Sven Eckelmann [Wed, 9 Aug 2017 11:52:07 +0000 (13:52 +0200)]
ipq40xx: add support for OpenMesh A62
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ 802.3at POE+
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 18-24V passive POE (mode B)
* powered only via POE
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
The initramfs image can be started using
setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
set fdt_high 0x85000000
bootm 0x84000000
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Sven Eckelmann [Mon, 16 Apr 2018 11:51:15 +0000 (13:51 +0200)]
ipq40xx: fix gpio-hog related boot issues
The pinctrl initialization fails with the MSM pinctrl code and gpio-hogs
because either the gpio ranges are not yet initialized (missing gpio-range
in DT) or that the msm driver unconditionally tries to re-initializes the
ranges (gpio-range in DT).
To allow gpio-hogs and similar early-boot gpio code, the gpio-ranges must
be in the device tree and the pinctrl-msm code must check whether the range
was already initialized by the DT.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
[drop changes to unrelated dtsi files, refresh patches]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Sven Eckelmann [Thu, 19 Apr 2018 07:12:22 +0000 (09:12 +0200)]
ipq-wifi: drop custom board-2.bins
The BDFs for all boards were upstreamed to the ath10k-firmware
repository and are now part of ath10k-firmware 2018-04-19.
We switched to the upstream board-2.bin, hence the files can be removed
here.
Keep the ipq-wifi package in case new boards are added. It might take
some time till board-2.bins send upstream are merged.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Sven Eckelmann [Thu, 19 Apr 2018 07:12:22 +0000 (09:12 +0200)]
ipq40xx: use upstream board-2.bin
The BDFs for all boards were upstreamed to the ath10k-firmware
repository and are now part of ath10k-firmware 2018-04-19.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Sven Eckelmann [Thu, 19 Apr 2018 06:59:48 +0000 (08:59 +0200)]
firmware: ath10k-firmware: update to 2018-04-19
* introduces the BDFs in /lib/firmware/ath10k/QCA4019/hw1.0/board-2.bin
for:
- 8devices Jalapeno
- Asus RT-AC58U
- AVM FRITZ!Box 4040
- GL.iNet GL-B1300
- Meraki MR33
- Netgear EX6100v2
- Netgear EX6150v2
- OpenMesh A62
* introduces the BDFs in /lib/firmware/ath10k/QCA9888/hw2.0/board-2.bin
- OpenMesh A62
* adds new firmware for QCA6174 hw3.0
- firmware-6.bin_RM.4.4.1.c1-00038-QCARMSWP-1
- firmware-6.bin_RM.4.4.1.c1-00041-QCARMSWP-1
* various undocumented BDF updates to:
- QCA4019 hw1.0:
+ bus=ahb,bmi-chip-id=0,bmi-board-id=16
+ bus=ahb,bmi-chip-id=0,bmi-board-id=17
+ bus=ahb,bmi-chip-id=0,bmi-board-id=19
+ bus=ahb,bmi-chip-id=0,bmi-board-id=20
+ bus=ahb,bmi-chip-id=0,bmi-board-id=21
+ bus=ahb,bmi-chip-id=0,bmi-board-id=29
+ bus=ahb,bmi-chip-id=0,bmi-board-id=30
- QCA9888 hw2.0:
+ bus=pci,bmi-chip-id=0,bmi-board-id=16
+ bus=pci,bmi-chip-id=0,bmi-board-id=17
+ bus=pci,bmi-chip-id=0,bmi-board-id=18
+ bus=pci,bmi-chip-id=0,bmi-board-id=23
+ bus=pci,bmi-chip-id=0,bmi-board-id=24
+ bus=pci,bmi-chip-id=0,bmi-board-id=25
- QCA9984 hw1.0:
+ bus=pci,bmi-chip-id=0,bmi-board-id=1
+ bus=pci,bmi-chip-id=0,bmi-board-id=3
+ bus=pci,bmi-chip-id=0,bmi-board-id=5
+ bus=pci,bmi-chip-id=0,bmi-board-id=6
+ bus=pci,bmi-chip-id=0,bmi-board-id=7
+ bus=pci,bmi-chip-id=0,bmi-board-id=8
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Hans Dedecker [Mon, 23 Apr 2018 19:39:16 +0000 (21:39 +0200)]
odhcpd: update to latest git HEAD
4136529 dhcpv6-ia: keep tentative assignments alive for a short time
200cc8f dhcpv6-ia: make assignment lookup more strict
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Rafał Miłecki [Mon, 23 Apr 2018 11:33:09 +0000 (13:33 +0200)]
brcm47xx: backport upstream patches for Netgear WNR1000 V3
This includes fix for reading NVRAM content.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Thomas Hebb [Fri, 12 Jan 2018 20:59:25 +0000 (15:59 -0500)]
mac80211: update patch to read ath10k variant from DT
This patch was revised upstream before being merged, and OpenWrt's copy
was never updated to reflect the revision.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
[refreshed patches]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Thomas Hebb [Thu, 19 Apr 2018 18:34:56 +0000 (14:34 -0400)]
ipq40xx: ex61x0v2: Disable unused GMACs
These devices have only one ethernet port. It doesn't make sense to
expose the unused GMACs as separate network devices.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Sven Eckelmann [Wed, 18 Apr 2018 07:48:51 +0000 (09:48 +0200)]
ipq40xx: Move reserved-memory DT to qcom-ipq4019.dtsi
The tz and smem reserved-memory information handled in the upstream Linux
sources by the SoC specific dtsi and not by the the boards dts. Using the
same approach in OpenWrt avoids unneccessary duplication.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Sven Eckelmann [Tue, 17 Apr 2018 12:31:53 +0000 (14:31 +0200)]
ipq40xx: Remove unused reserved-memory nodes
The reserved-memory regions are mostly undocumented by QCA and are named
very unspecific in the QSDK device trees. It was tried to clean them up by
commit
71ed9f10a33e ("ipq40xx: Use detailed reserved memory for A42") and
similar changes.
