Florian Fainelli [Tue, 25 Apr 2017 18:33:03 +0000 (11:33 -0700)]
dt-bindings: mdio: Clarify binding document
The described GPIO reset property is applicable to *all* child PHYs. If
we have one reset line per PHY present on the MDIO bus, these
automatically become properties of the child PHY nodes.
Finally, indicate how the RESET pulse width must be defined, which is
the maximum value of all individual PHYs RESET pulse widths determined
by reading their datasheets.
Fixes: 69226896ad63 ("mdio_bus: Issue GPIO RESET to PHYs.")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 26 Apr 2017 18:44:39 +0000 (14:44 -0400)]
Merge branch 'tcp-do-not-use-tcp_time_stamp-for-rcv-autotuning'
Eric Dumazet says:
====================
tcp: do not use tcp_time_stamp for rcv autotuning
Some devices or linux distributions use HZ=100 or HZ=250
TCP receive buffer autotuning has poor behavior caused by this choice.
Since autotuning happens after 4 ms or 10 ms, short distance flows
get their receive buffer tuned to a very high value, but after an initial
period where it was frozen to (too small) initial value.
With BBR (or other CC allowing to increase BDP), we are willing to
increase tcp_rmem[2], but this receive autotuning defect is a blocker
for hosts dealing with gazillions of TCP flows in the data centers,
since many of them have inflated RCVBUF. Risk of OOM is too high.
Note that TSO autodefer, tcp cubic, and TCP TS options (RFC 7323)
also suffer from our dependency to jiffies (via tcp_time_stamp).
We have ongoing efforts to improve all that in the future.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 25 Apr 2017 17:15:41 +0000 (10:15 -0700)]
tcp: switch rcv_rtt_est and rcvq_space to high resolution timestamps
Some devices or distributions use HZ=100 or HZ=250
TCP receive buffer autotuning has poor behavior caused by this choice.
Since autotuning happens after 4 ms or 10 ms, short distance flows
get their receive buffer tuned to a very high value, but after an initial
period where it was frozen to (too small) initial value.
With tp->tcp_mstamp introduction, we can switch to high resolution
timestamps almost for free (at the expense of 8 additional bytes per
TCP structure)
Note that some TCP stacks use usec TCP timestamps where this
patch makes even more sense : Many TCP flows have < 500 usec RTT.
Hopefully this finer TS option can be standardized soon.
Tested:
HZ=100 kernel
./netperf -H lpaa24 -t TCP_RR -l 1000 -- -r 10000,10000 &
Peer without patch :
lpaa24:~# ss -tmi dst lpaa23
...
skmem:(r0,rb8388608,...)
rcv_rtt:10 rcv_space:
3210000 minrtt:0.017
Peer with the patch :
lpaa23:~# ss -tmi dst lpaa24
...
skmem:(r0,rb428800,...)
rcv_rtt:0.069 rcv_space:30000 minrtt:0.017
We can see saner RCVBUF, and more precise rcv_rtt information.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 25 Apr 2017 17:15:40 +0000 (10:15 -0700)]
tcp: remove ack_time from struct tcp_sacktag_state
It is no longer needed, everything uses tp->tcp_mstamp instead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 25 Apr 2017 17:15:39 +0000 (10:15 -0700)]
tcp: use tp->tcp_mstamp in tcp_clean_rtx_queue()
Following patch will remove ack_time from struct tcp_sacktag_state
Same info is now found in tp->tcp_mstamp
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 25 Apr 2017 17:15:38 +0000 (10:15 -0700)]
tcp: do not pass timestamp to tcp_rack_advance()
No longer needed, since tp->tcp_mstamp holds the information.
This is needed to remove sack_state.ack_time in a following patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 25 Apr 2017 17:15:37 +0000 (10:15 -0700)]
tcp: do not pass timestamp to tcp_rate_gen()
No longer needed, since tp->tcp_mstamp holds the information.
This is needed to remove sack_state.ack_time in a following patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 25 Apr 2017 17:15:36 +0000 (10:15 -0700)]
tcp: do not pass timestamp to tcp_fastretrans_alert()
Not used anymore now tp->tcp_mstamp holds the information.
This is needed to remove sack_state.ack_time in a following patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 25 Apr 2017 17:15:35 +0000 (10:15 -0700)]
tcp: do not pass timestamp to tcp_rack_identify_loss()
Not used anymore now tp->tcp_mstamp holds the information.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 25 Apr 2017 17:15:34 +0000 (10:15 -0700)]
tcp: do not pass timestamp to tcp_rack_mark_lost()
This is no longer used, since tcp_rack_detect_loss() takes
the timestamp from tp->tcp_mstamp
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 25 Apr 2017 17:15:33 +0000 (10:15 -0700)]
tcp: do not pass timestamp to tcp_rack_detect_loss()
We can use tp->tcp_mstamp as it contains a recent timestamp.
This removes a call to skb_mstamp_get() from tcp_rack_reo_timeout()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 25 Apr 2017 17:15:32 +0000 (10:15 -0700)]
tcp: add tp->tcp_mstamp field
We want to use precise timestamps in TCP stack, but we do not
want to call possibly expensive kernel time services too often.
tp->tcp_mstamp is guaranteed to be updated once per incoming packet.
We will use it in the following patches, removing specific
skb_mstamp_get() calls, and removing ack_time from
struct tcp_sacktag_state.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Tue, 25 Apr 2017 09:41:34 +0000 (11:41 +0200)]
rhashtable: remove insecure_max_entries param
no users in the tree, insecure_max_entries is always set to
ht->p.max_size * 2 in rhtashtable_init().
Replace only spot that uses it with a ht->p.max_size check.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 25 Apr 2017 18:36:52 +0000 (11:36 -0700)]
net: move xdp_prog field in RX cache lines
(struct net_device, xdp_prog) field should be moved in RX cache lines,
reducing latencies when a single packet is received on idle host,
since netif_elide_gro() needs it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Tue, 25 Apr 2017 11:36:50 +0000 (11:36 +0000)]
drivers: net: xgene-v2: Fix error return code in xge_mdio_config()
Fix to return error code -ENODEV from the no PHY found error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 18 Apr 2017 19:36:58 +0000 (15:36 -0400)]
net: Generic XDP
This provides a generic SKB based non-optimized XDP path which is used
if either the driver lacks a specific XDP implementation, or the user
requests it via a new IFLA_XDP_FLAGS value named XDP_FLAGS_SKB_MODE.
It is arguable that perhaps I should have required something like
this as part of the initial XDP feature merge.
I believe this is critical for two reasons:
1) Accessibility. More people can play with XDP with less
dependencies. Yes I know we have XDP support in virtio_net, but
that just creates another depedency for learning how to use this
facility.
I wrote this to make life easier for the XDP newbies.
2) As a model for what the expected semantics are. If there is a pure
generic core implementation, it serves as a semantic example for
driver folks adding XDP support.
One thing I have not tried to address here is the issue of
XDP_PACKET_HEADROOM, thanks to Daniel for spotting that. It seems
incredibly expensive to do a skb_cow(skb, XDP_PACKET_HEADROOM) or
whatever even if the XDP program doesn't try to push headers at all.
