[media] dib0700: Return -EINTR and unlock mutex if locking attempts fails

In 'dib0700_i2c_xfer_new()' and 'dib0700_i2c_xfer_legacy()'
we are taking two locks:
                1. i2c_mutex
                2. usb_mutex
If attempt to take 'usb_mutex' lock fails then the previously taken
lock 'i2c_mutex' should be unlocked and -EINTR should be returned so
that caller can take appropriate action.

If locking attempt was interrupted by a signal then
we should return -EINTR. At present we are returning '0' for
such scenarios  which is wrong.

Replace -EAGAIN by -EINTR as a return type for the the scenario
where locking attempt was interrupted by signal.

Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] cxd2820r: tweak search algorithm behavior

MPIS based STBs running 3.x kernels and the Enigma2 OS are not able to tune
DVB-T channels with the PCTV 290e using the current cxd2820r driver.
DVB-T2 channels instead work properly.

This patch fixes the problem by changing the condition to break out from the
wait lock loop in the "search" function of the cxd2820r demodulator from
FE_HAS_SIGNAL to FE_HAS_LOCK.

As a consequence, the "search" function of the demodulator driver now returns
DVBFE_ALGO_SEARCH_SUCCESS only if the frequency lock is successfully acquired.

This behavior seems consistent with other demodulator drivers (e.g. stv090x,
hd29l2, stv0900, stb0899, mb86a16).

This patch has been successfully tested with DVB-T and DVB-T2 signals,
on both PC and the mipsel STB running Enigma2.
No apparent side effect has been observed on PC applications like Kaffeine.
DVB-C is not available in my country so it's not tested.

Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] em28xx-dvb: enable LNA for cxd2820r in DVB-T mode

Enable the LNA amplifier also for DVB-T (like for DVB-T2 and DVB-C);
this greatly improves reception of weak signals without affecting the reception
of the strong ones.

Experimental data (collected with the mipsel STB) on the weakest frequencies
available in my area:

LNA OFF:

MUX          level   BER     picture

RAI mux 4    72%     32000   corrupted
TIMB 2       75%     14      OK
TVA Vicenza  68%     32000   corrupted
RAI mux 2    78%     14      OK

LNA ON:

MUX          level   BER     picture

RAI mux 4    73%     1500    OK
TIMB 2       76%     0       OK
TVA Vicenza  69%     0       OK
RAI mux 2    79%     0       OK

Moreover, with LNA enabled, the PCTV 290e was able to pick up 2 new frequencies
matching the integrated tuner of my Panasonic G20 TV, which is really good.

Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] saa7134: remove unused  log_err() macro

As reported by Masanari, this macro is using "KERN_ERR"
instead of "KERN_ERROR". That would lead into a compilation
breakage, if this macro were used somewhere inside the driver.

Instead of fixing the macro, as originally proposed, let's just
remove the dead code.

Reported-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] staging: easycap: Split easycap_delete() into several pieces

The patch splits easycap_delete(), which is in charge of
buffer deallocation, into smaller functions each
deallocating a specific kind of buffer.

Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] staging: easycap: Clean comment style in easycap_delete()

Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] staging: easycap: Clean comment style in easycap_usb_disconnect()

Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] staging: easycap: Split audio buffer and urb allocation

When the device is probed, this driver allocates
audio buffers, and audio urbs.
This patch just split this into separate functions,
which helps clearing the currently gigantic probe function.

Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] staging: easycap: Push video registration to easycap_register_video()

Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] staging: easycap: Initialize 'ntsc' parameter before usage

This parameter is now initialized at init_easycap(),
this way we assure it won't be used uninitialized.

Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] staging: easycap: Push bInterfaceNumber saving to config_easycap()

Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] staging: easycap: Split buffer and video urb allocation

When the device is probed, this driver allocates
frame buffers, field buffers, isoc buffers and urbs.
This patch just split this into separate functions,
which helps clearing the currently gigantic probe function.

Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] staging: easycap: Split device struct alloc and retrieval code

When the device is probed a driver struct is either
allocated or retrieved.
This operation is logically splitted in several functions.

Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: soc-camera: (cosmetic) use a more explicit name for a host handler

Use "enum_framesizes" instead of "enum_fsizes" to more precisely follow
the name of the respective ioctl().

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Sergio Aguirre <sergio.a.aguirre@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: marvell-ccic: (cosmetic) remove redundant variable assignment

The "ret = 0" assignment in mcam_vidioc_s_fmt_vid_cap() is redundant,
because at that location "ret" is anyway guaranteed to be == 0.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l2-event: fix regression with initial event handling

If the V4L2_EVENT_SUB_FL_SEND_INITIAL was set, then the application expects
to receive an initial event of the initial value of the control.

However, commit c53c2549333b340e2662dc64ec81323476b69a97 that added the new
v4l2_subscribed_event_ops introduced a regression: while the code still queued
that initial event the __v4l2_event_queue_fh() function was modified to ignore
such requests if sev->elems was 0 (meaning that the event subscription wasn't
finished yet).

And sev->elems was only set to a non-zero value after the add operation
returned.

