openwrt/staging/blogic.git
7 years agodpaa_eth: use AVOIDBLOCK for Tx confirmation queues
Madalin Bucur [Thu, 30 Mar 2017 13:24:15 +0000 (16:24 +0300)]
dpaa_eth: use AVOIDBLOCK for Tx confirmation queues

The AVOIDBLOCK flag determines the Tx confirmation queues processing
to be redirected to any available CPU when the current one is slow
in processing them. This may result in a higher Tx confirmation
interrupt count but may reduce pressure on a certain CPU that with
the previous setting would process all Tx confirmation frames.

Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agofsl/fman: take into account all RGMII modes
Madalin Bucur [Thu, 30 Mar 2017 13:21:40 +0000 (16:21 +0300)]
fsl/fman: take into account all RGMII modes

Accept the internal delay RGMII variants.

Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agovxlan: vxlan dev should inherit lowerdev's gso_max_size
Felix Manlunas [Thu, 30 Mar 2017 00:56:43 +0000 (17:56 -0700)]
vxlan: vxlan dev should inherit lowerdev's gso_max_size

vxlan dev currently ignores lowerdev's gso_max_size, which adversely
affects TSO performance of liquidio if it's the lowerdev.  Egress TCP
packets' skb->len often exceed liquidio's advertised gso_max_size.  This
may happen on other NIC drivers.

Fix it by assigning lowerdev's gso_max_size to that of vxlan dev.  Might as
well do likewise for gso_max_segs.

Single flow TSO throughput of liquidio as lowerdev (using iperf3):

    Before the patch:    139 Mbps
    After the patch :   8.68 Gbps
    Percent increase:  6,144 %

Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agosock: avoid dirtying sk_stamp, if possible
Paolo Abeni [Thu, 30 Mar 2017 12:03:06 +0000 (14:03 +0200)]
sock: avoid dirtying sk_stamp, if possible

sock_recv_ts_and_drops() unconditionally set sk->sk_stamp for
every packet, even if the SOCK_TIMESTAMP flag is not set in the
related socket.
If selinux is enabled, this cause a cache miss for every packet
since sk->sk_stamp and sk->sk_security share the same cacheline.
With this change sk_stamp is set only if the SOCK_TIMESTAMP
flag is set, and is cleared for the first packet, so that the user
perceived behavior is unchanged.

This gives up to 5% speed-up under udp-flood with small packets.

Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoMerge branch 'ibmvnic-cleanup-resource-handling'
David S. Miller [Thu, 30 Mar 2017 22:58:43 +0000 (15:58 -0700)]
Merge branch 'ibmvnic-cleanup-resource-handling'

Nathan Fontenot says:

====================
ibmvnic: Cleanup resource handling

In order to better manage the resources of the ibmvnic driver, this set of
patches creates a set of initialization and release routines for the
drivers resources. Additionally, some patches do some re-naming of the
affected routines so that there is a common naming scheme in the driver.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoibmvnic: Cleanup failure path in ibmvnic_open
Nathan Fontenot [Thu, 30 Mar 2017 06:49:29 +0000 (02:49 -0400)]
ibmvnic: Cleanup failure path in ibmvnic_open

Now that ibmvnic_release_resources will clean up all of our resources
properly, even if they were not allocated, we can just call this
for failues in ibmvnic_open.

This patch also moves the ibmvnic_release_resources() routine up
in the file to avoid creating a forward declaration ad re-names it to
drop the ibmvnic prefix.

Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoibmvnic: Create init/release routines for stats token
Nathan Fontenot [Thu, 30 Mar 2017 06:49:23 +0000 (02:49 -0400)]
ibmvnic: Create init/release routines for stats token

Create an initialization and a release routine for the stats token used by
the ibmvnic driver.

Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoibmvnic: Merge the two release_sub_crq_queue routines
Nathan Fontenot [Thu, 30 Mar 2017 06:49:18 +0000 (02:49 -0400)]
ibmvnic: Merge the two release_sub_crq_queue routines

Keeping two routines for releasing sub crqs, one for when irqs are not
initialized and one for when they are, is a bit of overkill. Merge the
two routines to a common release routine that will check for an irq
and release it if needed.

Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoibmvnic: Create init and release routines for the rx pool
Nathan Fontenot [Thu, 30 Mar 2017 06:49:12 +0000 (02:49 -0400)]
ibmvnic: Create init and release routines for the rx pool

Move the initialization and the release of the rx pool to their own
routines, and update them to do validation.

Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoibmvnic: Create init and release routines for the tx pool
Nathan Fontenot [Thu, 30 Mar 2017 06:49:06 +0000 (02:49 -0400)]
ibmvnic: Create init and release routines for the tx pool

Move the initialization and the release of the tx pool to their own routines,
and update them to do validation. This also adds validation to the release
of the long term buffer.

Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoibmvnic: Create init and release routines for the bounce buffer
Nathan Fontenot [Thu, 30 Mar 2017 06:49:00 +0000 (02:49 -0400)]
ibmvnic: Create init and release routines for the bounce buffer

Move the handling of initialization and releasing the bounce buffer to their
own init and release routines.

Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoibmvnic: Update main crq initialization and release
Nathan Fontenot [Thu, 30 Mar 2017 06:48:54 +0000 (02:48 -0400)]
ibmvnic: Update main crq initialization and release

Update the initialization and release routines for the crq queue so that
we validate the crq queue.

Additionally this updates the naming of the init and release routines
for the crq queue to drop the ibmvnic prefix. This matches the naming
for similar routines in the driver

Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonet: tcp: Refine the __tcp_select_window
Gao Feng [Wed, 29 Mar 2017 22:49:19 +0000 (06:49 +0800)]
net: tcp: Refine the __tcp_select_window

1. Move the "window = tp->rcv_wnd;" into the condition block without
tp->rx_opt.rcv_wscale.
Because it is unnecessary when enable wscale;

2. Use the macro ALIGN instead of two statements.
The two statements are used to make window align to 1<<wscale.
Use the ALIGN is more clearer.

3. Use the rounddown to make codes clearer.

Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonet: dsa: mv88e6xxx: debug ATU Age Time
Vivien Didelot [Wed, 29 Mar 2017 19:38:37 +0000 (15:38 -0400)]
net: dsa: mv88e6xxx: debug ATU Age Time

The ATU ageing time value programmed in the switch is rounded up to the
nearest multiple of its coefficient (variable depending on the model.)

Add a debug message to inform the user about the exact programmed value.

On 6352, "brctl setageing br0 18" gives "AgeTime set to 0x01 (15000 ms)"
while on 6390 we get "AgeTime set to 0x05 (18750 ms)".

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoibmvnic: Remove debugfs support
Nathan Fontenot [Wed, 29 Mar 2017 19:14:55 +0000 (15:14 -0400)]
ibmvnic: Remove debugfs support

The debugfs support in the ibmvnic driver is not, and never has been,
supported. Just remove it.

The work done in the debugfs code for the driver was part of the original
spec for the ibmvnic driver. The corresponding support for this from the
server side was never supported and has been dropped.

Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agobonding: refine bond_fold_stats() wrap detection
Eric Dumazet [Wed, 29 Mar 2017 17:45:44 +0000 (10:45 -0700)]
bonding: refine bond_fold_stats() wrap detection

Some device drivers reset their stats at down/up events, possibly
fooling bonding stats, since they operate with relative deltas.

It is nearly not possible to fix drivers, since some of them compute the
tx/rx counters based on per rx/tx queue stats, and the queues can be
reconfigured (ethtool -L) between the down/up sequence.

Lets avoid accumulating 'negative' values that render bonding stats
useless.

It is better to lose small deltas, assuming the bonding stats are
fetched at a reasonable frequency.

Fixes: 5f0c5f73e5ef ("bonding: make global bonding stats more reliable")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoVSOCK: remove unnecessary ternary operator on return value
Colin Ian King [Wed, 29 Mar 2017 15:33:55 +0000 (16:33 +0100)]
VSOCK: remove unnecessary ternary operator on return value

Rather than assign the positive errno values to ret and then
checking if it is positive and flip the sign, just return the
errno value.

Detected by CoverityScan, CID#986649 ("Logically Dead Code")

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agodrivers: add explicit interrupt.h includes
Florian Westphal [Wed, 29 Mar 2017 15:17:31 +0000 (17:17 +0200)]
drivers: add explicit interrupt.h includes

These files all use functions declared in interrupt.h, but currently rely
on implicit inclusion of this file (via netns/xfrm.h).

That won't work anymore when the flow cache is removed so include that
header where needed.

Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonet: stmmac: dwmac-rk: Add handling for RGMII_ID/RXID/TXID
Wadim Egorov [Wed, 29 Mar 2017 12:12:19 +0000 (14:12 +0200)]
net: stmmac: dwmac-rk: Add handling for RGMII_ID/RXID/TXID

ATM dwmac-rk will always set and enable it's internal delay lines.
Using PHY internal delays in combination with the phy-mode
rgmii-id/rxid/txid was not possible. Only rgmii was supported.

Now we can disable rockchip's gmac delay lines and also use
rgmii-id/rxid/txid.

Tested only with a RK3288 based board.

Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoRevert "net: stmmac: enable multiple buffers"
LABBE Corentin [Wed, 29 Mar 2017 05:05:40 +0000 (07:05 +0200)]
Revert "net: stmmac: enable multiple buffers"

The commit aff3d9eff843 ("net: stmmac: enable multiple buffers") breaks
numerous boards. while some patch exists for fixing some of it,
dwmac-sunxi is still broken with it.
Since this patch is very huge, it will be better to split it in smaller
part.

Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoMerge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next...
David S. Miller [Wed, 29 Mar 2017 21:13:09 +0000 (14:13 -0700)]
Merge branch '40GbE' of git://git./linux/kernel/git/jkirsher/next-queue

Jeff Kirsher says:

====================
40GbE Intel Wired LAN Driver Updates 2017-03-29

This series contains updates to i40e and i40evf only.

Preethi changes the default driver mode of operation to descriptor
write-back for VF.

Alex cleans up and addresses several issues in the way that i40e handles
private flags.  Modifies the driver to use the length of the packet
instead of the DD status bit to determine if a new descriptor is ready
to be processed.  Refactors the driver by pulling the code responsible
for fetching the receive buffer and synchronizing DMA into a single
function.  Also pulled the code responsible for handling buffer
recycling and page counting and distributed it through several functions,
so we can commonize the bits that handle either freeing or recycling the
buffers.  Cleans up the code in preparation for us adding support for
build_skb().  Changed the way we handle the maximum frame size for the
receive path so it is more consistent with other drivers.

Paul enables XL722 to use the direct read/write method since it does not
support the AQ command to read/write the control register.

Christopher fixes a case where we miss an arq element if a new one is
added before we enable interrupts and exit the loop.

Jake cleans up a pointless goto statement.  Also cleaned up a flag that
was not being used.

Carolyn does round 2 for adding a delay to the receive queue to
accommodate the hardware needs.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoMerge branch 'tipc-socketpair'
David S. Miller [Wed, 29 Mar 2017 21:10:12 +0000 (14:10 -0700)]
Merge branch 'tipc-socketpair'

Parthasarathy Bhuvaragan says:

====================
tipc: add socketpair support

We add socketpair support for connection oriented sockets in
the first patch and for connection less in the second.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agotipc: allow rdm/dgram socketpairs
Erik Hugne [Wed, 29 Mar 2017 09:22:17 +0000 (11:22 +0200)]
tipc: allow rdm/dgram socketpairs

for socketpairs using connectionless transport, we cache
the respective node local TIPC portid to use in subsequent
calls to send() in the socket's private data.

Signed-off-by: Erik Hugne <erik.hugne@gmail.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agotipc: add support for stream/seqpacket socketpairs
Erik Hugne [Wed, 29 Mar 2017 09:22:16 +0000 (11:22 +0200)]
tipc: add support for stream/seqpacket socketpairs

sockets A and B are connected back-to-back, similar to what
AF_UNIX does.

Signed-off-by: Erik Hugne <erik.hugne@gmail.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonet: mvneta: set rx mode during resume if interface is running
Jisheng Zhang [Wed, 29 Mar 2017 08:47:19 +0000 (16:47 +0800)]
net: mvneta: set rx mode during resume if interface is running

I found a bug by:

0. boot and start dhcp client
1. echo mem > /sys/power/state
2. resume back immediately
3. don't touch dhcp client to renew the lease
4. ping the gateway. No acks

Usually, after step2, the DHCP lease isn't expired, so in theory we
should resume all back. But in fact, it doesn't. It turns out
the rx mode isn't resumed correctly. This patch fixes it by adding
mvneta_set_rx_mode(dev) in the resume hook if interface is running.

Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonet: mvneta: add RGMII_RXID and RGMII_TXID support
Jisheng Zhang [Wed, 29 Mar 2017 08:42:26 +0000 (16:42 +0800)]
net: mvneta: add RGMII_RXID and RGMII_TXID support

RGMII_RXID and RGMII_TX_ID share the same GMAC CTRL setting as RGMII
or RGMII_ID.

Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonet: veth: use new api ethtool_{get|set}_link_ksettings
Philippe Reynes [Wed, 29 Mar 2017 06:24:21 +0000 (08:24 +0200)]
net: veth: use new api ethtool_{get|set}_link_ksettings

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.

Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoMerge tag 'mlx5e-pedit' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
David S. Miller [Wed, 29 Mar 2017 18:24:21 +0000 (11:24 -0700)]
Merge tag 'mlx5e-pedit' of git://git./linux/kernel/git/saeed/linux

Or Gerlitz says:

====================
mlx5e-pedit 2017-03-28

This series adds support for offloading modifications of packet headers using
ConnectX-5 HW header re-write as an action applied during packet steering.

The offloaded SW mechanism is TC's pedit action. The offloading is
supported for E-Switch steering of VF traffic in the SRIOV
switchdev mode and for NIC (non eswitch) RX.

