ath10k: add a_sle32_to_cpu()

Copy a_sle32_to_cpu() from ath6kl so that we can easily handle signed __le32
values. This is needed in struct wmi_pdev_tpc_config_event.

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k: split an unnecessary long line

from checkpatch:

drivers/net/wireless/ath/ath10k/mac.c:1113: line over 90 characters

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k: fix whitespace usage

checkpatch found:

drivers/net/wireless/ath/ath10k/core.c:574: Blank lines aren't necessary before a close brace '}'
drivers/net/wireless/ath/ath10k/mac.c:4067: Missing a blank line after declarations
drivers/net/wireless/ath/ath10k/mac.c:4083: Missing a blank line after declarations
drivers/net/wireless/ath/ath10k/mac.c:4084: spaces required around that '>>=' (ctx:WxV)
drivers/net/wireless/ath/ath10k/pci.c:1507: Missing a blank line after declarations

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k: remove void function return statements

drivers/net/wireless/ath/ath10k/wmi.c:3023: void function return statements are not generally useful

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k: brace style fixes

drivers/net/wireless/ath/ath10k/htt_tx.c:457: braces {} are not necessary for single statement blocks
drivers/net/wireless/ath/ath10k/htt_tx.c:545: braces {} are not necessary for single statement blocks
drivers/net/wireless/ath/ath10k/mac.c:200: braces {} are not necessary for single statement blocks

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k: indentation fixes

checkpatch found:

drivers/net/wireless/ath/ath10k/core.c:513: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/core.c:1266: code indent should use tabs where possible
drivers/net/wireless/ath/ath10k/core.c:1267: code indent should use tabs where possible
drivers/net/wireless/ath/ath10k/core.c:1268: code indent should use tabs where possible
drivers/net/wireless/ath/ath10k/core.c:1269: code indent should use tabs where possible
drivers/net/wireless/ath/ath10k/mac.c:4659: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/mac.c:6271: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/pci.c:2260: Alignment should match open parenthesis
drivers/net/wireless/ath/ath10k/wmi.c:3510: Alignment should match open parenthesis

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k: fix checkpatch warning about logical continuations

checkpatch found:

drivers/net/wireless/ath/ath9k/core.c:490: Logical continuations should be on the previous line

Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Merge ath-next from ath.git

Major changes in ath10k:

* add spectral scan support for 10.4 firmware
* add qca6164 support
* implement mesh support using firmware raw mode

mwifiex: fix mwifiex_rdeeprom_read()

There were several bugs here.

1)  The done label was in the wrong place so we didn't copy any
    information out when there was no command given.

2)  We were using PAGE_SIZE as the size of the buffer instead of
    "PAGE_SIZE - pos".

3)  snprintf() returns the number of characters that would have been
    printed if there were enough space.  If there was not enough space
    (and we had fixed the memory corruption bug #2) then it would result
    in an information leak when we do simple_read_from_buffer().  I've
    changed it to use scnprintf() instead.

I also removed the initialization at the start of the function, because
I thought it made the code a little more clear.

Fixes: 5e6e3a92b9a4 ('wireless: mwifiex: initial commit for Marvell mwifiex driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

airo: Implement netif_carrier_on/off

Add calls to netif_carrier_on and netif_carrier_off

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

airo: fix IW_AUTH_ALG_OPEN_SYSTEM

IW_AUTH_ALG_OPEN_SYSTEM is ambiguous in set_auth for WEP as
wpa_supplicant uses it for both no encryption and WEP open system.
Cache the last mode set (only of these two) and use it here.

This allows wpa_supplicant to work with unencrypted APs.

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ssb: make ssb_pcmcia_switch_core static

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ssb: drop declaration of non existing ssb_sdio_hardware_setup

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ssb: make ssb_sdio_switch_core static

It's used locally only.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ssb: unexport ssb_bus_pcibus_register

It isn't used anywhere out of ssb code and we don't (plan to) build
pcihost_wrapper.c as a separated module.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

bcma: add support for population subnodes also when build as module

of_default_bus_match_table was not exported earlier, so it could only
be accessed by code compiled into the kernel. A new function
of_platform_default_populate() was added which uses
of_default_bus_match_table and this function is also exported. This way
it is possible to create a bus with the content of
of_default_bus_match_table and we can remove the hacks from bcma.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: include linux/atomic.h

brcmfmac uses atomic_or() and other atomic_* functions, but does not
include linux/atomic.h. This file gets included by some other header
file so this normally does not cause problems.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Accept events when TDLS is used in combination with p2p.

TDLS events are mapped back to primary interface but when p2p is in
use then this fails because the check was incorrect by checking
bsscfg number. Which can be different when a p2p device has been
created.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Fix TDLS setup by properly handling p2p noif.

There is a workaround needed for p2p device setup which breaks tdls
functionality. This patch fixes that by properly signalling fweh that
p2p device setup is ongoing.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Add support for the BCM4365 and BCM4366 PCIE devices.

