Jesse Barnes [Fri, 10 Jan 2014 21:13:09 +0000 (13:13 -0800)]
drm/i915/bdw: make sure south port interrupts are enabled properly v2
We were apparently relying on the defaults on BDW, which resulted in no
hotplug or AUX interrupts. So be sure to call the ibx_irq_preinstall to
enable all interrupts.
v2: use preinstall instead of redundant SDIER write
References: https://bugs.freedesktop.org/show_bug.cgi?id=72834
References: https://bugs.freedesktop.org/show_bug.cgi?id=72833
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville Syrjälä [Tue, 7 Jan 2014 14:15:36 +0000 (16:15 +0200)]
drm/i915: Don't grab crtc mutexes in intel_modeset_gem_init()
When the pipe A force quirk is applied the code will attempt to grab
a crtc mutex during intel_modeset_setup_hw_state(). If we're already
holding all crtc mutexes this will obviously deadlock every time.
So instead of using drm_modeset_lock_all() just grab the
mode_config.mutex. This is enough to avoid the unlocked mutex warnings
from certain lower level functions.
The regression was introduced in:
commit
027476642811f8559cbe00ef6cc54db230e48a20
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Dec 2 11:08:06 2013 +0200
drm/i915: Take modeset locks around intel_modeset_setup_hw_state()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
[danvet: Add cc: stable since the offending commit has that, too.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Wed, 8 Jan 2014 13:12:27 +0000 (11:12 -0200)]
drm/i915: fix DDI PLLs HW state readout code
Properly zero the refcounts and crtc->ddi_pll_set so the previous HW
state doesn't affect the result of reading the current HW state.
This fixes WARNs about WRPLL refcount if we have an HDMI monitor on
HSW and then suspend/resume.
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=64379
Tested-by: Qingshuai Tian <qingshuai.tian@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Tue, 7 Jan 2014 08:24:31 +0000 (09:24 +0100)]
MAINTAINERS: Updates for drm/i915
Jani for co-maintainer!
Jani has been a really active bug-scrubber in the past few months.
I've asked him whether he wants to do this in a more official capacity
and he agreed. I've already chatted with Dave and Jesse and they
support this.
Note that everyone can't now just relax because "Jani will do all the
bug scrubbing" - au contraire expect more nagging and poking now that
we have more bandwidth.
Longer-term the plan is to share more of the maintainer duties, but we
need to fix up the infrastructure a bit first (like moving the git
repo to a common location).
While at it also add the newly set-up patchwork instance.
Cc: Dave Airlie <airlied@gmail.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Alexander van Heukelum [Sat, 28 Dec 2013 20:00:39 +0000 (21:00 +0100)]
Revert "drm/i915: assume all GM45 Acer laptops use inverted backlight PWM"
My Acer 8510TZ stops displaying anything when X starts with Linus' current
tree. I bisected it down to commit
ee1452d74584.
This patch reverts commit
ee1452d74584.
After the revert, everything works as before.
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Reported-by: Dylan Borg <borgdylan@hotmail.com> (for a Acer Extensa 5635Z)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ben Widawsky [Tue, 24 Dec 2013 23:18:54 +0000 (15:18 -0800)]
drm/i915/bdw: Flush system agent on gen8 also
gem_gtt_cpu_tlb seems to indicate that it is needed.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=72869
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Linus Torvalds [Sat, 4 Jan 2014 23:12:14 +0000 (15:12 -0800)]
Linux 3.13-rc7
Linus Torvalds [Fri, 3 Jan 2014 21:48:25 +0000 (13:48 -0800)]
Merge tag 'for-v3.13-fixes' of git://git.infradead.org/battery-2.6
Pull battery fixes from Anton Vorontsov:
"Two fixes:
- fix build error caused by max17042_battery conversion to the regmap
API.
- fix kernel oops when booting with wakeup_source_activate enabled"
* tag 'for-v3.13-fixes' of git://git.infradead.org/battery-2.6:
max17042_battery: Fix build errors caused by missing REGMAP_I2C config
power_supply: Fix Oops from NULL pointer dereference from wakeup_source_activate
Linus Torvalds [Fri, 3 Jan 2014 21:44:41 +0000 (13:44 -0800)]
Merge tag 'pm+acpi-3.13-rc7' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI and PM fixes and new device IDs from Rafael Wysocki:
"These commits, except for one, are regression fixes and the remaining
one fixes a divide error leading to a kernel panic. The majority of
the regressions fixed here were introduced during the 3.12 cycle, one
of them is from this cycle and one is older.
Specifics:
- VGA switcheroo was broken for some users as a result of the
ACPI-based PCI hotplug (ACPIPHP) changes in 3.12, because some
previously ignored hotplug events started to be handled. The fix
causes them to be ignored again.
- There are two more issues related to cpufreq's suspend/resume
handling changes from the 3.12 cycle addressed by Viresh Kumar's
fixes.
- intel_pstate triggers a divide error in a timer function if the
P-state information it needs is missing during initialization.
This leads to kernel panics on nested KVM clients and is fixed by
failing the initialization cleanly in those cases.
- PCI initalization code changes during the 3.9 cycle uncovered BIOS
issues related to ACPI wakeup notifications (some BIOSes send them
for devices that aren't supposed to support ACPI wakeup). Work
around them by installing an ACPI wakeup notify handler for all PCI
devices with ACPI support.
- The Calxeda cpuilde driver's probe function is tagged as __init,
which is incorrect and causes a section mismatch to occur during
build. Fix from Andre Przywara removes the __init tag from there.
- During the 3.12 cycle ACPIPHP started to print warnings about
missing _ADR for devices that legitimately don't have it. Fix from
Toshi Kani makes it only print the warnings where they make sense"
* tag 'pm+acpi-3.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPIPHP / radeon / nouveau: Fix VGA switcheroo problem related to hotplug
intel_pstate: Fail initialization if P-state information is missing
ARM/cpuidle: remove __init tag from Calxeda cpuidle probe function
PCI / ACPI: Install wakeup notify handlers for all PCI devs with ACPI
cpufreq: preserve user_policy across suspend/resume
cpufreq: Clean up after a failing light-weight initialization
ACPI / PCI / hotplug: Avoid warning when _ADR not present
Linus Torvalds [Thu, 2 Jan 2014 22:50:18 +0000 (14:50 -0800)]
Merge git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm bugfixes from Marcelo Tosatti.
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: nVMX: Unconditionally uninit the MMU on nested vmexit
KVM: x86: Fix APIC map calculation after re-enabling
Linus Torvalds [Thu, 2 Jan 2014 22:40:38 +0000 (14:40 -0800)]
Merge branch 'akpm' (incoming from Andrew)
Merge patches from Andrew Morton:
"Ten fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
epoll: do not take the nested ep->mtx on EPOLL_CTL_DEL
sh: add EXPORT_SYMBOL(min_low_pfn) and EXPORT_SYMBOL(max_low_pfn) to sh_ksyms_32.c
drivers/dma/ioat/dma.c: check DMA mapping error in ioat_dma_self_test()
mm/memory-failure.c: transfer page count from head page to tail page after split thp
MAINTAINERS: set up proper record for Xilinx Zynq
mm: remove bogus warning in copy_huge_pmd()
memcg: fix memcg_size() calculation
mm: fix use-after-free in sys_remap_file_pages
mm: munlock: fix deadlock in __munlock_pagevec()
mm: munlock: fix a bug where THP tail page is encountered
Jason Baron [Thu, 2 Jan 2014 20:58:54 +0000 (12:58 -0800)]
epoll: do not take the nested ep->mtx on EPOLL_CTL_DEL
The EPOLL_CTL_DEL path of epoll contains a classic, ab-ba deadlock.
That is, epoll_ctl(a, EPOLL_CTL_DEL, b, x), will deadlock with
epoll_ctl(b, EPOLL_CTL_DEL, a, x). The deadlock was introduced with
commmit
67347fe4e632 ("epoll: do not take global 'epmutex' for simple
topologies").
The acquistion of the ep->mtx for the destination 'ep' was added such
that a concurrent EPOLL_CTL_ADD operation would see the correct state of
the ep (Specifically, the check for '!list_empty(&f.file->f_ep_links')
However, by simply not acquiring the lock, we do not serialize behind
the ep->mtx from the add path, and thus may perform a full path check
when if we had waited a little longer it may not have been necessary.
However, this is a transient state, and performing the full loop
checking in this case is not harmful.
The important point is that we wouldn't miss doing the full loop
checking when required, since EPOLL_CTL_ADD always locks any 'ep's that
its operating upon. The reason we don't need to do lock ordering in the
add path, is that we are already are holding the global 'epmutex'
whenever we do the double lock. Further, the original posting of this
patch, which was tested for the intended performance gains, did not
perform this additional locking.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: Nathan Zimmer <nzimmer@sgi.com>
Cc: Eric Wong <normalperson@yhbt.net>
Cc: Nelson Elhage <nelhage@nelhage.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nobuhiro Iwamatsu [Thu, 2 Jan 2014 20:58:53 +0000 (12:58 -0800)]
sh: add EXPORT_SYMBOL(min_low_pfn) and EXPORT_SYMBOL(max_low_pfn) to sh_ksyms_32.c
Min_low_pfn and max_low_pfn were used in pfn_valid macro if defined
CONFIG_FLATMEM. When the functions that use the pfn_valid is used in
driver module, max_low_pfn and min_low_pfn is to undefined, and fail to
build.
ERROR: "min_low_pfn" [drivers/block/aoe/aoe.ko] undefined!
ERROR: "max_low_pfn" [drivers/block/aoe/aoe.ko] undefined!
make[2]: *** [__modpost] Error 1
make[1]: *** [modules] Error 2
This patch fix this problem.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@gmail.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiang Liu [Thu, 2 Jan 2014 20:58:52 +0000 (12:58 -0800)]
drivers/dma/ioat/dma.c: check DMA mapping error in ioat_dma_self_test()
Check DMA mapping return values in function ioat_dma_self_test() to get
rid of following warning message.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1203 at lib/dma-debug.c:937 check_unmap+0x4c0/0x9a0()
ioatdma 0000:00:04.0: DMA-API: device driver failed to check map error[device address=0x000000085191b000] [size=2000 bytes] [mapped as single]
Modules linked in: ioatdma(+) mac_hid wmi acpi_pad lp parport hidd_generic usbhid hid ixgbe isci dca libsas ahci ptp libahci scsi_transport_sas meegaraid_sas pps_core mdio
CPU: 0 PID: 1203 Comm: systemd-udevd Not tainted 3.13.0-rc4+ #8
Hardware name: Intel Corporation BRICKLAND/BRICKLAND, BIOS BRIVTIIN1.86B.0044.L09.
