git.openwrt.org Git - openwrt/staging/blogic.git/log

devlink: Fix resource coverity errors

Fix resource coverity errors.

Fixes: d9f9b9a4d05f ("devlink: Add support for resource abstraction")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ipv4: don't allow setting net.ipv4.route.min_pmtu below 68

According to RFC 1191 sections 3 and 4, ICMP frag-needed messages
indicating an MTU below 68 should be rejected:

    A host MUST never reduce its estimate of the Path MTU below 68
    octets.

and (talking about ICMP frag-needed's Next-Hop MTU field):

    This field will never contain a value less than 68, since every
    router "must be able to forward a datagram of 68 octets without
    fragmentation".

Furthermore, by letting net.ipv4.route.min_pmtu be set to negative
values, we can end up with a very large PMTU when (-1) is cast into u32.

Let's also make ip_rt_min_pmtu a u32, since it's only ever compared to
unsigned ints.

Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth

Johan Hedberg says:

====================
pull request: bluetooth 2018-02-26

Here are a two Bluetooth driver fixes for the 4.16 kernel.

Please let me know if there are any issues pulling. Thanks.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

devlink: Compare to size_new in case of resource child validation

The current implementation checks the combined size of the children with
the 'size' of the parent. The correct behavior is to check the combined
size vs the pending change and to compare vs the 'size_new'.

Fixes: d9f9b9a4d05f ("devlink: Add support for resource abstraction")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Tested-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8152: fix tx packets accounting

r8152 driver handles TSO packets (limited to ~16KB) quite well,
but pretends each TSO logical packet is a single packet on the wire.

There is also some error since headers are accounted once, but
error rate is small enough that we do not care.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip_tunnel: Do not use mark in skb by default

This reverts commit 5c38bd1b82e1f76f9fa96c1e61c9897cabf1ce45.

skb->mark contains the mark the encapsulated traffic which
can result in incorrect routing decisions being made such
as routing loops if the route chosen is via tunnel itself.
The correct method should be to use tunnel->fwmark.

Signed-off-by: Thomas Winter <thomas.winter@alliedtelesis.co.nz>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bridge: Fix VLAN reference count problem

When a VLAN is added on a port, a reference is taken on the
corresponding master VLAN entry. If it does not already exist, then it
is created and a reference taken.

However, in the second case a reference is not really taken when
CONFIG_REFCOUNT_FULL is enabled as refcount_inc() is replaced by
refcount_inc_not_zero().

Fix this by using refcount_set() on a newly created master VLAN entry.

Fixes: 251277598596 ("net, bridge: convert net_bridge_vlan.refcnt from atomic_t to refcount_t")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DT: net: renesas,ravb: document R8A77980 bindings

Renesas R-Car V3H (R8A77980) SoC has the R-Car gen3 compatible EtherAVB
device, so document the SoC specific bindings.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

qrtr: add MODULE_ALIAS macro to smd

Added MODULE_ALIAS("rpmsg:IPCRTR") to ensure qrtr-smd and qrtr will load
when IPCRTR channel is detected.

Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

hdlc_ppp: carrier detect ok, don't turn off negotiation

Sometimes when physical lines have a just good noise to make the protocol
handshaking fail, but the carrier detect still good. Then after remove of
the noise, nobody will trigger this protocol to be start again to cause
the link to never come back. The fix is when the carrier is still on, not
terminate the protocol handshaking.

Signed-off-by: Denis Du <dudenis2000@yahoo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

tuntap: correctly add the missing XDP flush

We don't flush batched XDP packets through xdp_do_flush_map(), this
will cause packets stall at TX queue. Consider we don't do XDP on NAPI
poll(), the only possible fix is to call xdp_do_flush_map()
immediately after xdp_do_redirect().

Note, this in fact won't try to batch packets through devmap, we could
address in the future.

Reported-by: Christoffer Dall <christoffer.dall@linaro.org>
Fixes: 761876c857cb ("tap: XDP support")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tuntap: disable preemption during XDP processing

Except for tuntap, all other drivers' XDP was implemented at NAPI
poll() routine in a bh. This guarantees all XDP operation were done at
the same CPU which is required by e.g BFP_MAP_TYPE_PERCPU_ARRAY. But
for tuntap, we do it in process context and we try to protect XDP
processing by RCU reader lock. This is insufficient since
CONFIG_PREEMPT_RCU can preempt the RCU reader critical section which
breaks the assumption that all XDP were processed in the same CPU.

Fixing this by simply disabling preemption during XDP processing.

Fixes: 761876c857cb ("tap: XDP support")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Revert "tuntap: add missing xdp flush"

This reverts commit 762c330d670e3d4b795cf7a8d761866fdd1eef49. The
reason is we try to batch packets for devmap which causes calling
xdp_do_flush() in the process context. Simply disabling preemption
may not work since process may move among processors which lead
xdp_do_flush() to miss some flushes on some processors.

So simply revert the patch, a follow-up patch will add the xdp flush
correctly.

Reported-by: Christoffer Dall <christoffer.dall@linaro.org>
Fixes: 762c330d670e ("tuntap: add missing xdp flush")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: fix crash in build_skb Rx code path

Add check for build_skb enabled ring in ixgbe_dma_sync_frag().
In that case &skb_shinfo(skb)->frags[0] may not always be set which
can lead to a crash. Instead we derive the page offset from skb->data.

Fixes: 42073d91a214
("ixgbe: Have the CPU take ownership of the buffers sooner")
CC: stable <stable@vger.kernel.org>
Reported-by: Ambarish Soman <asoman@redhat.com>
Suggested-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ARM: orion5x: Revert commit 4904dbda41c8.

It is not valid for orion5x to use mac_pton().

First of all, the orion5x buffer is not NULL terminated. mac_pton()
has no business operating on non-NULL terminated buffers because
only the caller can know that this is valid and in what manner it
is ok to parse this NULL'less buffer.

Second of all, orion5x operates on an __iomem pointer, which cannot
be dereferenced using normal C pointer operations. Accesses to
such areas much be performed with the proper iomem accessors.

Fixes: 4904dbda41c8 ("ARM: orion5x: use mac_pton() helper")
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'l2tp-fix-API-races-discovered-by-syzbot'

James Chapman says:

====================
l2tp: fix API races discovered by syzbot

This patch series addresses several races with L2TP APIs discovered by
syzbot. There are no functional changes.

The set of patches 1-5 in combination fix the following syzbot reports.

19c09769f WARNING in debug_print_object
347bd5acd KASAN: use-after-free Read in inet_shutdown
6e6a5ec8d general protection fault in pppol2tp_connect
9df43faf0 KASAN: use-after-free Read in pppol2tp_connect

My first attempts to fix these issues were as net-next patches but
the series included other refactoring and cleanup work. I was asked to
separate out the bugfixes and redo for the net tree, which is what
these patches are.

The changes are:

1. Fix inet_shutdown races when L2TP tunnels and sessions close. (patches 1-2)
2. Fix races with tunnel and its socket. (patch 3)
3. Fix race in pppol2tp_release with session and its socket. (patch 4)
4. Fix tunnel lookup use-after-free. (patch 5)

All of the syzbot reproducers hit races in the tunnel and pppol2tp
session create and destroy paths. These tests create and destroy
pppol2tp tunnels and sessions rapidly using multiple threads,
provoking races in several tunnel/session create/destroy paths. The
key problem was that each tunnel/session socket could be destroyed
while its associated tunnel/session object still existed (patches 3,
4). Patch 5 addresses a problem with the way tunnels are removed from
the tunnel list. Patch 5 is tagged that it addresses all four syzbot
issues, though all 5 patches are needed.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

l2tp: fix tunnel lookup use-after-free race

l2tp_tunnel_get walks the tunnel list to find a matching tunnel
instance and if a match is found, its refcount is increased before
returning the tunnel pointer. But when tunnel objects are destroyed,
they are on the tunnel list after their refcount hits zero. Fix this
by moving the code that removes the tunnel from the tunnel list from
the tunnel socket destructor into in the l2tp_tunnel_delete path,
before the tunnel refcount is decremented.

refcount_t: increment on 0; use-after-free.
WARNING: CPU: 3 PID: 13507 at lib/refcount.c:153 refcount_inc+0x47/0x50
Modules linked in:
CPU: 3 PID: 13507 Comm: syzbot_6e6a5ec8 Not tainted 4.16.0-rc2+ #36
Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
RIP: 0010:refcount_inc+0x47/0x50
RSP: 0018:ffff8800136ffb20 EFLAGS: 00010286
RAX: dffffc0000000008 RBX: ffff880017068e68 RCX: ffffffff814d3333
RDX: 0000000000000000 RSI: ffff88001a59f6d8 RDI: ffff88001a59f6d8
RBP: ffff8800136ffb28 R08: 0000000000000000 R09: 0000000000000000
R10: ffff8800136ffab0 R11: 0000000000000000 R12: ffff880017068e50
R13: 0000000000000000 R14: ffff8800174da800 R15: 0000000000000004
FS: 00007f403ab1e700(0000) GS:ffff88001a580000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000205fafd2 CR3: 0000000016770000 CR4: 00000000000006e0
Call Trace:
l2tp_tunnel_get+0x2dd/0x4e0
pppol2tp_connect+0x428/0x13c0
? pppol2tp_session_create+0x170/0x170
? __might_fault+0x115/0x1d0
? lock_downgrade+0x860/0x860
? __might_fault+0xe5/0x1d0
? security_socket_connect+0x8e/0xc0
SYSC_connect+0x1b6/0x310
? SYSC_bind+0x280/0x280
? __do_page_fault+0x5d1/0xca0
? up_read+0x1f/0x40
? __do_page_fault+0x3c8/0xca0
SyS_connect+0x29/0x30
? SyS_accept+0x40/0x40
do_syscall_64+0x1e0/0x730
? trace_hardirqs_off_thunk+0x1a/0x1c
entry_SYSCALL_64_after_hwframe+0x42/0xb7
RIP: 0033:0x7f403a42f259
RSP: 002b:00007f403ab1dee8 EFLAGS: 00000296 ORIG_RAX: 000000000000002a
RAX: ffffffffffffffda RBX: 00000000205fafe4 RCX: 00007f403a42f259
RDX: 000000000000002e RSI: 00000000205fafd2 RDI: 0000000000000004
RBP: 00007f403ab1df20 R08: 00007f403ab1e700 R09: 0000000000000000
R10: 00007f403ab1e700 R11: 0000000000000296 R12: 0000000000000000
R13: 00007ffc81906cbf R14: 0000000000000000 R15: 00007f403ab2b040
Code: 3b ff 5b 5d c3 e8 ca 5f 3b ff 80 3d 49 8e 66 04 00 75 ea e8 bc 5f 3b ff 48 c7 c7 60 69 64 85 c6 05 34 8e 66 04 01 e8 59 49 15 ff <0f> 0b eb ce 0f 1f 44 00 00 55 48 89 e5 41 56 41 55 41 54 53 49

Fixes: f8ccac0e44934 ("l2tp: put tunnel socket release on a workqueue")
Reported-and-tested-by: syzbot+19c09769f14b48810113@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+347bd5acde002e353a36@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+6e6a5ec8de31a94cd015@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+9df43faf09bd400f2993@syzkaller.appspotmail.com
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

l2tp: fix race in pppol2tp_release with session object destroy

pppol2tp_release uses call_rcu to put the final ref on its socket. But
the session object doesn't hold a ref on the session socket so may be
freed while the pppol2tp_put_sk RCU callback is scheduled. Fix this by
having the session hold a ref on its socket until the session is
destroyed. It is this ref that is dropped via call_rcu.

Sessions are also deleted via l2tp_tunnel_closeall. This must now also put
the final ref via call_rcu. So move the call_rcu call site into
pppol2tp_session_close so that this happens in both destroy paths. A
common destroy path should really be implemented, perhaps with
l2tp_tunnel_closeall calling l2tp_session_delete like pppol2tp_release
does, but this will be looked at later.