This patch adds support for the BCM4365 and BCM4366 11ac Wave2
PCIE devices.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Fix race condition bug when deleting p2p interface.

When p2p device interface gets deleted by deinitialising discovery
it will result in an event which removes the interface, but that is
also done by delete p2p interface code. This results in race
condition which sometimes results in lockup/crash. With this patch
the delete device interface will wait for the event (with timeout)
removing the possible race condition. Also on the stop device call
from cfg80211 the deinitialisation of the discovery device should
be avoided as it can result in a similar situation.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Add module parameter to disable features.

For debugging purpose it is very handy to be able to disable
features. It has happened a few times that new features turned
out not always being properly detected for all devices/firmwares.
Making it possible to disable the feature with a module parameter
will make testing/debugging easier.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Fix p2p bug for older firmwares.

Some devices with older firmwares are reporting new p2p device
interface with the wrong type. Accept this type to get p2p
working for these devices.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Only handle p2p_stop_device if vif is valid

In some situations it is possible that vif has been removed while
cfg80211 invokes the p2p_stop_device handler. This will result in
crash.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Deleting of p2p device is leaking memory.

When a p2p device gets deleted, the memory for the vif is not being
released. This is solved by reorganizing the cleanup path and
properly freeing the memory.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Workaround in change vif for wpa_supplicant support.

Different wpa_supplicants have different behavior and expectations
regarding the change_virtual_intf behavior. This patch implements
a workaround for the different versions and possible brcmfmac
configuration.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Make p2pon module param always available.

p2pon module param is currently under define BRCMDBG. Though it is
a needed option for older versions of the wpa_supplicant which do not
support the P2P_DEVICE interface.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Fix bug in flowring management.

The hash index stored in the flowrings is of type u16 but gets
stored in u8. This can result in incorrect indexing and possibly
result in crashes. This patch fixes the type.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Inform p2p module about p2pon through API

When the p2pon module param is used then p2p attach will initialize
p2p device iface in the firmware, but it is doing that by checking
data. It is cleaner to pass the p2pon information to p2p by API.
This information is also needed for other patch.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Only assign primary netdev to if2bss array.

The if2bss allows for translation of ifidx to bssidx which has a 1:n
relation. Therefor only the first (primary) netdev should be
assigned in this array. This fixes the p2pon=1 module param usage.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Fix set and get tx-power functions.

Implementation of tx-power (get and set) related functions are
still assuming mW interface. This is wrong as functions use dbm
(or mbm) nowadays. As a result a tx power configuration could
result in wrong power configuration.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Add support for the BCM4350 PCIE device.

This patch adds support fo the BRCM4350 2x2 11ac PCIE device.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Fix exception handling.

In some exception situations the ifp->vif was not properly assigned
which could result in crash.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: complete usb tx data with multi endpoints

This patch do the work to TX data with specific USB
endpoint. At the same time, update data_sent flag
according to multi port status. And is_port_ready
API is added for BSS interface to check if current
used usb data endpoint is available or not.

Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: add usb multi endpoints resync support

This patch add support for usb multi endpoints resync.
Once multi channel event is received from firmware,
update usb_mc_setp flag to block TX data until setup is over.
And available data endpoint will be attached to BSS interface.

Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: add usb tx data multi endpoints support

This patch add support for USB interface to TX data
with different endpoint. And previous TX information
are saved in new designed structure.

Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: add usb multi channel event process support

This patch add multi channel event process for USB multi tx data endpoints.
Driver receives firmware multi channel event only in case that new
connection is setup or interface is disconnect. Different BSS interface
need update used usb endpoint.

Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: move usb specific data_sent update to usb.c

This patch move data_sent flag update to usb.c file.
>From now all data_sent update cases only happened in specific file:
sdio.c, usb.c, pcie.c. Outside ot these files, it is only allowed
to check the value of data_ent.

Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: fix tx data_sent issue for usb interface

This patch fix missing tx data_sent flag update for usb interface.
Except USB interface, data_sent flag has been updated in specific
file such as sdio.c and pcie.c. So only USB interface type need check
when TX data completed.

Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: Suppress -ENOSR error for data traffic on USB

We have preallocated buffer pool for Tx data. During high
data traffic, all buffers are submitted to USB and driver needs
to wait until one of the buffers get available for next Tx
packet.

"data: -ENOSR is returned" errors is expected in this case. Let's
lower the priority of this message.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: correct paused tx data packet counter

This patch fixes observed issues while updating counter for
number of paused data packets in wmm queue when trying to
delete packet or delete station entry.

Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: avoid memsetting PCIe event buffer

Preallocated PCIe buffer is being reused for all PCIe interface
events. Physical address of the buffer is shared with firmware
so that it can perform DMA on it. As event length is specified
in the header, there should not be a problem if the buffer gets
overwritten.
We will save some cycles by avoiding memset everytime while
submitting the buffer to firmware.