I think we really need the verifier to somehow propagate whether
certain XDP helpers are used or not.
v5:
- Handle both negative and positive offset after running prog
- Fix mac length in XDP_TX case (Alexei)
- Use rcu_dereference_protected() in free_netdev (kbuild test robot)
v4:
- Fix MAC header adjustmnet before calling prog (David Ahern)
- Disable LRO when generic XDP is installed (Michael Chan)
- Bypass qdisc et al. on XDP_TX and record the event (Alexei)
- Do not perform generic XDP on reinjected packets (DaveM)
v3:
- Make sure XDP program sees packet at MAC header, push back MAC
header if we do XDP_TX. (Alexei)
- Elide GRO when generic XDP is in use. (Alexei)
- Add XDP_FLAG_SKB_MODE flag which the user can use to request generic
XDP even if the driver has an XDP implementation. (Alexei)
- Report whether SKB mode is in use in rtnl_xdp_fill() via XDP_FLAGS
attribute. (Daniel)
v2:
- Add some "fall through" comments in switch statements based
upon feedback from Andrew Lunn
- Use RCU for generic xdp_prog, thanks to Johannes Berg.
Tested-by: Andy Gospodarek <andy@greyhouse.net>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Tue, 25 Apr 2017 07:07:18 +0000 (07:07 +0000)]
qed: fix invalid use of sizeof in qed_alloc_qm_data()
sizeof() when applied to a pointer typed expression gives the
size of the pointer, not that of the pointed data.
Fixes: b5a9ee7cf3be ("qed: Revise QM configuration")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Teng Qin [Tue, 25 Apr 2017 02:00:37 +0000 (19:00 -0700)]
bpf: map_get_next_key to return first key on NULL
When iterating through a map, we need to find a key that does not exist
in the map so map_get_next_key will give us the first key of the map.
This often requires a lot of guessing in production systems.
This patch makes map_get_next_key return the first key when the key
pointer in the parameter is NULL.
Signed-off-by: Teng Qin <qinteng@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Maloney [Tue, 25 Apr 2017 01:29:11 +0000 (21:29 -0400)]
selftests/net: Fix broken test case in psock_fanout
The error return falue form sock_fanout_open is -1, not zero. One test
case was checking for 0 instead of -1.
Tested: Built and tested in clean client.
Signed-off-by: Mike Maloney <maloney@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Khoronzhuk [Mon, 24 Apr 2017 20:54:06 +0000 (23:54 +0300)]
net: ethernet: ti: netcp_core: remove unused compl queue mapping
This code is unused and probably was unintentionally left while
moving completion queue mapping in submit function.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 25 Apr 2017 15:49:33 +0000 (11:49 -0400)]
Merge branch 'qed-vf-tunnel'
Manish Chopra says:
====================
qed/qede: VF tunnelling support
With this series VFs can run vxlan/geneve/gre tunnels over it.
Please consider applying this series to "net-next"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Chopra, Manish [Mon, 24 Apr 2017 17:00:49 +0000 (10:00 -0700)]
qed - VF tunnelling support [VXLAN/GENEVE/GRE]
This patch adds hardware channel APIs support between
VF and PF for tunnelling configuration for the VFs.
According to that configuration VFs can run VXLAN/GENEVE/GRE
tunnels over it with tunnel features offloaded.
Using these APIs VF can also request for UDP ports configuration
to the PF, although PF and it's child VFs share the same port.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chopra, Manish [Mon, 24 Apr 2017 17:00:48 +0000 (10:00 -0700)]
qed/qede: Add UDP ports in bulletin board
This patch adds support for UDP ports in bulletin board
to notify UDP ports change to the VFs
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chopra, Manish [Mon, 24 Apr 2017 17:00:47 +0000 (10:00 -0700)]
qede: Configure UDP ports in local context.
This patch configures UDP ports locally instead of
configuring them in deferred context which would be
helpful in synchronizing UDP ports configuration for VFs
which will be enabled in further patches.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chopra, Manish [Mon, 24 Apr 2017 17:00:46 +0000 (10:00 -0700)]
qede: Disable tunnel offloads for non offloaded UDP ports
This patch disables tunnel offloads via ndo_features_check()
if given UDP port is not offloaded to hardware. This in turn
allows to run multiple tunnel interfaces using different UDP ports.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chopra, Manish [Mon, 24 Apr 2017 17:00:45 +0000 (10:00 -0700)]
qed/qede: Enable tunnel offloads based on hw configuration
This patch enables tunnel feature offloads based on hw configuration
at initialization time instead of enabling them always.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chopra, Manish [Mon, 24 Apr 2017 17:00:44 +0000 (10:00 -0700)]
qed: refactor tunnelling - API/Structs
This patch changes the tunnel APIs to use per tunnel
info instead of using bitmasks for all tunnels and also
uses single struct to hold the data to prepare multiple
variant of tunnel configuration ramrods to be sent to the hardware.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 25 Apr 2017 15:41:57 +0000 (11:41 -0400)]
Merge branch 'l2tpeth-info'
Guillaume Nault says:
====================
l2tp: add informations about l2tpeth interfaces in /sys
Patch #1 lets userspace retrieve the naming scheme of an l2tpeth
interface, using /sys/class/net/<iface>/name_assign_type.
Patch #2 adds the DEVTYPE field in /sys/class/net/<iface>/uevent so
that userspace can reliably know if a device is an l2tpeth interface.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Mon, 24 Apr 2017 12:16:07 +0000 (14:16 +0200)]
l2tp: define "l2tpeth" device type
Export type of l2tpeth interfaces to userspace
(/sys/class/net/<iface>/uevent).
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Acked-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Mon, 24 Apr 2017 12:16:06 +0000 (14:16 +0200)]
l2tp: set name_assign_type for devices created by l2tp_eth.c
Export naming scheme used when creating l2tpeth interfaces
(/sys/class/net/<iface>/name_assign_type). This let userspace know if
the device's name has been generated automatically or defined manually.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Acked-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jamal Hadi Salim [Sun, 23 Apr 2017 17:17:28 +0000 (13:17 -0400)]
net sched actions: Complete the JUMPX opcode
per discussion at netconf/netdev:
When we have an action that is capable of branching (example a policer),
we can achieve a continuation of the action graph by programming a
"continue" where we find an exact replica of the same filter rule with a lower
priority and the remainder of the action graph. When you have 100s of thousands
of filters which require such a feature it gets very inefficient to do two
lookups.
This patch completes a leftover feature of action codes. Its time has come.
Example below where a user labels packets with a different skbmark on ingress
of a port depending on whether they have/not exceeded the configured rate.
This mark is then used to make further decisions on some egress port.
#rate control, very low so we can easily see the effect
sudo $TC actions add action police rate 1kbit burst 90k \
conform-exceed pipe/jump 2 index 10
# skbedit index 11 will be used if the user conforms
sudo $TC actions add action skbedit mark 11 ok index 11
# skbedit index 12 will be used if the user does not conform
sudo $TC actions add action skbedit mark 12 ok index 12
#lets bind the user ..
sudo $TC filter add dev $ETH parent ffff: protocol ip prio 8 u32 \
match ip dst 127.0.0.8/32 flowid 1:10 \
action police index 10 \
action skbedit index 11 \
action skbedit index 12
#run a ping -f and see what happens..
