git.openwrt.org Git - openwrt/staging/blogic.git/log

MAINTAINERS: Update the ocores i2c bus driver maintainer, etc

The listed maintainer has not been responding to emails for a while.
Add myself as a second maintainer.

Add the platform data include file, which was not listed.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

i2c: omap: Use noirq system sleep pm ops to idle device for suspend

We currently get the following error with pixcir_ts driver during a
suspend resume cycle:

omap_i2c 4802a000.i2c: controller timed out
pixcir_ts 1-005c: pixcir_int_enable: can't read reg 0x34 : -110
pixcir_ts 1-005c: Failed to disable interrupt generation: -110
pixcir_ts 1-005c: Failed to stop
dpm_run_callback(): pixcir_i2c_ts_resume+0x0/0x98
[pixcir_i2c_ts] returns -110
PM: Device 1-005c failed to resume: error -110

And at least am437x based devices with pixcir_ts will fail to resume
to a touchscreen that is configured as the wakeup-source in device
tree for these devices.

This is because pixcir_ts tries to reconfigure it's registers for
noirq suspend which fails. This also leaves i2c-omap in enabled state
for suspend.

Let's fix the pixcir_ts issue and make sure i2c-omap is suspended by
adding SET_NOIRQ_SYSTEM_SLEEP_PM_OPS.

Let's also get rid of some ifdefs while at it and replace them with
__maybe_unused as SET_RUNTIME_PM_OPS and SET_NOIRQ_SYSTEM_SLEEP_PM_OPS
already deal with the various PM Kconfig options.

Reported-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Linux 5.0-rc5

Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull x86 fixes from Thomas Gleixner:
"A few updates for x86:

   - Fix an unintended sign extension issue in the fault handling code

   - Rename the new resource control config switch so it's less
     confusing

   - Avoid setting up EFI info in kexec when the EFI runtime is
     disabled.

   - Fix the microcode version check in the AMD microcode loader so it
     only loads higher version numbers and never downgrades

   - Set EFER.LME in the 32bit trampoline before returning to long mode
     to handle older AMD/KVM behaviour properly.

   - Add Darren and Andy as x86/platform reviewers"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/resctrl: Avoid confusion over the new X86_RESCTRL config
  x86/kexec: Don't setup EFI info if EFI runtime is not enabled
  x86/microcode/amd: Don't falsely trick the late loading mechanism
  MAINTAINERS: Add Andy and Darren as arch/x86/platform/ reviewers
  x86/fault: Fix sign-extend unintended sign extension
  x86/boot/compressed/64: Set EFER.LME=1 in 32-bit trampoline before returning to long mode
  x86/cpu: Add Atom Tremont (Jacobsville)

Merge branch 'smp-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull cpu hotplug fixes from Thomas Gleixner:
"Two fixes for the cpu hotplug machinery:

   - Replace the overly clever 'SMT disabled by BIOS' detection logic as
     it breaks KVM scenarios and prevents speculation control updates
     when the Hyperthreads are brought online late after boot.

   - Remove a redundant invocation of the speculation control update
     function"

* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  cpu/hotplug: Fix "SMT disabled by BIOS" detection for KVM
  x86/speculation: Remove redundant arch_smt_update() invocation

Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull perf fixes from Thomas Gleixner:
"A pile of perf updates:

   - Fix broken sanity check in the /proc/sys/kernel/perf_cpu_time_max_percent
     write handler

   - Cure a perf script crash which caused by an unitinialized data
     structure

   - Highlight the hottest instruction in perf top and not a random one

   - Cure yet another clang issue when building perf python

   - Handle topology entries with no CPU correctly in the tools

   - Handle perf data which contains both tracepoints and performance
     counter entries correctly.

   - Add a missing NULL pointer check in perf ordered_events_free()"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf script: Fix crash when processing recorded stat data
  perf top: Fix wrong hottest instruction highlighted
  perf tools: Handle TOPOLOGY headers with no CPU
  perf python: Remove -fstack-clash-protection when building with some clang versions
  perf core: Fix perf_proc_update_handler() bug
  perf script: Fix crash with printing mixed trace point and other events
  perf ordered_events: Fix crash in ordered_events__free

Merge branch 'efi-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull EFI fix from Thomas Gleixner:
"The dump info for the efi page table debugging lacks a terminator
which causes the kernel to crash when the debugfile is read"

* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/arm64: Fix debugfs crash by adding a terminator for ptdump marker

Merge tag 'for-5.0-rc4-tag' of git://git./linux/kernel/git/kdave/linux

Pull btrfs fixes from David Sterba:

- regression fix: transaction commit can run away due to delayed ref
   waiting heuristic, this is not necessary now because of the proper
   reservation mechanism introduced in 5.0

- regression fix: potential crash due to use-before-check of an ERR_PTR
   return value

- fix for transaction abort during transaction commit that needs to
   properly clean up pending block groups

- fix deadlock during b-tree node/leaf splitting, when this happens on
   some of the fundamental trees, we must prevent new tree block
   allocation to re-enter indirectly via the block group flushing path

- potential memory leak after errors during mount

* tag 'for-5.0-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: On error always free subvol_name in btrfs_mount
  btrfs: clean up pending block groups when transaction commit aborts
  btrfs: fix potential oops in device_list_add
  btrfs: don't end the transaction for delayed refs in throttle
  Btrfs: fix deadlock when allocating tree block during leaf/node split

Merge tag 'devicetree-fixes-for-5.0-3' of git://git./linux/kernel/git/robh/linux

Pull Devicetree fix from Rob Herring:
"A single fix for building DT bindings in-tree"

* tag 'devicetree-fixes-for-5.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: Fix dt_binding_check target for in tree builds

Merge tag 'riscv-for-linus-5.0-rc5' of git://git./linux/kernel/git/palmer/riscv-linux

Pull RISC-V fixes from Palmer Dabbelt:
"This contains a handful of mostly-independent patches:

   - make our port respect TIF_NEED_RESCHED, which fixes
     CONFIG_PREEMPT=y kernels

   - fix double-put of OF nodes

   - fix a misspelling of target in our Kconfig

   - generic PCIe is enabled in our defconfig

   - fix our SBI early console to properly handle line
     endings

   - fix max_low_pfn being counted in PFNs

   - a change to TASK_UNMAPPED_BASE to match what other
     arches do

  This has passed my standard 'boot Fedora' flow"

* tag 'riscv-for-linus-5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
  riscv: Adjust mmap base address at a third of task size
  riscv: fixup max_low_pfn with PFN_DOWN.
  tty/serial: use uart_console_write in the RISC-V SBL early console
  RISC-V: defconfig: Add CRYPTO_DEV_VIRTIO=y
  RISC-V: defconfig: Enable Generic PCIE by default
  RISC-V: defconfig: Move CONFIG_PCI{,E_XILINX}
  RISC-V: Kconfig: fix spelling mistake "traget" -> "target"
  RISC-V: asm/page.h: fix spelling mistake "CONFIG_64BITS" -> "CONFIG_64BIT"
  RISC-V: fix bad use of of_node_put
  RISC-V: Add _TIF_NEED_RESCHED check for kernel thread when CONFIG_PREEMPT=y

Merge tag 'for-linus-20190202' of git://git.kernel.dk/linux-block

Pull block fixes from Jens Axboe:
"A few fixes that should go into this release. This contains:

   - MD pull request from Song, fixing a recovery OOM issue (Alexei)

   - Fix for a sync related stall (Jianchao)

   - Dummy callback for timeouts (Tetsuo)

   - IDE atapi sense ordering fix (me)"

* tag 'for-linus-20190202' of git://git.kernel.dk/linux-block:
  ide: ensure atapi sense request aren't preempted
  blk-mq: fix a hung issue when fsync
  block: pass no-op callback to INIT_WORK().
  md/raid5: fix 'out of memory' during raid cache recovery

Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi

Pull SCSI fixes from James Bottomley:
"Five minor bug fixes.

  The libfc one is a tiny memory leak, the zfcp one is an incorrect user
  visible parameter and the rest are on error legs or obscure features"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: 53c700: pass correct "dev" to dma_alloc_attrs()
  scsi: bnx2fc: Fix error handling in probe()
  scsi: scsi_debug: fix write_same with virtual_gb problem
  scsi: libfc: free skb when receiving invalid flogi resp
  scsi: zfcp: fix sysfs block queue limit output for max_segment_size

Merge branch 'akpm' (patches from Andrew)

Merge misc fixes from Andrew Morton:
"24 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (24 commits)
  autofs: fix error return in autofs_fill_super()
  autofs: drop dentry reference only when it is never used
  fs/drop_caches.c: avoid softlockups in drop_pagecache_sb()
  mm: migrate: don't rely on __PageMovable() of newpage after unlocking it
  psi: clarify the Kconfig text for the default-disable option
  mm, memory_hotplug: __offline_pages fix wrong locking
  mm: hwpoison: use do_send_sig_info() instead of force_sig()
  kasan: mark file common so ftrace doesn't trace it
  init/Kconfig: fix grammar by moving a closing parenthesis
  lib/test_kmod.c: potential double free in error handling
  mm, oom: fix use-after-free in oom_kill_process
  mm/hotplug: invalid PFNs from pfn_to_online_page()
  mm,memory_hotplug: fix scan_movable_pages() for gigantic hugepages
  psi: fix aggregation idle shut-off
  mm, memory_hotplug: test_pages_in_a_zone do not pass the end of zone
  mm, memory_hotplug: is_mem_section_removable do not pass the end of a zone
  oom, oom_reaper: do not enqueue same task twice
  mm: migrate: make buffer_migrate_page_norefs() actually succeed
  kernel/exit.c: release ptraced tasks before zap_pid_ns_processes
  x86_64: increase stack size for KASAN_EXTRA
  ...

efi/arm64: Fix debugfs crash by adding a terminator for ptdump marker

When reading 'efi_page_tables' debugfs triggers an out-of-bounds access here:

  arch/arm64/mm/dump.c: 282
  if (addr >= st->marker[1].start_address) {

called from:

  arch/arm64/mm/dump.c: 331
  note_page(st, addr, 2, pud_val(pud));

because st->marker++ is is called after "UEFI runtime end" which is the
last element in addr_marker[]. Therefore, add a terminator like the one
for kernel_page_tables, so it can be skipped to print out non-existent
markers.

Here's the KASAN bug report:

  # cat /sys/kernel/debug/efi_page_tables
  ---[ UEFI runtime start ]---
  0x0000000020000000-0x0000000020010000          64K PTE       RW NX SHD AF ...
  0x0000000020200000-0x0000000021340000       17664K PTE       RW NX SHD AF ...
  ...
  0x0000000021920000-0x0000000021950000         192K PTE       RW x  SHD AF ...
  0x0000000021950000-0x00000000219a0000         320K PTE       RW NX SHD AF ...
  ---[ UEFI runtime end ]---
  ---[ (null) ]---
  ---[ (null) ]---

   BUG: KASAN: global-out-of-bounds in note_page+0x1f0/0xac0
   Read of size 8 at addr ffff2000123f2ac0 by task read_all/42464
   Call trace:
    dump_backtrace+0x0/0x298
    show_stack+0x24/0x30
    dump_stack+0xb0/0xdc
    print_address_description+0x64/0x2b0
    kasan_report+0x150/0x1a4
    __asan_report_load8_noabort+0x30/0x3c
    note_page+0x1f0/0xac0
    walk_pgd+0xb4/0x244
    ptdump_walk_pgd+0xec/0x140
    ptdump_show+0x40/0x50
    seq_read+0x3f8/0xad0
    full_proxy_read+0x9c/0xc0
    __vfs_read+0xfc/0x4c8
    vfs_read+0xec/0x208
    ksys_read+0xd0/0x15c
    __arm64_sys_read+0x84/0x94
    el0_svc_handler+0x258/0x304
    el0_svc+0x8/0xc

  The buggy address belongs to the variable:
   __compound_literal.0+0x20/0x800

  Memory state around the buggy address:
   ffff2000123f2980: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
   ffff2000123f2a00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 fa
  >ffff2000123f2a80: fa fa fa fa 00 00 00 00 fa fa fa fa 00 00 00 00
                                            ^
   ffff2000123f2b00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
   ffff2000123f2b80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0

[ ardb: fix up whitespace ]
[ mingo: fix up some moar ]

Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 9d80448ac92b ("efi/arm64: Add debugfs node to dump UEFI runtime page tables")
Link: http://lkml.kernel.org/r/20190202095017.13799-2-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

x86/resctrl: Avoid confusion over the new X86_RESCTRL config

"Resource Control" is a very broad term for this CPU feature, and a term
that is also associated with containers, cgroups etc. This can easily
cause confusion.