The features which require these regions were mostly unknown but
Senthilkumar N L <snlakshm@qti.qualcomm.com> and Sricharan Ramabadhran
<srichara@qti.qualcomm.com> provided some more insight in some of them:
* crash dump feature
- a couple of regions used when 'qca,scm_restart_reason' dt node has the
value 'dload_status' not set to 1
+ apps_bl <0x87000000 0x400000>
+ sbl <0x87400000 0x100000>
+ cnss_debug <0x87400000 0x100000>
+ cpu_context_dump <0x87b00000 0x080000>
- required driver not available in Linux
- safe to remove
* QSEE app execution
- region tz_apps <0x87b80000 0x280000>
- required driver not available in Linux
- safe to remove
* communication with TZ/QSEE
- region smem <0x87b80000 0x280000>
- driver changes not yet upstreamed
- must not be removed because any access can crash kernel/program
* trustzone (QSEE) private memory
- region tz <0x87e80000 0x180000>
- must not be removed because any access can crash kernel/program
Removing the unnecessary regions saves some kilobyte of reserved-memory and
cleans up the device tree:
* 2560 KiB
- 8devices Jalapeno
- AVM FRITZ!Box 4040
- Compex WPJ428
- Meraki MR33 Access Point
- OpenMesh A42
* 14336 KiB
- GL.iNet GL-B1300
- Qualcomm Technologies, Inc. IPQ40xx/AP-DK01.1-C1
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Mathias Kresin [Fri, 20 Apr 2018 04:30:46 +0000 (06:30 +0200)]
build: consolidate fake uImage header build commands
Merge the two existing functions and use a parameter for the type
header field.
It updates the syntax of the former mpc85xx fake ramdisk header
command to be compatible with mkimage from u-boot 2018.03 and fixes the
build error spotted by the build bot.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Kevin Darbyshire-Bryant [Fri, 20 Apr 2018 10:14:29 +0000 (10:14 +0000)]
wireguard: bump to
20180420
7cc2668 version: bump snapshot
860c7c7 poly1305: do not place constants in different sections
5f1e4ca compat: remove unused dev_recursion_level backport
7e4b991 blake2s: remove unused helper
13225fc send: simplify skb_padding with nice macro
a1525bf send: account for route-based MTU
bbb2fde wg-quick: account for specified fwmark in auto routing mode
c452105 qemu: bump default version
dbe5223 version: bump snapshot
1d3ef31 chacha20poly1305: put magic constant behind macro
cdc164c chacha20poly1305: add self tests from wycheproof
1060e54 curve25519: add self tests from wycheproof
0e1e127 wg-quick.8: fix typo
2b06b8e curve25519: precomp const correctness
8102664 curve25519: memzero in batches
1f54c43 curve25519: use cmov instead of xor for cswap
fa5326f curve25519: use precomp implementation instead of sandy2x
9b19328 compat: support OpenSUSE 15
3102d28 compat: silence warning on frankenkernels
8f64c61 compat: stable kernels are now receiving
b87b619
62127f9 wg-quick: hide errors on save
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Daniel Golle [Fri, 20 Apr 2018 05:41:03 +0000 (07:41 +0200)]
hostapd: fix encrypted mesh channel settings
Import two patches from Peter Oh to allow setting channel
bandwidth in the way it already works for managed interfaces.
This fixes mesh interfaces on 802.11ac devices always coming up in
VHT80 mode.
Add a patch to allow HT40 also on 2.4GHz if noscan option is set, which
also skips secondary channel scan just like noscan works in AP mode.
This time also make sure to add all files to the patch before
committing it...
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Jo-Philipp Wich [Fri, 20 Apr 2018 12:01:32 +0000 (14:01 +0200)]
rpcd: update to latest HEAD
6994c87 uci: fix session delta isolation
f0f6f81 session: remove redundant key attribute to rpc_session_set()
3d400c7 session: support reclaiming pending apply session
eb09f3a session: ignore non-string username attribute upon restore
edd37f8 uci: add rpc_uci_replace_savedir() helper
2423162 uci: switch to proper save directory on apply/rollback
66a9bad uci: fix memory leak in rpc_uci_apply_timeout()
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Felix Fietkau [Fri, 20 Apr 2018 11:04:41 +0000 (13:04 +0200)]
build: pass HOSTCXX to host builds as CXX
Fixes cmake build on some systems that also have an older clang++
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Fri, 20 Apr 2018 08:35:51 +0000 (10:35 +0200)]
Revert "hostapd: fix encrypted mesh channel settings"
This reverts commit
7f52919a2f2894125b4dca611eb2d30181af7e0b, which is
currently breaking the builds and needs to be reworked
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Fri, 20 Apr 2018 08:02:28 +0000 (10:02 +0200)]
mtd: fix erase handling with partition offset on write
When a partition offset is given, it is used in an lseek call, which
affects write, but not erase. Add it to the offset for erase calls as
well
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 19 Apr 2018 14:26:39 +0000 (16:26 +0200)]
uboot-envtools: remove makefile duplication for supported targets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 19 Apr 2018 13:37:59 +0000 (15:37 +0200)]
mediatek: disable ubifs
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 19 Apr 2018 13:37:22 +0000 (15:37 +0200)]
mediatek: remove 4.9 kernel config
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Daniel Golle [Fri, 20 Apr 2018 05:41:03 +0000 (07:41 +0200)]
hostapd: fix encrypted mesh channel settings
Import two patches from Peter Oh to allow setting channel
bandwidth in the way it already works for managed interfaces.
