Viresh Kumar [Tue, 17 Apr 2012 11:38:50 +0000 (17:08 +0530)]
USB: ehci: ohci: Add clk_{un}prepare() support
clk_{un}prepare is mandatory for platforms using common clock framework. Since
these drivers are used by SPEAr platform, which supports common clock framework,
add clk_{un}prepare() support for them.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adhir Ramjiawan [Mon, 9 Apr 2012 12:01:38 +0000 (14:01 +0200)]
USB: serial: removed assignment from if statements in ti_usb_3410_5052.c
Removed the assignment statements found in if statements by the
checkpatch.pl tool.
Signed-off-by: Adhir Ramjiawan <adhirramjiawan0@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Masanari Iida [Wed, 18 Apr 2012 15:04:46 +0000 (00:04 +0900)]
usb: Fix various typo within usb
Correct spelling typo within usb
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Tue, 17 Apr 2012 19:23:25 +0000 (15:23 -0400)]
EHCI: don't try to clear the IAAD bit
This patch (as1541) corrects a small mistake in ehci-hcd. The IAAD
(Interrupt on Async Advance Doorbell) bit in the USBCMD register is
designed, as its name says, to act as a "doorbell". That is, the
driver activates the bit by setting it to 1, and the hardware
deactivates it later by setting it back to 0. The driver cannot clear
the bit by writing a 0 to it; such writes are simply ignored.
Therefore there is no reason for ehci-hcd to try to clear the bit.
The patch removes the two instances where such attempts occur.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stefan Roese [Mon, 16 Apr 2012 03:38:08 +0000 (09:08 +0530)]
USB: Add DT probing support to ehci-spear and ohci-spear
This patch adds support to configure the SPEAr EHCI & OHCI driver via
device-tree instead of platform_data.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jingoo Han [Fri, 13 Apr 2012 02:06:36 +0000 (11:06 +0900)]
USB: ehci-s5p: add clock gating to suspend/resume
This patch adds clock gating to suspend and resume functions.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nobuhiro Iwamatsu [Thu, 12 Apr 2012 06:48:49 +0000 (15:48 +0900)]
usb: ehci-sh: Add PHY init function with platform data
In devices using ehci-sh, initialization of the PHY may be necessary.
This adds platform data to ehci-sh and provide function to initialize PHY.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Shimoda, Yoshihiro <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jesper Juhl [Mon, 9 Apr 2012 20:52:26 +0000 (22:52 +0200)]
usb/atm/ueagle-atm: Don't test for NULL ptr before calling release_firmware()
release_firmware() deals gracefullt w/ NULL pointers, no need to check
first.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jesper Juhl [Mon, 9 Apr 2012 20:52:04 +0000 (22:52 +0200)]
usb/storage/ene_ub6250: Remove redundant NULL check before release_firmware() and pointless assignment
release_firmware() tests for a NULL pointer, so it's redundant to do
that checking before calling it.
Additionally, in ene_load_bincode(), 'sd_fw' is a local variable so
setting it to NULL just before it goes out of scope is completely
pointless, so remove that assignment.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Venu Byravarasu [Fri, 6 Apr 2012 04:10:18 +0000 (09:40 +0530)]
usb: host: tegra: re-arranging ehci functions
Re-arranged EHCI generic and tegra specific functions
into two separate groups for more readability.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Grzeschik [Thu, 5 Apr 2012 12:56:10 +0000 (14:56 +0200)]
isp1760-hcd: fix possible memory leak if urb could not be enqueued
After packetize_urb was called, we could still run into an error path
and will not hand over the prepared qtd to the qtd_list. Make sure to
free the prepared qtd in that case to avoid memory leaks.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Grzeschik [Wed, 18 Apr 2012 07:58:23 +0000 (09:58 +0200)]
isp1760-hcd: move dequeued qtds to the front in qh
Make sure that dequeued urbs get handled first
by collect_qtds. To achieve that we better move them
up to the head in the qh list.
This for instance fixes hanging serial devices, which wait
for dequeued urbs to properly close their device node.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Grzeschik [Thu, 5 Apr 2012 12:56:08 +0000 (14:56 +0200)]
isp1760-hcd: don't confuse parsers on kmem_cache_create
If DEBUG is defined, the kmem_cache_create call a
WARN_ON if the name of the cache uses a space.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Grzeschik [Thu, 5 Apr 2012 12:56:07 +0000 (14:56 +0200)]
isp1760-if: make module unloads correctly
Without this patch, the prepared disable routines
will not be called on module unloading.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ramneek Mehresh [Tue, 20 Mar 2012 05:05:50 +0000 (10:35 +0530)]
fsl/usb: Add controller version based ULPI and UTMI phy support
Add support for ULPI and UTMI PHYs based on usb controller
version info read from device-tree
Example of USB Controller versioning info:
Version 1.2 and below : MPC8536, MPC8315, etc
Version 1.6 : P1020, P1010, P2020, P5020, etc
Version 2.2 : PSC9131, PSC9132, P3060, etc
No changes for non-DT users
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Mon, 26 Mar 2012 19:01:50 +0000 (21:01 +0200)]
USB: add EOPNOTSUPP to usb_translate_errors
Allow drivers to return EOPNOTSUPP to user space even when filtered
through usb_translate_errors.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Chen [Thu, 29 Mar 2012 01:50:06 +0000 (09:50 +0800)]
USB: EHCI: remove wrong debug message for port speed
It displays wrong debug message if we plug in a full/low
speed device at port for builtin TT controller. We can get
device/port speed information at following code of hub_port_init,
so it is better to replace it with debug message of "reset complete".
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Venu Byravarasu [Thu, 5 Apr 2012 05:55:30 +0000 (11:25 +0530)]
usb: host: tegra: code clean up
With this patch:
1. Renamed structure and function names to be more meaningful.
2. Removed unnecessary local variables.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hauke Mehrtens [Thu, 15 Mar 2012 22:49:59 +0000 (23:49 +0100)]
USB: OHCI: remove old SSB OHCI driver
This is now replaced by the new ssb USB driver, which also supports
devices with an EHCI controller.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hauke Mehrtens [Thu, 15 Mar 2012 22:49:58 +0000 (23:49 +0100)]
USB: Add driver for the ssb bus
This adds a USB driver using the generic platform device driver for the
USB controller found on the Broadcom ssb bus. The ssb bus just
exposes one device which serves the OHCI and the EHCI controller at the
same time. This driver probes for this USB controller and creates and
registers two new platform devices which will be probed by the new
generic platform device driver. This makes it possible to use the EHCI
and the OCHI controller on the ssb bus at the same time.
The old ssb OHCI USB driver will be removed in the next step as this
driver also provide an OHCI driver and an EHCI for the cores supporting
it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hauke Mehrtens [Thu, 15 Mar 2012 22:49:57 +0000 (23:49 +0100)]
USB: Add driver for the bcma bus
This adds a USB driver using the generic platform device driver for the
USB controller found on the Broadcom bcma bus. The bcma bus just
exposes one device which serves the OHCI and the EHCI controller at the
same time. This driver probes for this USB controller and creates and
registers two new platform devices which will be probed by the new
generic platform device driver. This makes it possible to use the EHCI
and the OCHI controller on the bcma bus at the same time.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hauke Mehrtens [Thu, 15 Mar 2012 22:49:56 +0000 (23:49 +0100)]
bcma: scan for extra address space
Some cores like the USB core have two address spaces. In the USB host
controller one address space is used for the OHCI and the other for the
EHCI controller interface. The USB controller is the only core I found
with two address spaces. This code is based on the AI scan function
ai_scan() in shared/aiutils.c in the Broadcom SDK.