One use-case for this offload on virtual networks, is when the hypervisor
implements flow based router such as Open-Stack's DVR, where L2 headers
of guest packets re-written with routers' MAC addresses and the IP TTL
is decremented.

Another use case (which can be applied in parallel with routing) is
stateless NAT where guest L3/L4 headers are re-written.

The series is built as follows: the 1st six patches are preperations which
don't yet add new functionality, patches 7-8 add the FW APIs (data-structures
and commands) for header re-write, and patch nine allows offloading driver
to access pedit keys.

The 10th patch is somehow the core of the series, where we translate from
the pedit way to represent set of header modification elements to the FW
API for that same matter.

Once a set of HW modification is established, we register it with the FW
and get a modify header ID. When this ID is used with an action during
packet steering, the HW applies the header modification on the packet.

Patches 11 and 12 implement the above logic as an offload for pedit action
for the NIC and E-Switch use-cases.

I'd like to thanks Elijah Shakkour <elijahs@mellanox.com> for implementing
and helping me testing this functionality on HW simulator, before it could
be done with FW.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonet: mpls: Update lfib_nlmsg_size to skip deleted nexthops
David Ahern [Tue, 28 Mar 2017 22:19:49 +0000 (15:19 -0700)]
net: mpls: Update lfib_nlmsg_size to skip deleted nexthops

A recent commit skips nexthops in a route if the device has been
deleted. Update lfib_nlmsg_size accordingly.

Reported-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonet: phy: Allow building mdio-boardinfo into the kernel
Florian Fainelli [Tue, 28 Mar 2017 19:57:09 +0000 (12:57 -0700)]
net: phy: Allow building mdio-boardinfo into the kernel

mdio-boardinfo contains code that is helpful for platforms to register
specific MDIO bus devices independent of how CONFIG_MDIO_DEVICE or
CONFIG_PHYLIB will be selected (modular or built-in). In order to make
that possible, let's do the following:

- descend into drivers/net/phy/ unconditionally

- make mdiobus_setup_mdiodev_from_board_info() take a callback argument
  which allows us not to expose the internal MDIO board info list and
  mutex, yet maintain the logic within the same file

- relocate the code that creates a MDIO device into
  drivers/net/phy/mdio_bus.c

- build mdio-boardinfo.o into the kernel as soon as MDIO_DEVICE is
  defined (y or m)

Fixes: 90eff9096c01 ("net: phy: Allow splitting MDIO bus/device support from PHYs")
Fixes: 648ea0134069 ("net: phy: Allow pre-declaration of MDIO devices")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoi40e: fix for queue timing delays
Wyborny, Carolyn [Tue, 28 Mar 2017 15:00:48 +0000 (08:00 -0700)]
i40e: fix for queue timing delays

This patch adds a delay to Rx queue disables to accommodate HW needs.

v2: Added missing check for disable only, additional details on the
need for the ugly delay and fixed spacing on comment.

Change-ID: I2864ca667ce5dcc2cc44f8718113b719742a46a1
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
7 years agoi40e/i40evf: Change the way we limit the maximum frame size for Rx
Alexander Duyck [Tue, 14 Mar 2017 17:15:27 +0000 (10:15 -0700)]
i40e/i40evf: Change the way we limit the maximum frame size for Rx

This patch changes the way we handle the maximum frame size for the Rx
path.  Previously we were rounding up to 2K for a 1500 MTU and then brining
the max frame size down to MTU plus a fixed amount.  With this patch
applied what we now do is limit the maximum frame to 1.5K minus the value
for NET_IP_ALIGN for standard MTU, and for any MTU greater than 1500 we
allow up to the maximum frame size.  This makes the behavior more
consistent with the other drivers such as igb which had similar logic.  In
addition it reduces the test matrix for MTU since we only have two max
frame sizes that are handled for Rx now.

Change-ID: I23a9d3c857e7df04b0ef28c64df63e659c013f3f
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
7 years agoi40e/i40evf: Add legacy-rx private flag to allow fallback to old Rx flow
Alexander Duyck [Tue, 14 Mar 2017 17:15:26 +0000 (10:15 -0700)]
i40e/i40evf: Add legacy-rx private flag to allow fallback to old Rx flow

This patch adds a control which will allow us to toggle into and out of the
legacy Rx mode.  The legacy Rx mode is what we currently do when performing
Rx.  As I make further changes what should happen is that the driver will
fall back to the behavior for Rx as of this patch should the "legacy-rx"
flag be set to on.

Change-ID: I0342998849bbb31351cce05f6e182c99174e7751
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
7 years agoi40e/i40evf: Break i40e_fetch_rx_buffer up to allow for reuse of frag code
Alexander Duyck [Tue, 14 Mar 2017 17:15:25 +0000 (10:15 -0700)]
i40e/i40evf: Break i40e_fetch_rx_buffer up to allow for reuse of frag code

This patch is meant to clean up the code in preparation for us adding
support for build_skb.  Specifically we deconstruct i40e_fetch_buffer into
several functions so that those functions can later be reused when we add a
path for build_skb.

Specifically with this change we split out the code for adding a page to an
exiting skb.

Change-ID: Iab1efbab6b8b97cb60ab9fdd0be1d37a056a154d
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
7 years agoi40e/i40evf: Pull out code for cleaning up Rx buffers
Alexander Duyck [Tue, 14 Mar 2017 17:15:24 +0000 (10:15 -0700)]
i40e/i40evf: Pull out code for cleaning up Rx buffers

This patch pulls out the code responsible for handling buffer recycling and
page counting and distributes it through several functions.  This allows us
to commonize the bits that handle either freeing or recycling the buffers.

As far as the page count tracking one change to the logic is that
pagecnt_bias is decremented as soon as we call i40e_get_rx_buffer.  It is
then the responsibility of the function that pulls the data to either
increment the pagecnt_bias if the buffer can be recycled as-is, or to
update page_offset so that we are pointing at the correct location for
placement of the next buffer.

Change-ID: Ibac576360cb7f0b1627f2a993d13c1a8a2bf60af
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
7 years agoi40e/i40evf: Pull code for grabbing and syncing rx_buffer from fetch_buffer
Alexander Duyck [Tue, 14 Mar 2017 17:15:23 +0000 (10:15 -0700)]
i40e/i40evf: Pull code for grabbing and syncing rx_buffer from fetch_buffer

This patch pulls the code responsible for fetching the Rx buffer and
synchronizing DMA into a function, specifically called i40e_get_rx_buffer.

The general idea is to allow for better code reuse by pulling this out of
i40e_fetch_rx_buffer.  We dropped a couple of prefetches since the time
between the prefetch being called and the data being accessed was too small
to be useful.

Change-ID: I4885fce4b2637dbedc8e16431169d23d3d7e79b9
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
7 years agoi40e/i40evf: Use length to determine if descriptor is done
Alexander Duyck [Tue, 14 Mar 2017 17:15:22 +0000 (10:15 -0700)]
i40e/i40evf: Use length to determine if descriptor is done

This change makes it so that we use the length of the packet instead of the
DD status bit to determine if a new descriptor is ready to be processed.
The obvious advantage is that it cuts down on reads as we don't really even
need the DD bit if going from a 0 to a non-zero value on size is enough to
inform us that the packet has been completed.

