ath9k: initialize the number of tx/rx streams correctly

AR9300 based hardware can 3x3 MCS rates, this should be set in the
HT capabilities.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: reduce the bits_per_symbol table size, support more streams

Instead of increasing bits_per_symbol for supporting more streams, keep
it single-stream only and multiply the values by the numer of streams.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: update the ath_max_4ms_framelen table

Include MCS0-31 and also add SGI for HT20. This makes it
possible to support more different rate combinations with
newer hardware.

Based on a patch by Selvam. T.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: update the MCS mask for MCS16 and above

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: clean up tx buffer handling

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: check for specific rx stuck conditions and recover from them

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: document IEEE80211_CONF_CHANGE_QOS

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: basic support for survey

This adds the first element of survey data, the noise floor figure.

Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: sample survey implementation for mac80211 & hwsim

This adds the survey function to both mac80211 itself and to mac80211_hwsim.
For the latter driver, we simply invent some noise level.A real driver which
cannot determine the real channel noise MUST NOT report any noise, especially
not a magically conjured one :-)

Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Group Key fix for VAPs

When I set up multiple VAPs with ath9k, I encountered an issue that
the traffic may be lost after a while.

The detailed phenomenon is
1. After a while the clients connected to one of these VAPs will get
into a state that no broadcast/multicast packets can be transfered
successfully while the unicast packets can be transfered normally.
2. Minutes latter the unitcast packets transfer will fail as well,
because the ARP entry is expired and it can't be freshed due to the
broadcast trouble.

It's caused by the group key overwritten and someone discussed this
issue in ath9k-devel maillist before, but haven't work out a fix yet.

I referred the method in madwifi, and made a patch for ath9k.
The method is to set the high bit of the sender(AP)'s address, and
associated that mac and the group key. It requires the hardware
supports multicast frame key search. It seems true for AR9160.

Not sure whether it's the correct way to fix this issue. But it seems
to work in my test. The patch is attached, feel free to revise it.

Signed-off-by: Daniel Yingqiang ma <yma.cool@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: rt2x00: rt2800usb: identify Allwin devices

Applied common sense, no info from the manufacturer:

(0x8516, 0x2070) is RT2070
(0x8516, 0x2770) is RT2770
(0x8516, 0x2870) is RT2870
[...]

Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: add missing newline

One HT debugging printk is missing a newline,
add it.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

orinoco: have sparse check endian issues

Orinoco should be endian clean, so enable the checking.

Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

orinoco: use cfg80211_find_ie

Instead of using a local function.

Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

orinoco: implement set_wiphy_params

... to set fragmentation and RTS thresholds. Also report RTS retry
settings during wiphy init.

Note that the existing semantics for enabling microwave robustness are
preserved on firmwares that have it.

Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Prevent running sta_cleanup timer unnecessarily

The sta_cleanup timer is used to periodically expire buffered frames from the
tx buf. The timer is executing periodically, regardless of the need for it.
This is wasting resources.

Fix this simply by not restarting the sta_cleanup timer if the tx buffer was
empty. Restart the timer when there is some more tx-traffic.

Cc: Janne Ylälehto <janne.ylalehto@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix stopping RX BA session from timer

Kalle reported that his system deadlocks since my
recent work in this area. The reason quickly became
apparent: we try to cancel_timer_sync() a timer
from within itself. Fix that by making the function
aware of the context it is called from.

Reported-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix typo in comments

The flag is called IEEE80211_TX_STAT_AMPDU rather than using the whole word
STATUS.

Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'wireless-next-2.6' of git://git./linux/kernel/git/iwlwifi/iwlwifi-2.6

iwlwifi: make scan antenna forcing more generic

Some future hardware will also require some antenna
overrides so make the current logic more generic;
right now it is semantically based on a workaround
for off-channel reception but the reasons for the
new antenna overrides will be different.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: remove monitor check

Off-channel reception is acceptable in monitor
mode, and checking for monitor mode this way is
not really correct anyway since it could be the
case while operating.

