Andrzej Hajda [Wed, 1 Feb 2017 07:47:44 +0000 (08:47 +0100)]
drm/bridge/sii8620: split EDID read and write code
MHL3 requires that after reading EDID from the sink source should ask
peer for features. To make both protocols happy the patch splits the code
accordingly.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-18-git-send-email-a.hajda@samsung.com
Andrzej Hajda [Wed, 1 Feb 2017 07:47:43 +0000 (08:47 +0100)]
drm/bridge/sii8620: add delay during cbus reset
Without delay CBUS sometimes was not reset properly.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-17-git-send-email-a.hajda@samsung.com
Andrzej Hajda [Wed, 1 Feb 2017 07:47:42 +0000 (08:47 +0100)]
drm/bridge/sii8620: do not stop MHL output when TMDS input is stopped
Stopping output causes full re-detection of the sink and slows down the
process.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-16-git-send-email-a.hajda@samsung.com
Andrzej Hajda [Wed, 1 Feb 2017 07:47:41 +0000 (08:47 +0100)]
drm/bridge/sii8620: set gen2 write burst before sending MSC command
Write burst should be enabled for MHL_INT_RC_FEAT_REQ and disabled for
other commands. The patch moves functions up and adds delay setting
for MHL3 burst mode.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-15-git-send-email-a.hajda@samsung.com
Andrzej Hajda [Wed, 1 Feb 2017 07:47:40 +0000 (08:47 +0100)]
drm/bridge/sii8620: abstract out sink detection code
MHL1 and MHL3 have different initialization paths. To make both protocols
happy sink detection is put into continuation after link mode enablement.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-14-git-send-email-a.hajda@samsung.com
Andrzej Hajda [Wed, 1 Feb 2017 07:47:39 +0000 (08:47 +0100)]
drm/bridge/sii8620: fix initialization sequence for MHL2 receivers
MHL2 receiver require disabling transmitter on initialization.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-13-git-send-email-a.hajda@samsung.com
Andrzej Hajda [Wed, 1 Feb 2017 07:47:38 +0000 (08:47 +0100)]
drm/bridge/sii8620: fix MSC message removal
Messages queue can be cleaned up by message callbacks, to avoid repeated
removal of current message it should be removed from the queue before
calling these callbacks.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-12-git-send-email-a.hajda@samsung.com
Andrzej Hajda [Wed, 1 Feb 2017 07:47:37 +0000 (08:47 +0100)]
drm/bridge/sii8620: remove spare CBUS bring-up sequence
In case of MHL3 CBUS is bring-up already in sii8620_got_ecbus_speed.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-11-git-send-email-a.hajda@samsung.com
Andrzej Hajda [Wed, 1 Feb 2017 07:47:36 +0000 (08:47 +0100)]
drm/bridge/sii8620: fix peer device capabilities read code
Peer capabilities should be read differently depending on protocol version.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-10-git-send-email-a.hajda@samsung.com
Andrzej Hajda [Wed, 1 Feb 2017 07:47:35 +0000 (08:47 +0100)]
drm/bridge/sii8620: respond to feature requests
MHL3 protocol requires device to respond to feature request from peer.
This minimal answer fulfills the requirement and allows to continue
negotiation.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-9-git-send-email-a.hajda@samsung.com
Andrzej Hajda [Wed, 1 Feb 2017 07:47:34 +0000 (08:47 +0100)]
drm/bridge/sii8620: add support for burst eMSC transmissions
Burst transmissions are used in MHL3 mode negotiation.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-8-git-send-email-a.hajda@samsung.com
Andrzej Hajda [Wed, 1 Feb 2017 07:47:33 +0000 (08:47 +0100)]
drm/bridge/mhl: add write burst related definitions
Burst transmissions are required in MHL3 modes.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-7-git-send-email-a.hajda@samsung.com
Andrzej Hajda [Wed, 1 Feb 2017 07:47:32 +0000 (08:47 +0100)]
drm/bridge/sii8620: initial support for eCBUS-S mode
The Single-ended eCBUS Mode (eCBUS-S) mode provides 60 Mb/s full-duplex
bidirectional traffic for three channels:
- CBUS data (CBUS1 channel),
- High-bandwidth MHL data (eMSC channel),
- tunneling data (T-CBUS channel).
It is required to fully support MHL3 dongles.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-6-git-send-email-a.hajda@samsung.com
Andrzej Hajda [Wed, 1 Feb 2017 07:47:31 +0000 (08:47 +0100)]
drm/bridge/sii8620: add continuations to messages
Due to asynchronous nature of MHL flow of execution is dispersed.
