Bluetooth: Handle specific error for SCO connection fallback

Synchronous Connection Complete event can return error "Connection
Rejected due to Limited resources (0x10)".
Handling this error is required for SCO connection fallback. This error
happens when the server tried to accept the connection but failed to
negotiate settings.
This error code has been verified experimentally by sending a T2 request
to a T1 only SCO listener.

Client dump follows :

< HCI Command (0x01|0x0028) plen 17 [hci0] 3.696064
        Handle: 12
        Transmit bandwidth: 8000
        Receive bandwidth: 8000
        Max latency: 13
        Setting: 0x0003
        Retransmission effort: Optimize for link quality (0x02)
        Packet type: 0x0380
> HCI Event (0x0f) plen 4 [hci0] 3.697034
      Setup Synchronous Connection (0x01|0x0028) ncmd 1
        Status: Success (0x00)
> HCI Event (0x2c) plen 17 [hci0] 3.736059
        Status: Connection Rejected due to Limited Resources (0x0d)
        Handle: 0
        Address: xx:xx:xx:xx:xx:AB (OUI 70-F3-95)
        Link type: eSCO (0x02)
        Transmission interval: 0x0c
        Retransmission window: 0x06
        RX packet length: 60
        TX packet length: 60
        Air mode: Transparent (0x03)

Server dump follows :

> HCI Event (0x04) plen 10 [hci0] 4.741513
        Address: xx:xx:xx:xx:xx:D9 (OUI 20-68-9D)
        Class: 0x620100
          Major class: Computer (desktop, notebook, PDA, organizers)
          Minor class: Uncategorized, code for device not assigned
          Networking (LAN, Ad hoc)
          Audio (Speaker, Microphone, Headset)
          Telephony (Cordless telephony, Modem, Headset)
        Link type: eSCO (0x02)
< HCI Command (0x01|0x0029) plen 21 [hci0] 4.743269
        Address: xx:xx:xx:xx:xx:D9 (OUI 20-68-9D)
        Transmit bandwidth: 8000
        Receive bandwidth: 8000
        Max latency: 13
        Setting: 0x0003
        Retransmission effort: Optimize for link quality (0x02)
        Packet type: 0x03c1
> HCI Event (0x0f) plen 4 [hci0] 4.745517
      Accept Synchronous Connection (0x01|0x0029) ncmd 1
        Status: Success (0x00)
> HCI Event (0x2c) plen 17 [hci0] 4.749508
        Status: Connection Rejected due to Limited Resources (0x0d)
        Handle: 0
        Address: xx:xx:xx:xx:xx:D9 (OUI 20-68-9D)
        Link type: eSCO (0x02)
        Transmission interval: 0x0c
        Retransmission window: 0x06
        RX packet length: 60
        TX packet length: 60
        Air mode: Transparent (0x03)

Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Prevent transparent SCO on older devices

Older Bluetooth devices may not support Setup Synchronous Connection or
SCO transparent data. This is indicated by the corresponding LMP feature
bits. It is not possible to know if the adapter support these features
before setting BT_VOICE option since the socket is not bound to an
adapter. An adapter can also be added after the socket is created. The
socket can be bound to an address before adapter is plugged in.

Thus, on a such adapters, if user request BT_VOICE_TRANSPARENT, outgoing
connections fail on connect() and returns -EOPNOTSUPP. Incoming
connections do not fail. However, they should only be allowed depending
on what was specified in Write_Voice_Settings command.

EOPNOTSUPP is choosen because connect() system call is failing after
selecting route but before any connection attempt.

Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Add constants and macro declaration for transparent data

This patch defines constants and macro for transparent data LMP
features. It refers to Bluetooth Core V4.0 specification, Part C, Chap
3.3 which defines LMP feature mask.

Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Parameters for outgoing SCO connections

In order to establish a transparent SCO connection, the correct settings
must be specified in the Setup Synchronous Connection request. For that,
a setting field is added to ACL connection data to set up the desired
parameters. The patch also removes usage of hdev->voice_setting in CVSD
connection and makes use of T2 parameters for transparent data.

Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Use voice setting in deferred SCO connection request

When an incoming eSCO connection is requested, check the selected voice
setting and reply appropriately. Voice setting should have been
negotiated previously.  For example, in case of HFP, the codec is
negotiated using AT commands on the RFCOMM channel. This patch only
changes replies for socket with deferred setup enabled.

Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Add constants for SCO airmode

This patch defines constants for SCO airmode from SCO voice setting. It
refers to Bluetooth Core V4.0 specification, Part E, Chap 6.12 which
describe SCO voice setting format.

Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Add Bluetooth socket voice option

This patch extends the current Bluetooth socket options with BT_VOICE.
This is intended to choose voice data type at runtime. It only applies
to SCO sockets. Incoming connections shall be setup during deferred
setup. Outgoing connections shall be setup before connect(). The desired
setting is stored in the SCO socket info. This patch declares needed
members, modifies getsockopt() and setsockopt().

Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Remove unused mask parameter in sco_conn_defer_accept

From Bluetooth Core v4.0 specification, 7.1.8 Accept Connection Request
Command "When accepting synchronous connection request, the Role
parameter is not used and will be ignored by the BR/EDR Controller."

Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Use hci_connect_sco directly

hci_connect is a super function for connecting hci protocols. But the
voice_setting parameter (introduced in subsequent patches) is only
needed by SCO and security requirements are not needed for SCO channels.
Thus, it makes sense to have a separate function for SCO.

Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Purge the dlc->tx_queue to avoid circular dependency

In rfcomm_tty_cleanup we purge the dlc->tx_queue which may contain
socket buffers referencing the tty_port and thus preventing the tty_port
destruction.

Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix the reference counting of tty_port

The tty_port can be released in two cases: when we get a HUP in the
functions rfcomm_tty_hangup() and rfcomm_dev_state_change(). Or when the
user releases the device in rfcomm_release_dev().

In these cases we set the flag RFCOMM_TTY_RELEASED so that no other
function can get a reference to the tty_port.
The use of !test_and_set_bit(RFCOMM_TTY_RELEASED) ensures that the
'initial' tty_port reference is only dropped once.

The rfcomm_dev_del function is removed becase it isn't used anymore.

Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Implement .activate, .shutdown and .carrier_raised methods

Implement .activate, .shutdown and .carrier_raised methods of tty_port
to manage the dlc, moving the code from rfcomm_tty_install() and
rfcomm_tty_cleanup() functions.

At the same time the tty .open()/.close() and .hangup() methods are
changed to use the tty_port helpers that properly call the
aforementioned tty_port methods.

Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Move the tty initialization and cleanup out of open/close

Move the tty_struct initialization from rfcomm_tty_open() to
rfcomm_tty_install() and do the same for the cleanup moving the code from
rfcomm_tty_close() to rfcomm_tty_cleanup().

Add also extra error handling in rfcomm_tty_install() because, unlike
.open()/.close(), .cleanup() is not called if .install() fails.

Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Remove the device from the list in the destructor

The current code removes the device from the device list in several
places. Do it only in the destructor instead and in the error path of
rfcomm_add_dev() if the device couldn't be initialized.

Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Take proper tty_struct references

In net/bluetooth/rfcomm/tty.c the struct tty_struct is used without
taking references. This may lead to a use-after-free of the rfcomm tty.

Fix this by taking references properly, using the tty_port_* helpers
when possible.

The raw assignments of dev->port.tty in rfcomm_tty_open/close are
addressed in the later commit 'rfcomm: Implement .activate, .shutdown
and .carrier_raised methods'.

Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Set different event mask for LE-only controllers

In case of a Low Energy only controller it makes no sense to configure
the full BR/EDR event mask. It will just enable events that can not be
send anyway and there is no guarantee that such a controller will accept
this value.

