ASoC: da7210: Add support for line out and DAC

DA7210 has three line outputs. OUT1 Left, OUT1 Right and OUT2 (mono).
This patch adds support for gain controls for these three line outs.
It also adds support for overall DAC gain control.

Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: da7210: Add support for DAPM

This patch adds support for DAPM covering all inputs and outputs
as well as ADC and DAC.

Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Use SGTL5000_LINREG_VDDD_MASK instead of hardcoded mask value

We have defined SGTL5000_LINREG_VDDD_MASK in sgtl5000.h,
use it instead of hardcoded (0x1 << 4) - 1 for the mask.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Set sgtl5000->ldo in ldo_regulator_register

Otherwise calling ldo_regulator_remove() does not unregister regulator
and free memories.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8996: Use SND_SOC_DAPM_AIF_OUT for AIF2 Capture

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

ASoC: wm8994: Use SND_SOC_DAPM_AIF_OUT for AIF3 Capture

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

ASoC: rt5631: Remove unused codec field from struct rt5631_priv

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: ak4671: Use snd_soc_update_bits for read-modify-write

Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Fix reg_word_size for ak4104

According to the register map in datasheet, the registers are 8 bit.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm9081: Fix setting soft VMID ramp enable with VMID 2*240k

According to the datasheet:
BIT 2:1
        VMID_SEL[1:0] VMID Divider Enable and Select
        00 = VMID disabled
        01 = 2x40k Omh divider
        10 = 2x240k Omh divider
        11 = 2x5k Omh divider

To set VMID 2*240k, we should OR reg with 0x04 instead of 0x40.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: ak4641: Use SND_SOC_DAPM_DAC for Voice Playback stream widget

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: da7210: Add support for ALC and Noise suppression

This patch adds controls to set following ALC parameters,
 - Max gain, Min gain, Noise gain, Attack rate, Release rate and delay

It also adds a switch to enable/disable noise suppression.

As per DA7210 data sheet, ALC and noise suppression can be enabled
only if certain conditions are met. This condition checks are handled
by simply using "_EXT" version of controls to capture change events.

Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Acked-by: Liam Girdwod <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: da7210: Add support for mute and zero cross controls

This patch adds support for below set of controls,
(1) Mute controls for MIC, AUX and ADC
(2) Zero cross controls for head phone, AUX, INPGA and line out
(3) Head phone mode selection - class H or G

It also adds digital_mute() call back.

Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: ak4641: Remove unused codec field from struct ak4641_priv

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: ssm2602: Use snd_soc_update_bits for read-modify-write

Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: WM9081 interrupt status register is volatile

Not that we have interrupt handling in the driver at the minute.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: sgtl5000: Fix setting mic bias resistor

According to the datasheet:
CHIP_MIC_CTRL 0x002A

BITS[9:8] BIAS_RESISTOR
        0x0 = Powerd off
        0x1 = 2.0 kohm
        0x2 = 4.0 kohm
        0x3 = 8.0 kohm

To set mic bias resistor, we need to update bits[9:8] of
SGTL5000_CHIP_MIC_CTRL register.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: sgtl5000: Fix define for SGTL5000_BIAS_R_MASK

According to the datasheet:
CHIP_MIC_CTRL 0x002A

BITS[9:8] BIAS_RESISTOR
        0x0 = Powerd off
        0x1 = 2.0 kohm
        0x2 = 4.0 kohm
        0x3 = 8.0 kohm

Thus SGTL5000_BIAS_R_MASK should be defined as 0x0300 instead of 0x0200.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: ad193x: Use snd_soc_update_bits for read-modify-write

Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Fix prefixing of DAPM controls

We don't want to clear the prefix while we're creating the DAPM controls
for the device as the prefix is applied during control creation.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Convert WM9081 to table based control init

At least for the core controls, the optionally selected controls are still
added programatically.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Update WM1811 DCS codes for latest evaluation results

Evaluation of larger quantities of material has provided new DCS codes
values to be applied for WM1811.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: wm8580: Use snd_soc_update_bits for read-modify-write

Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8900: Use snd_soc_update_bits for read-modify-write

Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8900: Fix the mask defines

Now we have done bitwise NOT against the mask bits for the defines of
WM8900_REG_CLOCKING1_BCLK_MASK,
WM8900_REG_CLOCKING1_OPCLK_MASK and WM8900_LRC_MASK.