#
jhs@foobar:~$ sudo $TC -s filter ls dev $ETH parent ffff: protocol ip
filter pref 8 u32
filter pref 8 u32 fh 800: ht divisor 1
filter pref 8 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:10 (rule hit 2800 success 1005)
match
7f000008/
ffffffff at 16 (success 1005 )
action order 1: police 0xa rate 1Kbit burst 23440b mtu 2Kb action pipe/jump 2 overhead 0b
ref 2 bind 1 installed 207 sec used 122 sec
Action statistics:
Sent 84420 bytes 1005 pkt (dropped 0, overlimits 721 requeues 0)
backlog 0b 0p requeues 0
action order 2: skbedit mark 11 pass
index 11 ref 2 bind 1 installed 204 sec used 122 sec
Action statistics:
Sent 60564 bytes 721 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
action order 3: skbedit mark 12 pass
index 12 ref 2 bind 1 installed 201 sec used 122 sec
Action statistics:
Sent 23856 bytes 284 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
Not bad, about 28% non-conforming packets..
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 25 Apr 2017 14:52:47 +0000 (10:52 -0400)]
Merge tag 'linux-can-next-for-4.12-
20170425' of git://git./linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2017-04-25
this is a pull request of 21 patches for net-next/master.
There are 4 patches by Stephane Grosjean for the PEAK PCAN-PCIe FD
CAN-FD boards. The next 7 patches are by Mario Huettel, which add
support for M_CAN IP version >= v3.1.x to the m_can driver. A patch by
Remigiusz Kołłątaj adds support for the Microchip CAN BUS Analyzer. 8
patches by Oliver Hartkopp complete the initial CAN network namespace
support. Wei Yongjun's patch for the ti_hecc driver fixes the return
value check in the probe function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Thu, 20 Apr 2017 16:08:15 +0000 (18:08 +0200)]
ipvlan: use pernet operations and restrict l3s hooks to master netns
commit
4fbae7d83c98c30efc ("ipvlan: Introduce l3s mode") added
registration of netfilter hooks via nf_register_hooks().
This API provides the illusion of 'global' netfilter hooks by placing the
hooks in all current and future network namespaces.
In case of ipvlan the hook appears to be only needed in the namespace
that contains the ipvlan master device (i.e., usually init_net), so
placing them in all namespaces is not needed.
This switches ipvlan driver to pernet operations, and then only registers
hooks in namespaces where a ipvlan master device is set to l3s mode.
Extra care has to be taken when the master device is moved to another
namespace, as we might have to 'move' the netfilter hooks too.
This is done by storing the namespace the ipvlan port was created in.
On REGISTER event, do (un)register operations in the old/new namespaces.
This will also allow removal of the nf_register_hooks() in a future patch.
Cc: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Tue, 25 Apr 2017 06:44:05 +0000 (06:44 +0000)]
can: ti_hecc: fix return value check in ti_hecc_probe()
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Fixes: dabf54dd1c63 ("can: ti_hecc: Convert TI HECC driver to DT only driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Oliver Hartkopp [Tue, 25 Apr 2017 06:19:45 +0000 (08:19 +0200)]
can: enable module auto loading for virtual CAN interfaces
Autoload the vcan module when a vcan instance is to be created by
'ip link add type vcan'
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Oliver Hartkopp [Tue, 25 Apr 2017 06:19:44 +0000 (08:19 +0200)]
can: add Virtual CAN Tunnel driver (vxcan)
Similar to the virtual ethernet driver veth, vxcan implements a
local CAN traffic tunnel between two virtual CAN network devices.
See Kconfig entry for details.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Oliver Hartkopp [Tue, 25 Apr 2017 06:19:43 +0000 (08:19 +0200)]
can: network namespace support for CAN gateway
The CAN gateway was not implemented as per-net in the initial network
namespace support by Mario Kicherer (
8e8cda6d737d).
This patch enables the CAN gateway to be used in different namespaces.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Oliver Hartkopp [Tue, 25 Apr 2017 06:19:42 +0000 (08:19 +0200)]
can: network namespace support for CAN_BCM protocol
The CAN_BCM protocol and its procfs entries were not implemented as per-net
in the initial network namespace support by Mario Kicherer (
8e8cda6d737d).
This patch adds the missing per-net functionality for the CAN BCM.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Oliver Hartkopp [Tue, 25 Apr 2017 06:19:41 +0000 (08:19 +0200)]
can: complete initial namespace support
The statistics and its proc output was not implemented as per-net in the
initial network namespace support by Mario Kicherer (
8e8cda6d737d).
This patch adds the missing per-net statistics for the CAN subsystem.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Oliver Hartkopp [Tue, 25 Apr 2017 06:19:40 +0000 (08:19 +0200)]
can: remove obsolete definitions
can_rx_alldev_list is a per-net data structure now. Remove it's definition
here and can_rx_dev_list too.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Oliver Hartkopp [Tue, 25 Apr 2017 06:19:39 +0000 (08:19 +0200)]
can: remove obsolete pernet_operations definitions
The namespace support for the CAN subsystem does not need any additional
memory. So when ".size = 0" there's no extra memory allocated by the system.
And therefore ".id" is obsolete too.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Oliver Hartkopp [Tue, 25 Apr 2017 06:19:38 +0000 (08:19 +0200)]
can: fix memory leak in initial namespace support
The can_rx_alldev_list is a per-net data structure now and allocated in
can_pernet_init(). Make sure the memory is free'd in can_pernet_exit() too.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Remigiusz Kołłątaj [Fri, 14 Apr 2017 18:32:28 +0000 (20:32 +0200)]
can: mcba_usb: Add support for Microchip CAN BUS Analyzer
SocketCAN driver for Microchip CAN BUS Analyzer
(http://www.microchip.com/development-tools/)
Changes in v4:
- possible memory leak fixed in mcba_usb_write_bulk_callback
- LED support added
- failure handling in mcba_usb_probe improved
- C99 initializers for structs on stack
Changes in v3:
- improved/simplified CAN ID conversion
- functions for transmission of skb and cmd separated
- fixed/improved netif_stop_queue handling
- style/cosmetic corrections
Changes in v2:
- Termination handling reimplemented to fit new netlink API
(IFLA_CAN_TERMINATION)
- Bitrate handling reimplemented to fit new netlink API
(IFLA_CAN_BITRATE)
- CAN ID conversion refactored (changed from macro to inline functions)
- CAN DLC handling using get_can_dlc()
- Endianness handling for can_speed introduced
- Debugging removed
- Redundant error prints removed
- Style/cosmetic corrections (i.e. macro names, redefs, inits etc.)
Signed-off-by: Remigiusz Kołłątaj <remigiusz.kollataj@mobica.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Mario Huettel [Sat, 8 Apr 2017 12:10:15 +0000 (14:10 +0200)]
can: m_can: Enable TX FIFO Handling for M_CAN IP version >= v3.1.x
* Added defines for TX Event FIFO Element
* Adapted ndo_start_xmit function.
For versions >= v3.1.x it uses the TX FIFO to optimize the data
throughput. It stores the echo skb at the same index as in the
M_CAN's TX FIFO. The frame's message marker is set to this index.
This message marker is received in the TX Event FIFO after
the message was successfully transmitted. It is used to echo the
correct echo skb back to the network stack.