Change-ID: Iebdf9cdb36c454ef092df27199b92ad09c374231
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
7 years agoi40e: remove FDIR_REQUIRES_REINIT driver flag
Jacob Keller [Fri, 10 Mar 2017 20:22:05 +0000 (12:22 -0800)]
i40e: remove FDIR_REQUIRES_REINIT driver flag

This flag hasn't been used since commit 1e1be8f622ee ("i40e: ATR policy
change to flush the table to clean stale ATR rules").

Lets simplify things and just remove it.

Change-ID: I76279d84db8a2fd96f445b96aa413059f9256879
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
7 years agoi40e: remove a useless goto statement
Jacob Keller [Fri, 10 Mar 2017 20:22:04 +0000 (12:22 -0800)]
i40e: remove a useless goto statement

The goto found here for when in MFP mode is pointless. It jumps to the
end of a series of if blocks. However, right after this statement is
a closing '}' for this if block, which will result in the program flow
going to the exact same location as the goto statement indicates. Thus,
regardless of whether we are in MFP mode, the program flow will resume
from the same location.

This arose due to various refactoring which did not notice that this
goto became essentially a no-op.

To properly understand this diff you will need to view a larger context
than is given by default.

Change-ID: I088f73c3831aa5c4e2281380c7a3ce605594300c
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
7 years agoi40e: Check for new arq elements before leaving the adminq subtask loop
Christopher N Bednarz [Fri, 10 Mar 2017 20:22:03 +0000 (12:22 -0800)]
i40e: Check for new arq elements before leaving the adminq subtask loop

Fix a case where we miss an arq element if a new one is added before we
enable interrupts and exit the arq subtask loop. This occurs frequently
with RDMA running on Windows VF and causes long delays that prevent SMB
from establishing connections.

Change-ID: I3e1c8b2b960c12857d9b8275bea2c1563674392e
Signed-off-by: Christopher N Bednarz <christopher.n.bednarz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
7 years agoi40e: use register for XL722 control register read/write
Paul M Stillwell Jr [Fri, 10 Mar 2017 20:22:02 +0000 (12:22 -0800)]
i40e: use register for XL722 control register read/write

The XL722 doesn't support the AQ command to read/write the control
register so enable it to bypass the check and use the direct read/write
method.

Change-ID: Iefecc737b57207485c90845af5989d5af518bf16
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
7 years agoi40e: Clean up handling of private flags
Alexander Duyck [Fri, 10 Mar 2017 20:22:01 +0000 (12:22 -0800)]
i40e: Clean up handling of private flags

This patch cleans up and addresses several issues in the way that i40e
handles private flags. Previously the code was choosing fixed bits and
trying to match them up with strings in a somewhat haphazard way. This
resulted in the possibility for adding a new bit and causing a mismatch as
the private flags are linear bits starting at 0, and the private flags in
the driver were split up over a group specific to the PF and a group that
was global.

What this change does is define an array of structs used to represent the
private flags. Contained within the structs are the bits necessary to know
which flags to set and/or clear depending on the state of the bit. By
doing this we can add new bits in the future with minimal overhead and
avoid creating possible mis-matches should we need to remove a flag based
on compile options.

Change-ID: Ia3214ab04f0ab2f70354ac0997a135f1d01b0acd
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
7 years agoi40evf: enforce descriptor write-back mechanism for VF
Preethi Banala [Fri, 10 Mar 2017 20:22:00 +0000 (12:22 -0800)]
i40evf: enforce descriptor write-back mechanism for VF

The current driver mode is to use a write-back mechanism for the head
register which indicates transmit completions. The VF driver needs to be
able to work on hardware that exclusively uses descriptor write-back, so
change the default driver mode of operation to descriptor write-back for
VF. In our analysis, performance wasn't significantly different with
either write-back method.

Change-ID: Ia92e4ec77c2df8dc4515c71d53746d57d77759af
Signed-off-by: Preethi Banala <preethi.banala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
7 years agoMerge branch 'dsa-devlink'
David S. Miller [Wed, 29 Mar 2017 05:46:05 +0000 (22:46 -0700)]
Merge branch 'dsa-devlink'

Andrew Lunn says:

====================
break include loop and dsa devlink support

These two patches add very basic support for devlink to DSA, in
preparation for playing with dpipe.

The first patch is needed to break an include loop between
netdevice.h, dsa.h and devlink.h. We need to remove dsa.h from
netdevice.h. As a result, some files fail to compile, because they
require includes pulled in via dsa.h. So this patch adds a number of
includes in various places. The majority is within the network
subsystem, but cifs also needs a few fixes.

0-day has been chewing on this for over a day now, and not found any
breakage. But Arnd's randconfig might uncover something.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonet: dsa: dsa2: Add basic support of devlink
Andrew Lunn [Tue, 28 Mar 2017 21:45:07 +0000 (23:45 +0200)]
net: dsa: dsa2: Add basic support of devlink

Register the switch and its ports with devlink.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonet: break include loop netdevice.h, dsa.h, devlink.h
Andrew Lunn [Tue, 28 Mar 2017 21:45:06 +0000 (23:45 +0200)]
net: break include loop netdevice.h, dsa.h, devlink.h

There is an include loop between netdevice.h, dsa.h, devlink.h because
of NETDEV_ALIGN, making it impossible to use devlink structures in
dsa.h.

Break this loop by taking dsa.h out of netdevice.h, add a forward
declaration of dsa_switch_tree and netdev_set_default_ethtool_ops()
function, which is what netdevice.h requires.

No longer having dsa.h in netdevice.h means the includes in dsa.h no
longer get included. This breaks a few other files which depend on
these includes. Add these directly in the affected file.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoMerge branch 'netconf-delnetconf'
David S. Miller [Wed, 29 Mar 2017 05:32:43 +0000 (22:32 -0700)]
Merge branch 'netconf-delnetconf'

David Ahern says:

====================
netconf: Add support for RTM_DELNETCONF

netconf notifications are sent as devices register but not when they
are deleted leaving userspace caches out of sync. Add support for
RTM_DELNETCONF to ipv4, ipv6 and mpls.

MPLS is missing RTM_NEWNETCONF as devices are created, so add it as well.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonet: mpls: Send netconf messages on device register and unregister
David Ahern [Tue, 28 Mar 2017 21:28:07 +0000 (14:28 -0700)]
net: mpls: Send netconf messages on device register and unregister

Send netconf notifications for MPLS when the device registers and
unregisters.

Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonet:mpls: Refactor mpls_netconf_notify_devconf to take event
David Ahern [Tue, 28 Mar 2017 21:28:06 +0000 (14:28 -0700)]
net:mpls: Refactor mpls_netconf_notify_devconf to take event

Refactor mpls_netconf_notify_devconf to take the event as an input arg.

Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonet: ipv6: Add support for RTM_DELNETCONF
David Ahern [Tue, 28 Mar 2017 21:28:05 +0000 (14:28 -0700)]
net: ipv6: Add support for RTM_DELNETCONF

Send RTM_DELNETCONF notifications when a device is deleted. The message only
needs the device index, so modify inet6_netconf_fill_devconf to skip devconf
references if it is NULL.