Fixes: 2728cecdc7d6bf3d21(mwifiex: corrections in PCIe event skb)
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: fix NULL pointer dereference during hidden SSID scan

This NULL pointer dereference is observed during suspend resume
stress test. All pending commands are cancelled when system goes
into suspend state. There a corner case in which host may receive
response for last scan command after this and try to trigger extra
active scan for hidden SSIDs.

The issue is fixed by adding a NULL check to skip that extra scan.

Fixes: 2375fa2b36feaf34 (mwifiex: fix unable to connect hidden SSID..)
Cc: <stable@vger.kernel.org> [v4.2+]
Signed-off-by: Aniket Nagarnaik <aniketn@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: don't always include ht/vht info in tdls confirm frame

Current TDLS implementation always includes ht/vht information
in tdls setup confirm frame which causes teardown by legacy
peer station after TDLS handshake. We will inclue ht/vht
capabilities in tdls setup confirm frame only if peer station
supports it to fix this problem.

Signed-off-by: Aniket Nagarnaik <aniketn@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: NULL check for cfg80211_inform_bss()

cfg80211_inform_bss would return null in some cases, such as
memory allocation failure.

This patch adds sanity check for this case, to avoid possible
issues when above corner case is hit.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: fix driver init failure under memory pressure

64k Tx and Rx buffers are allocated during driver initialization
for SDIO level data aggregations. When host is under memory
pressure situation, kzalloc() request for 64k may fail.

We will try allocating 32k buffers and disable our rx single port
aggreagation feature in this situation.

If the allocation still fails, we will disable our sdio multport
aggregation feature as well. In this way, we will transmit and
receive packets one by one, thus reduce the demand for big
memory.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: minor corrections in multiport aggregation code

This patch includes below changes
1) Check if multiport aggregation feature flag while doing rx
length validation check.
2) Reset buffer size variables when buffers are freed.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: update amsdu tx packet time stamp

This patch fixes the issue of delay time in A-MSDU tx packet.
In generated new A-MSDU packet, the time stamp is initialized to zero.
Choose the time of first MSDU packet as aggregated packet's time.

Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: fix typo in del_virtual_intf() function

Interface counters should be incremented in add_virtual_intf()
and decremented in del_virtual_intf() function. This patch
corrects it.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

wlcore: align reg_ch_conf_last[] to 64bit

Align fields reg_ch_conf_last and reg_ch_conf_pending of
struct wl1271{} to 64bit.

Without this, on 64bit ARM, wlcore_set_pending_regdomain_ch() fails at
the point it calls set_bit(ch_bit_idx, (long*)wl->reg_ch_conf_pending);
Here is the error message while doing iw wlan0 scan or connect:

[   10.666857] wlcore: IRQ work
[   10.670046] wlcore: intr: 0x40 (fw_rx_counter = 1, drv_rx_counter = 0, tx_results_counter = 0)
[   10.678697] wlcore: WL1271_ACX_INTR_DATA
[   10.682810] Unhandled fault: alignment fault (0x96000021) at 0xffffffc037a817f4
[   10.690139] Internal error: : 96000021 [#1] PREEMPT SMP
[   10.695366] Modules linked in:
[   10.698437] CPU: 3 PID: 894 Comm: irq/60-wl18xx Tainted: G        W       4.2.0-rc6-linaro-hikey #2
[   10.707501] Hardware name: HiKey Development Board (DT)
[   10.712733] task: ffffffc03a9d1680 ti: ffffffc039e18000 task.ti: ffffffc039e18000
[   10.720239] PC is at set_bit+0x14/0x30
[   10.724002] LR is at wlcore_set_pending_regdomain_ch+0x40/0x4c

Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath9k: Add support for OCB mode

The patch adds support for "outside the context of a BSS"(OCB) mode
to ath9k driver and extends debugfs files by OCB ralated information.

This patch was tested on AR9380-AL1A cards.

Signed-off-by: Jan Kaisrlik <kaisrja1@fel.cvut.cz>
Cc: Michal Sojka <sojkam1@fel.cvut.cz>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

carl9170: fix bad rssi reading

Fix rssi calculation error which was introduced in otus to ar9170
porting.

Signed-off-by: Hiroaki KAWAI <hiroaki.kawai@gmail.com>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

net/wireless/wl18xx: Add missing MODULE_FIRMWARE

Fixes the output of 'modinfo --field firmware'.

Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath9k: enable hw manual peak calibration for QCA9561

This patch fix https://lists.openwrt.org/pipermail/openwrt-devel/
2015-August/034979.html. As the peak detect calibration is set
incorrectly.

Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: Make mwifiex_dbg a function, reduce object size

The mwifiex_dbg macro has two tests that could be consolidated
into a function reducing overall object size ~10KB (~4%).