1311181644 11/18/2013
Call Trace:
dump_stack+0x4d/0x66
warn_slowpath_common+0x7d/0xa0
warn_slowpath_fmt+0x4c/0x50
check_unmap+0x4c0/0x9a0
debug_dma_unmap_page+0x81/0x90
ioat_dma_self_test+0x3d2/0x680 [ioatdma]
ioat3_dma_self_test+0x12/0x30 [ioatdma]
ioat_probe+0xf4/0x110 [ioatdma]
ioat3_dma_probe+0x268/0x410 [ioatdma]
ioat_pci_probe+0x122/0x1b0 [ioatdma]
local_pci_probe+0x45/0xa0
pci_device_probe+0xd9/0x130
driver_probe_device+0x171/0x490
__driver_attach+0x93/0xa0
bus_for_each_dev+0x6b/0xb0
driver_attach+0x1e/0x20
bus_add_driver+0x1f8/0x2b0
driver_register+0x81/0x110
__pci_register_driver+0x60/0x70
ioat_init_module+0x89/0x1000 [ioatdma]
do_one_initcall+0xe2/0x250
load_module+0x2313/0x2a00
SyS_init_module+0xd9/0x130
system_call_fastpath+0x1a/0x1f
---[ end trace
990c591681d27c31 ]---
Mapped at:
debug_dma_map_page+0xbe/0x180
ioat_dma_self_test+0x1ab/0x680 [ioatdma]
ioat3_dma_self_test+0x12/0x30 [ioatdma]
ioat_probe+0xf4/0x110 [ioatdma]
ioat3_dma_probe+0x268/0x410 [ioatdma]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Naoya Horiguchi [Thu, 2 Jan 2014 20:58:51 +0000 (12:58 -0800)]
mm/memory-failure.c: transfer page count from head page to tail page after split thp
Memory failures on thp tail pages cause kernel panic like below:
mce: [Hardware Error]: Machine check events logged
MCE exception done on CPU 7
BUG: unable to handle kernel NULL pointer dereference at
0000000000000058
IP: [<
ffffffff811b7cd1>] dequeue_hwpoisoned_huge_page+0x131/0x1e0
PGD
bae42067 PUD
ba47d067 PMD 0
Oops: 0000 [#1] SMP
...
CPU: 7 PID: 128 Comm: kworker/7:2 Tainted: G M O
3.13.0-rc4-131217-1558-00003-g83b7df08e462 #25
...
Call Trace:
me_huge_page+0x3e/0x50
memory_failure+0x4bb/0xc20
mce_process_work+0x3e/0x70
process_one_work+0x171/0x420
worker_thread+0x11b/0x3a0
? manage_workers.isra.25+0x2b0/0x2b0
kthread+0xe4/0x100
? kthread_create_on_node+0x190/0x190
ret_from_fork+0x7c/0xb0
? kthread_create_on_node+0x190/0x190
...
RIP dequeue_hwpoisoned_huge_page+0x131/0x1e0
CR2:
0000000000000058
The reasoning of this problem is shown below:
- when we have a memory error on a thp tail page, the memory error
handler grabs a refcount of the head page to keep the thp under us.
- Before unmapping the error page from processes, we split the thp,
where page refcounts of both of head/tail pages don't change.
- Then we call try_to_unmap() over the error page (which was a tail
page before). We didn't pin the error page to handle the memory error,
this error page is freed and removed from LRU list.
- We never have the error page on LRU list, so the first page state
check returns "unknown page," then we move to the second check
with the saved page flag.
- The saved page flag have PG_tail set, so the second page state check
returns "hugepage."
- We call me_huge_page() for freed error page, then we hit the above panic.
The root cause is that we didn't move refcount from the head page to the
tail page after split thp. So this patch suggests to do this.
This panic was introduced by commit
524fca1e73 ("HWPOISON: fix
misjudgement of page_action() for errors on mlocked pages"). Note that we
did have the same refcount problem before this commit, but it was just
ignored because we had only first page state check which returned "unknown
page." The commit changed the refcount problem from "doesn't work" to
"kernel panic."
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reviewed-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: <stable@vger.kernel.org> [3.9+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Simek [Thu, 2 Jan 2014 20:58:50 +0000 (12:58 -0800)]
MAINTAINERS: set up proper record for Xilinx Zynq
Setup correct zynq entry.
- Add missing cadence_ttc_timer maintainership
- Add zynq wildcard
- Add xilinx wildcard
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mel Gorman [Thu, 2 Jan 2014 20:58:49 +0000 (12:58 -0800)]
mm: remove bogus warning in copy_huge_pmd()
Sasha Levin reported the following warning being triggered
WARNING: CPU: 28 PID: 35287 at mm/huge_memory.c:887 copy_huge_pmd+0x145/ 0x3a0()
Call Trace:
copy_huge_pmd+0x145/0x3a0
copy_page_range+0x3f2/0x560
dup_mmap+0x2c9/0x3d0
dup_mm+0xad/0x150
copy_process+0xa68/0x12e0
do_fork+0x96/0x270
SyS_clone+0x16/0x20
stub_clone+0x69/0x90
This warning was introduced by "mm: numa: Avoid unnecessary disruption
of NUMA hinting during migration" for paranoia reasons but the warning
is bogus. I was thinking of parallel races between NUMA hinting faults
and forks but this warning would also be triggered by a parallel reclaim
splitting a THP during a fork. Remote the bogus warning.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vladimir Davydov [Thu, 2 Jan 2014 20:58:47 +0000 (12:58 -0800)]
memcg: fix memcg_size() calculation
The mem_cgroup structure contains nr_node_ids pointers to
mem_cgroup_per_node objects, not the objects themselves.
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Glauber Costa <glommer@openvz.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rik van Riel [Thu, 2 Jan 2014 20:58:46 +0000 (12:58 -0800)]
mm: fix use-after-free in sys_remap_file_pages
remap_file_pages calls mmap_region, which may merge the VMA with other
existing VMAs, and free "vma". This can lead to a use-after-free bug.
Avoid the bug by remembering vm_flags before calling mmap_region, and
not trying to dereference vma later.
Signed-off-by: Rik van Riel <riel@redhat.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: PaX Team <pageexec@freemail.hu>
Cc: Kees Cook <keescook@chromium.org>
Cc: Michel Lespinasse <walken@google.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vlastimil Babka [Thu, 2 Jan 2014 20:58:44 +0000 (12:58 -0800)]
mm: munlock: fix deadlock in __munlock_pagevec()
Commit
7225522bb429 ("mm: munlock: batch non-THP page isolation and
munlock+putback using pagevec" introduced __munlock_pagevec() to speed
up munlock by holding lru_lock over multiple isolated pages. Pages that
fail to be isolated are put_page()d immediately, also within the lock.
This can lead to deadlock when __munlock_pagevec() becomes the holder of
the last page pin and put_page() leads to __page_cache_release() which
also locks lru_lock. The deadlock has been observed by Sasha Levin
using trinity.
This patch avoids the deadlock by deferring put_page() operations until
lru_lock is released. Another pagevec (which is also used by later
phases of the function is reused to gather the pages for put_page()
operation.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vlastimil Babka [Thu, 2 Jan 2014 20:58:43 +0000 (12:58 -0800)]
mm: munlock: fix a bug where THP tail page is encountered
Since commit
ff6a6da60b89 ("mm: accelerate munlock() treatment of THP
pages") munlock skips tail pages of a munlocked THP page. However, when
the head page already has PageMlocked unset, it will not skip the tail
pages.
Commit
7225522bb429 ("mm: munlock: batch non-THP page isolation and
munlock+putback using pagevec") has added a PageTransHuge() check which
contains VM_BUG_ON(PageTail(page)). Sasha Levin found this triggered
using trinity, on the first tail page of a THP page without PageMlocked
flag.
This patch fixes the issue by skipping tail pages also in the case when
PageMlocked flag is unset. There is still a possibility of race with
THP page split between clearing PageMlocked and determining how many
pages to skip. The race might result in former tail pages not being
skipped, which is however no longer a bug, as during the skip the
PageTail flags are cleared.
However this race also affects correctness of NR_MLOCK accounting, which
is to be fixed in a separate patch.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Bob Liu <bob.liu@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 2 Jan 2014 20:45:47 +0000 (12:45 -0800)]
Merge tag 'gfs2-fixes' of git://git./linux/kernel/git/steve/gfs2-3.0-fixes
Pull GFS2 fixes from Steven Whitehouse:
"Here is a set of small fixes for GFS2. There is a fix to drop
s_umount which is copied in from the core vfs, two patches relate to a
hard to hit "use after free" and memory leak. Two patches related to
using DIO and buffered I/O on the same file to ensure correct
operation in relation to glock state changes. The final patch adds an
RCU read lock to ensure correct locking on an error path"
* tag 'gfs2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes:
GFS2: Fix unsafe dereference in dump_holder()
GFS2: Wait for async DIO in glock state changes
GFS2: Fix incorrect invalidation for DIO/buffered I/O
GFS2: Fix slab memory leak in gfs2_bufdata
GFS2: Fix use-after-free race when calling gfs2_remove_from_ail
GFS2: don't hold s_umount over blkdev_put
Linus Torvalds [Thu, 2 Jan 2014 20:45:07 +0000 (12:45 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"Two small bug fixes and a follow-up to the CONFIG_NR_CPUS change.
