git.openwrt.org Git - openwrt/staging/jogo.git/log

libnftnl: update to 1.0.9

Also, drop unsupported configure options.

Don't use git retrieve but released tarball instead.

Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>

kernel: backport fix for nftables on big Endian

nftables 0.8.1 generates some new commands which will not work without
this on big endian systems. This patch is included in Linux 4.11 and
later.

My rule matching a TCP port was not working:
nft add rule ip foo bar ct state new tcp dport 22 accept

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

tools/tar: update to 1.30

update GNU tar to 1.30

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>

kernel: bump 4.4 to 4.4.112

Refresh patches.
Remove upstreamed patches:

target/linux/generic/patches-4.4/030-2-smsc75xx-use-skb_cow_head-to-deal-with-cloned-skbs.patch
target/linux/generic/patches-4.4/030-3-cx82310_eth-use-skb_cow_head-to-deal-with-cloned-skb.patch
target/linux/generic/patches-4.4/030-4-sr9700-use-skb_cow_head-to-deal-with-cloned-skbs.patch
target/linux/generic/patches-4.4/030-5-lan78xx-use-skb_cow_head-to-deal-with-cloned-skbs.patch

CVEs completely or partially addressed:

CVE-2017-5715
CVE-2017-5753
CVE-2017-17741
CVE-2017-1000410

Compile-tested: ar71xx Archer C7 v2
Run-tested: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>

kernel: bump 4.9 to 4.9.77

Refresh patches.
Remove upstreamed patches:

target/linux/generic/backport-4.9/023-2-smsc75xx-use-skb_cow_head-to-deal-with-cloned-skbs.patch
target/linux/generic/backport-4.9/023-3-cx82310_eth-use-skb_cow_head-to-deal-with-cloned-skb.patch
target/linux/generic/backport-4.9/023-4-sr9700-use-skb_cow_head-to-deal-with-cloned-skbs.patch
target/linux/generic/backport-4.9/023-5-lan78xx-use-skb_cow_head-to-deal-with-cloned-skbs.patch

CVEs completely or partially addressed:

CVE-2017-5715
CVE-2017-5753
CVE-2017-17741
CVE-2017-1000410

Compile-tested: ar71xx Archer C7 v2
Run-tested: ar71xx Archer C7 v2

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

kernel: bump 4.14 to 4.14.14

Refresh patches.

CVEs completely or partially addressed:

CVE-2017-5715
CVE-2017-5753
CVE-2017-17741
CVE-2017-1000410

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

kernel/4.{4, 9}: add manufacturer ID for Winbond NANDs

Some MikroTik devices are using a Winbond NAND flash. Linux treats
it as an unknown NAND before version 4.11:

  nand: device found, Manufacturer ID: 0xef, Chip ID: 0xf1
  nand: Unknown NAND 128MiB 3,3V 8-bit
  nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64

Backport a patch from 4.11 to show the manufacturer correctly:

  nand: device found, Manufacturer ID: 0xef, Chip ID: 0xf1
  nand: Winbond NAND 128MiB 3,3V 8-bit
  nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64

Tested on a MikroTik R951Ui-2HnD board.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>

dnsmasq: backport validation fix in dnssec security fix

A DNSSEC validation error was introduced in the fix for CVE-2017-15107

Backport the upstream fix to the fix (a simple typo)

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>

dnsmasq: backport dnssec security fix

CVE-2017-15107

An interesting problem has turned up in DNSSEC validation. It turns out
that NSEC records expanded from wildcards are allowed, so a domain can
include an NSEC record for *.example.org and an actual query reply could
expand that to anything in example.org and still have it signed by the
signature for the wildcard. So, for example

!.example.org NSEC zz.example.org

is fine.

The problem is that most implementers (your author included, but also
the Google public DNS people, powerdns and Unbound) then took that
record to prove the nothing exists between !.example.org and
zz.example.org, whereas in fact it only provides that proof between
*.example.org and zz.example.org.

This gives an attacker a way to prove that anything between
!.example.org and *.example.org doesn't exists, when it may well do so.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>

ipq806x: remove merged ipq4019 patch

The patch 0022-dts-ipq4019-support-ARMv7-PMU.patch
was merged into 4.8-rc1.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[refresh patches]
Signed-off-by: Mathias Kresin <dev@kresin.me>

ipq806x: remove dependency on non-existent kmod

During the integration of the ipq40xx target,
the phy drivers were included into the ipq806x's
target kernel config.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>

ipq-wifi: align AVM FRITZ!Box 4040's board-2.bin package

This patch renames the AVM FRITZ!Box 4040's board-2.bin
file and package to match the 'vendor_product' format.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>

ipq806x: overhaul AVM FRITZ!box 4040 device-tree file

This patch aligns the device-tree file with the latest
guidelines.
- No longer include qcom-ipq4019-ap.dk01.1.dtsi. This
   file is only partially upstream and therefore subjected
   to changes that might not be compatible with the board.

