git.openwrt.org Git - openwrt/staging/blogic.git/log

vxlan: test dev->flags & IFF_UP before calling gro_cells_receive()

Same reasons than the ones explained in commit 4179cb5a4c92
("vxlan: test dev->flags & IFF_UP before calling netif_rx()")

netif_rx() or gro_cells_receive() must be called under a strict contract.

At device dismantle phase, core networking clears IFF_UP
and flush_all_backlogs() is called after rcu grace period
to make sure no incoming packet might be in a cpu backlog
and still referencing the device.

A similar protocol is used for gro_cells infrastructure, as
gro_cells_destroy() will be called only after a full rcu
grace period is observed after IFF_UP has been cleared.

Most drivers call netif_rx() from their interrupt handler,
and since the interrupts are disabled at device dismantle,
netif_rx() does not have to check dev->flags & IFF_UP

Virtual drivers do not have this guarantee, and must
therefore make the check themselves.

Otherwise we risk use-after-free and/or crashes.

Fixes: d342894c5d2f ("vxlan: virtual extensible lan")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/x25: fix use-after-free in x25_device_event()

In case of failure x25_connect() does a x25_neigh_put(x25->neighbour)
but forgets to clear x25->neighbour pointer, thus triggering use-after-free.

Since the socket is visible in x25_list, we need to hold x25_list_lock
to protect the operation.

syzbot report :

BUG: KASAN: use-after-free in x25_kill_by_device net/x25/af_x25.c:217 [inline]
BUG: KASAN: use-after-free in x25_device_event+0x296/0x2b0 net/x25/af_x25.c:252
Read of size 8 at addr ffff8880a030edd0 by task syz-executor003/7854

CPU: 0 PID: 7854 Comm: syz-executor003 Not tainted 5.0.0+ #97
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
print_address_description.cold+0x7c/0x20d mm/kasan/report.c:187
kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317
__asan_report_load8_noabort+0x14/0x20 mm/kasan/generic_report.c:135
x25_kill_by_device net/x25/af_x25.c:217 [inline]
x25_device_event+0x296/0x2b0 net/x25/af_x25.c:252
notifier_call_chain+0xc7/0x240 kernel/notifier.c:93
__raw_notifier_call_chain kernel/notifier.c:394 [inline]
raw_notifier_call_chain+0x2e/0x40 kernel/notifier.c:401
call_netdevice_notifiers_info+0x3f/0x90 net/core/dev.c:1739
call_netdevice_notifiers_extack net/core/dev.c:1751 [inline]
call_netdevice_notifiers net/core/dev.c:1765 [inline]
__dev_notify_flags+0x1e9/0x2c0 net/core/dev.c:7607
dev_change_flags+0x10d/0x170 net/core/dev.c:7643
dev_ifsioc+0x2b0/0x940 net/core/dev_ioctl.c:237
dev_ioctl+0x1b8/0xc70 net/core/dev_ioctl.c:488
sock_do_ioctl+0x1bd/0x300 net/socket.c:995
sock_ioctl+0x32b/0x610 net/socket.c:1096
vfs_ioctl fs/ioctl.c:46 [inline]
file_ioctl fs/ioctl.c:509 [inline]
do_vfs_ioctl+0xd6e/0x1390 fs/ioctl.c:696
ksys_ioctl+0xab/0xd0 fs/ioctl.c:713
__do_sys_ioctl fs/ioctl.c:720 [inline]
__se_sys_ioctl fs/ioctl.c:718 [inline]
__x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:718
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x4467c9
Code: e8 0c e8 ff ff 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 5b 07 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007fdbea222d98 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00000000006dbc58 RCX: 00000000004467c9
RDX: 0000000020000340 RSI: 0000000000008914 RDI: 0000000000000003
RBP: 00000000006dbc50 R08: 00007fdbea223700 R09: 0000000000000000
R10: 00007fdbea223700 R11: 0000000000000246 R12: 00000000006dbc5c
R13: 6000030030626669 R14: 0000000000000000 R15: 0000000030626669

Allocated by task 7843:
save_stack+0x45/0xd0 mm/kasan/common.c:73
set_track mm/kasan/common.c:85 [inline]
__kasan_kmalloc mm/kasan/common.c:495 [inline]
__kasan_kmalloc.constprop.0+0xcf/0xe0 mm/kasan/common.c:468
kasan_kmalloc+0x9/0x10 mm/kasan/common.c:509
kmem_cache_alloc_trace+0x151/0x760 mm/slab.c:3615
kmalloc include/linux/slab.h:545 [inline]
x25_link_device_up+0x46/0x3f0 net/x25/x25_link.c:249
x25_device_event+0x116/0x2b0 net/x25/af_x25.c:242
notifier_call_chain+0xc7/0x240 kernel/notifier.c:93
__raw_notifier_call_chain kernel/notifier.c:394 [inline]
raw_notifier_call_chain+0x2e/0x40 kernel/notifier.c:401
call_netdevice_notifiers_info+0x3f/0x90 net/core/dev.c:1739
call_netdevice_notifiers_extack net/core/dev.c:1751 [inline]
call_netdevice_notifiers net/core/dev.c:1765 [inline]
__dev_notify_flags+0x121/0x2c0 net/core/dev.c:7605
dev_change_flags+0x10d/0x170 net/core/dev.c:7643
dev_ifsioc+0x2b0/0x940 net/core/dev_ioctl.c:237
dev_ioctl+0x1b8/0xc70 net/core/dev_ioctl.c:488
sock_do_ioctl+0x1bd/0x300 net/socket.c:995
sock_ioctl+0x32b/0x610 net/socket.c:1096
vfs_ioctl fs/ioctl.c:46 [inline]
file_ioctl fs/ioctl.c:509 [inline]
do_vfs_ioctl+0xd6e/0x1390 fs/ioctl.c:696
ksys_ioctl+0xab/0xd0 fs/ioctl.c:713
__do_sys_ioctl fs/ioctl.c:720 [inline]
__se_sys_ioctl fs/ioctl.c:718 [inline]
__x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:718
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe

Freed by task 7865:
save_stack+0x45/0xd0 mm/kasan/common.c:73
set_track mm/kasan/common.c:85 [inline]
__kasan_slab_free+0x102/0x150 mm/kasan/common.c:457
kasan_slab_free+0xe/0x10 mm/kasan/common.c:465
__cache_free mm/slab.c:3494 [inline]
kfree+0xcf/0x230 mm/slab.c:3811
x25_neigh_put include/net/x25.h:253 [inline]
x25_connect+0x8d8/0xde0 net/x25/af_x25.c:824
__sys_connect+0x266/0x330 net/socket.c:1685
__do_sys_connect net/socket.c:1696 [inline]
__se_sys_connect net/socket.c:1693 [inline]
__x64_sys_connect+0x73/0xb0 net/socket.c:1693
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe

The buggy address belongs to the object at ffff8880a030edc0
which belongs to the cache kmalloc-256 of size 256
The buggy address is located 16 bytes inside of
256-byte region [ffff8880a030edc0, ffff8880a030eec0)
The buggy address belongs to the page:
page:ffffea000280c380 count:1 mapcount:0 mapping:ffff88812c3f07c0 index:0x0
flags: 0x1fffc0000000200(slab)
raw: 01fffc0000000200 ffffea0002806788 ffffea00027f0188 ffff88812c3f07c0
raw: 0000000000000000 ffff8880a030e000 000000010000000c 0000000000000000
page dumped because: kasan: bad access detected

Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot+04babcefcd396fabec37@syzkaller.appspotmail.com
Cc: andrew hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

isdn: mISDNinfineon: fix potential NULL pointer dereference

In case ioremap fails, the fix returns -ENOMEM to avoid NULL
pointer dereference.

Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix to stop multiple HNS reset due to the AER changes

The commit bfcb79fca19d
("PCI/ERR: Run error recovery callbacks for all affected devices")
affected the non-fatal error recovery logic for the HNS and RDMA devices.
This is because each HNS PF under PCIe bus receive callbacks
from the AER driver when an error is reported for one of the PF.
This causes unwanted PF resets because
the HNS decides which PF to reset based on the reset type set.
The HNS error handling code sets the reset type based on the hw error
type detected.

This patch provides fix for the above issue for the recovery of
the hw errors in the HNS and RDMA devices.

This patch needs backporting to the kernel v5.0+

Fixes: 332fbf576579 ("net: hns3: add handling of hw ras errors using new set of commands")
Reported-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip: fix ip_mc_may_pull() return value

ip_mc_may_pull() must return 0 if there is a problem, not an errno.

syzbot reported :

BUG: KASAN: use-after-free in br_ip4_multicast_igmp3_report net/bridge/br_multicast.c:947 [inline]
BUG: KASAN: use-after-free in br_multicast_ipv4_rcv net/bridge/br_multicast.c:1631 [inline]
BUG: KASAN: use-after-free in br_multicast_rcv+0x3cd8/0x4440 net/bridge/br_multicast.c:1741
Read of size 4 at addr ffff88820a4084ee by task syz-executor.2/11183

CPU: 1 PID: 11183 Comm: syz-executor.2 Not tainted 5.0.0+ #14
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
print_address_description.cold+0x7c/0x20d mm/kasan/report.c:187
kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317
__asan_report_load4_noabort+0x14/0x20 mm/kasan/generic_report.c:131
br_ip4_multicast_igmp3_report net/bridge/br_multicast.c:947 [inline]
br_multicast_ipv4_rcv net/bridge/br_multicast.c:1631 [inline]
br_multicast_rcv+0x3cd8/0x4440 net/bridge/br_multicast.c:1741
br_handle_frame_finish+0xa3a/0x14c0 net/bridge/br_input.c:108
br_nf_hook_thresh+0x2ec/0x380 net/bridge/br_netfilter_hooks.c:1005
br_nf_pre_routing_finish+0x8e2/0x1750 net/bridge/br_netfilter_hooks.c:410
NF_HOOK include/linux/netfilter.h:289 [inline]
NF_HOOK include/linux/netfilter.h:283 [inline]
br_nf_pre_routing+0x7e7/0x13a0 net/bridge/br_netfilter_hooks.c:506
nf_hook_entry_hookfn include/linux/netfilter.h:119 [inline]
nf_hook_slow+0xbf/0x1f0 net/netfilter/core.c:511
nf_hook include/linux/netfilter.h:244 [inline]
NF_HOOK include/linux/netfilter.h:287 [inline]
br_handle_frame+0x95b/0x1450 net/bridge/br_input.c:305
__netif_receive_skb_core+0xa96/0x3040 net/core/dev.c:4902
__netif_receive_skb_one_core+0xa8/0x1a0 net/core/dev.c:4971
__netif_receive_skb+0x2c/0x1c0 net/core/dev.c:5083
netif_receive_skb_internal+0x117/0x660 net/core/dev.c:5186
netif_receive_skb+0x6e/0x5a0 net/core/dev.c:5261

Fixes: ba5ea614622d ("bridge: simplify ip_mc_check_igmp() and ipv6_mc_check_mld() calls")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: keep refcount warning in reqsk_free()

As Eric Dumazet said, "We do not have a way to tell if the req was ever
inserted in a hash table, so better play safe.".
Let's remove this comment, so that nobody will be tempted to drop the
WARN_ON_ONCE() line.

Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: stmmac: Avoid one more sometimes uninitialized Clang warning

When building with -Wsometimes-uninitialized, Clang warns:

drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.c:111:2: error: variable
'ns' is used uninitialized whenever 'if' condition is false
[-Werror,-Wsometimes-uninitialized]
drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.c:111:2: error: variable
'ns' is used uninitialized whenever '&&' condition is false
[-Werror,-Wsometimes-uninitialized]

Clang is concerned with the use of stmmac_do_void_callback (which
stmmac_get_systime wraps), as it may fail to initialize these values if
the if condition was ever false (meaning the callback doesn't exist).
It's not wrong because the callback is what initializes ns. While it's
unlikely that the callback is going to disappear at some point and make
that condition false, we can easily avoid this warning by zero
initializing the variable.

