = xrx200sw_port, ++ .n_attr = ARRAY_SIZE(xrx200sw_port), ++ }, ++ .attr_vlan = { ++ .attr = xrx200sw_vlan, ++ .n_attr = ARRAY_SIZE(xrx200sw_vlan), ++ }, ++ .get_vlan_ports = xrx200sw_get_vlan_ports, ++ .set_vlan_ports = xrx200sw_set_vlan_ports, ++ .get_port_pvid = xrx200sw_get_port_pvid, ++ .reset_switch = xrx200sw_reset_switch, ++ .get_port_link = xrx200sw_get_port_link, ++// .get_port_stats = xrx200sw_get_port_stats, //TODO ++}; ++ ++static int xrx200sw_init(struct xrx200_hw *hw) ++{ ++ int netdev_num; ++ ++ for (netdev_num = 0; netdev_num < hw->num_devs; netdev_num++) ++ { ++ struct switch_dev *swdev; ++ struct net_device *dev = hw->devs[netdev_num]; ++ struct xrx200_priv *priv = netdev_priv(dev); ++ if (!priv->sw) ++ continue; ++ ++ swdev = &hw->swdev; ++ ++ swdev->name = "Lantiq XRX200 Switch"; ++ swdev->vlans = XRX200_MAX_VLAN; ++ swdev->ports = XRX200_MAX_PORT; ++ swdev->cpu_port = 6; ++ swdev->ops = &xrx200sw_ops; ++ ++ register_switch(swdev, dev); ++ return 0; // enough switches ++ } ++ return 0; ++} ++ ++static int xrx200_open(struct net_device *dev) ++{ ++ struct xrx200_priv *priv = netdev_priv(dev); ++ int i; ++ ++ for (i = 0; i < XRX200_MAX_DMA; i++) { ++ if (!priv->hw->chan[i].dma.irq) ++ continue; ++ spin_lock_bh(&priv->hw->chan[i].lock); ++ if (!priv->hw->chan[i].refcount) { ++ if (XRX200_DMA_IS_RX(i)) ++ napi_enable(&priv->hw->chan[i].napi); ++ ltq_dma_open(&priv->hw->chan[i].dma); ++ } ++ priv->hw->chan[i].refcount++; ++ spin_unlock_bh(&priv->hw->chan[i].lock); ++ } ++ for (i = 0; i < priv->num_port; i++) ++ if (priv->port[i].phydev) ++ phy_start(priv->port[i].phydev); ++ netif_wake_queue(dev); ++ ++ return 0; ++} ++ ++static int xrx200_close(struct net_device *dev) ++{ ++ struct xrx200_priv *priv = netdev_priv(dev); ++ int i; ++ ++ netif_stop_queue(dev); ++ ++ for (i = 0; i < priv->num_port; i++) ++ if (priv->port[i].phydev) ++ phy_stop(priv->port[i].phydev); ++ ++ for (i = 0; i < XRX200_MAX_DMA; i++) { ++ if (!priv->hw->chan[i].dma.irq) ++ continue; ++ ++ priv->hw->chan[i].refcount--; ++ if (!priv->hw->chan[i].refcount) { ++ if (XRX200_DMA_IS_RX(i)) ++ napi_disable(&priv->hw->chan[i].napi); ++ spin_lock_bh(&priv->hw->chan[i].lock); ++ ltq_dma_close(&priv->hw->chan[XRX200_DMA_RX].dma); ++ spin_unlock_bh(&priv->hw->chan[i].lock); ++ } ++ } ++ ++ return 0; ++} ++ ++static int xrx200_alloc_skb(struct xrx200_chan *ch) ++{ ++#define DMA_PAD (NET_IP_ALIGN + NET_SKB_PAD) ++ ch->skb[ch->dma.desc] = dev_alloc_skb(XRX200_DMA_DATA_LEN + DMA_PAD); ++ if (!ch->skb[ch->dma.desc]) ++ goto skip; ++ ++ skb_reserve(ch->skb[ch->dma.desc], NET_SKB_PAD); ++ ch->dma.desc_base[ch->dma.desc].addr = dma_map_single(NULL, ++ ch->skb[ch->dma.desc]->data, XRX200_DMA_DATA_LEN, ++ DMA_FROM_DEVICE); ++ ch->dma.desc_base[ch->dma.desc].addr = ++ CPHYSADDR(ch->skb[ch->dma.desc]->data); ++ skb_reserve(ch->skb[ch->dma.desc], NET_IP_ALIGN); ++ ++skip: ++ ch->dma.desc_base[ch->dma.desc].ctl = ++ LTQ_DMA_OWN | LTQ_DMA_RX_OFFSET(NET_IP_ALIGN) | ++ XRX200_DMA_DATA_LEN; ++ ++ return 0; ++} ++ ++static void xrx200_hw_receive(struct xrx200_chan *ch, int id) ++{ ++ struct net_device *dev = ch->devs[id]; ++ struct xrx200_priv *priv = netdev_priv(dev); ++ struct ltq_dma_desc *desc = &ch->dma.desc_base[ch->dma.desc]; ++ struct sk_buff *skb = ch->skb[ch->dma.desc]; ++ int len = (desc->ctl & LTQ_DMA_SIZE_MASK); ++ int ret; ++ ++ ret = xrx200_alloc_skb(ch); ++ ++ ch->dma.desc++; ++ ch->dma.desc %= LTQ_DESC_NUM; ++ ++ if (ret) { ++ netdev_err(dev, ++ "failed to allocate new rx buffer\n"); ++ return; ++ } ++ ++ skb_put(skb, len); ++#ifdef SW_ROUTING ++ skb_pull(skb, 8); ++#endif ++ skb->dev = dev; ++ skb->protocol = eth_type_trans(skb, dev); ++ netif_receive_skb(skb); ++ priv->stats.rx_packets++; ++ priv->stats.rx_bytes+=len; ++} ++ ++static int xrx200_poll_rx(struct napi_struct *napi, int budget) ++{ ++ struct xrx200_chan *ch = container_of(napi, ++ struct xrx200_chan, napi); ++ struct xrx200_priv *priv = netdev_priv(ch->devs[0]); ++ int rx = 0; ++ int complete = 0; ++ ++ while ((rx < budget) && !complete) { ++ struct ltq_dma_desc *desc = &ch->dma.desc_base[ch->dma.desc]; ++ if ((desc->ctl & (LTQ_DMA_OWN | LTQ_DMA_C)) == LTQ_DMA_C) { ++#ifdef SW_ROUTING ++ struct sk_buff *skb = ch->skb[ch->dma.desc]; ++ u8 *special_tag = (u8*)skb->data; ++ int port = (special_tag[7] >> SPPID_SHIFT) & SPPID_MASK; ++ xrx200_hw_receive(ch, priv->hw->port_map[port]); ++#else ++ xrx200_hw_receive(ch, 0); ++#endif ++ rx++; ++ } else { ++ complete = 1; ++ } ++ } ++ ++ if (complete || !rx) { ++ napi_complete(&ch->napi); ++ ltq_dma_enable_irq(&ch->dma); ++ } ++ ++ return rx; ++} ++ ++static void xrx200_tx_housekeeping(unsigned long ptr) ++{ ++ struct xrx200_chan *ch = (struct xrx200_chan *) ptr; ++ int pkts = 0; ++ int i; ++ ++ spin_lock_bh(&ch->lock); ++ ltq_dma_ack_irq(&ch->dma); ++ while ((ch->dma.desc_base[ch->tx_free].ctl & (LTQ_DMA_OWN | LTQ_DMA_C)) == LTQ_DMA_C) { ++ struct sk_buff *skb = ch->skb[ch->tx_free]; ++ ++ pkts++; ++ ch->skb[ch->tx_free] = NULL; ++ dev_kfree_skb(skb); ++ memset(&ch->dma.desc_base[ch->tx_free], 0, ++ sizeof(struct ltq_dma_desc)); ++ ch->tx_free++; ++ ch->tx_free %= LTQ_DESC_NUM; ++ } ++ ltq_dma_enable_irq(&ch->dma); ++ spin_unlock_bh(&ch->lock); ++ ++ if (!pkts) ++ return; ++ ++ for (i = 0; i < XRX200_MAX_DEV && ch->devs[i]; i++) ++ netif_wake_queue(ch->devs[i]); ++} ++ ++static struct net_device_stats *xrx200_get_stats (struct net_device *dev) ++{ ++ struct xrx200_priv *priv = netdev_priv(dev); ++ ++ return &priv->stats; ++} ++ ++static void xrx200_tx_timeout(struct net_device *dev) ++{ ++ struct xrx200_priv *priv = netdev_priv(dev); ++ ++ printk(KERN_ERR "%s: transmit timed out, disable the dma channel irq\n", dev->name); ++ ++ priv->stats.tx_errors++; ++ netif_wake_queue(dev); ++} ++ ++static int xrx200_start_xmit(struct sk_buff *skb, struct net_device *dev) ++{ ++ struct xrx200_priv *priv = netdev_priv(dev); ++ struct xrx200_chan *ch; ++ struct ltq_dma_desc *desc; ++ u32 byte_offset; ++ int ret = NETDEV_TX_OK; ++ int len; ++#ifdef SW_ROUTING ++ u32 special_tag = (SPID_CPU_PORT << SPID_SHIFT) | DPID_ENABLE; ++#endif ++ if(priv->id) ++ ch = &priv->hw->chan[XRX200_DMA_TX_2]; ++ else ++ ch = &priv->hw->chan[XRX200_DMA_TX]; ++ ++ desc = &ch->dma.desc_base[ch->dma.desc]; ++ ++ skb->dev = dev; ++ len = skb->len < ETH_ZLEN ? ETH_ZLEN : skb->len; ++ ++#ifdef SW_ROUTING ++ if (is_multicast_ether_addr(eth_hdr(skb)->h_dest)) { ++ u16 port_map = priv->port_map; ++ ++ if (priv->sw && skb->protocol == htons(ETH_P_8021Q)) { ++ u16 vid; ++ int i; ++ ++ port_map = 0; ++ if (!__vlan_get_tag(skb, &vid)) { ++ for (i = 0; i < XRX200_MAX_VLAN; i++) { ++ if (priv->hw->vlan_vid[i] != vid) ++ continue; ++ port_map = priv->hw->vlan_port_map[i]; ++ break; ++ } ++ } ++ } ++ ++ special_tag |= (port_map << PORT_MAP_SHIFT) | ++ PORT_MAP_SEL | PORT_MAP_EN; ++ } ++ if(priv->wan) ++ special_tag |= (1 << DPID_SHIFT); ++ if(skb_headroom(skb) < 4) { ++ struct sk_buff *tmp = skb_realloc_headroom(skb, 4); ++ dev_kfree_skb_any(skb); ++ skb = tmp; ++ } ++ skb_push(skb, 4); ++ memcpy(skb->data, &special_tag, sizeof(u32)); ++ len += 4; ++#endif ++ ++ /* dma needs to start on a 16 byte aligned address */ ++ byte_offset = CPHYSADDR(skb->data) % 16; ++ ++ spin_lock_bh(&ch->lock); ++ if ((desc->ctl & (LTQ_DMA_OWN | LTQ_DMA_C)) || ch->skb[ch->dma.desc]) { ++ netdev_err(dev, "tx ring full\n"); ++ netif_stop_queue(dev); ++ ret = NETDEV_TX_BUSY; ++ goto out; ++ } ++ ++ ch->skb[ch->dma.desc] = skb; ++ ++ netif_trans_update(dev); ++ ++ desc->addr = ((unsigned int) dma_map_single(NULL, skb->data, len, ++ DMA_TO_DEVICE)) - byte_offset; ++ wmb(); ++ desc->ctl = LTQ_DMA_OWN | LTQ_DMA_SOP | LTQ_DMA_EOP | ++ LTQ_DMA_TX_OFFSET(byte_offset) | (len & LTQ_DMA_SIZE_MASK); ++ ch->dma.desc++; ++ ch->dma.desc %= LTQ_DESC_NUM; ++ if (ch->dma.desc == ch->tx_free) ++ netif_stop_queue(dev); ++ ++ ++ priv->stats.tx_packets++; ++ priv->stats.tx_bytes+=len; ++ ++out: ++ spin_unlock_bh(&ch->lock); ++ ++ return ret; ++} ++ ++static irqreturn_t xrx200_dma_irq(int irq, void *priv) ++{ ++ struct xrx200_hw *hw = priv; ++ int chnr = irq - XRX200_DMA_IRQ; ++ struct xrx200_chan *ch = &hw->chan[chnr]; ++ ++ ltq_dma_disable_irq(&ch->dma); ++ ltq_dma_ack_irq(&ch->dma); ++ ++ if (chnr % 2) ++ tasklet_schedule(&ch->tasklet); ++ else ++ napi_schedule(&ch->napi); ++ ++ return IRQ_HANDLED; ++} ++ ++static int xrx200_dma_init(struct xrx200_hw *hw) ++{ ++ int i, err = 0; ++ ++ ltq_dma_init_port(DMA_PORT_ETOP); ++ ++ for (i = 0; i < 8 && !err; i++) { ++ int irq = XRX200_DMA_IRQ + i; ++ struct xrx200_chan *ch = &hw->chan[i]; ++ ++ spin_lock_init(&ch->lock); ++ ++ ch->idx = ch->dma.nr = i; ++ ++ if (i == XRX200_DMA_TX) { ++ ltq_dma_alloc_tx(&ch->dma); ++ err = request_irq(irq, xrx200_dma_irq, 0, "vrx200_tx", hw); ++ } else if (i == XRX200_DMA_TX_2) { ++ ltq_dma_alloc_tx(&ch->dma); ++ err = request_irq(irq, xrx200_dma_irq, 0, "vrx200_tx_2", hw); ++ } else if (i == XRX200_DMA_RX) { ++ ltq_dma_alloc_rx(&ch->dma); ++ for (ch->dma.desc = 0; ch->dma.desc < LTQ_DESC_NUM; ++ ch->dma.desc++) ++ if (xrx200_alloc_skb(ch)) ++ err = -ENOMEM; ++ ch->dma.desc = 0; ++ err = request_irq(irq, xrx200_dma_irq, 0, "vrx200_rx", hw); ++ } else ++ continue; ++ ++ if (!err) ++ ch->dma.irq = irq; ++ else ++ pr_err("net-xrx200: failed to request irq %d\n", irq); ++ } ++ ++ return err; ++} ++ ++#ifdef SW_POLLING ++static void xrx200_gmac_update(struct xrx200_port *port) ++{ ++ u16 phyaddr = port->phydev->mdio.addr & MDIO_PHY_ADDR_MASK; ++ u16 miimode = ltq_mii_r32(MII_CFG(port->num)) & MII_CFG_MODE_MASK; ++ u16 miirate = 0; ++ ++ switch (port->phydev->speed) { ++ case SPEED_1000: ++ phyaddr |= MDIO_PHY_SPEED_G1; ++ miirate = MII_CFG_RATE_M125; ++ break; ++ ++ case SPEED_100: ++ phyaddr |= MDIO_PHY_SPEED_M100; ++ switch (miimode) { ++ case MII_CFG_MODE_RMIIM: ++ case MII_CFG_MODE_RMIIP: ++ miirate = MII_CFG_RATE_M50; ++ break; ++ default: ++ miirate = MII_CFG_RATE_M25; ++ break; ++ } ++ break; ++ ++ default: ++ phyaddr |= MDIO_PHY_SPEED_M10; ++ miirate = MII_CFG_RATE_M2P5; ++ break; ++ } ++ ++ if (port->phydev->link) ++ phyaddr |= MDIO_PHY_LINK_UP; ++ else ++ phyaddr |= MDIO_PHY_LINK_DOWN; ++ ++ if (port->phydev->duplex == DUPLEX_FULL) ++ phyaddr |= MDIO_PHY_FDUP_EN; ++ else ++ phyaddr |= MDIO_PHY_FDUP_DIS; ++ ++ ltq_mdio_w32_mask(MDIO_UPDATE_MASK, phyaddr, MDIO_PHY(port->num)); ++ ltq_mii_w32_mask(MII_CFG_RATE_MASK, miirate, MII_CFG(port->num)); ++ udelay(1); ++} ++#else ++static void xrx200_gmac_update(struct xrx200_port *port) ++{ ++ ++} ++#endif ++ ++static void xrx200_mdio_link(struct net_device *dev) ++{ ++ struct xrx200_priv *priv = netdev_priv(dev); ++ int i; ++ ++ for (i = 0; i < priv->num_port; i++) { ++ if (!priv->port[i].phydev) ++ continue; ++ ++ if (priv->port[i].link != priv->port[i].phydev->link) { ++ xrx200_gmac_update(&priv->port[i]); ++ priv->port[i].link = priv->port[i].phydev->link; ++ netdev_info(dev, "port %d %s link\n", ++ priv->port[i].num, ++ (priv->port[i].link)?("got"):("lost")); ++ } ++ } ++} ++ ++static inline int xrx200_mdio_poll(struct mii_bus *bus) ++{ ++ unsigned cnt = 10000; ++ ++ while (likely(cnt--)) { ++ unsigned ctrl = ltq_mdio_r32(MDIO_CTRL); ++ if ((ctrl & MDIO_BUSY) == 0) ++ return 0; ++ } ++ ++ return 1; ++} ++ ++static int xrx200_mdio_wr(struct mii_bus *bus, int addr, int reg, u16 val) ++{ ++ if (xrx200_mdio_poll(bus)) ++ return 1; ++ ++ ltq_mdio_w32(val, MDIO_WRITE); ++ ltq_mdio_w32(MDIO_BUSY | MDIO_WR | ++ ((addr & MDIO_MASK) << MDIO_ADDRSHIFT) | ++ (reg & MDIO_MASK), ++ MDIO_CTRL); ++ ++ return 0; ++} ++ ++static int xrx200_mdio_rd(struct mii_bus *bus, int addr, int reg) ++{ ++ if (xrx200_mdio_poll(bus)) ++ return -1; ++ ++ ltq_mdio_w32(MDIO_BUSY | MDIO_RD | ++ ((addr & MDIO_MASK) << MDIO_ADDRSHIFT) | ++ (reg & MDIO_MASK), ++ MDIO_CTRL); ++ ++ if (xrx200_mdio_poll(bus)) ++ return -1; ++ ++ return ltq_mdio_r32(MDIO_READ); ++} ++ ++static int xrx200_phy_has_link(struct net_device *dev) ++{ ++ struct xrx200_priv *priv = netdev_priv(dev); ++ int i; ++ ++ for (i = 0; i < priv->num_port; i++) { ++ if (!priv->port[i].phydev) ++ continue; ++ ++ if (priv->port[i].phydev->link) ++ return 1; ++ } ++ ++ return 0; ++} ++ ++static void xrx200_phy_link_change(struct phy_device *phydev, bool up, bool do_carrier) ++{ ++ struct net_device *netdev = phydev->attached_dev; ++ ++ if (do_carrier) ++ if (up) ++ netif_carrier_on(netdev); ++ else if (!xrx200_phy_has_link(netdev)) ++ netif_carrier_off(netdev); ++ ++ phydev->adjust_link(netdev); ++} ++ ++static int xrx200_mdio_probe(struct net_device *dev, struct xrx200_port *port) ++{ ++ struct xrx200_priv *priv = netdev_priv(dev); ++ struct phy_device *phydev = NULL; ++ unsigned val; ++ ++ phydev = mdiobus_get_phy(priv->hw->mii_bus, port->phy_addr); ++ ++ if (!phydev) { ++ netdev_err(dev, "no PHY found\n"); ++ return -ENODEV; ++ } ++ ++ phydev = phy_connect(dev, phydev_name(phydev), &xrx200_mdio_link, ++ port->phy_if); ++ ++ if (IS_ERR(phydev)) { ++ netdev_err(dev, "Could not attach to PHY\n"); ++ return PTR_ERR(phydev); ++ } ++ ++ phydev->supported &= (SUPPORTED_10baseT_Half ++ | SUPPORTED_10baseT_Full ++ | SUPPORTED_100baseT_Half ++ | SUPPORTED_100baseT_Full ++ | SUPPORTED_1000baseT_Half ++ | SUPPORTED_1000baseT_Full ++ | SUPPORTED_Autoneg ++ | SUPPORTED_MII ++ | SUPPORTED_TP); ++ phydev->advertising = phydev->supported; ++ port->phydev = phydev; ++ phydev->phy_link_change = xrx200_phy_link_change; ++ ++ phy_attached_info(phydev); ++ ++#ifdef SW_POLLING ++ phy_read_status(phydev); ++ ++ val = xrx200_mdio_rd(priv->hw->mii_bus, MDIO_DEVAD_NONE, MII_CTRL1000); ++ val |= ADVERTIZE_MPD; ++ xrx200_mdio_wr(priv->hw->mii_bus, MDIO_DEVAD_NONE, MII_CTRL1000, val); ++ xrx200_mdio_wr(priv->hw->mii_bus, 0, 0, 0x1040); ++ ++ phy_start_aneg(phydev); ++#endif ++ return 0; ++} ++ ++static void xrx200_port_config(struct xrx200_priv *priv, ++ const struct xrx200_port *port) ++{ ++ u16 miimode = 0; ++ ++ switch (port->num) { ++ case 0: /* xMII0 */ ++ case 1: /* xMII1 */ ++ switch (port->phy_if) { ++ case PHY_INTERFACE_MODE_MII: ++ if (port->flags & XRX200_PORT_TYPE_PHY) ++ /* MII MAC mode, connected to external PHY */ ++ miimode = MII_CFG_MODE_MIIM; ++ else ++ /* MII PHY mode, connected to external MAC */ ++ miimode = MII_CFG_MODE_MIIP; ++ break; ++ case PHY_INTERFACE_MODE_RMII: ++ if (port->flags & XRX200_PORT_TYPE_PHY) ++ /* RMII MAC mode, connected to external PHY */ ++ miimode = MII_CFG_MODE_RMIIM; ++ else ++ /* RMII PHY mode, connected to external MAC */ ++ miimode = MII_CFG_MODE_RMIIP; ++ break; ++ case PHY_INTERFACE_MODE_RGMII: ++ /* RGMII MAC mode, connected to external PHY */ ++ miimode = MII_CFG_MODE_RGMII; ++ break; ++ default: ++ break; ++ } ++ break; ++ case 2: /* internal GPHY0 */ ++ case 3: /* internal GPHY0 */ ++ case 4: /* internal GPHY1 */ ++ switch (port->phy_if) { ++ case PHY_INTERFACE_MODE_MII: ++ case PHY_INTERFACE_MODE_GMII: ++ /* MII MAC mode, connected to internal GPHY */ ++ miimode = MII_CFG_MODE_MIIM; ++ break; ++ default: ++ break; ++ } ++ break; ++ case 5: /* internal GPHY1 or xMII2 */ ++ switch (port->phy_if) { ++ case PHY_INTERFACE_MODE_MII: ++ /* MII MAC mode, connected to internal GPHY */ ++ miimode = MII_CFG_MODE_MIIM; ++ break; ++ case PHY_INTERFACE_MODE_RGMII: ++ /* RGMII MAC mode, connected to external PHY */ ++ miimode = MII_CFG_MODE_RGMII; ++ break; ++ default: ++ break; ++ } ++ break; ++ default: ++ break; ++ } ++ ++ ltq_mii_w32_mask(MII_CFG_MODE_MASK, miimode | MII_CFG_EN, ++ MII_CFG(port->num)); ++} ++ ++static int xrx200_init(struct net_device *dev) ++{ ++ struct xrx200_priv *priv = netdev_priv(dev); ++ struct sockaddr mac; ++ int err, i; ++ ++#ifndef SW_POLLING ++ unsigned int reg = 0; ++ ++ /* enable auto polling */ ++ for (i = 0; i < priv->num_port; i++) ++ reg |= BIT(priv->port[i].num); ++ ltq_mdio_w32(reg, MDIO_CLK_CFG0); ++ ltq_mdio_w32(MDIO1_25MHZ, MDIO_CLK_CFG1); ++#endif ++ ++ /* setup each port */ ++ for (i = 0; i < priv->num_port; i++) ++ xrx200_port_config(priv, &priv->port[i]); ++ ++ memcpy(&mac.sa_data, priv->mac, ETH_ALEN); ++ if (!is_valid_ether_addr(mac.sa_data)) { ++ pr_warn("net-xrx200: invalid MAC, using random\n"); ++ eth_random_addr(mac.sa_data); ++ dev->addr_assign_type |= NET_ADDR_RANDOM; ++ } ++ ++ err = eth_mac_addr(dev, &mac); ++ if (err) ++ goto err_netdev; ++ ++ for (i = 0; i < priv->num_port; i++) ++ if (xrx200_mdio_probe(dev, &priv->port[i])) ++ pr_warn("xrx200-mdio: probing phy of port %d failed\n", ++ priv->port[i].num); ++ ++ return 0; ++ ++err_netdev: ++ unregister_netdev(dev); ++ free_netdev(dev); ++ return err; ++} ++ ++static void xrx200_pci_microcode(void) ++{ ++ int i; ++ ++ ltq_switch_w32_mask(PCE_TBL_CFG_ADDR_MASK | PCE_TBL_CFG_ADWR_MASK, ++ PCE_TBL_CFG_ADWR, PCE_TBL_CTRL); ++ ltq_switch_w32(0, PCE_TBL_MASK); ++ ++ for (i = 0; i < ARRAY_SIZE(pce_microcode); i++) { ++ ltq_switch_w32(i, PCE_TBL_ADDR); ++ ltq_switch_w32(pce_microcode[i].val[3], PCE_TBL_VAL(0)); ++ ltq_switch_w32(pce_microcode[i].val[2], PCE_TBL_VAL(1)); ++ ltq_switch_w32(pce_microcode[i].val[1], PCE_TBL_VAL(2)); ++ ltq_switch_w32(pce_microcode[i].val[0], PCE_TBL_VAL(3)); ++ ++ // start the table access: ++ ltq_switch_w32_mask(0, PCE_TBL_BUSY, PCE_TBL_CTRL); ++ while (ltq_switch_r32(PCE_TBL_CTRL) & PCE_TBL_BUSY); ++ } ++ ++ /* tell the switch that the microcode is loaded */ ++ ltq_switch_w32_mask(0, BIT(3), PCE_GCTRL_REG(0)); ++} ++ ++static void xrx200_hw_init(struct xrx200_hw *hw) ++{ ++ int i; ++ ++ /* enable clock gate */ ++ clk_enable(hw->clk); ++ ++ ltq_switch_w32(1, 0); ++ mdelay(100); ++ ltq_switch_w32(0, 0); ++ /* ++ * TODO: we should really disbale all phys/miis here and explicitly ++ * enable them in the device secific init function ++ */ ++ ++ /* disable port fetch/store dma */ ++ for (i = 0; i < 7; i++ ) { ++ ltq_switch_w32(0, FDMA_PCTRLx(i)); ++ ltq_switch_w32(0, SDMA_PCTRLx(i)); ++ } ++ ++ /* enable Switch */ ++ ltq_mdio_w32_mask(0, MDIO_GLOB_ENABLE, MDIO_GLOB); ++ ++ /* load the pce microcode */ ++ xrx200_pci_microcode(); ++ ++ /* Default unknown Broadcat/Multicast/Unicast port maps */ ++ ltq_switch_w32(0x40, PCE_PMAP1); ++ ltq_switch_w32(0x40, PCE_PMAP2); ++ ltq_switch_w32(0x40, PCE_PMAP3); ++ ++ /* RMON Counter Enable for all physical ports */ ++ for (i = 0; i < 7; i++) ++ ltq_switch_w32(0x1, BM_PCFG(i)); ++ ++ /* disable auto polling */ ++ ltq_mdio_w32(0x0, MDIO_CLK_CFG0); ++ ++ /* enable port statistic counters */ ++ for (i = 0; i < 7; i++) ++ ltq_switch_w32(0x1, BM_PCFGx(i)); ++ ++ /* set IPG to 12 */ ++ ltq_pmac_w32_mask(PMAC_IPG_MASK, 0xb, PMAC_RX_IPG); ++ ++#ifdef SW_ROUTING ++ /* enable status header, enable CRC */ ++ ltq_pmac_w32_mask(0, ++ PMAC_HD_CTL_RST | PMAC_HD_CTL_AST | PMAC_HD_CTL_RXSH | PMAC_HD_CTL_AS | PMAC_HD_CTL_AC | PMAC_HD_CTL_RC, ++ PMAC_HD_CTL); ++#else ++ /* disable status header, enable CRC */ ++ ltq_pmac_w32_mask(PMAC_HD_CTL_AST | PMAC_HD_CTL_RXSH | PMAC_HD_CTL_AS, ++ PMAC_HD_CTL_AC | PMAC_HD_CTL_RC, ++ PMAC_HD_CTL); ++#endif ++ ++ /* enable port fetch/store dma & VLAN Modification */ ++ for (i = 0; i < 7; i++ ) { ++ ltq_switch_w32_mask(0, 0x19, FDMA_PCTRLx(i)); ++ ltq_switch_w32_mask(0, 0x01, SDMA_PCTRLx(i)); ++ ltq_switch_w32_mask(0, PCE_INGRESS, PCE_PCTRL_REG(i, 0)); ++ } ++ ++ /* enable special tag insertion on cpu port */ ++ ltq_switch_w32_mask(0, 0x02, FDMA_PCTRLx(6)); ++ ltq_switch_w32_mask(0, PCE_INGRESS, PCE_PCTRL_REG(6, 0)); ++ ltq_switch_w32_mask(0, BIT(3), MAC_CTRL_REG(6, 2)); ++ ltq_switch_w32(1518 + 8 + 4 * 2, MAC_FLEN_REG); ++ xrx200sw_write_x(1, XRX200_BM_QUEUE_GCTRL_GL_MOD, 0); ++ ++ for (i = 0; i < XRX200_MAX_VLAN; i++) ++ hw->vlan_vid[i] = i; ++} ++ ++static void xrx200_hw_cleanup(struct xrx200_hw *hw) ++{ ++ int i; ++ ++ /* disable the switch */ ++ ltq_mdio_w32_mask(MDIO_GLOB_ENABLE, 0, MDIO_GLOB); ++ ++ /* free the channels and IRQs */ ++ for (i = 0; i < 2; i++) { ++ ltq_dma_free(&hw->chan[i].dma); ++ if (hw->chan[i].dma.irq) ++ free_irq(hw->chan[i].dma.irq, hw); ++ } ++ ++ /* free the allocated RX ring */ ++ for (i = 0; i < LTQ_DESC_NUM; i++) ++ dev_kfree_skb_any(hw->chan[XRX200_DMA_RX].skb[i]); ++ ++ /* clear the mdio bus */ ++ mdiobus_unregister(hw->mii_bus); ++ mdiobus_free(hw->mii_bus); ++ ++ /* release the clock */ ++ clk_disable(hw->clk); ++ clk_put(hw->clk); ++} ++ ++static int xrx200_of_mdio(struct xrx200_hw *hw, struct device_node *np) ++{ ++ hw->mii_bus = mdiobus_alloc(); ++ if (!hw->mii_bus) ++ return -ENOMEM; ++ ++ hw->mii_bus->read = xrx200_mdio_rd; ++ hw->mii_bus->write = xrx200_mdio_wr; ++ hw->mii_bus->name = "lantiq,xrx200-mdio"; ++ snprintf(hw->mii_bus->id, MII_BUS_ID_SIZE, "%x", 0); ++ ++ if (of_mdiobus_register(hw->mii_bus, np)) { ++ mdiobus_free(hw->mii_bus); ++ return -ENXIO; ++ } ++ ++ return 0; ++} ++ ++static void xrx200_of_port(struct xrx200_priv *priv, struct device_node *port) ++{ ++ const __be32 *addr, *id = of_get_property(port, "reg", NULL); ++ struct xrx200_port *p = &priv->port[priv->num_port]; ++ ++ if (!id) ++ return; ++ ++ memset(p, 0, sizeof(struct xrx200_port)); ++ p->phy_node = of_parse_phandle(port, "phy-handle", 0); ++ addr = of_get_property(p->phy_node, "reg", NULL); ++ if (!addr) ++ return; ++ ++ p->num = *id; ++ p->phy_addr = *addr; ++ p->phy_if = of_get_phy_mode(port); ++ if (p->phy_addr > 0x10) ++ p->flags = XRX200_PORT_TYPE_MAC; ++ else ++ p->flags = XRX200_PORT_TYPE_PHY; ++ priv->num_port++; ++ ++ p->gpio = of_get_gpio_flags(port, 0, &p->gpio_flags); ++ if (gpio_is_valid(p->gpio)) ++ if (!gpio_request(p->gpio, "phy-reset")) { ++ gpio_direction_output(p->gpio, ++ (p->gpio_flags & OF_GPIO_ACTIVE_LOW) ? (1) : (0)); ++ udelay(100); ++ gpio_set_value(p->gpio, (p->gpio_flags & OF_GPIO_ACTIVE_LOW) ? (0) : (1)); ++ } ++ /* is this port a wan port ? */ ++ if (priv->wan) ++ priv->hw->wan_map |= BIT(p->num); ++ ++ priv->port_map |= BIT(p->num); ++ ++ /* store the port id in the hw struct so we can map ports -> devices */ ++ priv->hw->port_map[p->num] = priv->hw->num_devs; ++} ++ ++static const struct net_device_ops xrx200_netdev_ops = { ++ .ndo_init = xrx200_init, ++ .ndo_open = xrx200_open, ++ .ndo_stop = xrx200_close, ++ .ndo_start_xmit = xrx200_start_xmit, ++ .ndo_set_mac_address = eth_mac_addr, ++ .ndo_validate_addr = eth_validate_addr, ++ .ndo_get_stats = xrx200_get_stats, ++ .ndo_tx_timeout = xrx200_tx_timeout, ++}; ++ ++static void xrx200_of_iface(struct xrx200_hw *hw, struct device_node *iface, struct device *dev) ++{ ++ struct xrx200_priv *priv; ++ struct device_node *port; ++ const __be32 *wan; ++ const u8 *mac; ++ ++ /* alloc the network device */ ++ hw->devs[hw->num_devs] = alloc_etherdev(sizeof(struct xrx200_priv)); ++ if (!hw->devs[hw->num_devs]) ++ return; ++ ++ /* setup the network device */ ++ strcpy(hw->devs[hw->num_devs]->name, "eth%d"); ++ hw->devs[hw->num_devs]->netdev_ops = &xrx200_netdev_ops; ++ hw->devs[hw->num_devs]->watchdog_timeo = XRX200_TX_TIMEOUT; ++ hw->devs[hw->num_devs]->needed_headroom = XRX200_HEADROOM; ++ SET_NETDEV_DEV(hw->devs[hw->num_devs], dev); ++ ++ /* setup our private data */ ++ priv = netdev_priv(hw->devs[hw->num_devs]); ++ priv->hw = hw; ++ priv->id = hw->num_devs; ++ ++ mac = of_get_mac_address(iface); ++ if (mac) ++ memcpy(priv->mac, mac, ETH_ALEN); ++ ++ /* is this the wan interface ? */ ++ wan = of_get_property(iface, "lantiq,wan", NULL); ++ if (wan && (*wan == 1)) ++ priv->wan = 1; ++ ++ /* should the switch be enabled on this interface ? */ ++ if (of_find_property(iface, "lantiq,switch", NULL)) ++ priv->sw = 1; ++ ++ /* load the ports that are part of the interface */ ++ for_each_child_of_node(iface, port) ++ if (of_device_is_compatible(port, "lantiq,xrx200-pdi-port")) ++ xrx200_of_port(priv, port); ++ ++ /* register the actual device */ ++ if (!register_netdev(hw->devs[hw->num_devs])) ++ hw->num_devs++; ++} ++ ++static struct xrx200_hw xrx200_hw; ++ ++static int xrx200_probe(struct platform_device *pdev) ++{ ++ struct resource *res[4]; ++ struct device_node *mdio_np, *iface_np, *phy_np; ++ struct of_phandle_iterator it; ++ int err; ++ int i; ++ ++ /* load the memory ranges */ ++ for (i = 0; i < 4; i++) { ++ res[i] = platform_get_resource(pdev, IORESOURCE_MEM, i); ++ if (!res[i]) { ++ dev_err(&pdev->dev, "failed to get resources\n"); ++ return -ENOENT; ++ } ++ } ++ xrx200_switch_membase = devm_ioremap_resource(&pdev->dev, res[0]); ++ xrx200_mdio_membase = devm_ioremap_resource(&pdev->dev, res[1]); ++ xrx200_mii_membase = devm_ioremap_resource(&pdev->dev, res[2]); ++ xrx200_pmac_membase = devm_ioremap_resource(&pdev->dev, res[3]); ++ if (!xrx200_switch_membase || !xrx200_mdio_membase || ++ !xrx200_mii_membase || !xrx200_pmac_membase) { ++ dev_err(&pdev->dev, "failed to request and remap io ranges \n"); ++ return -ENOMEM; ++ } ++ ++ of_for_each_phandle(&it, err, pdev->dev.of_node, "lantiq,phys", NULL, 0) { ++ phy_np = it.node; ++ if (phy_np) { ++ struct platform_device *phy = of_find_device_by_node(phy_np); ++ ++ of_node_put(phy_np); ++ if (!platform_get_drvdata(phy)) ++ return -EPROBE_DEFER; ++ } ++ } ++ ++ /* get the clock */ ++ xrx200_hw.clk = clk_get(&pdev->dev, NULL); ++ if (IS_ERR(xrx200_hw.clk)) { ++ dev_err(&pdev->dev, "failed to get clock\n"); ++ return PTR_ERR(xrx200_hw.clk); ++ } ++ ++ /* bring up the dma engine and IP core */ ++ xrx200_dma_init(&xrx200_hw); ++ xrx200_hw_init(&xrx200_hw); ++ tasklet_init(&xrx200_hw.chan[XRX200_DMA_TX].tasklet, xrx200_tx_housekeeping, (u32) &xrx200_hw.chan[XRX200_DMA_TX]); ++ tasklet_init(&xrx200_hw.chan[XRX200_DMA_TX_2].tasklet, xrx200_tx_housekeeping, (u32) &xrx200_hw.chan[XRX200_DMA_TX_2]); ++ ++ /* bring up the mdio bus */ ++ mdio_np = of_find_compatible_node(pdev->dev.of_node, NULL, ++ "lantiq,xrx200-mdio"); ++ if (mdio_np) ++ if (xrx200_of_mdio(&xrx200_hw, mdio_np)) ++ dev_err(&pdev->dev, "mdio probe failed\n"); ++ ++ /* load the interfaces */ ++ for_each_child_of_node(pdev->dev.of_node, iface_np) ++ if (of_device_is_compatible(iface_np, "lantiq,xrx200-pdi")) { ++ if (xrx200_hw.num_devs < XRX200_MAX_DEV) ++ xrx200_of_iface(&xrx200_hw, iface_np, &pdev->dev); ++ else ++ dev_err(&pdev->dev, ++ "only %d interfaces allowed\n", ++ XRX200_MAX_DEV); ++ } ++ ++ if (!xrx200_hw.num_devs) { ++ xrx200_hw_cleanup(&xrx200_hw); ++ dev_err(&pdev->dev, "failed to load interfaces\n"); ++ return -ENOENT; ++ } ++ ++ xrx200sw_init(&xrx200_hw); ++ ++ /* set wan port mask */ ++ ltq_pmac_w32(xrx200_hw.wan_map, PMAC_EWAN); ++ ++ for (i = 0; i < xrx200_hw.num_devs; i++) { ++ xrx200_hw.chan[XRX200_DMA_RX].devs[i] = xrx200_hw.devs[i]; ++ xrx200_hw.chan[XRX200_DMA_TX].devs[i] = xrx200_hw.devs[i]; ++ xrx200_hw.chan[XRX200_DMA_TX_2].devs[i] = xrx200_hw.devs[i]; ++ } ++ ++ /* setup NAPI */ ++ init_dummy_netdev(&xrx200_hw.chan[XRX200_DMA_RX].dummy_dev); ++ netif_napi_add(&xrx200_hw.chan[XRX200_DMA_RX].dummy_dev, ++ &xrx200_hw.chan[XRX200_DMA_RX].napi, xrx200_poll_rx, 32); ++ ++ platform_set_drvdata(pdev, &xrx200_hw); ++ ++ return 0; ++} ++ ++static int xrx200_remove(struct platform_device *pdev) ++{ ++ struct net_device *dev = platform_get_drvdata(pdev); ++ struct xrx200_priv *priv; ++ ++ if (!dev) ++ return 0; ++ ++ priv = netdev_priv(dev); ++ ++ /* free stack related instances */ ++ netif_stop_queue(dev); ++ netif_napi_del(&xrx200_hw.chan[XRX200_DMA_RX].napi); ++ ++ /* shut down hardware */ ++ xrx200_hw_cleanup(&xrx200_hw); ++ ++ /* remove the actual device */ ++ unregister_netdev(dev); ++ free_netdev(dev); ++ ++ return 0; ++} ++ ++static const struct of_device_id xrx200_match[] = { ++ { .compatible = "lantiq,xrx200-net" }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, xrx200_match); ++ ++static struct platform_driver xrx200_driver = { ++ .probe = xrx200_probe, ++ .remove = xrx200_remove, ++ .driver = { ++ .name = "lantiq,xrx200-net", ++ .of_match_table = xrx200_match, ++ .owner = THIS_MODULE, ++ }, ++}; ++ ++module_platform_driver(xrx200_driver); ++ ++MODULE_AUTHOR("John Crispin "); ++MODULE_DESCRIPTION("Lantiq SoC XRX200 ethernet"); ++MODULE_LICENSE("GPL"); +--- /dev/null ++++ b/drivers/net/ethernet/lantiq_xrx200_sw.h +@@ -0,0 +1,1328 @@ ++/* ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms of the GNU General Public License version 2 as published ++ * by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ * ++ * You should have received a copy of the GNU General Public License ++ * along with this program; if not, write to the Free Software ++ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307, USA. ++ * ++ * Copyright (C) 2010 Lantiq Deutschland GmbH ++ * Copyright (C) 2013 Antonios Vamporakis ++ * ++ * VR9 switch registers extracted from 310TUJ0 switch api ++ * WARNING mult values of 0x00 may not be correct ++ * ++ */ ++ ++enum { ++// XRX200_ETHSW_SWRES, /* Ethernet Switch ResetControl Register */ ++// XRX200_ETHSW_SWRES_R1, /* Hardware Reset */ ++// XRX200_ETHSW_SWRES_R0, /* Register Configuration */ ++// XRX200_ETHSW_CLK_MAC_GAT, /* Ethernet Switch Clock ControlRegister */ ++// XRX200_ETHSW_CLK_EXP_SLEEP, /* Exponent to put system into sleep */ ++// XRX200_ETHSW_CLK_EXP_WAKE, /* Exponent to wake up system */ ++// XRX200_ETHSW_CLK_CLK2_EN, /* CLK2 Input for MAC */ ++// XRX200_ETHSW_CLK_EXT_DIV_EN, /* External Clock Divider Enable */ ++// XRX200_ETHSW_CLK_RAM_DBG_EN, /* Clock Gating Enable */ ++// XRX200_ETHSW_CLK_REG_GAT_EN, /* Clock Gating Enable */ ++// XRX200_ETHSW_CLK_GAT_EN, /* Clock Gating Enable */ ++// XRX200_ETHSW_CLK_MAC_GAT_EN, /* Clock Gating Enable */ ++// XRX200_ETHSW_DBG_STEP, /* Ethernet Switch Debug ControlRegister */ ++// XRX200_ETHSW_DBG_CLK_SEL, /* Trigger Enable */ ++// XRX200_ETHSW_DBG_MON_EN, /* Monitoring Enable */ ++// XRX200_ETHSW_DBG_TRIG_EN, /* Trigger Enable */ ++// XRX200_ETHSW_DBG_MODE, /* Debug Mode */ ++// XRX200_ETHSW_DBG_STEP_TIME, /* Clock Step Size */ ++// XRX200_ETHSW_SSB_MODE, /* Ethernet Switch SharedSegment Buffer Mode Register */ ++// XRX200_ETHSW_SSB_MODE_ADDE, /* Memory Address */ ++// XRX200_ETHSW_SSB_MODE_MODE, /* Memory Access Mode */ ++// XRX200_ETHSW_SSB_ADDR, /* Ethernet Switch SharedSegment Buffer Address Register */ ++// XRX200_ETHSW_SSB_ADDR_ADDE, /* Memory Address */ ++// XRX200_ETHSW_SSB_DATA, /* Ethernet Switch SharedSegment Buffer Data Register */ ++// XRX200_ETHSW_SSB_DATA_DATA, /* Data Value */ ++// XRX200_ETHSW_CAP_0, /* Ethernet Switch CapabilityRegister 0 */ ++// XRX200_ETHSW_CAP_0_SPEED, /* Clock frequency */ ++// XRX200_ETHSW_CAP_1, /* Ethernet Switch CapabilityRegister 1 */ ++// XRX200_ETHSW_CAP_1_GMAC, /* MAC operation mode */ ++// XRX200_ETHSW_CAP_1_QUEUE, /* Number of queues */ ++// XRX200_ETHSW_CAP_1_VPORTS, /* Number of virtual ports */ ++// XRX200_ETHSW_CAP_1_PPORTS, /* Number of physical ports */ ++// XRX200_ETHSW_CAP_2, /* Ethernet Switch CapabilityRegister 2 */ ++// XRX200_ETHSW_CAP_2_PACKETS, /* Number of packets */ ++// XRX200_ETHSW_CAP_3, /* Ethernet Switch CapabilityRegister 3 */ ++// XRX200_ETHSW_CAP_3_METERS, /* Number of traffic meters */ ++// XRX200_ETHSW_CAP_3_SHAPERS, /* Number of traffic shapers */ ++// XRX200_ETHSW_CAP_4, /* Ethernet Switch CapabilityRegister 4 */ ++// XRX200_ETHSW_CAP_4_PPPOE, /* PPPoE table size */ ++// XRX200_ETHSW_CAP_4_VLAN, /* Active VLAN table size */ ++// XRX200_ETHSW_CAP_5, /* Ethernet Switch CapabilityRegister 5 */ ++// XRX200_ETHSW_CAP_5_IPPLEN, /* IP packet length table size */ ++// XRX200_ETHSW_CAP_5_PROT, /* Protocol table size */ ++// XRX200_ETHSW_CAP_6, /* Ethernet Switch CapabilityRegister 6 */ ++// XRX200_ETHSW_CAP_6_MACDASA, /* MAC DA/SA table size */ ++// XRX200_ETHSW_CAP_6_APPL, /* Application table size */ ++// XRX200_ETHSW_CAP_7, /* Ethernet Switch CapabilityRegister 7 */ ++// XRX200_ETHSW_CAP_7_IPDASAM, /* IP DA/SA MSB table size */ ++// XRX200_ETHSW_CAP_7_IPDASAL, /* IP DA/SA LSB table size */ ++// XRX200_ETHSW_CAP_8, /* Ethernet Switch CapabilityRegister 8 */ ++// XRX200_ETHSW_CAP_8_MCAST, /* Multicast table size */ ++// XRX200_ETHSW_CAP_9, /* Ethernet Switch CapabilityRegister 9 */ ++// XRX200_ETHSW_CAP_9_FLAGG, /* Flow Aggregation table size */ ++// XRX200_ETHSW_CAP_10, /* Ethernet Switch CapabilityRegister 10 */ ++// XRX200_ETHSW_CAP_10_MACBT, /* MAC bridging table size */ ++// XRX200_ETHSW_CAP_11, /* Ethernet Switch CapabilityRegister 11 */ ++// XRX200_ETHSW_CAP_11_BSIZEL, /* Packet buffer size (lower part, in byte) */ ++// XRX200_ETHSW_CAP_12, /* Ethernet Switch CapabilityRegister 12 */ ++// XRX200_ETHSW_CAP_12_BSIZEH, /* Packet buffer size (higher part, in byte) */ ++// XRX200_ETHSW_VERSION_REV, /* Ethernet Switch VersionRegister */ ++// XRX200_ETHSW_VERSION_MOD_ID, /* Module Identification */ ++// XRX200_ETHSW_VERSION_REV_ID, /* Hardware Revision Identification */ ++// XRX200_ETHSW_IER, /* Interrupt Enable Register */ ++// XRX200_ETHSW_IER_FDMAIE, /* Fetch DMA Interrupt Enable */ ++// XRX200_ETHSW_IER_SDMAIE, /* Store DMA Interrupt Enable */ ++// XRX200_ETHSW_IER_MACIE, /* Ethernet MAC Interrupt Enable */ ++// XRX200_ETHSW_IER_PCEIE, /* Parser and Classification Engine Interrupt Enable */ ++// XRX200_ETHSW_IER_BMIE, /* Buffer Manager Interrupt Enable */ ++// XRX200_ETHSW_ISR, /* Interrupt Status Register */ ++// XRX200_ETHSW_ISR_FDMAINT, /* Fetch DMA Interrupt */ ++// XRX200_ETHSW_ISR_SDMAINT, /* Store DMA Interrupt */ ++// XRX200_ETHSW_ISR_MACINT, /* Ethernet MAC Interrupt */ ++// XRX200_ETHSW_ISR_PCEINT, /* Parser and Classification Engine Interrupt */ ++// XRX200_ETHSW_ISR_BMINT, /* Buffer Manager Interrupt */ ++// XRX200_ETHSW_SPARE_0, /* Ethernet Switch SpareCells 0 */ ++// XRX200_ETHSW_SPARE_0_SPARE, /* SPARE0 */ ++// XRX200_ETHSW_SPARE_1, /* Ethernet Switch SpareCells 1 */ ++// XRX200_ETHSW_SPARE_1_SPARE, /* SPARE1 */ ++// XRX200_ETHSW_SPARE_2, /* Ethernet Switch SpareCells 2 */ ++// XRX200_ETHSW_SPARE_2_SPARE, /* SPARE2 */ ++// XRX200_ETHSW_SPARE_3, /* Ethernet Switch SpareCells 3 */ ++// XRX200_ETHSW_SPARE_3_SPARE, /* SPARE3 */ ++// XRX200_ETHSW_SPARE_4, /* Ethernet Switch SpareCells 4 */ ++// XRX200_ETHSW_SPARE_4_SPARE, /* SPARE4 */ ++// XRX200_ETHSW_SPARE_5, /* Ethernet Switch SpareCells 5 */ ++// XRX200_ETHSW_SPARE_5_SPARE, /* SPARE5 */ ++// XRX200_ETHSW_SPARE_6, /* Ethernet Switch SpareCells 6 */ ++// XRX200_ETHSW_SPARE_6_SPARE, /* SPARE6 */ ++// XRX200_ETHSW_SPARE_7, /* Ethernet Switch SpareCells 7 */ ++// XRX200_ETHSW_SPARE_7_SPARE, /* SPARE7 */ ++// XRX200_ETHSW_SPARE_8, /* Ethernet Switch SpareCells 8 */ ++// XRX200_ETHSW_SPARE_8_SPARE, /* SPARE8 */ ++// XRX200_ETHSW_SPARE_9, /* Ethernet Switch SpareCells 9 */ ++// XRX200_ETHSW_SPARE_9_SPARE, /* SPARE9 */ ++// XRX200_ETHSW_SPARE_10, /* Ethernet Switch SpareCells 10 */ ++// XRX200_ETHSW_SPARE_10_SPARE, /* SPARE10 */ ++// XRX200_ETHSW_SPARE_11, /* Ethernet Switch SpareCells 11 */ ++// XRX200_ETHSW_SPARE_11_SPARE, /* SPARE11 */ ++// XRX200_ETHSW_SPARE_12, /* Ethernet Switch SpareCells 12 */ ++// XRX200_ETHSW_SPARE_12_SPARE, /* SPARE12 */ ++// XRX200_ETHSW_SPARE_13, /* Ethernet Switch SpareCells 13 */ ++// XRX200_ETHSW_SPARE_13_SPARE, /* SPARE13 */ ++// XRX200_ETHSW_SPARE_14, /* Ethernet Switch SpareCells 14 */ ++// XRX200_ETHSW_SPARE_14_SPARE, /* SPARE14 */ ++// XRX200_ETHSW_SPARE_15, /* Ethernet Switch SpareCells 15 */ ++// XRX200_ETHSW_SPARE_15_SPARE, /* SPARE15 */ ++// XRX200_BM_RAM_VAL_3, /* RAM Value Register 3 */ ++// XRX200_BM_RAM_VAL_3_VAL3, /* Data value [15:0] */ ++// XRX200_BM_RAM_VAL_2, /* RAM Value Register 2 */ ++// XRX200_BM_RAM_VAL_2_VAL2, /* Data value [15:0] */ ++// XRX200_BM_RAM_VAL_1, /* RAM Value Register 1 */ ++// XRX200_BM_RAM_VAL_1_VAL1, /* Data value [15:0] */ ++// XRX200_BM_RAM_VAL_0, /* RAM Value Register 0 */ ++// XRX200_BM_RAM_VAL_0_VAL0, /* Data value [15:0] */ ++// XRX200_BM_RAM_ADDR, /* RAM Address Register */ ++// XRX200_BM_RAM_ADDR_ADDR, /* RAM Address */ ++// XRX200_BM_RAM_CTRL, /* RAM Access Control Register */ ++// XRX200_BM_RAM_CTRL_BAS, /* Access Busy/Access Start */ ++// XRX200_BM_RAM_CTRL_OPMOD, /* Lookup Table Access Operation Mode */ ++// XRX200_BM_RAM_CTRL_ADDR, /* Address for RAM selection */ ++// XRX200_BM_FSQM_GCTRL, /* Free Segment Queue ManagerGlobal Control Register */ ++// XRX200_BM_FSQM_GCTRL_SEGNUM, /* Maximum Segment Number */ ++// XRX200_BM_CONS_SEG, /* Number of Consumed SegmentsRegister */ ++// XRX200_BM_CONS_SEG_FSEG, /* Number of Consumed Segments */ ++// XRX200_BM_CONS_PKT, /* Number of Consumed PacketPointers Register */ ++// XRX200_BM_CONS_PKT_FQP, /* Number of Consumed Packet Pointers */ ++// XRX200_BM_GCTRL_F, /* Buffer Manager Global ControlRegister 0 */ ++// XRX200_BM_GCTRL_BM_STA, /* Buffer Manager Initialization Status Bit */ ++// XRX200_BM_GCTRL_SAT, /* RMON Counter Update Mode */ ++// XRX200_BM_GCTRL_FR_RBC, /* Freeze RMON RX Bad Byte 64 Bit Counter */ ++// XRX200_BM_GCTRL_FR_RGC, /* Freeze RMON RX Good Byte 64 Bit Counter */ ++// XRX200_BM_GCTRL_FR_TGC, /* Freeze RMON TX Good Byte 64 Bit Counter */ ++// XRX200_BM_GCTRL_I_FIN, /* RAM initialization finished */ ++// XRX200_BM_GCTRL_CX_INI, /* PQM Context RAM initialization */ ++// XRX200_BM_GCTRL_FP_INI, /* FPQM RAM initialization */ ++// XRX200_BM_GCTRL_FS_INI, /* FSQM RAM initialization */ ++// XRX200_BM_GCTRL_R_SRES, /* Software Reset for RMON */ ++// XRX200_BM_GCTRL_S_SRES, /* Software Reset for Scheduler */ ++// XRX200_BM_GCTRL_A_SRES, /* Software Reset for AVG */ ++// XRX200_BM_GCTRL_P_SRES, /* Software Reset for PQM */ ++// XRX200_BM_GCTRL_F_SRES, /* Software Reset for FSQM */ ++// XRX200_BM_QUEUE_GCTRL, /* Queue Manager GlobalControl Register 0 */ ++ XRX200_BM_QUEUE_GCTRL_GL_MOD, /* WRED Mode Signal */ ++// XRX200_BM_QUEUE_GCTRL_AQUI, /* Average Queue Update Interval */ ++// XRX200_BM_QUEUE_GCTRL_AQWF, /* Average Queue Weight Factor */ ++// XRX200_BM_QUEUE_GCTRL_QAVGEN, /* Queue Average Calculation Enable */ ++// XRX200_BM_QUEUE_GCTRL_DPROB, /* Drop Probability Profile */ ++// XRX200_BM_WRED_RTH_0, /* WRED Red Threshold Register0 */ ++// XRX200_BM_WRED_RTH_0_MINTH, /* Minimum Threshold */ ++// XRX200_BM_WRED_RTH_1, /* WRED Red Threshold Register1 */ ++// XRX200_BM_WRED_RTH_1_MAXTH, /* Maximum Threshold */ ++// XRX200_BM_WRED_YTH_0, /* WRED Yellow ThresholdRegister 0 */ ++// XRX200_BM_WRED_YTH_0_MINTH, /* Minimum Threshold */ ++// XRX200_BM_WRED_YTH_1, /* WRED Yellow ThresholdRegister 1 */ ++// XRX200_BM_WRED_YTH_1_MAXTH, /* Maximum Threshold */ ++// XRX200_BM_WRED_GTH_0, /* WRED Green ThresholdRegister 0 */ ++// XRX200_BM_WRED_GTH_0_MINTH, /* Minimum Threshold */ ++// XRX200_BM_WRED_GTH_1, /* WRED Green ThresholdRegister 1 */ ++// XRX200_BM_WRED_GTH_1_MAXTH, /* Maximum Threshold */ ++// XRX200_BM_DROP_GTH_0_THR, /* Drop Threshold ConfigurationRegister 0 */ ++// XRX200_BM_DROP_GTH_0_THR_FQ, /* Threshold for frames marked red */ ++// XRX200_BM_DROP_GTH_1_THY, /* Drop Threshold ConfigurationRegister 1 */ ++// XRX200_BM_DROP_GTH_1_THY_FQ, /* Threshold for frames marked yellow */ ++// XRX200_BM_DROP_GTH_2_THG, /* Drop Threshold ConfigurationRegister 2 */ ++// XRX200_BM_DROP_GTH_2_THG_FQ, /* Threshold for frames marked green */ ++// XRX200_BM_IER, /* Buffer Manager Global InterruptEnable Register */ ++// XRX200_BM_IER_CNT4, /* Counter Group 4 (RMON-CLASSIFICATION) Interrupt Enable */ ++// XRX200_BM_IER_CNT3, /* Counter Group 3 (RMON-PQM) Interrupt Enable */ ++// XRX200_BM_IER_CNT2, /* Counter Group 2 (RMON-SCHEDULER) Interrupt Enable */ ++// XRX200_BM_IER_CNT1, /* Counter Group 1 (RMON-QFETCH) Interrupt Enable */ ++// XRX200_BM_IER_CNT0, /* Counter Group 0 (RMON-QSTOR) Interrupt Enable */ ++// XRX200_BM_IER_DEQ, /* PQM dequeue Interrupt Enable */ ++// XRX200_BM_IER_ENQ, /* PQM Enqueue Interrupt Enable */ ++// XRX200_BM_IER_FSQM, /* Buffer Empty Interrupt Enable */ ++// XRX200_BM_ISR, /* Buffer Manager Global InterruptStatus Register */ ++// XRX200_BM_ISR_CNT4, /* Counter Group 4 Interrupt */ ++// XRX200_BM_ISR_CNT3, /* Counter Group 3 Interrupt */ ++// XRX200_BM_ISR_CNT2, /* Counter Group 2 Interrupt */ ++// XRX200_BM_ISR_CNT1, /* Counter Group 1 Interrupt */ ++// XRX200_BM_ISR_CNT0, /* Counter Group 0 Interrupt */ ++// XRX200_BM_ISR_DEQ, /* PQM dequeue Interrupt Enable */ ++// XRX200_BM_ISR_ENQ, /* PQM Enqueue Interrupt */ ++// XRX200_BM_ISR_FSQM, /* Buffer Empty Interrupt */ ++// XRX200_BM_CISEL, /* Buffer Manager RMON CounterInterrupt Select Register */ ++// XRX200_BM_CISEL_PORT, /* Port Number */ ++// XRX200_BM_DEBUG_CTRL_DBG, /* Debug Control Register */ ++// XRX200_BM_DEBUG_CTRL_DBG_SEL, /* Select Signal for Debug Multiplexer */ ++// XRX200_BM_DEBUG_VAL_DBG, /* Debug Value Register */ ++// XRX200_BM_DEBUG_VAL_DBG_DAT, /* Debug Data Value */ ++// XRX200_BM_PCFG, /* Buffer Manager PortConfiguration Register */ ++// XRX200_BM_PCFG_CNTEN, /* RMON Counter Enable */ ++// XRX200_BM_RMON_CTRL_RAM1, /* Buffer ManagerRMON Control Register */ ++// XRX200_BM_RMON_CTRL_RAM2_RES, /* Software Reset for RMON RAM2 */ ++// XRX200_BM_RMON_CTRL_RAM1_RES, /* Software Reset for RMON RAM1 */ ++// XRX200_PQM_DP, /* Packet Queue ManagerDrop Probability Register */ ++// XRX200_PQM_DP_DPROB, /* Drop Probability Profile */ ++// XRX200_PQM_RS, /* Packet Queue ManagerRate Shaper Assignment Register */ ++// XRX200_PQM_RS_EN2, /* Rate Shaper 2 Enable */ ++// XRX200_PQM_RS_RS2, /* Rate Shaper 2 */ ++// XRX200_PQM_RS_EN1, /* Rate Shaper 1 Enable */ ++// XRX200_PQM_RS_RS1, /* Rate Shaper 1 */ ++// XRX200_RS_CTRL, /* Rate Shaper ControlRegister */ ++// XRX200_RS_CTRL_RSEN, /* Rate Shaper Enable */ ++// XRX200_RS_CBS, /* Rate Shaper CommittedBurst Size Register */ ++// XRX200_RS_CBS_CBS, /* Committed Burst Size */ ++// XRX200_RS_IBS, /* Rate Shaper InstantaneousBurst Size Register */ ++// XRX200_RS_IBS_IBS, /* Instantaneous Burst Size */ ++// XRX200_RS_CIR_EXP, /* Rate Shaper RateExponent Register */ ++// XRX200_RS_CIR_EXP_EXP, /* Exponent */ ++// XRX200_RS_CIR_MANT, /* Rate Shaper RateMantissa Register */ ++// XRX200_RS_CIR_MANT_MANT, /* Mantissa */ ++ XRX200_PCE_TBL_KEY_7, /* Table Key Data 7 */ ++// XRX200_PCE_TBL_KEY_7_KEY7, /* Key Value[15:0] */ ++ XRX200_PCE_TBL_KEY_6, /* Table Key Data 6 */ ++// XRX200_PCE_TBL_KEY_6_KEY6, /* Key Value[15:0] */ ++ XRX200_PCE_TBL_KEY_5, /* Table Key Data 5 */ ++// XRX200_PCE_TBL_KEY_5_KEY5, /* Key Value[15:0] */ ++ XRX200_PCE_TBL_KEY_4, /* Table Key Data 4 */ ++// XRX200_PCE_TBL_KEY_4_KEY4, /* Key Value[15:0] */ ++ XRX200_PCE_TBL_KEY_3, /* Table Key Data 3 */ ++// XRX200_PCE_TBL_KEY_3_KEY3, /* Key Value[15:0] */ ++ XRX200_PCE_TBL_KEY_2, /* Table Key Data 2 */ ++// XRX200_PCE_TBL_KEY_2_KEY2, /* Key Value[15:0] */ ++ XRX200_PCE_TBL_KEY_1, /* Table Key Data 1 */ ++// XRX200_PCE_TBL_KEY_1_KEY1, /* Key Value[31:16] */ ++ XRX200_PCE_TBL_KEY_0, /* Table Key Data 0 */ ++// XRX200_PCE_TBL_KEY_0_KEY0, /* Key Value[15:0] */ ++ XRX200_PCE_TBL_MASK_0, /* Table Mask Write Register0 */ ++// XRX200_PCE_TBL_MASK_0_MASK0, /* Mask Pattern [15:0] */ ++ XRX200_PCE_TBL_VAL_4, /* Table Value Register4 */ ++// XRX200_PCE_TBL_VAL_4_VAL4, /* Data value [15:0] */ ++ XRX200_PCE_TBL_VAL_3, /* Table Value Register3 */ ++// XRX200_PCE_TBL_VAL_3_VAL3, /* Data value [15:0] */ ++ XRX200_PCE_TBL_VAL_2, /* Table Value Register2 */ ++// XRX200_PCE_TBL_VAL_2_VAL2, /* Data value [15:0] */ ++ XRX200_PCE_TBL_VAL_1, /* Table Value Register1 */ ++// XRX200_PCE_TBL_VAL_1_VAL1, /* Data value [15:0] */ ++ XRX200_PCE_TBL_VAL_0, /* Table Value Register0 */ ++// XRX200_PCE_TBL_VAL_0_VAL0, /* Data value [15:0] */ ++// XRX200_PCE_TBL_ADDR, /* Table Entry AddressRegister */ ++ XRX200_PCE_TBL_ADDR_ADDR, /* Table Address */ ++// XRX200_PCE_TBL_CTRL, /* Table Access ControlRegister */ ++ XRX200_PCE_TBL_CTRL_BAS, /* Access Busy/Access Start */ ++ XRX200_PCE_TBL_CTRL_TYPE, /* Lookup Entry Type */ ++ XRX200_PCE_TBL_CTRL_VLD, /* Lookup Entry Valid */ ++ XRX200_PCE_TBL_CTRL_GMAP, /* Group Map */ ++ XRX200_PCE_TBL_CTRL_OPMOD, /* Lookup Table Access Operation Mode */ ++ XRX200_PCE_TBL_CTRL_ADDR, /* Lookup Table Address */ ++// XRX200_PCE_TBL_STAT, /* Table General StatusRegister */ ++// XRX200_PCE_TBL_STAT_TBUSY, /* Table Access Busy */ ++// XRX200_PCE_TBL_STAT_TEMPT, /* Table Empty */ ++// XRX200_PCE_TBL_STAT_TFUL, /* Table Full */ ++// XRX200_PCE_AGE_0, /* Aging Counter ConfigurationRegister 0 */ ++// XRX200_PCE_AGE_0_EXP, /* Aging Counter Exponent Value */ ++// XRX200_PCE_AGE_1, /* Aging Counter ConfigurationRegister 1 */ ++// XRX200_PCE_AGE_1_MANT, /* Aging Counter Mantissa Value */ ++// XRX200_PCE_PMAP_1, /* Port Map Register 1 */ ++// XRX200_PCE_PMAP_1_MPMAP, /* Monitoring Port Map */ ++// XRX200_PCE_PMAP_2, /* Port Map Register 2 */ ++// XRX200_PCE_PMAP_2_DMCPMAP, /* Default Multicast Port Map */ ++// XRX200_PCE_PMAP_3, /* Port Map Register 3 */ ++// XRX200_PCE_PMAP_3_UUCMAP, /* Default Unknown Unicast Port Map */ ++// XRX200_PCE_GCTRL_0, /* PCE Global Control Register0 */ ++// XRX200_PCE_GCTRL_0_IGMP, /* IGMP Mode Selection */ ++ XRX200_PCE_GCTRL_0_VLAN, /* VLAN-aware Switching */ ++// XRX200_PCE_GCTRL_0_NOPM, /* No Port Map Forwarding */ ++// XRX200_PCE_GCTRL_0_SCONUC, /* Unknown Unicast Storm Control */ ++// XRX200_PCE_GCTRL_0_SCONMC, /* Multicast Storm Control */ ++// XRX200_PCE_GCTRL_0_SCONBC, /* Broadcast Storm Control */ ++// XRX200_PCE_GCTRL_0_SCONMOD, /* Storm Control Mode */ ++// XRX200_PCE_GCTRL_0_SCONMET, /* Storm Control Metering Instance */ ++// XRX200_PCE_GCTRL_0_MC_VALID, /* Access Request */ ++// XRX200_PCE_GCTRL_0_PLCKMOD, /* Port Lock Mode */ ++// XRX200_PCE_GCTRL_0_PLIMMOD, /* MAC Address Learning Limitation Mode */ ++// XRX200_PCE_GCTRL_0_MTFL, /* MAC Table Flushing */ ++// XRX200_PCE_GCTRL_1, /* PCE Global Control Register1 */ ++// XRX200_PCE_GCTRL_1_PCE_DIS, /* PCE Disable after currently processed packet */ ++// XRX200_PCE_GCTRL_1_LRNMOD, /* MAC Address Learning Mode */ ++// XRX200_PCE_TCM_GLOB_CTRL, /* Three-color MarkerGlobal Control Register */ ++// XRX200_PCE_TCM_GLOB_CTRL_DPRED, /* Re-marking Drop Precedence Red Encoding */ ++// XRX200_PCE_TCM_GLOB_CTRL_DPYEL, /* Re-marking Drop Precedence Yellow Encoding */ ++// XRX200_PCE_TCM_GLOB_CTRL_DPGRN, /* Re-marking Drop Precedence Green Encoding */ ++// XRX200_PCE_IGMP_CTRL, /* IGMP Control Register */ ++// XRX200_PCE_IGMP_CTRL_FAGEEN, /* Force Aging of Table Entries Enable */ ++// XRX200_PCE_IGMP_CTRL_FLEAVE, /* Fast Leave Enable */ ++// XRX200_PCE_IGMP_CTRL_DMRTEN, /* Default Maximum Response Time Enable */ ++// XRX200_PCE_IGMP_CTRL_JASUP, /* Join Aggregation Suppression Enable */ ++// XRX200_PCE_IGMP_CTRL_REPSUP, /* Report Suppression Enable */ ++// XRX200_PCE_IGMP_CTRL_SRPEN, /* Snooping of Router Port Enable */ ++// XRX200_PCE_IGMP_CTRL_ROB, /* Robustness Variable */ ++// XRX200_PCE_IGMP_CTRL_DMRT, /* IGMP Default Maximum Response Time */ ++// XRX200_PCE_IGMP_DRPM, /* IGMP Default RouterPort Map Register */ ++// XRX200_PCE_IGMP_DRPM_DRPM, /* IGMP Default Router Port Map */ ++// XRX200_PCE_IGMP_AGE_0, /* IGMP Aging Register0 */ ++// XRX200_PCE_IGMP_AGE_0_MANT, /* IGMP Group Aging Time Mantissa */ ++// XRX200_PCE_IGMP_AGE_0_EXP, /* IGMP Group Aging Time Exponent */ ++// XRX200_PCE_IGMP_AGE_1, /* IGMP Aging Register1 */ ++// XRX200_PCE_IGMP_AGE_1_MANT, /* IGMP Router Port Aging Time Mantissa */ ++// XRX200_PCE_IGMP_STAT, /* IGMP Status Register */ ++// XRX200_PCE_IGMP_STAT_IGPM, /* IGMP Port Map */ ++// XRX200_WOL_GLB_CTRL, /* Wake-on-LAN ControlRegister */ ++// XRX200_WOL_GLB_CTRL_PASSEN, /* WoL Password Enable */ ++// XRX200_WOL_DA_0, /* Wake-on-LAN DestinationAddress Register 0 */ ++// XRX200_WOL_DA_0_DA0, /* WoL Destination Address [15:0] */ ++// XRX200_WOL_DA_1, /* Wake-on-LAN DestinationAddress Register 1 */ ++// XRX200_WOL_DA_1_DA1, /* WoL Destination Address [31:16] */ ++// XRX200_WOL_DA_2, /* Wake-on-LAN DestinationAddress Register 2 */ ++// XRX200_WOL_DA_2_DA2, /* WoL Destination Address [47:32] */ ++// XRX200_WOL_PW_0, /* Wake-on-LAN Password Register0 */ ++// XRX200_WOL_PW_0_PW0, /* WoL Password [15:0] */ ++// XRX200_WOL_PW_1, /* Wake-on-LAN Password Register1 */ ++// XRX200_WOL_PW_1_PW1, /* WoL Password [31:16] */ ++// XRX200_WOL_PW_2, /* Wake-on-LAN Password Register2 */ ++// XRX200_WOL_PW_2_PW2, /* WoL Password [47:32] */ ++// XRX200_PCE_IER_0_PINT, /* Parser and ClassificationEngine Global Interrupt Enable Register 0 */ ++// XRX200_PCE_IER_0_PINT_15, /* Port Interrupt Enable */ ++// XRX200_PCE_IER_0_PINT_14, /* Port Interrupt Enable */ ++// XRX200_PCE_IER_0_PINT_13, /* Port Interrupt Enable */ ++// XRX200_PCE_IER_0_PINT_12, /* Port Interrupt Enable */ ++// XRX200_PCE_IER_0_PINT_11, /* Port Interrupt Enable */ ++// XRX200_PCE_IER_0_PINT_10, /* Port Interrupt Enable */ ++// XRX200_PCE_IER_0_PINT_9, /* Port Interrupt Enable */ ++// XRX200_PCE_IER_0_PINT_8, /* Port Interrupt Enable */ ++// XRX200_PCE_IER_0_PINT_7, /* Port Interrupt Enable */ ++// XRX200_PCE_IER_0_PINT_6, /* Port Interrupt Enable */ ++// XRX200_PCE_IER_0_PINT_5, /* Port Interrupt Enable */ ++// XRX200_PCE_IER_0_PINT_4, /* Port Interrupt Enable */ ++// XRX200_PCE_IER_0_PINT_3, /* Port Interrupt Enable */ ++// XRX200_PCE_IER_0_PINT_2, /* Port Interrupt Enable */ ++// XRX200_PCE_IER_0_PINT_1, /* Port Interrupt Enable */ ++// XRX200_PCE_IER_0_PINT_0, /* Port Interrupt Enable */ ++// XRX200_PCE_IER_1, /* Parser and ClassificationEngine Global Interrupt Enable Register 1 */ ++// XRX200_PCE_IER_1_FLOWINT, /* Traffic Flow Table Interrupt Rule matched Interrupt Enable */ ++// XRX200_PCE_IER_1_CPH2, /* Classification Phase 2 Ready Interrupt Enable */ ++// XRX200_PCE_IER_1_CPH1, /* Classification Phase 1 Ready Interrupt Enable */ ++// XRX200_PCE_IER_1_CPH0, /* Classification Phase 0 Ready Interrupt Enable */ ++// XRX200_PCE_IER_1_PRDY, /* Parser Ready Interrupt Enable */ ++// XRX200_PCE_IER_1_IGTF, /* IGMP Table Full Interrupt Enable */ ++// XRX200_PCE_IER_1_MTF, /* MAC Table Full Interrupt Enable */ ++// XRX200_PCE_ISR_0_PINT, /* Parser and ClassificationEngine Global Interrupt Status Register 0 */ ++// XRX200_PCE_ISR_0_PINT_15, /* Port Interrupt */ ++// XRX200_PCE_ISR_0_PINT_14, /* Port Interrupt */ ++// XRX200_PCE_ISR_0_PINT_13, /* Port Interrupt */ ++// XRX200_PCE_ISR_0_PINT_12, /* Port Interrupt */ ++// XRX200_PCE_ISR_0_PINT_11, /* Port Interrupt */ ++// XRX200_PCE_ISR_0_PINT_10, /* Port Interrupt */ ++// XRX200_PCE_ISR_0_PINT_9, /* Port Interrupt */ ++// XRX200_PCE_ISR_0_PINT_8, /* Port Interrupt */ ++// XRX200_PCE_ISR_0_PINT_7, /* Port Interrupt */ ++// XRX200_PCE_ISR_0_PINT_6, /* Port Interrupt */ ++// XRX200_PCE_ISR_0_PINT_5, /* Port Interrupt */ ++// XRX200_PCE_ISR_0_PINT_4, /* Port Interrupt */ ++// XRX200_PCE_ISR_0_PINT_3, /* Port Interrupt */ ++// XRX200_PCE_ISR_0_PINT_2, /* Port Interrupt */ ++// XRX200_PCE_ISR_0_PINT_1, /* Port Interrupt */ ++// XRX200_PCE_ISR_0_PINT_0, /* Port Interrupt */ ++// XRX200_PCE_ISR_1, /* Parser and ClassificationEngine Global Interrupt Status Register 1 */ ++// XRX200_PCE_ISR_1_FLOWINT, /* Traffic Flow Table Interrupt Rule matched */ ++// XRX200_PCE_ISR_1_CPH2, /* Classification Phase 2 Ready Interrupt */ ++// XRX200_PCE_ISR_1_CPH1, /* Classification Phase 1 Ready Interrupt */ ++// XRX200_PCE_ISR_1_CPH0, /* Classification Phase 0 Ready Interrupt */ ++// XRX200_PCE_ISR_1_PRDY, /* Parser Ready Interrupt */ ++// XRX200_PCE_ISR_1_IGTF, /* IGMP Table Full Interrupt */ ++// XRX200_PCE_ISR_1_MTF, /* MAC Table Full Interrupt */ ++// XRX200_PARSER_STAT_FIFO, /* Parser Status Register */ ++// XRX200_PARSER_STAT_FSM_DAT_CNT, /* Parser FSM Data Counter */ ++// XRX200_PARSER_STAT_FSM_STATE, /* Parser FSM State */ ++// XRX200_PARSER_STAT_PKT_ERR, /* Packet error detected */ ++// XRX200_PARSER_STAT_FSM_FIN, /* Parser FSM finished */ ++// XRX200_PARSER_STAT_FSM_START, /* Parser FSM start */ ++// XRX200_PARSER_STAT_FIFO_RDY, /* Parser FIFO ready for read. */ ++// XRX200_PARSER_STAT_FIFO_FULL, /* Parser */ ++// XRX200_PCE_PCTRL_0, /* PCE Port ControlRegister 0 */ ++// XRX200_PCE_PCTRL_0_MCST, /* Multicast Forwarding Mode Selection */ ++// XRX200_PCE_PCTRL_0_EGSTEN, /* Table-based Egress Special Tag Enable */ ++// XRX200_PCE_PCTRL_0_IGSTEN, /* Ingress Special Tag Enable */ ++// XRX200_PCE_PCTRL_0_PCPEN, /* PCP Remarking Mode */ ++// XRX200_PCE_PCTRL_0_CLPEN, /* Class Remarking Mode */ ++// XRX200_PCE_PCTRL_0_DPEN, /* Drop Precedence Remarking Mode */ ++// XRX200_PCE_PCTRL_0_CMOD, /* Three-color Marker Color Mode */ ++// XRX200_PCE_PCTRL_0_VREP, /* VLAN Replacement Mode */ ++ XRX200_PCE_PCTRL_0_TVM, /* Transparent VLAN Mode */ ++// XRX200_PCE_PCTRL_0_PLOCK, /* Port Locking Enable */ ++// XRX200_PCE_PCTRL_0_AGEDIS, /* Aging Disable */ ++// XRX200_PCE_PCTRL_0_PSTATE, /* Port State */ ++// XRX200_PCE_PCTRL_1, /* PCE Port ControlRegister 1 */ ++// XRX200_PCE_PCTRL_1_LRNLIM, /* MAC Address Learning Limit */ ++// XRX200_PCE_PCTRL_2, /* PCE Port ControlRegister 2 */ ++// XRX200_PCE_PCTRL_2_DSCPMOD, /* DSCP Mode Selection */ ++// XRX200_PCE_PCTRL_2_DSCP, /* Enable DSCP to select the Class of Service */ ++// XRX200_PCE_PCTRL_2_PCP, /* Enable VLAN PCP to select the Class of Service */ ++// XRX200_PCE_PCTRL_2_PCLASS, /* Port-based Traffic Class */ ++// XRX200_PCE_PCTRL_3_VIO, /* PCE Port ControlRegister 3 */ ++// XRX200_PCE_PCTRL_3_EDIR, /* Egress Redirection Mode */ ++// XRX200_PCE_PCTRL_3_RXDMIR, /* Receive Mirroring Enable for dropped frames */ ++// XRX200_PCE_PCTRL_3_RXVMIR, /* Receive Mirroring Enable for valid frames */ ++// XRX200_PCE_PCTRL_3_TXMIR, /* Transmit Mirroring Enable */ ++// XRX200_PCE_PCTRL_3_VIO_7, /* Violation Type 7 Mirroring Enable */ ++// XRX200_PCE_PCTRL_3_VIO_6, /* Violation Type 6 Mirroring Enable */ ++// XRX200_PCE_PCTRL_3_VIO_5, /* Violation Type 5 Mirroring Enable */ ++// XRX200_PCE_PCTRL_3_VIO_4, /* Violation Type 4 Mirroring Enable */ ++// XRX200_PCE_PCTRL_3_VIO_3, /* Violation Type 3 Mirroring Enable */ ++// XRX200_PCE_PCTRL_3_VIO_2, /* Violation Type 2 Mirroring Enable */ ++// XRX200_PCE_PCTRL_3_VIO_1, /* Violation Type 1 Mirroring Enable */ ++// XRX200_PCE_PCTRL_3_VIO_0, /* Violation Type 0 Mirroring Enable */ ++// XRX200_WOL_CTRL, /* Wake-on-LAN ControlRegister */ ++// XRX200_WOL_CTRL_PORT, /* WoL Enable */ ++// XRX200_PCE_VCTRL, /* PCE VLAN ControlRegister */ ++ XRX200_PCE_VCTRL_VSR, /* VLAN Security Rule */ ++ XRX200_PCE_VCTRL_VEMR, /* VLAN Egress Member Violation Rule */ ++ XRX200_PCE_VCTRL_VIMR, /* VLAN Ingress Member Violation Rule */ ++ XRX200_PCE_VCTRL_VINR, /* VLAN Ingress Tag Rule */ ++ XRX200_PCE_VCTRL_UVR, /* Unknown VLAN Rule */ ++// XRX200_PCE_DEFPVID, /* PCE Default PortVID Register */ ++ XRX200_PCE_DEFPVID_PVID, /* Default Port VID Index */ ++// XRX200_PCE_PSTAT, /* PCE Port StatusRegister */ ++// XRX200_PCE_PSTAT_LRNCNT, /* Learning Count */ ++// XRX200_PCE_PIER, /* Parser and ClassificationEngine Port Interrupt Enable Register */ ++// XRX200_PCE_PIER_CLDRP, /* Classification Drop Interrupt Enable */ ++// XRX200_PCE_PIER_PTDRP, /* Port Drop Interrupt Enable */ ++// XRX200_PCE_PIER_VLAN, /* VLAN Violation Interrupt Enable */ ++// XRX200_PCE_PIER_WOL, /* Wake-on-LAN Interrupt Enable */ ++// XRX200_PCE_PIER_LOCK, /* Port Limit Alert Interrupt Enable */ ++// XRX200_PCE_PIER_LIM, /* Port Lock Alert Interrupt Enable */ ++// XRX200_PCE_PISR, /* Parser and ClassificationEngine Port Interrupt Status Register */ ++// XRX200_PCE_PISR_CLDRP, /* Classification Drop Interrupt */ ++// XRX200_PCE_PISR_PTDRP, /* Port Drop Interrupt */ ++// XRX200_PCE_PISR_VLAN, /* VLAN Violation Interrupt */ ++// XRX200_PCE_PISR_WOL, /* Wake-on-LAN Interrupt */ ++// XRX200_PCE_PISR_LOCK, /* Port Lock Alert Interrupt */ ++// XRX200_PCE_PISR_LIMIT, /* Port Limitation Alert Interrupt */ ++// XRX200_PCE_TCM_CTRL, /* Three-colorMarker Control Register */ ++// XRX200_PCE_TCM_CTRL_TCMEN, /* Three-color Marker metering instance enable */ ++// XRX200_PCE_TCM_STAT, /* Three-colorMarker Status Register */ ++// XRX200_PCE_TCM_STAT_AL1, /* Three-color Marker Alert 1 Status */ ++// XRX200_PCE_TCM_STAT_AL0, /* Three-color Marker Alert 0 Status */ ++// XRX200_PCE_TCM_CBS, /* Three-color MarkerCommitted Burst Size Register */ ++// XRX200_PCE_TCM_CBS_CBS, /* Committed Burst Size */ ++// XRX200_PCE_TCM_EBS, /* Three-color MarkerExcess Burst Size Register */ ++// XRX200_PCE_TCM_EBS_EBS, /* Excess Burst Size */ ++// XRX200_PCE_TCM_IBS, /* Three-color MarkerInstantaneous Burst Size Register */ ++// XRX200_PCE_TCM_IBS_IBS, /* Instantaneous Burst Size */ ++// XRX200_PCE_TCM_CIR_MANT, /* Three-colorMarker Constant Information Rate Mantissa Register */ ++// XRX200_PCE_TCM_CIR_MANT_MANT, /* Rate Counter Mantissa */ ++// XRX200_PCE_TCM_CIR_EXP, /* Three-colorMarker Constant Information Rate Exponent Register */ ++// XRX200_PCE_TCM_CIR_EXP_EXP, /* Rate Counter Exponent */ ++// XRX200_MAC_TEST, /* MAC Test Register */ ++// XRX200_MAC_TEST_JTP, /* Jitter Test Pattern */ ++// XRX200_MAC_PFAD_CFG, /* MAC Pause FrameSource Address Configuration Register */ ++// XRX200_MAC_PFAD_CFG_SAMOD, /* Source Address Mode */ ++// XRX200_MAC_PFSA_0, /* Pause Frame SourceAddress Part 0 */ ++// XRX200_MAC_PFSA_0_PFAD, /* Pause Frame Source Address Part 0 */ ++// XRX200_MAC_PFSA_1, /* Pause Frame SourceAddress Part 1 */ ++// XRX200_MAC_PFSA_1_PFAD, /* Pause Frame Source Address Part 1 */ ++// XRX200_MAC_PFSA_2, /* Pause Frame SourceAddress Part 2 */ ++// XRX200_MAC_PFSA_2_PFAD, /* Pause Frame Source Address Part 2 */ ++// XRX200_MAC_FLEN, /* MAC Frame Length Register */ ++// XRX200_MAC_FLEN_LEN, /* Maximum Frame Length */ ++// XRX200_MAC_VLAN_ETYPE_0, /* MAC VLAN EthertypeRegister 0 */ ++// XRX200_MAC_VLAN_ETYPE_0_OUTER, /* Ethertype */ ++// XRX200_MAC_VLAN_ETYPE_1, /* MAC VLAN EthertypeRegister 1 */ ++// XRX200_MAC_VLAN_ETYPE_1_INNER, /* Ethertype */ ++// XRX200_MAC_IER, /* MAC Interrupt EnableRegister */ ++// XRX200_MAC_IER_MACIEN, /* MAC