Make the user prompt more specific. Match the config symbol name.

[ bp: In the future, the corresponding ARM arch-specific code will be
under ARM_CPU_RESCTRL and the arch-agnostic bits will be carved out
under the CPU_RESCTRL umbrella symbol. ]

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Babu Moger <Babu.Moger@amd.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morse <james.morse@arm.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: linux-doc@vger.kernel.org
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Pu Wen <puwen@hygon.cn>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190130195621.GA30653@cmpxchg.org

Merge tag 'xtensa-20190201' of git://github.com/jcmvbkbc/linux-xtensa

Pull xtensa fixes from Max Filippov:

- fix ccount_timer_shutdown for secondary CPUs

- fix secondary CPU initialization

- fix secondary CPU reset vector clash with double exception vector

- fix present CPUs when booting with 'maxcpus' parameter

- limit possible CPUs by configured NR_CPUS

- issue a warning if xtensa PIC is asked to retrigger anything other
   than software IRQ

- fix masking/unmasking of the first two IRQs on xtensa MX PIC

- fix typo in Kconfig description for user space unaligned access
   feature

- fix Kconfig warning for selecting BUILTIN_DTB

* tag 'xtensa-20190201' of git://github.com/jcmvbkbc/linux-xtensa:
  xtensa: SMP: limit number of possible CPUs by NR_CPUS
  xtensa: rename BUILTIN_DTB to BUILTIN_DTB_SOURCE
  xtensa: Fix typo use space=>user space
  drivers/irqchip: xtensa-mx: fix mask and unmask
  drivers/irqchip: xtensa: add warning to irq_retrigger
  xtensa: SMP: mark each possible CPU as present
  xtensa: smp_lx200_defconfig: fix vectors clash
  xtensa: SMP: fix secondary CPU initialization
  xtensa: SMP: fix ccount_timer_shutdown

Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux

Pull arm64 fixes from Will Deacon:
"Although we're still debugging a few minor arm64-specific issues in
  mainline, I didn't want to hold this lot up in the meantime.

  We've got an additional KASLR fix after the previous one wasn't quite
  complete, a fix for a performance regression when mapping executable
  pages into userspace and some fixes for kprobe blacklisting. All
  candidates for stable.

  Summary:

   - Fix module loading when KASLR is configured but disabled at runtime

   - Fix accidental IPI when mapping user executable pages

   - Ensure hyp-stub and KVM world switch code cannot be kprobed"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: hibernate: Clean the __hyp_text to PoC after resume
  arm64: hyp-stub: Forbid kprobing of the hyp-stub
  arm64: kprobe: Always blacklist the KVM world-switch code
  arm64: kaslr: ensure randomized quantities are clean also when kaslr is off
  arm64: Do not issue IPIs for user executable ptes

Merge tag '5.0-rc4-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6

Pull smb3 fixes from Steve French:
"SMB3 fixes, some from this week's SMB3 test evemt, 5 for stable and a
  particularly important one for queryxattr (see xfstests 70 and 117)"

* tag '5.0-rc4-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: update internal module version number
  CIFS: fix use-after-free of the lease keys
  CIFS: Do not consider -ENODATA as stat failure for reads
  CIFS: Do not count -ENODATA as failure for query directory
  CIFS: Fix trace command logging for SMB2 reads and writes
  CIFS: Fix possible oops and memory leaks in async IO
  cifs: limit amount of data we request for xattrs to CIFSMaxBufSize
  cifs: fix computation for MAX_SMB2_HDR_SIZE

Merge tag 'apparmor-pr-2019-02-01' of git://git./linux/kernel/git/jj/linux-apparmor

Pull apparmor bug fixes from John Johansen:
"Two bug fixes for apparmor:

   - Fix aa_label_build() error handling for failed merges

   - Fix warning about unused function apparmor_ipv6_postroute"

* tag 'apparmor-pr-2019-02-01' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor:
  apparmor: Fix aa_label_build() error handling for failed merges
  apparmor: Fix warning about unused function apparmor_ipv6_postroute

autofs: fix error return in autofs_fill_super()

In autofs_fill_super() on error of get inode/make root dentry the return
should be ENOMEM as this is the only failure case of the called
functions.

Link: http://lkml.kernel.org/r/154725123240.11260.796773942606871359.stgit@pluto-themaw-net
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

autofs: drop dentry reference only when it is never used

autofs_expire_run() calls dput(dentry) to drop the reference count of
dentry. However, dentry is read via autofs_dentry_ino(dentry) after
that. This may result in a use-free-bug. The patch drops the reference
count of dentry only when it is never used.

Link: http://lkml.kernel.org/r/154725122396.11260.16053424107144453867.stgit@pluto-themaw-net
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/drop_caches.c: avoid softlockups in drop_pagecache_sb()

When superblock has lots of inodes without any pagecache (like is the
case for /proc), drop_pagecache_sb() will iterate through all of them
without dropping sb->s_inode_list_lock which can lead to softlockups
(one of our customers hit this).

Fix the problem by going to the slow path and doing cond_resched() in
case the process needs rescheduling.

Link: http://lkml.kernel.org/r/20190114085343.15011-1-jack@suse.cz
Signed-off-by: Jan Kara <jack@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: migrate: don't rely on __PageMovable() of newpage after unlocking it

We had a race in the old balloon compaction code before b1123ea6d3b3
("mm: balloon: use general non-lru movable page feature") refactored it
that became visible after backporting 195a8c43e93d ("virtio-balloon:
deflate via a page list") without the refactoring.

The bug existed from commit d6d86c0a7f8d ("mm/balloon_compaction:
redesign ballooned pages management") till b1123ea6d3b3 ("mm: balloon:
use general non-lru movable page feature").  d6d86c0a7f8d
("mm/balloon_compaction: redesign ballooned pages management") was
backported to 3.12, so the broken kernels are stable kernels [3.12 -
4.7].

There was a subtle race between dropping the page lock of the newpage in
__unmap_and_move() and checking for __is_movable_balloon_page(newpage).

Just after dropping this page lock, virtio-balloon could go ahead and
deflate the newpage, effectively dequeueing it and clearing PageBalloon,
in turn making __is_movable_balloon_page(newpage) fail.

This resulted in dropping the reference of the newpage via
putback_lru_page(newpage) instead of put_page(newpage), leading to
page->lru getting modified and a !LRU page ending up in the LRU lists.
With 195a8c43e93d ("virtio-balloon: deflate via a page list")
backported, one would suddenly get corrupted lists in
release_pages_balloon():

- WARNING: CPU: 13 PID: 6586 at lib/list_debug.c:59 __list_del_entry+0xa1/0xd0
- list_del corruption. prev->next should be ffffe253961090a0, but was dead000000000100

Nowadays this race is no longer possible, but it is hidden behind very
ugly handling of __ClearPageMovable() and __PageMovable().

__ClearPageMovable() will not make __PageMovable() fail, only
PageMovable().  So the new check (__PageMovable(newpage)) will still
hold even after newpage was dequeued by virtio-balloon.

If anybody would ever change that special handling, the BUG would be
introduced again.  So instead, make it explicit and use the information
of the original isolated page before migration.

This patch can be backported fairly easy to stable kernels (in contrast
to the refactoring).

Link: http://lkml.kernel.org/r/20190129233217.10747-1-david@redhat.com
Fixes: d6d86c0a7f8d ("mm/balloon_compaction: redesign ballooned pages management")
Signed-off-by: David Hildenbrand <david@redhat.com>
Reported-by: Vratislav Bendel <vbendel@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Rafael Aquini <aquini@redhat.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Vratislav Bendel <vbendel@redhat.com>
Cc: Rafael Aquini <aquini@redhat.com>
Cc: Konstantin Khlebnikov <k.khlebnikov@samsung.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: <stable@vger.kernel.org> [3.12 - 4.7]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

psi: clarify the Kconfig text for the default-disable option

The current help text caused some confusion in online forums about
whether or not to default-enable or default-disable psi in vendor
kernels. This is because it doesn't communicate the reason for why we
made this setting configurable in the first place: that the overhead is
non-zero in an artificial scheduler stress test.

Since this isn't representative of real workloads, and the effect was
not measurable in scheduler-heavy real world applications such as the
webservers and memcache installations at Facebook, it's fair to point
out that this is a pretty cautious option to select.

Link: http://lkml.kernel.org/r/20190129233617.16767-1-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm, memory_hotplug: __offline_pages fix wrong locking

Jan has noticed that we do double unlock on some failure paths when
offlining a page range. This is indeed the case when
test_pages_in_a_zone respp. start_isolate_page_range fail. This was an
omission when forward porting the debugging patch from an older kernel.

Fix the issue by dropping mem_hotplug_done from the failure condition
and keeping the single unlock in the catch all failure path.

Link: http://lkml.kernel.org/r/20190115120307.22768-1-mhocko@kernel.org
Fixes: 7960509329c2 ("mm, memory_hotplug: print reason for the offlining failure")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Jan Kara <jack@suse.cz>
Reviewed-by: Jan Kara <jack@suse.cz>
Tested-by: Jan Kara <jack@suse.cz>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: hwpoison: use do_send_sig_info() instead of force_sig()

Currently memory_failure() is racy against process's exiting, which
results in kernel crash by null pointer dereference.

The root cause is that memory_failure() uses force_sig() to forcibly
kill asynchronous (meaning not in the current context) processes.  As
discussed in thread https://lkml.org/lkml/2010/6/8/236 years ago for OOM
fixes, this is not a right thing to do.  OOM solves this issue by using
do_send_sig_info() as done in commit d2d393099de2 ("signal:
oom_kill_task: use SEND_SIG_FORCED instead of force_sig()"), so this
patch is suggesting to do the same for hwpoison.  do_send_sig_info()
properly accesses to siglock with lock_task_sighand(), so is free from
the reported race.

I confirmed that the reported bug reproduces with inserting some delay
in kill_procs(), and it never reproduces with this patch.

Note that memory_failure() can send another type of signal using
force_sig_mceerr(), and the reported race shouldn't happen on it because
force_sig_mceerr() is called only for synchronous processes (i.e.
BUS_MCEERR_AR happens only when some process accesses to the corrupted
memory.)

Link: http://lkml.kernel.org/r/20190116093046.GA29835@hori1.linux.bs1.fc.nec.co.jp
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reported-by: Jane Chu <jane.chu@oracle.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: William Kucharski <william.kucharski@oracle.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kasan: mark file common so ftrace doesn't trace it

When option CONFIG_KASAN is enabled toghether with ftrace, function
ftrace_graph_caller() gets in to a recursion, via functions
kasan_check_read() and kasan_check_write().

Breakpoint 2, ftrace_graph_caller () at ../arch/arm64/kernel/entry-ftrace.S:179
179             mcount_get_pc             x0    //     function's pc
(gdb) bt
#0  ftrace_graph_caller () at ../arch/arm64/kernel/entry-ftrace.S:179
#1  0xffffff90101406c8 in ftrace_caller () at ../arch/arm64/kernel/entry-ftrace.S:151
#2  0xffffff90106fd084 in kasan_check_write (p=0xffffffc06c170878, size=4) at ../mm/kasan/common.c:105
#3  0xffffff90104a2464 in atomic_add_return (v=<optimized out>, i=<optimized out>) at ./include/generated/atomic-instrumented.h:71
#4  atomic_inc_return (v=<optimized out>) at ./include/generated/atomic-fallback.h:284
#5  trace_graph_entry (trace=0xffffffc03f5ff380) at ../kernel/trace/trace_functions_graph.c:441
#6  0xffffff9010481774 in trace_graph_entry_watchdog (trace=<optimized out>) at ../kernel/trace/trace_selftest.c:741
#7  0xffffff90104a185c in function_graph_enter (ret=<optimized out>, func=<optimized out>, frame_pointer=18446743799894897728, retp=<optimized out>) at ../kernel/trace/trace_functions_graph.c:196
#8  0xffffff9010140628 in prepare_ftrace_return (self_addr=18446743592948977792, parent=0xffffffc03f5ff418, frame_pointer=18446743799894897728) at ../arch/arm64/kernel/ftrace.c:231
#9  0xffffff90101406f4 in ftrace_graph_caller () at ../arch/arm64/kernel/entry-ftrace.S:182
Backtrace stopped: previous frame identical to this frame (corrupt stack?)
(gdb)

Rework so that the kasan implementation isn't traced.

