rpcd: update to Git HEAD (2024-12-02)

cc9a471c32e1 rpc-sys: rework packagelist call for apk

Link: https://github.com/openwrt/openwrt/pull/17144
Signed-off-by: Robert Marko <robimarko@gmail.com>

netifd: check if /sbin/wifi exists before calling it

Avoid harmless error from network script by checking presence of
now-optional wifi support script, most notably confusing users of x86
snapshots.

Fixes: #14964
Signed-off-by: Andris PE <neandris@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14986
Signed-off-by: Robert Marko <robimarko@gmail.com>

ath79: remove wmac mac address defaults

1002 and 5006 are default addresses as part of the calibration data.
Don't bother specifying them explicitly.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17082
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ath79: add support for KuWFi N650 CPE

The KuWFi N650 is a 5GHz outdoor wireless bridge based on QCA9563.

Specs
=====

CPU: QCA9563, 775MHz
RAM: 128MiB
Flash: 16MiB
Wireless: QCA9888 (5GHz only)
Ethernet: 2x GBit (via QCA8337), 48V passive PoE

Installation
============

From OEM firmware
-----------------

The OEM firmware has telnet enabled by default. If not, it can be enabled
from the firmware web interface. You need a TFTP server on your computer
and the OpenWrt factory image should be available as "n650factory.bin".
It is assumed that your computer has the IP 192.168.1.1 and the N650
192.168.1.20 (default IP address).

1. Connect via Telnet to the device and log in with the default credentials
   "admin:admin"
2. Exploit the limited interface by typing "ps & /bin/sh"
3. Press <ENTER> to start the shell
4. Enter the following commands:

$ cd /tmp
$ tftp -r n650factory.bin -g 192.168.1.1
$ cat << EOF > /tmp/openwrt.sh
#!/bin/sh

IMAGE_NAME="\$1"

if [ ! -e \${IMAGE_NAME} ]; then
  echo "Image file not found: \${IMAGE_NAME}"
  exit 1
fi

. /usr/sbin/common.sh

kill_remaining TERM
sleep 3
kill_remaining KILL

run_ramfs mtd write \${IMAGE_NAME} firmware
sleep 2
reboot -f
EOF

$ chmod +x /tmp/openwrt.sh
$ /tmp/openwrt.sh n650factory.bin

Once the device reboots, it should load OpenWrt.

From UART
---------

UART installation is possible since the serial header is already soldered
on. The pinout is GND - Tx - Rx - VCC from top to bottom (RJ45 ports are
at the bottom). Connect with 115200 8N1.

First, boot OpenWrt from TFTP. Enter the following commands in the U-Boot
shell, assuming your computer has the IP address 192.168.1.1 and a TFTP
server running where the initramfs image is provided as n650.bin:

  setenv ipaddr 192.168.1.20
  setenv serverip 192.168.1.1
  tftpboot 0x84000000 n650.bin
  bootm

Once booted, transfer -loader.bin and -sysupgrade.bin images to the device
at /tmp. Enter the following commands, replacing the filenames:

  mtd write /tmp/loader.bin loader
  sysupgrade /tmp/sysupgrade.bin

Reboot and OpenWrt should load from flash.

Back to Stock
-------------

Back to stock is only possible if you saved a partition backup before
installing OpenWrt. Assuming you have fullbackup.bin covering the whole
flash, you need to prepare the image as follows:

$ dd if=fullbackup.bin of=fwconcat0.bin bs=65536 skip=4 count=212
$ dd if=fullbackup.bin of=loader.bin bs=65536 skip=216 count=1
$ dd if=fullbackup.bin of=fwconcat1.bin bs=65536 skip=217 count=22
$ cat fwconcat0.bin fwconcat1.bin > firmware.bin

Transfer firmware.bin and loader.bin to the OpenWrt device. First, flash
loader.bin to mtd device loader, then force sysupgrade:

$ mtd write loader.bin loader
$ sysupgrade -F firmware.bin

The reason for the two-step process is the way the flash layout is designed
for OpenWrt in contrast to the OEM firmware partition.

Signed-off-by: Andreas Böhler <dev@aboehler.at>
Link: https://github.com/openwrt/openwrt/pull/17089
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mediatek: MERCUSYS MR90X v1: add OpenWrt U-Boot (UBI) layout

This commit adds OpenWrt U-Boot (UBI) layout support for MERCUSYS MR90X
v1.

Stock U-Boot UBI size:   50 MiB
OpenWrt U-boot UBI size: 126 MiB

Install
-------
1. Perform steps 1-14 of the OpenWrt installation guide (use OpenWrt
   initramfs-recovery.itb instead of initramfs-kernel.bin at the step 10,
   12 and 14).
Link: https://openwrt.org/toh/mercusys/mr90x_v1#installation
2. Make backups:
```
cat /dev/mtd0 > /tmp/boot.bin
cat /dev/mtd5 > /tmp/tp_data.bin
```
   Copy /tp_data dir content, /tmp/boot.bin and /tmp/tp_data.bin and to
   your PC using scp. You can also backup the remaining partititons. Copy
   backups to a safe place, they are required for the next steps and stock
   firmware recovery.

3. Reboot to OpenWrt initramfs:
```
reboot
```

4. Copy OpenWrt ubi-bl31-uboot.fip, ubi-preloader.bin,
   ubi-squashfs-sysupgrade.itb and MT7986_EEPROM.bin, default-mac (from
   /tp_data backup) to the /tmp folder of the router using scp.

5. Prepare UBI:
```
ubidetach -p /dev/mtd3; ubiformat /dev/mtd3 -y; ubiattach -p /dev/mtd3
ubimkvol /dev/ubi0 -N fip -t static -s 1MiB
ubiupdatevol /dev/ubi0_0 /tmp/ubi-bl31-uboot.fip
ubimkvol /dev/ubi0 -N ubootenv -s 0x1f000
ubimkvol /dev/ubi0 -N ubootenv2 -s 0x1f000
```

6.  Install kmod-mtd-rw and unlock partitions:
```
opkg update && opkg install kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
mtd unlock boot
mtd unlock bl2
mtd unlock factory
```

7. Prepare "factory" partition:
```
dd if=/dev/zero bs=$((0x8000)) count=1 | tr '\000' '\377' > /tmp/factory.bin
dd if=/tmp/MT7986_EEPROM.bin of=/tmp/factory.bin conv=notrunc
dd if=/tmp/default-mac >> /tmp/factory.bin
```

8. Write "factory" partition:
```
mtd erase factory
mtd write /tmp/factory.bin factory
```

9. Write preloader partition:
```
mtd erase bl2
mtd write /tmp/ubi-preloader.bin bl2
```

10. Write OpenWrt sysupgrade image:
```
sysupgrade -n /tmp/ubi-squashfs-sysupgrade.itb
```

Recovery
--------
1. Place OpenWrt initramfs-recovery.itb image (with original name) on the
   tftp server (IP: 192.168.1.254).
2. Press "reset" button and power on the router. After ~10 sec release the
   button.
3. Use OpenWrt initramfs system for recovery.