Allows a userspace cache to remove entries as devices are deleted.

Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonet: ipv6: Refactor inet6_netconf_notify_devconf to take event
David Ahern [Tue, 28 Mar 2017 21:28:04 +0000 (14:28 -0700)]
net: ipv6: Refactor inet6_netconf_notify_devconf to take event

Refactor inet6_netconf_notify_devconf to take the event as an input arg.

Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonet: devinet: Add support for RTM_DELNETCONF
David Ahern [Tue, 28 Mar 2017 21:28:03 +0000 (14:28 -0700)]
net: devinet: Add support for RTM_DELNETCONF

Send RTM_DELNETCONF notifications when a device is deleted. The message only
needs the device index, so modify inet_netconf_fill_devconf to skip devconf
references if it is NULL.

Allows a userspace cache to remove entries as devices are deleted.

Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonet: devinet: Refactor inet_netconf_notify_devconf to take event
David Ahern [Tue, 28 Mar 2017 21:28:02 +0000 (14:28 -0700)]
net: devinet: Refactor inet_netconf_notify_devconf to take event

Refactor inet_netconf_notify_devconf to take the event as an input arg.

Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agortnetlink: Add RTM_DELNETCONF
David Ahern [Tue, 28 Mar 2017 21:28:01 +0000 (14:28 -0700)]
rtnetlink: Add RTM_DELNETCONF

Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoliquidio: refactor interrupt moderation code
Prasad Kanneganti [Tue, 28 Mar 2017 19:14:06 +0000 (12:14 -0700)]
liquidio: refactor interrupt moderation code

Refactor interrupt moderation code for flexibility because parameters are
different for 10G and 25G cards.  Currently parameters (for 10G only) come
from macros compiled-in to the PF and VF drivers; fix it so that parameters
suitable for the card (10G or 25G) come from the NIC firmware via response
to a command.

Also bump up driver version to 1.5.1 to match newer NIC firmware version.

Signed-off-by: Prasad Kanneganti <prasad.kanneganti@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonet: dsa: fix copyright holder
Vivien Didelot [Tue, 28 Mar 2017 19:10:36 +0000 (15:10 -0400)]
net: dsa: fix copyright holder

I do not hold the copyright of the DSA core and drivers source files,
since these changes have been written as an initiative of my day job.
Fix this.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonet: dsa: mv88e6xxx: unconditionally set ATU trunk
Vivien Didelot [Tue, 28 Mar 2017 19:09:43 +0000 (15:09 -0400)]
net: dsa: mv88e6xxx: unconditionally set ATU trunk

Set the trunk member of the mv88e6xxx_atu_entry structure regardless its
value, so that uninitialized structures gets the correct boolean value.

Note that no mainline code is affected by the current behavior.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoipv6: add support for NETDEV_RESEND_IGMP event
Vlad Yasevich [Tue, 28 Mar 2017 18:49:16 +0000 (14:49 -0400)]
ipv6: add support for NETDEV_RESEND_IGMP event

This patch adds support for NETDEV_RESEND_IGMP event similar
to how it works for IPv4.

Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoMerge branch 'dsa-mv88e6xxx-fix-chip-definitions'
David S. Miller [Wed, 29 Mar 2017 04:52:53 +0000 (21:52 -0700)]
Merge branch 'dsa-mv88e6xxx-fix-chip-definitions'

Vivien Didelot says:

====================
net: dsa: fix chip definitions

The definitions of some of the mv88e6xxx_ops and mv88e6xxx_info
structures are misordered and erroneous for 88E6191 and 88E6391.

This patch series cleans that up.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonet: dsa: mv88e6xxx: remove 88E6391 ops
Vivien Didelot [Tue, 28 Mar 2017 17:50:35 +0000 (13:50 -0400)]
net: dsa: mv88e6xxx: remove 88E6391 ops

We don't support 88E6391 anywhere in the code, so remove the unused
mv88e6391_ops structure.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonet: dsa: mv88e6xxx: fix 88E6191 ops
Vivien Didelot [Tue, 28 Mar 2017 17:50:34 +0000 (13:50 -0400)]
net: dsa: mv88e6xxx: fix 88E6191 ops

The mv88e6xxx_info structure for the 88E6191 chip was pointing the
mv88e6391_ops definition instead of mv88e6191_ops. Fix this.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonet: dsa: mv88e6xxx: reorder 88E6341 definitions
Vivien Didelot [Tue, 28 Mar 2017 17:50:33 +0000 (13:50 -0400)]
net: dsa: mv88e6xxx: reorder 88E6341 definitions

The related mv88e6xxx_ops structure was misplaced. Reorder it correctly
to fix this.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonet: dsa: mv88e6xxx: reorder 88E6141 definitions
Vivien Didelot [Tue, 28 Mar 2017 17:50:32 +0000 (13:50 -0400)]
net: dsa: mv88e6xxx: reorder 88E6141 definitions

The related mv88e6xxx_ops and mv88e6xxx_info structure were misplaced.
Reorder them correctly to fix this.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoMerge branch 'qed-load-unload-mfw'
David S. Miller [Wed, 29 Mar 2017 01:05:24 +0000 (18:05 -0700)]
Merge branch 'qed-load-unload-mfw'

Yuval Mintz says:

====================
qed: load/unload mfw series

This series correct the unload flow and greatly enhances its
initialization flow in regard to interactions between driver
and management firmware.

Patch #1 makes sure unloading is done under management-firmware's
'criticial section' protection.

Patches #2 - #4 move driver into using a newer scheme for loading
in regard to the MFW; This newer scheme would help cleaning the device
in case a previous instance has dirtied it [preboot, PDA, etc.].

Patches #5 - #6 let driver inform management-firmware on number of
resources which are dependent on the non-management firmware used.
Patch #7 then uses a new resource [BDQ] instead of some set value.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoqed: Use BDQ resource for storage protocols
Mintz, Yuval [Tue, 28 Mar 2017 12:12:56 +0000 (15:12 +0300)]
qed: Use BDQ resource for storage protocols

Until now, qed used some port-defined value as BDQ index for both iSCSI
and FCoE.

As management firmware now treats BDQ as a resource and tells each PF
its BDQ-range, start using a valure from that range instead.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoqed: Utilize resource-lock based scheme
Tomer Tayar [Tue, 28 Mar 2017 12:12:55 +0000 (15:12 +0300)]
qed: Utilize resource-lock based scheme

Management firmware is used as an arbiter between the various PFs
in matters of resources, but some of the resources that need to
be divided are dependent on the non-management firmware used,
so management firmware first needs to be told how many resources
there are before trying to divide them.

As part of the initialization sequence, driver would first inform
the management firmware of the available resources under
a dedicated resource lock, and afterwards request for various
resources which might be based on the previous set values.

Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoqed: Support management-based resource locking
Tomer Tayar [Tue, 28 Mar 2017 12:12:54 +0000 (15:12 +0300)]
qed: Support management-based resource locking

Global locking can't properly be used to synchronize between different
PFs in all scenarios, as those instances might reside in different
logical partitions [e.g., when a PF is assigned via PDA to some VM].

The management firmware provides a generic infrastructure for
device locks. For each 'resource', it's guaranteed it could be acquired
by at most a single PF at any given time [or by management firmware].

This patch adds the necessary logic in qed for utilizing said
infrastructure, implementing lock/unlock internal APIs.

Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoqed: Send pf-flr as part of initialization
Mintz, Yuval [Tue, 28 Mar 2017 12:12:53 +0000 (15:12 +0300)]
qed: Send pf-flr as part of initialization

During HW initialization, driver would set various registers to their
needed values - but it assumes all registers start at their reset-value,
so there's no need to re-configure a register's default value.

This assumption might be incorrect, e.g., in case of preboot driver
running and initializing the driver prior to our driver.

To overcome this, we now ask management firmware to initiate a PF-flr
early during the initialization sequence. That would return everything
in the PF's scope back to default and prevent previous configurations
from still being applied.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoqed: Move to new load request scheme
Tomer Tayar [Tue, 28 Mar 2017 12:12:52 +0000 (15:12 +0300)]
qed: Move to new load request scheme

Management firmware is used as an arbiter between the various PFs
in regard to loading - it causes the various PFs to load/unload
sequentially and informs each of its appropriate rule in the init.

But the existing flow is too weak to handle some scenarios where
PFs aren't properly cleaned prior to loading.
The significant scenarios falling under this criteria:
  a. Preboot drivers in some environment can't properly unload.
  b. Unexpected driver replacement [kdump, PDA].

Modern management firmware supports a more intricate loading flow,
where the driver has the ability to overcome previous limitations.
This moves qed into using this newer scheme.

Notice new scheme is backward compatible, so new drivers would
still be able to load properly on top of older management firmwares
and vice versa.

Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoqed: hw_init() to receive parameter-struct
Mintz, Yuval [Tue, 28 Mar 2017 12:12:51 +0000 (15:12 +0300)]
qed: hw_init() to receive parameter-struct

We'll soon need additional information, so start by changing
the infrastructure to receive the initializing variables
via a parameter struct.

Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoqed: Correct HW stop flow
Tomer Tayar [Tue, 28 Mar 2017 12:12:50 +0000 (15:12 +0300)]
qed: Correct HW stop flow

Management firmware is used as arbiter between different PFs
which are loading/unloading, but in order to use the synchronization
it offers the contending configurations need to be applied either
between their LOAD_REQ <-> LOAD_DONE or UNLOAD_REQ <-> UNLOAD_DONE
management firmware commands.

Existing HW stop flow utilizes 2 different functions: qed_hw_stop() and
qed_hw_reset() which don't abide this requirement; Most of the closure
is doing outside the scope of the unload request.

This patch removes qed_hw_reset() and places the relevant stop
functionality underneath the management firmware protection.

Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoMerge branch 'tipc-subscription-refcount-simplifications'
David S. Miller [Wed, 29 Mar 2017 01:03:33 +0000 (18:03 -0700)]
Merge branch 'tipc-subscription-refcount-simplifications'

Parthasarathy Bhuvaragan says:

====================
tipc: subscription refcount simplifications

The first patch makes the subscription refcount cleanup lockless and
the second updates the subscription refcount policy.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agotipc: adjust the policy of holding subscription kref
Ying Xue [Tue, 28 Mar 2017 10:28:28 +0000 (12:28 +0200)]
tipc: adjust the policy of holding subscription kref

When a new subscription object is inserted into name_seq->subscriptions
list, it's under name_seq->lock protection; when a subscription is
deleted from the list, it's also under the same lock protection;
similarly, when accessing a subscription by going through subscriptions
list, the entire process is also protected by the name_seq->lock.

Therefore, if subscription refcount is increased before it's inserted
into subscriptions list, and its refcount is decreased after it's
deleted from the list, it will be unnecessary to hold refcount at all
before accessing subscription object which is obtained by going through
subscriptions list under name_seq->lock protection.

Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agotipc: advance the time of deleting subscription from subscriber->subscrp_list
Ying Xue [Tue, 28 Mar 2017 10:28:27 +0000 (12:28 +0200)]
tipc: advance the time of deleting subscription from subscriber->subscrp_list

After a subscription object is created, it's inserted into its
subscriber subscrp_list list under subscriber lock protection,
similarly, before it's destroyed, it should be first removed from
its subscriber->subscrp_list. Since the subscription list is
accessed with subscriber lock, all the subscriptions are valid
during the lock duration. Hence in tipc_subscrb_subscrp_delete(), we
remove subscription get/put and the extra subscriber unlock/lock.

After this change, the subscriptions refcount cleanup is very simple
and does not access any lock.

Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agostmmac: use netif_set_real_num_{rx,tx}_queues
Arnd Bergmann [Tue, 28 Mar 2017 09:48:21 +0000 (11:48 +0200)]
stmmac: use netif_set_real_num_{rx,tx}_queues

A driver must not access the two fields directly but should instead use
the helper functions to set the values and keep a consistent internal
state:

ethernet/stmicro/stmmac/stmmac_main.c: In function 'stmmac_dvr_probe':
ethernet/stmicro/stmmac/stmmac_main.c:4083:8: error: 'struct net_device' has no member named 'real_num_rx_queues'; did you mean 'real_num_tx_queues'?

Fixes: a8f5102af2a7 ("net: stmmac: TX and RX queue priority configuration")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agosoc: qcom: smd-rpm: Add msm8996 compatibility
Bjorn Andersson [Tue, 28 Mar 2017 05:26:35 +0000 (22:26 -0700)]
soc: qcom: smd-rpm: Add msm8996 compatibility

With the RPM driver transitioned to RPMSG we can reuse the SMD-RPM
driver ontop of GLINK for 8996, without any modifications.

Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agosoc: qcom: smd: Remove standalone driver
Bjorn Andersson [Tue, 28 Mar 2017 05:26:34 +0000 (22:26 -0700)]
soc: qcom: smd: Remove standalone driver

Remove the standalone SMD implementation as we have transitioned the
client drivers to use the RPMSG based one.

Also remove all dependencies on QCOM_SMD from Kconfig files, in order to
keep them selectable in the absence of the removed symbol.

Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agosoc: qcom: smd: Transition client drivers from smd to rpmsg
Bjorn Andersson [Tue, 28 Mar 2017 05:26:33 +0000 (22:26 -0700)]
soc: qcom: smd: Transition client drivers from smd to rpmsg

By moving these client drivers to use RPMSG instead of the direct SMD
API we can reuse them ontop of the newly added GLINK wire-protocol
support found in the 820 and 835 Qualcomm platforms.

As the new (RPMSG-based) and old SMD implementations are mutually
exclusive we have to change all client drivers in one commit, to make
sure we have a working system before and after this transition.

