ath9k : few rate control clean ups

Remove some obvious looking dead code and rename few functions

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Revert "mac80211: temporarily disable reorder release timer"

This reverts enables the reorder release timer once again.

The issues laid out in:
<http://www.spinics.net/lists/linux-wireless/msg57214.html>

Have been addressed by:
mac80211: serialize rx path workers
mac80211: ignore PSM bit of reordered frames

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: serialize rx path workers

This patch addresses the issue of serialization between
the main rx path and various reorder release timers.

<http://www.spinics.net/lists/linux-wireless/msg57214.html>

It converts the previously local "frames" queue into
a global rx queue [rx_skb_queue]. This way, everyone
(be it the main rx-path or some reorder release timeout)
can add frames to it.

Only one active rx handler worker [ieee80211_rx_handlers]
is needed. All other threads which have lost the race of
"runnning_rx_handler" can now simply "return", knowing that
the thread who had the "edge" will also take care of their
workload.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix beacon restart on channel change

Restart the beacon timers only if the beacon
was already configured. Otherwise beacons timers
are restarted unnecessarily in unassociated state too.

Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Revert "ath9k: Parse DTIM period from mac80211"

This reverts commit 0ce3bcfc84900a64347b0fe1140229bd81314008.

Event though with the above commit we obtain the configured DTIM period
from the AP rather than always hardcoding it to '1', this seems to cause
problems under the following scenarios:
* Preventing association with broken AP's
* Adds latency in roaming
So its better to always use the safe value of '1' for dtim period

Cc: Jouni Malinen <Jouni.Malinen@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: fix transposition of words in printk

Fixes the misplaced article in the following:

"cfg80211: Updating information on frequency 5785 MHz for
    20 a MHz width channel with regulatory rule:"

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Fix mesh portal communication with other mesh nodes.

Fixed a bug where if a mesh interface has a different MAC address from its bridge
interface, then it would not be able to send data traffic to any other mesh node.
This also adds support for communication between mesh nodes and external bridged
nodes by using a 6 address format if the source is a node within the mesh and the
destination is an external node proxied by a mesh portal.

Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: fix dma descriptor rx error bit parsing

An Rx DMA descriptor can have multiple error bits set, and some error
bits (e.g. MIC failure) are filtered by the driver based on other criteria.
Remove the 'else' in various error bit checks so that all error information
is properly passed to the driver.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Move LED/RFKILL code to htc_drv_gpio.c

And add the copyright/license header.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Fix fast channel change

When returning to the operating channel, a full HW
reset has to be done instead of a fast channel change.
Since sw_scan_complete() is called after the config() call for the
home channel, we end up doing a FCC. Fix this issue by checking
the OFFCHANNEL flag to determine FCC.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Handle FATAL events

The device has to be reset when a FATAL event is received.
Not doing so would leave the card in a non-working state.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Move work cancellation outside of mutex

There is no need to lock the various work cancellation
calls. This will be helpful when handling FATAL events.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Handle pending URBs properly

When doing a channel change, the pending URBs have to be killed
properly on calling htc_stop().

This fixes the probe response timeout seen when sending UDP traffic at
a high rate and running background scan at the same time.

Cc: stable <stable@kernel.org>
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Few clean ups in beacon config parameters

Some minor clean ups in assigning values to beacon config parameters

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: ignore PSM bit of reordered frames

This patch tackles one of the problems of my
reorder release timer patch from August.

<http://www.spinics.net/lists/linux-wireless/msg57214.html>
=>
What if the reorder release triggers and ap_sta_ps_end
(called by ieee80211_rx_h_sta_process) accidentally clears
the WLAN_STA_PS_STA flag, because 100ms ago - when the STA
was still active - frames were put into the reorder buffer.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix comment about removed spinlock

The comment doesn't match the code anymore. Fix that.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Remove unused interface spinlock

Since the last user of intf->lock is gone we can safely remove it.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Simplify intf->delayed_flags locking

Instead of protecting delayed_flags with a spinlock use atomic bitops to
make the code more readable.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Remove superfluous assignment of mpdu_density

The tx desciptor already gets initialized to 0. Hence, there's no need
to explicitly assign 0 to mpdu_density here.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix panic on frame padding for rt2800 usb devices

Backtrace:
  rt2800usb_write_tx_data
  rt2x00queue_write_tx_frame
  rt2x00mac_tx
  invoke_tx_handlers
  __ieee80211_tx
  ieee80211_tx
  virt_to_head_page
  ieee80211_xmit
  ieee80211_tx_skb
  ieee80211_scan_work
  schedule
  ieee80211_scan_work
  process_one_work
  ...