Link: http://lkml.kernel.org/r/20181212183447.15890-1-anders.roxell@linaro.org
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

init/Kconfig: fix grammar by moving a closing parenthesis

Link: http://lkml.kernel.org/r/20190129150813.15785-1-j.neuschaefer@gmx.net
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lib/test_kmod.c: potential double free in error handling

There is a copy and paste bug so we set "config->test_driver" to NULL
twice instead of setting "config->test_fs". Smatch complains that it
leads to a double free:

lib/test_kmod.c:840 __kmod_config_init() warn: 'config->test_fs' double freed

Link: http://lkml.kernel.org/r/20190121140011.GA14283@kadam
Fixes: d9c6a72d6fa2 ("kmod: add test driver to stress test the module loader")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm, oom: fix use-after-free in oom_kill_process

Syzbot instance running on upstream kernel found a use-after-free bug in
oom_kill_process.  On further inspection it seems like the process
selected to be oom-killed has exited even before reaching
read_lock(&tasklist_lock) in oom_kill_process().  More specifically the
tsk->usage is 1 which is due to get_task_struct() in oom_evaluate_task()
and the put_task_struct within for_each_thread() frees the tsk and
for_each_thread() tries to access the tsk.  The easiest fix is to do
get/put across the for_each_thread() on the selected task.

Now the next question is should we continue with the oom-kill as the
previously selected task has exited? However before adding more
complexity and heuristics, let's answer why we even look at the children
of oom-kill selected task? The select_bad_process() has already selected
the worst process in the system/memcg.  Due to race, the selected
process might not be the worst at the kill time but does that matter?
The userspace can use the oom_score_adj interface to prefer children to
be killed before the parent.  I looked at the history but it seems like
this is there before git history.

Link: http://lkml.kernel.org/r/20190121215850.221745-1-shakeelb@google.com
Reported-by: syzbot+7fbbfa368521945f0e3d@syzkaller.appspotmail.com
Fixes: 6b0c81b3be11 ("mm, oom: reduce dependency on tasklist_lock")
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Reviewed-by: Roman Gushchin <guro@fb.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/hotplug: invalid PFNs from pfn_to_online_page()

On an arm64 ThunderX2 server, the first kmemleak scan would crash [1]
with CONFIG_DEBUG_VM_PGFLAGS=y due to page_to_nid() found a pfn that is
not directly mapped (MEMBLOCK_NOMAP).  Hence, the page->flags is
uninitialized.

This is due to the commit 9f1eb38e0e11 ("mm, kmemleak: little
optimization while scanning") starts to use pfn_to_online_page() instead
of pfn_valid().  However, in the CONFIG_MEMORY_HOTPLUG=y case,
pfn_to_online_page() does not call memblock_is_map_memory() while
pfn_valid() does.

Historically, the commit 68709f45385a ("arm64: only consider memblocks
with NOMAP cleared for linear mapping") causes pages marked as nomap
being no long reassigned to the new zone in memmap_init_zone() by
calling __init_single_page().

Since the commit 2d070eab2e82 ("mm: consider zone which is not fully
populated to have holes") introduced pfn_to_online_page() and was
designed to return a valid pfn only, but it is clearly broken on arm64.

Therefore, let pfn_to_online_page() call pfn_valid_within(), so it can
handle nomap thanks to the commit f52bb98f5ade ("arm64: mm: always
enable CONFIG_HOLES_IN_ZONE"), while it will be optimized away on
architectures where have no HOLES_IN_ZONE.

[1]
  Unable to handle kernel NULL pointer dereference at virtual address 0000000000000006
  Mem abort info:
    ESR = 0x96000005
    Exception class = DABT (current EL), IL = 32 bits
    SET = 0, FnV = 0
    EA = 0, S1PTW = 0
  Data abort info:
    ISV = 0, ISS = 0x00000005
    CM = 0, WnR = 0
  Internal error: Oops: 96000005 [#1] SMP
  CPU: 60 PID: 1408 Comm: kmemleak Not tainted 5.0.0-rc2+ #8
  pstate: 60400009 (nZCv daif +PAN -UAO)
  pc : page_mapping+0x24/0x144
  lr : __dump_page+0x34/0x3dc
  sp : ffff00003a5cfd10
  x29: ffff00003a5cfd10 x28: 000000000000802f
  x27: 0000000000000000 x26: 0000000000277d00
  x25: ffff000010791f56 x24: ffff7fe000000000
  x23: ffff000010772f8b x22: ffff00001125f670
  x21: ffff000011311000 x20: ffff000010772f8b
  x19: fffffffffffffffe x18: 0000000000000000
  x17: 0000000000000000 x16: 0000000000000000
  x15: 0000000000000000 x14: ffff802698b19600
  x13: ffff802698b1a200 x12: ffff802698b16f00
  x11: ffff802698b1a400 x10: 0000000000001400
  x9 : 0000000000000001 x8 : ffff00001121a000
  x7 : 0000000000000000 x6 : ffff0000102c53b8
  x5 : 0000000000000000 x4 : 0000000000000003
  x3 : 0000000000000100 x2 : 0000000000000000
  x1 : ffff000010772f8b x0 : ffffffffffffffff
  Process kmemleak (pid: 1408, stack limit = 0x(____ptrval____))
  Call trace:
   page_mapping+0x24/0x144
   __dump_page+0x34/0x3dc
   dump_page+0x28/0x4c
   kmemleak_scan+0x4ac/0x680
   kmemleak_scan_thread+0xb4/0xdc
   kthread+0x12c/0x13c
   ret_from_fork+0x10/0x18
  Code: d503201f f9400660 36000040 d1000413 (f9400661)
  ---[ end trace 4d4bd7f573490c8e ]---
  Kernel panic - not syncing: Fatal exception
  SMP: stopping secondary CPUs
  Kernel Offset: disabled
  CPU features: 0x002,20000c38
  Memory Limit: none
  ---[ end Kernel panic - not syncing: Fatal exception ]---

Link: http://lkml.kernel.org/r/20190122132916.28360-1-cai@lca.pw
Fixes: 9f1eb38e0e11 ("mm, kmemleak: little optimization while scanning")
Signed-off-by: Qian Cai <cai@lca.pw>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm,memory_hotplug: fix scan_movable_pages() for gigantic hugepages

This is the same sort of error we saw in commit 17e2e7d7e1b8 ("mm,
page_alloc: fix has_unmovable_pages for HugePages").

Gigantic hugepages cross several memblocks, so it can be that the page
we get in scan_movable_pages() is a page-tail belonging to a
1G-hugepage.  If that happens, page_hstate()->size_to_hstate() will
return NULL, and we will blow up in hugepage_migration_supported().

The splat is as follows:

  BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
  #PF error: [normal kernel read fault]
  PGD 0 P4D 0
  Oops: 0000 [#1] SMP PTI
  CPU: 1 PID: 1350 Comm: bash Tainted: G            E     5.0.0-rc1-mm1-1-default+ #27
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.0.0-prebuilt.qemu-project.org 04/01/2014
  RIP: 0010:__offline_pages+0x6ae/0x900
  Call Trace:
   memory_subsys_offline+0x42/0x60
   device_offline+0x80/0xa0
   state_store+0xab/0xc0
   kernfs_fop_write+0x102/0x180
   __vfs_write+0x26/0x190
   vfs_write+0xad/0x1b0
   ksys_write+0x42/0x90
   do_syscall_64+0x5b/0x180
   entry_SYSCALL_64_after_hwframe+0x44/0xa9
  Modules linked in: af_packet(E) xt_tcpudp(E) ipt_REJECT(E) xt_conntrack(E) nf_conntrack(E) nf_defrag_ipv4(E) ip_set(E) nfnetlink(E) ebtable_nat(E) ebtable_broute(E) bridge(E) stp(E) llc(E) iptable_mangle(E) iptable_raw(E) iptable_security(E) ebtable_filter(E) ebtables(E) iptable_filter(E) ip_tables(E) x_tables(E) kvm_intel(E) kvm(E) irqbypass(E) crct10dif_pclmul(E) crc32_pclmul(E) ghash_clmulni_intel(E) bochs_drm(E) ttm(E) aesni_intel(E) drm_kms_helper(E) aes_x86_64(E) crypto_simd(E) cryptd(E) glue_helper(E) drm(E) virtio_net(E) syscopyarea(E) sysfillrect(E) net_failover(E) sysimgblt(E) pcspkr(E) failover(E) i2c_piix4(E) fb_sys_fops(E) parport_pc(E) parport(E) button(E) btrfs(E) libcrc32c(E) xor(E) zstd_decompress(E) zstd_compress(E) xxhash(E) raid6_pq(E) sd_mod(E) ata_generic(E) ata_piix(E) ahci(E) libahci(E) libata(E) crc32c_intel(E) serio_raw(E) virtio_pci(E) virtio_ring(E) virtio(E) sg(E) scsi_mod(E) autofs4(E)

[akpm@linux-foundation.org: fix brace layout, per David.  Reduce indentation]
Link: http://lkml.kernel.org/r/20190122154407.18417-1-osalvador@suse.de
Signed-off-by: Oscar Salvador <osalvador@suse.de>
Reviewed-by: Anthony Yznaga <anthony.yznaga@oracle.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

psi: fix aggregation idle shut-off

psi has provisions to shut off the periodic aggregation worker when
there is a period of no task activity - and thus no data that needs
aggregating.  However, while developing psi monitoring, Suren noticed
that the aggregation clock currently won't stay shut off for good.

Debugging this revealed a flaw in the idle design: an aggregation run
will see no task activity and decide to go to sleep; shortly thereafter,
the kworker thread that executed the aggregation will go idle and cause
a scheduling change, during which the psi callback will kick the
!pending worker again.  This will ping-pong forever, and is equivalent
to having no shut-off logic at all (but with more code!)

Fix this by exempting aggregation workers from psi's clock waking logic
when the state change is them going to sleep.  To do this, tag workers
with the last work function they executed, and if in psi we see a worker
going to sleep after aggregating psi data, we will not reschedule the
aggregation work item.

What if the worker is also executing other items before or after?

Any psi state times that were incurred by work items preceding the
aggregation work will have been collected from the per-cpu buckets
during the aggregation itself.  If there are work items following the
aggregation work, the worker's last_func tag will be overwritten and the
aggregator will be kept alive to process this genuine new activity.

If the aggregation work is the last thing the worker does, and we decide
to go idle, the brief period of non-idle time incurred between the
aggregation run and the kworker's dequeue will be stranded in the
per-cpu buckets until the clock is woken by later activity.  But that
should not be a problem.  The buckets can hold 4s worth of time, and
future activity will wake the clock with a 2s delay, giving us 2s worth
of data we can leave behind when disabling aggregation.  If it takes a
worker more than two seconds to go idle after it finishes its last work
item, we likely have bigger problems in the system, and won't notice one
sample that was averaged with a bogus per-CPU weight.

Link: http://lkml.kernel.org/r/20190116193501.1910-1-hannes@cmpxchg.org
Fixes: eb414681d5a0 ("psi: pressure stall information for CPU, memory, and IO")
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: Suren Baghdasaryan <surenb@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm, memory_hotplug: test_pages_in_a_zone do not pass the end of zone

If memory end is not aligned with the sparse memory section boundary,
the mapping of such a section is only partly initialized.  This may lead
to VM_BUG_ON due to uninitialized struct pages access from
test_pages_in_a_zone() function triggered by memory_hotplug sysfs
handlers.

Here are the the panic examples:
CONFIG_DEBUG_VM_PGFLAGS=y
kernel parameter mem=2050M
--------------------------
page:000003d082008000 is uninitialized and poisoned
page dumped because: VM_BUG_ON_PAGE(PagePoisoned(p))
Call Trace:
   test_pages_in_a_zone+0xde/0x160
   show_valid_zones+0x5c/0x190
   dev_attr_show+0x34/0x70
   sysfs_kf_seq_show+0xc8/0x148
   seq_read+0x204/0x480
   __vfs_read+0x32/0x178
   vfs_read+0x82/0x138
   ksys_read+0x5a/0xb0
   system_call+0xdc/0x2d8
Last Breaking-Event-Address:
   test_pages_in_a_zone+0xde/0x160
Kernel panic - not syncing: Fatal exception: panic_on_oops

Fix this by checking whether the pfn to check is within the zone.