CC: Rafał Miłecki <zajec5@gmail.com>
CC: linux-wireless@vger.kernel.org
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Mon, 26 Mar 2012 18:31:38 +0000 (20:31 +0200)]
USB: io_ti: fix abuse of interface data
Fix abuse of interface data which was used to signal device disconnect.
Use the usb_serial disconnect flag and mutex where appropriate.
Note that there's no need to grab the mutex in chase_port as it does not
access the device.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 22 Mar 2012 15:50:55 +0000 (16:50 +0100)]
USB: whiteheat: reimplement using generic framework
Kill custom list-based read and write implementations and reimplement
using the generic framework.
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 22 Mar 2012 15:50:54 +0000 (16:50 +0100)]
USB: whiteheat: remove driver version
Remove driver version -- it's the kernel version that matters.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aleksey Babahin [Mon, 19 Mar 2012 20:46:37 +0000 (00:46 +0400)]
USB: serial: metro-usb: cosmetic fix in driver description.
Message in kernel log:
"metro-usb ttyUSB0: Metrologic USB to Serial converter now disconnected from ttyUSB0"
bit more likely than:
"metro-usb ttyUSB0: Metrologic USB to serial converter. converter now disconnected from ttyUSB0"
Signed-off-by: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aleksey Babahin [Mon, 19 Mar 2012 20:46:36 +0000 (00:46 +0400)]
USB: serial: metro-usb: remove duplicated #include <linux/errno.h>
Signed-off-by: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aleksey Babahin [Mon, 19 Mar 2012 20:46:35 +0000 (00:46 +0400)]
USB: serial: metro-usb: make debug messages bit more informative.
In this place result value is always zero. Use urb->status instead.
Signed-off-by: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aleksey Babahin [Mon, 19 Mar 2012 20:46:34 +0000 (00:46 +0400)]
USB: serial: metro-usb: print errors always, not only in debug mode.
Signed-off-by: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aleksey Babahin [Mon, 19 Mar 2012 20:46:33 +0000 (00:46 +0400)]
USB: serial: metro-usb: get data from device in Uni-Directional mode.
We should send special control command to tell device start or stop
transmitting a data.
In Bi-Directional mode that cmd`s are not required.
Signed-off-by: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aleksey Babahin [Mon, 19 Mar 2012 20:46:32 +0000 (00:46 +0400)]
USB: serial: metro-usb: dummy implement write_int_callback() function.
This function is never called now. Because we don`t send much data
to the device, only one byte via usb_interrupt_msg(). That doesn't require
callback function. But without declaration of write_int_callback inside
the struct usb_serial_driver, the usb_serial_probe doesn't initialize
endpoint address for the interrupt out pipe(interrupt_out_endpointAddress).
This endpoint is necessary for sending data via usb_interrupt_msg()
function.
Signed-off-by: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aleksey Babahin [Mon, 19 Mar 2012 20:46:31 +0000 (00:46 +0400)]
USB: serial: metro-usb: Fix idProduct for Uni-Directional mode.
The right idProduct for Metrologic Bar Code Scanner
in Uni-Directional Serial Emulation mode is 0x0700.
Also rename idProduct for Bi-Directional mode to be a bit more informative.
Signed-off-by: Aleksey Babahin <tamerlan311@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sun, 8 Apr 2012 01:30:41 +0000 (18:30 -0700)]
Linux 3.4-rc2
Linus Torvalds [Sat, 7 Apr 2012 16:56:00 +0000 (09:56 -0700)]
Merge tag 'regmap-3.4-fixes' of git://git./linux/kernel/git/broonie/regmap
Pull two more small regmap fixes from Mark Brown:
- Now we have users for it that aren't running Android it turns out
that regcache_sync_region() is much more useful to drivers if it's
exported for use by modules. Who knew?
- Make sure we don't divide by zero when doing debugfs dumps of
rbtrees, not visible up until now because everything was providing at
least some cache on startup.
* tag 'regmap-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: prevent division by zero in rbtree_show
regmap: Export regcache_sync_region()
Linus Torvalds [Sat, 7 Apr 2012 16:53:33 +0000 (09:53 -0700)]
Merge branch 'kvm-updates/3.4' of git://git./virt/kvm/kvm
Pull a few KVM fixes from Avi Kivity:
"A bunch of powerpc KVM fixes, a guest and a host RCU fix (unrelated),
and a small build fix."
* 'kvm-updates/3.4' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Resolve RCU vs. async page fault problem
KVM: VMX: vmx_set_cr0 expects kvm->srcu locked
KVM: PMU: Fix integer constant is too large warning in kvm_pmu_set_msr()
KVM: PPC: Book3S: PR: Fix preemption
KVM: PPC: Save/Restore CR over vcpu_run
KVM: PPC: Book3S HV: Save and restore CR in __kvmppc_vcore_entry
KVM: PPC: Book3S HV: Fix kvm_alloc_linear in case where no linears exist
KVM: PPC: Book3S: Compile fix for ppc32 in HIOR access code
Linus Torvalds [Sat, 7 Apr 2012 16:52:46 +0000 (09:52 -0700)]
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
Pull SuperH fixes from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh: fix clock-sh7757 for the latest sh_mobile_sdhi driver
serial: sh-sci: use serial_port_in/out vs sci_in/out.
sh: vsyscall: Fix up .eh_frame generation.
sh: dma: Fix up device attribute mismatch from sysdev fallout.
sh: dwarf unwinder depends on SHcompact.
sh: fix up fallout from system.h disintegration.
Linus Torvalds [Sat, 7 Apr 2012 16:51:36 +0000 (09:51 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jmorris/linux-security
Pull security layer fixlet from James Morris.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
sysctl: fix write access to dmesg_restrict/kptr_restrict
Linus Torvalds [Sat, 7 Apr 2012 02:56:04 +0000 (19:56 -0700)]
Merge branch 'release' of git://git./linux/kernel/git/lenb/linux
Pull ACPI & Power Management patches from Len Brown:
"Two fixes for cpuidle merge-window changes, plus a URL fix in
MAINTAINERS"
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
MAINTAINERS: Update git url for ACPI
cpuidle: Fix panic in CPU off-lining with no idle driver
ACPI processor: Use safe_halt() rather than halt() in acpi_idle_play_dead()
Linus Torvalds [Sat, 7 Apr 2012 02:54:26 +0000 (19:54 -0700)]
Merge branch '3.4-rc-fixes' of git://git./linux/kernel/git/nab/target-pending
Pull target fixes from Nicholas Bellinger:
"Pull two tcm_fc fabric related fixes for -rc2:
Note that both have been CC'ed to stable, and patch #1 is the
important one that addresses a memory corruption bug related to FC
exchange timeouts + command abort.
Thanks again to MDR for tracking down this issue!"