This fixes mesh interfaces on 802.11ac devices always coming up in
VHT80 mode.
Add a patch to allow HT40 also on 2.4GHz if noscan option is set, which
also skips secondary channel scan just like noscan works in AP mode.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 20 Apr 2018 05:39:10 +0000 (07:39 +0200)]
mac80211: pass down noscan to wpa_supplicant
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 20 Apr 2018 05:36:36 +0000 (07:36 +0200)]
netifd: update to latest git HEAD
b3dca7b wireless: include noscan option in common wdev vars
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Mathias Kresin [Thu, 19 Apr 2018 17:09:11 +0000 (19:09 +0200)]
build: fix uImage fake header command
Use a syntax compatible with mkimage from u-boot 2018.03 to fix the
build errors spotted by the build bot.
The images are binary identical to the ones generated with mkimage from
u-boot 2014.10.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Hans Dedecker [Thu, 19 Apr 2018 13:30:37 +0000 (15:30 +0200)]
odhcpd: update to latest git HEAD (FS#1457)
dcfc06a router: fix managed address configuration setting
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Leon M. George [Wed, 10 Jan 2018 16:20:22 +0000 (17:20 +0100)]
mac80211: join 5GHz checks
Before this commit, devices supporting both 2.4GHz and 5GHz would be
configured for 2.4GHz by default - unless they have VHT capabilities.
With this commit, channel 36 is only set when the frequency is supported.
VHT isn't checked unless that is the case.
Signed-off-by: Leon M. George <leon@georgemail.eu>
Hyeonsik Song [Mon, 5 Mar 2018 07:57:45 +0000 (16:57 +0900)]
toolchain/glibc: unset LD_LIBRARY_PATH
Fix build error when use glibc
Signed-off-by: Hyeonsik Song <blogcin@naver.com>
Florian Eckert [Fri, 8 Sep 2017 11:11:07 +0000 (13:11 +0200)]
network/uqmi: pipe the output off qmi_wds_stop to /dev/null
Pipe uqmi output from qmi_wds_stop function into /dev/null.
This will supress the following output in proto teardown.
netifd: wwan (x): "No effect"
netifd: wwan (x): Command failed: Permission denied
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Felix Fietkau [Mon, 9 Apr 2018 07:56:38 +0000 (09:56 +0200)]
orion: remove linux 4.4 support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Mon, 9 Apr 2018 07:56:21 +0000 (09:56 +0200)]
omap: remove linux 4.4 support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Mon, 9 Apr 2018 07:49:44 +0000 (09:49 +0200)]
mvebu: drop linux 4.4 and 4.9 support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Jo-Philipp Wich [Thu, 19 Apr 2018 06:26:15 +0000 (08:26 +0200)]
tools: mkimage: provide dtc path during build
The new mkimage version requires a CONFIG_MKIMAGE_DTC_PATH variable to be
provided during build, in order to hardcode a path to a suitable DT
compiler executable.
Failure to do so will result in stray "sh: 1: -I: not found" errors when
invoking mkimage for FIT image generation.
Fix the issue by supplying "dtc" as CONFIG_MKIMAGE_DTC_PATH value during
build. As we intend our host utilities to be relocatable and since we're
already overriding PATH when invoking mkimage, an absolute path is not
required.
Fixes: b13e981d72 ("tools/mkimage: update to version 2018.03")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Paul Wassi [Sun, 1 Apr 2018 16:18:18 +0000 (18:18 +0200)]
package/utils/lua: cleanup source mirrors
Remove inactive mirrors from the sources list.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Hauke Mehrtens [Sat, 14 Apr 2018 21:00:12 +0000 (23:00 +0200)]
tools/mkimage: update to version 2018.03
This activates support for fit images and some other new mkimage
features. Some of the patches were applied upstream and could be
removed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Luis Araneda [Fri, 6 Apr 2018 14:23:34 +0000 (11:23 -0300)]
uboot-envtools: update to 2018.03
Several changes has been made:
+ AES support has been removed by
upstream commit
c6831c7 (2017-11-14)
[remove patch "200-fw_env_no_aes.patch"]
+ Support for UBI volumes has beed added by
upstream commit
34255b9 (2017-11-15)
[remove patch "300-support-env-in-ubivol-chardev.patch"]
+ A command line argument has beed added ("-c") to manually indicate
the location of the environment configuration file
Also, patch "400-u-boot-2015.10-stdint.patch" is no longer
necessary, and the config option to enable UBI support has
been removed.
