ath9k: classify DFS debug header further

DFS_DEBUG_H is very generic, instead use something more specific
to ath9k such as ATH9K_DFS_DEBUG_H.

Reported-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-linville' of git://git./linux/kernel/git/luca/wl12xx

wl12xx: mark no sched scan only after FW event

stop sched scan isn't an immediate operation
and we need to wait for PERIODIC_SCAN_COMPLETE_EVENT_ID
after sending a stop before changing internal state
and notifying upper layers.
Not doing this caused problems when canceling an existing sched
scan and immediately requesting to start a new one
with a different configuration as the FW was still
in the middle of the previous sched scan.

Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: fix sched scan of DFS channels

DFS channels weren't scanned properly because
min/max_duration weren't set for these channels
even though they're required by the FW.
The change sets passive_duration and min/max_duration
for all channels as the FW uses the correct parameters
according to the channel type.

Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: add missing copyright notice

The wl12xx_platform_data.c file did not have a proper copyright
notice.

Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: check the actual vif operstate in wl1271_dev_notify

The current wl1271_dev_notify implementation sets the
new operstate to all associated stations (while only
a specific vif was changed).

Until we'll have a method to get the actual vif from
the given dev, check the current operstate of each vif.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: stop device role on remove_interface

When removing a sta/ibss role, the device role has to
stopped (and disabled) as well.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: fix checking of started dev role

dev_role_id only indicates whether the dev role
is enabled, not started (e.g. on IBSS merge,
the device role is enabled, but not started).

Checking for any role in ROC (in order to determine
whether dev role was started) is wrong as well,
especially in multi-vif env.

Check for started dev role only by checking the dev_hlid.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: flush packets before stopping dev role

During sta disconnection, a deauth packet is being queued to
the dev role queue. However, the dev role is being stopped
before the packet was sent.

Flush the tx queue before stopping the dev role.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: make WL1271_FLAG_IDLE flag per-vif

This flag should be set per-vif, rather than globally.

Rename the flag to indicate IN_USE (rather than IDLE), as
in the default configuration (i.e. flag is clear) the vif
should be idle.

Change all the bit operations (and elp conditions) appropriately.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: remove redundant code from wl1271_op_conf_tx

Since the conf_tx callback passes the vif as param,
we must have been added first (and mac80211 verifies it).

Remove the handling of such case.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

wl12xx: implement change_interface

Implement the change_interface callback by simply removing the
current vif and adding a new one after updating the vif type.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>

iwlwifi: Execute runtime calibration always

Runtime DC calibration was previously conditional. Remove this
behaviour, as new devices support runtime DC calibration,
while older devices ignore the runtime DC calibration request.

This patch addresses low TX throughput issues seen with the 6205.

Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: use bus_get_hw_id for IWL_TM_CMD_APP2DEV_GET_DEVICE_ID

instead of doing all the work in IWL_TM_CMD_APP2DEV_GET_DEVICE_ID, just use
the information from bus_get_hw_id()

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: set hw_version in wiphy

Set the hw_version in wiphy structure

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: deliver hw version in both string and u32 format

Add function to get hw version in both strind and u32 format

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: finer-grained HT disable

At least while debugging, a lot of people use
11n_disable=1 to disable HT completely. To be
able to figure out what parts of HT cause the
problems we see, make the parameter a bitmap,
allowing to disable all of HT and aggregation
(TX/RX) separately.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: add IRQ tracing

The legacy IRQs could be read from a trace by their
IO accesses, but reading the ICT doesn't leave any
trace (pun intended ;-) ) so in order to see what
input they get we need to add specific tracepoints.

While at it, fix whitespace in two related places.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

mac80211: Fixing sparse warning at sta_info.c

The commit 42624d4913a00219a8fdbb4bafd634d1d843be85
created following sparse warning
>net/mac80211/sta_info.c:965:24: warning: incorrect type in assignment (different address spaces)
>net/mac80211/sta_info.c:965:24:    expected struct tid_ampdu_tx *tid_tx
>net/mac80211/sta_info.c:965:24:    got struct tid_ampdu_tx [noderef] <asn:4>*<noident>

Making use of rcu_dereference_protected to fix the problem.