It tried to expand the skb past it's end using skb_put. So I replaced it
with a call to skb_padto, which takes the issue into account.

Signed-off-by: Ismael Luceno <ismael.luceno@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix pointer errors.

Fix some pointer errors in the various calls to memcpy, memset and memmove.

Although none of these errors are fatal (the expression used now results in
the same pointer value) it is better to use the proper expression.
All errors are having to deal with arrays.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: remove intf->mac field.

The mac field of the rt2x00_intf structure is written to once and used
twice. In both these uses the mac address is available via other means.

Remove this field as it does not appear to be necessary.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Remove intf->bssid field.

The bssid field in struct rt2x00_intf is only written to once, and is
never read from.

Remove this field, as it appears to not be needed.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: allow txstatus_fifo w/o txstatus_tasklet

When DRIVER_REQUIRE_TXSTATUS_FIFO is set, intialize the
txstatus_fifo, but initialize rt2x00dev->txstatus_tasklet
only when both DRIVER_REQUIRE_TXSTATUS_FIFO and
rt2x00dev->ops->lib->txstatus_tasklet are set.

This allows the txstatus_fifo to be used by rt2800usb which
does not use txstatus_tasklet.

Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: simplify txstatus_fifo handling

Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

carl9170: fix usb pm suspend->resume woes

This patch revamps some common code-paths which are
shared between (re-)initialization and suspend/resume
subroutines. It also adds some helpful comments
about quirks and associated difficulties.

It's quite big, but it should fix #25382:
<https://bugzilla.kernel.org/show_bug.cgi?id=25382>

And hopefully the code is robust enough to deal with
all possible suspend/resume scenarios without requiring
the user to do any sort of manual and possibly
dangerous work.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

carl9170: reduce channel change delay

By removing two "safety" msleeps (and an echo nop), the
channel change delay is effectively halved. Previously,
the delay could be as long as 260 ms and the device
could not go off-channel without risking to miss the
next DTIM beacon [interval ~307 ms].

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

carl9170: add missing return-value check

This patch adds a forgotten bail-out path.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: fix cycle counter inconsistent locking

ath5k_reset is called from process context and takes the cc_lock
with plain spin_lock(), but cc_lock can also be taken from tasklets
in softirq context.  Thus we need to at least use spin_lock_bh.

This fixes the following lockdep warning:

[   19.967874] sky2 0000:01:00.0: eth0: enabling interface
[   19.982761] ieee80211 phy0: device now idle
[   20.904809] NET: Registered protocol family 17
[   21.243857] ieee80211 phy0: device no longer idle - scanning
[   21.404343]
[   21.404346] =================================
[   21.404450] [ INFO: inconsistent lock state ]
[   21.404518] 2.6.37-rc7-wl+ #242
[   21.404582] ---------------------------------
[   21.404650] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
[   21.404721] kworker/u:4/982 [HC0[0]:SC1[3]:HE1:SE0] takes:
[   21.404792]  (&(&common->cc_lock)->rlock){+.?...}, at: [<f8115780>] ath5k_ani_calibration+0x29/0x5d9 [ath5k]
[   21.405011] {SOFTIRQ-ON-W} state was registered at:
[   21.405011]   [<c105cadd>] __lock_acquire+0x62f/0x13c1
[   21.405011]   [<c105d944>] lock_acquire+0xd5/0xf1
[   21.405011]   [<c12c978d>] _raw_spin_lock+0x45/0x72
[   21.405011]   [<f8111533>] ath5k_reset+0x2c0/0x349 [ath5k]
[   21.405011]   [<f8111a7a>] ath5k_start+0xb8/0x139 [ath5k]
[   21.405011]   [<f849c714>] ieee80211_do_open+0x13f/0x819 [mac80211]
[   21.405011]   [<f849ce51>] ieee80211_open+0x63/0x66 [mac80211]
[   21.405011]   [<c1258b2e>] __dev_open+0x8d/0xb6
[   21.405011]   [<c1255c64>] __dev_change_flags+0x9d/0x114
[   21.405011]   [<c1258a75>] dev_change_flags+0x18/0x44
[   21.405011]   [<c1262990>] do_setlink+0x23f/0x521
[   21.405011]   [<c1262d58>] rtnl_setlink+0xe6/0xea
[   21.405011]   [<c126347c>] rtnetlink_rcv_msg+0x18a/0x1a0
[   21.405011]   [<c126d5f0>] netlink_rcv_skb+0x35/0x7b
[   21.405011]   [<c12632eb>] rtnetlink_rcv+0x20/0x27
[   21.405011]   [<c126d370>] netlink_unicast+0x1bb/0x21e
[   21.405011]   [<c126db21>] netlink_sendmsg+0x23b/0x288
[   21.405011]   [<c124823c>] sock_sendmsg+0xac/0xc4
[   21.405011]   [<c1248680>] sys_sendmsg+0x152/0x1a2
[   21.405011]   [<c1249b0d>] sys_socketcall+0x214/0x275
[   21.405011]   [<c10029d0>] sysenter_do_call+0x12/0x36
[   21.405011] irq event stamp: 138032
[   21.405011] hardirqs last  enabled at (138032): [<c12ca252>] _raw_spin_unlock_irqrestore+0x3b/0x5e
[   21.405011] hardirqs last disabled at (138031): [<c12c98cc>] _raw_spin_lock_irqsave+0x18/0x7e
[   21.405011] softirqs last  enabled at (138024): [<f84a570e>] ieee80211_tx_skb+0x47/0x49 [mac80211]
[   21.405011] softirqs last disabled at (138027): [<c100452b>] do_softirq+0x63/0xb4
[   21.405011]
[   21.405011] other info that might help us debug this:
[   21.405011] 3 locks held by kworker/u:4/982:
[   21.405011]  #0:  (name){+.+.+.}, at: [<c1046158>] process_one_work+0x1b8/0x41b
[   21.405011]  #1:  ((&(&local->scan_work)->work)){+.+.+.}, at: [<c1046158>] process_one_work+0x1b8/0x41b
[   21.405011]  #2:  (&local->mtx){+.+.+.}, at: [<f84920fb>] ieee80211_scan_work+0x32/0x4a4 [mac80211]
[   21.405011]
[   21.405011] stack backtrace:
[   21.405011] Pid: 982, comm: kworker/u:4 Not tainted 2.6.37-rc7-wl+ #242
[   21.405011] Call Trace:
[   21.405011]  [<c12c6e68>] ? printk+0x1d/0x25
[   21.405011]  [<c105a742>] print_usage_bug+0x181/0x18b
[   21.405011]  [<c105b196>] ? check_usage_forwards+0x0/0xb6
[   21.405011]  [<c105a9ec>] mark_lock+0x2a0/0x4aa
[   21.405011]  [<c1059f6d>] ? trace_hardirqs_off+0xb/0xd
[   21.405011]  [<c105ca68>] __lock_acquire+0x5ba/0x13c1
[   21.405011]  [<c1059eed>] ? trace_hardirqs_off_caller+0x18/0x8d
[   21.405011]  [<c1059f6d>] ? trace_hardirqs_off+0xb/0xd
[   21.405011]  [<c1050411>] ? local_clock+0x2c/0x4f
[   21.405011]  [<c1059e00>] ? save_trace+0x2/0xa0
[   21.405011]  [<c105ac39>] ? mark_held_locks+0x43/0x5b
[   21.405011]  [<c12ca252>] ? _raw_spin_unlock_irqrestore+0x3b/0x5e
[   21.405011]  [<f8115780>] ? ath5k_ani_calibration+0x29/0x5d9 [ath5k]
[   21.405011]  [<c105d944>] lock_acquire+0xd5/0xf1
[   21.405011]  [<f8115780>] ? ath5k_ani_calibration+0x29/0x5d9 [ath5k]
[   21.405011]  [<c12c9b1a>] _raw_spin_lock_bh+0x4a/0x77
[   21.405011]  [<f8115780>] ? ath5k_ani_calibration+0x29/0x5d9 [ath5k]
[   21.405011]  [<f8115780>] ath5k_ani_calibration+0x29/0x5d9 [ath5k]
[   21.405011]  [<c105ac39>] ? mark_held_locks+0x43/0x5b
[   21.405011]  [<f8113496>] ath5k_tasklet_ani+0x1d/0x27 [ath5k]
[   21.405011]  [<c1037304>] tasklet_action+0x96/0x137
[   21.405011]  [<c10379b5>] __do_softirq+0xde/0x1c3
[   21.405011]  [<c10b0cef>] ? arch_get_unmapped_area_topdown+0x3b/0x127
[   21.405011]  [<c10378d7>] ? __do_softirq+0x0/0x1c3
[   21.405011]  <IRQ>  [<c1036dee>] ? irq_exit+0x3d/0x49
[   21.405011]  [<c1003b4f>] ? do_IRQ+0x98/0xac
[   21.405011]  [<c1002eee>] ? common_interrupt+0x2e/0x34
[   21.405011]  [<c103007b>] ? sys_unshare+0x57/0x226
[   21.405011]  [<c1047fee>] ? queue_delayed_work+0x1/0x27
[   21.405011]  [<f84a83a0>] ? ieee80211_queue_delayed_work+0x2e/0x33 [mac80211]
[   21.405011]  [<f8492528>] ? ieee80211_scan_work+0x45f/0x4a4 [mac80211]
[   21.405011]  [<c104620e>] ? process_one_work+0x26e/0x41b
[   21.405011]  [<c1046158>] ? process_one_work+0x1b8/0x41b
[   21.405011]  [<f84920c9>] ? ieee80211_scan_work+0x0/0x4a4 [mac80211]
[   21.405011]  [<c10466b6>] ? worker_thread+0x18a/0x2a5
[   21.405011]  [<c12ca25e>] ? _raw_spin_unlock_irqrestore+0x47/0x5e
[   21.405011]  [<c104652c>] ? worker_thread+0x0/0x2a5
[   21.405011]  [<c104abe7>] ? kthread+0x67/0x6c
[   21.405011]  [<c104ab80>] ? kthread+0x0/0x6c
[   21.405011]  [<c1002efa>] ? kernel_thread_helper+0x6/0x10