BL2 and FIP recovery
--------------------
Use mtk_uartboot and UART connetion if BL2 or FIP in UBI is destroyed:
Link: https://github.com/981213/mtk_uartboot
Link: https://openwrt.org/toh/mercusys/mr90x_v1#serial
Return to stock:
----------------
1. Copy "boot" partition backup (boot.bin) to the /tmp dir of the router
   using scp.

2. Install kmod-mtd-rw:
```
opkg update && opkg install kmod-mtd-rw
```

3. Restore stock U-Boot:
```
   insmod mtd-rw i_want_a_brick=1
   mtd unlock boot
   mtd erase boot
   mtd write /tmp/boot.bin boot
```

4. Erase UBI and reboot:
```
mtd erase ubi
reboot
```

5. Open U-Boot web recovery, upload stock firmware image and start
   upgrade.
Link: http://192.168.1.1
6. Complete steps 1-9 of the OpenWrt installation guide to get root
   rights.
Link: https://openwrt.org/toh/mercusys/mr90x_v1#installation
7. Upload "tp_data" partition backup (tp_data.bin) to the /tmp folder of
   the router using scp.

8. Restore stock calibrations:
```
mtd write /tmp/tp_data.bin tp_data
reboot
```

9. Perform "factory restore" via stock firmware web interface.

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16744
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

uboot-mediatek: add MERCUSYS MR90X v1 support

Add U-Boot replacement loader for the MERCUSYS MR90X. This is required
to increase available flash space in OpenWrt.

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16744
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

arm-trusted-firmware-mediatek: add mt7986-spim-nand-ddr3 build

This commit adds mt7986-spim-nand-ddr3 build required for MERCUSYS MR90X
v1.

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16744
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ath79: Unify Sophos AP15/AP15C dts files

The recently added AP15C dts file only differs by the definition of the
reset button. Unify the shared definition into a dtsi to reduce code
duplication.

Signed-off-by: Christoph Krapp <achterin@gmail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://github.com/openwrt/openwrt/pull/16998
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mac80211: realtek: add RTL8812au/RTL8821au support

This adds support for RTL8812au/RTL8821au USB adapters.
Run-tested: x86/64/rockchip
USB adapters tested: Alfa AWUS036ACS, D-Link DWA-171 A1.

Signed-off-by: Marty Jones <mj8263788@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17079
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mac80211: realtek: backport support for RTL8812AU/RTL8821AU

Backport support for RTL8812AU/RTL8821AU USB adapters
Manually backported patch:
045-v6.13-wifi-rtw88-Enable-the-new-RTL8821AU-RTL8812AU-driver
Patches from 046 to 051 are pending.

Signed-off-by: Marty Jones <mj8263788@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17079
[Move BPAUTO_WANT_DEV_COREDUMP to original patch]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

linux-firmware: realtek: add RTL8812AU/RTL8821AU firmware

This adds firmware support for the RTL8812AU/RTL8821AU USB wireless adapters.

Signed-off-by: Marty Jones <mj8263788@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17079
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

linux-firmware: update to 20241110

linux-firmware update to 20241110
Move WCN6750 firmware to the device-specific subdir

git log --no-merges --pretty=oneline --abbrev-commit 20241110...20241017

1dbc4cfa rtl_bt: Update RTL8852BT/RTL8852BE-VT BT USB FW to 0x04D7_63F7
8a976e23 cnm: update chips&media wave521c firmware.
3636204f mediatek MT7920: update bluetooth firmware to 20241104091246
6627b025 linux-firmware: update firmware for MT7920 WiFi device
554c4761 copy-firmware.sh: Run check_whence.py only if in a git repo
1486d9aa cirrus: cs35l56: Add firmware for Cirrus CS35L56 for various Dell laptops
c99eeb4d amdgpu: update DMCUB to v9.0.10.0 for DCN351
b6bfff1a rtw89: 8852a: update fw to v0.13.36.2
ddf25515 rtw88: Add firmware v52.14.0 for RTL8812AU
dbb219d7 i915: Update Xe2LPD DMC to v2.23
937e463b linux-firmware: update firmware for mediatek bluetooth chip (MT7925)
62ee1c4b linux-firmware: update firmware for MT7925 WiFi device
a142ad72 WHENCE: Add sof-tolg for mt8195
fe16af92  linux-firmware: Update firmware file for Intel BlazarI core
c69bd749 qcom: Add link for QCS6490 GPU firmware
f4f5689f qcom: update gpu firmwares for qcs615 chipset
a6f3ab98 cirrus: cs35l56: Update firmware for Cirrus Amps for some HP laptops
048795ee ath11k: move WCN6750 firmware to the device-specific subdir
8a7bde2c xe: Update LNL GSC to v104.0.0.1263
e0ee2f91 i915: Update MTL/ARL GSC to v102.1.15.1926
987607d6 amdgpu: DMCUB updates for various AMDGPU ASICs
f9a502ab mediatek: Add sof-tolg for mt8195
1c289f28 i915: Add Xe3LPD DMC
c2379c61 cnm: update chips&media wave521c firmware.
71f8f3e0 linux-firmware: Add firmware for Cirrus CS35L41
65c4b9b7 linux-firmware: Update firmware file for Intel BlazarU core
4f397306 Makefile: error out of 'install' if COPYOPTS is set
2f046411 check_whence.py: skip some validation if git ls-files fails
feb324e3 qcom: Add Audio firmware for X1E80100 CRD/QCPs
3d45353e amdgpu: DMCUB updates forvarious AMDGPU ASICs
c569ca45 brcm: replace NVRAM for Jetson TX1

Signed-off-by: Marty Jones <mj8263788@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17079
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

Revert "ath79: elecom,wab: use nvmem"

This reverts commit 70e41d0205d95386881fa1cdf6ee00f6cca1b3f6.

"ethaddr" is stored into the "u-boot-env" (stock: "Config") partition
and it's quoted with double-quotations, but that format is not supported
by the current NVMEM u-boot-env driver (and mac_pton() function) and the
MAC address won't be parsed to byte array.
This causes random MAC addresses on the adapters, so revert the above
commit.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17116
Signed-off-by: Robert Marko <robimarko@gmail.com>

apk: build static

libapk as a library is used nowhere else and makes no sense to link it
shared. By linking static, we can take advantage of LTO and get the size
reduced further.