ODEBUG: activate active (active state 1) object type: rcu_head hint:           (null)
WARNING: CPU: 3 PID: 13407 at lib/debugobjects.c:291 debug_print_object+0x166/0x220
Modules linked in:
CPU: 3 PID: 13407 Comm: syzbot_19c09769 Not tainted 4.16.0-rc2+ #38
Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
RIP: 0010:debug_print_object+0x166/0x220
RSP: 0018:ffff880013647a00 EFLAGS: 00010082
RAX: dffffc0000000008 RBX: 0000000000000003 RCX: ffffffff814d3333
RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffff88001a59f6d0
RBP: ffff880013647a40 R08: 0000000000000000 R09: 0000000000000001
R10: ffff8800136479a8 R11: 0000000000000000 R12: 0000000000000001
R13: ffffffff86161420 R14: ffffffff85648b60 R15: 0000000000000000
FS:  0000000000000000(0000) GS:ffff88001a580000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020e77000 CR3: 0000000006022000 CR4: 00000000000006e0
Call Trace:
debug_object_activate+0x38b/0x530
? debug_object_assert_init+0x3b0/0x3b0
? __mutex_unlock_slowpath+0x85/0x8b0
? pppol2tp_session_destruct+0x110/0x110
__call_rcu.constprop.66+0x39/0x890
? __call_rcu.constprop.66+0x39/0x890
call_rcu_sched+0x17/0x20
pppol2tp_release+0x2c7/0x440
? fcntl_setlk+0xca0/0xca0
? sock_alloc_file+0x340/0x340
sock_release+0x92/0x1e0
sock_close+0x1b/0x20
__fput+0x296/0x6e0
____fput+0x1a/0x20
task_work_run+0x127/0x1a0
do_exit+0x7f9/0x2ce0
? SYSC_connect+0x212/0x310
? mm_update_next_owner+0x690/0x690
? up_read+0x1f/0x40
? __do_page_fault+0x3c8/0xca0
do_group_exit+0x10d/0x330
? do_group_exit+0x330/0x330
SyS_exit_group+0x22/0x30
do_syscall_64+0x1e0/0x730
? trace_hardirqs_off_thunk+0x1a/0x1c
entry_SYSCALL_64_after_hwframe+0x42/0xb7
RIP: 0033:0x7f362e471259
RSP: 002b:00007ffe389abe08 EFLAGS: 00000202 ORIG_RAX: 00000000000000e7
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f362e471259
RDX: 00007f362e471259 RSI: 000000000000002e RDI: 0000000000000000
RBP: 00007ffe389abe30 R08: 0000000000000000 R09: 00007f362e944270
R10: 0000000000000000 R11: 0000000000000202 R12: 0000000000400b60
R13: 00007ffe389abf50 R14: 0000000000000000 R15: 0000000000000000
Code: 8d 3c dd a0 8f 64 85 48 89 fa 48 c1 ea 03 80 3c 02 00 75 7b 48 8b 14 dd a0 8f 64 85 4c 89 f6 48 c7 c7 20 85 64 85 e
8 2a 55 14 ff <0f> 0b 83 05 ad 2a 68 04 01 48 83 c4 18 5b 41 5c 41 5d 41 5e 41

Fixes: ee40fb2e1eb5b ("l2tp: protect sock pointer of struct pppol2tp_session with RCU")
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

l2tp: fix races with tunnel socket close

The tunnel socket tunnel->sock (struct sock) is accessed when
preparing a new ppp session on a tunnel at pppol2tp_session_init. If
the socket is closed by a thread while another is creating a new
session, the threads race. In pppol2tp_connect, the tunnel object may
be created if the pppol2tp socket is associated with the special
session_id 0 and the tunnel socket is looked up using the provided
fd. When handling this, pppol2tp_connect cannot sock_hold the tunnel
socket to prevent it being destroyed during pppol2tp_connect since
this may itself may race with the socket being destroyed. Doing
sockfd_lookup in pppol2tp_connect isn't sufficient to prevent
tunnel->sock going away either because a given tunnel socket fd may be
reused between calls to pppol2tp_connect. Instead, have
l2tp_tunnel_create sock_hold the tunnel socket before it does
sockfd_put. This ensures that the tunnel's socket is always extant
while the tunnel object exists. Hold a ref on the socket until the
tunnel is destroyed and ensure that all tunnel destroy paths go
through a common function (l2tp_tunnel_delete) since this will do the
final sock_put to release the tunnel socket.

Since the tunnel's socket is now guaranteed to exist if the tunnel
exists, we no longer need to use sockfd_lookup via l2tp_sock_to_tunnel
to derive the tunnel from the socket since this is always
sk_user_data.

Also, sessions no longer sock_hold the tunnel socket since sessions
already hold a tunnel ref and the tunnel sock will not be freed until
the tunnel is freed. Removing these sock_holds in
l2tp_session_register avoids a possible sock leak in the
pppol2tp_connect error path if l2tp_session_register succeeds but
attaching a ppp channel fails. The pppol2tp_connect error path could
have been fixed instead and have the sock ref dropped when the session
is freed, but doing a sock_put of the tunnel socket when the session
is freed would require a new session_free callback. It is simpler to
just remove the sock_hold of the tunnel socket in
l2tp_session_register, now that the tunnel socket lifetime is
guaranteed.

Finally, some init code in l2tp_tunnel_create is reordered to ensure
that the new tunnel object's refcount is set and the tunnel socket ref
is taken before the tunnel socket destructor callbacks are set.

kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
Modules linked in:
CPU: 0 PID: 4360 Comm: syzbot_19c09769 Not tainted 4.16.0-rc2+ #34
Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
RIP: 0010:pppol2tp_session_init+0x1d6/0x500
RSP: 0018:ffff88001377fb40 EFLAGS: 00010212
RAX: dffffc0000000000 RBX: ffff88001636a940 RCX: ffffffff84836c1d
RDX: 0000000000000045 RSI: 0000000055976744 RDI: 0000000000000228
RBP: ffff88001377fb60 R08: ffffffff84836bc8 R09: 0000000000000002
R10: ffff88001377fab8 R11: 0000000000000001 R12: 0000000000000000
R13: ffff88001636aac8 R14: ffff8800160f81c0 R15: 1ffff100026eff76
FS: 00007ffb3ea66700(0000) GS:ffff88001a400000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020e77000 CR3: 0000000016261000 CR4: 00000000000006f0
Call Trace:
pppol2tp_connect+0xd18/0x13c0
? pppol2tp_session_create+0x170/0x170
? __might_fault+0x115/0x1d0
? lock_downgrade+0x860/0x860
? __might_fault+0xe5/0x1d0
? security_socket_connect+0x8e/0xc0
SYSC_connect+0x1b6/0x310
? SYSC_bind+0x280/0x280
? __do_page_fault+0x5d1/0xca0
? up_read+0x1f/0x40
? __do_page_fault+0x3c8/0xca0
SyS_connect+0x29/0x30
? SyS_accept+0x40/0x40
do_syscall_64+0x1e0/0x730
? trace_hardirqs_off_thunk+0x1a/0x1c
entry_SYSCALL_64_after_hwframe+0x42/0xb7
RIP: 0033:0x7ffb3e376259
RSP: 002b:00007ffeda4f6508 EFLAGS: 00000202 ORIG_RAX: 000000000000002a
RAX: ffffffffffffffda RBX: 0000000020e77012 RCX: 00007ffb3e376259
RDX: 000000000000002e RSI: 0000000020e77000 RDI: 0000000000000004
RBP: 00007ffeda4f6540 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000202 R12: 0000000000400b60
R13: 00007ffeda4f6660 R14: 0000000000000000 R15: 0000000000000000
Code: 80 3d b0 ff 06 02 00 0f 84 07 02 00 00 e8 13 d6 db fc 49 8d bc 24 28 02 00 00 48 b8 00 00 00 00 00 fc ff df 48 89 f
a 48 c1 ea 03 <80> 3c 02 00 0f 85 ed 02 00 00 4d 8b a4 24 28 02 00 00 e8 13 16

Fixes: 80d84ef3ff1dd ("l2tp: prevent l2tp_tunnel_delete racing with userspace close")
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

l2tp: don't use inet_shutdown on ppp session destroy

Previously, if a ppp session was closed, we called inet_shutdown to mark
the socket as unconnected such that userspace would get errors and
then close the socket. This could race with userspace closing the
socket. Instead, leave userspace to close the socket in its own time
(our session will be detached anyway).

BUG: KASAN: use-after-free in inet_shutdown+0x5d/0x1c0
Read of size 4 at addr ffff880010ea3ac0 by task syzbot_347bd5ac/8296

CPU: 3 PID: 8296 Comm: syzbot_347bd5ac Not tainted 4.16.0-rc1+ #91
Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
Call Trace:
dump_stack+0x101/0x157
? inet_shutdown+0x5d/0x1c0
print_address_description+0x78/0x260
? inet_shutdown+0x5d/0x1c0
kasan_report+0x240/0x360
__asan_load4+0x78/0x80
inet_shutdown+0x5d/0x1c0
? pppol2tp_show+0x80/0x80
pppol2tp_session_close+0x68/0xb0
l2tp_tunnel_closeall+0x199/0x210
? udp_v6_flush_pending_frames+0x90/0x90
l2tp_udp_encap_destroy+0x6b/0xc0
? l2tp_tunnel_del_work+0x2e0/0x2e0
udpv6_destroy_sock+0x8c/0x90
sk_common_release+0x47/0x190
udp_lib_close+0x15/0x20
inet_release+0x85/0xd0
inet6_release+0x43/0x60
sock_release+0x53/0x100
? sock_alloc_file+0x260/0x260
sock_close+0x1b/0x20
__fput+0x19f/0x380
____fput+0x1a/0x20
task_work_run+0xd2/0x110
exit_to_usermode_loop+0x18d/0x190
do_syscall_64+0x389/0x3b0
entry_SYSCALL_64_after_hwframe+0x26/0x9b
RIP: 0033:0x7fe240a45259
RSP: 002b:00007fe241132df8 EFLAGS: 00000297 ORIG_RAX: 0000000000000003
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 00007fe240a45259
RDX: 00007fe240a45259 RSI: 0000000000000000 RDI: 00000000000000a5
RBP: 00007fe241132e20 R08: 00007fe241133700 R09: 0000000000000000
R10: 00007fe241133700 R11: 0000000000000297 R12: 0000000000000000
R13: 00007ffc49aff84f R14: 0000000000000000 R15: 00007fe241141040

Allocated by task 8331:
save_stack+0x43/0xd0
kasan_kmalloc+0xad/0xe0
kasan_slab_alloc+0x12/0x20
kmem_cache_alloc+0x144/0x3e0
sock_alloc_inode+0x22/0x130
alloc_inode+0x3d/0xf0
new_inode_pseudo+0x1c/0x90
sock_alloc+0x30/0x110
__sock_create+0xaa/0x4c0
SyS_socket+0xbe/0x130
do_syscall_64+0x128/0x3b0
entry_SYSCALL_64_after_hwframe+0x26/0x9b

Freed by task 8314:
save_stack+0x43/0xd0
__kasan_slab_free+0x11a/0x170
kasan_slab_free+0xe/0x10
kmem_cache_free+0x88/0x2b0
sock_destroy_inode+0x49/0x50
destroy_inode+0x77/0xb0
evict+0x285/0x340
iput+0x429/0x530
dentry_unlink_inode+0x28c/0x2c0
__dentry_kill+0x1e3/0x2f0
dput.part.21+0x500/0x560
dput+0x24/0x30
__fput+0x2aa/0x380
____fput+0x1a/0x20
task_work_run+0xd2/0x110
exit_to_usermode_loop+0x18d/0x190
do_syscall_64+0x389/0x3b0
entry_SYSCALL_64_after_hwframe+0x26/0x9b

Fixes: fd558d186df2c ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

l2tp: don't use inet_shutdown on tunnel destroy

Previously, if a tunnel was closed, we called inet_shutdown to mark
the socket as unconnected such that userspace would get errors and
then close the socket. This could race with userspace closing the
socket. Instead, leave userspace to close the socket in its own time
(our tunnel will be detached anyway).

BUG: unable to handle kernel NULL pointer dereference at 00000000000000a0
IP: __lock_acquire+0x263/0x1630
PGD 0 P4D 0
Oops: 0000 [#1] SMP KASAN
Modules linked in:
CPU: 2 PID: 42 Comm: kworker/u8:2 Not tainted 4.15.0-rc7+ #129
Workqueue: l2tp l2tp_tunnel_del_work
RIP: 0010:__lock_acquire+0x263/0x1630
RSP: 0018:ffff88001a37fc70 EFLAGS: 00010002
RAX: 0000000000000001 RBX: 0000000000000088 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffff88001a37fd18 R08: 0000000000000001 R09: 0000000000000000
R10: 0000000000000000 R11: 00000000000076fd R12: 00000000000000a0
R13: ffff88001a3722c0 R14: 0000000000000001 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff88001ad00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000000000a0 CR3: 000000001730b000 CR4: 00000000000006e0
Call Trace:
? __lock_acquire+0xc77/0x1630
? console_trylock+0x11/0xa0
lock_acquire+0x117/0x230
? lock_sock_nested+0x3a/0xa0
_raw_spin_lock_bh+0x3a/0x50
? lock_sock_nested+0x3a/0xa0
lock_sock_nested+0x3a/0xa0
inet_shutdown+0x33/0xf0
l2tp_tunnel_del_work+0x60/0xef
process_one_work+0x1ea/0x5f0
? process_one_work+0x162/0x5f0
worker_thread+0x48/0x3e0
? trace_hardirqs_on+0xd/0x10
kthread+0x108/0x140
? process_one_work+0x5f0/0x5f0
? kthread_stop+0x2a0/0x2a0
ret_from_fork+0x24/0x30
Code: 00 41 81 ff ff 1f 00 00 0f 87 7a 13 00 00 45 85 f6 49 8b 85
68 08 00 00 0f 84 ae 03 00 00 c7 44 24 18 00 00 00 00 e9 f0 00 00 00 <49> 81 3c
24 80 93 3f 83 b8 00 00 00 00 44 0f 44 c0 83 fe 01 0f
RIP: __lock_acquire+0x263/0x1630 RSP: ffff88001a37fc70
CR2: 00000000000000a0

Fixes: 309795f4bec2d ("l2tp: Add netlink control API for L2TP")
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bluetooth: hci_bcm: Make shutdown and device wake GPIO optional

According to the devicetree binding the shutdown and device wake
GPIOs are optional. Since commit 3e81a4ca51a1 ("Bluetooth: hci_bcm:
Mandate presence of shutdown and device wake GPIO") this driver
won't probe anymore on Raspberry Pi 3 and Zero W (no device wake GPIO
connected). So fix this regression by reverting this commit partially.

Fixes: 3e81a4ca51a1 ("Bluetooth: hci_bcm: Mandate presence of shutdown and device wake GPIO")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Bluetooth: btusb: Use DMI matching for QCA reset_resume quirking

Commit 61f5acea8737 ("Bluetooth: btusb: Restore QCA Rome suspend/resume fix
with a "rewritten" version") applied the USB_QUIRK_RESET_RESUME to all QCA
USB Bluetooth modules. But it turns out that the resume problems are not
caused by the QCA Rome chipset, on most platforms it resumes fine. The
resume problems are actually a platform problem (likely the platform
cutting all power when suspended).

The USB_QUIRK_RESET_RESUME quirk also disables runtime suspend, so by
matching on usb-ids, we're causing all boards with these chips to use extra
power, to fix resume problems which only happen on some boards.

This commit fixes this by applying the quirk based on DMI matching instead
of on usb-ids, so that we match the platform and not the chipset.

Here is the /sys/kernel/debug/usb/devices for the Bluetooth module:

T:  Bus=01 Lev=01 Prnt=01 Port=07 Cnt=04 Dev#=  5 Spd=12   MxCh= 0
D:  Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=e300 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836
Fixes: 61f5acea8737 ("Bluetooth: btusb: Restore QCA Rome suspend/resume..")
Cc: stable@vger.kernel.org
Cc: Brian Norris <briannorris@chromium.org>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reported-and-tested-by: Kevin Fenzi <kevin@scrye.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Merge git://git./linux/kernel/git/davem/net

Pull networking fixes from David Miller:

1) Fix TTL offset calculation in mac80211 mesh code, from Peter Oh.