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix spur mitigation no-spur case for AR9002

For the AR9002, the spur frequency read from the EEPROM is mangled
before being compared against AR_NO_SPUR.  This results in the driver
trying to set up the spur mitigation for bogus spurs, rather than
cleanly breaking out.

Signed-off-by: Brian Prodoehl <bprodoehl@nomadio.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

airo: use simple_write_to_buffer

Simplify write file operation for /proc files by using
simple_write_to_buffer().

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: spin_lock_bh is not required within tasklet context.

Disabling BH is not required while running from a tasklet context
and so replace spin_lock_bh with just spin_lock.

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: fix scan tx antenna setting on 5Ghz band

Looks that we do not set correctly antennas when scanning
on 5Ghz band and when bluetooth is enabled, because
priv->cfg->scan_tx_antennas[band] is only defined for
IEEE80211_BAND_2GHZ.

To fix we check band before limiting antennas to first one.
This allow to remove hard coded cfg->scan_tx_antennas[band].

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Move mac80211 functions into new file

Move mac80211 functions into new file mac80211-ops.c to have a better
separation and to make base.c smaller.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'wireless-next-2.6' of git://git./linux/kernel/git/iwlwifi/iwlwifi-2.6

Merge branch 'master' of /linux/kernel/git/padovan/bluetooth-next-2.6

iwlwifi: remove reference to Gen2

The correct name should be used for the newer devices, remove
reference to Gen2

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn: fix FH error

# iw wlan0 interface add moni0 type monitor flags control
# ip link set moni0 up

causes a continuous spew of FH_ERROR from the
device. Fix this by not setting the CTL2HOST
filter by itself -- CTL + promisc works fine.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

iwlwifi: remove extra string

For "led_mode" module parameters, string "led_mode" is duplicated twice,
remove one.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

Bluetooth: Improve handling of HCI control channel in bind

Does not allow any channel different of HCI_CHANNEL_RAW and
HCI_CHANNEL_CONTROL to bind.

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Fix __hci_request synchronization for hci_open_dev

The initialization function used by hci_open_dev (hci_init_req) sends
many different HCI commands. The __hci_request function should only
return when all of these commands have completed (or a timeout occurs).
Several of these commands cause hci_req_complete to be called which
causes __hci_request to return prematurely.