* '3.4-rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
tcm_fc: Do not free tpg structure during wq allocation failure
tcm_fc: Add abort flag for gracefully handling exchange timeout
Mark Rustad [Tue, 3 Apr 2012 17:24:52 +0000 (10:24 -0700)]
tcm_fc: Do not free tpg structure during wq allocation failure
Avoid freeing a registered tpg structure if an alloc_workqueue call
fails. This fixes a bug where the failure was leaking memory associated
with se_portal_group setup during the original core_tpg_register() call.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Acked-by: Kiran Patil <Kiran.patil@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Mark Rustad [Tue, 3 Apr 2012 17:24:41 +0000 (10:24 -0700)]
tcm_fc: Add abort flag for gracefully handling exchange timeout
Add abort flag and use it to terminate processing when an exchange
is timed out or is reset. The abort flag is used in place of the
transport_generic_free_cmd function call in the reset and timeout
cases, because calling that function in that context would free
memory that was in use. The aborted flag allows the lifetime to
be managed in a more normal way, while truncating the processing.
This change eliminates a source of memory corruption which
manifested in a variety of ugly ways.
(nab: Drop unused struct fc_exch *ep in ft_recv_seq)
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Acked-by: Kiran Patil <Kiran.patil@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Len Brown [Sat, 7 Apr 2012 01:48:59 +0000 (21:48 -0400)]
Merge branches 'idle-fix' and 'misc' into release
Igor Murzov [Fri, 30 Mar 2012 18:40:12 +0000 (22:40 +0400)]
MAINTAINERS: Update git url for ACPI
Signed-off-by: Igor Murzov <e-mail@date.by>
Signed-off-by: Len Brown <len.brown@intel.com>
Linus Torvalds [Sat, 7 Apr 2012 00:56:20 +0000 (17:56 -0700)]
Merge branch 'stable' of git://git./linux/kernel/git/cmetcalf/linux-tile
Pull arch/tile bug fixes from Chris Metcalf:
"This includes Paul Gortmaker's change to fix the <asm/system.h>
disintegration issues on tile, a fix to unbreak the tilepro ethernet
driver, and a backlog of bugfix-only changes from internal Tilera
development over the last few months.
They have all been to LKML and on linux-next for the last few days.
The EDAC change to MAINTAINERS is an oddity but discussion on the
linux-edac list suggested I ask you to pull that change through my
tree since they don't have a tree to pull edac changes from at the
moment."
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile: (39 commits)
drivers/net/ethernet/tile: fix netdev_alloc_skb() bombing
MAINTAINERS: update EDAC information
tilepro ethernet driver: fix a few minor issues
tile-srom.c driver: minor code cleanup
edac: say "TILEGx" not "TILEPro" for the tilegx edac driver
arch/tile: avoid accidentally unmasking NMI-type interrupt accidentally
arch/tile: remove bogus performance optimization
arch/tile: return SIGBUS for addresses that are unaligned AND invalid
arch/tile: fix finv_buffer_remote() for tilegx
arch/tile: use atomic exchange in arch_write_unlock()
arch/tile: stop mentioning the "kvm" subdirectory
arch/tile: export the page_home() function.
arch/tile: fix pointer cast in cacheflush.c
arch/tile: fix single-stepping over swint1 instructions on tilegx
arch/tile: implement panic_smp_self_stop()
arch/tile: add "nop" after "nap" to help GX idle power draw
arch/tile: use proper memparse() for "maxmem" options
arch/tile: fix up locking in pgtable.c slightly
arch/tile: don't leak kernel memory when we unload modules
arch/tile: fix bug in delay_backoff()
...
Linus Torvalds [Sat, 7 Apr 2012 00:54:53 +0000 (17:54 -0700)]
Merge tag 'stable/for-linus-3.4-rc1-tag' of git://git./linux/kernel/git/konrad/xen
Pull xen fixes from Konrad Rzeszutek Wilk:
"Two fixes for regressions:
* one is a workaround that will be removed in v3.5 with proper fix in
the tip/x86 tree,
* the other is to fix drivers to load on PV (a previous patch made
them only load in PVonHVM mode).
The rest are just minor fixes in the various drivers and some cleanup
in the core code."
* tag 'stable/for-linus-3.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pcifront: avoid pci_frontend_enable_msix() falsely returning success
xen/pciback: fix XEN_PCI_OP_enable_msix result
xen/smp: Remove unnecessary call to smp_processor_id()
xen/x86: Workaround 'x86/ioapic: Add register level checks to detect bogus io-apic entries'
xen: only check xen_platform_pci_unplug if hvm
Linus Torvalds [Sat, 7 Apr 2012 00:22:23 +0000 (17:22 -0700)]
Merge tag 'mmc-fixes-for-3.4-rc2' of git://git./linux/kernel/git/cjb/mmc
Pull MMC fixes from Chris Ball:
- Disable use of MSI in sdhci-pci, which caused multiple chipsets to
stop working in 3.4-rc1. I'll wait to turn this on again until we
have a chipset whitelist for it.
- Fix a libertas SDIO powered-resume regression introduced in 3.3;
thanks to Neil Brown and Rafael Wysocki for this fix.
- Fix module reloading on omap_hsmmc.
- Stop trusting the spec/card's specified maximum data timeout length,
and use three seconds instead. Previously we used 300ms.
Also cleanups and fixes for s3c, atmel, sh_mmcif and omap_hsmmc.
* tag 'mmc-fixes-for-3.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (28 commits)
mmc: use really long write timeout to deal with crappy cards
mmc: sdhci-dove: Fix compile error by including module.h
mmc: Prevent 1.8V switch for SD hosts that don't support UHS modes.
Revert "mmc: sdhci-pci: Add MSI support"
Revert "mmc: sdhci-pci: add quirks for broken MSI on O2Micro controllers"
mmc: core: fix power class selection
mmc: omap_hsmmc: fix module re-insertion
mmc: omap_hsmmc: convert to module_platform_driver
mmc: omap_hsmmc: make it behave well as a module
mmc: omap_hsmmc: trivial cleanups
mmc: omap_hsmmc: context save after enabling runtime pm
mmc: omap_hsmmc: use runtime put sync in probe error patch
mmc: sdio: Use empty system suspend/resume callbacks at the bus level
mmc: bus: print bus speed mode of UHS-I card
mmc: sdhci-pci: add quirks for broken MSI on O2Micro controllers
mmc: sh_mmcif: Simplify calculation of mmc->f_min
mmc: sh_mmcif: mmc->f_max should be half of the bus clock
mmc: sh_mmcif: double clock speed
mmc: block: Remove use of mmc_blk_set_blksize
mmc: atmel-mci: add support for odd clock dividers
...
Linus Torvalds [Fri, 6 Apr 2012 20:54:56 +0000 (13:54 -0700)]
Make the "word-at-a-time" helper functions more commonly usable
I have a new optimized x86 "strncpy_from_user()" that will use these
same helper functions for all the same reasons the name lookup code uses
them. This is preparation for that.
This moves them into an architecture-specific header file. It's
architecture-specific for two reasons:
- some of the functions are likely to want architecture-specific
implementations. Even if the current code happens to be "generic" in
the sense that it should work on any little-endian machine, it's
likely that the "multiply by a big constant and shift" implementation
is less than optimal for an architecture that has a guaranteed fast
bit count instruction, for example.
