John Crispin [Sun, 22 Feb 2015 08:29:14 +0000 (08:29 +0000)]
ipq806x: fix "reboot" command
The watchdog driver already registers a restart notifier, we just have
to enable it in the config and in the DT to fix the "reboot" command.
This is done by integratin the following patch-set:
https://lkml.org/lkml/2015/2/20/610
I'm copy-pasting the description below:
qcom-wdt is currently assuming the presence of a dedicated node in DT
to gets its configuration. However, on msm architecture, the watchdog is
usually part of the timer block. So this patch-set is changing the driver
and slightly enhancing the timer DT bindings to provide the relevant clocks
and interrupts.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 44504
John Crispin [Sun, 22 Feb 2015 08:29:07 +0000 (08:29 +0000)]
ipq806x: enable watchdog kernel option
Some bootloaders seem to trigger the watchdog during the boot process,
therefore the lack of watchdog driver trigger a reboot a few seconds
after boot. So we'll enable it here to avoid it.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
SVN-Revision: 44503
John Crispin [Sun, 22 Feb 2015 08:29:01 +0000 (08:29 +0000)]
kernel: Fix USB gadget modules for v3.18
Updated patch that fixes whitespace and supports kernel v3.3 too.
Signed-off-by: Owen Kirby <osk@exegin.com>
SVN-Revision: 44502
John Crispin [Sun, 22 Feb 2015 08:28:48 +0000 (08:28 +0000)]
mpc85xx: add mpic timer clock frequency to avoid boot log warning
MPIC timers are enabled in the config, however a devicetree clock setting
is missing causing the following error:
/soc@
ffe00000/timer@41100: cannot get timer frequency.
/soc@
ffe00000/timer@42100: cannot get timer frequency.
This patch adds the missing clock and avoids the error.
It's a functional copy of this code
do_fixup_by_compat_u32(blob, "fsl,mpic",
"clock-frequency", get_bus_freq(0), 1);
in arch/powerpc/cpu/mpc85xx/fdt.c in the u-boot code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
SVN-Revision: 44501
John Crispin [Sun, 22 Feb 2015 08:28:42 +0000 (08:28 +0000)]
ramips: rt288x: add missing symbol
Defaulting to disabled, based on the value of
the (old?) CONFIG_RALINK_USBPHY
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 44500
John Crispin [Sun, 22 Feb 2015 08:28:35 +0000 (08:28 +0000)]
ramips: nexx wt3020: fix status led
For Nexx WT3020 board_name is wt3020, not nexx-wt3020
root@OpenWrt:~# . /lib/ramips.sh; echo $(ramips_board_name)
wt3020
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 44499
Nicolas Thill [Sun, 22 Feb 2015 01:31:21 +0000 (01:31 +0000)]
packages: remove uneeded PKG_BUILD_DIR overrides
Signed-off-by: Nicolas Thill <nico@openwrt.org>
SVN-Revision: 44498
Rafał Miłecki [Fri, 20 Feb 2015 07:07:53 +0000 (07:07 +0000)]
bcm53xx: add one more NVRAM possible size (0x180000)
Size 0x160000 was added to support Buffalo WZR-600DHP2, however Netgear
devices (R6250, R8000) require 0x180000.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44497
John Crispin [Thu, 19 Feb 2015 14:30:03 +0000 (14:30 +0000)]
mpc85xx: set v3.18 as default
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44496
John Crispin [Thu, 19 Feb 2015 14:04:47 +0000 (14:04 +0000)]
ralink: bump to v3.18
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44495
John Crispin [Thu, 19 Feb 2015 14:04:41 +0000 (14:04 +0000)]
ramips: fix the mt7628 dts file
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44494
Felix Fietkau [Thu, 19 Feb 2015 10:30:39 +0000 (10:30 +0000)]
tools/patchelf: fix portability issue breaking mac os x builds (#18998)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44493
John Crispin [Thu, 19 Feb 2015 09:07:06 +0000 (09:07 +0000)]
at91: Add dts for Exegin Q5x boards.