This patch fixes the issue by adding a new hdev->req_last_cmd variable
which is set during the initialization procedure. The hci_req_complete
function will no longer mark the request as complete until the command
matching hdev->req_last_cmd completes.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Add management events for controller addition & removal

This patch adds Bluetooth Management interface events for controller
addition and removal. The events correspond to the existing HCI_DEV_REG
and HCI_DEV_UNREG stack internal events.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Add read_info management command

This patch implements the read_info command which is used to fetch basic
info about an adapter.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Add read_index_list management command

This patch implements the read_index_list command through which
userspace can get a list of current adapter indices.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Add read_version management command

This patch implements the initial read_version command that userspace
will use before any other management interface operations.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Add error handling for managment command handlers

The command handlers for bluetooth management messaging should be able
to report errors (such as memory allocation failures) to the higher
levels in the call stack.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

rtlwifi: Fix large packet issue

An RX buffer is set to 9100 bytes to receive 8K AMSDU; however, an skb
of this size fails in the kernel.

Signed-off-by: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: cleanup select_queue

There's a redundant rcu_read_lock/unlock pair, a
redundant variable, and a few redundant accesses
to the 1d_to_ac array. Fix this to make the code
neater and easier to follow.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Reset keycache on resume

It looks like some hardware registers are left into undefined state
after suspend/resume. At minimum, this can cause odd issues related to
key cache and hardware trying to encrypt/decrypt frames unexpectedly.
This seems to happen even when there is no keys configured, i.e., hardware
can end up touching TX frames just based of invalid key cache context
even if the driver is not asking a specific entry to be used. In
addition, RX can likely be affected. This patch fixes this issue.

Signed-off-by: Jouni Malinen <Jouni.Malinen@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192ce: Fix driver problem when radio switch off at module load

If the radio enable switch is off when the driver is loaded, it is not
possible to get radio output until the driver is unloaded and reloaded
with the switch on.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rndis_wlan: add support for set_power_mgmt

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rndis_wlan: add support for set_cqm_rssi_config

Device poller already reads current RSSI, so add support for
set_cqm_rssi_config there.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rndis_wlan: remove unused variable from priv structure

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rndis_wlan: constify rndis_config_ops

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rndis_wlan: turn radio off before interface is bring up

Radio should be off when interface is down.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rndis_wlan: do not set default_key if not WEP key

rndis_set_default_key did call add_wep_key to set default key on device, even
if key is WPA. This caused rndis_wlan not work with wpa_supplicant in nl80211
mode (causing disconnect from AP).

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rndis_wlan: scanning, workaround device returning incorrect bssid-list item count.

Sometimes device returns wrong number of items in bssid-list. Appears that
some specific beacons trigger this problem and leads to very poor scanning
results. Workaround by ignoring num_items received from device and walkthrough
full bssid-list buffer.

v2: Fix buffer range checks and reading next item length. Old code read
    behind buffer on last item but didn't use those values as 'count' would
    also reach zero. Also fix resizing of buffer if device has larger buffer,
    old code assumed that BSSID-list OID would return same buffer size
    when it really can return yet another new larger length.

Tested-by: Luís Picciochi <Pitxyoki@gmail.com>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: enable support for PHYs rev 3 and higher

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: update 2056 radio on channel switch on rev3+

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: use correct channel tables for rev4+

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: avoid PHY hangs for rev 3 and 4

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: add init tables for 2056 radio

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: implement radio 2056 init steps

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: use correct firmware for newer cores

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Fix bug in eeprom data length validation for AR9485

The size of the eeprom data is 1088 bytes for AR9485. But
a sanity check is done against 4K which would result in a
'potential read past the end of the buffer' smatch complaint.

Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Use helper function to get eeprom mode from channel

Introduce a helper function to get the EEPROM mode from channel and remove
multiple similar switch statements. Also since it's now easy to get the EEPROM
mode from the channel, use them inside the functions which need it, instead of
passing a redundant ee_mode parameter.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Remove ATH5K_INI_RFGAIN defines, use band instead

Remove redundant defines.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Track current TX power separately from max TX power

Add a new variable to keep track of the currently configured tx power. Before
max_pwr was re-used for keeping the maximum allowed power as well as the
current configuration. Doing a min() on it allows you to lower the txpower, but
how would you be able to make it higher again?