   As a result, the definitions from the file have been
   copied into this dts.

- exclusively use decimal GPIO addresses.

- reorganize the reserved-memory layout to waste less
   memory. There's no point in keeping the u-boot loader
   around. This should also make it possible    to create
   an image that will boot with the original EVA/ADAM2 loader
   without needing to install the modified u-boot loader.
   And finally mark the "tz-apps" as reusable.
   There isn't a way to  upload apps to the trust-zone in OpenWrt
   yet. But it might see some use in the future as a "secure"
   key-store/TPM.

- sort the first-level nodes alphabetically.
- sort nodes with an address by the address.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>

firmware: ath10k-firmware: update QCA988x firmware to 10.2.4-1.0-00033

This patch updates ath10k-firmware to use the
firmware-5.bin_10.2.4-1.0-00033 firmware for the QCA988x.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>

firmware: ath10k-firmware: update QCA9887 firmware to 10.2.4-1.0-00033

This patch updates ath10k-firmware to use the
firmware-5.bin_10.2.4-1.0-00033 firmware for the QCA9887.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>

firmware: ath10k-firmware: update QCA9888 firmware to 10.4-3.4-00104

This patch updates ath10k-firmware to use the
firmware-5.bin_10.4-3.4-00104 firmware for the QCA9888.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>

firmware: ath10k-firmware: update QCA9984 firmware to 10.4-3.4-00104

This patch updates ath10k-firmware to use the
firmware-5.bin_10.4-3.4-00104 firmware for the QCA9984.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>

firmware: ath10k-firmware: update QCA4019 firmware to 10.4-3.4-00104

This patch updates ath10k-firmware to use the
firmware-5.bin_10.4-3.4-00104 firmware for the QCA4019.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>

firmware: ath10k-firmware: update to 2017-12-20

This update automatically includes a new firmware for the QCA6174:
firmware-6.bin_WLAN.RM.4.4.1-00079-QCARMSWPZ-1

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>

odhcp6c: add sendopts config support and update to latest git HEAD

Add sendopts config support allowing to add options in sent DHCPv6 packets.

Options can be configured as follows :
uci set network.wan6.sendopts="sntpservers:3001:3001::1,3001:3001::2 11:00000000000000000000006674692F 0x3e8:ABCDEF"

Based on a patch by Frank Andrieu <fandrieu@gmail.com>

See https://git.openwrt.org/?p=project/odhcp6c.git;a=commit;h=510aaf6d528210c5e8a6159f9b80b32615e88c5f
for a more detailed description.

Latest git changes :
1f93bd4 dhcpv6: rework option passthrough logic
a477e95 odhcp6c: rework userclass and vendorclass command handling
510aaf6 odhcp6c: add -x opt:val support
ab75be1 treewide: update copyrights to 2018
f3a4609 odhcp6c: let odhcp6c_add_state return a success/failure indication

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>

ramips: tl-wr840n-v5: increase firmware partition for 4Mmtk layot

According to console log during TP-Link TL-WR840N v5 OEM firmware update
procedure 0x3e0000-0x3f0000 64kB "config" partition, which is used to store
router's configuration settings, is erased and recreated again during every
OEM firmware update procedure, thus does not contain any valuable factory data.
So it is conviniant to use this extra 64kB erase block for jffs overlay due
limited flash size on this device like it used on TP-Link's ar71xx boards.

Signed-off-by: Serg Studzinskii <serguzhg@gmail.com>

tools/mpfr: update to 4.0.0

Update mpfr to 4.0.0

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>

tools/mpc: Update to 1.1.0

Update mpc to 1.1.0

(note: adds compatibility with mpfr 4.0.0)

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>

util-linux: add fstrim support

This PR adds optional fstrim support

Signed-off-by: Dirk Brenken <dev@brenken.org>

kirkwood: fix sysupgrade

The platform_check_image() stub need to return 0 for success, otherwise
the sysupgrade will fail with:

Image check 'platform_check_image' failed.

Fixes: aa6f5f1787a6 ("kirkwood: use image metadata")
Signed-off-by: 尤晓杰 <yxj790222@163.com>
[reworded commit message}
Signed-off-by: Mathias Kresin <dev@kresin.me>

ipq806x: fix ZyXEL NBG6817 sysupgrade

Use the first found directory in the tar archive instead of relying on
a directory named according to the userspace boardname.

It allows to change the boardname without adding another compatibility
layer to the zyxel sysupgrade.

Fixes: 33f09cf15178 ("ipq806x: convert to dt-based board-detection")
Signed-off-by: Mathias Kresin <dev@kresin.me>

base-files: gpio switch: check if direction can be set

Obviously not all GPIO controller allow to change the direction. The issue
is around since the beginning of the script but only due to the recent
changes error messages are more visible.

Add a check if a change of the direction is supported by the GPIO
controller and fallback to setting only the value if not.

Fixes: FS#1271
Signed-off-by: Mathias Kresin <dev@kresin.me>

base-files: gpio switch: fix inverted logic

GPIOs are exported as active high to the sysfs, hence the logic need to be
inverted.