Signed-off-by: Owen Kirby <osk@exegin.com>
SVN-Revision: 44492
John Crispin [Thu, 19 Feb 2015 09:06:56 +0000 (09:06 +0000)]
at91: USB gadget subsystem cleanup and driver fix.
Signed-off-by: Owen Kirby <osk@exegin.com>
SVN-Revision: 44491
John Crispin [Thu, 19 Feb 2015 09:06:49 +0000 (09:06 +0000)]
at91: Enable power and reset controller drivers.
Signed-off-by: Owen Kirby <osk@exegin.com>
SVN-Revision: 44490
John Crispin [Wed, 18 Feb 2015 13:35:46 +0000 (13:35 +0000)]
at91: bump to v3.18
Signed-off-by: Your Name <blogic@openwrt.org>
SVN-Revision: 44489
Jo-Philipp Wich [Wed, 18 Feb 2015 13:28:28 +0000 (13:28 +0000)]
include: netfilter: fix packaging of LOG target for Linux >= 3.16 (#19031)
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44488
John Crispin [Wed, 18 Feb 2015 09:49:38 +0000 (09:49 +0000)]
au1000: fix 3.18 and set it as default
Thanks to Bruno Randolf for testing and Manuel Lauss for providing a fix.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44487
Jo-Philipp Wich [Tue, 17 Feb 2015 21:26:39 +0000 (21:26 +0000)]
ar71xx: fix 82_patch_ath10k
The firware md5sum check never worked due to missing dollar signs.
Also suppress
`md5sum: can't open '/lib/firmware/ath10k/QCA988X/hw2.0/firmware-3.bin'`
error on any board not using ath10k.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44486
John Crispin [Tue, 17 Feb 2015 20:28:36 +0000 (20:28 +0000)]
mpc85xx: add v3.18 support
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44485
John Crispin [Tue, 17 Feb 2015 15:59:28 +0000 (15:59 +0000)]
hostapd: fix c&p typo
https://dev.openwrt.org/ticket/19010
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44484
John Crispin [Tue, 17 Feb 2015 14:33:29 +0000 (14:33 +0000)]
ar71xx: make v3.18 default
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44482
John Crispin [Tue, 17 Feb 2015 14:33:13 +0000 (14:33 +0000)]
kernel: re-enable the firmware loader
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44481
Steven Barth [Tue, 17 Feb 2015 14:14:51 +0000 (14:14 +0000)]
netifd: various device config / event fixes (thx Hans Dedecker)
Signed-off-by: Steven Barth <steven@midlink.org>
SVN-Revision: 44480
Steven Barth [Tue, 17 Feb 2015 14:14:39 +0000 (14:14 +0000)]
iproute2: bump version from v3.18.0 to v3.19.0
with refreshed patches
Signed-off-by: Russell Senior <russell@personaltelco.net>
SVN-Revision: 44479
John Crispin [Mon, 16 Feb 2015 21:19:18 +0000 (21:19 +0000)]
ramips: Buffalo WZR-AGL300NH target support
I got work with this patch.
Ethernet switch (includes VLAN), WiFi connected via PCIe, LEDs, buttons.
In mtd partion map of DTS file, I renamed Linux firmware regions (kernel + root squashfs) to “firmware”because it allows kernel to split kernel and roots and rootfsdata.
signed-off-by: ngc@ff.iij4u.or.jp
——
——
SVN-Revision: 44470
John Crispin [Mon, 16 Feb 2015 21:18:59 +0000 (21:18 +0000)]
ramips: enables rt288x PCIe
To choose whether bulid or not RT288x PCIe bus driver, CONFIG_SOC_RT2880 is wrong.