[mhocko@suse.com: separated this change from http://lkml.kernel.org/r/20181105150401.97287-2-zaslonko@linux.ibm.com]
Link: http://lkml.kernel.org/r/20190128144506.15603-3-mhocko@kernel.org
[mhocko@suse.com: separated this change from
http://lkml.kernel.org/r/20181105150401.97287-2-zaslonko@linux.ibm.com]
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Mikhail Zaslonko <zaslonko@linux.ibm.com>
Tested-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Tested-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm, memory_hotplug: is_mem_section_removable do not pass the end of a zone

Patch series "mm, memory_hotplug: fix uninitialized pages fallouts", v2.

Mikhail Zaslonko has posted fixes for the two bugs quite some time ago
[1].  I have pushed back on those fixes because I believed that it is
much better to plug the problem at the initialization time rather than
play whack-a-mole all over the hotplug code and find all the places
which expect the full memory section to be initialized.

We have ended up with commit 2830bf6f05fb ("mm, memory_hotplug:
initialize struct pages for the full memory section") merged and cause a
regression [2][3].  The reason is that there might be memory layouts
when two NUMA nodes share the same memory section so the merged fix is
simply incorrect.

In order to plug this hole we really have to be zone range aware in
those handlers.  I have split up the original patch into two.  One is
unchanged (patch 2) and I took a different approach for `removable'
crash.

[1] http://lkml.kernel.org/r/20181105150401.97287-2-zaslonko@linux.ibm.com
[2] https://bugzilla.redhat.com/show_bug.cgi?id=1666948
[3] http://lkml.kernel.org/r/20190125163938.GA20411@dhcp22.suse.cz

This patch (of 2):

Mikhail has reported the following VM_BUG_ON triggered when reading sysfs
removable state of a memory block:

page:000003d08300c000 is uninitialized and poisoned
page dumped because: VM_BUG_ON_PAGE(PagePoisoned(p))
Call Trace:
   is_mem_section_removable+0xb4/0x190
   show_mem_removable+0x9a/0xd8
   dev_attr_show+0x34/0x70
   sysfs_kf_seq_show+0xc8/0x148
   seq_read+0x204/0x480
   __vfs_read+0x32/0x178
   vfs_read+0x82/0x138
   ksys_read+0x5a/0xb0
   system_call+0xdc/0x2d8
Last Breaking-Event-Address:
   is_mem_section_removable+0xb4/0x190
Kernel panic - not syncing: Fatal exception: panic_on_oops

The reason is that the memory block spans the zone boundary and we are
stumbling over an unitialized struct page.  Fix this by enforcing zone
range in is_mem_section_removable so that we never run away from a zone.

Link: http://lkml.kernel.org/r/20190128144506.15603-2-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Mikhail Zaslonko <zaslonko@linux.ibm.com>
Debugged-by: Mikhail Zaslonko <zaslonko@linux.ibm.com>
Tested-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Tested-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

oom, oom_reaper: do not enqueue same task twice

Arkadiusz reported that enabling memcg's group oom killing causes
strange memcg statistics where there is no task in a memcg despite the
number of tasks in that memcg is not 0.  It turned out that there is a
bug in wake_oom_reaper() which allows enqueuing same task twice which
makes impossible to decrease the number of tasks in that memcg due to a
refcount leak.

This bug existed since the OOM reaper became invokable from
task_will_free_mem(current) path in out_of_memory() in Linux 4.7,

  T1@P1     |T2@P1     |T3@P1     |OOM reaper
  ----------+----------+----------+------------
                                   # Processing an OOM victim in a different memcg domain.
                        try_charge()
                          mem_cgroup_out_of_memory()
                            mutex_lock(&oom_lock)
             try_charge()
               mem_cgroup_out_of_memory()
                 mutex_lock(&oom_lock)
  try_charge()
    mem_cgroup_out_of_memory()
      mutex_lock(&oom_lock)
                            out_of_memory()
                              oom_kill_process(P1)
                                do_send_sig_info(SIGKILL, @P1)
                                mark_oom_victim(T1@P1)
                                wake_oom_reaper(T1@P1) # T1@P1 is enqueued.
                            mutex_unlock(&oom_lock)
                 out_of_memory()
                   mark_oom_victim(T2@P1)
                   wake_oom_reaper(T2@P1) # T2@P1 is enqueued.
                 mutex_unlock(&oom_lock)
      out_of_memory()
        mark_oom_victim(T1@P1)
        wake_oom_reaper(T1@P1) # T1@P1 is enqueued again due to oom_reaper_list == T2@P1 && T1@P1->oom_reaper_list == NULL.
      mutex_unlock(&oom_lock)
                                   # Completed processing an OOM victim in a different memcg domain.
                                   spin_lock(&oom_reaper_lock)
                                   # T1P1 is dequeued.
                                   spin_unlock(&oom_reaper_lock)

but memcg's group oom killing made it easier to trigger this bug by
calling wake_oom_reaper() on the same task from one out_of_memory()
request.

Fix this bug using an approach used by commit 855b018325737f76 ("oom,
oom_reaper: disable oom_reaper for oom_kill_allocating_task").  As a
side effect of this patch, this patch also avoids enqueuing multiple
threads sharing memory via task_will_free_mem(current) path.

Link: http://lkml.kernel.org/r/e865a044-2c10-9858-f4ef-254bc71d6cc2@i-love.sakura.ne.jp
Link: http://lkml.kernel.org/r/5ee34fc6-1485-34f8-8790-903ddabaa809@i-love.sakura.ne.jp
Fixes: af8e15cc85a25315 ("oom, oom_reaper: do not enqueue task if it is on the oom_reaper_list head")
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: Arkadiusz Miskiewicz <arekm@maven.pl>
Tested-by: Arkadiusz Miskiewicz <arekm@maven.pl>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Roman Gushchin <guro@fb.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Aleksa Sarai <asarai@suse.de>
Cc: Jay Kamat <jgkamat@fb.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: migrate: make buffer_migrate_page_norefs() actually succeed

Currently, buffer_migrate_page_norefs() was constantly failing because
buffer_migrate_lock_buffers() grabbed reference on each buffer. In
fact, there's no reason for buffer_migrate_lock_buffers() to grab any
buffer references as the page is locked during all our operation and
thus nobody can reclaim buffers from the page.

So remove grabbing of buffer references which also makes
buffer_migrate_page_norefs() succeed.

Link: http://lkml.kernel.org/r/20190116131217.7226-1-jack@suse.cz
Fixes: 89cb0888ca14 "mm: migrate: provide buffer_migrate_page_norefs()"
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Zi Yan <zi.yan@cs.rutgers.edu>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel/exit.c: release ptraced tasks before zap_pid_ns_processes

Currently, exit_ptrace() adds all ptraced tasks in a dead list, then
zap_pid_ns_processes() waits on all tasks in a current pidns, and only
then are tasks from the dead list released.

zap_pid_ns_processes() can get stuck on waiting tasks from the dead
list. In this case, we will have one unkillable process with one or
more dead children.

Thanks to Oleg for the advice to release tasks in find_child_reaper().

Link: http://lkml.kernel.org/r/20190110175200.12442-1-avagin@gmail.com
Fixes: 7c8bd2322c7f ("exit: ptrace: shift "reap dead" code from exit_ptrace() to forget_original_parent()")
Signed-off-by: Andrei Vagin <avagin@gmail.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

x86_64: increase stack size for KASAN_EXTRA

If the kernel is configured with KASAN_EXTRA, the stack size is
increasted significantly because this option sets "-fstack-reuse" to
"none" in GCC [1].  As a result, it triggers stack overrun quite often
with 32k stack size compiled using GCC 8.  For example, this reproducer

  https://github.com/linux-test-project/ltp/blob/master/testcases/kernel/syscalls/madvise/madvise06.c

triggers a "corrupted stack end detected inside scheduler" very reliably
with CONFIG_SCHED_STACK_END_CHECK enabled.

There are just too many functions that could have a large stack with
KASAN_EXTRA due to large local variables that have been called over and
over again without being able to reuse the stacks.  Some noticiable ones
are

  size
  7648 shrink_page_list
  3584 xfs_rmap_convert
  3312 migrate_page_move_mapping
  3312 dev_ethtool
  3200 migrate_misplaced_transhuge_page
  3168 copy_process

There are other 49 functions are over 2k in size while compiling kernel
with "-Wframe-larger-than=" even with a related minimal config on this
machine.  Hence, it is too much work to change Makefiles for each object
to compile without "-fsanitize-address-use-after-scope" individually.

[1] https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81715#c23

Although there is a patch in GCC 9 to help the situation, GCC 9 probably
won't be released in a few months and then it probably take another
6-month to 1-year for all major distros to include it as a default.
Hence, the stack usage with KASAN_EXTRA can be revisited again in 2020
when GCC 9 is everywhere.  Until then, this patch will help users avoid
stack overrun.

This has already been fixed for arm64 for the same reason via
6e8830674ea ("arm64: kasan: Increase stack size for KASAN_EXTRA").

Link: http://lkml.kernel.org/r/20190109215209.2903-1-cai@lca.pw
Signed-off-by: Qian Cai <cai@lca.pw>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/hugetlb.c: teach follow_hugetlb_page() to handle FOLL_NOWAIT

hugetlb needs the same fix as faultin_nopage (which was applied in
commit 96312e61282a ("mm/gup.c: teach get_user_pages_unlocked to handle
FOLL_NOWAIT")) or KVM hangs because it thinks the mmap_sem was already
released by hugetlb_fault() if it returned VM_FAULT_RETRY, but it wasn't
in the FOLL_NOWAIT case.

Link: http://lkml.kernel.org/r/20190109020203.26669-2-aarcange@redhat.com
Fixes: ce53053ce378 ("kvm: switch get_user_page_nowait() to get_user_pages_unlocked()")
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Tested-by: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Reported-by: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

arch: unexport asm/shmparam.h for all architectures

Most architectures do not export shmparam.h to user-space.

  $ find arch -name shmparam.h  | sort
  arch/alpha/include/asm/shmparam.h
  arch/arc/include/asm/shmparam.h
  arch/arm64/include/asm/shmparam.h
  arch/arm/include/asm/shmparam.h
  arch/csky/include/asm/shmparam.h
  arch/ia64/include/asm/shmparam.h
  arch/mips/include/asm/shmparam.h
  arch/nds32/include/asm/shmparam.h
  arch/nios2/include/asm/shmparam.h
  arch/parisc/include/asm/shmparam.h
  arch/powerpc/include/asm/shmparam.h
  arch/s390/include/asm/shmparam.h
  arch/sh/include/asm/shmparam.h
  arch/sparc/include/asm/shmparam.h
  arch/x86/include/asm/shmparam.h
  arch/xtensa/include/asm/shmparam.h

Strangely, some users of the asm-generic wrapper export shmparam.h

  $ git grep 'generic-y += shmparam.h'
  arch/c6x/include/uapi/asm/Kbuild:generic-y += shmparam.h
  arch/h8300/include/uapi/asm/Kbuild:generic-y += shmparam.h
  arch/hexagon/include/uapi/asm/Kbuild:generic-y += shmparam.h
  arch/m68k/include/uapi/asm/Kbuild:generic-y += shmparam.h
  arch/microblaze/include/uapi/asm/Kbuild:generic-y += shmparam.h
  arch/openrisc/include/uapi/asm/Kbuild:generic-y += shmparam.h
  arch/riscv/include/asm/Kbuild:generic-y += shmparam.h
  arch/unicore32/include/uapi/asm/Kbuild:generic-y += shmparam.h

The newly added riscv correctly creates the asm-generic wrapper
in the kernel space, but the others (c6x, h8300, hexagon, m68k,
microblaze, openrisc, unicore32) create the one in the uapi directory.

Digging into the git history, now I guess fcc8487d477a ("uapi:
export all headers under uapi directories") was the misconversion.
Prior to that commit, no architecture exported to shmparam.h
As its commit description said, that commit exported shmparam.h
for c6x, h8300, hexagon, m68k, openrisc, unicore32.

83f0124ad81e ("microblaze: remove asm-generic wrapper headers")
accidentally exported shmparam.h for microblaze.

This commit unexports shmparam.h for those architectures.

There is no more reason to export include/uapi/asm-generic/shmparam.h,
so it has been moved to include/asm-generic/shmparam.h

Link: http://lkml.kernel.org/r/1546904307-11124-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stafford Horne <shorne@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Aurelien Jacquiot <jacquiot.aurelien@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Guo Ren <guoren@kernel.org>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: Mark Salter <msalter@redhat.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Vincent Chen <deanbo422@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

proc: fix /proc/net/* after setns(2)

/proc entries under /proc/net/* can't be cached into dcache because
setns(2) can change current net namespace.