Logical continuation of some actions happens after response of peer,
i.e in interrupt handler. To simplify coding continuation mechanism
has been added - it is now possible to provide continuation callback,
which will be called after peer responds to given action.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-5-git-send-email-a.hajda@samsung.com
Andrzej Hajda [Wed, 1 Feb 2017 07:47:30 +0000 (08:47 +0100)]
drm/bridge/sii8620: add reading device capability registers
This functionality is necessary to implement MHL3 modes.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-4-git-send-email-a.hajda@samsung.com
Andrzej Hajda [Wed, 1 Feb 2017 07:47:29 +0000 (08:47 +0100)]
drm/bridge/sii8620: add MHL3 mode check helper
MHL3 modes differs significantly from MHL1 mode, this helper will be used
frequently to clearly distinguish them.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-3-git-send-email-a.hajda@samsung.com
Andrzej Hajda [Wed, 1 Feb 2017 07:47:28 +0000 (08:47 +0100)]
drm/bridge/sii8620: simplify MHL3 mode setting
It is not necessary to set REG_COC_CTL0, REG_MHL_COC_CTL1 registers.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1485935272-17337-2-git-send-email-a.hajda@samsung.com
Gabriel Krisman Bertazi [Fri, 27 Jan 2017 01:05:48 +0000 (23:05 -0200)]
drm: qxl: Embed drm_device into driver structure
This is the recommended way to create the drm_device structure,
according to DRM documentation.
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170127010548.27970-4-krisman@collabora.co.uk
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Gabriel Krisman Bertazi [Fri, 27 Jan 2017 01:05:47 +0000 (23:05 -0200)]
drm: qxl: Drop duplicated pci_device pointer attribute
qxl_device duplicates the pointer to struct pci_dev, which is not
needed since we already have it in the drm_device structure. Clean it
up.
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170127010548.27970-3-krisman@collabora.co.uk
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Gabriel Krisman Bertazi [Fri, 27 Jan 2017 01:05:46 +0000 (23:05 -0200)]
drm: qxl: Drop duplicated device pointer attribute
qxl_device duplicates a pointer to struct device, which is not needed
since we already have it in the drm_device structure. Clean it up.
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170127010548.27970-2-krisman@collabora.co.uk
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Gabriel Krisman Bertazi [Fri, 27 Jan 2017 01:05:45 +0000 (23:05 -0200)]
drm: qxl: Drop misleading comment
No longer true since commit
07f8d9bdb235 ("drm/qxl: add support for > 1
output"). qxl_num_crtc defaults to 4 and is configurable as a module
parameter.
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170127010548.27970-1-krisman@collabora.co.uk
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Max Staudt [Wed, 18 Jan 2017 18:10:12 +0000 (19:10 +0100)]
drm/bochs: Implement nomodeset
Up until now, the bochsdrm driver didn't handle the nomodeset option
at boot, and didn't provide a "modeset" module option either.
This patch implements both.
The new parameter can be used by specifying bochs-drm.modeset=0
at boot time.
Signed-off-by: Max Staudt <mstaudt@suse.de>
Link: http://patchwork.freedesktop.org/patch/msgid/1484763012-17783-1-git-send-email-mstaudt@suse.de
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: David Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Eric Anholt [Tue, 31 Jan 2017 19:29:11 +0000 (11:29 -0800)]
drm/vc4: Add DSI driver
The DSI0 and DSI1 blocks on the 2835 are related hardware blocks.
Some registers move around, and the featureset is slightly different,
as DSI1 (the 4-lane DSI) is a later version of the hardware block.
This driver doesn't yet enable DSI0, since we don't have any hardware
to test against, but it does put a lot of the register definitions and
code in place.
v2: Use the clk_hw interfaces, don't set CLK_IS_BASIC (from review by
Stephen Boyd)
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/20170131192912.11316-1-eric@anholt.net
Eric Anholt [Wed, 14 Dec 2016 19:46:16 +0000 (11:46 -0800)]
dt-bindings: Document the VC4 DSI module nodes.
These are part of the vc4 display pipeline.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Rob Herring <robh@kernel.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20161214194621.16499-7-eric@anholt.net
Eric Anholt [Wed, 14 Dec 2016 19:46:15 +0000 (11:46 -0800)]
drm/vc4: Add support for feeding DSI encoders from the pixel valve.
We have to set a different pixel format, which tells the hardware to
use the pix_width field that's fed in sideband from the DSI encoder to
divide the "pixel" clock.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161214194621.16499-6-eric@anholt.net
Eric Anholt [Wed, 14 Dec 2016 19:46:14 +0000 (11:46 -0800)]
drm/vc4: Set up SCALER_DISPCTRL at boot.
We want the HVS on, obviously, and we also want DSP3 (PV1's source) to
be muxed from HVS channel 2 like we expect in vc4_crtc.c. The
firmware wasn't setting the DSP3 mux up when both the LCD and HDMI
were disabled.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161214194621.16499-5-eric@anholt.net
Takashi Iwai [Tue, 17 Jan 2017 16:43:29 +0000 (17:43 +0100)]
drm: Clean up the 1366x768 fixup codes
This is just a cleanup, no functional change.
The fixup code for 1366x768 in drm_mode_create_from_cmdline_mode() is
basically a copy of the existing code in drm_edid.c. Make the latter
code public so that it can be called from the former function.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: http://patchwork.freedesktop.org/patch/msgid/20170117164329.10551-1-tiwai@suse.de
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[vsyrjala: include drm_crtc_internal.h to make sparse happy]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Daniel Vetter [Wed, 1 Feb 2017 08:06:26 +0000 (09:06 +0100)]
Merge remote-tracking branch 'airlied/drm-next' into drm-misc-next
Backmerge to resync and also so that Ville can apply a cleanup patch
from Takashi.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Dave Airlie [Tue, 31 Jan 2017 22:43:42 +0000 (08:43 +1000)]
Merge branch 'exynos-drm-next' of git://git./linux/kernel/git/daeinki/drm-exynos into drm-next
adding runtime PM support to MIC driver, and including some
cleanups - especially using atomic helper functions
instead of specific ones - and fixups.