This patch fixes this by passing the elems value to the add function. Then the
add function can set it before queuing the initial event.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Merge remote-tracking branch 'linus/master' into staging/for_v3.5

* linus/master: (805 commits)
  tty: Fix LED error return
  openvswitch: checking wrong variable in queue_userspace_packet()
  bonding: Fix LACPDU rx_dropped commit.
  Linux 3.4-rc7
  ARM: EXYNOS: fix ctrlbit for exynos5_clk_pdma1
  ARM: EXYNOS: use s5p-timer for UniversalC210 board
  ARM / mach-shmobile: Invalidate caches when booting secondary cores
  ARM / mach-shmobile: sh73a0 SMP TWD boot regression fix
  ARM / mach-shmobile: r8a7779 SMP TWD boot regression fix
  ARM: mach-shmobile: convert ag5evm to use the generic MMC GPIO hotplug helper
  ARM: mach-shmobile: convert mackerel to use the generic MMC GPIO hotplug helper
  MAINTAINERS: Add myself as the cpufreq maintainer
  dm mpath: check if scsi_dh module already loaded before trying to load
  dm thin: correct module description
  dm thin: fix unprotected use of prepared_discards list
  dm thin: reinstate missing mempool_free in cell_release_singleton
  gpio/exynos: Fix compiler warnings when non-exynos machines are selected
  gpio: pch9: Use proper flow type handlers
  powerpc/irq: Fix another case of lazy IRQ state getting out of sync
  ks8851: Update link status during link change interrupt
  ...

Conflicts:
drivers/media/common/tuners/xc5000.c
drivers/media/common/tuners/xc5000.h
drivers/usb/gadget/uvc_queue.c

[media] lmedm04: Initialize a variable before its usage

The variable ret is used uninitialized.
It should be initialized before used.
Initialize it.

Signed-off-by: Il Han <corone.il.han@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] it913x.: Fix a misuse of ||

On Mon, 2012-05-07 at 07:45 -0300, Mauro Carvalho Chehab wrote:
> Malcolm,
>
> Em 04-04-2012 20:00, Joe Perches escreveu:
> > Likely these should be && not ||
> >
> > drivers/scsi/FlashPoint.c: if(bit_cnt != 0 || bit_cnt != 8)
>
> > drivers/media/dvb/dvb-usb/it913x.c: if (ret == 0 || ret != -EBUSY || ret != -ETIMEDOUT)
> > drivers/media/dvb/dvb-usb/it913x.c: if (ret == 0 || ret != -EBUSY || ret != -ETIMEDOUT)
>
> Could you please take a look on the above?

Hmm... yes, thanks, also a bug.

Just check for -EBUSY && -ETIMEDOUT

Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] staging/media/as102: removed else statements

The else statement is actually not required, as we can assign AS10X_CMD_ERROR
to the error variable directly.

Signed-off-by: joseph daniel <josephdanielwalter@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] em28xx: Remove unused wait_queue's

Nobody ever waits on any of these wait_queue's,
so this patch removes them completely.
Tested by compilation only.

Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] drivers/media: add missing __devexit_p() annotations

Drivers that refer to a __devexit function in an operations
structure need to annotate that pointer with __devexit_p so
replace it with a NULL pointer when the section gets discarded.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media/video: add I2C dependencies

Davinci VIDEO_VPFE_CAPTURE depends on I2C, so reflect that
in Kconfig to avoid build failures in random configurations.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media/rc: IR_SONY_DECODER depends on BITREVERSE

The IR sony decoder is making use of 'bitrev8' that,
in turn, requires BITREVERSE.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb/drxd: stub out drxd_attach when not built

This avoids getting
drivers/media/video/em28xx/em28xx-dvb.c:721: \
                       undefined reference to `drxd_attach'

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] video/omap24xxcam: use __iomem annotations

MMIO registers are __iomem tokens in virtual address space,
not integers.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] Convert I2C drivers to dev_pm_ops

The legacy I2C PM functions have been deprecated and warning on boot
for over a year, convert the drivers still using them to dev_pm_ops.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca: passing wrong length parameter to reg_w()

This looks like a cut an paste error.  This is a two byte array but we
use 8 as a length parameter.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] via-camera: specify XO-1.5 camera clock speed

For the ov7670 camera to return images at the requested frame rate,
it needs to make calculations based on the clock speed, which is
a completely external factor (depends on the wiring of the system).

On the XO-1.5, which is the only known via-camera user, the camera
is clocked at 90MHz.

Pass this information to the ov7670 driver, to fix an issue where
a framerate of 3x the requested amount was being provided.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] em28xx: Remove unused enum em28xx_io_method

Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] em28xx: Remove unused field from em28xx_buffer struct

Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] em28xx: Remove unused list_head struct for queued buffers

The list_head struct usage was fully removed by commit
d7aa80207babe694b316a48200b096cf0336ecb3.

Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] em28xx: Make card_setup() and pre_card_setup() static

This cleans namespace a bit by making em28xx_card_setup()
em28xx_pre_card_setup() static functions.

Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Merge branch 'v4l_for_linus' of git://git./linux/kernel/git/mchehab/linux-media

Pull media fixes from Mauro Carvalho Chehab:
 "For a some fix patches for v3.4, including a regression fix at DVB core"

Fix up trivial conflicts in Documentation/feature-removal-schedule.txt

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] gspca - sonixj: Fix a zero divide in isoc interrupt
  [media] media: videobuf2-dma-contig: include header for exported symbols
  [media] media: videobuf2-dma-contig: quiet sparse noise about plain integer as NULL pointer
  [media] media: vb2-memops: Export vb2_get_vma symbol
  [media] s5p-fimc: Correct memory allocation for VIDIOC_CREATE_BUFS
  [media] s5p-fimc: Fix locking in subdev set_crop op
  [media] dvb_frontend: fix a regression with DVB-S zig-zag
  [media] fintek-cir: change || to &&
  [media] V4L: Schedule V4L2_CID_HCENTER, V4L2_CID_VCENTER controls for removal
  [media] rc: Postpone ISR registration
  [media] marvell-cam: fix an ARM build error
  [media] V4L: soc-camera: protect hosts during probing from overzealous user-space

Merge git://git./linux/kernel/git/davem/net

Pull networking fixes from David Miller:
 "The main purpose of this pull request is to fix up the erroneous
  bonding patch I applied last round.  I meant to apply v4 of the patch
  from Jiri but I applied v3 by accident.  Mea culpa.

  Also, eagle eyed Dan Carpenter noticed that openvswitch has one of
  those "X = alloc(); if (!Y)" mistakes, test the proper pointer
  instead."

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  openvswitch: checking wrong variable in queue_userspace_packet()
  bonding: Fix LACPDU rx_dropped commit.

[media] v4l2-dev: rename two functions

Rename the function v4l2_dont_use_lock to v4l2_disable_ioctl_locking,
and rename v4l2_dont_use_cmd to v4l2_disable_ioctl.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l2-dev.h: add comment not to use V4L2_FL_LOCK_ALL_FOPS in new drivers

This flag is for legacy drivers only and will go away in the future.

A note regarding commit 5126f2590bee412e3053de851cb07f531e4be36a
(v4l2-dev: add flag to have the core lock all file operations):

That commit message suggests that by not taking the core lock for fops
other than unlocked_ioctl all problems relating to AB-BA locking and
mm->mmap_sem are solved. This is not the case.

More work needs to be done by moving the core lock further down into
video_ioctl2. It should only be taken after the copy_from/to_user calls
are done.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l2-framework.txt: update the core lock documentation

Thanks to Laurent Pinchart for pointing out that this information was missing.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] av7110: fix v4l2_compliance test issues

Besides the usual inconsistencies in input enumeration there was also a
kernel crash if you tried to poll on a vbi node. The checks for sliced
vbi output vs vbi capture were not complete enough.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] vivi: add the alpha component control

Useful to set the alpha component for the pixel formats with an alpha channel.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] vivi: add more pixelformats

This is very useful for testing whether userspace can handle the various formats
correctly.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] hexium-orion: fix incorrect input table

Fix the standard and audioset values.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] hexium-gemini: remove B&W control, fix input table

The B&W control never worked, and you get the same effect by setting saturation to the
lowest value. So it has been removed. Also fixed some incorrect entries in the input
table. This driver now passes v4l2-compliance.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] fixes and add querystd support to mxb

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] saa7146: fix querycap, vbi/video separation and g/s_register

The querycap ioctl returned an incorrect version number and incorrect
capabilities (mixing up vbi and video caps).

The reason for that was that video nodes could do vbi activities: that
should be separated between the vbi and video nodes.

There were also a few minor problems with dbg_g/s_register that have
been resolved. The mxb/saa7146 driver now passes the v4l2_compliance tests.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] saa7146: support control events and priority handling

Use v4l2_fh which gives you control events and priority handling for free.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] saa7146: rename vbi/video_q to vbi/video_dmaq

There was also a vbi_q and video_q in saa7146_fh, so that was confusing.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] saa7146: remove the unneeded type field from saa7146_fh

This information can also be retrieved from struct video_device.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] saa7146: move vbi fields from saa7146_fh to saa7146_vv

This fields are global and don't belong in a fh struct.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] saa7146: move video_fmt from saa7146_fh to saa7146_vv

This is a global structure and does not belong to saa7146_fh.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] saa7146: move overlay information from saa7146_fh into saa7146_vv

This is global information, not per-filehandle information.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mxb: fix audio and standard handling

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] tda9840: fix setting of the audio mode

You have to first detect the current rxsubchans (mono, stereo or bilingual),
and depending on that you can set the audio mode. It does not automatically
switch when the audio channels change.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mxb: simplify a line that was too long

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mxb: fix audio handling

Instead of using custom ioctls use the VIDIOC_ENUM/G/S/_AUDIO ioctls.
Also send the same audio to both CDROM-out and line-out.

This is what you would expect and anyway, the CDROM-out connector is unlikely
to be used these days as it is obsolete.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mxb: fix initial audio + ntsc/secam support

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mxb/saa7146: first round of cleanups