A kernel compiled with CONFIG_NR_CPUS=256 will waste quite a bit of
memory for the per-cpu arrays. Under z/VM the maximum number of CPUs
is 64, the code now limits the possible cpu mask to 64 if running
under z/VM"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pci: obtain function handle in hotplug notifier
s390/3270: fix allocation of tty3270_screen structure
s390/smp: improve setup of possible cpu mask
Jan Kiszka [Sat, 28 Dec 2013 15:31:52 +0000 (16:31 +0100)]
KVM: nVMX: Unconditionally uninit the MMU on nested vmexit
Three reasons for doing this: 1. arch.walk_mmu points to arch.mmu anyway
in case nested EPT wasn't in use. 2. this aligns VMX with SVM. But 3. is
most important: nested_cpu_has_ept(vmcs12) queries the VMCS page, and if
one guest VCPU manipulates the page of another VCPU in L2, we may be
fooled to skip over the nested_ept_uninit_mmu_context, leaving mmu in
nested state. That can crash the host later on if nested_ept_get_cr3 is
invoked while L1 already left vmxon and nested.current_vmcs12 became
NULL therefore.
Cc: stable@kernel.org
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Tetsuo Handa [Thu, 2 Jan 2014 10:52:20 +0000 (19:52 +0900)]
GFS2: Fix unsafe dereference in dump_holder()
GLOCK_BUG_ON() might call this function without RCU read lock. Make sure that
RCU read lock is held when using task_struct returned from pid_task().
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Linus Torvalds [Wed, 1 Jan 2014 19:36:16 +0000 (11:36 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull radeon drm fixes from Dave Airlie:
"Just piping a bunch of fixes from pre-xmas from Alex for radeon, all
either fix bad hw setup issues or regressions"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: Bump version for CIK DCE tiling fix
drm/radeon: set correct number of banks for CIK chips in DCE
drm/radeon: set correct pipe config for Hawaii in DCE
drm/radeon: expose render backend mask to the userspace
drm/radeon: fix render backend setup for SI and CIK
drm/radeon: 0x9649 is SUMO2 not SUMO
drm/radeon: fix UVD 256MB check
Linus Torvalds [Wed, 1 Jan 2014 19:35:27 +0000 (11:35 -0800)]
Merge git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"Fix a build error on ARM that was introduced in 3.13-rc1"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: ixp4xx - Fix kernel compile error
Dave Airlie [Wed, 1 Jan 2014 10:32:19 +0000 (20:32 +1000)]
Merge branch 'drm-fixes-3.13' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Radeon fixes, Christmas eve edition. Fix incorrect family for 0x9649
which lead to bogus rendering, tiling and RB fixes for SI and CIK,
and a UVD fix.
* 'drm-fixes-3.13' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: Bump version for CIK DCE tiling fix
drm/radeon: set correct number of banks for CIK chips in DCE
drm/radeon: set correct pipe config for Hawaii in DCE
drm/radeon: expose render backend mask to the userspace
drm/radeon: fix render backend setup for SI and CIK
drm/radeon: 0x9649 is SUMO2 not SUMO
drm/radeon: fix UVD 256MB check
Krzysztof Hałasa [Tue, 31 Dec 2013 10:51:16 +0000 (11:51 +0100)]
crypto: ixp4xx - Fix kernel compile error
drivers/crypto/ixp4xx_crypto.c: In function 'ixp_module_init':
drivers/crypto/ixp4xx_crypto.c:1419:2: error: 'dev' undeclared (first use in this function)
Now builds. Not tested on real hw.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Rafael J. Wysocki [Tue, 31 Dec 2013 21:09:28 +0000 (22:09 +0100)]
Merge branches 'pm-cpufreq' and 'pm-cpuidle'
* pm-cpufreq:
intel_pstate: Fail initialization if P-state information is missing
cpufreq: preserve user_policy across suspend/resume
cpufreq: Clean up after a failing light-weight initialization
* pm-cpuidle:
ARM/cpuidle: remove __init tag from Calxeda cpuidle probe function
Rafael J. Wysocki [Tue, 31 Dec 2013 21:08:08 +0000 (22:08 +0100)]
Merge branch 'cpuidle/3.13-fixes' of git://git.linaro.org/people/daniel.lezcano/linux into pm-cpuidle
Pull ARM cpuidle fixes for v3.13 from Daniel Lezcano.
* 'cpuidle/3.13-fixes' of git://git.linaro.org/people/daniel.lezcano/linux:
ARM/cpuidle: remove __init tag from Calxeda cpuidle probe function
Rafael J. Wysocki [Tue, 31 Dec 2013 21:03:37 +0000 (22:03 +0100)]
Merge branches 'acpi-pci-pm' and 'acpi-pci-hotplug'
* acpi-pci-pm:
PCI / ACPI: Install wakeup notify handlers for all PCI devs with ACPI
* acpi-pci-hotplug:
ACPIPHP / radeon / nouveau: Fix VGA switcheroo problem related to hotplug
ACPI / PCI / hotplug: Avoid warning when _ADR not present
Linus Torvalds [Tue, 31 Dec 2013 20:19:30 +0000 (12:19 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
"A fix for a panic in gpio-keys driver when set up with absolute
events, a fixup to the new zforce driver and a new keycode definition"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: allocate absinfo data when setting ABS capability
Input: define KEY_WWAN for Wireless WAN
Input: zforce - fix possible driver hang during suspend
Linus Torvalds [Tue, 31 Dec 2013 20:17:14 +0000 (12:17 -0800)]
Merge branch 'for-linus' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"A few small cifs fixes including two for stable, and fixing a
regression introduced by the VFS change to file create"
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
cifs: set FILE_CREATED
cifs: We do not drop reference to tlink in CIFSCheckMFSymlink()
Add missing end of line termination to some cifs messages
Dmitry Torokhov [Fri, 27 Dec 2013 01:44:29 +0000 (17:44 -0800)]
Input: allocate absinfo data when setting ABS capability
We need to make sure we allocate absinfo data when we are setting one of
EV_ABS/ABS_XXX capabilities, otherwise we may bomb when we try to emit this
event.
Rested-by: Paul Cercueil <pcercuei@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Rafael J. Wysocki [Tue, 31 Dec 2013 12:39:42 +0000 (13:39 +0100)]
ACPIPHP / radeon / nouveau: Fix VGA switcheroo problem related to hotplug
The changes in the ACPI-based PCI hotplug (ACPIPHP) subsystem made
during the 3.12 development cycle uncovered a problem with VGA
switcheroo that on some systems, when the device-specific method
(ATPX in the radeon case, _DSM in the nouveau case) is used to turn
off the discrete graphics, the BIOS generates ACPI hotplug events for
that device and those events cause ACPIPHP to attempt to remove the
device from the system (they are events for a device that was present
previously and is not present any more, so that's what should be done
according to the spec). Then, the system stops functioning correctly.
Since the hotplug events in question were simply silently ignored
previously, the least intrusive way to address that problem is to
make ACPIPHP ignore them again. For this purpose, introduce a new
ACPI device flag, no_hotplug, and modify ACPIPHP to ignore hotplug
events for PCI devices whose ACPI companions have that flag set.
Next, make the radeon and nouveau switcheroo detection code set the
no_hotplug flag for the discrete graphics' ACPI companion.
Fixes: bbd34fcdd1b2 (ACPI / hotplug / PCI: Register all devices under the given bridge)
References: https://bugzilla.kernel.org/show_bug.cgi?id=61891
References: https://bugzilla.kernel.org/show_bug.cgi?id=64891
Reported-and-tested-by: Mike Lothian <mike@fireburn.co.uk>
Reported-and-tested-by: <madcatx@atlas.cz>
Reported-and-tested-by: Joaquín Aramendía <samsagax@gmail.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
Rafael J. Wysocki [Tue, 31 Dec 2013 12:37:46 +0000 (13:37 +0100)]
intel_pstate: Fail initialization if P-state information is missing
If pstate.current_pstate is 0 after the initial
intel_pstate_get_cpu_pstates(), this means that we were unable to
obtain any useful P-state information and there is no reason to
continue, so free memory and return an error in that case.
This fixes the following divide error occuring in a nested KVM
guest:
Intel P-state driver initializing.