Fixes: e66c47fb14f5 ("base-files: gpio switch: set output value with
direction")
Signed-off-by: Mathias Kresin <dev@kresin.me>

ubox: update to latest git HEAD

e7a63fb ubox: Remove unnecessary memset calls

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>

ubus: fix wrong PKG_SOURCE_DATE

Fix wrong PKG_SOURCE_DATE introduced in e14cac0

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>

ubus: update to latest git HEAD

5bae22e ubus/lua: pass notification name to callback
212ceb1 valgrind complained about these
d57907c fix invalid close() call

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>

ath9k: discard undersized packets

Sometimes the hardware will push small packets that trigger a WARN_ON
in mac80211. Discard them early to avoid this issue.

Reported-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Felix Fietkau <nbd@nbd.name>

build: remove use of STAGING_DIR_HOST/usr (fixes cmake build error on macOS)

This directory is never created, nor is it used anywhere. Using it in
HOST_LDFLAGS causes a linker warning to be emitted on macOS, which
messes with cmake configure tests.

Signed-off-by: Felix Fietkau <nbd@nbd.name>

.gitignore: add .project & .cproject for eclipse users

For eclipse users, .project is always created inside the project.
For users of CDT within Eclipse, add also .cproject, thanks Dirk
Feytons.

Signed-off-by: Catrinel Catrinescu <cc@80211.de>

ar71xx: drop mdio-gpio.h include from mach-om5pacv2.c

The setup code of the OpenMesh OM5P ACv2 device uses nothing
from the mdio-gpio.h header, so remove the inclusion of that.

Also remove the kernel version check which is needed only
because the mdio-gpio.h header exists in a different path
in older kernels.

Compile tested only.

Cc: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>

cns3xxx: switch to kernel 4.14

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

cns3xxx: refresh patches

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

cns3xxx: remove deprecated uart flags

Flag UPF_NO_TXEN_TEST is deprecated.

Remove it.

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

cns3xxx: fix ethernet IRQ imbalance in 4.14

Kernel 4.14 contains more warnings regarding NAPI usage, which showed
following warning:

[ 4016.420000] ------------[ cut here ]------------
[ 4016.430000] WARNING: CPU: 1 PID: 14 at kernel/irq/manage.c:525
__enable_irq+0x3c/0x78
[ 4016.440000] Unbalanced enable for IRQ 51
[ 4016.440000] Modules linked in: ath9k ath9k_common pppoe ppp_async
ath9k_hw ath pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat
ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_nat
xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_TCPMSS
xt_REDIRECT xt_LOG slhc nf_reject_ipv4 nf_nat_redirs
[ 4016.500000] CPU: 1 PID: 14 Comm: ksoftirqd/1 Tainted: G        W
       4.14.11 #0
[ 4016.500000] Hardware name: Gateworks Corporation Laguna Platform
[ 4016.510000] Backtrace:
[ 4016.510000] [<c010a28c>] (dump_backtrace) from [<c010a56c>]
(show_stack+0x18/0x1c)
[ 4016.520000]  r7:c059df4b r6:00000000 r5:60000093 r4:00000000
[ 4016.530000] [<c010a554>] (show_stack) from [<c048b04c>]
(dump_stack+0x94/0xb4)
[ 4016.530000] [<c048afb8>] (dump_stack) from [<c011760c>]
(__warn+0xc8/0xf8)
[ 4016.540000]  r7:c059df4b r6:c015144c r5:00000000 r4:cf863e08
[ 4016.550000] [<c0117544>] (__warn) from [<c011767c>]
(warn_slowpath_fmt+0x40/0x48)
[ 4016.550000]  r9:cf863eb0 r8:00000036 r7:00000000 r6:c0636360
r5:00000033 r4:cf80a500
[ 4016.560000] [<c0117640>] (warn_slowpath_fmt) from [<c015144c>]
(__enable_irq+0x3c/0x78)
[ 4016.570000]  r3:00000033 r2:c059e0c5
[ 4016.570000] [<c0151410>] (__enable_irq) from [<c01514ec>]
(enable_irq+0x64/0x7c)
[ 4016.580000] [<c0151488>] (enable_irq) from [<c0335c14>]
(eth_poll+0x28c/0x558)
[ 4016.590000]  r5:d08926c0 r4:cf894488
[ 4016.590000] [<c0335988>] (eth_poll) from [<c03b1718>]
(net_rx_action+0xfc/0x2e8)
[ 4016.600000]  r10:cf863eb8 r9:cf863eb0 r8:00000001 r7:0f7b5000
r6:c0636360 r5:cfdeb360
[ 4016.610000]  r4:cf894488
[ 4016.610000] [<c03b161c>] (net_rx_action) from [<c0101510>]
(__do_softirq+0xe0/0x228)
[ 4016.620000]  r10:00000100 r9:c070204c r8:c0702040 r7:00000003
r6:00000008 r5:40000003
[ 4016.620000]  r4:cf862000
[ 4016.630000] [<c0101430>] (__do_softirq) from [<c011ae28>]
(run_ksoftirqd+0x34/0x58)
[ 4016.630000]  r10:c0133964 r9:00000000 r8:00000001 r7:00000000
r6:c070b44c r5:cf862000
[ 4016.640000]  r4:cf8037e0
[ 4016.640000] [<c011adf4>] (run_ksoftirqd) from [<c0133adc>]
(smpboot_thread_fn+0x178/0x190)
[ 4016.650000] [<c0133964>] (smpboot_thread_fn) from [<c013099c>]
(kthread+0x11c/0x138)
[ 4016.660000]  r9:cf8037e0 r8:cf802cdc r7:cf839df8 r6:cf803800
r5:00000000 r4:cf802cc0
[ 4016.670000] [<c0130880>] (kthread) from [<c0107218>]
(ret_from_fork+0x14/0x3c)
[ 4016.680000]  r10:00000000 r9:00000000 r8:00000000 r7:00000000
r6:00000000 r5:c0130880
[ 4016.680000]  r4:cf803800 r3:cf862000
[ 4016.690000] ---[ end trace 51114df08f429115 ]---