- I expect that if architectures like sparc want to start playing
around with this, we'll need to abstract out a few more details (in
particular the actual unaligned accesses). So we're likely to have
more architecture-specific stuff if non-x86 architectures start using
this.
(and if it turns out that non-x86 architectures don't start using
this, then having it in an architecture-specific header is still the
right thing to do, of course)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Toshi Kani [Sun, 1 Apr 2012 03:37:02 +0000 (21:37 -0600)]
cpuidle: Fix panic in CPU off-lining with no idle driver
Fix a NULL pointer dereference panic in cpuidle_play_dead() during
CPU off-lining when no cpuidle driver is registered. A cpuidle
driver may be registered at boot-time based on CPU type. This patch
allows an off-lined CPU to enter HLT-based idle in this condition.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Cc: Boris Ostrovsky <boris.ostrovsky@amd.com>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Tested-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Linus Torvalds [Fri, 6 Apr 2012 17:37:38 +0000 (10:37 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking updates from David Miller:
1) Fix inaccuracies in network driver interface documentation, from Ben
Hutchings.
2) Fix handling of negative offsets in BPF JITs, from Jan Seiffert.
3) Compile warning, locking, and refcounting fixes in netfilter's
xt_CT, from Pablo Neira Ayuso.
4) phonet sendmsg needs to validate user length just like any other
datagram protocol, fix from Sasha Levin.
5) Ipv6 multicast code uses wrong loop index, from RongQing Li.
6) Link handling and firmware fixes in bnx2x driver from Yaniv Rosner
and Yuval Mintz.
7) mlx4 erroneously allocates 4 pages at a time, regardless of page
size, fix from Thadeu Lima de Souza Cascardo.
8) SCTP socket option wasn't extended in a backwards compatible way,
fix from Thomas Graf.
9) Add missing address change event emissions to bonding, from Shlomo
Pongratz.
10) /proc/net/dev regressed because it uses a private offset to track
where we are in the hash table, but this doesn't track the offset
pullback that the seq_file code does resulting in some entries being
missed in large dumps.
Fix from Eric Dumazet.
11) do_tcp_sendpage() unloads the send queue way too fast, because it
invokes tcp_push() when it shouldn't. Let the natural sequence
generated by the splice paths, and the assosciated MSG_MORE
settings, guide the tcp_push() calls.
Otherwise what goes out of TCP is spaghetti and doesn't batch
effectively into GSO/TSO clusters.
From Eric Dumazet.
12) Once we put a SKB into either the netlink receiver's queue or a
socket error queue, it can be consumed and freed up, therefore we
cannot touch it after queueing it like that.
Fixes from Eric Dumazet.
13) PPP has this annoying behavior in that for every transmit call it
immediately stops the TX queue, then calls down into the next layer
to transmit the PPP frame.
But if that next layer can take it immediately, it just un-stops the
TX queue right before returning from the transmit method.
Besides being useless work, it makes several facilities unusable, in
particular things like the equalizers. Well behaved devices should
only stop the TX queue when they really are full, and in PPP's case
when it gets backlogged to the downstream device.
David Woodhouse therefore fixed PPP to not stop the TX queue until
it's downstream can't take data any more.
14) IFF_UNICAST_FLT got accidently lost in some recent stmmac driver
changes, re-add. From Marc Kleine-Budde.
15) Fix link flaps in ixgbe, from Eric W. Multanen.
16) Descriptor writeback fixes in e1000e from Matthew Vick.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
net: fix a race in sock_queue_err_skb()
netlink: fix races after skb queueing
doc, net: Update ndo_start_xmit return type and values
doc, net: Remove instruction to set net_device::trans_start
doc, net: Update netdev operation names
doc, net: Update documentation of synchronisation for TX multiqueue
doc, net: Remove obsolete reference to dev->poll
ethtool: Remove exception to the requirement of holding RTNL lock
MAINTAINERS: update for Marvell Ethernet drivers
bonding: properly unset current_arp_slave on slave link up
phonet: Check input from user before allocating
tcp: tcp_sendpages() should call tcp_push() once
ipv6: fix array index in ip6_mc_add_src()
mlx4: allocate just enough pages instead of always 4 pages
stmmac: re-add IFF_UNICAST_FLT for dwmac1000
bnx2x: Clear MDC/MDIO warning message
bnx2x: Fix BCM57711+BCM84823 link issue
bnx2x: Clear BCM84833 LED after fan failure
bnx2x: Fix BCM84833 PHY FW version presentation
bnx2x: Fix link issue for BCM8727 boards.
...
Jan Beulich [Mon, 2 Apr 2012 14:22:39 +0000 (15:22 +0100)]
xen/pcifront: avoid pci_frontend_enable_msix() falsely returning success
The original XenoLinux code has always had things this way, and for
compatibility reasons (in particular with a subsequent pciback
adjustment) upstream Linux should behave the same way (allowing for two
distinct error indications to be returned by the backend).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Jan Beulich [Mon, 2 Apr 2012 14:32:22 +0000 (15:32 +0100)]
xen/pciback: fix XEN_PCI_OP_enable_msix result
Prior to 2.6.19 and as of 2.6.31, pci_enable_msix() can return a
positive value to indicate the number of vectors (less than the amount
requested) that can be set up for a given device. Returning this as an
operation value (secondary result) is fine, but (primary) operation
results are expected to be negative (error) or zero (success) according
to the protocol. With the frontend fixed to match the XenoLinux
behavior, the backend can now validly return zero (success) here,
passing the upper limit on the number of vectors in op->value.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Srivatsa S. Bhat [Thu, 22 Mar 2012 12:59:24 +0000 (18:29 +0530)]
xen/smp: Remove unnecessary call to smp_processor_id()
There is an extra and unnecessary call to smp_processor_id()
in cpu_bringup(). Remove it.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Konrad Rzeszutek Wilk [Tue, 20 Mar 2012 19:04:18 +0000 (15:04 -0400)]
xen/x86: Workaround 'x86/ioapic: Add register level checks to detect bogus io-apic entries'
The above mentioned patch checks the IOAPIC and if it contains
-1, then it unmaps said IOAPIC. But under Xen we get this:
BUG: unable to handle kernel NULL pointer dereference at
0000000000000040
IP: [<
ffffffff8134e51f>] xen_irq_init+0x1f/0xb0
PGD 0
Oops: 0002 [#1] SMP
CPU 0
Modules linked in:
Pid: 1, comm: swapper/0 Not tainted 3.2.10-3.fc16.x86_64 #1 Dell Inc. Inspiron
1525 /0U990C
RIP: e030:[<
ffffffff8134e51f>] [<
ffffffff8134e51f>] xen_irq_init+0x1f/0xb0
RSP: e02b:
ffff8800d42cbb70 EFLAGS:
00010202
RAX:
0000000000000000 RBX:
00000000ffffffef RCX:
0000000000000001
RDX:
0000000000000040 RSI:
00000000ffffffef RDI:
0000000000000001
RBP:
ffff8800d42cbb80 R08:
ffff8800d6400000 R09:
0000000000000000
R10:
0000000000000000 R11:
0000000000000000 R12:
00000000ffffffef
R13:
0000000000000001 R14:
0000000000000001 R15:
0000000000000010
FS:
0000000000000000(0000) GS:
ffff8800df5fe000(0000) knlGS:
0000000000000000
CS: e033 DS: 0000 ES: 0000 CR0:
000000008005003b
CR2:
0000000000000040 CR3:
0000000001a05000 CR4:
0000000000002660
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000ffff0ff0 DR7:
0000000000000400
Process swapper/0 (pid: 1, threadinfo
ffff8800d42ca000, task
ffff8800d42d0000)
Stack:
00000000ffffffef 0000000000000010 ffff8800d42cbbe0 ffffffff8134f157
ffffffff8100a9b2 ffffffff8182ffd1 00000000000000a0 00000000829e7384
0000000000000002 0000000000000010 00000000ffffffff 0000000000000000
Call Trace:
[<
ffffffff8134f157>] xen_bind_pirq_gsi_to_irq+0x87/0x230
[<
ffffffff8100a9b2>] ? check_events+0x12+0x20
[<
ffffffff814bab42>] xen_register_pirq+0x82/0xe0
[<
ffffffff814bac1a>] xen_register_gsi.part.2+0x4a/0xd0
[<
ffffffff814bacc0>] acpi_register_gsi_xen+0x20/0x30
[<
ffffffff8103036f>] acpi_register_gsi+0xf/0x20
[<
ffffffff8131abdb>] acpi_pci_irq_enable+0x12e/0x202
[<
ffffffff814bc849>] pcibios_enable_device+0x39/0x40
[<
ffffffff812dc7ab>] do_pci_enable_device+0x4b/0x70
[<
ffffffff812dc878>] __pci_enable_device_flags+0xa8/0xf0
[<
ffffffff812dc8d3>] pci_enable_device+0x13/0x20
The reason we are dying is b/c the call acpi_get_override_irq() is used,
which returns the polarity and trigger for the IRQs. That function calls
mp_find_ioapics to get the 'struct ioapic' structure - which along with the
mp_irq[x] is used to figure out the default values and the polarity/trigger
overrides. Since the mp_find_ioapics now returns -1 [b/c the IOAPIC is filled
with 0xffffffff], the acpi_get_override_irq() stops trying to lookup in the
mp_irq[x] the proper INT_SRV_OVR and we can't install the SCI interrupt.
