Linus Torvalds [Tue, 17 Mar 2009 15:59:33 +0000 (08:59 -0700)]
Merge git://git./linux/kernel/git/agk/linux-2.6-dm
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm:
dm crypt: wait for endio to complete before destruction
dm crypt: fix kcryptd_async_done parameter
dm io: respect BIO_MAX_PAGES limit
dm table: rework reference counting fix
dm ioctl: validate name length when renaming
Linus Torvalds [Tue, 17 Mar 2009 15:13:17 +0000 (08:13 -0700)]
Fast TSC calibration: calculate proper frequency error bounds
In order for ntpd to correctly synchronize the clocks, the frequency of
the system clock must not be off by more than 500 ppm (or, put another
way, 1:2000), or ntpd will end up giving up on trying to synchronize
properly, and ends up reseting the clock in jumps instead.
The fast TSC PIT calibration sometimes failed this test - it was
assuming that the PIT reads always took about one microsecond each (2us
for the two reads to get a 16-bit timer), and that calibrating TSC to
the PIT over 15ms should thus be sufficient to get much closer than
500ppm (max 2us error on both sides giving 4us over 15ms: a 270 ppm
error value).
However, that assumption does not always hold: apparently some hardware
is either very much slower at reading the PIT registers, or there was
other noise causing at least one machine to get 700+ ppm errors.
So instead of using a fixed 15ms timing loop, this changes the fast PIT
calibration to read the TSC delta over the individual PIT timer reads,
and use the result to calculate the error bars on the PIT read timing
properly. We then successfully calibrate the TSC only if the maximum
error bars fall below 500ppm.
In the process, we also relax the timing to allow up to 25ms for the
calibration, although it can happen much faster depending on hardware.
Reported-and-tested-by: Jesper Krogh <jesper@krogh.cc>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 17 Mar 2009 14:58:26 +0000 (07:58 -0700)]
Fix potential fast PIT TSC calibration startup glitch
During bootup, when we reprogram the PIT (programmable interval timer)
to start counting down from 0xffff in order to use it for the fast TSC
calibration, we should also make sure to delay a bit afterwards to allow
the PIT hardware to actually start counting with the new value.
That will happens at the next CLK pulse (1.193182 MHz), so the easiest
way to do that is to just wait at least one microsecond after
programming the new PIT counter value. We do that by just reading the
counter value back once - which will take about 2us on PC hardware.
Reported-and-tested-by: john stultz <johnstul@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 16 Mar 2009 19:49:12 +0000 (12:49 -0700)]
Merge branch 'release' of git://git./linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
acpi-wmi: unsigned cannot be less than 0
thinkpad-acpi: fix module autoloading for older models
acer-wmi: Unmark as 'experimental'
acpi-wmi: Unmark as 'experimental'
acer-wmi: double free in acer_rfkill_exit()
platform/x86: depends instead of select for laptop platform drivers
asus-laptop: use select instead of depends on
eeepc-laptop: restore acpi_generate_proc_event()
asus-laptop: restore acpi_generate_proc_event()
acpi: check for pxm_to_node_map overflow
ACPI: remove doubled status checking
ACPI suspend: Blacklist Toshiba Satellite L300 that requires to set SCI_EN directly on resume
Revert "ACPI: make some IO ports off-limits to AML"
suspend: switch the Asus Pundit P1-AH2 to old ACPI sleep ordering
Milan Broz [Mon, 16 Mar 2009 17:44:36 +0000 (17:44 +0000)]
dm crypt: wait for endio to complete before destruction
The following oops has been reported when dm-crypt runs over a loop device.
...
[ 70.381058] Process loop0 (pid: 4268, ti=
cf3b2000 task=
cf1cc1f0 task.ti=
cf3b2000)
...
[ 70.381058] Call Trace:
[ 70.381058] [<
d0d76601>] ? crypt_dec_pending+0x5e/0x62 [dm_crypt]
[ 70.381058] [<
d0d767b8>] ? crypt_endio+0xa2/0xaa [dm_crypt]
[ 70.381058] [<
d0d76716>] ? crypt_endio+0x0/0xaa [dm_crypt]
[ 70.381058] [<
c01a2f24>] ? bio_endio+0x2b/0x2e
[ 70.381058] [<
d0806530>] ? dec_pending+0x224/0x23b [dm_mod]
[ 70.381058] [<
d08066e4>] ? clone_endio+0x79/0xa4 [dm_mod]
[ 70.381058] [<
d080666b>] ? clone_endio+0x0/0xa4 [dm_mod]
[ 70.381058] [<
c01a2f24>] ? bio_endio+0x2b/0x2e
[ 70.381058] [<
c02bad86>] ? loop_thread+0x380/0x3b7
[ 70.381058] [<
c02ba8a1>] ? do_lo_send_aops+0x0/0x165
[ 70.381058] [<
c013754f>] ? autoremove_wake_function+0x0/0x33
[ 70.381058] [<
c02baa06>] ? loop_thread+0x0/0x3b7
When a table is being replaced, it waits for I/O to complete
before destroying the mempool, but the endio function doesn't
call mempool_free() until after completing the bio.
Fix it by swapping the order of those two operations.
The same problem occurs in dm.c with md referenced after dec_pending.
Again, we swap the order.
Cc: stable@kernel.org
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Huang Ying [Mon, 16 Mar 2009 17:44:33 +0000 (17:44 +0000)]
dm crypt: fix kcryptd_async_done parameter
In the async encryption-complete function (kcryptd_async_done), the
crypto_async_request passed in may be different from the one passed to
crypto_ablkcipher_encrypt/decrypt. Only crypto_async_request->data is
guaranteed to be same as the one passed in. The current
kcryptd_async_done uses the passed-in crypto_async_request directly
which may cause the AES-NI-based AES algorithm implementation to panic.
This patch fixes this bug by only using crypto_async_request->data,
which points to dm_crypt_request, the crypto_async_request passed in.
