From: Felix Fietkau Date: Sat, 29 Sep 2018 16:06:52 +0000 (+0200) Subject: kirkwood: remove linux 4.9 support X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=f445953d9f7950ba40af39d3c0b6ead233db8511;p=openwrt%2Fstaging%2Fynezz.git kirkwood: remove linux 4.9 support Signed-off-by: Felix Fietkau --- diff --git a/target/linux/kirkwood/config-4.9 b/target/linux/kirkwood/config-4.9 deleted file mode 100644 index 86d999edb1..0000000000 --- a/target/linux/kirkwood/config-4.9 +++ /dev/null @@ -1,333 +0,0 @@ -CONFIG_ALIGNMENT_TRAP=y -CONFIG_ARCH_CLOCKSOURCE_DATA=y -CONFIG_ARCH_HAS_ELF_RANDOMIZE=y -CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y -CONFIG_ARCH_HAS_SG_CHAIN=y -CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y -CONFIG_ARCH_HIBERNATION_POSSIBLE=y -CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y -CONFIG_ARCH_MULTIPLATFORM=y -CONFIG_ARCH_MULTI_CPU_AUTO=y -# CONFIG_ARCH_MULTI_V4 is not set -# CONFIG_ARCH_MULTI_V4T is not set -CONFIG_ARCH_MULTI_V4_V5=y -CONFIG_ARCH_MULTI_V5=y -CONFIG_ARCH_MVEBU=y -CONFIG_ARCH_NR_GPIO=0 -# CONFIG_ARCH_OXNAS is not set -# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set -# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set -CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y -CONFIG_ARCH_SUPPORTS_BIG_ENDIAN=y -CONFIG_ARCH_SUPPORTS_UPROBES=y -CONFIG_ARCH_SUSPEND_POSSIBLE=y -CONFIG_ARCH_USE_BUILTIN_BSWAP=y -CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y -CONFIG_ARCH_WANT_GENERAL_HUGETLB=y -CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y -CONFIG_ARCH_WANT_LIBATA_LEDS=y -CONFIG_ARM=y -# CONFIG_ARMADA_THERMAL is not set -CONFIG_ARM_APPENDED_DTB=y -CONFIG_ARM_ATAG_DTB_COMPAT=y -# CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND is not set -CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER=y -# CONFIG_ARM_CPU_SUSPEND is not set -CONFIG_ARM_HAS_SG_CHAIN=y -# CONFIG_ARM_KIRKWOOD_CPUIDLE is not set -CONFIG_ARM_L1_CACHE_SHIFT=5 -# CONFIG_ARM_MVEBU_V7_CPUIDLE is not set -CONFIG_ARM_PATCH_PHYS_VIRT=y -# CONFIG_ARM_THUMB is not set -CONFIG_ATA=y -CONFIG_ATAGS=y -CONFIG_ATA_LEDS=y -CONFIG_AUTO_ZRELADDR=y -# CONFIG_BINFMT_FLAT is not set -CONFIG_BLK_DEV_SD=y -CONFIG_BLK_MQ_PCI=y -CONFIG_CACHE_FEROCEON_L2=y -# CONFIG_CACHE_FEROCEON_L2_WRITETHROUGH is not set -# CONFIG_CACHE_L2X0 is not set -CONFIG_CLKDEV_LOOKUP=y -CONFIG_CLKSRC_MMIO=y -CONFIG_CLKSRC_OF=y -CONFIG_CLKSRC_PROBE=y -CONFIG_CLONE_BACKWARDS=y -CONFIG_COMMON_CLK=y -CONFIG_CPU_32v5=y -CONFIG_CPU_ABRT_EV5T=y -# CONFIG_CPU_BIG_ENDIAN is not set -CONFIG_CPU_CACHE_VIVT=y -CONFIG_CPU_COPY_FEROCEON=y -CONFIG_CPU_CP15=y -CONFIG_CPU_CP15_MMU=y -CONFIG_CPU_FEROCEON=y -# CONFIG_CPU_FEROCEON_OLD_ID is not set -# CONFIG_CPU_ICACHE_DISABLE is not set -CONFIG_CPU_IDLE=y -CONFIG_CPU_IDLE_GOV_LADDER=y -CONFIG_CPU_PABRT_LEGACY=y -CONFIG_CPU_PM=y -CONFIG_CPU_TLB_FEROCEON=y -CONFIG_CPU_USE_DOMAINS=y -CONFIG_CRC16=y -# CONFIG_CRC32_SARWATE is not set -CONFIG_CRC32_SLICEBY8=y -CONFIG_CRYPTO_CRC32C=y -CONFIG_CRYPTO_DEFLATE=y -CONFIG_CRYPTO_DES=y -CONFIG_CRYPTO_DEV_MARVELL_CESA=y -CONFIG_CRYPTO_HASH=y -CONFIG_CRYPTO_HASH2=y -CONFIG_CRYPTO_HW=y -CONFIG_CRYPTO_LZO=y -CONFIG_CRYPTO_RNG2=y -CONFIG_CRYPTO_WORKQUEUE=y -CONFIG_DEBUG_LL=y -CONFIG_DEBUG_LL_INCLUDE="debug/8250.S" -CONFIG_DEBUG_MVEBU_UART0_ALTERNATE=y -# CONFIG_DEBUG_MVEBU_UART1_ALTERNATE is not set -CONFIG_DEBUG_UART_8250=y -# CONFIG_DEBUG_UART_8250_FLOW_CONTROL is not set -CONFIG_DEBUG_UART_8250_SHIFT=2 -# CONFIG_DEBUG_UART_8250_WORD is not set -CONFIG_DEBUG_UART_PHYS=0xf1012000 -CONFIG_DEBUG_UART_VIRT=0xfed12000 -CONFIG_DEBUG_UNCOMPRESS=y -# CONFIG_DEBUG_USER is not set -# CONFIG_DLCI is not set -CONFIG_DNOTIFY=y -CONFIG_DTC=y -# CONFIG_EARLY_PRINTK is not set -CONFIG_EDAC_ATOMIC_SCRUB=y -CONFIG_EDAC_SUPPORT=y -CONFIG_EXT4_FS=y -CONFIG_FIXED_PHY=y -CONFIG_FIX_EARLYCON_MEM=y -CONFIG_FRAME_POINTER=y -CONFIG_FS_MBCACHE=y -CONFIG_GENERIC_ALLOCATOR=y -CONFIG_GENERIC_ATOMIC64=y -CONFIG_GENERIC_BUG=y -CONFIG_GENERIC_CLOCKEVENTS=y -CONFIG_GENERIC_EARLY_IOREMAP=y -CONFIG_GENERIC_IDLE_POLL_SETUP=y -CONFIG_GENERIC_IO=y -CONFIG_GENERIC_IRQ_CHIP=y -CONFIG_GENERIC_IRQ_SHOW=y -CONFIG_GENERIC_IRQ_SHOW_LEVEL=y -CONFIG_GENERIC_PCI_IOMAP=y -CONFIG_GENERIC_PHY=y -CONFIG_GENERIC_SCHED_CLOCK=y -CONFIG_GENERIC_SMP_IDLE_THREAD=y -CONFIG_GENERIC_STRNCPY_FROM_USER=y -CONFIG_GENERIC_STRNLEN_USER=y -CONFIG_GLOB=y -CONFIG_GPIOLIB=y -CONFIG_GPIO_MVEBU=y -CONFIG_GPIO_SYSFS=y -CONFIG_HANDLE_DOMAIN_IRQ=y -CONFIG_HARDIRQS_SW_RESEND=y -CONFIG_HAS_DMA=y -CONFIG_HAS_IOMEM=y -CONFIG_HAS_IOPORT_MAP=y -# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set -CONFIG_HAVE_ARCH_AUDITSYSCALL=y -# CONFIG_HAVE_ARCH_BITREVERSE is not set -CONFIG_HAVE_ARCH_JUMP_LABEL=y -CONFIG_HAVE_ARCH_KGDB=y -CONFIG_HAVE_ARCH_PFN_VALID=y -CONFIG_HAVE_ARCH_SECCOMP_FILTER=y -CONFIG_HAVE_ARCH_TRACEHOOK=y -# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set -CONFIG_HAVE_CBPF_JIT=y -CONFIG_HAVE_CC_STACKPROTECTOR=y -CONFIG_HAVE_CLK=y -CONFIG_HAVE_CLK_PREPARE=y -CONFIG_HAVE_CONTEXT_TRACKING=y -CONFIG_HAVE_C_RECORDMCOUNT=y -CONFIG_HAVE_DEBUG_KMEMLEAK=y -CONFIG_HAVE_DMA_API_DEBUG=y -CONFIG_HAVE_DMA_CONTIGUOUS=y -CONFIG_HAVE_DYNAMIC_FTRACE=y -CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y -CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y -CONFIG_HAVE_FUNCTION_TRACER=y -CONFIG_HAVE_GENERIC_DMA_COHERENT=y -CONFIG_HAVE_IDE=y -CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y -CONFIG_HAVE_MEMBLOCK=y -CONFIG_HAVE_MOD_ARCH_SPECIFIC=y -CONFIG_HAVE_NET_DSA=y -CONFIG_HAVE_OPROFILE=y -CONFIG_HAVE_OPTPROBES=y -CONFIG_HAVE_PERF_EVENTS=y -CONFIG_HAVE_PERF_REGS=y -CONFIG_HAVE_PERF_USER_STACK_DUMP=y -CONFIG_HAVE_PROC_CPU=y -CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y -CONFIG_HAVE_SYSCALL_TRACEPOINTS=y -CONFIG_HAVE_UID16=y -CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y -CONFIG_HW_RANDOM=y -CONFIG_HZ_FIXED=0 -CONFIG_HZ_PERIODIC=y -CONFIG_I2C=y -CONFIG_I2C_BOARDINFO=y -CONFIG_I2C_CHARDEV=y -CONFIG_I2C_MV64XXX=y -CONFIG_INITRAMFS_SOURCE="" -CONFIG_IOMMU_HELPER=y -CONFIG_IP_PIMSM_V1=y -CONFIG_IP_PIMSM_V2=y -CONFIG_IRQCHIP=y -CONFIG_IRQ_DOMAIN=y -CONFIG_IRQ_FORCED_THREADING=y -CONFIG_IRQ_WORK=y -CONFIG_JBD2=y -CONFIG_KIRKWOOD_CLK=y -CONFIG_KIRKWOOD_THERMAL=y -CONFIG_LEDS_GPIO=y -CONFIG_LEDS_NETXBIG=y -CONFIG_LEDS_NS2=y -CONFIG_LEGACY_PTYS=y -CONFIG_LEGACY_PTY_COUNT=256 -CONFIG_LIBFDT=y -CONFIG_LZO_COMPRESS=y -CONFIG_LZO_DECOMPRESS=y -CONFIG_MACH_KIRKWOOD=y -CONFIG_MACH_MVEBU_ANY=y -CONFIG_MANGLE_BOOTARGS=y -CONFIG_MDIO_BOARDINFO=y -# CONFIG_MFD_MAX77620 is not set -CONFIG_MIGHT_HAVE_PCI=y -CONFIG_MMC=y -CONFIG_MMC_BLOCK=y -CONFIG_MMC_MVSDIO=y -# CONFIG_MMC_TIFM_SD is not set -CONFIG_MODULES_USE_ELF_REL=y -# CONFIG_MTD_CFI is not set -CONFIG_MTD_CMDLINE_PARTS=y -CONFIG_MTD_NAND=y -CONFIG_MTD_NAND_ECC=y -CONFIG_MTD_NAND_ORION=y -CONFIG_MTD_UBI=y -CONFIG_MTD_UBI_BEB_LIMIT=20 -CONFIG_MTD_UBI_BLOCK=y -# CONFIG_MTD_UBI_FASTMAP is not set -# CONFIG_MTD_UBI_GLUEBI is not set -CONFIG_MTD_UBI_WL_THRESHOLD=4096 -CONFIG_MULTI_IRQ_HANDLER=y -CONFIG_MV643XX_ETH=y -CONFIG_MVEBU_CLK_COMMON=y -CONFIG_MVEBU_MBUS=y -CONFIG_MVMDIO=y -# CONFIG_MVNETA is not set -CONFIG_MVSW61XX_PHY=y -CONFIG_NEED_DMA_MAP_STATE=y -CONFIG_NEED_KUSER_HELPERS=y -CONFIG_NEED_PER_CPU_KM=y -CONFIG_NLS=y -CONFIG_NO_BOOTMEM=y -CONFIG_OF=y -CONFIG_OF_ADDRESS=y -CONFIG_OF_ADDRESS_PCI=y -CONFIG_OF_EARLY_FLATTREE=y -CONFIG_OF_FLATTREE=y -CONFIG_OF_GPIO=y -CONFIG_OF_IRQ=y -CONFIG_OF_MDIO=y -CONFIG_OF_NET=y -CONFIG_OF_PCI=y -CONFIG_OF_PCI_IRQ=y -CONFIG_OF_RESERVED_MEM=y -CONFIG_OLD_SIGACTION=y -CONFIG_OLD_SIGSUSPEND3=y -CONFIG_ORION_IRQCHIP=y -CONFIG_ORION_TIMER=y -CONFIG_ORION_WATCHDOG=y -CONFIG_OUTER_CACHE=y -CONFIG_PAGE_OFFSET=0xC0000000 -CONFIG_PCI=y -CONFIG_PCI_DOMAINS=y -CONFIG_PCI_DOMAINS_GENERIC=y -CONFIG_PCI_MVEBU=y -CONFIG_PERF_USE_VMALLOC=y -CONFIG_PGTABLE_LEVELS=2 -CONFIG_PHYLIB=y -CONFIG_PHY_MVEBU_SATA=y -CONFIG_PINCTRL=y -CONFIG_PINCTRL_KIRKWOOD=y -CONFIG_PINCTRL_MVEBU=y -# CONFIG_PINCTRL_SINGLE is not set -CONFIG_PLAT_ORION=y -CONFIG_POWER_RESET=y -# CONFIG_POWER_RESET_BRCMKONA is not set -CONFIG_POWER_RESET_GPIO=y -# CONFIG_POWER_RESET_QNAP is not set -CONFIG_POWER_SUPPLY=y -CONFIG_RATIONAL=y -# CONFIG_RCU_STALL_COMMON is not set -CONFIG_REGMAP=y -CONFIG_REGMAP_I2C=y -CONFIG_REGMAP_SPI=y -CONFIG_REGULATOR=y -CONFIG_REGULATOR_FIXED_VOLTAGE=y -CONFIG_RTC_CLASS=y -CONFIG_RTC_DRV_MV=y -CONFIG_RTC_I2C_AND_SPI=y -CONFIG_RTC_MC146818_LIB=y -CONFIG_RWSEM_XCHGADD_ALGORITHM=y -CONFIG_SATA_MV=y -# CONFIG_SCHED_INFO is not set -CONFIG_SCSI=y -CONFIG_SERIAL_8250_DEPRECATED_OPTIONS=y -CONFIG_SERIAL_8250_FSL=y -# CONFIG_SERIAL_MVEBU_UART is not set -CONFIG_SERIAL_OF_PLATFORM=y -CONFIG_SG_POOL=y -CONFIG_SOC_BUS=y -CONFIG_SPARSE_IRQ=y -CONFIG_SPI=y -CONFIG_SPI_MASTER=y -CONFIG_SPI_ORION=y -CONFIG_SPLIT_PTLOCK_CPUS=999999 -CONFIG_SRAM=y -CONFIG_SRCU=y -CONFIG_SWCONFIG=y -CONFIG_SWIOTLB=y -CONFIG_SWPHY=y -CONFIG_SYS_SUPPORTS_APM_EMULATION=y -CONFIG_THERMAL=y -CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y -CONFIG_THERMAL_GOV_STEP_WISE=y -CONFIG_THERMAL_OF=y -CONFIG_TICK_CPU_ACCOUNTING=y -CONFIG_UBIFS_FS=y -CONFIG_UBIFS_FS_ADVANCED_COMPR=y -CONFIG_UBIFS_FS_LZO=y -CONFIG_UBIFS_FS_ZLIB=y -CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h" -CONFIG_USB=y -CONFIG_USB_COMMON=y -CONFIG_USB_EHCI_HCD=y -CONFIG_USB_EHCI_HCD_ORION=y -# CONFIG_USB_EHCI_HCD_PLATFORM is not set -CONFIG_USB_EHCI_PCI=y -CONFIG_USB_LED_TRIG=y -CONFIG_USB_STORAGE=y -CONFIG_USB_SUPPORT=y -# CONFIG_USB_UHCI_HCD is not set -CONFIG_USE_OF=y -CONFIG_VECTORS_BASE=0xffff0000 -# CONFIG_VFP is not set -CONFIG_VM_EVENT_COUNTERS=y -CONFIG_WAN=y -CONFIG_WATCHDOG_CORE=y -CONFIG_XZ_DEC_ARM=y -CONFIG_XZ_DEC_BCJ=y -CONFIG_ZBOOT_ROM_BSS=0x0 -CONFIG_ZBOOT_ROM_TEXT=0x0 -CONFIG_ZLIB_DEFLATE=y -CONFIG_ZLIB_INFLATE=y diff --git a/target/linux/kirkwood/patches-4.9/100-ib62x0.patch b/target/linux/kirkwood/patches-4.9/100-ib62x0.patch deleted file mode 100644 index f4e6947374..0000000000 --- a/target/linux/kirkwood/patches-4.9/100-ib62x0.patch +++ /dev/null @@ -1,30 +0,0 @@ ---- a/arch/arm/boot/dts/kirkwood-ib62x0.dts -+++ b/arch/arm/boot/dts/kirkwood-ib62x0.dts -@@ -5,7 +5,7 @@ - - / { - model = "RaidSonic ICY BOX IB-NAS62x0 (Rev B)"; -- compatible = "raidsonic,ib-nas6210-b", "raidsonic,ib-nas6220-b", "raidsonic,ib-nas6210", "raidsonic,ib-nas6220", "raidsonic,ib-nas62x0", "marvell,kirkwood-88f6281", "marvell,kirkwood"; -+ compatible = "raidsonic,ib-nas62x0", "marvell,kirkwood-88f6281", "marvell,kirkwood"; - - memory { - device_type = "memory"; -@@ -117,13 +117,13 @@ - }; - - partition@100000 { -- label = "uImage"; -- reg = <0x0100000 0x600000>; -+ label = "second stage u-boot"; -+ reg = <0x100000 0x200000>; - }; - -- partition@700000 { -- label = "root"; -- reg = <0x0700000 0xf900000>; -+ partition@200000 { -+ label = "ubi"; -+ reg = <0x200000 0xfe00000>; - }; - - }; diff --git a/target/linux/kirkwood/patches-4.9/101-iconnect.patch b/target/linux/kirkwood/patches-4.9/101-iconnect.patch deleted file mode 100644 index 17705eae19..0000000000 --- a/target/linux/kirkwood/patches-4.9/101-iconnect.patch +++ /dev/null @@ -1,50 +0,0 @@ ---- a/arch/arm/boot/dts/kirkwood-iconnect.dts -+++ b/arch/arm/boot/dts/kirkwood-iconnect.dts -@@ -15,8 +15,6 @@ - chosen { - bootargs = "console=ttyS0,115200n8 earlyprintk"; - stdout-path = &uart0; -- linux,initrd-start = <0x4500040>; -- linux,initrd-end = <0x4800000>; - }; - - ocp@f1000000 { -@@ -145,28 +143,23 @@ - status = "okay"; - - partition@0 { -- label = "uboot"; -- reg = <0x0000000 0xc0000>; -+ label = "u-boot"; -+ reg = <0x0000000 0xe0000>; - }; - -- partition@a0000 { -- label = "env"; -- reg = <0xa0000 0x20000>; -+ partition@e0000 { -+ label = "u-boot environment"; -+ reg = <0xe0000 0x100000>; - }; - - partition@100000 { -- label = "zImage"; -- reg = <0x100000 0x300000>; -+ label = "second stage u-boot"; -+ reg = <0x100000 0x200000>; - }; - -- partition@540000 { -- label = "initrd"; -- reg = <0x540000 0x300000>; -- }; -- -- partition@980000 { -- label = "boot"; -- reg = <0x980000 0x1f400000>; -+ partition@200000 { -+ label = "ubi"; -+ reg = <0x200000 0x1fe00000>; - }; - }; - diff --git a/target/linux/kirkwood/patches-4.9/102-dockstar.patch b/target/linux/kirkwood/patches-4.9/102-dockstar.patch deleted file mode 100644 index f66e19d27f..0000000000 --- a/target/linux/kirkwood/patches-4.9/102-dockstar.patch +++ /dev/null @@ -1,32 +0,0 @@ ---- a/arch/arm/boot/dts/kirkwood-dockstar.dts -+++ b/arch/arm/boot/dts/kirkwood-dockstar.dts -@@ -77,18 +77,22 @@ - - partition@0 { - label = "u-boot"; -- reg = <0x0000000 0x100000>; -- read-only; -+ reg = <0x0000000 0xe0000>; -+ }; -+ -+ partition@e0000 { -+ label = "u-boot environment"; -+ reg = <0xe0000 0x100000>; - }; - - partition@100000 { -- label = "uImage"; -- reg = <0x0100000 0x400000>; -+ label = "second stage u-boot"; -+ reg = <0x100000 0x200000>; - }; - -- partition@500000 { -- label = "data"; -- reg = <0x0500000 0xfb00000>; -+ partition@200000 { -+ label = "ubi"; -+ reg = <0x200000 0xfe00000>; - }; - }; - diff --git a/target/linux/kirkwood/patches-4.9/103-iomega-ix2-200.patch b/target/linux/kirkwood/patches-4.9/103-iomega-ix2-200.patch deleted file mode 100644 index f3c06cd5f0..0000000000 --- a/target/linux/kirkwood/patches-4.9/103-iomega-ix2-200.patch +++ /dev/null @@ -1,33 +0,0 @@ ---- a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts -+++ b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts -@@ -185,18 +185,18 @@ - }; - - partition@a0000 { -- label = "env"; -+ label = "u-boot environment"; - reg = <0xa0000 0x20000>; - read-only; - }; - - partition@100000 { -- label = "uImage"; -+ label = "kernel"; - reg = <0x100000 0x300000>; - }; - - partition@400000 { -- label = "rootfs"; -+ label = "ubi"; - reg = <0x400000 0x1C00000>; - }; - }; -@@ -210,7 +210,7 @@ - }; - - ð0 { -- status = "okay"; -+ status = "disabled"; - ethernet0-port@0 { - speed = <1000>; - duplex = <1>; diff --git a/target/linux/kirkwood/patches-4.9/104-ea3500.patch b/target/linux/kirkwood/patches-4.9/104-ea3500.patch deleted file mode 100644 index 3659f879b9..0000000000 --- a/target/linux/kirkwood/patches-4.9/104-ea3500.patch +++ /dev/null @@ -1,258 +0,0 @@ ---- a/arch/arm/boot/dts/Makefile -+++ b/arch/arm/boot/dts/Makefile -@@ -220,6 +220,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ - kirkwood-linkstation-lswsxl.dtb \ - kirkwood-linkstation-lswvl.dtb \ - kirkwood-linkstation-lswxl.dtb \ -+ kirkwood-linksys-audi.dtb \ - kirkwood-linksys-viper.dtb \ - kirkwood-lschlv2.dtb \ - kirkwood-lsxhl.dtb \ ---- /dev/null -+++ b/arch/arm/boot/dts/kirkwood-linksys-audi.dts -@@ -0,0 +1,245 @@ -+/* -+ * kirkwood-linksys-audi.dts - Device Tree file for Linksys EA3500 -+ * -+ * (c) 2013 Jonas Gorski -+ * (c) 2013 Deutsche Telekom Innovation Laboratories -+ * (c) 2014 Luka Perkov -+ * (c) 2014 Dan Walters -+ * -+ * This file is licensed under the terms of the GNU General Public -+ * License version 2. This program is licensed "as is" without any -+ * warranty of any kind, whether express or implied. -+ */ -+ -+/dts-v1/; -+ -+#include "kirkwood.dtsi" -+#include "kirkwood-6282.dtsi" -+ -+/ { -+ model = "Linksys Audi (EA3500)"; -+ compatible = "linksys,audi", "marvell,kirkwood-88f6282", "marvell,kirkwood"; -+ -+ memory { -+ device_type = "memory"; -+ reg = <0x00000000 0x4000000>; -+ }; -+ -+ aliases { -+ serial0 = &uart0; -+ }; -+ -+ chosen { -+ stdout-path = "serial0:115200n8"; -+ }; -+ -+ gpio_keys { -+ compatible = "gpio-keys"; -+ #address-cells = <1>; -+ #size-cells = <0>; -+ pinctrl-0 = < &pmx_btn_wps &pmx_btn_reset >; -+ pinctrl-names = "default"; -+ -+ wps { -+ label = "WPS Button"; -+ linux,code = ; -+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; -+ }; -+ -+ reset { -+ label = "Reset Button"; -+ linux,code = ; -+ gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; -+ }; -+ }; -+ -+ gpio-leds { -+ compatible = "gpio-leds"; -+ pinctrl-0 = < &pmx_led_green_power >; -+ pinctrl-names = "default"; -+ -+ green-power { -+ label = "audi:green:power"; -+ gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; -+ }; -+ }; -+ -+ mvsw61xx { -+ compatible = "marvell,88e6171"; -+ status = "okay"; -+ reg = <0x10>; -+ -+ mii-bus = <&mdio>; -+ cpu-port-0 = <5>; -+ cpu-port-1 = <6>; -+ is-indirect; -+ }; -+ -+ dsa { -+ compatible = "marvell,dsa"; -+ #address-cells = <2>; -+ #size-cells = <0>; -+ -+ dsa,ethernet = <ð0port>; -+ dsa,mii-bus = <&mdio>; -+ -+ switch@16,0 { -+ #address-cells = <1>; -+ #size-cells = <0>; -+ reg = <16 0>; /* MDIO address 16, switch 0 in tree */ -+ -+ port@0 { -+ reg = <0>; -+ label = "ethernet1"; -+ }; -+ -+ port@1 { -+ reg = <1>; -+ label = "ethernet2"; -+ }; -+ -+ port@2 { -+ reg = <2>; -+ label = "ethernet3"; -+ }; -+ -+ port@3 { -+ reg = <3>; -+ label = "ethernet4"; -+ }; -+ -+ port@4 { -+ reg = <4>; -+ label = "internet"; -+ }; -+ -+ port@5 { -+ reg = <5>; -+ label = "cpu"; -+ }; -+ }; -+ }; -+}; -+ -+&pinctrl { -+ pmx_led_green_power: pmx-led-green-power { -+ marvell,pins = "mpp7"; -+ marvell,function = "gpo"; -+ }; -+ pmx_btn_wps: pmx-btn-wps { -+ marvell,pins = "mpp47"; -+ marvell,function = "gpio"; -+ }; -+ pmx_btn_reset: pmx-btn-reset { -+ marvell,pins = "mpp48"; -+ marvell,function = "gpio"; -+ }; -+}; -+ -+&nand { -+ status = "okay"; -+ pinctrl-0 = <&pmx_nand>; -+ pinctrl-names = "default"; -+ -+ partitions { -+ compatible = "fixed-partitions"; -+ #address-cells = <1>; -+ #size-cells = <1>; -+ -+ partition@0 { -+ label = "u-boot"; -+ reg = <0x0 0x80000>; -+ read-only; -+ }; -+ -+ partition@80000 { -+ label = "u_env"; -+ reg = <0x80000 0x4000>; -+ }; -+ -+ partition@84000 { -+ label = "s_env"; -+ reg = <0x84000 0x4000>; -+ }; -+ -+ partition@200000 { -+ label = "kernel1"; -+ reg = <0x200000 0x290000>; -+ }; -+ -+ partition@490000 { -+ label = "rootfs1"; -+ reg = <0x490000 0x1170000>; -+ }; -+ -+ partition@1600000 { -+ label = "kernel2"; -+ reg = <0x1600000 0x290000>; -+ }; -+ -+ partition@1890000 { -+ label = "rootfs2"; -+ reg = <0x1890000 0x1170000>; -+ }; -+ -+ partition@2a00000 { -+ label = "syscfg"; -+ reg = <0x2a00000 0x1600000>; -+ }; -+ -+ partition@88000 { -+ label = "unused"; -+ reg = <0x88000 0x178000>; -+ }; -+ -+ }; -+}; -+ -+&pciec { -+ status = "okay"; -+}; -+ -+&pcie0 { -+ status = "okay"; -+}; -+ -+&pcie1 { -+ status = "okay"; -+}; -+ -+&mdio { -+ status = "okay"; -+}; -+ -+&uart0 { -+ status = "okay"; -+}; -+ -+/* eth0 is connected to a Marvell 88E6171 switch, without a PHY. So set -+ * fixed speed and duplex. -+ */ -+ð0 { -+ status = "okay"; -+ ethernet0-port@0 { -+ speed = <1000>; -+ duplex = <1>; -+ }; -+}; -+ -+/* eth1 is connected to the switch at port 6. However DSA only supports a -+ * single CPU port. Upstream uses DSA so they disable this port to avoid confusion. -+ */ -+ð1 { -+ status = "okay"; -+ ethernet1-port@0 { -+ speed = <1000>; -+ duplex = <1>; -+ }; -+}; -+ -+/* There is no battery on the board, so the RTC does not keep -+ * time when there is no power, making it useless. -+ */ -+&rtc { -+ status = "disabled"; -+}; diff --git a/target/linux/kirkwood/patches-4.9/105-ea4500.patch b/target/linux/kirkwood/patches-4.9/105-ea4500.patch deleted file mode 100644 index d76cdace51..0000000000 --- a/target/linux/kirkwood/patches-4.9/105-ea4500.patch +++ /dev/null @@ -1,64 +0,0 @@ ---- a/arch/arm/boot/dts/kirkwood-linksys-viper.dts -+++ b/arch/arm/boot/dts/kirkwood-linksys-viper.dts -@@ -69,6 +69,17 @@ - }; - }; - -+ mvsw61xx { -+ compatible = "marvell,88e6171"; -+ status = "okay"; -+ reg = <0x10>; -+ -+ mii-bus = <&mdio>; -+ cpu-port-0 = <5>; -+ cpu-port-1 = <6>; -+ is-indirect; -+ }; -+ - dsa { - compatible = "marvell,dsa"; - #address-cells = <2>; -@@ -161,22 +172,22 @@ - }; - - partition@200000 { -- label = "kernel"; -+ label = "kernel1"; - reg = <0x200000 0x2A0000>; - }; - - partition@4A0000 { -- label = "rootfs"; -+ label = "rootfs1"; - reg = <0x4A0000 0x1760000>; - }; - - partition@1C00000 { -- label = "alt_kernel"; -+ label = "kernel2"; - reg = <0x1C00000 0x2A0000>; - }; - - partition@1EA0000 { -- label = "alt_rootfs"; -+ label = "rootfs2"; - reg = <0x1EA0000 0x1760000>; - }; - -@@ -225,10 +236,14 @@ - }; - - /* eth1 is connected to the switch at port 6. However DSA only supports a -- * single CPU port. So leave this port disabled to avoid confusion. -+ * single CPU port. Upstream uses DSA so they disable this port to avoid confusion. - */ - ð1 { -- status = "disabled"; -+ status = "okay"; -+ ethernet1-port@0 { -+ speed = <1000>; -+ duplex = <1>; -+ }; - }; - - /* There is no battery on the board, so the RTC does not keep diff --git a/target/linux/kirkwood/patches-4.9/105-goflexhome.patch b/target/linux/kirkwood/patches-4.9/105-goflexhome.patch deleted file mode 100644 index 0962249664..0000000000 --- a/target/linux/kirkwood/patches-4.9/105-goflexhome.patch +++ /dev/null @@ -1,130 +0,0 @@ ---- a/arch/arm/boot/dts/Makefile -+++ b/arch/arm/boot/dts/Makefile -@@ -207,6 +207,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ - kirkwood-ds411.dtb \ - kirkwood-ds411j.dtb \ - kirkwood-ds411slim.dtb \ -+ kirkwood-goflexhome.dtb \ - kirkwood-goflexnet.dtb \ - kirkwood-guruplug-server-plus.dtb \ - kirkwood-ib62x0.dtb \ ---- /dev/null -+++ b/arch/arm/boot/dts/kirkwood-goflexhome.dts -@@ -0,0 +1,117 @@ -+/dts-v1/; -+ -+#include "kirkwood.dtsi" -+#include "kirkwood-6281.dtsi" -+ -+/ { -+ model = "Seagate GoFlex Home"; -+ compatible = "seagate,goflexhome", "marvell,kirkwood-88f6281", "marvell,kirkwood"; -+ -+ memory { -+ device_type = "memory"; -+ reg = <0x00000000 0x8000000>; -+ }; -+ -+ chosen { -+ bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10"; -+ stdout-path = &uart0; -+ }; -+ -+ ocp@f1000000 { -+ pinctrl: pin-controller@10000 { -+ pmx_usb_power_enable: pmx-usb-power-enable { -+ marvell,pins = "mpp29"; -+ marvell,function = "gpio"; -+ }; -+ pmx_led_white: pmx-led-white { -+ marvell,pins = "mpp40"; -+ marvell,function = "gpio"; -+ }; -+ pmx_led_green: pmx-led_green { -+ marvell,pins = "mpp46"; -+ marvell,function = "gpio"; -+ }; -+ pmx_led_orange: pmx-led-orange { -+ marvell,pins = "mpp47"; -+ marvell,function = "gpio"; -+ }; -+ }; -+ serial@12000 { -+ status = "ok"; -+ }; -+ -+ sata@80000 { -+ status = "okay"; -+ nr-ports = <2>; -+ }; -+ -+ }; -+ gpio-leds { -+ compatible = "gpio-leds"; -+ -+ health { -+ label = "status:green:health"; -+ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; -+ linux,default-trigger = "default-on"; -+ }; -+ fault { -+ label = "status:orange:fault"; -+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; -+ }; -+ misc { -+ label = "status:white:misc"; -+ gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; -+ linux,default-trigger = "disk-activity"; -+ }; -+ }; -+ regulators { -+ compatible = "simple-bus"; -+ #address-cells = <1>; -+ #size-cells = <0>; -+ pinctrl-0 = <&pmx_usb_power_enable>; -+ pinctrl-names = "default"; -+ -+ usb_power: regulator@1 { -+ compatible = "regulator-fixed"; -+ reg = <1>; -+ regulator-name = "USB Power"; -+ regulator-min-microvolt = <5000000>; -+ regulator-max-microvolt = <5000000>; -+ enable-active-high; -+ regulator-always-on; -+ regulator-boot-on; -+ gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>; -+ }; -+ }; -+}; -+ -+&nand { -+ chip-delay = <40>; -+ status = "okay"; -+ -+ partition@0 { -+ label = "u-boot"; -+ reg = <0x0000000 0x100000>; -+ read-only; -+ }; -+ -+ partition@100000 { -+ label = "ubi"; -+ reg = <0x100000 0x0ff00000>; -+ }; -+}; -+ -+&mdio { -+ status = "okay"; -+ -+ ethphy0: ethernet-phy@0 { -+ reg = <0>; -+ }; -+}; -+ -+ð0 { -+ status = "okay"; -+ ethernet0-port@0 { -+ phy-handle = <ðphy0>; -+ }; -+}; diff --git a/target/linux/kirkwood/patches-4.9/106-goflexnet.patch b/target/linux/kirkwood/patches-4.9/106-goflexnet.patch deleted file mode 100644 index 9b0620b818..0000000000 --- a/target/linux/kirkwood/patches-4.9/106-goflexnet.patch +++ /dev/null @@ -1,23 +0,0 @@ ---- a/arch/arm/boot/dts/kirkwood-goflexnet.dts -+++ b/arch/arm/boot/dts/kirkwood-goflexnet.dts -@@ -158,18 +158,8 @@ - }; - - partition@100000 { -- label = "uImage"; -- reg = <0x0100000 0x400000>; -- }; -- -- partition@500000 { -- label = "pogoplug"; -- reg = <0x0500000 0x2000000>; -- }; -- -- partition@2500000 { -- label = "root"; -- reg = <0x02500000 0xd800000>; -+ label = "ubi"; -+ reg = <0x0100000 0x0ff00000>; - }; - }; - diff --git a/target/linux/kirkwood/patches-4.9/107-01-zyxel-nsa3x0-common-nand-partitions.patch b/target/linux/kirkwood/patches-4.9/107-01-zyxel-nsa3x0-common-nand-partitions.patch deleted file mode 100644 index a358e3962e..0000000000 --- a/target/linux/kirkwood/patches-4.9/107-01-zyxel-nsa3x0-common-nand-partitions.patch +++ /dev/null @@ -1,48 +0,0 @@ ---- a/arch/arm/boot/dts/kirkwood-nsa3x0-common.dtsi -+++ b/arch/arm/boot/dts/kirkwood-nsa3x0-common.dtsi -@@ -111,40 +111,16 @@ - - partition@0 { - label = "uboot"; -- reg = <0x0000000 0x0100000>; -+ reg = <0x0000000 0x00c0000>; - read-only; - }; - partition@100000 { - label = "uboot_env"; -- reg = <0x0100000 0x0080000>; -+ reg = <0x00c0000 0x0080000>; - }; -- partition@180000 { -- label = "key_store"; -- reg = <0x0180000 0x0080000>; -- }; -- partition@200000 { -- label = "info"; -- reg = <0x0200000 0x0080000>; -- }; -- partition@280000 { -- label = "etc"; -- reg = <0x0280000 0x0a00000>; -- }; -- partition@c80000 { -- label = "kernel_1"; -- reg = <0x0c80000 0x0a00000>; -- }; -- partition@1680000 { -- label = "rootfs1"; -- reg = <0x1680000 0x2fc0000>; -- }; -- partition@4640000 { -- label = "kernel_2"; -- reg = <0x4640000 0x0a00000>; -- }; -- partition@5040000 { -- label = "rootfs2"; -- reg = <0x5040000 0x2fc0000>; -+ partition@140000 { -+ label = "ubi"; -+ reg = <0x0140000 0x7ec0000>; - }; - }; - diff --git a/target/linux/kirkwood/patches-4.9/107-02-nsa310b.patch b/target/linux/kirkwood/patches-4.9/107-02-nsa310b.patch deleted file mode 100644 index faf8d891a5..0000000000 --- a/target/linux/kirkwood/patches-4.9/107-02-nsa310b.patch +++ /dev/null @@ -1,147 +0,0 @@ -kirkwood: add nsa310b dtb, a zyxel nsa310 variant - -add support to a nsa310 variant with red/green usb led -and lm85 temp/fan controller - -Signed-off-by: Alberto Bursi - -NOTE: this patch can be upstreamed as-is, LEDE-specific - nand partitions are set in another patch - ---- a/arch/arm/boot/dts/Makefile -+++ b/arch/arm/boot/dts/Makefile -@@ -238,6 +238,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ - kirkwood-ns2mini.dtb \ - kirkwood-nsa310.dtb \ - kirkwood-nsa310a.dtb \ -+ kirkwood-nsa310b.dtb \ - kirkwood-nsa320.dtb \ - kirkwood-nsa325.dtb \ - kirkwood-openblocks_a6.dtb \ ---- /dev/null -+++ b/arch/arm/boot/dts/kirkwood-nsa310b.dts -@@ -0,0 +1,124 @@ -+/dts-v1/; -+ -+#include "kirkwood-nsa3x0-common.dtsi" -+ -+/* -+ * There are at least two different NSA310 designs. This variant has -+ * a red/green USB Led (same as nsa310) and a lm85 temp/fan controller. -+ */ -+ -+/ { -+ model = "ZyXEL NSA310b"; -+ compatible = "zyxel,nsa310b", "zyxel,nsa310", "marvell,kirkwood-88f6281", "marvell,kirkwood"; -+ -+ memory { -+ device_type = "memory"; -+ reg = <0x00000000 0x10000000>; -+ }; -+ -+ chosen { -+ bootargs = "console=ttyS0,115200"; -+ stdout-path = &uart0; -+ }; -+ -+ ocp@f1000000 { -+ pinctrl: pin-controller@10000 { -+ pinctrl-names = "default"; -+ -+ pmx_led_esata_green: pmx-led-esata-green { -+ marvell,pins = "mpp12"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_esata_red: pmx-led-esata-red { -+ marvell,pins = "mpp13"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_usb_green: pmx-led-usb-green { -+ marvell,pins = "mpp15"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_usb_red: pmx-led-usb-red { -+ marvell,pins = "mpp16"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_sys_green: pmx-led-sys-green { -+ marvell,pins = "mpp28"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_sys_red: pmx-led-sys-red { -+ marvell,pins = "mpp29"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_hdd_green: pmx-led-hdd-green { -+ marvell,pins = "mpp41"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_hdd_red: pmx-led-hdd-red { -+ marvell,pins = "mpp42"; -+ marvell,function = "gpio"; -+ }; -+ -+ }; -+ -+ i2c@11000 { -+ status = "okay"; -+ -+ lm85: lm85@2e { -+ compatible = "national,lm85"; -+ reg = <0x2e>; -+ }; -+ }; -+ }; -+ -+ gpio-leds { -+ compatible = "gpio-leds"; -+ -+ green-sys { -+ label = "nsa310:green:sys"; -+ gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; -+ }; -+ red-sys { -+ label = "nsa310:red:sys"; -+ gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>; -+ }; -+ green-hdd { -+ label = "nsa310:green:hdd"; -+ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; -+ }; -+ red-hdd { -+ label = "nsa310:red:hdd"; -+ gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; -+ }; -+ green-esata { -+ label = "nsa310:green:esata"; -+ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; -+ }; -+ red-esata { -+ label = "nsa310:red:esata"; -+ gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; -+ }; -+ green-usb { -+ label = "nsa310:green:usb"; -+ gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; -+ }; -+ red-usb { -+ label = "nsa310:red:usb"; -+ gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>; -+ }; -+ green-copy { -+ label = "nsa310:green:copy"; -+ gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; -+ }; -+ red-copy { -+ label = "nsa310:red:copy"; -+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; -+ }; -+ }; -+}; diff --git a/target/linux/kirkwood/patches-4.9/108-on100.patch b/target/linux/kirkwood/patches-4.9/108-on100.patch deleted file mode 100644 index 3cab70aaa8..0000000000 --- a/target/linux/kirkwood/patches-4.9/108-on100.patch +++ /dev/null @@ -1,173 +0,0 @@ ---- /dev/null -+++ b/arch/arm/boot/dts/kirkwood-on100.dts -@@ -0,0 +1,160 @@ -+/dts-v1/; -+ -+#include "kirkwood.dtsi" -+#include "kirkwood-6282.dtsi" -+ -+/ { -+ model = "Cisco Systems ON100"; -+ compatible = "cisco,on100", "marvell,kirkwood-88f6282", "marvell,kirkwood"; -+ -+ memory { -+ device_type = "memory"; -+ reg = <0x00000000 0x20000000>; -+ }; -+ -+ aliases { -+ serial0 = &uart0; -+ }; -+ -+ chosen { -+ bootargs = "console=ttyS0,115200n8 earlyprintk"; -+ stdout-path = "serial0:115200n8"; -+ }; -+ -+ gpio_keys { -+ compatible = "gpio-keys"; -+ #address-cells = <1>; -+ #size-cells = <0>; -+ pinctrl-0 = <&pmx_btn_reset>; -+ pinctrl-names = "default"; -+ -+ button@1 { -+ label = "Reset Button"; -+ linux,code = ; -+ gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; -+ }; -+ }; -+ -+ gpio-leds { -+ compatible = "gpio-leds"; -+ pinctrl-0 = < &pmx_led_health_r &pmx_led_health_g >; -+ pinctrl-names = "default"; -+ -+ health-g { -+ label = "on100:green:health"; -+ gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; -+ }; -+ -+ health-r { -+ label = "on100:red:health"; -+ gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; -+ }; -+ -+ health2-g { -+ label = "on100:green:health2"; -+ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; -+ }; -+ -+ health2-r { -+ label = "on100:red:health2"; -+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; -+ }; -+ }; -+}; -+ -+ð0 { -+ status = "okay"; -+ -+ ethernet0-port@0 { -+ phy-handle = <ðphy0>; -+ phy-connection-type = "rgmii-id"; -+ }; -+}; -+ -+ð1 { -+ status = "okay"; -+ -+ ethernet1-port@0 { -+ phy-handle = <ðphy1>; -+ phy-connection-type = "rgmii-id"; -+ }; -+}; -+ -+&mdio { -+ status = "okay"; -+ -+ ethphy0: ethernet-phy@0 { -+ /* Marvell 88E1121R */ -+ compatible = "ethernet-phy-id0141.0cb0", -+ "ethernet-phy-ieee802.3-c22"; -+ reg = <0>; -+ }; -+ -+ ethphy1: ethernet-phy@1 { -+ /* Marvell 88E1121R */ -+ compatible = "ethernet-phy-id0141.0cb0", -+ "ethernet-phy-ieee802.3-c22"; -+ reg = <1>; -+ }; -+}; -+ -+&nand { -+ status = "okay"; -+ -+ partition@0 { -+ label = "u-boot"; -+ reg = <0x00000000 0x000a0000>; -+ read-only; -+ }; -+ -+ partition@a0000 { -+ label = "u-boot environment"; -+ reg = <0x000a0000 0x00020000>; -+ read-only; -+ }; -+ -+ partition@c0000 { -+ label = "kernel"; -+ reg = <0x000c0000 0x00540000>; -+ }; -+ -+ partition@600000 { -+ label = "ubi"; -+ reg = <0x00600000 0x1fa00000>; -+ }; -+}; -+ -+&pinctrl { -+ pmx_led_health_r: pmx-led-health-r { -+ marvell,pins = "mpp45"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_health_g: pmx-led-health-g { -+ marvell,pins = "mpp44"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_health2_r: pmx-led-health2-r { -+ marvell,pins = "mpp47"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_health2_g: pmx-led-health2-g { -+ marvell,pins = "mpp46"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_btn_reset: pmx-led-reset { -+ marvell,pins = "mpp31"; -+ marvell,function = "gpio"; -+ }; -+}; -+ -+&sdio { -+ status = "okay"; -+}; -+ -+&uart0 { -+ status = "okay"; -+}; ---- a/arch/arm/boot/dts/Makefile -+++ b/arch/arm/boot/dts/Makefile -@@ -241,6 +241,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ - kirkwood-nsa310b.dtb \ - kirkwood-nsa320.dtb \ - kirkwood-nsa325.dtb \ -+ kirkwood-on100.dtb \ - kirkwood-openblocks_a6.dtb \ - kirkwood-openblocks_a7.dtb \ - kirkwood-openrd-base.dtb \ diff --git a/target/linux/kirkwood/patches-4.9/109-pogoplug_v4.patch b/target/linux/kirkwood/patches-4.9/109-pogoplug_v4.patch deleted file mode 100644 index dff1966d5c..0000000000 --- a/target/linux/kirkwood/patches-4.9/109-pogoplug_v4.patch +++ /dev/null @@ -1,59 +0,0 @@ ---- a/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts -+++ b/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts -@@ -23,6 +23,7 @@ - }; - - chosen { -+ bootargs = "console=ttyS0,115200"; - stdout-path = "uart0:115200n8"; - }; - -@@ -36,8 +37,8 @@ - eject { - debounce_interval = <50>; - wakeup-source; -- linux,code = ; -- label = "Eject Button"; -+ linux,code = ; -+ label = "Reset"; - gpios = <&gpio0 29 GPIO_ACTIVE_LOW>; - }; - }; -@@ -136,29 +137,19 @@ - #size-cells = <1>; - - partition@0 { -- label = "u-boot"; -- reg = <0x00000000 