2) Fix races with procfs in ipt_CLUSTERIP, from Cong Wang.

3) Memory leak fix in lpm_trie BPF map code, from Yonghong Song.

4) Need to use GFP_ATOMIC in BPF cpumap allocations, from Jason Wang.

5) Fix potential deadlocks in netfilter getsockopt() code paths, from
    Paolo Abeni.

6) Netfilter stackpointer size checks really are needed to validate
    user input, from Florian Westphal.

7) Missing timer init in x_tables, from Paolo Abeni.

8) Don't use WQ_MEM_RECLAIM in mac80211 hwsim, from Johannes Berg.

9) When an ibmvnic device is brought down then back up again, it can be
    sent queue entries from a previous session, handle this properly
    instead of crashing. From Thomas Falcon.

10) Fix TCP checksum on LRO buffers in mlx5e, from Gal Pressman.

11) When we are dumping filters in cls_api, the output SKB is empty, and
    the filter we are dumping is too large for the space in the SKB, we
    should return -EMSGSIZE like other netlink dump operations do.
    Otherwise userland has no signal that is needs to increase the size
    of its read buffer. From Roman Kapl.

12) Several XDP fixes for virtio_net, from Jesper Dangaard Brouer.

13) Module refcount leak in netlink when a dump start fails, from Jason
    Donenfeld.

14) Handle sub-optimal GSO sizes better in TCP BBR congestion control,
    from Eric Dumazet.

15) Releasing bpf per-cpu arraymaps can take a long time, add a
    condtional scheduling point. From Eric Dumazet.

16) Implement retpolines for tail calls in x64 and arm64 bpf JITs. From
    Daniel Borkmann.

17) Fix page leak in gianfar driver, from Andy Spencer.

18) Missed clearing of estimator scratch buffer, from Eric Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
  net_sched: gen_estimator: fix broken estimators based on percpu stats
  gianfar: simplify FCS handling and fix memory leak
  ipv6 sit: work around bogus gcc-8 -Wrestrict warning
  macvlan: fix use-after-free in macvlan_common_newlink()
  bpf, arm64: fix out of bounds access in tail call
  bpf, x64: implement retpoline for tail call
  rxrpc: Fix send in rxrpc_send_data_packet()
  net: aquantia: Fix error handling in aq_pci_probe()
  bpf: fix rcu lockdep warning for lpm_trie map_free callback
  bpf: add schedule points in percpu arrays management
  regulatory: add NUL to request alpha2
  ibmvnic: Fix early release of login buffer
  net/smc9194: Remove bogus CONFIG_MAC reference
  net: ipv4: Set addr_type in hash_keys for forwarded case
  tcp_bbr: better deal with suboptimal GSO
  smsc75xx: fix smsc75xx_set_features()
  netlink: put module reference if dump start fails
  selftests/bpf/test_maps: exit child process without error in ENOMEM case
  selftests/bpf: update gitignore with test_libbpf_open
  selftests/bpf: tcpbpf_kern: use in6_* macros from glibc
  ..

Merge branch 'fixes-v4.16-rc3' of git://git./linux/kernel/git/jmorris/linux-security

Pull security subsystem fixes from James Morris:

- keys fixes via David Howells:
      "A collection of fixes for Linux keyrings, mostly thanks to Eric
       Biggers:

        - Fix some PKCS#7 verification issues.

        - Fix handling of unsupported crypto in X.509.

        - Fix too-large allocation in big_key"

- Seccomp updates via Kees Cook:
      "These are fixes for the get_metadata interface that landed during
       -rc1. While the new selftest is strictly not a bug fix, I think
       it's in the same spirit of avoiding bugs"

- an IMA build fix from Randy Dunlap

* 'fixes-v4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  integrity/security: fix digsig.c build error with header file
  KEYS: Use individual pages in big_key for crypto buffers
  X.509: fix NULL dereference when restricting key with unsupported_sig
  X.509: fix BUG_ON() when hash algorithm is unsupported
  PKCS#7: fix direct verification of SignerInfo signature
  PKCS#7: fix certificate blacklisting
  PKCS#7: fix certificate chain verification
  seccomp: add a selftest for get_metadata
  ptrace, seccomp: tweak get_metadata behavior slightly
  seccomp, ptrace: switch get_metadata types to arch independent

Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux

Pull arm64 fixes from Catalin Marinas:
"arm64 and perf fixes:

   - build error when accessing MPIDR_HWID_BITMASK from .S

   - fix CTR_EL0 field definitions

   - remove/disable some kernel messages on user faults (unhandled
     signals, unimplemented syscalls)

   - fix kernel page fault in unwind_frame() with function graph tracing

   - fix perf sleeping while atomic errors when booting with ACPI"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: fix unwind_frame() for filtered out fn for function graph tracing
  arm64: Enforce BBM for huge IO/VMAP mappings
  arm64: perf: correct PMUVer probing
  arm_pmu: acpi: request IRQs up-front
  arm_pmu: note IRQs and PMUs per-cpu
  arm_pmu: explicitly enable/disable SPIs at hotplug
  arm_pmu: acpi: check for mismatched PPIs
  arm_pmu: add armpmu_alloc_atomic()
  arm_pmu: fold platform helpers into platform code
  arm_pmu: kill arm_pmu_platdata
  ARM: ux500: remove PMU IRQ bouncer
  arm64: __show_regs: Only resolve kernel symbols when running at EL1
  arm64: Remove unimplemented syscall log message
  arm64: Disable unhandled signal log messages by default
  arm64: cpufeature: Fix CTR_EL0 field definitions
  arm64: uaccess: Formalise types for access_ok()
  arm64: Fix compilation error while accessing MPIDR_HWID_BITMASK from .S files

Merge tag 'mips_fixes_4.16_3' of git://git./linux/kernel/git/jhogan/mips

Pull MIPS fix from James Hogan:
"A single MIPS fix for mismatching struct compat_flock, resulting in
bus errors starting Firefox on Debian 8 since 4.13"

* tag 'mips_fixes_4.16_3' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips:
MIPS: Drop spurious __unused in struct compat_flock

Merge branch 'for-linus' of git://git./linux/kernel/git/pmladek/printk

Pull printk fixlet from Petr Mladek:
"People expect to see the real pointer value for %px.

  Let's substitute '(null)' only for the other %p? format modifiers that
  need to deference the pointer"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk:
  vsprintf: avoid misleading "(null)" for %px

Merge branch 'i2c/for-current' of git://git./linux/kernel/git/wsa/linux

Pull i2c fixes from Wolfram Sang:
"Two bugfixes, one v4.16 regression fix, and two documentation fixes"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: designware: Consider SCL GPIO optional
  i2c: busses: i2c-sirf: Fix spelling: "formular" -> "formula".
  i2c: bcm2835: Set up the rising/falling edge delays
  i2c: i801: Add missing documentation entries for Braswell and Kaby Lake
  i2c: designware: must wait for enable

Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi

Pull SCSI fixes from James Bottomley:
"These are mostly fixes for problems with merge window code.

  In addition we have one doc update (alua) and two dead code removals
  (aiclib and octogon) a spurious assignment removal (csiostor) and a
  performance improvement for storvsc involving better interrupt
  spreading and increasing the command per lun handling"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: qla4xxx: skip error recovery in case of register disconnect.
  scsi: aacraid: fix shutdown crash when init fails
  scsi: qedi: Cleanup local str variable
  scsi: qedi: Fix truncation of CHAP name and secret
  scsi: qla2xxx: Fix incorrect handle for abort IOCB
  scsi: qla2xxx: Fix double free bug after firmware timeout
  scsi: storvsc: Increase cmd_per_lun for higher speed devices
  scsi: qla2xxx: Fix a locking imbalance in qlt_24xx_handle_els()
  scsi: scsi_dh: Document alua_rtpg_queue() arguments
  scsi: Remove Makefile entry for oktagon files
  scsi: aic7xxx: remove aiclib.c
  scsi: qla2xxx: Avoid triggering undefined behavior in qla2x00_mbx_completion()
  scsi: mptfusion: Add bounds check in mptctl_hp_targetinfo()
  scsi: sym53c8xx_2: iterator underflow in sym_getsync()
  scsi: bnx2fc: Fix check in SCSI completion handler for timed out request
  scsi: csiostor: remove redundant assignment to pointer 'ln'
  scsi: ufs: Enable quirk to ignore sending WRITE_SAME command
  scsi: ibmvfc: fix misdefined reserved field in ibmvfc_fcp_rsp_info
  scsi: qla2xxx: Fix memory corruption during hba reset test
  scsi: mpt3sas: fix an out of bound write

Merge tag 'drm-fixes-for-v4.16-rc3' of git://people.freedesktop.org/~airlied/linux

Pull drm fixes from Dave Airlie:
"A bunch of fixes for rc3:

  Exynos:
   - fixes for using monotonic timestamps
   - register definitions
   - removal of unused file

  ipu-v3L
   - minor changes
   - make some register arrays const+static
   - fix some leaks

  meson:
   - fix for vsync

  atomic:
   - fix for memory leak

  EDID parser:
   - add quirks for some more non-desktop devices
   - 6-bit panel fix.

  drm_mm:
   - fix a bug in the core drm mm hole handling

  cirrus:
   - fix lut loading regression

  Lastly there is a deadlock fix around runtime suspend for secondary
  GPUs.

  There was a deadlock between one thread trying to wait for a workqueue
  job to finish in the runtime suspend path, and the workqueue job it
  was waiting for in turn waiting for a runtime_get_sync to return.

  The fixes avoids it by not doing the runtime sync in the workqueue as
  then we always wait for all those tasks to complete before we runtime
  suspend"

* tag 'drm-fixes-for-v4.16-rc3' of git://people.freedesktop.org/~airlied/linux: (25 commits)
  drm/tve200: fix kernel-doc documentation comment include
  drm/edid: quirk Sony PlayStation VR headset as non-desktop
  drm/edid: quirk Windows Mixed Reality headsets as non-desktop
  drm/edid: quirk Oculus Rift headsets as non-desktop
  drm/meson: fix vsync buffer update
  drm: Handle unexpected holes in color-eviction
  drm: exynos: Use proper macro definition for HDMI_I2S_PIN_SEL_1
  drm/exynos: remove exynos_drm_rotator.h
  drm/exynos: g2d: Delete an error message for a failed memory allocation in two functions
  drm/exynos: fix comparison to bitshift when dealing with a mask
  drm/exynos: g2d: use monotonic timestamps
  drm/edid: Add 6 bpc quirk for CPT panel in Asus UX303LA
  gpu: ipu-csi: add 10/12-bit grayscale support to mbus_code_to_bus_cfg
  gpu: ipu-cpmem: add 16-bit grayscale support to ipu_cpmem_set_image
  gpu: ipu-v3: prg: fix device node leak in ipu_prg_lookup_by_phandle
  gpu: ipu-v3: pre: fix device node leak in ipu_pre_lookup_by_phandle
  drm/amdgpu: Fix deadlock on runtime suspend
  drm/radeon: Fix deadlock on runtime suspend
  drm/nouveau: Fix deadlock on runtime suspend
  drm: Allow determining if current task is output poll worker
  ...

net_sched: gen_estimator: fix broken estimators based on percpu stats

pfifo_fast got percpu stats lately, uncovering a bug I introduced last
year in linux-4.10.

I missed the fact that we have to clear our temporary storage
before calling __gnet_stats_copy_basic() in the case of percpu stats.

Without this fix, rate estimators (tc qd replace dev xxx root est 1sec
4sec pfifo_fast) are utterly broken.

Fixes: 1c0d32fde5bd ("net_sched: gen_estimator: complete rewrite of rate estimators")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge git://git./pub/scm/linux/kernel/git/bpf/bpf

Alexei Starovoitov says:

====================
pull-request: bpf 2018-02-22

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) two urgent fixes for bpf_tail_call logic for x64 and arm64 JITs, from Daniel.

2) cond_resched points in percpu array alloc/free paths, from Eric.

3) lockdep and other minor fixes, from Yonghong, Arnd, Anders, Li.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

gianfar: simplify FCS handling and fix memory leak

Previously, buffer descriptors containing only the frame check sequence
(FCS) were skipped and not added to the skb. However, the page reference
count was still incremented, leading to a memory leak.

Fixing this inside gfar_add_rx_frag() is difficult due to reserved
memory handling and page reuse. Instead, move the FCS handling to
gfar_process_frame() and trim off the FCS before passing the skb up the
networking stack.

Signed-off-by: Andy Spencer <aspencer@spacex.com>
Signed-off-by: Jim Gruen <jgruen@spacex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6 sit: work around bogus gcc-8 -Wrestrict warning

gcc-8 has a new warning that detects overlapping input and output arguments
in memcpy(). It triggers for sit_init_net() calling ipip6_tunnel_clone_6rd(),
which is actually correct:

net/ipv6/sit.c: In function 'sit_init_net':
net/ipv6/sit.c:192:3: error: 'memcpy' source argument is the same as destination [-Werror=restrict]

The problem here is that the logic detecting the memcpy() arguments finds them
to be the same, but the conditional that tests for the input and output of
ipip6_tunnel_clone_6rd() to be identical is not a compile-time constant.

We know that netdev_priv(t->dev) is the same as t for a tunnel device,
and comparing "dev" directly here lets the compiler figure out as well
that 'dev == sitn->fb_tunnel_dev' when called from sit_init_net(), so
it no longer warns.

This code is old, so Cc stable to make sure that we don't get the warning
for older kernels built with new gcc.