Here is its fix, and enables PCIe bus driver for some targets which have 2nd WiFi chipset via PCIe bus.
signed-off-by: ngc@ff.iij4u.or.jp
————
————
SVN-Revision: 44469
John Crispin [Mon, 16 Feb 2015 21:18:48 +0000 (21:18 +0000)]
oxnas: fix itb generation
- according to imx6 Makefile and u-Boot documentation is itb
and probably should not be changed
- this fixes build error if CONFIG_TARGET_ROOTFS_INCLUDE_FIT is set
(missing .itb file)
- use DTS_DIR (like in imx6 Makefile)
only compile tested
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
Acked-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 44468
Rafał Miłecki [Mon, 16 Feb 2015 19:51:21 +0000 (19:51 +0000)]
bcm53xx: include kmod-brcmfmac in default profile
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44467
Rafał Miłecki [Mon, 16 Feb 2015 19:36:35 +0000 (19:36 +0000)]
mac80211: brcmfmac: Add PCIe support option
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44466
Rafał Miłecki [Mon, 16 Feb 2015 19:11:38 +0000 (19:11 +0000)]
mac80211: brcmfmac: Add SDIO support option
This patch adds SDIO support for the brcmfmac driver.
For now only very few boards need it.
Signed off by: José Vázquez Fernández <ppvazquezfer@gmail.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44465
Rafał Miłecki [Mon, 16 Feb 2015 16:13:23 +0000 (16:13 +0000)]
bcm53xx: sprom: extract for PCI host
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44464
Rafał Miłecki [Mon, 16 Feb 2015 16:10:05 +0000 (16:10 +0000)]
bcm53xx: sprom: prepare to support other hosttype-s
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44463
Imre Kaloz [Mon, 16 Feb 2015 12:48:05 +0000 (12:48 +0000)]
mvebu: refresh 3.18 patches
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 44462
Felix Fietkau [Mon, 16 Feb 2015 09:07:19 +0000 (09:07 +0000)]
netifd: update to the latest version, reverts a commit causing MTU issues (fixes #18869)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 44461
John Crispin [Mon, 16 Feb 2015 08:00:17 +0000 (08:00 +0000)]
linux: fix kmod-usb-net-* for >= 3.17
Kernel commit
1bb5a356c3ea ("net: reduce USB network driver config
options.") hid the USB network drivers behind the new config symbol
CONFIG_USB_NET_DRIVERS.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
SVN-Revision: 44460
John Crispin [Sun, 15 Feb 2015 21:15:42 +0000 (21:15 +0000)]
ar71xx: fix mv88e6063 compile for 3.14
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44459
John Crispin [Sun, 15 Feb 2015 21:15:21 +0000 (21:15 +0000)]
ar71xx: fix a compile bug in 902-unaligned_access_hacks.patch
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44458
John Crispin [Sun, 15 Feb 2015 19:55:37 +0000 (19:55 +0000)]
procd: fix PKG_CONFIG_DEPENDS
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44457
John Crispin [Sun, 15 Feb 2015 19:45:29 +0000 (19:45 +0000)]
ar71xx: add v3.18 support
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44456
Imre Kaloz [Sat, 14 Feb 2015 22:18:35 +0000 (22:18 +0000)]
mvebu: fix WRT1900AC ubinized images
The current pxa3xx_nand driver doesn't support sub-page writing,
so the VID header offset must be specified explicitly.
Signed-off-by: Claudio Leite <leitec@staticky.com>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 44455
John Crispin [Sat, 14 Feb 2015 20:48:53 +0000 (20:48 +0000)]
ralink: fix the config files
oops, accidently moved instead of copied them
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44454
John Crispin [Sat, 14 Feb 2015 20:48:42 +0000 (20:48 +0000)]
ar71xx: ZyXEL NBG6716 rfkill switch fix
ZyXEL NBG6716 "rfkill" is a switch, not a button.
Signed-off-by: Marcin Mikolajczak <gr4ffy at gmail.com>
SVN-Revision: 44453
John Crispin [Sat, 14 Feb 2015 20:48:37 +0000 (20:48 +0000)]
scripts: fix getver git dir check
Git internals are referenced by .git which isn't necessarily a
directory. It may also be a file that references the actual .git
directory using the gitdir directive.