So convert the macro into a function.

$ size drivers/net/wireless/mwifiex/built-in.o* (x86-64 defconfig)
   text    data     bss     dec     hex filename
 233102    8628    4809  246539   3c30b drivers/net/wireless/mwifiex/built-in.o.new
 243949    8628    4809  257386   3ed6a drivers/net/wireless/mwifiex/built-in.o.old

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Reset PCIE devices after recognition.

When PCIE type devices are being FW reloaded without being properly
reset then the device ends up in a locked state, requiring the
device to be completely powered down. This patch adds a reset
through watchdog at the moment the device (cores) has been
recognized. This will solve warm reboot issues.

Cc: Rafal Milecki <zajec5@gmail.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: introduce brcmf_net_detach() function

In case of error during brcmf_bus_start() the network interfaces were
freed using free_netdev(). However, the interfaces may have additional
memory allocated which is not freed. The netdev has destructor set to
brcmf_cfg80211_free_netdev() which frees the additional memory if
allocated and call free_netdev(). The brcmf_net_detach() either calls
brcmf_cfg80211_free_netdev() directly or uses unregister_netdev() when
struct net_device::reg_state indicates the netdev was registered.

Reported-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: change prototype for brcmf_fws_hdrpull()

Instead of passing ifidx and drvr just pass struct brcmf_if pointer
which holds both parameters.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: remove ifidx parameter from brcmf_fws_txstatus_suppressed()

The brcmf_fws_txstatus_suppressed() function prototype specifies an
ifidx parameter which is not used within the function implementation.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: add dedicated debug level for firmware console logging

Both PCIe and SDIO devices have the possibility to log the firmware
console output in kernel log. For PCIe it is logged when PCIE debug
level is enabled. For SDIO it is logged when user specifies a non-zero
console interval through debugfs. This patch tries to make it a
bit more consistent. The firmware console output is only logged when
FWCON debug level is enabled.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Pontus Fuchs <pontusf@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: add mapping for interface index to bsscfg index

Because the P2P Device interface in firmware uses the same interface
index as the primary interface we use the bsscfg index as index in the
struct brcmf_pub::iflist. However, in the data path we get the interface
index and not the bsscfg index. So we need a mapping of interface index
to bsscfg index, which can be determined upon handle adding the interface.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: pass struct brcmf_if instance in brcmf_txfinalize()

Most call sites of brcmf_txfinalize already have struct brcmf_if
instance so pass that to brcmf_txfinalize() as the function
needs it anyway.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: use brcmf_get_ifp() to map ifidx to struct brcmf_if instance

The knowledge on how to map the interface index to a struct brcmf_if
instance is in brcmf_get_ifp() so use that function when only the
interface index is known instead of accessing brcmf_pub::iflist
directly.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: correct detection of p2pdev interface event

The p2pdev interface is setup in firmware resulting in a interface
event. This event has role and no-if flag. When role is p2p client
and no-if flag is set it indicates that this is the p2pdev interface.
This info is used in handling the event and adding interface in the
driver.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: only call brcmf_cfg80211_detach() when attach was successful

In brcmf_bus_start() the function brcmf_cfg80211_attach() is called which
may fail. If this happens we should not call brcmf_cfg80211_detach() in
the failure path as it will result in NULL pointer dereference:

  brcmf_fweh_activate_events: Set event_msgs error (-5)
  brcmf_bus_start: failed: -5
  brcmf_sdio_firmware_callback: dongle is not responding
  BUG: unable to handle kernel NULL pointer dereference at 0000000000000068
  IP: [<ffffffff811e8f08>] kernfs_find_ns+0x18/0xd0
  PGD 0
  Oops: 0000 [#1] SMP
  Modules linked in: brcmfmac(O) brcmutil(O) cfg80211 auth_rpcgss
  CPU: 1 PID: 45 Comm: kworker/1:1 Tainted: G           O
  Hardware name: Dell Inc. Latitude E6410/07XJP9, BIOS A07 02/15/2011
  Workqueue: events request_firmware_work_func
  task: ffff880036c09ac0 ti: ffff880036dd4000 task.ti: ffff880036dd4000
  RIP: 0010:[<ffffffff811e8f08>]  [<ffffffff811e8f08>] kernfs_find_ns+0x18/0xd0
  RSP: 0018:ffff880036dd7a28  EFLAGS: 00010246
  RAX: ffff880036c09ac0 RBX: 0000000000000000 RCX: 000000007fffffff
  RDX: 0000000000000000 RSI: ffffffff816578b9 RDI: 0000000000000000
  RBP: ffff880036dd7a48 R08: 0000000000000000 R09: ffff880036c0b340
  R10: 00000000000002ec R11: ffff880036dd7b08 R12: ffffffff816578b9
  R13: 0000000000000000 R14: ffffffff816578b9 R15: ffff8800c6c87000
  FS:  0000000000000000(0000) GS:ffff88012bc40000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
  CR2: 0000000000000068 CR3: 0000000001a0b000 CR4: 00000000000006e0
  Stack:
   0000000000000000 ffffffff816578b9 0000000000000000 ffff8800c0d003c8
   ffff880036dd7a78 ffffffff811e8ff5 0000000ffffffff1 ffffffff81a9b060
   ffff8800c789f880 ffff8800c0d00000 ffff880036dd7a98 ffffffff811ebe0d
  Call Trace:
   [<ffffffff811e8ff5>] kernfs_find_and_get_ns+0x35/0x60
   [<ffffffff811ebe0d>] sysfs_unmerge_group+0x1d/0x60
   [<ffffffff81404ef2>] dpm_sysfs_remove+0x22/0x60
   [<ffffffff813f9db9>] device_del+0x49/0x240
   [<ffffffff815da768>] rfkill_unregister+0x58/0xc0
   [<ffffffffa06bd91b>] wiphy_unregister+0xab/0x2f0 [cfg80211]
   [<ffffffffa0742fe3>] brcmf_cfg80211_detach+0x23/0x50 [brcmfmac]
   [<ffffffffa074d986>] brcmf_detach+0x86/0xe0 [brcmfmac]
   [<ffffffffa0757de8>] brcmf_sdio_remove+0x48/0x120 [brcmfmac]
   [<ffffffffa0758ed9>] brcmf_sdiod_remove+0x29/0xd0 [brcmfmac]
   [<ffffffffa0759031>] brcmf_ops_sdio_remove+0xb1/0x110 [brcmfmac]
   [<ffffffffa001c267>] sdio_bus_remove+0x37/0x100 [mmc_core]
   [<ffffffff813fe026>] __device_release_driver+0x96/0x130
   [<ffffffff813fe0e3>] device_release_driver+0x23/0x30
   [<ffffffffa0754bc8>] brcmf_sdio_firmware_callback+0x2a8/0x5d0 [brcmfmac]
   [<ffffffffa074deaf>] brcmf_fw_request_nvram_done+0x15f/0x5e0 [brcmfmac]
   [<ffffffff8140142f>] ? devres_add+0x3f/0x50
   [<ffffffff810642b5>] ? usermodehelper_read_unlock+0x15/0x20
   [<ffffffff81400000>] ? platform_match+0x70/0xa0
   [<ffffffff8140f400>] request_firmware_work_func+0x30/0x60
   [<ffffffff8106828c>] process_one_work+0x14c/0x3d0
   [<ffffffff8106862a>] worker_thread+0x11a/0x450
   [<ffffffff81068510>] ? process_one_work+0x3d0/0x3d0
   [<ffffffff8106d692>] kthread+0xd2/0xf0
   [<ffffffff8106d5c0>] ? kthread_create_on_node+0x180/0x180
   [<ffffffff815ed35f>] ret_from_fork+0x3f/0x70
   [<ffffffff8106d5c0>] ? kthread_create_on_node+0x180/0x180
  Code: e9 40 fe ff ff 48 89 d8 eb 87 66 0f 1f 84 00 00 00 00 00 66 66 66 66
90 55 48 89 e5 41 56 49 89 f6 41 55 49 89 d5 31 d2 41 54 53 <0f> b7
47 68 48 8b 5f 48 66 c1 e8 05 83 e0 01 4d 85 ed 0f b6 c8
  RIP  [<ffffffff811e8f08>] kernfs_find_ns+0x18/0xd0
   RSP <ffff880036dd7a28>
  CR2: 0000000000000068
  ---[ end trace 87d6ec0d3fe46740 ]---

Reported-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: change parameters for brcmf_remove_interface()

Just pass the interface to be removed, ie. the struct brcmf_if instance.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: make brcmf_proto_hdrpull() return struct brcmf_if instance

Avoid spreading the ifidx in the driver, but have it return the
struct brcmf_if instance.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: consolidate ifp lookup in driver core

In rx path the firmware provide an interface index which is used to
map to a struct brcmf_if instance. However, this involves some trick
that is done in two places. This is changed by having driver core
providing brcmf_get_ifp() function.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath10k: fix MSI-X registering for qca99x0

In case of qca99x0 and MSI-X supported/enabled we
failed during interrupts registering with message:

ath10k_pci 0000:04:00.0: failed to request MSI-X ce irq 50: -22

Issue/fix was reproduced/tested using Dell Latitude E6430 laptop.

Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath10k: fix ldpc param for fixed rate

ldpc is not configured for fixed rates. This blocks auto rate vs fixed
rate performance comparison. Since firmware is considering ldpc vdev
param for fixed rate selection, it has to be configured to enable ldpc
for fixed rates.

Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath: use PRI value given by spec for fixed PRI

PRI value is used as divider when DFS detector analyzes candidate
radar pulses.
If PRI deviation is big from its origin PRI, DFS detector could miss
valid radar reports since HW often misses detecting radar pulses and
causes long interval value of pulses.

For instance from practical results, if runtime PRI is calculated as
1431 for fixed PRI value of 1428 and delta timestamp logs 15719,
the modular remainder will be 1409 and the delta between the remainder
and runtime PRI is 22 that is bigger than PRI tolerance which is 16.
As a result this radar report will be ignored even though it's valid.

By using spec defined PRI for fixed PRI, we can correct this error.

Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath: fix incorrect PPB on JAPAN chirp radar

The number of pulses per burst on Japan chirp radar is
between 1 and 3. The previous value, 20, is representing
number of bursts, but since current DFS detector is using
pulse detection other than bursts, use the pulse number
for correct radar detection.
Also using the highest number helps to avoid false detection.

Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Merge tag 'iwlwifi-next-for-kalle-2015-09-21' of git://git./linux/kernel/git/iwlwifi/iwlwifi-next

* some debugfs improvements;
* fix signedness in beacon statistics;
* deinline some functions to reduce size when device tracing is enabled;
* filter beacons out in AP mode when no stations are associated;
* deprecate firmwares version -12;
* fix a runtime PM vs. legacy suspend race;
* one-liner fix for a ToF bug;
* clean-ups in the rx code;
* small debugging improvement;
* fix WoWLAN with new firmware versions;

iwlwifi: mvm: add debug print for d0i3 exit indication

In order to verify d0i3 flow, add debug print to indicate
d0i3 exit was completed (right after tx was re-enabled),
along with the wakeup reasons.

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: mvm: configure wowlan configuration only if connected

Recent fw version added assert to make sure wowlan configuration
is configured only when a station is connected.

Change the driver behavior to pass this configuration only
if we indeed have ap station id (i.e. connected).

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: mvm: move RX API into its own file

The RX API is currently mixed up into the general fw-api.h
file, but we're going to need to extend it significantly in
the future, so move it to its own file.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: mvm: remove some unused defines from RX API

Remove some unused values from the RX API; these were used
with older firmware API that didn't have the RX energy API,
support for which was removed a long time ago.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: mvm: remove pointless cfg_phy_cnt length check

Since the driver can never configure the data here, this field
will always be reported as 0 by the firmware. Even if this was
not the case, however, it wouldn't matter since the extra data
would be added beyond the end of the phy_info structure we use
in the driver, so wouldn't harm anything in this code either.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: mvm: remove useless debug message from RX

This message is useless - it's in the good case that always
happens so enabling it doesn't really help. Just remove it.
There are other ways to debug this (e.g. tracing) so there's
no need to add a message in the bad case.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: mvm: make sure AP is operating for ToF

It's possible for an AP interface to be UP but not actually
operating (i.e. not beaconing etc.) - in this case it can't
actually do ToF, so check for it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: mvm: remove IWL_UCODE_TLV_API_STATS_V10 TLV flag

This flag is set in all supported firmwares.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>

iwlwifi: mvm: remove IWL_UCODE_TLV_API_ASYNC_DTM TLV flag

This flag is set in all supported firmwares.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>

iwlwifi: mvm: remove IWL_UCODE_TLV_API_SINGLE_SCAN_EBS TLV flag

All the supported firmwares have this flag set.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>

iwlwifi: mvm: remove IWL_UCODE_TLV_API_TX_POWER_DEV TLV flag

All the supported firmwares use the new API.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>

iwlwifi: mvm: remove IWL_UCODE_TLV_API_HDC_PHASE_0 TLV flag

All the supported firwmares support the new API.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

ath9k_htc: introduce support for different fw versions

Current kernel support only one fw name with theoretically only one
fw version located in “firmware/htc_[9271|7010].fw”. Which is ok so far we
have only one fw version (1.3). After we realised new fw 1.4, we faced
compatibility problem which was decided to solve by firmware name and
location:
- new firmware is located now in
firmware/ath9k_htc/htc_[9271|7010]-1.4.0.fw
- old version 1.3 should be on old place, so old kernel have no issues
with it.
- new kernels including this patch should be able to try different
supported (min..max) fw version.
- new kernel should be able to support old fw location too. At least for
now.

At same time this patch will add new module option which should allow user
to play with development  fw version without replacing stable one. If user
will set “ath9k_htc use_dev_fw=1” module will try to find
firmware/ath9k_htc/htc_[9271|7010]-1.dev.0.fw first and if it fails, use
stable version: for example...1.4.0.fw.

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

sch_dsmark: improve memory locality

Memory placement in sch_dsmark is silly : Better place mask/value
in the same cache line.