Convert to the control framework, fix the easy v4l2-compliance failures.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l/dvb: fix compiler warnings

media_build/v4l/drxk_hard.c: In function 'DownloadMicrocode':
media_build/v4l/drxk_hard.c:1388:6: warning: variable 'BlockCRC' set but not used [-Wunused-but-set-variable]
media_build/v4l/drxk_hard.c:1384:6: warning: variable 'Drain' set but not used [-Wunused-but-set-variable]
media_build/v4l/drxk_hard.c:1383:6: warning: variable 'Flags' set but not used [-Wunused-but-set-variable]
media_build/v4l/lmedm04.c: In function 'lme2510_probe':
media_build/v4l/lmedm04.c:1208:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/hopper_cards.c: In function 'hopper_irq_handler':
media_build/v4l/hopper_cards.c:68:26: warning: variable 'lstat' set but not used [-Wunused-but-set-variable]
media_build/v4l/mantis_cards.c: In function 'mantis_irq_handler':
media_build/v4l/mantis_cards.c:76:26: warning: variable 'lstat' set but not used [-Wunused-but-set-variable]
media_build/v4l/mantis_dma.c: In function 'mantis_dma_stop':
media_build/v4l/mantis_dma.c:202:16: warning: variable 'mask' set but not used [-Wunused-but-set-variable]
media_build/v4l/mantis_dma.c:202:6: warning: variable 'stat' set but not used [-Wunused-but-set-variable]
media_build/v4l/mantis_evm.c: In function 'mantis_hifevm_work':
media_build/v4l/mantis_evm.c:44:17: warning: variable 'gpif_mask' set but not used [-Wunused-but-set-variable]
media_build/v4l/stb0899_drv.c: In function 'stb0899_init_calc':
media_build/v4l/stb0899_drv.c:640:5: warning: variable 'agc1cn' set but not used [-Wunused-but-set-variable]
media_build/v4l/stb0899_drv.c: In function 'stb0899_diseqc_init':
media_build/v4l/stb0899_drv.c:830:13: warning: variable 'f22_rx' set but not used [-Wunused-but-set-variable]
media_build/v4l/stb0899_drv.c:826:31: warning: variable 'tx_data' set but not used [-Wunused-but-set-variable]
media_build/v4l/stv0900_sw.c: In function 'stv0900_track_optimization':
media_build/v4l/stv0900_sw.c:838:26: warning: variable 'rolloff' set but not used [-Wunused-but-set-variable]
media_build/v4l/ir-sanyo-decoder.c: In function 'ir_sanyo_decode':
media_build/v4l/ir-sanyo-decoder.c:59:14: warning: variable 'not_address' set but not used [-Wunused-but-set-variable]
media_build/v4l/mceusb.c: In function 'mceusb_dev_printdata':
media_build/v4l/mceusb.c:523:46: warning: variable 'data5' set but not used [-Wunused-but-set-variable]

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l/dvb: fix compiler warnings

media_build/v4l/stb6100.c: In function 'stb6100_read_reg':
media_build/v4l/stb6100.c:161:6: warning: variable 'rc' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx24110.c: In function 'cx24110_read_ucblocks':
media_build/v4l/cx24110.c:515:6: warning: variable 'lastbyer' set but not used [-Wunused-but-set-variable]
media_build/v4l/dib9000.c: In function 'dib9000_mbx_process':
media_build/v4l/dib9000.c:711:6: warning: variable 'tmp' set but not used [-Wunused-but-set-variable]
media_build/v4l/zl10353.c: In function 'zl10353_init':
media_build/v4l/zl10353.c:562:6: warning: variable 'rc' set but not used [-Wunused-but-set-variable]
media_build/v4l/stv0297.c: In function 'stv0297_set_frontend':
media_build/v4l/stv0297.c:417:16: warning: variable 'starttime' set but not used [-Wunused-but-set-variable]
media_build/v4l/lgs8gxx.c: In function 'lgs8gxx_set_mode_manual':
media_build/v4l/lgs8gxx.c:265:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/af9013.c: In function 'af9013_statistics_work':
media_build/v4l/af9013.c:517:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/stv090x.c: In function 'stv090x_optimize_track':
media_build/v4l/stv090x.c:2845:23: warning: variable 'rolloff' set but not used [-Wunused-but-set-variable]
media_build/v4l/stv090x.c: In function 'stv090x_algo':
media_build/v4l/stv090x.c:3177:28: warning: variable 'no_signal' set but not used [-Wunused-but-set-variable]
media_build/v4l/it913x-fe.c: In function 'it913x_fe_read_ber':
media_build/v4l/it913x-fe.c:636:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/it913x-fe.c: In function 'it913x_fe_get_frontend':
media_build/v4l/it913x-fe.c:661:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/it913x-fe.c: In function 'it913x_fe_set_frontend':
media_build/v4l/it913x-fe.c:694:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/m88rs2000.c: In function 'm88rs2000_set_fec':
media_build/v4l/m88rs2000.c:657:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/dst_ca.c: In function 'ca_send_message':
media_build/v4l/dst_ca.c:480:15: warning: variable 'ca_message_header_len' set but not used [-Wunused-but-set-variable]
media_build/v4l/smssdio.c: In function 'smssdio_interrupt':
media_build/v4l/smssdio.c:117:11: warning: variable 'isr' set but not used [-Wunused-but-set-variable]