* 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: g2d: prevent integer overflow in
drm/exynos: fix a timeout loop
drm/exynos: use atomic helper commit
drm/exynos: remove unnecessary codes
drm/exynos: mic: Add runtime PM support
drm/exynos: Stop using drm_framebuffer_unregister_private
drm/exynos: mic: Fix parse_dt function
drm/exynos: mic: Add mode_set callback function
Dave Airlie [Tue, 31 Jan 2017 22:43:19 +0000 (08:43 +1000)]
Merge tag 'sunxi-drm-for-4.11' of https://git./linux/kernel/git/mripard/linux into drm-next
Allwinner DRM changes for 4.11
Just one minor fix.
* tag 'sunxi-drm-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
drm/sun4i: Fix a return value in case of error
Dave Airlie [Tue, 31 Jan 2017 22:40:13 +0000 (08:40 +1000)]
Merge branch 'drm-vmwgfx-next' of git://people.freedesktop.org/~syeh/repos_linux into drm-next
This is to address what we've discussed, moving some of the minor changes
into a drm-next request.
* 'drm-vmwgfx-next' of git://people.freedesktop.org/~syeh/repos_linux:
drm/vmwgfx: Use kmemdup instead of kmalloc and memcpy
drm/vmwgfx: Fix depth input into drm_mode_legacy_fb_format
drm/vmwgfx: Fix a potential integer overflow
drm/vmwgfx: Clear an uninitialized struct member
drm/vmwgfx: Annotate ignored return values
drm/vmwgfx: Clear uninitialized fields of a parameter
Dave Airlie [Tue, 31 Jan 2017 22:39:35 +0000 (08:39 +1000)]
Merge branch 'drm-next-4.11' of git://people.freedesktop.org/~agd5f/linux into drm-next
This is the main feature pull for radeon and amdgpu for 4.11. Highlights:
- Power and clockgating improvements
- Preliminary SR-IOV support
- ttm buffer priority support
- ttm eviction fixes
- Removal of the ttm lru callbacks
- Remove SI DPM quirks due to MC firmware issues
- Handle VFCT with multiple vbioses
- Powerplay improvements
- Lots of driver cleanups
* 'drm-next-4.11' of git://people.freedesktop.org/~agd5f/linux: (120 commits)
drm/amdgpu: fix amdgpu_bo_va_mapping flags
drm/amdgpu: access stolen VRAM directly on CZ (v2)
drm/amdgpu: access stolen VRAM directly on KV/KB (v2)
drm/amdgpu: fix kernel panic when dpm disabled on Kv.
drm/amdgpu: fix dpm bug on Kv.
drm/amd/powerplay: fix regresstion issue can't set manual dpm mode.
drm/amdgpu: handle vfct with multiple vbios images
drm/radeon: handle vfct with multiple vbios images
drm/amdgpu: move misc si headers into amdgpu
drm/amdgpu: remove unused header si_reg.h
drm/radeon: drop pitcairn dpm quirks
drm/amdgpu: drop pitcairn dpm quirks
drm: radeon: radeon_ttm: Handle return NULL error from ioremap_nocache
drm/amd/amdgpu/amdgpu_ttm: Handle return NULL error from ioremap_nocache
drm/amdgpu: add new virtual display ID
drm/amd/amdgpu: remove the uncessary parameter for ib scheduler
drm/amdgpu: Bring bo creation in line with radeon driver (v2)
drm/amd/powerplay: fix misspelling in header guard
drm/ttm: revert "add optional LRU removal callback v2"
drm/ttm: revert "implement LRU add callbacks v2"
...
Dave Airlie [Tue, 31 Jan 2017 22:31:09 +0000 (08:31 +1000)]
Merge tag 'drm-misc-next-2017-01-30' of git://anongit.freedesktop.org/git/drm-misc into drm-next
Another round of -misc stuff:
- Noralf debugfs cleanup cleanup (not yet everything, some more driver
patches awaiting acks).
- More doc work.
- edid/infoframe fixes from Ville.
- misc 1-patch fixes all over, as usual
Noralf needs this for his tinydrm pull request.
* tag 'drm-misc-next-2017-01-30' of git://anongit.freedesktop.org/git/drm-misc: (48 commits)
drm/vc4: Remove vc4_debugfs_cleanup()
dma/fence: Export enable-signaling tracepoint for emission by drivers
drm/tilcdc: Remove tilcdc_debugfs_cleanup()
drm/tegra: Remove tegra_debugfs_cleanup()
drm/sti: Remove drm_debugfs_remove_files() calls
drm/radeon: Remove drm_debugfs_remove_files() call
drm/omap: Remove omap_debugfs_cleanup()
drm/hdlcd: Remove hdlcd_debugfs_cleanup()
drm/etnaviv: Remove etnaviv_debugfs_cleanup()
drm/etnaviv: allow build with COMPILE_TEST
drm/amd/amdgpu: Remove drm_debugfs_remove_files() call
drm/prime: Clarify DMA-BUF/GEM Object lifetime
drm/ttm: Make sure BOs being swapped out are cacheable
drm/atomic: Remove drm_atomic_debugfs_cleanup()
drm: drm_minor_register(): Clean up debugfs on failure
drm: debugfs: Remove all files automatically on cleanup
drm/fourcc: add vivante tiled layout format modifiers
drm/edid: Set YQ bits in the AVI infoframe according to CEA-861-F
drm/edid: Set AVI infoframe Q even when QS=0
drm/edid: Introduce drm_hdmi_avi_infoframe_quant_range()
...