Intel pstate controlling: cpu 0
cpufreq: __cpufreq_add_dev: ->get() failed
divide error: 0000 [#1] SMP
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.13.0-0.rc4.git5.1.fc21.x86_64 #1
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
task:
ffff88001ea20000 ti:
ffff88001e9bc000 task.ti:
ffff88001e9bc000
RIP: 0010:[<
ffffffff815c551d>] [<
ffffffff815c551d>] intel_pstate_timer_func+0x11d/0x2b0
RSP: 0000:
ffff88001ee03e18 EFLAGS:
00010246
RAX:
0000000000000000 RBX:
ffff88001a454348 RCX:
0000000000006100
RDX:
0000000000000000 RSI:
0000000000000000 RDI:
0000000000000000
RBP:
ffff88001ee03e38 R08:
0000000000000000 R09:
0000000000000000
R10:
ffff88001ea20000 R11:
0000000000000000 R12:
00000c0a1ea20000
R13:
1ea200001ea20000 R14:
ffffffff815c5400 R15:
ffff88001a454348
FS:
0000000000000000(0000) GS:
ffff88001ee00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
000000008005003b
CR2:
0000000000000000 CR3:
0000000001c0c000 CR4:
00000000000006f0
Stack:
fffffffb1a454390 ffffffff821a4500 ffff88001a454390 0000000000000100
ffff88001ee03ea8 ffffffff81083e9a ffffffff81083e15 ffffffff82d5ed40
ffffffff8258cc60 0000000000000000 ffffffff81ac39de 0000000000000000
Call Trace:
<IRQ>
[<
ffffffff81083e9a>] call_timer_fn+0x8a/0x310
[<
ffffffff81083e15>] ? call_timer_fn+0x5/0x310
[<
ffffffff815c5400>] ? pid_param_set+0x130/0x130
[<
ffffffff81084354>] run_timer_softirq+0x234/0x380
[<
ffffffff8107aee4>] __do_softirq+0x104/0x430
[<
ffffffff8107b5fd>] irq_exit+0xcd/0xe0
[<
ffffffff81770645>] smp_apic_timer_interrupt+0x45/0x60
[<
ffffffff8176efb2>] apic_timer_interrupt+0x72/0x80
<EOI>
[<
ffffffff810e15cd>] ? vprintk_emit+0x1dd/0x5e0
[<
ffffffff81757719>] printk+0x67/0x69
[<
ffffffff815c1493>] __cpufreq_add_dev.isra.13+0x883/0x8d0
[<
ffffffff815c14f0>] cpufreq_add_dev+0x10/0x20
[<
ffffffff814a14d1>] subsys_interface_register+0xb1/0xf0
[<
ffffffff815bf5cf>] cpufreq_register_driver+0x9f/0x210
[<
ffffffff81fb19af>] intel_pstate_init+0x27d/0x3be
[<
ffffffff81761e3e>] ? mutex_unlock+0xe/0x10
[<
ffffffff81fb1732>] ? cpufreq_gov_dbs_init+0x12/0x12
[<
ffffffff8100214a>] do_one_initcall+0xfa/0x1b0
[<
ffffffff8109dbf5>] ? parse_args+0x225/0x3f0
[<
ffffffff81f64193>] kernel_init_freeable+0x1fc/0x287
[<
ffffffff81f638d0>] ? do_early_param+0x88/0x88
[<
ffffffff8174b530>] ? rest_init+0x150/0x150
[<
ffffffff8174b53e>] kernel_init+0xe/0x130
[<
ffffffff8176e27c>] ret_from_fork+0x7c/0xb0
[<
ffffffff8174b530>] ? rest_init+0x150/0x150
Code: c1 e0 05 48 63 bc 03 10 01 00 00 48 63 83 d0 00 00 00 48 63 d6 48 c1 e2 08 c1 e1 08 4c 63 c2 48 c1 e0 08 48 98 48 c1 e0 08 48 99 <49> f7 f8 48 98 48 0f af f8 48 c1 ff 08 29 f9 89 ca c1 fa 1f 89
RIP [<
ffffffff815c551d>] intel_pstate_timer_func+0x11d/0x2b0
RSP <
ffff88001ee03e18>
---[ end trace
f166110ed22cc37a ]---
Kernel panic - not syncing: Fatal exception in interrupt
Reported-and-tested-by: Kashyap Chamarthy <kchamart@redhat.com>
Cc: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: All applicable <stable@vger.kernel.org>
Linus Torvalds [Mon, 30 Dec 2013 22:31:11 +0000 (14:31 -0800)]
Merge tag 'dt-fixes-for-3.13' of git://git./linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Fix 2 regressions found on PPC
- Allow NULL ptr in unflatten_and_copy_device_tree
- Update my email address
* tag 'dt-fixes-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
MAINTAINERS: Update Rob Herring's email address
of/irq: Fix device_node refcount in of_irq_parse_raw()
of/Kconfig: Spelling s/one/once/
Revert "of/address: Handle #address-cells > 2 specially"
of: Fix NULL dereference in unflatten_and_copy()
Jan Kiszka [Sun, 29 Dec 2013 01:29:30 +0000 (02:29 +0100)]
KVM: x86: Fix APIC map calculation after re-enabling
Update arch.apic_base before triggering recalculate_apic_map. Otherwise
the recalculation will work against the previous state of the APIC and
will fail to build the correct map when an APIC is hardware-enabled
again.
This fixes a regression of
1e08ec4a13.
Cc: stable@vger.kernel.org
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Linus Torvalds [Mon, 30 Dec 2013 18:22:57 +0000 (10:22 -0800)]
Merge branch 'merge' of git://git./linux/kernel/git/benh/powerpc
Pull powerpc fixes from Ben Herrenschmidt:
"A bit more endian problems found during testing of 3.13 and a few
other simple fixes and regressions fixes"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix alignment of secondary cpu spin vars
powerpc: Align p_end
powernv/eeh: Add buffer for P7IOC hub error data
powernv/eeh: Fix possible buffer overrun in ioda_eeh_phb_diag()
powerpc: Make 64-bit non-VMX __copy_tofrom_user bi-endian
powerpc: Make unaligned accesses endian-safe for powerpc
powerpc: Fix bad stack check in exception entry
powerpc/512x: dts: disable MPC5125 usb module
powerpc/512x: dts: remove misplaced IRQ spec from 'soc' node (5125)
Rob Herring [Mon, 30 Dec 2013 18:09:47 +0000 (12:09 -0600)]
Merge remote-tracking branch 'grant/devicetree/merge' into dt-fixes
Linus Torvalds [Mon, 30 Dec 2013 17:33:30 +0000 (09:33 -0800)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
"Some holiday bug fixes for 3.13... There is still one bug I'd like to
get fixed before 3.13-final.
The vlan code erroneously assignes the header ops of the underlying
real device to the VLAN device above it when the real device can
hardware offload VLAN handling. That's completely bogus because
header ops are tied to the device type, so they only expect to see a
'dev' argument compatible with their ops.
The fix is the have the VLAN code use a special set of header ops that
does the pass-thru correctly, by calling the underlying real device's
header ops but _also_ passing in the real device instead of the VLAN
device.
That fix is currently waiting some testing.
Anyways, of note here:
1) Fix bitmap edge case in radiotap, from Johannes Berg.
2) Fix oops on driver unload in rtlwifi, from Larry Finger.
3) Bonding doesn't do locking correctly during speed/duplex/link
changes, from Ding Tianhong.
4) Fix header parsing in GRE code, this bug has been around for a few
releases. From Timo Teräs.
5) SIT tunnel driver MTU check needs to take GSO into account, from
Eric Dumazet.
6) Minor info leak in inet_diag, from Daniel Borkmann.
7) Info leak in YAM hamradio driver, from Salva Peiró.
8) Fix route expiration state handling in ipv6 routing code, from Li
RongQing.
9) DCCP probe module does not check request_module()'s return value,
from Wang Weidong.
10) cpsw driver passes NULL device names to request_irq(), from
Mugunthan V N.
11) Prevent a NULL splat in RDS binding code, from Sasha Levin.
12) Fix 4G overflow test in tg3 driver, from Nithin Sujir.
13) Cure use after free in arc_emac and fec driver's software
timestamp handling, from Eric Dumazet.
14) SIT driver can fail to release the route when
iptunnel_handle_offloads() throws an error. From Li RongQing.
15) Several batman-adv fixes from Simon Wunderlich and Antonio
Quartulli.
16) Fix deadlock during TIPC socket release, from Ying Xue.
17) Fix regression in ROSE protocol recvmsg() msg_name handling, from
Florian Westphal.
18) stmmac PTP support releases wrong spinlock, from Vince Bridgers"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (73 commits)
stmmac: Fix incorrect spinlock release and PTP cap detection.
phy: IRQ cannot be shared
net: rose: restore old recvmsg behavior
xen-netback: fix guest-receive-side array sizes
fec: Do not assume that PHY reset is active low
tipc: fix deadlock during socket release
netfilter: nf_tables: fix wrong datatype in nft_validate_data_load()
batman-adv: fix vlan header access
batman-adv: clean nf state when removing protocol header
batman-adv: fix alignment for batadv_tvlv_tt_change
batman-adv: fix size of batadv_bla_claim_dst
batman-adv: fix size of batadv_icmp_header
batman-adv: fix header alignment by unrolling batadv_header
batman-adv: fix alignment for batadv_coded_packet
netfilter: nf_tables: fix oops when updating table with user chains
netfilter: nf_tables: fix dumping with large number of sets
ipv6: release dst properly in ipip6_tunnel_xmit
netxen: Correct off-by-one errors in bounds checks
net: Add some clarification to skb_tx_timestamp() comment.
arc_emac: fix potential use after free
...
Rob Herring [Tue, 3 Dec 2013 16:20:16 +0000 (10:20 -0600)]
MAINTAINERS: Update Rob Herring's email address
My Calxeda email address is going away.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Cédric Le Goater [Tue, 17 Dec 2013 17:32:53 +0000 (18:32 +0100)]
of/irq: Fix device_node refcount in of_irq_parse_raw()
Commit
2361613206e6, "of/irq: Refactor interrupt-map parsing" changed
the refcount on the device_node causing an error in of_node_put():
ERROR: Bad of_node_put() on /pci@
800000020000000
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.13.0-rc3-dirty #2
Call Trace:
[
c00000003e403500] [
c0000000000144fc] .show_stack+0x7c/0x1f0 (unreliable)
[
c00000003e4035d0] [
c00000000070f250] .dump_stack+0x88/0xb4
[
c00000003e403650] [
c0000000005e8768] .of_node_release+0xd8/0xf0
[
c00000003e4036e0] [
c0000000005eeafc] .of_irq_parse_one+0x10c/0x280
[
c00000003e4037a0] [
c0000000005efd4c] .of_irq_parse_pci+0x3c/0x1d0
[
c00000003e403840] [
c000000000038240] .pcibios_setup_device+0xa0/0x2e0
[
c00000003e403910] [
c0000000000398f0] .pcibios_setup_bus_devices+0x60/0xd0
[
c00000003e403990] [
c00000000003b3a4] .__of_scan_bus+0x1a4/0x2b0
[
c00000003e403a80] [
c00000000003a62c] .pcibios_scan_phb+0x30c/0x410
[
c00000003e403b60] [
c0000000009fe430] .pcibios_init+0x7c/0xd4
This patch adjusts the refcount in the walk of the interrupt tree.
When a match is found, there is no need to increase the refcount
on 'out_irq->np' as 'newpar' is already holding a ref. The refcount
balance between 'ipar' and 'newpar' is maintained in the skiplevel:
goto label.
This patch also removes the usage of the device_node variable 'old'
which seems useless after the latest changes.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Geert Uytterhoeven [Tue, 24 Dec 2013 20:06:01 +0000 (21:06 +0100)]
of/Kconfig: Spelling s/one/once/
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Rob Herring [Mon, 30 Dec 2013 01:37:43 +0000 (19:37 -0600)]
Revert "of/address: Handle #address-cells > 2 specially"
This reverts commit
e38c0a1fbc5803cbacdaac0557c70ac8ca5152e7.
Nikita Yushchenko reports:
While trying to make freescale p2020ds and mpc8572ds boards working
with mainline kernel, I faced that commit
e38c0a1f (Handle
Both these boards have uli1575 chip.
Corresponding part in device tree is something like
uli1575@0 {
reg = <0x0 0x0 0x0 0x0 0x0>;
#size-cells = <2>;
#address-cells = <3>;
ranges = <0x2000000 0x0 0x80000000
0x2000000 0x0 0x80000000
0x0 0x20000000
0x1000000 0x0 0x0
0x1000000 0x0 0x0
0x0 0x10000>;
isa@1e {
...