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l: fix compiler warnings

media_build/v4l/adv7343.c: In function 'adv7343_setstd':
media_build/v4l/adv7343.c:133:6: warning: variable 'output_idx' set but not used [-Wunused-but-set-variable]
media_build/v4l/tvp5150.c: In function 'tvp5150_mbus_fmt':
media_build/v4l/tvp5150.c:833:14: warning: variable 'std' set but not used [-Wunused-but-set-variable]
media_build/v4l/tvp7002.c: In function 'tvp7002_query_dv_preset':
media_build/v4l/tvp7002.c:673:18: warning: variable 'device' set but not used [-Wunused-but-set-variable]
media_build/v4l/c-qcam.c: In function 'qc_capture':
media_build/v4l/c-qcam.c:381:33: warning: variable 'bitsperxfer' set but not used [-Wunused-but-set-variable]
media_build/v4l/pms.c: In function 'pms_s_std':
media_build/v4l/pms.c:738:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/pms.c: In function 'init_mediavision':
media_build/v4l/pms.c:959:6: warning: variable 'id' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-alsa.c: In function 'cx25821_irq':
media_build/v4l/cx25821-alsa.c:294:6: warning: variable 'audint_count' set but not used [-Wunused-but-set-variable]
media_build/v4l/zr364xx.c: In function 'zr364xx_fillbuff':
media_build/v4l/zr364xx.c:510:25: warning: variable 'frm' set but not used [-Wunused-but-set-variable]
media_build/v4l/s2255drv.c: In function 's2255_fillbuff':
media_build/v4l/s2255drv.c:637:23: warning: variable 'frm' set but not used [-Wunused-but-set-variable]
media_build/v4l/s2255drv.c: In function 'vidioc_s_fmt_vid_cap':
media_build/v4l/s2255drv.c:990:6: warning: variable 'norm' set but not used [-Wunused-but-set-variable]
media_build/v4l/tm6000-stds.c: In function 'tm6000_set_audio_std':
media_build/v4l/tm6000-stds.c:341:10: warning: variable 'nicam_flag' set but not used [-Wunused-but-set-variable]
media_build/v4l/tm6000-video.c: In function 'get_next_buf':
media_build/v4l/tm6000-video.c:172:8: warning: variable 'outp' set but not used [-Wunused-but-set-variable]
media_build/v4l/tm6000-video.c: In function 'copy_streams':
media_build/v4l/tm6000-video.c:214:36: warning: variable 'c' set but not used [-Wunused-but-set-variable]
media_build/v4l/tm6000-input.c: In function 'tm6000_ir_urb_received':
media_build/v4l/tm6000-input.c:171:6: warning: variable 'rc' set but not used [-Wunused-but-set-variable]
media_build/v4l/usbvision-core.c: In function 'usbvision_decompress':
media_build/v4l/usbvision-core.c:604:23: warning: variable 'max_pos' set but not used [-Wunused-but-set-variable]
media_build/v4l/usbvision-core.c: In function 'usbvision_parse_compress':
media_build/v4l/usbvision-core.c:705:39: warning: variable 'rc' set but not used [-Wunused-but-set-variable]
media_build/v4l/usbvision-core.c:705:22: warning: variable 'bytes_per_pixel' set but not used [-Wunused-but-set-variable]
media_build/v4l/zoran_device.c: In function 'write_overlay_mask':
media_build/v4l/zoran_device.c:545:6: warning: variable 'reg' set but not used [-Wunused-but-set-variable]
media_build/v4l/go7007-v4l2.c: In function 'go7007_streamoff':
media_build/v4l/go7007-v4l2.c:79:6: warning: variable 'retval' set but not used [-Wunused-but-set-variable]

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l: fix compiler warnings

media_build/v4l/au0828-video.c: In function 'au0828_irq_callback':
media_build/v4l/au0828-video.c:123:6: warning: variable 'rc' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx23888-ir.c: In function 'pulse_clocks_to_clock_divider':
media_build/v4l/cx23888-ir.c:334:6: warning: variable 'rem' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25840-ir.c: In function 'pulse_clocks_to_clock_divider':
media_build/v4l/cx25840-ir.c:319:6: warning: variable 'rem' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25840-ir.c: In function 'cx25840_ir_tx_write':
media_build/v4l/cx25840-ir.c:863:21: warning: variable 'c' set but not used [-Wunused-but-set-variable]
media_build/v4l/em28xx-audio.c: In function 'snd_em28xx_hw_capture_params':
media_build/v4l/em28xx-audio.c:346:31: warning: variable 'format' set but not used [-Wunused-but-set-variable]
media_build/v4l/em28xx-audio.c:346:25: warning: variable 'rate' set but not used [-Wunused-but-set-variable]
media_build/v4l/em28xx-audio.c:346:15: warning: variable 'channels' set but not used [-Wunused-but-set-variable]
media_build/v4l/hdpvr-control.c: In function 'get_input_lines_info':
media_build/v4l/hdpvr-control.c:98:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/hdpvr-video.c: In function 'hdpvr_try_ctrl':
media_build/v4l/hdpvr-video.c:955:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/saa7134-video.c: In function 'saa7134_s_tuner':
media_build/v4l/saa7134-video.c:2030:6: warning: variable 'rx' set but not used [-Wunused-but-set-variable]
media_build/v4l/sn9c102_core.c: In function 'sn9c102_stream_interrupt':
media_build/v4l/sn9c102_core.c:998:7: warning: variable 'timeout' set but not used [-Wunused-but-set-variable]