Use event mask 0x90 0xe8 0x04 0x02 0x00 0x80 0x00 0x20 for LE-only
controllers which enables the following events:

          Disconnection Complete
          Encryption Change
          Read Remote Version Information Complete
          Command Complete
          Command Status
          Hardware Error
          Number of Completed Packets
          Data Buffer Overflow
          Encryption Key Refresh Complete
          LE Meta

This is according to Core Specification, Part E, Section 3.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix getting SCO socket options in deferred state

When a socket is in deferred state there does actually exist an
underlying connection even though the connection state is not yet
BT_CONNECTED. In the deferred state it should therefore be allowed to
get socket options that usually depend on a connection, such as
SCO_OPTIONS and SCO_CONNINFO.

This patch fixes the behavior of some user space code that behaves as
follows without it:

$ sudo tools/btiotest -i 00:1B:DC:xx:xx:xx -d -s
accept=2 reject=-1 discon=-1 defer=1 sec=0 update_sec=0 prio=0 voice=0x0000
Listening for SCO connections
bt_io_get(OPT_DEST): getsockopt(SCO_OPTIONS): Transport endpoint is not connected (107)
Accepting connection
Successfully connected to 60:D8:19:xx:xx:xx. handle=43, class=000000

The conditions that the patch updates the if-statements to is taken from
similar code in l2cap_sock.c which correctly handles the deferred state.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: use DIV_ROUND_UP in suitable places in btmrvl_sdio

There are two places where DIV_ROUND_UP may be used. It makes code a bit
clearer.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: replace strict_strtol() with kstrtol()

The usage of strict_strtol() is not preferred, because
strict_strtol() is obsolete. Thus, kstrtol() should be
used.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: hidp: remove wrong send_report at init

The USB hid implementation does retrieve the reports during the start.
However, this implementation does not call the HID command GET_REPORT
(which would fetch the current status of each report), but use the
DATA command, which is an Output Report (so transmitting data from the
host to the device).
The Wiimote controller is already guarded against this problem in the
protocol, but it is not conformant to the specification to set all the
reports to 0 on start.

Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: hidp: implement hidinput_input_event callback

We can re-enable hidinput_input_event to allow the leds of bluetooth
keyboards to be set.
Now the callbacks uses hid core to retrieve the right HID report to
send, so this version is safer.

Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Add missing braces to an "else if"

Trivial change in the coding style.

Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Use defines instead of integer literals

Replace the occurrences of integer literals in hci_event.c with the
newly introduced macros in hci.h.

Signed-off-by: Mikel Astiz <mikel.astiz@bmw-carit.de>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Use defines in in hci_get_auth_req()

Make the code in hci_get_auth_req() more readable by using the
defined macros instead of inlining magic numbers.

Signed-off-by: Mikel Astiz <mikel.astiz@bmw-carit.de>
Signed-off-by: Timo Mueller <timo.mueller@bmw-carit.de>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Add HCI authentication capabilities macros

Add macros for the HCI capabilities as described in the Bluetooth Core
Specification v4.0, Volume 2, part E, section 7.1.29.

Signed-off-by: Mikel Astiz <mikel.astiz@bmw-carit.de>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix simple whitespace vs tab style issue

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

bgmac: make bgmac depend on bcm47xx

bgmac uses bcm47xx_nvram.h which is only available when BCM47XX was
selected. Earlier BCMA_HOST_SOC depended on BCM47XX so this was not
build on any other archs, but that changed. We should modify this
driver to get access to the nvram or the variables through platform
data.

This fixes a build problem in linux-next reported by Stephen Rothwell:

drivers/net/ethernet/broadcom/bgmac.c:19:27: fatal error: bcm47xx_nvram.h: No such file or directory
 #include <bcm47xx_nvram.h>
                           ^

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: rt2x00: rt2800usb: add RT3573 devices

taken from Ralink linux and windows drivers:

0x1b75, 0x7733 AirLive 450Mbps Wireless-N Dual Band USB Adapter
0x0b05, 0x17bc ASUS USB-N66 450Mbps Dual Band USB Adapter
0x0b05, 0x17ad ASUS USB-N66 Dual Band N Network Adapter
0x050d, 0x1103 Belkin Wireless Adapter
0x148f, 0xf301 Cameo Ralink3573 3x3 single band USB dongle
0x7392, 0x7733 Edimax
0x0e66, 0x0020 Hawking HD45U Dual Band USB Wireless-N Adapter
0x0e66, 0x0021 Hawking HD45U Dual Band Wls-450N Adapter
0x04bb, 0x094e I-O DATA WN-AG450U Wireless LAN Adapter
0x0789, 0x016b Logitec LAN-W450AN/U2
0x0846, 0x9012 NETGEAR WNDA4100 N900 Wireless Dual Band USB Adapter
0x0846, 0x9019 NETGEAR WNDA4200D Wireless Dual Band USB Adapter
0x2019, 0xed19 Planex GW-USDual450
0x148f, 0x3573 Ralink 802.11n USB Wireless LAN Card
0x0df6, 0x0067 Sitecom Wireless Dualband Network Adapter N750 X6
0x0df6, 0x006a Sitecom Wireless Dualband Network Adapter N900 X7
0x0586, 0x3421 ZyXEL Dual-Band Wireless N450 USB Adapter

Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: users@rt2x00.serialmonkey.com
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix diversity combining for AR9285

When antenna diversity combining is enabled in the EEPROM,
the initial values for the MAIN/ALT config have to be
programmed correctly. This patch adds it for AR9285.

Since the diversity combining macros are common to all chip
families, remove the redundant AR9285 macros and move the
definitions to phy.h.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: modify mwifiex_ap_sta_limits to advertise support for P2P

We support maximum simultaneous 2 non-AP station interfaces and
they can assume role of Station/P2P client/P2P GO.
Advertise this support to cfg80211 so that concurrent P2P/STA
operation is possible.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: remove duplicate structure host_cmd_tlv

We already have 'struct mwifiex_ie_types_header' with same
definition. Hence host_cmd_tlv is removed in this patch.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: correction in mwifiex_check_fw_status() return status

For PCIe cards, when wrong firmware is downloaded, firmware is
failed to be ready in 10 seconds. We should return an error at
this point. But currently we are sending first command to firmware.
As expected firmware doesn't respond to this command and command
timeout occurs.

This patch fixes the problem by removing unnecessary 'ret'
variable modifications in "if (ret) {" block.
The block is just supposed to update "adapter->winner" flag.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: replace mdelay with msleep

It is observed that when wrong firmware is downloaded for
PCIe card, system hangs for 10 seconds. The reason is mdelay()
is used when firmware status is polled.

Replace mdelay with msleep(non-blocking API) to fix the issue.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: reduce firmware poll retries

After downloading the firmware, firmware status is checked by
reading a register. Polling interval is 100 msecs. Therefore 100
retries means the status is checked for 10 secs which is more than
sufficient for firmware to get ready.

This patch removes 1000 retries macro usage, because 100secs
time is not practical.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: add unregister_dev handler for usb interface

Clear the data pointer stored in USB interface structure in
this handler. This helps to return from mwifiex_usb_disconnect()
if driver deinitialization is already performed while handling
an error path for mwifiex_usb_probe().

USB8797 card gets enumerated twice. First enumeration is for
firmware download and second enumeration expects firmware
initialization. mwifiex_usb_probe() always takes care of
deinitialization for first enumeration after firmware download.

Also, this change matches our handling for SDIO and PCIe
interfaces.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: move if_ops.cleanup_if() call

As if_ops.init_if() is called in mwifiex_register(),
corresponding cleanup routine should be called in
mwifiex_unregister().