Some numbers locally:

Before:

168K staging_dir/target-mips_24kc_musl/root-ath79/usr/bin/apk*
252K staging_dir/target-mips_24kc_musl/root-ath79/usr/lib/libapk.so.2.99.0*

Static:
344K staging_dir/target-mips_24kc_musl/root-ath79/usr/bin/apk*

Static + LTO:
305K staging_dir/target-mips_24kc_musl/root-ath79/usr/bin/apk*

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17109
Signed-off-by: Robert Marko <robimarko@gmail.com>

image: apk: dont fail on removing a package that doesnt exist

Currently, in case when a package in the device package list is marked with
the "-"" prefix meaning that its supposed to be removed for that device but
it was not actually previously built it will cause the APK to error out it
and thus image generation will also fail.

So, lets do what OPKG build step does and supress the error with the "-"
prefix in make.

Fixes: #17103
Fixes: d788ab376f85 ("build: add APK package build capabilities")
Link: https://github.com/openwrt/openwrt/pull/17106
Signed-off-by: Robert Marko <robimarko@gmail.com>

mediatek/filogic: add Keenetic KN-3911 support

Specification:
 - MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
 - 512MB RAM
 - 128MB SPI NAND
 - 2 LEDs (green, orange)
 - 3 buttons (fn, reset, wps)
 - 2 2.5Gbit ethernet ports based on Airoha EN8811H phy

Serial Interface:
 - 3 Pins GND, RX, TX
 - Settings: 115200, 8N1

Notes:
 - The device supports dual boot mode

Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-mediatek-filogic-keenetic_kn-3911-squashfs-factory.bin"
   to "KN-3911_recovery.bin" and place it in tftp server directory.
3. Connect PC with ethernet port, press the reset button, power up
   the device and keep button pressed until status led start blinking.
4. Device will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16830
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mediatek/filogic: enable mtd virtual concat support

This is required for upcoming Keenetic KN-3911 support

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16830
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ramips: move zyimage creation to include/image-commands.mk

This is required for upcoming Keenetic KN-3911 support

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16830
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mediatek: filogic: Cudy WR3000S v1: fix CRLF line endings

DTS file for this device seems to be using CRLF line endings, so lets
convert them into Unix-style LF.

Fixes: faf4b3e0f7a5 ("mediatek: filogic: add support for Cudy WR3000S v1")
Link: https://github.com/openwrt/openwrt/pull/17096
Signed-off-by: Petr Štetiar <ynezz@true.cz>

mediatek: filogic: add KTD2026/7 driver to Acer Connect Vero W6m

This commit adds kmod-leds-ktd202x to the OpenWrt image for the device
"Acer Connect Vero W6m" which is equipped with one KTD2026 controlling the
device's status LED via I2C.

Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16860
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

generic: backport support for KTD2026/7 rgb(w) led controller

This commit adds the Linux kernel mainline driver "leds-ktd202x" for the
KinetIC KTD2026 and KTD2027 RGB/RBGW controller with I2C interface that was
introduced in kernel version 6.7, last changed in mainline on 2024-05-31.

At least the Acer Connect Vero W6m (a variant of the Acer Predator Connect
W6 without 2.5G eth1 port, usb3 port, and the 6 on-board gpio RGB LEDs) is
equipped with a KTD2026 (and a single RGB LED attached to it used by the
stock firmware as status LED), and maybe other router devices also are.

Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16860
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

config: build: remove experimental warning from USE_APK option

apk package manager is default for some time, so lets remove the
EXPERIMENTAL warning from the related option.

Signed-off-by: Petr Štetiar <ynezz@true.cz>

tools: ccache update to 4.10.2

Fixes since 4.10:

 * Fixed detection of Fmt version 11 and newer.
 * Fixed prefix command lookup from PATH.

Suggested-by: Jen Wolf <jenwolf@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/17105
Signed-off-by: Petr Štetiar <ynezz@true.cz>

meson: honor MESON_ARGS and MESON_HOST_ARGS when calling ninja

Set MESON_ARGS and MESON_HOST_ARGS when calling ninja for building.
This is required eg. to be able to set PYTHONPATH= not just for the
Meson (==configure) run but also for the build phase itself.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

gmp: use same source tarball for tools/gmp and package/libs/gmp

tools/gmp was using the .tar.xz while package/libs/gmp was using the
.tar.gz archive of the GMP release. Use the .tar.gz for both of them.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

base-files: fix manger->manager typo

It was reported, that a small typo sneaked in, so lets fix it.

Reported-by: @dave14305
Fixes: c19c31f7aa6f ("base-files: add migration information for APK")
Signed-off-by: Petr Štetiar <ynezz@true.cz>

netifd: update to Git 768027c5a7640137857f412f554227abd6160cdd (2024-11-27)

86da5cbcdb9d system-linux: do not pull ifindex/flags from netlink messages on rtnl events
cd96f61ba63e proto-shell: fix spurious interface teardowns with host deps
a39fe3a8b150 wireless: add support for adding a list of devices for a wifi-iface
d29cf707478c iprule: add ipproto property
768027c5a764 system-linux: restore reading flags from netlink messages

Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17074
Signed-off-by: Petr Štetiar <ynezz@true.cz>

uci: update to Git HEAD (2024-11-26)

10f7996ec294 file: Ignore config file with '.' in name

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>

base-files: add migration information for APK

If the `apk` package manager is installed, show a table of common
commands to deal with the system.

Signed-off-by: Paul Spooren <mail@aparcar.org>

build: profiles.json: add kernel version information

Currently downstream tools like ASU lack information about kernel
version to find out the relevant kmod build folder on downloads server.

So lets fix it by providing a new `linux_kernel` JSON array which would
for the start provide Linux kernel version, revision and vermagic
information.

  "linux_kernel": {
     "release": "1",
     "vermagic": "b57450c07d3a786158c3601fc5cee57d",
     "version": "6.6.61"
   },

Fixes: openwrt/openwrt#17036
Fixes: efahl/owut#9
Co-developed-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17042
Signed-off-by: Petr Štetiar <ynezz@true.cz>

mediatek: remove ktd-202x driver filogic image (Aer Vero W6m)

Image build fails with PR #16861 merged while PR #16860 not merged.

Removing kmod-leds-ktd202x from filogic.mk will fix the build process.

Fixes: 2898d1d1269a ("mediatek: add support for Acer Predator W6d and Acer Vero W6m")
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/17087
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

Revert "target,base-files: unify handling of procd-ujail"

This reverts commit ac640718aa0ceae55969bb9e7e45d00bb7bc228a as it
removes base-files package when KERNEL_NAMESPACES is deselected, as
base-files depends on procd-ujail which needs KERNEL_NAMESPACES.