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Janne Grunau <j@jannau.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] cx25821: fix compiler warnings

media_build/v4l/cx25821-core.c: In function 'cx_i2c_read_print':
media_build/v4l/cx25821-core.c:386:6: warning: variable 'value' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-core.c: In function 'cx25821_dev_setup':
media_build/v4l/cx25821-core.c:899:6: warning: variable 'io_size' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-core.c: In function 'cx25821_irq':
media_build/v4l/cx25821-core.c:1321:18: warning: variable 'pci_mask' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-i2c.c: In function 'cx25821_i2c_read':
media_build/v4l/cx25821-i2c.c:365:6: warning: variable 'retval' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-medusa-video.c: In function 'medusa_enable_bluefield_output':
media_build/v4l/cx25821-medusa-video.c:39:6: warning: variable 'ret_val' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-medusa-video.c: In function 'medusa_set_resolution':
media_build/v4l/cx25821-medusa-video.c:435:6: warning: variable 'ret_val' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-medusa-video.c: In function 'medusa_set_decoderduration':
media_build/v4l/cx25821-medusa-video.c:498:6: warning: variable 'ret_val' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-video.c: In function 'cx25821_dump_video_queue':
media_build/v4l/cx25821-video.c:116:25: warning: variable 'buf' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-video.c: In function 'cx25821_buffer_prepare':
media_build/v4l/cx25821-video.c:561:20: warning: variable 'line1_offset' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-video.c: In function 'video_ioctl_set':
media_build/v4l/cx25821-video.c:1834:6: warning: variable 'value' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-video-upstream.c: In function 'cx25821_upstream_irq':
media_build/v4l/cx25821-video-upstream.c:641:6: warning: variable 'msk_stat' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-video-upstream-ch2.c: In function 'cx25821_upstream_irq_ch2':
media_build/v4l/cx25821-video-upstream-ch2.c:591:6: warning: variable 'msk_stat' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx25821-audio-upstream.c: In function 'cx25821_upstream_irq_audio':
media_build/v4l/cx25821-audio-upstream.c:589:6: warning: variable 'msk_stat' set but not used [-Wunused-but-set-variable]

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ivtv/cx18: fix compiler warnings

media_build/v4l/cx18-alsa-main.c: In function 'cx18_alsa_exit':
media_build/v4l/cx18-alsa-main.c:282:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx18-mailbox.c: In function 'cx18_api_call':
media_build/v4l/cx18-mailbox.c:598:6: warning: variable 'state' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx18-alsa-pcm.c: In function 'snd_cx18_pcm_capture_open':
media_build/v4l/cx18-alsa-pcm.c:156:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx18-alsa-pcm.c: In function 'snd_cx18_pcm_capture_close':
media_build/v4l/cx18-alsa-pcm.c:202:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx18-alsa-pcm.c: In function 'snd_cx18_pcm_hw_params':
media_build/v4l/cx18-alsa-pcm.c:255:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/cx18-streams.c: In function 'cx18_stop_v4l2_encode_stream':
media_build/v4l/cx18-streams.c:983:16: warning: variable 'then' set but not used [-Wunused-but-set-variable]
media_build/v4l/ivtv-ioctl.c: In function 'ivtv_set_speed':
media_build/v4l/ivtv-ioctl.c:138:22: warning: variable 's' set but not used [-Wunused-but-set-variable]
media_build/v4l/ivtvfb.c: In function 'ivtvfb_init':
media_build/v4l/ivtvfb.c:1286:6: warning: variable 'err' set but not used [-Wunused-but-set-variable]
media_build/v4l/ivtvfb.c: In function 'ivtvfb_cleanup':
media_build/v4l/ivtvfb.c:1306:6: warning: variable 'err' set but not used [-Wunused-but-set-variable]

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] cx231xx: fix compiler warnings

v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-audio.c: In function ‘snd_cx231xx_hw_capture_params’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-audio.c:527:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-audio.c:526:31: warning: variable ‘format’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-audio.c:526:25: warning: variable ‘rate’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-audio.c:526:15: warning: variable ‘channels’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-audio.c: In function ‘snd_cx231xx_capture_trigger’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-audio.c:589:6: warning: variable ‘retval’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-video.c: In function ‘cx231xx_isoc_copy’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-video.c:331:17: warning: variable ‘outp’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-video.c: In function ‘cx231xx_bulk_copy’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-video.c:434:17: warning: variable ‘outp’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-video.c: In function ‘cx231xx_reset_video_buffer’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-video.c:704:7: warning: variable ‘outp’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c: In function ‘cx231xx_set_mode’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c:699:6: warning: variable ‘errCode’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c: In function ‘cx231xx_ep5_bulkout’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c:763:6: warning: variable ‘errCode’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c: In function ‘cx231xx_isoc_irq_callback’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c:800:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c: In function ‘cx231xx_bulk_irq_callback’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c:846:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c: In function ‘cx231xx_stop_TS1’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c:1234:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c: In function ‘cx231xx_start_TS1’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-core.c:1254:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_enable656’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:937:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_disable656’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:955:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_dump_HH_reg’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:1323:5: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_dump_SC_reg’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:1358:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_Setup_AFE_for_LowIF’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:1444:5: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_set_Colibri_For_LowIF’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:1504:5: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_set_DIF_bandpass’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:1559:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c: In function ‘cx231xx_gpio_i2c_write’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-avcore.c:3093:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-417.c: In function ‘cx231xx_initialize_codec’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-417.c:1098:9: warning: variable ‘data’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-417.c: In function ‘vidioc_streamon’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-417.c:1795:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-vbi.c: In function ‘cx231xx_isoc_vbi_copy’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-vbi.c:86:25: warning: variable ‘buf’ set but not used [-Wunused-but-set-variable]
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-vbi.c: In function ‘cx231xx_irq_vbi_callback’:
v4l-dvb-git/drivers/media/video/cx231xx/cx231xx-vbi.c:313:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

tty: Fix LED error return

3.4-rc introduced a regression when setting the LEDS. We do the right thing
but then return an error code.

Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=43144
Reported-by: Christian Casteyde
Signed-off-by: Alan Cox <alan@linux/intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

[media] dw2102: fix compile warnings

media_build/v4l/dw2102.c:151:13: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/dw2102.c:224:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/dw2102.c:279:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/dw2102.c:352:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/dw2102.c:435:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
media_build/v4l/dw2102.c:499:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m5mols: Add 3A lock control

Add control for locking automatic exposure, focus and white balance
adjustments. While at it, tidy up the data structure documentation.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m5mols: Add JPEG compression quality control

Add JPEG compression quality control for snapshot capture.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m5mols: Add exposure metering control

This patch adds V4L2_CID_EXPOSURE_METERING control which allows
to select the light metering mode for automatic exposure as one
of the following modes: spot (small area at the frame center),
center weighted and frame averaged.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m5mols: Add image stabilization control

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m5mols: Add wide dynamic range control

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m5mols: Add exposure bias control

Add integer menu control for exposure bias. The control value range is
-2.0 EV to +2.0 EV, in 0.5 EV steps.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m5mols: Add auto and preset white balance control

Replace the V4L2_CID_AUTO_WHITE_BALANCE control with its extended
version - V4L2_CID_AUTO_N_PRESET_WHITE_BALANCE so the white balance
presets feature is exposed to user land.

Acked-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m5mols: Add ISO sensitivity controls

Add controls for manual/auto ISO sensitivity.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m5mols: Use proper sensor mode for the controls

The parameters corresponding to the V4L controls can be reconfigured
only in associated M-5MOLS operation mode. Use struct v4l2_ctrl
priv field to assign the working mode to the controls which can be
modified only in certain conditions.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m5mols: Refactored controls handling

This patch is a prerequisite for the new controls addition. It consolidates
the control handling code, which is moved to m5mols_controls.c and
staticized. The controls initialization is reordered to better reflect
the control clusters and make the diffs smaller when new controls are added.
To make the code easier to follow when more controls is added use separate
set function for each control.

Rewrite the image effect registers handling.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m5mols: Convert macros to inline functions

Make to_sd and to_m5mols macros static inline functions
for better type safety.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: Add camera auto focus controls

Add following auto focus controls:

 - V4L2_CID_AUTO_FOCUS_START - single-shot auto focus start
 - V4L2_CID_AUTO_FOCUS_STOP -  single-shot auto focus stop
 - V4L2_CID_AUTO_FOCUS_STATUS - automatic focus status
 - V4L2_CID_AUTO_FOCUS_RANGE - automatic focus scan range selection

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: Add camera 3A lock control

The V4L2_CID_3A_LOCK bitmask control allows applications to pause
or resume the automatic exposure, focus and wite balance adjustments.
It can be used, for example, to lock the 3A adjustments right before
a still image is captured, for pre-focus, etc.
The applications can control each of the algorithms independently,
through a corresponding control bit, if driver allows that.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: Add camera scene mode control

Add control for the scene mode feature available in image sensor
with more advanced ISP firmware. The V4L2_CID_SCENE_MODE menu
control allows to select a set of parameters or a specific image
processing and capture control algorithm optimized for common
image capture conditions.

Signed-off-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: Add camera exposure metering control

The V4L2_CID_EXPOSURE_METERING control allows to determine
a method used by the camera for measuring the amount of light
available for automatic exposure.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: Add camera ISO sensitivity controls

Add ISO sensitivity and ISO auto/manual controls. The sensitivity
values are related to level of amplification of the analog signal
between image sensor and ADC. These controls allow to support sensors
exposing an interface to accept the ISO values directly.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: Add camera image stabilization control

Add V4L2_CID_IMAGE_STABILIZATION control for the camera image
stabilization feature. This control can be used to enable/disable
image stabilization. It might get converted to a menu control
in future if more options are needed.

Signed-off-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: Add camera wide dynamic range control

Add V4L2_CID_WIDE_DYNAMIC_RANGE camera class control for the
camera wide dynamic range (WDR, HDR) feature. This control
can be used to enable/disable wide dynamic range. It might
get converted to a menu control in future if more options
are needed.

Signed-off-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: Add an extended camera white balance control

This patch adds V4L2_CID_AUTO_N_PRESET_WHITE_BALANCE control which is
an extended version of the V4L2_CID_AUTO_WHITE_BALANCE control,
including white balance presets. The following presets are defined:

 - V4L2_WHITE_BALANCE_INCANDESCENT,
 - V4L2_WHITE_BALANCE_FLUORESCENT,
 - V4L2_WHITE_BALANCE_FLUORESCENT_H,
 - V4L2_WHITE_BALANCE_HORIZON,
 - V4L2_WHITE_BALANCE_DAYLIGHT,
 - V4L2_WHITE_BALANCE_FLASH,
 - V4L2_WHITE_BALANCE_CLOUDY,
 - V4L2_WHITE_BALANCE_SHADE.