Currently it's there in mwifiex_adapter_cleanup(), hence
interface specific cleanup is not performed if driver
initialization is failed.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: remove unnecessary del_timer(cmd_timer)

It is already there in mwifiex_unregister(). So unnecessary
call in mwifiex_adapter_cleanup() is removed in this patch.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: move del_timer_sync(scan_delay_timer) call to fix memleak

Currently it is in mwifiex_adapter_cleanup() which doesn't get
called if driver initialization is failed causing memory leak.

scan_delay_timer is initialized in mwifiex_register(), so it
should be deleted in mwifiex_unregister(). Hence it has been
moved to appropriate place.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: add PCIe shutdown handler to avoid system hang on reboot

If reboot command is issued when device is in connected state,
system hangs while booting. This issue is fixed by doing cleanup
in shutdown handler.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: correct max IE length check for WPS IE

This patch is bug fix for an invalid boundry check for WPS IE.
We should check max IE length against defined macro; instead we were
checking it against size of pointer. Fix it.
Also move IE length check before allocation of memory.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: support to send deauth for P2P client

During P2P handshake, P2P client needs to send deauth after EAPOL
FAILURE to GO. We need add bss mode for P2P client when handle deauth
request.

Without this change, deauth can not be sent out from P2P client side.

Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: skip registering mgmt frame that has already registered

Before sending command to firmware, we need to check the frame type.
We skip registering the mgmt frame that has already been registered.

Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: discard deauth and disassoc event during WPS session

Some GO will send deauth or disassoc packet at the end of WPS
handshake, which causes P2P connecion failure due to the race
condition between event path and data path.

Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: add tx info to skb when forming mgmt frame

In function 'mwifiex_write_data_complete' it need tx info to find
the mwifiex_private to updates statistics and wake up tx queues.
Or we may trigger tx queues timeout when transmitting lots of mgmt
frames.

Signed-off-by: Huawei Yang <harvey.huawei.yang@gmail.com>
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: delete AP TX queues when bridged packets reach threshold

Delete packets from TX queues for this mwifiex_private structure
when bridged packet count reaches maximum threshold. Bridged packets
from each RA List are deleted till they fall to low threshold of 128.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: maintain outstanding packet count for RA list instead of packet size

Maintain total outstanding packet count for RA list instead of total
outstanding size as packet count metric seems more reasonable for
checking threshold etc.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: rename pkt_count to ba_pkt_count in mwifiex_ra_list_tbl struct

pkt_count is used to determine if BA can be formed on this RA list
by comparing it with randomly generated BA threshold. The pkt_count
variable name here is ambiguous and does not reflect its usage
correctly. Rename it to ba_pkt_count.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: remove stop_net_dev_queue operation in AP forwarding

Under uAP mode mwifiex may stop all net tx queues on forwarding
packets. This may stop some tx queues and they never have chance
to be waked up. There is also no need to check tx_pending and
stop queues here. Because local host has such kind of check when
transmitting packets and it's not proper to have forwarding affect
local transmitting.

Signed-off-by: Huawei Yang <harvey.huawei.yang@gmail.com>
Reviewed-by: Avinash Patil <patila@marvell.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: better skb management in rx path

Steinar reported reallocations of skb->head with IPv6, leading to
a warning in skb_try_coalesce()

It turns out iwl3945 has several problems :

1) skb->truesize is underestimated.
   We really consume PAGE_SIZE bytes for a fragment,
   not the frame length.
2) 128 bytes of initial headroom is a bit low and forces reallocations.
3) We can avoid consuming a full page for small enough frames.

Reported-by: Steinar H. Gunderson <sesse@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paul Stewart <pstew@google.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: drop -Werror compiler flag

In production code, don't use -Werror,
as it causes random compilation failures due to compiler version and options used.

With every new version of gcc, it becomes stricter and report more warnings.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

MAINTAINERS: update ath6kl git location

The git tree is in github.com nowadays.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

MAINTAINERS: add ath10k

I forgot to add an entry to MAINTAINERS when submitting the driver.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: Enable TCP/UDP checksum HW offload

Add support for TCP and UDP HW checksum offloading.
RX chain is allways configured for offload mode.
In case of checksum error in RX path the DMA L4 error bit(5)
will be set to 1 and driver will drop the packet.
TX checksum offloading is configrable (ethtool -K).
TX descriptors are configured for checksum offload according
to the SKB protocol type (TCP/UDP, IPV4/6), Upon mismatch drop
the TX packet (checksum required but not TCP/UDP IPV4/6 type).