I.e. it has #address-cells = <3>
With commit
e38c0a1f reverted, devices under uli1575 are registered
correctly, e.g. for rtc
OF: ** translation for device /pcie@
ffe09000/pcie@0/uli1575@0/isa@1e/rtc@70 **
OF: bus is isa (na=2, ns=1) on /pcie@
ffe09000/pcie@0/uli1575@0/isa@1e
OF: translating address:
00000001 00000070
OF: parent bus is default (na=3, ns=2) on /pcie@
ffe09000/pcie@0/uli1575@0
OF: walking ranges...
OF: ISA map, cp=0, s=1000, da=70
OF: parent translation for:
01000000 00000000 00000000
OF: with offset: 70
OF: one level translation:
00000000 00000000 00000070
OF: parent bus is pci (na=3, ns=2) on /pcie@
ffe09000/pcie@0
OF: walking ranges...
OF: default map, cp=
a0000000, s=
20000000, da=70
OF: default map, cp=0, s=10000, da=70
OF: parent translation for:
01000000 00000000 00000000
OF: with offset: 70
OF: one level translation:
01000000 00000000 00000070
OF: parent bus is pci (na=3, ns=2) on /pcie@
ffe09000
OF: walking ranges...
OF: PCI map, cp=0, s=10000, da=70
OF: parent translation for:
01000000 00000000 00000000
OF: with offset: 70
OF: one level translation:
01000000 00000000 00000070
OF: parent bus is default (na=2, ns=2) on /
OF: walking ranges...
OF: PCI map, cp=0, s=10000, da=70
OF: parent translation for:
00000000 ffc10000
OF: with offset: 70
OF: one level translation:
00000000 ffc10070
OF: reached root node
With commit
e38c0a1f in place, address translation fails:
OF: ** translation for device /pcie@
ffe09000/pcie@0/uli1575@0/isa@1e/rtc@70 **
OF: bus is isa (na=2, ns=1) on /pcie@
ffe09000/pcie@0/uli1575@0/isa@1e
OF: translating address:
00000001 00000070
OF: parent bus is default (na=3, ns=2) on /pcie@
ffe09000/pcie@0/uli1575@0
OF: walking ranges...
OF: ISA map, cp=0, s=1000, da=70
OF: parent translation for:
01000000 00000000 00000000
OF: with offset: 70
OF: one level translation:
00000000 00000000 00000070
OF: parent bus is pci (na=3, ns=2) on /pcie@
ffe09000/pcie@0
OF: walking ranges...
OF: default map, cp=
a0000000, s=
20000000, da=70
OF: default map, cp=0, s=10000, da=70
OF: not found !
Thierry Reding confirmed this commit was not needed after all:
"We ended up merging a different address representation for Tegra PCIe
and I've confirmed that reverting this commit doesn't cause any obvious
regressions. I think all other drivers in drivers/pci/host ended up
copying what we did on Tegra, so I wouldn't expect any other breakage
either."
There doesn't appear to be a simple way to support both behaviours, so
reverting this as nothing should be depending on the new behaviour.
Cc: stable@vger.kernel.org # v3.7+
Signed-off-by: Rob Herring <robh@kernel.org>
Andre Przywara [Fri, 13 Dec 2013 20:49:19 +0000 (21:49 +0100)]
ARM/cpuidle: remove __init tag from Calxeda cpuidle probe function
Commit
60a66e370007e8535b7a561353b07b37deaf35ba changed the Calxeda
cpuidle driver to a platform driver, copying the __init tag from the
_init() to the newly used _probe() function. However, "probe should
not be __init." (Rob said ;-)
Remove the __init tag to fix a section mismatch in the Calxeda
cpuidle driver.
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Sebastian Ott [Wed, 18 Dec 2013 15:46:02 +0000 (16:46 +0100)]
s390/pci: obtain function handle in hotplug notifier
When using the CLP interface to enable or disable a pci device a
valid function handle needs to be delivered. So far our assumption
was that we always have an up-to-date version of the function handle
(since it doesn't change when the device is in use). This assumption
is incorrect if the pci device is enabled or disabled outside of our
control. When we are notified about such a change we already receive
the new function handle. Just use it.
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Benjamin Herrenschmidt [Mon, 30 Dec 2013 03:48:27 +0000 (14:48 +1100)]
Merge remote-tracking branch 'agust/merge' into merge
Anatolij writes:
Please pull two DTS fixes for MPC5125 tower board. Without
them the v3.13-rcX kernels do not boot.
Vince Bridgers [Fri, 20 Dec 2013 17:19:34 +0000 (11:19 -0600)]
stmmac: Fix incorrect spinlock release and PTP cap detection.
This patch corrects a problem in stmmac_ptp.c, functions
stmmac_adjust_time and stmmac_adjust_freq where the incorrect spinlocks
were released. This patch also addresses a problem in stmmac_main,
function stmmac_init_ptp where the capability detection for
advanced timestamping was masked by message masking.
This patch was touch tested using linuxptp, and runs without the previously
observed instabilities. More extensive testing is ongoing.
Vince
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Fri, 20 Dec 2013 19:09:04 +0000 (22:09 +0300)]
phy: IRQ cannot be shared
With the way PHY IRQ handler is implemented (all real handling being pushed to
the workqueue and returning IRQ_HANDLED all the time PHY is active), we cannot
really claim that PHY IRQ can be shared when calling request_irq().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Sun, 22 Dec 2013 23:32:31 +0000 (00:32 +0100)]
net: rose: restore old recvmsg behavior
recvmsg handler in net/rose/af_rose.c performs size-check ->msg_namelen.
After commit
f3d3342602f8bcbf37d7c46641cb9bca7618eb1c
(net: rework recvmsg handler msg_name and msg_namelen logic), we now
always take the else branch due to namelen being initialized to 0.
Digging in netdev-vger-cvs git repo shows that msg_namelen was
initialized with a fixed-size since at least 1995, so the else branch
was never taken.
Compile tested only.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Durrant [Mon, 23 Dec 2013 09:27:17 +0000 (09:27 +0000)]
xen-netback: fix guest-receive-side array sizes
The sizes chosen for the metadata and grant_copy_op arrays on the guest
receive size are wrong;
- The meta array is needlessly twice the ring size, when we only ever
consume a single array element per RX ring slot
- The grant_copy_op array is way too small. It's sized based on a bogus
assumption: that at most two copy ops will be used per ring slot. This
may have been true at some point in the past but it's clear from looking
at start_new_rx_buffer() that a new ring slot is only consumed if a frag
would overflow the current slot (plus some other conditions) so the actual
limit is MAX_SKB_FRAGS grant_copy_ops per ring slot.
This patch fixes those two sizing issues and, because grant_copy_ops grows
so much, it pulls it out into a separate chunk of vmalloc()ed memory.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fabio Estevam [Tue, 24 Dec 2013 14:16:01 +0000 (12:16 -0200)]
fec: Do not assume that PHY reset is active low
We should not assume that the PHY reset is always active low.
Retrieve this information from the device tree instead, so that the PHY reset
can work on both cases.
Reported-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ying Xue [Fri, 27 Dec 2013 02:18:28 +0000 (10:18 +0800)]
tipc: fix deadlock during socket release
A deadlock might occur if name table is withdrawn in socket release
routine, and while packets are still being received from bearer.
CPU0 CPU1
T0: recv_msg() release()
T1: tipc_recv_msg() tipc_withdraw()
T2: [grab node lock] [grab port lock]
T3: tipc_link_wakeup_ports() tipc_nametbl_withdraw()
T4: [grab port lock]* named_cluster_distribute()
T5: wakeupdispatch() tipc_link_send()
T6: [grab node lock]*
The opposite order of holding port lock and node lock on above two
different paths may result in a deadlock. If socket lock instead of
port lock is used to protect port instance in tipc_withdraw(), the
reverse order of holding port lock and node lock will be eliminated,
as a result, the deadlock is killed as well.
Reported-by: Lars Everbrand <lars.everbrand@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Olof Johansson [Sat, 28 Dec 2013 21:01:47 +0000 (13:01 -0800)]
powerpc: Fix alignment of secondary cpu spin vars
Commit
5c0484e25ec0 ('powerpc: Endian safe trampoline') resulted in
losing proper alignment of the spinlock variables used when booting
secondary CPUs, causing some quite odd issues with failing to boot on
PA Semi-based systems.
This showed itself on ppc64_defconfig, but not on pasemi_defconfig,
so it had gone unnoticed when I initially tested the LE patch set.
Fix is to add explicit alignment instead of relying on good luck. :)
[ It appears that there is a different issue with PA Semi systems
however this fix is definitely correct so applying anyway -- BenH
]
Fixes: 5c0484e25ec0 ('powerpc: Endian safe trampoline')
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=67811
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Mon, 23 Dec 2013 01:19:51 +0000 (12:19 +1100)]
powerpc: Align p_end
p_end is an 8 byte value embedded in the text section. This means it
is only 4 byte aligned when it should be 8 byte aligned. Fix this
by adding an explicit alignment.
This fixes an issue where POWER7 little endian builds with
CONFIG_RELOCATABLE=y fail to boot.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Brian W Hart [Fri, 20 Dec 2013 19:06:01 +0000 (13:06 -0600)]
powernv/eeh: Add buffer for P7IOC hub error data
Prevent ioda_eeh_hub_diag() from clobbering itself when called by supplying
a per-PHB buffer for P7IOC hub diagnostic data. Take care to inform OPAL of
the correct size for the buffer.
[Small style change to the use of sizeof -- BenH]
Signed-off-by: Brian W Hart <hartb@linux.vnet.ibm.com>
Acked-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Brian W Hart [Thu, 19 Dec 2013 23:14:07 +0000 (17:14 -0600)]
powernv/eeh: Fix possible buffer overrun in ioda_eeh_phb_diag()
PHB diagnostic buffer may be smaller than PAGE_SIZE, especially when
PAGE_SIZE > 4KB.