* Added m_can_echo_tx_event function. It reads all received
message markers in the TX Event FIFO and loops back the
corresponding echo skbs.
* ISR checks for new TX Event Entry interrupt for version >= 3.1.x.
Signed-off-by: Mario Huettel <mario.huettel@gmx.net>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Mario Huettel [Sat, 8 Apr 2017 12:10:14 +0000 (14:10 +0200)]
can: m_can: Configuration for TX and TX event FIFOs
* TX/TX Event FIFO sizes are configured for version >= v3.1.x
Signed-off-by: Mario Huettel <mario.huettel@gmx.net>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Mario Huettel [Sat, 8 Apr 2017 12:10:13 +0000 (14:10 +0200)]
can: m_can: Enable M_CAN version dependent initialization
This patch adapts the initialization of the M_CAN. So it can be used
with all versions >= 3.0.x.
Changes:
* Added version element to m_can_priv structure to hold M_CAN version.
* Renamed bittiming structs for version 3.0.x
* Added new bittiming structs for version >= 3.1.x
* Function alloc_m_can_dev takes 2 new arguments. The TX FIFO size and the
base address of the module.
* Chip configuration for CAN_CTRLMODE_LOOPBACK is changed: Enabled
CCCR_MON bit. In combination with TEST_LBCK it activates the internal
loopback mode. Leaving CCCR_MON '0' results in external loopback mode.
* Clocks are temporarily enabled by platform_propbe function in order to
allow read access to the Core Release register and the Control Register.
Registers are used to detect M_CAN version and optional Non-ISO Feature.
Initialization of M_CAN for version >= 3.1.x:
* TX FIFO of M_CAN is used to transmit frames. The driver does not need to
stop the tx queue after each frame sent.
* Initialization of TX Event FIFO is added.
* NON-ISO is fixed for all M_CAN versions < 3.2.x. Version 3.2.x _can_ have
the NISO (Non-ISO) bit which can switch the mode of the M_CAN to Non-ISO
mode. This bit does not have to be writeable. Therefore it is checked.
If it is writable Non-ISO support is added to the controllers supported
CAN modes.
New Functions:
* Function to check the Core Release version. The read value determines the
behaviour of the driver.
* Function to check if the NISO bit for version >= 3.2.x is implemented.
Signed-off-by: Mario Huettel <mario.huettel@gmx.net>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Mario Huettel [Sat, 8 Apr 2017 12:10:12 +0000 (14:10 +0200)]
can: m_can: Updated register defines to newest version
* Updated register defines to newest M_CAN version (v3.2.1).
* Changed defines in the whole code.
Signed-off-by: Mario Huettel <mario.huettel@gmx.net>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Mario Huettel [Sat, 8 Apr 2017 12:10:11 +0000 (14:10 +0200)]
can: m_can: Removed virtual address from print
The virtual address of the device was printed. I removed it because it
leaks internal information.
Signed-off-by: Mario Huettel <mario.huettel@gmx.net>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Mario Huettel [Sat, 8 Apr 2017 12:10:10 +0000 (14:10 +0200)]
can: m_can: Removed initialization of FIFO water marks
FIFO water marks disabled because the driver doesn't handle water mark
events.
Signed-off-by: Mario Huettel <mario.huettel@gmx.net>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Mario Huettel [Sat, 8 Apr 2017 12:10:09 +0000 (14:10 +0200)]
can: m_can: Disabled Interrupt Line 1
* Disabled interrupt line 1. The driver didn't use it.
Signed-off-by: Mario Huettel <mario.huettel@gmx.net>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Stephane Grosjean [Thu, 19 Jan 2017 15:31:07 +0000 (16:31 +0100)]
can: peak: add support for PEAK PCAN-PCIe FD CAN-FD boards
This patch adds the support of the PCAN-PCI Express FD boards made
by PEAK-System, for computers using the PCI Express slot.
The PCAN-PCI Express FD has one or two CAN FD channels, depending
on the model. A galvanic isolation of the CAN ports protects
the electronics of the card and the respective computer against
disturbances of up to 500 Volts. The PCAN-PCI Express FD can be operated
with ambient temperatures in a range of -40 to +85 °C.
Such boards run an extented version of the CAN-FD IP running into USB
CAN-FD interfaces from PEAK-System, so this patch adds several new commands
and their corresponding data types to the PEAK CAN-FD common definitions
header file too.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Stephane Grosjean [Thu, 19 Jan 2017 15:31:06 +0000 (16:31 +0100)]
can: peak: move header file to new can common subdir
The CAN-FD IP from PEAK-System runs into several kinds of PC CAN-FD
interfaces. Up to now, only the USB CAN-FD adapters were supported by
the Kernel. In order to prepare the adding of some new non-USB CAN-FD
interfaces, this patch moves - and rename - the IP definitions file
from its private (usb) sub-directory into a - newly created - CAN specific
one.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Stephane Grosjean [Thu, 19 Jan 2017 15:31:05 +0000 (16:31 +0100)]
can: peak: fix usage of const qualifier in pointers args
Fixes the usage of the const qualifier in the memory pointer arguments
of the declared inline functions. By changing the line containing "const",
this patch also changes the name of the arg into a more usual one.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Stephane Grosjean [Thu, 19 Jan 2017 15:31:04 +0000 (16:31 +0100)]
can: peak: fix usage of usb specific data type
This patch fixes the wrong usage of a specific USB data type into a common
header file. This common header file is intended to define the common data
types and values that define access to the PEAK-System CAN-FD IP, whatever
the PC interface is.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
David S. Miller [Tue, 25 Apr 2017 03:55:20 +0000 (23:55 -0400)]
Merge branch 'virtio-net-tx-napi'
Willem de Bruijn says:
====================
virtio-net tx napi
Add napi for virtio-net transmit completion processing.
Changes:
v2 -> v3:
- convert __netif_tx_trylock to __netif_tx_lock on tx napi poll
ensure that the handler always cleans, to avoid deadlock
- unconditionally clean in start_xmit
avoid adding an unnecessary "if (use_napi)" branch
- remove virtqueue_disable_cb in patch 5/5
a noop in the common event_idx based loop
- document affinity_hint_set constraint
v1 -> v2:
- disable by default
- disable unless affinity_hint_set
because cache misses add up to a third higher cycle cost,
e.g., in TCP_RR tests. This is not limited to the patch
that enables tx completion cleaning in rx napi.
- use trylock to avoid contention between tx and rx napi
- keep interrupts masked during xmit_more (new patch 5/5)
this improves cycles especially for multi UDP_STREAM, which
does not benefit from cleaning tx completions on rx napi.
- move free_old_xmit_skbs (new patch 3/5)
to avoid forward declaration
not changed:
- deduplicate virnet_poll_tx and virtnet_poll_txclean
they look similar, but have differ too much to make it
worthwhile.