Cc: Martin Sebor <msebor@gmail.com>
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=83456
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

macvlan: fix use-after-free in macvlan_common_newlink()

The following use-after-free was reported by KASan when running
LTP macvtap01 test on 4.16-rc2:

[10642.528443] BUG: KASAN: use-after-free in
               macvlan_common_newlink+0x12ef/0x14a0 [macvlan]
[10642.626607] Read of size 8 at addr ffff880ba49f2100 by task ip/18450
...
[10642.963873] Call Trace:
[10642.994352]  dump_stack+0x5c/0x7c
[10643.035325]  print_address_description+0x75/0x290
[10643.092938]  kasan_report+0x28d/0x390
[10643.137971]  ? macvlan_common_newlink+0x12ef/0x14a0 [macvlan]
[10643.207963]  macvlan_common_newlink+0x12ef/0x14a0 [macvlan]
[10643.275978]  macvtap_newlink+0x171/0x260 [macvtap]
[10643.334532]  rtnl_newlink+0xd4f/0x1300
...
[10646.256176] Allocated by task 18450:
[10646.299964]  kasan_kmalloc+0xa6/0xd0
[10646.343746]  kmem_cache_alloc_trace+0xf1/0x210
[10646.397826]  macvlan_common_newlink+0x6de/0x14a0 [macvlan]
[10646.464386]  macvtap_newlink+0x171/0x260 [macvtap]
[10646.522728]  rtnl_newlink+0xd4f/0x1300
...
[10647.022028] Freed by task 18450:
[10647.061549]  __kasan_slab_free+0x138/0x180
[10647.111468]  kfree+0x9e/0x1c0
[10647.147869]  macvlan_port_destroy+0x3db/0x650 [macvlan]
[10647.211411]  rollback_registered_many+0x5b9/0xb10
[10647.268715]  rollback_registered+0xd9/0x190
[10647.319675]  register_netdevice+0x8eb/0xc70
[10647.370635]  macvlan_common_newlink+0xe58/0x14a0 [macvlan]
[10647.437195]  macvtap_newlink+0x171/0x260 [macvtap]

Commit d02fd6e7d293 ("macvlan: Fix one possible double free") handles
the case when register_netdevice() invokes ndo_uninit() on error and
as a result free the port. But 'macvlan_port_get_rtnl(dev))' check
(returns dev->rx_handler_data), which was added by this commit in order
to prevent double free, is not quite correct:

* for macvlan it always returns NULL because 'lowerdev' is the one that
  was used to register rx handler (port) in macvlan_port_create() as
  well as to unregister it in macvlan_port_destroy().
* for macvtap it always returns a valid pointer because macvtap registers
  its own rx handler before macvlan_common_newlink().

Fixes: d02fd6e7d293 ("macvlan: Fix one possible double free")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

arm64: fix unwind_frame() for filtered out fn for function graph tracing

do_task_stat() calls get_wchan(), which further does unwind_frame().
unwind_frame() restores frame->pc to original value in case function
graph tracer has modified a return address (LR) in a stack frame to hook
a function return. However, if function graph tracer has hit a filtered
function, then we can't unwind it as ftrace_push_return_trace() has
biased the index(frame->graph) with a 'huge negative'
offset(-FTRACE_NOTRACE_DEPTH).

Moreover, arm64 stack walker defines index(frame->graph) as unsigned
int, which can not compare a -ve number.

Similar problem we can have with calling of walk_stackframe() from
save_stack_trace_tsk() or dump_backtrace().

This patch fixes unwind_frame() to test the index for -ve value and
restore index accordingly before we can restore frame->pc.

Reproducer:

cd /sys/kernel/debug/tracing/
echo schedule > set_graph_notrace
echo 1 > options/display-graph
echo wakeup > current_tracer
ps -ef | grep -i agent

Above commands result in:
Unable to handle kernel paging request at virtual address ffff801bd3d1e000
pgd = ffff8003cbe97c00
[ffff801bd3d1e000] *pgd=0000000000000000, *pud=0000000000000000
Internal error: Oops: 96000006 [#1] SMP
[...]
CPU: 5 PID: 11696 Comm: ps Not tainted 4.11.0+ #33
[...]
task: ffff8003c21ba000 task.stack: ffff8003cc6c0000
PC is at unwind_frame+0x12c/0x180
LR is at get_wchan+0xd4/0x134
pc : [<ffff00000808892c>] lr : [<ffff0000080860b8>] pstate: 60000145
sp : ffff8003cc6c3ab0
x29: ffff8003cc6c3ab0 x28: 0000000000000001
x27: 0000000000000026 x26: 0000000000000026
x25: 00000000000012d8 x24: 0000000000000000
x23: ffff8003c1c04000 x22: ffff000008c83000
x21: ffff8003c1c00000 x20: 000000000000000f
x19: ffff8003c1bc0000 x18: 0000fffffc593690
x17: 0000000000000000 x16: 0000000000000001
x15: 0000b855670e2b60 x14: 0003e97f22cf1d0f
x13: 0000000000000001 x12: 0000000000000000
x11: 00000000e8f4883e x10: 0000000154f47ec8
x9 : 0000000070f367c0 x8 : 0000000000000000
x7 : 00008003f7290000 x6 : 0000000000000018
x5 : 0000000000000000 x4 : ffff8003c1c03cb0
x3 : ffff8003c1c03ca0 x2 : 00000017ffe80000
x1 : ffff8003cc6c3af8 x0 : ffff8003d3e9e000

Process ps (pid: 11696, stack limit = 0xffff8003cc6c0000)
Stack: (0xffff8003cc6c3ab0 to 0xffff8003cc6c4000)
[...]
[<ffff00000808892c>] unwind_frame+0x12c/0x180
[<ffff000008305008>] do_task_stat+0x864/0x870
[<ffff000008305c44>] proc_tgid_stat+0x3c/0x48
[<ffff0000082fde0c>] proc_single_show+0x5c/0xb8
[<ffff0000082b27e0>] seq_read+0x160/0x414
[<ffff000008289e6c>] __vfs_read+0x58/0x164
[<ffff00000828b164>] vfs_read+0x88/0x144
[<ffff00000828c2e8>] SyS_read+0x60/0xc0
[<ffff0000080834a0>] __sys_trace_return+0x0/0x4

Fixes: 20380bb390a4 (arm64: ftrace: fix a stack tracer's output under function graph tracer)
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
[catalin.marinas@arm.com: replace WARN_ON with WARN_ON_ONCE]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

integrity/security: fix digsig.c build error with header file

security/integrity/digsig.c has build errors on some $ARCH due to a
missing header file, so add it.

security/integrity/digsig.c:146:2: error: implicit declaration of function 'vfree' [-Werror=implicit-function-declaration]

Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: linux-integrity@vger.kernel.org
Link: http://kisskb.ellerman.id.au/kisskb/head/13396/
Signed-off-by: James Morris <james.morris@microsoft.com>

Merge tag 'keys-fixes-20180222-2' of https://git./linux/kernel/git/dhowells/linux-fs into fixes-v4.16-rc3

Keyrings fixes.

Merge tag 'imx-drm-next-2018-02-22' of git://git.pengutronix.de/git/pza/linux into drm-fixes

drm/imx: ipu-v3 fixups and grayscale support

- Make const interrupt register arrays static, reduces object size.
- Fix device_node leaks in PRE/PRG phandle lookup functions.
- Add 8-bit and 16-bit grayscale buffer support to ipu_cpmem_set_image,
- add 10-bit and 12-bit grayscale media bus support to ipu-csi,
  to be used by the imx-media driver.

* tag 'imx-drm-next-2018-02-22' of git://git.pengutronix.de/git/pza/linux:
  gpu: ipu-csi: add 10/12-bit grayscale support to mbus_code_to_bus_cfg
  gpu: ipu-cpmem: add 16-bit grayscale support to ipu_cpmem_set_image
  gpu: ipu-v3: prg: fix device node leak in ipu_prg_lookup_by_phandle
  gpu: ipu-v3: pre: fix device node leak in ipu_pre_lookup_by_phandle
  gpu: ipu-cpmem: add 8-bit grayscale support to ipu_cpmem_set_image
  gpu: ipu-v3: make const arrays int_reg static, shrinks object size

MIPS: boot: Define __ASSEMBLY__ for its.S build

The MIPS %.its.S compiler command did not define __ASSEMBLY__, which meant
when compiler_types.h was added to kconfig.h, unexpected things appeared
(e.g. struct declarations) which should not have been present. As done in
the general %.S compiler command, __ASSEMBLY__ is now included here too.

The failure was:

    Error: arch/mips/boot/vmlinux.gz.its:201.1-2 syntax error
    FATAL ERROR: Unable to parse input tree
    /usr/bin/mkimage: Can't read arch/mips/boot/vmlinux.gz.itb.tmp: Invalid argument
    /usr/bin/mkimage Can't add hashes to FIT blob

Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 28128c61e08e ("kconfig.h: Include compiler types to avoid missed struct attributes")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'siginfo-linus' of git://git./linux/kernel/git/ebiederm/user-namespace

Pull siginfo fix from Eric Biederman:
"This fixes a build error that only shows up on blackfin"

* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
fs/signalfd: fix build error for BUS_MCEERR_AR

Merge branch 'linus' of git://git./linux/kernel/git/herbert/crypto-2.6

Pull crypto fix from Herbert Xu:
"Fix an oops in the s5p-sss driver when used with ecb(aes)"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: s5p-sss - Fix kernel Oops in AES-ECB mode

bpf, arm64: fix out of bounds access in tail call

I recently noticed a crash on arm64 when feeding a bogus index
into BPF tail call helper. The crash would not occur when the
interpreter is used, but only in case of JIT. Output looks as
follows:

  [  347.007486] Unable to handle kernel paging request at virtual address fffb850e96492510
  [...]
  [  347.043065] [fffb850e96492510] address between user and kernel address ranges
  [  347.050205] Internal error: Oops: 96000004 [#1] SMP
  [...]
  [  347.190829] x13: 0000000000000000 x12: 0000000000000000
  [  347.196128] x11: fffc047ebe782800 x10: ffff808fd7d0fd10
  [  347.201427] x9 : 0000000000000000 x8 : 0000000000000000
  [  347.206726] x7 : 0000000000000000 x6 : 001c991738000000
  [  347.212025] x5 : 0000000000000018 x4 : 000000000000ba5a
  [  347.217325] x3 : 00000000000329c4 x2 : ffff808fd7cf0500
  [  347.222625] x1 : ffff808fd7d0fc00 x0 : ffff808fd7cf0500
  [  347.227926] Process test_verifier (pid: 4548, stack limit = 0x000000007467fa61)
  [  347.235221] Call trace:
  [  347.237656]  0xffff000002f3a4fc
  [  347.240784]  bpf_test_run+0x78/0xf8
  [  347.244260]  bpf_prog_test_run_skb+0x148/0x230
  [  347.248694]  SyS_bpf+0x77c/0x1110
  [  347.251999]  el0_svc_naked+0x30/0x34
  [  347.255564] Code: 9100075a d280220a 8b0a002a d37df04b (f86b694b)
  [...]

In this case the index used in BPF r3 is the same as in r1
at the time of the call, meaning we fed a pointer as index;
here, it had the value 0xffff808fd7cf0500 which sits in x2.

While I found tail calls to be working in general (also for
hitting the error cases), I noticed the following in the code
emission:

  # bpftool p d j i 988
  [...]
  38:   ldr     w10, [x1,x10]
  3c:   cmp     w2, w10
  40:   b.ge    0x000000000000007c              <-- signed cmp
  44:   mov     x10, #0x20                      // #32
  48:   cmp     x26, x10
  4c:   b.gt    0x000000000000007c
  50:   add     x26, x26, #0x1
  54:   mov     x10, #0x110                     // #272
  58:   add     x10, x1, x10
  5c:   lsl     x11, x2, #3
  60:   ldr     x11, [x10,x11]                  <-- faulting insn (f86b694b)
  64:   cbz     x11, 0x000000000000007c
  [...]

Meaning, the tests passed because commit ddb55992b04d ("arm64:
bpf: implement bpf_tail_call() helper") was using signed compares
instead of unsigned which as a result had the test wrongly passing.

Change this but also the tail call count test both into unsigned
and cap the index as u32. Latter we did as well in 90caccdd8cc0
("bpf: fix bpf_tail_call() x64 JIT") and is needed in addition here,
too. Tested on HiSilicon Hi1616.

Result after patch:

  # bpftool p d j i 268
  [...]
  38: ldr w10, [x1,x10]
  3c: add w2, w2, #0x0
  40: cmp w2, w10
  44: b.cs 0x0000000000000080
  48: mov x10, #0x20                   // #32
  4c: cmp x26, x10
  50: b.hi 0x0000000000000080
  54: add x26, x26, #0x1
  58: mov x10, #0x110                  // #272
  5c: add x10, x1, x10
  60: lsl x11, x2, #3
  64: ldr x11, [x10,x11]
  68: cbz x11, 0x0000000000000080
  [...]

Fixes: ddb55992b04d ("arm64: bpf: implement bpf_tail_call() helper")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

bpf, x64: implement retpoline for tail call

Implement a retpoline [0] for the BPF tail call JIT'ing that converts
the indirect jump via jmp %rax that is used to make the long jump into
another JITed BPF image. Since this is subject to speculative execution,
we need to control the transient instruction sequence here as well
when CONFIG_RETPOLINE is set, and direct it into a pause + lfence loop.
The latter aligns also with what gcc / clang emits (e.g. [1]).

JIT dump after patch:

  # bpftool p d x i 1
   0: (18) r2 = map[id:1]
   2: (b7) r3 = 0
   3: (85) call bpf_tail_call#12
   4: (b7) r0 = 2
   5: (95) exit

With CONFIG_RETPOLINE:

  # bpftool p d j i 1
  [...]
  33: cmp    %edx,0x24(%rsi)
  36: jbe    0x0000000000000072  |*
  38: mov    0x24(%rbp),%eax
  3e: cmp    $0x20,%eax
  41: ja     0x0000000000000072  |
  43: add    $0x1,%eax
  46: mov    %eax,0x24(%rbp)
  4c: mov    0x90(%rsi,%rdx,8),%rax
  54: test   %rax,%rax
  57: je     0x0000000000000072  |
  59: mov    0x28(%rax),%rax
  5d: add    $0x25,%rax
  61: callq  0x000000000000006d  |+
  66: pause                      |
  68: lfence                     |
  6b: jmp    0x0000000000000066  |
  6d: mov    %rax,(%rsp)         |
  71: retq                       |
  72: mov    $0x2,%eax
  [...]