Link: https://github.com/ClangBuiltLinux/linux/issues/384
Fixes: df103170854e ("net: stmmac: Avoid sometimes uninitialized Clang warnings")
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: Set correct interface mode for CPU/DSA ports

By default, the switch driver is expected to configure CPU and DSA
ports to their maximum speed. For the 6341 and 6390 families, the
ports interface mode has to be configured as well. The 6390X range
support 10G ports using XAUI, while the 6341 and 6390 supports
2500BaseX, as their maximum speed.

Fixes: 787799a9d555 ("net: dsa: mv88e6xxx: Default ports 9/10 6390X CMODE to 1000BaseX")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

rxrpc: Fix client call queueing, waiting for channel

rxrpc_get_client_conn() adds a new call to the front of the waiting_calls
queue if the connection it's going to use already exists. This is bad as
it allows calls to get starved out.

Fix this by adding to the tail instead.

Also change the other enqueue point in the same function to put it on the
front (ie. when we have a new connection). This makes the point that in
the case of a new connection the new call goes at the front (though it
doesn't actually matter since the queue should be unoccupied).

Fixes: 45025bceef17 ("rxrpc: Improve management and caching of client connection objects")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge git://git./pub/scm/linux/kernel/git/bpf/bpf

Daniel Borkmann says:

====================
pull-request: bpf 2019-03-09

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Fix a crash in AF_XDP's xsk_diag_put_ring() which was passing
   wrong queue argument, from Eric.

2) Fix a regression due to wrong test for TCP GSO packets used in
   various BPF helpers like NAT64, from Willem.

3) Fix a sk_msg strparser warning which asserts that strparser must
   be stopped first, from Jakub.

4) Fix rejection of invalid options/bind flags in AF_XDP, from Björn.

5) Fix GSO in bpf_lwt_push_ip_encap() which must properly set inner
   headers and inner protocol, from Peter.

6) Fix a libbpf leak when kernel does not support BTF, from Nikita.

7) Various BPF selftest and libbpf build fixes to make out-of-tree
   compilation work and to properly resolve dependencies via fixdep
   target, from Stanislav.

8) Fix rejection of invalid ldimm64 imm field, from Daniel.

9) Fix bpf stats sysctl compile warning of unused helper function
   proc_dointvec_minmax_bpf_stats() under some configs, from Arnd.

10) Fix couple of warnings about using plain integer as NULL, from Bo.

11) Fix some BPF sample spelling mistakes, from Colin.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: handle inet_csk_reqsk_queue_add() failures

Commit 7716682cc58e ("tcp/dccp: fix another race at listener
dismantle") let inet_csk_reqsk_queue_add() fail, and adjusted
{tcp,dccp}_check_req() accordingly. However, TFO and syncookies
weren't modified, thus leaking allocated resources on error.

Contrary to tcp_check_req(), in both syncookies and TFO cases,
we need to drop the request socket. Also, since the child socket is
created with inet_csk_clone_lock(), we have to unlock it and drop an
extra reference (->sk_refcount is initially set to 2 and
inet_csk_reqsk_queue_add() drops only one ref).

For TFO, we also need to revert the work done by tcp_try_fastopen()
(with reqsk_fastopen_remove()).

Fixes: 7716682cc58e ("tcp/dccp: fix another race at listener dismantle")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: sun: Zero initialize class in default case in niu_add_ethtool_tcam_entry

When building with -Wsometimes-uninitialized, Clang warns:

drivers/net/ethernet/sun/niu.c:7466:5: warning: variable 'class' is used
uninitialized whenever switch default is taken
[-Wsometimes-uninitialized]

The default case can never happen because i can only be 0 to 3
(NIU_L3_PROG_CLS is defined as 4). To make this clear to Clang,
just zero initialize class in the default case (use the macro
CLASS_CODE_UNRECOG to make it clear this shouldn't happen).

Link: https://github.com/ClangBuiltLinux/linux/issues/403
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8139too : Add support for U.S. Robotics USR997901A 10/100 Cardbus NIC

Add PCI vendor and device identifier for U.S. Robotics USR997901A
10/100 Cardbus NIC. Tested on real hardware.

Signed-off-by: Matthew Whitehead <tedheadster@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fou, fou6: avoid uninit-value in gue_err() and gue6_err()

My prior commit missed the fact that these functions
were using udp_hdr() (aka skb_transport_header())
to get access to GUE header.

Since pskb_transport_may_pull() does not exist yet, we have to add
transport_offset to our pskb_may_pull() calls.

BUG: KMSAN: uninit-value in gue_err+0x514/0xfa0 net/ipv4/fou.c:1032
CPU: 1 PID: 10648 Comm: syz-executor.1 Not tainted 5.0.0+ #11
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x173/0x1d0 lib/dump_stack.c:113
kmsan_report+0x12e/0x2a0 mm/kmsan/kmsan.c:600
__msan_warning+0x82/0xf0 mm/kmsan/kmsan_instr.c:313
gue_err+0x514/0xfa0 net/ipv4/fou.c:1032
__udp4_lib_err_encap_no_sk net/ipv4/udp.c:571 [inline]
__udp4_lib_err_encap net/ipv4/udp.c:626 [inline]
__udp4_lib_err+0x12e6/0x1d40 net/ipv4/udp.c:665
udp_err+0x74/0x90 net/ipv4/udp.c:737
icmp_socket_deliver net/ipv4/icmp.c:767 [inline]
icmp_unreach+0xb65/0x1070 net/ipv4/icmp.c:884
icmp_rcv+0x11a1/0x1950 net/ipv4/icmp.c:1066
ip_protocol_deliver_rcu+0x584/0xbb0 net/ipv4/ip_input.c:208
ip_local_deliver_finish net/ipv4/ip_input.c:234 [inline]
NF_HOOK include/linux/netfilter.h:289 [inline]
ip_local_deliver+0x624/0x7b0 net/ipv4/ip_input.c:255
dst_input include/net/dst.h:450 [inline]
ip_rcv_finish net/ipv4/ip_input.c:414 [inline]
NF_HOOK include/linux/netfilter.h:289 [inline]
ip_rcv+0x6bd/0x740 net/ipv4/ip_input.c:524
__netif_receive_skb_one_core net/core/dev.c:4973 [inline]
__netif_receive_skb net/core/dev.c:5083 [inline]
process_backlog+0x756/0x10e0 net/core/dev.c:5923
napi_poll net/core/dev.c:6346 [inline]
net_rx_action+0x78b/0x1a60 net/core/dev.c:6412
__do_softirq+0x53f/0x93a kernel/softirq.c:293
invoke_softirq kernel/softirq.c:375 [inline]
irq_exit+0x214/0x250 kernel/softirq.c:416
exiting_irq+0xe/0x10 arch/x86/include/asm/apic.h:536
smp_apic_timer_interrupt+0x48/0x70 arch/x86/kernel/apic/apic.c:1064
apic_timer_interrupt+0x2e/0x40 arch/x86/entry/entry_64.S:814
</IRQ>
RIP: 0010:finish_lock_switch+0x2b/0x40 kernel/sched/core.c:2597
Code: 48 89 e5 53 48 89 fb e8 63 e7 95 00 8b b8 88 0c 00 00 48 8b 00 48 85 c0 75 12 48 89 df e8 dd db 95 00 c6 00 00 c6 03 00 fb 5b <5d> c3 e8 4e e6 95 00 eb e7 66 90 66 2e 0f 1f 84 00 00 00 00 00 55
RSP: 0018:ffff888081a0fc80 EFLAGS: 00000296 ORIG_RAX: ffffffffffffff13
RAX: ffff88821fd6bd80 RBX: ffff888027898000 RCX: ccccccccccccd000
RDX: ffff88821fca8d80 RSI: ffff888000000000 RDI: 00000000000004a0
RBP: ffff888081a0fc80 R08: 0000000000000002 R09: ffff888081a0fb08
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000001
R13: ffff88811130e388 R14: ffff88811130da00 R15: ffff88812fdb7d80
finish_task_switch+0xfc/0x2d0 kernel/sched/core.c:2698
context_switch kernel/sched/core.c:2851 [inline]
__schedule+0x6cc/0x800 kernel/sched/core.c:3491
schedule+0x15b/0x240 kernel/sched/core.c:3535
freezable_schedule include/linux/freezer.h:172 [inline]
do_nanosleep+0x2ba/0x980 kernel/time/hrtimer.c:1679
hrtimer_nanosleep kernel/time/hrtimer.c:1733 [inline]
__do_sys_nanosleep kernel/time/hrtimer.c:1767 [inline]
__se_sys_nanosleep+0x746/0x960 kernel/time/hrtimer.c:1754
__x64_sys_nanosleep+0x3e/0x60 kernel/time/hrtimer.c:1754
do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291
entry_SYSCALL_64_after_hwframe+0x63/0xe7
RIP: 0033:0x4855a0
Code: 00 00 48 c7 c0 d4 ff ff ff 64 c7 00 16 00 00 00 31 c0 eb be 66 0f 1f 44 00 00 83 3d b1 11 5d 00 00 75 14 b8 23 00 00 00 0f 05 <48> 3d 01 f0 ff ff 0f 83 04 e2 f8 ff c3 48 83 ec 08 e8 3a 55 fd ff
RSP: 002b:0000000000a4fd58 EFLAGS: 00000246 ORIG_RAX: 0000000000000023
RAX: ffffffffffffffda RBX: 0000000000085780 RCX: 00000000004855a0
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000a4fd60
RBP: 00000000000007ec R08: 0000000000000001 R09: 0000000000ceb940
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000008
R13: 0000000000a4fdb0 R14: 0000000000085711 R15: 0000000000a4fdc0

Uninit was created at:
kmsan_save_stack_with_flags mm/kmsan/kmsan.c:205 [inline]
kmsan_internal_poison_shadow+0x92/0x150 mm/kmsan/kmsan.c:159
kmsan_kmalloc+0xa6/0x130 mm/kmsan/kmsan_hooks.c:176
kmsan_slab_alloc+0xe/0x10 mm/kmsan/kmsan_hooks.c:185
slab_post_alloc_hook mm/slab.h:445 [inline]
slab_alloc_node mm/slub.c:2773 [inline]
__kmalloc_node_track_caller+0xe9e/0xff0 mm/slub.c:4398
__kmalloc_reserve net/core/skbuff.c:140 [inline]
__alloc_skb+0x309/0xa20 net/core/skbuff.c:208
alloc_skb include/linux/skbuff.h:1012 [inline]
alloc_skb_with_frags+0x186/0xa60 net/core/skbuff.c:5287
sock_alloc_send_pskb+0xafd/0x10a0 net/core/sock.c:2091
sock_alloc_send_skb+0xca/0xe0 net/core/sock.c:2108
__ip_append_data+0x34cd/0x5000 net/ipv4/ip_output.c:998
ip_append_data+0x324/0x480 net/ipv4/ip_output.c:1220
icmp_push_reply+0x23d/0x7e0 net/ipv4/icmp.c:375
__icmp_send+0x2ea3/0x30f0 net/ipv4/icmp.c:737
icmp_send include/net/icmp.h:47 [inline]
ipv4_link_failure+0x6d/0x230 net/ipv4/route.c:1190
dst_link_failure include/net/dst.h:427 [inline]
arp_error_report+0x106/0x1a0 net/ipv4/arp.c:297
neigh_invalidate+0x359/0x8e0 net/core/neighbour.c:992
neigh_timer_handler+0xdf2/0x1280 net/core/neighbour.c:1078
call_timer_fn+0x285/0x600 kernel/time/timer.c:1325
expire_timers kernel/time/timer.c:1362 [inline]
__run_timers+0xdb4/0x11d0 kernel/time/timer.c:1681
run_timer_softirq+0x2e/0x50 kernel/time/timer.c:1694
__do_softirq+0x53f/0x93a kernel/softirq.c:293

Fixes: 26fc181e6cac ("fou, fou6: do not assume linear skbs")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Stefano Brivio <sbrivio@redhat.com>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sched: fix potential use-after-free in __tcf_chain_put()

When used with unlocked classifier that have filters attached to actions
with goto chain, __tcf_chain_put() for last non action reference can race
with calls to same function from action cleanup code that releases last
action reference. In this case action cleanup handler could free the chain
if it executes after all references to chain were released, but before all
concurrent users finished using it. Modify __tcf_chain_put() to only access
tcf_chain fields when holding block->lock. Remove local variables that were
used to cache some tcf_chain fields and are no longer needed because their
values can now be obtained directly from chain under block->lock
protection.