- delay netif_wake_subqueue for more than 2 + MAX_SKB_FRAGS
evaluated, but made no difference
- patch 1/5
RFC -> v1:
- dropped vhost interrupt moderation patch:
not needed and likely expensive at light load
- remove tx napi weight
- always clean all tx completions
- use boolean to toggle tx-napi, instead
- only clean tx in rx if tx-napi is enabled
- then clean tx before rx
- fix: add missing braces in virtnet_freeze_down
- testing: add 4KB TCP_RR + UDP test results
Based on previous patchsets by Jason Wang:
[RFC V7 PATCH 0/7] enable tx interrupts for virtio-net
http://lkml.iu.edu/hypermail/linux/kernel/1505.3/00245.html
Before commit
b0c39dbdc204 ("virtio_net: don't free buffers in xmit
ring") the virtio-net driver would free transmitted packets on
transmission of new packets in ndo_start_xmit and, to catch the edge
case when no new packet is sent, also in a timer at 10HZ.
A timer can cause long stalls. VIRTIO_F_NOTIFY_ON_EMPTY avoids stalls
due to low free descriptor count. It does not address a stalls due to
low socket SO_SNDBUF. Increasing timer frequency decreases that stall
time, but increases interrupt rate and, thus, cycle count.
Currently, with no timer, packets are freed only at ndo_start_xmit.
Latency of consume_skb is now unbounded. To avoid a deadlock if a sock
reaches SO_SNDBUF, packets are orphaned on tx. This breaks TCP small
queues.
Reenable TCP small queues by removing the orphan. Instead of using a
timer, convert the driver to regular tx napi. This does not have the
unresolved stall issue and does not have any frequency to tune.
By keeping interrupts enabled by default, napi increases tx
interrupt rate. VIRTIO_F_EVENT_IDX avoids sending an interrupt if
one is already unacknowledged, so makes this more feasible today.
Combine that with an optimization that brings interrupt rate
back in line with the existing version for most workloads:
Tx completion cleaning on rx interrupts elides most explicit tx
interrupts by relying on the fact that many rx interrupts fire.
Tested by running {1, 10, 100} {TCP, UDP} STREAM, RR, 4K_RR benchmarks
from a guest to a server on the host, on an x86_64 Haswell. The guest
runs 4 vCPUs pinned to 4 cores. vhost and the test server are
pinned to a core each.
All results are the median of 5 runs, with variance well < 10%.
Used neper (github.com/google/neper) as test process.
Napi increases single stream throughput, but increases cycle cost.
The optimizations bring this down. The previous patchset saw a
regression with UDP_STREAM, which does not benefit from cleaning tx
interrupts in rx napi. This regression is now gone for 10x, 100x.
Remaining difference is higher 1x TCP_STREAM, lower 1x UDP_STREAM.
The latest results are with process, rx napi and tx napi affine to
the same core. All numbers are lower than the previous patchset.
upstream napi
TCP_STREAM:
1x:
Mbps 27816 39805
Gcycles 274 285
10x:
Mbps 42947 42531
Gcycles 300 296
100x:
Mbps 31830 28042
Gcycles 279 269
TCP_RR Latency (us):
1x:
p50 21 21
p99 27 27
Gcycles 180 167
10x:
p50 40 39
p99 52 52
Gcycles 214 211
100x:
p50 281 241
p99 411 337
Gcycles 218 226
TCP_RR 4K:
1x:
p50 28 29
p99 34 36
Gcycles 177 167
10x:
p50 70 71
p99 85 134
Gcycles 213 214
100x:
p50 442 611
p99 802 785
Gcycles 237 216
UDP_STREAM:
1x:
Mbps 29468 26800
Gcycles 284 293
10x:
Mbps 29891 29978
Gcycles 285 312
100x:
Mbps 30269 30304
Gcycles 318 316
UDP_RR:
1x:
p50 19 19
p99 23 23
Gcycles 180 173
10x:
p50 35 40
p99 54 64
Gcycles 245 237
100x:
p50 234 286
p99 484 473
Gcycles 224 214
Note that GSO is enabled, so 4K RR still translates to one packet
per request.
Lower throughput at 100x vs 10x can be (at least in part)
explained by looking at bytes per packet sent (nstat). It likely
also explains the lower throughput of 1x for some variants.
upstream:
N=1 bytes/pkt=16581
N=10 bytes/pkt=61513
N=100 bytes/pkt=51558
at_rx:
N=1 bytes/pkt=65204
N=10 bytes/pkt=65148
N=100 bytes/pkt=56840
====================
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Willem de Bruijn [Mon, 24 Apr 2017 17:49:30 +0000 (13:49 -0400)]
virtio-net: keep tx interrupts disabled unless kick
Tx napi mode increases the rate of transmit interrupts. Suppress some
by masking interrupts while more packets are expected. The interrupts
will be reenabled before the last packet is sent.
This optimization reduces the througput drop with tx napi for
unidirectional flows such as UDP_STREAM that do not benefit from
cleaning tx completions in the the receive napi handler.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Mon, 24 Apr 2017 17:49:29 +0000 (13:49 -0400)]
virtio-net: clean tx descriptors from rx napi
Amortize the cost of virtual interrupts by doing both rx and tx work
on reception of a receive interrupt if tx napi is enabled. With
VIRTIO_F_EVENT_IDX, this suppresses most explicit tx completion
interrupts for bidirectional workloads.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Mon, 24 Apr 2017 17:49:28 +0000 (13:49 -0400)]
virtio-net: move free_old_xmit_skbs
An upcoming patch will call free_old_xmit_skbs indirectly from
virtnet_poll. Move the function above this to avoid having to
introduce a forward declaration.
This is a pure move: no code changes.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Mon, 24 Apr 2017 17:49:27 +0000 (13:49 -0400)]
virtio-net: transmit napi
Convert virtio-net to a standard napi tx completion path. This enables
better TCP pacing using TCP small queues and increases single stream
throughput.
The virtio-net driver currently cleans tx descriptors on transmission
of new packets in ndo_start_xmit. Latency depends on new traffic, so
is unbounded. To avoid deadlock when a socket reaches its snd limit,
packets are orphaned on tranmission. This breaks socket backpressure,
including TSQ.
Napi increases the number of interrupts generated compared to the
current model, which keeps interrupts disabled as long as the ring
has enough free descriptors. Keep tx napi optional and disabled for
now. Follow-on patches will reduce the interrupt cost.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Mon, 24 Apr 2017 17:49:26 +0000 (13:49 -0400)]
virtio-net: napi helper functions
Prepare virtio-net for tx napi by converting existing napi code to
use helper functions. This also deduplicates some logic.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 25 Apr 2017 02:42:34 +0000 (19:42 -0700)]
sparc64: Improve 64-bit constant loading in eBPF JIT.
Doing a full 64-bit decomposition is really stupid especially for
simple values like 0 and -1.
But if we are going to optimize this, go all the way and try for all 2
and 3 instruction sequences not requiring a temporary register as
well.
First we do the easy cases where it's a zero or sign extended 32-bit
number (sethi+or, sethi+xor, respectively).
Then we try to find a range of set bits we can load simply then shift
up into place, in various ways.
Then we try negating the constant and see if we can do a simple
sequence using that with a xor at the end. (f.e. the range of set
bits can't be loaded simply, but for the negated value it can)
The final optimized strategy involves 4 instructions sequences not
needing a temporary register.
Otherwise we sadly fully decompose using a temp..