Dave Airlie [Tue, 31 Jan 2017 22:30:19 +0000 (08:30 +1000)]
Merge tag 'drm/atmel-hlcdc/for-4.11' of git://git./linux/kernel/git/bbrezillon/linux into drm-next
Contains a single patch to create the fbdev at driver's registration
time instead of waiting for the connector status change.
* tag 'drm/atmel-hlcdc/for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/bbrezillon/linux:
drm/atmel-hlcdc: Rework the fbdev creation logic
Dave Airlie [Tue, 31 Jan 2017 22:26:33 +0000 (08:26 +1000)]
Merge tag 'zxdrm-4.11' of git://git./linux/kernel/git/shawnguo/linux into drm-next
ZTE DRM driver updates for 4.11:
- Add missing selection of VIDEOMODE_HELPERS in Kconfig, since ZTE DRM
driver uses drm_display_mode_to_videomode().
- Enable HDMI audio support through SPDIF interface based on generic
hdmi-audio-codec driver.
- Enable VOU VL (Video Layer) to support overlay plane with scaling
function.
- Refine zx_vou driver a bit and then add TV Encoder output device
support.
[airlied: fixup plane format change]
* tag 'zxdrm-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
drm: zte: add tvenc driver support
dt: add bindings for ZTE tvenc device
drm: zte: add function to configure vou_ctrl dividers
drm: zte: move struct vou_inf into zx_vou driver
drm: zte: add interlace mode support
drm: zte: add overlay plane support
drm: zte: add .atomic_disable hook to disable graphic layer
drm: zte: make zx_plane accessible from zx_vou driver
drm: zte: support hdmi audio through spdif
drm: zte: select VIDEOMODE_HELPERS in Kconfig
Dave Airlie [Tue, 31 Jan 2017 22:26:02 +0000 (08:26 +1000)]
Merge branch 'drm-intel-next' of git://anongit.freedesktop.org/git/drm-intel into drm-next
Updated pull request after I pulled first time :)
* 'drm-intel-next' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: Pevent copying uninitialised garbage into vma->ggtt_view
Dave Airlie [Tue, 31 Jan 2017 22:07:23 +0000 (08:07 +1000)]
Merge branch 'for-upstream/mali-dp' of git://linux-arm.org/linux-ld into drm-next
Hope I'm not too late before the cutoff for the v4.11 with these patches.
Mostly an asorted set of fixes that we have discovered while playing with
the code and preparing for the next set of features.
* 'for-upstream/mali-dp' of git://linux-arm.org/linux-ld:
drm: mali-dp: fix stride setting for multi-plane formats
drm: mali-dp: Add plane offset to the plane's physical start address register
drm: mali-dp: Check for sufficient address space
drm: mali-dp: Check hw version matches device-tree
drm: mali-dp: Rename malidp_input_format to malidp_pixel_format
drm: mali-dp: fix Lx_CONTROL register fields clobber
drm: mali-dp: Fix transposed horizontal/vertical flip
drm: mali-dp: Fix destination size handling when rotating
drm: mali-dp: Don't force source size == crtc size
drm: mali-dp: Check more use cases in the plane's ->atomic_check()
drm: malidp: Remove event_list member from struct malidp_drm
drm/arm/malidp: Fix possible dereference of NULL
Liviu Dudau [Tue, 31 Jan 2017 17:41:09 +0000 (17:41 +0000)]
Documentation/gpu: drm-mm.rst: fix formatting for struct vm_operations_struct
drm-mm.rst contains some unformatted dump of the vm_operations_struct
structure. Add some C formatting around it and some context for the
dump. While there, update the structure to resemble the new signature
for the fault handler after commit
25d3db7600b8 (mm, fs: reduce fault,
page_mkwrite, and pfn_mkwrite to take only vmf).
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170131174109.13690-1-Liviu.Dudau@arm.com
Jani Nikula [Fri, 27 Jan 2017 15:34:51 +0000 (17:34 +0200)]
drm/color: un-inline drm_color_lut_extract()
The function is not that big, but it's also not used for anything
performance critical. Make it a normal function.
As a side effect, this apparently makes sparse smarter about what it's
doing, and gets rid of the warning:
./include/drm/drm_color_mgmt.h:53:28: warning: shift too big (
4294967295) for type unsigned long
./include/drm/drm_color_mgmt.h:53:28: warning: cast truncates bits from constant value (
8000000000000000 becomes 0)
v2: rebased
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485531291-24821-1-git-send-email-jani.nikula@intel.com
Dhinakaran Pandiyan [Tue, 31 Jan 2017 06:18:38 +0000 (22:18 -0800)]
drm/docs: Fix documentation for drm_atomic_set_mode_for_crtc
drm_atomic_set_mode_for_crtc() modifies the .enable member of CRTC state
but documentation claims otherwise, fix that.