Signed-off-by: Brian W Hart <hartb@linux.vnet.ibm.com>
Acked-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Paul E. McKenney [Tue, 17 Dec 2013 22:29:57 +0000 (09:29 +1100)]
powerpc: Make 64-bit non-VMX __copy_tofrom_user bi-endian
The powerpc 64-bit __copy_tofrom_user() function uses shifts to handle
unaligned invocations. However, these shifts were designed for
big-endian systems: On little-endian systems, they must shift in the
opposite direction.
This commit relies on the C preprocessor to insert the correct shifts
into the assembly code.
[ This is a rare but nasty LE issue. Most of the time we use the POWER7
optimised __copy_tofrom_user_power7 loop, but when it hits an exception
we fall back to the base __copy_tofrom_user loop. - Anton ]
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Rajesh B Prathipati [Mon, 16 Dec 2013 07:58:22 +0000 (18:58 +1100)]
powerpc: Make unaligned accesses endian-safe for powerpc
The generic put_unaligned/get_unaligned macros were made endian-safe by
calling the appropriate endian dependent macros based on the endian type
of the powerpc processor.
Signed-off-by: Rajesh B Prathipati <rprathip@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Mon, 16 Dec 2013 04:12:43 +0000 (15:12 +1100)]
powerpc: Fix bad stack check in exception entry
In EXCEPTION_PROLOG_COMMON() we check to see if the stack pointer (r1)
is valid when coming from the kernel. If it's not valid, we die but
with a nice oops message.
Currently we allocate a stack frame (subtract INT_FRAME_SIZE) before we
check to see if the stack pointer is negative. Unfortunately, this
won't detect a bad stack where r1 is less than INT_FRAME_SIZE.
This patch fixes the check to compare the modified r1 with
-INT_FRAME_SIZE. With this, bad kernel stack pointers (including NULL
pointers) are correctly detected again.
Kudos to Paulus for finding this.
Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Linus Torvalds [Mon, 30 Dec 2013 00:01:33 +0000 (16:01 -0800)]
Linux 3.13-rc6
Rafael J. Wysocki [Sun, 29 Dec 2013 22:37:15 +0000 (23:37 +0100)]
PCI / ACPI: Install wakeup notify handlers for all PCI devs with ACPI
It turns out that some BIOSes don't report wakeup GPEs through
_PRW, but use them for signaling wakeup anyway, which causes GPE
storms to occur on some systems after resume from system suspend.
This issue has been uncovered by commit
d2e5f0c16ad6 (ACPI / PCI:
Rework the setup and cleanup of device wakeup) during the 3.9
development cycle.
Work around the problem by installing wakeup notify handlers for all
PCI devices with ACPI support (i.e. having ACPI companions) regardless
of whether or not the BIOS reports ACPI wakeup support for them. The
presence of the wakeup notify handlers alone is not harmful in any
way if there are no events for them to handle (they are simply never
executed then), but on some systems they are needed to take care of
spurious events.
Fixes: d2e5f0c16ad6 (ACPI / PCI: Rework the setup and cleanup of device wakeup)
References: https://bugzilla.kernel.org/show_bug.cgi?id=63021
Reported-and-tested-by: Agustin Barto <abarto@gmail.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Sun, 29 Dec 2013 21:49:51 +0000 (13:49 -0800)]
Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another smallish batch of fixes, it's been quiet due to the holidays.
Nothing controversial here, a handful of things across the board"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: pxa: fix USB gadget driver compilation regression
ARM: OMAP2+: Fix LCD panel backlight regression for LDP legacy booting
ARM: OMAP2+: hwmod_data: fix missing OMAP_INTC_START in irq data
ARM: DRA7: hwmod: Fix boot crash with DEBUG_LL
ARM: shmobile: r8a7790: fix shdi resource sizes
ARM: shmobile: bockw: fixup DMA mask
ARM: shmobile: armadillo: Add PWM backlight power supply
Linus Torvalds [Sun, 29 Dec 2013 21:35:04 +0000 (13:35 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"There is a small EFI fix and a big power regression fix in this batch.
My queue also had a fix for downing a CPU when there are insufficient
number of IRQ vectors available, but I'm holding that one for now due
to recent bug reports"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/efi: Don't select EFI from certain special ACPI drivers
x86 idle: Repair large-server 50-watt idle-power regression
Linus Torvalds [Sun, 29 Dec 2013 21:27:51 +0000 (13:27 -0800)]
Merge tag 'pm+acpi-3.13-rc6' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes and new device IDs from Rafael Wysocki:
- Fix for a cpufreq regression causing stale sysfs files to be left
behind during system resume if cpufreq_add_dev() fails for one or
more CPUs from Viresh Kumar.
- Fix for a bug in cpufreq causing CONFIG_CPU_FREQ_DEFAULT_* to be
ignored when the intel_pstate driver is used from Jason Baron.
- System suspend fix for a memory leak in pm_vt_switch_unregister()
that forgot to release objects after removing them from
pm_vt_switch_list. From Masami Ichikawa.
- Intel Valley View device ID and energy unit encoding update for the
(recently added) Intel RAPL (Running Average Power Limit) driver from
Jacob Pan.
- Intel Bay Trail SoC GPIO and ACPI device IDs for the Low Power
Subsystem (LPSS) ACPI driver from Paul Drews.
* tag 'pm+acpi-3.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
powercap / RAPL: add support for ValleyView Soc
PM / sleep: Fix memory leak in pm_vt_switch_unregister().
cpufreq: Use CONFIG_CPU_FREQ_DEFAULT_* to set initial policy for setpolicy drivers
cpufreq: remove sysfs files for CPUs which failed to come back after resume
ACPI: Add BayTrail SoC GPIO and LPSS ACPI IDs
Viresh Kumar [Tue, 24 Dec 2013 01:41:01 +0000 (07:11 +0530)]
cpufreq: preserve user_policy across suspend/resume
Prevent __cpufreq_add_dev() from overwriting the existing values of
user_policy.{min|max|policy|governor} with defaults during resume
from system suspend.
Fixes: 5302c3fb2e62 ("cpufreq: Perform light-weight init/teardown during suspend/resume")
Reported-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rafael J. Wysocki [Fri, 27 Dec 2013 00:07:11 +0000 (01:07 +0100)]
cpufreq: Clean up after a failing light-weight initialization
If cpufreq_policy_restore() returns NULL during system resume,
__cpufreq_add_dev() should just fall back to the full initialization
instead of returning an error, because that may actually make things
work. Moreover, it should not leave stale fallback data behind after
it has failed to restore a previously existing policy.
This change is based on Viresh Kumar's work.
Fixes: 5302c3fb2e62 ("cpufreq: Perform light-weight init/teardown during suspend/resume")
Reported-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
David S. Miller [Sun, 29 Dec 2013 05:30:59 +0000 (00:30 -0500)]
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Included changes:
- reset netfilter-bridge state when removing the batman-adv
header from an incoming packet. This prevents netfilter
bridge from being fooled when the same packet enters a
bridge twice (or more): the first time within the
batman-adv header and the second time without.
- adjust the packet layout to prevent any architecture from
adding padding bytes. All the structs sent over the wire
now have size multiple of 4bytes (unless pack(2) is used).
- fix access to the inner vlan_eth header when reading the
VID in the rx path.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 29 Dec 2013 05:24:28 +0000 (00:24 -0500)]
Merge branch 'master' of git://git./linux/kernel/git/pablo/nf
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
This patchset contains four nf_tables fixes, one IPVS fix due to
missing updates in the interaction with the new sedadj conntrack
extension that was added to support the netfilter synproxy code,
and a couple of one-liners to fix netnamespace netfilter issues.
More specifically, they are:
* Fix ipv6_find_hdr() call without offset being explicitly initialized
in nft_exthdr, as required by that function, from Daniel Borkmann.
* Fix oops in nfnetlink_log when using netns and unloading the kernel
module, from Gao feng.
* Fix BUG_ON in nf_ct_timestamp extension after netns is destroyed,
from Helmut Schaa.
* Fix crash in IPVS due to missing sequence adjustment extension being
allocated in the conntrack, from Jesper Dangaard Brouer.
* Add bugtrap to spot a warning in case you deference sequence adjustment
conntrack area when not available, this should help to catch similar
invalid dereferences in the Netfilter tree, also from Jesper.
* Fix incomplete dumping of sets in nf_tables when retrieving by family,
from me.
* Fix oops when updating the table state (dormant <-> active) and having
user (not base ) chains, from me.
* Fix wrong validation in set element data that results in returning
-EINVAL when using the nf_tables dictionary feature with mappings,
also from me.
We don't usually have this amount of fixes by this time (as we're already
in -rc5 of the development cycle), although half of them are related to
nf_tables which is a relatively new thing, and I also believe that holidays
have also delayed the flight of bugfixes to mainstream a bit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Olof Johansson [Sat, 28 Dec 2013 23:38:32 +0000 (15:38 -0800)]
Merge tag 'omap-for-v3.13/intc-ldp-fix' of git://git./linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Fix a regression for wrong interrupt numbers for some devices after
the sparse IRQ conversion, fix DRA7 console output for earlyprintk,
and fix the LDP LCD backlight when DSS is built into the kernel and
not as a loadable module.
* tag 'omap-for-v3.13/intc-ldp-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix LCD panel backlight regression for LDP legacy booting
ARM: OMAP2+: hwmod_data: fix missing OMAP_INTC_START in irq data
ARM: DRA7: hwmod: Fix boot crash with DEBUG_LL
+ v3.13-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 28 Dec 2013 23:20:35 +0000 (15:20 -0800)]
Merge tag 'renesas-fixes2-for-v3.13' of git://git./linux/kernel/git/horms/renesas into fixes
From Simon Horman:
Second Round of Renesas ARM based SoC Fixes for v3.13
* r8a7790 (R-Car H2) based Lager board
- Correct SHDI resource sizes
This bug has been present since sdhi resources were added to the r8a7790 by
8c9b1aa41853272a ("ARM: shmobile: r8a7790: add MMCIF and SDHI DT
templates") in v3.11-rc2.
* r8a7778 (R-Car M1) based Bock-W board
- Correct DMA mask
This resolves a regression introduced by
4dcfa60071b3d23f
("ARM: DMA-API: better handing of DMA masks for coherent allocations")
in v3.12-rc1.
* r8a7740 (R-Mobile A1) based Armadillo board
- Add PWM backlight power supply
This resolves a regression introduced by
22ceeee16eb8f0d0
("pwm-backlight: Add power supply support") in v3.12.