Example, from ALU64_XOR_K: 0x0000ffffffff0000 ^ 0x0 = 0x0000ffffffff0000:
0000000000000000 <foo>:
0: 9d e3 bf 50 save %sp, -176, %sp
4: 01 00 00 00 nop
8: 90 10 00 18 mov %i0, %o0
c: 13 3f ff ff sethi %hi(0xfffffc00), %o1
10: 92 12 63 ff or %o1, 0x3ff, %o1 !
ffffffff <foo+0xffffffff>
14: 93 2a 70 10 sllx %o1, 0x10, %o1
18: 15 3f ff ff sethi %hi(0xfffffc00), %o2
1c: 94 12 a3 ff or %o2, 0x3ff, %o2 !
ffffffff <foo+0xffffffff>
20: 95 2a b0 10 sllx %o2, 0x10, %o2
24: 92 1a 60 00 xor %o1, 0, %o1
28: 12 e2 40 8a cxbe %o1, %o2, 38 <foo+0x38>
2c: 9a 10 20 02 mov 2, %o5
30: 10 60 00 03 b,pn %xcc, 3c <foo+0x3c>
34: 01 00 00 00 nop
38: 9a 10 20 01 mov 1, %o5 ! 1 <foo+0x1>
3c: 81 c7 e0 08 ret
40: 91 eb 40 00 restore %o5, %g0, %o0
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 24 Apr 2017 22:56:21 +0000 (15:56 -0700)]
sparc64: Support cbcond instructions in eBPF JIT.
cbcond combines a compare with a branch into a single instruction.
The limitations are:
1) Only newer chips support it
2) For immediate compares we are limited to 5-bit signed immediate
values
3) The branch displacement is limited to 10-bit signed
4) We cannot use it for JSET
Also, cbcond (unlike all other sparc control transfers) lacks a delay
slot.
Currently we don't have a useful instruction we can push into the
delay slot of normal branches. So using cbcond pretty much always
increases code density, and is therefore a win.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 24 Apr 2017 20:20:20 +0000 (16:20 -0400)]
Merge branch 'bpf-misc-cleanups'
Alexander Alemayhu says:
====================
Misc BPF cleanup
while looking into making the Makefile in samples/bpf better handle O= I saw
several warnings when running `make clean && make samples/bpf/`. This series
reduces those warnings.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Alemayhu [Mon, 24 Apr 2017 13:31:08 +0000 (15:31 +0200)]
samples/bpf: check before defining offsetof
Fixes the following warning
samples/bpf/test_lru_dist.c:28:0: warning: "offsetof" redefined
#define offsetof(TYPE, MEMBER) ((size_t)&((TYPE *)0)->MEMBER)
In file included from ./tools/lib/bpf/bpf.h:25:0,
from samples/bpf/libbpf.h:5,
from samples/bpf/test_lru_dist.c:24:
/usr/lib/gcc/x86_64-redhat-linux/6.3.1/include/stddef.h:417:0: note: this is the location of the previous definition
#define offsetof(TYPE, MEMBER) __builtin_offsetof (TYPE, MEMBER)
Signed-off-by: Alexander Alemayhu <alexander@alemayhu.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Alemayhu [Mon, 24 Apr 2017 13:31:07 +0000 (15:31 +0200)]
samples/bpf: add static to function with no prototype
Fixes the following warning
samples/bpf/cookie_uid_helper_example.c: At top level:
samples/bpf/cookie_uid_helper_example.c:276:6: warning: no previous prototype for ‘finish’ [-Wmissing-prototypes]
void finish(int ret)
^~~~~~
HOSTLD samples/bpf/per_socket_stats_example
Signed-off-by: Alexander Alemayhu <alexander@alemayhu.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Alemayhu [Mon, 24 Apr 2017 13:31:06 +0000 (15:31 +0200)]
samples/bpf: add -Wno-unknown-warning-option to clang
I was initially going to remove '-Wno-address-of-packed-member' because I
thought it was not supposed to be there but Daniel suggested using
'-Wno-unknown-warning-option'.
This silences several warnings similiar to the one below
warning: unknown warning option '-Wno-address-of-packed-member' [-Wunknown-warning-option]
1 warning generated.
clang -nostdinc -isystem /usr/lib/gcc/x86_64-redhat-linux/6.3.1/include -I./arch/x86/include -I./arch/x86/include/generated/uapi -I./arch/x86/include/generated -I./include
-I./arch/x86/include/uapi -I./include/uapi -I./include/generated/uapi -include ./include/linux/kconfig.h \
-D__KERNEL__ -D__ASM_SYSREG_H -Wno-unused-value -Wno-pointer-sign \
-Wno-compare-distinct-pointer-types \
-Wno-gnu-variable-sized-type-not-at-end \
-Wno-address-of-packed-member -Wno-tautological-compare \
-O2 -emit-llvm -c samples/bpf/xdp_tx_iptunnel_kern.c -o -| llc -march=bpf -filetype=obj -o samples/bpf/xdp_tx_iptunnel_kern.o
$ clang --version
clang version 3.9.1 (tags/RELEASE_391/final)
Target: x86_64-unknown-linux-gnu
Thread model: posix
InstalledDir: /usr/bin
Signed-off-by: Alexander Alemayhu <alexander@alemayhu.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Mon, 24 Apr 2017 20:14:35 +0000 (22:14 +0200)]
bpf: make bpf_xdp_adjust_head support mandatory
Now that also the last in-tree user of the xdp_adjust_head bit has
been removed, we can remove the flag from struct bpf_prog altogether.
This, at the same time, also makes sure that any future driver for
XDP comes with bpf_xdp_adjust_head() support right away.
A rejection based on this flag would also mean that tail calls
couldn't be used with such driver as per
c2002f983767 ("bpf: fix
checking xdp_adjust_head on tail calls") fix, thus lets not allow
for it in the first place.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pan Bian [Sun, 23 Apr 2017 12:04:04 +0000 (20:04 +0800)]
qlcnic: fix unchecked return value
Function pci_find_ext_capability() may return 0, which is an invalid
address. In function qlcnic_sriov_virtid_fn(), its return value is used
without validation. This may result in invalid memory access bugs. This
patch fixes the bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pan Bian [Sun, 23 Apr 2017 09:38:35 +0000 (17:38 +0800)]
wan: pc300too: abort path on failure
In function pc300_pci_init_one(), on the ioremap error path, function
pc300_pci_remove_one() is called to free the allocated memory. However,
the path is not terminated, and the freed memory will be used later,
resulting in use-after-free bugs. This path fixes the bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pan Bian [Sun, 23 Apr 2017 07:09:19 +0000 (15:09 +0800)]
tipc: check return value of nlmsg_new
Function nlmsg_new() will return a NULL pointer if there is no enough
memory, and its return value should be checked before it is used.
However, in function tipc_nl_node_get_monitor(), the validation of the
return value of function nlmsg_new() is missed. This patch fixes the
bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pan Bian [Sun, 23 Apr 2017 06:28:37 +0000 (14:28 +0800)]
lwtunnel: check return value of nla_nest_start
Function nla_nest_start() may return a NULL pointer on error. However,
in function lwtunnel_fill_encap(), the return value of nla_nest_start()
is not validated before it is used. This patch checks the return value
of nla_nest_start() against NULL.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 24 Apr 2017 18:35:45 +0000 (14:35 -0400)]
Merge branch 'nfp-dma-adjust_head-fixes'
Jakub Kicinski says:
====================
nfp: DMA flags, adjust head and fixes
This series takes advantage of Alex's DMA_ATTR_SKIP_CPU_SYNC to make
XDP packet modifications "correct" from DMA API point of view. It
also allows us to parse the metadata before we run XDP at no additional
DMA sync cost. That way we can get rid of the metadata memcpy, and
remove the last upstream user of bpf_prog->xdp_adjust_head.