The original data (convert_context) is gotten from dm_crypt_request.
[mbroz@redhat.com: reworked]
Cc: stable@kernel.org
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Mikulas Patocka [Mon, 16 Mar 2009 17:44:30 +0000 (17:44 +0000)]
dm io: respect BIO_MAX_PAGES limit
dm-io calls bio_get_nr_vecs to get the maximum number of pages to use
for a given device. It allocates one additional bio_vec to use
internally but failed to respect BIO_MAX_PAGES, so fix this.
This was the likely cause of:
https://bugzilla.redhat.com/show_bug.cgi?id=173153
Cc: stable@kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Mikulas Patocka [Mon, 16 Mar 2009 17:44:26 +0000 (17:44 +0000)]
dm table: rework reference counting fix
Fix an error introduced in dm-table-rework-reference-counting.patch.
When there is failure after table initialization, we need to use
dm_table_destroy, not dm_table_put, to free the table.
dm_table_put may be used only after dm_table_get.
Cc: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Reviewed-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Milan Broz [Mon, 16 Mar 2009 16:56:01 +0000 (16:56 +0000)]
dm ioctl: validate name length when renaming
When renaming a mapped device validate the length of the new name.
The rename ioctl accepted any correctly-terminated string enclosed
within the data passed from userspace. The other ioctls enforce a
size limit of DM_NAME_LEN. If the name is changed and becomes longer
than that, the device can no longer be addressed by name.
Fix it by properly checking for device name length (including
terminating zero).
Cc: stable@kernel.org
Signed-off-by: Milan Broz <mbroz@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Reviewed-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Linus Torvalds [Mon, 16 Mar 2009 14:56:58 +0000 (07:56 -0700)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
r8169: revert "r8169: read MAC address from EEPROM on init (2nd attempt)"
r8169: use hardware auto-padding.
igb: remove ASPM L0s workaround
netxen: remove old flash check.
mv643xx_eth: fix unicast address filter corruption on mtu change
xfrm: Fix xfrm_state_find() wrt. wildcard source address.
emac: Fix clock control for 405EX and 405EXr chips
ixgbe: fix multiple unicast address support
via-velocity: Fix DMA mapping length errors on transmit.
qlge: bugfix: Pad outbound frames smaller than 60 bytes.
qlge: bugfix: Move netif_napi_del() to common call point.
qlge: bugfix: Tell hw to strip vlan header.
qlge: bugfix: Increase filter on inbound csum.
dnet: replace obsolete *netif_rx_* functions with *napi_*
net: Add be2net driver.
dnet: Fix warnings on 64-bit.
dnet: Dave DNET ethernet controller driver (updated)
ipv6: Fix BUG when disabled ipv6 module is unloaded
bnx2x: Using DMAE to initialize the chip
bnx2x: Casting page alignment
...
Rusty Russell [Sun, 15 Mar 2009 22:35:07 +0000 (09:05 +1030)]
linux.conf.au 2009: Tuz
Impact: help prevent extinction of species
The Tasmanian Devil is a shy iconic Australian creature named for its
spine-chilling screech. It is threatened with extinction due to a
scientifically interesting but horrific transmissible facial cancer.
This one is standing in for Tux for one release using the far less-known
Devil Facial Tux Disguise.
Save The Tasmanian Devil http://tassiedevil.com.au
Signed-off-by: Linux.conf.au Hobart Team <contact@marchsouth.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Zhang Le [Mon, 16 Mar 2009 06:44:31 +0000 (14:44 +0800)]
filp->f_pos not correctly updated in proc_task_readdir
filp->f_pos only get updated at the end of the function. Thus d_off of those
dirents who are in the middle will be 0, and this will cause a problem in
glibc's readdir implementation, specifically endless loop. Because when overflow
occurs, f_pos will be set to next dirent to read, however it will be 0, unless
the next one is the last one. So it will start over again and again.
There is a sample program in man 2 gendents. This is the output of the program
running on a multithread program's task dir before this patch is applied:
$ ./a.out /proc/3807/task
--------------- nread=128 ---------------
i-node# file type d_reclen d_off d_name
506442 directory 16 1 .
506441 directory 16 0 ..
506443 directory 16 0 3807
506444 directory 16 0 3809
506445 directory 16 0 3812
506446 directory 16 0 3861
506447 directory 16 0 3862
506448 directory 16 8 3863
This is the output after this patch is applied
$ ./a.out /proc/3807/task
--------------- nread=128 ---------------
i-node# file type d_reclen d_off d_name
506442 directory 16 1 .
506441 directory 16 2 ..