Fixes: 726d061286ce ("net: sched: prevent insertion of new classifiers during chain flush")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vhost: silence an unused-variable warning

On some architectures, the MMU can be disabled, leading to access_ok()
becoming an empty macro that does not evaluate its size argument,
which in turn produces an unused-variable warning:

drivers/vhost/vhost.c:1191:9: error: unused variable 's' [-Werror,-Wunused-variable]
size_t s = vhost_has_feature(vq, VIRTIO_RING_F_EVENT_IDX) ? 2 : 0;

Mark the variable as __maybe_unused to shut up that warning.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vsock/virtio: fix kernel panic from virtio_transport_reset_no_sock

Previous to commit 22b5c0b63f32 ("vsock/virtio: fix kernel panic
after device hot-unplug"), vsock_core_init() was called from
virtio_vsock_probe(). Now, virtio_transport_reset_no_sock() can be called
before vsock_core_init() has the chance to run.

[Wed Feb 27 14:17:09 2019] BUG: unable to handle kernel NULL pointer dereference at 0000000000000110
[Wed Feb 27 14:17:09 2019] #PF error: [normal kernel read fault]
[Wed Feb 27 14:17:09 2019] PGD 0 P4D 0
[Wed Feb 27 14:17:09 2019] Oops: 0000 [#1] SMP PTI
[Wed Feb 27 14:17:09 2019] CPU: 3 PID: 59 Comm: kworker/3:1 Not tainted 5.0.0-rc7-390-generic-hvi #390
[Wed Feb 27 14:17:09 2019] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014
[Wed Feb 27 14:17:09 2019] Workqueue: virtio_vsock virtio_transport_rx_work [vmw_vsock_virtio_transport]
[Wed Feb 27 14:17:09 2019] RIP: 0010:virtio_transport_reset_no_sock+0x8c/0xc0 [vmw_vsock_virtio_transport_common]
[Wed Feb 27 14:17:09 2019] Code: 35 8b 4f 14 48 8b 57 08 31 f6 44 8b 4f 10 44 8b 07 48 8d 7d c8 e8 84 f8 ff ff 48 85 c0 48 89 c3 74 2a e8 f7 31 03 00 48 89 df <48> 8b 80 10 01 00 00 e8 68 fb 69 ed 48 8b 75 f0 65 48 33 34 25 28
[Wed Feb 27 14:17:09 2019] RSP: 0018:ffffb42701ab7d40 EFLAGS: 00010282
[Wed Feb 27 14:17:09 2019] RAX: 0000000000000000 RBX: ffff9d79637ee080 RCX: 0000000000000003
[Wed Feb 27 14:17:09 2019] RDX: 0000000000000001 RSI: 0000000000000002 RDI: ffff9d79637ee080
[Wed Feb 27 14:17:09 2019] RBP: ffffb42701ab7d78 R08: ffff9d796fae70e0 R09: ffff9d796f403500
[Wed Feb 27 14:17:09 2019] R10: ffffb42701ab7d90 R11: 0000000000000000 R12: ffff9d7969d09240
[Wed Feb 27 14:17:09 2019] R13: ffff9d79624e6840 R14: ffff9d7969d09318 R15: ffff9d796d48ff80
[Wed Feb 27 14:17:09 2019] FS:  0000000000000000(0000) GS:ffff9d796fac0000(0000) knlGS:0000000000000000
[Wed Feb 27 14:17:09 2019] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[Wed Feb 27 14:17:09 2019] CR2: 0000000000000110 CR3: 0000000427f22000 CR4: 00000000000006e0
[Wed Feb 27 14:17:09 2019] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[Wed Feb 27 14:17:09 2019] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[Wed Feb 27 14:17:09 2019] Call Trace:
[Wed Feb 27 14:17:09 2019]  virtio_transport_recv_pkt+0x63/0x820 [vmw_vsock_virtio_transport_common]
[Wed Feb 27 14:17:09 2019]  ? kfree+0x17e/0x190
[Wed Feb 27 14:17:09 2019]  ? detach_buf_split+0x145/0x160
[Wed Feb 27 14:17:09 2019]  ? __switch_to_asm+0x40/0x70
[Wed Feb 27 14:17:09 2019]  virtio_transport_rx_work+0xa0/0x106 [vmw_vsock_virtio_transport]
[Wed Feb 27 14:17:09 2019] NET: Registered protocol family 40
[Wed Feb 27 14:17:09 2019]  process_one_work+0x167/0x410
[Wed Feb 27 14:17:09 2019]  worker_thread+0x4d/0x460
[Wed Feb 27 14:17:09 2019]  kthread+0x105/0x140
[Wed Feb 27 14:17:09 2019]  ? rescuer_thread+0x360/0x360
[Wed Feb 27 14:17:09 2019]  ? kthread_destroy_worker+0x50/0x50
[Wed Feb 27 14:17:09 2019]  ret_from_fork+0x35/0x40
[Wed Feb 27 14:17:09 2019] Modules linked in: vmw_vsock_virtio_transport vmw_vsock_virtio_transport_common input_leds vsock serio_raw i2c_piix4 mac_hid qemu_fw_cfg autofs4 cirrus ttm drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops virtio_net psmouse drm net_failover pata_acpi virtio_blk failover floppy

Fixes: 22b5c0b63f32 ("vsock/virtio: fix kernel panic after device hot-unplug")
Reported-by: Alexandru Herghelegiu <aherghelegiu@bitdefender.com>
Signed-off-by: Adalbert Lazăr <alazar@bitdefender.com>
Co-developed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

connector: fix unsafe usage of ->real_parent

proc_exit_connector() uses ->real_parent lockless. This is not
safe that its parent can go away at any moment, so use RCU to
protect it, and ensure that this task is not released.

[  747.624551] ==================================================================
[  747.632946] BUG: KASAN: use-after-free in proc_exit_connector+0x1f7/0x310
[  747.640686] Read of size 4 at addr ffff88a0276988e0 by task sshd/2882
[  747.648032]
[  747.649804] CPU: 11 PID: 2882 Comm: sshd Tainted: G            E     4.19.26-rc2 #11
[  747.658629] Hardware name: IBM x3550M4 -[7914OFV]-/00AM544, BIOS -[D7E142BUS-1.71]- 07/31/2014
[  747.668419] Call Trace:
[  747.671269]  dump_stack+0xf0/0x19b
[  747.675186]  ? show_regs_print_info+0x5/0x5
[  747.679988]  ? kmsg_dump_rewind_nolock+0x59/0x59
[  747.685302]  print_address_description+0x6a/0x270
[  747.691162]  kasan_report+0x258/0x380
[  747.695835]  ? proc_exit_connector+0x1f7/0x310
[  747.701402]  proc_exit_connector+0x1f7/0x310
[  747.706767]  ? proc_coredump_connector+0x2d0/0x2d0
[  747.712715]  ? _raw_write_unlock_irq+0x29/0x50
[  747.718270]  ? _raw_write_unlock_irq+0x29/0x50
[  747.723820]  ? ___preempt_schedule+0x16/0x18
[  747.729193]  ? ___preempt_schedule+0x16/0x18
[  747.734574]  do_exit+0xa11/0x14f0
[  747.738880]  ? mm_update_next_owner+0x590/0x590
[  747.744525]  ? debug_show_all_locks+0x3c0/0x3c0
[  747.761448]  ? ktime_get_coarse_real_ts64+0xeb/0x1c0
[  747.767589]  ? lockdep_hardirqs_on+0x1a6/0x290
[  747.773154]  ? check_chain_key+0x139/0x1f0
[  747.778345]  ? check_flags.part.35+0x240/0x240
[  747.783908]  ? __lock_acquire+0x2300/0x2300
[  747.789171]  ? _raw_spin_unlock_irqrestore+0x59/0x70
[  747.795316]  ? _raw_spin_unlock_irqrestore+0x59/0x70
[  747.801457]  ? do_raw_spin_unlock+0x10f/0x1e0
[  747.806914]  ? do_raw_spin_trylock+0x120/0x120
[  747.812481]  ? preempt_count_sub+0x14/0xc0
[  747.817645]  ? _raw_spin_unlock+0x2e/0x50
[  747.822708]  ? __handle_mm_fault+0x12db/0x1fa0
[  747.828367]  ? __pmd_alloc+0x2d0/0x2d0
[  747.833143]  ? check_noncircular+0x50/0x50
[  747.838309]  ? match_held_lock+0x7f/0x340
[  747.843380]  ? check_noncircular+0x50/0x50
[  747.848561]  ? handle_mm_fault+0x21a/0x5f0
[  747.853730]  ? check_flags.part.35+0x240/0x240
[  747.859290]  ? check_chain_key+0x139/0x1f0
[  747.864474]  ? __do_page_fault+0x40f/0x760
[  747.869655]  ? __audit_syscall_entry+0x4b/0x1f0
[  747.875319]  ? syscall_trace_enter+0x1d5/0x7b0
[  747.880877]  ? trace_raw_output_preemptirq_template+0x90/0x90
[  747.887895]  ? trace_raw_output_sys_exit+0x80/0x80
[  747.893860]  ? up_read+0x3b/0x90
[  747.898142]  ? stop_critical_timings+0x260/0x260
[  747.903909]  do_group_exit+0xe0/0x1c0
[  747.908591]  ? __x64_sys_exit+0x30/0x30
[  747.913460]  ? trace_raw_output_preemptirq_template+0x90/0x90
[  747.920485]  ? tracer_hardirqs_on+0x270/0x270
[  747.925956]  __x64_sys_exit_group+0x28/0x30
[  747.931214]  do_syscall_64+0x117/0x400
[  747.935988]  ? syscall_return_slowpath+0x2f0/0x2f0
[  747.941931]  ? trace_hardirqs_off_thunk+0x1a/0x1c
[  747.947788]  ? trace_hardirqs_on_caller+0x1d0/0x1d0
[  747.953838]  ? lockdep_sys_exit+0x16/0x8e
[  747.958915]  ? trace_hardirqs_off_thunk+0x1a/0x1c
[  747.964784]  entry_SYSCALL_64_after_hwframe+0x49/0xbe
[  747.971021] RIP: 0033:0x7f572f154c68
[  747.975606] Code: Bad RIP value.
[  747.979791] RSP: 002b:00007ffed2dfaa58 EFLAGS: 00000246 ORIG_RAX: 00000000000000e7
[  747.989324] RAX: ffffffffffffffda RBX: 00007f572f431840 RCX: 00007f572f154c68
[  747.997910] RDX: 0000000000000001 RSI: 000000000000003c RDI: 0000000000000001
[  748.006495] RBP: 0000000000000001 R08: 00000000000000e7 R09: fffffffffffffee0
[  748.015079] R10: 00007f572f4387e8 R11: 0000000000000246 R12: 00007f572f431840
[  748.023664] R13: 000055a7f90f2c50 R14: 000055a7f96e2310 R15: 000055a7f96e2310
[  748.032287]
[  748.034509] Allocated by task 2300:
[  748.038982]  kasan_kmalloc+0xa0/0xd0
[  748.043562]  kmem_cache_alloc_node+0xf5/0x2e0
[  748.049018]  copy_process+0x1781/0x4790
[  748.053884]  _do_fork+0x166/0x9a0
[  748.058163]  do_syscall_64+0x117/0x400
[  748.062943]  entry_SYSCALL_64_after_hwframe+0x49/0xbe
[  748.069180]
[  748.071405] Freed by task 15395:
[  748.075591]  __kasan_slab_free+0x130/0x180
[  748.080752]  kmem_cache_free+0xc2/0x310
[  748.085619]  free_task+0xea/0x130
[  748.089901]  __put_task_struct+0x177/0x230
[  748.095063]  finish_task_switch+0x51b/0x5d0
[  748.100315]  __schedule+0x506/0xfa0
[  748.104791]  schedule+0xca/0x260
[  748.108978]  futex_wait_queue_me+0x27e/0x420
[  748.114333]  futex_wait+0x251/0x550
[  748.118814]  do_futex+0x75b/0xf80
[  748.123097]  __x64_sys_futex+0x231/0x2a0
[  748.128065]  do_syscall_64+0x117/0x400
[  748.132835]  entry_SYSCALL_64_after_hwframe+0x49/0xbe
[  748.139066]
[  748.141289] The buggy address belongs to the object at ffff88a027698000
[  748.141289]  which belongs to the cache task_struct of size 12160
[  748.156589] The buggy address is located 2272 bytes inside of
[  748.156589]  12160-byte region [ffff88a027698000, ffff88a02769af80)
[  748.171114] The buggy address belongs to the page:
[  748.177055] page:ffffea00809da600 count:1 mapcount:0 mapping:ffff888107d01e00 index:0x0 compound_mapcount: 0
[  748.189136] flags: 0x57ffffc0008100(slab|head)
[  748.194688] raw: 0057ffffc0008100 ffffea00809a3200 0000000300000003 ffff888107d01e00
[  748.204424] raw: 0000000000000000 0000000000020002 00000001ffffffff 0000000000000000
[  748.214146] page dumped because: kasan: bad access detected
[  748.220976]
[  748.223197] Memory state around the buggy address:
[  748.229128]  ffff88a027698780: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  748.238271]  ffff88a027698800: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  748.247414] >ffff88a027698880: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  748.256564]                                                        ^
[  748.264267]  ffff88a027698900: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  748.273493]  ffff88a027698980: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[  748.282630] ==================================================================