V2:
 - Replacing rcu_dereference with rcu_dereference_protected
   as suggested by Johannes.
 - Adding mutex_lock/unlock to satisfy the condition at
   rcu_dereference_protected

Cc: Nishant Sarmukadam <nishants@marvell.com>
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix tx locking issues

The commit "ath9k: simplify tx locking" introduced a soft lockup triggered
by mac80211 sending a BAR frame triggered by a driver call to
ieee80211_tx_send_bar or ieee80211_tx_status.
Fix these issues by queueing processed tx status skbs and submitting them
to mac80211 outside of the lock.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: make bluetooth coexistence support optional at compile time

Many systems (e.g. embedded systems) do not have wifi modules connected to
bluetooth modules, so bluetooth coexistence is irrelevant there. With the
addition of MCI support, ath9k picked up quite a bit of extra code that
can be compiled out this way.

This patch redefines ATH9K_HW_CAP_MCI and adds an inline wrapper for
querying the bluetooth coexistence scheme, allowing the compiler to
eliminate code that uses it, with only very little use of #ifdef.

On MIPS this reduces the total size for the modules by about 20k.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: reorder functions: random cleanups

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: reorder functions: move rest of workarounds

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: reorder functions: move RSSI calibration

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: split gain control workarounds

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: reorder functions: collect RSSI selects

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: reorder functions: collect samples ones

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: reorder functions: collect radio ones

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: reorder functions: put basic ones at beginning

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Fix locking problem introduces with commit 6539306b

When I tested commit 6539306, I did not notice that loading an out-of-tree
module turns off lockdep testing in kernel 3.2. For that reason, I missed
the kernel WARNING shown below:

The solution fixes the warning by partially reverting commit 6539306.

[   84.168146] ------------[ cut here ]------------
[   84.168155] WARNING: at kernel/mutex.c:198 mutex_lock_nested+0x309/0x310()
[   84.168158] Hardware name: HP Pavilion dv2700 Notebook PC
[   84.168161] Modules linked in: nfs lockd auth_rpcgss nfs_acl sunrpc af_packet cpufreq_conservative cpufreq_userspace cpufreq_powersave powernow_k8 mperf e
xt3 jbd ide_cd_mod cdrom snd_hda_codec_conexant arc4 rtl8192ce ide_pci_generic rtl8192c_common rtlwifi snd_hda_intel mac80211 snd_hda_codec snd_pcm snd_timer
 amd74xx ide_core cfg80211 k8temp snd joydev soundcore hwmon battery forcedeth i2c_nforce2 sg rfkill ac serio_raw snd_page_alloc button video i2c_core ipv6 a
utofs4 ext4 mbcache jbd2 crc16 sd_mod ahci ohci_hcd libahci libata scsi_mod ehci_hcd usbcore usb_common fan processor thermal
[   84.168231] Pid: 1218, comm: kworker/u:2 Not tainted 3.2.0-rc5-wl+ #155
[   84.168234] Call Trace:
[   84.168240]  [<ffffffff81048aaa>] warn_slowpath_common+0x7a/0xb0
[   84.168245]  [<ffffffff81048af5>] warn_slowpath_null+0x15/0x20
[   84.168249]  [<ffffffff813811f9>] mutex_lock_nested+0x309/0x310
[   84.168269]  [<ffffffffa00793f9>] ? rtl_ips_nic_on+0x49/0xb0 [rtlwifi]
[   84.168277]  [<ffffffffa00793f9>] rtl_ips_nic_on+0x49/0xb0 [rtlwifi]
[   84.168284]  [<ffffffffa007ab85>] rtl_pci_tx+0x1b5/0x560 [rtlwifi]
[   84.168291]  [<ffffffffa007635a>] rtl_op_tx+0x9a/0xa0 [rtlwifi]
[   84.168359]  [<ffffffffa043cf51>] __ieee80211_tx+0x181/0x2b0 [mac80211]
[   84.168375]  [<ffffffffa043ef06>] ieee80211_tx+0xf6/0x120 [mac80211]
[   84.168391]  [<ffffffffa043ee49>] ? ieee80211_tx+0x39/0x120 [mac80211]
[   84.168408]  [<ffffffffa043f80b>] ieee80211_xmit+0xdb/0x100 [mac80211]
[   84.168425]  [<ffffffffa043f730>] ? ieee80211_skb_resize.isra.26+0xb0/0xb0 [mac80211]
[   84.168441]  [<ffffffffa0440b2a>] ieee80211_tx_skb_tid+0x5a/0x70 [mac80211]
[   84.168458]  [<ffffffffa0443da2>] ieee80211_send_auth+0x152/0x1b0 [mac80211]
[   84.168474]  [<ffffffffa042e169>] ieee80211_work_work+0x1049/0x1860 [mac80211]
[   84.168489]  [<ffffffffa042d120>] ? free_work+0x20/0x20 [mac80211]
[   84.168504]  [<ffffffffa042d120>] ? free_work+0x20/0x20 [mac80211]
[   84.168510]  [<ffffffff81065ffc>] process_one_work+0x17c/0x530
[   84.168514]  [<ffffffff81065f92>] ? process_one_work+0x112/0x530
[   84.168519]  [<ffffffff81066994>] worker_thread+0x164/0x350
[   84.168524]  [<ffffffff8108420d>] ? trace_hardirqs_on+0xd/0x10
[   84.168528]  [<ffffffff81066830>] ? manage_workers.isra.28+0x220/0x220
[   84.168533]  [<ffffffff8106bc17>] kthread+0x87/0x90
[   84.168539]  [<ffffffff813854b4>] kernel_thread_helper+0x4/0x10
[   84.168543]  [<ffffffff81382bdd>] ? retint_restore_args+0xe/0xe
[   84.168547]  [<ffffffff8106bb90>] ? __init_kthread_worker+0x70/0x70
[   84.168552]  [<ffffffff813854b0>] ? gs_change+0xb/0xb
[   84.168554] ---[ end trace f25a4fdc768c028f ]---

