From: Alberto Bursi Date: Tue, 2 Jan 2018 14:54:07 +0000 (+0100) Subject: uboot-kirkwood: add uboot for pogoplug v4 X-Git-Url: http://git.cdn.openwrt.org/?a=commitdiff_plain;h=f5d267df638d7adc6654f4a1a3d7c7557cafd759;p=openwrt%2Fstaging%2Fadrian.git uboot-kirkwood: add uboot for pogoplug v4 add an uboot able to boot a kernel in an ubi partition This uboot also has a "recovery" feature, before booting from flash it will try to boot a initramfs image called "initramfs.bin" from a FAT32-formatted USB drive connected to the USB 2.0 port. (u-boot lacks drivers for usb 3.0 controllers) Just rename the initramfs image and place it on the usb drive, the uboot will load it. In case there is no USB drive or no such file is found, the uboot will boot from internal flash. The whole check takes less than a second, boot times are not impacted. Signed-off-by: Alberto Bursi --- diff --git a/package/boot/uboot-kirkwood/Makefile b/package/boot/uboot-kirkwood/Makefile index 2b6f00f50f..f4bb87556c 100644 --- a/package/boot/uboot-kirkwood/Makefile +++ b/package/boot/uboot-kirkwood/Makefile @@ -74,6 +74,11 @@ define U-Boot/pogo_e02_second_stage BUILD_DEVICES:=cloudengines_pogoe02 endef +define U-Boot/pogoplugv4 + NAME:=Cloud Engines Pogoplug V4 + BUILD_DEVICES:=cloudengines_pogoplugv4 +endef + UBOOT_TARGETS := \ dockstar dockstar_second_stage \ goflexhome \ @@ -81,7 +86,8 @@ UBOOT_TARGETS := \ iconnect iconnect_second_stage \ nsa310 \ nsa325 \ - pogo_e02 pogo_e02_second_stage + pogo_e02 pogo_e02_second_stage \ + pogoplugv4 define Build/Configure $(if $(findstring _second_stage,$(BUILD_VARIANT)), diff --git a/package/boot/uboot-kirkwood/patches/010-pogoplug_v4.patch b/package/boot/uboot-kirkwood/patches/010-pogoplug_v4.patch new file mode 100644 index 0000000000..d2daf0b66f --- /dev/null +++ b/package/boot/uboot-kirkwood/patches/010-pogoplug_v4.patch @@ -0,0 +1,1574 @@ +--- a/arch/arm/mach-kirkwood/Kconfig ++++ b/arch/arm/mach-kirkwood/Kconfig +@@ -25,6 +25,9 @@ config TARGET_LSXL + config TARGET_POGO_E02 + bool "pogo_e02 Board" + ++config TARGET_POGOPLUGV4 ++ bool "Pogoplug V4 Board" ++ + config TARGET_DNS325 + bool "dns325 Board" + +@@ -77,6 +80,7 @@ source "board/Marvell/guruplug/Kconfig" + source "board/Marvell/sheevaplug/Kconfig" + source "board/buffalo/lsxl/Kconfig" + source "board/cloudengines/pogo_e02/Kconfig" ++source "board/cloudengines/pogoplugv4/Kconfig" + source "board/d-link/dns325/Kconfig" + source "board/iomega/iconnect/Kconfig" + source "board/keymile/km_arm/Kconfig" +--- a/arch/arm/mach-kirkwood/include/mach/config.h ++++ b/arch/arm/mach-kirkwood/include/mach/config.h +@@ -77,6 +77,7 @@ + * Ethernet Driver configuration + */ + #ifdef CONFIG_CMD_NET ++#define CONFIG_FEATURE_COMMAND_EDITING + #define CONFIG_NETCONSOLE /* include NetConsole support */ + #define CONFIG_MII /* expose smi ove miiphy interface */ + #define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */ +@@ -110,6 +111,7 @@ + #define CONFIG_SYS_ATA_STRIDE 4 + /* Controller supports 48-bits LBA addressing */ + #define CONFIG_LBA48 ++#define CONFIG_SYS_64BIT_LBA + /* CONFIG_IDE requires some #defines for ATA registers */ + #define CONFIG_SYS_IDE_MAXBUS 2 + #define CONFIG_SYS_IDE_MAXDEVICE 2 +@@ -134,4 +136,15 @@ + #define CONFIG_SYS_TIMER_COUNTER (MVEBU_TIMER_BASE + 0x14) + #define CONFIG_SYS_TIMER_RATE CONFIG_SYS_TCLK + ++/* ++ * Boot option ++ */ ++#define CONFIG_CMD_BOOTZ ++ ++/* ++ * GPIO ++ */ ++#define CONFIG_CMD_GPIO ++#define CONFIG_KIRKWOOD_GPIO ++ + #endif /* _KW_CONFIG_H */ +--- a/arch/arm/mach-kirkwood/include/mach/kw88f6192.h ++++ b/arch/arm/mach-kirkwood/include/mach/kw88f6192.h +@@ -16,6 +16,6 @@ + #define KW_REGS_PHY_BASE KW88F6192_REGS_PHYS_BASE + + /* TCLK Core Clock defination */ +-#define CONFIG_SYS_TCLK 166000000 /* 166MHz */ ++#define CONFIG_SYS_TCLK 166666667 /* 166MHz */ + + #endif /* _CONFIG_KW88F6192_H */ +--- a/arch/arm/mach-kirkwood/include/mach/mpp.h ++++ b/arch/arm/mach-kirkwood/include/mach/mpp.h +@@ -217,10 +217,12 @@ + #define MPP33_GPIO MPP( 33, 0x0, 1, 1, 0, 1, 1, 1 ) + #define MPP33_TDM_DTX MPP( 33, 0x2, 0, 1, 0, 0, 1, 1 ) + #define MPP33_GE1_13 MPP( 33, 0x3, 0, 0, 0, 1, 1, 1 ) ++#define MPP33_SATA1_ACTn MPP( 33, 0x5, 0, 1, 0, 1, 1, 1 ) + + #define MPP34_GPIO MPP( 34, 0x0, 1, 1, 0, 1, 1, 1 ) + #define MPP34_TDM_SPI_CS1 MPP( 34, 0x2, 0, 1, 0, 0, 1, 1 ) + #define MPP34_GE1_14 MPP( 34, 0x3, 0, 0, 0, 1, 1, 1 ) ++#define MPP34_SATA1_ACTn MPP( 34, 0x5, 0, 1, 0, 1, 1, 1 ) + + #define MPP35_GPIO MPP( 35, 0x0, 1, 1, 1, 1, 1, 1 ) + #define MPP35_TDM_CH0_TX_QL MPP( 35, 0x2, 0, 1, 0, 0, 1, 1 ) +--- a/arch/arm/mach-mvebu/include/mach/soc.h ++++ b/arch/arm/mach-mvebu/include/mach/soc.h +@@ -18,6 +18,8 @@ + #define SOC_88F6810_ID 0x6810 + #define SOC_88F6820_ID 0x6820 + #define SOC_88F6828_ID 0x6828 ++#define SOC_88F6192_ID 0x6192 ++#define SOC_88F6702_ID 0x6702 + + /* A375 revisions */ + #define MV_88F67XX_A0_ID 0x3 +--- /dev/null ++++ b/board/cloudengines/pogoplugv4/Kconfig +@@ -0,0 +1,12 @@ ++if TARGET_POGOPLUGV4 ++ ++config SYS_BOARD ++ default "pogoplugv4" ++ ++config SYS_VENDOR ++ default "cloudengines" ++ ++config SYS_CONFIG_NAME ++ default "pogoplugv4" ++ ++endif +--- /dev/null ++++ b/board/cloudengines/pogoplugv4/MAINTAINERS +@@ -0,0 +1,6 @@ ++POGOPLUGV4 BOARD ++M: Alberto Bursi ++S: Maintained ++F: board/cloudengines/pogoplugv4/ ++F: include/configs/pogoplugv4.h ++F: configs/pogoplugv4_defconfig +--- /dev/null ++++ b/board/cloudengines/pogoplugv4/Makefile +@@ -0,0 +1,11 @@ ++# ++# (C) Copyright 2009 bodhi ++# ++# Based on ++# Marvell Semiconductor ++# Written-by: Prafulla Wadaskar ++# ++# SPDX-License-Identifier: GPL-2.0+ ++# ++ ++obj-y := pogoplugv4.o +--- /dev/null ++++ b/board/cloudengines/pogoplugv4/kwbimage.cfg +@@ -0,0 +1,167 @@ ++# ++# Copyright (C) 2012 ++# David Purdy ++# ++# Based on Kirkwood support: ++# (C) Copyright 2009 ++# Marvell Semiconductor ++# Written-by: Prafulla Wadaskar marvell.com> ++# ++# See file CREDITS for list of people who contributed to this ++# project. ++# ++# This program is free software; you can redistribute it and/or ++# modify it under the terms of the GNU General Public License as ++# published by the Free Software Foundation; either version 2 of ++# the License, or (at your option) any later version. ++# ++# This program is distributed in the hope that it will be useful, ++# but WITHOUT ANY WARRANTY; without even the implied warranty of ++# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++# GNU General Public License for more details. ++# ++# You should have received a copy of the GNU General Public License ++# along with this program; If not, see . ++# ++# Refer docs/README.kwimage for more details about how-to configure ++# and create kirkwood boot image ++# ++ ++# Boot Media configurations (DONE) ++BOOT_FROM nand ++NAND_ECC_MODE default ++NAND_PAGE_SIZE 0x0800 ++ ++# SOC registers configuration using bootrom header extension ++# Maximum KWBIMAGE_MAX_CONFIG configurations allowed ++ ++# Configure RGMII-0 interface pad voltage to 1.8V (SHOULD BE SAME) ++DATA 0xffd100e0 0x1b1b1b9b ++ ++#Dram initalization for SINGLE x16 CL=3 @ 200MHz (need CL=3 @ 200MHz?) ++DATA 0xffd01400 0x43000618 # DDR Configuration register ++# bit13-0: 0x200 (200 DDR2 clks refresh rate) ++# bit23-14: zero ++# bit24: 1= enable exit self refresh mode on DDR access ++# bit25: 1 required ++# bit29-26: zero ++# bit31-30: 01 ++ ++DATA 0xffd01404 0x34143000 # DDR Controller Control Low ++# bit 4: 0=addr/cmd in smame cycle ++# bit 5: 0=clk is driven during self refresh, we don't care for APX ++# bit 6: 0=use recommended falling edge of clk for addr/cmd ++# bit14: 0=input buffer always powered up ++# bit18: 1=cpu lock transaction enabled ++# bit23-20: 3=recommended value for CL=3 and STARTBURST_DEL disabled bit31=0 ++# bit27-24: 6= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM ++# bit30-28: 3 required ++# bit31: 0=no additional STARTBURST delay ++ ++DATA 0xffd01408 0x11012227 # DDR Timing (Low) (active cycles value +1) ++# bit3-0: TRAS lsbs ++# bit7-4: TRCD ++# bit11- 8: TRP ++# bit15-12: TWR ++# bit19-16: TWTR ++# bit20: TRAS msb ++# bit23-21: 0x0 ++# bit27-24: TRRD ++# bit31-28: TRTP ++ ++DATA 0xffd0140c 0x00000819 # DDR Timing (High) ++# bit6-0: TRFC ++# bit8-7: TR2R ++# bit10-9: TR2W ++# bit12-11: TW2W ++# bit31-13: zero required ++ ++DATA 0xffd01410 0x00000001 # DDR Address Control (changed to Dockstar vals) ++# bit1-0: 00, Cs0width=x16 ++# bit3-2: 10, Cs0size=512Mb ++# bit5-4: 00, Cs2width=nonexistent ++# bit7-6: 00, Cs1size =nonexistent ++# bit9-8: 00, Cs2width=nonexistent ++# bit11-10: 00, Cs2size =nonexistent ++# bit13-12: 00, Cs3width=nonexistent ++# bit15-14: 00, Cs3size =nonexistent ++# bit16: 0, Cs0AddrSel ++# bit17: 0, Cs1AddrSel ++# bit18: 0, Cs2AddrSel ++# bit19: 0, Cs3AddrSel ++# bit31-20: 0 required ++ ++DATA 0xffd01414 0x00000000 # DDR Open Pages Control ++# bit0: 0, OpenPage enabled ++# bit31-1: 0 required ++ ++DATA 0xffd01418 0x00000000 # DDR Operation ++# bit3-0: 0x0, DDR cmd ++# bit31-4: 0 required ++ ++DATA 0xffd0141c 0x00000632 # DDR Mode ++# bit2-0: 2, BurstLen=2 required ++# bit3: 0, BurstType=0 required ++# bit6-4: 4, CL=5 (<===== change to CL=3 ?) ++# bit7: 0, TestMode=0 normal ++# bit8: 0, DLL reset=0 normal ++# bit11-9: 6, auto-precharge write recovery ???????????? ++# bit12: 0, PD must be zero ++# bit31-13: 0 required ++ ++DATA 0xffd01420 0x00000040 # DDR Extended Mode ++# bit0: 0, DDR DLL enabled ++# bit1: 0, DDR drive strenght normal ++# bit2: 0, DDR ODT control lsd (disabled) ++# bit5-3: 000, required ++# bit6: 1, DDR ODT control msb, (disabled) ++# bit9-7: 000, required ++# bit10: 0, differential DQS enabled ++# bit11: 0, required ++# bit12: 0, DDR output buffer enabled ++# bit31-13: 0 required ++ ++DATA 0xffd01424 0x0000F07F # DDR Controller Control High ++# bit2-0: 111, required ++# bit3 : 1 , MBUS Burst Chop disabled ++# bit6-4: 111, required ++# bit7 : 0 ++# bit8 : 0 , no sample stage ++# bit9 : 0 , no half clock cycle addition to dataout ++# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals ++# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh ++# bit15-12: 1111 required ++# bit31-16: 0 required ++ ++DATA 0xffd01428 0x00085520 # DDR2 ODT Read Timing (default values) ++DATA 0xffd0147c 0x00008552 # DDR2 ODT Write Timing (default values) ++ ++DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 ++DATA 0xFFD01504 0x07FFFFF1 # CS[0]n Size ++# bit0: 1, Window enabled ++# bit1: 0, Write Protect disabled ++# bit3-2: 00, CS0 hit selected ++# bit23-4: ones, required ++# bit31-24: 0x07, Size (i.e. 128MB) ++ ++DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled ++DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled ++DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled ++ ++DATA 0xffd01494 0x00030000 # DDR ODT Control (Low) (DONE) ++# bit3-0: 2, ODT0Rd, MODT[0] asserted during read from DRAM CS1 ++# bit7-4: 1, ODT0Rd, MODT[0] asserted during read from DRAM CS0 ++# bit19-16:2, ODT0Wr, MODT[0] asserted during write to DRAM CS1 ++# bit23-20:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0 ++ ++DATA 0xffd01498 0x00000000 # DDR ODT Control (High) (DONE) ++# bit1-0: 00, ODT0 controlled by ODT Control (low) register above ++# bit3-2: 01, ODT1 active NEVER! ++# bit31-4: zero, required ++ ++DATA 0xffd0149c 0x0000e803 # CPU ODT Control (DONE) ++DATA 0xffd01480 0x00000001 # DDR Initialization Control (DONE) ++#bit0=1, enable DDR init upon this register write ++ ++# End of Header extension ++DATA 0x0 0x0 +--- /dev/null ++++ b/board/cloudengines/pogoplugv4/pogoplugv4.c +@@ -0,0 +1,223 @@ ++/* ++ * Copyright (C) 2016 bodhi ++ * Copyright (C) 2014 bodhi ++ * ++ * Based on ++ * ++ * Copyright (C) 2014 ++ * ++ * Copyright (C) 2012 ++ * David Purdy ++ * ++ * Based on Kirkwood support: ++ * (C) Copyright 2009 ++ * Marvell Semiconductor ++ * Written-by: Prafulla Wadaskar ++ * ++ * See file CREDITS for list of people who contributed to this ++ * project. ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License as ++ * published by the Free Software Foundation; either version 2 of ++ * the License, or (at your option) any later version. ++ * ++ * This program is distributed in the hope that it will be useful, ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ * ++ * You should have received a copy of the GNU General Public License ++ * along with this program; If not, see . ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include "pogoplugv4.h" ++#include ++ ++#ifdef CONFIG_KIRKWOOD_MMC ++#include ++#endif /* CONFIG_KIRKWOOD_MMC */ ++ ++ ++DECLARE_GLOBAL_DATA_PTR; ++ ++int board_early_init_f(void) ++{ ++ /* ++ * default gpio configuration ++ * There are maximum 64 gpios controlled through 2 sets of registers ++ * the below configuration configures mainly initial LED status ++ */ ++ mvebu_config_gpio(POGOPLUGV4_OE_VAL_LOW, ++ POGOPLUGV4_OE_VAL_HIGH, ++ POGOPLUGV4_OE_LOW, POGOPLUGV4_OE_HIGH); ++ ++ /* Multi-Purpose Pins Functionality configuration */ ++ u32 kwmpp_config[] = { ++ MPP0_NF_IO2, ++ MPP1_NF_IO3, ++ MPP2_NF_IO4, ++ MPP3_NF_IO5, ++ MPP4_NF_IO6, ++ MPP5_NF_IO7, ++ MPP6_SYSRST_OUTn, ++ MPP7_GPO, ++ MPP8_TW_SDA, ++ MPP9_TW_SCK, ++ MPP10_UART0_TXD, ++ MPP11_UART0_RXD, ++ MPP12_SD_CLK, ++ MPP13_SD_CMD, ++ MPP14_SD_D0, ++ MPP15_SD_D1, ++ MPP16_SD_D2, ++ MPP17_SD_D3, ++ MPP18_NF_IO0, ++ MPP19_NF_IO1, ++ MPP20_SATA1_ACTn, ++ MPP21_SATA0_ACTn, ++ MPP22_GPIO, /* Green LED */ ++ MPP23_GPIO, ++ MPP24_GPIO, /* Red LED */ ++ MPP25_GPIO, ++ MPP26_GPIO, ++ MPP27_GPIO, ++ MPP28_GPIO, ++ MPP29_GPIO, /* Eject button */ ++ MPP30_GPIO, ++ MPP31_GPIO, ++ MPP32_GPIO, ++ MPP33_GPIO, ++ MPP34_GPIO, ++ MPP35_GPIO, /* FR6192 has only 36 GPIOs */ ++ 0 ++ }; ++ kirkwood_mpp_conf(kwmpp_config, NULL); ++ ++ return 0; ++} ++ ++int board_init(void) ++{ ++ /* Boot parameters address */ ++ gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; ++ ++ kw_gpio_set_valid(20, 1); ++ kw_gpio_set_valid(21, 1); ++ kw_gpio_set_valid(22, 1); ++ kw_gpio_set_valid(24, 1); ++ ++ return 0; ++} ++ ++#ifdef CONFIG_RESET_PHY_R ++/* Configure and initialize PHY */ ++void reset_phy(void) ++{ ++ u16 reg; ++ u16 devadr; ++ char *name = "egiga0"; ++ ++ if (miiphy_set_current_dev(name)) ++ return; ++ ++ /* command to read PHY dev address */ ++ if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) { ++ printf("Err..(%s) could not read PHY dev address\n", __func__); ++ return; ++ } ++ ++ /* ++ * Enable RGMII delay on Tx and Rx for CPU port ++ * Ref: sec 4.7.2 of chip datasheet ++ */ ++ miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2); ++ miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®); ++ reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL); ++ miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg); ++ miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0); ++ ++ /* reset the phy */ ++ miiphy_reset(name, devadr); ++ ++ debug("88E1116 Initialized on %s\n", name); ++} ++#endif /* CONFIG_RESET_PHY_R */ ++ ++#ifdef CONFIG_KIRKWOOD_MMC ++int board_mmc_init(bd_t *bis) ++{ ++ kw_mmc_initialize(bis); ++ return 0; ++} ++#endif /* CONFIG_KIRKWOOD_MMC */ ++ ++ ++#define GREEN_LED (1 << 22) ++#define RED_LED (1 << 24) ++#define BOTH_LEDS (GREEN_LED | RED_LED) ++#define NEITHER_LED 0 ++ ++static void set_leds(u32 leds, u32 blinking) ++{ ++ struct kwgpio_registers *r; ++ u32 oe; ++ u32 bl; ++ ++ r = (struct kwgpio_registers *)MVEBU_GPIO0_BASE; ++ oe = readl(&r->oe) | BOTH_LEDS; ++ writel(oe & ~leds, &r->oe); /* active low */ ++ bl = readl(&r->blink_en) & ~BOTH_LEDS; ++ writel(bl | blinking, &r->blink_en); ++} ++ ++void show_boot_progress(int val) ++{ ++ switch (val) { ++ case BOOTSTAGE_ID_RUN_OS: /* booting Linux */ ++ set_leds(BOTH_LEDS, NEITHER_LED); ++ break; ++ case BOOTSTAGE_ID_NET_ETH_START: /* Ethernet initialization */ ++ set_leds(GREEN_LED, GREEN_LED); ++ break; ++ default: ++ if (val < 0) /* error */ ++ set_leds(RED_LED, RED_LED); ++ break; ++ } ++} ++ ++#if defined(CONFIG_KIRKWOOD_GPIO) ++/* Return GPIO button status */ ++/* ++un-pressed: ++ gpio-29 (Eject Button ) in hi (act lo) - IRQ edge (clear ) ++pressed ++ gpio-29 (Eject Button ) in lo (act hi) - IRQ edge (clear ) ++*/ ++ ++static int ++do_read_button(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) ++{ ++ if (strcmp(argv[1], "eject") == 0) { ++ kw_gpio_set_valid(BTN_EJECT, GPIO_INPUT_OK); ++ kw_gpio_direction_input(BTN_EJECT); ++ return kw_gpio_get_value(BTN_EJECT); ++ } ++ else ++ return -1; ++} ++ ++ ++U_BOOT_CMD(button, 2, 0, do_read_button, ++ "Return GPIO button status 0=off 1=on", ++ "- button eject: test buttons states\n" ++); ++ ++#endif +--- /dev/null ++++ b/board/cloudengines/pogoplugv4/pogoplugv4.h +@@ -0,0 +1,50 @@ ++/* ++ * Copyright (C) 2016 ++ * bodhi ++ * ++ * Copyright (C) 2012 ++ * David Purdy ++ * ++ * Based on Kirkwood support: ++ * (C) Copyright 2009 ++ * Marvell Semiconductor ++ * Written-by: Prafulla Wadaskar ++ * ++ * See file CREDITS for list of people who contributed to this ++ * project. ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License as ++ * published by the Free Software Foundation; either version 2 of ++ * the License, or (at your option) any later version. ++ * ++ * This program is distributed in the hope that it will be useful, ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ * ++ * You should have received a copy of the GNU General Public License ++ * along with this program; If not, see . ++ */ ++ ++#ifndef __POGOPLUGV4_H ++#define __POGOPLUGV4_H ++ ++/* GPIO configuration */ ++#define POGOPLUGV4_OE_LOW (~(0)) ++#define POGOPLUGV4_OE_HIGH (~(0)) ++#define POGOPLUGV4_OE_VAL_LOW (1 << 29) ++#define POGOPLUGV4_OE_VAL_HIGH 0 ++ ++/* PHY related */ ++#define MV88E1116_LED_FCTRL_REG 10 ++#define MV88E1116_CPRSP_CR3_REG 21 ++#define MV88E1116_MAC_CTRL_REG 21 ++#define MV88E1116_PGADR_REG 22 ++#define MV88E1116_RGMII_TXTM_CTRL (1 << 4) ++#define MV88E1116_RGMII_RXTM_CTRL (1 << 5) ++ ++/* button */ ++#define BTN_EJECT 29 ++ ++#endif /* __POGOPLUGV4_H */ +--- /dev/null ++++ b/configs/pogoplugv4_defconfig +@@ -0,0 +1,35 @@ ++CONFIG_ARM=y ++CONFIG_KIRKWOOD=y ++CONFIG_TARGET_POGOPLUGV4=y ++CONFIG_SYS_PROMPT="pogoplugv4> " ++CONFIG_IDENT_STRING="\nPogoplug V4" ++CONFIG_BOOTDELAY=3 ++# CONFIG_CMD_IMLS is not set ++# CONFIG_CMD_FLASH is not set ++CONFIG_SYS_NS16550=y ++CONFIG_CMD_FDT=y ++CONFIG_OF_LIBFDT=y ++CONFIG_CMD_SETEXPR=y ++CONFIG_CMD_DHCP=y ++CONFIG_CMD_MII=y ++CONFIG_CMD_PING=y ++CONFIG_CMD_DNS=y ++CONFIG_CMD_SNTP=y ++CONFIG_CMD_USB=y ++CONFIG_CMD_DATE=y ++CONFIG_CMD_EXT2=y ++CONFIG_CMD_EXT4=y ++CONFIG_CMD_FAT=y ++CONFIG_CMD_JFFS2=y ++CONFIG_CMD_MTDPARTS=y ++CONFIG_CMD_ENV=y ++CONFIG_CMD_NAND=y ++CONFIG_CMD_MMC=y ++CONFIG_EFI_PARTITION=y ++CONFIG_ENV_IS_IN_NAND=y ++CONFIG_CMD_UBI=y ++CONFIG_USB=y ++CONFIG_USB_EHCI_HCD=y ++CONFIG_USB_STORAGE=y ++CONFIG_LZMA=y ++CONFIG_LZO=y +--- a/drivers/gpio/kw_gpio.c ++++ b/drivers/gpio/kw_gpio.c +@@ -148,3 +148,36 @@ void kw_gpio_set_blink(unsigned pin, int + /* Set blinking. */ + __set_blinking(pin, blink); + } ++ ++ ++/* ++ * Hooks to GENERIC_GPIO primitives ++ */ ++ ++int gpio_direction_input(unsigned pin) ++{ ++ return kw_gpio_direction_input(pin); ++} ++ ++int gpio_direction_output(unsigned pin, int value) ++{ ++ return kw_gpio_direction_output(pin, value); ++} ++ ++void gpio_set_value(unsigned pin, int value) { ++ kw_gpio_set_value(pin, value); ++} ++ ++int gpio_get_value(unsigned pin) { ++ return kw_gpio_get_value(pin); ++} ++ ++int gpio_request(unsigned gpio, const char *label) ++{ ++ return 0; ++} ++ ++int gpio_free(unsigned gpio) ++{ ++ return 0; ++} +--- a/drivers/mmc/Makefile ++++ b/drivers/mmc/Makefile +@@ -61,6 +61,7 @@ obj-$(CONFIG_MMC_SDHCI_TANGIER) += tang + obj-$(CONFIG_MMC_SDHCI_TEGRA) += tegra_mmc.o + obj-$(CONFIG_MMC_SDHCI_XENON) += xenon_sdhci.o + obj-$(CONFIG_MMC_SDHCI_ZYNQ) += zynq_sdhci.o ++obj-$(CONFIG_KIRKWOOD_MMC) += kirkwood_mmc.o + + obj-$(CONFIG_MMC_SUNXI) += sunxi_mmc.o + obj-$(CONFIG_MMC_UNIPHIER) += uniphier-sd.o +--- /dev/null ++++ b/drivers/mmc/kirkwood_mmc.c +@@ -0,0 +1,482 @@ ++/* ++ * (C) Copyright 2014 bodhi ++ * ++ * Based on ++ * ++ * (C) Copyright 2014 ++ * ++ * Based on ++ * ++ * Driver for Marvell SDIO/MMC controller ++ * ++ * (C) Copyright 2012 ++ * Marvell Semiconductor ++ * Written-by: Gérald Kerma ++ * See file CREDITS for list of people who contributed to this ++ * project. ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License as ++ * published by the Free Software Foundation; either version 2 of ++ * the License, or (at your option) any later version. ++ * ++ * This program is distributed in the hope that it will be useful, ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ * ++ * You should have received a copy of the GNU General Public License ++ * along with this program; if not, write to the Free Software ++ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, ++ * MA 02111-1307 USA ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++ ++#define DRIVER_NAME "kwsdio" ++ ++static int kw_mmc_setup_data(struct mmc_data *data) ++{ ++ u32 ctrl_reg; ++ ++#ifdef DEBUG ++ printf("%s, data %s : blocks=%d blksz=%d\n", DRIVER_NAME, ++ (data->flags & MMC_DATA_READ) ? "read" : "write", ++ data->blocks, data->blocksize); ++#endif ++ ++ /* default to maximum timeout */ ++ ctrl_reg = kwsd_read(SDIO_HOST_CTRL); ++ ctrl_reg |= SDIO_HOST_CTRL_TMOUT(SDIO_HOST_CTRL_TMOUT_MAX); ++ kwsd_write(SDIO_HOST_CTRL, ctrl_reg); ++ ++ if (data->flags & MMC_DATA_READ) { ++ kwsd_write(SDIO_SYS_ADDR_LOW,(u32)data->dest & 0xffff); ++ kwsd_write(SDIO_SYS_ADDR_HI,(u32)data->dest >> 16); ++ } else { ++ kwsd_write(SDIO_SYS_ADDR_LOW,(u32)data->src & 0xffff); ++ kwsd_write(SDIO_SYS_ADDR_HI,(u32)data->src >> 16); ++ } ++ ++ kwsd_write(SDIO_BLK_COUNT, data->blocks); ++ kwsd_write(SDIO_BLK_SIZE, data->blocksize); ++ ++ return 0; ++} ++ ++static int kw_mmc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd, struct mmc_data *data) ++{ ++ int timeout = 10; ++ int err; ++ ushort waittype = 0; ++ ushort resptype = 0; ++ ushort xfertype = 0; ++ ushort resp_indx = 0; ++ ++#ifdef CONFIG_MMC_DEBUG ++ printf("cmdidx [0x%x] resp_type[0x%x] cmdarg[0x%x]\n", cmd->cmdidx, cmd->resp_type, cmd->cmdarg); ++#endif ++ ++ udelay(10000); ++ ++#ifdef CONFIG_MMC_DEBUG ++ printf("%s: cmd %d (hw state 0x%04x)\n", DRIVER_NAME, cmd->cmdidx, kwsd_read(SDIO_HW_STATE)); ++#endif ++ ++ /* Checking if card is busy */ ++ while ((kwsd_read(SDIO_HW_STATE) & CARD_BUSY)) { ++ if (timeout == 0) { ++ printf("%s: card busy!