David's patch adds a way to read capabilities from the management
firmware.
There are also two net-next fixes. Patch 4 which fixes what seems to
be a result of a botched rebase on my part. Patch 5 corrects locking
when state of ethernet ports is being refreshed.
v3: move the sync from alloc func to the actual give to hw func
v2: sync rx buffers before giving them to the card (Alex)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Sun, 23 Apr 2017 03:17:56 +0000 (20:17 -0700)]
nfp: remove the refresh of all ports optimization
The code refreshing the eth port state was trying to update state
of all ports of the card. Unfortunately to safely walk the port
list we would have to hold the port lock, which we can't due to
lock ordering constraints against rtnl.
Make the per-port sync refresh and async refresh of all ports
completely separate routines.
Fixes: 172f638c93dd ("nfp: add port state refresh")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Sun, 23 Apr 2017 03:17:55 +0000 (20:17 -0700)]
nfp: fix free list buffer size reporting
XDP headroom should not be included in free list buffer size.
Fixes: 6fe0c3b43804 ("nfp: add support for xdp_adjust_head()")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Brunecz [Sun, 23 Apr 2017 03:17:54 +0000 (20:17 -0700)]
nfp: add NSP routine to get static information
Retrieve identifying information from the NSP. For now it only
contains versions of firmware subcomponents.
Signed-off-by: David Brunecz <david.brunecz@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Sun, 23 Apr 2017 03:17:53 +0000 (20:17 -0700)]
nfp: parse metadata prepend before XDP runs
Calling memcpy to shift metadata out of the way for XDP to run
seems like an overkill. The most common metadata contents are
8 bytes containing type and flow hash. Simply parse the metadata
before we run XDP.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Sun, 23 Apr 2017 03:17:52 +0000 (20:17 -0700)]
nfp: make use of the DMA_ATTR_SKIP_CPU_SYNC attr
DMA unmap may destroy changes CPU made to the buffer. To make XDP
run correctly on non-x86 platforms we should use the
DMA_ATTR_SKIP_CPU_SYNC attribute.
Thanks to using the attribute we can now push the sync operation to the
common code path from XDP handler.
A little bit of variable name reshuffling is required to bring the
code back to readable state.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 24 Apr 2017 18:30:47 +0000 (14:30 -0400)]
Merge branch 'cls_flower-MPLS'
Benjamin LaHaise says:
====================
flower: add MPLS matching support
This patch series adds support for parsing MPLS flows in the flow dissector
and the flower classifier. Each of the MPLS TTL, BOS, TC and Label fields
can be used for matching.
v2: incorporate style feedback, move #defines to linux/include/mpls.h
Note: this omits Jiri's request to remove tabs between the type and
field names in struct declarations. This would be inconsistent with
numerous other struct definitions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin LaHaise [Sat, 22 Apr 2017 20:52:47 +0000 (16:52 -0400)]
cls_flower: add support for matching MPLS fields (v2)
Add support to the tc flower classifier to match based on fields in MPLS
labels (TTL, Bottom of Stack, TC field, Label).
Signed-off-by: Benjamin LaHaise <benjamin.lahaise@netronome.com>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Simon Horman <simon.horman@netronome.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Hadar Hen Zion <hadarh@mellanox.com>
Cc: Gao Feng <fgao@ikuai8.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin LaHaise [Sat, 22 Apr 2017 20:52:46 +0000 (16:52 -0400)]
flow_dissector: add mpls support (v2)
Add support for parsing MPLS flows to the flow dissector in preparation for
adding MPLS match support to cls_flower.
Signed-off-by: Benjamin LaHaise <benjamin.lahaise@netronome.com>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Simon Horman <simon.horman@netronome.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Eric Dumazet <jhs@mojatatu.com>
Cc: Hadar Hen Zion <hadarh@mellanox.com>
Cc: Gao Feng <fgao@ikuai8.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 24 Apr 2017 18:27:18 +0000 (14:27 -0400)]
Merge branch 'tcp-fastopen-middlebox-fixes'
Wei Wang says:
====================
net/tcp_fastopen: Fix for various TFO firewall issues
Currently there are still some firewall issues in the middlebox
which make the middlebox drop packets silently for TFO sockets.
This kind of issue is hard to be detected by the end client.
This patch series tries to detect such issues in the kernel and disable
TFO temporarily.
More details about the issues and the fixes are included in the following
patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Wang [Thu, 20 Apr 2017 21:45:48 +0000 (14:45 -0700)]
net/tcp_fastopen: Remove mss check in tcp_write_timeout()
Christoph Paasch from Apple found another firewall issue for TFO:
After successful 3WHS using TFO, server and client starts to exchange
data. Afterwards, a 10s idle time occurs on this connection. After that,
firewall starts to drop every packet on this connection.
The fix for this issue is to extend existing firewall blackhole detection
logic in tcp_write_timeout() by removing the mss check.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Wang [Thu, 20 Apr 2017 21:45:47 +0000 (14:45 -0700)]
net/tcp_fastopen: Add snmp counter for blackhole detection
This counter records the number of times the firewall blackhole issue is
detected and active TFO is disabled.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Wang [Thu, 20 Apr 2017 21:45:46 +0000 (14:45 -0700)]
net/tcp_fastopen: Disable active side TFO in certain scenarios
Middlebox firewall issues can potentially cause server's data being
blackholed after a successful 3WHS using TFO. Following are the related
reports from Apple:
https://www.nanog.org/sites/default/files/Paasch_Network_Support.pdf
Slide 31 identifies an issue where the client ACK to the server's data
sent during a TFO'd handshake is dropped.
C ---> syn-data ---> S
C <--- syn/ack ----- S
C (accept & write)
C <---- data ------- S
C ----- ACK -> X S
[retry and timeout]
https://www.ietf.org/proceedings/94/slides/slides-94-tcpm-13.pdf
Slide 5 shows a similar situation that the server's data gets dropped
after 3WHS.
C ---- syn-data ---> S
C <--- syn/ack ----- S
C ---- ack --------> S
S (accept & write)
C? X <- data ------ S
[retry and timeout]
This is the worst failure b/c the client can not detect such behavior to
mitigate the situation (such as disabling TFO). Failing to proceed, the
application (e.g., SSL library) may simply timeout and retry with TFO
again, and the process repeats indefinitely.
The proposed solution is to disable active TFO globally under the
following circumstances:
1. client side TFO socket detects out of order FIN
2. client side TFO socket receives out of order RST
We disable active side TFO globally for 1hr at first. Then if it
happens again, we disable it for 2h, then 4h, 8h, ...
And we reset the timeout to 1hr if a client side TFO sockets not opened
on loopback has successfully received data segs from server.
And we examine this condition during close().
The rational behind it is that when such firewall issue happens,
application running on the client should eventually close the socket as
it is not able to get the data it is expecting. Or application running
on the server should close the socket as it is not able to receive any
response from client.