  * relative fall-through jumps in error case
  + retpoline for indirect jump

Without CONFIG_RETPOLINE:

  # bpftool p d j i 1
  [...]
  33: cmp    %edx,0x24(%rsi)
  36: jbe    0x0000000000000063  |*
  38: mov    0x24(%rbp),%eax
  3e: cmp    $0x20,%eax
  41: ja     0x0000000000000063  |
  43: add    $0x1,%eax
  46: mov    %eax,0x24(%rbp)
  4c: mov    0x90(%rsi,%rdx,8),%rax
  54: test   %rax,%rax
  57: je     0x0000000000000063  |
  59: mov    0x28(%rax),%rax
  5d: add    $0x25,%rax
  61: jmpq   *%rax               |-
  63: mov    $0x2,%eax
  [...]

  * relative fall-through jumps in error case
  - plain indirect jump as before

  [0] https://support.google.com/faqs/answer/7625886
  [1] https://github.com/gcc-mirror/gcc/commit/a31e654fa107be968b802786d747e962c2fcdb2b

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

fs/signalfd: fix build error for BUS_MCEERR_AR

Fix build error in fs/signalfd.c by using same method that is used in
kernel/signal.c: separate blocks for different signal si_code values.

./fs/signalfd.c: error: 'BUS_MCEERR_AR' undeclared (first use in this function)

Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>

rxrpc: Fix send in rxrpc_send_data_packet()

All the kernel_sendmsg() calls in rxrpc_send_data_packet() need to send
both parts of the iov[] buffer, but one of them does not. Fix it so that
it does.

Without this, short IPv6 rxrpc DATA packets may be seen that have the rxrpc
header included, but no payload.

Fixes: 5a924b8951f8 ("rxrpc: Don't store the rxrpc header in the Tx queue sk_buffs")
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: aquantia: Fix error handling in aq_pci_probe()

We should check "self->aq_hw" for allocation failure, and also we should
free it on the error paths.

Fixes: 23ee07ad3c2f ("net: aquantia: Cleanup pci functions module")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bpf: fix rcu lockdep warning for lpm_trie map_free callback

Commit 9a3efb6b661f ("bpf: fix memory leak in lpm_trie map_free callback function")
fixed a memory leak and removed unnecessary locks in map_free callback function.
Unfortrunately, it introduced a lockdep warning. When lockdep checking is turned on,
running tools/testing/selftests/bpf/test_lpm_map will have:

  [   98.294321] =============================
  [   98.294807] WARNING: suspicious RCU usage
  [   98.295359] 4.16.0-rc2+ #193 Not tainted
  [   98.295907] -----------------------------
  [   98.296486] /home/yhs/work/bpf/kernel/bpf/lpm_trie.c:572 suspicious rcu_dereference_check() usage!
  [   98.297657]
  [   98.297657] other info that might help us debug this:
  [   98.297657]
  [   98.298663]
  [   98.298663] rcu_scheduler_active = 2, debug_locks = 1
  [   98.299536] 2 locks held by kworker/2:1/54:
  [   98.300152]  #0:  ((wq_completion)"events"){+.+.}, at: [<00000000196bc1f0>] process_one_work+0x157/0x5c0
  [   98.301381]  #1:  ((work_completion)(&map->work)){+.+.}, at: [<00000000196bc1f0>] process_one_work+0x157/0x5c0

Since actual trie tree removal happens only after no other
accesses to the tree are possible, replacing
  rcu_dereference_protected(*slot, lockdep_is_held(&trie->lock))
with
  rcu_dereference_protected(*slot, 1)
fixed the issue.

Fixes: 9a3efb6b661f ("bpf: fix memory leak in lpm_trie map_free callback function")
Reported-by: Eric Dumazet <edumazet@google.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

bpf: add schedule points in percpu arrays management

syszbot managed to trigger RCU detected stalls in
bpf_array_free_percpu()

It takes time to allocate a huge percpu map, but even more time to free
it.

Since we run in process context, use cond_resched() to yield cpu if
needed.

Fixes: a10423b87a7e ("bpf: introduce BPF_MAP_TYPE_PERCPU_ARRAY map")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Merge tag 'mac80211-for-davem-2018-02-22' of git://git./linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Various fixes across the tree, the shortlog basically says it all:

  cfg80211: fix cfg80211_beacon_dup
  -> old bug in this code

  cfg80211: clear wep keys after disconnection
  -> certain ways of disconnecting left the keys

  mac80211: round IEEE80211_TX_STATUS_HEADROOM up to multiple of 4
  -> alignment issues with using 14 bytes

  mac80211: Do not disconnect on invalid operating class
  -> if the AP has a bogus operating class, let it be

  mac80211: Fix sending ADDBA response for an ongoing session
  -> don't send the same frame twice

  cfg80211: use only 1Mbps for basic rates in mesh
  -> interop issue with old versions of our code

  mac80211_hwsim: don't use WQ_MEM_RECLAIM
  -> it causes splats because it flushes work on a non-reclaim WQ

  regulatory: add NUL to request alpha2
  -> nla_put_string() issue from Kees

  mac80211: mesh: fix wrong mesh TTL offset calculation
  -> protocol issue

  mac80211: fix a possible leak of station stats
  -> error path might leak memory

  mac80211: fix calling sleeping function in atomic context
  -> percpu allocations need to be made with gfp flags
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'usb-4.16-rc3' of git://git./linux/kernel/git/gregkh/usb

Pull USB fixes from Greg KH:
"Here are a number of USB fixes for 4.16-rc3

  Nothing major, but a number of different fixes all over the place in
  the USB stack for reported issues. Mostly gadget driver fixes,
  although the typical set of xhci bugfixes are there, along with some
  new quirks additions as well.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'usb-4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (39 commits)
  Revert "usb: musb: host: don't start next rx urb if current one failed"
  usb: musb: fix enumeration after resume
  usb: cdc_acm: prevent race at write to acm while system resumes
  Add delay-init quirk for Corsair K70 RGB keyboards
  usb: ohci: Proper handling of ed_rm_list to handle race condition between usb_kill_urb() and finish_unlinks()
  usb: host: ehci: always enable interrupt for qtd completion at test mode
  usb: ldusb: add PIDs for new CASSY devices supported by this driver
  usb: renesas_usbhs: missed the "running" flag in usb_dmac with rx path
  usb: host: ehci: use correct device pointer for dma ops
  usbip: keep usbip_device sockfd state in sync with tcp_socket
  ohci-hcd: Fix race condition caused by ohci_urb_enqueue() and io_watchdog_func()
  USB: serial: option: Add support for Quectel EP06
  xhci: fix xhci debugfs errors in xhci_stop
  xhci: xhci debugfs device nodes weren't removed after device plugged out
  xhci: Fix xhci debugfs devices node disappearance after hibernation
  xhci: Fix NULL pointer in xhci debugfs
  xhci: Don't print a warning when setting link state for disabled ports
  xhci: workaround for AMD Promontory disabled ports wakeup
  usb: dwc3: core: Fix ULPI PHYs and prevent phy_get/ulpi_init during suspend/resume
  USB: gadget: udc: Add missing platform_device_put() on error in bdc_pci_probe()
  ...

Merge tag 'staging-4.16-rc2' of git://git./linux/kernel/git/gregkh/staging

Pull staging/IIO fixes from Greg KH:
"Here are a small number of staging and iio driver fixes for 4.16-rc2.

  The IIO fixes are all for reported things, and the android driver
  fixes also resolve some reported problems. The remaining fsl-mc
  Kconfig change resolves a build testing error that Arnd reported.

  All of these have been in linux-next with no reported issues"

* tag 'staging-4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  iio: buffer: check if a buffer has been set up when poll is called
  iio: adis_lib: Initialize trigger before requesting interrupt
  staging: android: ion: Zero CMA allocated memory
  staging: android: ashmem: Fix a race condition in pin ioctls
  staging: fsl-mc: fix build testing on x86
  iio: srf08: fix link error "devm_iio_triggered_buffer_setup" undefined
  staging: iio: ad5933: switch buffer mode to software
  iio: adc: stm32: fix stm32h7_adc_enable error handling
  staging: iio: adc: ad7192: fix external frequency setting
  iio: adc: aspeed: Fix error handling path

Merge tag 'char-misc-4.16-rc3' of git://git./linux/kernel/git/gregkh/char-misc

Pull char/misc driver fixes from Greg KH:
"Here are a handful of char/misc driver fixes for 4.16-rc3.

  There are some binder driver fixes to resolve reported issues in
  stress testing the recent binder changes, some extcon driver fixes,
  and a few mei driver fixes and new device ids.

  All of these, with the exception of the mei driver id additions, have
  been in linux-next for a while. I forgot to push out the mei driver id
  additions to kernel.org until today, but all build tests pass with
  them enabled"

* tag 'char-misc-4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  mei: me: add cannon point device ids for 4th device
  mei: me: add cannon point device ids
  mei: set device client to the disconnected state upon suspend.
  ANDROID: binder: synchronize_rcu() when using POLLFREE.
  binder: replace "%p" with "%pK"
  ANDROID: binder: remove WARN() for redundant txn error
  binder: check for binder_thread allocation failure in binder_poll()
  extcon: int3496: process id-pin first so that we start with the right status
  Revert "extcon: axp288: Redo charger type detection a couple of seconds after probe()"
  extcon: axp288: Constify the axp288_pwr_up_down_info array

regulatory: add NUL to request alpha2

Similar to the ancient commit a5fe8e7695dc ("regulatory: add NUL
to alpha2"), add another byte to alpha2 in the request struct so
that when we use nla_put_string(), we don't overrun anything.

Fixes: 73d54c9e74c4 ("cfg80211: add regulatory netlink multicast group")
Reported-by: Kees Cook <keescook@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Merge tag 'for-linus' of git://git./linux/kernel/git/rdma/rdma

Pull rdma fixes from Doug Ledford:
"Nothing in this is overly interesting, it's mostly your garden variety
  fixes.

  There was some work in this merge cycle around the new ioctl kABI, so
  there are fixes in here related to that (probably with more to come).

  We've also recently added new netlink support with a goal of moving
  the primary means of configuring the entire subsystem to netlink
  (eventually, this is a long term project), so there are fixes for
  that.

  Then a few bnxt_re driver fixes, and a few minor WARN_ON removals, and
  that covers this pull request. There are already a few more fixes on
  the list as of this morning, so there will certainly be more to come
  in this rc cycle ;-)

  Summary:

   - Lots of fixes for the new IOCTL interface and general uverbs flow.
     Found through testing and syzkaller

   - Bugfixes for the new resource track netlink reporting

   - Remove some unneeded WARN_ONs that were triggering for some users
     in IPoIB

   - Various fixes for the bnxt_re driver"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (27 commits)
  RDMA/uverbs: Fix kernel panic while using XRC_TGT QP type
  RDMA/bnxt_re: Avoid system hang during device un-reg
  RDMA/bnxt_re: Fix system crash during load/unload
  RDMA/bnxt_re: Synchronize destroy_qp with poll_cq
  RDMA/bnxt_re: Unpin SQ and RQ memory if QP create fails
  RDMA/bnxt_re: Disable atomic capability on bnxt_re adapters
  RDMA/restrack: don't use uaccess_kernel()
  RDMA/verbs: Check existence of function prior to accessing it
  RDMA/vmw_pvrdma: Fix usage of user response structures in ABI file
  RDMA/uverbs: Sanitize user entered port numbers prior to access it
  RDMA/uverbs: Fix circular locking dependency
  RDMA/uverbs: Fix bad unlock balance in ib_uverbs_close_xrcd
  RDMA/restrack: Increment CQ restrack object before committing
  RDMA/uverbs: Protect from command mask overflow
  IB/uverbs: Fix unbalanced unlock on error path for rdma_explicit_destroy
  IB/uverbs: Improve lockdep_check
  RDMA/uverbs: Protect from races between lookup and destroy of uobjects
  IB/uverbs: Hold the uobj write lock after allocate
  IB/uverbs: Fix possible oops with duplicate ioctl attributes
  IB/uverbs: Add ioctl support for 32bit processes
  ...

Merge tag 'riscv-for-linus-4.16-rc3-riscv_cleanups' of git://git./linux/kernel/git/palmer/riscv-linux

Pull RISC-V cleanups from Palmer Dabbelt:
"This contains a handful of small cleanups.

  The only functional change is that IRQs are now enabled during
  exception handling, which was found when some warnings triggered with
  `CONFIG_DEBUG_ATOMIC_SLEEP=y`.

  The remaining fixes should have no functional change: `sbi_save()` has
  been renamed to `parse_dtb()` reflect what it actually does, and a
  handful of unused Kconfig entries have been removed"

* tag 'riscv-for-linus-4.16-rc3-riscv_cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
  Rename sbi_save to parse_dtb to improve code readability
  RISC-V: Enable IRQ during exception handling
  riscv: Remove ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE select
  riscv: kconfig: Remove RISCV_IRQ_INTC select
  riscv: Remove ARCH_WANT_OPTIONAL_GPIOLIB select

ibmvnic: Fix early release of login buffer

The login buffer is released before the driver can perform
sanity checks between resources the driver requested and what
firmware will provide. Don't release the login buffer until
the sanity check is performed.

Fixes: 34f0f4e3f488 ("ibmvnic: Fix login buffer memory leaks")
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/smc9194: Remove bogus CONFIG_MAC reference

AFAIK the only version of smc9194.c with Mac support is the one in the
linux-mac68k CVS repo, which never made it to the mainline.