[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: avoid vim miscolorization]
[adobriyan@gmail.com: write test, add dummy ->d_revalidate hook: necessary if /proc/net/* is pinned at setns time]
Link: http://lkml.kernel.org/r/20190108192350.GA12034@avx2
Link: http://lkml.kernel.org/r/20190107162336.GA9239@avx2
Fixes: 1da4d377f943fe4194ffb9fb9c26cc58fad4dd24 ("proc: revalidate misc dentries")
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Reported-by: Mateusz Stępień <mateusz.stepien@netrounds.com>
Reported-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm, memory_hotplug: don't bail out in do_migrate_range() prematurely

do_migrate_range() takes a memory range and tries to isolate the pages
to put them into a list.  This list will be later on used in
migrate_pages() to know the pages we need to migrate.

Currently, if we fail to isolate a single page, we put all already
isolated pages back to their LRU and we bail out from the function.
This is quite suboptimal, as this will force us to start over again
because scan_movable_pages will give us the same range.  If there is no
chance that we can isolate that page, we will loop here forever.

Issue debugged in [1] has proved that.  During the debugging of that
issue, it was noticed that if do_migrate_ranges() fails to isolate a
single page, we will just discard the work we have done so far and bail
out, which means that scan_movable_pages() will find again the same set
of pages.

Instead, we can just skip the error, keep isolating as much pages as
possible and then proceed with the call to migrate_pages().

This will allow us to do as much work as possible at once.

[1] https://lkml.org/lkml/2018/12/6/324

Michal said:

: I still think that this doesn't give us a whole picture.  Looping for
: ever is a bug.  Failing the isolation is quite possible and it should
: be a ephemeral condition (e.g.  a race with freeing the page or
: somebody else isolating the page for whatever reason).  And here comes
: the disadvantage of the current implementation.  We simply throw
: everything on the floor just because of a ephemeral condition.  The
: racy page_count check is quite dubious to prevent from that.

Link: http://lkml.kernel.org/r/20181211135312.27034-1-osalvador@suse.de
Signed-off-by: Oscar Salvador <osalvador@suse.de>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Dan Williams <dan.j.williams@gmail.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: William Kucharski <william.kucharski@oracle.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'for-linus' of git://git./linux/kernel/git/rdma/rdma

Pull rdma fixes from Jason Gunthorpe:
"Still not much going on, the usual set of oops and driver fixes this
  time:

   - Fix two uapi breakage regressions in mlx5 drivers

   - Various oops fixes in hfi1, mlx4, umem, uverbs, and ipoib

   - A protocol bug fix for hfi1 preventing it from implementing the
     verbs API properly, and a compatability fix for EXEC STACK user
     programs

   - Fix missed refcounting in the 'advise_mr' patches merged this
     cycle.

   - Fix wrong use of the uABI in the hns SRQ patches merged this cycle"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
  IB/uverbs: Fix OOPs in uverbs_user_mmap_disassociate
  IB/ipoib: Fix for use-after-free in ipoib_cm_tx_start
  IB/uverbs: Fix ioctl query port to consider device disassociation
  RDMA/mlx5: Fix flow creation on representors
  IB/uverbs: Fix OOPs upon device disassociation
  RDMA/umem: Add missing initialization of owning_mm
  RDMA/hns: Update the kernel header file of hns
  IB/mlx5: Fix how advise_mr() launches async work
  RDMA/device: Expose ib_device_try_get(()
  IB/hfi1: Add limit test for RC/UC send via loopback
  IB/hfi1: Remove overly conservative VM_EXEC flag check
  IB/{hfi1, qib}: Fix WC.byte_len calculation for UD_SEND_WITH_IMM
  IB/mlx4: Fix using wrong function to destroy sqp AHs under SRIOV
  RDMA/mlx5: Fix check for supported user flags when creating a QP

Merge tag 'iomap-5.0-fixes-1' of git://git./fs/xfs/xfs-linux

Pull iomap fixes from Darrick Wong:
"A couple of iomap fixes to eliminate some memory corruption and hang
  problems that were reported:

   - fix page migration when using iomap for pagecache management

   - fix a use-after-free bug in the directio code"

* tag 'iomap-5.0-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  iomap: fix a use after free in iomap_dio_rw
  iomap: get/put the page in iomap_page_create/release()

Merge tag 'pm-5.0-rc5' of git://git./linux/kernel/git/rafael/linux-pm

Pull power management fixes from Rafael Wysocki:
"These fix a PM-runtime framework regression introduced by the recent
  switch-over of device autosuspend to hrtimers and a mistake in the
  "poll idle state" code introduced by a recent change in it.

  Specifics:

   - Since ktime_get() turns out to be problematic for device
     autosuspend in the PM-runtime framework, make it use
     ktime_get_mono_fast_ns() instead (Vincent Guittot).

   - Fix an initial value of a local variable in the "poll idle state"
     code that makes it behave not exactly as expected when all idle
     states except for the "polling" one are disabled (Doug Smythies)"

* tag 'pm-5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpuidle: poll_state: Fix default time limit
  PM-runtime: Fix deadlock with ktime_get()

Merge tag 'acpi-5.0-rc5' of git://git./linux/kernel/git/rafael/linux-pm

Pull ACPI Kconfig fixes from Rafael Wysocki:
"Prevent invalid configurations from being created (e.g. by randconfig)
  due to some ACPI-related Kconfig options' dependencies that are not
  specified directly (Sinan Kaya)"

* tag 'acpi-5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  platform/x86: Fix unmet dependency warning for SAMSUNG_Q10
  platform/x86: Fix unmet dependency warning for ACPI_CMPC
  mfd: Fix unmet dependency warning for MFD_TPS68470

Merge tag 'mmc-v5.0-rc4' of git://git./linux/kernel/git/ulfh/mmc

Pull MMC host fixes from Ulf Hansson:

- mediatek: Fix incorrect register write for tunings

- bcm2835: Fixup leakage of DMA channel on probe errors

* tag 'mmc-v5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: mediatek: fix incorrect register setting of hs400_cmd_int_delay
mmc: bcm2835: Fix DMA channel leak on probe error

Merge tag 'i3c/fixes-for-5.0-rc5' of git://git./linux/kernel/git/i3c/linux

Pull i3c fixes from Boris Brezillon:

- Fix a deadlock in the designware driver

- Fix the error path in i3c_master_add_i3c_dev_locked()

* tag 'i3c/fixes-for-5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: master: dw: fix deadlock
i3c: fix missing detach if failed to retrieve i3c dev

x86/kexec: Don't setup EFI info if EFI runtime is not enabled

Kexec-ing a kernel with "efi=noruntime" on the first kernel's command
line causes the following null pointer dereference:

  BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
  #PF error: [normal kernel read fault]
  Call Trace:
   efi_runtime_map_copy+0x28/0x30
   bzImage64_load+0x688/0x872
   arch_kexec_kernel_image_load+0x6d/0x70
   kimage_file_alloc_init+0x13e/0x220
   __x64_sys_kexec_file_load+0x144/0x290
   do_syscall_64+0x55/0x1a0
   entry_SYSCALL_64_after_hwframe+0x44/0xa9

Just skip the EFI info setup if EFI runtime services are not enabled.

[ bp: Massage commit message. ]

Suggested-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Kairui Song <kasong@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Dave Young <dyoung@redhat.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: bhe@redhat.com
Cc: David Howells <dhowells@redhat.com>
Cc: erik.schmauss@intel.com
Cc: fanc.fnst@cn.fujitsu.com
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: kexec@lists.infradead.org
Cc: lenb@kernel.org
Cc: linux-acpi@vger.kernel.org
Cc: Philipp Rudo <prudo@linux.vnet.ibm.com>
Cc: rafael.j.wysocki@intel.com
Cc: robert.moore@intel.com
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Cc: Yannik Sembritzki <yannik@sembritzki.me>
Link: https://lkml.kernel.org/r/20190118111310.29589-2-kasong@redhat.com

x86: explicitly align IO accesses in memcpy_{to,from}io

In commit 170d13ca3a2f ("x86: re-introduce non-generic memcpy_{to,from}io")
I made our copy from IO space use a separate copy routine rather than
rely on the generic memcpy.  I did that because our generic memory copy
isn't actually well-defined when it comes to internal access ordering or
alignment, and will in fact depend on various CPUID flags.

In particular, the default memcpy() for a modern Intel CPU will
generally be just a "rep movsb", which works reasonably well for
medium-sized memory copies of regular RAM, since the CPU will turn it
into fairly optimized microcode.

However, for non-cached memory and IO, "rep movs" ends up being
horrendously slow and will just do the architectural "one byte at a
time" accesses implied by the movsb.

At the other end of the spectrum, if you _don't_ end up using the "rep
movsb" code, you'd likely fall back to the software copy, which does
overlapping accesses for the tail, and may copy things backwards.
Again, for regular memory that's fine, for IO memory not so much.

The thinking was that clearly nobody really cared (because things
worked), but some people had seen horrible performance due to the byte
accesses, so let's just revert back to our long ago version that dod
"rep movsl" for the bulk of the copy, and then fixed up the potentially
last few bytes of the tail with "movsw/b".

Interestingly (and perhaps not entirely surprisingly), while that was
our original memory copy implementation, and had been used before for
IO, in the meantime many new users of memcpy_*io() had come about.  And
while the access patterns for the memory copy weren't well-defined (so
arguably _any_ access pattern should work), in practice the "rep movsb"
case had been very common for the last several years.

In particular Jarkko Sakkinen reported that the memcpy_*io() change
resuled in weird errors from his Geminilake NUC TPM module.

And it turns out that the TPM TCG accesses according to spec require
that the accesses be

(a) done strictly sequentially

(b) be naturally aligned

otherwise the TPM chip will abort the PCI transaction.

And, in fact, the tpm_crb.c driver did this:

memcpy_fromio(buf, priv->rsp, 6);
...
memcpy_fromio(&buf[6], &priv->rsp[6], expected - 6);

which really should never have worked in the first place, but back
before commit 170d13ca3a2f it *happened* to work, because the
memcpy_fromio() would be expanded to a regular memcpy, and

(a) gcc would expand the first memcpy in-line, and turn it into a
     4-byte and a 2-byte read, and they happened to be in the right
     order, and the alignment was right.

(b) gcc would call "memcpy()" for the second one, and the machines that
     had this TPM chip also apparently ended up always having ERMS
     ("Enhanced REP MOVSB/STOSB instructions"), so we'd use the "rep
     movbs" for that copy.

In other words, basically by pure luck, the code happened to use the
right access sizes in the (two different!) memcpy() implementations to
make it all work.

But after commit 170d13ca3a2f, both of the memcpy_fromio() calls
resulted in a call to the routine with the consistent memory accesses,
and in both cases it started out transferring with 4-byte accesses.
Which worked for the first copy, but resulted in the second copy doing a
32-bit read at an address that was only 2-byte aligned.

Jarkko is actually fixing the fragile code in the TPM driver, but since
this is an excellent example of why we absolutely must not use a generic
memcpy for IO accesses, _and_ an IO-specific one really should strive to
align the IO accesses, let's do exactly that.

Side note: Jarkko also noted that the driver had been used on ARM
platforms, and had worked.  That was because on 32-bit ARM, memcpy_*io()
ends up always doing byte accesses, and on 64-bit ARM it first does byte
accesses to align to 8-byte boundaries, and then does 8-byte accesses
for the bulk.

So ARM actually worked by design, and the x86 case worked by pure luck.

We *might* want to make x86-64 do the 8-byte case too.  That should be a
pretty straightforward extension, but let's do one thing at a time.  And
generally MMIO accesses aren't really all that performance-critical, as
shown by the fact that for a long time we just did them a byte at a
time, and very few people ever noticed.

Reported-and-tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jerry Snitselaar <jsnitsel@redhat.com>
Cc: David Laight <David.Laight@aculab.com>
Fixes: 170d13ca3a2f ("x86: re-introduce non-generic memcpy_{to,from}io")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

apparmor: Fix aa_label_build() error handling for failed merges

aa_label_merge() can return NULL for memory allocations failures
make sure to handle and set the correct error in this case.