Fixes: b086ff87251b4a4 ("connector: add parent pid and tgid to coredump and exit events")
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

vxlan: do not need BH again in vxlan_cleanup()

vxlan_cleanup() is a timer callback, it is already
and only running in BH context.

Signed-off-by: Litao Jiao <jiaolitao@raisecom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add dma_rmb() for rx description

HW can not guarantee complete write desc->rx.size, even though
HNS3_RXD_VLD_B has been set. Driver needs to add dma_rmb()
instruction to make sure desc->rx.size is always valid.

Fixes: e55970950556 ("net: hns3: Add handling of GRO Pkts not fully RX'ed in NAPI poll")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: add missing documentation in linux/skbuff.h

This patch adds missing documentation for some inline functions on
linux/skbuff.h. The patch is incomplete and a lot more can be added,
just wondering if it's of interest of the netdev developers.

Also fixed some whitespaces.

Signed-off-by: Pedro Tammela <pctammela@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bpf: fix warning about using plain integer as NULL

Sparse warning below:

sudo make C=2 CF=-D__CHECK_ENDIAN__ M=net/bpf/
CHECK net/bpf//test_run.c
net/bpf//test_run.c:19:77: warning: Using plain integer as NULL pointer
./include/linux/bpf-cgroup.h:295:77: warning: Using plain integer as NULL pointer

Fixes: 8bad74f9840f ("bpf: extend cgroup bpf core to allow multiple cgroup storage types")
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Bo YU <tsu.yubo@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

xsk: fix to reject invalid options in Tx descriptor

Passing a non-existing option in the options member of struct
xdp_desc was, incorrectly, silently ignored. This patch addresses
that behavior, and drops any Tx descriptor with non-existing options.

We have examined existing user space code, and to our best knowledge,
no one is relying on the current incorrect behavior. AF_XDP is still
in its infancy, so from our perspective, the risk of breakage is very
low, and addressing this problem now is important.

Fixes: 35fcde7f8deb ("xsk: support for Tx")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

xsk: fix to reject invalid flags in xsk_bind

Passing a non-existing flag in the sxdp_flags member of struct
sockaddr_xdp was, incorrectly, silently ignored. This patch addresses
that behavior, and rejects any non-existing flags.

We have examined existing user space code, and to our best knowledge,
no one is relying on the current incorrect behavior. AF_XDP is still
in its infancy, so from our perspective, the risk of breakage is very
low, and addressing this problem now is important.

Fixes: 965a99098443 ("xsk: add support for bind for Rx")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

bpf, libbpf: fixing leak when kernel does not support btf

We could end up in situation when we have object file w/ all btf
info, but kernel does not support btf yet. In this situation
currently libbpf just set obj->btf to NULL w/o freeing it first.
This patch is fixing it by making sure to run btf__free first.

Fixes: d29d87f7e612 ("btf: separate btf creation and loading")
Signed-off-by: Nikita V. Shirokov <tehnerd@tehnerd.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Merge branch 'stmmac-add-some-fixes-for-stm32'

Christophe Roullier says:

====================
stmmac: add some fixes for stm32

For common stmmac:
- Add support to set CSR Clock range selection in DT
For stm32mpu:
- Glue codes to support magic packet
- Glue codes to support all PHY config :
PHY_MODE (MII,GMII, RMII, RGMII) and in normal,
PHY wo crystal (25Mhz),
PHY wo crystal (50Mhz), No 125Mhz from PHY config
For stm32mcu:
- Add Ethernet support for stm32h7

Changes in V3:
- Reverse for syscfg management because it is manage by these patches
  https://lkml.org/lkml/2018/12/12/133
  https://lkml.org/lkml/2018/12/12/134
  https://lkml.org/lkml/2018/12/12/131
  https://lkml.org/lkml/2018/12/12/132
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

ARM: dts: stm32: Add Ethernet support on stm32h7 SOC and activate it for eval and disco boards

Synopsys GMAC 4.10 is used. And Phy mode for eval and disco is RMII
with PHY SMSC LAN8742

Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dt-bindings: net: stmmac: remove syscfg clock property

Syscfg clock is no more needed.

Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: stmmac: add management of clk_csr property

In Documentation stmmac.txt there is possibility to
fixed CSR Clock range selection with property clk_csr.
This patch add the management of this property
For example to use it, add in your ethernet node DT:
clk_csr = <3>;

Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dt-bindings: net: stmmac: add phys config properties

Add properties to support all Phy config
PHY_MODE (MII,GMII, RMII, RGMII) and in normal, PHY wo crystal (25Mhz),
PHY wo crystal (50Mhz), No 125Mhz from PHY config.

Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: stmmac: update to support all PHY config for stm32mp157c.

Update glue codes to support all PHY config on stm32mp157c
PHY_MODE (MII,GMII, RMII, RGMII) and in normal, PHY wo crystal (25Mhz),
PHY wo crystal (50Mhz), No 125Mhz from PHY config.

Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: stmmac: manage Ethernet WoL for stm32mp157c.

Add glue codes to support magic packet on stm32mp157c

Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'sctp-process-the-error-returned-from-sctp_sock_migrate'

Xin Long says:

====================
sctp: process the error returned from sctp_sock_migrate()

This patchset is to process the errs returned by sctp_auth_init_hmacs()
and sctp_bind_addr_dup() from sctp_sock_migrate(). And also fix a panic
caused by new ep->auth_hmacs was not set due to net->sctp.auth_enable
changed by sysctl before accepting an assoc.
====================

Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: call sctp_auth_init_hmacs() in sctp_sock_migrate()

New ep's auth_hmacs should be set if old ep's is set, in case that
net->sctp.auth_enable has been changed to 0 by users and new ep's
auth_hmacs couldn't be set in sctp_endpoint_init().

It can even crash kernel by doing:

  1. on server: sysctl -w net.sctp.auth_enable=1,
                sysctl -w net.sctp.addip_enable=1,
                sysctl -w net.sctp.addip_noauth_enable=0,
                listen() on server,
                sysctl -w net.sctp.auth_enable=0.
  2. on client: connect() to server.
  3. on server: accept() the asoc,
                sysctl -w net.sctp.auth_enable=1.
  4. on client: send() asconf packet to server.

The call trace:

  [  245.280251] BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
  [  245.286872] RIP: 0010:sctp_auth_calculate_hmac+0xa3/0x140 [sctp]
  [  245.304572] Call Trace:
  [  245.305091]  <IRQ>
  [  245.311287]  sctp_sf_authenticate+0x110/0x160 [sctp]
  [  245.312311]  sctp_sf_eat_auth+0xf2/0x230 [sctp]
  [  245.313249]  sctp_do_sm+0x9a/0x2d0 [sctp]
  [  245.321483]  sctp_assoc_bh_rcv+0xed/0x1a0 [sctp]
  [  245.322495]  sctp_rcv+0xa66/0xc70 [sctp]

It's because the old ep->auth_hmacs wasn't copied to the new ep while
ep->auth_hmacs is used in sctp_auth_calculate_hmac() when processing
the incoming auth chunks, and it should have been done when migrating
sock.

Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: move up sctp_auth_init_hmacs() in sctp_endpoint_init()

sctp_auth_init_hmacs() is called only when ep->auth_enable is set.
It better to move up sctp_auth_init_hmacs() and remove auth_enable
check in it and check auth_enable only once in sctp_endpoint_init().

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: sctp_sock_migrate() returns error if sctp_bind_addr_dup() fails

It should fail to create the new sk if sctp_bind_addr_dup() fails
when accepting or peeloff an association.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vxlan: Fix GRO cells race condition between receive and link delete

If we receive a packet while deleting a VXLAN device, there's a chance
vxlan_rcv() is called at the same time as vxlan_dellink(). This is fine,
except that vxlan_dellink() should never ever touch stuff that's still in
use, such as the GRO cells list.

Otherwise, vxlan_rcv() crashes while queueing packets via
gro_cells_receive().

Move the gro_cells_destroy() to vxlan_uninit(), which runs after the RCU
grace period is elapsed and nothing needs the gro_cells anymore.

This is now done in the same way as commit 8e816df87997 ("geneve: Use GRO
cells infrastructure.") originally implemented for GENEVE.

Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: 58ce31cca1ff ("vxlan: GRO support at tunnel layer")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rxrpc: Fix client call connect/disconnect race

rxrpc_disconnect_client_call() reads the call's connection ID protocol
value (call->cid) as part of that function's variable declarations. This
is bad because it's not inside the locked section and so may race with
someone granting use of the channel to the call.

This manifests as an assertion failure (see below) where the call in the
presumed channel (0 because call->cid wasn't set when we read it) doesn't
match the call attached to the channel we were actually granted (if 1, 2 or
3).