Despite that, from v2.3.45, arch/m68k/config.in listed CONFIG_SMC9194
under CONFIG_MAC. This mistake got carried over into Kconfig in v2.5.55.
(See pre-git era "[PATCH] add m68k dependencies to net driver config".)

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ipv4: Set addr_type in hash_keys for forwarded case

The result of the skb flow dissect is copied from keys to hash_keys to
ensure only the intended data is hashed. The original L4 hash patch
overlooked setting the addr_type for this case; add it.

Fixes: bf4e0a3db97eb ("net: ipv4: add support for ECMP hash policy choice")
Reported-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp_bbr: better deal with suboptimal GSO

BBR uses tcp_tso_autosize() in an attempt to probe what would be the
burst sizes and to adjust cwnd in bbr_target_cwnd() with following
gold formula :

/* Allow enough full-sized skbs in flight to utilize end systems. */
cwnd += 3 * bbr->tso_segs_goal;

But GSO can be lacking or be constrained to very small
units (ip link set dev ... gso_max_segs 2)

What we really want is to have enough packets in flight so that both
GSO and GRO are efficient.

So in the case GSO is off or downgraded, we still want to have the same
number of packets in flight as if GSO/TSO was fully operational, so
that GRO can hopefully be working efficiently.

To fix this issue, we make tcp_tso_autosize() unaware of
sk->sk_gso_max_segs

Only tcp_tso_segs() has to enforce the gso_max_segs limit.

Tested:

ethtool -K eth0 tso off gso off
tc qd replace dev eth0 root pfifo_fast

Before patch:
for f in {1..5}; do ./super_netperf 1 -H lpaa24 -- -K bbr; done
    691  (ss -temoi shows cwnd is stuck around 6 )
    667
    651
    631
    517

After patch :
# for f in {1..5}; do ./super_netperf 1 -H lpaa24 -- -K bbr; done
   1733 (ss -temoi shows cwnd is around 386 )
   1778
   1746
   1781
   1718

Fixes: 0f8782ea1497 ("tcp_bbr: add BBR congestion control")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

smsc75xx: fix smsc75xx_set_features()

If an attempt is made to disable RX checksums, USB adapter is changed
but netdev->features is not, because smsc75xx_set_features() returns a
non zero value.

This throws errors from netdev_rx_csum_fault() :
<devname>: hw csum failure

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

netlink: put module reference if dump start fails

Before, if cb->start() failed, the module reference would never be put,
because cb->cb_running is intentionally false at this point. Users are
generally annoyed by this because they can no longer unload modules that
leak references. Also, it may be possible to tediously wrap a reference
counter back to zero, especially since module.c still uses atomic_inc
instead of refcount_inc.

This patch expands the error path to simply call module_put if
cb->start() fails.

Fixes: 41c87425a1ac ("netlink: do not set cb_running if dump's start() errs")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'seccomp-v4.16-rc3' of https://git./linux/kernel/git/kees/linux into fixes-v4.16-rc3

- Fix seccomp GET_METADATA to deal with field sizes correctly (Tycho Andersen)
- Add selftest to make sure GET_METADATA doesn't regress (Tycho Andersen)

Merge branch 'akpm' (patches from Andrew)

Merge misc fixes from Andrew Morton:
"16 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mm: don't defer struct page initialization for Xen pv guests
  lib/Kconfig.debug: enable RUNTIME_TESTING_MENU
  vmalloc: fix __GFP_HIGHMEM usage for vmalloc_32 on 32b systems
  selftests/memfd: add run_fuse_test.sh to TEST_FILES
  bug.h: work around GCC PR82365 in BUG()
  mm/swap.c: make functions and their kernel-doc agree (again)
  mm/zpool.c: zpool_evictable: fix mismatch in parameter name and kernel-doc
  ida: do zeroing in ida_pre_get()
  mm, swap, frontswap: fix THP swap if frontswap enabled
  certs/blacklist_nohashes.c: fix const confusion in certs blacklist
  kernel/relay.c: limit kmalloc size to KMALLOC_MAX_SIZE
  mm, mlock, vmscan: no more skipping pagevecs
  mm: memcontrol: fix NR_WRITEBACK leak in memcg and system stats
  Kbuild: always define endianess in kconfig.h
  include/linux/sched/mm.h: re-inline mmdrop()
  tools: fix cross-compile var clobbering

efivarfs: Limit the rate for non-root to read files

Each read from a file in efivarfs results in two calls to EFI
(one to get the file size, another to get the actual data).

On X86 these EFI calls result in broadcast system management
interrupts (SMI) which affect performance of the whole system.
A malicious user can loop performing reads from efivarfs bringing
the system to its knees.

Linus suggested per-user rate limit to solve this.

So we add a ratelimit structure to "user_struct" and initialize
it for the root user for no limit. When allocating user_struct for
other users we set the limit to 100 per second. This could be used
for other places that want to limit the rate of some detrimental
user action.

In efivarfs if the limit is exceeded when reading, we take an
interruptible nap for 50ms and check the rate limit again.

Signed-off-by: Tony Luck <tony.luck@intel.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kconfig.h: Include compiler types to avoid missed struct attributes

The header files for some structures could get included in such a way
that struct attributes (specifically __randomize_layout from path.h) would
be parsed as variable names instead of attributes. This could lead to
some instances of a structure being unrandomized, causing nasty GPFs, etc.

This patch makes sure the compiler_types.h header is included in
kconfig.h so that we've always got types and struct attributes defined,
since kconfig.h is included from the compiler command line.

Reported-by: Patrick McLean <chutzpah@gentoo.org>
Root-caused-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Fixes: 3859a271a003 ("randstruct: Mark various structs for randomization")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

x86: Treat R_X86_64_PLT32 as R_X86_64_PC32

On i386, there are 2 types of PLTs, PIC and non-PIC.  PIE and shared
objects must use PIC PLT.  To use PIC PLT, you need to load
_GLOBAL_OFFSET_TABLE_ into EBX first.  There is no need for that on
x86-64 since x86-64 uses PC-relative PLT.

On x86-64, for 32-bit PC-relative branches, we can generate PLT32
relocation, instead of PC32 relocation, which can also be used as
a marker for 32-bit PC-relative branches.  Linker can always reduce
PLT32 relocation to PC32 if function is defined locally.   Local
functions should use PC32 relocation.  As far as Linux kernel is
concerned, R_X86_64_PLT32 can be treated the same as R_X86_64_PC32
since Linux kernel doesn't use PLT.

R_X86_64_PLT32 for 32-bit PC-relative branches has been enabled in
binutils master branch which will become binutils 2.31.

[ hjl is working on having better documentation on this all, but a few
  more notes from him:

   "PLT32 relocation is used as marker for PC-relative branches. Because
    of EBX, it looks odd to generate PLT32 relocation on i386 when EBX
    doesn't have GOT.

    As for symbol resolution, PLT32 and PC32 relocations are almost
    interchangeable. But when linker sees PLT32 relocation against a
    protected symbol, it can resolved locally at link-time since it is
    used on a branch instruction. Linker can't do that for PC32
    relocation"

  but for the kernel use, the two are basically the same, and this
  commit gets things building and working with the current binutils
  master   - Linus ]

Signed-off-by: H.J. Lu <hjl.tools@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

KEYS: Use individual pages in big_key for crypto buffers

kmalloc() can't always allocate large enough buffers for big_key to use for
crypto (1MB + some metadata) so we cannot use that to allocate the buffer.
Further, vmalloc'd pages can't be passed to sg_init_one() and the aead
crypto accessors cannot be called progressively and must be passed all the
data in one go (which means we can't pass the data in one block at a time).

Fix this by allocating the buffer pages individually and passing them
through a multientry scatterlist to the crypto layer. This has the bonus
advantage that we don't have to allocate a contiguous series of pages.

We then vmap() the page list and pass that through to the VFS read/write
routines.

This can trigger a warning:

WARNING: CPU: 0 PID: 60912 at mm/page_alloc.c:3883 __alloc_pages_nodemask+0xb7c/0x15f8
([<00000000002acbb6>] __alloc_pages_nodemask+0x1ee/0x15f8)
[<00000000002dd356>] kmalloc_order+0x46/0x90
[<00000000002dd3e0>] kmalloc_order_trace+0x40/0x1f8
[<0000000000326a10>] __kmalloc+0x430/0x4c0
[<00000000004343e4>] big_key_preparse+0x7c/0x210
[<000000000042c040>] key_create_or_update+0x128/0x420
[<000000000042e52c>] SyS_add_key+0x124/0x220
[<00000000007bba2c>] system_call+0xc4/0x2b0

from the keyctl/padd/useradd test of the keyutils testsuite on s390x.

Note that it might be better to shovel data through in page-sized lumps
instead as there's no particular need to use a monolithic buffer unless the
kernel itself wants to access the data.

Fixes: 13100a72f40f ("Security: Keys: Big keys stored encrypted")
Reported-by: Paul Bunyan <pbunyan@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Kirill Marinushkin <k.marinushkin@gmail.com>

X.509: fix NULL dereference when restricting key with unsupported_sig

The asymmetric key type allows an X.509 certificate to be added even if
its signature's hash algorithm is not available in the crypto API.  In
that case 'payload.data[asym_auth]' will be NULL.  But the key
restriction code failed to check for this case before trying to use the
signature, resulting in a NULL pointer dereference in
key_or_keyring_common() or in restrict_link_by_signature().

Fix this by returning -ENOPKG when the signature is unsupported.

Reproducer when all the CONFIG_CRYPTO_SHA512* options are disabled and
keyctl has support for the 'restrict_keyring' command:

    keyctl new_session
    keyctl restrict_keyring @s asymmetric builtin_trusted
    openssl req -new -sha512 -x509 -batch -nodes -outform der \
        | keyctl padd asymmetric desc @s

Fixes: a511e1af8b12 ("KEYS: Move the point of trust determination to __key_link()")
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>

X.509: fix BUG_ON() when hash algorithm is unsupported

The X.509 parser mishandles the case where the certificate's signature's
hash algorithm is not available in the crypto API.  In this case,
x509_get_sig_params() doesn't allocate the cert->sig->digest buffer;
this part seems to be intentional.  However,
public_key_verify_signature() is still called via
x509_check_for_self_signed(), which triggers the 'BUG_ON(!sig->digest)'.

Fix this by making public_key_verify_signature() return -ENOPKG if the
hash buffer has not been allocated.

Reproducer when all the CONFIG_CRYPTO_SHA512* options are disabled:

    openssl req -new -sha512 -x509 -batch -nodes -outform der \
        | keyctl padd asymmetric desc @s

Fixes: 6c2dc5ae4ab7 ("X.509: Extract signature digest and make self-signed cert checks earlier")
Reported-by: Paolo Valente <paolo.valente@linaro.org>
Cc: Paolo Valente <paolo.valente@linaro.org>
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>

PKCS#7: fix direct verification of SignerInfo signature

If none of the certificates in a SignerInfo's certificate chain match a
trusted key, nor is the last certificate signed by a trusted key, then
pkcs7_validate_trust_one() tries to check whether the SignerInfo's
signature was made directly by a trusted key. But, it actually fails to
set the 'sig' variable correctly, so it actually verifies the last
signature seen. That will only be the SignerInfo's signature if the
certificate chain is empty; otherwise it will actually be the last
certificate's signature.

This is not by itself a security problem, since verifying any of the
certificates in the chain should be sufficient to verify the SignerInfo.
Still, it's not working as intended so it should be fixed.

Fix it by setting 'sig' correctly for the direct verification case.

Fixes: 757932e6da6d ("PKCS#7: Handle PKCS#7 messages that contain no X.509 certs")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>

PKCS#7: fix certificate blacklisting

If there is a blacklisted certificate in a SignerInfo's certificate
chain, then pkcs7_verify_sig_chain() sets sinfo->blacklisted and returns
0. But, pkcs7_verify() fails to handle this case appropriately, as it
actually continues on to the line 'actual_ret = 0;', indicating that the
SignerInfo has passed verification. Consequently, PKCS#7 signature
verification ignores the certificate blacklist.

Fix this by not considering blacklisted SignerInfos to have passed
verification.

Also fix the function comment with regards to when 0 is returned.

Fixes: 03bb79315ddc ("PKCS#7: Handle blacklisted certificates")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>

PKCS#7: fix certificate chain verification

When pkcs7_verify_sig_chain() is building the certificate chain for a
SignerInfo using the certificates in the PKCS#7 message, it is passing
the wrong arguments to public_key_verify_signature().  Consequently,
when the next certificate is supposed to be used to verify the previous
certificate, the next certificate is actually used to verify itself.

An attacker can use this bug to create a bogus certificate chain that
has no cryptographic relationship between the beginning and end.

Fortunately I couldn't quite find a way to use this to bypass the
overall signature verification, though it comes very close.  Here's the
reasoning: due to the bug, every certificate in the chain beyond the
first actually has to be self-signed (where "self-signed" here refers to
the actual key and signature; an attacker might still manipulate the
certificate fields such that the self_signed flag doesn't actually get
set, and thus the chain doesn't end immediately).  But to pass trust
validation (pkcs7_validate_trust()), either the SignerInfo or one of the
certificates has to actually be signed by a trusted key.  Since only
self-signed certificates can be added to the chain, the only way for an
attacker to introduce a trusted signature is to include a self-signed
trusted certificate.

But, when pkcs7_validate_trust_one() reaches that certificate, instead
of trying to verify the signature on that certificate, it will actually
look up the corresponding trusted key, which will succeed, and then try
to verify the *previous* certificate, which will fail.  Thus, disaster
is narrowly averted (as far as I could tell).