If .git is assumed to be a directory the build will not be able to get
the correct version when openwrt is included as a git submodule because
when used as a submodule .git will actually be a file referencing to a
subdirectory in the parent's git dir.
When the correct version is not detected some image generation tools
will fail because the OpenWrt string will be 'OpenWrtunknown' which is
too long for some header formats.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
SVN-Revision: 44452
John Crispin [Sat, 14 Feb 2015 20:48:32 +0000 (20:48 +0000)]
lantiq: disable buffered writes on Intel command set flash
Some Lantiq SoCs are not able to use buffered writes properly with
Intel command set flash due to the way NOR addresses on EBU are
manipulated. This patch disables buffered writes on those devices.
The only device affected at the moment is ARV4510PW, others use
AMD/Fujitsu command set.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44451
John Crispin [Sat, 14 Feb 2015 20:48:26 +0000 (20:48 +0000)]
lantiq: Fix flash for targets with NO_XIP
For targets with NO_XIP ltq_mtd->map[i].phys equals -1 and devm_ioremap fails.
Fix this by using pdev->resource[i].start instead.
Signed-off-by: Matti Laakso <malaakso@elisanet.fi>
SVN-Revision: 44450
John Crispin [Sat, 14 Feb 2015 20:48:20 +0000 (20:48 +0000)]
brcm2708: add kmod-hwmon-bcm2835 support and more missing symbols
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 44449
John Crispin [Sat, 14 Feb 2015 20:48:14 +0000 (20:48 +0000)]
brcm2708: force uart as the default console for procd and remove nonexistent console
procd gets last console from cmdline, so swapping tty1 (framebuffer) and ttyAMA0 (uart) is enough to force procd output via uart
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 44448
John Crispin [Sat, 14 Feb 2015 20:48:08 +0000 (20:48 +0000)]
brcm2708: add board detection and LED support
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 44447
John Crispin [Sat, 14 Feb 2015 20:47:58 +0000 (20:47 +0000)]
uci-defaults: add ucidef_set_led_mmc
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 44446
Nicolas Thill [Sat, 14 Feb 2015 13:53:51 +0000 (13:53 +0000)]
package/valgrind: fix build on eglibc
configure tries to guess pagesize by calling getconf, provided by eglibc and compiled for the target, not the host.
Signed-off-by: Nicolas Thill <nico@openwrt.org>
SVN-Revision: 44445
Nicolas Thill [Sat, 14 Feb 2015 13:53:44 +0000 (13:53 +0000)]
generic: ocf: irq compat stuff is not needed anymore
Signed-off-by: Nicolas Thill <nico@openwrt.org>
SVN-Revision: 44444
Imre Kaloz [Sat, 14 Feb 2015 12:21:34 +0000 (12:21 +0000)]
fix typo
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 44443
Imre Kaloz [Sat, 14 Feb 2015 10:45:12 +0000 (10:45 +0000)]
generic: upgrade to 3.18.7
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 44442
John Crispin [Fri, 13 Feb 2015 10:54:01 +0000 (10:54 +0000)]
ixp4xx: fix gpio_line_set() logic, fixes #18986
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44439
John Crispin [Fri, 13 Feb 2015 10:53:54 +0000 (10:53 +0000)]
hostapd: backport BSSID black/whitelists
This change adds the configuration options "bssid_whitelist" and
"bssid_blacklist" used to limit the AP selection of a network to a
specified (finite) set or discard certain APs.
This can be useful for environments where multiple networks operate
using the same SSID and roaming between those is not desired. It is also
useful to ignore a faulty or otherwise unwanted AP.
In many applications it is useful not just to enumerate a group of well
known access points, but to use a address/mask notation to match an
entire set of addresses (ca:ff:ee:00:00:00/ff:ff:ff:00:00:00).