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stanislaw Gruska <sgruszka@redhat.com>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: add Kconfig option for SDIO bus support

This patch adds a Kconfig option for SDIO bus support and abstracts
a build subset correspondingly. It's the final patch of fullmac bus
interface refactoring.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: exclude unnecessary header files

This patch removes some headers files include lines from sdio layer
code. This is part of the fullmac bus interface refactoring.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: move idle macros to dhd_sdio.c

The idle macros are only used by dhd_sdio.c. It's more appropriate
to place them in dhd_sdio.c instead of dhd.h.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: move debug level macros to dhd_dbg.h

Debug message level macros are used for debug purpose. It would be
more appropriate to place them at dhd_dbg.h.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: abstract ctrl frames interface function pointers

Abstract bus layer brcmf_bus_txctl/brcmf_bus_rxctl function
pointers for common layer. This patch is part of the fullmac bus
interface refactoring.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: abstract bus_txdata interface function pointer

Abstract bus layer brcmf_bus_txdata function pointer for common
layer. This patch is part of the fullmac bus interface refactoring.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: abstract bus_init interface function pointer

Abstract bus layer brcmf_bus_init function pointer for common
layer. This patch is part of the fullmac bus interface refactoring.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: move common layer bus interface context to dhd_bus.h

dhd_bus.h is the header file for bus interface. Move functions
declarations and brcmf_bus structure to there. This is part of
the fullmac bus interface refactoring.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: abstract bus_stop interface function pointer

Common layer should use interface function pointer stored in
brcmf_bus to invoke corresponding interface function in bus layer.
This patch is part of the fullmac bus interface refactoring.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: move sdio related macros to sdio_host.h

dhd_bus.h will be used as the shared header file for common layer
and bus layer. It should not contain any sdio specific macros.
This patch moves them to sdio_host.h as part of the fullmac bus
interface refactoring.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: stop referencing brcmf_sdio in common layer

brcmf_sdio is the data structure for sdio bus layer. Stop
referencing brcmf_sdio from common layer. This patch is part of
the fullmac bus interface refactoring.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: stop referencing brcmf_pub in bus layer

brcmf_pub is the data structure for common layer. Since brcmf_bus
should be the only structure shared by common layer and bus layer,
stop referencing brcmf_pub from bus layer. This patch is part of
the fullmac bus interface refactoring.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: move tx flow ctrl flag to bus layer

txoff is the flow control flag for transmit used in sdio layer.
Move it to bus layer data structure brcmf_sdio. Also flag
management code is moved out of brcmf_txflowcontrol(). This is
part of the fullmac bus interface refactoring.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: move packet realloc stats to struct brcmf_bus

tx_realloc is used by both common layer and bus layer. This patch
moves it to interface structure brcmf_bus as part of the fullmac
bus interface refactoring.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: move dongle statistics to struct brcmf_bus