* tag 'renesas-fixes2-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790: fix shdi resource sizes
ARM: shmobile: bockw: fixup DMA mask
ARM: shmobile: armadillo: Add PWM backlight power supply
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Walleij [Wed, 11 Dec 2013 08:48:58 +0000 (09:48 +0100)]
ARM: pxa: fix USB gadget driver compilation regression
After commit
88f718e3fa4d67f3a8dbe79a2f97d722323e4051
"ARM: pxa: delete the custom GPIO header" a compilation
error was introduced in the PXA25x gadget driver.
An attempt to fix the problem was made in
commit
b144e4ab1ef130e8bf30bcd3e529b7f35112c503
"usb: gadget: fix pxa25x compilation problems"
by explictly stating the driver needs the <mach/hardware.h>
header, which solved the compilation for a few boards,
such as the pxa255-idp and its defconfig.
However the Lubbock board has this special clause in
drivers/usb/gadget/pxa25x_udc.c:
This include file has an implicit dependency on
<mach/irqs.h> having been included before <mach/lubbock.h>
was included.
Before commit
88f718e3fa4d67f3a8dbe79a2f97d722323e4051
"ARM: pxa: delete the custom GPIO header" this implicit
dependency for the pxa25x_udc compile on the Lubbock was
satisfied by <linux/gpio.h> implicitly including
<mach/gpio.h> which was in turn including <mach/irqs.h>,
apart from the earlier added <mach/hardware.h>.
Fix this by having the PXA25x <mach/lubbock.h> explicitly
include <mach/irqs.h>.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Greg Kroah-Hartmann <gregkh@linuxfoundation.org>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pablo Neira Ayuso [Fri, 27 Dec 2013 23:59:38 +0000 (00:59 +0100)]
netfilter: nf_tables: fix wrong datatype in nft_validate_data_load()
This patch fixes dictionary mappings, eg.
add rule ip filter input meta dnat set tcp dport map { 22 => 1.1.1.1, 23 => 2.2.2.2 }
The kernel was returning -EINVAL in nft_validate_data_load() since
the type of the set element data that is passed was the real userspace
datatype instead of NFT_DATA_VALUE.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Antonio Quartulli [Mon, 23 Dec 2013 20:43:39 +0000 (21:43 +0100)]
batman-adv: fix vlan header access
When batadv_get_vid() is invoked in interface_rx() the
batman-adv header has already been removed, therefore
the header_len argument has to be 0.
Introduced by
c018ad3de61a1dc4194879a53e5559e094aa7b1a
("batman-adv: add the VLAN ID attribute to the TT entry")
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Antonio Quartulli [Mon, 23 Dec 2013 00:28:05 +0000 (01:28 +0100)]
batman-adv: clean nf state when removing protocol header
If an interface enslaved into batman-adv is a bridge (or a
virtual interface built on top of a bridge) the nf_bridge
member of the skbs reaching the soft-interface is filled
with the state about "netfilter bridge" operations.
Then, if one of such skbs is locally delivered, the nf_bridge
member should be cleaned up to avoid that the old state
could mess up with other "netfilter bridge" operations when
entering a second bridge.
This is needed because batman-adv is an encapsulation
protocol.
However at the moment skb->nf_bridge is not released at all
leading to bogus "netfilter bridge" behaviours.
Fix this by cleaning the netfilter state of the skb before
it gets delivered to the upper layer in interface_rx().
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Antonio Quartulli [Sun, 15 Dec 2013 12:26:55 +0000 (13:26 +0100)]
batman-adv: fix alignment for batadv_tvlv_tt_change
Make struct batadv_tvlv_tt_change a multiple 4 bytes long
to avoid padding on any architecture.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Simon Wunderlich [Mon, 2 Dec 2013 19:38:33 +0000 (20:38 +0100)]
batman-adv: fix size of batadv_bla_claim_dst
Since this is a mac address and always 48 bit, and we can assume that
it is always aligned to 2-byte boundaries, add a pack(2) pragma.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Antonio Quartulli [Thu, 5 Dec 2013 14:33:00 +0000 (15:33 +0100)]
batman-adv: fix size of batadv_icmp_header
struct batadv_icmp_header currently has a size of 17, which
will be padded to 20 on some architectures. Fix this by
unrolling the header into the parent structures.
Moreover keep the ICMP parsing functions as generic as they
are now by using a stub icmp_header struct during packet
parsing.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Simon Wunderlich [Mon, 2 Dec 2013 19:38:31 +0000 (20:38 +0100)]
batman-adv: fix header alignment by unrolling batadv_header
The size of the batadv_header of 3 is problematic on some architectures
which automatically pad all structures to a 32 bit boundary. To not lose
performance by packing this struct, better embed it into the various
host structures.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Simon Wunderlich [Mon, 2 Dec 2013 19:38:30 +0000 (20:38 +0100)]
batman-adv: fix alignment for batadv_coded_packet
The compiler may decide to pad the structure, and then it does not
have the expected size of 46 byte. Fix this by moving it in the
pragma pack(2) part of the code.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Pablo Neira Ayuso [Fri, 27 Dec 2013 09:44:23 +0000 (10:44 +0100)]
netfilter: nf_tables: fix oops when updating table with user chains
This patch fixes a crash while trying to deactivate a table that
contains user chains. You can reproduce it via:
% nft add table table1
% nft add chain table1 chain1
% nft-table-upd ip table1 dormant
[ 253.021026] BUG: unable to handle kernel NULL pointer dereference at
0000000000000030
[ 253.021114] IP: [<
ffffffff8134cebd>] nf_register_hook+0x35/0x6f
[ 253.021167] PGD
30fa5067 PUD
30fa2067 PMD 0
[ 253.021208] Oops: 0000 [#1] SMP
[...]
[ 253.023305] Call Trace:
[ 253.023331] [<
ffffffffa0885020>] nf_tables_newtable+0x11c/0x258 [nf_tables]
[ 253.023385] [<
ffffffffa0878592>] nfnetlink_rcv_msg+0x1f4/0x226 [nfnetlink]
[ 253.023438] [<
ffffffffa0878418>] ? nfnetlink_rcv_msg+0x7a/0x226 [nfnetlink]
[ 253.023491] [<
ffffffffa087839e>] ? nfnetlink_bind+0x45/0x45 [nfnetlink]
[ 253.023542] [<
ffffffff8134b47e>] netlink_rcv_skb+0x3c/0x88
[ 253.023586] [<
ffffffffa0878973>] nfnetlink_rcv+0x3af/0x3e4 [nfnetlink]
[ 253.023638] [<
ffffffff813fb0d4>] ? _raw_read_unlock+0x22/0x34
[ 253.023683] [<
ffffffff8134af17>] netlink_unicast+0xe2/0x161
[ 253.023727] [<
ffffffff8134b29a>] netlink_sendmsg+0x304/0x332
[ 253.023773] [<
ffffffff8130d250>] __sock_sendmsg_nosec+0x25/0x27
[ 253.023820] [<
ffffffff8130fb93>] sock_sendmsg+0x5a/0x7b
[ 253.023861] [<
ffffffff8130d5d5>] ? copy_from_user+0x2a/0x2c
[ 253.023905] [<
ffffffff8131066f>] ? move_addr_to_kernel+0x35/0x60
[ 253.023952] [<
ffffffff813107b3>] SYSC_sendto+0x119/0x15c
[ 253.023995] [<
ffffffff81401107>] ? sysret_check+0x1b/0x56
[ 253.024039] [<
ffffffff8108dc30>] ? trace_hardirqs_on_caller+0x140/0x1db
[ 253.024090] [<
ffffffff8120164e>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[ 253.024141] [<
ffffffff81310caf>] SyS_sendto+0x9/0xb
[ 253.026219] [<
ffffffff814010e2>] system_call_fastpath+0x16/0x1b
Reported-by: Alex Wei <alex.kern.mentor@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso [Tue, 24 Dec 2013 17:32:35 +0000 (18:32 +0100)]
netfilter: nf_tables: fix dumping with large number of sets
If not table name is specified, the dumping of the existing sets
may be incomplete with a sufficiently large number of sets and
tables. This patch fixes missing reset of the cursors after
finding the location of the last object that has been included
in the previous multi-part message.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Shirish Pargaonkar [Wed, 11 Dec 2013 22:29:53 +0000 (16:29 -0600)]
cifs: set FILE_CREATED
Set FILE_CREATED on O_CREAT|O_EXCL.
cifs code didn't change during commit
116cc0225381415b96551f725455d067f63a76a0
Kernel bugzilla 66251
Signed-off-by: Shirish Pargaonkar <spargaonkar@suse.com>
Acked-by: Jeff Layton <jlayton@redhat.com>
CC: Stable <stable@kernel.org>
Signed-off-by: Steve French <smfrench@gmail.com>
Sachin Prabhu [Mon, 25 Nov 2013 17:09:48 +0000 (17:09 +0000)]
cifs: We do not drop reference to tlink in CIFSCheckMFSymlink()
When we obtain tcon from cifs_sb, we use cifs_sb_tlink() to first obtain
tlink which also grabs a reference to it. We do not drop this reference
to tlink once we are done with the call.
The patch fixes this issue by instead passing tcon as a parameter and
avoids having to obtain a reference to the tlink. A lookup for the tcon
is already made in the calling functions and this way we avoid having to
re-run the lookup. This is also consistent with the argument list for
other similar calls for M-F symlinks.
We should also return an ENOSYS when we do not find a protocol specific
function to lookup the MF Symlink data.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
CC: Stable <stable@kernel.org>
Signed-off-by: Steve French <smfrench@gmail.com>
Steve French [Mon, 9 Dec 2013 15:18:09 +0000 (09:18 -0600)]
Add missing end of line termination to some cifs messages
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Gregor Beck <gbeck@sernet.de>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Li RongQing [Fri, 20 Dec 2013 09:20:12 +0000 (17:20 +0800)]
ipv6: release dst properly in ipip6_tunnel_xmit
if a dst is not attached to anywhere, it should be released before
exit ipip6_tunnel_xmit, otherwise cause dst memory leakage.