Fixes: #17075
Link: https://github.com/openwrt/openwrt/pull/17081
Link: https://github.com/openwrt/openwrt/pull/17081
Signed-off-by: Petr Štetiar <ynezz@true.cz>

ramips: mt7621: support openwrt,netdev-name for renaming interfaces

Edgerouter X currently has its eth1 port on the switch missing since there
is a naming conflict currently.

So, as the root cause is mixing kernel support for DSA interfaces having
predictable names set via "label" property vs others having it assigned
dynamically lets avoid the conflict by using our own custom property as
suggested upstream [1].

So, add support via "openwrt,netdev-name" property and use it on ERX.

Fixes: 2a25c6ace8d8 ("ramips: get rid of downstream network device label patch")
Fixes: #15643
Link: https://github.com/openwrt/openwrt/pull/17062
Signed-off-by: Robert Marko <robimarko@gmail.com>

openwrt-keyring: apk: use just snapshot key explicitly

Currently we're going to ship all the apk keys in the keyring, but the
preference is to ship and use single release/branch specific key so lets
use openwrt-snapshots.pem for apk explicitly as well.

Fixes: 2cea05002489 ("openwrt-keyring: add apk public key for signing of package indexes")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Link: https://github.com/openwrt/openwrt/pull/16852
Signed-off-by: Robert Marko <robimarko@gmail.com>

Revert "openwrt-keyring: fix missing 24.10 usign key by installing it"

This reverts commit 37784c48e93c663dafc99454c24bebf4e258556f as the
preference is to have single explicit key for each release/branch.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Link: https://github.com/openwrt/openwrt/pull/16852
Signed-off-by: Robert Marko <robimarko@gmail.com>

qualcommax: ipq60xx: remove source-only flag

Its been a while since we added ipq60xx as source-only, it is now
quite usable so lets remove the source-only flag to start building
official images.

I also plan to merge additional popular boards rather soon.

Link: https://github.com/openwrt/openwrt/pull/17065
Signed-off-by: Robert Marko <robimarko@gmail.com>

kernel: enable pressure interface

PSI provides a canonical way to see resource pressure increases as
they develop, with pressure metrics for three major resources:
memory, CPU, and IO. PSI stats are like barometers that provide
fair warning of impending resource shortages, enabling users to
take more proactive, granular, and nuanced steps when resources
start becoming scarce.

References:
* https://www.kernel.org/doc/html/latest/accounting/psi.html
* https://lwn.net/Articles/759781/

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/glinet_gl-mt6000
Run-tested: x86/64/AMD Cezanne, flogic/glinet_gl-mt6000

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/13819
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mediatek: Routerich AX3000: add OpenWrt U-Boot layout

This commit adds OpenWrt U-Boot layout support for Routerich AX3000. The
aims:
1. Get open-source U-Boot;
2. Get maximum available free space in OpenWrt.

Install
-------
1. Copy OpenWrt ubootmod-bl31-uboot.fip, ubootmod-preloader.bin, to the
   /tmp folder of the router using scp.

2. Make mtd partitions backups:
   http://192.168.1.1/cgi-bin/luci/admin/system/flash -> Save mtdblock
   contents

3. Install kmod-mtd-rw:
```
opkg update && opkg install kmod-mtd-rw
```

4. Write FIP and preloader:
```
insmod mtd-rw i_want_a_brick=1
mtd unlock BL2
mtd erase BL2
mtd write /tmp/ubootmod-preloader.bin BL2
mtd unlock FIP
mtd erase FIP
mtd write /tmp/ubootmod-bl31-uboot.fip FIP
```

5. Copy OpenWrt ubootmod-initramfs-recovery.itb to the tftp server root
   with IP 192.168.1.254.

6. Reboot router:
```
reboot
```
U-Boot will automatically download from the tftp server and boot OpenWrt
initramfs system.

7. Copy OpenWrt ubootmod-squashfs-sysupgrade.itb to the /tmp dir of the
   router using scp.

8. Run sysupgrade:
```
sysupgrade -n /tmp/squashfs-sysupgrade.itb
```

Recovery
--------
1. Place OpenWrt initramfs-recovery.itb image (with original name) on the
   tftp server (IP: 192.168.1.254).
2. Press "reset" button and power on the router. After ~10 sec release the
   button.
3. Use OpenWrt initramfs system for recovery.

BL2 and FIP recovery
--------------------
Use mtk_uartboot and UART connection if BL2 or FIP in UBI is destroyed:
Link: https://github.com/981213/mtk_uartboot
Return to stock:
----------------
1. Copy partition backups (BL2.bin and FIP.bin) to the /tmp dir of the
   router using scp.

2. Install kmod-mtd-rw:
```
opkg update && opkg install kmod-mtd-rw
```

3. Restore stock U-Boot and reboot:
```
insmod mtd-rw i_want_a_brick=1
mtd unlock BL2
mtd erase BL2
mtd write /tmp/BL2.bin BL2
mtd unlock FIP
mtd erase FIP
mtd write /tmp/FIP.bin FIP
reboot
```

4. Open U-Boot web recovery, upload stock firmware image and start
   upgrade.
Link: http://192.168.1.1
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16791
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

uboot-mediatek: add Routerich AX3000 support

Add U-Boot replacement loader for Routerich AX3000.

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16791
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ramips: dna_valokuitu-plus-ex400: clean-up image creation

Code cleanup. Simplify and unify how kernel image is passed to
Build/dna-bootfs

Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/16811
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ramips: mt76x8: disable unused Ralink systick driver

The mt76x8 series SoCs use the MIPS generic systick timer. Sync the
upstream Ralink systick driver changes and disable it for mt76x8
target to reduce the kernel size.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16844
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: usb: kmod-usb-audio: Fix dependency

Change the dependency on the kmod-media-controller from depends to
select.

Fixes: 109592524663 ("kernel: add kmod-media-controller dependency for kmod-usb-audio")
Link: https://github.com/openwrt/openwrt/pull/17058
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

stm32: Remove unnecessary kernel options

These options are filtered out since some weeks, remove them also from
the new stm32 target.

Fixes: 851e7f77e424 ("stm32: add new stm32 target")
Link: https://github.com/openwrt/openwrt/pull/17058
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

CI: labeler: Add stm32 target

Add a label for changes in the stm32 target.

Fixes: 851e7f77e424 ("stm32: add new stm32 target")
Link: https://github.com/openwrt/openwrt/pull/17058
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

dropbear: bump to 2024.86

- update dropbear to latest stable 2024.86;
  for the changes see https://matt.ucc.asn.au/dropbear/CHANGES

Link: https://github.com/openwrt/openwrt/pull/17053
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

x86: Deactivate kernel options with extra overhead

Deactivate CONFIG_CONTEXT_TRACKING_USER_FORCE: Force user context
tracking: This is a testing feature which should not be activate in
production environments according to the Kconfig help. It adds an extra
overhead.