0x200000>; -+ label = "uboot"; -+ reg = <0x00000000 0x1c0000>; - read-only; - }; - -- partition@200000 { -- label = "uImage"; -- reg = <0x00200000 0x300000>; -- }; -- -- partition@500000 { -- label = "uImage2"; -- reg = <0x00500000 0x300000>; -+ partition@1c0000 { -+ label = "uboot_env"; -+ reg = <0x001c0000 0x40000>; - }; - -- partition@800000 { -- label = "failsafe"; -- reg = <0x00800000 0x800000>; -- }; -- -- partition@1000000 { -- label = "root"; -- reg = <0x01000000 0x7000000>; -+ partition@200000 { -+ label = "ubi"; -+ reg = <0x00200000 0x7e00000>; - }; - }; - }; diff --git a/target/linux/kirkwood/patches-4.9/200-disable-tso.patch b/target/linux/kirkwood/patches-4.9/200-disable-tso.patch deleted file mode 100644 index cde53d0218..0000000000 --- a/target/linux/kirkwood/patches-4.9/200-disable-tso.patch +++ /dev/null @@ -1,35 +0,0 @@ -From: Ezequiel Garcia -Subject: [PATCH] net: mv643xx_eth: Make TSO disabled by default - -Data corruption has been observed to be produced by TSO. For instance, -accessing files on a NFS-server with TSO enabled results in different data -transferred each time. - -This has been observed only on Kirkwood platforms, i.e. with the mv643xx_eth -driver. Same tests on platforms using the mvneta ethernet driver have -passed without errors. - -Make TSO disabled by default for now, until we can found a proper fix -for the regression. - -Fixes: 3ae8f4e0b98 ('net: mv643xx_eth: Implement software TSO') -Reported-by: Slawomir Gajzner gmail.com> -Reported-by: Julien D'Ascenzio yahoo.fr> -Signed-off-by: Ezequiel Garcia free-electrons.com> ---- ---- a/drivers/net/ethernet/marvell/mv643xx_eth.c -+++ b/drivers/net/ethernet/marvell/mv643xx_eth.c -@@ -3197,11 +3197,11 @@ static int mv643xx_eth_probe(struct plat - dev->watchdog_timeo = 2 * HZ; - dev->base_addr = 0; - -- dev->features = NETIF_F_SG | NETIF_F_IP_CSUM | NETIF_F_TSO; -+ dev->features = NETIF_F_SG | NETIF_F_IP_CSUM; - dev->vlan_features = dev->features; - - dev->features |= NETIF_F_RXCSUM; -- dev->hw_features = dev->features; -+ dev->hw_features = dev->features | NETIF_F_TSO; - - dev->priv_flags |= IFF_UNICAST_FLT; - dev->gso_max_segs = MV643XX_MAX_TSO_SEGS; diff --git a/target/linux/kirkwood/patches-4.9/201-enable-sata-port-specific-led-triggers.patch b/target/linux/kirkwood/patches-4.9/201-enable-sata-port-specific-led-triggers.patch deleted file mode 100644 index 202c9c02e6..0000000000 --- a/target/linux/kirkwood/patches-4.9/201-enable-sata-port-specific-led-triggers.patch +++ /dev/null @@ -1,10 +0,0 @@ ---- a/arch/arm/mach-mvebu/Kconfig -+++ b/arch/arm/mach-mvebu/Kconfig -@@ -117,6 +117,7 @@ config MACH_DOVE - config MACH_KIRKWOOD - bool "Marvell Kirkwood boards" - depends on ARCH_MULTI_V5 -+ select ARCH_WANT_LIBATA_LEDS - select CPU_FEROCEON - select GPIOLIB - select KIRKWOOD_CLK diff --git a/target/linux/kirkwood/patches-4.9/202-linksys-find-active-root.patch b/target/linux/kirkwood/patches-4.9/202-linksys-find-active-root.patch deleted file mode 100644 index f4156be4d1..0000000000 --- a/target/linux/kirkwood/patches-4.9/202-linksys-find-active-root.patch +++ /dev/null @@ -1,62 +0,0 @@ -The WRT1900AC among other Linksys routers uses a dual-firmware layout. -Dynamically rename the active partition to "ubi". - -Signed-off-by: Imre Kaloz ---- ---- a/drivers/mtd/ofpart.c -+++ b/drivers/mtd/ofpart.c -@@ -25,6 +25,8 @@ static bool node_has_compatible(struct d - return of_get_property(pp, "compatible", NULL); - } - -+static int mangled_rootblock; -+ - static int parse_fixed_partitions(struct mtd_info *master, - const struct mtd_partition **pparts, - struct mtd_part_parser_data *data) -@@ -32,6 +34,7 @@ static int parse_fixed_partitions(struct - struct mtd_partition *parts; - struct device_node *mtd_node; - struct device_node *ofpart_node; -+ const char *owrtpart = "ubi"; - const char *partname; - struct device_node *pp; - int nr_parts, i, ret = 0; -@@ -110,9 +113,15 @@ static int parse_fixed_partitions(struct - parts[i].size = of_read_number(reg + a_cells, s_cells); - parts[i].of_node = pp; - -- partname = of_get_property(pp, "label", &len); -- if (!partname) -- partname = of_get_property(pp, "name", &len); -+ if (mangled_rootblock && (i == mangled_rootblock)) { -+ partname = owrtpart; -+ } else { -+ partname = of_get_property(pp, "label", &len); -+ -+ if (!partname) -+ partname = of_get_property(pp, "name", &len); -+ } -+ - parts[i].name = partname; - - if (of_get_property(pp, "read-only", &len)) -@@ -220,6 +229,18 @@ static int __init ofpart_parser_init(voi - return 0; - } - -+static int __init active_root(char *str) -+{ -+ get_option(&str, &mangled_rootblock); -+ -+ if (!mangled_rootblock) -+ return 1; -+ -+ return 1; -+} -+ -+__setup("mangled_rootblock=", active_root); -+ - static void __exit ofpart_parser_exit(void) - { - deregister_mtd_parser(&ofpart_parser);