Interrupt Enable */ ++// XRX200_MAC_ISR, /* MAC Interrupt StatusRegister */ ++// XRX200_MAC_ISR_MACINT, /* MAC Interrupt */ ++// XRX200_MAC_PSTAT, /* MAC Port Status Register */ ++// XRX200_MAC_PSTAT_PACT, /* PHY Active Status */ ++ XRX200_MAC_PSTAT_GBIT, /* Gigabit Speed Status */ ++ XRX200_MAC_PSTAT_MBIT, /* Megabit Speed Status */ ++ XRX200_MAC_PSTAT_FDUP, /* Full Duplex Status */ ++// XRX200_MAC_PSTAT_RXPAU, /* Receive Pause Status */ ++// XRX200_MAC_PSTAT_TXPAU, /* Transmit Pause Status */ ++// XRX200_MAC_PSTAT_RXPAUEN, /* Receive Pause Enable Status */ ++// XRX200_MAC_PSTAT_TXPAUEN, /* Transmit Pause Enable Status */ ++ XRX200_MAC_PSTAT_LSTAT, /* Link Status */ ++// XRX200_MAC_PSTAT_CRS, /* Carrier Sense Status */ ++// XRX200_MAC_PSTAT_TXLPI, /* Transmit Low-power Idle Status */ ++// XRX200_MAC_PSTAT_RXLPI, /* Receive Low-power Idle Status */ ++// XRX200_MAC_PISR, /* MAC Interrupt Status Register */ ++// XRX200_MAC_PISR_PACT, /* PHY Active Status */ ++// XRX200_MAC_PISR_SPEED, /* Megabit Speed Status */ ++// XRX200_MAC_PISR_FDUP, /* Full Duplex Status */ ++// XRX200_MAC_PISR_RXPAUEN, /* Receive Pause Enable Status */ ++// XRX200_MAC_PISR_TXPAUEN, /* Transmit Pause Enable Status */ ++// XRX200_MAC_PISR_LPIOFF, /* Receive Low-power Idle Mode is left */ ++// XRX200_MAC_PISR_LPION, /* Receive Low-power Idle Mode is entered */ ++// XRX200_MAC_PISR_JAM, /* Jam Status Detected */ ++// XRX200_MAC_PISR_TOOSHORT, /* Too Short Frame Error Detected */ ++// XRX200_MAC_PISR_TOOLONG, /* Too Long Frame Error Detected */ ++// XRX200_MAC_PISR_LENERR, /* Length Mismatch Error Detected */ ++// XRX200_MAC_PISR_FCSERR, /* Frame Checksum Error Detected */ ++// XRX200_MAC_PISR_TXPAUSE, /* Pause Frame Transmitted */ ++// XRX200_MAC_PISR_RXPAUSE, /* Pause Frame Received */ ++// XRX200_MAC_PIER, /* MAC Interrupt Enable Register */ ++// XRX200_MAC_PIER_PACT, /* PHY Active Status */ ++// XRX200_MAC_PIER_SPEED, /* Megabit Speed Status */ ++// XRX200_MAC_PIER_FDUP, /* Full Duplex Status */ ++// XRX200_MAC_PIER_RXPAUEN, /* Receive Pause Enable Status */ ++// XRX200_MAC_PIER_TXPAUEN, /* Transmit Pause Enable Status */ ++// XRX200_MAC_PIER_LPIOFF, /* Low-power Idle Off Interrupt Mask */ ++// XRX200_MAC_PIER_LPION, /* Low-power Idle On Interrupt Mask */ ++// XRX200_MAC_PIER_JAM, /* Jam Status Interrupt Mask */ ++// XRX200_MAC_PIER_TOOSHORT, /* Too Short Frame Error Interrupt Mask */ ++// XRX200_MAC_PIER_TOOLONG, /* Too Long Frame Error Interrupt Mask */ ++// XRX200_MAC_PIER_LENERR, /* Length Mismatch Error Interrupt Mask */ ++// XRX200_MAC_PIER_FCSERR, /* Frame Checksum Error Interrupt Mask */ ++// XRX200_MAC_PIER_TXPAUSE, /* Transmit Pause Frame Interrupt Mask */ ++// XRX200_MAC_PIER_RXPAUSE, /* Receive Pause Frame Interrupt Mask */ ++// XRX200_MAC_CTRL_0, /* MAC Control Register0 */ ++// XRX200_MAC_CTRL_0_LCOL, /* Late Collision Control */ ++// XRX200_MAC_CTRL_0_BM, /* Burst Mode Control */ ++// XRX200_MAC_CTRL_0_APADEN, /* Automatic VLAN Padding Enable */ ++// XRX200_MAC_CTRL_0_VPAD2EN, /* Stacked VLAN Padding Enable */ ++// XRX200_MAC_CTRL_0_VPADEN, /* VLAN Padding Enable */ ++// XRX200_MAC_CTRL_0_PADEN, /* Padding Enable */ ++// XRX200_MAC_CTRL_0_FCS, /* Transmit FCS Control */ ++ XRX200_MAC_CTRL_0_FCON, /* Flow Control Mode */ ++// XRX200_MAC_CTRL_0_FDUP, /* Full Duplex Control */ ++// XRX200_MAC_CTRL_0_GMII, /* GMII/MII interface mode selection */ ++// XRX200_MAC_CTRL_1, /* MAC Control Register1 */ ++// XRX200_MAC_CTRL_1_SHORTPRE, /* Short Preamble Control */ ++// XRX200_MAC_CTRL_1_IPG, /* Minimum Inter Packet Gap Size */ ++// XRX200_MAC_CTRL_2, /* MAC Control Register2 */ ++// XRX200_MAC_CTRL_2_MLEN, /* Maximum Untagged Frame Length */ ++// XRX200_MAC_CTRL_2_LCHKL, /* Frame Length Check Long Enable */ ++// XRX200_MAC_CTRL_2_LCHKS, /* Frame Length Check Short Enable */ ++// XRX200_MAC_CTRL_3, /* MAC Control Register3 */ ++// XRX200_MAC_CTRL_3_RCNT, /* Retry Count */ ++// XRX200_MAC_CTRL_4, /* MAC Control Register4 */ ++// XRX200_MAC_CTRL_4_LPIEN, /* LPI Mode Enable */ ++// XRX200_MAC_CTRL_4_WAIT, /* LPI Wait Time */ ++// XRX200_MAC_CTRL_5_PJPS, /* MAC Control Register5 */ ++// XRX200_MAC_CTRL_5_PJPS_NOBP, /* Prolonged Jam pattern size during no-backpressure state */ ++// XRX200_MAC_CTRL_5_PJPS_BP, /* Prolonged Jam pattern size during backpressure state */ ++// XRX200_MAC_CTRL_6_XBUF, /* Transmit and ReceiveBuffer Control Register */ ++// XRX200_MAC_CTRL_6_RBUF_DLY_WP, /* Delay */ ++// XRX200_MAC_CTRL_6_RBUF_INIT, /* Receive Buffer Initialization */ ++// XRX200_MAC_CTRL_6_RBUF_BYPASS, /* Bypass the Receive Buffer */ ++// XRX200_MAC_CTRL_6_XBUF_DLY_WP, /* Delay */ ++// XRX200_MAC_CTRL_6_XBUF_INIT, /* Initialize the Transmit Buffer */ ++// XRX200_MAC_CTRL_6_XBUF_BYPASS, /* Bypass the Transmit Buffer */ ++// XRX200_MAC_BUFST_XBUF, /* MAC Receive and TransmitBuffer Status Register */ ++// XRX200_MAC_BUFST_RBUF_UFL, /* Receive Buffer Underflow Indicator */ ++// XRX200_MAC_BUFST_RBUF_OFL, /* Receive Buffer Overflow Indicator */ ++// XRX200_MAC_BUFST_XBUF_UFL, /* Transmit Buffer Underflow Indicator */ ++// XRX200_MAC_BUFST_XBUF_OFL, /* Transmit Buffer Overflow Indicator */ ++// XRX200_MAC_TESTEN, /* MAC Test Enable Register */ ++// XRX200_MAC_TESTEN_JTEN, /* Jitter Test Enable */ ++// XRX200_MAC_TESTEN_TXER, /* Transmit Error Insertion */ ++// XRX200_MAC_TESTEN_LOOP, /* MAC Loopback Enable */ ++// XRX200_FDMA_CTRL, /* Ethernet Switch FetchDMA Control Register */ ++// XRX200_FDMA_CTRL_LPI_THRESHOLD, /* Low Power Idle Threshold */ ++// XRX200_FDMA_CTRL_LPI_MODE, /* Low Power Idle Mode */ ++// XRX200_FDMA_CTRL_EGSTAG, /* Egress Special Tag Size */ ++// XRX200_FDMA_CTRL_IGSTAG, /* Ingress Special Tag Size */ ++// XRX200_FDMA_CTRL_EXCOL, /* Excessive Collision Handling */ ++// XRX200_FDMA_STETYPE, /* Special Tag EthertypeControl Register */ ++// XRX200_FDMA_STETYPE_ETYPE, /* Special Tag Ethertype */ ++// XRX200_FDMA_VTETYPE, /* VLAN Tag EthertypeControl Register */ ++// XRX200_FDMA_VTETYPE_ETYPE, /* VLAN Tag Ethertype */ ++// XRX200_FDMA_STAT_0, /* FDMA Status Register0 */ ++// XRX200_FDMA_STAT_0_FSMS, /* FSM states status */ ++// XRX200_FDMA_IER, /* Fetch DMA Global InterruptEnable Register */ ++// XRX200_FDMA_IER_PCKD, /* Packet Drop Interrupt Enable */ ++// XRX200_FDMA_IER_PCKR, /* Packet Ready Interrupt Enable */ ++// XRX200_FDMA_IER_PCKT, /* Packet Sent Interrupt Enable */ ++// XRX200_FDMA_ISR, /* Fetch DMA Global InterruptStatus Register */ ++// XRX200_FDMA_ISR_PCKTD, /* Packet Drop */ ++// XRX200_FDMA_ISR_PCKR, /* Packet is Ready for Transmission */ ++// XRX200_FDMA_ISR_PCKT, /* Packet Sent Event */ ++// XRX200_FDMA_PCTRL, /* Ethernet SwitchFetch DMA Port Control Register */ ++// XRX200_FDMA_PCTRL_VLANMOD, /* VLAN Modification Enable */ ++// XRX200_FDMA_PCTRL_DSCPRM, /* DSCP Re-marking Enable */ ++// XRX200_FDMA_PCTRL_STEN, /* Special Tag Insertion Enable */ ++// XRX200_FDMA_PCTRL_EN, /* FDMA Port Enable */ ++// XRX200_FDMA_PRIO, /* Ethernet SwitchFetch DMA Port Priority Register */ ++// XRX200_FDMA_PRIO_PRIO, /* FDMA PRIO */ ++// XRX200_FDMA_PSTAT0, /* Ethernet SwitchFetch DMA Port Status Register 0 */ ++// XRX200_FDMA_PSTAT0_PKT_AVAIL, /* Port Egress Packet Available */ ++// XRX200_FDMA_PSTAT0_POK, /* Port Status OK */ ++// XRX200_FDMA_PSTAT0_PSEG, /* Port Egress Segment Count */ ++// XRX200_FDMA_PSTAT1_HDR, /* Ethernet SwitchFetch DMA Port Status Register 1 */ ++// XRX200_FDMA_PSTAT1_HDR_PTR, /* Header Pointer */ ++// XRX200_FDMA_TSTAMP0, /* Egress TimeStamp Register 0 */ ++// XRX200_FDMA_TSTAMP0_TSTL, /* Time Stamp [15:0] */ ++// XRX200_FDMA_TSTAMP1, /* Egress TimeStamp Register 1 */ ++// XRX200_FDMA_TSTAMP1_TSTH, /* Time Stamp [31:16] */ ++// XRX200_SDMA_CTRL, /* Ethernet Switch StoreDMA Control Register */ ++// XRX200_SDMA_CTRL_TSTEN, /* Time Stamp Enable */ ++// XRX200_SDMA_FCTHR1, /* SDMA Flow Control Threshold1 Register */ ++// XRX200_SDMA_FCTHR1_THR1, /* Threshold 1 */ ++// XRX200_SDMA_FCTHR2, /* SDMA Flow Control Threshold2 Register */ ++// XRX200_SDMA_FCTHR2_THR2, /* Threshold 2 */ ++// XRX200_SDMA_FCTHR3, /* SDMA Flow Control Threshold3 Register */ ++// XRX200_SDMA_FCTHR3_THR3, /* Threshold 3 */ ++// XRX200_SDMA_FCTHR4, /* SDMA Flow Control Threshold4 Register */ ++// XRX200_SDMA_FCTHR4_THR4, /* Threshold 4 */ ++// XRX200_SDMA_FCTHR5, /* SDMA Flow Control Threshold5 Register */ ++// XRX200_SDMA_FCTHR5_THR5, /* Threshold 5 */ ++// XRX200_SDMA_FCTHR6, /* SDMA Flow Control Threshold6 Register */ ++// XRX200_SDMA_FCTHR6_THR6, /* Threshold 6 */ ++// XRX200_SDMA_FCTHR7, /* SDMA Flow Control Threshold7 Register */ ++// XRX200_SDMA_FCTHR7_THR7, /* Threshold 7 */ ++// XRX200_SDMA_STAT_0, /* SDMA Status Register0 */ ++// XRX200_SDMA_STAT_0_BPS_FILL, /* Back Pressure Status */ ++// XRX200_SDMA_STAT_0_BPS_PNT, /* Back Pressure Status */ ++// XRX200_SDMA_STAT_0_DROP, /* Back Pressure Status */ ++// XRX200_SDMA_STAT_1, /* SDMA Status Register1 */ ++// XRX200_SDMA_STAT_1_FILL, /* Buffer Filling Level */ ++// XRX200_SDMA_STAT_2, /* SDMA Status Register2 */ ++// XRX200_SDMA_STAT_2_FSMS, /* FSM states status */ ++// XRX200_SDMA_IER, /* SDMA Interrupt Enable Register */ ++// XRX200_SDMA_IER_BPEX, /* Buffer Pointers Exceeded */ ++// XRX200_SDMA_IER_BFULL, /* Buffer Full */ ++// XRX200_SDMA_IER_FERR, /* Frame Error */ ++// XRX200_SDMA_IER_FRX, /* Frame Received Successfully */ ++// XRX200_SDMA_ISR, /* SDMA Interrupt Status Register */ ++// XRX200_SDMA_ISR_BPEX, /* Packet Descriptors Exceeded */ ++// XRX200_SDMA_ISR_BFULL, /* Buffer Full */ ++// XRX200_SDMA_ISR_FERR, /* Frame Error */ ++// XRX200_SDMA_ISR_FRX, /* Frame Received Successfully */ ++// XRX200_SDMA_PCTRL, /* Ethernet SwitchStore DMA Port Control Register */ ++// XRX200_SDMA_PCTRL_DTHR, /* Drop Threshold Selection */ ++// XRX200_SDMA_PCTRL_PTHR, /* Pause Threshold Selection */ ++// XRX200_SDMA_PCTRL_PHYEFWD, /* Forward PHY Error Frames */ ++// XRX200_SDMA_PCTRL_ALGFWD, /* Forward Alignment Error Frames */ ++// XRX200_SDMA_PCTRL_LENFWD, /* Forward Length Errored Frames */ ++// XRX200_SDMA_PCTRL_OSFWD, /* Forward Oversized Frames */ ++// XRX200_SDMA_PCTRL_USFWD, /* Forward Undersized Frames */ ++// XRX200_SDMA_PCTRL_FCSIGN, /* Ignore FCS Errors */ ++// XRX200_SDMA_PCTRL_FCSFWD, /* Forward FCS Errored Frames */ ++// XRX200_SDMA_PCTRL_PAUFWD, /* Pause Frame Forwarding */ ++// XRX200_SDMA_PCTRL_MFCEN, /* Metering Flow Control Enable */ ++// XRX200_SDMA_PCTRL_FCEN, /* Flow Control Enable */ ++// XRX200_SDMA_PCTRL_PEN, /* Port Enable */ ++// XRX200_SDMA_PRIO, /* Ethernet SwitchStore DMA Port Priority Register */ ++// XRX200_SDMA_PRIO_PRIO, /* SDMA PRIO */ ++// XRX200_SDMA_PSTAT0_HDR, /* Ethernet SwitchStore DMA Port Status Register 0 */ ++// XRX200_SDMA_PSTAT0_HDR_PTR, /* Port Ingress Queue Header Pointer */ ++// XRX200_SDMA_PSTAT1, /* Ethernet SwitchStore DMA Port Status Register 1 */ ++// XRX200_SDMA_PSTAT1_PPKT, /* Port Ingress Packet Count */ ++// XRX200_SDMA_TSTAMP0, /* Ingress TimeStamp Register 0 */ ++// XRX200_SDMA_TSTAMP0_TSTL, /* Time Stamp [15:0] */ ++// XRX200_SDMA_TSTAMP1, /* Ingress TimeStamp Register 1 */ ++// XRX200_SDMA_TSTAMP1_TSTH, /* Time Stamp [31:16] */ ++}; ++ ++ ++struct xrx200sw_reg { ++ int offset; ++ int shift; ++ int size; ++ int mult; ++} xrx200sw_reg[] = { ++// offeset shift size mult ++// {0x0000, 0, 16, 0x00}, /* XRX200_ETHSW_SWRES Ethernet Switch ResetControl Register */ ++// {0x0000, 1, 1, 0x00}, /* XRX200_ETHSW_SWRES_R1 Hardware Reset */ ++// {0x0000, 0, 1, 0x00}, /* XRX200_ETHSW_SWRES_R0 Register Configuration */ ++// {0x0004, 0, 16, 0x00}, /* XRX200_ETHSW_CLK_MAC_GAT Ethernet Switch Clock ControlRegister */ ++// {0x0004, 12, 4, 0x00}, /* XRX200_ETHSW_CLK_EXP_SLEEP Exponent to put system into sleep */ ++// {0x0004, 8, 4, 0x00}, /* XRX200_ETHSW_CLK_EXP_WAKE Exponent to wake up system */ ++// {0x0004, 7, 1, 0x00}, /* XRX200_ETHSW_CLK_CLK2_EN CLK2 Input for MAC */ ++// {0x0004, 6, 1, 0x00}, /* XRX200_ETHSW_CLK_EXT_DIV_EN External Clock Divider Enable */ ++// {0x0004, 5, 1, 0x00}, /* XRX200_ETHSW_CLK_RAM_DBG_EN Clock Gating Enable */ ++// {0x0004, 4, 1, 0x00}, /* XRX200_ETHSW_CLK_REG_GAT_EN Clock Gating Enable */ ++// {0x0004, 3, 1, 0x00}, /* XRX200_ETHSW_CLK_GAT_EN Clock Gating Enable */ ++// {0x0004, 2, 1, 0x00}, /* XRX200_ETHSW_CLK_MAC_GAT_EN Clock Gating Enable */ ++// {0x0008, 0, 16, 0x00}, /* XRX200_ETHSW_DBG_STEP Ethernet Switch Debug ControlRegister */ ++// {0x0008, 12, 4, 0x00}, /* XRX200_ETHSW_DBG_CLK_SEL Trigger Enable */ ++// {0x0008, 11, 1, 0x00}, /* XRX200_ETHSW_DBG_MON_EN Monitoring Enable */ ++// {0x0008, 9, 2, 0x00}, /* XRX200_ETHSW_DBG_TRIG_EN Trigger Enable */ ++// {0x0008, 8, 1, 0x00}, /* XRX200_ETHSW_DBG_MODE Debug Mode */ ++// {0x0008, 0, 8, 0x00}, /* XRX200_ETHSW_DBG_STEP_TIME Clock Step Size */ ++// {0x000C, 0, 16, 0x00}, /* XRX200_ETHSW_SSB_MODE Ethernet Switch SharedSegment Buffer Mode Register */ ++// {0x000C, 2, 4, 0x00}, /* XRX200_ETHSW_SSB_MODE_ADDE Memory Address */ ++// {0x000C, 0, 2, 0x00}, /* XRX200_ETHSW_SSB_MODE_MODE Memory Access Mode */ ++// {0x0010, 0, 16, 0x00}, /* XRX200_ETHSW_SSB_ADDR Ethernet Switch SharedSegment Buffer Address Register */ ++// {0x0010, 0, 16, 0x00}, /* XRX200_ETHSW_SSB_ADDR_ADDE Memory Address */ ++// {0x0014, 0, 16, 0x00}, /* XRX200_ETHSW_SSB_DATA Ethernet Switch SharedSegment Buffer Data Register */ ++// {0x0014, 0, 16, 0x00}, /* XRX200_ETHSW_SSB_DATA_DATA Data Value */ ++// {0x0018, 0, 16, 0x00}, /* XRX200_ETHSW_CAP_0 Ethernet Switch CapabilityRegister 0 */ ++// {0x0018, 0, 16, 0x00}, /* XRX200_ETHSW_CAP_0_SPEED Clock frequency */ ++// {0x001C, 0, 16, 0x00}, /* XRX200_ETHSW_CAP_1 Ethernet Switch CapabilityRegister 1 */ ++// {0x001C, 15, 1, 0x00}, /* XRX200_ETHSW_CAP_1_GMAC MAC operation mode */ ++// {0x001C, 8, 7, 0x00}, /* XRX200_ETHSW_CAP_1_QUEUE Number of queues */ ++// {0x001C, 4, 4, 0x00}, /* XRX200_ETHSW_CAP_1_VPORTS Number of virtual ports */ ++// {0x001C, 0, 4, 0x00}, /* XRX200_ETHSW_CAP_1_PPORTS Number of physical ports */ ++// {0x0020, 0, 16, 0x00}, /* XRX200_ETHSW_CAP_2 Ethernet Switch CapabilityRegister 2 */ ++// {0x0020, 0, 11, 0x00}, /* XRX200_ETHSW_CAP_2_PACKETS Number of packets */ ++// {0x0024, 0, 16, 0x00}, /* XRX200_ETHSW_CAP_3 Ethernet Switch CapabilityRegister 3 */ ++// {0x0024, 8, 8, 0x00}, /* XRX200_ETHSW_CAP_3_METERS Number of traffic meters */ ++// {0x0024, 0, 8, 0x00}, /* XRX200_ETHSW_CAP_3_SHAPERS Number of traffic shapers */ ++// {0x0028, 0, 16, 0x00}, /* XRX200_ETHSW_CAP_4 Ethernet Switch CapabilityRegister 4 */ ++// {0x0028, 8, 8, 0x00}, /* XRX200_ETHSW_CAP_4_PPPOE PPPoE table size */ ++// {0x0028, 0, 8, 0x00}, /* XRX200_ETHSW_CAP_4_VLAN Active VLAN table size */ ++// {0x002C, 0, 16, 0x00}, /* XRX200_ETHSW_CAP_5 Ethernet Switch CapabilityRegister 5 */ ++// {0x002C, 8, 8, 0x00}, /* XRX200_ETHSW_CAP_5_IPPLEN IP packet length table size */ ++// {0x002C, 0, 8, 0x00}, /* XRX200_ETHSW_CAP_5_PROT Protocol table size */ ++// {0x0030, 0, 16, 0x00}, /* XRX200_ETHSW_CAP_6 Ethernet Switch CapabilityRegister 6 */ ++// {0x0030, 8, 8, 0x00}, /* XRX200_ETHSW_CAP_6_MACDASA MAC DA/SA table size */ ++// {0x0030, 0, 8, 0x00}, /* XRX200_ETHSW_CAP_6_APPL Application table size */ ++// {0x0034, 0, 16, 0x00}, /* XRX200_ETHSW_CAP_7 Ethernet Switch CapabilityRegister 7 */ ++// {0x0034, 8, 8, 0x00}, /* XRX200_ETHSW_CAP_7_IPDASAM IP DA/SA MSB table size */ ++// {0x0034, 0, 8, 0x00}, /* XRX200_ETHSW_CAP_7_IPDASAL IP DA/SA LSB table size */ ++// {0x0038, 0, 16, 0x00}, /* XRX200_ETHSW_CAP_8 Ethernet Switch CapabilityRegister 8 */ ++// {0x0038, 0, 8, 0x00}, /* XRX200_ETHSW_CAP_8_MCAST Multicast table size */ ++// {0x003C, 0, 16, 0x00}, /* XRX200_ETHSW_CAP_9 Ethernet Switch CapabilityRegister 9 */ ++// {0x003C, 0, 8, 0x00}, /* XRX200_ETHSW_CAP_9_FLAGG Flow Aggregation table size */ ++// {0x0040, 0, 16, 0x00}, /* XRX200_ETHSW_CAP_10 Ethernet Switch CapabilityRegister 10 */ ++// {0x0040, 0, 13, 0x00}, /* XRX200_ETHSW_CAP_10_MACBT MAC bridging table size */ ++// {0x0044, 0, 16, 0x00}, /* XRX200_ETHSW_CAP_11 Ethernet Switch CapabilityRegister 11 */ ++// {0x0044, 0, 16, 0x00}, /* XRX200_ETHSW_CAP_11_BSIZEL Packet buffer size (lower part, in byte) */ ++// {0x0048, 0, 16, 0x00}, /* XRX200_ETHSW_CAP_12 Ethernet Switch CapabilityRegister 12 */ ++// {0x0048, 0, 3, 0x00}, /* XRX200_ETHSW_CAP_12_BSIZEH Packet buffer size (higher part, in byte) */ ++// {0x004C, 0, 16, 0x00}, /* XRX200_ETHSW_VERSION_REV Ethernet Switch VersionRegister */ ++// {0x004C, 8, 8, 0x00}, /* XRX200_ETHSW_VERSION_MOD_ID Module Identification */ ++// {0x004C, 0, 8, 0x00}, /* XRX200_ETHSW_VERSION_REV_ID Hardware Revision Identification */ ++// {0x0050, 0, 16, 0x00}, /* XRX200_ETHSW_IER Interrupt Enable Register */ ++// {0x0050, 4, 1, 0x00}, /* XRX200_ETHSW_IER_FDMAIE Fetch DMA Interrupt Enable */ ++// {0x0050, 3, 1, 0x00}, /* XRX200_ETHSW_IER_SDMAIE Store DMA Interrupt Enable */ ++// {0x0050, 2, 1, 0x00}, /* XRX200_ETHSW_IER_MACIE Ethernet MAC Interrupt Enable */ ++// {0x0050, 1, 1, 0x00}, /* XRX200_ETHSW_IER_PCEIE Parser and Classification Engine Interrupt Enable */ ++// {0x0050, 0, 1, 0x00}, /* XRX200_ETHSW_IER_BMIE Buffer Manager Interrupt Enable */ ++// {0x0054, 0, 16, 0x00}, /* XRX200_ETHSW_ISR Interrupt Status Register */ ++// {0x0054, 4, 1, 0x00}, /* XRX200_ETHSW_ISR_FDMAINT Fetch DMA Interrupt */ ++// {0x0054, 3, 1, 0x00}, /* XRX200_ETHSW_ISR_SDMAINT Store DMA Interrupt */ ++// {0x0054, 2, 1, 0x00}, /* XRX200_ETHSW_ISR_MACINT Ethernet MAC Interrupt */ ++// {0x0054, 1, 1, 0x00}, /* XRX200_ETHSW_ISR_PCEINT Parser and Classification Engine Interrupt */ ++// {0x0054, 0, 1, 0x00}, /* XRX200_ETHSW_ISR_BMINT Buffer Manager Interrupt */ ++// {0x0058, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_0 Ethernet Switch SpareCells 0 */ ++// {0x0058, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_0_SPARE SPARE0 */ ++// {0x005C, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_1 Ethernet Switch SpareCells 1 */ ++// {0x005C, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_1_SPARE SPARE1 */ ++// {0x0060, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_2 Ethernet Switch SpareCells 2 */ ++// {0x0060, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_2_SPARE SPARE2 */ ++// {0x0064, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_3 Ethernet Switch SpareCells 3 */ ++// {0x0064, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_3_SPARE SPARE3 */ ++// {0x0068, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_4 Ethernet Switch SpareCells 4 */ ++// {0x0068, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_4_SPARE SPARE4 */ ++// {0x006C, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_5 Ethernet Switch SpareCells 5 */ ++// {0x006C, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_5_SPARE SPARE5 */ ++// {0x0070, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_6 Ethernet Switch SpareCells 6 */ ++// {0x0070, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_6_SPARE SPARE6 */ ++// {0x0074, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_7 Ethernet Switch SpareCells 7 */ ++// {0x0074, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_7_SPARE SPARE7 */ ++// {0x0078, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_8 Ethernet Switch SpareCells 8 */ ++// {0x0078, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_8_SPARE SPARE8 */ ++// {0x007C, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_9 Ethernet Switch SpareCells 9 */ ++// {0x007C, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_9_SPARE SPARE9 */ ++// {0x0080, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_10 Ethernet Switch SpareCells 10 */ ++// {0x0080, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_10_SPARE SPARE10 */ ++// {0x0084, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_11 Ethernet Switch SpareCells 11 */ ++// {0x0084, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_11_SPARE SPARE11 */ ++// {0x0088, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_12 Ethernet Switch SpareCells 12 */ ++// {0x0088, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_12_SPARE SPARE12 */ ++// {0x008C, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_13 Ethernet Switch SpareCells 13 */ ++// {0x008C, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_13_SPARE SPARE13 */ ++// {0x0090, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_14 Ethernet Switch SpareCells 14 */ ++// {0x0090, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_14_SPARE SPARE14 */ ++// {0x0094, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_15 Ethernet Switch SpareCells 15 */ ++// {0x0094, 0, 16, 0x00}, /* XRX200_ETHSW_SPARE_15_SPARE SPARE15 */ ++// {0x0100, 0, 16, 0x00}, /* XRX200_BM_RAM_VAL_3 RAM Value Register 3 */ ++// {0x0100, 0, 16, 0x00}, /* XRX200_BM_RAM_VAL_3_VAL3 Data value [15:0] */ ++// {0x0104, 0, 16, 0x00}, /* XRX200_BM_RAM_VAL_2 RAM Value Register 2 */ ++// {0x0104, 0, 16, 0x00}, /* XRX200_BM_RAM_VAL_2_VAL2 Data value [15:0] */ ++// {0x0108, 0, 16, 0x00}, /* XRX200_BM_RAM_VAL_1 RAM Value Register 1 */ ++// {0x0108, 0, 16, 0x00}, /* XRX200_BM_RAM_VAL_1_VAL1 Data value [15:0] */ ++// {0x010C, 0, 16, 0x00}, /* XRX200_BM_RAM_VAL_0 RAM Value Register 0 */ ++// {0x010C, 0, 16, 0x00}, /* XRX200_BM_RAM_VAL_0_VAL0 Data value [15:0] */ ++// {0x0110, 0, 16, 0x00}, /* XRX200_BM_RAM_ADDR RAM Address Register */ ++// {0x0110, 0, 11, 0x00}, /* XRX200_BM_RAM_ADDR_ADDR RAM Address */ ++// {0x0114, 0, 16, 0x00}, /* XRX200_BM_RAM_CTRL RAM Access Control Register */ ++// {0x0114, 15, 1, 0x00}, /* XRX200_BM_RAM_CTRL_BAS Access Busy/Access Start */ ++// {0x0114, 5, 1, 0x00}, /* XRX200_BM_RAM_CTRL_OPMOD Lookup Table Access Operation Mode */ ++// {0x0114, 0, 5, 0x00}, /* XRX200_BM_RAM_CTRL_ADDR Address for RAM selection */ ++// {0x0118, 0, 16, 0x00}, /* XRX200_BM_FSQM_GCTRL Free Segment Queue ManagerGlobal Control Register */ ++// {0x0118, 0, 10, 0x00}, /* XRX200_BM_FSQM_GCTRL_SEGNUM Maximum Segment Number */ ++// {0x011C, 0, 16, 0x00}, /* XRX200_BM_CONS_SEG Number of Consumed SegmentsRegister */ ++// {0x011C, 0, 10, 0x00}, /* XRX200_BM_CONS_SEG_FSEG Number of Consumed Segments */ ++// {0x0120, 0, 16, 0x00}, /* XRX200_BM_CONS_PKT Number of Consumed PacketPointers Register */ ++// {0x0120, 0, 11, 0x00}, /* XRX200_BM_CONS_PKT_FQP Number of Consumed Packet Pointers */ ++// {0x0124, 0, 16, 0x00}, /* XRX200_BM_GCTRL_F Buffer Manager Global ControlRegister 0 */ ++// {0x0124, 13, 1, 0x00}, /* XRX200_BM_GCTRL_BM_STA Buffer Manager Initialization Status Bit */ ++// {0x0124, 12, 1, 0x00}, /* XRX200_BM_GCTRL_SAT RMON Counter Update Mode */ ++// {0x0124, 11, 1, 0x00}, /* XRX200_BM_GCTRL_FR_RBC Freeze RMON RX Bad Byte 64 Bit Counter */ ++// {0x0124, 10, 1, 0x00}, /* XRX200_BM_GCTRL_FR_RGC Freeze RMON RX Good Byte 64 Bit Counter */ ++// {0x0124, 9, 1, 0x00}, /* XRX200_BM_GCTRL_FR_TGC Freeze RMON TX Good Byte 64 Bit Counter */ ++// {0x0124, 8, 1, 0x00}, /* XRX200_BM_GCTRL_I_FIN RAM initialization finished */ ++// {0x0124, 7, 1, 0x00}, /* XRX200_BM_GCTRL_CX_INI PQM Context RAM initialization */ ++// {0x0124, 6, 1, 0x00}, /* XRX200_BM_GCTRL_FP_INI FPQM RAM initialization */ ++// {0x0124, 5, 1, 0x00}, /* XRX200_BM_GCTRL_FS_INI FSQM RAM initialization */ ++// {0x0124, 4, 1, 0x00}, /* XRX200_BM_GCTRL_R_SRES Software Reset for RMON */ ++// {0x0124, 3, 1, 0x00}, /* XRX200_BM_GCTRL_S_SRES Software Reset for Scheduler */ ++// {0x0124, 2, 1, 0x00}, /* XRX200_BM_GCTRL_A_SRES Software Reset for AVG */ ++// {0x0124, 1, 1, 0x00}, /* XRX200_BM_GCTRL_P_SRES Software Reset for PQM */ ++// {0x0124, 0, 1, 0x00}, /* XRX200_BM_GCTRL_F_SRES Software Reset for FSQM */ ++// {0x0128, 0, 16, 0x00}, /* XRX200_BM_QUEUE_GCTRL Queue Manager GlobalControl Register 0 */ ++ {0x0128, 10, 1, 0x00}, /* XRX200_BM_QUEUE_GCTRL_GL_MOD WRED Mode Signal */ ++// {0x0128, 7, 3, 0x00}, /* XRX200_BM_QUEUE_GCTRL_AQUI Average Queue Update Interval */ ++// {0x0128, 3, 4, 0x00}, /* XRX200_BM_QUEUE_GCTRL_AQWF Average Queue Weight Factor */ ++// {0x0128, 2, 1, 0x00}, /* XRX200_BM_QUEUE_GCTRL_QAVGEN Queue Average Calculation Enable */ ++// {0x0128, 0, 2, 0x00}, /* XRX200_BM_QUEUE_GCTRL_DPROB Drop Probability Profile */ ++// {0x012C, 0, 16, 0x00}, /* XRX200_BM_WRED_RTH_0 WRED Red Threshold Register0 */ ++// {0x012C, 0, 10, 0x00}, /* XRX200_BM_WRED_RTH_0_MINTH Minimum Threshold */ ++// {0x0130, 0, 16, 0x00}, /* XRX200_BM_WRED_RTH_1 WRED Red Threshold Register1 */ ++// {0x0130, 0, 10, 0x00}, /* XRX200_BM_WRED_RTH_1_MAXTH Maximum Threshold */ ++// {0x0134, 0, 16, 0x00}, /* XRX200_BM_WRED_YTH_0 WRED Yellow ThresholdRegister 0 */ ++// {0x0134, 0, 10, 0x00}, /* XRX200_BM_WRED_YTH_0_MINTH Minimum Threshold */ ++// {0x0138, 0, 16, 0x00}, /* XRX200_BM_WRED_YTH_1 WRED Yellow ThresholdRegister 1 */ ++// {0x0138, 0, 10, 0x00}, /* XRX200_BM_WRED_YTH_1_MAXTH Maximum Threshold */ ++// {0x013C, 0, 16, 0x00}, /* XRX200_BM_WRED_GTH_0 WRED Green ThresholdRegister 0 */ ++// {0x013C, 0, 10, 0x00}, /* XRX200_BM_WRED_GTH_0_MINTH Minimum Threshold */ ++// {0x0140, 0, 16, 0x00}, /* XRX200_BM_WRED_GTH_1 WRED Green ThresholdRegister 1 */ ++// {0x0140, 0, 10, 0x00}, /* XRX200_BM_WRED_GTH_1_MAXTH Maximum Threshold */ ++// {0x0144, 0, 16, 0x00}, /* XRX200_BM_DROP_GTH_0_THR Drop Threshold ConfigurationRegister 0 */ ++// {0x0144, 0, 11, 0x00}, /* XRX200_BM_DROP_GTH_0_THR_FQ Threshold for frames marked red */ ++// {0x0148, 0, 16, 0x00}, /* XRX200_BM_DROP_GTH_1_THY Drop Threshold ConfigurationRegister 1 */ ++// {0x0148, 0, 11, 0x00}, /* XRX200_BM_DROP_GTH_1_THY_FQ Threshold for frames marked yellow */ ++// {0x014C, 0, 16, 0x00}, /* XRX200_BM_DROP_GTH_2_THG Drop Threshold ConfigurationRegister 2 */ ++// {0x014C, 0, 11, 0x00}, /* XRX200_BM_DROP_GTH_2_THG_FQ Threshold for frames marked green */ ++// {0x0150, 0, 16, 0x00}, /* XRX200_BM_IER Buffer Manager Global InterruptEnable Register */ ++// {0x0150, 7, 1, 0x00}, /* XRX200_BM_IER_CNT4 Counter Group 4 (RMON-CLASSIFICATION) Interrupt Enable */ ++// {0x0150, 6, 1, 0x00}, /* XRX200_BM_IER_CNT3 Counter Group 3 (RMON-PQM) Interrupt Enable */ ++// {0x0150, 5, 1, 0x00}, /* XRX200_BM_IER_CNT2 Counter Group 2 (RMON-SCHEDULER) Interrupt Enable */ ++// {0x0150, 4, 1, 0x00}, /* XRX200_BM_IER_CNT1 Counter Group 1 (RMON-QFETCH) Interrupt Enable */ ++// {0x0150, 3, 1, 0x00}, /* XRX200_BM_IER_CNT0 Counter Group 0 (RMON-QSTOR) Interrupt Enable */ ++// {0x0150, 2, 1, 0x00}, /* XRX200_BM_IER_DEQ PQM dequeue Interrupt Enable */ ++// {0x0150, 1, 1, 0x00}, /* XRX200_BM_IER_ENQ PQM Enqueue Interrupt Enable */ ++// {0x0150, 0, 1, 0x00}, /* XRX200_BM_IER_FSQM Buffer Empty Interrupt Enable */ ++// {0x0154, 0, 16, 0x00}, /* XRX200_BM_ISR Buffer Manager Global InterruptStatus Register */ ++// {0x0154, 7, 1, 0x00}, /* XRX200_BM_ISR_CNT4 Counter Group 4 Interrupt */ ++// {0x0154, 6, 1, 0x00}, /* XRX200_BM_ISR_CNT3 Counter Group 3 Interrupt */ ++// {0x0154, 5, 1, 0x00}, /* XRX200_BM_ISR_CNT2 Counter Group 2 Interrupt */ ++// {0x0154, 4, 1, 0x00}, /* XRX200_BM_ISR_CNT1 Counter Group 1 Interrupt */ ++// {0x0154, 3, 1, 0x00}, /* XRX200_BM_ISR_CNT0 Counter Group 0 Interrupt */ ++// {0x0154, 2, 1, 0x00}, /* XRX200_BM_ISR_DEQ PQM dequeue Interrupt Enable */ ++// {0x0154, 1, 1, 0x00}, /* XRX200_BM_ISR_ENQ PQM Enqueue Interrupt */ ++// {0x0154, 0, 1, 0x00}, /* XRX200_BM_ISR_FSQM Buffer Empty Interrupt */ ++// {0x0158, 0, 16, 0x00}, /* XRX200_BM_CISEL Buffer Manager RMON CounterInterrupt Select Register */ ++// {0x0158, 0, 3, 0x00}, /* XRX200_BM_CISEL_PORT Port Number */ ++// {0x015C, 0, 16, 0x00}, /* XRX200_BM_DEBUG_CTRL_DBG Debug Control Register */ ++// {0x015C, 0, 8, 0x00}, /* XRX200_BM_DEBUG_CTRL_DBG_SEL Select Signal for Debug Multiplexer */ ++// {0x0160, 0, 16, 0x00}, /* XRX200_BM_DEBUG_VAL_DBG Debug Value Register */ ++// {0x0160, 0, 16, 0x00}, /* XRX200_BM_DEBUG_VAL_DBG_DAT Debug Data Value */ ++// {0x0200, 0, 16, 0x08}, /* XRX200_BM_PCFG Buffer Manager PortConfiguration Register */ ++// {0x0200, 0, 1, 0x08}, /* XRX200_BM_PCFG_CNTEN RMON Counter Enable */ ++// {0x0204, 0, 16, 0x08}, /* XRX200_BM_RMON_CTRL_RAM1 Buffer ManagerRMON Control Register */ ++// {0x0204, 1, 1, 0x08}, /* XRX200_BM_RMON_CTRL_RAM2_RES Software Reset for RMON RAM2 */ ++// {0x0204, 0, 1, 0x08}, /* XRX200_BM_RMON_CTRL_RAM1_RES Software Reset for RMON RAM1 */ ++// {0x0400, 0, 16, 0x08}, /* XRX200_PQM_DP Packet Queue ManagerDrop Probability Register */ ++// {0x0400, 0, 2, 0x08}, /* XRX200_PQM_DP_DPROB Drop Probability Profile */ ++// {0x0404, 0, 16, 0x08}, /* XRX200_PQM_RS Packet Queue ManagerRate Shaper Assignment Register */ ++// {0x0404, 15, 1, 0x08}, /* XRX200_PQM_RS_EN2 Rate Shaper 2 Enable */ ++// {0x0404, 8, 6, 0x08}, /* XRX200_PQM_RS_RS2 Rate Shaper 2 */ ++// {0x0404, 7, 1, 0x08}, /* XRX200_PQM_RS_EN1 Rate Shaper 1 Enable */ ++// {0x0404, 0, 6, 0x08}, /* XRX200_PQM_RS_RS1 Rate Shaper 1 */ ++// {0x0500, 0, 16, 0x14}, /* XRX200_RS_CTRL