506443 directory 16 3 3807
506444 directory 16 4 3809
506445 directory 16 5 3812
506446 directory 16 6 3861
506447 directory 16 7 3862
506448 directory 16 8 3863
Signed-off-by: Zhang Le <r0bertz@gentoo.org>
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Len Brown [Mon, 16 Mar 2009 04:38:52 +0000 (00:38 -0400)]
Merge branches 'misc-up-now' and 'platform-drivers' into release
Roel Kluin [Wed, 4 Mar 2009 19:55:30 +0000 (11:55 -0800)]
acpi-wmi: unsigned cannot be less than 0
include/linux/pci-acpi.h:74:
typedef u32 acpi_status;
result is unsigned, so an error returned by acpi_bus_register_driver()
will not be noticed.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Mathieu Chouquet-Stringer [Sat, 14 Mar 2009 15:35:26 +0000 (16:35 +0100)]
thinkpad-acpi: fix module autoloading for older models
Looking at the source, there seems to be a missing * to match my DMI
string. I mean for newer IBM and Lenovo's laptops you match either one
of the following:
MODULE_ALIAS("dmi:bvnIBM:*:svnIBM:*:pvrThinkPad*:rvnIBM:*");
MODULE_ALIAS("dmi:bvnLENOVO:*:svnLENOVO:*:pvrThinkPad*:rvnLENOVO:*");
While for older Thinkpads, you do this (for instance):
IBM_BIOS_MODULE_ALIAS("1[0,3,6,8,A-G,I,K,M-P,S,T]");
with IBM_BIOS_MODULE_ALIAS being MODULE_ALIAS("dmi:bvnIBM:bvr" __type "ET??WW")
Note there's no * terminating the string. As result, udev doesn't load
anything because modprobe cannot find anything matching this (my
machine actually):
udevtest: run: '/sbin/modprobe dmi:bvnIBM:bvr1IET71WW(2.10):bd06/16/2006:svnIBM:pn236621U:pvrNotAv
Signed-off-by: Mathieu Chouquet-Stringer <mchouque@free.fr>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Len Brown <len.brown@intel.com>
Carlos Corbacho [Sat, 14 Feb 2009 09:53:59 +0000 (09:53 +0000)]
acer-wmi: Unmark as 'experimental'
This driver has been around and used long enough that we can drop the
'experimental'.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
Carlos Corbacho [Sat, 14 Feb 2009 09:53:53 +0000 (09:53 +0000)]
acpi-wmi: Unmark as 'experimental'
ACPI-WMI isn't experimental anymore, and there are other drivers that now
depend on it that aren't either.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
Dan Carpenter [Sat, 14 Feb 2009 09:53:48 +0000 (09:53 +0000)]
acer-wmi: double free in acer_rfkill_exit()
This is acer_rfkill_exit() from drivers/platform/x86/acer-wmi.c.
The code frees wireless_rfkill->data again instead of
bluetooth_rfkill->data.
This was found using a code checker (http://repo.or.cz/w/smatch.git/).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
Corentin Chary [Wed, 25 Feb 2009 08:37:09 +0000 (09:37 +0100)]
platform/x86: depends instead of select for laptop platform drivers
"I hate `select' and will gleefully leap on any s/select/depends/ patch,
whether it works or not :)"
Andrew Morton
select INPUT is not needed here, because if someone doesn't want INPUT,
he won't want these drivers either.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
Corentin Chary [Sun, 15 Feb 2009 18:30:21 +0000 (19:30 +0100)]
asus-laptop: use select instead of depends on
Like thinkpad_acpi or eeepc-laptop, asus-laptop will
now use "select" instead of "depends on"
for LEDS_CLASS, NEW_LEDS and BACKLIGHT_CLASS_DEVICE
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
Corentin Chary [Sun, 15 Feb 2009 18:30:20 +0000 (19:30 +0100)]
eeepc-laptop: restore acpi_generate_proc_event()
Restore acpi_generate_proc_event() for backward
compatibility with old acpi scripts.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
Corentin Chary [Sun, 15 Feb 2009 18:30:19 +0000 (19:30 +0100)]
asus-laptop: restore acpi_generate_proc_event()
Restore acpi_generate_proc_event() for backward
compatibility with old acpi scripts.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
Cyrill Gorcunov [Wed, 4 Mar 2009 19:55:29 +0000 (11:55 -0800)]
acpi: check for pxm_to_node_map overflow
It is hardly (if ever) possible but in case of broken _PXM entry we could
reach out of pxm_to_node_map array bounds in acpi_map_pxm_to_node() call.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Jiri Slaby [Wed, 4 Mar 2009 19:55:27 +0000 (11:55 -0800)]
ACPI: remove doubled status checking
There was a misplaced status test (two consequent tests without a
statement in between) in acpi_bus_init for ages. Remove it, since the
function which should be checked (acpi_os_initialize1) has BUG_ONs on
failure paths.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Zhang Rui [Mon, 16 Mar 2009 02:13:44 +0000 (22:13 -0400)]
ACPI suspend: Blacklist Toshiba Satellite L300 that requires to set SCI_EN directly on resume
This is a supplement of commit
65df78473ffbf3bff5e2034df1638acc4f3ddd50.
http://bugzilla.kernel.org/show_bug.cgi?id=12798
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Len Brown [Wed, 25 Feb 2009 23:00:18 +0000 (18:00 -0500)]
Revert "ACPI: make some IO ports off-limits to AML"
This reverts commit
5ec5d38a1c8af255ffc481c81eef13e9155524b3.
because it caused spurious dmesg warmings.
We'll implement the check for off-limit ports
in a more clever way in the future.
http://bugzilla.kernel.org/show_bug.cgi?id=12758
Signed-off-by: Len Brown <len.brown@intel.com>
Andy Whitcroft [Wed, 11 Feb 2009 18:11:22 +0000 (18:11 +0000)]
suspend: switch the Asus Pundit P1-AH2 to old ACPI sleep ordering
Switch the Asus Pundit P1-AH2 (M2N8L motherboard) to the old ACPI 1.0
sleep ordering by default. Without this it will not suspend/resume
correctly.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Tested-by: Dustin Kirkland <kirkland@canonical.com>
Signed-off-by: Len Brown <len.brown@intel.com>
françois romieu [Sun, 15 Mar 2009 01:10:50 +0000 (01:10 +0000)]
r8169: revert "r8169: read MAC address from EEPROM on init (2nd attempt)"
It fails on the following systems:
- RTL8169sc/8110sc (XID
18000000)
reported by Tim Durack <tdurack@gmail.com> (x86)
- RTL8169sb/8110sb (XID
10000000)
reported by Mikael Pettersson <mikpe@it.uu.se> (ARM)
The patch appeared to work on x86 for the following systems:
RTL8169sb/8110sb
10000000 PCI (EXT)
RTL8110s
04000000 PCI (EXT)
RTL8102e
24a00000 PCI-E (LOM)
RTL8168c/8111c
3c2000c0 PCI-E (LOM)
RTL8168b/8111b
38000000 PCI-E (LOM)
RTL8168b/8111b
38000000 PCI-E (EXT)
The patch exposes two problems:
1) while not completely wrong, mac addresses are not read correctly
from the EEPROM
2) the MAC address registers are not correctly set
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
françois romieu [Sun, 15 Mar 2009 01:09:54 +0000 (01:09 +0000)]
r8169: use hardware auto-padding.