But we don't have the bitwise NOT against the mask bits for the defines of
WM8900_REG_CLOCKING2_DAC_CLKDIV,
WM8900_REG_CLOCKING2_ADC_CLKDIV and WM8900_REG_DACCTRL_AIF_LRCLKRATE.

It is error prone to mix the inconsistent meaning for different mask defines.
So lets make the defines for each mask to be corresponding to the bits
defines in datasheet. Don't add extra "bitwise NOT" to the defines.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8900: Fix wrong mask for setting DAC_CLKDIV/ADC_CLKDIV/LRCLK_MODE

After checking the datasheet, I think what we want to do here is to
clear the WM8900_REG_CLOCKING2_DAC_CLKDIV/WM8900_REG_CLOCKING2_ADC_CLKDIV/
WM8900_REG_DACCTRL_AIF_LRCLKRATE bits and then OR with div value.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8741: Use snd_soc_cache_sync to sync reg_cache with the hardware

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8741: Fix setting interface format for DSP modes

According to the datasheet:
Format Control (05h)
BITS[3:2]
        FMT[1:0] Audio data format selection
                00 = right justified mode
                01 = left justified mode
                10 = I2S mode
                11 = DSP mode
BIT[4]  LRP Polarity selec for LRCLK/DSP mode select
                0 = normal LRCLK poalrity/DSP mode A
                1 = inverted LRCLK poarity/DSP mode B

For SND_SOC_DAIFMT_DSP_A, we should set 0x000C instead of 0x0003.
For SND_SOC_DAIFMT_DSP_B, we should set 0x001C instead of 0x0013.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

MANITAINERS: Add Cragganmore reference platform to Wolfson support

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: da7210: Add support for High pass and Voice filters for ADC and DAC

This patch add controls for setting cut-off for high pass and voice
filters of ADC and DAC. There are also switches to enable/disable
these filters.

Also removed hard coded, fixed  values of these parameters used by
previous version of driver.

Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: da7210: Add support for ADC & DAC equalizers

This patch adds support for ADC and DAC five band equalizers
available on DA7210 codec.

Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Tegra: sparse cleanup

Fixes the following sparse warnings:

sound/soc/tegra/tegra_das.c:215:8: warning: Using plain integer as NULL pointer
sound/soc/tegra/tegra_das.c:237:8: warning: Using plain integer as NULL pointer
sound/soc/tegra/tegra_pcm.c:370:32: warning: symbol 'tegra_pcm_platform' was not declared. Should it be static?

Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

MAINTAINERS: Add maintainer for Analog Devices sound CODECs

The MAINTAINERS  entry for the ADI sound CODEC drivers currently only lists the
ADI devices-drivers-devel mailing-list. Add myself as additional contact, since
I'm the person at ADI who is currently doing most of the work on these drivers.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: Request core to inline the DAPM sequence

We need to have as less time between McPDM shutdown,
and power down of the DAC on the twl6040 codec as possible.
Request core to ignore the pmdown_time for the playback
stream.
Backround: with the McPDM protocol we are sendning not only
the pure audio stream, but OMAP McPDM also transmits
additional information (for example offset cancellation).
If McPDM is stopped prior to the DAC this information will
be not sent to the codec, which can result noise rendered
by the twl6040 codec.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: core: Add flag to ignore pmdown_time at pcm_close

With this flag codec drivers can indicate that it is desired
to ignore the pmdown_time for DAPM shutdown sequence when
playback stream is stopped.
The DAPM sequence will be executed without delay in this case.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: da7210: bugfix for head phone volume control

This patch takes care of reserved bits of headphone volume
register by using correct volume range.

Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: ad193x: Fix define of AD193X_PLL_INPUT_MASK

Current code defines AD193X_PLL_INPUT_MASK as (~0x6) which is quite
different from other MASK defines.
To make it consistent with other mask defines, define AD193X_PLL_INPUT_MASK
as 0x6 and change the code accordingly.
I think this change improves the readability.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8990: Use snd_soc_update_bits for read-modify-write

Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write

This patch also includes a comment fix in wm8990_set_dai_pll(),
if freq_in and freq_out are 0, what we do is to clear WM8990_PLL_ENA bit.
Thus the comment should be "Turn off PLL".

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8990: Fix wrong bit setting for WM8990_POWER_MANAGEMENT_2

If (fakepower & ((1 << WM8990_INMIXR_PWR_BIT) | (1 << WM8990_AINRMUX_PWR_BIT)))
is false, we should clear WM8990_AINR_ENA bits instead of WM8990_AINL_ENA.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8400: Fix wrong bit setting for WM8400_POWER_MANAGEMENT_2

If (fakepower & ((1 << WM8400_INMIXR_PWR) | (1 << WM8400_AINRMUX_PWR)))
is false, we should clear WM8400_AINR_ENA bits instead of WM8400_AINL_ENA.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8991: Use snd_soc_update_bits for read-modify-write

Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8991: Fix wrong bit setting for WM8991_POWER_MANAGEMENT_2

If (fakepower & ((1 << WM8991_INMIXR_PWR_BIT)|(1 << WM8991_AINRMUX_PWR_BIT))))
is false, we should clear WM8991_AINR_ENA bits instead of WM8991_AINL_ENA.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8961: Convert codec->hw_read to snd_soc_read

codec->hw_read is broken now, let's covert to snd_soc_read.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: tlv320aic3x: Convert codec->hw_read to snd_soc_read

codec->hw_read is broken now, let's covert to snd_soc_read.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: alc5623: Convert codec->hw_read to snd_soc_read

codec->hw_read is broken now, let's covert to snd_soc_read.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: tlv320aic23: convert to soc-cache

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Convert DA7210 to table based DAPM init

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: tlv320aic32x4: Use snd_soc_update_bits for read-modify-write

Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: Rename the Earphone Driver event handler

Since the event handler is only used by the Earphone Driver, it is better
to rename it from twl6040_power_mode_event to twl6040_ep_drv_event.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: Change event ordering for Earphone driver

It is better to switch HS Power Mode (if it was in low power mode) before
we enable the Earpiece driver. The switched off EP driver can filter out
noise coming from the Low Power to High Performance transition on the
HSL DAC.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: Remove PLL usage restrictions

There is no limitation dictated by outputs or inputs regarding to the
selected PLL (LP/HP).
Remove the checks for this, and allow all path with any PLL configuration.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: Remove Capture restriction for 17.64MHz sysclk

Capture is supported in all PLL configuration.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Update WM5100 accessory detection for revision A

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: ak4535: fixup cache register table

ak4535_reg should be 8bit, but cache table is defined as 16bit.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

ASoC: ak4642: fixup cache register table

ak4642 register was 8bit, but cache table was defined as 16bit.
ak4642 doesn't work correctry without this patch.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

ASoC: sta32x: Write the register default value to cache for reserved registers

Chip documentation explicitly requires that the reset values
of reserved register bits are left untouched.

codec->hw_read is broken now.
Here we use below trick to avoid writing to reserved registers while resume.
Write the register default value to cache for reserved registers,
so the write to the these registers are suppressed by the cache
restore code when it skips writes of default registers.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: sta32x: Set reg_cache_default to sta32x_regs

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: pxa: Remove redundant snd_soc_dapm_sync() calls from machine drivers

The core will sync DAPM as part of the card initialization, there is no
need for machine drivers to do so during their setup.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Make SND_SOC_SAARB and SND_SOC_TAVOREVB3 select MFD_88PM860X

In saarb_pm860x_init() and evb3_pm860x_init(), we call
pm860x_hs_jack_detect() and pm860x_mic_jack_detect() which in turn
calls pm860x_set_bits().
Thus make SND_SOC_SAARB and SND_SOC_TAVOREVB3 select MFD_88PM860X.