Signed-off-by: Kirshenbaum Erez <erezk@wilocity.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: fix error path in wil_tx_vring

Release fragments in the order of allocation; including one for skb head

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cw1200: Fix incorrect endianness annotation in a header field

Note that the driver doesn't directly use this field, but it should be
correctly defined in any case.

Signed-off-by: Solomon Peachy <pizza@shaftnet.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Release the RF bus after setting board values

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Program correct initvals for FCC

* CUS217 specific initvals have to be programmed.
* iniAdditional is not used for AR9462/AR9565, remove it.
* Handle channel 2484 for regulatory compliance.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Use correct channel when switching bands

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix FastChannelChange for AR9462/AR9565

Right now, even though these chips support cross-band
FCC, the code is non-functional since we bail out early if
the channelFlags differ. Fix this so that cross-band
FCC works for cards that support this feature.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Add a HW flag for FCC

Fast Channel Change across 2G/5G bands is supported
only by AR9462 and AR9565. Add a HW capability field
to indicate this.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Move INI overrides to ar9003_hw_override_ini

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmsmac: Further reduce log spam from tx phy messages

Relegate 2 phy messages to debug status as they create excessive
log spam, noted in multiple bugzillas for brcmsmac v3.8 and up.
This is a follow on to net-next 99e94940697adec4f84758adb2db71f4a82c7ba5:
brcmsmac: Reduce log spam in heavy tx, make err print in debug

 brcmsmac bcma0:0: phyerr 0x10, rate 0x14
 brcmsmac bcma0:0: brcms_c_ampdu_dotxstatus_complete:
ampdu tx phy error (0x10)

Signed-off-by: John Greene <jogreene@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: fix handling of big addrl

The return value of bcma_erom_get_addr_desc() is a unsigned value and it
could wrap around in the two complement writing. This happens for one
core in the BCM4708 SoC.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: return correct error code when bus scan failed

It is better to return the actual error code than just -1.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: add constants for new ARM based SoCs

These are the chipIDs of some ARM based SoCs from the BCM47xx line.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: make it possible to select SoC support without mips

To make it possible to use the SoC host interface with ARM SoCs do not
depend on the MIPS driver any more.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bcma: add some more core names

These cores were found on a BCM4708 (chipid 53010), this is a ARM SoC
with two Cortex A9 cores.

bcma: bus0: Found chip with id 0xCF12, rev 0x00 and package 0x02
bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x2A, class 0x0)
bcma: bus0: Core 1 found: DMA (manuf 0x4BF, id 0x502, rev 0x01, class 0x0)
bcma: bus0: Core 2 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x04, class 0x0)
bcma: bus0: Core 3 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x04, class 0x0)
bcma: bus0: Core 4 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x04, class 0x0)
bcma: bus0: Core 5 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x04, class 0x0)
bcma: bus0: Core 6 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x01, class 0x0)
bcma: bus0: Core 7 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x01, class 0x0)
bcma: bus0: Core 8 found: ARM Cortex A9 core (ihost) (manuf 0x4BF, id 0x510, rev 0x01, class 0x0)
bcma: bus0: Core 9 found: USB 2.0 (manuf 0x4BF, id 0x504, rev 0x01, class 0x0)
bcma: bus0: Core 10 found: USB 3.0 (manuf 0x4BF, id 0x505, rev 0x01, class 0x0)
bcma: bus0: Core 11 found: SDIO3 (manuf 0x4BF, id 0x503, rev 0x01, class 0x0)
bcma: bus0: Core 12 found: ARM Cortex A9 JTAG (manuf 0x4BF, id 0x506, rev 0x01, class 0x0)
bcma: bus0: Core 13 found: Denali DDR2/DDR3 memory controller (manuf 0x4BF, id 0x507, rev 0x01, class 0x0)
bcma: bus0: Core 14 found: ROM (manuf 0x4BF, id 0x508, rev 0x01, class 0x0)
bcma: bus0: Core 15 found: NAND flash controller (manuf 0x4BF, id 0x509, rev 0x01, class 0x0)
bcma: bus0: Core 16 found: SPI flash controller (manuf 0x4BF, id 0x50A, rev 0x01, class 0x0)