Dongle statistics are shared data between common layer and bus
layer. This patch places them in bus interface structure brcmf_bus
as part of the fullmac bus interface refactoring.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: remove duplicate statistics from driver data structure

Some dongle statistics are stored in two places and synced when net
device status inquired. There is no need to do it this way any more.
Direct all usage to dongle stats structure in order to increase
readability.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: move driver up status to struct brcmf_bus

Driver up/down status to network interface need to be shared by
common layer and bus layer. Move it to bus interface structure
brcmf_bus as part of the fullmac bus interface refactoring.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: move maxctl to struct brcmf_bus

maxctl is the max size of rxctl request from protocol layer to bus
layer. Move it to bus interface structure brcmf_bus. This is part
of the fullmac bus interface refactoring.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: move sdio used statistics to struct brcmf_sdio

Some statistics only used by sdio modules. Move them to sdio layer
private structure brcmf_sdio. This is part of the fullmac bus
interface refactoring.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: change function proto_hdrpull parameter

Change parameter to device pointer for bus layer interface function
brcmf_proto_hdrpull This is part of the fullmac bus interface
refactoring.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: change function rx_frame parameter

Change parameter to device pointer for bus layer interface function
brcmf_rx_frame. This is part of the fullmac bus interface
refactoring.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: change function brcmf_c_prec_enq parameter

Change parameter to device pointer for bus layer interface function
brcmf_c_prec_enq. This is part of the fullmac bus interface
refactoring.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: change function txcomplete parameter

Change parameter to device pointer for bus layer interface function
brcmf_txcomplete. This is part of the fullmac bus interface
refactoring.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: change function txflowcontrol parameter

Change parameter to device pointer for bus layer interface function
brcmf_txflowcontrol. This is part of the fullmac bus interface
refactoring.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: change function brcmf_detach parameter

Change parameter to device pointer for bus layer interface function
brcmf_detach. This is part of the fullmac bus interface refactoring.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: change function bus_start parameter

Change parameter to device pointer for bus layer interface function
brcmf_bus_start. This is part of the fullmac bus interface
refactoring.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: change function add_if parameter

Change parameter to device pointer for bus layer interface function
brcmf_add_if. This is part of the fullmac bus interface
refactoring.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: register a dummy irq handler for SDIO function 2

When there is data available in dongle for driver to fetch, an
interrupt will be triggered and both SDIO function 1 and 2 will be
flagged by default in bcm4329. These two interrupt flags are
identical and only need to be handled once. Since there is no way
to turn off one flag from the dongle side, a dummy handler for
function 2 interrupt is placed.

Reported-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: remove oneline proto block functions

brcmf_os_proto_block and brcmf_os_proto_unblock are oneline
functions handling proto_block mutex. Place the mutex interface
call inline to increase readability.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcm80211: fmac: unify common layer driver data structure

No need to split data structure for common layer into brcmf_pub and
brcmf_info. Absorb brcmf_info into brcmf_pub to increase code
readability.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NFC: use kfree_skb() for sk_buffs

This is a struct sk_buff pointer and it should be freed with kfree_skb()
instead of kfree().

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NFC: double unlock in nfc_llcp_recv_connect()

We unlock inside the if block on the other side of this if else
statement.  It could result in calling mutex_unlock() twice.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: avoid packet losses in the dma worker code.

Following Rafal request, we verified that on "modern" CPUs using one
or more workers is equivalent. Here is patch V3 that addresses the
packet loss bug in the dma engine using only one worker.

-------

This patch addresses a bug in the dma worker code that keeps draining
packets even when the hardware queues are full. In such cases packets
can not be passed down to the device and are erroneusly dropped by the
code.

This problem was already discussed here

http://www.mail-archive.com/b43-dev@lists.infradead.org/msg01413.html

and acknowledged by Michael.

Number of hardware queues is now defined in b43.h (B43_QOS_QUEUE_NUM).

Acknowledgements to Riccardo Paolillo <riccardo.paolillo@gmail.com> and
Michele Orru <michele.orru@hotmail.it>

Signed-off-by: Francesco Gringoli <francesco.gringoli@ing.unibs.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: handle SMPS action frames

When a peer changes SMPS state we should update
rate control so it doesn't have to detect it by
itself. It can't detect "dynamic" mode anyway
since that just requires rts-cts handshaking.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

NFC: Fix LLCP related build failure

llcp_mac routines should be static and inlined or build will fail with NFC
selected without LLCP.