Also, we can embed small arrays in the first cache line and
remove a potential cache miss.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'bcmgenet-irq-coalesce'

Florian Fainelli says:

====================
net: bcmgenet: Interrupt coalescing

This patch series adds support for interrupt coalescing for GENET
adapters.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: bcmgenet: Implement RX coalescing control knobs

Add support for the ethtool rx-frames coalescing parameter which allows
defining the number of RX interrupts per frames received. The RDMA
engine supports a configurable timeout with a resolution of
approximately 8.192 us.

We can no longer enable the BDONE/PDONE interrupts as those would
fire for each packet/buffer received, which would defeat the MBDONE
interrupt purpose. The MBDONE interrupt is guaranteed to correspond to a
PDONE/BDONE interrupt when the threshold is set to 1.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: bcmgenet: Implement TX coalescing control knobs

Configuring the ethtool tx-frames property, which translates into N
packets before a TX interrupt is the simplest configuration scheme
because it requires no locking neither at the softare nor hardware
level, and is completely indepedent from the link speed. Since ethtool
does not allow per-tx queue coalescing parameters, we apply the same
setting to any transmit queue.

We can no longer enable the BDONE/PDONE interrupts as those would fire
for each packet/buffer received, which would defeat the MBDONE interrupt
purpose. The MBDONE interrupt is guaranteed to correspond to a
PDONE/BDONE interrupt when the threshold is set to 1, but offers
interrupt coalescing when the value is > 1.

Since the HW is configured to generate an interrupt when the ring
becomes emtpy, we have to deny any timeout/timer settings coming from
user-space to indicate we can only generate an interrupt very <N>
packets.

While we are at it, fix the DMA_INTR_THRESHOLD_MASK value which was off
by one bit (0xff vs. 0x1ff).

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

lan78xx: Remove not defined MAC_CR_GMII_EN_ bit from MAC_CR.

Remove not defined MAC_CR_GMII_EN_ bit from MAC_CR.

Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

lan78xx: Create lan78xx_get_mdix_status() and lan78xx_set_mdix_status() for MDIX control.

Create lan78xx_get_mdix_status() and lan78xx_set_mdix_status() for MDIX control.

Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

lan78xx: Remove phy defines in lan78xx.h and use defines in include/linux/microchipphy.h

Remove phy defines in lan78xx.h and use defines in include/linux/microchipphy.h.

Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

lan78xx: Update to use phylib instead of mii_if_info.

Update to use phylib instead of mii_if_info.

Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

lan78xx: Add PHYLIB and MICROCHIP_PHY as default config.

Add PHYLIB and MICROCHIP_PHY as default configuration for lan78xx.

Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

lan78xx: Check device ready bit (PMT_CTL_READY_) after reset the PHY

Check device ready bit (PMT_CTL_READY_) after reset the PHY.
Device may not be ready even if PHY_RST_ is cleared depends on configuration.

Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Initialize table in fib result

Sergey, Richard and Fabio reported an oops in ip_route_input_noref. e.g., from Richard:

[    0.877040] BUG: unable to handle kernel NULL pointer dereference at 0000000000000056
[    0.877597] IP: [<ffffffff8155b5e2>] ip_route_input_noref+0x1a2/0xb00
[    0.877597] PGD 3fa14067 PUD 3fa6e067 PMD 0
[    0.877597] Oops: 0000 [#1] SMP
[    0.877597] Modules linked in: virtio_net virtio_pci virtio_ring virtio
[    0.877597] CPU: 1 PID: 119 Comm: ifconfig Not tainted 4.2.0+ #1
[    0.877597] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[    0.877597] task: ffff88003fab0bc0 ti: ffff88003faa8000 task.ti: ffff88003faa8000
[    0.877597] RIP: 0010:[<ffffffff8155b5e2>]  [<ffffffff8155b5e2>] ip_route_input_noref+0x1a2/0xb00
[    0.877597] RSP: 0018:ffff88003ed03ba0  EFLAGS: 00010202
[    0.877597] RAX: 0000000000000046 RBX: 00000000ffffff8f RCX: 0000000000000020
[    0.877597] RDX: ffff88003fab50b8 RSI: 0000000000000200 RDI: ffffffff8152b4b8
[    0.877597] RBP: ffff88003ed03c50 R08: 0000000000000000 R09: 0000000000000000
[    0.877597] R10: 0000000000000000 R11: 0000000000000000 R12: ffff88003fab6f00
[    0.877597] R13: ffff88003fab5000 R14: 0000000000000000 R15: ffffffff81cb5600
[    0.877597] FS:  00007f6de5751700(0000) GS:ffff88003ed00000(0000) knlGS:0000000000000000
[    0.877597] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[    0.877597] CR2: 0000000000000056 CR3: 000000003fa6d000 CR4: 00000000000006e0
[    0.877597] Stack:
[    0.877597]  0000000000000000 0000000000000046 ffff88003fffa600 ffff88003ed03be0
[    0.877597]  ffff88003f9e2c00 697da8c0017da8c0 ffff880000000000 000000000007fd00
[    0.877597]  0000000000000000 0000000000000046 0000000000000000 0000000400000000
[    0.877597] Call Trace:
[    0.877597]  <IRQ>
[    0.877597]  [<ffffffff812bfa1f>] ? cpumask_next_and+0x2f/0x40
[    0.877597]  [<ffffffff8158e13c>] arp_process+0x39c/0x690
[    0.877597]  [<ffffffff8158e57e>] arp_rcv+0x13e/0x170
[    0.877597]  [<ffffffff8151feec>] __netif_receive_skb_core+0x60c/0xa00
[    0.877597]  [<ffffffff81515795>] ? __build_skb+0x25/0x100
[    0.877597]  [<ffffffff81515795>] ? __build_skb+0x25/0x100
[    0.877597]  [<ffffffff81521ff6>] __netif_receive_skb+0x16/0x70
[    0.877597]  [<ffffffff81522078>] netif_receive_skb_internal+0x28/0x90
[    0.877597]  [<ffffffff8152288f>] napi_gro_receive+0x7f/0xd0
[    0.877597]  [<ffffffffa0017906>] virtnet_receive+0x256/0x910 [virtio_net]
[    0.877597]  [<ffffffffa0017fd8>] virtnet_poll+0x18/0x80 [virtio_net]
[    0.877597]  [<ffffffff815234cd>] net_rx_action+0x1dd/0x2f0
[    0.877597]  [<ffffffff81053228>] __do_softirq+0x98/0x260
[    0.877597]  [<ffffffff8164969c>] do_softirq_own_stack+0x1c/0x30