Fixes: 6c2dc5ae4ab7 ("X.509: Extract signature digest and make self-signed cert checks earlier")
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>

selftests/bpf/test_maps: exit child process without error in ENOMEM case

test_maps contains a series of stress tests, and previously it will break the
rest tests when it failed to alloc memory.
-----------------------
Failed to create hashmap key=8 value=262144 'Cannot allocate memory'
Failed to create hashmap key=16 value=262144 'Cannot allocate memory'
Failed to create hashmap key=8 value=262144 'Cannot allocate memory'
Failed to create hashmap key=8 value=262144 'Cannot allocate memory'
test_maps: test_maps.c:955: run_parallel: Assertion `status == 0' failed.
Aborted
not ok 1..3 selftests: test_maps [FAIL]
-----------------------
after this patch, the rest tests will be continue when it occurs an ENOMEM failure

CC: Alexei Starovoitov <alexei.starovoitov@gmail.com>
CC: Philip Li <philip.li@intel.com>
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Li Zhijian <zhijianx.li@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

arm64: Enforce BBM for huge IO/VMAP mappings

ioremap_page_range doesn't honour break-before-make and attempts to put
down huge mappings (using p*d_set_huge) over the top of pre-existing
table entries. This leads to us leaking page table memory and also gives
rise to TLB conflicts and spurious aborts, which have been seen in
practice on Cortex-A75.

Until this has been resolved, refuse to put block mappings when the
existing entry is found to be present.

Fixes: 324420bf91f60 ("arm64: add support for ioremap() block mappings")
Reported-by: Hanjun Guo <hanjun.guo@linaro.org>
Reported-by: Lei Li <lious.lilei@hisilicon.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>

i2c: designware: Consider SCL GPIO optional

GPIO library can return -ENOSYS for the failed request.
Instead of failing ->probe() in this case override error code to 0.

Fixes: ca382f5b38f3 ("i2c: designware: add i2c gpio recovery option")
Reported-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

i2c: busses: i2c-sirf: Fix spelling: "formular" -> "formula".

Fix spelling.

Signed-off-by: Patryk Kocielnik <patryk.kocielnik@gmail.com>
[wsa: fixed "Initialization", too]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

i2c: bcm2835: Set up the rising/falling edge delays

We were leaving them in the power on state (or the state the firmware
had set up for some client, if we were taking over from them). The
boot state was 30 core clocks, when we actually want to sample some
time after (to make sure that the new input bit has actually arrived).

Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org

seccomp: add a selftest for get_metadata

Let's test that we get the flags correctly, and that we preserve the filter
index across the ptrace(PTRACE_SECCOMP_GET_METADATA) correctly.

Signed-off-by: Tycho Andersen <tycho@tycho.ws>
CC: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>

ptrace, seccomp: tweak get_metadata behavior slightly

Previously if users passed a small size for the input structure size, they
would get get odd behavior. It doesn't make sense to pass a structure
smaller than at least filter_off size, so let's just give -EINVAL in this
case.

This changes userspace visible behavior, but was only introduced in commit
26500475ac1b ("ptrace, seccomp: add support for retrieving seccomp
metadata") in 4.16-rc2, so should be safe to change if merged before then.

Reported-by: Eugene Syromiatnikov <esyr@redhat.com>
Signed-off-by: Tycho Andersen <tycho@tycho.ws>
CC: Kees Cook <keescook@chromium.org>
CC: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Kees Cook <keescook@chromium.org>

seccomp, ptrace: switch get_metadata types to arch independent

Commit 26500475ac1b ("ptrace, seccomp: add support for retrieving seccomp
metadata") introduced `struct seccomp_metadata`, which contained unsigned
longs that should be arch independent. The type of the flags member was
chosen to match the corresponding argument to seccomp(), and so we need
something at least as big as unsigned long. My understanding is that __u64
should fit the bill, so let's switch both types to that.

While this is userspace facing, it was only introduced in 4.16-rc2, and so
should be safe assuming it goes in before then.

Reported-by: "Dmitry V. Levin" <ldv@altlinux.org>
Signed-off-by: Tycho Andersen <tycho@tycho.ws>
CC: Kees Cook <keescook@chromium.org>
CC: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: "Dmitry V. Levin" <ldv@altlinux.org>
Signed-off-by: Kees Cook <keescook@chromium.org>

selftests/bpf: update gitignore with test_libbpf_open

bpf builds a test program for loading BPF ELF files. Add the executable
to the .gitignore list.

Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Daniel Díaz <daniel.diaz@linaro.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

selftests/bpf: tcpbpf_kern: use in6_* macros from glibc

Both glibc and the kernel have in6_* macros definitions. Build fails
because it picks up wrong in6_* macro from the kernel header and not the
header from glibc.

Fixes build error below:
clang -I. -I./include/uapi -I../../../include/uapi
     -Wno-compare-distinct-pointer-types \
         -O2 -target bpf -emit-llvm -c test_tcpbpf_kern.c -o - |      \
llc -march=bpf -mcpu=generic -filetype=obj
     -o .../tools/testing/selftests/bpf/test_tcpbpf_kern.o
In file included from test_tcpbpf_kern.c:12:
.../netinet/in.h:101:5: error: expected identifier
    IPPROTO_HOPOPTS = 0,   /* IPv6 Hop-by-Hop options.  */
    ^
.../linux/in6.h:131:26: note: expanded from macro 'IPPROTO_HOPOPTS'
                                ^
In file included from test_tcpbpf_kern.c:12:
/usr/include/netinet/in.h:103:5: error: expected identifier
    IPPROTO_ROUTING = 43,  /* IPv6 routing header.  */
    ^
.../linux/in6.h:132:26: note: expanded from macro 'IPPROTO_ROUTING'
                                ^
In file included from test_tcpbpf_kern.c:12:
.../netinet/in.h:105:5: error: expected identifier
    IPPROTO_FRAGMENT = 44, /* IPv6 fragmentation header.  */
    ^

Since both glibc and the kernel have in6_* macros definitions, use the
one from glibc.  Kernel headers will check for previous libc definitions
by including include/linux/libc-compat.h.

Reported-by: Daniel Díaz <daniel.diaz@linaro.org>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Daniel Díaz <daniel.diaz@linaro.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

bpf: clean up unused-variable warning

The only user of this variable is inside of an #ifdef, causing
a warning without CONFIG_INET:

net/core/filter.c: In function '____bpf_sock_ops_cb_flags_set':
net/core/filter.c:3382:6: error: unused variable 'val' [-Werror=unused-variable]
int val = argval & BPF_SOCK_OPS_ALL_CB_FLAGS;

This replaces the #ifdef with a nicer IS_ENABLED() check that
makes the code more readable and avoids the warning.

Fixes: b13d88072172 ("bpf: Adds field bpf_sock_ops_cb_flags to tcp_sock")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

mm: don't defer struct page initialization for Xen pv guests

Commit f7f99100d8d9 ("mm: stop zeroing memory during allocation in
vmemmap") broke Xen pv domains in some configurations, as the "Pinned"
information in struct page of early page tables could get lost.

This will lead to the kernel trying to write directly into the page
tables instead of asking the hypervisor to do so.  The result is a crash
like the following:

  BUG: unable to handle kernel paging request at ffff8801ead19008
  IP: xen_set_pud+0x4e/0xd0
  PGD 1c0a067 P4D 1c0a067 PUD 23a0067 PMD 1e9de0067 PTE 80100001ead19065
  Oops: 0003 [#1] PREEMPT SMP
  Modules linked in:
  CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.14.0-default+ #271
  Hardware name: Dell Inc. Latitude E6440/0159N7, BIOS A07 06/26/2014
  task: ffffffff81c10480 task.stack: ffffffff81c00000
  RIP: e030:xen_set_pud+0x4e/0xd0
  Call Trace:
   __pmd_alloc+0x128/0x140
   ioremap_page_range+0x3f4/0x410
   __ioremap_caller+0x1c3/0x2e0
   acpi_os_map_iomem+0x175/0x1b0
   acpi_tb_acquire_table+0x39/0x66
   acpi_tb_validate_table+0x44/0x7c
   acpi_tb_verify_temp_table+0x45/0x304
   acpi_reallocate_root_table+0x12d/0x141
   acpi_early_init+0x4d/0x10a
   start_kernel+0x3eb/0x4a1
   xen_start_kernel+0x528/0x532
  Code: 48 01 e8 48 0f 42 15 a2 fd be 00 48 01 d0 48 ba 00 00 00 00 00 ea ff ff 48 c1 e8 0c 48 c1 e0 06 48 01 d0 48 8b 00 f6 c4 02 75 5d <4c> 89 65 00 5b 5d 41 5c c3 65 8b 05 52 9f fe 7e 89 c0 48 0f a3
  RIP: xen_set_pud+0x4e/0xd0 RSP: ffffffff81c03cd8
  CR2: ffff8801ead19008
  ---[ end trace 38eca2e56f1b642e ]---

Avoid this problem by not deferring struct page initialization when
running as Xen pv guest.

Pavel said:

: This is unique for Xen, so this particular issue won't effect other
: configurations.  I am going to investigate if there is a way to
: re-enable deferred page initialization on xen guests.

[akpm@linux-foundation.org: explicitly include xen.h]
Link: http://lkml.kernel.org/r/20180216154101.22865-1-jgross@suse.com
Fixes: f7f99100d8d95d ("mm: stop zeroing memory during allocation in vmemmap")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Cc: Steven Sistare <steven.sistare@oracle.com>
Cc: Daniel Jordan <daniel.m.jordan@oracle.com>
Cc: Bob Picco <bob.picco@oracle.com>
Cc: <stable@vger.kernel.org> [4.15.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

lib/Kconfig.debug: enable RUNTIME_TESTING_MENU

Commit d3deafaa8b5c ("lib/: make RUNTIME_TESTS a menuconfig to ease
disabling it all") causes a regression when using runtime tests due to
it defaults RUNTIME_TESTING_MENU to not set.

Link: http://lkml.kernel.org/r/20180214133015.10090-1-anders.roxell@linaro.org
Fixes: d3deafaa8b5c ("lib/: make RUNTIME_TESTS a menuconfig to easedisabling it all")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Cc: Vincent Legoll <vincent.legoll@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Byungchul Park <byungchul.park@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

vmalloc: fix __GFP_HIGHMEM usage for vmalloc_32 on 32b systems

Kai Heng Feng has noticed that BUG_ON(PageHighMem(pg)) triggers in
drivers/media/common/saa7146/saa7146_core.c since 19809c2da28a ("mm,
vmalloc: use __GFP_HIGHMEM implicitly").

saa7146_vmalloc_build_pgtable uses vmalloc_32 and it is reasonable to
expect that the resulting page is not in highmem.  The above commit
aimed to add __GFP_HIGHMEM only for those requests which do not specify
any zone modifier gfp flag.  vmalloc_32 relies on GFP_VMALLOC32 which
should do the right thing.  Except it has been missed that GFP_VMALLOC32
is an alias for GFP_KERNEL on 32b architectures.  Thanks to Matthew to
notice this.

Fix the problem by unconditionally setting GFP_DMA32 in GFP_VMALLOC32
for !64b arches (as a bailout).  This should do the right thing and use
ZONE_NORMAL which should be always below 4G on 32b systems.

Debugged by Matthew Wilcox.

[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/20180212095019.GX21609@dhcp22.suse.cz
Fixes: 19809c2da28a ("mm, vmalloc: use __GFP_HIGHMEM implicitly”)
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Kai Heng Feng <kai.heng.feng@canonical.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Laura Abbott <labbott@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

selftests/memfd: add run_fuse_test.sh to TEST_FILES

While testing memfd tests, there is a missing script, as reported by
kselftest:

./run_tests.sh: line 7: ./run_fuse_test.sh: No such file or directory

Link: http://lkml.kernel.org/r/1517955779-11386-1-git-send-email-daniel.diaz@linaro.org
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

bug.h: work around GCC PR82365 in BUG()

Looking at functions with large stack frames across all architectures
led me discovering that BUG() suffers from the same problem as
fortify_panic(), which I've added a workaround for already.

In short, variables that go out of scope by calling a noreturn function
or __builtin_unreachable() keep using stack space in functions
afterwards.

A workaround that was identified is to insert an empty assembler
statement just before calling the function that doesn't return.  I'm
adding a macro "barrier_before_unreachable()" to document this, and
insert calls to that in all instances of BUG() that currently suffer
from this problem.

The files that saw the largest change from this had these frame sizes
before, and much less with my patch:

  fs/ext4/inode.c:82:1: warning: the frame size of 1672 bytes is larger than 800 bytes [-Wframe-larger-than=]
  fs/ext4/namei.c:434:1: warning: the frame size of 904 bytes is larger than 800 bytes [-Wframe-larger-than=]
  fs/ext4/super.c:2279:1: warning: the frame size of 1160 bytes is larger than 800 bytes [-Wframe-larger-than=]
  fs/ext4/xattr.c:146:1: warning: the frame size of 1168 bytes is larger than 800 bytes [-Wframe-larger-than=]
  fs/f2fs/inode.c:152:1: warning: the frame size of 1424 bytes is larger than 800 bytes [-Wframe-larger-than=]
  net/netfilter/ipvs/ip_vs_core.c:1195:1: warning: the frame size of 1068 bytes is larger than 800 bytes [-Wframe-larger-than=]
  net/netfilter/ipvs/ip_vs_core.c:395:1: warning: the frame size of 1084 bytes is larger than 800 bytes [-Wframe-larger-than=]
  net/netfilter/ipvs/ip_vs_ftp.c:298:1: warning: the frame size of 928 bytes is larger than 800 bytes [-Wframe-larger-than=]
  net/netfilter/ipvs/ip_vs_ftp.c:418:1: warning: the frame size of 908 bytes is larger than 800 bytes [-Wframe-larger-than=]
  net/netfilter/ipvs/ip_vs_lblcr.c:718:1: warning: the frame size of 960 bytes is larger than 800 bytes [-Wframe-larger-than=]
  drivers/net/xen-netback/netback.c:1500:1: warning: the frame size of 1088 bytes is larger than 800 bytes [-Wframe-larger-than=]

In case of ARC and CRIS, it turns out that the BUG() implementation
actually does return (or at least the compiler thinks it does),
resulting in lots of warnings about uninitialized variable use and
leaving noreturn functions, such as:

  block/cfq-iosched.c: In function 'cfq_async_queue_prio':
  block/cfq-iosched.c:3804:1: error: control reaches end of non-void function [-Werror=return-type]
  include/linux/dmaengine.h: In function 'dma_maxpq':
  include/linux/dmaengine.h:1123:1: error: control reaches end of non-void function [-Werror=return-type]

This makes them call __builtin_trap() instead, which should normally
dump the stack and kill the current process, like some of the other
architectures already do.