Deactivate CONFIG_RCU_NOCB_CPU_DEFAULT_ALL: Offload RCU callback
processing from all CPUs by default: This option should only be used in
aggressive HPC or real-time workloads which we do not have in OpenWrt.
For normal workloads it increases the number of context switches.

In the default Arch Linux kernel both options are not activated.

Fixes: 31111680f6fc ("x86: switch config to a tickless kernel")
Link: https://github.com/openwrt/openwrt/pull/17057
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

config: dont select procd-seccomp via USE_SECCOMP

base-files is including procd-secccomp as a dependency when USE_SECCOMP
is selected, so there is no point in selecting the package directly here
as well.

Link: https://github.com/openwrt/openwrt/pull/17048
Signed-off-by: Robert Marko <robimarko@gmail.com>

config: rename SECCOMP to USE_SECCOMP

It seems that we have some kind of a symbol name conflict which causes
CONFIG_SECCOMP to always be read as y.

Unfortunatelly, I could not figure out what is causing this, but simply
renaming SECCOMP to USE_SECCOMP seems to properly work and leaves the
symbol unset unless arch dependencies are satisfied.

This fixes qoriq and others that dont support seccomp from failing due
to procd-seccomp package being selected to get included but it cannot be
built for them:
ERROR: unable to select packages:
  procd-seccomp (no such package):
    required by: base-files-1637~52b6c92479[procd-seccomp]

Fixes: 4c65359af49b ("build: fix including busybox, procd and apk/opkg in imagebuilder")
Link: https://github.com/openwrt/openwrt/pull/17048
Signed-off-by: Robert Marko <robimarko@gmail.com>

mediatek: filogic: add support for Cudy WR3000S v1

Hardware
--------
MediaTek MT7981 WiSoC
256MB DDR3 RAM
128MB SPI-NAND (XMC XM25QH128C)
MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
UART: 115200 8N1 3.3V

MAC:
LAN MAC: label mac
WAN MAC: label mac + 1
2.4G MAC: label mac
5G MAC: label mac + 1 with LA bit set

Installation
------------

1. Connect to the serial port as described in the "Hardware" section.

2. Power on the device + press reset pin. Keep pressing reset pin to enter the U-Boot  shell.

3. Download the OpenWrt initramfs image. Place it on an TFTP server
   connected to the Cudy LAN ports. Make sure the server is reachable at
   192.168.1.88. Rename the image to "cudy3000s.bin"

4. Download and boot the OpenWrt initramfs image.

   $ tftpboot 0x46000000 cudy3000s.bin; bootm 0x46000000

5. Transfer the OpenWrt sysupgrade image to the device using scp.
   Install with sysupgrade.

Signed-off-by: David Ignjic <ignjic@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16939
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mediatek: fix Cudy AP3000 Outdoor label-mac

The label-mac does not match the one assigned to the ethernet interface.
Use the mac-address assigned to the wifi interface instead, as it
matches the one found on the device label.

Signed-off-by: David Bauer <mail@david-bauer.net>

mediatek: add support for Acer Predator W6d and Acer Vero W6m

This commit adds support for two variants of the already supported router
Acer Predator Connect W6: The Acer Predator Connect W6d (W6 without 6 GHz
wifi) and the Acer Connect Vero W6m (W6 without 2.5G eth1 port, usb3 port,
and the 6 on-board gpio RGB LEDs, and with a KTD2026 RGB LED controller
instead of the KTD2061 LED controller of the W6/W6d).

The device tree for the W6m refers to the KTD202x driver suggested in
PR #16860.

Patching target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
removes the code repetition in (old) lines 121 to 124 on the occasion.

This is the last of four commits into which the original commit was split
to make reviews easier and more targeted.

Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mediatek: improve device tree for Acer Predator Connect W6

In order to prepare for OpenWrt support other Acer W6 devices and to get
a step further to full hardware support for Acer Predator Connect W6, this
commit
- adjusts the product name ("Acer Predator Connect W6")
- updates gpio LED labels to function/color scheme
- show router status by using first rgb led instead of it's red color only
  (blue: booting/failsafe mode; red: sysupgrade; green: running – was: red)
- changes switch/eth1 led configuration to reflect RX/TX activity and speed
  (green: full 1Gbps/2.5Gbps speed; amber: lower speed; blink: RX/TX)
- shortens dummy dm-mod.create string in bootargs
- enables W6's i2c interface

This is the third of four commits into which the original commit was split
to make reviews easier and more targeted.

Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mediatek: make use of Acer Predator Connect W6's u-boot environment

In order to prepare OpenWrt support for other Acer W6 devices and to adapt
the procedure to read and set mac addresses which other devices of the same
target are using (instead of needing an additional script and creating an
additional structure in the file system), this commit
- reads device mac addresses from u-boot environment
- avoids the detour via the file system to set the mac addresses
- drops redundant file /lib/preinit/05_extract_factory_data.sh

The idea and the implementation were thankfully taken from PR #16410.

This is the second of four commits into which the original commit was split
to make reviews easier and more targeted.

Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mediatek: split Acer/W6 dts into W6 common dtsi and device specific dts

In order to prepare OpenWrt support for other Acer W6 devices, this commit
moves all device tree components that are used by all Acer W6/W6e/W6d/W6m
routers from mt7986a-acer-predator-w6.dts to mt7986a-acer-w6-common.dtsi
(new file) and includes this dtsi file in mt7986a-acer-predator-w6.dts.

Minor changes had to be made to the device tree in order to improve clarity
and – notably – to reduce the number of dtc warnings:
- replace (obviously wrong) led@<N> gpio led entities by led-<N>
- remove unnecessary (default-state = "off") gpio led statements
- rename entity “memory” to “memory@0”
- add missing #address-cells and #address-size in /soc/mmc@11230000
- add missing #address-cells and #address-size in /soc/pcie@11280000
- introduce symbols “nvmem” and “swport0” in dtsi (referenced in dts)

The changes were checked with `diff -BEZbdtwy --suppress-common-lines ...`
(comparing two dts files created using old and new fdt-1 blobs again), see
https://github.com/openwrt/openwrt/pull/16861/#issuecomment-2455680020 .

This is the first of four commits into which the original commit was split
to make reviews easier and more targeted.

Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

linux-firmware: Add support for Intel AX411

Add support for Intel AX411 CNVio2 device.

Signed-off-by: Joerg Bayer <sg-o@live.de>
Link: https://github.com/openwrt/openwrt/pull/15153
[squashed and updated commit description, update to version 89]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ath79: add support for TP-Link CPE710-v2

TP-Link CPE710-v2 is an outdoor wireless CPE for 5 GHz with one Ethernet
port based on the AP152 reference board. Compared to the CPE710-v1, the
only change observed in hardware is that the mdio address of the ethernet
physical changed from 0x4 to 0x0.