It shortens the code and fixes the current pci_unmap leak with
padded skb reported by Dave Jones.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kyle McMartin [Sat, 14 Mar 2009 23:40:59 +0000 (19:40 -0400)]
parisc: sba_iommu: fix build bug when CONFIG_PARISC_AGP=y
CC drivers/parisc/sba_iommu.o
drivers/parisc/sba_iommu.c:1373: error: expected identifier or '('
before '}' token
make[2]: *** [drivers/parisc/sba_iommu.o] Error 1
make[1]: *** [drivers/parisc] Error 2
make: *** [drivers] Error 2
Don't know how this has gone missed for so long... clearly I need
to do builds on my C8000 more often.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 15 Mar 2009 20:34:56 +0000 (13:34 -0700)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm: (23 commits)
[ARM] Fix virtual to physical translation macro corner cases
[ARM] update mach-types
[ARM] 5421/1: ftrace: fix crash due to tracing of __naked functions
MX1 fix include
[ARM] 5419/1: ep93xx: fix build warnings about struct i2c_board_info
[ARM] 5418/1: restore lr before leaving mcount
ARM: OMAP: board-omap3beagle: set i2c-3 to 100kHz
ARM: OMAP: Allow I2C bus driver to be compiled as a module
ARM: OMAP: sched_clock() corrected
ARM: OMAP: Fix compile error if pm.h is included
[ARM] orion5x: pass dram mbus data to xor driver
[ARM] S3C64XX: Fix s3c64xx_setrate_clksrc
[ARM] S3C64XX: sparse warnings in arch/arm/plat-s3c64xx/irq.c
[ARM] S3C64XX: sparse warnings in arch/arm/plat-s3c64xx/s3c6400-clock.c
[ARM] S3C64XX: Fix USB host clock mux list
[ARM] S3C64XX: Fix name of USB host clock.
[ARM] S3C64XX: Rename IRQ_UHOST to IRQ_USBH
[ARM] S3C64XX: Do gpiolib configuration earlier
[ARM] S3C64XX: Staticise s3c64xx_init_irq_eint()
[ARM] SMDK6410: Declare iodesc table static
...
Alexander Duyck [Sun, 15 Mar 2009 05:26:40 +0000 (22:26 -0700)]
igb: remove ASPM L0s workaround
The L0s workaround should be moved into a pci quirk and so it is not
necessary in the driver. This update removes the L0s workaround from the
igb driver.
This was the second half of the PCI quirk patch that Matthew Wilcox did
not pick up when he picked up the quirk patch.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 14 Mar 2009 20:43:18 +0000 (13:43 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
Fix Xilinx SystemACE driver to handle empty CF slot
block: fix memory leak in bio_clone()
block: Add gfp_mask parameter to bio_integrity_clone()
Grant Likely [Mon, 9 Mar 2009 12:42:24 +0000 (13:42 +0100)]
Fix Xilinx SystemACE driver to handle empty CF slot
The SystemACE driver does not handle an empty CF slot gracefully. An
empty CF slot ends up hanging the system. This patch adds a check for
the CF state and stops trying to process requests if the slot is empty.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Li Zefan [Mon, 9 Mar 2009 09:42:45 +0000 (10:42 +0100)]
block: fix memory leak in bio_clone()
If bio_integrity_clone() fails, bio_clone() returns NULL without freeing
the newly allocated bio.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
un'ichi Nomura [Mon, 9 Mar 2009 09:40:52 +0000 (10:40 +0100)]
block: Add gfp_mask parameter to bio_integrity_clone()
Stricter gfp_mask might be required for clone allocation.
For example, request-based dm may clone bio in interrupt context
so it has to use GFP_ATOMIC.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Linus Torvalds [Sat, 14 Mar 2009 19:02:21 +0000 (12:02 -0700)]
Merge branch 'upstream' of git://ftp.linux-mips.org/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: Mark Eins: Fix configuration.
MIPS: Fix TIF_32BIT undefined problem when seccomp is disabled
Linus Torvalds [Sat, 14 Mar 2009 19:01:37 +0000 (12:01 -0700)]
Merge git://git./linux/kernel/git/jejb/scsi-rc-fixes-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (31 commits)
[SCSI] qla2xxx: Update version number to 8.03.00-k4.
[SCSI] qla2xxx: Correct overwrite of pre-assigned init-control-block structure size.
[SCSI] qla2xxx: Correct truncation in return-code status checking.
[SCSI] qla2xxx: Correct vport delete bug.
[SCSI] qla2xxx: Use correct value for max vport in LOOP topology.
[SCSI] qla2xxx: Correct address range checking for option-rom updates.
[SCSI] fcoe: Change fcoe receive thread nice value from 19 (lowest priority) to -20
[SCSI] fcoe: fix handling of pending queue, prevent out of order frames (v3)
[SCSI] fcoe: Out of order tx frames was causing several check condition SCSI status
[SCSI] fcoe: fix kfree(skb)
[SCSI] fcoe: ETH_P_8021Q is already in if_ether and fcoe is not using it anyway
[SCSI] libfc: do not change the fh_rx_id of a recevied frame
[SCSI] fcoe: Correct fcoe_transports initialization vs. registration
[SCSI] fcoe: Use setup_timer() and mod_timer()
[SCSI] libfc, fcoe: Remove unnecessary cast by removing inline wrapper
[SCSI] libfc, fcoe: Cleanup function formatting and minor typos
[SCSI] libfc, fcoe: Fix kerneldoc comments
[SCSI] libfc: Cleanup libfc_function_template comments
[SCSI] libfc: check for err when recv and state is incorrect
[SCSI] libfc: rename rp to rdata in fc_disc_new_target()
...