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1485843518-28438-1-git-send-email-dhinakaran.pandiyan@intel.com
Laurent Vivier [Tue, 24 Jan 2017 13:12:29 +0000 (14:12 +0100)]
virtio-gpu: disable VIRGL with BE kernel
VIRTIO_GPU_F_VIRGL is added in features list only
for LE kernel, so we must check for it only on LE kernel,
otherwise virtio_has_feature() calls BUG() and
crashes the kernel.
Suggested-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485263549-28743-1-git-send-email-lvivier@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Joonyoung Shim [Mon, 23 Jan 2017 09:13:54 +0000 (18:13 +0900)]
drm/exynos: g2d: prevent integer overflow in
The size computations done in the ioctl function use an integer.
If userspace submits a request with req->cmd_nr or req->cmd_buf_nr
set to INT_MAX, the integer computations overflow later, leading
to potential (kernel) memory corruption.
Prevent this issue by enforcing a limit on the number of submitted
commands, so that we have enough headroom later for the size
computations.
Note that this change has no impact on the currently available
users in userspace, like e.g. libdrm/exynos.
While at it, also make a comment about the size computation more
detailed.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Dan Carpenter [Fri, 20 Jan 2017 16:54:32 +0000 (17:54 +0100)]
drm/exynos: fix a timeout loop
We were trying to print an error message if we timed out here, but the
loop actually ends with "tries" set to UINT_MAX and not zero. Fix this
by changing from tries-- to --tries.
A for loop would actually be the most natural way to do this. My fix
means we only loop 99 times instead of 100 but that's probably ok.
Fixes: a696394c5224 ('drm/exynos: mixer: simplify loop in vp_win_reset()')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Inki Dae [Fri, 20 Jan 2017 03:51:41 +0000 (12:51 +0900)]
drm/exynos: use atomic helper commit
This patch replaces specific atomic commit function
with atomic helper commit one.
For this, it removes existing atomic commit function
and relevant code specific to Exynos DRM and makes
atomic helper commit to be used instead.
Below are changes for the use of atomic helper commit:
- add atomic_commit_tail callback specific to Exynos DRM
. default implemention of atomic helper doesn't mesh well
with runtime PM so the device driver which supports runtime
PM should call drm_atomic_helper_commit_modeset_enables function
prior to drm_atomic_helper_commit_planes function call.
atomic_commit_tail callback implements this call ordering.
- allow plane commit only in case that CRTC device is enabled.
. for this, it calls atomic_helper_commit_planes function
with DRM_PLANE_COMMIT_ACTIVE_ONLY flag in atomic_commit_tail callback.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Inki Dae [Tue, 17 Jan 2017 10:47:26 +0000 (19:47 +0900)]
drm/exynos: remove unnecessary codes
This patch removes exynos_drm_crtc_cancel_page_flip call
when drm is closed because at that time, events will be released
by drm_events_release function.
Changelog v1:
- remove exynos_drm_crtc_cancel_page_flip function also because
this funtion isn't used anymore.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Marek Szyprowski [Fri, 13 Jan 2017 08:30:00 +0000 (09:30 +0100)]
drm/exynos: mic: Add runtime PM support
This patch adds runtime support calls to notify device core when MIC
device is really in use. Runtime PM is implemented by enabling and
disabling clocks like in other Exynos DRM subdrivers. Adding runtime
PM support is needed to let power domain with this device to be turned
off when display is not used.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Daniel Vetter [Tue, 27 Dec 2016 10:49:23 +0000 (11:49 +0100)]
drm/exynos: Stop using drm_framebuffer_unregister_private
This is the deprecated function for when you embedded the framebuffer
somewhere else (which breaks refcounting). But exynos is using
drm_framebuffer_remove and a free-standing fb, so this is rendundant.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Hoegeun Kwon [Thu, 5 Jan 2017 10:20:07 +0000 (19:20 +0900)]
drm/exynos: mic: Fix parse_dt function
The OF graph is not necessary because the panel is a child of
dsi. therefore, the parse_dt function of dsi does not need to
check the remote_node connected to the panel. and the whole
parse_dt function should be refactored later.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Hoegeun Kwon [Thu, 5 Jan 2017 10:20:06 +0000 (19:20 +0900)]
drm/exynos: mic: Add mode_set callback function
Before applying the patch, used the of_get_videomode function to
parse the display-timings in the panel which is the child driver
of dsi in the devicetree. this is wrong. So removed the
of_get_videomode and fixed to get videomode struct through
mode_set callback function.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Gustavo Padovan [Fri, 27 Jan 2017 17:54:44 +0000 (15:54 -0200)]
MAINTAINERS: add dma-fence* files to Sync File maintainership
As Sync File is highly dependent on dma-fence* tracks it
under SYNC FILE_FRAMEWORK as well.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170127175444.7995-1-gustavo@padovan.org
Boris Brezillon [Mon, 28 Nov 2016 14:56:53 +0000 (15:56 +0100)]
drm/atmel-hlcdc: Rework the fbdev creation logic
Now that we wait for DRM panels to be available before registering the
DRM device (returning -EPROBE_DEFER if the panel has not been probed
yet), we no longer need to put the fbdev creation code in
->output_poll_changed().