Fix this by moving the read and dependent calculations inside of the
channel_lock section. Also, only set the channel number and pointer
variables if cid is not zero (ie. unset).

This problem can be induced by injecting an occasional error in
rxrpc_wait_for_channel() before the call to schedule().

Make two further changes also:

(1) Add a trace for wait failure in rxrpc_connect_call().

(2) Drop channel_lock before BUG'ing in the case of the assertion failure.

The failure causes a trace akin to the following:

rxrpc: Assertion failed - 18446612685268945920(0xffff8880beab8c00) == 18446612685268621312(0xffff8880bea69800) is false
------------[ cut here ]------------
kernel BUG at net/rxrpc/conn_client.c:824!
...
RIP: 0010:rxrpc_disconnect_client_call+0x2bf/0x99d
...
Call Trace:
rxrpc_connect_call+0x902/0x9b3
? wake_up_q+0x54/0x54
rxrpc_new_client_call+0x3a0/0x751
? rxrpc_kernel_begin_call+0x141/0x1bc
? afs_alloc_call+0x1b5/0x1b5
rxrpc_kernel_begin_call+0x141/0x1bc
afs_make_call+0x20c/0x525
? afs_alloc_call+0x1b5/0x1b5
? __lock_is_held+0x40/0x71
? lockdep_init_map+0xaf/0x193
? lockdep_init_map+0xaf/0x193
? __lock_is_held+0x40/0x71
? yfs_fs_fetch_data+0x33b/0x34a
yfs_fs_fetch_data+0x33b/0x34a
afs_fetch_data+0xdc/0x3b7
afs_read_dir+0x52d/0x97f
afs_dir_iterate+0xa0/0x661
? iterate_dir+0x63/0x141
iterate_dir+0xa2/0x141
ksys_getdents64+0x9f/0x11b
? filldir+0x111/0x111
? do_syscall_64+0x3e/0x1a0
__x64_sys_getdents64+0x16/0x19
do_syscall_64+0x7d/0x1a0
entry_SYSCALL_64_after_hwframe+0x49/0xbe

Fixes: 45025bceef17 ("rxrpc: Improve management and caching of client connection objects")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sctp: remove sched init from sctp_stream_init

syzbot reported a NULL-ptr deref caused by that sched->init() in
sctp_stream_init() set stream->rr_next = NULL.

  kasan: GPF could be caused by NULL-ptr deref or user memory access
  RIP: 0010:sctp_sched_rr_dequeue+0xd3/0x170 net/sctp/stream_sched_rr.c:141
  Call Trace:
    sctp_outq_dequeue_data net/sctp/outqueue.c:90 [inline]
    sctp_outq_flush_data net/sctp/outqueue.c:1079 [inline]
    sctp_outq_flush+0xba2/0x2790 net/sctp/outqueue.c:1205

All sched info is saved in sout->ext now, in sctp_stream_init()
sctp_stream_alloc_out() will not change it, there's no need to
call sched->init() again, since sctp_outq_init() has already
done it.

Fixes: 5bbbbe32a431 ("sctp: introduce stream scheduler foundations")
Reported-by: syzbot+4c9934f20522c0efd657@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

route: set the deleted fnhe fnhe_daddr to 0 in ip_del_fnhe to fix a race

The race occurs in __mkroute_output() when 2 threads lookup a dst:

  CPU A                 CPU B
  find_exception()
                        find_exception() [fnhe expires]
                        ip_del_fnhe() [fnhe is deleted]
  rt_bind_exception()

In rt_bind_exception() it will bind a deleted fnhe with the new dst, and
this dst will get no chance to be freed. It causes a dev defcnt leak and
consecutive dmesg warnings:

  unregister_netdevice: waiting for ethX to become free. Usage count = 1

Especially thanks Jon to identify the issue.

This patch fixes it by setting fnhe_daddr to 0 in ip_del_fnhe() to stop
binding the deleted fnhe with a new dst when checking fnhe's fnhe_daddr
and daddr in rt_bind_exception().

It works as both ip_del_fnhe() and rt_bind_exception() are protected by
fnhe_lock and the fhne is freed by kfree_rcu().

Fixes: deed49df7390 ("route: check and remove route cache when we get route")
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/hsr: fix possible crash in add_timer()

syzbot found another add_timer() issue, this time in net/hsr [1]

Let's use mod_timer() which is safe.

[1]
kernel BUG at kernel/time/timer.c:1136!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 15909 Comm: syz-executor.3 Not tainted 5.0.0+ #97
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
kobject: 'loop2' (00000000f5629718): kobject_uevent_env
RIP: 0010:add_timer kernel/time/timer.c:1136 [inline]
RIP: 0010:add_timer+0x654/0xbe0 kernel/time/timer.c:1134
Code: 0f 94 c5 31 ff 44 89 ee e8 09 61 0f 00 45 84 ed 0f 84 77 fd ff ff e8 bb 5f 0f 00 e8 07 10 a0 ff e9 68 fd ff ff e8 ac 5f 0f 00 <0f> 0b e8 a5 5f 0f 00 0f 0b e8 9e 5f 0f 00 4c 89 b5 58 ff ff ff e9
RSP: 0018:ffff8880656eeca0 EFLAGS: 00010246
kobject: 'loop2' (00000000f5629718): fill_kobj_path: path = '/devices/virtual/block/loop2'
RAX: 0000000000040000 RBX: 1ffff1100caddd9a RCX: ffffc9000c436000
RDX: 0000000000040000 RSI: ffffffff816056c4 RDI: ffff88806a2f6cc8
RBP: ffff8880656eed58 R08: ffff888067f4a300 R09: ffff888067f4abc8
R10: 0000000000000000 R11: 0000000000000000 R12: ffff88806a2f6cc0
R13: dffffc0000000000 R14: 0000000000000001 R15: ffff8880656eed30
FS: 00007fc2019bf700(0000) GS:ffff8880ae800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000738000 CR3: 0000000067e8e000 CR4: 00000000001406f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
hsr_check_announce net/hsr/hsr_device.c:99 [inline]
hsr_check_carrier_and_operstate+0x567/0x6f0 net/hsr/hsr_device.c:120
hsr_netdev_notify+0x297/0xa00 net/hsr/hsr_main.c:51
notifier_call_chain+0xc7/0x240 kernel/notifier.c:93
__raw_notifier_call_chain kernel/notifier.c:394 [inline]
raw_notifier_call_chain+0x2e/0x40 kernel/notifier.c:401
call_netdevice_notifiers_info+0x3f/0x90 net/core/dev.c:1739
call_netdevice_notifiers_extack net/core/dev.c:1751 [inline]
call_netdevice_notifiers net/core/dev.c:1765 [inline]
dev_open net/core/dev.c:1436 [inline]
dev_open+0x143/0x160 net/core/dev.c:1424
team_port_add drivers/net/team/team.c:1203 [inline]
team_add_slave+0xa07/0x15d0 drivers/net/team/team.c:1933
do_set_master net/core/rtnetlink.c:2358 [inline]
do_set_master+0x1d4/0x230 net/core/rtnetlink.c:2332
do_setlink+0x966/0x3510 net/core/rtnetlink.c:2493
rtnl_setlink+0x271/0x3b0 net/core/rtnetlink.c:2747
rtnetlink_rcv_msg+0x465/0xb00 net/core/rtnetlink.c:5192
netlink_rcv_skb+0x17a/0x460 net/netlink/af_netlink.c:2485
rtnetlink_rcv+0x1d/0x30 net/core/rtnetlink.c:5210
netlink_unicast_kernel net/netlink/af_netlink.c:1310 [inline]
netlink_unicast+0x536/0x720 net/netlink/af_netlink.c:1336
netlink_sendmsg+0x8ae/0xd70 net/netlink/af_netlink.c:1925
sock_sendmsg_nosec net/socket.c:622 [inline]
sock_sendmsg+0xdd/0x130 net/socket.c:632
sock_write_iter+0x27c/0x3e0 net/socket.c:923
call_write_iter include/linux/fs.h:1869 [inline]
do_iter_readv_writev+0x5e0/0x8e0 fs/read_write.c:680
do_iter_write fs/read_write.c:956 [inline]
do_iter_write+0x184/0x610 fs/read_write.c:937
vfs_writev+0x1b3/0x2f0 fs/read_write.c:1001
do_writev+0xf6/0x290 fs/read_write.c:1036
__do_sys_writev fs/read_write.c:1109 [inline]
__se_sys_writev fs/read_write.c:1106 [inline]
__x64_sys_writev+0x75/0xb0 fs/read_write.c:1106
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x457f29
Code: ad b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007fc2019bec78 EFLAGS: 00000246 ORIG_RAX: 0000000000000014
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000457f29
RDX: 0000000000000001 RSI: 00000000200000c0 RDI: 0000000000000003
RBP: 000000000073bf00 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007fc2019bf6d4
R13: 00000000004c4a60 R14: 00000000004dd218 R15: 00000000ffffffff

Fixes: f421436a591d ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

nfp: fix simple vNIC mailbox length

The simple vNIC mailbox length should be 12 decimal and not 0x12.
Using a decimal also makes it clear this is a length value and not
another field within the simple mailbox defines.

Found by code inspection, there are no known firmware configurations
where this would cause issues.

Fixes: 527d7d1b9949 ("nfp: read mailbox address from TLV caps")
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: atm: Add another IS_ENABLED(CONFIG_COMPAT) in atm_dev_ioctl

I removed compat's universal assignment to 0, which allows this if
statement to fall through when compat is passed with a value other
than 0.

Fixes: f9d19a7494e5 ("net: atm: Use IS_ENABLED in atm_dev_ioctl")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: stmmac: Avoid sometimes uninitialized Clang warnings

When building with -Wsometimes-uninitialized, Clang warns:

drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:495:3: warning: variable 'ns' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:495:3: warning: variable 'ns' is used uninitialized whenever '&&' condition is false [-Wsometimes-uninitialized]
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:532:3: warning: variable 'ns' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:532:3: warning: variable 'ns' is used uninitialized whenever '&&' condition is false [-Wsometimes-uninitialized]
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:741:3: warning: variable 'sec_inc' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:741:3: warning: variable 'sec_inc' is used uninitialized whenever '&&' condition is false [-Wsometimes-uninitialized]

Clang is concerned with the use of stmmac_do_void_callback (which
stmmac_get_timestamp and stmmac_config_sub_second_increment wrap),
as it may fail to initialize these values if the if condition was ever
false (meaning the callbacks don't exist). It's not wrong because the
callbacks (get_timestamp and config_sub_second_increment respectively)
are the ones that initialize the variables. While it's unlikely that the
callbacks are ever going to disappear and make that condition false, we
can easily avoid this warning by zero initialize the variables.

Link: https://github.com/ClangBuiltLinux/linux/issues/384
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: atm: Use IS_ENABLED in atm_dev_ioctl

When building with -Wsometimes-uninitialized, Clang warns:

net/atm/resources.c:256:6: warning: variable 'number' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized]
net/atm/resources.c:212:7: warning: variable 'iobuf_len' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized]

Clang won't realize that compat is 0 when CONFIG_COMPAT is not set until
the constant folding stage, which happens after this semantic analysis.
Use IS_ENABLED instead so that the zero is present at the semantic
analysis stage, which eliminates this warning.

Link: https://github.com/ClangBuiltLinux/linux/issues/386
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool: reduce stack usage with clang

clang inlines the dev_ethtool() more aggressively than gcc does, leading
to a larger amount of used stack space:

net/core/ethtool.c:2536:24: error: stack frame size of 1216 bytes in function 'dev_ethtool' [-Werror,-Wframe-larger-than=]

Marking the sub-functions that require the most stack space as
noinline_for_stack gives us reasonable behavior on all compilers.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

qede: Fix internal loopback failure with jumbo mtu configuration

Driver uses port-mtu as packet-size for the loopback traffic. This patch
limits the max packet size to 1.5K to avoid data being split over multiple
buffer descriptors (BDs) in cases where MTU > PAGE_SIZE.

Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

enic: fix build warning without CONFIG_CPUMASK_OFFSTACK

The enic driver relies on the CONFIG_CPUMASK_OFFSTACK feature to
dynamically allocate a struct member, but this is normally intended for
local variables.

Building with clang, I get a warning for a few locations that check the
address of the cpumask_var_t:

drivers/net/ethernet/cisco/enic/enic_main.c:122:22: error: address of array 'enic->msix[i].affinity_mask' will always evaluate to 'true' [-Werror,-Wpointer-bool-conversion]

As far as I can tell, the code is still correct, as the truth value of
the pointer is what we need in this configuration. To get rid of
the warning, use cpumask_available() instead of checking the
pointer directly.

Fixes: 322cf7e3a4e8 ("enic: assign affinity hint to interrupts")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

peak_usb: fix clang build warning

Clang points out undefined behavior when building the pcan_usb_pro driver:

drivers/net/can/usb/peak_usb/pcan_usb_pro.c:136:15: error: passing an object that undergoes default argument promotion to 'va_start' has undefined behavior [-Werror,-Wvarargs]

Changing the function prototype to avoid argument promotion in the
varargs call avoids the warning, and should make this well-defined.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ravb: Decrease TxFIFO depth of Q3 and Q2 to one

Hardware has the CBS (Credit Based Shaper) which affects only Q3
and Q2. When updating the CBS settings, even if the driver does so
after waiting for Tx DMA finished, there is a possibility that frame
data still remains in TxFIFO.

To avoid this, decrease TxFIFO depth of Q3 and Q2 to one.

This patch has been exercised this using netperf TCP_MAERTS, TCP_STREAM
and UDP_STREAM tests run on an Ebisu board. No performance change was
detected, outside of noise in the tests, both in terms of throughput and
CPU utilisation.

Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
[simon: updated changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

isdn: isdnloop: fix pointer dereference bug

clang has spotted an ancient code bug and warns about it with:

drivers/isdn/isdnloop/isdnloop.c:573:12: error: address of array 'card->rcard' will always evaluate to 'true' [-Werror,-Wpointer-bool-conversion]

This is an array of pointers, so we should check if a specific
pointer exists in the array before using it, not whether the
array itself exists.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

davinci_emac: always build in CONFIG_OF code

clang warns about what seems to be an unintended use of an obscure C
language feature where a forward declaration of an array remains usable
when the final definition is never seen:

drivers/net/ethernet/ti/davinci_emac.c:1694:34: error: tentative array definition assumed to have one element [-Werror]
static const struct of_device_id davinci_emac_of_match[];

There is no harm in always enabling the device tree matching code here,
and it makes the code behave in a more conventional way aside from
avoiding the warning.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bpf: fix replace_map_fd_with_map_ptr's ldimm64 second imm field

Non-zero imm value in the second part of the ldimm64 instruction for
BPF_PSEUDO_MAP_FD is invalid, and thus must be rejected. The map fd
only ever sits in the first instructions' imm field. None of the BPF
loaders known to us are using it, so risk of regression is minimal.
For clarity and consistency, the few insn->{src_reg,imm} occurrences
are rewritten into insn[0].{src_reg,imm}. Add a test case to the BPF
selftest suite as well.

Fixes: 0246e64d9a5f ("bpf: handle pseudo BPF_LD_IMM64 insn")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

bpf: Stop the psock parser before canceling its work

We might have never enabled (started) the psock's parser, in which case it
will not get stopped when destroying the psock. This leads to a warning
when trying to cancel parser's work from psock's deferred destructor:

[  405.325769] WARNING: CPU: 1 PID: 3216 at net/strparser/strparser.c:526 strp_done+0x3c/0x40
[  405.326712] Modules linked in: [last unloaded: test_bpf]
[  405.327359] CPU: 1 PID: 3216 Comm: kworker/1:164 Tainted: G        W         5.0.0 #42
[  405.328294] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ?-20180531_142017-buildhw-08.phx2.fedoraproject.org-1.fc28 04/01/2014
[  405.329712] Workqueue: events sk_psock_destroy_deferred
[  405.330254] RIP: 0010:strp_done+0x3c/0x40
[  405.330706] Code: 28 e8 b8 d5 6b ff 48 8d bb 80 00 00 00 e8 9c d5 6b ff 48 8b 7b 18 48 85 ff 74 0d e8 1e a5 e8 ff 48 c7 43 18 00 00 00 00 5b c3 <0f> 0b eb cf 66 66 66 66 90 55 89 f5 53 48 89 fb 48 83 c7 28 e8 0b
[  405.332862] RSP: 0018:ffffc900026bbe50 EFLAGS: 00010246
[  405.333482] RAX: ffffffff819323e0 RBX: ffff88812cb83640 RCX: ffff88812cb829e8
[  405.334228] RDX: 0000000000000001 RSI: ffff88812cb837e8 RDI: ffff88812cb83640
[  405.335366] RBP: ffff88813fd22680 R08: 0000000000000000 R09: 000073746e657665
[  405.336472] R10: 8080808080808080 R11: 0000000000000001 R12: ffff88812cb83600
[  405.337760] R13: 0000000000000000 R14: ffff88811f401780 R15: ffff88812cb837e8
[  405.338777] FS:  0000000000000000(0000) GS:ffff88813fd00000(0000) knlGS:0000000000000000
[  405.339903] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  405.340821] CR2: 00007fb11489a6b8 CR3: 000000012d4d6000 CR4: 00000000000406e0
[  405.341981] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  405.343131] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  405.344415] Call Trace:
[  405.344821]  sk_psock_destroy_deferred+0x23/0x1b0
[  405.345585]  process_one_work+0x1ae/0x3e0
[  405.346110]  worker_thread+0x3c/0x3b0
[  405.346576]  ? pwq_unbound_release_workfn+0xd0/0xd0
[  405.347187]  kthread+0x11d/0x140
[  405.347601]  ? __kthread_parkme+0x80/0x80
[  405.348108]  ret_from_fork+0x35/0x40
[  405.348566] ---[ end trace a4a3af4026a327d4 ]---

Stop psock's parser just before canceling its work.

Fixes: 1d79895aef18 ("sk_msg: Always cancel strp work before freeing the psock")
Reported-by: kernel test robot <rong.a.chen@intel.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

selftests: bpf: test_progs: initialize duration in singal_pending test

CHECK macro implicitly uses duration. We call CHECK() a couple of times
before duration is initialized from bpf_prog_test_run().
Explicitly set duration to 0 to avoid compiler warnings.

Fixes: 740f8a657221 ("selftests/bpf: make sure signal interrupts BPF_PROG_TEST_RUN")
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

libbpf: force fixdep compilation at the start of the build

libbpf targets don't explicitly depend on fixdep target, so when
we do 'make -j$(nproc)', there is a high probability, that some
objects will be built before fixdep binary is available.

Fix this by running sub-make; this makes sure that fixdep dependency
is properly accounted for.

For the same issue in perf, see commit abb26210a395 ("perf tools: Force
fixdep compilation at the start of the build").

Before:

$ rm -rf /tmp/bld; mkdir /tmp/bld; make -j$(nproc) O=/tmp/bld -C tools/lib/bpf/

Auto-detecting system features:
...                        libelf: [ on  ]
...                           bpf: [ on  ]

  HOSTCC   /tmp/bld/fixdep.o
  CC       /tmp/bld/libbpf.o
  CC       /tmp/bld/bpf.o
  CC       /tmp/bld/btf.o
  CC       /tmp/bld/nlattr.o
  CC       /tmp/bld/libbpf_errno.o
  CC       /tmp/bld/str_error.o
  CC       /tmp/bld/netlink.o
  CC       /tmp/bld/bpf_prog_linfo.o
  CC       /tmp/bld/libbpf_probes.o
  CC       /tmp/bld/xsk.o
  HOSTLD   /tmp/bld/fixdep-in.o
  LINK     /tmp/bld/fixdep
  LD       /tmp/bld/libbpf-in.o
  LINK     /tmp/bld/libbpf.a
  LINK     /tmp/bld/libbpf.so
  LINK     /tmp/bld/test_libbpf

$ head /tmp/bld/.libbpf.o.cmd
# cannot find fixdep (/usr/local/google/home/sdf/src/linux/xxx//fixdep)
# using basic dep data

/tmp/bld/libbpf.o: libbpf.c /usr/include/stdc-predef.h \
/usr/include/stdlib.h /usr/include/features.h \
/usr/include/x86_64-linux-gnu/sys/cdefs.h \
/usr/include/x86_64-linux-gnu/bits/wordsize.h \
/usr/include/x86_64-linux-gnu/gnu/stubs.h \
/usr/include/x86_64-linux-gnu/gnu/stubs-64.h \
/usr/lib/gcc/x86_64-linux-gnu/7/include/stddef.h \

After:

$ rm -rf /tmp/bld; mkdir /tmp/bld; make -j$(nproc) O=/tmp/bld -C tools/lib/bpf/

Auto-detecting system features:
...                        libelf: [ on  ]
...                           bpf: [ on  ]

  HOSTCC   /tmp/bld/fixdep.o
  HOSTLD   /tmp/bld/fixdep-in.o
  LINK     /tmp/bld/fixdep
  CC       /tmp/bld/libbpf.o
  CC       /tmp/bld/bpf.o
  CC       /tmp/bld/nlattr.o
  CC       /tmp/bld/btf.o
  CC       /tmp/bld/libbpf_errno.o
  CC       /tmp/bld/str_error.o
  CC       /tmp/bld/netlink.o
  CC       /tmp/bld/bpf_prog_linfo.o
  CC       /tmp/bld/libbpf_probes.o
  CC       /tmp/bld/xsk.o
  LD       /tmp/bld/libbpf-in.o
  LINK     /tmp/bld/libbpf.a
  LINK     /tmp/bld/libbpf.so
  LINK     /tmp/bld/test_libbpf

$ head /tmp/bld/.libbpf.o.cmd
cmd_/tmp/bld/libbpf.o := gcc -Wp,-MD,/tmp/bld/.libbpf.o.d -Wp,-MT,/tmp/bld/libbpf.o -g -Wall -DHAVE_LIBELF_MMAP_SUPPORT -DCOMPAT_NEED_REALLOCARRAY -Wbad-function-cast -Wdeclaration-after-statement -Wformat-security -Wformat-y2k -Winit-self -Wmissing-declarations -Wmissing-prototypes -Wnested-externs -Wno-system-headers -Wold-style-definition -Wpacked -Wredundant-decls -Wshadow -Wstrict-prototypes -Wswitch-default -Wswitch-enum -Wundef -Wwrite-strings -Wformat -Wstrict-aliasing=3 -Werror -Wall -fPIC -I. -I/usr/local/google/home/sdf/src/linux/tools/include -I/usr/local/google/home/sdf/src/linux/tools/arch/x86/include/uapi -I/usr/local/google/home/sdf/src/linux/tools/include/uapi -fvisibility=hidden -D"BUILD_STR(s)=$(pound)s" -c -o /tmp/bld/libbpf.o libbpf.c

source_/tmp/bld/libbpf.o := libbpf.c

deps_/tmp/bld/libbpf.o := \
  /usr/include/stdc-predef.h \
  /usr/include/stdlib.h \
  /usr/include/features.h \
  /usr/include/x86_64-linux-gnu/sys/cdefs.h \
  /usr/include/x86_64-linux-gnu/bits/wordsize.h \

Fixes: 7c422f557266 ("tools build: Build fixdep helper from perf and basic libs")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

selftests: bpf: fix compilation with out-of-tree $(OUTPUT)

A bunch of related changes lumped together:
* Create prog_tests and verifier output directories; these don't exist with
out-of-tree $(OUTPUT)
* Add missing -I (via separate TEST_{PROGS,VERIFIER}_CFLAGS) for the main tree
($(PWD) != $(OUTPUT) for out-of-tree)
* Add libbpf.a dependency for test_progs_32 (parallel make fails otherwise)
* Add missing "; \" after "cd" when generating test.h headers

Tested by:
$ alias m="make -s -j$(nproc)"
$ m -C tools/testing/selftests/bpf/ clean
$ m -C tools/lib/bpf/ clean
$ rm -rf xxx; mkdir xxx; m -C tools/testing/selftests/bpf/ OUTPUT=$PWD/xxx
$ m -C tools/testing/selftests/bpf/

Fixes: 3f30658830f3 ("selftests: bpf: break up test_progs - preparations")
Fixes: 2dfb40121ee8 ("selftests: bpf: prepare for break up of verifier tests")
Fixes: 3ef84346c561 ("selftests: bpf: makefile support sub-register code-gen test mode")
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

selftests/bpf: test that GSO works in lwt_ip_encap

Add a test on egress that a large TCP packet successfully goes through
the lwt+bpf encap tunnel.