Specifications:
- SoC: QCA9563-AL3A MIPS 74kc @ 775MHz, AHB @ 258MHz
- RAM: 128MiB DDR2 @ 650MHz
- Flash: 16MiB SPI NOR Based on the GD25Q128
- Wi-Fi 5Ghz: ath10k chip (802.11ac for up to 867Mbps on 5GHz wireless
  data rate), based on the QCA9896
- Ethernet: one 1GbE port
- 23dBi high-gain directional 2×2 MIMO parabolic antenna
- Power, LAN, WLAN5G Blue LEDs

Flashing instructions:
Flash factory image through stock firmware WEB UI or through TFTP
To get to TFTP recovery just hold reset button while powering on for around
30-40 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254

Signed-off-by: Tim Noack <tim@noack.id>
Link: https://github.com/openwrt/openwrt/pull/16637
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ath79: refactor dts of TP-Link CPE710-v1

This is done in preparation of adding support for the CPE710-v2,
which uses a similiar device tree.

Signed-off-by: Tim Noack <tim@noack.id>
Link: https://github.com/openwrt/openwrt/pull/16637
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ramips: mt76x8: Add support for Zbtlink ZBT-WE2426-B

The Zbtlink ZBT-WE2426-B is an indoor dual band WiFi router
with 4 external non detachable antennas and 5 Fast Ethernet ports.

Hardware of ZBT-WE2426-B:
- SoC: MT7628AN
- RAM: 64 MB (Winbond W9751G6K8-25)
- Storage: 8 MB SPI flash (S25FL064K)
- Ethernet: 5x 10/100 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
- Wireless: 2.4GHz: on SoC (802.11b/g/n)
- Wireless: 5GHz: Mediatek MT7612EN (802.11n/ac)
- LEDs: 8x
- Buttons: 1x reset
- USB: 1x 2.0
- MicroSD slot: 1x
- Power: 9 VDC, 1 A
- Uart: GND TX RX PWR - J1 on the PCB
- Board silkscreen: "ZBT-WE2426-C V04" "2018-02-28" "CTT" "13 18"

Backup the stock firmware, settings and calibration data:
This router comes with PandoraBox OpenWrt firmware, so it is
possible to get all MTD partitions using scp.

Installation:
- Using the bootloader web server. Hold the reset button while turning
  the power on. Upload the sysupgrade image on http://192.168.1.1.
- Using the sysupgrade command in PandoraBox OpenWrt.

LEDs:
- LAN1,LAN2,LAN3,LAN4,WAN,WLAN2G use GPIO pins of the MT7628AN SoC
  (GPIOs 43,42,41,40,39,44)
- WLAN5G uses pin of MT7612EN.
- The POWER LED is directly connected to the VCC. It can be reconnected to
  the GPIO 37 of the MT7628AN SoC by resoldering SMD resistor on the PCB.

Buttons:
- The RESET button is connected to the GPIO 38 of the MT7628AN SoC.

MAC addresses as verified by OEM firmware:
use   address   source
2g    *:b0      factory 0x4 (label)
5g    *:b1      factory 0x8004
LAN   *:b2      factory 0x28
WAN   *:b3      factory 0x2e

Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
Link: https://github.com/openwrt/openwrt/pull/16927
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mvebu: devm for mutex_init

It's common to avoid calling mutex_destroy when done. It's not correct
strictly speaking.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16753
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mxs: run kernel_oldconfig

small change.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16913
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: modules: appletalk: add for Netatalk v4

Netatalk v4 reintroduces AppleTalk and this module is required for
layer 3 protocol support.

Module was removed in kernel 4.14 for OpenWrt 18.06 (commmit
14a0131, 22/02/2018). At the time nothing used it as Netatalk v3
did not support AppleTalk.

Not building ipddp feature/module like it was in the past, as
recommended by upstream Netatalk maintainers.

Signed-off-by: Antonio Pastor <antonio.pastor@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16979
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

stm32: add new stm32 target

New stm32 target introduces support for stm32mp1 based devices.
For now it includes an initial support of the STM32MP135F-DK device.
The specifications bellow only list supported features.

Specifications
--------------

SOC: STM32MP135FAF7
RAM: 512 MiB
Storage: SD Card
Ethernet: 2x 100 Mbps
Wireless: 2.4GHz Cypress CYW43455 (802.11b/g/n)
LEDs: Heartbeat (Blue)
Buttons: 1x Reset, 1x User (USER2)
USB: 4x 2.0 Type-A

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: package v4l2-async and v4l2-fwnode drivers

These packages are needed for the stm32/stm32mp1 subtarget.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: add kmod-media-controller dependency for kmod-usb-audio

The snd-usb-audio drivers uses media controller if media controller is set.
So add kmod-media-controller as dependency.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: package media controller driver

It is needed for the stm32/stm32mp1 subtarget.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: package industrialio-buffer-cb driver

It is needed for the stm32/stm32mp1 subtarget.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: package crypto_engine driver

It is needed for the stm32/stm32mp1 subtarget.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: unset CONFIG_DEVFREQ_THERMAL in kmod-thermal package

It is needed for the stm32/stm32mp1 subtarget.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: package snd-soc-dmic driver

It is needed for the stm32/stm32mp1 subtarget.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: package industrialio-hw-consumer driver

It is needed for the stm32/stm32mp1 subtarget.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

murata-nvram: add new package

This package contains nvram files for Murata's Wi-Fi/Bluetooth modules.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

murata-firmware: add new package

This package contains firmwares provided by Murata.
See https://community.murata.com/.

Murata firmwares are used by wifi chip on stm32 boards.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mac80211: enable CONFIG_BRCMFMAC_SDIO for stm32

All stm32 devices use BCM43430 Wi-Fi interface in SDIO mode.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

arm-trusted-firmware-stm32: add ATF for stm32 boards

Add ATF for stm32 boards, with the first being STM32MP135F-DK.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

uboot-stm32: add U-Boot for stm32 boards

Add U-Boot for stm32 boards, with the first being STM32MP135F-DK.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

optee-os-stm32: add OP-TEE for stm32 boards

Add OP-TEE for stm32 boards, with the first being STM32MP135F-DK.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

build: add generic build template for optee-os packages

Add a generic template include/optee-os.mk to build OP-TEE.

Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mediatek: change Routerich AX3000 ubi size
All new routers are shipped with ubi size 112MB since early September.
Bootloader update required (ask vendor , see wiki)

These partitions weren't used:
firmware_backup
zrsave
config2

Signed-off-by: Romanov Danila <pervokur@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16686
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

x86: add all ports to the Gowin 1U default network config

Commit e52c57bb1b30375e0bcc5523db76a672a4a8b4a4 renamed all
network ports to match the faceplate of the Gowin 1U Rack
Mount Server and added the br-lan bridge for the eth* ports.