This is triggered by calling eth_schedule_poll(sw) after the IRQ has
been re-enabled.

Rework the network code to only enable IRQ's again if NAPI agrees it's
safe to do so.

Also only re-enable IRQ *after* cleaning up the RX ring and re-enabling
DMA, which otherwise resulted in ugly warnings regarding dirty page
fragments.
These popped up nearly immediately when building the kernel with O2 iso
Os.

--> Note that this change fixes stability issues, at the cost of ~8%
throughput performance.

While at it, also change the iface name being used in warning prints,
making it more obvious: "switch%d" --> "cns3xxx_eth"

The changes have been tested on 4 boards, each moving ~30TB of data

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

cns3xxx: update patches for 4.14

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

cns3xxx: refresh kernel 4.14 config

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

cns3xxx: copy patches for kernel 4.14

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

cns3xxx: copy config for kernel 4.14

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

config: don't define the same symbol twice

In commit fce35bce0f6e ("config: support new symbol intro'd in kernel
4.12")
I forgot to remove the initial debug test line.

This clearly is wrong as the same symbol is defined conditionally in the
line below as it should be.

I looked over it as I just checked if the symbol was present now upon
testing it.

Fixes: fce35bce0f6e ("config: support new symbol intro'd in kernel
4.12")

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

ar71xx: fix format of the 701-MIPS-ath79-add-routerboard-detection patches

Commit e15c63a37574 ("ar71xx: add support for MikroTik RouterBOARD wAP
G-5HacT2HnD (wAP AC") broke the format of the patches. In unified diff
format, the unchanged, contextual lines must be preceded by a space
character.

Refresh the patches with quilt to fix them.

Fixes: e15c63a37574 ("ar71xx: add support for MikroTik RouterBOARD wAPG-5HacT2HnD (wAP AC")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>

ar71xx: fix format of the 741-MIPS-ath79-add-PCI-for-QCA9556-SoC patches

The patches introduced in commit 20e68f6d395d ("ar71xx: kernel: enable
PCI on QCA9556 SoC") have non standard format. In unified diff format,
the unchanged, contextual lines must be preceded by a space character.

Refresh the patches with quilt to fix them.

Fixes: 20e68f6d395d ("ar71xx: kernel: enable PCI on QCA9556 SoC")
Signed-off-by: Gabor Juhos <juhosg@freemail.hu>

ar71xx: mach-rbspi: simplify reset button registration

The setup code defines four individual structures for the
Reset buttons of the supported boards. The only difference
between the definitions is the GPIO number used for the
button.

Replace the different structures with one generic variant,
and add a helper function to simplify the button registration.

Signed-off-by: Gabor Juhos <juhosg@freemail.hu>

imx6: add support for the intel gbit driver on GW5520

The Gateworks GW5520 board uses 2x intel gigabit mac's, instead of the
internal i.MX6 FEC.

Add support for these.

Signed-off-by: Scott V. Kamp <outbackdingo@gmail.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

mac80211: remove support code for authsae

Signed-off-by: Felix Fietkau <nbd@nbd.name>

authsae: remove package

It is no longer actively maintained and does not work well in many
configurations. Fully replaced by wpad-mesh

Signed-off-by: Felix Fietkau <nbd@nbd.name>

ipq8065: adjust SS USB PHY power settings

According to QSDK ipq8065 has different SS USB PHY power settings.

Adjust it according to QSDK settings.