This patch fixes that by adding a new variable ah_cur_pwr which is used instead
of txp_max_pwr to keep the current configuration. txp_max_pwr is used to check
if we are within the limits.

Another problem fixed by this patch is that it avoids setting a zero txpower
when things are initialized first and the current power is not yet set.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Separate powertable setup and writing

And rename functions which write the powertable to make it clearer.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Simplify powertable recalculation

Let ath5k_hw_txpower() decide if it can re-use the powertable or if it has to
be recalculated instead of passing a 'fast' flag from the outside.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: unlock on error path in ath9k_change_interface()

There is a missing unlock when we hit the "No beacon slot available"
error condition.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Use pci_pcie_cap()

Use function pci_pcie_cap() instead of accessing struct member directly.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Use pci_is_pcie()

Use function pci_is_pcie() instead of accessing struct member directly.

CC: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Use pci_is_pcie()

Use function pci_is_pcie() instead of accessing struct member directly.

CC: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Use pci_is_pcie()

Use function pci_is_pcie() instead of accessing struct member directly.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb: Use pci_is_pcie()

Use function pci_is_pcie() instead of accessing struct member directly.

CC: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl12xx: remove unnecessary import

No function declared in gpio.h is used here.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251: remove unnecessary import

No function declared in gpio.h is used here.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix aphy / wiphy idle mismatch

ath9k supports its own set of virtual wiphys, and it uses
the mac80211 idle notifications to know when a device needs
to be idle or not. We recently changed ath9k to force idle
on driver stop() and on resume but forgot to take into account
ath9k's own virtual wiphy idle states. These are used internally
by ath9k to check if the device's radio should be powered down
on each idle call. Without this change its possible that the
device could have been forced off but the virtual wiphy idle
was left on.

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix warnings on card removal

The recently added warning message on power change failure
is not needed on device removal.

ath: Failed to wakeup in 500us
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/hw.c:1618
ath9k_hw_setpower+0x61f/0x630 [ath9k_hw]()
Hardware name: 64756D6
Pid: 540, comm: kworker/u:3 Not tainted 2.6.37-rc6-wl #37
Call Trace:
 [<ffffffff810501aa>] warn_slowpath_common+0x7a/0xb0
 [<ffffffffa056e280>] ? ath9k_iowrite32+0x0/0x90 [ath9k]
 [<ffffffff810501f5>] warn_slowpath_null+0x15/0x20
 [<ffffffffa05226ef>] ath9k_hw_setpower+0x61f/0x630 [ath9k_hw]
 [<ffffffffa05700e5>] ath9k_ps_wakeup+0x85/0xd0 [ath9k]
 [<ffffffffa0570685>] ath9k_configure_filter+0x25/0x80 [ath9k]
 [<ffffffffa04dde43>] ieee80211_configure_filter+0x133/0x190 [mac80211]
 [<ffffffffa04ee502>] ieee80211_do_stop+0x132/0x540 [mac80211]
 [<ffffffff813466ff>] ? _raw_spin_unlock_bh+0x1f/0x30
 [<ffffffff812b6923>] ? dev_deactivate+0x1c3/0x1e0
 [<ffffffffa04ee925>] ieee80211_stop+0x15/0x20 [mac80211]
 [<ffffffff8129d1b6>] __dev_close+0x56/0x90

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Fix warning on device removal

The commit "ath9k_hw: warn if we cannot change the power to the chip"
introduced a new warning to indicate chip powerup failures, but this
is not required for devices that have been removed. Handle USB device
removal properly by checking for unplugged status.

For PCI devices, this warning will still be seen when the card is pulled
out, not sure how to check for card removal.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl818x: move rtl8180 and rtl8187 to separate subdirectories

These drivers share one header file, but nothing else.  Worse, both
drivers use the rtl8225 part with different register settings.  The
results has been some ugly naming -- let's simplify that.

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>

rtlwifi: use alloc_workqueue

create_workqueue is deprecated.  The workqueue usage does not seem to
demand any special treatment, so do not set any flags either.