Although there is no direct evidence that GSO worked, as opposed to
e.g. TCP segmentation or IP fragmentation (maybe a kernel stats counter
should be added to track the number of failed GSO attempts?), without
the previous patch in the patchset this test fails, and printk-debugging
showed that software-based GSO succeeded here (veth is not compatible with
SKB_GSO_DODGY, so GSO happens in the software stack).

Also removed an unnecessary nodad and added a missed failed flag.

Signed-off-by: Peter Oskolkov <posk@google.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

net: fix GSO in bpf_lwt_push_ip_encap

GSO needs inner headers and inner protocol set properly to work.

skb->inner_mac_header: skb_reset_inner_headers() assigns the current
mac header value to inner_mac_header; but it is not set at the point,
so we need to call skb_reset_inner_mac_header, otherwise gre_gso_segment
fails: it does

    int tnl_hlen = skb_inner_mac_header(skb) - skb_transport_header(skb);
    ...
    if (unlikely(!pskb_may_pull(skb, tnl_hlen)))
    ...

skb->inner_protocol should also be correctly set.

Fixes: ca78801a81e0 ("bpf: handle GSO in bpf_lwt_push_encap")
Signed-off-by: Peter Oskolkov <posk@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

xsk: fix potential crash in xsk_diag_put_umem()

Fixes two typos in xsk_diag_put_umem()

syzbot reported the following crash :

kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
CPU: 1 PID: 7641 Comm: syz-executor946 Not tainted 5.0.0-rc7+ #95
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:xsk_diag_put_umem net/xdp/xsk_diag.c:71 [inline]
RIP: 0010:xsk_diag_fill net/xdp/xsk_diag.c:113 [inline]
RIP: 0010:xsk_diag_dump+0xdcb/0x13a0 net/xdp/xsk_diag.c:143
Code: 8d be c0 04 00 00 48 89 f8 48 c1 e8 03 42 80 3c 20 00 0f 85 39 04 00 00 49 8b 96 c0 04 00 00 48 8d 7a 14 48 89 f8 48 c1 e8 03 <42> 0f b6 0c 20 48 89 f8 83 e0 07 83 c0 03 38 c8 7c 08 84 c9 0f 85
RSP: 0018:ffff888090bcf2d8 EFLAGS: 00010203
RAX: 0000000000000002 RBX: ffff8880a0aacbc0 RCX: ffffffff86ffdc3c
RDX: 0000000000000000 RSI: ffffffff86ffdc70 RDI: 0000000000000014
RBP: ffff888090bcf438 R08: ffff88808e04a700 R09: ffffed1011c74174
R10: ffffed1011c74173 R11: ffff88808e3a0b9f R12: dffffc0000000000
R13: ffff888093a6d818 R14: ffff88808e365240 R15: ffff88808e3a0b40
FS:  00000000011ea880(0000) GS:ffff8880ae900000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020000080 CR3: 000000008fa13000 CR4: 00000000001406e0
Call Trace:
netlink_dump+0x55d/0xfb0 net/netlink/af_netlink.c:2252
__netlink_dump_start+0x5b4/0x7e0 net/netlink/af_netlink.c:2360
netlink_dump_start include/linux/netlink.h:226 [inline]
xsk_diag_handler_dump+0x1b2/0x250 net/xdp/xsk_diag.c:170
__sock_diag_cmd net/core/sock_diag.c:232 [inline]
sock_diag_rcv_msg+0x322/0x410 net/core/sock_diag.c:263
netlink_rcv_skb+0x17a/0x460 net/netlink/af_netlink.c:2485
sock_diag_rcv+0x2b/0x40 net/core/sock_diag.c:274
netlink_unicast_kernel net/netlink/af_netlink.c:1310 [inline]
netlink_unicast+0x536/0x720 net/netlink/af_netlink.c:1336
netlink_sendmsg+0x8ae/0xd70 net/netlink/af_netlink.c:1925
sock_sendmsg_nosec net/socket.c:622 [inline]
sock_sendmsg+0xdd/0x130 net/socket.c:632
sock_write_iter+0x27c/0x3e0 net/socket.c:923
call_write_iter include/linux/fs.h:1863 [inline]
do_iter_readv_writev+0x5e0/0x8e0 fs/read_write.c:680
do_iter_write fs/read_write.c:956 [inline]
do_iter_write+0x184/0x610 fs/read_write.c:937
vfs_writev+0x1b3/0x2f0 fs/read_write.c:1001
do_writev+0xf6/0x290 fs/read_write.c:1036
__do_sys_writev fs/read_write.c:1109 [inline]
__se_sys_writev fs/read_write.c:1106 [inline]
__x64_sys_writev+0x75/0xb0 fs/read_write.c:1106
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x440139
Code: 18 89 d0 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 fb 13 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007ffcc966cc18 EFLAGS: 00000246 ORIG_RAX: 0000000000000014
RAX: ffffffffffffffda RBX: 00000000004002c8 RCX: 0000000000440139
RDX: 0000000000000001 RSI: 0000000020000080 RDI: 0000000000000003
RBP: 00000000006ca018 R08: 00000000004002c8 R09: 00000000004002c8
R10: 0000000000000004 R11: 0000000000000246 R12: 00000000004019c0
R13: 0000000000401a50 R14: 0000000000000000 R15: 0000000000000000
Modules linked in:
---[ end trace 460a3c24d0a656c9 ]---
RIP: 0010:xsk_diag_put_umem net/xdp/xsk_diag.c:71 [inline]
RIP: 0010:xsk_diag_fill net/xdp/xsk_diag.c:113 [inline]
RIP: 0010:xsk_diag_dump+0xdcb/0x13a0 net/xdp/xsk_diag.c:143
Code: 8d be c0 04 00 00 48 89 f8 48 c1 e8 03 42 80 3c 20 00 0f 85 39 04 00 00 49 8b 96 c0 04 00 00 48 8d 7a 14 48 89 f8 48 c1 e8 03 <42> 0f b6 0c 20 48 89 f8 83 e0 07 83 c0 03 38 c8 7c 08 84 c9 0f 85
RSP: 0018:ffff888090bcf2d8 EFLAGS: 00010203
RAX: 0000000000000002 RBX: ffff8880a0aacbc0 RCX: ffffffff86ffdc3c
RDX: 0000000000000000 RSI: ffffffff86ffdc70 RDI: 0000000000000014
RBP: ffff888090bcf438 R08: ffff88808e04a700 R09: ffffed1011c74174
R10: ffffed1011c74173 R11: ffff88808e3a0b9f R12: dffffc0000000000
R13: ffff888093a6d818 R14: ffff88808e365240 R15: ffff88808e3a0b40
FS:  00000000011ea880(0000) GS:ffff8880ae800000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000001d22000 CR3: 000000008fa13000 CR4: 00000000001406f0

Fixes: a36b38aa2af6 ("xsk: add sock_diag interface for AF_XDP")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Björn Töpel <bjorn.topel@intel.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Magnus Karlsson <magnus.karlsson@intel.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

bpf: hbm: fix spelling mistake "deault" -> "default"

There are a couple of typos, fix these.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

bpf: only test gso type on gso packets

BPF can adjust gso only for tcp bytestreams. Fail on other gso types.

But only on gso packets. It does not touch this field if !gso_size.

Fixes: b90efd225874 ("bpf: only adjust gso_size on bytestream protocols")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

bpf: fix sysctl.c warning

When CONFIG_BPF_SYSCALL or CONFIG_SYSCTL is disabled, we get
a warning about an unused function:

kernel/sysctl.c:3331:12: error: 'proc_dointvec_minmax_bpf_stats' defined but not used [-Werror=unused-function]
static int proc_dointvec_minmax_bpf_stats(struct ctl_table *table, int write,

The CONFIG_BPF_SYSCALL check was already handled, but the SYSCTL check
is needed on top.

Fixes: 492ecee892c2 ("bpf: enable program stats")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Christian Brauner <christian@brauner.io>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

tcp: do not report TCP_CM_INQ of 0 for closed connections

Returning 0 as inq to userspace indicates there is no more data to
read, and the application needs to wait for EPOLLIN. For a connection
that has received FIN from the remote peer, however, the application
must continue reading until getting EOF (return value of 0
from tcp_recvmsg) or an error, if edge-triggered epoll (EPOLLET) is
being used. Otherwise, the application will never receive a new
EPOLLIN, since there is no epoll edge after the FIN.

Return 1 when there is no data left on the queue but the
connection has received FIN, so that the applications continue
reading.

Fixes: b75eba76d3d72 (tcp: send in-queue bytes in cmsg upon read)
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hsr: fix memory leak in hsr_dev_finalize()

If hsr_add_port(hsr, hsr_dev, HSR_PT_MASTER) failed to
add port, it directly returns res and forgets to free the node
that allocated in hsr_create_self_node(), and forgets to delete
the node->mac_list linked in hsr->self_node_db.