It also corresponds to oem Netgear R7800 tarball for soc ver >= 2.
https://github.com/paul-chambers/netgear-r7800/blob/eeac2e10190f6f45e32e4c7012c4babc351898d8/git_home/linux.git/sourcecode/arch/arm/mach-msm/board-ipq806x.c#L2494

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>

ipq806x: usb: add phy 1 master reset control

In current state only phy 0 master reset is controlled.
Add the phy 1 reset.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>

ipq806x: usb: Control USB master reset

Picking commit from QSDK
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=eggplant&id=a86bda9f8a7965f0cedd347a9c04800eb9f41ea3

Commit message:
"During removal of the glue layer(dwc3-of-simple), USB master reset is set to active and during insertion it is de-activated."

Change-Id: I537dc810f6cb2a46664ee674840145066432b957
Signed-off-by: Vasudevan Murugesan <vmuruges@codeaurora.org>
(cherry picked from commit 4611e13580a216812f85f0801b95442d02eeb836)"

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>

ipq806x: dwc3: Fix power_on and power_off sequence

Picking commit from QSDK
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/drivers/phy/phy-qcom-dwc3.c?h=eggplant&id=d316437c9cdb70023a760342678f32e27241725a

The commit fixes:
- dwc3 phy module unloading
- possibly fixes FS#177 when some devices were improperly enumerated as HS while being SS thus stucking the driver during boot.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>

ipq806x: Update HSIO recommended usb phy settings

Picking commit from QSDK
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/drivers/phy/phy-qcom-dwc3.c?h=eggplant&id=cf82fdf4bdd081cd81bb081f7815b915bc8bb851

The comit adjusts USB dwc3 phy default values as per QSDK recomendation and allows to set it through DT.

Commit message:
"SoC version based values will be recovered from the device node.
If device node does not have such values, defaults are applied.

Change-Id: Ia77b5b7fe95ce1a433885df1761091bced98d989
Signed-off-by: Gokul Sriram Palanisamy <gpalan@codeaurora.org>"
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>

Revert "ipq8064: Fix dwc3 module unloading"

Preparing for proper fixes thus reverting commits:
- 8db079a9ff1756059250b801617a20baba214684 "ipq8064: Fix dwc3 module unloading"
- c75f059b0c4d09dd0da60e14c4933a9f645266d1 "ipq8064: Fix dwc3 module unloading"

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>

ipq806x: update clk and cpufreq drivers

A newer clk and cpufreq drivers for ipq806x platform had been sent upstream.

A change that i have noticed is that now it's possible to set min, cur and max frequencies from sysfs (previously it was bugged and caused nothing).

Following patches are removed:
- 0036-clk-Avoid-sending-high-rates-to-downstream-clocks-du.patch - seems it was dropped from the patchset by current committer.
- 0044-clk-qcom-krait-Remove-CLK_IS_ROOT.patch - already applied to the driver itself in the corresponding patch.
- 0057-clk-qcom-Add-regmap-mux-div-clocks-support.patch - seem to be irrelevant to ipq806x.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>

ipq806x: force 2nd pci slot into gen1 mode

According to QSDK and OEM tarballs (checked c2600, r7500v2, r7800) 2nd pci slot (pci1, 2,4 GHz card)) on ap148 based boards should operate in gen1 mode.
EA8500 is an exception and according to GPL pcie0 should operate in gen1 mode.

In previous commit we've added the support for this option, so enable it in DT for affected devices.

QSDK ref:
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=release/endive_preview_cc&id=f3b07fe309027c52fc163149500cedddd707c506

While at it move the phy transmit termination offset value into dtsi file as it's platform specific.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>

ipq806x: fix wireless regression

In current state there's huge regression on ipq806x target that causes the device to transmit broken/malformed frames that are not corrected/detected by error control mechanisms and other less severe issues.
https://bugs.lede-project.org/index.php?do=details&task_id=1197

This finally had been narrowed down to patch 0071-pcie-qcom-fixes.patch

Meanwhile QSDK contains a handful of commits that add support for ipq806x to upstream qcom pcie driver
https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/log/drivers/pci/host/pcie-qcom.c?h=eggplant
Unfortunately qca developers do not bother to push it upstream.

Using those commits instead of lede 0071 patch fixes mentioned issue and probably many others as it seems that corrupted data has been originating within pcie misconfiguration.

Fixes: FS#1197 and probably others
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>

tools/cmake: update to 3.10.1

Update cmake to 3.10.1
Refresh patches

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>

tools/scons: update to 3.0.1

Update scons to 3.0.1

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>

tools/libressl: update to 2.6.4

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>

xtables-addons: remove from base

The package has been moved to the package feed repository to allow for
non-base dependencies such as Perl.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>

netfilter: enable CONFIG_NF_CONNTRACK_MARK from kmod-nf-conntrack

Unconditionally enable connmark support and tie it to the conntrack core
module to allow removing this kernel configuration dependency from the
xtables-addons package.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>

feeds: switch git.lede-project.org URLs to git.openwrt.org

Signed-off-by: Jo-Philipp Wich <jo@mein.io>

iwinfo: update to latest git HEAD

5a5e21b nl80211: skip event notifications in wpa_supplicant scan result reply

Signed-off-by: Jo-Philipp Wich <jo@mein.io>

dnsmasq: use SIGINT for dnssec time valid

Dnsmasq used SIGHUP to do too many things: 1) set dnssec time validation
enabled, 2) bump SOA zone serial, 3) clear dns cache, 4) reload hosts
files, 5) reload resolvers/servers files.