In both cases, out of order FIN or RST will get received on the client
given that the firewall will not block them as no data are in those
frames.
And we want to disable active TFO globally as it helps if the middle box
is very close to the client and most of the connections are likely to
fail.
Also, add a debug sysctl:
tcp_fastopen_blackhole_detect_timeout_sec:
the initial timeout to use when firewall blackhole issue happens.
This can be set and read.
When setting it to 0, it means to disable the active disable logic.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 24 Apr 2017 18:11:10 +0000 (14:11 -0400)]
Merge tag 'mlx5-updates-2017-04-22' of git://git./linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2017-04-22
Sparse and compiler warnings fixes from Stephen Hemminger.
From Roi Dayan and Or Gerlitz, Add devlink and mlx5 support for controlling
E-Switch encapsulation mode, this knob will enable HW support for applying
encapsulation/decapsulation to VF traffic as part of SRIOV e-switch offloading.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Sat, 22 Apr 2017 16:33:16 +0000 (09:33 -0700)]
net: add rcu locking when changing early demux
systemd-sysctl is triggering a suspicious RCU usage message when
net.ipv4.tcp_early_demux or net.ipv4.udp_early_demux is changed via
a sysctl config file:
[ 33.896184] ===============================
[ 33.899558] [ ERR: suspicious RCU usage. ]
[ 33.900624] 4.11.0-rc7+ #104 Not tainted
[ 33.901698] -------------------------------
[ 33.903059] /home/dsa/kernel-2.git/net/ipv4/sysctl_net_ipv4.c:305 suspicious rcu_dereference_check() usage!
[ 33.905724]
other info that might help us debug this:
[ 33.907656]
rcu_scheduler_active = 2, debug_locks = 0
[ 33.909288] 1 lock held by systemd-sysctl/143:
[ 33.910373] #0: (sb_writers#5){.+.+.+}, at: [<
ffffffff8123a370>] file_start_write+0x45/0x48
[ 33.912407]
stack backtrace:
[ 33.914018] CPU: 0 PID: 143 Comm: systemd-sysctl Not tainted 4.11.0-rc7+ #104
[ 33.915631] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
[ 33.917870] Call Trace:
[ 33.918431] dump_stack+0x81/0xb6
[ 33.919241] lockdep_rcu_suspicious+0x10f/0x118
[ 33.920263] proc_configure_early_demux+0x65/0x10a
[ 33.921391] proc_udp_early_demux+0x3a/0x41
add rcu locking to proc_configure_early_demux.
Fixes: dddb64bcb3461 ("net: Add sysctl to toggle early demux for tcp and udp")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 24 Apr 2017 18:05:40 +0000 (14:05 -0400)]
Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2017-04-22
Here are some more Bluetooth patches (and one 802.15.4 patch) in the
bluetooth-next tree targeting the 4.12 kernel. Most of them are pure
fixes.
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Sat, 22 Apr 2017 12:22:01 +0000 (13:22 +0100)]
net: netcp: fix spelling mistake: "memomry" -> "memory"
Trivial fix to spelling mistake in dev_err message and rejoin
line.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geliang Tang [Sat, 22 Apr 2017 01:21:10 +0000 (09:21 +0800)]
net: atheros: atl1: use offset_in_page() macro
Use offset_in_page() macro instead of open-coding.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 24 Apr 2017 17:54:48 +0000 (13:54 -0400)]
Merge branch 'bnxt_en-misc-next'
Michael Chan says:
====================
bnxt_en: Updates for net-next.
Miscellaneous updates include passing DCBX RoCE VLAN priority to firmware,
checking one more new firmware flag before allowing DCBX to run on the host,
adding 100Gbps speed support, adding check to disallow speed settings on
Multi-host NICs, and a minor fix for reporting VF attributes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Deepak Khungar [Sat, 22 Apr 2017 00:11:26 +0000 (20:11 -0400)]
bnxt_en: Restrict a PF in Multi-Host mode from changing port PHY configuration
This change restricts the PF in multi-host mode from setting any port
level PHY configuration. The settings are controlled by firmware in
Multi-Host mode.
Signed-off-by: Deepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sat, 22 Apr 2017 00:11:25 +0000 (20:11 -0400)]
bnxt_en: Check the FW_LLDP_AGENT flag before allowing DCBX host agent.
Check the additional flag in bnxt_hwrm_func_qcfg() before allowing
DCBX to be done in host mode.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Deepak Khungar [Sat, 22 Apr 2017 00:11:24 +0000 (20:11 -0400)]
bnxt_en: Add 100G link speed reporting for BCM57454 ASIC in ethtool
Added support for 100G link speed reporting for Broadcom BCM57454
ASIC in ethtool command.
Signed-off-by: Deepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sat, 22 Apr 2017 00:11:23 +0000 (20:11 -0400)]
bnxt_en: Fix VF attributes reporting.
The .ndo_get_vf_config() is returning the wrong qos attribute. Fix
the code that checks and reports the qos and spoofchk attributes. The
BNXT_VF_QOS and BNXT_VF_LINK_UP flags should not be set by default
during init. time.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sat, 22 Apr 2017 00:11:22 +0000 (20:11 -0400)]
bnxt_en: Pass DCB RoCE app priority to firmware.
When the driver gets the RoCE app priority set/delete call through DCBNL,
the driver will send the information to the firmware to set up the
priority VLAN tag for RDMA traffic.
[ New version using the common ETH_P_IBOE constant in if_ether.h ]
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jarno Rajahalme [Fri, 21 Apr 2017 23:48:06 +0000 (16:48 -0700)]
openvswitch: Add eventmask support to CT action.
Add a new optional conntrack action attribute OVS_CT_ATTR_EVENTMASK,
which can be used in conjunction with the commit flag
(OVS_CT_ATTR_COMMIT) to set the mask of bits specifying which
conntrack events (IPCT_*) should be delivered via the Netfilter
netlink multicast groups. Default behavior depends on the system
configuration, but typically a lot of events are delivered. This can be
very chatty for the NFNLGRP_CONNTRACK_UPDATE group, even if only some
types of events are of interest.
Netfilter core init_conntrack() adds the event cache extension, so we
only need to set the ctmask value. However, if the system is
configured without support for events, the setting will be skipped due
to extension not being found.
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jarno Rajahalme [Fri, 21 Apr 2017 23:48:05 +0000 (16:48 -0700)]
openvswitch: Typo fix.
Fix typo in a comment.
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Acked-by: Greg Rose <gvrose8192@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 24 Apr 2017 16:52:15 +0000 (12:52 -0400)]
Merge branch 'ibmvnic-updates-and-fixes'
Nathan Fontenot says:
====================
ibmvnic: Additional updates and bug fixes
This set of patches is an additional set of updates and bug fixes to
the ibmvnic driver which applies on top of the previous set of updates
sent out on 4/19.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon [Fri, 21 Apr 2017 19:39:16 +0000 (15:39 -0400)]
ibmvnic: Free skb's in cases of failure in transmit
When an error is encountered during transmit we need to free the
skb instead of returning TX_BUSY.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nathan Fontenot [Fri, 21 Apr 2017 19:39:10 +0000 (15:39 -0400)]
ibmvnic: Validate napi exist before disabling them
Validate that the napi structs exist before trying to disable them
at driver close.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>