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: fix subtle race in wil_tx_vring

Finish all SW context modifications prior to notifying hardware

It used to be race condition: if HW finish Tx and issue Tx completion IRQ very fast,
prior to SW context update in wil_tx_vring, Tx completion will mis-handle descriptor, as
SW part will have no skb pointer stored.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: Introduce struct for sw context

Enable adding more data to the SW context.
For now, add flag "mapped_as_page", to separate decisions on free-ing skb
and type of DMA mapping.
This allows linking skb itself to any descriptor of fragmented skb.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: Optimize Tx completion

No need to modify HW descriptor, as it will be re-initialized on Tx.

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: fix wrong index in wil_vring_free

When destroying Rx vring, branch for Rx used wrong Tx descriptor:
while SW context was taken for "head", HW descriptor was, by mistake,
taken from "tail"

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wil6210: Align WMI header with latest FW

FW guys changed header structure; align driver code

Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800usb: add USB device ID for Linksys AE3000

The Linksys AE3000 device is based on the RT3573
chipset. The support for this chipset is available
already, and the AE3000 device works with the driver.

Only managed mode works correctly at the moment,
for AP mode additional changes are needed in the
driver.

Also add a new RT2800USB_RT3573 Kconfig option and
only enable support for RT3573 based devices if
that is enabled.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800usb: use correct [RT]XWI size for RT3593

The RT3593 chipset requires different [RT]XWI size
values. Modify the driver to use the correct values.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: enable RT3593 support

Support for the RT3593 has been implemented in
the previous changes, so it is safe to mark it
supported in the driver.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: enable RF3053 support

Support for the RF3053 has been implemented in
the previous changes, so it is safe to mark it
supported in the driver.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: enable VCO recalibration for RF3053

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: add channel configuration for RF3053

Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

Reference:
  RT3593_ChipSwitchChannel in chips/rt3593.c

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: add rf_vals for RF3053

Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

References:
  FreqItems3053 in chips/rt3593.c

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: add default_power3 field for three-chain devices

The actual code uses two default TX power values.
This is enough for 1T and for 2T devices however
on 3T devices another value is needed for the third
chain.

Add a new field to struct channel_info and initialize
it from the 'rt2800_probe_hw_mode' function. Also modify
the 'rt2800_config_channel' to handle the new field as
well.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: fix LNA_A[12] gain values for RT3593

The LNA_A[12] gain values are stored at a different
offset in the EEPROM on RT3593 based devices. However
the current code unconditionally reads those values
from the location used by other chipsets.

Fix the code to use the correct EEPROM offset.

Based on the DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

References:
  RT3593_EEPROM_RSSI2_OFFSET_ALNAGAIN1_24G_READ in include/chip/rt3593.h
  RT3593_EEPROM_RSSI2_OFFSET_ALNAGAIN2_5G_READ in include/chip/rt3593.h

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: hardcode TX mixer gain values for RT3593

The reference code uses hardcoded zero TX mixer gain value
for RT3593. Do the same in the rt2x00 driver.

Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

Reference:
  NICReadEEPROMParameters in common/rtmp_init.c

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: introduce rt2800_get_txmixer_gain_{24,5}g helpers

Move the TX mixer gain reading code into separate
helper functions in preparation for RT3593 support.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: fix default TX power values for RT3593

The TX power values in the EEPROM are using
a different format for the RT3593 chip. The
default TX power value uses bits 0..4 only.
Bits 5..8 contains value for fine grained
power control. Additionally, the lower and
upper limits of the TX power values are the
same for both bands.