The proper fix for this is going in v3.5 and adds an x86_io_apic_ops
struct so that platforms can override it. But for v3.4 lets carry this
work-around. This patch does that by providing a slightly different variant
of the fake IOAPIC entries.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Igor Mammedov [Tue, 27 Mar 2012 17:31:08 +0000 (19:31 +0200)]
xen: only check xen_platform_pci_unplug if hvm
commit
b9136d207f08
xen: initialize platform-pci even if xen_emul_unplug=never
breaks blkfront/netfront by not loading them because of
xen_platform_pci_unplug=0 and it is never set for PV guest.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Eric Dumazet [Fri, 6 Apr 2012 08:49:10 +0000 (10:49 +0200)]
net: fix a race in sock_queue_err_skb()
As soon as an skb is queued into socket error queue, another thread
can consume it, so we are not allowed to reference skb anymore, or risk
use after free.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 5 Apr 2012 22:17:46 +0000 (22:17 +0000)]
netlink: fix races after skb queueing
As soon as an skb is queued into socket receive_queue, another thread
can consume it, so we are not allowed to reference skb anymore, or risk
use after free.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Thu, 5 Apr 2012 14:40:25 +0000 (14:40 +0000)]
doc, net: Update ndo_start_xmit return type and values
Commit
dc1f8bf68b311b1537cb65893430b6796118498a ('netdev: change
transmit to limited range type') changed the required return type and
9a1654ba0b50402a6bd03c7b0fe9b0200a5ea7b1 ('net: Optimize
hard_start_xmit() return checking') changed the valid numerical
return values.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Thu, 5 Apr 2012 14:40:06 +0000 (14:40 +0000)]
doc, net: Remove instruction to set net_device::trans_start
Commit
08baf561083bc27a953aa087dd8a664bb2b88e8e ('net:
txq_trans_update() helper') made it unnecessary for most drivers to
set net_device::trans_start (or netdev_queue::trans_start).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Thu, 5 Apr 2012 14:39:47 +0000 (14:39 +0000)]
doc, net: Update netdev operation names
Commits
d314774cf2cd5dfeb39a00d37deee65d4c627927 ('netdev: network
device operations infrastructure') and
008298231abbeb91bc7be9e8b078607b816d1a4a ('netdev: add more functions
to netdevice ops') moved and renamed net device operation pointers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Thu, 5 Apr 2012 14:39:30 +0000 (14:39 +0000)]
doc, net: Update documentation of synchronisation for TX multiqueue
Commits
e308a5d806c852f56590ffdd3834d0df0cbed8d7 ('netdev: Add
netdev->addr_list_lock protection.') and
e8a0464cc950972824e2e128028ae3db666ec1ed ('netdev: Allocate multiple
queues for TX.') introduced more fine-grained locks.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Thu, 5 Apr 2012 14:39:10 +0000 (14:39 +0000)]
doc, net: Remove obsolete reference to dev->poll
Commit
bea3348eef27e6044b6161fd04c3152215f96411 ('[NET]: Make NAPI
polling independent of struct net_device objects.') removed the
automatic disabling of NAPI polling by dev_close(), and drivers
must now do this themselves.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Thu, 5 Apr 2012 14:38:49 +0000 (14:38 +0000)]
ethtool: Remove exception to the requirement of holding RTNL lock
Commit
e52ac3398c3d772d372b9b62ab408fd5eec96840 ('net: Use device
model to get driver name in skb_gso_segment()') removed the only
in-tree caller of ethtool ops that doesn't hold the RTNL lock.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 6 Apr 2012 05:13:39 +0000 (22:13 -0700)]
Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull "ARM: SoC fixes: from Olof Johansson:
"A bunch of fixes for regressions (and a few other problems) in
3.4-rc1:
- Fix for regression of mach/io.h cleanup on platforms with PCI or
PCMCIA (adding back the include file on those for now)
- AT91 fixes for usb and spi
- smsc911x ethernet fixes for i.MX
- smsc911x fixes for OMAP
- gpio fixes for Tegra
- A handful of build error and warning fixes for various platforms
- cpufreq kconfig dependencies, build and lowlevel debug fixes for
Samsung platforms
In other words, more or less the regular collection of -rc1/2 type
material. A few of them, in particular the smsc911x for OMAP series,
aren't technically regressions for 3.4, but they're valid fixes and
we're still relatively early in the rc cycle so it seems appropriate
to include them."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
ARM: fix __io macro for PCMCIA
ARM: EXYNOS: Fix compiler warning in dma.c file
ARM: EXYNOS: fix ISO C90 warning
ARM: OMAP2+: hwmod: Fix wrong SYSC_TYPE1_XXX_MASK bit definitions
ARM: OMAP2+: hwmod: Make omap_hwmod_softreset wait for reset status
ARM: OMAP2+: hwmod: Restore sysc after a reset
ARM: OMAP2+: omap_hwmod: Allow io_ring wakeup configuration for all modules
ARM: OMAP3: clock data: fill in some missing clockdomains
ARM: OMAP4: clock data: Force a DPLL clkdm/pwrdm ON before a relock
ARM: OMAP4: clock data: fix mult and div mask for USB_DPLL
ARM: OMAP2+: powerdomain: Wait for powerdomain transition in pwrdm_state_switch()
gpio: tegra: Iterate over the correct number of banks
gpio: tegra: fix register address calculations for Tegra30
EXYNOS: fix dependency for EXYNOS_CPUFREQ
ARM: at91: dt: remove unit-address part for memory nodes
ARM: at91: fix check of valid GPIO for SPI and USB
USB: ehci-atmel: add needed of.h header file
ARM: at91/NAND DT bindings: add comments
ARM: at91/at91sam9x5.dtsi: fix NAND ale/cle in DT file
USB: ohci-at91: trivial return code name change
...