This patch fixes:

LD [M]  net/nfc/nfc.o
net/nfc/netlink.o: In function `nfc_llcp_mac_is_down':
netlink.c:(.text+0x0): multiple definition of `nfc_llcp_mac_is_down'
net/nfc/core.o:(.text+0x0): first defined here
net/nfc/netlink.o: In function `nfc_llcp_mac_is_up':
netlink.c:(.text+0x10): multiple definition of `nfc_llcp_mac_is_up'
net/nfc/core.o:(.text+0x10): first defined here
net/nfc/af_nfc.o: In function `nfc_llcp_mac_is_down':
(.text+0x0): multiple definition of `nfc_llcp_mac_is_down'
net/nfc/core.o:(.text+0x0): first defined here
net/nfc/af_nfc.o: In function `nfc_llcp_mac_is_up':
(.text+0x10): multiple definition of `nfc_llcp_mac_is_up'
net/nfc/core.o:(.text+0x10): first defined here
net/nfc/rawsock.o: In function `nfc_llcp_mac_is_down':
rawsock.c:(.text+0x0): multiple definition of `nfc_llcp_mac_is_down'
net/nfc/core.o:(.text+0x0): first defined here
net/nfc/rawsock.o: In function `nfc_llcp_mac_is_up':
rawsock.c:(.text+0x10): multiple definition of `nfc_llcp_mac_is_up'
net/nfc/core.o:(.text+0x10): first defined here

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: cleanup work in scan.c

Scan type derived from IEEE80211_CHAN_PASSIVE_SCAN bit is a boolean
flag representing passive scanning. We should not again compare it
with driver specific macro MWIFIEX_SCAN_TYPE_PASSIVE to determine
passive or active scan. We can also avoid the use of local variable
by using the flag directly.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath: Convert ath_dbg(bar, ATH_DBG_<FOO>, to ath_dbg(bar, FOO

Add ATH_DBG_ to macros to shorten the uses and
reduce the line count.

Coalesce ath_dbg formats.
Add missing spaces to coalesced formats.
Add missing newline terminations to ath_dbg formats.
Align ath_dbg arguments where appropriate.
Standardize ath_dbg formats without periods.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: Return beacon loss count in station

If station info contains a beacon loss count, return
it to userspace.

Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: split addba retries in time

  Currently code allows three (HT_AGG_MAX_RETRIES) unanswered addba
requests. When this limit is reached aggregation is turned off for
given TID permanently. This doesn't seem right: three requests is
not that much, some 'blackout' can happen, but effect of it affects
whole connection indefinitely.
  This patch increases number of retries to 15. Also, when there have
been 3 or more retries it splits further retries apart by 15 seconds
instead of sending them in very short period of time.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'master' of git://git./linux/kernel/git/padovan/bluetooth-next

Merge branch 'for-linville' of git://github.com/kvalo/ath6kl

Merge branch 'wireless-next' of git://git./linux/kernel/git/iwlwifi/iwlwifi

Merge git://git./linux/kernel/git/padovan/bluetooth

Conflicts:
net/bluetooth/l2cap_core.c

Bluetooth: Add missing mgmt_confirm_name command definition

This patch adds the necessary structs for the Confirm Name command. This
ensures that the protocol definitions are up to date with the latest
mgmt specification. The actual implementation of the command will follow
in a later patch-set.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Fix mgmt_(block,unblock)_device opcodes

This patch fixes the opcodes of the Block/Unblock device commands to
match with what user-space expects and to confirm with the latest mgmt
specification. The reason the values were wrong was a missing Confirm
Name command definition (which will be added by a subsequent patch).

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Add missing confirm_name field to mgmt_ev_device_found

This patch adds a missing confirm_name field to mgmt_ev_device_found.
Support for setting the correct value for this field is not implemented
yet, but having it part of the struct definition ensures that user-space
gets correct sized device_found events and is thereby able to do at
least rudimentary parsing of them.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Revert "Bluetooth: Revert: Fix L2CAP connection establishment"

This reverts commit 4dff523a913197e3314c7b0d08734ab037709093.

It was reported that this patch cause issues when trying to connect to
legacy devices so reverting it.