This removes the 10 secs delay between DRM dev registration and fbdev
creation (polling period = 10 seconds).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Alex Vazquez <avazquez.dev@gmail.com>
Noralf Trønnes [Thu, 26 Jan 2017 22:56:18 +0000 (23:56 +0100)]
drm/vc4: Remove vc4_debugfs_cleanup()
drm_debugfs_cleanup() now removes all minor->debugfs_list entries
automatically, so the drm_driver.debugfs_cleanup callback is not
needed.
Cc: eric@anholt.net
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170126225621.12314-17-noralf@tronnes.org
Shawn Guo [Thu, 19 Jan 2017 14:28:38 +0000 (22:28 +0800)]
drm: zte: add tvenc driver support
It adds the TV Encoder driver to support video output in PAL and NTSC
format. The driver uses syscon/regmap interface to configure register
bit sitting in SYSCTRL module for DAC power control.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Shawn Guo [Thu, 19 Jan 2017 15:34:25 +0000 (23:34 +0800)]
dt: add bindings for ZTE tvenc device
It adds bindings doc for ZTE VOU TV Encoder device.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Shawn Guo [Thu, 12 Jan 2017 14:20:31 +0000 (22:20 +0800)]
drm: zte: add function to configure vou_ctrl dividers
The clock control module (CRM) cannot always provide desired frequency
for all VOU output devices. That's why VOU integrates a few dividers
to further divide the clocks from CRM. Let's add an interface for
configuring these dividers.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Shawn Guo [Thu, 12 Jan 2017 08:27:35 +0000 (16:27 +0800)]
drm: zte: move struct vou_inf into zx_vou driver
Although data in struct vou_inf is defined per output device, it doesn't
belong to the device itself but VOU control module. All these data can
just be defined in VOU driver, and output device driver only needs to
invoke VOU driver function with device ID to enable/disable specific
output device.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Shawn Guo [Thu, 12 Jan 2017 06:44:40 +0000 (14:44 +0800)]
drm: zte: add interlace mode support
It adds interlace mode support in VOU TIMING_CTRL and channel control
block, so that VOU driver gets ready to support output device in
interlace mode like TV Encoder.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Shawn Guo [Wed, 16 Nov 2016 06:43:59 +0000 (14:43 +0800)]
drm: zte: add overlay plane support
It enables VOU VL (Video Layer) to support overlay plane with scaling
function. VL0 has some quirks on scaling support. We choose to skip it
and only adds VL1 and VL2 into DRM core for now.
Function zx_plane_atomic_disable() gets moved around with no changes to
save a forward declaration.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Shawn Guo [Thu, 29 Dec 2016 00:03:03 +0000 (08:03 +0800)]
drm: zte: add .atomic_disable hook to disable graphic layer
There are a few hardware bits for each graphic layer to control main/aux
channel and clock selection, as well as the layer enabling. These bits
sit outside the layer block itself, but in VOU control glue block. We
currently set these bits up at CRTC initialization for once, and do not
support disabling the layer.
This patch creates a pair of functions zx_vou_layer_enable[disable] to
be invoked from plane hooks .atomic_update and .atomic_disable to set up
and tear down the layer. This is generic for both graphic and video
layers, so it will make the overlay plane support to be added later much
easier.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Shawn Guo [Wed, 28 Dec 2016 06:41:37 +0000 (14:41 +0800)]
drm: zte: make zx_plane accessible from zx_vou driver
Move struct zx_plane from zx_plane.c to zx_plane.h, so that it can be
accessed from zx_vou driver, and we can save the use of struct
zx_layer_data completely. More importantly, those additional data used
by VOU controller to enable/disable graphic and video layers can later
be added and accessed much more easily from zx_vou driver.
While at it, we make two changes to zx_plane_init() interface:
- Encode struct device pointer in zx_plane, so that we do not need to
pass it as a parameter.
- Change return of zx_plane_init() from struct drm_plane pointer to
error code, since we can get the pointer from zx_plane in zx_vou
driver now.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Shawn Guo [Thu, 1 Dec 2016 09:20:31 +0000 (17:20 +0800)]
drm: zte: support hdmi audio through spdif
It enables HDMI audio support through SPDIF interface based on generic
hdmi-audio-codec driver. The HDMI hardware supports more audio
interfaces than SPDIF, like I2S, which may be added later.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Shawn Guo [Mon, 9 Jan 2017 07:19:19 +0000 (15:19 +0800)]
drm: zte: select VIDEOMODE_HELPERS in Kconfig
ZTE DRM driver uses drm_display_mode_to_videomode() in function
zx_crtc_enable(). Select VIDEOMODE_HELPERS in Kconfig to fix the
following link error.