Linus Torvalds [Fri, 6 Apr 2012 04:38:51 +0000 (21:38 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/lliubbo/blackfin
Pull a few blackfin compile fixes from Bob Liu.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lliubbo/blackfin:
blackfin: update defconfig for bf527-ezkit
blackfin: gpio: fix compile error if !CONFIG_GPIOLIB
blackfin: fix L1 data A overflow link issue
Bob Liu [Thu, 5 Apr 2012 02:40:35 +0000 (10:40 +0800)]
blackfin: update defconfig for bf527-ezkit
To fix compile error:
drivers/usb/musb/blackfin.h:51:3: error: #error "Please use PIO mode in MUSB
driver on bf52x chip v0.0 and v0.1"
make[4]: *** [drivers/usb/musb/blackfin.o] Error 1
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Bob Liu [Tue, 27 Mar 2012 03:27:15 +0000 (11:27 +0800)]
blackfin: gpio: fix compile error if !CONFIG_GPIOLIB
Add __gpio_get_value()/__gpio_set_value() to fix compile error if
CONFIG_GPIOLIB = n.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Mike Frysinger [Wed, 28 Mar 2012 03:43:02 +0000 (11:43 +0800)]
blackfin: fix L1 data A overflow link issue
This patch fix below compile error:
"bfin-uclinux-ld: L1 data A overflow!"
It is due to the recent lib/gen_crc32table.c change:
46c5801eaf86e83cb3a4142ad35188db5011fff0
crc32: bolt on crc32c
it added 8KiB more data to __cacheline_aligned which cause blackfin L1 data
cache overflow.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Linus Torvalds [Fri, 6 Apr 2012 00:34:30 +0000 (17:34 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/apm
Pull an APM fix from Jiri Kosina:
"One deadlock/race fix from Niel that got introduced when we were
moving away from freezer_*_count() to wait_event_freezable()."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/apm:
APM: fix deadlock in APM_IOC_SUSPEND ioctl
Paul Walmsley [Mon, 12 Mar 2012 10:58:00 +0000 (04:58 -0600)]
mmc: use really long write timeout to deal with crappy cards
Several people have noticed that crappy SD cards take much longer to
complete multiple block writes than the 300ms that Linux specifies.
Try to work around this by using a three second write timeout instead.
This is a generalized version of a patch from Chase Maupin
<Chase.Maupin@ti.com>, whose patch description said:
* With certain SD cards timeouts like the following have been seen
due to an improper calculation of the dto value:
mmcblk0: error -110 transferring data, sector
4126233, nr 8,
card status 0xc00
* By removing the dto calculation and setting the timeout value
to the maximum specified by the SD card specification part A2
section 2.2.15 these timeouts can be avoided.
* This change has been used by beagleboard users as well as the
Texas Instruments SDK without a negative impact.
* There are multiple discussion threads about this but the most
relevant ones are:
* http://talk.maemo.org/showthread.php?p=
1000707#post1000707
* http://www.mail-archive.com/linux-omap@vger.kernel.org/msg42213.html
* Original proposal for this fix was done by Sukumar Ghoral of
Texas Instruments
* Tested using a Texas Instruments AM335x EVM
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Alf Høgemark [Wed, 4 Apr 2012 16:27:09 +0000 (12:27 -0400)]
mmc: sdhci-dove: Fix compile error by including module.h
This patch fixes a compile error in drivers/mmc/host/sdhci-dove.c
by including the linux/module.h file.
Signed-off-by: Alf Høgemark <alf@i100.no>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Al Cooper [Fri, 16 Mar 2012 19:54:17 +0000 (15:54 -0400)]
mmc: Prevent 1.8V switch for SD hosts that don't support UHS modes.
The driver should not try to switch to 1.8V when the SD 3.0 host
controller does not have any UHS capabilities bits set (SDR50, DDR50
or SDR104). See page 72 of "SD Specifications Part A2 SD Host
Controller Simplified Specification Version 3.00" under
"1.8V Signaling Enable". Instead of setting SDR12 and SDR25 in the host
capabilities data structure for all V3.0 host controllers, only set them
if SDR104, SDR50 or DDR50 is set in the host capabilities register. This
will prevent the switch to 1.8V later.
Signed-off-by: Al Cooper <acooper@gmail.com>
Acked-by: Arindam Nath <arindam.nath@amd.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Acked-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Chris Ball [Tue, 3 Apr 2012 20:48:32 +0000 (16:48 -0400)]
Revert "mmc: sdhci-pci: Add MSI support"
This reverts commit
e6039832bed9a9b967796d7021f17f25b625b616.
There are reports of MSI breaking SDHCI on multiple chipsets (JMicron
and O2Micro, at least), so this should be reverted until we come up
with a whitelist or something.
Signed-off-by: Chris Ball <cjb@laptop.org>
Chris Ball [Tue, 3 Apr 2012 20:47:55 +0000 (16:47 -0400)]
Revert "mmc: sdhci-pci: add quirks for broken MSI on O2Micro controllers"
This reverts commit
c16e981b2fd9455af670a69a84f4c8cf07e12658, because
it's no longer useful once MSI support is reverted.
Signed-off-by: Chris Ball <cjb@laptop.org>
Subhash Jadavani [Tue, 3 Apr 2012 06:55:58 +0000 (12:25 +0530)]
mmc: core: fix power class selection
mmc_select_powerclass() function returns error if eMMC
VDD level supported by host is between 2.7v to 3.2v.
According to eMMC specification, valid voltage for high
voltage cards is 2.7v to 3.6v. This patch ensures that
2.7v to 3.6v VDD range is treated as valid range.
Also, failure to set the power class shouldn't be treated
as fatal error because even if setting the power class
fails, card can still work in default power class.
If mmc_select_powerclass() returns error, just print
the warning message and go ahead with rest of the card
initialization.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Acked-by: Girish K S <girish.shivananjappa@linaro.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Balaji T K [Mon, 2 Apr 2012 06:56:47 +0000 (12:26 +0530)]
mmc: omap_hsmmc: fix module re-insertion
OMAP4 and OMAP3 HSMMC IP registers differ by 0x100 offset.
Adding the offset to platform_device resource structure
increments the start address for every insmod operation.
MMC command fails on re-insertion as module due to incorrect register
base. Fix this by updating the ioremap base address only.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Felipe Balbi [Wed, 14 Mar 2012 09:18:32 +0000 (11:18 +0200)]
mmc: omap_hsmmc: convert to module_platform_driver
This will delete some boilerplate code, no functional changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Felipe Balbi [Wed, 14 Mar 2012 09:18:28 +0000 (11:18 +0200)]
mmc: omap_hsmmc: make it behave well as a module
If we put probe() on __init section, that will never work for multiple
module insertions/removals.