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Tejun Heo <tj@kernel.org>

ath9k: do not limit the chainmask to 1 for legacy mode

Restricting the chainmask to 1 for legacy mode disables useful features
such as MRC, and it reduces the available transmit power.
I can't think of a good reason to do this in legacy mode, so let's just
get rid of that code.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: fix PA predistortion HT40 mask

The commit 'ath9k_hw: Disable PAPRD for rates with low Tx power' changed
the code that sets the PAPRD rate masks to use only either the HT20 mask
or the HT40 mask. This is wrong, as the hardware can still use HT20 rates
even when configured for HT40, and the operating channel mode does not
affect PAPRD operation.
The register for the HT40 rate mask is applied as a mask on top of the
other registers to selectively disable PAPRD for specific rates on HT40
packets only.
This patch changes the code back to the old behavior which matches the
intended use of these registers. While with current cards this should not
make any practical difference (according to Atheros, the HT20 and HT40
mask should always be equal), it is more correct that way, and maybe
the HT40 mask will be used for some rare corner cases in the future.

Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix potentially redundant skb data copying

When an skb is shared, it needs to be duplicated, along with its data buffer.
If the skb does not have enough headroom, using skb_copy might cause the data
buffer to be copied twice (once by skb_copy and once by pskb_expand_head).
Fix this by using skb_clone initially and letting ieee80211_skb_resize sort
out the rest.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: skip unnecessary pskb_expand_head calls

If the skb is not cloned and we don't need any extra headroom, there
is no point in reallocating the skb head.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix initialization of skb->cb in ieee80211_subif_start_xmit

The change 'mac80211: Fix BUG in pskb_expand_head when transmitting shared skbs'
added a check for copying the skb if it's shared, however the tx info variable
still points at the cb of the old skb

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251: wl12xx_get_platform_data() returns an ERR_PTR

wl12xx_get_platform_data() returns an ERR_PTR on failure and it never
returns a NULL.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Fix use of mutex in interrupt code

A previous conversion from semaphoreto mutexes missed the fact that one
of the semaphores was used in interrupt code. Fixed by changing to
a spinlock.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

MAINTAINERS: Fix typo in rtl8192ce entry

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Properly initialize channel table for 2GHz

ath9k channel table for 2Ghz does not seems to initialize the 'band'
parameter.Though it does not seems to cause any visible issue it looks
odd when we initialize the 'band' parameter for 5Ghz channel table while
not so for 2Ghz.

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl8192ce: Fix typo in Kconfig description

Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: remove baseband rfsilent support

When rfkill is enabled, ath9k_hw unnecessarily configured the baseband to
turn off based on GPIO input, however that code was hardcoded to GPIO 0
instead of ah->rfkill_gpio.
Since ath9k uses software rfkill anyway, this code is completely unnecessary
and should be removed in case anything else ever uses GPIO 0.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix queue depth check for forming new aggregates

To improve aggregation length, there should not be more than two fully formed
A-MPDU frames in the hardware queue. To ensure this, the code checks the tx
queue length before forming new A-MPDUs. This can reduce the throughput (or
maybe even starve out A-MPDU traffic) when too many non-aggregated frames are
in the queue.
Fix this by keeping track of pending A-MPDU frames (even when they're sent out
as single frames), but exclude rate control probing frames to improve
performance.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtl8192ce: drop 'rtl8192c-' prefix from files

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>

mac80211: Remove unused third address from mesh address extension header.

The Mesh Control header only includes 0, 1 or 2 addresses. If there is
one address, it should be interpreted as Address 4.  If there are 2,
they are interpreted as Addresses 5 and 6 (Address 4 being the 4th
address in the 802.11 header).

The address extension used to hold up to 3 addresses instead of the current 2.
I'm not sure which draft version changed this, but it is very unlikely that it
will change again given the state of the approval process of this draft.  See
section 7.1.3.6.3 in current draft (8.0).

Also, note that the extra address that I'm removing was not being used, so this
change has no effect on over-the-air frame formats.  But I thought I better
remove it before someone does start using it.

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Set available antenna information for cfg80211

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

nl80211: Export available antennas

Export the information which antennas are available for configuration as TX or
RX antennas via nl80211.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: Separate available antennas for RX and TX

As has been pointed out by Daniel Halperin some devices (e.g. Intel IWL5100)
can only TX from a subset of RX antennas, so use separate availability masks
for RX and TX.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>