Reported-by: David Fries <david@fries.net>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Clear RFCOMM session timer when disconnecting last channel

When the last RFCOMM data channel is closed, a timer is normally set
up to disconnect the control channel at a later time.  If the control
channel disconnect command is sent with the timer pending, the timer
needs to be cancelled.

If the timer is not cancelled in this situation, the reference
counting logic for the RFCOMM session does not work correctly when the
remote device closes the L2CAP connection.  The session is freed at
the wrong time, leading to a kernel panic.

Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Prevent uninitialized data access in L2CAP configuration

When configuring an ERTM or streaming mode connection, remote devices
are expected to send an RFC option in a successful config response.  A
misbehaving remote device might not send an RFC option, and the L2CAP
code should not access uninitialized data in this case.

Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Incoming ACL packets do not force active mode

Incoming sk_buffs always have bt_cb(skb)->force_active set to 0, so
it's misleading to use that value from the control block when calling
hci_conn_enter_active_mode() for incoming data. The destination socket
is not known in the HCI layer, so the force_active setting for each
socket isn't known either. Hard-coding the force_active parameter does
not change any behavior, but makes it obvious that incoming ACL data
never exits sniff mode.

Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Simplify num_comp_pkts_evt function

Simplify function and remove fourth level of indentation.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Add HCI Read Data Block Size function

Implement block size read function. Use different variables for
packet-based and block-based flow control.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Use correct struct for user_confirm_neg_reply

This patch fixes user_confirm_neg_reply to use the appropriate struct
for accessing the call parameters.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Update ordering and opcodes of mgmt messages

This patch updates the ordering and opcodes of mgmt messages to match
the latest API specification.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Add timer for automatically disabling the service cache

We do not want the service cache to be enabled indefinitely after
mgmt_read_info is called. To solve this a timer is added which will
automatically disable the cache if mgmt_set_dev_class isn't called
within 5 seconds of calling mgmt_read_info.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Move EIR and CoD update functions to a better position

Due to the upcoming addition of a service cache timer the functions to
update the EIR and CoD need to be higher up in mgmt.c in order to avoid
unnecessary forward-declarations. This patch simply moves code around
without any other changes in order to make subsequent patches more
readable.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Remove mgmt_set_service_cache

Instead of having an explicit service cache command we can make the mgmt
API simpler by implicitly enabling the cache when mgmt_read_info is
called for the first time and disabling it when mgmt_set_dev_class is
called.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Move mgmt_set_fast_connectable to the right location

Fast connectable is logically after the connectable property so that's
where it should show up in the code as well (it's also after connectable
in the settings bitfield).

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Update mgmt_read_info and related mgmt messages

This patch updates the mgmt_read_info and related messages to the latest
management API which uses a bitfield of settings instead of individual
boolean values.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Add ProFUSION's copyright

Add ProFUSION's copyright to some files I've been touching recently.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Use system workqueue to schedule power_on

hdev->workqueue should be only for rx/tx, so move this one out.

Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Remove work_add and work_del from hci_sysfs

As we run in process context now we don't need worqueue to add e del from
sysfs.

Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Use new alloc_workqueue()

Update hdev workqueue API usage to use the new interface, this new
interface also allow us to mark this workqueue as WQ_HIGHPRI, so now rx
and tx work gets higher priority when running.

Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: move power_off to system workqueue

hdev->workqueue will be only for for rx/tx/cmd processing, all other small
works should go to the system workqueue for now.

Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Change l2cap chan_list to use RCU

This list has much more reads than writes, so RCU makes senses here, also
it avoid deadlock against the socket lock.

Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: invert locking order in connect path

This move some checking code that was in l2cap_sock_connect() to
l2cap_chan_connect(). Thus we can invert the lock calls, i.e., call
lock_sock() before hci_dev_lock() to avoid a deadlock scenario.

Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: convert info timer to delayed_work

Another step of remove interrupt context from Bluetooth Core.
Use the system workqueue.

Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: convert tx_task to workqueue

This should simplify Bluetooth core processing a lot.

Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Move command task to workqueue

As part of the moving on all the Bluetooth processing to Process context.

Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Don't disable tasklets to call hdev->notify()

It's pointless, we aren't protecting anything since btusb_notify()
schedules a work to run, then all it operation happens without protection.
If protection is really needed here, we will fix it further.

Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>