I tried adding barrier_before_unreachable() to panic() and
fortify_panic() as well, but that had very little effect, so I'm not
submitting that patch.

Vineet said:

: For ARC, it is double win.
:
: 1. Fixes 3 -Wreturn-type warnings
:
: | ../net/core/ethtool.c:311:1: warning: control reaches end of non-void function
: [-Wreturn-type]
: | ../kernel/sched/core.c:3246:1: warning: control reaches end of non-void function
: [-Wreturn-type]
: | ../include/linux/sunrpc/svc_xprt.h:180:1: warning: control reaches end of
: non-void function [-Wreturn-type]
:
: 2.  bloat-o-meter reports code size improvements as gcc elides the
:    generated code for stack return.

Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=82365
Link: http://lkml.kernel.org/r/20171219114112.939391-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arch/arc]
Tested-by: Vineet Gupta <vgupta@synopsys.com> [arch/arc]
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Christopher Li <sparse@chrisli.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: "Steven Rostedt (VMware)" <rostedt@goodmis.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/swap.c: make functions and their kernel-doc agree (again)

There was a conflict between the commit e02a9f048ef7 ("mm/swap.c: make
functions and their kernel-doc agree") and the commit f144c390f905 ("mm:
docs: fix parameter names mismatch") that both tried to fix mismatch
betweeen pagevec_lookup_entries() parameter names and their description.

Since nr_entries is a better name for the parameter, fix the description
again.

Link: http://lkml.kernel.org/r/1518116946-20947-1-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm/zpool.c: zpool_evictable: fix mismatch in parameter name and kernel-doc

[akpm@linux-foundation.org: add colon, per Randy]
Link: http://lkml.kernel.org/r/1518116984-21141-1-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ida: do zeroing in ida_pre_get()

As far as I can tell, the only place the per-cpu ida_bitmap is populated
is in ida_pre_get.  The pre-allocated element is stolen in two places in
ida_get_new_above, in both cases immediately followed by a memset(0).

Since ida_get_new_above is called with locks held, do the zeroing in
ida_pre_get, or rather let kmalloc() do it.  Also, apparently gcc
generates ~44 bytes of code to do a memset(, 0, 128):

  $ scripts/bloat-o-meter vmlinux.{0,1}
  add/remove: 0/0 grow/shrink: 2/1 up/down: 5/-88 (-83)
  Function                                     old     new   delta
  ida_pre_get                                  115     119      +4
  vermagic                                      27      28      +1
  ida_get_new_above                            715     627     -88

Link: http://lkml.kernel.org/r/20180108225634.15340-1-linux@rasmusvillemoes.dk
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Eric Biggers <ebiggers@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm, swap, frontswap: fix THP swap if frontswap enabled

It was reported by Sergey Senozhatsky that if THP (Transparent Huge
Page) and frontswap (via zswap) are both enabled, when memory goes low
so that swap is triggered, segfault and memory corruption will occur in
random user space applications as follow,

kernel: urxvt[338]: segfault at 20 ip 00007fc08889ae0d sp 00007ffc73a7fc40 error 6 in libc-2.26.so[7fc08881a000+1ae000]
#0  0x00007fc08889ae0d _int_malloc (libc.so.6)
#1  0x00007fc08889c2f3 malloc (libc.so.6)
#2  0x0000560e6004bff7 _Z14rxvt_wcstoutf8PKwi (urxvt)
#3  0x0000560e6005e75c n/a (urxvt)
#4  0x0000560e6007d9f1 _ZN16rxvt_perl_interp6invokeEP9rxvt_term9hook_typez (urxvt)
#5  0x0000560e6003d988 _ZN9rxvt_term9cmd_parseEv (urxvt)
#6  0x0000560e60042804 _ZN9rxvt_term6pty_cbERN2ev2ioEi (urxvt)
#7  0x0000560e6005c10f _Z17ev_invoke_pendingv (urxvt)
#8  0x0000560e6005cb55 ev_run (urxvt)
#9  0x0000560e6003b9b9 main (urxvt)
#10 0x00007fc08883af4a __libc_start_main (libc.so.6)
#11 0x0000560e6003f9da _start (urxvt)

After bisection, it was found the first bad commit is bd4c82c22c36 ("mm,
THP, swap: delay splitting THP after swapped out").

The root cause is as follows:

When the pages are written to swap device during swapping out in
swap_writepage(), zswap (fontswap) is tried to compress the pages to
improve performance.  But zswap (frontswap) will treat THP as a normal
page, so only the head page is saved.  After swapping in, tail pages
will not be restored to their original contents, causing memory
corruption in the applications.

This is fixed by refusing to save page in the frontswap store functions
if the page is a THP.  So that the THP will be swapped out to swap
device.

Another choice is to split THP if frontswap is enabled.  But it is found
that the frontswap enabling isn't flexible.  For example, if
CONFIG_ZSWAP=y (cannot be module), frontswap will be enabled even if
zswap itself isn't enabled.

Frontswap has multiple backends, to make it easy for one backend to
enable THP support, the THP checking is put in backend frontswap store
functions instead of the general interfaces.

Link: http://lkml.kernel.org/r/20180209084947.22749-1-ying.huang@intel.com
Fixes: bd4c82c22c367e068 ("mm, THP, swap: delay splitting THP after swapped out")
Signed-off-by: "Huang, Ying" <ying.huang@intel.com>
Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Suggested-by: Minchan Kim <minchan@kernel.org> [put THP checking in backend]
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Shaohua Li <shli@kernel.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: <stable@vger.kernel.org> [4.14]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

certs/blacklist_nohashes.c: fix const confusion in certs blacklist

const must be marked __initconst, not __initdata.

Link: http://lkml.kernel.org/r/20171222001335.1987-1-andi@firstfloor.org
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

kernel/relay.c: limit kmalloc size to KMALLOC_MAX_SIZE

chan->n_subbufs is set by the user and relay_create_buf() does a kmalloc()
of chan->n_subbufs * sizeof(size_t *).

kmalloc_slab() will generate a warning when this fails if
chan->subbufs * sizeof(size_t *) > KMALLOC_MAX_SIZE.

Limit chan->n_subbufs to the maximum allowed kmalloc() size.

Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1802061216100.122576@chino.kir.corp.google.com
Fixes: f6302f1bcd75 ("relay: prevent integer overflow in relay_open()")
Signed-off-by: David Rientjes <rientjes@google.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm, mlock, vmscan: no more skipping pagevecs

When a thread mlocks an address space backed either by file pages which
are currently not present in memory or swapped out anon pages (not in
swapcache), a new page is allocated and added to the local pagevec
(lru_add_pvec), I/O is triggered and the thread then sleeps on the page.
On I/O completion, the thread can wake on a different CPU, the mlock
syscall will then sets the PageMlocked() bit of the page but will not be
able to put that page in unevictable LRU as the page is on the pagevec
of a different CPU.  Even on drain, that page will go to evictable LRU
because the PageMlocked() bit is not checked on pagevec drain.

The page will eventually go to right LRU on reclaim but the LRU stats
will remain skewed for a long time.

This patch puts all the pages, even unevictable, to the pagevecs and on
the drain, the pages will be added on their LRUs correctly by checking
their evictability.  This resolves the mlocked pages on pagevec of other
CPUs issue because when those pagevecs will be drained, the mlocked file
pages will go to unevictable LRU.  Also this makes the race with munlock
easier to resolve because the pagevec drains happen in LRU lock.

However there is still one place which makes a page evictable and does
PageLRU check on that page without LRU lock and needs special attention.
TestClearPageMlocked() and isolate_lru_page() in clear_page_mlock().

#0: __pagevec_lru_add_fn #1: clear_page_mlock

SetPageLRU() if (!TestClearPageMlocked())
  return
smp_mb() // <--required
// inside does PageLRU
if (!PageMlocked()) if (isolate_lru_page())
  move to evictable LRU   putback_lru_page()
else
  move to unevictable LRU

In '#1', TestClearPageMlocked() provides full memory barrier semantics
and thus the PageLRU check (inside isolate_lru_page) can not be
reordered before it.

In '#0', without explicit memory barrier, the PageMlocked() check can be
reordered before SetPageLRU().  If that happens, '#0' can put a page in
unevictable LRU and '#1' might have just cleared the Mlocked bit of that
page but fails to isolate as PageLRU fails as '#0' still hasn't set
PageLRU bit of that page.  That page will be stranded on the unevictable
LRU.

There is one (good) side effect though.  Without this patch, the pages
allocated for System V shared memory segment are added to evictable LRUs
even after shmctl(SHM_LOCK) on that segment.  This patch will correctly
put such pages to unevictable LRU.

Link: http://lkml.kernel.org/r/20171121211241.18877-1-shakeelb@google.com
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Jérôme Glisse <jglisse@redhat.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Greg Thelen <gthelen@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Shaohua Li <shli@fb.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mm: memcontrol: fix NR_WRITEBACK leak in memcg and system stats

After commit a983b5ebee57 ("mm: memcontrol: fix excessive complexity in
memory.stat reporting"), we observed slowly upward creeping NR_WRITEBACK
counts over the course of several days, both the per-memcg stats as well
as the system counter in e.g. /proc/meminfo.

The conversion from full per-cpu stat counts to per-cpu cached atomic
stat counts introduced an irq-unsafe RMW operation into the updates.

Most stat updates come from process context, but one notable exception
is the NR_WRITEBACK counter. While writebacks are issued from process
context, they are retired from (soft)irq context.

When writeback completions interrupt the RMW counter updates of new
writebacks being issued, the decs from the completions are lost.

Since the global updates are routed through the joint lruvec API, both
the memcg counters as well as the system counters are affected.

This patch makes the joint stat and event API irq safe.

Link: http://lkml.kernel.org/r/20180203082353.17284-1-hannes@cmpxchg.org
Fixes: a983b5ebee57 ("mm: memcontrol: fix excessive complexity in memory.stat reporting")
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Debugged-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Rik van Riel <riel@surriel.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Kbuild: always define endianess in kconfig.h

Build testing with LTO found a couple of files that get compiled
differently depending on whether asm/byteorder.h gets included early
enough or not.  In particular, include/asm-generic/qrwlock_types.h is
affected by this, but there are probably others as well.

The symptom is a series of LTO link time warnings, including these:

    net/netlabel/netlabel_unlabeled.h:223: error: type of 'netlbl_unlhsh_add' does not match original declaration [-Werror=lto-type-mismatch]
     int netlbl_unlhsh_add(struct net *net,
    net/netlabel/netlabel_unlabeled.c:377: note: 'netlbl_unlhsh_add' was previously declared here

    include/net/ipv6.h:360: error: type of 'ipv6_renew_options_kern' does not match original declaration [-Werror=lto-type-mismatch]
     ipv6_renew_options_kern(struct sock *sk,
    net/ipv6/exthdrs.c:1162: note: 'ipv6_renew_options_kern' was previously declared here

    net/core/dev.c:761: note: 'dev_get_by_name_rcu' was previously declared here
     struct net_device *dev_get_by_name_rcu(struct net *net, const char *name)
    net/core/dev.c:761: note: code may be misoptimized unless -fno-strict-aliasing is used

    drivers/gpu/drm/i915/i915_drv.h:3377: error: type of 'i915_gem_object_set_to_wc_domain' does not match original declaration [-Werror=lto-type-mismatch]
     i915_gem_object_set_to_wc_domain(struct drm_i915_gem_object *obj, bool write);
    drivers/gpu/drm/i915/i915_gem.c:3639: note: 'i915_gem_object_set_to_wc_domain' was previously declared here

    include/linux/debugfs.h:92:9: error: type of 'debugfs_attr_read' does not match original declaration [-Werror=lto-type-mismatch]
     ssize_t debugfs_attr_read(struct file *file, char __user *buf,
    fs/debugfs/file.c:318: note: 'debugfs_attr_read' was previously declared here

    include/linux/rwlock_api_smp.h:30: error: type of '_raw_read_unlock' does not match original declaration [-Werror=lto-type-mismatch]
     void __lockfunc _raw_read_unlock(rwlock_t *lock) __releases(lock);
    kernel/locking/spinlock.c:246:26: note: '_raw_read_unlock' was previously declared here

    include/linux/fs.h:3308:5: error: type of 'simple_attr_open' does not match original declaration [-Werror=lto-type-mismatch]
     int simple_attr_open(struct inode *inode, struct file *file,
    fs/libfs.c:795: note: 'simple_attr_open' was previously declared here

All of the above are caused by include/asm-generic/qrwlock_types.h
failing to include asm/byteorder.h after commit e0d02285f16e
("locking/qrwlock: Use 'struct qrwlock' instead of 'struct __qrwlock'")
in linux-4.15.

Similar bugs may or may not exist in older kernels as well, but there is
no easy way to test those with link-time optimizations, and kernels
before 4.14 are harder to fix because they don't have Babu's patch
series

We had similar issues with CONFIG_ symbols in the past and ended up
always including the configuration headers though linux/kconfig.h.  This
works around the issue through that same file, defining either
__BIG_ENDIAN or __LITTLE_ENDIAN depending on CONFIG_CPU_BIG_ENDIAN,
which is now always set on all architectures since commit 4c97a0c8fee3
("arch: define CPU_BIG_ENDIAN for all fixed big endian archs").

Link: http://lkml.kernel.org/r/20180202154104.1522809-2-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Babu Moger <babu.moger@amd.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Nicolas Pitre <nico@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

include/linux/sched/mm.h: re-inline mmdrop()

As Peter points out, Doing a CALL+RET for just the decrement is a bit silly.

Fixes: d70f2a14b72a4bc ("include/linux/sched/mm.h: uninline mmdrop_async(), etc")
Acked-by: Peter Zijlstra (Intel) <peterz@infraded.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>