Acked-by: Andy Gross <andy.gross@linaro.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agovxlan: don't age NTF_EXT_LEARNED fdb entries
Roopa Prabhu [Mon, 27 Mar 2017 22:46:41 +0000 (15:46 -0700)]
vxlan: don't age NTF_EXT_LEARNED fdb entries

vxlan driver already implicitly supports installing
of external fdb entries with NTF_EXT_LEARNED. This
patch just makes sure these entries are not aged
by the vxlan driver. An external entity managing these
entries will age them out. This is consistent with
the use of NTF_EXT_LEARNED in the bridge driver.

Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agoMerge branch 'net-dpipe'
David S. Miller [Wed, 29 Mar 2017 00:11:56 +0000 (17:11 -0700)]
Merge branch 'net-dpipe'

Jiri Pirko says:

====================
Add support for pipeline debug (dpipe)

Arkadi says:

While doing the hardware offloading process much of the hardware
specifics cannot be presented. An example for such is the routing
LPM algorithm which differ in hardware implementation from the
kernel software implementation. The only information the user receives
is whether specific route is offloaded or not, but he cannot really
understand the underlying implementation nor get the specific statistics
related to that process.

Another example is ACL offload using TC which is commonly implemented
using TCAM memory. Currently there is no capability to gain visibility
into the TCAM structure and to debug suboptimal resource allocation.

This patchset introduces capability for exporting the ASICs pipeline
abstraction via devlink infrastructure, which should serve as an
complementary tool. This infrastructure allows the user to get visibility
into the ASIC by modeling it as a set of match/action tables.

The main objects defined:
Table - abstraction for a single pipeline stage. Contains the
        available match/actions and counter availability.
Entry - entry in a specific table with specific matches/actions
        values and dedicated counter.
Header/field - tuples which describes the tables behavior.

As an example one of the ASIC's L3 blocks will be modeled. The egress
rif (router interface) table is the final step in the L3 pipeline
processing which does match on the internal rif index which was
determined before by the routing logic. The erif table determines
whether to forward or drop the packet and updates the corresponding
rif L3 statistics.

To expose this internal resources a special metadata header will
be introduced that describes the internal information gathered by
the ASIC's pipeline and contains the following fields: rif_port_index,
forward and drop.

Some internal hardware resources have direct mapping to kernel
objects. For example the rif_port_index is mapped to the net-devices
ifindex. By providing this mapping the users gains visibility into
the offloading process.

Follow-up work will include exporting more L3 tables which will give
visibility into the routing process.

First stage is adding support for dpipe in devlink. Next add support
in spectrum driver. Finally implement egress router interface
(erif) table for spectrum ASIC as an example.

---
v1->v2: Please see individual patches
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agomlxsw: spectrum: Add Support for erif table entries access
Arkadi Sharshevsky [Tue, 28 Mar 2017 15:24:17 +0000 (17:24 +0200)]
mlxsw: spectrum: Add Support for erif table entries access

Implement dpipe's table ops for erif table which provide:
1. Getting the entries in the table with the associate values.
- match on "mlxsw_meta:erif_index"
- action on "mlxsw_meta:forwared_out"
2. Synchronize the hardware in case of enabling/disabling counters which
   mean removing erif counters from all interfaces.

Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agomlxsw: spectrum_router: Add rif helper functions
Arkadi Sharshevsky [Tue, 28 Mar 2017 15:24:16 +0000 (17:24 +0200)]
mlxsw: spectrum_router: Add rif helper functions

Add rif helper function to access the rif index and rif devices ifindex.
This functions will be used by dpipe in order to dump the rif table.

Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agomlxsw: spectrum: Support for counters on router interfaces
Arkadi Sharshevsky [Tue, 28 Mar 2017 15:24:15 +0000 (17:24 +0200)]
mlxsw: spectrum: Support for counters on router interfaces

Add support for counter allocation on router interfaces. The allocation
depends on the counter state of relevant table. In case the counting is
disabled or no counters left the counter index will be set as invalid.

Also a counter pool for router allocation is added.

Signed-off-by: Arakdi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agomlxsw: reg: Add Router Interface Counter Register
Arkadi Sharshevsky [Tue, 28 Mar 2017 15:24:14 +0000 (17:24 +0200)]
mlxsw: reg: Add Router Interface Counter Register

The RICNT register retrieves per port performance counter. It will be
used to query the router interfaces statistics.

Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agomlxsw: spectrum: Add definition for egress rif table
Arkadi Sharshevsky [Tue, 28 Mar 2017 15:24:13 +0000 (17:24 +0200)]
mlxsw: spectrum: Add definition for egress rif table

Add definition for egress router interface table. This table describes
the final part in the routing pipeline. This table matches the egress
interface index (rif index, which is set by the previous stages and
determine the out port) and makes the decision of forwarding the packet
towards the L2 logic or dropping it.

The metadata header is added to represent this internal information.
The rif index field is mapped logically to netdevice ifindex.

Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agomlxsw: spectrum: Add placeholder for dpipe
Arkadi Sharshevsky [Tue, 28 Mar 2017 15:24:12 +0000 (17:24 +0200)]
mlxsw: spectrum: Add placeholder for dpipe

Add placeholder for dpipe. Support for specific tables and headers will
be introduced in following patches. The headers are shared between all
mlxsw_sp instances.

Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agomlxsw: reg: Add counter fields to RITR register
Arkadi Sharshevsky [Tue, 28 Mar 2017 15:24:11 +0000 (17:24 +0200)]
mlxsw: reg: Add counter fields to RITR register

Update RITR for counter support. This allows adding counters for
ASIC's router ports.

Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agodevlink: Support for pipeline debug (dpipe)
Arkadi Sharshevsky [Tue, 28 Mar 2017 15:24:10 +0000 (17:24 +0200)]
devlink: Support for pipeline debug (dpipe)

The pipeline debug is used to export the pipeline abstractions for the
main objects - tables, headers and entries. The only support for set is
for changing the counter parameter on specific table.

The basic structures:

Header - can represent a real protocol header information or internal
         metadata. Generic protocol headers like IPv4 can be shared
         between drivers. Each driver can add local headers.

Field - part of a header. Can represent protocol field or specific ASIC
        metadata field. Hardware special metadata fields can be mapped
        to different resources, for example switch ASIC ports can have
        internal number which from the systems point of view is mapped
        to netdeivce ifindex.

Match - represent specific match rule. Can describe match on specific
        field or header. The header index should be specified as well
        in order to support several header instances of the same type
        (tunneling).

Action - represents specific action rule. Actions can describe operations
         on specific field values for example like set, increment, etc.
         And header operation like add and delete.

Value - represents value which can be associated with specific match or
        action.

Table - represents a hardware block which can be described with match/
        action behavior. The match/action can be done on the packets
        data or on the internal metadata that it gathered along the
        packets traversal throw the pipeline which is vendor specific
        and should be exported in order to provide understanding of
        ASICs behavior.

Entry - represents single record in a specific table. The entry is
        identified by specific combination of values for match/action.

Prior to accessing the tables/entries the drivers provide the header/
field data base which is used by driver to user-space. The data base
is split between the shared headers and unique headers.

Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7 years agonet/mlx5e: Add offloading of E-Switch TC pedit (header re-write) actions
Or Gerlitz [Wed, 25 Jan 2017 18:24:20 +0000 (20:24 +0200)]
net/mlx5e: Add offloading of E-Switch TC pedit (header re-write) actions

This includes calling the parsing code that translates from pedit
speak to the HW API, allocation (deallocation) of a modify header
context and setting the modify header id associated with this
context to the FTE of that flow.

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
7 years agonet/mlx5e: Add offloading of NIC TC pedit (header re-write) actions
Or Gerlitz [Wed, 25 Jan 2017 17:31:33 +0000 (19:31 +0200)]
net/mlx5e: Add offloading of NIC TC pedit (header re-write) actions

This includes calling the parsing code that translates from pedit
speak to the HW API, allocation (deallocation) of a modify header
context and setting the modify header id associated with this
context to the FTE of that flow.

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
7 years agonet/mlx5e: Add parsing of TC pedit actions to HW format
Or Gerlitz [Sun, 22 Jan 2017 18:46:42 +0000 (20:46 +0200)]
net/mlx5e: Add parsing of TC pedit actions to HW format

Parse/translate a set of TC pedit actions to be formed in the HW API format.

User-space provides set of keys where each one of them is made of: command (add or
set), header-type, byte offset within that header along with a 32 bit mask and value.

The mask dictates what bits in the 32 bit word that starts on the offset we should
be dealing with, but under negative polarity (unset bits are to be modified).

We do a 1st pass over the set of keys while using the header-type and offset to
fill the masks and the values into a data-structure containting all the
supported network headers.

We then do a 2nd pass over the set of fields to re-write supported by the HW,
where for each such candidate field, we use the masks filled on the 1st pass to
realize if we should offloading re-write it.

In case offloading is required, we fill a HW descriptor with the following:

(1) the header field to modify
(2) the bit offset within the field from where to modify (set command only)
(3) the value to set/add
(4) the length in bits 1...32 to modify (set command only)

Note that it's possible for a given pedit mask to dictate modifying the
same header field multiple times or to modify multiple header fields.
Currently such combinations are not supported for offloading, hence, for set
commands, the offset within the field is always zero, and the length to modify
is the field size.

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
7 years agonet/sched: Add accessor functions to pedit keys for offloading drivers
Or Gerlitz [Sun, 22 Jan 2017 18:42:39 +0000 (20:42 +0200)]
net/sched: Add accessor functions to pedit keys for offloading drivers

HW drivers will use the header-type and command fields from the extended
keys, and some fields (e.g mask, val, offset) from the legacy keys.

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
7 years agonet/mlx5: Introduce alloc/dealloc modify header context commands
Or Gerlitz [Thu, 19 Jan 2017 17:49:53 +0000 (19:49 +0200)]
net/mlx5: Introduce alloc/dealloc modify header context commands

Implement the low-level commands to support packet header re-write.

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
7 years agonet/mlx5: Introduce modify header structures, commands and steering action definitions
Or Gerlitz [Thu, 19 Jan 2017 17:31:25 +0000 (19:31 +0200)]
net/mlx5: Introduce modify header structures, commands and steering action definitions

Add the definitions related to creation/deletion of a modify header
context and the modify header steering action which are used for HW
packet header modify (re-write) as part of steering. Add as well the
modify header id into two intermediate structs and set it to the FTE.

Note that as the push/pop vlan steering actions are emulated by the
ewitch management code, we're not breaking any compatibility while
changing their values to make room for the modify header action which
is not emulated and whose value is part of the FW API. The new bit
values for the emulated actions are at the end of the possible range.

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
7 years agonet/mlx5: Reorder few command cases to reflect their natural order
Or Gerlitz [Thu, 19 Jan 2017 17:37:06 +0000 (19:37 +0200)]
net/mlx5: Reorder few command cases to reflect their natural order

Move the commands related to scheduling elements and vport qos to
a suitable location (according to the MLX5_CMD_OP enum values) in
the command string and internal error helpers.

This patch doesn't change any functionality.

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
7 years agonet/mlx5: Add helper to initialize a flow steering actions struct instance
Or Gerlitz [Wed, 1 Feb 2017 17:01:18 +0000 (19:01 +0200)]
net/mlx5: Add helper to initialize a flow steering actions struct instance

There are bunch of places in the code where the intermediate struct
that keeps the elements related to flow actions is initialized with
the same default values. Put that into a small DECLARE type helper.

This patch doesn't change any functionality.

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
7 years agonet/mlx5e: Properly deal with resource cleanup when adding TC flow fails
Or Gerlitz [Tue, 14 Mar 2017 14:49:04 +0000 (16:49 +0200)]
net/mlx5e: Properly deal with resource cleanup when adding TC flow fails

The code for adding tc fdb flows leaves things half set when it fails
in the middle. Currently we are not leaking things (e.g eswitch
vlan reference, encap reference and HW resources) since the main
code to add flower rules does a cleanup by calling mlx5e_tc_del_flow().

This cleanup further works just b/c we're checking there if the HW rule
for the flow we are attempting to delete is valid before touching it, and
since under the current possible combinations of supported actions it's okay
to go and blidnly deref or delete all the action related resources (encap, vlan).

Instead, do things properly, namely make sure that if add flow fails we
clean all what was allocated or referenced. Now, the flow delete code can
blindly deref/deallocate both the rule and the actions related resources and
when more action combinations are introduced (such as the upcoming header
re-write) we are fine with clear and robust code.

While here, align all of nic/fdb parse actions/add flow functions to get
mlx5e_tc_flow struct param and pick the attributes or whatever else needed
from there.

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
7 years agonet/mlx5e: Add intermediate struct for TC flow parsing attributes
Or Gerlitz [Mon, 13 Mar 2017 06:33:03 +0000 (08:33 +0200)]
net/mlx5e: Add intermediate struct for TC flow parsing attributes

Add intermediate structure to store attributes parsed from TC filter
matching/actions parts which are soon to be configured into the HW.

Currently put there the flow matching spec after being parsed. More
content to be added in down-stream patch.

This patch doesn't change any functionality.

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
7 years agonet/mlx5e: Add NIC attributes for offloaded TC flows
Or Gerlitz [Tue, 24 Jan 2017 19:04:50 +0000 (21:04 +0200)]
net/mlx5e: Add NIC attributes for offloaded TC flows

Add structure that contains the attributes related to offloaded
NIC flows. Currently it has the actions and flow tag.

While here, do xmas tree cleanup of the TC configure function.

This patch doesn't change any functionality.

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
7 years agonet/mlx5e: Add prefix for e-switch offloaded TC flow attributes
Or Gerlitz [Tue, 24 Jan 2017 18:54:09 +0000 (20:54 +0200)]
net/mlx5e: Add prefix for e-switch offloaded TC flow attributes

Add esw_ prefix to the flow attributes attached to offloaded e-switch
TC flows. This is a pre-step to add attributes to offloaded NIC TC flows.

Also, save one pointer space by using gcc's zero size array, this would
be beneficial for environments where 100Ks (or Ms) of flows are offloaded.

This patch doesn't change any functionality.

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>