Linus Torvalds [Sat, 14 Mar 2009 19:00:42 +0000 (12:00 -0700)]
Merge branch 'upstream-linus' of git://git./linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ata_piix: add workaround for Samsung DB-P70
libata: Keep shadow last_ctl up to date during resets
sata_mv: fix MSI irq race condition
Linus Torvalds [Sat, 14 Mar 2009 19:00:18 +0000 (12:00 -0700)]
Merge branch 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFS: Fix the fix to Bugzilla #11061, when IPv6 isn't defined...
SUNRPC: xprt_connect() don't abort the task if the transport isn't bound
SUNRPC: Fix an Oops due to socket not set up yet...
Bug 11061, NFS mounts dropped
NFS: Handle -ESTALE error in access()
NLM: Fix GRANT callback address comparison when IPv6 is enabled
NLM: Shrink the IPv4-only version of nlm_cmp_addr()
NFSv3: Fix posix ACL code
NFS: Fix misparsing of nfsv4 fs_locations attribute (take 2)
SUNRPC: Tighten up the task locking rules in __rpc_execute()
Linus Torvalds [Sat, 14 Mar 2009 18:59:22 +0000 (11:59 -0700)]
Merge branch 'upstream-linus' of git://git./linux/kernel/git/mfasheh/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
ocfs2: Use xs->bucket to set xattr value outside
ocfs2: Fix a bug found by sparse check.
ocfs2: tweak to get the maximum inline data size with xattr
ocfs2: reserve xattr block for new directory with inline data
Linus Torvalds [Sat, 14 Mar 2009 18:59:05 +0000 (11:59 -0700)]
Merge branch 'for_linus' of git://git./linux/kernel/git/mchehab/linux-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
V4L/DVB (10978): Report tuning algorith correctly
V4L/DVB (10977): STB6100 init fix, the call to stb6100_set_bandwidth needs an argument
V4L/DVB (10976): Bug fix: For legacy applications stv0899 performs search only first time after insmod.
V4L/DVB (10975): Bug: Use signed types, Offsets and range can be negative
V4L/DVB (10974): Use Diseqc 3/3 mode to send data
V4L/DVB (10972): zl10353: i2c_gate_ctrl bug fix
V4L/DVB (10834): zoran: auto-select bt866 for AverMedia 6 Eyes
V4L/DVB (10832): tvaudio: Avoid breakage with tda9874a
V4L/DVB (10789): m5602-s5k4aa: Split up the initial sensor probe in chunks.
Linus Torvalds [Sat, 14 Mar 2009 18:58:38 +0000 (11:58 -0700)]
Merge git://git./linux/kernel/git/kyle/parisc-2.6.29
* git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6.29:
parisc: update defconfigs
parisc: define x->x mmio accessors
parisc: dino: struct device - replace bus_id with dev_name(), dev_set_name()
parisc: convert cpu_check_affinity to new cpumask api
parisc: convert (read|write)bwlq to inlines
parisc: fix use of new cpumask api in irq.c
parisc: update parisc for new irq_desc
parisc: update MAINTAINERS
parisc: fix wrong assumption about bus->self
parisc: fix 64bit build
parisc: add braces around arguments in assembler macros
parisc: fix dev_printk() compile warnings for accessing a device struct
parisc: remove unused local out_putf label
parisc: fix `struct pt_regs' declared inside parameter list warning
parisc: fix section mismatch warnings
parisc: remove klist iterators
parisc: BUG_ON() cleanup
Linus Torvalds [Sat, 14 Mar 2009 18:58:10 +0000 (11:58 -0700)]
Merge git://git./linux/kernel/git/bart/ide-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: save the returned value of dma_map_sg
ide-floppy: do not map dataless cmds to an sg
Daisuke Nishimura [Fri, 13 Mar 2009 20:52:00 +0000 (13:52 -0700)]
vmscan: pgmoved should be cleared after updating recent_rotated
pgmoved should be cleared after updating recent_rotated.
Signed-off-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Rik van Riel <riel@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tyler Hicks [Fri, 13 Mar 2009 20:51:59 +0000 (13:51 -0700)]
eCryptfs: don't encrypt file key with filename key
eCryptfs has file encryption keys (FEK), file encryption key encryption
keys (FEKEK), and filename encryption keys (FNEK). The per-file FEK is
encrypted with one or more FEKEKs and stored in the header of the
encrypted file. I noticed that the FEK is also being encrypted by the
FNEK. This is a problem if a user wants to use a different FNEK than
their FEKEK, as their file contents will still be accessible with the
FNEK.
This is a minimalistic patch which prevents the FNEKs signatures from
being copied to the inode signatures list. Ultimately, it keeps the FEK
from being encrypted with a FNEK.
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Acked-by: Dustin Kirkland <kirkland@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Fri, 13 Mar 2009 20:51:58 +0000 (13:51 -0700)]
nommu: ramfs: don't leak pages when adding to page cache fails
When a ramfs nommu mapping is expanded, contiguous pages are allocated
and added to the pagecache. The caller's reference is then passed on
by moving whole pagevecs to the file lru list.
If the page cache adding fails, make sure that the error path also
moves the pagevec contents which might still contain up to PAGEVEC_SIZE
successfully added pages, of which we would leak references otherwise.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Enrik Berkhan <Enrik.Berkhan@ge.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enrik Berkhan [Fri, 13 Mar 2009 20:51:56 +0000 (13:51 -0700)]
nommu: ramfs: pages allocated to an inode's pagecache may get wrongly discarded
The pages attached to a ramfs inode's pagecache by truncation from nothing
- as done by SYSV SHM for example - may get discarded under memory
pressure.
The problem is that the pages are not marked dirty. Anything that creates
data in an MMU-based ramfs will cause the pages holding that data will
cause the set_page_dirty() aop to be called.