Rate Shaper ControlRegister */ ++// {0x0500, 0, 1, 0x14}, /* XRX200_RS_CTRL_RSEN Rate Shaper Enable */ ++// {0x0504, 0, 16, 0x14}, /* XRX200_RS_CBS Rate Shaper CommittedBurst Size Register */ ++// {0x0504, 0, 10, 0x14}, /* XRX200_RS_CBS_CBS Committed Burst Size */ ++// {0x0508, 0, 16, 0x14}, /* XRX200_RS_IBS Rate Shaper InstantaneousBurst Size Register */ ++// {0x0508, 0, 2, 0x14}, /* XRX200_RS_IBS_IBS Instantaneous Burst Size */ ++// {0x050C, 0, 16, 0x14}, /* XRX200_RS_CIR_EXP Rate Shaper RateExponent Register */ ++// {0x050C, 0, 4, 0x14}, /* XRX200_RS_CIR_EXP_EXP Exponent */ ++// {0x0510, 0, 16, 0x14}, /* XRX200_RS_CIR_MANT Rate Shaper RateMantissa Register */ ++// {0x0510, 0, 10, 0x14}, /* XRX200_RS_CIR_MANT_MANT Mantissa */ ++ {0x1100, 0, 16, 0x00}, /* XRX200_PCE_TBL_KEY_7 Table Key Data 7 */ ++// {0x1100, 0, 16, 0x00}, /* XRX200_PCE_TBL_KEY_7_KEY7 Key Value[15:0] */ ++ {0x1104, 0, 16, 0x00}, /* XRX200_PCE_TBL_KEY_6 Table Key Data 6 */ ++// {0x1104, 0, 16, 0x00}, /* XRX200_PCE_TBL_KEY_6_KEY6 Key Value[15:0] */ ++ {0x1108, 0, 16, 0x00}, /* XRX200_PCE_TBL_KEY_5 Table Key Data 5 */ ++// {0x1108, 0, 16, 0x00}, /* XRX200_PCE_TBL_KEY_5_KEY5 Key Value[15:0] */ ++ {0x110C, 0, 16, 0x00}, /* XRX200_PCE_TBL_KEY_4 Table Key Data 4 */ ++// {0x110C, 0, 16, 0x00}, /* XRX200_PCE_TBL_KEY_4_KEY4 Key Value[15:0] */ ++ {0x1110, 0, 16, 0x00}, /* XRX200_PCE_TBL_KEY_3 Table Key Data 3 */ ++// {0x1110, 0, 16, 0x00}, /* XRX200_PCE_TBL_KEY_3_KEY3 Key Value[15:0] */ ++ {0x1114, 0, 16, 0x00}, /* XRX200_PCE_TBL_KEY_2 Table Key Data 2 */ ++// {0x1114, 0, 16, 0x00}, /* XRX200_PCE_TBL_KEY_2_KEY2 Key Value[15:0] */ ++ {0x1118, 0, 16, 0x00}, /* XRX200_PCE_TBL_KEY_1 Table Key Data 1 */ ++// {0x1118, 0, 16, 0x00}, /* XRX200_PCE_TBL_KEY_1_KEY1 Key Value[31:16] */ ++ {0x111C, 0, 16, 0x00}, /* XRX200_PCE_TBL_KEY_0 Table Key Data 0 */ ++// {0x111C, 0, 16, 0x00}, /* XRX200_PCE_TBL_KEY_0_KEY0 Key Value[15:0] */ ++ {0x1120, 0, 16, 0x00}, /* XRX200_PCE_TBL_MASK_0 Table Mask Write Register0 */ ++// {0x1120, 0, 16, 0x00}, /* XRX200_PCE_TBL_MASK_0_MASK0 Mask Pattern [15:0] */ ++ {0x1124, 0, 16, 0x00}, /* XRX200_PCE_TBL_VAL_4 Table Value Register4 */ ++// {0x1124, 0, 16, 0x00}, /* XRX200_PCE_TBL_VAL_4_VAL4 Data value [15:0] */ ++ {0x1128, 0, 16, 0x00}, /* XRX200_PCE_TBL_VAL_3 Table Value Register3 */ ++// {0x1128, 0, 16, 0x00}, /* XRX200_PCE_TBL_VAL_3_VAL3 Data value [15:0] */ ++ {0x112C, 0, 16, 0x00}, /* XRX200_PCE_TBL_VAL_2 Table Value Register2 */ ++// {0x112C, 0, 16, 0x00}, /* XRX200_PCE_TBL_VAL_2_VAL2 Data value [15:0] */ ++ {0x1130, 0, 16, 0x00}, /* XRX200_PCE_TBL_VAL_1 Table Value Register1 */ ++// {0x1130, 0, 16, 0x00}, /* XRX200_PCE_TBL_VAL_1_VAL1 Data value [15:0] */ ++ {0x1134, 0, 16, 0x00}, /* XRX200_PCE_TBL_VAL_0 Table Value Register0 */ ++// {0x1134, 0, 16, 0x00}, /* XRX200_PCE_TBL_VAL_0_VAL0 Data value [15:0] */ ++// {0x1138, 0, 16, 0x00}, /* XRX200_PCE_TBL_ADDR Table Entry AddressRegister */ ++ {0x1138, 0, 11, 0x00}, /* XRX200_PCE_TBL_ADDR_ADDR Table Address */ ++// {0x113C, 0, 16, 0x00}, /* XRX200_PCE_TBL_CTRL Table Access ControlRegister */ ++ {0x113C, 15, 1, 0x00}, /* XRX200_PCE_TBL_CTRL_BAS Access Busy/Access Start */ ++ {0x113C, 13, 1, 0x00}, /* XRX200_PCE_TBL_CTRL_TYPE Lookup Entry Type */ ++ {0x113C, 12, 1, 0x00}, /* XRX200_PCE_TBL_CTRL_VLD Lookup Entry Valid */ ++ {0x113C, 7, 4, 0x00}, /* XRX200_PCE_TBL_CTRL_GMAP Group Map */ ++ {0x113C, 5, 2, 0x00}, /* XRX200_PCE_TBL_CTRL_OPMOD Lookup Table Access Operation Mode */ ++ {0x113C, 0, 5, 0x00}, /* XRX200_PCE_TBL_CTRL_ADDR Lookup Table Address */ ++// {0x1140, 0, 16, 0x00}, /* XRX200_PCE_TBL_STAT Table General StatusRegister */ ++// {0x1140, 2, 1, 0x00}, /* XRX200_PCE_TBL_STAT_TBUSY Table Access Busy */ ++// {0x1140, 1, 1, 0x00}, /* XRX200_PCE_TBL_STAT_TEMPT Table Empty */ ++// {0x1140, 0, 1, 0x00}, /* XRX200_PCE_TBL_STAT_TFUL Table Full */ ++// {0x1144, 0, 16, 0x00}, /* XRX200_PCE_AGE_0 Aging Counter ConfigurationRegister 0 */ ++// {0x1144, 0, 4, 0x00}, /* XRX200_PCE_AGE_0_EXP Aging Counter Exponent Value */ ++// {0x1148, 0, 16, 0x00}, /* XRX200_PCE_AGE_1 Aging Counter ConfigurationRegister 1 */ ++// {0x1148, 0, 16, 0x00}, /* XRX200_PCE_AGE_1_MANT Aging Counter Mantissa Value */ ++// {0x114C, 0, 16, 0x00}, /* XRX200_PCE_PMAP_1 Port Map Register 1 */ ++// {0x114C, 0, 16, 0x00}, /* XRX200_PCE_PMAP_1_MPMAP Monitoring Port Map */ ++// {0x1150, 0, 16, 0x00}, /* XRX200_PCE_PMAP_2 Port Map Register 2 */ ++// {0x1150, 0, 16, 0x00}, /* XRX200_PCE_PMAP_2_DMCPMAP Default Multicast Port Map */ ++// {0x1154, 0, 16, 0x00}, /* XRX200_PCE_PMAP_3 Port Map Register 3 */ ++// {0x1154, 0, 16, 0x00}, /* XRX200_PCE_PMAP_3_UUCMAP Default Unknown Unicast Port Map */ ++// {0x1158, 0, 16, 0x00}, /* XRX200_PCE_GCTRL_0 PCE Global Control Register0 */ ++// {0x1158, 15, 1, 0x00}, /* XRX200_PCE_GCTRL_0_IGMP IGMP Mode Selection */ ++ {0x1158, 14, 1, 0x00}, /* XRX200_PCE_GCTRL_0_VLAN VLAN-aware Switching */ ++// {0x1158, 13, 1, 0x00}, /* XRX200_PCE_GCTRL_0_NOPM No Port Map Forwarding */ ++// {0x1158, 12, 1, 0x00}, /* XRX200_PCE_GCTRL_0_SCONUC Unknown Unicast Storm Control */ ++// {0x1158, 11, 1, 0x00}, /* XRX200_PCE_GCTRL_0_SCONMC Multicast Storm Control */ ++// {0x1158, 10, 1, 0x00}, /* XRX200_PCE_GCTRL_0_SCONBC Broadcast Storm Control */ ++// {0x1158, 8, 2, 0x00}, /* XRX200_PCE_GCTRL_0_SCONMOD Storm Control Mode */ ++// {0x1158, 4, 4, 0x00}, /* XRX200_PCE_GCTRL_0_SCONMET Storm Control Metering Instance */ ++// {0x1158, 3, 1, 0x00}, /* XRX200_PCE_GCTRL_0_MC_VALID Access Request */ ++// {0x1158, 2, 1, 0x00}, /* XRX200_PCE_GCTRL_0_PLCKMOD Port Lock Mode */ ++// {0x1158, 1, 1, 0x00}, /* XRX200_PCE_GCTRL_0_PLIMMOD MAC Address Learning Limitation Mode */ ++// {0x1158, 0, 1, 0x00}, /* XRX200_PCE_GCTRL_0_MTFL MAC Table Flushing */ ++// {0x115C, 0, 16, 0x00}, /* XRX200_PCE_GCTRL_1 PCE Global Control Register1 */ ++// {0x115C, 1, 1, 0x00}, /* XRX200_PCE_GCTRL_1_PCE_DIS PCE Disable after currently processed packet */ ++// {0x115C, 0, 1, 0x00}, /* XRX200_PCE_GCTRL_1_LRNMOD MAC Address Learning Mode */ ++// {0x1160, 0, 16, 0x00}, /* XRX200_PCE_TCM_GLOB_CTRL Three-color MarkerGlobal Control Register */ ++// {0x1160, 6, 3, 0x00}, /* XRX200_PCE_TCM_GLOB_CTRL_DPRED Re-marking Drop Precedence Red Encoding */ ++// {0x1160, 3, 3, 0x00}, /* XRX200_PCE_TCM_GLOB_CTRL_DPYEL Re-marking Drop Precedence Yellow Encoding */ ++// {0x1160, 0, 3, 0x00}, /* XRX200_PCE_TCM_GLOB_CTRL_DPGRN Re-marking Drop Precedence Green Encoding */ ++// {0x1164, 0, 16, 0x00}, /* XRX200_PCE_IGMP_CTRL IGMP Control Register */ ++// {0x1164, 15, 1, 0x00}, /* XRX200_PCE_IGMP_CTRL_FAGEEN Force Aging of Table Entries Enable */ ++// {0x1164, 14, 1, 0x00}, /* XRX200_PCE_IGMP_CTRL_FLEAVE Fast Leave Enable */ ++// {0x1164, 13, 1, 0x00}, /* XRX200_PCE_IGMP_CTRL_DMRTEN Default Maximum Response Time Enable */ ++// {0x1164, 12, 1, 0x00}, /* XRX200_PCE_IGMP_CTRL_JASUP Join Aggregation Suppression Enable */ ++// {0x1164, 11, 1, 0x00}, /* XRX200_PCE_IGMP_CTRL_REPSUP Report Suppression Enable */ ++// {0x1164, 10, 1, 0x00}, /* XRX200_PCE_IGMP_CTRL_SRPEN Snooping of Router Port Enable */ ++// {0x1164, 8, 2, 0x00}, /* XRX200_PCE_IGMP_CTRL_ROB Robustness Variable */ ++// {0x1164, 0, 8, 0x00}, /* XRX200_PCE_IGMP_CTRL_DMRT IGMP Default Maximum Response Time */ ++// {0x1168, 0, 16, 0x00}, /* XRX200_PCE_IGMP_DRPM IGMP Default RouterPort Map Register */ ++// {0x1168, 0, 16, 0x00}, /* XRX200_PCE_IGMP_DRPM_DRPM IGMP Default Router Port Map */ ++// {0x116C, 0, 16, 0x00}, /* XRX200_PCE_IGMP_AGE_0 IGMP Aging Register0 */ ++// {0x116C, 3, 8, 0x00}, /* XRX200_PCE_IGMP_AGE_0_MANT IGMP Group Aging Time Mantissa */ ++// {0x116C, 0, 3, 0x00}, /* XRX200_PCE_IGMP_AGE_0_EXP IGMP Group Aging Time Exponent */ ++// {0x1170, 0, 16, 0x00}, /* XRX200_PCE_IGMP_AGE_1 IGMP Aging Register1 */ ++// {0x1170, 0, 12, 0x00}, /* XRX200_PCE_IGMP_AGE_1_MANT IGMP Router Port Aging Time Mantissa */ ++// {0x1174, 0, 16, 0x00}, /* XRX200_PCE_IGMP_STAT IGMP Status Register */ ++// {0x1174, 0, 16, 0x00}, /* XRX200_PCE_IGMP_STAT_IGPM IGMP Port Map */ ++// {0x1178, 0, 16, 0x00}, /* XRX200_WOL_GLB_CTRL Wake-on-LAN ControlRegister */ ++// {0x1178, 0, 1, 0x00}, /* XRX200_WOL_GLB_CTRL_PASSEN WoL Password Enable */ ++// {0x117C, 0, 16, 0x00}, /* XRX200_WOL_DA_0 Wake-on-LAN DestinationAddress Register 0 */ ++// {0x117C, 0, 16, 0x00}, /* XRX200_WOL_DA_0_DA0 WoL Destination Address [15:0] */ ++// {0x1180, 0, 16, 0x00}, /* XRX200_WOL_DA_1 Wake-on-LAN DestinationAddress Register 1 */ ++// {0x1180, 0, 16, 0x00}, /* XRX200_WOL_DA_1_DA1 WoL Destination Address [31:16] */ ++// {0x1184, 0, 16, 0x00}, /* XRX200_WOL_DA_2 Wake-on-LAN DestinationAddress Register 2 */ ++// {0x1184, 0, 16, 0x00}, /* XRX200_WOL_DA_2_DA2 WoL Destination Address [47:32] */ ++// {0x1188, 0, 16, 0x00}, /* XRX200_WOL_PW_0 Wake-on-LAN Password Register0 */ ++// {0x1188, 0, 16, 0x00}, /* XRX200_WOL_PW_0_PW0 WoL Password [15:0] */ ++// {0x118C, 0, 16, 0x00}, /* XRX200_WOL_PW_1 Wake-on-LAN Password Register1 */ ++// {0x118C, 0, 16, 0x00}, /* XRX200_WOL_PW_1_PW1 WoL Password [31:16] */ ++// {0x1190, 0, 16, 0x00}, /* XRX200_WOL_PW_2 Wake-on-LAN Password Register2 */ ++// {0x1190, 0, 16, 0x00}, /* XRX200_WOL_PW_2_PW2 WoL Password [47:32] */ ++// {0x1194, 0, 16, 0x00}, /* XRX200_PCE_IER_0_PINT Parser and ClassificationEngine Global Interrupt Enable Register 0 */ ++// {0x1194, 15, 1, 0x00}, /* XRX200_PCE_IER_0_PINT_15 Port Interrupt Enable */ ++// {0x1194, 14, 1, 0x00}, /* XRX200_PCE_IER_0_PINT_14 Port Interrupt Enable */ ++// {0x1194, 13, 1, 0x00}, /* XRX200_PCE_IER_0_PINT_13 Port Interrupt Enable */ ++// {0x1194, 12, 1, 0x00}, /* XRX200_PCE_IER_0_PINT_12 Port Interrupt Enable */ ++// {0x1194, 11, 1, 0x00}, /* XRX200_PCE_IER_0_PINT_11 Port Interrupt Enable */ ++// {0x1194, 10, 1, 0x00}, /* XRX200_PCE_IER_0_PINT_10 Port Interrupt Enable */ ++// {0x1194, 9, 1, 0x00}, /* XRX200_PCE_IER_0_PINT_9 Port Interrupt Enable */ ++// {0x1194, 8, 1, 0x00}, /* XRX200_PCE_IER_0_PINT_8 Port Interrupt Enable */ ++// {0x1194, 7, 1, 0x00}, /* XRX200_PCE_IER_0_PINT_7 Port Interrupt Enable */ ++// {0x1194, 6, 1, 0x00}, /* XRX200_PCE_IER_0_PINT_6 Port Interrupt Enable */ ++// {0x1194, 5, 1, 0x00}, /* XRX200_PCE_IER_0_PINT_5 Port Interrupt Enable */ ++// {0x1194, 4, 1, 0x00}, /* XRX200_PCE_IER_0_PINT_4 Port Interrupt Enable */ ++// {0x1194, 3, 1, 0x00}, /* XRX200_PCE_IER_0_PINT_3 Port Interrupt Enable */ ++// {0x1194, 2, 1, 0x00}, /* XRX200_PCE_IER_0_PINT_2 Port Interrupt Enable */ ++// {0x1194, 1, 1, 0x00}, /* XRX200_PCE_IER_0_PINT_1 Port Interrupt Enable */ ++// {0x1194, 0, 1, 0x00}, /* XRX200_PCE_IER_0_PINT_0 Port Interrupt Enable */ ++// {0x1198, 0, 16, 0x00}, /* XRX200_PCE_IER_1 Parser and ClassificationEngine Global Interrupt Enable Register 1 */ ++// {0x1198, 6, 1, 0x00}, /* XRX200_PCE_IER_1_FLOWINT Traffic Flow Table Interrupt Rule matched Interrupt Enable */ ++// {0x1198, 5, 1, 0x00}, /* XRX200_PCE_IER_1_CPH2 Classification Phase 2 Ready Interrupt Enable */ ++// {0x1198, 4, 1, 0x00}, /* XRX200_PCE_IER_1_CPH1 Classification Phase 1 Ready Interrupt Enable */ ++// {0x1198, 3, 1, 0x00}, /* XRX200_PCE_IER_1_CPH0 Classification Phase 0 Ready Interrupt Enable */ ++// {0x1198, 2, 1, 0x00}, /* XRX200_PCE_IER_1_PRDY Parser Ready Interrupt Enable */ ++// {0x1198, 1, 1, 0x00}, /* XRX200_PCE_IER_1_IGTF IGMP Table Full Interrupt Enable */ ++// {0x1198, 0, 1, 0x00}, /* XRX200_PCE_IER_1_MTF MAC Table Full Interrupt Enable */ ++// {0x119C, 0, 16, 0x00}, /* XRX200_PCE_ISR_0_PINT Parser and ClassificationEngine Global Interrupt Status Register 0 */ ++// {0x119C, 15, 1, 0x00}, /* XRX200_PCE_ISR_0_PINT_15 Port Interrupt */ ++// {0x119C, 14, 1, 0x00}, /* XRX200_PCE_ISR_0_PINT_14 Port Interrupt */ ++// {0x119C, 13, 1, 0x00}, /* XRX200_PCE_ISR_0_PINT_13 Port Interrupt */ ++// {0x119C, 12, 1, 0x00}, /* XRX200_PCE_ISR_0_PINT_12 Port Interrupt */ ++// {0x119C, 11, 1, 0x00}, /* XRX200_PCE_ISR_0_PINT_11 Port Interrupt */ ++// {0x119C, 10, 1, 0x00}, /* XRX200_PCE_ISR_0_PINT_10 Port Interrupt */ ++// {0x119C, 9, 1, 0x00}, /* XRX200_PCE_ISR_0_PINT_9 Port Interrupt */ ++// {0x119C, 8, 1, 0x00}, /* XRX200_PCE_ISR_0_PINT_8 Port Interrupt */ ++// {0x119C, 7, 1, 0x00}, /* XRX200_PCE_ISR_0_PINT_7 Port Interrupt */ ++// {0x119C, 6, 1, 0x00}, /* XRX200_PCE_ISR_0_PINT_6 Port Interrupt */ ++// {0x119C, 5, 1, 0x00}, /* XRX200_PCE_ISR_0_PINT_5 Port Interrupt */ ++// {0x119C, 4, 1, 0x00}, /* XRX200_PCE_ISR_0_PINT_4 Port Interrupt */ ++// {0x119C, 3, 1, 0x00}, /* XRX200_PCE_ISR_0_PINT_3 Port Interrupt */ ++// {0x119C, 2, 1, 0x00}, /* XRX200_PCE_ISR_0_PINT_2 Port Interrupt */ ++// {0x119C, 1, 1, 0x00}, /* XRX200_PCE_ISR_0_PINT_1 Port Interrupt */ ++// {0x119C, 0, 1, 0x00}, /* XRX200_PCE_ISR_0_PINT_0 Port Interrupt */ ++// {0x11A0, 0, 16, 0x00}, /* XRX200_PCE_ISR_1 Parser and ClassificationEngine Global Interrupt Status Register 1 */ ++// {0x11A0, 6, 1, 0x00}, /* XRX200_PCE_ISR_1_FLOWINT Traffic Flow Table Interrupt Rule matched */ ++// {0x11A0, 5, 1, 0x00}, /* XRX200_PCE_ISR_1_CPH2 Classification Phase 2 Ready Interrupt */ ++// {0x11A0, 4, 1, 0x00}, /* XRX200_PCE_ISR_1_CPH1 Classification Phase 1 Ready Interrupt */ ++// {0x11A0, 3, 1, 0x00}, /* XRX200_PCE_ISR_1_CPH0 Classification Phase 0 Ready Interrupt */ ++// {0x11A0, 2, 1, 0x00}, /* XRX200_PCE_ISR_1_PRDY Parser Ready Interrupt */ ++// {0x11A0, 1, 1, 0x00}, /* XRX200_PCE_ISR_1_IGTF IGMP Table Full Interrupt */ ++// {0x11A0, 0, 1, 0x00}, /* XRX200_PCE_ISR_1_MTF MAC Table Full Interrupt */ ++// {0x11A4, 0, 16, 0x00}, /* XRX200_PARSER_STAT_FIFO Parser Status Register */ ++// {0x11A4, 8, 8, 0x00}, /* XRX200_PARSER_STAT_FSM_DAT_CNT Parser FSM Data Counter */ ++// {0x11A4, 5, 3, 0x00}, /* XRX200_PARSER_STAT_FSM_STATE Parser FSM State */ ++// {0x11A4, 4, 1, 0x00}, /* XRX200_PARSER_STAT_PKT_ERR Packet error detected */ ++// {0x11A4, 3, 1, 0x00}, /* XRX200_PARSER_STAT_FSM_FIN Parser FSM finished */ ++// {0x11A4, 2, 1, 0x00}, /* XRX200_PARSER_STAT_FSM_START Parser FSM start */ ++// {0x11A4, 1, 1, 0x00}, /* XRX200_PARSER_STAT_FIFO_RDY Parser FIFO ready for read. */ ++// {0x11A4, 0, 1, 0x00}, /* XRX200_PARSER_STAT_FIFO_FULL Parser */ ++// {0x1200, 0, 16, 0x28}, /* XRX200_PCE_PCTRL_0 PCE Port ControlRegister 0 */ ++// {0x1200, 13, 1, 0x28}, /* XRX200_PCE_PCTRL_0_MCST Multicast Forwarding Mode Selection */ ++// {0x1200, 12, 1, 0x28}, /* XRX200_PCE_PCTRL_0_EGSTEN Table-based Egress Special Tag Enable */ ++// {0x1200, 11, 1, 0x28}, /* XRX200_PCE_PCTRL_0_IGSTEN Ingress Special Tag Enable */ ++// {0x1200, 10, 1, 0x28}, /* XRX200_PCE_PCTRL_0_PCPEN PCP Remarking Mode */ ++// {0x1200, 9, 1, 0x28}, /* XRX200_PCE_PCTRL_0_CLPEN Class Remarking Mode */ ++// {0x1200, 8, 1, 0x28}, /* XRX200_PCE_PCTRL_0_DPEN Drop Precedence Remarking Mode */ ++// {0x1200, 7, 1, 0x28}, /* XRX200_PCE_PCTRL_0_CMOD Three-color Marker Color Mode */ ++// {0x1200, 6, 1, 0x28}, /* XRX200_PCE_PCTRL_0_VREP VLAN Replacement Mode */ ++ {0x1200, 5, 1, 0x28}, /* XRX200_PCE_PCTRL_0_TVM Transparent VLAN Mode */ ++// {0x1200, 4, 1, 0x28}, /* XRX200_PCE_PCTRL_0_PLOCK Port Locking Enable */ ++// {0x1200, 3, 1, 0x28}, /* XRX200_PCE_PCTRL_0_AGEDIS Aging Disable */ ++// {0x1200, 0, 3, 0x28}, /* XRX200_PCE_PCTRL_0_PSTATE Port State */ ++// {0x1204, 0, 16, 0x28}, /* XRX200_PCE_PCTRL_1 PCE Port ControlRegister 1 */ ++// {0x1204, 0, 8, 0x28}, /* XRX200_PCE_PCTRL_1_LRNLIM MAC Address Learning Limit */ ++// {0x1208, 0, 16, 0x28}, /* XRX200_PCE_PCTRL_2 PCE Port ControlRegister 2 */ ++// {0x1208, 7, 1, 0x28}, /* XRX200_PCE_PCTRL_2_DSCPMOD DSCP Mode Selection */ ++// {0x1208, 5, 2, 0x28}, /* XRX200_PCE_PCTRL_2_DSCP Enable DSCP to select the Class of Service */ ++// {0x1208, 4, 1, 0x28}, /* XRX200_PCE_PCTRL_2_PCP Enable VLAN PCP to select the Class of Service */ ++// {0x1208, 0, 4, 0x28}, /* XRX200_PCE_PCTRL_2_PCLASS Port-based Traffic Class */ ++// {0x120C, 0, 16, 0x28}, /* XRX200_PCE_PCTRL_3_VIO PCE Port ControlRegister 3 */ ++// {0x120C, 11, 1, 0x28}, /* XRX200_PCE_PCTRL_3_EDIR Egress Redirection Mode */ ++// {0x120C, 10, 1, 0x28}, /* XRX200_PCE_PCTRL_3_RXDMIR Receive Mirroring Enable for dropped frames */ ++// {0x120C, 9, 1, 0x28}, /* XRX200_PCE_PCTRL_3_RXVMIR Receive Mirroring Enable for valid frames */ ++// {0x120C, 8, 1, 0x28}, /* XRX200_PCE_PCTRL_3_TXMIR Transmit Mirroring Enable */ ++// {0x120C, 7, 1, 0x28}, /* XRX200_PCE_PCTRL_3_VIO_7 Violation Type 7 Mirroring Enable */ ++// {0x120C, 6, 1, 0x28}, /* XRX200_PCE_PCTRL_3_VIO_6 Violation Type 6 Mirroring Enable */ ++// {0x120C, 5, 1, 0x28}, /* XRX200_PCE_PCTRL_3_VIO_5 Violation Type 5 Mirroring Enable */ ++// {0x120C, 4, 1, 0x28}, /* XRX200_PCE_PCTRL_3_VIO_4 Violation Type 4 Mirroring Enable */ ++// {0x120C, 3, 1, 0x28}, /* XRX200_PCE_PCTRL_3_VIO_3 Violation Type 3 Mirroring Enable */ ++// {0x120C, 2, 1, 0x28}, /* XRX200_PCE_PCTRL_3_VIO_2 Violation Type 2 Mirroring Enable */ ++// {0x120C, 1, 1, 0x28}, /* XRX200_PCE_PCTRL_3_VIO_1 Violation Type 1 Mirroring Enable */ ++// {0x120C, 0, 1, 0x28}, /* XRX200_PCE_PCTRL_3_VIO_0 Violation Type 0 Mirroring Enable */ ++// {0x1210, 0, 16, 0x28}, /* XRX200_WOL_CTRL Wake-on-LAN ControlRegister */ ++// {0x1210, 0, 1, 0x28}, /* XRX200_WOL_CTRL_PORT WoL Enable */ ++// {0x1214, 0, 16, 0x28}, /* XRX200_PCE_VCTRL PCE VLAN ControlRegister */ ++ {0x1214, 5, 1, 0x28}, /* XRX200_PCE_VCTRL_VSR VLAN Security Rule */ ++ {0x1214, 4, 1, 0x28}, /* XRX200_PCE_VCTRL_VEMR VLAN Egress Member Violation Rule */ ++ {0x1214, 3, 1, 0x28}, /* XRX200_PCE_VCTRL_VIMR VLAN Ingress Member Violation Rule */ ++ {0x1214, 1, 2, 0x28}, /* XRX200_PCE_VCTRL_VINR VLAN Ingress Tag Rule */ ++ {0x1214, 0, 1, 0x28}, /* XRX200_PCE_VCTRL_UVR Unknown VLAN Rule */ ++// {0x1218, 0, 16, 0x28}, /* XRX200_PCE_DEFPVID PCE Default PortVID Register */ ++ {0x1218, 0, 6, 0x28}, /* XRX200_PCE_DEFPVID_PVID Default Port VID Index */ ++// {0x121C, 0, 16, 0x28}, /* XRX200_PCE_PSTAT PCE Port StatusRegister */ ++// {0x121C, 0, 16, 0x28}, /* XRX200_PCE_PSTAT_LRNCNT Learning Count */ ++// {0x1220, 0, 16, 0x28}, /* XRX200_PCE_PIER Parser and ClassificationEngine Port Interrupt Enable Register */ ++// {0x1220, 5, 1, 0x28}, /* XRX200_PCE_PIER_CLDRP Classification Drop Interrupt Enable */ ++// {0x1220, 4, 1, 0x28}, /* XRX200_PCE_PIER_PTDRP Port Drop Interrupt Enable */ ++// {0x1220, 3, 1, 0x28}, /* XRX200_PCE_PIER_VLAN VLAN Violation Interrupt Enable */ ++// {0x1220, 2, 1, 0x28}, /* XRX200_PCE_PIER_WOL Wake-on-LAN Interrupt Enable */ ++// {0x1220, 1, 1, 0x28}, /* XRX200_PCE_PIER_LOCK Port Limit Alert Interrupt Enable */ ++// {0x1220, 0, 1, 0x28}, /* XRX200_PCE_PIER_LIM Port Lock Alert Interrupt Enable */ ++// {0x1224, 0, 16, 0x28}, /* XRX200_PCE_PISR Parser and ClassificationEngine Port Interrupt Status Register */ ++// {0x1224, 5, 1, 0x28}, /* XRX200_PCE_PISR_CLDRP Classification Drop Interrupt */ ++// {0x1224, 4, 1, 0x28}, /* XRX200_PCE_PISR_PTDRP Port Drop Interrupt */ ++// {0x1224, 3, 1, 0x28}, /* XRX200_PCE_PISR_VLAN VLAN Violation Interrupt */ ++// {0x1224, 2, 1, 0x28}, /* XRX200_PCE_PISR_WOL Wake-on-LAN Interrupt */ ++// {0x1224, 1, 1, 0x28}, /* XRX200_PCE_PISR_LOCK Port Lock Alert Interrupt */ ++// {0x1224, 0, 1, 0x28}, /* XRX200_PCE_PISR_LIMIT Port Limitation Alert Interrupt */ ++// {0x1600, 0, 16, 0x1c}, /* XRX200_PCE_TCM_CTRL Three-colorMarker Control Register */ ++// {0x1600, 0, 1, 0x1c}, /* XRX200_PCE_TCM_CTRL_TCMEN Three-color Marker metering instance enable */ ++// {0x1604, 0, 16, 0x1c}, /* XRX200_PCE_TCM_STAT Three-colorMarker Status Register */ ++// {0x1604, 1, 1, 0x1c}, /* XRX200_PCE_TCM_STAT_AL1 Three-color Marker Alert 1 Status */ ++// {0x1604, 0, 1, 0x1c}, /* XRX200_PCE_TCM_STAT_AL0 Three-color Marker Alert 0 Status */ ++// {0x1608, 0, 16, 0x1c}, /* XRX200_PCE_TCM_CBS Three-color MarkerCommitted Burst Size Register */ ++// {0x1608, 0, 10, 0x1c}, /* XRX200_PCE_TCM_CBS_CBS Committed Burst Size */ ++// {0x160C, 0, 16, 0x1c}, /* XRX200_PCE_TCM_EBS Three-color MarkerExcess Burst Size Register */ ++// {0x160C, 0, 10, 0x1c}, /* XRX200_PCE_TCM_EBS_EBS Excess Burst Size */ ++// {0x1610, 0, 16, 0x1c}, /* XRX200_PCE_TCM_IBS Three-color MarkerInstantaneous Burst Size Register */ ++// {0x1610, 0, 2, 0x1c}, /* XRX200_PCE_TCM_IBS_IBS Instantaneous Burst Size */ ++// {0x1614, 0, 16, 0x1c}, /* XRX200_PCE_TCM_CIR_MANT Three-colorMarker Constant Information Rate Mantissa Register */ ++// {0x1614, 0, 10, 0x1c}, /* XRX200_PCE_TCM_CIR_MANT_MANT Rate Counter Mantissa */ ++// {0x1618, 0, 16, 0x1c}, /* XRX200_PCE_TCM_CIR_EXP Three-colorMarker Constant Information Rate Exponent Register */ ++// {0x1618, 0, 4, 0x1c}, /* XRX200_PCE_TCM_CIR_EXP_EXP Rate Counter Exponent */ ++// {0x2300, 0, 16, 0x00}, /* XRX200_MAC_TEST MAC Test Register */ ++// {0x2300, 0, 16, 0x00}, /* XRX200_MAC_TEST_JTP Jitter Test Pattern */ ++// {0x2304, 0, 16, 0x00}, /* XRX200_MAC_PFAD_CFG MAC Pause FrameSource Address Configuration Register */ ++// {0x2304, 0, 1, 0x00}, /* XRX200_MAC_PFAD_CFG_SAMOD Source Address Mode */ ++// {0x2308, 0, 16, 0x00}, /* XRX200_MAC_PFSA_0 Pause Frame SourceAddress Part 0 */ ++// {0x2308, 0, 16, 0x00}, /* XRX200_MAC_PFSA_0_PFAD Pause Frame Source Address Part 0 */ ++// {0x230C, 0, 16, 0x00}, /* XRX200_MAC_PFSA_1 Pause Frame SourceAddress Part 1 */ ++// {0x230C, 0, 16, 0x00}, /* XRX200_MAC_PFSA_1_PFAD Pause Frame Source Address Part 1 */ ++// {0x2310, 0, 16, 0x00}, /* XRX200_MAC_PFSA_2 Pause Frame SourceAddress Part 2 */ ++// {0x2310, 0, 16, 0x00}, /* XRX200_MAC_PFSA_2_PFAD Pause Frame Source Address Part 2 */ ++// {0x2314, 0, 16, 0x00}, /* XRX200_MAC_FLEN MAC Frame Length Register */ ++// {0x2314, 0, 14, 0x00}, /* XRX200_MAC_FLEN_LEN Maximum Frame Length */ ++// {0x2318, 0, 16, 0x00}, /* XRX200_MAC_VLAN_ETYPE_0 MAC VLAN EthertypeRegister 0 */ ++// {0x2318, 0, 16, 0x00}, /* XRX200_MAC_VLAN_ETYPE_0_OUTER Ethertype */ ++// {0x231C, 0, 16, 0x00}, /* XRX200_MAC_VLAN_ETYPE_1 MAC VLAN EthertypeRegister 1 */ ++// {0x231C, 0, 16, 0x00}, /* XRX200_MAC_VLAN_ETYPE_1_INNER Ethertype */ ++// {0x2320, 0, 16, 0x00}, /* XRX200_MAC_IER MAC Interrupt EnableRegister */ ++// {0x2320, 0, 8, 0x00}, /* XRX200_MAC_IER_MACIEN MAC Interrupt Enable */ ++// {0x2324, 0, 16, 0x00}, /* XRX200_MAC_ISR MAC Interrupt StatusRegister */ ++// {0x2324, 0, 8, 0x00}, /* XRX200_MAC_ISR_MACINT MAC Interrupt */ ++// {0x2400, 0, 16, 0x30}, /* XRX200_MAC_PSTAT MAC Port Status Register */ ++// {0x2400, 11, 1, 0x30}, /* XRX200_MAC_PSTAT_PACT PHY Active Status */ ++ {0x2400, 10, 1, 0x30}, /* XRX200_MAC_PSTAT_GBIT Gigabit Speed Status */ ++ {0x2400, 9, 1, 0x30}, /* XRX200_MAC_PSTAT_MBIT Megabit Speed Status */ ++ {0x2400, 8, 1, 0x30}, /* XRX200_MAC_PSTAT_FDUP Full Duplex Status */ ++// {0x2400, 7, 1, 0x30}, /* XRX200_MAC_PSTAT_RXPAU Receive Pause Status */ ++// {0x2400, 6, 1, 0x30}, /* XRX200_MAC_PSTAT_TXPAU Transmit Pause Status */ ++// {0x2400, 5, 1, 0x30}, /* XRX200_MAC_PSTAT_RXPAUEN Receive Pause Enable Status */ ++// {0x2400, 4, 1, 0x30}, /* XRX200_MAC_PSTAT_TXPAUEN Transmit Pause Enable Status */ ++ {0x2400, 3, 1, 0x30}, /* XRX200_MAC_PSTAT_LSTAT Link Status */ ++// {0x2400, 2, 1, 0x30}, /* XRX200_MAC_PSTAT_CRS Carrier Sense Status */ ++// {0x2400, 1, 1, 0x30}, /* XRX200_MAC_PSTAT_TXLPI Transmit Low-power Idle Status */ ++// {0x2400, 0, 1, 0x30}, /* XRX200_MAC_PSTAT_RXLPI Receive Low-power Idle Status */ ++// {0x2404, 0, 16, 0x30}, /* XRX200_MAC_PISR MAC Interrupt Status Register */ ++// {0x2404, 13, 1, 0x30}, /* XRX200_MAC_PISR_PACT PHY Active Status */ ++// {0x2404, 12, 1, 0x30}, /* XRX200_MAC_PISR_SPEED Megabit Speed Status */ ++// {0x2404, 11, 1, 0x30}, /* XRX200_MAC_PISR_FDUP Full Duplex Status */ ++// {0x2404, 10, 1, 0x30}, /* XRX200_MAC_PISR_RXPAUEN Receive Pause Enable Status */ ++// {0x2404, 9, 1, 0x30}, /* XRX200_MAC_PISR_TXPAUEN Transmit Pause Enable Status */ ++// {0x2404, 8, 1, 0x30}, /* XRX200_MAC_PISR_LPIOFF Receive Low-power Idle Mode is left */ ++// {0x2404, 7, 1, 0x30}, /* XRX200_MAC_PISR_LPION Receive Low-power Idle Mode is entered */ ++// {0x2404, 6, 1, 0x30}, /* XRX200_MAC_PISR_JAM Jam Status Detected */ ++// {0x2404, 5, 1, 0x30}, /* XRX200_MAC_PISR_TOOSHORT Too Short Frame Error Detected */ ++// {0x2404, 4, 1, 0x30}, /* XRX200_MAC_PISR_TOOLONG Too Long Frame Error Detected */ ++// {0x2404, 3, 1, 0x30}, /* XRX200_MAC_PISR_LENERR Length Mismatch Error Detected */ ++// {0x2404, 2, 1, 0x30}, /* XRX200_MAC_PISR_FCSERR Frame Checksum Error Detected */ ++// {0x2404, 1, 1, 0x30}, /* XRX200_MAC_PISR_TXPAUSE Pause Frame Transmitted */ ++// {0x2404, 0, 1, 0x30}, /* XRX200_MAC_PISR_RXPAUSE Pause Frame Received */ ++// {0x2408, 0, 16, 0x30}, /* XRX200_MAC_PIER MAC Interrupt Enable Register */ ++// {0x2408, 13, 1, 0x30}, /* XRX200_MAC_PIER_PACT PHY Active Status */ ++// {0x2408, 12, 1, 0x30}, /* XRX200_MAC_PIER_SPEED Megabit Speed Status */ ++// {0x2408, 11, 1, 0x30}, /* XRX200_MAC_PIER_FDUP Full Duplex Status */ ++// {0x2408, 10, 1, 0x30}, /* XRX200_MAC_PIER_RXPAUEN Receive Pause Enable Status */ ++// {0x2408, 9, 1, 0x30}, /* XRX200_MAC_PIER_TXPAUEN Transmit Pause Enable Status */ ++// {0x2408, 8, 1, 0x30}, /* XRX200_MAC_PIER_LPIOFF Low-power Idle Off Interrupt Mask */ ++// {0x2408, 7, 1, 0x30}, /* XRX200_MAC_PIER_LPION Low-power Idle On Interrupt Mask */ ++// {0x2408, 6, 1, 0x30}, /* XRX200_MAC_PIER_JAM Jam Status Interrupt Mask */ ++// {0x2408, 5, 1, 0x30}, /* XRX200_MAC_PIER_TOOSHORT Too Short Frame Error Interrupt Mask */ ++// {0x2408, 4, 1, 0x30}, /* XRX200_MAC_PIER_TOOLONG Too Long Frame Error Interrupt Mask */ ++// {0x2408, 3, 1, 0x30}, /* XRX200_MAC_PIER_LENERR Length Mismatch Error Interrupt Mask */ ++// {0x2408, 2, 1, 0x30}, /* XRX200_MAC_PIER_FCSERR Frame Checksum Error Interrupt Mask */ ++// {0x2408, 1, 1, 0x30}, /* XRX200_MAC_PIER_TXPAUSE Transmit Pause Frame Interrupt Mask */ ++// {0x2408, 0, 1, 0x30}, /* XRX200_MAC_PIER_RXPAUSE Receive Pause Frame Interrupt Mask */ ++// {0x240C, 0, 16, 0x30}, /* XRX200_MAC_CTRL_0 MAC Control Register0 */ ++// {0x240C, 13, 2, 0x30}, /* XRX200_MAC_CTRL_0_LCOL Late Collision Control */ ++// {0x240C, 12, 1, 0x30}, /* XRX200_MAC_CTRL_0_BM Burst Mode Control */ ++// {0x240C, 11, 1, 0x30}, /* XRX200_MAC_CTRL_0_APADEN Automatic VLAN Padding Enable */ ++// {0x240C, 10, 1, 0x30}, /* XRX200_MAC_CTRL_0_VPAD2EN Stacked VLAN Padding Enable */ ++// {0x240C, 9, 1, 0x30}, /* XRX200_MAC_CTRL_0_VPADEN VLAN Padding Enable */ ++// {0x240C, 8, 1, 0x30}, /* XRX200_MAC_CTRL_0_PADEN Padding Enable */ ++// {0x240C, 7, 1, 0x30}, /* XRX200_MAC_CTRL_0_FCS Transmit FCS Control */ ++ {0x240C, 4, 3, 0x30}, /* XRX200_MAC_CTRL_0_FCON Flow Control Mode */ ++// {0x240C, 2, 2, 0x30}, /* XRX200_MAC_CTRL_0_FDUP Full Duplex Control */ ++// {0x240C, 0, 2, 0x30}, /* XRX200_MAC_CTRL_0_GMII GMII/MII interface mode selection */ ++// {0x2410, 0, 16, 0x30}, /* XRX200_MAC_CTRL_1 MAC Control Register1 */ ++// {0x2410, 8, 1, 0x30}, /* XRX200_MAC_CTRL_1_SHORTPRE Short Preamble Control */ ++// {0x2410, 0, 4, 0x30}, /* XRX200_MAC_CTRL_1_IPG Minimum Inter Packet Gap Size */ ++// {0x2414, 0, 16, 0x30}, /* XRX200_MAC_CTRL_2 MAC Control Register2 */ ++// {0x2414, 3, 1, 0x30}, /* XRX200_MAC_CTRL_2_MLEN Maximum Untagged Frame Length */ ++// {0x2414, 2, 1, 0x30}, /* XRX200_MAC_CTRL_2_LCHKL Frame Length Check Long Enable */ ++// {0x2414, 0, 2, 0x30}, /* XRX200_MAC_CTRL_2_LCHKS Frame Length Check Short Enable */ ++// {0x2418, 0, 16, 0x30}, /* XRX200_MAC_CTRL_3 MAC Control Register3 */ ++// {0x2418, 0, 4, 0x30}, /* XRX200_MAC_CTRL_3_RCNT Retry Count */ ++// {0x241C, 0, 16, 0x30}, /* XRX200_MAC_CTRL_4 MAC Control Register4 */ ++// {0x241C, 7, 1, 0x30}, /* XRX200_MAC_CTRL_4_LPIEN LPI Mode Enable */ ++// {0x241C, 0, 7, 0x30}, /* XRX200_MAC_CTRL_4_WAIT LPI Wait Time */ ++// {0x2420, 0, 16, 0x30}, /* XRX200_MAC_CTRL_5_PJPS MAC Control Register5 */ ++// {0x2420, 1, 1, 0x30}, /* XRX200_MAC_CTRL_5_PJPS_NOBP Prolonged Jam pattern size during no-backpressure state */ ++// {0x2420, 0, 1, 0x30}, /* XRX200_MAC_CTRL_5_PJPS_BP Prolonged Jam pattern size during backpressure state */ ++// {0x2424, 0, 16, 0x30}, /* XRX200_MAC_CTRL_6_XBUF Transmit and ReceiveBuffer Control Register */ ++// {0x2424, 9, 3, 0x30}, /* XRX200_MAC_CTRL_6_RBUF_DLY_WP Delay */ ++// {0x2424, 8, 1, 0x30}, /* XRX200_MAC_CTRL_6_RBUF_INIT Receive Buffer Initialization */ ++// {0x2424, 6, 1, 0x30}, /* XRX200_MAC_CTRL_6_RBUF_BYPASS Bypass the Receive Buffer */ ++// {0x2424, 3, 3, 0x30}, /* XRX200_MAC_CTRL_6_XBUF_DLY_WP Delay */ ++// {0x2424, 2, 1, 0x30}, /* XRX200_MAC_CTRL_6_XBUF_INIT Initialize the Transmit Buffer */ ++// {0x2424, 0, 1, 0x30}, /* XRX200_MAC_CTRL_6_XBUF_BYPASS Bypass the Transmit Buffer */ ++// {0x2428, 0, 16, 0x30}, /* XRX200_MAC_BUFST_XBUF MAC Receive and TransmitBuffer Status Register */ ++// {0x2428, 3, 1, 0x30}, /* XRX200_MAC_BUFST_RBUF_UFL Receive Buffer Underflow Indicator */ ++// {0x2428, 2, 1, 0x30}, /* XRX200_MAC_BUFST_RBUF_OFL Receive Buffer Overflow Indicator */ ++// {0x2428, 1, 1, 