Many subsystems within LEDE can send SIGHUP to dnsmasq: 1) ntpd hotplug
(to indicate time is valid for dnssec) 2) odhcpd (to indicate a
new/removed host - typically DHCPv6 leases) 3) procd on interface state
changes 4) procd on system config state changes, 5) service reload.

If dnssec time validation is enabled before the system clock has been
set to a sensible time, name resolution will fail.  Because name
resolution fails, ntpd is unable to resolve time server names to
addresses, so is unable to set time.  Classic chicken/egg.

Since commits 23bba9cb330cd298739a16e350b0029ed9429eef (service reload) &
4f02285d8b4a66359a8fa46f22a3efde391b5419 (system config)  make it more
likely a SIGHUP will be sent for events other than 'ntpd has set time'
it is more likely that an errant 'name resolution is failing for
everything' situation will be encountered.

Fortunately the upstream dnsmasq people agree and have moved 'check
dnssec timestamp enable' from SIGHUP handler to SIGINT.

Backport the upstream patch to use SIGINT.
ntpd hotplug script updated to use SIGINT.

Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>

ramips: use blue status LED for Xiaomi Router 3G

The blue LED is what other firmwares use for this device, and it's a lot
easier on the eyes than its shade of yellow, which implies an error
condition.

Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[merge into existing $boardname:blue:status block]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: Piotr Dymacz <pepe2k@gmail.com>
Acked-by: Cezary Jackiewicz <cezary@eko.one.pl>

ramips: add support for TP-Link Archer C20 v4

TP-Link Archer C20 v4 is a router with 5-port FE switch and
non-detachable antennas. It's based on MediaTek MT7628N+MT7610EN.

Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz and 1T1R 5 GHz
- 5x 10/100 Mbps Ethernet
- 3x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 7x LED (GPIO-controlled*), 2x button, power input switch

* WAN LED in this devices is a dual-color, dual-leads type which isn't
  (fully) supported by gpio-leds driver. This type of LED requires both
  GPIOs state change at the same time to select color or turn it off.
  For now, we support/use only the green part of the LED.
* MT7610EN ac chip isn't not supported by LEDE. Therefore 5Ghz won't
  work.

Flash instruction:

The only way to flash LEDE image in ArcherC20v4 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.66/24 and tftp server.
2. Rename "openwrt-ramips-mt7628-ArcherC20v4-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>

ramips: rename TP-Link Archer C20 to TP-Link Archer C20 v1

This changes device name from "TP-Link Archer C20" to "TP-Link Archer C20 v1"
because of TPLINK released new TP-Link Archer C20 v4. Additionally
migration to the generic board detection has been made.

Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>

ar71xx: fix TP-Link Archer C7 v4 switch LEDs

Match mapping of the switch LEDs according to the TP-Link
firmware behavior. LAN port 1 triggers the most right LAN LED,
LAN port 2 the second LAN LED from the right and so on.

Signed-off-by: David Bauer <mail@david-bauer.net>

ramips: add image checks

As long as we can't enforce image metadata, we need to use (platform)
image checks to have at least soem kind of validation.

Signed-off-by: Chen Minqiang <ptpt52@gmail.com>

ipq806x: drop ubifs support

Ubifs is disabled for all boards except the evaluation boards and the
Fritz!Box 4040 anyway. According the author, the ubifs support for the
Fritz!Box 4040 wasn't enabled on purpose.

Signed-off-by: Mathias Kresin <dev@kresin.me>

ipq806x: drop legacy image leftovers

Remove leftover code used for legacy images. There are no relevant
binary differences for the images after removing the legacy leftovers.

Signed-off-by: Mathias Kresin <dev@kresin.me>

ipq806x: unset filesystem specific build command by default

Initialise the filesystem specific build command. Otherwise it will be
unintended inherit to following images and will cause a wrong image
format.

The issue is around for ages but was only recently triggered due to the
added support for the Openmesh a42.

Fixes: FS#1276
Signed-off-by: Mathias Kresin <dev@kresin.me>

ipq806x: remove unnecessary filesystem specific build

The Openmesh factory image doesn't need a squashfs specific build command.

Signed-off-by: Mathias Kresin <dev@kresin.me>

ipq806x: use bin file extension for sysupgrade-tar images

Use the file extension bin for sysupgrade-tar images to unify the file
extension across the target/tree.

Signed-off-by: Mathias Kresin <dev@kresin.me>

uqmi: fix raw-ip mode for newer lte modems

Some newer LTE modems, like the MC7455 or EC25-E do not support
"802.3" mode, and will stay in "raw-ip" regardless of the mode being
set.

In this case, the driver must be informed that it should handle all
packets in raw mode. [1]

This commit fixes connectivity issues for these devices.