For the NOMMU-based mmap, set_page_dirty() may be called by write(), but
it won't be called by page-writing faults on writable mmaps, and it isn't
called by ramfs_nommu_expand_for_mapping() when a file is being truncated
from nothing to allocate a contiguous run.
The solution is to mark the pages dirty at the point of allocation by the
truncation code.
Signed-off-by: Enrik Berkhan <Enrik.Berkhan@ge.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dhananjay Phadke [Fri, 6 Mar 2009 14:52:12 +0000 (14:52 +0000)]
netxen: remove old flash check.
Remove flash size check which made sense only for ancient
boards with 1MB flash. The check is based on values read
from specific locations and fails with firmware size changes.
This prevents driver from getting right mac addresses.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lennert Buytenhek [Fri, 13 Mar 2009 22:48:02 +0000 (15:48 -0700)]
mv643xx_eth: fix unicast address filter corruption on mtu change
When mv643xx_eth_open() is called to up an interface, port_start()
will first re-program the unicast address filter, and then
re-initialise the PORT_CONFIG register, but that will disable unicast
promiscuous mode if it was enabled by the unicast address filter setup.
This isn't a problem on ifconfig up, as ->set_rx_mode() will be called
shortly afterwards which will program the filters again, but it does
trigger when changing the MTU, which calls mv643xx_eth_stop() and then
mv643xx_eth_open() by hand to repopulate the receive rings with skbuffs
of the new size.
Swap the initialisation of the PORT_START register and the call to
the unicast filter setup function to fix this.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ralf Baechle [Fri, 13 Mar 2009 20:17:57 +0000 (21:17 +0100)]
MIPS: Mark Eins: Fix configuration.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Zhang Le [Thu, 12 Mar 2009 10:00:50 +0000 (18:00 +0800)]
MIPS: Fix TIF_32BIT undefined problem when seccomp is disabled
Signed-off-by: Zhang Le <r0bertz@gentoo.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David S. Miller [Fri, 13 Mar 2009 21:22:40 +0000 (14:22 -0700)]
xfrm: Fix xfrm_state_find() wrt. wildcard source address.
The change to make xfrm_state objects hash on source address
broke the case where such source addresses are wildcarded.
Fix this by doing a two phase lookup, first with fully specified
source address, next using saddr wildcarded.
Reported-by: Nicolas Dichtel <nicolas.dichtel@dev.6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Herrenschmidt [Fri, 13 Mar 2009 20:48:46 +0000 (13:48 -0700)]
emac: Fix clock control for 405EX and 405EXr chips
The EMAC variant in the 405EX and 405EXr chips needs the "440EP" type clock
control workaround to avoid lockups of the Rx side during reset.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Leech [Tue, 10 Mar 2009 16:00:24 +0000 (16:00 +0000)]
ixgbe: fix multiple unicast address support
Multiple unicast address support appears to have been broken with the
change to support net_device_ops. This a regression from 2.6.28 to 2.6.29.
I'm not 100% on whether ndo_set_multicast_list can be NULL after this
or not. If ndo_set_rx_mode is set everything _should_ be using it.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Jones [Fri, 13 Mar 2009 20:37:46 +0000 (13:37 -0700)]
via-velocity: Fix DMA mapping length errors on transmit.
From: Dave Jones <davej@redhat.com>
The dma-debug changes caught that this driver uses the
wrong DMA mapping length when skb_padto() does something.
With suggestions from Eric Dumazet.
Signed-off-by: David S. Miller <davem@davemloft.net>
FUJITA Tomonori [Fri, 13 Mar 2009 20:16:13 +0000 (21:16 +0100)]
ide: save the returned value of dma_map_sg
dma_map_sg could return a value different to 'nents' argument of
dma_map_sg so the ide stack needs to save it for the later usage
(e.g. for_each_sg).
The ide stack also needs to save the original sg_nents value for
pci_unmap_sg.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
[bart: backport to Linus' tree]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Borislav Petkov [Fri, 13 Mar 2009 20:16:12 +0000 (21:16 +0100)]
ide-floppy: do not map dataless cmds to an sg
since it fails the virt_to_page() translation check with DEBUG_VIRTUAL
enabled.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
[bart: backport to Linus' tree]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Tejun Heo [Tue, 3 Mar 2009 04:52:16 +0000 (13:52 +0900)]
ata_piix: add workaround for Samsung DB-P70
Samsung DB-P70 somehow botched the first ICH9 SATA port. The board
doesn't expose the first port but somehow SStatus reports link online
while failing SRST protocol leading to repeated probe failures and
thus long boot delay.
Because the BIOS doesn't carry any identifying DMI information, the
port can't be blacklisted safely. Fortunately, the controller does
have subsystem vendor and ID set. It's unclear whether the subsystem
IDs are used only for the board but it can be safely worked around by
disabling SIDPR access and just using SRST works around the problem.
Even when the workaround is triggered on an unaffected board the only
side effect will be missing SCR access.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Joseph Jang <josephjang@gmail.com>
Reported-by: Jonghyon Sohn <mrsohn@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Stuart MENEFY [Tue, 10 Mar 2009 11:38:13 +0000 (11:38 +0000)]
libata: Keep shadow last_ctl up to date during resets
libata keeps a shadow copy of the ATA CTL register (which is write only),
and only writes to the hardware when the required value doesn't match
the shadow. However this copy wasn't being maintained when performing
reset functions. This could cause problems for the first operation after
a reset when the correct value might not be written to the CTL register.
This problem was observed when hotplugging a drive: the identify command
was being issued with interrupts enabled, when they should have been
disabled.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Mark Lord [Tue, 10 Mar 2009 20:28:51 +0000 (16:28 -0400)]
sata_mv: fix MSI irq race condition
Fix a (rare) race condition in mv_interrupt() when using MSI.
The value of hpriv->main_irq_mask_addr can change on on the fly,
and without this patch we could end up writing back a stale copy
to the hardware.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ron Mercer [Wed, 11 Mar 2009 11:55:43 +0000 (11:55 +0000)]
qlge: bugfix: Pad outbound frames smaller than 60 bytes.