LD vmlinux.o
MODPOST vmlinux.o
drivers/built-in.o: In function `zx_crtc_enable':
:(.text+0xbdeb8): undefined reference to `drm_display_mode_to_videomode'
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Chris Wilson [Tue, 24 Jan 2017 11:57:58 +0000 (11:57 +0000)]
dma/fence: Export enable-signaling tracepoint for emission by drivers
Currently this tracepoint is solely used by dma_fence_enable_sw_signaling,
however I have a need to manually perform the hw enabling of the
signaling and would like to emit this tracepoint for completeness.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170124115758.31353-1-chris@chris-wilson.co.uk
Christian König [Wed, 18 Jan 2017 13:49:43 +0000 (14:49 +0100)]
drm/amdgpu: fix amdgpu_bo_va_mapping flags
They are 64bit not 32 for a while now.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Mon, 7 Nov 2016 09:19:40 +0000 (10:19 +0100)]
drm/amdgpu: access stolen VRAM directly on CZ (v2)
We don't need to use the PCI BAR on APUs. This allows us to access
the full VRAM directly without being limited by the BAR size.
v2: squash in 64bit shift fix
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Fri, 4 Nov 2016 12:23:41 +0000 (13:23 +0100)]
drm/amdgpu: access stolen VRAM directly on KV/KB (v2)
We don't need to use the PCI BAR on APUs. This allows us to access
the full VRAM directly without being limited by the BAR size.
v2: squash in 64bit shift fix
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rex Zhu [Fri, 20 Jan 2017 06:30:51 +0000 (14:30 +0800)]
drm/amdgpu: fix kernel panic when dpm disabled on Kv.
Return early if it's disabled.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rex Zhu [Fri, 20 Jan 2017 06:27:22 +0000 (14:27 +0800)]
drm/amdgpu: fix dpm bug on Kv.
1. current_ps/request_ps not update.
2. compare crrent_ps and request_ps, if same,
don't re-set power state.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rex Zhu [Tue, 24 Jan 2017 09:47:36 +0000 (17:47 +0800)]
drm/amd/powerplay: fix regresstion issue can't set manual dpm mode.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Wed, 25 Jan 2017 20:35:38 +0000 (15:35 -0500)]
drm/amdgpu: handle vfct with multiple vbios images
The vfct table can contain multiple vbios images if the
platform contains multiple GPUs. Noticed by netkas on
phoronix forums. This patch fixes those platforms.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Alex Deucher [Wed, 25 Jan 2017 20:33:44 +0000 (15:33 -0500)]
drm/radeon: handle vfct with multiple vbios images
The vfct table can contain multiple vbios images if the
platform contains multiple GPUs. Noticed by netkas on
phoronix forums. This patch fixes those platforms.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Alex Deucher [Tue, 24 Jan 2017 23:00:57 +0000 (18:00 -0500)]
drm/amdgpu: move misc si headers into amdgpu
Move these to the amdgpu directory to match what we
do for other asics.
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Tue, 24 Jan 2017 22:54:37 +0000 (17:54 -0500)]
drm/amdgpu: remove unused header si_reg.h
All of these are available elsewhere.
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Tue, 24 Jan 2017 22:01:11 +0000 (17:01 -0500)]
drm/radeon: drop pitcairn dpm quirks
No longer necessary with the new 58 mc ucode.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=76490
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Tue, 24 Jan 2017 21:59:35 +0000 (16:59 -0500)]
drm/amdgpu: drop pitcairn dpm quirks
No longer necessary with the new 58 mc ucode.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Arvind Yadav [Tue, 24 Jan 2017 09:16:16 +0000 (14:46 +0530)]
drm: radeon: radeon_ttm: Handle return NULL error from ioremap_nocache
Here, If ioremap_nocache will fail. It will return NULL.
Kernel can run into a NULL-pointer dereference.
This error check will avoid NULL pointer dereference.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Arvind Yadav [Tue, 24 Jan 2017 09:25:33 +0000 (14:55 +0530)]
drm/amd/amdgpu/amdgpu_ttm: Handle return NULL error from ioremap_nocache
Here, If ioremap_nocache will fail. It will return NULL.
Kernel can run into a NULL-pointer dereference.
This error check will avoid NULL pointer dereference.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Yintian Tao [Sun, 22 Jan 2017 07:16:51 +0000 (15:16 +0800)]
drm/amdgpu: add new virtual display ID
In the case of pass-through, amdgpu.ko may be included into a image
with the hard code ID therefore loading driver with specified virtual
display ID will lose efficacy when the BDF of GPU modifies.So add the
new ID string "all" for it as same as vf case what does.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Yintian Tao <yttao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Junwei Zhang [Mon, 23 Jan 2017 08:30:38 +0000 (16:30 +0800)]
drm/amd/amdgpu: remove the uncessary parameter for ib scheduler
Signed-off-by: Junwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Nils Holland [Sun, 22 Jan 2017 19:15:27 +0000 (20:15 +0100)]
drm/amdgpu: Bring bo creation in line with radeon driver (v2)
Add the bo creation changes that have been done to the radeon driver in
recent times, e.g. disable GTT WC on 32 bit because it is broken there,
and also disable it generally (and print a warning message) when
CONFIG_X86_PAT is not set.
v2: agd: fix warning in defined(CONFIG_X86) && !defined(CONFIG_X86_PAT)
case
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Nils Holland <nholland@tisys.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Nicolas Iooss [Sun, 22 Jan 2017 13:47:39 +0000 (14:47 +0100)]
drm/amd/powerplay: fix misspelling in header guard
In smu7_clockpowergating.h, the #ifndef statement which prevents
multiple inclusions of the header file uses _SMU7_CLOCK_POWER_GATING_H_
but the following #define statement uses _SMU7_CLOCK__POWER_GATING_H_.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Thu, 12 Jan 2017 10:54:11 +0000 (11:54 +0100)]
drm/ttm: revert "add optional LRU removal callback v2"
Without the custom LRU management the callback is not used any more.