0x30}, /* XRX200_MAC_BUFST_XBUF_UFL Transmit Buffer Underflow Indicator */ ++// {0x2428, 0, 1, 0x30}, /* XRX200_MAC_BUFST_XBUF_OFL Transmit Buffer Overflow Indicator */ ++// {0x242C, 0, 16, 0x30}, /* XRX200_MAC_TESTEN MAC Test Enable Register */ ++// {0x242C, 2, 1, 0x30}, /* XRX200_MAC_TESTEN_JTEN Jitter Test Enable */ ++// {0x242C, 1, 1, 0x30}, /* XRX200_MAC_TESTEN_TXER Transmit Error Insertion */ ++// {0x242C, 0, 1, 0x30}, /* XRX200_MAC_TESTEN_LOOP MAC Loopback Enable */ ++// {0x2900, 0, 16, 0x00}, /* XRX200_FDMA_CTRL Ethernet Switch FetchDMA Control Register */ ++// {0x2900, 7, 5, 0x00}, /* XRX200_FDMA_CTRL_LPI_THRESHOLD Low Power Idle Threshold */ ++// {0x2900, 4, 3, 0x00}, /* XRX200_FDMA_CTRL_LPI_MODE Low Power Idle Mode */ ++// {0x2900, 2, 2, 0x00}, /* XRX200_FDMA_CTRL_EGSTAG Egress Special Tag Size */ ++// {0x2900, 1, 1, 0x00}, /* XRX200_FDMA_CTRL_IGSTAG Ingress Special Tag Size */ ++// {0x2900, 0, 1, 0x00}, /* XRX200_FDMA_CTRL_EXCOL Excessive Collision Handling */ ++// {0x2904, 0, 16, 0x00}, /* XRX200_FDMA_STETYPE Special Tag EthertypeControl Register */ ++// {0x2904, 0, 16, 0x00}, /* XRX200_FDMA_STETYPE_ETYPE Special Tag Ethertype */ ++// {0x2908, 0, 16, 0x00}, /* XRX200_FDMA_VTETYPE VLAN Tag EthertypeControl Register */ ++// {0x2908, 0, 16, 0x00}, /* XRX200_FDMA_VTETYPE_ETYPE VLAN Tag Ethertype */ ++// {0x290C, 0, 16, 0x00}, /* XRX200_FDMA_STAT_0 FDMA Status Register0 */ ++// {0x290C, 0, 16, 0x00}, /* XRX200_FDMA_STAT_0_FSMS FSM states status */ ++// {0x2910, 0, 16, 0x00}, /* XRX200_FDMA_IER Fetch DMA Global InterruptEnable Register */ ++// {0x2910, 14, 1, 0x00}, /* XRX200_FDMA_IER_PCKD Packet Drop Interrupt Enable */ ++// {0x2910, 13, 1, 0x00}, /* XRX200_FDMA_IER_PCKR Packet Ready Interrupt Enable */ ++// {0x2910, 0, 8, 0x00}, /* XRX200_FDMA_IER_PCKT Packet Sent Interrupt Enable */ ++// {0x2914, 0, 16, 0x00}, /* XRX200_FDMA_ISR Fetch DMA Global InterruptStatus Register */ ++// {0x2914, 14, 1, 0x00}, /* XRX200_FDMA_ISR_PCKTD Packet Drop */ ++// {0x2914, 13, 1, 0x00}, /* XRX200_FDMA_ISR_PCKR Packet is Ready for Transmission */ ++// {0x2914, 0, 8, 0x00}, /* XRX200_FDMA_ISR_PCKT Packet Sent Event */ ++// {0x2A00, 0, 16, 0x18}, /* XRX200_FDMA_PCTRL Ethernet SwitchFetch DMA Port Control Register */ ++// {0x2A00, 3, 2, 0x18}, /* XRX200_FDMA_PCTRL_VLANMOD VLAN Modification Enable */ ++// {0x2A00, 2, 1, 0x18}, /* XRX200_FDMA_PCTRL_DSCPRM DSCP Re-marking Enable */ ++// {0x2A00, 1, 1, 0x18}, /* XRX200_FDMA_PCTRL_STEN Special Tag Insertion Enable */ ++// {0x2A00, 0, 1, 0x18}, /* XRX200_FDMA_PCTRL_EN FDMA Port Enable */ ++// {0x2A04, 0, 16, 0x18}, /* XRX200_FDMA_PRIO Ethernet SwitchFetch DMA Port Priority Register */ ++// {0x2A04, 0, 2, 0x18}, /* XRX200_FDMA_PRIO_PRIO FDMA PRIO */ ++// {0x2A08, 0, 16, 0x18}, /* XRX200_FDMA_PSTAT0 Ethernet SwitchFetch DMA Port Status Register 0 */ ++// {0x2A08, 15, 1, 0x18}, /* XRX200_FDMA_PSTAT0_PKT_AVAIL Port Egress Packet Available */ ++// {0x2A08, 14, 1, 0x18}, /* XRX200_FDMA_PSTAT0_POK Port Status OK */ ++// {0x2A08, 0, 6, 0x18}, /* XRX200_FDMA_PSTAT0_PSEG Port Egress Segment Count */ ++// {0x2A0C, 0, 16, 0x18}, /* XRX200_FDMA_PSTAT1_HDR Ethernet SwitchFetch DMA Port Status Register 1 */ ++// {0x2A0C, 0, 10, 0x18}, /* XRX200_FDMA_PSTAT1_HDR_PTR Header Pointer */ ++// {0x2A10, 0, 16, 0x18}, /* XRX200_FDMA_TSTAMP0 Egress TimeStamp Register 0 */ ++// {0x2A10, 0, 16, 0x18}, /* XRX200_FDMA_TSTAMP0_TSTL Time Stamp [15:0] */ ++// {0x2A14, 0, 16, 0x18}, /* XRX200_FDMA_TSTAMP1 Egress TimeStamp Register 1 */ ++// {0x2A14, 0, 16, 0x18}, /* XRX200_FDMA_TSTAMP1_TSTH Time Stamp [31:16] */ ++// {0x2D00, 0, 16, 0x00}, /* XRX200_SDMA_CTRL Ethernet Switch StoreDMA Control Register */ ++// {0x2D00, 0, 1, 0x00}, /* XRX200_SDMA_CTRL_TSTEN Time Stamp Enable */ ++// {0x2D04, 0, 16, 0x00}, /* XRX200_SDMA_FCTHR1 SDMA Flow Control Threshold1 Register */ ++// {0x2D04, 0, 10, 0x00}, /* XRX200_SDMA_FCTHR1_THR1 Threshold 1 */ ++// {0x2D08, 0, 16, 0x00}, /* XRX200_SDMA_FCTHR2 SDMA Flow Control Threshold2 Register */ ++// {0x2D08, 0, 10, 0x00}, /* XRX200_SDMA_FCTHR2_THR2 Threshold 2 */ ++// {0x2D0C, 0, 16, 0x00}, /* XRX200_SDMA_FCTHR3 SDMA Flow Control Threshold3 Register */ ++// {0x2D0C, 0, 10, 0x00}, /* XRX200_SDMA_FCTHR3_THR3 Threshold 3 */ ++// {0x2D10, 0, 16, 0x00}, /* XRX200_SDMA_FCTHR4 SDMA Flow Control Threshold4 Register */ ++// {0x2D10, 0, 10, 0x00}, /* XRX200_SDMA_FCTHR4_THR4 Threshold 4 */ ++// {0x2D14, 0, 16, 0x00}, /* XRX200_SDMA_FCTHR5 SDMA Flow Control Threshold5 Register */ ++// {0x2D14, 0, 10, 0x00}, /* XRX200_SDMA_FCTHR5_THR5 Threshold 5 */ ++// {0x2D18, 0, 16, 0x00}, /* XRX200_SDMA_FCTHR6 SDMA Flow Control Threshold6 Register */ ++// {0x2D18, 0, 10, 0x00}, /* XRX200_SDMA_FCTHR6_THR6 Threshold 6 */ ++// {0x2D1C, 0, 16, 0x00}, /* XRX200_SDMA_FCTHR7 SDMA Flow Control Threshold7 Register */ ++// {0x2D1C, 0, 11, 0x00}, /* XRX200_SDMA_FCTHR7_THR7 Threshold 7 */ ++// {0x2D20, 0, 16, 0x00}, /* XRX200_SDMA_STAT_0 SDMA Status Register0 */ ++// {0x2D20, 4, 3, 0x00}, /* XRX200_SDMA_STAT_0_BPS_FILL Back Pressure Status */ ++// {0x2D20, 2, 2, 0x00}, /* XRX200_SDMA_STAT_0_BPS_PNT Back Pressure Status */ ++// {0x2D20, 0, 2, 0x00}, /* XRX200_SDMA_STAT_0_DROP Back Pressure Status */ ++// {0x2D24, 0, 16, 0x00}, /* XRX200_SDMA_STAT_1 SDMA Status Register1 */ ++// {0x2D24, 0, 10, 0x00}, /* XRX200_SDMA_STAT_1_FILL Buffer Filling Level */ ++// {0x2D28, 0, 16, 0x00}, /* XRX200_SDMA_STAT_2 SDMA Status Register2 */ ++// {0x2D28, 0, 16, 0x00}, /* XRX200_SDMA_STAT_2_FSMS FSM states status */ ++// {0x2D2C, 0, 16, 0x00}, /* XRX200_SDMA_IER SDMA Interrupt Enable Register */ ++// {0x2D2C, 15, 1, 0x00}, /* XRX200_SDMA_IER_BPEX Buffer Pointers Exceeded */ ++// {0x2D2C, 14, 1, 0x00}, /* XRX200_SDMA_IER_BFULL Buffer Full */ ++// {0x2D2C, 13, 1, 0x00}, /* XRX200_SDMA_IER_FERR Frame Error */ ++// {0x2D2C, 0, 8, 0x00}, /* XRX200_SDMA_IER_FRX Frame Received Successfully */ ++// {0x2D30, 0, 16, 0x00}, /* XRX200_SDMA_ISR SDMA Interrupt Status Register */ ++// {0x2D30, 15, 1, 0x00}, /* XRX200_SDMA_ISR_BPEX Packet Descriptors Exceeded */ ++// {0x2D30, 14, 1, 0x00}, /* XRX200_SDMA_ISR_BFULL Buffer Full */ ++// {0x2D30, 13, 1, 0x00}, /* XRX200_SDMA_ISR_FERR Frame Error */ ++// {0x2D30, 0, 8, 0x00}, /* XRX200_SDMA_ISR_FRX Frame Received Successfully */ ++// {0x2F00, 0, 16, 0x18}, /* XRX200_SDMA_PCTRL Ethernet SwitchStore DMA Port Control Register */ ++// {0x2F00, 13, 2, 0x18}, /* XRX200_SDMA_PCTRL_DTHR Drop Threshold Selection */ ++// {0x2F00, 11, 2, 0x18}, /* XRX200_SDMA_PCTRL_PTHR Pause Threshold Selection */ ++// {0x2F00, 10, 1, 0x18}, /* XRX200_SDMA_PCTRL_PHYEFWD Forward PHY Error Frames */ ++// {0x2F00, 9, 1, 0x18}, /* XRX200_SDMA_PCTRL_ALGFWD Forward Alignment Error Frames */ ++// {0x2F00, 8, 1, 0x18}, /* XRX200_SDMA_PCTRL_LENFWD Forward Length Errored Frames */ ++// {0x2F00, 7, 1, 0x18}, /* XRX200_SDMA_PCTRL_OSFWD Forward Oversized Frames */ ++// {0x2F00, 6, 1, 0x18}, /* XRX200_SDMA_PCTRL_USFWD Forward Undersized Frames */ ++// {0x2F00, 5, 1, 0x18}, /* XRX200_SDMA_PCTRL_FCSIGN Ignore FCS Errors */ ++// {0x2F00, 4, 1, 0x18}, /* XRX200_SDMA_PCTRL_FCSFWD Forward FCS Errored Frames */ ++// {0x2F00, 3, 1, 0x18}, /* XRX200_SDMA_PCTRL_PAUFWD Pause Frame Forwarding */ ++// {0x2F00, 2, 1, 0x18}, /* XRX200_SDMA_PCTRL_MFCEN Metering Flow Control Enable */ ++// {0x2F00, 1, 1, 0x18}, /* XRX200_SDMA_PCTRL_FCEN Flow Control Enable */ ++// {0x2F00, 0, 1, 0x18}, /* XRX200_SDMA_PCTRL_PEN Port Enable */ ++// {0x2F04, 0, 16, 0x18}, /* XRX200_SDMA_PRIO Ethernet SwitchStore DMA Port Priority Register */ ++// {0x2F04, 0, 2, 0x18}, /* XRX200_SDMA_PRIO_PRIO SDMA PRIO */ ++// {0x2F08, 0, 16, 0x18}, /* XRX200_SDMA_PSTAT0_HDR Ethernet SwitchStore DMA Port Status Register 0 */ ++// {0x2F08, 0, 10, 0x18}, /* XRX200_SDMA_PSTAT0_HDR_PTR Port Ingress Queue Header Pointer */ ++// {0x2F0C, 0, 16, 0x18}, /* XRX200_SDMA_PSTAT1 Ethernet SwitchStore DMA Port Status Register 1 */ ++// {0x2F0C, 0, 10, 0x18}, /* XRX200_SDMA_PSTAT1_PPKT Port Ingress Packet Count */ ++// {0x2F10, 0, 16, 0x18}, /* XRX200_SDMA_TSTAMP0 Ingress TimeStamp Register 0 */ ++// {0x2F10, 0, 16, 0x18}, /* XRX200_SDMA_TSTAMP0_TSTL Time Stamp [15:0] */ ++// {0x2F14, 0, 16, 0x18}, /* XRX200_SDMA_TSTAMP1 Ingress TimeStamp Register 1 */ ++// {0x2F14, 0, 16, 0x18}, /* XRX200_SDMA_TSTAMP1_TSTH Time Stamp [31:16] */ ++}; ++ ++ diff --git a/target/linux/lantiq/patches-4.19/0027-01-net-phy-intel-xway-add-VR9-version-number.patch b/target/linux/lantiq/patches-4.19/0027-01-net-phy-intel-xway-add-VR9-version-number.patch new file mode 100644 index 0000000000..b02b3fbd2c --- /dev/null +++ b/target/linux/lantiq/patches-4.19/0027-01-net-phy-intel-xway-add-VR9-version-number.patch @@ -0,0 +1,62 @@ +From 5b73d9955fb4b0e3c37f8f6c71910293246c89dc Mon Sep 17 00:00:00 2001 +From: Mathias Kresin +Date: Thu, 22 Mar 2018 23:31:38 +0100 +Subject: [PATCH 1/2] net: phy: intel-xway: add VR9 version number + +The VR9 phy ids are matching only for the SoC version 1.2. Rename the +macros and change the names to take this into account. + +Signed-off-by: Mathias Kresin +Signed-off-by: David S. Miller +--- + drivers/net/phy/intel-xway.c | 16 ++++++++-------- + 1 file changed, 8 insertions(+), 8 deletions(-) + +--- a/drivers/net/phy/intel-xway.c ++++ b/drivers/net/phy/intel-xway.c +@@ -149,8 +149,8 @@ + #define PHY_ID_PHY22F_1_4 0xD565A410 + #define PHY_ID_PHY11G_1_5 0xD565A401 + #define PHY_ID_PHY22F_1_5 0xD565A411 +-#define PHY_ID_PHY11G_VR9 0xD565A409 +-#define PHY_ID_PHY22F_VR9 0xD565A419 ++#define PHY_ID_PHY11G_VR9_1_2 0xD565A409 ++#define PHY_ID_PHY22F_VR9_1_2 0xD565A419 + + #if IS_ENABLED(CONFIG_OF_MDIO) + static int vr9_gphy_of_reg_init(struct phy_device *phydev) +@@ -366,9 +366,9 @@ static struct phy_driver xway_gphy[] = { + .suspend = genphy_suspend, + .resume = genphy_resume, + }, { +- .phy_id = PHY_ID_PHY11G_VR9, ++ .phy_id = PHY_ID_PHY11G_VR9_1_2, + .phy_id_mask = 0xffffffff, +- .name = "Intel XWAY PHY11G (xRX integrated)", ++ .name = "Intel XWAY PHY11G (xRX v1.2 integrated)", + .features = PHY_GBIT_FEATURES, + .flags = PHY_HAS_INTERRUPT, + .config_init = xway_gphy_config_init, +@@ -380,9 +380,9 @@ static struct phy_driver xway_gphy[] = { + .suspend = genphy_suspend, + .resume = genphy_resume, + }, { +- .phy_id = PHY_ID_PHY22F_VR9, ++ .phy_id = PHY_ID_PHY22F_VR9_1_2, + .phy_id_mask = 0xffffffff, +- .name = "Intel XWAY PHY22F (xRX integrated)", ++ .name = "Intel XWAY PHY22F (xRX v1.2 integrated)", + .features = PHY_BASIC_FEATURES, + .flags = PHY_HAS_INTERRUPT, + .config_init = xway_gphy_config_init, +@@ -404,8 +404,8 @@ static struct mdio_device_id __maybe_unu + { PHY_ID_PHY22F_1_4, 0xffffffff }, + { PHY_ID_PHY11G_1_5, 0xffffffff }, + { PHY_ID_PHY22F_1_5, 0xffffffff }, +- { PHY_ID_PHY11G_VR9, 0xffffffff }, +- { PHY_ID_PHY22F_VR9, 0xffffffff }, ++ { PHY_ID_PHY11G_VR9_1_2, 0xffffffff }, ++ { PHY_ID_PHY22F_VR9_1_2, 0xffffffff }, + { } + }; + MODULE_DEVICE_TABLE(mdio, xway_gphy_tbl); diff --git a/target/linux/lantiq/patches-4.19/0027-02-net-phy-intel-xway-add-VR9-v1.1-phy-ids.patch b/target/linux/lantiq/patches-4.19/0027-02-net-phy-intel-xway-add-VR9-v1.1-phy-ids.patch new file mode 100644 index 0000000000..c9229b3ae2 --- /dev/null +++ b/target/linux/lantiq/patches-4.19/0027-02-net-phy-intel-xway-add-VR9-v1.1-phy-ids.patch @@ -0,0 +1,69 @@ +From f452518c982e57538e6d49da0a2c80eef22087ab Mon Sep 17 00:00:00 2001 +From: Mathias Kresin +Date: Thu, 22 Mar 2018 23:31:39 +0100 +Subject: [PATCH 2/2] net: phy: intel-xway: add VR9 v1.1 phy ids + +The phys embedded into the v1.1 of the VR9 SoC are using different phy +ids. Add the phy ids to use the driver for this VR9 version as well. + +Signed-off-by: Mathias Kresin +Signed-off-by: David S. Miller +--- + drivers/net/phy/intel-xway.c | 28 ++++++++++++++++++++++++++++ + 1 file changed, 28 insertions(+) + +--- a/drivers/net/phy/intel-xway.c ++++ b/drivers/net/phy/intel-xway.c +@@ -149,6 +149,8 @@ + #define PHY_ID_PHY22F_1_4 0xD565A410 + #define PHY_ID_PHY11G_1_5 0xD565A401 + #define PHY_ID_PHY22F_1_5 0xD565A411 ++#define PHY_ID_PHY11G_VR9_1_1 0xD565A408 ++#define PHY_ID_PHY22F_VR9_1_1 0xD565A418 + #define PHY_ID_PHY11G_VR9_1_2 0xD565A409 + #define PHY_ID_PHY22F_VR9_1_2 0xD565A419 + +@@ -366,6 +368,34 @@ static struct phy_driver xway_gphy[] = { + .suspend = genphy_suspend, + .resume = genphy_resume, + }, { ++ .phy_id = PHY_ID_PHY11G_VR9_1_1, ++ .phy_id_mask = 0xffffffff, ++ .name = "Intel XWAY PHY11G (xRX v1.1 integrated)", ++ .features = PHY_GBIT_FEATURES, ++ .flags = PHY_HAS_INTERRUPT, ++ .config_init = xway_gphy_config_init, ++ .config_aneg = genphy_config_aneg, ++ .read_status = genphy_read_status, ++ .ack_interrupt = xway_gphy_ack_interrupt, ++ .did_interrupt = xway_gphy_did_interrupt, ++ .config_intr = xway_gphy_config_intr, ++ .suspend = genphy_suspend, ++ .resume = genphy_resume, ++ }, { ++ .phy_id = PHY_ID_PHY22F_VR9_1_1, ++ .phy_id_mask = 0xffffffff, ++ .name = "Intel XWAY PHY22F (xRX v1.1 integrated)", ++ .features = PHY_BASIC_FEATURES, ++ .flags = PHY_HAS_INTERRUPT, ++ .config_init = xway_gphy_config_init, ++ .config_aneg = genphy_config_aneg, ++ .read_status = genphy_read_status, ++ .ack_interrupt = xway_gphy_ack_interrupt, ++ .did_interrupt = xway_gphy_did_interrupt, ++ .config_intr = xway_gphy_config_intr, ++ .suspend = genphy_suspend, ++ .resume = genphy_resume, ++ }, { + .phy_id = PHY_ID_PHY11G_VR9_1_2, + .phy_id_mask = 0xffffffff, + .name = "Intel XWAY PHY11G (xRX v1.2 integrated)", +@@ -404,6 +434,8 @@ static struct mdio_device_id __maybe_unu + { PHY_ID_PHY22F_1_4, 0xffffffff }, + { PHY_ID_PHY11G_1_5, 0xffffffff }, + { PHY_ID_PHY22F_1_5, 0xffffffff }, ++ { PHY_ID_PHY11G_VR9_1_1, 0xffffffff }, ++ { PHY_ID_PHY22F_VR9_1_1, 0xffffffff }, + { PHY_ID_PHY11G_VR9_1_2, 0xffffffff }, + { PHY_ID_PHY22F_VR9_1_2, 0xffffffff }, + { } diff --git a/target/linux/lantiq/patches-4.19/0028-NET-lantiq-various-etop-fixes.patch b/target/linux/lantiq/patches-4.19/0028-NET-lantiq-various-etop-fixes.patch new file mode 100644 index 0000000000..83aef78ca0 --- /dev/null +++ b/target/linux/lantiq/patches-4.19/0028-NET-lantiq-various-etop-fixes.patch @@ -0,0 +1,868 @@ +From 870ed9cae083ff8a60a739ef7e74c5a1800533be Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Tue, 9 Sep 2014 22:45:34 +0200 +Subject: [PATCH 28/36] NET: lantiq: various etop fixes + +Signed-off-by: John Crispin +--- + drivers/net/ethernet/lantiq_etop.c | 555 +++++++++++++++++++++++++----------- + 1 file changed, 389 insertions(+), 166 deletions(-) + +--- a/drivers/net/ethernet/lantiq_etop.c ++++ b/drivers/net/ethernet/lantiq_etop.c +@@ -11,7 +11,7 @@ + * You should have received a copy of the GNU General Public License + * along with this program; if not, see . + * +- * Copyright (C) 2011 John Crispin ++ * Copyright (C) 2011-12 John Crispin + */ + + #include +@@ -30,11 +30,16 @@ + #include + #include + #include ++#include + #include + #include + #include + #include + #include ++#include ++#include ++#include ++#include + + #include + +@@ -42,7 +47,7 @@ + #include + #include + +-#define LTQ_ETOP_MDIO 0x11804 ++#define LTQ_ETOP_MDIO_ACC 0x11804 + #define MDIO_REQUEST 0x80000000 + #define MDIO_READ 0x40000000 + #define MDIO_ADDR_MASK 0x1f +@@ -51,44 +56,91 @@ + #define MDIO_REG_OFFSET 0x10 + #define MDIO_VAL_MASK 0xffff + +-#define PPE32_CGEN 0x800 +-#define LQ_PPE32_ENET_MAC_CFG 0x1840 ++#define LTQ_ETOP_MDIO_CFG 0x11800 ++#define MDIO_CFG_MASK 0x6 ++ ++#define LTQ_ETOP_CFG 0x11808 ++#define LTQ_ETOP_IGPLEN 0x11820 ++#define LTQ_ETOP_MAC_CFG 0x11840 + + #define LTQ_ETOP_ENETS0 0x11850 + #define LTQ_ETOP_MAC_DA0 0x1186C + #define LTQ_ETOP_MAC_DA1 0x11870 +-#define LTQ_ETOP_CFG 0x16020 +-#define LTQ_ETOP_IGPLEN 0x16080 ++ ++#define MAC_CFG_MASK 0xfff ++#define MAC_CFG_CGEN (1 << 11) ++#define MAC_CFG_DUPLEX (1 << 2) ++#define MAC_CFG_SPEED (1 << 1) ++#define MAC_CFG_LINK (1 << 0) + + #define MAX_DMA_CHAN 0x8 + #define MAX_DMA_CRC_LEN 0x4 + #define MAX_DMA_DATA_LEN 0x600 + + #define ETOP_FTCU BIT(28) +-#define ETOP_MII_MASK 0xf +-#define ETOP_MII_NORMAL 0xd +-#define ETOP_MII_REVERSE 0xe + #define ETOP_PLEN_UNDER 0x40 +-#define ETOP_CGEN 0x800 ++#define ETOP_CFG_MII0 0x01 + +-/* use 2 static channels for TX/RX */ +-#define LTQ_ETOP_TX_CHANNEL 1 +-#define LTQ_ETOP_RX_CHANNEL 6 +-#define IS_TX(x) (x == LTQ_ETOP_TX_CHANNEL) +-#define IS_RX(x) (x == LTQ_ETOP_RX_CHANNEL) ++#define ETOP_CFG_MASK 0xfff ++#define ETOP_CFG_FEN0 (1 << 8) ++#define ETOP_CFG_SEN0 (1 << 6) ++#define ETOP_CFG_OFF1 (1 << 3) ++#define ETOP_CFG_REMII0 (1 << 1) ++#define ETOP_CFG_OFF0 (1 << 0) ++ ++#define LTQ_GBIT_MDIO_CTL 0xCC ++#define LTQ_GBIT_MDIO_DATA 0xd0 ++#define LTQ_GBIT_GCTL0 0x68 ++#define LTQ_GBIT_PMAC_HD_CTL 0x8c ++#define LTQ_GBIT_P0_CTL 0x4 ++#define LTQ_GBIT_PMAC_RX_IPG 0xa8 ++#define LTQ_GBIT_RGMII_CTL 0x78 ++ ++#define PMAC_HD_CTL_AS (1 << 19) ++#define PMAC_HD_CTL_RXSH (1 << 22) ++ ++/* Switch Enable (0=disable, 1=enable) */ ++#define GCTL0_SE 0x80000000 ++/* Disable MDIO auto polling (0=disable, 1=enable) */ ++#define PX_CTL_DMDIO 0x00400000 ++ ++/* MDC clock divider, clock = 25MHz/((MDC_CLOCK + 1) * 2) */ ++#define MDC_CLOCK_MASK 0xff000000 ++#define MDC_CLOCK_OFFSET 24 ++ ++/* register information for the gbit's MDIO bus */ ++#define MDIO_XR9_REQUEST 0x00008000 ++#define MDIO_XR9_READ 0x00000800 ++#define MDIO_XR9_WRITE 0x00000400 ++#define MDIO_XR9_REG_MASK 0x1f ++#define MDIO_XR9_ADDR_MASK 0x1f ++#define MDIO_XR9_RD_MASK 0xffff ++#define MDIO_XR9_REG_OFFSET 0 ++#define MDIO_XR9_ADDR_OFFSET 5 ++#define MDIO_XR9_WR_OFFSET 16 + ++#define LTQ_DMA_ETOP ((of_machine_is_compatible("lantiq,ase")) ? \ ++ (INT_NUM_IM3_IRL0) : (INT_NUM_IM2_IRL0)) ++ ++/* the newer xway socks have a embedded 3/7 port gbit multiplexer */ + #define ltq_etop_r32(x) ltq_r32(ltq_etop_membase + (x)) + #define ltq_etop_w32(x, y) ltq_w32(x, ltq_etop_membase + (y)) + #define ltq_etop_w32_mask(x, y, z) \ + ltq_w32_mask(x, y, ltq_etop_membase + (z)) + +-#define DRV_VERSION "1.0" ++#define ltq_gbit_r32(x) ltq_r32(ltq_gbit_membase + (x)) ++#define ltq_gbit_w32(x, y) ltq_w32(x, ltq_gbit_membase + (y)) ++#define ltq_gbit_w32_mask(x, y, z) \ ++ ltq_w32_mask(x, y, ltq_gbit_membase + (z)) ++ ++#define DRV_VERSION "1.2" + + static void __iomem *ltq_etop_membase; ++static void __iomem *ltq_gbit_membase; + + struct ltq_etop_chan { +- int idx; + int tx_free; ++ int irq; + struct net_device *netdev; + struct napi_struct napi; + struct ltq_dma_channel dma; +@@ -98,21 +150,34 @@ struct ltq_etop_chan { + struct ltq_etop_priv { + struct net_device *netdev; + struct platform_device *pdev; +- struct ltq_eth_data *pldata; + struct resource *res; + + struct mii_bus *mii_bus; + +- struct ltq_etop_chan ch[MAX_DMA_CHAN]; +- int tx_free[MAX_DMA_CHAN >> 1]; ++ struct ltq_etop_chan txch; ++ struct ltq_etop_chan rxch; ++ ++ int tx_irq; ++ int rx_irq; ++ ++ unsigned char mac[6]; ++ int mii_mode; + + spinlock_t lock; ++ ++ struct clk *clk_ppe; ++ struct clk *clk_switch; ++ struct clk *clk_ephy; ++ struct clk *clk_ephycgu; + }; + ++static int ltq_etop_mdio_wr(struct mii_bus *bus, int phy_addr, ++ int phy_reg, u16 phy_data); ++ + static int + ltq_etop_alloc_skb(struct ltq_etop_chan *ch) + { +- ch->skb[ch->dma.desc] = netdev_alloc_skb(ch->netdev, MAX_DMA_DATA_LEN); ++ ch->skb[ch->dma.desc] = dev_alloc_skb(MAX_DMA_DATA_LEN); + if (!ch->skb[ch->dma.desc]) + return -ENOMEM; + ch->dma.desc_base[ch->dma.desc].addr = dma_map_single(NULL, +@@ -147,8 +212,11 @@ ltq_etop_hw_receive(struct ltq_etop_chan + spin_unlock_irqrestore(&priv->lock, flags); + + skb_put(skb, len); ++ skb->dev = ch->netdev; + skb->protocol = eth_type_trans(skb, ch->netdev); + netif_receive_skb(skb); ++ ch->netdev->stats.rx_packets++; ++ ch->netdev->stats.rx_bytes += len; + } + + static int +@@ -156,7 +224,9 @@ ltq_etop_poll_rx(struct napi_struct *nap + { + struct ltq_etop_chan *ch = container_of(napi, + struct ltq_etop_chan, napi); ++ struct ltq_etop_priv *priv = netdev_priv(ch->netdev); + int work_done = 0; ++ unsigned long flags; + + while (work_done < budget) { + struct ltq_dma_desc *desc = &ch->dma.desc_base[ch->dma.desc]; +@@ -168,7 +238,9 @@ ltq_etop_poll_rx(struct napi_struct *nap + } + if (work_done < budget) { + napi_complete_done(&ch->napi, work_done); ++ spin_lock_irqsave(&priv->lock, flags); + ltq_dma_ack_irq(&ch->dma); ++ spin_unlock_irqrestore(&priv->lock, flags); + } + return work_done; + } +@@ -180,12 +252,14 @@ ltq_etop_poll_tx(struct napi_struct *nap + container_of(napi, struct ltq_etop_chan, napi); + struct ltq_etop_priv *priv = netdev_priv(ch->netdev); + struct netdev_queue *txq = +- netdev_get_tx_queue(ch->netdev, ch->idx >> 1); ++ netdev_get_tx_queue(ch->netdev, ch->dma.nr >> 1); + unsigned long flags; + + spin_lock_irqsave(&priv->lock, flags); + while ((ch->dma.desc_base[ch->tx_free].ctl & + (LTQ_DMA_OWN | LTQ_DMA_C)) == LTQ_DMA_C) { ++ ch->netdev->stats.tx_packets++; ++ ch->netdev->stats.tx_bytes += ch->skb[ch->tx_free]->len; + dev_kfree_skb_any(ch->skb[ch->tx_free]); + ch->skb[ch->tx_free] = NULL; + memset(&ch->dma.desc_base[ch->tx_free], 0, +@@ -198,7 +272,9 @@ ltq_etop_poll_tx(struct napi_struct *nap + if (netif_tx_queue_stopped(txq)) + netif_tx_start_queue(txq); + napi_complete(&ch->napi); ++ spin_lock_irqsave(&priv->lock, flags); + ltq_dma_ack_irq(&ch->dma); ++ spin_unlock_irqrestore(&priv->lock, flags); + return 1; + } + +@@ -206,9 +282,10 @@ static irqreturn_t + ltq_etop_dma_irq(int irq, void *_priv) + { + struct ltq_etop_priv *priv = _priv; +- int ch = irq - LTQ_DMA_CH0_INT; +- +- napi_schedule(&priv->ch[ch].napi); ++ if (irq == priv->txch.dma.irq) ++ napi_schedule(&priv->txch.napi); ++ else ++ napi_schedule(&priv->rxch.napi); + return IRQ_HANDLED; + } + +@@ -220,7 +297,7 @@ ltq_etop_free_channel(struct net_device + ltq_dma_free(&ch->dma); + if (ch->dma.irq) + free_irq(ch->dma.irq, priv); +- if (IS_RX(ch->idx)) { ++ if (ch == &priv->txch) { + int desc; + for (desc = 0; desc < LTQ_DESC_NUM; desc++) + dev_kfree_skb_any(ch->skb[ch->dma.desc]); +@@ -231,65 +308,133 @@ static void + ltq_etop_hw_exit(struct net_device *dev) + { + struct ltq_etop_priv *priv = netdev_priv(dev); +- int i; + +- ltq_pmu_disable(PMU_PPE); +- for (i = 0; i < MAX_DMA_CHAN; i++) +- if (IS_TX(i) || IS_RX(i)) +- ltq_etop_free_channel(dev, &priv->ch[i]); ++ clk_disable(priv->clk_ppe); ++ ++ if (of_machine_is_compatible("lantiq,ar9")) ++ clk_disable(priv->clk_switch); ++ ++ if (of_machine_is_compatible("lantiq,ase")) { ++ clk_disable(priv->clk_ephy); ++ clk_disable(priv->clk_ephycgu); ++ } ++ ++ ltq_etop_free_channel(dev, &priv->txch); ++ ltq_etop_free_channel(dev, &priv->rxch); ++} ++ ++static void ++ltq_etop_gbit_init(struct net_device *dev) ++{ ++ struct ltq_etop_priv *priv = netdev_priv(dev); ++ ++ clk_enable(priv->clk_switch); ++ ++ /* enable gbit port0 on the SoC */ ++ ltq_gbit_w32_mask((1 << 17), (1 << 18), LTQ_GBIT_P0_CTL); ++ ++ ltq_gbit_w32_mask(0, GCTL0_SE, LTQ_GBIT_GCTL0); ++ /* disable MDIO auto polling mode */ ++ ltq_gbit_w32_mask(0, PX_CTL_DMDIO, LTQ_GBIT_P0_CTL); ++ /* set 1522 packet size */ ++ ltq_gbit_w32_mask(0x300, 0, LTQ_GBIT_GCTL0); ++ /* disable pmac & dmac headers */ ++ ltq_gbit_w32_mask(PMAC_HD_CTL_AS | PMAC_HD_CTL_RXSH, 0, ++ LTQ_GBIT_PMAC_HD_CTL); ++ /* Due to traffic halt when burst length 8, ++ replace default IPG value with 0x3B */ ++ ltq_gbit_w32(0x3B, LTQ_GBIT_PMAC_RX_IPG); ++ /* set mdc clock to 2.5 MHz */ ++ ltq_gbit_w32_mask(MDC_CLOCK_MASK, 4 << MDC_CLOCK_OFFSET, ++ LTQ_GBIT_RGMII_CTL); + } + + static int + ltq_etop_hw_init(struct net_device *dev) + { + struct ltq_etop_priv *priv = netdev_priv(dev); +- int i; ++ int mii_mode = priv->mii_mode; + +- ltq_pmu_enable(PMU_PPE); ++ clk_enable(priv->clk_ppe); + +- switch (priv->pldata->mii_mode) { ++ if (of_machine_is_compatible("lantiq,ar9")) { ++ ltq_etop_gbit_init(dev); ++ /* force the etops link to the gbit to MII */ ++ mii_mode = PHY_INTERFACE_MODE_MII; ++ } ++ ltq_etop_w32_mask(MDIO_CFG_MASK, 0, LTQ_ETOP_MDIO_CFG); ++ ltq_etop_w32_mask(MAC_CFG_MASK, MAC_CFG_CGEN | MAC_CFG_DUPLEX | ++ MAC_CFG_SPEED | MAC_CFG_LINK, LTQ_ETOP_MAC_CFG); ++ ++ switch (mii_mode) { + case PHY_INTERFACE_MODE_RMII: +- ltq_etop_w32_mask(ETOP_MII_MASK, +- ETOP_MII_REVERSE, LTQ_ETOP_CFG); ++ ltq_etop_w32_mask(ETOP_CFG_MASK, ETOP_CFG_REMII0 | ETOP_CFG_OFF1 | ++ ETOP_CFG_SEN0 | ETOP_CFG_FEN0, LTQ_ETOP_CFG); + break; + + case PHY_INTERFACE_MODE_MII: +- ltq_etop_w32_mask(ETOP_MII_MASK, +- ETOP_MII_NORMAL, LTQ_ETOP_CFG); ++ ltq_etop_w32_mask(ETOP_CFG_MASK, ETOP_CFG_OFF1 | ++ ETOP_CFG_SEN0 | ETOP_CFG_FEN0, LTQ_ETOP_CFG); + break; + + default: ++ if (of_machine_is_compatible("lantiq,ase")) { ++ clk_enable(priv->clk_ephy); ++ /* disable external MII */ ++ ltq_etop_w32_mask(0, ETOP_CFG_MII0, LTQ_ETOP_CFG); ++ /* enable clock for internal PHY */ ++ clk_enable(priv->clk_ephycgu); ++ /* we need to write this magic to the internal phy to ++ make it work */ ++ ltq_etop_mdio_wr(NULL, 0x8, 0x12, 0xC020); ++ pr_info("Selected EPHY mode\n"); ++ break; ++ } + netdev_err(dev, "unknown mii mode %d\n", +- priv->pldata->mii_mode); ++ mii_mode); + return -ENOTSUPP; + } + +- /* enable crc generation */ +- ltq_etop_w32(PPE32_CGEN, LQ_PPE32_ENET_MAC_CFG); ++ return 0; ++} ++ ++static int ++ltq_etop_dma_init(struct net_device *dev) ++{ ++ struct ltq_etop_priv *priv = netdev_priv(dev); ++ int tx = priv->tx_irq - LTQ_DMA_ETOP; ++ int rx = priv->rx_irq - LTQ_DMA_ETOP; ++ int err; + + ltq_dma_init_port(DMA_PORT_ETOP); + +- for (i = 0; i < MAX_DMA_CHAN; i++) { +- int irq = LTQ_DMA_CH0_INT + i; +- struct ltq_etop_chan *ch = &priv->ch[i]; +- +- ch->idx = ch->dma.nr = i; +- +- if (IS_TX(i)) { +- ltq_dma_alloc_tx(&ch->dma); +- request_irq(irq, ltq_etop_dma_irq, 0, "etop_tx", priv); +- } else if (IS_RX(i)) { +- ltq_dma_alloc_rx(&ch->dma); +- for (ch->dma.desc = 0; ch->dma.desc < LTQ_DESC_NUM; +- ch->dma.desc++) +- if (ltq_etop_alloc_skb(ch)) +- return -ENOMEM; +- ch->dma.desc = 0; +- request_irq(irq, ltq_etop_dma_irq, 0, "etop_rx", priv); ++ priv->txch.dma.nr = tx; ++ ltq_dma_alloc_tx(&priv->txch.dma); ++ err = request_irq(priv->tx_irq, ltq_etop_dma_irq, 0, "eth_tx", priv); ++ if (err) { ++ netdev_err(dev, "failed to allocate tx irq\n"); ++ goto err_out; ++ } ++ priv->txch.dma.irq = priv->tx_irq; ++ ++ priv->rxch.dma.nr = rx; ++ ltq_dma_alloc_rx(&priv->rxch.dma); ++ for (priv->rxch.dma.desc = 0; priv->rxch.dma.desc < LTQ_DESC_NUM; ++ priv->rxch.dma.desc++) { ++ if (ltq_etop_alloc_skb(&priv->rxch)) { ++ netdev_err(dev, "failed to allocate skbs\n"); ++ err = -ENOMEM; ++ goto err_out; + } +- ch->dma.irq = irq; + } +- return 0; ++ priv->rxch.dma.desc = 0; ++ err = request_irq(priv->rx_irq, ltq_etop_dma_irq, 0, "eth_rx", priv); ++ if (err) ++ netdev_err(dev, "failed to allocate rx irq\n"); ++ else ++ priv->rxch.dma.irq = priv->rx_irq; ++err_out: ++ return err; + } + + static void +@@ -308,6 +453,39 @@ static const struct ethtool_ops ltq_etop + }; + + static int ++ltq_etop_mdio_wr_xr9(struct mii_bus *bus, int phy_addr, ++ int phy_reg, u16 phy_data) ++{ ++ u32 val = MDIO_XR9_REQUEST | MDIO_XR9_WRITE | ++ (phy_data << MDIO_XR9_WR_OFFSET) | ++ ((phy_addr & MDIO_XR9_ADDR_MASK) << MDIO_XR9_ADDR_OFFSET) | ++ ((phy_reg & MDIO_XR9_REG_MASK) << MDIO_XR9_REG_OFFSET); ++ ++ while (ltq_gbit_r32(LTQ_GBIT_MDIO_CTL) & MDIO_XR9_REQUEST) ++ ; ++ ltq_gbit_w32(val, LTQ_GBIT_MDIO_CTL); ++ while (ltq_gbit_r32(LTQ_GBIT_MDIO_CTL) & MDIO_XR9_REQUEST) ++ ; ++ return 0; ++} ++ ++static int ++ltq_etop_mdio_rd_xr9(struct mii_bus *bus, int phy_addr, int phy_reg) ++{ ++ u32 val = MDIO_XR9_REQUEST | MDIO_XR9_READ | ++ ((phy_addr & MDIO_XR9_ADDR_MASK) << MDIO_XR9_ADDR_OFFSET) | ++ ((phy_reg & MDIO_XR9_REG_MASK) << MDIO_XR9_REG_OFFSET); ++ ++ while (ltq_gbit_r32(LTQ_GBIT_MDIO_CTL) & MDIO_XR9_REQUEST) ++ ; ++ ltq_gbit_w32(val, LTQ_GBIT_MDIO_CTL); ++ while (ltq_gbit_r32(LTQ_GBIT_MDIO_CTL) & MDIO_XR9_REQUEST) ++ ; ++ val = ltq_gbit_r32(LTQ_GBIT_MDIO_DATA) & MDIO_XR9_RD_MASK; ++ return val; ++} ++ ++static int + ltq_etop_mdio_wr(struct mii_bus *bus, int phy_addr, int phy_reg, u16 phy_data) + { + u32 val = MDIO_REQUEST | +@@ -315,9 +493,9 @@ ltq_etop_mdio_wr(struct mii_bus *bus, in + ((phy_reg & MDIO_REG_MASK) << MDIO_REG_OFFSET) | + phy_data; + +- while (ltq_etop_r32(LTQ_ETOP_MDIO) & MDIO_REQUEST) ++ while (ltq_etop_r32(LTQ_ETOP_MDIO_ACC) & MDIO_REQUEST) + ; +- ltq_etop_w32(val, LTQ_ETOP_MDIO); ++ ltq_etop_w32(val, LTQ_ETOP_MDIO_ACC); + return 0; + } + +@@ -328,12 +506,12 @@ ltq_etop_mdio_rd(struct mii_bus *bus, in + ((phy_addr & MDIO_ADDR_MASK) << MDIO_ADDR_OFFSET) | + ((phy_reg & MDIO_REG_MASK) << MDIO_REG_OFFSET); + +- while (ltq_etop_r32(LTQ_ETOP_MDIO) & MDIO_REQUEST) ++ while (ltq_etop_r32(LTQ_ETOP_MDIO_ACC) & MDIO_REQUEST) + ; +- ltq_etop_w32(val, LTQ_ETOP_MDIO); +- while (ltq_etop_r32(LTQ_ETOP_MDIO) & MDIO_REQUEST) ++ ltq_etop_w32(val, LTQ_ETOP_MDIO_ACC); ++ while (ltq_etop_r32(LTQ_ETOP_MDIO_ACC) & MDIO_REQUEST) + ; +- val = ltq_etop_r32(LTQ_ETOP_MDIO) & MDIO_VAL_MASK; ++ val = ltq_etop_r32(LTQ_ETOP_MDIO_ACC) & MDIO_VAL_MASK; + return val; + } + +@@ -348,8 +526,18 @@ ltq_etop_mdio_probe(struct net_device *d + { + struct ltq_etop_priv *priv = netdev_priv(dev); + struct phy_device *phydev; ++ u32 phy_supported = (SUPPORTED_10baseT_Half ++ | SUPPORTED_10baseT_Full ++ | SUPPORTED_100baseT_Half ++ | SUPPORTED_100baseT_Full ++ | SUPPORTED_Autoneg ++ | SUPPORTED_MII ++ | SUPPORTED_TP); + +- phydev = phy_find_first(priv->mii_bus); ++ if (of_machine_is_compatible("lantiq,ase")) ++ phydev = mdiobus_get_phy(priv->mii_bus, 8); ++ else ++ phydev = mdiobus_get_phy(priv->mii_bus, 0); + + if (!phydev) { + netdev_err(dev, "no PHY found\n"); +@@ -357,21 +545,18 @@ ltq_etop_mdio_probe(struct net_device *d + } + + phydev = phy_connect(dev, phydev_name(phydev), +- <q_etop_mdio_link, priv->pldata->mii_mode); ++ <q_etop_mdio_link, priv->mii_mode); + + if (IS_ERR(phydev)) { + netdev_err(dev, "Could not attach to PHY\n"); + return PTR_ERR(phydev); + } + +- phydev->supported &= (SUPPORTED_10baseT_Half +- | SUPPORTED_10baseT_Full +- | SUPPORTED_100baseT_Half +- | SUPPORTED_100baseT_Full +- | SUPPORTED_Autoneg +- | SUPPORTED_MII +- | SUPPORTED_TP); ++ if (of_machine_is_compatible("lantiq,ar9")) ++ phy_supported |= SUPPORTED_1000baseT_Half ++ | SUPPORTED_1000baseT_Full; + ++ phydev->supported &= phy_supported; + phydev->advertising = phydev->supported; + phy_attached_info(phydev); + +@@ -392,8 +577,13 @@ ltq_etop_mdio_init(struct net_device *de + } + + priv->mii_bus->priv = dev; +- priv->mii_bus->read = ltq_etop_mdio_rd; +- priv->mii_bus->write = ltq_etop_mdio_wr; ++ if (of_machine_is_compatible("lantiq,ar9")) { ++ priv->mii_bus->read = ltq_etop_mdio_rd_xr9; ++ priv->mii_bus->write = ltq_etop_mdio_wr_xr9; ++ } else { ++ priv->mii_bus->read = ltq_etop_mdio_rd; ++ priv->mii_bus->write = ltq_etop_mdio_wr; ++ } + priv->mii_bus->name = "ltq_mii"; + snprintf(priv->mii_bus->id, MII_BUS_ID_SIZE, "%s-%x", + priv->pdev->name, priv->pdev->id); +@@ -430,17 +620,19 @@ static int + ltq_etop_open(struct net_device *dev) + { + struct ltq_etop_priv *priv = netdev_priv(dev); +- int i; ++ unsigned long flags; + +- for (i = 0; i < MAX_DMA_CHAN; i++) { +- struct ltq_etop_chan *ch = &priv->ch[i]; ++ napi_enable(&priv->txch.napi); ++ napi_enable(&priv->rxch.napi); ++ ++ spin_lock_irqsave(&priv->lock, flags); ++ ltq_dma_open(&priv->txch.dma); ++ ltq_dma_open(&priv->rxch.dma); ++ spin_unlock_irqrestore(&priv->lock, flags); ++ ++ if (dev->phydev) ++ phy_start(dev->phydev); + +- if (!IS_TX(i) && (!IS_RX(i))) +- continue; +- ltq_dma_open(&ch->dma); +- napi_enable(&ch->napi); +- } +- phy_start(dev->phydev); + netif_tx_start_all_queues(dev); + return 0; + } +@@ -449,18 +641,19 @@ static int + ltq_etop_stop(struct net_device *dev) + { + struct ltq_etop_priv *priv = netdev_priv(dev); +- int i; ++ unsigned long flags; + + netif_tx_stop_all_queues(dev); +- phy_stop(dev->phydev); +- for (i = 0; i < MAX_DMA_CHAN; i++) { +- struct ltq_etop_chan *ch = &priv->ch[i]; +- +- if (!IS_RX(i) && !IS_TX(i)) +- continue; +- napi_disable(&ch->napi); +- ltq_dma_close(&ch->dma); +- } ++ if (dev->phydev) ++ phy_stop(dev->phydev); ++ napi_disable(&priv->txch.napi); ++ napi_disable(&priv->rxch.napi); ++ ++ spin_lock_irqsave(&priv->lock, flags); ++ ltq_dma_close(&priv->txch.dma); ++ ltq_dma_close(&priv->rxch.dma); ++ spin_unlock_irqrestore(&priv->lock, flags); ++ + return 0; + } + +@@ -470,16 +663,16 @@ ltq_etop_tx(struct sk_buff *skb, struct + int queue = skb_get_queue_mapping(skb); + struct netdev_queue *txq = netdev_get_tx_queue(dev, queue); + struct ltq_etop_priv *priv = netdev_priv(dev); +- struct ltq_etop_chan *ch = &priv->ch[(queue << 1) | 1]; +- struct ltq_dma_desc *desc = &ch->dma.desc_base[ch->dma.desc]; +- int len; ++ struct ltq_dma_desc *desc = ++ &priv->txch.dma.desc_base[priv->txch.dma.desc]; + unsigned long flags; + u32 byte_offset; ++ int len; + + len = skb->len < ETH_ZLEN ? ETH_ZLEN : skb->len; + +- if ((desc->ctl & (LTQ_DMA_OWN | LTQ_DMA_C)) || ch->skb[ch->dma.desc]) { +- dev_kfree_skb_any(skb); ++ if ((desc->ctl & (LTQ_DMA_OWN | LTQ_DMA_C)) || ++ priv->txch.skb[priv->txch.dma.desc]) { + netdev_err(dev, "tx ring full\n"); + netif_tx_stop_queue(txq); + return NETDEV_TX_BUSY; +@@ -487,7 +680,7 @@ ltq_etop_tx(struct sk_buff *skb, struct + + /* dma needs to start on a 16 byte aligned address */ + byte_offset = CPHYSADDR(skb->data) % 16; +- ch->skb[ch->dma.desc] = skb; ++ priv->txch.skb[priv->txch.dma.desc] = skb; + + netif_trans_update(dev); + +@@ -497,11 +690,11 @@ ltq_etop_tx(struct sk_buff *skb, struct + wmb(); + desc->ctl = LTQ_DMA_OWN | LTQ_DMA_SOP | LTQ_DMA_EOP | + LTQ_DMA_TX_OFFSET(byte_offset) | (len & LTQ_DMA_SIZE_MASK); +- ch->dma.desc++; +- ch->dma.desc %= LTQ_DESC_NUM; ++ priv->txch.dma.desc++; ++ priv->txch.dma.desc %= LTQ_DESC_NUM; + spin_unlock_irqrestore(&priv->lock, flags); + +- if (ch->dma.desc_base[ch->dma.desc].ctl & LTQ_DMA_OWN) ++ if (priv->txch.dma.desc_base[priv->txch.dma.desc].ctl & LTQ_DMA_OWN) + netif_tx_stop_queue(txq); + + return NETDEV_TX_OK; +@@ -515,8 +708,10 @@ ltq_etop_change_mtu(struct net_device *d + + dev->mtu = new_mtu; + ++ int max = ETH_HLEN + VLAN_HLEN + new_mtu + ETH_FCS_LEN; ++ + spin_lock_irqsave(&priv->lock, flags); +- ltq_etop_w32((ETOP_PLEN_UNDER << 16) | new_mtu, LTQ_ETOP_IGPLEN); ++ ltq_etop_w32((ETOP_PLEN_UNDER << 16) | max, LTQ_ETOP_IGPLEN); + spin_unlock_irqrestore(&priv->lock, flags); + + return 0; +@@ -584,6 +779,9 @@ ltq_etop_init(struct net_device *dev) + if (err) + goto err_hw; + ltq_etop_change_mtu(dev, 1500); ++ err = ltq_etop_dma_init(dev); ++ if (err) ++ goto err_hw; + + memcpy(&mac, &priv->pldata->mac, sizeof(struct sockaddr)); + if (!is_valid_ether_addr(mac.sa_data)) { +@@ -601,9 +799,10 @@ ltq_etop_init(struct net_device *dev) + dev->addr_assign_type = NET_ADDR_RANDOM; + + ltq_etop_set_multicast_list(dev); +- err = ltq_etop_mdio_init(dev); +- if (err) +- goto err_netdev; ++ if (!ltq_etop_mdio_init(dev)) ++ dev->ethtool_ops = <q_etop_ethtool_ops; ++ else ++ pr_warn("etop: mdio probe failed\n");; + return 0; + + err_netdev: +@@ -623,6 +822,9 @@ ltq_etop_tx_timeout(struct net_device *d + err = ltq_etop_hw_init(dev); + if (err) + goto err_hw; ++ err = ltq_etop_dma_init(dev); ++ if (err) ++ goto err_hw; + netif_trans_update(dev); + netif_wake_queue(dev); + return; +@@ -646,14 +848,19 @@ static const struct net_device_ops ltq_e + .ndo_tx_timeout = ltq_etop_tx_timeout, + }; + +-static int __init +-ltq_etop_probe(struct platform_device *pdev) ++static int ltq_etop_probe(struct platform_device *pdev) + { + struct net_device *dev; + struct ltq_etop_priv *priv; +- struct resource *res; ++ struct resource *res, *gbit_res, irqres[2]; ++ const u8 *mac; + int err; +- int i; ++ ++ err = of_irq_to_resource_table(pdev->dev.of_node, irqres, 2); ++ if (err != 2) { ++ dev_err(&pdev->dev, "failed to get etop irqs\n"); ++ return -EINVAL; ++ } + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { +@@ -679,31 +886,62 @@ ltq_etop_probe(struct platform_device *p + goto err_out; + } + +- dev = alloc_etherdev_mq(sizeof(struct ltq_etop_priv), 4); +- if (!dev) { +- err = -ENOMEM; +- goto err_out; ++ if (of_machine_is_compatible("lantiq,ar9")) { ++ gbit_res = platform_get_resource(pdev, IORESOURCE_MEM, 1); ++ if (!gbit_res) { ++ dev_err(&pdev->dev, "failed to get gbit resource\n"); ++ err = -ENOENT; ++ goto err_out; ++ } ++ ltq_gbit_membase = devm_ioremap_nocache(&pdev->dev, ++ gbit_res->start, resource_size(gbit_res)); ++ if (!ltq_gbit_membase) { ++ dev_err(&pdev->dev, "failed to remap gigabit switch %d\n", ++ pdev->id); ++ err = -ENOMEM; ++ goto err_out; ++ } + } ++ ++ dev = alloc_etherdev_mq(sizeof(struct ltq_etop_priv), 4); + strcpy(dev->name, "eth%d"); + dev->netdev_ops = <q_eth_netdev_ops; +- dev->ethtool_ops = <q_etop_ethtool_ops; + priv = netdev_priv(dev); + priv->res = res; + priv->pdev = pdev; +- priv->pldata = dev_get_platdata(&pdev->dev); + priv->netdev = dev; ++ priv->tx_irq = irqres[0].start; ++ priv->rx_irq = irqres[1].start; ++ priv->mii_mode = of_get_phy_mode(pdev->dev.of_node); ++ ++ mac = of_get_mac_address(pdev->dev.of_node); ++ if (mac) ++ memcpy(priv->mac, mac, ETH_ALEN); ++ ++ priv->clk_ppe = clk_get(&pdev->dev, NULL); ++ if (IS_ERR(priv->clk_ppe)) ++ return PTR_ERR(priv->clk_ppe); ++ if (of_machine_is_compatible("lantiq,ar9")) { ++ priv->clk_switch = clk_get(&pdev->dev, "switch"); ++ if (IS_ERR(priv->clk_switch)) ++ return PTR_ERR(priv->clk_switch); ++ } ++ if (of_machine_is_compatible("lantiq,ase")) { ++ priv->clk_ephy = clk_get(&pdev->dev, "ephy"); ++ if (IS_ERR(priv->clk_ephy)) ++ return PTR_ERR(priv->clk_ephy); ++ priv->clk_ephycgu = clk_get(&pdev->dev, "ephycgu"); ++ if (IS_ERR(priv->clk_ephycgu)) ++ return PTR_ERR(priv->clk_ephycgu); ++ } ++ + spin_lock_init(&priv->lock); + SET_NETDEV_DEV(dev, &pdev->dev); + +- for (i = 0; i < MAX_DMA_CHAN; i++) { +- if (IS_TX(i)) +- netif_napi_add(dev, &priv->ch[i].napi, +- ltq_etop_poll_tx, 8); +- else if (IS_RX(i)) +- netif_napi_add(dev, &priv->ch[i].napi, +- ltq_etop_poll_rx, 32); +- priv->ch[i].netdev = dev; +- } ++ netif_napi_add(dev, &priv->txch.napi, ltq_etop_poll_tx, 8); ++ netif_napi_add(dev, &priv->rxch.napi, ltq_etop_poll_rx, 32); ++ priv->txch.netdev = dev; ++ priv->rxch.netdev = dev; + + err = register_netdev(dev); + if (err) +@@ -732,31 +970,22 @@ ltq_etop_remove(struct platform_device * + return 0; + } + ++static const struct of_device_id ltq_etop_match[] = { ++ { .compatible = "lantiq,etop-xway" }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, ltq_etop_match); ++ + static struct platform_driver ltq_mii_driver = { ++ .probe = ltq_etop_probe, + .remove = ltq_etop_remove, + .driver = { + .name = "ltq_etop", ++ .of_match_table = ltq_etop_match, + }, + }; + +-int __init +-init_ltq_etop(void) +-{ +- int ret = platform_driver_probe(<q_mii_driver, ltq_etop_probe); +- +- if (ret) +- pr_err("ltq_etop: Error registering platform driver!"); +- return ret; +-} +- +-static void __exit +-exit_ltq_etop(void) +-{ +- platform_driver_unregister(<q_mii_driver); +-} +- +-module_init(init_ltq_etop); +-module_exit(exit_ltq_etop); ++module_platform_driver(ltq_mii_driver); + + MODULE_AUTHOR("John Crispin "); + MODULE_DESCRIPTION("Lantiq SoC ETOP"); diff --git a/target/linux/lantiq/patches-4.19/0030-GPIO-add-named-gpio-exports.patch b/target/linux/lantiq/patches-4.19/0030-GPIO-add-named-gpio-exports.patch new file mode 100644 index 0000000000..fe4ea4fc24 --- /dev/null +++ b/target/linux/lantiq/patches-4.19/0030-GPIO-add-named-gpio-exports.patch @@ -0,0 +1,169 @@ +From cc809a441d8f2924f785eb863dfa6aef47a25b0b Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Tue, 12 Aug 2014 20:49:27 +0200 +Subject: [PATCH 30/36] GPIO: add named gpio exports + +Signed-off-by: John Crispin +--- + drivers/gpio/gpiolib-of.c | 68 +++++++++++++++++++++++++++++++++++++++++ + drivers/gpio/gpiolib.c | 11 +++++-- + include/asm-generic/gpio.h | 5 +++ + include/linux/gpio/consumer.h | 8 +++++ + 4 files changed, 90 insertions(+), 2 deletions(-) + +--- a/drivers/gpio/gpiolib-of.c ++++ b/drivers/gpio/gpiolib-of.c +@@ -23,6 +23,8 @@ + #include + #include + #include ++#include ++#include + + #include "gpiolib.h" + +@@ -507,3 +509,72 @@ void of_gpiochip_remove(struct gpio_chip + gpiochip_remove_pin_ranges(chip); + of_node_put(chip->of_node); + } ++ ++#ifdef CONFIG_GPIO_SYSFS ++ ++static struct of_device_id gpio_export_ids[] = { ++ { .compatible = "gpio-export" }, ++ { /* sentinel */ } ++}; ++ ++static int of_gpio_export_probe(struct platform_device *pdev) ++{ ++ struct device_node *np = pdev->dev.of_node; ++ struct device_node *cnp; ++ u32 val; ++ int nb = 0; ++ ++ for_each_child_of_node(np, cnp) { ++ const char *name = NULL; ++ int gpio; ++ bool dmc; ++ int max_gpio = 1; ++ int i; ++ ++ of_property_read_string(cnp, "gpio-export,name", &name); ++ ++ if (!name) ++ max_gpio = of_gpio_count(cnp); ++ ++ for (i = 0; i < max_gpio; i++) { ++ unsigned flags = 0; ++ enum of_gpio_flags of_flags; ++ ++ gpio = of_get_gpio_flags(cnp, i, &of_flags); ++ if (!gpio_is_valid(gpio)) ++ return gpio; ++ ++ if (of_flags == OF_GPIO_ACTIVE_LOW) ++ flags |= GPIOF_ACTIVE_LOW; ++ ++ if (!of_property_read_u32(cnp, "gpio-export,output", &val)) ++ flags |= val ? GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW; ++ else ++ flags |= GPIOF_IN; ++ ++ if (devm_gpio_request_one(&pdev->dev, gpio, flags, name ? name : of_node_full_name(np))) ++ continue; ++ ++ dmc = of_property_read_bool(cnp, "gpio-export,direction_may_change"); ++ gpio_export_with_name(gpio, dmc, name); ++ nb++; ++ } ++ } ++ ++ dev_info(&pdev->dev, "%d gpio(s) exported\n", nb); ++ ++ return 0; ++} ++ ++static struct platform_driver gpio_export_driver = { ++ .driver = { ++ .name = "gpio-export", ++ .owner = THIS_MODULE, ++ .of_match_table = of_match_ptr(gpio_export_ids), ++ }, ++ .probe = of_gpio_export_probe, ++}; ++ ++module_platform_driver(gpio_export_driver); ++ ++#endif +--- a/include/asm-generic/gpio.h ++++ b/include/asm-generic/gpio.h +@@ -127,6 +127,12 @@ static inline int gpio_export(unsigned g + return gpiod_export(gpio_to_desc(gpio), direction_may_change); + } + ++int __gpiod_export(struct gpio_desc *desc, bool direction_may_change, const char *name); ++static inline int gpio_export_with_name(unsigned gpio, bool direction_may_change, const char *name) ++{ ++ return __gpiod_export(gpio_to_desc(gpio), direction_may_change, name); ++} ++ + static inline int gpio_export_link(struct device *dev, const char *name, + unsigned gpio) + { +--- a/include/linux/gpio/consumer.h ++++ b/include/linux/gpio/consumer.h +@@ -451,6 +451,7 @@ struct gpio_desc *devm_fwnode_get_gpiod_ + + #if IS_ENABLED(CONFIG_GPIOLIB) && IS_ENABLED(CONFIG_GPIO_SYSFS) + ++int _gpiod_export(struct gpio_desc *desc, bool direction_may_change, const char *name); + int gpiod_export(struct gpio_desc *desc, bool direction_may_change); + int gpiod_export_link(struct device *dev, const char *name, + struct gpio_desc *desc); +@@ -458,6 +459,13 @@ void gpiod_unexport(struct gpio_desc *de + + #else /* CONFIG_GPIOLIB && CONFIG_GPIO_SYSFS */ + ++static inline int _gpiod_export(struct gpio_desc *desc, ++ bool direction_may_change, ++ const char *name) ++{ ++ return -ENOSYS; ++} ++ + static inline int gpiod_export(struct gpio_desc *desc, + bool direction_may_change) + { +--- a/drivers/gpio/gpiolib-sysfs.c ++++ b/drivers/gpio/gpiolib-sysfs.c +@@ -553,7 +553,7 @@ static struct class gpio_class = { + * + * Returns zero on success, else an error. + */ +-int gpiod_export(struct gpio_desc *desc, bool direction_may_change) ++int __gpiod_export(struct gpio_desc *desc, bool direction_may_change, const char *name) + { + struct gpio_chip *chip; + struct gpio_device *gdev; +@@ -615,6 +615,8 @@ int gpiod_export(struct gpio_desc *desc, + offset = gpio_chip_hwgpio(desc); + if (chip->names && chip->names[offset]) + ioname = chip->names[offset]; ++ if (name) ++ ioname = name; + + dev = device_create_with_groups(&gpio_class, &gdev->dev, + MKDEV(0, 0), data, gpio_groups, +@@ -636,6 +638,12 @@ err_unlock: + gpiod_dbg(desc, "%s: status %d\n", __func__, status); + return status; + } ++EXPORT_SYMBOL_GPL(__gpiod_export); ++ ++int gpiod_export(struct gpio_desc *desc, bool direction_may_change) ++{ ++ return __gpiod_export(desc, direction_may_change, NULL); ++} + EXPORT_SYMBOL_GPL(gpiod_export); + + static int match_export(struct device *dev, const void *desc) diff --git a/target/linux/lantiq/patches-4.19/0031-I2C-MIPS-lantiq-add-FALC-ON-i2c-bus-master.patch b/target/linux/lantiq/patches-4.19/0031-I2C-MIPS-lantiq-add-FALC-ON-i2c-bus-master.patch new file mode 100644 index 0000000000..a1e1cceddc --- /dev/null +++ b/target/linux/lantiq/patches-4.19/0031-I2C-MIPS-lantiq-add-FALC-ON-i2c-bus-master.patch @@ -0,0 +1,1034 @@ +From f17e50f67fa3c77624edf2ca03fae0d50f0ce39b Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Thu, 7 Aug 2014 18:26:42 +0200 +Subject: [PATCH 31/36] I2C: MIPS: lantiq: add FALC-ON i2c bus master + +This patch adds the driver needed to make the I2C bus work on FALC-ON SoCs. + +Signed-off-by: Thomas Langer +Signed-off-by: John Crispin +--- + drivers/i2c/busses/Kconfig | 10 + + drivers/i2c/busses/Makefile | 1 + + drivers/i2c/busses/i2c-lantiq.c | 747 +++++++++++++++++++++++++++++++++++++++ + drivers/i2c/busses/i2c-lantiq.h | 234 ++++++++++++ + 4 files changed, 992 insertions(+) + create mode 100644 drivers/i2c/busses/i2c-lantiq.c + create mode 100644 drivers/i2c/busses/i2c-lantiq.h + +--- a/drivers/i2c/busses/Kconfig ++++ b/drivers/i2c/busses/Kconfig +@@ -696,6 +696,16 @@ config I2C_MESON + If you say yes to this option, support will be included for the + I2C interface on the Amlogic Meson family of SoCs. + ++config I2C_LANTIQ ++ tristate "Lantiq I2C interface" ++ depends on LANTIQ && SOC_FALCON ++ help ++ If you say yes to this option, support will be included for the ++ Lantiq I2C core. ++ ++ This driver can also be built as a module. If so, the module ++ will be called i2c-lantiq. ++ + config I2C_MPC + tristate "MPC107/824x/85xx/512x/52xx/83xx/86xx" + depends on PPC +--- a/drivers/i2c/busses/Makefile ++++ b/drivers/i2c/busses/Makefile +@@ -68,6 +68,7 @@ obj-$(CONFIG_I2C_IMX_LPI2C) += i2c-imx-l + obj-$(CONFIG_I2C_IOP3XX) += i2c-iop3xx.o + obj-$(CONFIG_I2C_JZ4780) += i2c-jz4780.o + obj-$(CONFIG_I2C_KEMPLD) += i2c-kempld.o ++obj-$(CONFIG_I2C_LANTIQ) += i2c-lantiq.o + obj-$(CONFIG_I2C_LPC2K) += i2c-lpc2k.o + obj-$(CONFIG_I2C_MESON) += i2c-meson.o + obj-$(CONFIG_I2C_MPC) += i2c-mpc.o +--- /dev/null ++++ b/drivers/i2c/busses/i2c-lantiq.c +@@ -0,0 +1,747 @@ ++ ++/* ++ * Lantiq I2C bus adapter ++ * ++ * Parts based on i2c-designware.c and other i2c drivers from Linux 2.6.33 ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License as published by ++ * the Free Software Foundation; either version 2 of the License, or ++ * (at your option) any later version. ++ * ++ * This program is distributed in the hope that it will be useful, ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ * ++ * You should have received a copy of the GNU General Public License ++ * along with this program; if not, write to the Free Software ++ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. ++ * ++ * Copyright (C) 2012 Thomas Langer ++ */ ++ ++#include ++#include ++#include ++#include /* for kzalloc, kfree */ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++#include "i2c-lantiq.h" ++ ++/* ++ * CURRENT ISSUES: ++ * - no high speed support ++ * - ten bit mode is not tested (no slave devices) ++ */ ++ ++/* access macros */ ++#define i2c_r32(reg) \ ++ __raw_readl(&(priv->membase)->reg) ++#define i2c_w32(val, reg) \ ++ __raw_writel(val, &(priv->membase)->reg) ++#define i2c_w32_mask(clear, set, reg) \ ++ i2c_w32((i2c_r32(reg) & ~(clear)) | (set), reg) ++ ++#define DRV_NAME "i2c-lantiq" ++#define DRV_VERSION "1.00" ++ ++#define LTQ_I2C_BUSY_TIMEOUT 20 /* ms */ ++ ++#ifdef DEBUG ++#define LTQ_I2C_XFER_TIMEOUT (25*HZ) ++#else ++#define LTQ_I2C_XFER_TIMEOUT HZ ++#endif ++ ++#define LTQ_I2C_IMSC_DEFAULT_MASK (I2C_IMSC_I2C_P_INT_EN | \ ++ I2C_IMSC_I2C_ERR_INT_EN) ++ ++#define LTQ_I2C_ARB_LOST (1 << 0) ++#define LTQ_I2C_NACK (1 << 1) ++#define LTQ_I2C_RX_UFL (1 << 2) ++#define LTQ_I2C_RX_OFL (1 << 3) ++#define LTQ_I2C_TX_UFL (1 << 4) ++#define LTQ_I2C_TX_OFL (1 << 5) ++ ++struct ltq_i2c { ++ struct mutex mutex; ++ ++ ++ /* active clock settings */ ++ unsigned int input_clock; /* clock input for i2c hardware block */ ++ unsigned int i2c_clock; /* approximated bus clock in kHz */ ++ ++ struct clk *clk_gate; ++ struct clk *clk_input; ++ ++ ++ /* resources (memory and interrupts) */ ++ int irq_lb; /* last burst irq */ ++ ++ struct lantiq_reg_i2c __iomem *membase; /* base of mapped registers */ ++ ++ struct i2c_adapter adap; ++ struct device *dev; ++ ++ struct completion cmd_complete; ++ ++ ++ /* message transfer data */ ++ struct i2c_msg *current_msg; /* current message */ ++ int msgs_num; /* number of messages to handle */ ++ u8 *msg_buf; /* current buffer */ ++ u32 msg_buf_len; /* remaining length of current buffer */ ++ int msg_err; /* error status of the current transfer */ ++ ++ ++ /* master status codes */ ++ enum { ++ STATUS_IDLE, ++ STATUS_ADDR, /* address phase */ ++ STATUS_WRITE, ++ STATUS_READ, ++ STATUS_READ_END, ++ STATUS_STOP ++ } status; ++}; ++ ++static irqreturn_t ltq_i2c_isr(int irq, void *dev_id); ++ ++static inline void enable_burst_irq(struct ltq_i2c *priv) ++{ ++ i2c_w32_mask(0, I2C_IMSC_LBREQ_INT_EN | I2C_IMSC_BREQ_INT_EN, imsc); ++} ++static inline void disable_burst_irq(struct ltq_i2c *priv) ++{ ++ i2c_w32_mask(I2C_IMSC_LBREQ_INT_EN | I2C_IMSC_BREQ_INT_EN, 0, imsc); ++} ++ ++static void prepare_msg_send_addr(struct ltq_i2c *priv) ++{ ++ struct i2c_msg *msg = priv->current_msg; ++ int rd = !!(msg->flags & I2C_M_RD); /* extends to 0 or 1 */ ++ u16 addr = msg->addr; ++ ++ /* new i2c_msg */ ++ priv->msg_buf = msg->buf; ++ priv->msg_buf_len = msg->len; ++ if (rd) ++ priv->status = STATUS_READ; ++ else ++ priv->status = STATUS_WRITE; ++ ++ /* send slave address */ ++ if (msg->flags & I2C_M_TEN) { ++ i2c_w32(0xf0 | ((addr & 0x300) >> 7) | rd, txd); ++ i2c_w32(addr & 0xff, txd); ++ } else { ++ i2c_w32((addr & 0x7f) << 1 | rd, txd); ++ } ++} ++ ++static void ltq_i2c_set_tx_len(struct ltq_i2c *priv) ++{ ++ struct i2c_msg *msg = priv->current_msg; ++ int len = (msg->flags & I2C_M_TEN) ? 2 : 1; ++ ++ pr_debug("set_tx_len %cX\n", (msg->flags & I2C_M_RD) ? 'R' : 'T'); ++ ++ priv->status = STATUS_ADDR; ++ ++ if (!(msg->flags & I2C_M_RD)) ++ len += msg->len; ++ else ++ /* set maximum received packet size (before rx int!) */ ++ i2c_w32(msg->len, mrps_ctrl); ++ i2c_w32(len, tps_ctrl); ++ enable_burst_irq(priv); ++} ++ ++static int ltq_i2c_hw_set_clock(struct i2c_adapter *adap) ++{ ++ struct ltq_i2c *priv = i2c_get_adapdata(adap); ++ unsigned int input_clock = clk_get_rate(priv->clk_input); ++ u32 dec, inc = 1; ++ ++ /* clock changed? */ ++ if (priv->input_clock == input_clock) ++ return 0; ++ ++ /* ++ * this formula is only an approximation, found by the recommended ++ * values in the "I2C Architecture Specification 1.7.1" ++ */ ++ dec = input_clock / (priv->i2c_clock * 2); ++ if (dec <= 6) ++ return -ENXIO; ++ ++ i2c_w32(0, fdiv_high_cfg); ++ i2c_w32((inc << I2C_FDIV_CFG_INC_OFFSET) | ++ (dec << I2C_FDIV_CFG_DEC_OFFSET), ++ fdiv_cfg); ++ ++ dev_info(priv->dev, "setup clocks (in %d kHz, bus %d kHz, dec=%d)\n", ++ input_clock, priv->i2c_clock, dec); ++ ++ priv->input_clock = input_clock; ++ return 0; ++} ++ ++static int ltq_i2c_hw_init(struct i2c_adapter *adap) ++{ ++ int ret = 0; ++ struct ltq_i2c *priv = i2c_get_adapdata(adap); ++ ++ /* disable bus */ ++ i2c_w32_mask(I2C_RUN_CTRL_RUN_EN, 0, run_ctrl); ++ ++#ifndef DEBUG ++ /* set normal operation clock divider */ ++ i2c_w32(1 << I2C_CLC_RMC_OFFSET, clc); ++#else ++ /* for debugging a higher divider value! */ ++ i2c_w32(0xF0 << I2C_CLC_RMC_OFFSET, clc); ++#endif ++ ++ /* setup clock */ ++ ret = ltq_i2c_hw_set_clock(adap); ++ if (ret != 0) { ++ dev_warn(priv->dev, "invalid clock settings\n"); ++ return ret; ++ } ++ ++ /* configure fifo */ ++ i2c_w32(I2C_FIFO_CFG_TXFC | /* tx fifo as flow controller */ ++ I2C_FIFO_CFG_RXFC | /* rx fifo as flow controller */ ++ I2C_FIFO_CFG_TXFA_TXFA2 | /* tx fifo 4-byte aligned */ ++ I2C_FIFO_CFG_RXFA_RXFA2 | /* rx fifo 4-byte aligned */ ++ I2C_FIFO_CFG_TXBS_TXBS0 | /* tx fifo burst size is 1 word */ ++ I2C_FIFO_CFG_RXBS_RXBS0, /* rx fifo burst size is 1 word */ ++ fifo_cfg); ++ ++ /* configure address */ ++ i2c_w32(I2C_ADDR_CFG_SOPE_EN | /* generate stop when no more data in ++ the fifo */ ++ I2C_ADDR_CFG_SONA_EN | /* generate stop when NA received */ ++ I2C_ADDR_CFG_MnS_EN | /* we are master device */ ++ 0, /* our slave address (not used!) */ ++ addr_cfg); ++ ++ /* enable bus */ ++ i2c_w32_mask(0, I2C_RUN_CTRL_RUN_EN, run_ctrl); ++ ++ return 0; ++} ++ ++static int ltq_i2c_wait_bus_not_busy(struct ltq_i2c *priv) ++{ ++ unsigned long timeout; ++ ++ timeout = jiffies + msecs_to_jiffies(LTQ_I2C_BUSY_TIMEOUT); ++ ++ do { ++ u32 stat = i2c_r32(bus_stat); ++ ++ if ((stat & I2C_BUS_STAT_BS_MASK) == I2C_BUS_STAT_BS_FREE) ++ return 0; ++ ++ cond_resched(); ++ } while (!time_after_eq(jiffies, timeout)); ++ ++ dev_err(priv->dev, "timeout waiting for bus ready\n"); ++ return -ETIMEDOUT; ++} ++ ++static void ltq_i2c_tx(struct ltq_i2c *priv, int last) ++{ ++ if (priv->msg_buf_len && priv->msg_buf) { ++ i2c_w32(*priv->msg_buf, txd); ++ ++ if (--priv->msg_buf_len) ++ priv->msg_buf++; ++ else ++ priv->msg_buf = NULL; ++ } else { ++ last = 1; ++ } ++ ++ if (last) ++ disable_burst_irq(priv); ++} ++ ++static void ltq_i2c_rx(struct ltq_i2c *priv, int last) ++{ ++ u32 fifo_stat, timeout; ++ if (priv->msg_buf_len && priv->msg_buf) { ++ timeout = 5000000; ++ do { ++ fifo_stat = i2c_r32(ffs_stat); ++ } while (!fifo_stat && --timeout); ++ if (!timeout) { ++ last = 1; ++ pr_debug("\nrx timeout\n"); ++ goto err; ++ } ++ while (fifo_stat) { ++ *priv->msg_buf = i2c_r32(rxd); ++ if (--priv->msg_buf_len) { ++ priv->msg_buf++; ++ } else { ++ priv->msg_buf = NULL; ++ last = 1; ++ break; ++ } ++ /* ++ * do not read more than burst size, otherwise no "last ++ * burst" is generated and the transaction is blocked! ++ */ ++ fifo_stat = 0; ++ } ++ } else { ++ last = 1; ++ } ++err: ++ if (last) { ++ disable_burst_irq(priv); ++ ++ if (priv->status == STATUS_READ_END) { ++ /* ++ * do the STATUS_STOP and complete() here, as sometimes ++ * the tx_end is already seen before this is finished ++ */ ++ priv->status = STATUS_STOP; ++ complete(&priv->cmd_complete); ++ } else { ++ i2c_w32(I2C_ENDD_CTRL_SETEND, endd_ctrl); ++ priv->status = STATUS_READ_END; ++ } ++ } ++} ++ ++static void ltq_i2c_xfer_init(struct ltq_i2c *priv) ++{ ++ /* enable interrupts */ ++ i2c_w32(LTQ_I2C_IMSC_DEFAULT_MASK, imsc); ++ ++ /* trigger transfer of first msg */ ++ ltq_i2c_set_tx_len(priv); ++} ++ ++static void dump_msgs(struct i2c_msg msgs[], int num, int rx) ++{ ++#if defined(DEBUG) ++ int i, j; ++ pr_debug("Messages %d %s\n", num, rx ? "out" : "in"); ++ for (i = 0; i < num; i++) { ++ pr_debug("%2d %cX Msg(%d) addr=0x%X: ", i, ++ (msgs[i].flags & I2C_M_RD) ? 'R' : 'T', ++ msgs[i].len, msgs[i].addr); ++ if (!