With some asic configurations xmit of frames smaller than 60 bytes may
fail.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ron Mercer [Wed, 11 Mar 2009 11:55:42 +0000 (11:55 +0000)]
qlge: bugfix: Move netif_napi_del() to common call point.
Moving netif_napi_del() up the call chain so it will get called from all
exit points.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ron Mercer [Wed, 11 Mar 2009 11:55:41 +0000 (11:55 +0000)]
qlge: bugfix: Tell hw to strip vlan header.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ron Mercer [Wed, 11 Mar 2009 11:55:40 +0000 (11:55 +0000)]
qlge: bugfix: Increase filter on inbound csum.
Chip does not do UDP checksum when fragmentation occurs.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ilya Yanok [Fri, 13 Mar 2009 16:51:46 +0000 (09:51 -0700)]
dnet: replace obsolete *netif_rx_* functions with *napi_*
*netif_rx_* functions is obsolete and removed in newer kernels so
we need to use corresponding *napi_* functions instead.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matthias Schwarzzot [Tue, 27 Jan 2009 19:29:44 +0000 (16:29 -0300)]
V4L/DVB (10978): Report tuning algorith correctly
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Werner [Tue, 27 Jan 2009 19:09:12 +0000 (16:09 -0300)]
V4L/DVB (10977): STB6100 init fix, the call to stb6100_set_bandwidth needs an argument
in Hz not kHz, and a comment incorrectly says MHz instead of Hz. I
don't know if this caused real problems anywhere
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Igor M. Liplianin [Sun, 9 Nov 2008 14:35:13 +0000 (11:35 -0300)]
V4L/DVB (10976): Bug fix: For legacy applications stv0899 performs search only first time after insmod.
For legacy applications stv0899 performs search only first time after insmod
due to not set DVBFE_ALGO_SEARCH_AGAIN bit
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Manu Abraham [Tue, 27 Jan 2009 14:03:16 +0000 (11:03 -0300)]
V4L/DVB (10975): Bug: Use signed types, Offsets and range can be negative
Code simplification: use in kernel macros
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sigmund Augdal [Mon, 26 Jan 2009 22:08:48 +0000 (19:08 -0300)]
V4L/DVB (10974): Use Diseqc 3/3 mode to send data
Signed-off-by: Sigmund Augdal <sigmund@snap.tv>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Kyle McMartin [Fri, 13 Mar 2009 05:33:34 +0000 (01:33 -0400)]
parisc: update defconfigs
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Kyle McMartin [Tue, 17 Feb 2009 17:42:52 +0000 (12:42 -0500)]
parisc: define x->x mmio accessors
Bloody inconsiderate driver writers...
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Kay Sievers [Mon, 26 Jan 2009 03:53:16 +0000 (03:53 +0000)]
parisc: dino: struct device - replace bus_id with dev_name(), dev_set_name()
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Kyle McMartin [Mon, 16 Feb 2009 08:20:54 +0000 (03:20 -0500)]
parisc: convert cpu_check_affinity to new cpumask api
cpumask arg to the affinity function is now const, sort
that out through the irq_desc implementations.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Kyle McMartin [Mon, 16 Feb 2009 08:05:02 +0000 (03:05 -0500)]
parisc: convert (read|write)bwlq to inlines
Kills the 'value computed but not used' due to
leX_to_cpu.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Kyle McMartin [Mon, 16 Feb 2009 07:53:03 +0000 (02:53 -0500)]
parisc: fix use of new cpumask api in irq.c
cpumask api needs to take a pointer to irq_desc[cpu].affinity
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Mike Travis [Tue, 13 Jan 2009 03:05:25 +0000 (03:05 +0000)]
parisc: update parisc for new irq_desc
Impact: cleanup, update to new cpumask API
Irq_desc.affinity and irq_desc.pending_mask are now cpumask_var_t's
so access to them should be using the new cpumask API.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Grant Grundler [Mon, 1 Dec 2008 07:21:35 +0000 (00:21 -0700)]
parisc: update MAINTAINERS
Signed-off-By: Grant Grundler <grundler@parisc-linux.org>
Reviewed-by: Matthew Wilcox <matthew@wil.cx>
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Grant Grundler [Thu, 29 Jan 2009 05:30:55 +0000 (22:30 -0700)]
parisc: fix wrong assumption about bus->self
Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> posted a patch series
to linux-pci to fix a wrong assumption about pci_bus->self==NULL for
all PCI host bus controllers. While PARISC platforms to not behave
this way, I prefer to have the code consistent across architectures.
The following patch replaces pci_bus->self with pci_bus->parent when
used as a test to check for "root bus controller".