Before:

[ Node 5 ] udhcpc -i wwan0
udhcpc: started, v1.27.2
udhcpc: sending discover
udhcpc: sending discover
udhcpc: sending discover

After:

[ Node 5 ] udhcpc -i wwan0
udhcpc: started, v1.27.2
udhcpc: sending discover
udhcpc: sending select for 100.66.245.226
udhcpc: lease of 100.66.245.226 obtained, lease time 7200
udhcpc: ifconfig wwan0 100.66.245.226 netmask 255.255.255.252 broadcast
+
udhcpc: setting default routers: 100.66.245.225

[1] https://lists.freedesktop.org/archives/libqmi-
devel/2017-January/002064.html

Tested on cns3xxx using a Sierra Wireless MC7455 LTE-A

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
[bumped PKG_RELEASE]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>

ar71xx: image: rework EnGenius ENS202EXT factory image

Current EnGenius ENS202EXT factory image recipe version causes factory
images of the following devices to be corrupted. This issue wasn't
visible until recent changes of image Makefile snippets order.

Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

tools: make-ext4fs: remove LEDE_GIT references

Change the make-ext4fs Makefile to use the common PROJECT_GIT
variable instead.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>

omap24xx: remove referece to not existing kmod-usb-musb-tusb6010

Remove leftover reference to a not existing kmod-usb-musb-tusb6010 from
the omap24xx target, the corresponding module is built into the kernel.

Fixes: 96815fe0a2 ("kernel: remove omap24xx specific kernel module packages")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>

6rd: pass ipcalc as argument to eval

Instead of grepping for NETWORK after calling ipcalc.sh; pass ipcalc.sh as
argument to eval allowing to use $NETWORK to retrieve the IPv4 prefix
(ip4prefix).

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>

ar71xx: add support for MikroTik RouterBOARD wAP G-5HacT2HnD (wAP AC)

This patch adds support for the MikroTik RouterBOARD wAP G-5HacT2HnD (wAP
AC), a small weatherproof dual band, dual-radio 802.11ac wireless AP with
integrated omnidirectional anntennae and one 10/100/1000 Mbps Ethernet
ports.

See https://mikrotik.com/product/RBwAPG-5HacT2HnD for more info.

Specifications:
- SoC: Qualcomm Atheros QCA9556
- RAM: 64 MB
- Storage: 16 MB NOR
- Wireless:
   · Atheros AR9550 (SoC) 802.11b/g/n 2x2:2, 2 dBi antennae
   · Qualcomm QCA9880 802.11a/n/ac 3x3:3, 2 dBi antennae
- Ethernet: Atheros AG71xx (SoC, AR8033), 1x 1000/100/10 port, passive
   PoE in

Working:
- Board/system detection
- Sysupgrade
- Serial console
- Ethernet
- 2.4 GHz radio
- 5 GHz radio
- Reset button

Not working:
- LEDs (added according to Mikrotik's GPL sources but not functional)

Unsupported:
- ZT2046Q SPI temperature and voltage sensor

Contributors: Giuseppe Tipaldi (@Ciusss89)
              Ricky (@rickydee)

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[daniel@makrotopia.org: whitespace fix, use PHYADDR instead of PHYMASK]

ar71xx: kernel: enable PCI on QCA9556 SoC

This patch enables the PCI bus on the QCA9556 SoC, the same way it is
done on the same family SoC QCA9558.

Tested on a MikroTik RouterBoard wAPG-5HacT2HnD (wAP AC).

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>

ramips: add support for ALFA Network AC1200RM

ALFA Network AC1200RM is an AC1200 router, with 5-port FE switch and
USB 2.0 port. Device is based on MediaTek MT7620A + MT7612EN.

Specification:

- MT7620A (580 MHz)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 5x 10/100 Mbps Ethernet with passive PoE output in WAN and LAN4
- 2T2R 2.4 GHz (MT7620A)
- 2T2R 5 GHz (MT7612EN)
- 1x USB 2.0
- 9x LED (8 driven by GPIO)
- 1x button (reset)
- DC jack for main power input (12-24 V)
- 2x UART, I2C, I2S and LED headers

Flash instruction (do it under U-Boot, using UART and TFTP server):

Select option "2: Load system code then write to Flash via TFTP" and
use "sysupgrade" image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

uboot-envtools: add support for GL.iNet GL-AR750

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

ar71xx: add support for GL.iNet GL-AR750

GL.iNet GL-AR750 is a small size, dual-band (AC750) router, based on
Qualcomm/Atheros QCA9531 v2 + QCA9887. FCC ID: 2AFIW-AR750.