This is especially useful if an OpenWrt device with two radios is used to
retransmit the same network (one in AP mode for other clients, one as STA for
the uplink); the following configuration prevents the device from associating
with itself, given that the own AP to be avoided is using the bssid
'C0:FF:EE:D0:0D:42':
config wifi-iface
option device 'radio2'
option network 'uplink'
option mode 'sta'
option ssid 'MyNetwork'
option encryption 'none'
list bssid_blacklist 'C0:FF:EE:D0:0D:42/00:FF:FF:FF:FF:FF'
This change consists of the following cherry-picked upstream commits:
b3d6a0a8259002448a29f14855d58fe0a624ab76
b83e455451a875ba233b3b8ac29aff8b62f064f2
79cd993a623e101952b81fa6a29c674cd858504f
(squashed to implement bssid_{white,black}lists)
0047306bc9ab7d46e8cc22ff9a3e876c47626473
(Add os_snprintf_error() helper)
Signed-off-by: Stefan Tomanek <stefan.tomanek+openwrt@wertarbyte.de>
SVN-Revision: 44438
John Crispin [Fri, 13 Feb 2015 07:42:13 +0000 (07:42 +0000)]
kexec-tools: bump version from v2.0.4 to v2.0.9.
- kexec-tools is now distributed with tarballs of .tar.gz and .tar.xz
format; .tar.bz2 are not provided anymore.
- Add CONFIG_KEXEC_LZMA for selecting lzma support.
Patches are updated along to:
- Remove the now unnecessary patch 0004-mips_regdefs.patch.
- Drop 100-reduce_size.patch because the size reduction is marginal.
- Allow zlib and lzma support coexist together. This patch has been
merged into upstream project.
- Fix kexec-tools' configure.ac.
- Fix a few compilation warnings.
Size comparison of stripped binaries of kexec malta target with both
zlib and lzma support enabled.
- Before: 41447
- After: 42583
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 44437
John Crispin [Fri, 13 Feb 2015 07:42:05 +0000 (07:42 +0000)]
kexec-tools: show up only when KERNEL_KEXEC is enabled.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 44436
John Crispin [Fri, 13 Feb 2015 07:38:38 +0000 (07:38 +0000)]
brcm2708-gpu-fw: simplify target dependencies
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 44435
John Crispin [Fri, 13 Feb 2015 07:38:33 +0000 (07:38 +0000)]
brcm2708: fix spidev
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 44434
John Crispin [Fri, 13 Feb 2015 07:38:27 +0000 (07:38 +0000)]
brcm2708: refresh patches
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 44433
John Crispin [Fri, 13 Feb 2015 07:38:00 +0000 (07:38 +0000)]
brcm2708: add missing config symbols and fix kernel modules for Raspberry Pi 2 by removing local version
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 44432
John Crispin [Fri, 13 Feb 2015 07:37:55 +0000 (07:37 +0000)]
brcm2708: add subtarget copyright and use better board names
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 44431
John Crispin [Fri, 13 Feb 2015 07:29:32 +0000 (07:29 +0000)]
ar7: switch to v3.18
Thank you Dimitri for testing this.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44430
John Crispin [Fri, 13 Feb 2015 07:29:25 +0000 (07:29 +0000)]
generic: improve kexec support of MIPS.
- Allow --command-line parameters of kexec-tools be parsed and used by
the kernel.
- For malta machine, mark kernel code and kernel data segments as
"System RAM" instead of "reserved" in /proc/iomem, otherwise
kexec-tools will complain that program segments in ELF kernel file
are invalid.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 44429
John Crispin [Fri, 13 Feb 2015 07:29:17 +0000 (07:29 +0000)]
lantiq: fix DGN3500 root device
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 44428
John Crispin [Fri, 13 Feb 2015 07:29:10 +0000 (07:29 +0000)]
ar71xx: Add profile and build image for TP-Link MR12U v1
This patch adds corrected profile and build image for the TL-MR12U board.
Unfortunately i cannot test the factory image since i can't find anywhere
the original chinese firmware but
the generated openwrt-ar71xx-generic-tl-mr12u-v1-squashfs-sysupgrade.bin
worked just fine over a modified mr3040 factory image i managed to modify
to initially flash the mr12u from the original firmware.