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Helge Deller [Mon, 26 Jan 2009 21:24:38 +0000 (22:24 +0100)]
parisc: fix 64bit build
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Helge Deller [Sun, 18 Jan 2009 17:13:53 +0000 (18:13 +0100)]
parisc: add braces around arguments in assembler macros
Add braces around the macro arguments, else for example
"shl %r1, 5-3, %r2" would not expand to what you would assume.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Helge Deller [Tue, 13 Jan 2009 20:14:51 +0000 (21:14 +0100)]
parisc: fix dev_printk() compile warnings for accessing a device struct
Fix compile warnings:
drivers/scsi/zalon.c: In function `zalon_probe':
drivers/scsi/zalon.c:140: warning: passing arg 1 of `dev_driver_string' from incompatible pointer type
drivers/scsi/zalon.c:140: warning: passing arg 1 of `dev_name' from incompatible pointer type
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Helge Deller [Tue, 13 Jan 2009 19:54:25 +0000 (20:54 +0100)]
parisc: remove unused local out_putf label
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Helge Deller [Tue, 13 Jan 2009 19:52:46 +0000 (20:52 +0100)]
parisc: fix `struct pt_regs' declared inside parameter list warning
Fix those compile warnings:
uaccess.h:244: warning: `struct pt_regs' declared inside parameter list
uaccess.h:244: warning: its scope is only this definition or declaration, which is probably not what you want
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Helge Deller [Tue, 13 Jan 2009 19:51:29 +0000 (20:51 +0100)]
parisc: fix section mismatch warnings
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
James Bottomley [Sat, 10 Jan 2009 00:57:06 +0000 (18:57 -0600)]
parisc: remove klist iterators
commit
11c3b5c3e08f4d855cbef52883c266b9ab9df879
Author: Greg Kroah-Hartman <gregkh@suse.de>
Date: Tue Dec 16 12:24:56 2008 -0800
driver core: move klist_children into private structure
Broke our parisc build pretty badly because we touch the klists directly
in three cases (AGP, SBA and GSC). Although GregKH will revert this
patch, there's no reason we should be using the iterators directly, we
can just move to the standard device_for_each_child() API.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Helge Deller [Tue, 6 Jan 2009 11:57:01 +0000 (12:57 +0100)]
parisc: BUG_ON() cleanup
- convert a few "if (xx) BUG();" to BUG_ON(xx)
- remove a few printk()s, as we get a backtrace with BUG_ON() anyway
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Antti Palosaari [Tue, 10 Mar 2009 16:06:40 +0000 (13:06 -0300)]
V4L/DVB (10972): zl10353: i2c_gate_ctrl bug fix
zl10353 i2c-gate was always closed and due to that devices having tuner
behind i2c-gate were broken. Add module configuration which allows disabling
i2c-gate only when really needed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Linus Torvalds [Fri, 13 Mar 2009 02:39:28 +0000 (19:39 -0700)]
Linus 2.6.29-rc8
Linus Torvalds [Fri, 13 Mar 2009 02:32:51 +0000 (19:32 -0700)]
bitmap: fix end condition in bitmap_find_free_region
Guennadi Liakhovetski noticed that the end condition for the loop in
bitmap_find_free_region() is wrong, and the "return if error" was also
using the wrong conditional that would only trigger if the bitmap was an
exact multiple of the allocation size, which is not necessarily the case
with dma_alloc_from_coherent().
Such a failure would end up in bitmap_find_free_region() accessing
beyond the end of the bitmap.
Reported-by: Guennadi Liakhovetski <lg@denx.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tao Ma [Thu, 12 Mar 2009 00:37:34 +0000 (08:37 +0800)]
ocfs2: Use xs->bucket to set xattr value outside
A long time ago, xs->base is allocated a 4K size and all the contents
in the bucket are copied to the it. Now we use ocfs2_xattr_bucket to
abstract xattr bucket and xs->base is initialized to the start of the
bu_bhs[0]. So xs->base + offset will overflow when the value root is
stored outside the first block.
Then why we can survive the xattr test by now? It is because we always
read the bucket contiguously now and kernel mm allocate continguous
memory for us. We are lucky, but we should fix it. So just get the
right value root as other callers do.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Acked-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Tao Ma [Wed, 11 Mar 2009 22:24:23 +0000 (06:24 +0800)]
ocfs2: Fix a bug found by sparse check.
We need to use le32_to_cpu to test rec->e_cpos in
ocfs2_dinode_insert_check.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Acked-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Tiger Yang [Thu, 5 Mar 2009 03:06:15 +0000 (11:06 +0800)]
ocfs2: tweak to get the maximum inline data size with xattr
Replace max_inline_data with max_inline_data_with_xattr
to ensure it correct when xattr inlined.
Signed-off-by: Tiger Yang <tiger.yang@oracle.com>
Acked-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Tiger Yang [Fri, 6 Mar 2009 02:19:30 +0000 (10:19 +0800)]
ocfs2: reserve xattr block for new directory with inline data
If this is a new directory with inline data, we choose to
reserve the entire inline area for directory contents and
force an external xattr block.
Signed-off-by: Tiger Yang <tiger.yang@oracle.com>
Acked-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Linus Torvalds [Thu, 12 Mar 2009 23:35:26 +0000 (16:35 -0700)]
Merge git://git./linux/kernel/git/sam/kbuild-fixes
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
kbuild: remove unused -r option for module-init-tool depmod
kbuild: fix 'make rpm' when CONFIG_LOCALVERSION_AUTO=y and using SCM tree
kbuild: fix mkspec to cleanup RPM_BUILD_ROOT
kbuild: fix C libary confusion in unifdef.c due to getline()
Linus Torvalds [Thu, 12 Mar 2009 23:34:59 +0000 (16:34 -0700)]
Merge git://git./linux/kernel/git/rusty/linux-2.6-for-linus
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
cpumask: mm_cpumask for accessing the struct mm_struct's cpu_vm_mask.
cpumask: tsk_cpumask for accessing the struct task_struct's cpus_allowed.
Linus Torvalds [Thu, 12 Mar 2009 23:32:36 +0000 (16:32 -0700)]
Merge git://git./linux/kernel/git/pkl/squashfs-linus
* git://git.kernel.org/pub/scm/linux/kernel/git/pkl/squashfs-linus:
Squashfs: Valid filesystems are flagged as bad by the corrupted fs patch
Linus Torvalds [Thu, 12 Mar 2009 23:25:04 +0000 (16:25 -0700)]
Merge branch 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
hwmon: (f75375s) Remove unnecessary and confusing initialization
hwmon: (it87) Properly decode -128 degrees C temperature
hwmon: (lm90) Document support for the MAX6648/6692 chips
hwmon: (abituguru3) Fix I/O error handling
Jody McIntyre [Thu, 12 Mar 2009 21:39:23 +0000 (17:39 -0400)]
trivial: fix bad links in the ext2 and ext3 documentation
Trivial patch to fix bad links in the ext2 and ext3 documentation.
Signed-off-by: Jody McIntyre <scjody@sun.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>