Now iwl_is_monitor_mode() is no longer used so
remove it completely.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: don't check monitor for scanning

Monitor mode operation need not (and probably should
not) affect scanning this way since real monitoring
can not properly happen while scanning anyway.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: rename TX_CMD_FLG_BT_DIS_MSK

The flag name is a little misleading, this
flag instructs the device to ignore bluetooth
messages for purposes of frame transmissions,
so rename the flag to TX_CMD_FLG_IGNORE_BT.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: make BT coex config a virtual method

Some future hardware will require a different command to
be sent for bluetooth coexist, so make this a virtual
method that can be changed on a per-device basis.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: more code clean up for agn devices

Since multiple new devices having similar uCode architecture and use same
registers address, remove more reference to 5000 series to eliminate the
confusion.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: sanity check for turn on aggregation tid

Perform sanity check for turn on aggregation tid. Also remove the
option for turn on all the aggregation tids at once since it is
deprecated function and not being used.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: PA type for 6000g2 series

For 6000g2 series of NICs, PA type is determined by uCode, driver do not
have to set the register for internal/external PA. It is a workaround
just for 6000 series NICs.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: add hw revision for 6000g2 NIC

Add hardware revision for 6000g2 series of NIC

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: remove redundant iwl_dump_lq_cmd()

This function is called twice in a row, remove the second one.

Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: add debugfs ops to iwlwifi

Seperate debugfs functions into iwlagn specific
debugfs file and Add debugfs ops to iwlwifi.

Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: remove duplicated debug functions

Use the show uCode statistics function for uCode debugging purposes only; it
is being duplicated in both debugfs and sysfs. remove the one from sysfs.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: bring up 6000 Series 2x2 AGN Gen2 adapters

This patch is to bring up 6000 Series 2x2 AGN Gen2 adapters.
Seperate various version numbers from 6000 Series definitions;
Add module firmware declaration for the new adapters;
Add additional device IDs and subsystem IDs;

Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: more generic eeprom defines

Some definition for eeprom apply to more than 5000 series device, change
the name to reflect it for easy reading.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: trigger scan synchronously

Scan requesting doesn't need to be asynchronous
since all code paths leading up to it can sleep.
Make the scan request a new util operation that
is hw-specific (to account for 3945 vs. agn)
and call it right in place.

This patch moves a lot of code into iwlagn as
it need not be in iwlcore.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: rename priv->scan to priv->scan_cmd

I keep checking what "priv->scan" is, so rename
it to "priv->scan_cmd" which more clearly tells
us what it is.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: remove scan_pass_start

Since we no longer do a multi-pass scan,
keeping track of how long each pass took
is pointless since there will only be one.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: remove next_scan_jiffies

This logic is just confusing, if anything it
belongs into mac80211. Also, even if we do
scan during the EAPOL handshake, that will
not cause any problems, just a short delay.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: correct atomic bitops usage

With atomic bitops, test_and_{set,clear}_bit
should be used instead of separate test_bit
and set_bit/clear_bit.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: remove scan_bands logic

Since mac80211 will now never request scanning
multiple bands, we can remove all the associated
logic and scan a single band only in each scan.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: set correct single/dual stream mask

Even the initial single/dual stream values will be overridden later when
issue link quality command; but still make sense not to use hard-code
value during initialization. Single/Dual stream mask are used to indicate the
best antenna for SISO/MIMO; different NIC has different tx antenna
configuration; so the parameter need to based on the valid tx antenna.

1x2 device: single tx antenna available, only SISO is valid
configuration, but still need to set up MIMO configuration, so set it up
with antenna A & B as default.
2x2 device: two tx antenna available, dual_stream will use both valid
antenna.

3x3 device: three tx antenna available, skip the first antenna and
choice the second and third antenna for dual_stream.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

Merge branch 'wireless-2.6' into wireless-next-2.6

Conflicts:
drivers/net/wireless/iwlwifi/iwl-6000.c

iwlwifi: correct 6000 EEPROM regulatory address

For 6000 series, the 2.4G HT40 band regulatory settings address in EEPROM
was off by 2.