In order to make it work properly, move probe to __devinit section and
use platform_driver_register() instead of platform_driver_probe().
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Felipe Balbi [Wed, 14 Mar 2012 09:18:27 +0000 (11:18 +0200)]
mmc: omap_hsmmc: trivial cleanups
A bunch of non-functional cleanups to the omap_hsmmc driver.
It basically decreases indentation level, drop unneded dereferences
and drop unneded accesses to the platform_device structure.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Balaji T K [Fri, 24 Feb 2012 15:44:34 +0000 (21:14 +0530)]
mmc: omap_hsmmc: context save after enabling runtime pm
Call context save api after enabling runtime pm to make sure that
register access in context save api happens with clk enabled.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Balaji T K [Fri, 24 Feb 2012 15:44:33 +0000 (21:14 +0530)]
mmc: omap_hsmmc: use runtime put sync in probe error patch
pm_runtime_put_sync instead of autosuspend pm runtime API
because iounmap(host->base) follows immediately.
Reported-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Rafael J. Wysocki [Sun, 1 Apr 2012 04:34:58 +0000 (00:34 -0400)]
mmc: sdio: Use empty system suspend/resume callbacks at the bus level
Neil Brown reports that commit
35cd133c
PM: Run the driver callback directly if the subsystem one is not there
breaks suspend for his libertas wifi, because SDIO has a protocol
where the suspend method can return -ENOSYS and this means "There is
no point in suspending, just turn me off". Moreover, the suspend
methods provided by SDIO drivers are not supposed to be called by
the PM core or bus-level suspend routines (which aren't presend for
SDIO). Instead, when the SDIO core gets to suspend the device's
ancestor, it calls the device driver's suspend function, catches the
ENOSYS, and turns the device off.
The commit above breaks the SDIO core's assumption that the device
drivers' callbacks won't be executed if it doesn't provide any
bus-level callbacks. If fact, however, this assumption has never
been really satisfied, because device class or device type suspend
might very well use the driver's callback even without that commit.
The simplest way to address this problem is to make the SDIO core
tell the PM core to ignore driver callbacks, for example by providing
no-operation suspend/resume callbacks at the bus level for it,
which is implemented by this change.
Reported-and-tested-by: Neil Brown <neilb@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
[stable: please apply to 3.3-stable only]
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Subhash Jadavani [Fri, 30 Mar 2012 06:40:18 +0000 (12:10 +0530)]
mmc: bus: print bus speed mode of UHS-I card
When UHS-I card is detected also print the bus speed mode in which
UHS-I card will be running.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Manuel Lauss [Thu, 29 Mar 2012 17:05:04 +0000 (19:05 +0200)]
mmc: sdhci-pci: add quirks for broken MSI on O2Micro controllers
MSI on my O2Micro OZ600 SD card reader is broken. This patch adds a quirk
to disable MSI on these controllers.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Simon Horman [Wed, 28 Mar 2012 09:01:11 +0000 (18:01 +0900)]
mmc: sh_mmcif: Simplify calculation of mmc->f_min
There is no need to tune mmc->f_min to a value near 400kHz as the MMC core
begins testing frequencies at 400kHz regardless of the value of mmc->f_min.
As suggested by Guennadi Liakhovetski.
Cc: Magnus Damm <magnus.damm@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Cao Minh Hiep <hiepcm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
Simon Horman [Wed, 28 Mar 2012 09:01:10 +0000 (18:01 +0900)]
mmc: sh_mmcif: mmc->f_max should be half of the bus clock
mmc->f_max should be half of the bus clock.
And now that mmc->f_max is not equal to the bus clock the
latter should be used directly to calculate mmc->f_min.
Cc: Magnus Damm <magnus.damm@gmail.com>
Tested-by: Cao Minh Hiep <hiepcm@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
Simon Horman [Wed, 28 Mar 2012 09:01:09 +0000 (18:01 +0900)]
mmc: sh_mmcif: double clock speed
Correct an off-by one error when calculating the clock divisor in cases
where the host clock is a power of two of the target clock. Previously the
divisor was one greater than the correct value in these cases leading to
the clock being set at half the desired speed.
Thanks to Guennadi Liakhovetski for working with me on the logic for this
change.
Tested-by: Cao Minh Hiep <hiepcm@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
Ulf Hansson [Thu, 22 Mar 2012 10:47:26 +0000 (11:47 +0100)]
mmc: block: Remove use of mmc_blk_set_blksize
According to the specifications for SD and (e)MMC default
blocksize (named BLOCKLEN in Spec.) must always be 512
bytes. Since we hardcoded to always use 512 bytes, we do
not explicitly have to set it. Future improvements should
potentially make it possible to use a greater blocksize
than 512 bytes, but until then let's skip this.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Subhash Jadavani <subhashj@codeauora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Ludovic Desroches [Wed, 21 Mar 2012 15:41:23 +0000 (16:41 +0100)]
mmc: atmel-mci: add support for odd clock dividers
Add an odd clock divider capability available from v5xx. It also involves
changing the clock divider calculation, and changing the switch-case
statement to use top-down fallthrough.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Ludovic Desroches [Wed, 21 Mar 2012 15:41:22 +0000 (16:41 +0100)]
mmc: atmel-mci: r/w proof capability only available since v2xx
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Ludovic Desroches [Wed, 28 Mar 2012 10:28:33 +0000 (12:28 +0200)]
mmc: atmel-mci: correct data timeout computation
The HSMCI operates at a rate of up to Master Clock divided by two.
Moreover previous calculation can cause overflows and so wrong
timeouts.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Mark Brown [Sun, 1 Apr 2012 03:31:55 +0000 (23:31 -0400)]
mmc: sdhci-s3c: Enable runtime power management
Since most of the work is already done by the core we just need to add
runtime suspend methods and tell the PM core that runtime PM is enabled
for this device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Mark Brown [Sat, 3 Mar 2012 00:46:41 +0000 (00:46 +0000)]
mmc: sdhci-s3c: Use CONFIG_PM_SLEEP to ifdef system suspend
This matches current best practice as one can have runtime PM enabled
without system sleep and CONFIG_PM is defined for both.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Julia Lawall [Fri, 9 Mar 2012 04:24:53 +0000 (23:24 -0500)]
mmc: sdhci-s3c: use devm_ functions
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
By using devm_ioremap, it also removes a potential memory leak, because
there was no call to iounmap in the probe function.
The call to platform_get_resource was moved just to make it closer to the
place where its result it used.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Chris Ball <cjb@laptop.org>
Olof Johansson [Fri, 6 Apr 2012 00:09:45 +0000 (17:09 -0700)]
Merge tag 'omap-fixes-a2-for-3.4rc' of git://git./linux/kernel/git/pjw/omap-pending into fixes
From Paul Walmsley:
OMAP clock, powerdomain, clockdomain, and hwmod fixes intended for the
early v3.4-rc series. Also contains an HSMMC integration refinement
of an earlier hardware bug workaround.