This patch fixes below build error if CONFIG_MFD_88PM860X is not configured.

  LD      .tmp_vmlinux1
sound/built-in.o: In function `pm860x_write_reg_cache':
last.c:(.text+0x29e9c): undefined reference to `pm860x_reg_write'
sound/built-in.o: In function `pm860x_set_bias_level':
last.c:(.text+0x29ecc): undefined reference to `pm860x_set_bits'
last.c:(.text+0x29f00): undefined reference to `pm860x_reg_write'
last.c:(.text+0x29f18): undefined reference to `pm860x_reg_write'
sound/built-in.o: In function `pm860x_read_reg_cache':
last.c:(.text+0x29f40): undefined reference to `pm860x_reg_read'
sound/built-in.o: In function `pm860x_probe':
last.c:(.text+0x2a034): undefined reference to `pm860x_bulk_read'
sound/built-in.o: In function `pm860x_codec_handler':
last.c:(.text+0x2a344): undefined reference to `pm860x_reg_read'
last.c:(.text+0x2a354): undefined reference to `pm860x_reg_read'
sound/built-in.o: In function `pm860x_mic_jack_detect':
last.c:(.text+0x2a450): undefined reference to `pm860x_set_bits'
sound/built-in.o: In function `pm860x_hs_jack_detect':
last.c:(.text+0x2a4d0): undefined reference to `pm860x_set_bits'
last.c:(.text+0x2a4f8): undefined reference to `pm860x_set_bits'
last.c:(.text+0x2a510): undefined reference to `pm860x_set_bits'
make: *** [.tmp_vmlinux1] Error 1

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: da7210: Add support for other DAI word lengths, format and mode

This patchs adds support for following,
(1) DAI 20 and 32 bit word sizes
(2) DAI left and right justified formats
(3) DAI slave mode

Signed-off-by: Ashish Chavan <ashish.chavan@kpitcummins.com>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: Workaround for headset DC offset caused pop noise

Both Headset DAC need to be turned on/off at the same time before
any of the output drivers are enabled (HS Left/Right, Earpiece).
Move the HS DAC enable code to sequenced DAPM_SUPPLY, and attach
it to the DACs.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: Support for vibra output paths

twl6040 have two vibra output drivers.
They can be operated with audio stream coming through
the PDM interface (fifth channel).
The vibra outputs can be controlled via the input/FF
driver as well.
Selection between the two mode is implemented within
the codec driver, the input/FF driver can only operate if
the routing is set to "Input FF".
Changing from "Input FF" to "Audio PDM" mode is protected
as well: The switchin can only be done, if there is no
running effect from the input/FF.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Input: twl6040-vibra: Check the selected path for vibra

The VIBSELL/R bit in the VIBCTLL/R register tells the source of the data,
which is going to be used to drive the attached motor(s).
Do not allow effect execution if any of the channels are set to receive
audio data.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

MFD: twl6040: function to query the vibra status for clients

If the client only interested, if any of the vibra channels enabled, or
if any of the channels are set to receive audio data via PDM.