Proper kernel support probably should be added since cat /proc/cpuinfo shows
MR13U.
Signed-off-by: Daniel Petre <daniel.petre@gmail.com>
SVN-Revision: 44427
John Crispin [Fri, 13 Feb 2015 07:29:03 +0000 (07:29 +0000)]
ar71xx: Add user-space support for TP-Link MR12U v1
This patch adds user-space support for the TL-MR12U board based on the mr13u patches.
Signed-off-by: Daniel Petre <daniel.petre@gmail.com>
SVN-Revision: 44426
John Crispin [Fri, 13 Feb 2015 07:28:53 +0000 (07:28 +0000)]
ar71xx: ZyXEL NBG6716 add gpio usb power on/off
ZyXEL NBG6716 add missing GPIO USB power on/off
Signed-off-by: Marcin Mikolajczak <gr4ffy at gmail.com>
SVN-Revision: 44425
Rafał Miłecki [Thu, 12 Feb 2015 20:13:20 +0000 (20:13 +0000)]
kernel: mtdsplit_uimage: fix passed info about buf size
We obviously can't use sizeof(*buf) which is always 1.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44424
Nicolas Thill [Thu, 12 Feb 2015 17:30:09 +0000 (17:30 +0000)]
sunxi: A20-OLinuXino-Lime profile rename leftover
Signed-off-by: Nicolas Thill <nico@openwrt.org>
SVN-Revision: 44423
Luka Perkov [Thu, 12 Feb 2015 14:39:26 +0000 (14:39 +0000)]
kirkwood: Seagate GoFlex Net
Add GoFlex Net "Board Name" , set and cleanup network default and LEDs.
Remove kmod-rtc-marvell from default packages, as the GoFlex net does not have a RTC.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
SVN-Revision: 44422
John Crispin [Thu, 12 Feb 2015 11:15:56 +0000 (11:15 +0000)]
lantiq: make m25p80 work again
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44421
John Crispin [Thu, 12 Feb 2015 09:17:04 +0000 (09:17 +0000)]
lantiq: fix mac addr assignment inside lantiq_etop
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44420
John Crispin [Thu, 12 Feb 2015 08:23:45 +0000 (08:23 +0000)]
lantiq: PCI should be enabled on vrx200
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44419
John Crispin [Thu, 12 Feb 2015 08:07:39 +0000 (08:07 +0000)]
ralink: make the mt7621 irq core with with the new CM api
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44418
John Crispin [Thu, 12 Feb 2015 08:07:27 +0000 (08:07 +0000)]
ar71xx: ZyXEL NBG6716 led/buttons cleanup
ZyXEL NBG6716 led/buttons cleanup
- improper numbered leds
- improper named buttons
Signed-off-by: Marcin Mikolajczak <gr4ffy at gmail.com>
SVN-Revision: 44417
John Crispin [Thu, 12 Feb 2015 08:07:20 +0000 (08:07 +0000)]
generic: fix broken patch in the transition of 3.19 from -rc5 to release .0
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
SVN-Revision: 44416
Rafał Miłecki [Thu, 12 Feb 2015 07:50:07 +0000 (07:50 +0000)]
kernel: mtdsplit_uimage: read more data to match Edimax needs
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44415
Rafał Miłecki [Thu, 12 Feb 2015 07:44:34 +0000 (07:44 +0000)]
kernel: mtdsplit_uimage: use separated buffer for reading data
We shouldn't read data directly into the header struct, as some devices
(e.g. Edimax) need more bytes due to some extra header.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44414
Rafał Miłecki [Thu, 12 Feb 2015 07:23:40 +0000 (07:23 +0000)]
kernel: mtdsplit_uimage: add parser for Edimax devices
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44413
Rafał Miłecki [Thu, 12 Feb 2015 06:57:24 +0000 (06:57 +0000)]
mtdsplit_uimage: more generic header verify function
Some devices have uImage headers after some extra headers (e.g. Edimax
devices). To support such cases our verify callback function should be
allowed to return header offset, not just a boolean value.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44412
Rafał Miłecki [Wed, 11 Feb 2015 18:11:22 +0000 (18:11 +0000)]
kernel: fix bgmac check for chip ID
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44411
Rafał Miłecki [Wed, 11 Feb 2015 17:35:09 +0000 (17:35 +0000)]
kernel: backport mainlined bgmac patches from 3.19
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44410
Jo-Philipp Wich [Wed, 11 Feb 2015 15:12:32 +0000 (15:12 +0000)]
base-files: fix target/subtarget value in /etc/openwrt_release
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 44409
Rafał Miłecki [Wed, 11 Feb 2015 14:41:07 +0000 (14:41 +0000)]
bcm53xx: use bcm47xx_wdt for restarting device
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 44408
John Crispin [Wed, 11 Feb 2015 13:50:56 +0000 (13:50 +0000)]
oxnas: disable usbgadget support
usbgadget was initially enabled in the hope to support gadget mode
as it seems to be supported by the hardware.