Fixes: 61c1db7fae21 ("ipv6: sit: add GSO/TSO support")
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Gibson [Fri, 20 Dec 2013 04:10:44 +0000 (15:10 +1100)]
netxen: Correct off-by-one errors in bounds checks
netxen_process_lro() contains two bounds checks. One for the ring number
against the number of rings, and one for the Rx buffer ID against the
array of receive buffers.
Both of these have off-by-one errors, using > instead of >=. The correct
versions are used in netxen_process_rcv(), they're just wrong in
netxen_process_lro().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 27 Dec 2013 18:04:33 +0000 (13:04 -0500)]
net: Add some clarification to skb_tx_timestamp() comment.
We've seen so many instances of people invoking skb_tx_timestamp()
after the device already has been given the packet, that it's worth
being a little bit more verbose and explicit in this comment.
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 20 Dec 2013 02:10:40 +0000 (18:10 -0800)]
arc_emac: fix potential use after free
Signed-off-by: Eric Dumazet <edumazet@google.com>
skb_tx_timestamp(skb) should be called _before_ TX completion
has a chance to trigger, otherwise it is too late and we access
freed memory.
Fixes: e4f2379db6c6 ("ethernet/arc/arc_emac - Add new driver")
From: Eric Dumazet <edumazet@google.com>
Cc: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nithin Sujir [Fri, 20 Dec 2013 01:44:11 +0000 (17:44 -0800)]
tg3: Expand 4g_overflow_test workaround to skb fragments of any size.
The current driver assumes that an skb fragment can only be upto jumbo
size. Presumably this was a fast-path optimization. This assumption is
no longer true as fragments can be upto 32k.
v2: Remove unnecessary parantheses per Eric Dumazet.
Cc: stable@vger.kernel.org
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Lindgren [Fri, 27 Dec 2013 17:51:25 +0000 (09:51 -0800)]
Merge tag 'for-v3.13-rc/hwmod-fixes-b' of git://git./linux/kernel/git/pjw/omap-pending into debug-ll-and-ldp-backlight-fix
A few OMAP hwmod fixes for v3.13-rc. One patch fixes some IRQ
problems with GPMC, RNG, and ISP/IVA MMUs on OMAP2/3. The other fixes
some problems with DEBUG_LL on DRA7xx.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/hwmod_fixes_b_v3.13-rc/
20131226021920/
Jamal Hadi Salim [Mon, 23 Dec 2013 13:02:11 +0000 (08:02 -0500)]
net_sched: act: Dont increment refcnt on replace
This is a bug fix. The existing code tries to kill many
birds with one stone: Handling binding of actions to
filters, new actions and replacing of action
attributes. A simple test case to illustrate:
XXXX
moja@fe1:~$ sudo tc actions add action drop index 12
moja@fe1:~$ actions get action gact index 12
action order 1: gact action drop
random type none pass val 0
index 12 ref 1 bind 0
moja@fe1:~$ sudo tc actions replace action ok index 12
moja@fe1:~$ actions get action gact index 12
action order 1: gact action drop
random type none pass val 0
index 12 ref 2 bind 0
XXXX
The above shows the refcounf being wrongly incremented on replace.
There are more complex scenarios with binding of actions to filters
that i am leaving out that didnt work as well...
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sasha Levin [Thu, 19 Dec 2013 04:49:42 +0000 (23:49 -0500)]
rds: prevent dereference of a NULL device
Binding might result in a NULL device, which is dereferenced
causing this BUG:
[ 1317.260548] BUG: unable to handle kernel NULL pointer dereference at
000000000000097
4
[ 1317.261847] IP: [<
ffffffff84225f52>] rds_ib_laddr_check+0x82/0x110
[ 1317.263315] PGD
418bcb067 PUD
3ceb21067 PMD 0
[ 1317.263502] Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
[ 1317.264179] Dumping ftrace buffer:
[ 1317.264774] (ftrace buffer empty)
[ 1317.265220] Modules linked in:
[ 1317.265824] CPU: 4 PID: 836 Comm: trinity-child46 Tainted: G W 3.13.0-rc4-
next-20131218-sasha-00013-g2cebb9b-dirty #4159
[ 1317.267415] task:
ffff8803ddf33000 ti:
ffff8803cd31a000 task.ti:
ffff8803cd31a000
[ 1317.268399] RIP: 0010:[<
ffffffff84225f52>] [<
ffffffff84225f52>] rds_ib_laddr_check+
0x82/0x110
[ 1317.269670] RSP: 0000:
ffff8803cd31bdf8 EFLAGS:
00010246
[ 1317.270230] RAX:
0000000000000000 RBX:
ffff88020b0dd388 RCX:
0000000000000000
[ 1317.270230] RDX:
ffffffff8439822e RSI:
00000000000c000a RDI:
0000000000000286
[ 1317.270230] RBP:
ffff8803cd31be38 R08:
0000000000000000 R09:
0000000000000000
[ 1317.270230] R10:
0000000000000000 R11:
0000000000000001 R12:
0000000000000000
[ 1317.270230] R13:
0000000054086700 R14:
0000000000a25de0 R15:
0000000000000031
[ 1317.270230] FS:
00007ff40251d700(0000) GS:
ffff88022e200000(0000) knlGS:
000000000000
0000
[ 1317.270230] CS: 0010 DS: 0000 ES: 0000 CR0:
000000008005003b
[ 1317.270230] CR2:
0000000000000974 CR3:
00000003cd478000 CR4:
00000000000006e0
[ 1317.270230] DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
[ 1317.270230] DR3:
0000000000000000 DR6:
00000000ffff0ff0 DR7:
0000000000090602
[ 1317.270230] Stack:
[ 1317.270230]
0000000054086700 5408670000a25de0 5408670000000002 0000000000000000
[ 1317.270230]
ffffffff84223542 00000000ea54c767 0000000000000000 ffffffff86d26160
[ 1317.270230]
ffff8803cd31be68 ffffffff84223556 ffff8803cd31beb8 ffff8800c6765280
[ 1317.270230] Call Trace:
[ 1317.270230] [<
ffffffff84223542>] ? rds_trans_get_preferred+0x42/0xa0
[ 1317.270230] [<
ffffffff84223556>] rds_trans_get_preferred+0x56/0xa0
[ 1317.270230] [<
ffffffff8421c9c3>] rds_bind+0x73/0xf0
[ 1317.270230] [<
ffffffff83e4ce62>] SYSC_bind+0x92/0xf0
[ 1317.270230] [<
ffffffff812493f8>] ? context_tracking_user_exit+0xb8/0x1d0
[ 1317.270230] [<
ffffffff8119313d>] ? trace_hardirqs_on+0xd/0x10
[ 1317.270230] [<
ffffffff8107a852>] ? syscall_trace_enter+0x32/0x290
[ 1317.270230] [<
ffffffff83e4cece>] SyS_bind+0xe/0x10
[ 1317.270230] [<
ffffffff843a6ad0>] tracesys+0xdd/0xe2
[ 1317.270230] Code: 00 8b 45 cc 48 8d 75 d0 48 c7 45 d8 00 00 00 00 66 c7 45 d0 02 00
89 45 d4 48 89 df e8 78 49 76 ff 41 89 c4 85 c0 75 0c 48 8b 03 <80> b8 74 09 00 00 01 7
4 06 41 bc 9d ff ff ff f6 05 2a b6 c2 02
[ 1317.270230] RIP [<
ffffffff84225f52>] rds_ib_laddr_check+0x82/0x110
[ 1317.270230] RSP <
ffff8803cd31bdf8>
[ 1317.270230] CR2:
0000000000000974
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Lindgren [Fri, 27 Dec 2013 17:33:27 +0000 (09:33 -0800)]
ARM: OMAP2+: Fix LCD panel backlight regression for LDP legacy booting
Looks like the LCD panel on LDP has been broken quite a while, and
recently got fixed by commit
0b2aa8bed3e1 (gpio: twl4030: Fix regression
for twl gpio output). However, there's still an issue left where the panel
backlight does not come on if the LCD drivers are built into the
kernel.
Fix the issue by registering the DPI LCD panel only after the twl4030
GPIO has probed.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[tony@atomide.com: updated per Tomi's comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Jesper Dangaard Brouer [Mon, 16 Dec 2013 16:09:47 +0000 (17:09 +0100)]
ipvs: correct usage/allocation of seqadj ext in ipvs
The IPVS FTP helper ip_vs_ftp could trigger an OOPS in nf_ct_seqadj_set,
after commit
41d73ec053d2 (netfilter: nf_conntrack: make sequence number
adjustments usuable without NAT).
This is because, the seqadj ext is now allocated dynamically, and the
IPVS code didn't handle this situation. Fix this in the IPVS nfct
code by invoking the alloc function nfct_seqadj_ext_add().
Fixes: 41d73ec053d2 (netfilter: nf_conntrack: make sequence number adjustments usuable without NAT)
Suggested-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Jesper Dangaard Brouer [Mon, 16 Dec 2013 16:09:41 +0000 (17:09 +0100)]
netfilter: WARN about wrong usage of sequence number adjustments
Since commit
41d73ec053d2 (netfilter: nf_conntrack: make sequence
number adjustments usuable without NAT), the sequence number extension
is dynamically allocated.
Instead of dying, give a WARN splash, in case of wrong usage of the
seqadj code, e.g. when forgetting to allocate via nfct_seqadj_ext_add().
Wrong usage have been seen in the IPVS code path.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Rafael J. Wysocki [Thu, 26 Dec 2013 23:43:24 +0000 (00:43 +0100)]
Merge branches 'powercap' and 'acpi-lpss' with new device IDs
* powercap:
powercap / RAPL: add support for ValleyView Soc
* acpi-lpss:
ACPI: Add BayTrail SoC GPIO and LPSS ACPI IDs
Rafael J. Wysocki [Thu, 26 Dec 2013 23:42:27 +0000 (00:42 +0100)]
Merge branches 'pm-cpufreq' and 'pm-sleep' containing PM fixes
* pm-cpufreq:
cpufreq: Use CONFIG_CPU_FREQ_DEFAULT_* to set initial policy for setpolicy drivers
cpufreq: remove sysfs files for CPUs which failed to come back after resume
* pm-sleep:
PM / sleep: Fix memory leak in pm_vt_switch_unregister().
projects / openwrt / staging / blogic.git / log