The root cause is use of res.table uninitialized.

Thanks to Nikolay for noticing the uninitialized use amongst the maze of
gotos.

As Nikolay pointed out the second initialization is not required to fix
the oops, but rather to fix a related problem where a valid lookup should
be invalidated before creating the rth entry.

Fixes: b7503e0cdb5d ("net: Add FIB table id to rtable")
Reported-by: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Reported-by: Richard Alpe <richard.alpe@ericsson.com>
Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'bpf_avoid_clone'

Alexei Starovoitov says:

====================
bpf: performance improvements

v1->v2: dropped redundant iff_up check in patch 2

At plumbers we discussed different options on how to get rid of skb_clone
from bpf_clone_redirect(), the patch 2 implements the best option.
Patch 1 adds 'integrated exts' to cls_bpf to improve performance by
combining simple actions into bpf classifier.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

bpf: add bpf_redirect() helper

Existing bpf_clone_redirect() helper clones skb before redirecting
it to RX or TX of destination netdev.
Introduce bpf_redirect() helper that does that without cloning.

Benchmarked with two hosts using 10G ixgbe NICs.
One host is doing line rate pktgen.
Another host is configured as:
$ tc qdisc add dev $dev ingress
$ tc filter add dev $dev root pref 10 u32 match u32 0 0 flowid 1:2 \
   action bpf run object-file tcbpf1_kern.o section clone_redirect_xmit drop
so it receives the packet on $dev and immediately xmits it on $dev + 1
The section 'clone_redirect_xmit' in tcbpf1_kern.o file has the program
that does bpf_clone_redirect() and performance is 2.0 Mpps

$ tc filter add dev $dev root pref 10 u32 match u32 0 0 flowid 1:2 \
   action bpf run object-file tcbpf1_kern.o section redirect_xmit drop
which is using bpf_redirect() - 2.4 Mpps

and using cls_bpf with integrated actions as:
$ tc filter add dev $dev root pref 10 \
  bpf run object-file tcbpf1_kern.o section redirect_xmit integ_act classid 1
performance is 2.5 Mpps

To summarize:
u32+act_bpf using clone_redirect - 2.0 Mpps
u32+act_bpf using redirect - 2.4 Mpps
cls_bpf using redirect - 2.5 Mpps

For comparison linux bridge in this setup is doing 2.1 Mpps
and ixgbe rx + drop in ip_rcv - 7.8 Mpps

Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cls_bpf: introduce integrated actions

Often cls_bpf classifier is used with single action drop attached.
Optimize this use case and let cls_bpf return both classid and action.
For backwards compatibility reasons enable this feature under
TCA_BPF_FLAG_ACT_DIRECT flag.

Then more interesting programs like the following are easier to write:
int cls_bpf_prog(struct __sk_buff *skb)
{
  /* classify arp, ip, ipv6 into different traffic classes
   * and drop all other packets
   */
  switch (skb->protocol) {
  case htons(ETH_P_ARP):
    skb->tc_classid = 1;
    break;
  case htons(ETH_P_IP):
    skb->tc_classid = 2;
    break;
  case htons(ETH_P_IPV6):
    skb->tc_classid = 3;
    break;
  default:
    return TC_ACT_SHOT;
  }

  return TC_ACT_OK;
}

Joint work with Daniel Borkmann.

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>