(msgs[i].flags & I2C_M_RD) || rx) { ++ for (j = 0; j < msgs[i].len; j++) ++ pr_debug("%02X ", msgs[i].buf[j]); ++ } ++ pr_debug("\n"); ++ } ++#endif ++} ++ ++static void ltq_i2c_release_bus(struct ltq_i2c *priv) ++{ ++ if ((i2c_r32(bus_stat) & I2C_BUS_STAT_BS_MASK) == I2C_BUS_STAT_BS_BM) ++ i2c_w32(I2C_ENDD_CTRL_SETEND, endd_ctrl); ++} ++ ++static int ltq_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], ++ int num) ++{ ++ struct ltq_i2c *priv = i2c_get_adapdata(adap); ++ int ret; ++ ++ dev_dbg(priv->dev, "xfer %u messages\n", num); ++ dump_msgs(msgs, num, 0); ++ ++ mutex_lock(&priv->mutex); ++ ++ init_completion(&priv->cmd_complete); ++ priv->current_msg = msgs; ++ priv->msgs_num = num; ++ priv->msg_err = 0; ++ priv->status = STATUS_IDLE; ++ ++ /* wait for the bus to become ready */ ++ ret = ltq_i2c_wait_bus_not_busy(priv); ++ if (ret) ++ goto done; ++ ++ while (priv->msgs_num) { ++ /* start the transfers */ ++ ltq_i2c_xfer_init(priv); ++ ++ /* wait for transfers to complete */ ++ ret = wait_for_completion_interruptible_timeout( ++ &priv->cmd_complete, LTQ_I2C_XFER_TIMEOUT); ++ if (ret == 0) { ++ dev_err(priv->dev, "controller timed out\n"); ++ ltq_i2c_hw_init(adap); ++ ret = -ETIMEDOUT; ++ goto done; ++ } else if (ret < 0) ++ goto done; ++ ++ if (priv->msg_err) { ++ if (priv->msg_err & LTQ_I2C_NACK) ++ ret = -ENXIO; ++ else ++ ret = -EREMOTEIO; ++ goto done; ++ } ++ if (--priv->msgs_num) ++ priv->current_msg++; ++ } ++ /* no error? */ ++ ret = num; ++ ++done: ++ ltq_i2c_release_bus(priv); ++ ++ mutex_unlock(&priv->mutex); ++ ++ if (ret >= 0) ++ dump_msgs(msgs, num, 1); ++ ++ pr_debug("XFER ret %d\n", ret); ++ return ret; ++} ++ ++static irqreturn_t ltq_i2c_isr_burst(int irq, void *dev_id) ++{ ++ struct ltq_i2c *priv = dev_id; ++ struct i2c_msg *msg = priv->current_msg; ++ int last = (irq == priv->irq_lb); ++ ++ if (last) ++ pr_debug("LB "); ++ else ++ pr_debug("B "); ++ ++ if (msg->flags & I2C_M_RD) { ++ switch (priv->status) { ++ case STATUS_ADDR: ++ pr_debug("X"); ++ prepare_msg_send_addr(priv); ++ disable_burst_irq(priv); ++ break; ++ case STATUS_READ: ++ case STATUS_READ_END: ++ pr_debug("R"); ++ ltq_i2c_rx(priv, last); ++ break; ++ default: ++ disable_burst_irq(priv); ++ pr_warn("Status R %d\n", priv->status); ++ break; ++ } ++ } else { ++ switch (priv->status) { ++ case STATUS_ADDR: ++ pr_debug("x"); ++ prepare_msg_send_addr(priv); ++ break; ++ case STATUS_WRITE: ++ pr_debug("w"); ++ ltq_i2c_tx(priv, last); ++ break; ++ default: ++ disable_burst_irq(priv); ++ pr_warn("Status W %d\n", priv->status); ++ break; ++ } ++ } ++ ++ i2c_w32(I2C_ICR_BREQ_INT_CLR | I2C_ICR_LBREQ_INT_CLR, icr); ++ return IRQ_HANDLED; ++} ++ ++static void ltq_i2c_isr_prot(struct ltq_i2c *priv) ++{ ++ u32 i_pro = i2c_r32(p_irqss); ++ ++ pr_debug("i2c-p"); ++ ++ /* not acknowledge */ ++ if (i_pro & I2C_P_IRQSS_NACK) { ++ priv->msg_err |= LTQ_I2C_NACK; ++ pr_debug(" nack"); ++ } ++ ++ /* arbitration lost */ ++ if (i_pro & I2C_P_IRQSS_AL) { ++ priv->msg_err |= LTQ_I2C_ARB_LOST; ++ pr_debug(" arb-lost"); ++ } ++ /* tx -> rx switch */ ++ if (i_pro & I2C_P_IRQSS_RX) ++ pr_debug(" rx"); ++ ++ /* tx end */ ++ if (i_pro & I2C_P_IRQSS_TX_END) ++ pr_debug(" txend"); ++ pr_debug("\n"); ++ ++ if (!priv->msg_err) { ++ /* tx -> rx switch */ ++ if (i_pro & I2C_P_IRQSS_RX) { ++ priv->status = STATUS_READ; ++ enable_burst_irq(priv); ++ } ++ if (i_pro & I2C_P_IRQSS_TX_END) { ++ if (priv->status == STATUS_READ) ++ priv->status = STATUS_READ_END; ++ else { ++ disable_burst_irq(priv); ++ priv->status = STATUS_STOP; ++ } ++ } ++ } ++ ++ i2c_w32(i_pro, p_irqsc); ++} ++ ++static irqreturn_t ltq_i2c_isr(int irq, void *dev_id) ++{ ++ u32 i_raw, i_err = 0; ++ struct ltq_i2c *priv = dev_id; ++ ++ i_raw = i2c_r32(mis); ++ pr_debug("i_raw 0x%08X\n", i_raw); ++ ++ /* error interrupt */ ++ if (i_raw & I2C_RIS_I2C_ERR_INT_INTOCC) { ++ i_err = i2c_r32(err_irqss); ++ pr_debug("i_err 0x%08X bus_stat 0x%04X\n", ++ i_err, i2c_r32(bus_stat)); ++ ++ /* tx fifo overflow (8) */ ++ if (i_err & I2C_ERR_IRQSS_TXF_OFL) ++ priv->msg_err |= LTQ_I2C_TX_OFL; ++ ++ /* tx fifo underflow (4) */ ++ if (i_err & I2C_ERR_IRQSS_TXF_UFL) ++ priv->msg_err |= LTQ_I2C_TX_UFL; ++ ++ /* rx fifo overflow (2) */ ++ if (i_err & I2C_ERR_IRQSS_RXF_OFL) ++ priv->msg_err |= LTQ_I2C_RX_OFL; ++ ++ /* rx fifo underflow (1) */ ++ if (i_err & I2C_ERR_IRQSS_RXF_UFL) ++ priv->msg_err |= LTQ_I2C_RX_UFL; ++ ++ i2c_w32(i_err, err_irqsc); ++ } ++ ++ /* protocol interrupt */ ++ if (i_raw & I2C_RIS_I2C_P_INT_INTOCC) ++ ltq_i2c_isr_prot(priv); ++ ++ if ((priv->msg_err) || (priv->status == STATUS_STOP)) ++ complete(&priv->cmd_complete); ++ ++ return IRQ_HANDLED; ++} ++ ++static u32 ltq_i2c_functionality(struct i2c_adapter *adap) ++{ ++ return I2C_FUNC_I2C | ++ I2C_FUNC_10BIT_ADDR | ++ I2C_FUNC_SMBUS_EMUL; ++} ++ ++static struct i2c_algorithm ltq_i2c_algorithm = { ++ .master_xfer = ltq_i2c_xfer, ++ .functionality = ltq_i2c_functionality, ++}; ++ ++static int ltq_i2c_probe(struct platform_device *pdev) ++{ ++ struct device_node *node = pdev->dev.of_node; ++ struct ltq_i2c *priv; ++ struct i2c_adapter *adap; ++ struct resource *mmres, irqres[4]; ++ int ret = 0; ++ ++ dev_dbg(&pdev->dev, "probing\n"); ++ ++ mmres = platform_get_resource(pdev, IORESOURCE_MEM, 0); ++ ret = of_irq_to_resource_table(node, irqres, 4); ++ if (!mmres || (ret != 4)) { ++ dev_err(&pdev->dev, "no resources\n"); ++ return -ENODEV; ++ } ++ ++ /* allocate private data */ ++ priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); ++ if (!priv) { ++ dev_err(&pdev->dev, "can't allocate private data\n"); ++ return -ENOMEM; ++ } ++ ++ adap = &priv->adap; ++ i2c_set_adapdata(adap, priv); ++ adap->owner = THIS_MODULE; ++ adap->class = I2C_CLASS_HWMON | I2C_CLASS_SPD; ++ strlcpy(adap->name, DRV_NAME "-adapter", sizeof(adap->name)); ++ adap->algo = <q_i2c_algorithm; ++ adap->dev.parent = &pdev->dev; ++ adap->dev.of_node = pdev->dev.of_node; ++ ++ if (of_property_read_u32(node, "clock-frequency", &priv->i2c_clock)) { ++ dev_warn(&pdev->dev, "No I2C speed selected, using 100kHz\n"); ++ priv->i2c_clock = 100000; ++ } ++ ++ init_completion(&priv->cmd_complete); ++ mutex_init(&priv->mutex); ++ ++ priv->membase = devm_ioremap_resource(&pdev->dev, mmres); ++ if (IS_ERR(priv->membase)) ++ return PTR_ERR(priv->membase); ++ ++ priv->dev = &pdev->dev; ++ priv->irq_lb = irqres[0].start; ++ ++ ret = devm_request_irq(&pdev->dev, irqres[0].start, ltq_i2c_isr_burst, ++ 0x0, "i2c lb", priv); ++ if (ret) { ++ dev_err(&pdev->dev, "can't get last burst IRQ %d\n", ++ irqres[0].start); ++ return -ENODEV; ++ } ++ ++ ret = devm_request_irq(&pdev->dev, irqres[1].start, ltq_i2c_isr_burst, ++ 0x0, "i2c b", priv); ++ if (ret) { ++ dev_err(&pdev->dev, "can't get burst IRQ %d\n", ++ irqres[1].start); ++ return -ENODEV; ++ } ++ ++ ret = devm_request_irq(&pdev->dev, irqres[2].start, ltq_i2c_isr, ++ 0x0, "i2c err", priv); ++ if (ret) { ++ dev_err(&pdev->dev, "can't get error IRQ %d\n", ++ irqres[2].start); ++ return -ENODEV; ++ } ++ ++ ret = devm_request_irq(&pdev->dev, irqres[3].start, ltq_i2c_isr, ++ 0x0, "i2c p", priv); ++ if (ret) { ++ dev_err(&pdev->dev, "can't get protocol IRQ %d\n", ++ irqres[3].start); ++ return -ENODEV; ++ } ++ ++ dev_dbg(&pdev->dev, "mapped io-space to %p\n", priv->membase); ++ dev_dbg(&pdev->dev, "use IRQs %d, %d, %d, %d\n", irqres[0].start, ++ irqres[1].start, irqres[2].start, irqres[3].start); ++ ++ priv->clk_gate = devm_clk_get(&pdev->dev, NULL); ++ if (IS_ERR(priv->clk_gate)) { ++ dev_err(&pdev->dev, "failed to get i2c clk\n"); ++ return -ENOENT; ++ } ++ ++ /* this is a static clock, which has no refcounting */ ++ priv->clk_input = clk_get_fpi(); ++ if (IS_ERR(priv->clk_input)) { ++ dev_err(&pdev->dev, "failed to get fpi clk\n"); ++ return -ENOENT; ++ } ++ ++ clk_activate(priv->clk_gate); ++ ++ /* add our adapter to the i2c stack */ ++ ret = i2c_add_numbered_adapter(adap); ++ if (ret) { ++ dev_err(&pdev->dev, "can't register I2C adapter\n"); ++ goto out; ++ } ++ ++ platform_set_drvdata(pdev, priv); ++ i2c_set_adapdata(adap, priv); ++ ++ /* print module version information */ ++ dev_dbg(&pdev->dev, "module id=%u revision=%u\n", ++ (i2c_r32(id) & I2C_ID_ID_MASK) >> I2C_ID_ID_OFFSET, ++ (i2c_r32(id) & I2C_ID_REV_MASK) >> I2C_ID_REV_OFFSET); ++ ++ /* initialize HW */ ++ ret = ltq_i2c_hw_init(adap); ++ if (ret) { ++ dev_err(&pdev->dev, "can't configure adapter\n"); ++ i2c_del_adapter(adap); ++ platform_set_drvdata(pdev, NULL); ++ goto out; ++ } else { ++ dev_info(&pdev->dev, "version %s\n", DRV_VERSION); ++ } ++ ++out: ++ /* if init failed, we need to deactivate the clock gate */ ++ if (ret) ++ clk_deactivate(priv->clk_gate); ++ ++ return ret; ++} ++ ++static int ltq_i2c_remove(struct platform_device *pdev) ++{ ++ struct ltq_i2c *priv = platform_get_drvdata(pdev); ++ ++ /* disable bus */ ++ i2c_w32_mask(I2C_RUN_CTRL_RUN_EN, 0, run_ctrl); ++ ++ /* power down the core */ ++ clk_deactivate(priv->clk_gate); ++ ++ /* remove driver */ ++ i2c_del_adapter(&priv->adap); ++ kfree(priv); ++ ++ dev_dbg(&pdev->dev, "removed\n"); ++ platform_set_drvdata(pdev, NULL); ++ ++ return 0; ++} ++static const struct of_device_id ltq_i2c_match[] = { ++ { .compatible = "lantiq,lantiq-i2c" }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, ltq_i2c_match); ++ ++static struct platform_driver ltq_i2c_driver = { ++ .probe = ltq_i2c_probe, ++ .remove = ltq_i2c_remove, ++ .driver = { ++ .name = DRV_NAME, ++ .owner = THIS_MODULE, ++ .of_match_table = ltq_i2c_match, ++ }, ++}; ++ ++module_platform_driver(ltq_i2c_driver); ++ ++MODULE_DESCRIPTION("Lantiq I2C bus adapter"); ++MODULE_AUTHOR("Thomas Langer "); ++MODULE_ALIAS("platform:" DRV_NAME); ++MODULE_LICENSE("GPL"); ++MODULE_VERSION(DRV_VERSION); +--- /dev/null ++++ b/drivers/i2c/busses/i2c-lantiq.h +@@ -0,0 +1,234 @@ ++#ifndef I2C_LANTIQ_H ++#define I2C_LANTIQ_H ++ ++/* I2C register structure */ ++struct lantiq_reg_i2c { ++ /* I2C Kernel Clock Control Register */ ++ unsigned int clc; /* 0x00000000 */ ++ /* Reserved */ ++ unsigned int res_0; /* 0x00000004 */ ++ /* I2C Identification Register */ ++ unsigned int id; /* 0x00000008 */ ++ /* Reserved */ ++ unsigned int res_1; /* 0x0000000C */ ++ /* ++ * I2C RUN Control Register ++ * This register enables and disables the I2C peripheral. Before ++ * enabling, the I2C has to be configured properly. After enabling ++ * no configuration is possible ++ */ ++ unsigned int run_ctrl; /* 0x00000010 */ ++ /* ++ * I2C End Data Control Register ++ * This register is used to either turn around the data transmission ++ * direction or to address another slave without sending a stop ++ * condition. Also the software can stop the slave-transmitter by ++ * sending a not-accolade when working as master-receiver or even ++ * stop data transmission immediately when operating as ++ * master-transmitter. The writing to the bits of this control ++ * register is only effective when in MASTER RECEIVES BYTES, MASTER ++ * TRANSMITS BYTES, MASTER RESTART or SLAVE RECEIVE BYTES state ++ */ ++ unsigned int endd_ctrl; /* 0x00000014 */ ++ /* ++ * I2C Fractional Divider Configuration Register ++ * These register is used to program the fractional divider of the I2C ++ * bus. Before the peripheral is switched on by setting the RUN-bit the ++ * two (fixed) values for the two operating frequencies are programmed ++ * into these (configuration) registers. The Register FDIV_HIGH_CFG has ++ * the same layout as I2C_FDIV_CFG. ++ */ ++ unsigned int fdiv_cfg; /* 0x00000018 */ ++ /* ++ * I2C Fractional Divider (highspeed mode) Configuration Register ++ * These register is used to program the fractional divider of the I2C ++ * bus. Before the peripheral is switched on by setting the RUN-bit the ++ * two (fixed) values for the two operating frequencies are programmed ++ * into these (configuration) registers. The Register FDIV_CFG has the ++ * same layout as I2C_FDIV_CFG. ++ */ ++ unsigned int fdiv_high_cfg; /* 0x0000001C */ ++ /* I2C Address Configuration Register */ ++ unsigned int addr_cfg; /* 0x00000020 */ ++ /* I2C Bus Status Register ++ * This register gives a status information of the I2C. This additional ++ * information can be used by the software to start proper actions. ++ */ ++ unsigned int bus_stat; /* 0x00000024 */ ++ /* I2C FIFO Configuration Register */ ++ unsigned int fifo_cfg; /* 0x00000028 */ ++ /* I2C Maximum Received Packet Size Register */ ++ unsigned int mrps_ctrl; /* 0x0000002C */ ++ /* I2C Received Packet Size Status Register */ ++ unsigned int rps_stat; /* 0x00000030 */ ++ /* I2C Transmit Packet Size Register */ ++ unsigned int tps_ctrl; /* 0x00000034 */ ++ /* I2C Filled FIFO Stages Status Register */ ++ unsigned int ffs_stat; /* 0x00000038 */ ++ /* Reserved */ ++ unsigned int res_2; /* 0x0000003C */ ++ /* I2C Timing Configuration Register */ ++ unsigned int tim_cfg; /* 0x00000040 */ ++ /* Reserved */ ++ unsigned int res_3[7]; /* 0x00000044 */ ++ /* I2C Error Interrupt Request Source Mask Register */ ++ unsigned int err_irqsm; /* 0x00000060 */ ++ /* I2C Error Interrupt Request Source Status Register */ ++ unsigned int err_irqss; /* 0x00000064 */ ++ /* I2C Error Interrupt Request Source Clear Register */ ++ unsigned int err_irqsc; /* 0x00000068 */ ++ /* Reserved */ ++ unsigned int res_4; /* 0x0000006C */ ++ /* I2C Protocol Interrupt Request Source Mask Register */ ++ unsigned int p_irqsm; /* 0x00000070 */ ++ /* I2C Protocol Interrupt Request Source Status Register */ ++ unsigned int p_irqss; /* 0x00000074 */ ++ /* I2C Protocol Interrupt Request Source Clear Register */ ++ unsigned int p_irqsc; /* 0x00000078 */ ++ /* Reserved */ ++ unsigned int res_5; /* 0x0000007C */ ++ /* I2C Raw Interrupt Status Register */ ++ unsigned int ris; /* 0x00000080 */ ++ /* I2C Interrupt Mask Control Register */ ++ unsigned int imsc; /* 0x00000084 */ ++ /* I2C Masked Interrupt Status Register */ ++ unsigned int mis; /* 0x00000088 */ ++ /* I2C Interrupt Clear Register */ ++ unsigned int icr; /* 0x0000008C */ ++ /* I2C Interrupt Set Register */ ++ unsigned int isr; /* 0x00000090 */ ++ /* I2C DMA Enable Register */ ++ unsigned int dmae; /* 0x00000094 */ ++ /* Reserved */ ++ unsigned int res_6[8154]; /* 0x00000098 */ ++ /* I2C Transmit Data Register */ ++ unsigned int txd; /* 0x00008000 */ ++ /* Reserved */ ++ unsigned int res_7[4095]; /* 0x00008004 */ ++ /* I2C Receive Data Register */ ++ unsigned int rxd; /* 0x0000C000 */ ++ /* Reserved */ ++ unsigned int res_8[4095]; /* 0x0000C004 */ ++}; ++ ++/* ++ * Clock Divider for Normal Run Mode ++ * Max 8-bit divider value. IF RMC is 0 the module is disabled. Note: As long ++ * as the new divider value RMC is not valid, the register returns 0x0000 00xx ++ * on reading. ++ */ ++#define I2C_CLC_RMC_MASK 0x0000FF00 ++/* field offset */ ++#define I2C_CLC_RMC_OFFSET 8 ++ ++/* Fields of "I2C Identification Register" */ ++/* Module ID */ ++#define I2C_ID_ID_MASK 0x0000FF00 ++/* field offset */ ++#define I2C_ID_ID_OFFSET 8 ++/* Revision */ ++#define I2C_ID_REV_MASK 0x000000FF ++/* field offset */ ++#define I2C_ID_REV_OFFSET 0 ++ ++/* Fields of "I2C Interrupt Mask Control Register" */ ++/* Enable */ ++#define I2C_IMSC_BREQ_INT_EN 0x00000008 ++/* Enable */ ++#define I2C_IMSC_LBREQ_INT_EN 0x00000004 ++ ++/* Fields of "I2C Fractional Divider Configuration Register" */ ++/* field offset */ ++#define I2C_FDIV_CFG_INC_OFFSET 16 ++ ++/* Fields of "I2C Interrupt Mask Control Register" */ ++/* Enable */ ++#define I2C_IMSC_I2C_P_INT_EN 0x00000020 ++/* Enable */ ++#define I2C_IMSC_I2C_ERR_INT_EN 0x00000010 ++ ++/* Fields of "I2C Error Interrupt Request Source Status Register" */ ++/* TXF_OFL */ ++#define I2C_ERR_IRQSS_TXF_OFL 0x00000008 ++/* TXF_UFL */ ++#define I2C_ERR_IRQSS_TXF_UFL 0x00000004 ++/* RXF_OFL */ ++#define I2C_ERR_IRQSS_RXF_OFL 0x00000002 ++/* RXF_UFL */ ++#define I2C_ERR_IRQSS_RXF_UFL 0x00000001 ++ ++/* Fields of "I2C Raw Interrupt Status Register" */ ++/* Read: Interrupt occurred. */ ++#define I2C_RIS_I2C_ERR_INT_INTOCC 0x00000010 ++/* Read: Interrupt occurred. */ ++#define I2C_RIS_I2C_P_INT_INTOCC 0x00000020 ++ ++/* Fields of "I2C FIFO Configuration Register" */ ++/* TX FIFO Flow Control */ ++#define I2C_FIFO_CFG_TXFC 0x00020000 ++/* RX FIFO Flow Control */ ++#define I2C_FIFO_CFG_RXFC 0x00010000 ++/* Word aligned (character alignment of four characters) */ ++#define I2C_FIFO_CFG_TXFA_TXFA2 0x00002000 ++/* Word aligned (character alignment of four characters) */ ++#define I2C_FIFO_CFG_RXFA_RXFA2 0x00000200 ++/* 1 word */ ++#define I2C_FIFO_CFG_TXBS_TXBS0 0x00000000 ++ ++/* Fields of "I2C FIFO Configuration Register" */ ++/* 1 word */ ++#define I2C_FIFO_CFG_RXBS_RXBS0 0x00000000 ++/* Stop on Packet End Enable */ ++#define I2C_ADDR_CFG_SOPE_EN 0x00200000 ++/* Stop on Not Acknowledge Enable */ ++#define I2C_ADDR_CFG_SONA_EN 0x00100000 ++/* Enable */ ++#define I2C_ADDR_CFG_MnS_EN 0x00080000 ++ ++/* Fields of "I2C Interrupt Clear Register" */ ++/* Clear */ ++#define I2C_ICR_BREQ_INT_CLR 0x00000008 ++/* Clear */ ++#define I2C_ICR_LBREQ_INT_CLR 0x00000004 ++ ++/* Fields of "I2C Fractional Divider Configuration Register" */ ++/* field offset */ ++#define I2C_FDIV_CFG_DEC_OFFSET 0 ++ ++/* Fields of "I2C Bus Status Register" */ ++/* Bus Status */ ++#define I2C_BUS_STAT_BS_MASK 0x00000003 ++/* Read from I2C Bus. */ ++#define I2C_BUS_STAT_RNW_READ 0x00000004 ++/* I2C Bus is free. */ ++#define I2C_BUS_STAT_BS_FREE 0x00000000 ++/* ++ * The device is working as master and has claimed the control on the ++ * I2C-bus (busy master). ++ */ ++#define I2C_BUS_STAT_BS_BM 0x00000002 ++ ++/* Fields of "I2C RUN Control Register" */ ++/* Enable */ ++#define I2C_RUN_CTRL_RUN_EN 0x00000001 ++ ++/* Fields of "I2C End Data Control Register" */ ++/* ++ * Set End of Transmission ++ * Note:Do not write '1' to this bit when bus is free. This will cause an ++ * abort after the first byte when a new transfer is started. ++ */ ++#define I2C_ENDD_CTRL_SETEND 0x00000002 ++ ++/* Fields of "I2C Protocol Interrupt Request Source Status Register" */ ++/* NACK */ ++#define I2C_P_IRQSS_NACK 0x00000010 ++/* AL */ ++#define I2C_P_IRQSS_AL 0x00000008 ++/* RX */ ++#define I2C_P_IRQSS_RX 0x00000040 ++/* TX_END */ ++#define I2C_P_IRQSS_TX_END 0x00000020 ++ ++ ++#endif /* I2C_LANTIQ_H */ diff --git a/target/linux/lantiq/patches-4.19/0035-owrt-lantiq-wifi-and-ethernet-eeprom-handling.patch b/target/linux/lantiq/patches-4.19/0035-owrt-lantiq-wifi-and-ethernet-eeprom-handling.patch new file mode 100644 index 0000000000..2e0ce468f0 --- /dev/null +++ b/target/linux/lantiq/patches-4.19/0035-owrt-lantiq-wifi-and-ethernet-eeprom-handling.patch @@ -0,0 +1,218 @@ +From f8c5db89e793a4bc6c1e87bd7b3a5cec16b75bc3 Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Wed, 10 Sep 2014 22:42:14 +0200 +Subject: [PATCH 35/36] owrt: lantiq: wifi and ethernet eeprom handling + +Signed-off-by: John Crispin +--- + .../mips/include/asm/mach-lantiq/xway/lantiq_soc.h | 3 + + arch/mips/lantiq/xway/Makefile | 3 + + arch/mips/lantiq/xway/ath5k_eep.c | 136 +++++++++++++++++++++ + arch/mips/lantiq/xway/eth_mac.c | 25 ++++ + drivers/net/ethernet/lantiq_etop.c | 6 +- + 5 files changed, 172 insertions(+), 1 deletion(-) + create mode 100644 arch/mips/lantiq/xway/ath5k_eep.c + create mode 100644 arch/mips/lantiq/xway/eth_mac.c + +--- a/arch/mips/include/asm/mach-lantiq/xway/lantiq_soc.h ++++ b/arch/mips/include/asm/mach-lantiq/xway/lantiq_soc.h +@@ -104,5 +104,8 @@ int xrx200_gphy_boot(struct device *dev, + extern void ltq_pmu_enable(unsigned int module); + extern void ltq_pmu_disable(unsigned int module); + ++/* allow the ethernet driver to load a flash mapped mac addr */ ++const u8* ltq_get_eth_mac(void); ++ + #endif /* CONFIG_SOC_TYPE_XWAY */ + #endif /* _LTQ_XWAY_H__ */ +--- a/arch/mips/lantiq/xway/Makefile ++++ b/arch/mips/lantiq/xway/Makefile +@@ -7,3 +7,6 @@ obj-y += timer.o + endif + + obj-y += vmmc.o ++ ++obj-y += eth_mac.o ++obj-$(CONFIG_PCI) += ath5k_eep.o +--- /dev/null ++++ b/arch/mips/lantiq/xway/ath5k_eep.c +@@ -0,0 +1,136 @@ ++/* ++ * Copyright (C) 2011 Luca Olivetti ++ * Copyright (C) 2011 John Crispin ++ * Copyright (C) 2011 Andrej Vlašić ++ * Copyright (C) 2013 Álvaro Fernández Rojas ++ * Copyright (C) 2013 Daniel Gimpelevich ++ * Copyright (C) 2015 Vittorio Gambaletta ++ * ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms of the GNU General Public License version 2 as published ++ * by the Free Software Foundation. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++extern int (*ltq_pci_plat_dev_init)(struct pci_dev *dev); ++struct ath5k_platform_data ath5k_pdata; ++static u8 athxk_eeprom_mac[6]; ++ ++static int ath5k_pci_plat_dev_init(struct pci_dev *dev) ++{ ++ dev->dev.platform_data = &ath5k_pdata; ++ return 0; ++} ++ ++static int ath5k_eep_load; ++int __init of_ath5k_eeprom_probe(struct platform_device *pdev) ++{ ++ struct device_node *np = pdev->dev.of_node, *mtd_np = NULL; ++ int mac_offset; ++ u32 mac_inc = 0; ++ int i; ++ struct mtd_info *the_mtd; ++ size_t flash_readlen; ++ const __be32 *list; ++ const char *part; ++ phandle phandle; ++ ++ list = of_get_property(np, "ath,eep-flash", &i); ++ if (!list || (i != (2 * sizeof(*list)))) ++ return -ENODEV; ++ ++ phandle = be32_to_cpup(list++); ++ if (phandle) ++ mtd_np = of_find_node_by_phandle(phandle); ++ ++ if (!mtd_np) ++ return -ENODEV; ++ ++ part = of_get_property(mtd_np, "label", NULL); ++ if (!part) ++ part = mtd_np->name; ++ ++ the_mtd = get_mtd_device_nm(part); ++ if (IS_ERR(the_mtd)) ++ return -ENODEV; ++ ++ ath5k_pdata.eeprom_data = kmalloc(ATH5K_PLAT_EEP_MAX_WORDS<<1, GFP_KERNEL); ++ ++ i = mtd_read(the_mtd, be32_to_cpup(list), ATH5K_PLAT_EEP_MAX_WORDS << 1, ++ &flash_readlen, (void *) ath5k_pdata.eeprom_data); ++ ++ if (!of_property_read_u32(np, "ath,mac-offset", &mac_offset)) { ++ size_t mac_readlen; ++ mtd_read(the_mtd, mac_offset, 6, &mac_readlen, ++ (void *) athxk_eeprom_mac); ++ } ++ put_mtd_device(the_mtd); ++ ++ if (((ATH5K_PLAT_EEP_MAX_WORDS<<1) != flash_readlen) || i) { ++ dev_err(&pdev->dev, "failed to load eeprom from mtd\n"); ++ return -ENODEV; ++ } ++ ++ if (of_find_property(np, "ath,eep-swap", NULL)) ++ for (i = 0; i < ATH5K_PLAT_EEP_MAX_WORDS; i++) ++ ath5k_pdata.eeprom_data[i] = swab16(ath5k_pdata.eeprom_data[i]); ++ ++ if (!is_valid_ether_addr(athxk_eeprom_mac) && ltq_get_eth_mac()) ++ ether_addr_copy(athxk_eeprom_mac, ltq_get_eth_mac()); ++ ++ if (!is_valid_ether_addr(athxk_eeprom_mac)) { ++ dev_warn(&pdev->dev, "using random mac\n"); ++ random_ether_addr(athxk_eeprom_mac); ++ } ++ ++ if (!of_property_read_u32(np, "ath,mac-increment", &mac_inc)) ++ athxk_eeprom_mac[5] += mac_inc; ++ ++ ath5k_pdata.macaddr = athxk_eeprom_mac; ++ ltq_pci_plat_dev_init = ath5k_pci_plat_dev_init; ++ ++ dev_info(&pdev->dev, "loaded ath5k eeprom\n"); ++ ++ return 0; ++} ++ ++static struct of_device_id ath5k_eeprom_ids[] = { ++ { .compatible = "ath5k,eeprom" }, ++ { } ++}; ++ ++static struct platform_driver ath5k_eeprom_driver = { ++ .driver = { ++ .name = "ath5k,eeprom", ++ .owner = THIS_MODULE, ++ .of_match_table = of_match_ptr(ath5k_eeprom_ids), ++ }, ++}; ++ ++static int __init of_ath5k_eeprom_init(void) ++{ ++ int ret = platform_driver_probe(&ath5k_eeprom_driver, of_ath5k_eeprom_probe); ++ ++ if (ret) ++ ath5k_eep_load = 1; ++ ++ return ret; ++} ++ ++static int __init of_ath5k_eeprom_init_late(void) ++{ ++ if (!ath5k_eep_load) ++ return 0; ++ ++ return platform_driver_probe(&ath5k_eeprom_driver, of_ath5k_eeprom_probe); ++} ++late_initcall(of_ath5k_eeprom_init_late); ++subsys_initcall(of_ath5k_eeprom_init); +--- /dev/null ++++ b/arch/mips/lantiq/xway/eth_mac.c +@@ -0,0 +1,25 @@ ++/* ++ * Copyright (C) 2012 John Crispin ++ * ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms of the GNU General Public License version 2 as published ++ * by the Free Software Foundation. ++ */ ++ ++#include ++#include ++ ++static u8 eth_mac[6]; ++static int eth_mac_set; ++ ++const u8* ltq_get_eth_mac(void) ++{ ++ return eth_mac; ++} ++ ++static int __init setup_ethaddr(char *str) ++{ ++ eth_mac_set = mac_pton(str, eth_mac); ++ return !eth_mac_set; ++} ++early_param("ethaddr", setup_ethaddr); +--- a/drivers/net/ethernet/lantiq_etop.c ++++ b/drivers/net/ethernet/lantiq_etop.c +@@ -783,7 +783,11 @@ ltq_etop_init(struct net_device *dev) + if (err) + goto err_hw; + +- memcpy(&mac, &priv->pldata->mac, sizeof(struct sockaddr)); ++ memcpy(&mac.sa_data, ltq_get_eth_mac(), ETH_ALEN); ++ ++ if (priv->mac && !is_valid_ether_addr(mac.sa_data)) ++ memcpy(&mac.sa_data, priv->mac, ETH_ALEN); ++ + if (!is_valid_ether_addr(mac.sa_data)) { + pr_warn("etop: invalid MAC, using random\n"); + eth_random_addr(mac.sa_data); diff --git a/target/linux/lantiq/patches-4.19/0042-arch-mips-increase-io_space_limit.patch b/target/linux/lantiq/patches-4.19/0042-arch-mips-increase-io_space_limit.patch new file mode 100644 index 0000000000..14b417e690 --- /dev/null +++ b/target/linux/lantiq/patches-4.19/0042-arch-mips-increase-io_space_limit.patch @@ -0,0 +1,23 @@ +From 9807eb80a1b3bad7a4a89aa6566497bb1cadd6ef Mon Sep 17 00:00:00 2001 +From: John Crispin +Date: Fri, 3 Jun 2016 13:12:20 +0200 +Subject: [PATCH] arch: mips: increase io_space_limit + +this value comes from x86 and breaks some pci devices + +Signed-off-by: John Crispin +--- + arch/mips/include/asm/io.h | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/arch/mips/include/asm/io.h ++++ b/arch/mips/include/asm/io.h +@@ -50,7 +50,7 @@ + + /* ioswab[bwlq], __mem_ioswab[bwlq] are defined in mangle-port.h */ + +-#define IO_SPACE_LIMIT 0xffff ++#define IO_SPACE_LIMIT 0xffffffff + + /* + * On MIPS I/O ports are memory mapped, so we access them using normal diff --git a/target/linux/lantiq/patches-4.19/0050-USB-DWC2-make-the-lantiq-settings-match-vendor-drive.patch b/target/linux/lantiq/patches-4.19/0050-USB-DWC2-make-the-lantiq-settings-match-vendor-drive.patch new file mode 100644 index 0000000000..37894244e5 --- /dev/null +++ b/target/linux/lantiq/patches-4.19/0050-USB-DWC2-make-the-lantiq-settings-match-vendor-drive.patch @@ -0,0 +1,78 @@ +From de2cad82c4d0872066f83ce59462603852b47f03 Mon Sep 17 00:00:00 2001 +From: Hauke Mehrtens +Date: Fri, 6 Jan 2017 17:55:24 +0100 +Subject: [PATCH 2/2] usb: dwc2: add support for other Lantiq SoCs + +The size of the internal RAM of the DesignWare USB controller changed +between the different Lantiq SoCs. We have the following sizes: + +Amazon + Danube: 8 KByte +Amazon SE + arx100: 2 KByte +xrx200 + xrx300: 2.5 KByte + +For Danube SoC we do not provide the params and let the driver decide +to use sane defaults, for the Amazon SE and arx100 we use small fifos +and for the xrx200 and xrx300 SCs a little bit bigger periodic fifo. +The auto detection of max_transfer_size and max_packet_count should +work, so remove it. + +Signed-off-by: Hauke Mehrtens +--- + drivers/usb/dwc2/platform.c | 46 ++++++++++++++++++++++++++++++++++++++------- + 1 file changed, 39 insertions(+), 7 deletions(-) + +--- a/drivers/usb/dwc2/params.c ++++ b/drivers/usb/dwc2/params.c +@@ -83,7 +83,14 @@ static void dwc2_set_rk_params(struct dw + GAHBCFG_HBSTLEN_SHIFT; + } + +-static void dwc2_set_ltq_params(struct dwc2_hsotg *hsotg) ++static void dwc2_set_ltq_danube_params(struct dwc2_hsotg *hsotg) ++{ ++ struct dwc2_core_params *p = &hsotg->params; ++ ++ p->otg_cap = DWC2_CAP_PARAM_NO_HNP_SRP_CAPABLE; ++} ++ ++static void dwc2_set_ltq_ase_params(struct dwc2_hsotg *hsotg) + { + struct dwc2_core_params *p = &hsotg->params; + +@@ -91,12 +98,20 @@ static void dwc2_set_ltq_params(struct d + p->host_rx_fifo_size = 288; + p->host_nperio_tx_fifo_size = 128; + p->host_perio_tx_fifo_size = 96; +- p->max_transfer_size = 65535; +- p->max_packet_count = 511; + p->ahbcfg = GAHBCFG_HBSTLEN_INCR16 << + GAHBCFG_HBSTLEN_SHIFT; + } + ++static void dwc2_set_ltq_xrx200_params(struct dwc2_hsotg *hsotg) ++{ ++ struct dwc2_core_params *p = &hsotg->params; ++ ++ p->otg_cap = DWC2_CAP_PARAM_NO_HNP_SRP_CAPABLE; ++ p->host_rx_fifo_size = 288; ++ p->host_nperio_tx_fifo_size = 128; ++ p->host_perio_tx_fifo_size = 136; ++} ++ + static void dwc2_set_amlogic_params(struct dwc2_hsotg *hsotg) + { + struct dwc2_core_params *p = &hsotg->params; +@@ -140,8 +155,11 @@ const struct of_device_id dwc2_of_match_ + { .compatible = "brcm,bcm2835-usb", .data = dwc2_set_bcm_params }, + { .compatible = "hisilicon,hi6220-usb", .data = dwc2_set_his_params }, + { .compatible = "rockchip,rk3066-usb", .data = dwc2_set_rk_params }, +- { .compatible = "lantiq,arx100-usb", .data = dwc2_set_ltq_params }, +- { .compatible = "lantiq,xrx200-usb", .data = dwc2_set_ltq_params }, ++ { .compatible = "lantiq,danube-usb", .data = &dwc2_set_ltq_danube_params }, ++ { .compatible = "lantiq,ase-usb", .data = &dwc2_set_ltq_ase_params }, ++ { .compatible = "lantiq,arx100-usb", .data = &dwc2_set_ltq_ase_params }, ++ { .compatible = "lantiq,xrx200-usb", .data = &dwc2_set_ltq_xrx200_params }, ++ { .compatible = "lantiq,xrx300-usb", .data = &dwc2_set_ltq_xrx200_params }, + { .compatible = "snps,dwc2" }, + { .compatible = "samsung,s3c6400-hsotg" }, + { .compatible = "amlogic,meson8-usb", diff --git a/target/linux/lantiq/patches-4.19/0051-MIPS-lantiq-improve-USB-initialization.patch b/target/linux/lantiq/patches-4.19/0051-MIPS-lantiq-improve-USB-initialization.patch new file mode 100644 index 0000000000..5030bbf3dd --- /dev/null +++ b/target/linux/lantiq/patches-4.19/0051-MIPS-lantiq-improve-USB-initialization.patch @@ -0,0 +1,49 @@ +From 14909c4e4e836925668e74fc6e0e85ba0283cbf9 Mon Sep 17 00:00:00 2001 +From: Hauke Mehrtens +Date: Fri, 6 Jan 2017 17:40:12 +0100 +Subject: [PATCH 2/2] MIPS: lantiq: improve USB initialization + +This adds code to initialize the USB controller and PHY also on Danube, +Amazon SE and AR10. This code is based on the Vendor driver from +different UGW versions and compared to the hardware documentation. + +Signed-off-by: Hauke Mehrtens +--- + arch/mips/lantiq/xway/sysctrl.c | 20 +++++++ + 2 files changed, 110 insertions(+), 30 deletions(-) + + +--- a/arch/mips/lantiq/xway/sysctrl.c ++++ b/arch/mips/lantiq/xway/sysctrl.c +@@ -246,6 +246,25 @@ static void pmu_disable(struct clk *clk) + pr_warn("deactivating PMU module failed!"); + } + ++static void usb_set_clock(void) ++{ ++ unsigned int val = ltq_cgu_r32(ifccr); ++ ++ if (of_machine_is_compatible("lantiq,ar10") || ++ of_machine_is_compatible("lantiq,grx390")) { ++ val &= ~0x03; /* XTAL divided by 3 */ ++ } else if (of_machine_is_compatible("lantiq,ar9") || ++ of_machine_is_compatible("lantiq,vr9")) { ++ /* TODO: this depends on the XTAL frequency */ ++ val |= 0x03; /* XTAL divided by 3 */ ++ } else if (of_machine_is_compatible("lantiq,ase")) { ++ val |= 0x20; /* from XTAL */ ++ } else if (of_machine_is_compatible("lantiq,danube")) { ++ val |= 0x30; /* 12 MHz, generated from 36 MHz */ ++ } ++ ltq_cgu_w32(val, ifccr); ++} ++ + /* the pci enable helper */ + static int pci_enable(struct clk *clk) + { +@@ -569,4 +588,5 @@ void __init ltq_soc_init(void) + clkdev_add_pmu("1e116000.mei", "dfe", 1, 0, PMU_DFE); + clkdev_add_pmu("1e100400.serial", NULL, 1, 0, PMU_ASC0); + } ++ usb_set_clock(); + } diff --git a/target/linux/lantiq/patches-4.19/0101-find_active_root.patch