Signed-off-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: Add camera exposure bias control

The camera may in some conditions incorrectly determine the exposure,
and a manual automatic exposure correction may be needed. This patch
adds V4L2_CID_AUTO_EXPOSURE_BIAS control which allows to add some
offset in the automatic exposure control loop, to compensate for
frame under- or over-exposure.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: Add helper function for standard integer menu controls

This patch adds v4l2_ctrl_new_int_menu() helper function which can be used
in drivers for creating standard integer menu control with driver-specific
menu item list. It is similar to v4l2_ctrl_new_std_menu(), except it doesn't
have a mask parameter and an additional qmenu parameter allows passing
an array of signed 64-bit integers as the menu item list.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Tested-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L: Extend V4L2_CID_COLORFX with more image effects

This patch adds definition of additional color effects:

 - V4L2_COLORFX_AQUA,
 - V4L2_COLORFX_ART_FREEZE,
 - V4L2_COLORFX_SILHOUETTE,
 - V4L2_COLORFX_SOLARIZATION,
 - V4L2_COLORFX_ANTIQUE,
 - V4L2_COLORFX_SET_CBCR.

The new V4L2_COLORFX_CBCR control is added to allow setting
the fixed Cb, Cr values that replace chroma Cb/Cr coefficients
in case of V4L2_COLORFX_SET_CBCR effect.

Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] radio-si470x-usb: remove autosuspend, implement suspend/resume

The radio-si470x-usb driver supported both autosuspend and it stopped the
radio the moment the last user of the radio device closed it. However, that
was very confusing since if you play the audio from the device (e.g. through
arecord -D ... | aplay) then no sound would play unless you had the radio
device open at the same time, even though there is no need to do anything
with that node.

On the other hand, the actual suspend/resume functions didn't do anything,
which would fail if you *did* have the radio node open at that time.

So:

- remove autosuspend (bad idea in general for USB radio devices)
- move the start/stop out of the open/release functions into the resume/suspend
  functions.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] radio-si470x-common.c: remove unnecessary kernel log spam

There is no need to report an error in the log, you are already returning
that error to userspace after all.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] si470x: add control event support and more v4l2 compliancy fixes

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] si470x: Clean up, introduce the control framework

This cleans up the code and si470x now uses the proper v4l2 frameworks
and passes most of the v4l2-compliance tests.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l: v4l2-ctrls: moves the forward declaration of struct file

This fixes the following warning:

In file included from drivers/media/video/v4l2-subdev.c:29:
include/media/v4l2-ctrls.h:501: warning: 'struct file' declared inside
parameter list
include/media/v4l2-ctrls.h:501: warning: its scope is only this
definition or declaration, which is probably not what you want
include/media/v4l2-ctrls.h:509: warning: 'struct file' declared inside
parameter list

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mt9v032: Correct the logic for the auto-exposure setting

The driver uses the ctrl value passed in as a bool to determine whether
to enable auto-exposure, but the auto-exposure setting is defined as an
enum where AUTO has a value of 0 and MANUAL has a value of 1. This leads
to a reversed logic where if you send in AUTO, it actually sets manual
exposure and vice-versa.

Signed-off-by: Kartik Mohta <kartikmohta@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mt9m032: use the available subdev pointer, don't re-calculate it

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mt9m032: fix compilation breakage

Fix the following compilation failure:

linux-2.6/drivers/media/video/mt9m032.c: In function '__mt9m032_get_pad_crop':
linux-2.6/drivers/media/video/mt9m032.c:337: error: implicit declaration of function 'v4l2_subdev_get_try_crop'
linux-2.6/drivers/media/video/mt9m032.c:337: warning: return makes pointer from integer without a cast
linux-2.6/drivers/media/video/mt9m032.c: In function '__mt9m032_get_pad_format':
linux-2.6/drivers/media/video/mt9m032.c:359: error: implicit declaration of function 'v4l2_subdev_get_try_format'
linux-2.6/drivers/media/video/mt9m032.c:359: warning: return makes pointer from integer without a cast
linux-2.6/drivers/media/video/mt9m032.c: In function 'mt9m032_probe':
linux-2.6/drivers/media/video/mt9m032.c:767: error: 'struct v4l2_subdev' has no member named 'entity'
linux-2.6/drivers/media/video/mt9m032.c:826: error: 'struct v4l2_subdev' has no member named 'entity'
linux-2.6/drivers/media/video/mt9m032.c: In function 'mt9m032_remove':
linux-2.6/drivers/media/video/mt9m032.c:842: error: 'struct v4l2_subdev' has no member named 'entity'
make[4]: *** [drivers/media/video/mt9m032.o] Error 1

by adding a dependency on VIDEO_V4L2_SUBDEV_API.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mt9m032: fix two dead-locks

Fix a copy-paste typo and a nested locking function call in mt9m032.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mt9p031: Implement black level compensation control

Add four new controls to configure black level compensation (BLC):

- V4L2_CID_BLC_AUTO selects between manual and auto BLC
- V4L2_CID_BLC_TARGET_LEVEL sets the target level for auto BLC
- V4L2_CID_BLC_ANALOG_OFFSET sets the analog offset for manual BLC
- V4L2_CID_BLC_DIGITAL_OFFSET sets the digital offset for manual BLC

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mt9p031: Replace the reset board callback by a GPIO number

Use the GPIO from the sensor driver instead of calling back to board
code.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mt9p031: Identify color/mono models using I2C device name

Instead of passing a color/monochrome flag through platform data, rely
on the I2C device name to identify the chip model.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>