Before the fix, you'll see this in dmesg:
[79535.788877] ieee80211 phy8: U iwl_mod_ht40_chan_info HT40 Ch. 7 [2.4GHz]
WIDE (0x61 0dBm): Ad-Hoc not supported
[79535.788880] ieee80211 phy8: U iwl_mod_ht40_chan_info HT40 Ch. 11 [2.4GHz]
WIDE (0x61 0dBm): Ad-Hoc not supported

And after the fix:
[91132.688706] ieee80211 phy14: U iwl_mod_ht40_chan_info HT40 Ch. 7 [2.4GHz]
IBSS ACTIVE WIDE (0x6f 0dBm): Ad-Hoc supported
[91132.688709] ieee80211 phy14: U iwl_mod_ht40_chan_info HT40 Ch. 11 [2.4GHz]
IBSS ACTIVE WIDE (0x6f 0dBm): Ad-Hoc supported

Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: fix scan races

When an internal scan is started, nothing protects the
is_internal_short_scan variable which can cause crashes,
cf. https://bugzilla.kernel.org/show_bug.cgi?id=15667.
Fix this by making the short scan request use the mutex
for locking, which requires making the request go to a
work struct so that it can sleep.

Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>

iwlwifi: initialize iwl_wimax_coex_cmd.flags

iwl_wimax_coex_cmd.flags can be really uninitialized, so fix
that.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: check scan request ie_len

In mac80211 we always check both scan_req->ie and scan_req->ie_len
against zero before usage, in iwlwifi we should do the same.

Remove not needed "left -= ie_len" while at it.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251: add support for dedicated IRQ line

wl1251 has WLAN_IRQ pin for generating interrupts to host processor,
which is mandatory in SPI mode and optional in SDIO mode (which can
use SDIO interrupts instead). However TI recommends using deditated
IRQ line for SDIO too.

Add support for using dedicated interrupt line with SDIO, but also leave
ability to switch to SDIO interrupts in case it's needed.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Reviewed-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Fix sparse endian warnings

This patch fixes a bunch of endian issues that
were exposed by sparse. It's a miracle that the driver
worked at all till now.

The Lord be praised.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Handle WMI timeouts properly

If a WMI command has timed out for some reason,
a late WMI response would end up updating the
response region of a new WMI request that has been
issued in the meantime.

Fix this race condition by dropping a WMI response
if a new WMI command has been issued.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Add dropped SKB count to debugfs

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Remove GPIO set on unload

There is no point in trying to set the LED pin
when the module is being unloaded. The target
would be reset anyway.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Use buffered register writes

This patch adds macros at certain places
which could be optimized for multiple register writes.

The performance of ath9k_htc improves considerably,
especially reducing the latency involved in a scan run.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Relocate Opmode initialization

Programming the opmode in the HW can be done
before the assoc_id and STA_ID registers are
setup. This helps ath9k_htc when multiple register
writes are used.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Add macros for multiple register writes

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Implement multiple register write support

This patch adds support for writing multiple registers
in a single USB command.

Specific calls from the HW code that performs multiple
register writes would be modified to make use of this
in subsequent patches.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath: Add buffered register write operations

This is required to implement delayed/buffered
register writes in ath9k_htc.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Cleanup beacon configuration

This patch cleans up beacon configuration,
removing a redundant interface type check
and updating beacon interval in the correct place.

Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwmc3200wifi: check sparse endianness annotations

Add -D__CHECK_ENDIAN__ to driver ccflags so that sparse will
always check endianness by default.

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwmc3200wifi: Fix sparse warnings

Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k/ath9k: Fix 64 bits TSF reads

According to tests, both TSF lower and upper registers kept counting, so
the higher part could have been updated after the lower part has been
read, as shown in the following log where the upper part is read first
and the lower part next.

tsf = {00000003-fffffffd}
tsf = {00000003-00000001}
tsf = {00000004-0000000b}

This patch corrects this by checking that the upper part has not been
changed while the lower part was read. It has been tested in an IBSS
network where artifical IBSS merges have been done in order to trigger
hundreds of rollover for the TSF lower part.

It follows the logic mentionned by Derek, with only 2 register reads
needed at each additional steps instead of 3 (the minimum number of
register reads is still 3).