Size comparisons:
fw_printenv size:
Target Before After
ar71xx 15,189 bytes 18,133 bytes (+2,944 bytes)
ipq40xx 20,873 bytes 20,987 bytes (+114 bytes)
mvebu 20,881 bytes 20,991 bytes (+110 bytes)
ramips 15,128 bytes 18,072 bytes (+2,944 bytes)
OPKG package size:
Target Before After
ar71xx 11,309 bytes 12,875 bytes (+1,566 bytes)
ipq40xx 11,772 bytes 13,299 bytes (+1,527 bytes)
mvebu 11,609 bytes 13,114 bytes (+1,505 bytes)
ramips 10,975 bytes 12,503 bytes (+1,528 bytes)
Compile tested: ipq40xx (musl, glibc, gcc5-musl), ar71xx, mvebu, ramips
Run tested: ipq40xx (ASUS RT-AC58U)
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Hauke Mehrtens [Sat, 14 Apr 2018 12:33:46 +0000 (14:33 +0200)]
ustream-ssl: px5g: Rebuild package
mbedtls changed in version 2.7.0 the soversion of the libmbedcrypto.so
library, all applications using this shared library have to be
recompiled to be able to load the new library.
Some binaries got rebuild to for the 2.7.0 release and are now using
libmbedcrypto.so.1, the older ones are still using libmbedcrypto.so.0.
Fixes: 75c5ab4ca ("mbedtls: update to version 2.7.0")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Kabuli Chana [Fri, 30 Mar 2018 16:35:47 +0000 (10:35 -0600)]
mwlwifi: update to version 10.3.4.0-2018-03-30
Upgrade 88W8964 firmware to 9.3.2.6
Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
Stefan Lippers-Hollmann [Tue, 10 Apr 2018 20:24:27 +0000 (22:24 +0200)]
mac80211: ipw2200-fw: fix download mirror(s)
bughost.org hasn't existed for 6-8 years, add a couple of current
mirrors to avoid the fallback to http://mirror2.openwrt.org/sources/.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Stefan Lippers-Hollmann [Tue, 10 Apr 2018 20:20:49 +0000 (22:20 +0200)]
mac80211: ipw2100-fw: fix download mirror(s)
bughost.org hasn't existed for 6-8 years, add a couple of current
mirrors to avoid the fallback to http://mirror2.openwrt.org/sources/.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Hauke Mehrtens [Sun, 15 Apr 2018 10:47:43 +0000 (12:47 +0200)]
ath10k-ct: make it depend on PCI support again
The missing dependency causes build problems on systems without PCI
support.
The ath10k_pci kernel module depends on PCI support so this dependency
should be added. ath10k now also supported the ahb interface on the
IPQ4019 SoC, but this SoC also has PCI support so this extra dependency
is not as problem.
Fixes: d0f3dd5b9f34176 ("ath10k-ct: update to latest version, enable AHB.")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Stefan Lippers-Hollmann [Tue, 27 Mar 2018 00:32:08 +0000 (02:32 +0200)]
mac80211: ath10k: Suppress "Unknown eventid: 36925" warnings
Merge upstream patch from Sathishkumar Muruganandam
<murugana@codeaurora.org> for OpenWrt's backports package:
https://lkml.kernel.org/r/<
1522049641-19521-1-git-send-email-murugana@codeaurora.org>
Commit-ID:
606204bb863fa3b0bb54929d79b4dc46338f9180
* FW has Smart Logging feature enabled by default for detecting failures
* and processing FATAL_CONDITION_EVENTID (36925 - 0x903D) back to host.
*
* Since ath10k doesn't implement the Smart Logging and FATAL CONDITION
* EVENT processing yet, suppressing the unknown event ID warning by moving
* this under ATH10K_DBG_WMI.
*
* Simulated the same issue by having associated STA powered off when
* ping flood was running from AP backbone. This triggerd STA KICKOUT
* in AP followed by FATAL CONDITION event 36925.
*
* Issue was reproduced and verified in below DUT
* ------------------------------------------------
* AP mode of OpenWRT QCA9984 running 6.0.8 with FW ver 10.4-3.5.3-00053
*
* Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Hauke Mehrtens [Wed, 18 Apr 2018 21:50:25 +0000 (23:50 +0200)]
mac80211: Fix loading of rsi_sdio module
When CONFIG_PM was not set rsi_sdio_reinit_device() was not compiled
into the driver but referenced.
This is a backport form the mainline Linux kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Evgeniy Didin [Wed, 4 Apr 2018 10:52:24 +0000 (13:52 +0300)]
mac80211: add RedPine RS9113 module support
RedPine RS9113 wireless module requires rsi91x driver to be built
and linux-firmware/rsi/rs9113_wlan_qspi.rps to be installed.
Also we add patch for successful compilation of rsi91x driver.
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: John Crispin <john@phrozen.org>
Daniel Golle [Wed, 18 Apr 2018 20:08:21 +0000 (22:08 +0200)]
hostapd: mesh: make forwarding configurable
For unencrypted mesh networks our scripts take care of setting
the various mesh_param values. wpa_supplicant changes somes of them
when being used for SAE encrypted mesh and previously didn't allow
configuring any of them. Add support for setting mesh_fwding (which
has to be set to 0 when using other routing protocols on top of
802.11s) and update our script to pass the value to wpa_supplicant.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Wed, 18 Apr 2018 15:52:51 +0000 (17:52 +0200)]
Revert "mac80211: pass hostapd control socket to mesh-mode supplicant"
This reverts commit
1356a66f94f31e636fafec514a1c658356ef51b3.