b/target/linux/lantiq/patches-4.19/0101-find_active_root.patch new file mode 100644 index 0000000000..73361c87fa --- /dev/null +++ b/target/linux/lantiq/patches-4.19/0101-find_active_root.patch @@ -0,0 +1,93 @@ +--- a/drivers/mtd/ofpart.c ++++ b/drivers/mtd/ofpart.c +@@ -25,6 +25,38 @@ static bool node_has_compatible(struct d + return of_get_property(pp, "compatible", NULL); + } + ++static uint8_t * brnboot_get_selected_root_part(struct mtd_info *master, ++ loff_t offset) ++{ ++ static uint8_t root_id; ++ int err, len; ++ ++ err = mtd_read(master, offset, 0x01, &len, &root_id); ++ ++ if (mtd_is_bitflip(err) || !err) ++ return &root_id; ++ ++ return NULL; ++} ++ ++static void brnboot_set_active_root_part(struct mtd_partition *pparts, ++ struct device_node **part_nodes, ++ int nr_parts, ++ uint8_t *root_id) ++{ ++ int i; ++ ++ for (i = 0; i < nr_parts; i++) { ++ int part_root_id; ++ ++ if (!of_property_read_u32(part_nodes[i], "brnboot,root-id", &part_root_id) ++ && part_root_id == *root_id) { ++ pparts[i].name = "firmware"; ++ break; ++ } ++ } ++} ++ + static int parse_fixed_partitions(struct mtd_info *master, + const struct mtd_partition **pparts, + struct mtd_part_parser_data *data) +@@ -36,7 +68,8 @@ static int parse_fixed_partitions(struct + struct device_node *pp; + int nr_parts, i, ret = 0; + bool dedicated = true; +- ++ uint8_t *proot_id = NULL; ++ struct device_node **part_nodes; + + /* Pull of_node from the master device node */ + mtd_node = mtd_get_of_node(master); +@@ -72,7 +105,9 @@ static int parse_fixed_partitions(struct + return 0; + + parts = kzalloc(nr_parts * sizeof(*parts), GFP_KERNEL); +- if (!parts) ++ part_nodes = kzalloc(nr_parts * sizeof(*part_nodes), GFP_KERNEL); ++ ++ if (!parts || !part_nodes) + return -ENOMEM; + + i = 0; +@@ -121,12 +156,22 @@ static int parse_fixed_partitions(struct + if (of_get_property(pp, "lock", &len)) + parts[i].mask_flags |= MTD_POWERUP_LOCK; + ++ if (!proot_id && of_device_is_compatible(pp, "brnboot,root-selector")) ++ proot_id = brnboot_get_selected_root_part(master, parts[i].offset); ++ ++ part_nodes[i] = pp; ++ + i++; + } + + if (!nr_parts) + goto ofpart_none; + ++ if (proot_id) ++ brnboot_set_active_root_part(parts, part_nodes, nr_parts, proot_id); ++ ++ kfree(part_nodes); ++ + *pparts = parts; + return nr_parts; + +@@ -137,6 +182,7 @@ ofpart_fail: + ofpart_none: + of_node_put(pp); + kfree(parts); ++ kfree(part_nodes); + return ret; + } + diff --git a/target/linux/lantiq/patches-4.19/0151-lantiq-ifxmips_pcie-use-of.patch b/target/linux/lantiq/patches-4.19/0151-lantiq-ifxmips_pcie-use-of.patch new file mode 100644 index 0000000000..03d43c241f --- /dev/null +++ b/target/linux/lantiq/patches-4.19/0151-lantiq-ifxmips_pcie-use-of.patch @@ -0,0 +1,166 @@ +--- a/arch/mips/pci/ifxmips_pcie.c ++++ b/arch/mips/pci/ifxmips_pcie.c +@@ -18,6 +18,9 @@ + #include + #include + ++#include ++#include ++ + #include "ifxmips_pcie.h" + #include "ifxmips_pcie_reg.h" + +@@ -40,6 +43,7 @@ + static DEFINE_SPINLOCK(ifx_pcie_lock); + + u32 g_pcie_debug_flag = PCIE_MSG_ANY & (~PCIE_MSG_CFG); ++static int pcie_reset_gpio; + + static ifx_pcie_irq_t pcie_irqs[IFX_PCIE_CORE_NR] = { + { +@@ -82,6 +86,22 @@ void ifx_pcie_debug(const char *fmt, ... + printk("%s", buf); + } + ++static inline void pcie_ep_gpio_rst_init(int pcie_port) ++{ ++ gpio_direction_output(pcie_reset_gpio, 1); ++ gpio_set_value(pcie_reset_gpio, 1); ++} ++ ++static inline void pcie_device_rst_assert(int pcie_port) ++{ ++ gpio_set_value(pcie_reset_gpio, 0); ++} ++ ++static inline void pcie_device_rst_deassert(int pcie_port) ++{ ++ mdelay(100); ++ gpio_direction_output(pcie_reset_gpio, 1); ++} + + static inline int pcie_ltssm_enable(int pcie_port) + { +@@ -1045,8 +1065,9 @@ pcie_rc_initialize(int pcie_port) + return 0; + } + +-static int __init ifx_pcie_bios_init(void) ++static int ifx_pcie_bios_probe(struct platform_device *pdev) + { ++ struct device_node *node = pdev->dev.of_node; + void __iomem *io_map_base; + int pcie_port; + int startup_port; +@@ -1055,7 +1076,17 @@ static int __init ifx_pcie_bios_init(voi + pcie_ahb_pmu_setup(); + + startup_port = IFX_PCIE_PORT0; +- ++ ++ pcie_reset_gpio = of_get_named_gpio(node, "gpio-reset", 0); ++ if (gpio_is_valid(pcie_reset_gpio)) { ++ int ret = devm_gpio_request(&pdev->dev, pcie_reset_gpio, "pcie-reset"); ++ if (ret) { ++ dev_err(&pdev->dev, "failed to request gpio %d\n", pcie_reset_gpio); ++ return ret; ++ } ++ gpio_direction_output(pcie_reset_gpio, 1); ++ } ++ + for (pcie_port = startup_port; pcie_port < IFX_PCIE_CORE_NR; pcie_port++){ + if (pcie_rc_initialize(pcie_port) == 0) { + IFX_PCIE_PRINT(PCIE_MSG_INIT, "%s: ifx_pcie_cfg_base 0x%p\n", +@@ -1067,6 +1098,7 @@ static int __init ifx_pcie_bios_init(voi + return -ENOMEM; + } + ifx_pcie_controller[pcie_port].pcic.io_map_base = (unsigned long)io_map_base; ++ pci_load_of_ranges(&ifx_pcie_controller[pcie_port].pcic, node); + + register_pci_controller(&ifx_pcie_controller[pcie_port].pcic); + /* XXX, clear error status */ +@@ -1083,6 +1115,30 @@ static int __init ifx_pcie_bios_init(voi + + return 0; + } ++ ++static const struct of_device_id ifxmips_pcie_match[] = { ++ { .compatible = "lantiq,pcie-xrx200" }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, ifxmips_pcie_match); ++ ++static struct platform_driver ltq_pci_driver = { ++ .probe = ifx_pcie_bios_probe, ++ .driver = { ++ .name = "pcie-xrx200", ++ .owner = THIS_MODULE, ++ .of_match_table = ifxmips_pcie_match, ++ }, ++}; ++ ++int __init ifx_pcie_bios_init(void) ++{ ++ int ret = platform_driver_register(<q_pci_driver); ++ if (ret) ++ pr_info("pcie-xrx200: Error registering platform driver!"); ++ return ret; ++} ++ + arch_initcall(ifx_pcie_bios_init); + + MODULE_LICENSE("GPL"); +--- a/arch/mips/pci/ifxmips_pcie_vr9.h ++++ b/arch/mips/pci/ifxmips_pcie_vr9.h +@@ -22,8 +22,6 @@ + #include + #include + +-#define IFX_PCIE_GPIO_RESET 494 +- + #define IFX_REG_R32 ltq_r32 + #define IFX_REG_W32 ltq_w32 + #define CONFIG_IFX_PCIE_HW_SWAP +@@ -53,21 +51,6 @@ + #define OUT ((volatile u32*)(IFX_GPIO + 0x0070)) + + +-static inline void pcie_ep_gpio_rst_init(int pcie_port) +-{ +- +- gpio_request(IFX_PCIE_GPIO_RESET, "pcie-reset"); +- gpio_direction_output(IFX_PCIE_GPIO_RESET, 1); +- gpio_set_value(IFX_PCIE_GPIO_RESET, 1); +- +-/* ifx_gpio_pin_reserve(IFX_PCIE_GPIO_RESET, ifx_pcie_gpio_module_id); +- ifx_gpio_output_set(IFX_PCIE_GPIO_RESET, ifx_pcie_gpio_module_id); +- ifx_gpio_dir_out_set(IFX_PCIE_GPIO_RESET, ifx_pcie_gpio_module_id); +- ifx_gpio_altsel0_clear(IFX_PCIE_GPIO_RESET, ifx_pcie_gpio_module_id); +- ifx_gpio_altsel1_clear(IFX_PCIE_GPIO_RESET, ifx_pcie_gpio_module_id); +- ifx_gpio_open_drain_set(IFX_PCIE_GPIO_RESET, ifx_pcie_gpio_module_id);*/ +-} +- + static inline void pcie_ahb_pmu_setup(void) + { + /* Enable AHB bus master/slave */ +@@ -180,20 +163,6 @@ static inline void pcie_phy_rst_deassert + IFX_REG_W32(reg, IFX_RCU_RST_REQ); + } + +-static inline void pcie_device_rst_assert(int pcie_port) +-{ +- gpio_set_value(IFX_PCIE_GPIO_RESET, 0); +-// ifx_gpio_output_clear(IFX_PCIE_GPIO_RESET, ifx_pcie_gpio_module_id); +-} +- +-static inline void pcie_device_rst_deassert(int pcie_port) +-{ +- mdelay(100); +- gpio_direction_output(IFX_PCIE_GPIO_RESET, 1); +-// gpio_set_value(IFX_PCIE_GPIO_RESET, 1); +- //ifx_gpio_output_set(IFX_PCIE_GPIO_RESET, ifx_pcie_gpio_module_id); +-} +- + static inline void pcie_core_pmu_setup(int pcie_port) + { + struct clk *clk; diff --git a/target/linux/lantiq/patches-4.19/0152-lantiq-VPE.patch b/target/linux/lantiq/patches-4.19/0152-lantiq-VPE.patch new file mode 100644 index 0000000000..b0b5bd3a57 --- /dev/null +++ b/target/linux/lantiq/patches-4.19/0152-lantiq-VPE.patch @@ -0,0 +1,180 @@ +--- a/arch/mips/Kconfig ++++ b/arch/mips/Kconfig +@@ -2327,6 +2327,12 @@ config MIPS_VPE_LOADER + Includes a loader for loading an elf relocatable object + onto another VPE and running it. + ++config IFX_VPE_EXT ++ bool "IFX APRP Extensions" ++ depends on MIPS_VPE_LOADER ++ help ++ IFX included extensions in APRP ++ + config MIPS_VPE_LOADER_CMP + bool + default "y" +--- a/arch/mips/include/asm/vpe.h ++++ b/arch/mips/include/asm/vpe.h +@@ -127,4 +127,13 @@ void cleanup_tc(struct tc *tc); + + int __init vpe_module_init(void); + void __exit vpe_module_exit(void); ++ ++/* For the explanation of the APIs please refer the section "MT APRP Kernel ++ * Programming" in AR9 SW Architecture Specification ++ */ ++int32_t vpe1_sw_start(void *sw_start_addr, uint32_t tcmask, uint32_t flags); ++int32_t vpe1_sw_stop(uint32_t flags); ++uint32_t vpe1_get_load_addr(uint32_t flags); ++uint32_t vpe1_get_max_mem(uint32_t flags); ++ + #endif /* _ASM_VPE_H */ +--- a/arch/mips/kernel/vpe-mt.c ++++ b/arch/mips/kernel/vpe-mt.c +@@ -29,6 +29,7 @@ int vpe_run(struct vpe *v) + struct vpe_notifications *notifier; + unsigned int vpeflags; + struct tc *t; ++ unsigned long physical_memsize = 0L; + + /* check we are the Master VPE */ + local_irq_save(flags); +@@ -417,6 +418,8 @@ int __init vpe_module_init(void) + } + + v->ntcs = hw_tcs - aprp_cpu_index(); ++ write_tc_c0_tcbind((read_tc_c0_tcbind() & ++ ~TCBIND_CURVPE) | 1); + + /* add the tc to the list of this vpe's tc's. */ + list_add(&t->tc, &v->tc); +@@ -519,3 +522,47 @@ void __exit vpe_module_exit(void) + release_vpe(v); + } + } ++ ++#ifdef CONFIG_IFX_VPE_EXT ++int32_t vpe1_sw_start(void *sw_start_addr, uint32_t tcmask, uint32_t flags) ++{ ++ enum vpe_state state; ++ struct vpe *v = get_vpe(tclimit); ++ struct vpe_notifications *not; ++ ++ if (tcmask || flags) { ++ pr_warn("Currently tcmask and flags should be 0. Other values are not supported\n"); ++ return -1; ++ } ++ ++ state = xchg(&v->state, VPE_STATE_INUSE); ++ if (state != VPE_STATE_UNUSED) { ++ vpe_stop(v); ++ ++ list_for_each_entry(not, &v->notify, list) { ++ not->stop(tclimit); ++ } ++ } ++ ++ v->__start = (unsigned long)sw_start_addr; ++ ++ if (!vpe_run(v)) { ++ pr_debug("VPE loader: VPE1 running successfully\n"); ++ return 0; ++ } ++ return -1; ++} ++EXPORT_SYMBOL(vpe1_sw_start); ++ ++int32_t vpe1_sw_stop(uint32_t flags) ++{ ++ struct vpe *v = get_vpe(tclimit); ++ ++ if (!vpe_free(v)) { ++ pr_debug("RP Stopped\n"); ++ return 0; ++ } else ++ return -1; ++} ++EXPORT_SYMBOL(vpe1_sw_stop); ++#endif +--- a/arch/mips/kernel/vpe.c ++++ b/arch/mips/kernel/vpe.c +@@ -49,6 +49,41 @@ struct vpe_control vpecontrol = { + .tc_list = LIST_HEAD_INIT(vpecontrol.tc_list) + }; + ++#ifdef CONFIG_IFX_VPE_EXT ++unsigned int vpe1_load_addr; ++ ++static int __init load_address(char *str) ++{ ++ get_option(&str, &vpe1_load_addr); ++ return 1; ++} ++__setup("vpe1_load_addr=", load_address); ++ ++static unsigned int vpe1_mem; ++static int __init vpe1mem(char *str) ++{ ++ vpe1_mem = memparse(str, &str); ++ return 1; ++} ++__setup("vpe1_mem=", vpe1mem); ++ ++uint32_t vpe1_get_load_addr(uint32_t flags) ++{ ++ return vpe1_load_addr; ++} ++EXPORT_SYMBOL(vpe1_get_load_addr); ++ ++uint32_t vpe1_get_max_mem(uint32_t flags) ++{ ++ if (!vpe1_mem) ++ return P_SIZE; ++ else ++ return vpe1_mem; ++} ++EXPORT_SYMBOL(vpe1_get_max_mem); ++ ++#endif ++ + /* get the vpe associated with this minor */ + struct vpe *get_vpe(int minor) + { +--- a/arch/mips/lantiq/prom.c ++++ b/arch/mips/lantiq/prom.c +@@ -37,10 +37,14 @@ unsigned long physical_memsize = 0L; + */ + static struct ltq_soc_info soc_info; + ++/* for Multithreading (APRP), vpe.c will use it */ ++unsigned long cp0_memsize; ++ + const char *get_system_type(void) + { + return soc_info.sys_type; + } ++EXPORT_SYMBOL(ltq_soc_type); + + int ltq_soc_type(void) + { +--- a/arch/mips/include/asm/mipsmtregs.h ++++ b/arch/mips/include/asm/mipsmtregs.h +@@ -32,6 +32,9 @@ + #define read_c0_vpeconf1() __read_32bit_c0_register($1, 3) + #define write_c0_vpeconf1(val) __write_32bit_c0_register($1, 3, val) + ++#define read_c0_vpeopt() __read_32bit_c0_register($1, 7) ++#define write_c0_vpeopt(val) __write_32bit_c0_register($1, 7, val) ++ + #define read_c0_tcstatus() __read_32bit_c0_register($2, 1) + #define write_c0_tcstatus(val) __write_32bit_c0_register($2, 1, val) + +@@ -377,6 +380,8 @@ do { \ + #define write_vpe_c0_vpeconf0(val) mttc0(1, 2, val) + #define read_vpe_c0_vpeconf1() mftc0(1, 3) + #define write_vpe_c0_vpeconf1(val) mttc0(1, 3, val) ++#define read_vpe_c0_vpeopt() mftc0(1, 7) ++#define write_vpe_c0_vpeopt(val) mttc0(1, 7, val) + #define read_vpe_c0_count() mftc0(9, 0) + #define write_vpe_c0_count(val) mttc0(9, 0, val) + #define read_vpe_c0_status() mftc0(12, 0) diff --git a/target/linux/lantiq/patches-4.19/0154-lantiq-pci-bar11mask-fix.patch b/target/linux/lantiq/patches-4.19/0154-lantiq-pci-bar11mask-fix.patch new file mode 100644 index 0000000000..d0acd4bb10 --- /dev/null +++ b/target/linux/lantiq/patches-4.19/0154-lantiq-pci-bar11mask-fix.patch @@ -0,0 +1,22 @@ +--- a/arch/mips/pci/pci-lantiq.c ++++ b/arch/mips/pci/pci-lantiq.c +@@ -61,6 +61,8 @@ + #define ltq_pci_cfg_w32(x, y) ltq_w32((x), ltq_pci_mapped_cfg + (y)) + #define ltq_pci_cfg_r32(x) ltq_r32(ltq_pci_mapped_cfg + (x)) + ++extern u32 max_low_pfn; ++ + __iomem void *ltq_pci_mapped_cfg; + static __iomem void *ltq_pci_membase; + +@@ -86,8 +88,8 @@ static inline u32 ltq_calc_bar11mask(voi + u32 mem, bar11mask; + + /* BAR11MASK value depends on available memory on system. */ +- mem = get_num_physpages() * PAGE_SIZE; +- bar11mask = (0x0ffffff0 & ~((1 << (fls(mem) - 1)) - 1)) | 8; ++ mem = max_low_pfn << PAGE_SHIFT; ++ bar11mask = ((-roundup_pow_of_two(mem)) & 0x0F000000) | 8; + + return bar11mask; + } diff --git a/target/linux/lantiq/patches-4.19/0155-lantiq-VPE-nosmp.patch b/target/linux/lantiq/patches-4.19/0155-lantiq-VPE-nosmp.patch new file mode 100644 index 0000000000..898c2d4821 --- /dev/null +++ b/target/linux/lantiq/patches-4.19/0155-lantiq-VPE-nosmp.patch @@ -0,0 +1,14 @@ +--- a/arch/mips/kernel/vpe-mt.c ++++ b/arch/mips/kernel/vpe-mt.c +@@ -132,7 +132,10 @@ int vpe_run(struct vpe *v) + * kernels need to turn it on, even if that wasn't the pre-dvpe() state. + */ + #ifdef CONFIG_SMP +- evpe(vpeflags); ++ if (!setup_max_cpus) /* nosmp is set */ ++ evpe(EVPE_ENABLE); ++ else ++ evpe(vpeflags); + #else + evpe(EVPE_ENABLE); + #endif diff --git a/target/linux/lantiq/patches-4.19/0160-owrt-lantiq-multiple-flash.patch b/target/linux/lantiq/patches-4.19/0160-owrt-lantiq-multiple-flash.patch new file mode 100644 index 0000000000..304ff4bac8 --- /dev/null +++ b/target/linux/lantiq/patches-4.19/0160-owrt-lantiq-multiple-flash.patch @@ -0,0 +1,220 @@ +--- a/drivers/mtd/maps/lantiq-flash.c ++++ b/drivers/mtd/maps/lantiq-flash.c +@@ -19,6 +19,7 @@ + #include + #include + #include ++#include + #include + + #include +@@ -38,13 +39,16 @@ enum { + LTQ_NOR_NORMAL + }; + ++#define MAX_RESOURCES 4 ++ + struct ltq_mtd { +- struct resource *res; +- struct mtd_info *mtd; +- struct map_info *map; ++ struct mtd_info *mtd[MAX_RESOURCES]; ++ struct mtd_info *cmtd; ++ struct map_info map[MAX_RESOURCES]; + }; + + static const char ltq_map_name[] = "ltq_nor"; ++static const char * const ltq_probe_types[] = { "cmdlinepart", "ofpart", NULL }; + + static map_word + ltq_read16(struct map_info *map, unsigned long adr) +@@ -108,11 +112,43 @@ ltq_copy_to(struct map_info *map, unsign + } + + static int ++ltq_mtd_remove(struct platform_device *pdev) ++{ ++ struct ltq_mtd *ltq_mtd = platform_get_drvdata(pdev); ++ int i; ++ ++ if (ltq_mtd == NULL) ++ return 0; ++ ++ if (ltq_mtd->cmtd) { ++ mtd_device_unregister(ltq_mtd->cmtd); ++ if (ltq_mtd->cmtd != ltq_mtd->mtd[0]) ++ mtd_concat_destroy(ltq_mtd->cmtd); ++ } ++ ++ for (i = 0; i < MAX_RESOURCES; i++) { ++ if (ltq_mtd->mtd[i] != NULL) ++ map_destroy(ltq_mtd->mtd[i]); ++ } ++ ++ kfree(ltq_mtd); ++ ++ return 0; ++} ++ ++static int + ltq_mtd_probe(struct platform_device *pdev) + { + struct ltq_mtd *ltq_mtd; + struct cfi_private *cfi; +- int err; ++ int err = 0; ++ int i; ++ int devices_found = 0; ++ ++ static const char *rom_probe_types[] = { ++ "cfi_probe", "jedec_probe", NULL ++ }; ++ const char **type; + + ltq_mtd = devm_kzalloc(&pdev->dev, sizeof(struct ltq_mtd), GFP_KERNEL); + if (!ltq_mtd) +@@ -120,75 +156,89 @@ ltq_mtd_probe(struct platform_device *pd + + platform_set_drvdata(pdev, ltq_mtd); + +- ltq_mtd->res = platform_get_resource(pdev, IORESOURCE_MEM, 0); +- if (!ltq_mtd->res) { +- dev_err(&pdev->dev, "failed to get memory resource\n"); +- return -ENOENT; ++ for (i = 0; i < pdev->num_resources; i++) { ++ printk(KERN_NOTICE "lantiq nor flash device: %.8llx at %.8llx\n", ++ (unsigned long long)resource_size(&pdev->resource[i]), ++ (unsigned long long)pdev->resource[i].start); ++ ++ if (!devm_request_mem_region(&pdev->dev, ++ pdev->resource[i].start, ++ resource_size(&pdev->resource[i]), ++ dev_name(&pdev->dev))) { ++ dev_err(&pdev->dev, "Could not reserve memory region\n"); ++ return -ENOMEM; ++ } ++ ++ ltq_mtd->map[i].name = ltq_map_name; ++ ltq_mtd->map[i].bankwidth = 2; ++ ltq_mtd->map[i].read = ltq_read16; ++ ltq_mtd->map[i].write = ltq_write16; ++ ltq_mtd->map[i].copy_from = ltq_copy_from; ++ ltq_mtd->map[i].copy_to = ltq_copy_to; ++ ++ if (of_find_property(pdev->dev.of_node, "lantiq,noxip", NULL)) ++ ltq_mtd->map[i].phys = NO_XIP; ++ else ++ ltq_mtd->map[i].phys = pdev->resource[i].start; ++ ltq_mtd->map[i].size = resource_size(&pdev->resource[i]); ++ ltq_mtd->map[i].virt = devm_ioremap(&pdev->dev, pdev->resource[i].start, ++ ltq_mtd->map[i].size); ++ if (IS_ERR(ltq_mtd->map[i].virt)) ++ return PTR_ERR(ltq_mtd->map[i].virt); ++ ++ if (ltq_mtd->map[i].virt == NULL) { ++ dev_err(&pdev->dev, "Failed to ioremap flash region\n"); ++ err = PTR_ERR(ltq_mtd->map[i].virt); ++ goto err_out; ++ } ++ ++ ltq_mtd->map[i].map_priv_1 = LTQ_NOR_PROBING; ++ for (type = rom_probe_types; !ltq_mtd->mtd[i] && *type; type++) ++ ltq_mtd->mtd[i] = do_map_probe(*type, <q_mtd->map[i]); ++ ltq_mtd->map[i].map_priv_1 = LTQ_NOR_NORMAL; ++ ++ if (!ltq_mtd->mtd[i]) { ++ dev_err(&pdev->dev, "probing failed\n"); ++ return -ENXIO; ++ } else { ++ devices_found++; ++ } ++ ++ ltq_mtd->mtd[i]->owner = THIS_MODULE; ++ ltq_mtd->mtd[i]->dev.parent = &pdev->dev; ++ ++ cfi = ltq_mtd->map[i].fldrv_priv; ++ cfi->addr_unlock1 ^= 1; ++ cfi->addr_unlock2 ^= 1; + } + +- ltq_mtd->map = devm_kzalloc(&pdev->dev, sizeof(struct map_info), +- GFP_KERNEL); +- if (!ltq_mtd->map) +- return -ENOMEM; +- +- if (of_find_property(pdev->dev.of_node, "lantiq,noxip", NULL)) +- ltq_mtd->map->phys = NO_XIP; +- else +- ltq_mtd->map->phys = ltq_mtd->res->start; +- ltq_mtd->res->start; +- ltq_mtd->map->size = resource_size(ltq_mtd->res); +- ltq_mtd->map->virt = devm_ioremap_resource(&pdev->dev, ltq_mtd->res); +- if (IS_ERR(ltq_mtd->map->virt)) +- return PTR_ERR(ltq_mtd->map->virt); +- +- ltq_mtd->map->name = ltq_map_name; +- ltq_mtd->map->bankwidth = 2; +- ltq_mtd->map->read = ltq_read16; +- ltq_mtd->map->write = ltq_write16; +- ltq_mtd->map->copy_from = ltq_copy_from; +- ltq_mtd->map->copy_to = ltq_copy_to; +- +- ltq_mtd->map->map_priv_1 = LTQ_NOR_PROBING; +- ltq_mtd->mtd = do_map_probe("cfi_probe", ltq_mtd->map); +- ltq_mtd->map->map_priv_1 = LTQ_NOR_NORMAL; +- +- if (!ltq_mtd->mtd) { +- dev_err(&pdev->dev, "probing failed\n"); +- return -ENXIO; ++ if (devices_found == 1) { ++ ltq_mtd->cmtd = ltq_mtd->mtd[0]; ++ } else if (devices_found > 1) { ++ /* ++ * We detected multiple devices. Concatenate them together. ++ */ ++ ltq_mtd->cmtd = mtd_concat_create(ltq_mtd->mtd, devices_found, dev_name(&pdev->dev)); ++ if (ltq_mtd->cmtd == NULL) ++ err = -ENXIO; + } + +- ltq_mtd->mtd->dev.parent = &pdev->dev; +- mtd_set_of_node(ltq_mtd->mtd, pdev->dev.of_node); +- +- cfi = ltq_mtd->map->fldrv_priv; +- cfi->addr_unlock1 ^= 1; +- cfi->addr_unlock2 ^= 1; ++ ltq_mtd->cmtd->dev.parent = &pdev->dev; ++ mtd_set_of_node(ltq_mtd->cmtd, pdev->dev.of_node); + +- err = mtd_device_register(ltq_mtd->mtd, NULL, 0); ++ err = mtd_device_register(ltq_mtd->cmtd, NULL, 0); + if (err) { + dev_err(&pdev->dev, "failed to add partitions\n"); +- goto err_destroy; ++ goto err_out; + } + + return 0; + +-err_destroy: +- map_destroy(ltq_mtd->mtd); ++err_out: ++ ltq_mtd_remove(pdev); + return err; + } + +-static int +-ltq_mtd_remove(struct platform_device *pdev) +-{ +- struct ltq_mtd *ltq_mtd = platform_get_drvdata(pdev); +- +- if (ltq_mtd && ltq_mtd->mtd) { +- mtd_device_unregister(ltq_mtd->mtd); +- map_destroy(ltq_mtd->mtd); +- } +- return 0; +-} +- + static const struct of_device_id ltq_mtd_match[] = { + { .compatible = "lantiq,nor" }, + {}, diff --git a/target/linux/lantiq/patches-4.19/0300-MTD-cfi-cmdset-0001-disable-buffered-writes.patch b/target/linux/lantiq/patches-4.19/0300-MTD-cfi-cmdset-0001-disable-buffered-writes.patch new file mode 100644 index 0000000000..d153c521d3 --- /dev/null +++ b/target/linux/lantiq/patches-4.19/0300-MTD-cfi-cmdset-0001-disable-buffered-writes.patch @@ -0,0 +1,11 @@ +--- a/drivers/mtd/chips/cfi_cmdset_0001.c ++++ b/drivers/mtd/chips/cfi_cmdset_0001.c +@@ -39,7 +39,7 @@ + /* #define CMDSET0001_DISABLE_WRITE_SUSPEND */ + + // debugging, turns off buffer write mode if set to 1 +-#define FORCE_WORD_WRITE 0 ++#define FORCE_WORD_WRITE 1 + + /* Intel chips */ + #define I82802AB 0x00ad diff --git a/target/linux/lantiq/patches-4.19/0301-xrx200-add-gphy-clk-src-device-tree-binding.patch b/target/linux/lantiq/patches-4.19/0301-xrx200-add-gphy-clk-src-device-tree-binding.patch new file mode 100644 index 0000000000..ae8efcfdc0 --- /dev/null +++ b/target/linux/lantiq/patches-4.19/0301-xrx200-add-gphy-clk-src-device-tree-binding.patch @@ -0,0 +1,30 @@ +--- a/arch/mips/lantiq/xway/sysctrl.c ++++ b/arch/mips/lantiq/xway/sysctrl.c +@@ -424,6 +424,20 @@ static void clkdev_add_clkout(void) + } + } + ++static void set_phy_clock_source(struct device_node *np_cgu) ++{ ++ u32 phy_clk_src, ifcc; ++ ++ if (!np_cgu) ++ return; ++ ++ if (of_property_read_u32(np_cgu, "lantiq,phy-clk-src", &phy_clk_src)) ++ return; ++ ++ ifcc = ltq_cgu_r32(ifccr) & ~(0x1c); ++ ltq_cgu_w32(ifcc | (phy_clk_src << 2), ifccr); ++} ++ + /* bring up all register ranges that we need for basic system control */ + void __init ltq_soc_init(void) + { +@@ -589,4 +603,6 @@ void __init ltq_soc_init(void) + clkdev_add_pmu("1e100400.serial", NULL, 1, 0, PMU_ASC0); + } + usb_set_clock(); ++ ++ set_phy_clock_source(np_cgu); + } diff --git a/target/linux/lantiq/patches-4.19/0701-NET-lantiq-etop-of-mido.patch b/target/linux/lantiq/patches-4.19/0701-NET-lantiq-etop-of-mido.patch new file mode 100644 index 0000000000..5dc4b81522 --- /dev/null +++ b/target/linux/lantiq/patches-4.19/0701-NET-lantiq-etop-of-mido.patch @@ -0,0 +1,37 @@ +--- a/drivers/net/ethernet/lantiq_etop.c ++++ b/drivers/net/ethernet/lantiq_etop.c +@@ -40,6 +40,7 @@ + #include + #include + #include ++#include + + #include + +@@ -567,7 +568,8 @@ static int + ltq_etop_mdio_init(struct net_device *dev) + { + struct ltq_etop_priv *priv = netdev_priv(dev); +- int err; ++ struct device_node *mdio_np = NULL; ++ int err, ret; + + priv->mii_bus = mdiobus_alloc(); + if (!priv->mii_bus) { +@@ -587,7 +589,15 @@ ltq_etop_mdio_init(struct net_device *de + priv->mii_bus->name = "ltq_mii"; + snprintf(priv->mii_bus->id, MII_BUS_ID_SIZE, "%s-%x", + priv->pdev->name, priv->pdev->id); +- if (mdiobus_register(priv->mii_bus)) { ++ ++ mdio_np = of_get_child_by_name(priv->pdev->dev.of_node, "mdio-bus"); ++ ++ if (mdio_np) ++ ret = of_mdiobus_register(priv->mii_bus, mdio_np); ++ else ++ ret = mdiobus_register(priv->mii_bus); ++ ++ if (ret) { + err = -ENXIO; + goto err_out_free_mdiobus; + } diff --git a/target/linux/lantiq/xrx200/config-4.19 b/target/linux/lantiq/xrx200/config-4.19 new file mode 100644 index 0000000000..7b15d4283b --- /dev/null +++ b/target/linux/lantiq/xrx200/config-4.19 @@ -0,0 +1,97 @@ +CONFIG_ADM6996_PHY=y +CONFIG_AR8216_PHY=y +CONFIG_AT803X_PHY=y +CONFIG_BLK_MQ_PCI=y +CONFIG_CPU_MIPSR2_IRQ_EI=y +CONFIG_CPU_MIPSR2_IRQ_VI=y +CONFIG_CPU_RMAP=y +CONFIG_CRC16=y +CONFIG_CRYPTO_ACOMP2=y +CONFIG_CRYPTO_AEAD=y +CONFIG_CRYPTO_AEAD2=y +CONFIG_CRYPTO_DEFLATE=y +CONFIG_CRYPTO_LZO=y +CONFIG_CRYPTO_MANAGER=y +CONFIG_CRYPTO_MANAGER2=y +CONFIG_CRYPTO_NULL2=y +CONFIG_EXTRA_FIRMWARE="lantiq/xrx200_phy11g_a14.bin lantiq/xrx200_phy11g_a22.bin lantiq/xrx200_phy22f_a14.bin lantiq/xrx200_phy22f_a22.bin" +CONFIG_EXTRA_FIRMWARE_DIR="firmware" +CONFIG_FIRMWARE_IN_KERNEL=y +CONFIG_HWMON=y +CONFIG_ICPLUS_PHY=y +CONFIG_IFX_VPE_EXT=y +CONFIG_INPUT=y +CONFIG_INPUT_EVDEV=y +CONFIG_INPUT_POLLDEV=y +CONFIG_INTEL_XWAY_PHY=y +# CONFIG_ISDN is not set +CONFIG_LANTIQ_XRX200=y +CONFIG_LEDS_TRIGGER_HEARTBEAT=y +CONFIG_LZO_COMPRESS=y +CONFIG_LZO_DECOMPRESS=y +CONFIG_MIPS_MT=y +# CONFIG_MIPS_MT_FPAFF is not set +CONFIG_MIPS_MT_SMP=y +CONFIG_MIPS_PERF_SHARED_TC_COUNTERS=y +CONFIG_MIPS_VPE_APSP_API=y +CONFIG_MIPS_VPE_APSP_API_MT=y +CONFIG_MIPS_VPE_LOADER=y +CONFIG_MIPS_VPE_LOADER_MT=y +CONFIG_MIPS_VPE_LOADER_TOM=y +CONFIG_MTD_NAND=y +CONFIG_MTD_NAND_ECC=y +CONFIG_MTD_NAND_PLATFORM=y +CONFIG_MTD_NAND_XWAY=y +# CONFIG_MTD_PHYSMAP_OF is not set +CONFIG_MTD_UBI=y +CONFIG_MTD_UBI_BEB_LIMIT=20 +CONFIG_MTD_UBI_BLOCK=y +# CONFIG_MTD_UBI_FASTMAP is not set +# CONFIG_MTD_UBI_GLUEBI is not set +CONFIG_MTD_UBI_WL_THRESHOLD=4096 +CONFIG_NET_FLOW_LIMIT=y +CONFIG_NLS=y +CONFIG_NR_CPUS=2 +CONFIG_OF_ADDRESS_PCI=y +CONFIG_OF_PCI=y +CONFIG_OF_PCI_IRQ=y +CONFIG_PADATA=y +CONFIG_PCI=y +CONFIG_PCIE_LANTIQ=y +CONFIG_PCI_DOMAINS=y +CONFIG_PCI_LANTIQ=y +CONFIG_POWER_RESET_GPIO=y +CONFIG_POWER_SUPPLY=y +CONFIG_QUEUED_RWLOCKS=y +CONFIG_QUEUED_SPINLOCKS=y +CONFIG_RCU_NEED_SEGCBLIST=y +CONFIG_RCU_STALL_COMMON=y +CONFIG_REGULATOR=y +CONFIG_REGULATOR_FIXED_VOLTAGE=y +CONFIG_RFS_ACCEL=y +CONFIG_RPS=y +CONFIG_RTL8306_PHY=y +CONFIG_RTL8366S_PHY=y +CONFIG_RTL8367B_PHY=y +CONFIG_RTL8367_PHY=y +CONFIG_SENSORS_LTQ_CPUTEMP=y +CONFIG_SMP=y +CONFIG_SMP_UP=y +CONFIG_SWCONFIG_LEDS=y +CONFIG_SYNC_R4K=y +CONFIG_SYS_SUPPORTS_SCHED_SMT=y +CONFIG_SYS_SUPPORTS_SMP=y +CONFIG_TREE_RCU=y +CONFIG_TREE_SRCU=y +CONFIG_UBIFS_FS=y +CONFIG_UBIFS_FS_ADVANCED_COMPR=y +CONFIG_UBIFS_FS_LZO=y +CONFIG_UBIFS_FS_ZLIB=y +CONFIG_USB=y +CONFIG_USB_COMMON=y +# CONFIG_USB_EHCI_HCD is not set +CONFIG_USB_SUPPORT=y +CONFIG_XPS=y +CONFIG_XRX200_PHY_FW=y +CONFIG_ZLIB_DEFLATE=y +CONFIG_ZLIB_INFLATE=y diff --git a/target/linux/lantiq/xway/config-4.19 b/target/linux/lantiq/xway/config-4.19 new file mode 100644 index 0000000000..64a6c55832 --- /dev/null +++ b/target/linux/lantiq/xway/config-4.19 @@ -0,0 +1,51 @@ +CONFIG_ADM6996_PHY=y +CONFIG_AR8216_PHY=y +CONFIG_AT803X_PHY=y +CONFIG_BLK_MQ_PCI=y +CONFIG_CRC16=y +CONFIG_CRYPTO_ACOMP2=y +CONFIG_CRYPTO_DEFLATE=y +CONFIG_CRYPTO_LZO=y +CONFIG_FIRMWARE_IN_KERNEL=y +CONFIG_INPUT=y +CONFIG_INPUT_EVDEV=y +CONFIG_INPUT_POLLDEV=y +# CONFIG_ISDN is not set +CONFIG_LEDS_TRIGGER_HEARTBEAT=y +CONFIG_LZO_COMPRESS=y +CONFIG_LZO_DECOMPRESS=y +CONFIG_MTD_NAND=y +CONFIG_MTD_NAND_ECC=y +CONFIG_MTD_NAND_PLATFORM=y +CONFIG_MTD_NAND_XWAY=y +# CONFIG_MTD_PHYSMAP_OF is not set +CONFIG_MTD_UBI=y +CONFIG_MTD_UBI_BEB_LIMIT=20 +CONFIG_MTD_UBI_BLOCK=y +# CONFIG_MTD_UBI_FASTMAP is not set +# CONFIG_MTD_UBI_GLUEBI is not set +CONFIG_MTD_UBI_WL_THRESHOLD=4096 +CONFIG_NLS=y +CONFIG_OF_ADDRESS_PCI=y +CONFIG_OF_PCI=y +CONFIG_OF_PCI_IRQ=y +CONFIG_PCI=y +# CONFIG_PCIE_LANTIQ is not set +CONFIG_PCI_DOMAINS=y +CONFIG_PCI_LANTIQ=y +CONFIG_REGULATOR=y +CONFIG_REGULATOR_FIXED_VOLTAGE=y +CONFIG_RTL8306_PHY=y +CONFIG_RTL8366S_PHY=y +CONFIG_RTL8367B_PHY=y +CONFIG_RTL8367_PHY=y +CONFIG_UBIFS_FS=y +CONFIG_UBIFS_FS_ADVANCED_COMPR=y +CONFIG_UBIFS_FS_LZO=y +CONFIG_UBIFS_FS_ZLIB=y +CONFIG_USB=y +CONFIG_USB_COMMON=y +# CONFIG_USB_EHCI_HCD is not set +CONFIG_USB_SUPPORT=y +CONFIG_ZLIB_DEFLATE=y +CONFIG_ZLIB_INFLATE=y diff --git a/target/linux/lantiq/xway_legacy/config-4.19 b/target/linux/lantiq/xway_legacy/config-4.19 new file mode 100644 index 0000000000..feb82c5fcf --- /dev/null +++ b/target/linux/lantiq/xway_legacy/config-4.19 @@ -0,0 +1,39 @@ +CONFIG_ADM6996_PHY=y +CONFIG_AR8216_PHY=y +CONFIG_BLK_MQ_PCI=y +CONFIG_CRC16=y +CONFIG_CRYPTO_ACOMP2=y +CONFIG_CRYPTO_DEFLATE=y +CONFIG_CRYPTO_LZO=y +CONFIG_FIRMWARE_IN_KERNEL=y +# CONFIG_GPIO_SYSFS is not set +# CONFIG_HW_RANDOM is not set +CONFIG_INPUT=y +CONFIG_INPUT_EVDEV=y +CONFIG_INPUT_POLLDEV=y +# CONFIG_ISDN is not set +CONFIG_LEDS_TRIGGER_HEARTBEAT=y +# CONFIG_LEDS_TRIGGER_TIMER is not set +CONFIG_LZO_COMPRESS=y +CONFIG_LZO_DECOMPRESS=y +# CONFIG_MTD_PHYSMAP_OF is not set +CONFIG_NLS=y +CONFIG_OF_ADDRESS_PCI=y +CONFIG_OF_PCI=y +CONFIG_OF_PCI_IRQ=y +CONFIG_PCI=y +# CONFIG_PCIE_LANTIQ is not set +CONFIG_PCI_DOMAINS=y +CONFIG_PCI_LANTIQ=y +CONFIG_REGULATOR=y +CONFIG_REGULATOR_FIXED_VOLTAGE=y +CONFIG_RTL8306_PHY=y +CONFIG_RTL8366S_PHY=y +CONFIG_RTL8367B_PHY=y +CONFIG_RTL8367_PHY=y +CONFIG_USB=y +CONFIG_USB_COMMON=y +# CONFIG_USB_EHCI_HCD is not set +CONFIG_USB_SUPPORT=y +CONFIG_ZLIB_DEFLATE=y +CONFIG_ZLIB_INFLATE=y