\n", DRIVER_NAME); ++ return -1; ++ } ++ timeout--; ++ udelay(1000); ++ } ++ ++ /* Set up for a data transfer if we have one */ ++ if (data) { ++ if ((err = kw_mmc_setup_data(data))) ++ return err; ++ } ++ ++ resptype = SDIO_CMD_INDEX(cmd->cmdidx); ++ ++ /* Analyzing resptype/xfertype/waittype for the command */ ++ if (cmd->resp_type & MMC_RSP_BUSY) ++ resptype |= SDIO_CMD_RSP_48BUSY; ++ else if (cmd->resp_type & MMC_RSP_136) ++ resptype |= SDIO_CMD_RSP_136; ++ else if (cmd->resp_type & MMC_RSP_PRESENT) ++ resptype |= SDIO_CMD_RSP_48; ++ else ++ resptype |= SDIO_CMD_RSP_NONE; ++ ++ if (cmd->resp_type & MMC_RSP_CRC) ++ resptype |= SDIO_CMD_CHECK_CMDCRC; ++ ++ if (cmd->resp_type & MMC_RSP_OPCODE) ++ resptype |= SDIO_CMD_INDX_CHECK; ++ ++ if (cmd->resp_type & MMC_RSP_PRESENT) { ++ resptype |= SDIO_UNEXPECTED_RESP; ++ waittype |= SDIO_NOR_UNEXP_RSP; ++ } ++ ++ if (data) { ++ resptype |= SDIO_CMD_DATA_PRESENT | SDIO_CMD_CHECK_DATACRC16; ++ xfertype |= SDIO_XFER_MODE_HW_WR_DATA_EN; ++ if (data->flags & MMC_DATA_READ) { ++ xfertype |= SDIO_XFER_MODE_TO_HOST; ++ waittype = SDIO_NOR_DMA_INI; ++ } else ++ waittype |= SDIO_NOR_XFER_DONE; ++ } else ++ waittype |= SDIO_NOR_CMD_DONE; ++ ++ /* Setting cmd arguments */ ++ kwsd_write(SDIO_ARG_LOW, cmd->cmdarg & 0xffff); ++ kwsd_write(SDIO_ARG_HI, cmd->cmdarg >> 16); ++ ++ /* Setting Xfer mode */ ++ kwsd_write(SDIO_XFER_MODE, xfertype); ++ ++ kwsd_write(SDIO_NOR_INTR_STATUS, ~SDIO_NOR_CARD_INT); ++ kwsd_write(SDIO_ERR_INTR_STATUS, SDIO_POLL_MASK); ++ ++ /* Sending command */ ++ kwsd_write(SDIO_CMD, resptype); ++/* ++ kwsd_write(SDIO_CMD, KW_MMC_MAKE_CMD(cmd->cmdidx, resptype)); ++*/ ++ ++ kwsd_write(SDIO_NOR_INTR_EN, SDIO_POLL_MASK); ++ kwsd_write(SDIO_ERR_INTR_EN, SDIO_POLL_MASK); ++ ++ /* Waiting for completion */ ++ timeout = 1000000; ++ ++ while (!((kwsd_read(SDIO_NOR_INTR_STATUS)) & waittype)) { ++ if (kwsd_read(SDIO_NOR_INTR_STATUS) & SDIO_NOR_ERROR) { ++#ifdef DEBUG ++ printf("%s: kw_mmc_send_cmd: error! cmdidx : %d, err reg: %04x\n", DRIVER_NAME, cmd->cmdidx, ++wsd_read(SDIO_ERR_INTR_STATUS)); ++#endif ++ if (kwsd_read(SDIO_ERR_INTR_STATUS) & (SDIO_ERR_CMD_TIMEOUT | SDIO_ERR_DATA_TIMEOUT)) { ++ return -ETIMEDOUT; ++ } ++ return -ECOMM; ++ } ++ ++ timeout--; ++ udelay(1); ++ if (timeout <= 0) { ++ printf("%s: command timed out\n", DRIVER_NAME); ++ return -ETIMEDOUT; ++ } ++ } ++ ++ /* Handling response */ ++ if (cmd->resp_type & MMC_RSP_136) { ++ uint response[8]; ++ for (resp_indx = 0; resp_indx < 8; resp_indx++) ++ response[resp_indx] = kwsd_read(SDIO_RSP(resp_indx)); ++ ++ cmd->response[0] = ((response[0] & 0x03ff) << 22) | ++ ((response[1] & 0xffff) << 6) | ++ ((response[2] & 0xfc00) >> 10); ++ cmd->response[1] = ((response[2] & 0x03ff) << 22) | ++ ((response[3] & 0xffff) << 6) | ++ ((response[4] & 0xfc00) >> 10); ++ cmd->response[2] = ((response[4] & 0x03ff) << 22) | ++ ((response[5] & 0xffff) << 6) | ++ ((response[6] & 0xfc00) >> 10); ++ cmd->response[3] = ((response[6] & 0x03ff) << 22) | ++ ((response[7] & 0x3fff) << 8); ++ } else if (cmd->resp_type & MMC_RSP_PRESENT) { ++ uint response[3]; ++ for (resp_indx = 0; resp_indx < 3; resp_indx++) ++ response[resp_indx] = kwsd_read(SDIO_RSP(resp_indx)); ++ ++ cmd->response[0] = ((response[2] & 0x003f) << (8 - 8)) | ++ ((response[1] & 0xffff) << (14 - 8)) | ++ ((response[0] & 0x03ff) << (30 - 8)); ++ cmd->response[1] = ((response[0] & 0xfc00) >> 10); ++ cmd->response[2] = 0; ++ cmd->response[3] = 0; ++ } ++ ++#ifdef CONFIG_MMC_DEBUG ++ printf("%s: resp[0x%x] ", DRIVER_NAME, cmd->resp_type); ++ printf("[0x%x] ", cmd->response[0]); ++ printf("[0x%x] ", cmd->response[1]); ++ printf("[0x%x] ", cmd->response[2]); ++ printf("[0x%x] ", cmd->response[3]); ++ printf("\n"); ++#endif ++ ++ return 0; ++} ++ ++#if 0 ++/* Disable these three functions as they are not used anyway */ ++ ++static void kwsd_power_up(void) ++{ ++#ifdef DEBUG ++ printf("%s: power up\n", DRIVER_NAME); ++#endif ++ /* disable interrupts */ ++ kwsd_write(SDIO_NOR_INTR_EN, 0); ++ kwsd_write(SDIO_ERR_INTR_EN, 0); ++ ++ /* SW reset */ ++ kwsd_write(SDIO_SW_RESET, SDIO_SW_RESET_NOW); ++ ++ kwsd_write(SDIO_XFER_MODE, 0); ++ ++ /* enable status */ ++ kwsd_write(SDIO_NOR_STATUS_EN, SDIO_POLL_MASK); ++ kwsd_write(SDIO_ERR_STATUS_EN, SDIO_POLL_MASK); ++ ++ /* enable interrupts status */ ++ kwsd_write(SDIO_NOR_INTR_STATUS, SDIO_POLL_MASK); ++ kwsd_write(SDIO_ERR_INTR_STATUS, SDIO_POLL_MASK); ++} ++ ++static void kwsd_power_down(void) ++{ ++#ifdef DEBUG ++ printf("%s: power down\n", DRIVER_NAME); ++#endif ++ /* disable interrupts */ ++ kwsd_write(SDIO_NOR_INTR_EN, 0); ++ kwsd_write(SDIO_ERR_INTR_EN, 0); ++ ++ /* SW reset */ ++ kwsd_write(SDIO_SW_RESET, SDIO_SW_RESET_NOW); ++ ++ kwsd_write(SDIO_XFER_MODE, SDIO_XFER_MODE_STOP_CLK); ++ ++ /* disable status */ ++ kwsd_write(SDIO_NOR_STATUS_EN, 0); ++ kwsd_write(SDIO_ERR_STATUS_EN, 0); ++ ++ /* enable interrupts status */ ++ kwsd_write(SDIO_NOR_INTR_STATUS, SDIO_POLL_MASK); ++ kwsd_write(SDIO_ERR_INTR_STATUS, SDIO_POLL_MASK); ++} ++ ++static u32 kw_mmc_get_base_clock(void) ++{ ++ /* Original version did a check for board device id and revision id ++ * and assigned one of these clocks: ++ * KW_MMC_BASE_FAST_CLK_100 (revid == 0 && devid != MV88F6282_DEV_ID) ++ * KW_MMC_BASE_FAST_CLK_200 (revid != 0 || devid == MV88F6282_DEV_ID) ++ * However, this check was disabled and ++ * KW_MMC_BASE_FAST_CLOCK ++ * was returned in every case. ++ * Therefore, all of the dead logic was removed. */ ++ return KW_MMC_BASE_FAST_CLOCK; ++} ++#endif /* #if 0 */ ++ ++static inline u32 kw_mmc_get_base_clock(void) ++{ ++ /* get MMC base clock. If any logic other than just returning ++ * a fixed value is ever used, remove inline modifier. */ ++ ++ /* Possible values: ++ * - KW_MMC_BASE_FAST_CLOCK (166 MHz) ++ * - KW_MMC_BASE_FAST_CLK_100 (100 MHz) ++ * - KW_MMC_BASE_FAST_CLK_200 (200 MHz) ++ * ++ * Tests have shown that 200 MHz is more reliable than ++ * 166 MHz, so this value is used. */ ++ return KW_MMC_BASE_FAST_CLK_200; ++} ++ ++static void kw_mmc_set_clk(unsigned int clock) ++{ ++ unsigned int m; ++ ++ if (clock == 0) { ++#ifdef DEBUG ++ printf("%s: clock off\n", DRIVER_NAME); ++#endif ++ kwsd_write(SDIO_XFER_MODE, SDIO_XFER_MODE_STOP_CLK); ++ kwsd_write(SDIO_CLK_DIV, KW_MMC_BASE_DIV_MAX); ++ } else { ++ m = kw_mmc_get_base_clock() / (2 * clock) - 1; ++ if (m > KW_MMC_BASE_DIV_MAX) ++ m = KW_MMC_BASE_DIV_MAX; ++#ifdef DEBUG ++ printf("%s: kw_mmc_set_clk: base = %d dividor = 0x%x clock=%d\n", DRIVER_NAME, ++w_mmc_get_base_clock(), m, clock); ++#endif ++ kwsd_write(SDIO_CLK_DIV, m & KW_MMC_BASE_DIV_MAX); ++ } ++ udelay(10000); ++} ++ ++static void kw_mmc_set_bus(unsigned int bus) ++{ ++ u32 ctrl_reg = 0; ++ ++ ctrl_reg = kwsd_read(SDIO_HOST_CTRL); ++ ctrl_reg &= ~SDIO_HOST_CTRL_DATA_WIDTH_4_BITS; ++ ++ switch (bus) { ++ case 4: ++ ctrl_reg |= SDIO_HOST_CTRL_DATA_WIDTH_4_BITS; ++ break; ++ case 1: ++ default: ++ ctrl_reg |= SDIO_HOST_CTRL_DATA_WIDTH_1_BIT; ++ } ++ /* default transfer mode */ ++ ctrl_reg |= SDIO_HOST_CTRL_BIG_ENDIAN; ++ ctrl_reg &= ~SDIO_HOST_CTRL_LSB_FIRST; ++ ++ /* default to maximum timeout */ ++ ctrl_reg |= SDIO_HOST_CTRL_TMOUT(SDIO_HOST_CTRL_TMOUT_MAX); ++ ++ ctrl_reg |= SDIO_HOST_CTRL_PUSH_PULL_EN; ++ ++ ctrl_reg |= SDIO_HOST_CTRL_CARD_TYPE_MEM_ONLY; ++ ++ /* ++ * The HI_SPEED_EN bit is causing trouble with many (but not all) ++ * high speed SD, SDHC and SDIO cards. Not enabling that bit ++ * makes all cards work. So let's just ignore that bit for now ++ * and revisit this issue if problems for not enabling this bit ++ * are ever reported. ++ */ ++#if 0 ++ if (ios->timing == MMC_TIMING_MMC_HS || ++ ios->timing == MMC_TIMING_SD_HS) ++ ctrl_reg |= SDIO_HOST_CTRL_HI_SPEED_EN; ++#endif ++ ++#ifdef DEBUG ++ printf("%s: ctrl 0x%04x: %s %s %s\n", DRIVER_NAME, ctrl_reg, ++ (ctrl_reg & SDIO_HOST_CTRL_PUSH_PULL_EN) ? ++ "push-pull" : "open-drain", ++ (ctrl_reg & SDIO_HOST_CTRL_DATA_WIDTH_4_BITS) ? ++ "4bit-width" : "1bit-width", ++ (ctrl_reg & SDIO_HOST_CTRL_HI_SPEED_EN) ? ++ "high-speed" : ""); ++#endif ++ ++ kwsd_write(SDIO_HOST_CTRL, ctrl_reg); ++ udelay(10000); ++} ++ ++static void kw_mmc_set_ios(struct mmc *mmc) ++{ ++#ifdef DEBUG ++ printf("%s: bus[%d] clock[%d]\n", DRIVER_NAME, mmc->bus_width, mmc->clock); ++#endif ++ kw_mmc_set_bus(mmc->bus_width); ++ kw_mmc_set_clk(mmc->clock); ++} ++ ++static int kw_mmc_init(struct mmc *mmc) ++{ ++#ifdef DEBUG ++ printf("%s: kw_mmc_init\n", DRIVER_NAME); ++#endif ++ ++ /* ++ * Setting host parameters ++ * Initial Host Ctrl : Timeout : max , Normal Speed mode, 4-bit data mode ++ * Big Endian, SD memory Card, Push_pull CMD Line ++ */ ++ kwsd_write(SDIO_HOST_CTRL, ++ SDIO_HOST_CTRL_TMOUT(SDIO_HOST_CTRL_TMOUT_MAX) | ++ SDIO_HOST_CTRL_DATA_WIDTH_4_BITS | ++ SDIO_HOST_CTRL_BIG_ENDIAN | ++ SDIO_HOST_CTRL_PUSH_PULL_EN | ++ SDIO_HOST_CTRL_CARD_TYPE_MEM_ONLY); ++ ++ kwsd_write(SDIO_CLK_CTRL, 0); ++ ++ /* enable status */ ++ kwsd_write(SDIO_NOR_STATUS_EN, SDIO_POLL_MASK); ++ kwsd_write(SDIO_ERR_STATUS_EN, SDIO_POLL_MASK); ++ ++ /* disable interrupts */ ++ kwsd_write(SDIO_NOR_INTR_EN, 0); ++ kwsd_write(SDIO_ERR_INTR_EN, 0); ++ ++ /* SW reset */ ++ kwsd_write(SDIO_SW_RESET, SDIO_SW_RESET_NOW); ++ ++ udelay(10000); ++ return 0; ++} ++ ++int kw_mmc_initialize(bd_t *bis) ++{ ++ struct mmc *mmc = NULL; ++ struct mmc_config *cfg = NULL; ++ struct mmc_ops *ops = NULL; ++ char *name = NULL; ++ ++#ifdef DEBUG ++ printf("%s: %s base_clock = %d\n", DRIVER_NAME, kirkwood_id(), kw_mmc_get_base_clock()); ++#endif ++ mmc = malloc(sizeof(struct mmc)); ++ if (!mmc) ++ return -1; ++ memset(mmc, 0, sizeof(*mmc)); ++ ++ cfg = malloc(sizeof(*cfg)); ++ if (cfg == NULL) ++ return -1; ++ memset(cfg, 0, sizeof(*cfg)); ++ mmc->cfg = cfg; /* provided configuration */ ++ ++ ops = malloc(sizeof(*ops)); ++ if (ops == NULL) ++ return -1; ++ memset(ops, 0, sizeof(*ops)); ++ cfg->ops = ops; ++ ++ name = malloc(sizeof(DRIVER_NAME)+1); ++ if (name == NULL) ++ return -1; ++ cfg->name = name; ++ ++ sprintf(cfg->name, DRIVER_NAME); ++ ++ ops->send_cmd = kw_mmc_send_cmd; ++ ops->set_ios = kw_mmc_set_ios; ++ ops->init = kw_mmc_init; ++ ++ cfg->voltages = MMC_VDD_32_33 | MMC_VDD_33_34; ++ cfg->host_caps = MMC_MODE_4BIT | MMC_MODE_HS; ++ ++ cfg->f_min = kw_mmc_get_base_clock()/KW_MMC_BASE_DIV_MAX; ++ cfg->f_max = KW_MMC_CLOCKRATE_MAX; ++ cfg->b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT; ++ ++ mmc = mmc_create (cfg, NULL); ++ ++ if (mmc == NULL) { ++ free(name); ++ free(ops); ++ free(cfg); ++ printf("\nFailed to Initialize MMC\n"); ++ return -1; ++ } ++ ++ return 0; ++} +--- a/include/configs/mv-common.h ++++ b/include/configs/mv-common.h +@@ -130,4 +130,16 @@ + #define CONFIG_MTD_PARTITIONS + #endif + ++/* ++ * Kirkwood MMC ++ */ ++#if defined(CONFIG_KIRKWOOD) && defined(CONFIG_CMD_MMC) ++#define CONFIG_SYS_MMC_BASE KW_SDIO_BASE ++#endif /* defined(CONFIG_KIRKWOOD) && defined(CONFIG_CMD_MMC) */ ++ ++/* ++ * GPIO command for all Kirkwood boxes ++ */ ++#define CONFIG_CMD_GPIO ++ + #endif /* _MV_COMMON_H */ +--- /dev/null ++++ b/include/configs/pogoplugv4.h +@@ -0,0 +1,132 @@ ++/* ++ * Copyright (C) 2014-2016 bodhi ++ * Based on ++ * ++ * Copyright (C) 2012 ++ * David Purdy ++ * ++ * Based on Kirkwood support: ++ * (C) Copyright 2009 ++ * Marvell Semiconductor ++ * Written-by: Prafulla Wadaskar ++ * ++ * See file CREDITS for list of people who contributed to this ++ * project. ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License as ++ * published by the Free Software Foundation; either version 2 of ++ * the License, or (at your option) any later version. ++ * ++ * This program is distributed in the hope that it will be useful, ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ * ++ * You should have received a copy of the GNU General Public License ++ * along with this program; If not, see . ++ */ ++ ++#ifndef _CONFIG_POGOPLUGV4_H ++#define _CONFIG_POGOPLUGV4_H ++ ++/* ++ * Machine type definition and ID ++ */ ++#define MACH_TYPE_POGOPLUGV4 3960 ++#define CONFIG_MACH_TYPE MACH_TYPE_POGOPLUGV4 ++ ++/* ++ * High Level Configuration Options (easy to change) ++ */ ++#define CONFIG_FEROCEON_88FR131 /* #define CPU Core subversion */ ++#define CONFIG_KW88F6192 /* SOC Name */ ++#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ ++ ++/* ++ * Commands configuration ++ */ ++ ++#define CONFIG_SYS_LONGHELP ++#define CONFIG_PREBOOT ++ ++/* ++ * mv-common.h should be defined after CMD configs since it used them ++ * to enable certain macros ++ */ ++#include "mv-common.h" ++ ++/* ++ * Environment variables configurations ++ */ ++#ifdef CONFIG_CMD_NAND ++ ++#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */ ++ ++ ++#endif ++ ++#define CONFIG_ENV_SIZE 0x20000 /* 128k */ ++#define CONFIG_ENV_ADDR 0x1c0000 ++#define CONFIG_ENV_OFFSET 0x1c0000 /* env starts here */ ++ ++/* ++ * Default environment variables ++ */ ++#define CONFIG_BOOTCOMMAND \ ++ "usb reset ; " \ ++ "fatload usb 0:1 0x2000000 initramfs.bin ; "\ ++ "bootm 0x2000000 ; " \ ++ "ubi part ubi; " \ ++ "ubi read 0x800000 kernel; " \ ++ "bootm 0x800000" ++ ++#define CONFIG_MTDPARTS \ ++ "mtdparts=orion_nand:" \ ++ "0x1c0000(uboot)," \ ++ "0x40000(uboot_env)," \ ++ "0x7e00000(ubi)\0" ++ ++#define CONFIG_EXTRA_ENV_SETTINGS \ ++ "console=console=ttyS0,115200\0" \ ++ "mtdids=nand0=orion_nand\0" \ ++ "mtdparts="CONFIG_MTDPARTS \ ++ "bootargs_root=\0" ++ ++/* ++ * Ethernet Driver configuration ++ */ ++#ifdef CONFIG_CMD_NET ++#define CONFIG_NETCONSOLE ++#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ ++#define CONFIG_PHY_BASE_ADR 0 ++#endif /* CONFIG_CMD_NET */ ++ ++/* ++ * File system ++ */ ++#define CONFIG_JFFS2_NAND ++#define CONFIG_JFFS2_LZO ++#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ ++#define CONFIG_MTD_PARTITIONS ++ ++/* ++ * SATA ++ */ ++#ifdef CONFIG_MVSATA_IDE ++#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET ++#endif ++ ++/* ++ * Date Time ++ */ ++#ifdef CONFIG_CMD_DATE ++#define CONFIG_RTC_MV ++#endif /* CONFIG_CMD_DATE */ ++ ++/* ++ * Kirkwood GPIO ++ */ ++#define CONFIG_KIRKWOOD_GPIO ++ ++#endif /* _CONFIG_POGOPLUGV4_H */ +--- /dev/null ++++ b/include/kirkwood_mmc.h +@@ -0,0 +1,268 @@ ++/* ++ * (C) Copyright 2014 ++ * ++ * Based on ++ * ++ * (C) Copyright 2012 ++ * Marvell Semiconductor ++ * Written-by: Gérald Kerma ++ * See file CREDITS for list of people who contributed to this ++ * project. ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License as ++ * published by the Free Software Foundation; either version 2 of ++ * the License, or (at your option) any later version. ++ * ++ * This program is distributed in the hope that it will be useful, ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ * ++ * You should have received a copy of the GNU General Public License ++ * along with this program; if not, write to the Free Software ++ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, ++ * MA 02111-1307 USA ++ */ ++ ++#ifndef __KIRKWOOD_MMC_H__ ++#define __KIRKWOOD_MMC_H__ ++ ++/* ++ * Clock rates ++ */ ++ ++#define KW_MMC_CLOCKRATE_MAX 50000000 ++#define KW_MMC_BASE_DIV_MAX 0x7ff ++#define KW_MMC_BASE_FAST_CLOCK CONFIG_SYS_TCLK ++#define KW_MMC_BASE_FAST_CLK_100 100000000 ++#define KW_MMC_BASE_FAST_CLK_200 200000000 ++ ++/* ++ * Macros ++ */ ++#define kwsd_write(offs, val) writel(val, CONFIG_SYS_MMC_BASE + (offs)) ++#define kwsd_read(offs) readl(CONFIG_SYS_MMC_BASE + (offs)) ++ ++#define KW_MMC_MAKE_CMD(c, f) (((c & 0xff) << 8) | (f & 0xff)) ++ ++/* SDIO register */ ++#define SDIO_SYS_ADDR_LOW 0x000 ++#define SDIO_SYS_ADDR_HI 0x004 ++#define SDIO_BLK_SIZE 0x008 ++#define SDIO_BLK_COUNT 0x00c ++#define SDIO_ARG_LOW 0x010 ++#define SDIO_ARG_HI 0x014 ++#define SDIO_XFER_MODE 0x018 ++#define SDIO_CMD 0x01c ++#define SDIO_RSP(i) (0x020 + ((i)<<2)) ++#define SDIO_RSP0 0x020 ++#define SDIO_RSP1 0x024 ++#define SDIO_RSP2 0x028 ++#define SDIO_RSP3 0x02c ++#define SDIO_RSP4 0x030 ++#define SDIO_RSP5 0x034 ++#define SDIO_RSP6 0x038 ++#define SDIO_RSP7 0x03c ++#define SDIO_BUF_DATA_PORT 0x040 ++#define SDIO_RSVED 0x044 ++#define SDIO_HW_STATE 0x048 ++#define SDIO_PRESENT_STATE0 0x048 ++#define SDIO_PRESENT_STATE1 0x04c ++#define SDIO_HOST_CTRL 0x050 ++#define SDIO_BLK_GAP_CTRL 0x054 ++#define SDIO_CLK_CTRL 0x058 ++#define SDIO_SW_RESET 0x05c ++#define SDIO_NOR_INTR_STATUS 0x060 ++#define SDIO_ERR_INTR_STATUS 0x064 ++#define SDIO_NOR_STATUS_EN 0x068 ++#define SDIO_ERR_STATUS_EN 0x06c ++#define SDIO_NOR_INTR_EN 0x070 ++#define SDIO_ERR_INTR_EN 0x074 ++#define SDIO_AUTOCMD12_ERR_STATUS 0x078 ++#define SDIO_CURR_BYTE_LEFT 0x07c ++#define SDIO_CURR_BLK_LEFT 0x080 ++#define SDIO_AUTOCMD12_ARG_LOW 0x084 ++#define SDIO_AUTOCMD12_ARG_HI 0x088 ++#define SDIO_AUTOCMD12_INDEX 0x08c ++#define SDIO_AUTO_RSP(i) (0x090 + ((i)<<2)) ++#define SDIO_AUTO_RSP0 0x090 ++#define SDIO_AUTO_RSP1 0x094 ++#define SDIO_AUTO_RSP2 0x098 ++#define SDIO_CLK_DIV 0x128 ++ ++#define WINDOW_CTRL(i) (0x108 + ((i) << 3)) ++#define WINDOW_BASE(i) (0x10c + ((i) << 3)) ++ ++/* SDIO_PRESENT_STATE */ ++#define CARD_BUSY (1 << 1) ++#define CMD_INHIBIT (1 << 0) ++#define CMD_TXACTIVE (1 << 8) ++#define CMD_RXACTIVE (1 << 9) ++#define CMD_AUTOCMD12ACTIVE (1 << 14) ++#define CMD_BUS_BUSY (CMD_AUTOCMD12ACTIVE | \ ++ CMD_RXACTIVE | \ ++ CMD_TXACTIVE | \ ++ CMD_INHIBIT | \ ++ CARD_BUSY) ++ ++/* ++ * SDIO_CMD ++ */ ++ ++#define SDIO_CMD_RSP_NONE (0 << 0) ++#define SDIO_CMD_RSP_136 (1 << 0) ++#define SDIO_CMD_RSP_48 (2 << 0) ++#define SDIO_CMD_RSP_48BUSY (3 << 0) ++ ++#define SDIO_CMD_CHECK_DATACRC16 (1 << 2) ++#define SDIO_CMD_CHECK_CMDCRC (1 << 3) ++#define SDIO_CMD_INDX_CHECK (1 << 4) ++#define SDIO_CMD_DATA_PRESENT (1 << 5) ++#define SDIO_UNEXPECTED_RESP (1 << 7) ++ ++#define SDIO_CMD_INDEX(x) ((x) << 8) ++ ++/* ++ * SDIO_XFER_MODE ++ */ ++ ++#define SDIO_XFER_MODE_STOP_CLK (1 << 5) ++#define SDIO_XFER_MODE_HW_WR_DATA_EN (1 << 1) ++#define SDIO_XFER_MODE_AUTO_CMD12 (1 << 2) ++#define SDIO_XFER_MODE_INT_CHK_EN (1 << 3) ++#define SDIO_XFER_MODE_TO_HOST (1 << 4) ++#define SDIO_XFER_MODE_DMA (0 << 6) ++ ++/* ++ * SDIO_HOST_CTRL ++ */ ++ ++#define SDIO_HOST_CTRL_PUSH_PULL_EN (1 << 0) ++ ++#define SDIO_HOST_CTRL_CARD_TYPE_MEM_ONLY (0 << 1) ++#define SDIO_HOST_CTRL_CARD_TYPE_IO_ONLY (1 << 1) ++#define SDIO_HOST_CTRL_CARD_TYPE_IO_MEM_COMBO (2 << 1) ++#define SDIO_HOST_CTRL_CARD_TYPE_IO_MMC (3 << 1) ++#define SDIO_HOST_CTRL_CARD_TYPE_MASK (3 << 1) ++ ++#define SDIO_HOST_CTRL_BIG_ENDIAN (1 << 3) ++#define SDIO_HOST_CTRL_LSB_FIRST (1 << 4) ++#define SDIO_HOST_CTRL_DATA_WIDTH_1_BIT (0 << 9) ++#define SDIO_HOST_CTRL_DATA_WIDTH_4_BITS (1 << 9) ++#define SDIO_HOST_CTRL_HI_SPEED_EN (1 << 10) ++ ++#define SDIO_HOST_CTRL_TMOUT_MAX 0xf ++#define SDIO_HOST_CTRL_TMOUT_MASK (0xf << 11) ++#define SDIO_HOST_CTRL_TMOUT(x) ((x) << 11) ++#define SDIO_HOST_CTRL_TMOUT_EN (1 << 15) ++ ++/* ++ * SDIO_SW_RESET ++ */ ++ ++#define SDIO_SW_RESET_NOW (1 << 8) ++ ++/* ++ * Normal interrupt status bits ++ */ ++ ++#define SDIO_NOR_ERROR (1 << 15) ++#define SDIO_NOR_UNEXP_RSP (1 << 14) ++#define SDIO_NOR_AUTOCMD12_DONE (1 << 13) ++#define SDIO_NOR_SUSPEND_ON (1 << 12) ++#define SDIO_NOR_LMB_FF_8W_AVAIL (1 << 11) ++#define SDIO_NOR_LMB_FF_8W_FILLED (1 << 10) ++#define SDIO_NOR_READ_WAIT_ON (1 << 9) ++#define SDIO_NOR_CARD_INT (1 << 8) ++#define SDIO_NOR_READ_READY (1 << 5) ++#define SDIO_NOR_WRITE_READY (1 << 4) ++#define SDIO_NOR_DMA_INI (1 << 3) ++#define SDIO_NOR_BLK_GAP_EVT (1 << 2) ++#define SDIO_NOR_XFER_DONE (1 << 1) ++#define SDIO_NOR_CMD_DONE (1 << 0) ++ ++/* ++ * Error status bits ++ */ ++ ++#define SDIO_ERR_CRC_STATUS (1 << 14) ++#define SDIO_ERR_CRC_STARTBIT (1 << 13) ++#define SDIO_ERR_CRC_ENDBIT (1 << 12) ++#define SDIO_ERR_RESP_TBIT (1 << 11) ++#define SDIO_ERR_XFER_SIZE (1 << 10) ++#define SDIO_ERR_CMD_STARTBIT (1 << 9) ++#define SDIO_ERR_AUTOCMD12 (1 << 8) ++#define SDIO_ERR_DATA_ENDBIT (1 << 6) ++#define SDIO_ERR_DATA_CRC (1 << 5) ++#define SDIO_ERR_DATA_TIMEOUT (1 << 4) ++#define SDIO_ERR_CMD_INDEX (1 << 3) ++#define SDIO_ERR_CMD_ENDBIT (1 << 2) ++#define SDIO_ERR_CMD_CRC (1 << 1) ++#define SDIO_ERR_CMD_TIMEOUT (1 << 0) ++#define SDIO_POLL_MASK 0xffff /* enable all for polling */ ++ ++#define MMC_BLOCK_SIZE 512 ++ ++/* ++ * CMD12 error status bits ++ */ ++ ++#define SDIO_AUTOCMD12_ERR_NOTEXE (1 << 0) ++#define SDIO_AUTOCMD12_ERR_TIMEOUT (1 << 1) ++#define SDIO_AUTOCMD12_ERR_CRC (1 << 2) ++#define SDIO_AUTOCMD12_ERR_ENDBIT (1 << 3) ++#define SDIO_AUTOCMD12_ERR_INDEX (1 << 4) ++#define SDIO_AUTOCMD12_ERR_RESP_T_BIT (1 << 5) ++#define SDIO_AUTOCMD12_ERR_RESP_STARTBIT (1 << 6) ++ ++#define MMC_RSP_PRESENT (1 << 0) ++#define MMC_RSP_136 (1 << 1) /* 136 bit response */ ++#define MMC_RSP_CRC (1 << 2) /* expect valid crc */ ++#define MMC_RSP_BUSY (1 << 3) /* card may send busy */ ++#define MMC_RSP_OPCODE (1 << 4) /* response contains opcode */ ++ ++#define MMC_BUSMODE_OPENDRAIN 1 ++#define MMC_BUSMODE_PUSHPULL 2 ++ ++#define MMC_BUS_WIDTH_1 0 ++#define MMC_BUS_WIDTH_4 2 ++#define MMC_BUS_WIDTH_8 3 ++ ++#define MMC_CAP_4_BIT_DATA (1 << 0) /* Can the host do 4 bit transfers */ ++#define MMC_CAP_MMC_HIGHSPEED (1 << 1) /* Can do MMC high-speed timing */ ++#define MMC_CAP_SD_HIGHSPEED (1 << 2) /* Can do SD high-speed timing */ ++#define MMC_CAP_SDIO_IRQ (1 << 3) /* Can signal pending SDIO IRQs */ ++#define MMC_CAP_SPI (1 << 4) /* Talks only SPI protocols */ ++#define MMC_CAP_NEEDS_POLL (1 << 5) /* Needs polling for card-detection */ ++#define MMC_CAP_8_BIT_DATA (1 << 6) /* Can the host do 8 bit transfers */ ++ ++#define MMC_CAP_NONREMOVABLE (1 << 8) /* Nonremovable e.g. eMMC */ ++#define MMC_CAP_WAIT_WHILE_BUSY (1 << 9) /* Waits while card is busy */ ++#define MMC_CAP_ERASE (1 << 10) /* Allow erase/trim commands */ ++#define MMC_CAP_1_8V_DDR (1 << 11) /* can support */ ++ /* DDR mode at 1.8V */ ++#define MMC_CAP_1_2V_DDR (1 << 12) /* can support */ ++ /* DDR mode at 1.2V */ ++#define MMC_CAP_POWER_OFF_CARD (1 << 13) /* Can power off after boot */ ++#define MMC_CAP_BUS_WIDTH_TEST (1 << 14) /* CMD14/CMD19 bus width ok */ ++#define MMC_CAP_UHS_SDR12 (1 << 15) /* Host supports UHS SDR12 mode */ ++#define MMC_CAP_UHS_SDR25 (1 << 16) /* Host supports UHS SDR25 mode */ ++#define MMC_CAP_UHS_SDR50 (1 << 17) /* Host supports UHS SDR50 mode */ ++#define MMC_CAP_UHS_SDR104 (1 << 18) /* Host supports UHS SDR104 mode */ ++#define MMC_CAP_UHS_DDR50 (1 << 19) /* Host supports UHS DDR50 mode */ ++#define MMC_CAP_DRIVER_TYPE_A (1 << 23) /* Host supports Driver Type A */ ++#define MMC_CAP_DRIVER_TYPE_C (1 << 24) /* Host supports Driver Type C */ ++#define MMC_CAP_DRIVER_TYPE_D (1 << 25) /* Host supports Driver Type D */ ++#define MMC_CAP_CMD23 (1 << 30) /* CMD23 supported. */ ++#define MMC_CAP_HW_RESET (1 << 31) /* Hardware reset */ ++ ++/* ++ * Functions prototypes ++ * ++ * Original patch had static function declarations in this header file. ++ * Those should rather not be declared in the header as they only cause compiler warnings. ++ */ ++int kw_mmc_initialize(bd_t *bis); ++ ++#endif /* __KIRKWOOD_MMC_H__ */