* tag 'omap-fixes-a2-for-3.4rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: OMAP2+: hwmod: Fix wrong SYSC_TYPE1_XXX_MASK bit definitions
ARM: OMAP2+: hwmod: Make omap_hwmod_softreset wait for reset status
ARM: OMAP2+: hwmod: Restore sysc after a reset
ARM: OMAP2+: omap_hwmod: Allow io_ring wakeup configuration for all modules
ARM: OMAP3: clock data: fill in some missing clockdomains
ARM: OMAP4: clock data: Force a DPLL clkdm/pwrdm ON before a relock
ARM: OMAP4: clock data: fix mult and div mask for USB_DPLL
ARM: OMAP2+: powerdomain: Wait for powerdomain transition in pwrdm_state_switch()
ARM: OMAP AM3517/3505: clock data: change EMAC clocks aliases
ARM: OMAP: clock: fix race in disable all clocks
ARM: OMAP4: hwmod data: Add aliases for McBSP fclk clocks
ARM: OMAP3xxx: clock data: fix DPLL4 CLKSEL masks
ARM: OMAP3xxx: HSMMC: avoid erratum workaround when transceiver is attached
ARM: OMAP44xx: clockdomain data: correct the emu_sys_clkdm CLKTRCTRL data
Thomas Abraham [Thu, 16 Feb 2012 13:23:59 +0000 (22:23 +0900)]
mmc: sdhci-s3c: Keep a copy of platform data and use it
The platform data is copied into driver's private data and the copy is
used for all access to the platform data. This simpifies the addition
of device tree support for the sdhci-s3c driver.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Thomas Abraham [Sun, 1 Apr 2012 03:29:45 +0000 (23:29 -0400)]
mmc: sdhci-s3c: derive transfer width host cap from max_width in platdata
max_width member in platform data can be used to derive the mmc bus transfer
width that can be supported by the controller.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Thomas Abraham [Thu, 16 Feb 2012 13:23:58 +0000 (22:23 +0900)]
mmc: sdhci-s3c: Remove usage of clk_type member in platform data
SDHCI controllers on Exynos4 do not include the sdclk divider as per the
sdhci controller specification. This case can be represented using the
sdhci quirk SDHCI_QUIRK_NONSTANDARD_CLOCK instead of using an additional
enum type definition 'clk_types'.
Hence, usage of clk_type member in platform data is removed and the sdhci
quirk is used. In addition to that, since this qurik is SoC specific,
driver data is introduced to represent controllers on SoC's that require
this quirk.
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Jeongbae Seo <jeongbae.seo@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
stephen hemminger [Mon, 2 Apr 2012 12:59:47 +0000 (12:59 +0000)]
MAINTAINERS: update for Marvell Ethernet drivers
Marvell has agreed to do maintenance on the sky2 driver.
* Add the developer to the maintainers file
* Remove the old reference to the long gone (sk98lin) driver
* Rearrange to fit current topic organization
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Veaceslav Falico [Thu, 5 Apr 2012 03:47:43 +0000 (03:47 +0000)]
bonding: properly unset current_arp_slave on slave link up
When a slave comes up, we're unsetting the current_arp_slave without
removing active flags from it, which can lead to situations where we have
more than one slave with active flags in active-backup mode.
To avoid this situation we must remove the active flags from a slave before
removing it as a current_arp_slave.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sasha Levin [Thu, 5 Apr 2012 12:07:45 +0000 (12:07 +0000)]
phonet: Check input from user before allocating
A phonet packet is limited to USHRT_MAX bytes, this is never checked during
tx which means that the user can specify any size he wishes, and the kernel
will attempt to allocate that size.
In the good case, it'll lead to the following warning, but it may also cause
the kernel to kick in the OOM and kill a random task on the server.
[ 8921.744094] WARNING: at mm/page_alloc.c:2255 __alloc_pages_slowpath+0x65/0x730()
[ 8921.749770] Pid: 5081, comm: trinity Tainted: G W 3.4.0-rc1-next-
20120402-sasha #46
[ 8921.756672] Call Trace:
[ 8921.758185] [<
ffffffff810b2ba7>] warn_slowpath_common+0x87/0xb0
[ 8921.762868] [<
ffffffff810b2be5>] warn_slowpath_null+0x15/0x20
[ 8921.765399] [<
ffffffff8117eae5>] __alloc_pages_slowpath+0x65/0x730
[ 8921.769226] [<
ffffffff81179c8a>] ? zone_watermark_ok+0x1a/0x20
[ 8921.771686] [<
ffffffff8117d045>] ? get_page_from_freelist+0x625/0x660
[ 8921.773919] [<
ffffffff8117f3a8>] __alloc_pages_nodemask+0x1f8/0x240
[ 8921.776248] [<
ffffffff811c03e0>] kmalloc_large_node+0x70/0xc0
[ 8921.778294] [<
ffffffff811c4bd4>] __kmalloc_node_track_caller+0x34/0x1c0
[ 8921.780847] [<
ffffffff821b0e3c>] ? sock_alloc_send_pskb+0xbc/0x260
[ 8921.783179] [<
ffffffff821b3c65>] __alloc_skb+0x75/0x170
[ 8921.784971] [<
ffffffff821b0e3c>] sock_alloc_send_pskb+0xbc/0x260
[ 8921.787111] [<
ffffffff821b002e>] ? release_sock+0x7e/0x90
[ 8921.788973] [<
ffffffff821b0ff0>] sock_alloc_send_skb+0x10/0x20
[ 8921.791052] [<
ffffffff824cfc20>] pep_sendmsg+0x60/0x380
[ 8921.792931] [<
ffffffff824cb4a6>] ? pn_socket_bind+0x156/0x180
[ 8921.794917] [<
ffffffff824cb50f>] ? pn_socket_autobind+0x3f/0x90
[ 8921.797053] [<
ffffffff824cb63f>] pn_socket_sendmsg+0x4f/0x70
[ 8921.798992] [<
ffffffff821ab8e7>] sock_aio_write+0x187/0x1b0
[ 8921.801395] [<
ffffffff810e325e>] ? sub_preempt_count+0xae/0xf0
[ 8921.803501] [<
ffffffff8111842c>] ? __lock_acquire+0x42c/0x4b0
[ 8921.805505] [<
ffffffff821ab760>] ? __sock_recv_ts_and_drops+0x140/0x140
[ 8921.807860] [<
ffffffff811e07cc>] do_sync_readv_writev+0xbc/0x110
[ 8921.809986] [<
ffffffff811958e7>] ? might_fault+0x97/0xa0
[ 8921.811998] [<
ffffffff817bd99e>] ? security_file_permission+0x1e/0x90
[ 8921.814595] [<
ffffffff811e17e2>] do_readv_writev+0xe2/0x1e0
[ 8921.816702] [<
ffffffff810b8dac>] ? do_setitimer+0x1ac/0x200
[ 8921.818819] [<
ffffffff810e2ec1>] ? get_parent_ip+0x11/0x50
[ 8921.820863] [<
ffffffff810e325e>] ? sub_preempt_count+0xae/0xf0
[ 8921.823318] [<
ffffffff811e1926>] vfs_writev+0x46/0x60
[ 8921.825219] [<
ffffffff811e1a3f>] sys_writev+0x4f/0xb0
[ 8921.827127] [<
ffffffff82658039>] system_call_fastpath+0x16/0x1b
[ 8921.829384] ---[ end trace
dffe390f30db9eb7 ]---
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Acked-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>