agd: fix trivial warning
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-and-Tested-by: Roger.He <Hongbo.He@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Thu, 12 Jan 2017 10:50:13 +0000 (11:50 +0100)]
drm/ttm: revert "implement LRU add callbacks v2"
The additional housekeeping had too much CPU overhead,
let's use the BO priorities instead.
agd: also revert hibmc changes
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-and-Tested-by: Roger.He <Hongbo.He@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Mon, 23 Jan 2017 21:28:06 +0000 (16:28 -0500)]
drm/amdgpu: double the priority of kernel allocations
Give kernel allocations a higher priority cause it is often
more work to swap them back in.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Roger.He <Hongbo.He@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Tue, 10 Jan 2017 16:27:49 +0000 (17:27 +0100)]
drm/amdgpu: user BO priority instead of self coding it (v2)
Keeping groups of BOs on the LRU is to time consuming on command submission.
Instead use the newly added BO priority to give a certain eviction order.
v2: agd: trivial warning fix
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Roger.He <Hongbo.He@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Tue, 10 Jan 2017 13:08:28 +0000 (14:08 +0100)]
drm/ttm: add BO priorities for the LRUs
This way the driver can specify a priority for a BO which has the effect that
a BO is only evicted when all other BOs with a lower priority are evicted
first.
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Roger.He <Hongbo.He@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Fri, 6 Jan 2017 18:16:07 +0000 (19:16 +0100)]
drm/ttm: remove allow_errors parameter from ttm_bo_force_list_clean
Not allowing errors here is completely pointless and actually dangerous
cause trying to continue on an error can cause an endless loop.
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Roger.He <Hongbo.He@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Xiangliang Yu [Wed, 18 Jan 2017 04:50:14 +0000 (12:50 +0800)]
drm/amdgpu/vi: fix mailbox irq mistake
For virt, freed mailbox irq should be handled in hw fini, not hw
init. Correct it.
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Reviewed-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Xiangliang Yu [Wed, 18 Jan 2017 04:47:55 +0000 (12:47 +0800)]
drm/amdgpu: fix reboot failure issue for virtualization
Reboot process will call HW fini functions of IP blocks. For virt,
need to send event three before hw fini and send event four after
hw fini.
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Reviewed-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Tom St Denis [Wed, 18 Jan 2017 18:01:25 +0000 (13:01 -0500)]
drm/amd/amdgpu: Add PCI info to gca_config debugfs
So we can determine which device the entry is before connecting
a display.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Monk Liu [Wed, 18 Jan 2017 02:38:06 +0000 (10:38 +0800)]
drm/amdgpu:insert switch buffer only for VM submit
for non-VM submit which is from kernel side, no need
to switch buffer at all.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Monk Liu [Wed, 18 Jan 2017 02:37:34 +0000 (10:37 +0800)]
drm/amdgpu:Preamble is forbid to be ignored in SRIOV
SR-IOV requires the preamble.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Monk Liu [Wed, 18 Jan 2017 02:31:18 +0000 (10:31 +0800)]
drm/amdgpu:set cond_exec polling value to 1 in ring_init
no need to set it per ib_schedule(), hw won't override
this polling address.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Monk Liu [Tue, 17 Jan 2017 02:56:16 +0000 (10:56 +0800)]
drm/amdgpu:in cntx_ctrl we need insert meta-init for CE/DE(V2)
to support SRIOV preemption.
v2:
fix emit_frame_size
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Monk Liu [Tue, 17 Jan 2017 02:55:42 +0000 (10:55 +0800)]
drm/amdgpu:introduce new flag to identify VM domain for cntx_ctrl
To determine whether the context uses GPUVM or not.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Monk Liu [Tue, 17 Jan 2017 02:52:58 +0000 (10:52 +0800)]
drm/amdgpu:implement CE/DE meta-init routines
those package need to insert into ring buffer for
SRIOV case. they are used to let CP do preemption.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Monk Liu [Tue, 17 Jan 2017 02:52:33 +0000 (10:52 +0800)]
drm/amdgpu:implement ring_write_multiple
Write multiple dwords to the ring.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Monk Liu [Thu, 12 Jan 2017 07:32:44 +0000 (15:32 +0800)]
drm/amdgpu:add META_DATA struct for CSA/SRIOV v2
META-DATA is used in GFX cmd submit, we have two
format suit for META-DATA-init, one is legacy and another
is for chained-ib preempt, which is used in vulkan
UMD.
v2: drop use CP version number to judge if chain-ib
supports or not, we wait for it mature
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rex Zhu [Thu, 12 Jan 2017 13:50:18 +0000 (21:50 +0800)]
drm/amdgpu: refine ci uvd dpm code.
Fix up the powergating logic.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Ack-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Nils Wallménius [Mon, 16 Jan 2017 20:56:48 +0000 (21:56 +0100)]
drm/amdgpu: simplify allocation of scratch regs
The scratch regs are sequential so there's no need to keep
them in an array, we can just return the index of the first
free register + the base register. Also change the array
of bools for keeping track of the free regs to a bitfield.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Nils Wallménius <nils.wallmenius@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
projects / openwrt / staging / blogic.git / log