The change breaks wpa_supplicant.conf generation, more work is needed
to fix mesh+AP.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Felix Fietkau [Wed, 18 Apr 2018 10:19:30 +0000 (12:19 +0200)]
mt76: update to the latest version
ec8435e mt76: initialize rx lock earlier
e08d5da mt76x2: fix is_mt7612 routine
e2eedc9 mt7603: retry PSE reset calls
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 18 Apr 2018 09:21:01 +0000 (11:21 +0200)]
kernel: fix an issue with infinite stack traces on MIPS
Reproduced by enabling lockdep on MT7621
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Matthias Schiffer [Thu, 12 Apr 2018 20:14:56 +0000 (22:14 +0200)]
kernel: disable accept_ra by default
Our commands setting accept_ra to 0 on all interfaces got lost in the
transition to procd. This remained unnoticed for a long time, as we also
enable forwarding on all interfaces, which prevents RA handling by default.
Restore the commands, while also fixing a possible race condition in the
old version.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Felix Fietkau [Tue, 17 Apr 2018 13:02:27 +0000 (15:02 +0200)]
mt76: update to the latest version
ea6dd6f mt7603: add missing spin lock init
2d08440 mt76: add rcu locking around tx scheduling
8c92c91 mt7603: turn vif wcid entry back into a full mt7603_sta
ca5cc9a mt76: fix concurrent rx calls on A-MPDU release
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Tue, 17 Apr 2018 11:47:54 +0000 (13:47 +0200)]
mediatek: enable ramdisk support by default
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Tue, 17 Apr 2018 11:43:06 +0000 (13:43 +0200)]
mediatek: fix target FPU settings
This reverts commit
5555545494c876adedf4f0038db49c1d85527e78.
The target supports both NEON and VFPv4, but for this to work properly,
a few more changes are needed:
- enable NEON support in the kernel config
- add the fpu feature flag to the makefile
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Matthias Schiffer [Tue, 17 Apr 2018 09:30:59 +0000 (11:30 +0200)]
base-files: /lib/functions.sh: remove unused insert_modules
insert_modules has been unused since r5279.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Felix Fietkau [Sun, 15 Apr 2018 17:24:42 +0000 (19:24 +0200)]
ramips: fix locking issues in the ethernet driver
The stats update needs to protect against being interrupted by a tasklet
The u64 stats seqlock needs to be initialized
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Mathias Kresin [Tue, 17 Apr 2018 06:20:42 +0000 (08:20 +0200)]
ramips: mt7620: fix double use of pins
The pins are used as (LED) GPIOs and can't be used at the same time as
hardware controlled ephy (LED) pins.
Fixes: FS#1500
Signed-off-by: Mathias Kresin <dev@kresin.me>
Daniel Engberg [Sun, 15 Apr 2018 08:01:31 +0000 (10:01 +0200)]
curl: Deprecate idn(1) support and switch to xz tarball
libidn(1) is deprecated, add libidn2 support
Switch to xz tarball (smaller size)
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Rafał Miłecki [Mon, 16 Apr 2018 17:46:35 +0000 (19:46 +0200)]
fstools: update to latest master branch
e243683 libfstools: move mount points when switching to JFFS2
3782b59 libfstools: add "const" to char pointer arguments in mount_move()
79721f0 libfstools: fix foreachdir() to pass dir with a trailing slash
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Hans Dedecker [Mon, 16 Apr 2018 11:08:44 +0000 (13:08 +0200)]
netifd: update to latest git HEAD (coverity fixes)
513eb27 system-linux: check ioctl return value in system_vlan()
df1625d system-linux: check ioctl return value in system_if_flags()
209c508 system-linux: fix segfault on alloc failure in system_if_check()
4a8e20e system-linux: fix segfault on error in system_add_ip6_tunnel()
36e4700 handler: fix resource leak on error in netifd_init_script_handlers()
86a0e7c system-linux: remove unnecessary open call in system_if_dump_info()
1e2cf67 system-linux: fix memory leak on error in system_add_vxlan()
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Stijn Tintel [Sun, 15 Apr 2018 21:00:49 +0000 (00:00 +0300)]
kernel: bump 4.14 to 4.14.34
Refresh patches.
Update patches that no longer apply:
- backport/313-netfilter-remove-defensive-check-on-malformed-packet.patch
- pending/642-net-8021q-support-hardware-flow-table-offload.patch
Compile-tested: x86/64.