This function targets mainly the vibra driver, so it can check if it is
allowed to execute effects ot not.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

MFD: twl6040: Cache the vibra control registers

The vibra control register will be used from the ASoC codec driver as well.
In order to avoid latency issues caused by I2C read access, cache the two
control register within the core driver, so we do not need to reach out
to the chip to read it back.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Input: twl6040: Simplify vibra regsiter definitions

The bits within the two control registers (for left and right channel)
are identical.
Use common names for the bits acros the two register.
Also add the missing definition for the path selection bit.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: da7210: convert to soc-cache

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Remove impossible case from wm8994_hw_params

We set hw_params callback for wm8994_aif3_dai_ops to wm8994_aif3_hw_params.
Thus no need to check wm8994-aif3 in wm8994_hw_params.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Delete ads117x.h

This is not required after multi-component patch.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: ak4642: convert to soc-cache

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Instantiate card widgets immediately

This ensures they are available prior to the card late_probe().

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Implement WM5100 accessory detection support

The WM5100 includes an advanced, low power, accessory detect subsystem
capable of detecting both accessory presence and button presses while
the device is in an ultra low power mode. Implement initial support for
this.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Add missing default for WM5100 Clocking 1

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Fix typo in Kconfig symbol for tlv320aic32x4

It is currently named "TVL" instead of "TLV".

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: tlv320dac33: Convert to table based init

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl4030: Convert to table based init

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: twl6040: Convert to table based init

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Writing register default value for the reset register

The WM8983 can be reset by performing a write of any value to
the software reset register.
To avoid writing to the software reset register while resume,
we should write the same value in wm8983_reg_defs to software
reset register in wm8983_probe().
The write to the reset register is suppressed by the cache
restore code when it skips writes of default registers.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Convert Goni to data based DAPM init

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>

ASoC: sdp3430: Let core to deal with the DAPM widgets

Pass the DAPM widgets/routes via the snd_soc_card struct
to core.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: osk5912: Let core to deal with the DAPM widgets

Pass the DAPM widgets/routes via the snd_soc_card struct
to core. With this change we do not need the init function
since the remaining snd_soc_dapm_enable_pin calls are
not needed.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: n810: Let the core to register DAPM widgets/routes and controls

Pass the DAPM widgets/routes and static controls via the
snd_soc_card struct to core. In this way the machine driver
does not need to handle the DAPM widgets/routes.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: am3517evm: Let core to deal with the DAPM widgets

Pass the DAPM widgets/routes via the snd_soc_card struct
to core. With this change we do not need the init function
since the remaining snd_soc_dapm_enable_pin calls are
not needed.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Anuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: sdp4430: No need to call dapm_pin_enable at init time

Widgets are connected by default.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: sdp4430: Let core to deal with the DAPM widgets

Pass the DAPM widgets/routes via the snd_soc_card struct
to core.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: zoom2: No need to call dapm_pin_enable at init time

Widgets are connected by default.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: zoom2: Let core to deal with the DAPM widgets

Pass the DAPM widgets/routes via the snd_soc_card struct
to core.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: OMAP machines: Remove soc_dapm_sync() call from init

No need to call soc_dapm_sync at init time.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Anuj Aggarwal <anuj.aggarwal@ti.com>
Cc: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Gražvydas Ignotas <notasas@gmail.com>
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Convert Jive to table based init

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>

ASoC: Convert SMDK WM8580 to table based DAPM init

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>

ASoC: Convert SmartQ to table based init

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>

ASoC: Convert RX1950 to table based init

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>

ASoC: Convert H1940 to table based init

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>

ASoC: Convert Simtec machines to table based DAPM init

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: fix checkpatch.pl error in omap-mcbsp

Signed-off-by: Michael Opdenacker <michael.opdenacker@linaro.org>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: ak4535: convert to soc-cache

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8988: Convert to snd_soc_cache_sync

Convert to snd_soc_cache_sync for sync reg_cache with the hardware.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8974: Convert to snd_soc_cache_sync

Convert to snd_soc_cache_sync for sync reg_cache with the hardware.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8971: Convert to snd_soc_cache_sync

Convert to snd_soc_cache_sync for sync reg_cache with the hardware.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: wm8960: Convert to snd_soc_cache_sync

Convert to snd_soc_cache_sync for sync reg_cache with the hardware.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>