Signed-off-by: Benoit Papillault <benoit.papillault@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: add the PCI ID for the first AR9300 device

The first AR9003 hardware family device supported is the
AR9300, which has the vendor:device id 168c:0030

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Abort rx if hw is not coming out of full sleep in reset

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Enable TXOK and TXERR interrupts for TX EDMA

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: add LDPC support

LDPC is enabled by the rate control if the its determined
that the target peer supports LDPC. We would have already
intersected the HT capabilities so if our peer supports
LDPC so do we.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: add LDPC support for AR9003

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: add LDPC control flag

LDPC will be enabled through the rate control algorithm
for each buffer the the tx_info flags.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Add Tx EDMA support

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Compute pointer checksum over the link descriptor

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Initialize and configure tx status for EDMA

Also add a function to clean up tx status ring.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Setup appropriate tx desc for regular dma and edma

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: set cwmin and cwmax to 0 for for AR9003 upon txq reset

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: enable CRC check of descriptors for AR9003

Enable CRC check on the descriptor fetched from host on AR9003
upon reseting the TX queue.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: add RXLP and RXHP to debugfs counters

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Fill descriptor abstrations for AR9003

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: move AR9002 mac ops to its own file

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Add function to configure tx status ring buffer

Also reset tx status ring suring chip reset.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Define abstraction for tx desc access

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Load SW filtered NF values and start NF cal during full reset for AR9003

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: skip WEP aggregation enable code for AR9003

The AR9002 hardware code enables aggregation for WEP but
mac80211 doesn't enable aggregation with WEP, and the AR9003
code family does not need this so skip it for now for AR9003
but leave the code and annotate we should eventually consider
how to remove this in consideration for the HAL unification
goals.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: skip asynch fifo enablement to AR9003

The asynch fifo code is specific to >= AR9287 so stuff it
into the AR9002 hardware family code and skip it for AR9003
cards.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Update ath9k_hw_set_dma for AR9300

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: add TX/RX gain register initialization for AR9003

This is done depending on what the EEPROM settings indicates.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: add the AR9300 SREV hw name print

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Configure Tx interrupt mitigation timer

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: move the RF claim stuff to AR9002 hardware family

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: move AR9280 PCI EEPROM fix to eeprom_def.c

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Fill get_isr() for AR9003

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: add OFDM spur mitigation for AR9003

We add this now as OFDM spur mitigation required accessing
the EEPROM for the AR9003 devices.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Implement AR9003 eeprom callbacks

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: restore mac address reading logic

Once upon a time the AR_EEPROM_MAC macro was added to let us
add a random attribute to the three 4-bytes of MAC addresses
entries we read from the EEPROM. This was good while a random
high-enough value was used which did not conflict with any
of the already existing enum eeprom_param values. With AR9003
support the enums overlap and it means we either increment
the random offset or just restore the reading logic to match
what the HAL has. I choose to do the later to synchronize
the logic on both code bases.

This should fix reading the MAC address from the EEPROM
on AR9003 hardware.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: rename eep_AR9287_ops to eep_ar9287_ops

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: complete AR9003 calibration

This goes with some new shiny TX IQ calibration that AR9003
hardware family supports.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: fill in the callbacks for calibration for AR9003

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: abstract loading noisefloor

This is the last call on calib.c which acceses PHY stuff,
with this change we calib.c is now generic between both
all supported hardware families.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: abstract the AR_PHY_AGC_CONTROL register access

This is so we can share routines which access this register
on calib.c

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Initialize interrupt mask for AR9003

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Abstract the routine which returns interrupt status

Also move interrupt related code to mac.c

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: move TX/RX gain INI stuff to its own hardware family code

The AR9003 TX/RX gain is currently initialized with the other
components, so for now AR9003 does not implment this callback,
after hardware bring up  we can test moving the TX/RX gain there
as well and if it works well move them to its own callback as
well.

Since all INI stuff is now moved out hw.c no longer needs to
include and touch any original INI headers/structs.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: move the cck channel 14 INI to the AR9002 hw code

This is specific to the AR9002 family only.

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: split the generic hardware code by hardware family

Move out the generic hardware family code out into their own
files, we have one for AR5008, AR9001, and AR9002 family (ar9002_hw.c)
and another file for the new AR9003 hardware family (ar9003_hw.c).

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: add the config_pci_powersave AR9003 callback

Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>