Runtime-tested: x86/64.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Stijn Tintel [Sun, 15 Apr 2018 18:41:11 +0000 (21:41 +0300)]
lldpd: bump to 1.0.1
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Hans Dedecker [Sun, 15 Apr 2018 18:10:56 +0000 (20:10 +0200)]
nghttp2: bump to 1.31.1
1e22b36c Update manual pages
0f818baf Bump up version number to 1.31.1
c411d169 Fix frame handling
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Felix Fietkau [Sun, 15 Apr 2018 08:21:53 +0000 (10:21 +0200)]
mt76: update to the latest version
1d23142 mt76: add led active low to debugfs
549f43b mt7603: ensure that the ACK flag is set for A-MPDUs with any acked subframe
df9f9f6 mt7603: always try tx rate1 first
9c52f36 mt7603: pull the final rate index from the status descriptor
f36f308 mt7603: improve validation of rx frames
9a23989 mt7603: remove warning on rx with invalid channel info
7a31731 mt76: check for pending reset before attempting to schedule tx
873a7c9 mt7603: call mt76_txq_schedule_all as a barrier to prevent tx during reset
d9e5da3 mt76: add rcu locking in tid reorder function
a8e8921 mt7603: add more checks to avoid dereferencing invalid pointers in wcid lookup
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Sat, 14 Apr 2018 17:52:36 +0000 (19:52 +0200)]
ramips: remove broken and bogus spinlock in the SPI driver
Based on patch by Neil Brown
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Sat, 14 Apr 2018 17:48:58 +0000 (19:48 +0200)]
ramips: add missing unlock in fe_phy_link_adjust
Based on patch by Neil Brown
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Matthias Schiffer [Fri, 13 Apr 2018 12:36:43 +0000 (14:36 +0200)]
base-files: remove /etc/sysctl.d/ from conffiles
Let's use /etc/sysctl.d for package-provided snippets and leave
/etc/sysctl.conf to the admin. Don't backup /etc/sysctl.d on upgrades, so
old defaults get replaced properly.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Felix Fietkau [Fri, 13 Apr 2018 11:13:20 +0000 (13:13 +0200)]
ramips: fix usb phy compatible string (should fix FS#1489)
In the new USB phy driver, it checks the compatible string before
attempting to iomap its mem resource and do the extra PHY init
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Matthias Schiffer [Thu, 12 Apr 2018 15:57:44 +0000 (17:57 +0200)]
base-files: move netfilter sysctl defaults to specific kmod packages
Avoid warnings when applying settings for uninstalled kmods. See also
FS#1073.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Matthias Schiffer [Thu, 12 Apr 2018 15:37:29 +0000 (17:37 +0200)]
base-files: move sysctl defaults to /etc/sysctl.d/10-default.conf
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Matthias Schiffer [Thu, 12 Apr 2018 15:33:51 +0000 (17:33 +0200)]
base-files: evaluate /etc/sysctl.d/* before /etc/sysctl.conf
We can use /etc/sysctl.d/* for package-supplied sysctl snippets, giving
admins the option to use /etc/sysctl.conf to override settings.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Matthias Schiffer [Thu, 12 Apr 2018 15:30:16 +0000 (17:30 +0200)]
base-files: remove /etc/uci-defaults/11_migrate-sysctl
11_migrate-sysctl has not been updated with new file hashes since 2012.
Let's get rid of it.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Christian Lamparter [Tue, 10 Apr 2018 15:59:42 +0000 (10:59 -0500)]
apm821xx: Force Ethernet PHYID on MX60/MX60W
The MX60's uboot disables all the PHYs before starting linux.
This causes the PHY/switch detection code to malfunction
almost all of the time. To get around this, set a compatible
flag to force PHYID.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Ben Greear [Thu, 12 Apr 2018 18:13:55 +0000 (11:13 -0700)]
ath10k-ct: Update firmware
This firmware has only small changes from the last commit, but
it does have an important fix for at least some PTK rekey logic.
The old firmware would have issues if the driver managed to set
a clear key while encryption was 'enabled'. This new firmware for
both wave-1 and wave-2 should not be susceptible to this type of
bug any more.
And remove mesh-bcast IE flag from wave-2, still need more work before
we can enable that flag in ath10k-ct firmware it seems.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Mathias Kresin [Thu, 12 Apr 2018 18:48:35 +0000 (20:48 +0200)]
ipq40xx: unbundle firmware and board file
Don't select the firmware with the board file, it prevents an easy use
of the -ct ath10k firmware. Select the firmware within the default
packages instead.
Remove the per device selection of the firmware now that it the
firmware is selected by default.
Signed-off-by: Mathias Kresin <dev@kresin.me>
David Bauer [Wed, 28 Mar 2018 22:32:38 +0000 (00:32 +0200)]
ipq40xx: add support for Netgear EX6100v2/EX6150v2
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MB Winbond W632GU6KB12J
FLASH: 16 MiB Macronix MX25L12805D
ETH: Qualcomm QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n/ac 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac
1x1 (EX6100)
2x2 (EX6150)
INPUT: Power, WPS, reset button
AP / Range-extender toggle
LED: Power, Router, Extender (dual), WPS, Left-/Right-arrow
SERIAL: Header next to QCA8072 chip.
VCC, TX, RX, GND (Square hole is VCC)
WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi (Correct MAC-address)
- 5 GHz WiFi (Correct MAC-address)
- Factory installation from WebIF
- Factory installation from tftp
- OpenWRT sysupgrade (Preserving and non-preserving)
- LEDs
- Buttons
Not Working:
- AP/Extender toggle-switch
Untested:
- Support on EX6100v2. They share the same GPL-Code and vendor-images.
The 6100v2 seems to lack one 5GHz stream and differs in the 5GHz
board-blob. I only own a EX6150v2, therefore i am only able to verify
functionality on this device.
Install via Web-Interface:
Upload the factory image to the device to the Netgear Web-Interface.
The device might asks you to confirm the update a second time due to
detecting the OpenWRT firmware as older. The device will automatically
reboot after the image is written to flash.
Install via TFTP:
Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command "fw_recovery" will start a tftp server, waiting for
a DNI image to be pushed.
Assign your computer the IP-address 192.168.1.10/24. Push image with
tftp -4 -v -m binary 192.168.1.1 -c put <OPENWRT_FACTORY>
Device will erase factory-partition first, then writes the pushed image
to flash and reboots.
Parts of this commit are based on Thomas Hebb's work on the
openwrt-devel mailinglist.