This commit adds the PoE port to the br-lan bridge and a
br-wan bridge for the two SFP ports so that all ports are
part of the default network configuration.

Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/16965
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ramips: sync upstream Ralink clock patches

1. Add sdhc clock for MT7620 and MT76x8 SoCs.
2. Fix clock driver warning for RT2880, RT305x and RT3883.

Link: https://lore.kernel.org/all/20240910044024.120009-1-sergio.paracuellos@gmail.com/
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17037
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: bump 6.6 to 6.6.63

Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.63

Manually rebased:
bcm27xx/patches-6.6/950-0297-staging-vchiq_arm-Add-36-bit-address-support.patch

All other patches automatically rebased.

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16997
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: bump 6.6 to 6.6.62

Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.62

All patches automatically rebased.

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/glinet_gl-mt6000, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, flogic/glinet_gl-mt6000, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16997
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

wifi-scripts: Fix parsing of Capabilities

Fixup capabilities parsing in iw output.

In addition to the normal capabilities iw now also outputs HE MAC, HE
PHY and EHT MAC and EHT PHY capabilities. Exclude them in the parsing.

The grep returns this with mac80211-hwsim:
```
root@OpenWrt:~# iw phy phy0 info | grep 'Capabilities:'
Capabilities: 0x107e
HE PHY Capabilities: (0x02bfce0000000000000000):
EHT PHY Capabilities: (0x7c0000feffff7f01):
HE PHY Capabilities: (0x02bfce0000000000000000):
EHT PHY Capabilities: (0x7c0000feffff7f01):
HE PHY Capabilities: (0x02bf000000000000000000):
Capabilities: 0x107e
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfc1f3ffeffff7f37):
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfc1f3ffeffff7f37):
HE PHY Capabilities: (0x1cbf000000000000000000):
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfefffffeffffff7f):
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfefffffeffffff7f):
HE PHY Capabilities: (0x1cbf000000000000000000):
Capabilities: 0x107e
```

With busybox 1.36.1 the ht_cap_mask variable will be set to
-72057598332895361. With busybox 1.37.0 it will be set to -1.
Both values are wrong, after this change it will be set to 4222
(0x107E).

Link: https://github.com/openwrt/openwrt/pull/17043
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

Revert "mediatek: fix pwn fan settings for sinovoip bpi-r3"

This reverts commit 3467ea905b40f0df87700a15b716b1f5a4efc955.

I merged it by accident.

Signed-off-by: Robert Marko <robimarko@gmail.com>

mediatek: fix pwn fan settings for sinovoip bpi-r3

Popular bpi-r3 pwm fans like this one

  https://www.amazon.com/youyeetoo-Barebone-Fan-BPI-R3-Integrated/dp/B0CCCTY8PS

will not work properly with current openwrt-23.05/24.10 firmware.
Trying different pwm setting

  echo $value > /sys/devices/platform/pwm-fan/hwmon/hwmon1/pwm1

I found:

  pwm1 value     fan rotation speed   cpu temperature     notes
  -----------------------------------------------------------------
    0            maximal              31.5 Celsius        too noisy
   40            optimal              35.2 Celsius        no noise hearable
   95            minimal
   above 95      does not rotate      55.5 Celsius
  -----------------------------------------------------------------

At the moment we have following cooling levels:

  cooling-levels = <255 96 0>;

for cpu-active-high, cpu-active-medium and cpu-active-low modes correspondingly.
Thus only cpu-active-high and cpu-active-low are usable. I think this is wrong.

This patch fixes cpu-active-medium settings for bpi-r3 board.

PS: I know, the patch is not ideal as it can break pwm fan for some users.
    There are some peoples that use handmade cooling solutions, but:
      * discussed cooler is the only 'official' pwm cooler for bpi-r3
        available on the market.
      * most peoples will use passive cooling available on the market or
        the discussed cooler.
      * the pwm-fan dts section was added before the official cooler
        appears on the market.
    Thus it should not be a lot of harm from this fix.

Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16974
Signed-off-by: Robert Marko <robimarko@gmail.com>

build: fix filtering of non-upgradable packages

Add anchor to name search so that we don't inadvertently filter out
packages containing, say, "kernel-" as part of their name.

Fixes: openwrt/packages#25372
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17032
Signed-off-by: Robert Marko <robimarko@gmail.com>

include/package-pack: add support for postrm with APK

Currently, postrm scripts are not being executed when package is removed
with APK since they are not being included at all.

So, lets use APK-s support for post-deinstall scripts and ship our postrm
scripts if packages define them.

Fixes: d788ab376f85 ("build: add APK package build capabilities")
Link: https://github.com/openwrt/openwrt/pull/17023
Signed-off-by: Robert Marko <robimarko@gmail.com>

include/package-pack: actually call default_postinist/prerm when using APK

Currently, when you install a package that ships uci-defaults scripts they
are not getting executed during package installation.

For example, if you install a new LuCI theme it ships a uci-defaults script
to add it to the UCI LuCI config so the theme is actually selectable but
that does not happen until the device is rebooted so that uci-defaults
script is actually executed.

It turns out that the recipe for post-install is the issue since it will
include contents of postinst-pkg before the call to default_postinist.
This is an issue since postinst-pkg will exit with code 0 before we ever
reach the call to default_postinist.

So, lets simply make the call to default_postinist before postinst-pkg
inclusion which is what OPKG based installation does.

The same issue affects pre-deinstall script but its not actually being hit
since we dont seem to be actually even generating prerm-pkg scripts but
lets fix this theoretical issue as well.

Fixes: #16987
Fixes: d788ab376f85 ("build: add APK package build capabilities")
Link: https://github.com/openwrt/openwrt/pull/17023
Signed-off-by: Robert Marko <robimarko@gmail.com>

imagebuilder: fix OPKG package_whatdepends support

Trying to use 'package_whatdepends' feature of the ImageBuilder with OPKG
will currently fail as OPKG does not support "list --depends" call at all,
it seems that this is a mixup from the original APK support commit.

So, lets restore 'package_whatdepends' support for OPKG by calling
"whatdepends -A" instead as we used to before APK support.

Fixes: d788ab376f85 ("build: add APK package build capabilities")
Link: https://github.com/openwrt/openwrt/pull/17022
Signed-off-by: Robert Marko <robimarko@gmail.com>

imagebuilder: fix APK package_depends support

Currently trying to use the 'package_depends' feature of ImageBuilder will
result in it trying to call OPKG:
make package_depends PACKAGE="usbutils"
OK: 26 MiB in 142 packages
bash: line 1: openwrt-imagebuilder-qualcommax-ipq807x.Linux-x86_64/staging_dir/host/bin/opkg: No such file or directory
make: *** [Makefile:363: package_depends] Error 127

It looks like a copy/paste error when APK support was being added, so lets
fix it by calling APK and its "info --depends" command.