Improve the rt2800_txpower_to_dev function,
in order to compute the correct default power
values for the RT3593 chip as well.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: add rt2800_txpower_to_dev helper

Introduce a new helper function for converting
the default TX power values from EEPROM into
mac80211 values.

The change improves the readability and it makes
it easier to add support for other chipsets.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: fix antenna configuration for RT3593

On the RT3593 chipset, BBP register 86 must be
configured by different values based on the RX
antenna numbers.

Configure this register from the 'rt2800_config_ant'
function.

Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

Reference:
  RT3593_CONFIG_SET_BY_ANTENNA in include/chip/rt3593.h

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: fix BBP1_TX_ANTENNA field configuration for 3T devices

The field must be set to 2 instead of 0 for
devices with three TX chains.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: add TX power configuration for RT3593

Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

References:
  RTMPReadTxPwrPerRateExt in chips/rt3593.c
  RT3593_AsicGetTxPowerOffset in chips/rt3593.c

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: add BBP post initialization for RT3593

Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

Reference:
  RT3593_PostBBPInitialization in chips/rt3553.c

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: add RFCSR register initialization for RT3593

Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

References:
  NICInitRT3593RFRegisters in chips/rt3593.c
  RT3593LoadRFNormalModeSetup in chips/rt3593.c

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: add BBP register initialization for RT3593

Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

References:
  NICInitRT3593BbpRegisters in chips/rt3593.c
  NICInitBBP in common/rtmp_init.c
  NICInitAsicFromEEPROM in common/rtmp_init.c

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: add MAC register initialization for RT3593

Based on the Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

Reference:
  NICInitRT3593MacRegisters in chips/rt3593.c

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: add EEPROM map for the RT3593 chipset

Three-chain devices are using a different
EEPROM layout than the rest of the chipsets.
Add a new map which describes the new layout
and use that for the RT3593 chipset.

The index values has been computed from the
EEPROM_EXT_* defines, which can be found in
the 'include/chip/rt3593.h' file in the
Ralink DPO_RT5572_LinuxSTA_2.6.0.1_20120629
driver.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: introduce rt2800_eeprom_word_index helper

Instead of assign the offset value to the
enum directly use a new helper function to
convert a rt2800_eeprom_word enum into an
index of the rt2x00_dev->eeprom array.

The patch does not change the existing
behaviour, but makes it possible to add
support for three-chain devices which are
using a different EEPROM layout.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: introduce rt2800_eeprom_read_from_array helper

Add a new helper function and use that for reading
single elements of various arrays in the EEPROM.

The patch does not change the current behaviour,
but it allows to use sequential values for the
rt2800_eeprom_word enums. The conversion will be
implemented in a subsequent change.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: introduce local EEPROM access functions

The patch adds rt2800 specific functions for
EEPROM data access and changes the code to use
these instead of the generic rt2x00_eeprom_*
variants.

To avoid functional changes, the new functions
are wrappers around the corresponding generic
rt2x00_eeprom_* routines for now. Functional
changes will be implemented in additional patches.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: rt2800lib: introduce rt2800_eeprom_word enum

The patch converts the EEPROM_* word address defines
into new enum values. The new enum type will be used
by new functions which will be introduced in subsequent
changes.

The patch contains no functional changes.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix RTS threshold

Currently, RTS threshold is not handled for HT. Handle
user-specified threshold values for both aggregated
and unaggregated frames. Use the wiphy's threshold
parameter for now, it can be made per-VIF later on.

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: make rfkill configurable

When the platform doesn't have rfkill support, i.e. nothing
is connected to the rfkill GPIO, there's little value in
polling the GPIO. Add a Kconfig option to allow disabling
the polling in ath9k.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: Convert mwifiex/pcie to dev_pm_ops from legacy pm_ops

Convert the mwifiex/pci driver to use dev_pm_ops for power management and
remove Legacy PM handling. This change re-uses existing suspend and resume
interfaces for dev_pm_ops, and changes CONFIG_PM ifdefs to CONFIG_PM_SLEEP
as the driver does not support run-time PM.

Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>