Reported-by: Peng Hao <peng.hao2@zte.com.cn>
Signed-off-by: John Johansen <john.johansen@canonical.com>

arm64: hibernate: Clean the __hyp_text to PoC after resume

During resume hibernate restores all physical memory. Any memory
that is accessed with the MMU disabled needs to be cleaned to the
PoC.

KVMs __hyp_text was previously ommitted as it runs with the MMU
enabled, but now that the hyp-stub is located in this section,
we must clean __hyp_text too.

This ensures secondary CPUs that come online after hibernate
has finished resuming, and load KVM via the freshly written
hyp-stub see the correct instructions.

Signed-off-by: James Morse <james.morse@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will.deacon@arm.com>

arm64: hyp-stub: Forbid kprobing of the hyp-stub

The hyp-stub is loaded by the kernel's early startup code at EL2
during boot, before KVM takes ownership later. The hyp-stub's
text is part of the regular kernel text, meaning it can be kprobed.

A breakpoint in the hyp-stub causes the CPU to spin in el2_sync_invalid.

Add it to the __hyp_text.

Signed-off-by: James Morse <james.morse@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will.deacon@arm.com>

arm64: kprobe: Always blacklist the KVM world-switch code

On systems with VHE the kernel and KVM's world-switch code run at the
same exception level. Code that is only used on a VHE system does not
need to be annotated as __hyp_text as it can reside anywhere in the
kernel text.

__hyp_text was also used to prevent kprobes from patching breakpoint
instructions into this region, as this code runs at a different
exception level. While this is no longer true with VHE, KVM still
switches VBAR_EL1, meaning a kprobe's breakpoint executed in the
world-switch code will cause a hyp-panic.

Move the __hyp_text check in the kprobes blacklist so it applies on
VHE systems too, to cover the common code and guest enter/exit
assembly.

Fixes: 888b3c8720e0 ("arm64: Treat all entry code as non-kprobe-able")
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>

arm64: kaslr: ensure randomized quantities are clean also when kaslr is off

Commit 1598ecda7b23 ("arm64: kaslr: ensure randomized quantities are
clean to the PoC") added cache maintenance to ensure that global
variables set by the kaslr init routine are not wiped clean due to
cache invalidation occurring during the second round of page table
creation.

However, if kaslr_early_init() exits early with no randomization
being applied (either due to the lack of a seed, or because the user
has disabled kaslr explicitly), no cache maintenance is performed,
leading to the same issue we attempted to fix earlier, as far as the
module_alloc_base variable is concerned.

Note that module_alloc_base cannot be initialized statically, because
that would cause it to be subject to a R_AARCH64_RELATIVE relocation,
causing it to be overwritten by the second round of KASLR relocation
processing.

Fixes: f80fb3a3d508 ("arm64: add support for kernel ASLR")
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>

arm64: Do not issue IPIs for user executable ptes

Commit 3b8c9f1cdfc5 ("arm64: IPI each CPU after invalidating the I-cache
for kernel mappings") was aimed at fixing the I-cache invalidation for
kernel mappings. However, it inadvertently caused all cache maintenance
for user mappings via set_pte_at() -> __sync_icache_dcache() ->
sync_icache_aliases() to call kick_all_cpus_sync().

Reported-by: Shijith Thotton <sthotton@marvell.com>
Tested-by: Shijith Thotton <sthotton@marvell.com>
Reported-by: Wandun Chen <chenwandun@huawei.com>
Fixes: 3b8c9f1cdfc5 ("arm64: IPI each CPU after invalidating the I-cache for kernel mappings")
Cc: <stable@vger.kernel.org> # 4.19.x-
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>

apparmor: Fix warning about unused function apparmor_ipv6_postroute

when compiled without CONFIG_IPV6:
security/apparmor/lsm.c:1601:21: warning: ‘apparmor_ipv6_postroute’ defined but not used [-Wunused-function]
static unsigned int apparmor_ipv6_postroute(void *priv,
^~~~~~~~~~~~~~~~~~~~~~~

Reported-by: Jordan Glover <Golden_Miller83@protonmail.ch>
Tested-by: Jordan Glover <Golden_Miller83@protonmail.ch>
Signed-off-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: John Johansen <john.johansen@canonical.com>

Merge branch 'acpi-misc'

* acpi-misc:
platform/x86: Fix unmet dependency warning for SAMSUNG_Q10
platform/x86: Fix unmet dependency warning for ACPI_CMPC

Merge branch 'pm-cpuidle-fixes'

* pm-cpuidle-fixes:
cpuidle: poll_state: Fix default time limit

Merge tag 'clk-fixes-for-linus' of git://git./linux/kernel/git/clk/linux

Pull clk fixes from Stephen Boyd:
"Mostly driver fixes, but there's a core framework fix in here too:

   - Revert the commits that introduce clk management for the SP clk on
     MMP2 SoCs (used for OLPC). Turns out it wasn't a good idea and
     there isn't any need to manage this clk, it just causes more
     headaches.

   - A performance regression that went unnoticed for many years where
     we would traverse the entire clk tree looking for a clk by name
     when we already have the pointer to said clk that we're looking for

   - A parent linkage fix for the qcom SDM845 clk driver

   - An i.MX clk driver rate miscalculation fix where order of
     operations were messed up

   - One error handling fix from the static checkers"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: qcom: gcc: Use active only source for CPUSS clocks
  clk: ti: Fix error handling in ti_clk_parse_divider_data()
  clk: imx: Fix fractional clock set rate computation
  clk: Remove global clk traversal on fetch parent index
  Revert "dt-bindings: marvell,mmp2: Add clock id for the SP clock"
  Revert "clk: mmp2: add SP clock"
  Revert "Input: olpc_apsp - enable the SP clock"

Merge branch 'linus' of git://git./linux/kernel/git/herbert/crypto-2.6

Pull crypto fix from Herbert Xu:
"This fixes a bug in cavium/nitrox where the callback is invoked prior
to the DMA unmap"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: cavium/nitrox - Invoke callback after DMA unmap

Merge tag 'pci-v5.0-fixes-3' of git://git./linux/kernel/git/helgaas/pci

Pull PCI fixes from Bjorn Helgaas:

- Revert armada8k GPIO reset change that broke Macchiatobin booting
   (Baruch Siach)

- Use actual size config reads on ARM cns3xxx (Koen Vandeputte)

- Fix ARM cns3xxx config write alignment issue (Koen Vandeputte)

- Fix imx6 PHY device link error checking (Leonard Crestez)

- Fix imx6 probe failure on chips without separate PCI power domain
   (Leonard Crestez)

* tag 'pci-v5.0-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  Revert "PCI: armada8k: Add support for gpio controlled reset signal"
  ARM: cns3xxx: Use actual size reads for PCIe
  ARM: cns3xxx: Fix writing to wrong PCI config registers after alignment
  PCI: imx: Fix checking pd_pcie_phy device link addition
  PCI: imx: Fix probe failure without power domain

Revert "PCI: armada8k: Add support for gpio controlled reset signal"

Revert commit 3d71746c42 ("PCI: armada8k: Add support for gpio controlled
reset signal").

That commit breaks boot on Macchiatobin board when a Mellanox NIC is
present in the PCIe slot.

It turns out that full reset cycle requires first comphy serdes
initialization. Reset signal toggle without comphy initialization makes
access to PCI configuration registers stall indefinitely. U-Boot toggles
the Macchiatobin PCIe reset line already at boot, after initializing the
comphy serdes.

So while commit 3d71746c42 ("PCI: armada8k: Add support for gpio controlled
reset signal") enables PCIe on platforms that U-Boot does not touch the
reset line (like Clearfog GT-8K), it breaks PCIe (and boot) on the
Macchiatobin board.

Revert commit 3d71746c42 ("PCI: armada8k: Add support for gpio controlled
reset signal") entirely to fix the Macchiatobin regression.

Reported-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

ARM: cns3xxx: Use actual size reads for PCIe

commit 802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config
accessors") reimplemented cns3xxx_pci_read_config() using
pci_generic_config_read32(), which preserved the property of only doing
32-bit reads.

It also replaced cns3xxx_pci_write_config() with pci_generic_config_write(),
so it changed writes from always being 32 bits to being the actual size,
which works just fine.

Given that:

- The documentation does not mention that only 32 bit access is allowed.
- Writes are already executed using the actual size
- Extensive testing shows that 8b, 16b and 32b reads work as intended

Allow read access of any size by replacing pci_generic_config_read32()
with the pci_generic_config_read() accessors.

Fixes: 802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config accessors")
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
Acked-by: Arnd Bergmann <arnd@arndb.de>
CC: Krzysztof Halasa <khalasa@piap.pl>
CC: Olof Johansson <olof@lixom.net>
CC: Robin Leblon <robin.leblon@ncentric.com>
CC: Rob Herring <robh@kernel.org>
CC: Russell King <linux@armlinux.org.uk>
CC: Tim Harvey <tharvey@gateworks.com>

ARM: cns3xxx: Fix writing to wrong PCI config registers after alignment

Originally, cns3xxx used its own functions for mapping, reading and
writing config registers.

Commit 802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config
accessors") removed the internal PCI config write function in favor of
the generic one:

  cns3xxx_pci_write_config() --> pci_generic_config_write()

cns3xxx_pci_write_config() expected aligned addresses, being produced by
cns3xxx_pci_map_bus() while the generic one pci_generic_config_write()
actually expects the real address as both the function and hardware are
capable of byte-aligned writes.

This currently leads to pci_generic_config_write() writing to the wrong
registers.

For instance, upon ath9k module loading:

- driver ath9k gets loaded
- The driver wants to write value 0xA8 to register PCI_LATENCY_TIMER,
  located at 0x0D
- cns3xxx_pci_map_bus() aligns the address to 0x0C
- pci_generic_config_write() effectively writes 0xA8 into register 0x0C
  (CACHE_LINE_SIZE)

Fix the bug by removing the alignment in the cns3xxx mapping function.

Fixes: 802b7c06adc7 ("ARM: cns3xxx: Convert PCI to use generic config accessors")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
CC: stable@vger.kernel.org # v4.0+
CC: Bjorn Helgaas <bhelgaas@google.com>
CC: Olof Johansson <olof@lixom.net>
CC: Robin Leblon <robin.leblon@ncentric.com>
CC: Rob Herring <robh@kernel.org>
CC: Russell King <linux@armlinux.org.uk>

PCI: imx: Fix checking pd_pcie_phy device link addition

The check on the device_link_add() return value is wrong;
this leads to erroneous code execution, so fix it.

Fixes: 3f7cceeab895 ("PCI: imx: Add multi-pd support")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

PCI: imx: Fix probe failure without power domain

On chips without a separate power domain for PCI (such as 6q/6qp) the
imx6_pcie_attach_pd() function incorrectly returns an error.

Fix by returning 0 if dev_pm_domain_attach_by_name() does not find
anything.

Fixes: 3f7cceeab895 ("PCI: imx: Add multi-pd support")
Reported-by: Lukas F.Hartmann <lukas@mntmn.com>
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>

gfs2: Revert "Fix loop in gfs2_rbm_find"

This reverts commit 2d29f6b96d8f80322ed2dd895bca590491c38d34.

It turns out that the fix can lead to a ~20 percent performance regression
in initial writes to the page cache according to iozone. Let's revert this
for now to have more time for a proper fix.

Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'linux-kselftest-5.0-rc5' of git://git./linux/kernel/git/shuah/linux-kselftest

Pull kselftest fixes from Shuah Khan:
"This consists of run-time fixes to cpu-hotplug, and seccomp tests,
  compile fixes to ir, net, and timers Makefiles"

* tag 'linux-kselftest-5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  selftests: timers: use LDLIBS instead of LDFLAGS
  selftests: net: use LDLIBS instead of LDFLAGS
  selftests/seccomp: Enhance per-arch ptrace syscall skip tests
  selftests: Use lirc.h from kernel tree, not from system
  selftests: cpu-hotplug: fix case where CPUs offline > CPUs present

Merge tag 'nfs-for-5.0-3' of git://git.linux-nfs.org/projects/anna/linux-nfs

Pull NFS client fixes from Anna Schumaker:
"This addresses two bugs, one in the error code handling of
  nfs_page_async_flush() and one to fix a potential NULL pointer
  dereference in nfs_parse_devname().

  Stable bugfix:
   - Fix up return value on fatal errors in nfs_page_async_flush()

  Other bugfix:
   - Fix NULL pointer dereference of dev_name"

* tag 'nfs-for-5.0-3' of git://git.linux-nfs.org/projects/anna/linux-nfs:
  NFS: Fix up return value on fatal errors in nfs_page_async_flush()
  nfs: Fix NULL pointer dereference of dev_name

Merge tag 'sound-5.0-rc5' of git://git./linux/kernel/git/tiwai/sound

Pull sound fixes from Takashi Iwai:
"Only three fixes.