Specification:

- 650/597/216 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3x 10/100 Mbps Ethernet
- 2T2R 2.4 GHz (QCA9531)
- 1T1R 5 GHz (QCA9887)
- 1x USB 2.0 (power controlled by GPIO)
- 1x microSD (GL857L)
- 3x LED (all driven by GPIO)
- 1x button (reset)
- 1x 2-pos switch
- header for optional PoE module
- 1x micro USB for main power input
- UART + I2C header on PCB

Flash instruction:

Vendor firmware is based on OpenWrt/LEDE. GUI or sysupgrade can be used
to flash OpenWrt/LEDE firmware.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

ar71xx: image: move Sitecom WLR-8100 from legacy to generic

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

ar71xx: fix Sitecom WLR-8100 support

This patch fixes Sitecom WLR-8100:

- mtd layout
- LAN and WAN MAC address setup
- 2.4 GHz Wi-Fi MAC address setup
- 5 GHz Wi-Fi support (calibration data, MAC address setup, missing
ath10k-* packages)

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[squashed commits, fixed whitespace issues, reworded commit message]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

uboot-envtools: add support for ALFA Network R36A

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

ar71xx: add support for ALFA Network R36A

ALFA Network R36A is a successor of the previous model, the R36 (Ralink
RT3050F based). New version is based on Qualcomm/Atheros QCA9531 v2.

Specification:

- 650/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R (QCA9531) 2.4 GHz, 2x u.fl connectors on PCB
- 1x USB 2.0 (power controlled by GPIO)
- 6x LED (5 of them are driven by GPIO)
- 2x button (reset, wifi/wps)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- DC jack for main power input (12 V)
- UART header on PCB

Flash instruction:

You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
device, wait for first blink of all LEDs (indicates network setup),
then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

ar71xx: add support for Teltonika RUT900

Teltonika RUT900 is an industrial 3G router based on Atheros AR9344.

There are available 3 other models in RUT9xx series: RUT905, RUT950 and
RUT955, which differ in availability of additional I/O ports, built-in
GSM modem type, GPS antenna and other features. FCC ID of the RUT950
model (LTE module built-in): 2AET4-RUT950.

This patch adds support for the RUT900 model only but can be easily
extended to cover whole series. Also, as there are several different
3/4G modules (Huawei, Quectel, Telit) used in whole series, packages
required for WWAN support are not included by default. It is up to the
user to install required software for built-in modem.

Specification:

- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344), with ext. PA (MGA-22103) and LNA
- built-in 3G module (example: Telit HE910-D)
- 2x miniSIM slot
- 2x RP-SMA/F (Wi-Fi), 2x SMA/F (3G)
- PCA9539 16-bit GPIO I2C expander
- 12x LED (4 are driven by AR9344, 7 by PCA9539)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- UART available on PCB edge connector

Serial console pinout:

- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side

Flash instruction:

Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.03.960" firmware and U-Boot "3.0.1".

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

uboot-envtools: add support for ALFA Network N5Q

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

ar71xx: add support for ALFA Network N5Q

ALFA Network N5Q is a successor of previous model, the N5 (outdoor
CPE/AP, based on Atheros AR7240 + AR9280). New version is based on
Atheros AR9344.

Specification:

- 550/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R 5 GHz (AR9344), with ext. PA (RFPA5542) and LNA, up to 27 dBm
- 8x LED (7 are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- header for optional 802.3at/af PoE module
- DC jack for main power input (optional, not installed by default)
- UART header on PCB

Flash instruction:

You can use sysupgrade image directly in vendor firmare which is based
on OpenWrt/LEDE. Alternatively, you can use web recovery mode in U-Boot:

1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with one of RJ45 ports, press the reset button, power up
device, wait for first blink of all LEDs (indicates network setup),
then keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

uboot-envtools: add support for ALFA Network AP91-5G

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

ar71xx: add support for ALFA Network AP91-5G

ALFA Network AP91-5G is a 5 GHz outdoor AP/CPE board, based on Atheros
AR7240 + AR9280.

Specification:

- 400/400/200 MHz (CPU/DDR/AHB)
- 32 MB of RAM (DDR1)
- 8 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 1T1R 5 GHz (AR9280), with ext. PA (SE5004L) and LNA, up to 27 dBm
- 6x LED (5 are driven by GPIO)
- 1x button (reset)
- external h/w watchdog (EM6324QYSP5B, disabled and not used)
- header for optional 802.3at/af PoE module
- DC jack for main power input (optional, not installed by default)
- UART and LEDs headers on PCB

Flash instruction:

Use "factory" image in vendor GUI (in case of problems, make sure your
board has up to date firmware). Alternatively, TFTP in U-Boot can be
used: select option "2. Load system code then write to Flash via TFTP"
during early boot and use "sysupgrade" image.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

ar71xx: base-files: cosmetic cleanups in preinit scripts

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

ar71xx: base-files: drop LED control from 05_set_iface_mac_ar71xx

There is no "dir-615-c1:green:wancpu" LED defined in mach-dir-615-c1.c

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

ar71xx: base-files: fix boards order in 05_set_preinit_iface_ar71xx

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>

kernel: add missing config symbol

The KEXEC_FILE symbol exists for X86 since kernel 3.17, and since 4.10
for PPC64. Add it to x86/config-4.9 and to generic/config-4.14.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>