See https://lists.openwrt.org/pipermail/openwrt-devel/2018-January/043418.html
Signed-off-by: David Bauer <mail@david-bauer.net>
Robert Marko [Fri, 16 Mar 2018 17:09:19 +0000 (18:09 +0100)]
ipq-wifi: Add 8devices Jalapeno
Add custom board-2.bin for 8devices Jalapeno.
Upstreaming is in progress.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Robert Marko [Wed, 11 Apr 2018 09:14:36 +0000 (11:14 +0200)]
ipq40xx: add support for 8devices Jalapeno
This patch adds support for 8devices Jalapeno.
Specification:
QCA IPQ4018, Quad core ARM v7 Cortex A7 717MHz
256 MB of DDR3 RAM
8 MB of SPI NOR flash
128 MB of Winbond SPI NAND flash
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
requires special BDF in QCA4019/hw1.0/board-2.bin with:
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=8devices-Jalapeno
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
requires special BDF in QCA4019/hw1.0/board-2.bin with:
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=8devices-Jalapeno
ETH: Qualcomm Atheros QCA8072 Gigabit Switch (1 x LAN, 1 x WAN)
phy@mdio3:
Label: eth0
gmac0
phy@mdio4:
Label: eth1
gmac1
Installation instructions:
Since boards ship with old version of LEDE installation is simple.
Just use sysupgrade -n -F sysupgrade.bin
Syuspgrade needs to be forced since OpenWRT uses DT detection in recent
releases.
If you get error that FIT configuration is not found during boot it is
due to older U-boot used on your board.
That is because 8devices used custom FIT configuration partition name
as they internally had v1 and v2 boards.
Only v2 boards are sold so now they are shipping boards with never
U-boot using generic config@1 FIT partition name.
Also for old uboot it is possible to force loading config@1 by changing
uboot environment:
setenv boot5 'bootm 0x84000000#config@1’
saveenv
Signed-off-by: Robert Marko <robimarko@gmail.com>
Daniel Golle [Fri, 13 Apr 2018 04:00:03 +0000 (06:00 +0200)]
hostapd: fix compile of -mini variants
Fixes commit
d88934aa5a (hostapd: update to git snapshot of 2018-04-09)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 12 Apr 2018 23:37:06 +0000 (01:37 +0200)]
mac80211: pass hostapd control socket to mesh-mode supplicant
Unlike when operating in Ad-Hoc mode, we apparently need to pass the
hostapd control socket interface to wpa_supplicant when using 802.11s
mesh mode.
There also seems to still be something wrong with the logic setting
channel and (v)htmode parameters...
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 12 Apr 2018 11:07:22 +0000 (13:07 +0200)]
hostapd: update to git snapshot of 2018-04-09
And import patchset to allow 802.11s mesh on DFS channels, see also
http://lists.infradead.org/pipermail/hostap/2018-April/038418.html
Fix sae_password for encryption mesh (sent upstream as well).
Also refreshed existing patches and fixed 463-add-mcast_rate-to-11s.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hans Dedecker [Thu, 12 Apr 2018 11:57:57 +0000 (13:57 +0200)]
libubox: update to latest git HEAD
6eff829 utils: fix build error with g++
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Rafał Miłecki [Thu, 12 Apr 2018 06:25:17 +0000 (08:25 +0200)]
kernel: mtd: bcm47xxpart: improve handling TRX partition size
This is important fix for flash parsing in some corner cases. In case
of TRX subpartition with rootfs being aligned to the flash block size it
was incorrectly registered twice. Detecting & registering it as a
standalone partition was resulting in an incorrect "firmware" partition
size and possibly broken sysupgrade.
It wasn't noticed before because "rootfs" alignment depends on a kernel
size. It can happen though - depending on the configuration and the
kernel size.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Matthias Schiffer [Thu, 12 Apr 2018 05:34:57 +0000 (07:34 +0200)]
ebtables: update to latest git 2018-04-11
2e783b227766 ebt_ip: add support for matching IGMP type
b5fbb8d786c9 ebt_ip: add support for matching ICMP type and code
c5e5b784fd1a Move ICMP type handling functions from ebt_ip6 to useful_functions.c
11da52177196 include: sync linux/netfilter_bridge/ebt_ip.h with kernel
Note: the new features require at least kernel 4.17 or backported patches.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Matthias Schiffer [Tue, 10 Apr 2018 07:03:52 +0000 (09:03 +0200)]
include/kernel.mk: build kmod packages with empty FILES
kmod packages without FILES did not have an install step defined, leading
to no package being built. This affected netfilter/iptables packages, which
filter out builtin modules from FILES.
Not building a package that it is selected in .config is problematic, as
the generated empty package may be necessary to satisfy dependencies.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Daniel Engberg [Mon, 12 Mar 2018 15:59:24 +0000 (16:59 +0100)]
tools/mpfr: Update to 4.0.1
Update mpfr to 4.0.1
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Daniel Engberg [Wed, 4 Apr 2018 08:02:32 +0000 (10:02 +0200)]
tools/cmake: Update to 3.11.0
Update cmake to 3.11.0
Remove 110-alpine_musl-compat.patch as it's integrated upstream
Rename and refresh patches
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Alexander Couzens [Wed, 11 Apr 2018 01:17:44 +0000 (03:17 +0200)]
packages/uboot-omap: bugfix: serial using ns16550 fifo not enabled
The serial was working before, but not when doing copy&pasting longer
commands in a short time.