  The fix for Realtek HD-audio looks lengthy, but it's just a code
  shuffling, and the actual changes are fairly small.

  The rest are a PCM core fix for a long-standing bug that was recently
  scratched by syzkaller, and a trivial USB-audio quirk for DSD support"

* tag 'sound-5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda/realtek - Fixed hp_pin no value
  ALSA: pcm: Fix tight loop of OSS capture stream
  ALSA: usb-audio: Add Opus #3 to quirks for native DSD support

x86/microcode/amd: Don't falsely trick the late loading mechanism

The load_microcode_amd() function searches for microcode patches and
attempts to apply a microcode patch if it is of different level than the
currently installed level.

While the processor won't actually load a level that is less than
what is already installed, the logic wrongly returns UCODE_NEW thus
signaling to its caller reload_store() that a late loading should be
attempted.

If the file-system contains an older microcode revision than what is
currently running, such a late microcode reload can result in these
misleading messages:

x86/CPU: CPU features have changed after loading microcode, but might not take effect.
x86/CPU: Please consider either early loading through initrd/built-in or a potential BIOS update.

These messages were issued on a system where SME/SEV are not
enabled by the BIOS (MSR C001_0010[23] = 0b) because during boot,
early_detect_mem_encrypt() is called and cleared the SME and SEV
features in this case.

However, after the wrong late load attempt, get_cpu_cap() is called and
reloads the SME and SEV feature bits, resulting in the messages.

Update the microcode level check to not attempt microcode loading if the
current level is greater than(!) and not only equal to the current patch
level.

[ bp: massage commit message. ]

Fixes: 2613f36ed965 ("x86/microcode: Attempt late loading only when new microcode is present")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/154894518427.9406.8246222496874202773.stgit@tlendack-t1.amdoffice.net

ide: ensure atapi sense request aren't preempted

There's an issue with how sense requests are handled in IDE. If ide-cd
encounters an error, it queues a sense request. With how IDE request
handling is done, this is the next request we need to handle. But it's
impossible to guarantee this, as another request could come in between
the sense being queued, and ->queue_rq() being run and handling it. If
that request ALSO fails, then we attempt to doubly queue the single
sense request we have.

Since we only support one active request at the time, defer request
processing when a sense request is queued.

Fixes: 600335205b8d "ide: convert to blk-mq"
Reported-by: He Zhe <zhe.he@windriver.com>
Tested-by: He Zhe <zhe.he@windriver.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

cifs: update internal module version number

To 2.17

Signed-off-by: Steve French <stfrench@microsoft.com>

CIFS: fix use-after-free of the lease keys

The request buffers are freed right before copying the pointers.
Use the func args instead which are identical and still valid.

Simple reproducer (requires KASAN enabled) on a cifs mount:

echo foo > foo ; tail -f foo & rm foo

Cc: <stable@vger.kernel.org> # 4.20
Fixes: 179e44d49c2f ("smb3: add tracepoint for sending lease break responses to server")
Signed-off-by: Aurelien Aptel <aaptel@suse.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Paulo Alcantara <palcantara@suse.de>

cpuidle: poll_state: Fix default time limit

The default time is declared in units of microsecnds,
but is used as nanoseconds, resulting in significant
accounting errors for idle state 0 time when all idle
states deeper than 0 are disabled.

Under these unusual conditions, we don't really care
about the poll time limit anyhow.

Fixes: 800fb34a99ce ("cpuidle: poll_state: Disregard disable idle states")
Signed-off-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

PM-runtime: Fix deadlock with ktime_get()

A deadlock has been seen when swicthing clocksources which use
PM-runtime.  The call path is:

change_clocksource
    ...
    write_seqcount_begin
    ...
    timekeeping_update
        ...
        sh_cmt_clocksource_enable
            ...
            rpm_resume
                pm_runtime_mark_last_busy
                    ktime_get
                        do
                            read_seqcount_begin
                        while read_seqcount_retry
    ....
    write_seqcount_end

Although we should be safe because we haven't yet changed the
clocksource at that time, we can't do that because of seqcount
protection.

Use ktime_get_mono_fast_ns() instead which is lock safe for such
cases.

With ktime_get_mono_fast_ns, the timestamp is not guaranteed to be
monotonic across an update and as a result can goes backward.
According to update_fast_timekeeper() description: "In the worst
case, this can result is a slightly wrong timestamp (a few
nanoseconds)". For PM-runtime autosuspend, this means only that
the suspend decision may be slightly suboptimal.

Fixes: 8234f6734c5d ("PM-runtime: Switch autosuspend over to using hrtimers")
Reported-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

fs/dcache: Track & report number of negative dentries

The current dentry number tracking code doesn't distinguish between
positive & negative dentries.  It just reports the total number of
dentries in the LRU lists.

As excessive number of negative dentries can have an impact on system
performance, it will be wise to track the number of positive and
negative dentries separately.

This patch adds tracking for the total number of negative dentries in
the system LRU lists and reports it in the 5th field in the
/proc/sys/fs/dentry-state file.  The number, however, does not include
negative dentries that are in flight but not in the LRU yet as well as
those in the shrinker lists which are on the way out anyway.

The number of positive dentries in the LRU lists can be roughly found by
subtracting the number of negative dentries from the unused count.

Matthew Wilcox had confirmed that since the introduction of the
dentry_stat structure in 2.1.60, the dummy array was there, probably for
future extension.  They were not replacements of pre-existing fields.
So no sane applications that read the value of /proc/sys/fs/dentry-state
will do dummy thing if the last 2 fields of the sysctl parameter are not
zero.  IOW, it will be safe to use one of the dummy array entry for
negative dentry count.

Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs: Don't need to put list_lru into its own cacheline

The list_lru structure is essentially just a pointer to a table of
per-node LRU lists. Even if CONFIG_MEMCG_KMEM is defined, the list
field is just used for LRU list registration and shrinker_id is set at
initialization. Those fields won't need to be touched that often.

So there is no point to make the list_lru structures to sit in their own
cachelines.

Signed-off-by: Waiman Long <longman@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/dcache: Fix incorrect nr_dentry_unused accounting in shrink_dcache_sb()

The nr_dentry_unused per-cpu counter tracks dentries in both the LRU
lists and the shrink lists where the DCACHE_LRU_LIST bit is set.

The shrink_dcache_sb() function moves dentries from the LRU list to a
shrink list and subtracts the dentry count from nr_dentry_unused. This
is incorrect as the nr_dentry_unused count will also be decremented in
shrink_dentry_list() via d_shrink_del().

To fix this double decrement, the decrement in the shrink_dcache_sb()
function is taken out.

Fixes: 4e717f5c1083 ("list_lru: remove special case function list_lru_dispose_all."
Cc: stable@kernel.org
Signed-off-by: Waiman Long <longman@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

cpu/hotplug: Fix "SMT disabled by BIOS" detection for KVM

With the following commit:

  73d5e2b47264 ("cpu/hotplug: detect SMT disabled by BIOS")

... the hotplug code attempted to detect when SMT was disabled by BIOS,
in which case it reported SMT as permanently disabled.  However, that
code broke a virt hotplug scenario, where the guest is booted with only
primary CPU threads, and a sibling is brought online later.

The problem is that there doesn't seem to be a way to reliably
distinguish between the HW "SMT disabled by BIOS" case and the virt
"sibling not yet brought online" case.  So the above-mentioned commit
was a bit misguided, as it permanently disabled SMT for both cases,
preventing future virt sibling hotplugs.

Going back and reviewing the original problems which were attempted to
be solved by that commit, when SMT was disabled in BIOS:

  1) /sys/devices/system/cpu/smt/control showed "on" instead of
     "notsupported"; and

  2) vmx_vm_init() was incorrectly showing the L1TF_MSG_SMT warning.

I'd propose that we instead consider #1 above to not actually be a
problem.  Because, at least in the virt case, it's possible that SMT
wasn't disabled by BIOS and a sibling thread could be brought online
later.  So it makes sense to just always default the smt control to "on"
to allow for that possibility (assuming cpuid indicates that the CPU
supports SMT).

The real problem is #2, which has a simple fix: change vmx_vm_init() to
query the actual current SMT state -- i.e., whether any siblings are
currently online -- instead of looking at the SMT "control" sysfs value.

So fix it by:

  a) reverting the original "fix" and its followup fix:

     73d5e2b47264 ("cpu/hotplug: detect SMT disabled by BIOS")
     bc2d8d262cba ("cpu/hotplug: Fix SMT supported evaluation")

     and

  b) changing vmx_vm_init() to query the actual current SMT state --
     instead of the sysfs control value -- to determine whether the L1TF
     warning is needed.  This also requires the 'sched_smt_present'
     variable to exported, instead of 'cpu_smt_control'.

Fixes: 73d5e2b47264 ("cpu/hotplug: detect SMT disabled by BIOS")
Reported-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Joe Mario <jmario@redhat.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: kvm@vger.kernel.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/e3a85d585da28cc333ecbc1e78ee9216e6da9396.1548794349.git.jpoimboe@redhat.com

Merge tag 'iommu-fixes-v5.0-rc4' of git://git./linux/kernel/git/joro/iommu

Pull IOMMU fixes from Joerg Roedel:
"A few more fixes this time:

   - Two patches to fix the error path of the map_sg implementation of
     the AMD IOMMU driver.

   - Also a missing IOTLB flush is fixed in the AMD IOMMU driver.

   - Memory leak fix for the Intel IOMMU driver.

   - Fix a regression in the Mediatek IOMMU driver which caused device
     initialization to fail (seen as broken HDMI output)"

* tag 'iommu-fixes-v5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/amd: Fix IOMMU page flush when detach device from a domain
  iommu/mediatek: Use correct fwspec in mtk_iommu_add_device()
  iommu/vt-d: Fix memory leak in intel_iommu_put_resv_regions()
  iommu/amd: Unmap all mapped pages in error path of map_sg
  iommu/amd: Call free_iova_fast with pfn in map_sg

Merge tag 'gpio-v5.0-3' of git://git./linux/kernel/git/linusw/linux-gpio

Pull GPIO fixes from Linus Walleij:
"Here is a bunch of GPIO fixes for the v5.0 series. I was helped out by
  Bartosz in collecting these fixes, for which I am very grateful, the
  biggest achievement in GPIO right now is work distribution.

  There is one serious core fix (timestamping) and a bunch of driver
  fixes:

   - Fix timestamps on nested IRQs

   - Handle IRQs properly in multiple instances of PCF857x

   - Use the right data register and IRQ type setting in the Spreadtrum
     GPIO driver

   - Let the value argument work properly when setting direction in the
     Altera GPIO driver

   - Mask interrupts properly in the vf610 driver"

* tag 'gpio-v5.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: vf610: Mask all GPIO interrupts
  gpio: altera-a10sr: Set proper output level for direction_output
  gpio: sprd: Fix incorrect irq type setting for the async EIC
  gpio: sprd: Fix the incorrect data register
  gpiolib: fix line event timestamps for nested irqs
  gpio: pcf857x: Fix interrupts on multiple instances

btrfs: On error always free subvol_name in btrfs_mount

The subvol_name is allocated in btrfs_parse_subvol_options and is
consumed and freed in mount_subvol. Add a free to the error paths that
don't call mount_subvol so that it is guaranteed that subvol_name is
freed when an error happens.

Fixes: 312c89fbca06 ("btrfs: cleanup btrfs_mount() using btrfs_mount_root()")
Cc: stable@vger.kernel.org # v4.19+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>

btrfs: clean up pending block groups when transaction commit aborts

The fstests generic/475 stresses transaction aborts and can reveal
space accounting or use-after-free bugs regarding block goups.

In this case the pending block groups that remain linked to the
structures after transaction commit aborts in the middle.