Fixes: #16996
Fixes: d788ab376f85 ("build: add APK package build capabilities")
Link: https://github.com/openwrt/openwrt/pull/17022
Signed-off-by: Robert Marko <robimarko@gmail.com>

mpc85xx: p2020: add missing symbols

Since kernel_oldconfig doesn't work properly with it, I ran that first
and then moved all the config symbols to config-6.6 and found the
differences.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16847
Signed-off-by: Robert Marko <robimarko@gmail.com>

mpc85xx: p1020: add missing symbols

Since kernel_oldconfig doesn't work properly with it, I ran that first
and then moved all the config symbols to config-6.6 and found the
differences.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16847
Signed-off-by: Robert Marko <robimarko@gmail.com>

mpc85xx: p1010: add missing symbols

Since kernel_oldconfig doesn't work properly with it, I ran that first
and then moved all the config symbols to config-6.6 and found the
differences.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16847
Signed-off-by: Robert Marko <robimarko@gmail.com>

mpc85xx: run make kernel_oldconfig

Adjusts the default config to modern kernels.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16847
Signed-off-by: Robert Marko <robimarko@gmail.com>

apk: update to git e3464d096708b270138653ef93db59134bb24813 (2024-11-13)

Allows us to drop the description backport.

Changes:
e3464d0 db: make repository description an atom instead of allocation
417a93c pkg: truncate apkv3 description to 256 bytes
d26b65d db, audit: remove support for files without embedded checksum
64ff8c7 db: allow files starting with a dot in the root directory of apk3 packages
89e4bf1 db, fs: do not extract devices in --usermode
4050f9e db: fix hardlink handling: root directory and v3 checksums
ade0be3 db, extract: handle file/directory extraction errors more consistently
a4837ae package: don't call make_device_tree when APK_NO_CHROOT is set
1e04115 package: respect libexecdir instead of hard-coding /usr/libexec
76970a9 package: move the location of executable package scripts
19b1df7 blob: refactor apk_blob_for_each_segment into apk_blob_foreach_word
e38d5b5 test: add missing alpine tests makefile
fcd4def test: move vertest to cmocka based unit testing infrastructure
8a13ed9 test: fix solver.sh for parallel use
5add6fc (tag: v3.0.0_pre4) apk-tools-3.0.0_pre4
5dd91e3 db: consider --force-no-chroot when determining /dev/fd availability
d86afde db: print message when a file is written to .apk-new
a5aeb3d test: unify makefile and meson tests
a236fdd pkg: use memfd_create only if target root has dev/fd working
563d364 tests: minor updates to root tests
08b4d21 tests: move solver test data to separate directory
c259642 tests: rework solver tests to not require apk-test binary
d2aaf13 commit: sort matched dependencies on error analysis
98d7196 db: fix permissions of arch file
b231eac db: simplify add_repos_from_file
2a3dbfc db: add and use apk_db_parse_file helper to parse files line by line
c1a3e69 db: validate package arch against compatible arches

Link: https://github.com/openwrt/openwrt/pull/17015
Signed-off-by: Robert Marko <robimarko@gmail.com>

imagebuilder: fix APK architecture setting

Currently, when "apk add --initdb" is called it will populate the
/etc/apk/arch file with the architecture of the host instead of the target
package architecture and this will then make it impossible for new packages
to be installed on the device as the target architecture will not match
after APK is updated to include [1].

So, lets use override the architecture by passing the target package one
by using the "--arch" argument to "apk add".

[1] https://gitlab.alpinelinux.org/alpine/apk-tools/-/commit/c1a3e69f24e235fc78f4dddb1f85fdf281464446

Fixes: #16953
Link: https://github.com/openwrt/openwrt/pull/17015
Signed-off-by: Robert Marko <robimarko@gmail.com>

include/package-pack: translate PKGARCH for APK

We have a lot of script-only packages that are universal for all arch-s
and those set PKGARCH:=all to indicate it.

Unfortunately, APK expects architecture to be set to "noarch" instead to
indicate that its universal so instead of having to update all packages
that set PKGARCH:=all and thus break OPKG lets simply translate "all" to
"noarch" when generating the APK package.

This will be required as soon we update APK to include [1] as it will start
enforcing package architecture checks.

[1] https://gitlab.alpinelinux.org/alpine/apk-tools/-/commit/c1a3e69f24e235fc78f4dddb1f85fdf281464446

Suggested-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17015
Signed-off-by: Robert Marko <robimarko@gmail.com>

ipq806x: tr4400v2: fix dtc warnings by deleting stock partitions

The original set of stock partitions was kept in the TR4400 v2 port,
with the same partition numbers but their names prefixed with 'stock_'.
This allowed scripts (installation, back to stock, etc) to run on both
stock and OpenWrt firmware. But this triggers warnings in the device
tree compiler, as partitions of the old and new schemes overlap.

This commit fixes the dtc warnings by deleting the stock partitions,
also renumbering some of the remaining MTD partitions in the process.
Additionally, the 'fw_env' partition is set to read-only.

These changes can break existing scripts as well as user configurations
that utilize the 'extra' partition. Users wanting to run old scripts can
do so by reverting to the 23.05 series releases.

Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16958
Signed-off-by: Robert Marko <robimarko@gmail.com>

include/package-pack: add default 'provider_priority' for APK packages

Currently, trying to use APK to install a package that has a dependency on
a virtual package that needs to be resolved via 'provides' it will fail if
package does not have 'DEFAULT_VARIANT:=1' like:
apk add usbutils
ERROR: unable to select packages:
  libudev (virtual):
    note: please select one of the 'provided by' packages explicitly
    provided by: libudev-zero
    required by: usbutils-017-r1[libudev]

Issue is that we dont set 'provider_priority' that APK uses to break ties
when choosing a virtual package to satisfy a dependency and thus despite
only one package providing the dependency it will still end up with a tie
and just error out.

So, lets simply fix this by providing a default value for
'provider_priority' when 'DEFAULT_VARIANT' is not set and then APK will
be able to resolve dependencies.

Fixes: #16976
Link: https://github.com/openwrt/openwrt/pull/17008
Signed-off-by: Robert Marko <robimarko@gmail.com>

odhcp6c: update to Git HEAD (2024-09-25)

b6ae9ffaeb0e odhcp6c: allow to request specific ipv6 prefix

Signed-off-by: He Ping <pinghejk@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17013
Signed-off-by: Petr Štetiar <ynezz@true.cz> [hash, commit]