Fixes: a4def18f29e1 ("uboot-omap: Update to u-boot v2017.01")
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Lucian Cristian [Mon, 19 Feb 2018 13:53:53 +0000 (15:53 +0200)]
omap: kernel update and switch to 4.14
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
Matthias Schiffer [Tue, 10 Apr 2018 16:14:41 +0000 (18:14 +0200)]
ar71xx: increase kernel partition size for CPE/WBS 210/510
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Matthias Schiffer [Tue, 10 Apr 2018 15:26:34 +0000 (17:26 +0200)]
firmware-utils: tplink-safeloader: move CPE/WBS 210/510 version metainfo to the end
Having the metainfo between kernel and rootfs prevents us from resizing
the kernel partition as necessary.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Matthias Schiffer [Tue, 10 Apr 2018 16:06:20 +0000 (18:06 +0200)]
ar71xx: sysupgrade: improve CPE/WBS 210/510 validation, add new metadata offset
Previously, tplink_pharos_check_image() would accept any image with ELF
magic and only non-printable data in the support-list, as in this case the
while-read loop would not run at all. Add the new support-list offset and
ensure an image is only accepted when the model string is actually found.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Matthias Schiffer [Tue, 10 Apr 2018 13:19:52 +0000 (15:19 +0200)]
ar71xx: increase kernel partition size for UniFi AP Pro and Outdoor+, enable devices again
Tested on UAP Outdoor+.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Matthias Schiffer [Tue, 10 Apr 2018 11:00:42 +0000 (13:00 +0200)]
ar71xx: limit Ethernet speed of UBNT Airmax M (XM) devices to 100Mbit/s
Some Airmax devices can establish a Gigabit link even though the MAC only
supports 10/100 MBit/s, leading to broken connectivity. Prevent this from
happening by limiting the speed to 100MBit/s.
Fixes: FS#296
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Matthias Schiffer [Mon, 9 Apr 2018 17:41:26 +0000 (19:41 +0200)]
iptables: split physdev match out as a separate package
Split physdev match out of ipt-extra to allow installing ipt-extra without
pulling in br-netfilter.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Matthias Schiffer [Mon, 9 Apr 2018 17:01:56 +0000 (19:01 +0200)]
kernel: kmod-ebtables: do not depend on kmod-br-netfilter
While ebtables can be combined with br-netfilter, there is no good reason
to make it a dependency.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Matthias Schiffer [Mon, 9 Apr 2018 16:56:53 +0000 (18:56 +0200)]
kernel: unhide kmod-br-netfilter
kmod-br-netfilter is not only a support module, but can be useful on its
own, using the net.bridge.bridge-nf-call-* sysctls.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Matthias Schiffer [Mon, 9 Apr 2018 16:51:57 +0000 (18:51 +0200)]
kernel: change dependency of kmod-ebtables-* on kmod-ebtables to selecting
Non-selecting dependencies easily lead to Kconfig failures due to recursive
dependencies. We hit such an issue in Gluon; the easiest fix is to make
the dependency selecting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Hans Dedecker [Mon, 9 Apr 2018 15:19:14 +0000 (17:19 +0200)]
dnsmasq: remove example domains from rfc6761.conf (FS#1447)
RFC6771 does not exclude the forwarding of the example domain as it
states : "Caching DNS servers SHOULD NOT recognize example names as
special and SHOULD resolve them normally."
Example domains cannot be assigned to any user or person by DNS
registrars as they're registered in perpetuity to IANA meaning
they can be resolved; therefore let's remove the example domains
from the rfc6761.conf file.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Hans Dedecker [Mon, 9 Apr 2018 15:13:11 +0000 (17:13 +0200)]
odhcpd: update to latest git HEAD
31f217f router: improve RFC7084 compliancy
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Felix Fietkau [Mon, 9 Apr 2018 08:43:11 +0000 (10:43 +0200)]
mt76: update to the latest version
c66094e mt76x2: fix possible NULL pointer dereferencing in mt76x2_tx()
249fa2d mt76x2: fix warning in ieee80211_get_key_rx_seq()
54d6710 mt76: use mt76_poll_msec routine in mt76pci_load_firmware()
eb359f1 mt76x2: remove unnecessary len variable in mt76x2_eeprom_load()
7e6e00b mt76: initialize available_antennas_{tx,rx} info
6469dca mt76: add mt76_init_stream_cap routine
ced433d mt76x2: add mac80211 {set,get}_antenna callbacks
238f3f1 mt76x2: remove warnings in mt76x2_mac_write_txwi()
880611b mt7603: main: fix warning in ieee80211_get_key_rx_seq()
bc35af8 mt76x2: fix tssi initialization for 5GHz band
700ed20 mt76x2: make mt76x2_mac_reset routine static
6e7d5ce mt76x2: remove unnecessary MT_TX_ALC_CFG_4 configuration
5153ece mt76x2: set default values in TX_ALC_CFG_{1,2} for tempetaure compensation
a3e7740 mt76x2: fix tx_alc_enabled check
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rafał Miłecki [Mon, 9 Apr 2018 05:44:55 +0000 (07:44 +0200)]
ipq806x: replace linux,part-probe with a proper partitions subnode
This solution is more upstream compatible as it only requires specifying
of_match_table in the parser code and doesn't depend on linux,part-probe
which is solution made generic by a LEDE downstream patch that can't be
upstreamed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Acked-by: John Crispin <john@phrozen.org>
projects / openwrt / staging / xback.git / log