The corrupted slabs lead to failures in following tests, eg. generic/476

  [ 8172.752887] BUG: unable to handle kernel NULL pointer dereference at 0000000000000058
  [ 8172.755799] #PF error: [normal kernel read fault]
  [ 8172.757571] PGD 661ae067 P4D 661ae067 PUD 3db8e067 PMD 0
  [ 8172.759000] Oops: 0000 [#1] PREEMPT SMP
  [ 8172.760209] CPU: 0 PID: 39 Comm: kswapd0 Tainted: G        W         5.0.0-rc2-default #408
  [ 8172.762495] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.11.2-0-gf9626cc-prebuilt.qemu-project.org 04/01/2014
  [ 8172.765772] RIP: 0010:shrink_page_list+0x2f9/0xe90
  [ 8172.770453] RSP: 0018:ffff967f00663b18 EFLAGS: 00010287
  [ 8172.771184] RAX: 0000000000000000 RBX: ffff967f00663c20 RCX: 0000000000000000
  [ 8172.772850] RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffff8c0620ab20e0
  [ 8172.774629] RBP: ffff967f00663dd8 R08: 0000000000000000 R09: 0000000000000000
  [ 8172.776094] R10: ffff8c0620ab22f8 R11: ffff8c063f772688 R12: ffff967f00663b78
  [ 8172.777533] R13: ffff8c063f625600 R14: ffff8c063f625608 R15: dead000000000200
  [ 8172.778886] FS:  0000000000000000(0000) GS:ffff8c063d400000(0000) knlGS:0000000000000000
  [ 8172.780545] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  [ 8172.781787] CR2: 0000000000000058 CR3: 000000004e962000 CR4: 00000000000006f0
  [ 8172.783547] Call Trace:
  [ 8172.784112]  shrink_inactive_list+0x194/0x410
  [ 8172.784747]  shrink_node_memcg.constprop.85+0x3a5/0x6a0
  [ 8172.785472]  shrink_node+0x62/0x1e0
  [ 8172.786011]  balance_pgdat+0x216/0x460
  [ 8172.786577]  kswapd+0xe3/0x4a0
  [ 8172.787085]  ? finish_wait+0x80/0x80
  [ 8172.787795]  ? balance_pgdat+0x460/0x460
  [ 8172.788799]  kthread+0x116/0x130
  [ 8172.789640]  ? kthread_create_on_node+0x60/0x60
  [ 8172.790323]  ret_from_fork+0x24/0x30
  [ 8172.794253] CR2: 0000000000000058

or accounting errors at umount time:

  [ 8159.537251] WARNING: CPU: 2 PID: 19031 at fs/btrfs/extent-tree.c:5987 btrfs_free_block_groups+0x3d5/0x410 [btrfs]
  [ 8159.543325] CPU: 2 PID: 19031 Comm: umount Tainted: G        W         5.0.0-rc2-default #408
  [ 8159.545472] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.11.2-0-gf9626cc-prebuilt.qemu-project.org 04/01/2014
  [ 8159.548155] RIP: 0010:btrfs_free_block_groups+0x3d5/0x410 [btrfs]
  [ 8159.554030] RSP: 0018:ffff967f079cbde8 EFLAGS: 00010206
  [ 8159.555144] RAX: 0000000001000000 RBX: ffff8c06366cf800 RCX: 0000000000000000
  [ 8159.556730] RDX: 0000000000000002 RSI: 0000000000000001 RDI: ffff8c06255ad800
  [ 8159.558279] RBP: ffff8c0637ac0000 R08: 0000000000000001 R09: 0000000000000000
  [ 8159.559797] R10: 0000000000000000 R11: 0000000000000001 R12: ffff8c0637ac0108
  [ 8159.561296] R13: ffff8c0637ac0158 R14: 0000000000000000 R15: dead000000000100
  [ 8159.562852] FS:  00007f7f693b9fc0(0000) GS:ffff8c063d800000(0000) knlGS:0000000000000000
  [ 8159.564839] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  [ 8159.566160] CR2: 00007f7f68fab7b0 CR3: 000000000aec7000 CR4: 00000000000006e0
  [ 8159.567898] Call Trace:
  [ 8159.568597]  close_ctree+0x17f/0x350 [btrfs]
  [ 8159.569628]  generic_shutdown_super+0x64/0x100
  [ 8159.570808]  kill_anon_super+0x14/0x30
  [ 8159.571857]  btrfs_kill_super+0x12/0xa0 [btrfs]
  [ 8159.573063]  deactivate_locked_super+0x29/0x60
  [ 8159.574234]  cleanup_mnt+0x3b/0x70
  [ 8159.575176]  task_work_run+0x98/0xc0
  [ 8159.576177]  exit_to_usermode_loop+0x83/0x90
  [ 8159.577315]  do_syscall_64+0x15b/0x180
  [ 8159.578339]  entry_SYSCALL_64_after_hwframe+0x49/0xbe

This fix is based on 2 Josef's patches that used sideefects of
btrfs_create_pending_block_groups, this fix introduces the helper that
does what we need.

CC: stable@vger.kernel.org # 4.4+
CC: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>

btrfs: fix potential oops in device_list_add

alloc_fs_devices() can return ERR_PTR(-ENOMEM), so dereferencing its
result before the check for IS_ERR() is a bad idea.

Fixes: d1a63002829a4 ("btrfs: add members to fs_devices to track fsid changes")
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>

blk-mq: fix a hung issue when fsync

Florian reported a io hung issue when fsync(). It should be
triggered by following race condition.

data + post flush         a flush

blk_flush_complete_seq
  case REQ_FSEQ_DATA
    blk_flush_queue_rq
    issued to driver      blk_mq_dispatch_rq_list
                            try to issue a flush req
                            failed due to NON-NCQ command
                            .queue_rq return BLK_STS_DEV_RESOURCE

request completion
  req->end_io // doesn't check RESTART
  mq_flush_data_end_io
    case REQ_FSEQ_POSTFLUSH
      blk_kick_flush
        do nothing because previous flush
        has not been completed
     blk_mq_run_hw_queue
                              insert rq to hctx->dispatch
                              due to RESTART is still set, do nothing

To fix this, replace the blk_mq_run_hw_queue in mq_flush_data_end_io
with blk_mq_sched_restart to check and clear the RESTART flag.

Fixes: bd166ef1 (blk-mq-sched: add framework for MQ capable IO schedulers)
Reported-by: Florian Stecker <m19@florianstecker.de>
Tested-by: Florian Stecker <m19@florianstecker.de>
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

block: pass no-op callback to INIT_WORK().

syzbot is hitting flush_work() warning caused by commit 4d43d395fed12463
("workqueue: Try to catch flush_work() without INIT_WORK().") [1].
Although that commit did not expect INIT_WORK(NULL) case, calling
flush_work() without setting a valid callback should be avoided anyway.
Fix this problem by setting a no-op callback instead of NULL.

[1] https://syzkaller.appspot.com/bug?id=e390366bc48bc82a7c668326e0663be3b91cbd29

Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-and-tested-by: syzbot <syzbot+ba2a929dcf8e704c180e@syzkaller.appspotmail.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

MAINTAINERS: Add Andy and Darren as arch/x86/platform/ reviewers

... so that they can get CCed on platform patches.

Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Andy Shevchenko <andy@infradead.org>
Cc: x86@kernel.org
Link: https://lkml.kernel.org/r/20190128113619.19025-1-bp@alien8.de

Merge git://git./linux/kernel/git/davem/net

Pull networking fixes from David Miller:

1) Need to save away the IV across tls async operations, from Dave
    Watson.

2) Upon successful packet processing, we should liberate the SKB with
    dev_consume_skb{_irq}(). From Yang Wei.

3) Only apply RX hang workaround on effected macb chips, from Harini
    Katakam.

4) Dummy netdev need a proper namespace assigned to them, from Josh
    Elsasser.

5) Some paths of nft_compat run lockless now, and thus we need to use a
    proper refcnt_t. From Florian Westphal.

6) Avoid deadlock in mlx5 by doing IRQ locking, from Moni Shoua.

7) netrom does not refcount sockets properly wrt. timers, fix that by
    using the sock timer API. From Cong Wang.

8) Fix locking of inexact inserts of xfrm policies, from Florian
    Westphal.

9) Missing xfrm hash generation bump, also from Florian.

10) Missing of_node_put() in hns driver, from Yonglong Liu.

11) Fix DN_IFREQ_SIZE, from Johannes Berg.

12) ip6mr notifier is invoked during traversal of wrong table, from Nir
    Dotan.

13) TX promisc settings not performed correctly in qed, from Manish
    Chopra.

14) Fix OOB access in vhost, from Jason Wang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
  MAINTAINERS: Add entry for XDP (eXpress Data Path)
  net: set default network namespace in init_dummy_netdev()
  net: b44: replace dev_kfree_skb_xxx by dev_consume_skb_xxx for drop profiles
  net: caif: call dev_consume_skb_any when skb xmit done
  net: 8139cp: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
  net: macb: Apply RXUBR workaround only to versions with errata
  net: ti: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
  net: apple: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
  net: amd8111e: replace dev_kfree_skb_irq by dev_consume_skb_irq
  net: alteon: replace dev_kfree_skb_irq by dev_consume_skb_irq
  net: tls: Fix deadlock in free_resources tx
  net: tls: Save iv in tls_rec for async crypto requests
  vhost: fix OOB in get_rx_bufs()
  qed: Fix stack out of bounds bug
  qed: Fix system crash in ll2 xmit
  qed: Fix VF probe failure while FLR
  qed: Fix LACP pdu drops for VFs
  qed: Fix bug in tx promiscuous mode settings
  net: i825xx: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
  netfilter: ipt_CLUSTERIP: fix warning unused variable cn
  ...

CIFS: Do not consider -ENODATA as stat failure for reads

When doing reads beyound the end of a file the server returns
error STATUS_END_OF_FILE error which is mapped to -ENODATA.
Currently we report it as a failure which confuses read stats.
Change it to not consider -ENODATA as failure for stat purposes.

Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org>

CIFS: Do not count -ENODATA as failure for query directory

Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org>

CIFS: Fix trace command logging for SMB2 reads and writes

Currently we log success once we send an async IO request to
the server. Instead we need to analyse a response and then log
success or failure for a particular command. Also fix argument
list for read logging.

Cc: <stable@vger.kernel.org> # 4.18
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>

CIFS: Fix possible oops and memory leaks in async IO

Allocation of a page array for non-cached IO was separated from
allocation of rdata and wdata structures and this introduced memory
leaks and a possible null pointer dereference. This patch fixes
these problems.

Cc: <stable@vger.kernel.org>
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>

cifs: limit amount of data we request for xattrs to CIFSMaxBufSize

minus the various headers and blobs that will be part of the reply.

or else we might trigger a session reconnect.

Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>

cifs: fix computation for MAX_SMB2_HDR_SIZE

The size of the fixed part of the create response is 88 bytes not 56.

Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>

NFS: Fix up return value on fatal errors in nfs_page_async_flush()

Ensure that we return the fatal error value that caused us to exit
nfs_page_async_flush().

Fixes: c373fff7bd25 ("NFSv4: Don't special case "launder"")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: stable@vger.kernel.org # v4.12+
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>

x86/speculation: Remove redundant arch_smt_update() invocation

With commit a74cfffb03b7 ("x86/speculation: Rework SMT state change"),
arch_smt_update() is invoked from each individual CPU hotplug function.

Therefore the extra arch_smt_update() call in the sysfs SMT control is
redundant.

Fixes: a74cfffb03b7 ("x86/speculation: Rework SMT state change")
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <konrad.wilk@oracle.com>
Cc: <dwmw@amazon.co.uk>
Cc: <bp@suse.de>
Cc: <srinivas.eeda@oracle.com>
Cc: <peterz@infradead.org>
Cc: <hpa@zytor.com>
Link: https://lkml.kernel.org/r/e2e064f2-e8ef-42ca-bf4f-76b612964752@default

x86/fault: Fix sign-extend unintended sign extension

show_ldttss() shifts desc.base2 by 24 bit, but base2 is 8 bits of a
bitfield in a u16.

Due to the really great idea of integer promotion in C99 base2 is promoted
to an int, because that's the standard defined behaviour when all values
which can be represented by base2 fit into an int.

Now if bit 7 is set in desc.base2 the result of the shift left by 24 makes
the resulting integer negative and the following conversion to unsigned
long legitmately sign extends first causing the upper bits 32 bits to be
set in the result.

Fix this by casting desc.base2 to unsigned long before the shift.

Detected by CoverityScan, CID#1475635 ("Unintended sign extension")

[ tglx: Reworded the changelog a bit as I actually had to lookup
the standard (again) to decode the original one. ]

Fixes: a1a371c468f7 ("x86/fault: Decode page fault OOPSes better")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: kernel-janitors@vger.kernel.org
Link: https://lkml.kernel.org/r/20181222191116.21831-1-colin.king@canonical.com