However, it currently breaks things and doesn't work anyway, so
remove the usbgadget feature.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 44407
John Crispin [Wed, 11 Feb 2015 13:50:40 +0000 (13:50 +0000)]
brcm2708-gpu-fw: revert to github releases, adapt to bcm2708 target changes and add back InstallDev
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 44406
John Crispin [Wed, 11 Feb 2015 13:09:39 +0000 (13:09 +0000)]
brcm2708: add missing SUBTARGETS:= to makefile
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44405
John Crispin [Wed, 11 Feb 2015 13:05:37 +0000 (13:05 +0000)]
brcm2708: remove CMA_DEBUG
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 44404
John Crispin [Wed, 11 Feb 2015 13:05:31 +0000 (13:05 +0000)]
brcm2708: add Raspberry Pi 2 support
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 44403
John Crispin [Wed, 11 Feb 2015 13:05:23 +0000 (13:05 +0000)]
brcm2708: remove 3.14 support
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 44402
John Crispin [Wed, 11 Feb 2015 13:05:14 +0000 (13:05 +0000)]
ralink: fix when tx done is 0 also need to clean interrupt status
Signed-off-by: michael lee <igvtee@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44401
John Crispin [Wed, 11 Feb 2015 13:05:07 +0000 (13:05 +0000)]
mt76: update to latest git HEAD
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 44400
Nicolas Thill [Wed, 11 Feb 2015 12:13:49 +0000 (12:13 +0000)]
ramips/mt7620: add missing config symbol
Signed-off-by: Nicolas Thill <nico@openwrt.org>
SVN-Revision: 44399
Nicolas Thill [Wed, 11 Feb 2015 11:31:38 +0000 (11:31 +0000)]
oprofile: mark broken on uml
Signed-off-by: Nicolas Thill <nico@openwrt.org>
SVN-Revision: 44398
Nicolas Thill [Wed, 11 Feb 2015 11:31:26 +0000 (11:31 +0000)]
config: disable kernel tracing on uml
Signed-off-by: Nicolas Thill <nico@openwrt.org>
SVN-Revision: 44397
Nicolas Thill [Wed, 11 Feb 2015 11:31:07 +0000 (11:31 +0000)]
ebtables: disable rpath
Signed-off-by: Nicolas Thill <nico@openwrt.org>
SVN-Revision: 44396
Nicolas Thill [Wed, 11 Feb 2015 11:31:01 +0000 (11:31 +0000)]
util-linux: disable rpath
Signed-off-by: Nicolas Thill <nico@openwrt.org>
SVN-Revision: 44395
Nicolas Thill [Wed, 11 Feb 2015 11:30:56 +0000 (11:30 +0000)]
toolchain/gcc: fix an ICE on ARM (PR58595)
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=58595
Signed-off-by: Nicolas Thill <nico@openwrt.org>
SVN-Revision: 44394
projects / openwrt / staging / ynezz.git / log