BUG: memory leak
unreferenced object 0xffff8881cfa0c780 (size 64):
  comm "syz-executor.0", pid 2077, jiffies 4294717969 (age 2415.377s)
  hex dump (first 32 bytes):
    e0 c7 a0 cf 81 88 ff ff 00 02 00 00 00 00 ad de  ................
    00 e6 49 cd 81 88 ff ff c0 9b 87 d0 81 88 ff ff  ..I.............
  backtrace:
    [<00000000e2ff5070>] hsr_dev_finalize+0x736/0x960 [hsr]
    [<000000003ed2e597>] hsr_newlink+0x2b2/0x3e0 [hsr]
    [<000000003fa8c6b6>] __rtnl_newlink+0xf1f/0x1600 net/core/rtnetlink.c:3182
    [<000000001247a7ad>] rtnl_newlink+0x66/0x90 net/core/rtnetlink.c:3240
    [<00000000e7d1b61d>] rtnetlink_rcv_msg+0x54e/0xb90 net/core/rtnetlink.c:5130
    [<000000005556bd3a>] netlink_rcv_skb+0x129/0x340 net/netlink/af_netlink.c:2477
    [<00000000741d5ee6>] netlink_unicast_kernel net/netlink/af_netlink.c:1310 [inline]
    [<00000000741d5ee6>] netlink_unicast+0x49a/0x650 net/netlink/af_netlink.c:1336
    [<000000009d56f9b7>] netlink_sendmsg+0x88b/0xdf0 net/netlink/af_netlink.c:1917
    [<0000000046b35c59>] sock_sendmsg_nosec net/socket.c:621 [inline]
    [<0000000046b35c59>] sock_sendmsg+0xc3/0x100 net/socket.c:631
    [<00000000d208adc9>] __sys_sendto+0x33e/0x560 net/socket.c:1786
    [<00000000b582837a>] __do_sys_sendto net/socket.c:1798 [inline]
    [<00000000b582837a>] __se_sys_sendto net/socket.c:1794 [inline]
    [<00000000b582837a>] __x64_sys_sendto+0xdd/0x1b0 net/socket.c:1794
    [<00000000c866801d>] do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290
    [<00000000fea382d9>] entry_SYSCALL_64_after_hwframe+0x49/0xbe
    [<00000000e01dacb3>] 0xffffffffffffffff

Fixes: c5a759117210 ("net/hsr: Use list_head (and rcu) instead of array for slave devices.")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sched: flower: insert new filter to idr after setting its mask

When adding new filter to flower classifier, fl_change() inserts it to
handle_idr before initializing filter extensions and assigning it a mask.
Normally this ordering doesn't matter because all flower classifier ops
callbacks assume rtnl lock protection. However, when filter has an action
that doesn't have its kernel module loaded, rtnl lock is released before
call to request_module(). During this time the filter can be accessed bu
concurrent task before its initialization is completed, which can lead to a
crash.

Example case of NULL pointer dereference in concurrent dump:

Task 1                           Task 2

tc_new_tfilter()
fl_change()
  idr_alloc_u32(fnew)
  fl_set_parms()
   tcf_exts_validate()
    tcf_action_init()
     tcf_action_init_1()
      rtnl_unlock()
      request_module()
      ...                        rtnl_lock()
       tc_dump_tfilter()
         tcf_chain_dump()
   fl_walk()
    idr_get_next_ul()
    tcf_node_dump()
     tcf_fill_node()
      fl_dump()
       mask = &f->mask->key; <- NULL ptr
      rtnl_lock()

Extension initialization and mask assignment don't depend on fnew->handle
that is allocated by idr_alloc_u32(). Move idr allocation code after action
creation and mask assignment in fl_change() to prevent concurrent access
to not fully initialized filter when rtnl lock is released to load action
module.

Fixes: 01683a146999 ("net: sched: refactor flower walk to iterate over idr")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: detecting the misuse of .sendpage for Slab objects

sendpage was not designed for processing of the Slab pages,
in some situations it can trigger BUG_ON on receiving side.

Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

appletalk: Add atalk.h header files to MAINTAINERS file

Add the path names here so that git-send-email can pick up the
netdev@vger.kernel.org Cc line automatically for a patch that
only touches the headers.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

appletalk: Fix compile regression

A bugfix just broke compilation of appletalk when CONFIG_SYSCTL
is disabled:

In file included from net/appletalk/ddp.c:65:
net/appletalk/ddp.c: In function 'atalk_init':
include/linux/atalk.h:164:34: error: expected expression before 'do'
#define atalk_register_sysctl()  do { } while(0)
                                  ^~
net/appletalk/ddp.c:1934:7: note: in expansion of macro 'atalk_register_sysctl'
  rc = atalk_register_sysctl();

This is easier to avoid by using conventional inline functions
as stubs rather than macros. The header already has inline
functions for other purposes, so I'm changing over all the
macros for consistency.

Fixes: 6377f787aeb9 ("appletalk: Fix use-after-free in atalk_proc_exit")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

iptunnel: NULL pointer deref for ip_md_tunnel_xmit

Naresh Kamboju noted the following oops during execution of selftest
tools/testing/selftests/bpf/test_tunnel.sh on x86_64:

[  274.120445] BUG: unable to handle kernel NULL pointer dereference
at 0000000000000000
[  274.128285] #PF error: [INSTR]
[  274.131351] PGD 8000000414a0e067 P4D 8000000414a0e067 PUD 3b6334067 PMD 0
[  274.138241] Oops: 0010 [#1] SMP PTI
[  274.141734] CPU: 1 PID: 11464 Comm: ping Not tainted
5.0.0-rc4-next-20190129 #1
[  274.149046] Hardware name: Supermicro SYS-5019S-ML/X11SSH-F, BIOS
2.0b 07/27/2017
[  274.156526] RIP: 0010:          (null)
[  274.160280] Code: Bad RIP value.
[  274.163509] RSP: 0018:ffffbc9681f83540 EFLAGS: 00010286
[  274.168726] RAX: 0000000000000000 RBX: ffffdc967fa80a18 RCX: 0000000000000000
[  274.175851] RDX: ffff9db2ee08b540 RSI: 000000000000000e RDI: ffffdc967fa809a0
[  274.182974] RBP: ffffbc9681f83580 R08: ffff9db2c4d62690 R09: 000000000000000c
[  274.190098] R10: 0000000000000000 R11: ffff9db2ee08b540 R12: ffff9db31ce7c000
[  274.197222] R13: 0000000000000001 R14: 000000000000000c R15: ffff9db3179cf400
[  274.204346] FS:  00007ff4ae7c5740(0000) GS:ffff9db31fa80000(0000)
knlGS:0000000000000000
[  274.212424] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  274.218162] CR2: ffffffffffffffd6 CR3: 00000004574da004 CR4: 00000000003606e0
[  274.225292] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  274.232416] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  274.239541] Call Trace:
[  274.241988]  ? tnl_update_pmtu+0x296/0x3b0
[  274.246085]  ip_md_tunnel_xmit+0x1bc/0x520
[  274.250176]  gre_fb_xmit+0x330/0x390
[  274.253754]  gre_tap_xmit+0x128/0x180
[  274.257414]  dev_hard_start_xmit+0xb7/0x300
[  274.261598]  sch_direct_xmit+0xf6/0x290
[  274.265430]  __qdisc_run+0x15d/0x5e0
[  274.269007]  __dev_queue_xmit+0x2c5/0xc00
[  274.273011]  ? dev_queue_xmit+0x10/0x20
[  274.276842]  ? eth_header+0x2b/0xc0
[  274.280326]  dev_queue_xmit+0x10/0x20
[  274.283984]  ? dev_queue_xmit+0x10/0x20
[  274.287813]  arp_xmit+0x1a/0xf0
[  274.290952]  arp_send_dst.part.19+0x46/0x60
[  274.295138]  arp_solicit+0x177/0x6b0
[  274.298708]  ? mod_timer+0x18e/0x440
[  274.302281]  neigh_probe+0x57/0x70
[  274.305684]  __neigh_event_send+0x197/0x2d0
[  274.309862]  neigh_resolve_output+0x18c/0x210
[  274.314212]  ip_finish_output2+0x257/0x690
[  274.318304]  ip_finish_output+0x219/0x340
[  274.322314]  ? ip_finish_output+0x219/0x340
[  274.326493]  ip_output+0x76/0x240
[  274.329805]  ? ip_fragment.constprop.53+0x80/0x80
[  274.334510]  ip_local_out+0x3f/0x70
[  274.337992]  ip_send_skb+0x19/0x40
[  274.341391]  ip_push_pending_frames+0x33/0x40
[  274.345740]  raw_sendmsg+0xc15/0x11d0
[  274.349403]  ? __might_fault+0x85/0x90
[  274.353151]  ? _copy_from_user+0x6b/0xa0
[  274.357070]  ? rw_copy_check_uvector+0x54/0x130
[  274.361604]  inet_sendmsg+0x42/0x1c0
[  274.365179]  ? inet_sendmsg+0x42/0x1c0
[  274.368937]  sock_sendmsg+0x3e/0x50
[  274.372460]  ___sys_sendmsg+0x26f/0x2d0
[  274.376293]  ? lock_acquire+0x95/0x190
[  274.380043]  ? __handle_mm_fault+0x7ce/0xb70
[  274.384307]  ? lock_acquire+0x95/0x190
[  274.388053]  ? __audit_syscall_entry+0xdd/0x130
[  274.392586]  ? ktime_get_coarse_real_ts64+0x64/0xc0
[  274.397461]  ? __audit_syscall_entry+0xdd/0x130
[  274.401989]  ? trace_hardirqs_on+0x4c/0x100
[  274.406173]  __sys_sendmsg+0x63/0xa0
[  274.409744]  ? __sys_sendmsg+0x63/0xa0
[  274.413488]  __x64_sys_sendmsg+0x1f/0x30
[  274.417405]  do_syscall_64+0x55/0x190
[  274.421064]  entry_SYSCALL_64_after_hwframe+0x49/0xbe
[  274.426113] RIP: 0033:0x7ff4ae0e6e87
[  274.429686] Code: 64 89 02 48 c7 c0 ff ff ff ff eb b9 0f 1f 80 00
00 00 00 8b 05 ca d9 2b 00 48 63 d2 48 63 ff 85 c0 75 10 b8 2e 00 00
00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 53 48 89 f3 48 83 ec 10 48 89 7c
24 08
[  274.448422] RSP: 002b:00007ffcd9b76db8 EFLAGS: 00000246 ORIG_RAX:
000000000000002e
[  274.455978] RAX: ffffffffffffffda RBX: 0000000000000040 RCX: 00007ff4ae0e6e87
[  274.463104] RDX: 0000000000000000 RSI: 00000000006092e0 RDI: 0000000000000003
[  274.470228] RBP: 0000000000000000 R08: 00007ffcd9bc40a0 R09: 00007ffcd9bc4080
[  274.477349] R10: 000000000000060a R11: 0000000000000246 R12: 0000000000000003
[  274.484475] R13: 0000000000000016 R14: 00007ffcd9b77fa0 R15: 00007ffcd9b78da4
[  274.491602] Modules linked in: cls_bpf sch_ingress iptable_filter
ip_tables algif_hash af_alg x86_pkg_temp_thermal fuse [last unloaded:
test_bpf]
[  274.504634] CR2: 0000000000000000
[  274.507976] ---[ end trace 196d18386545eae1 ]---
[  274.512588] RIP: 0010:          (null)
[  274.516334] Code: Bad RIP value.
[  274.519557] RSP: 0018:ffffbc9681f83540 EFLAGS: 00010286
[  274.524775] RAX: 0000000000000000 RBX: ffffdc967fa80a18 RCX: 0000000000000000
[  274.531921] RDX: ffff9db2ee08b540 RSI: 000000000000000e RDI: ffffdc967fa809a0
[  274.539082] RBP: ffffbc9681f83580 R08: ffff9db2c4d62690 R09: 000000000000000c
[  274.546205] R10: 0000000000000000 R11: ffff9db2ee08b540 R12: ffff9db31ce7c000
[  274.553329] R13: 0000000000000001 R14: 000000000000000c R15: ffff9db3179cf400
[  274.560456] FS:  00007ff4ae7c5740(0000) GS:ffff9db31fa80000(0000)
knlGS:0000000000000000
[  274.568541] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  274.574277] CR2: ffffffffffffffd6 CR3: 00000004574da004 CR4: 00000000003606e0
[  274.581403] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  274.588535] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  274.595658] Kernel panic - not syncing: Fatal exception in interrupt
[  274.602046] Kernel Offset: 0x14400000 from 0xffffffff81000000
(relocation range: 0xffffffff80000000-0xffffffffbfffffff)
[  274.612827] ---[ end Kernel panic - not syncing: Fatal exception in
interrupt ]---
[  274.620387] ------------[ cut here ]------------

I'm also seeing the same failure on x86_64, and it reproduces
consistently.

>From poking around it looks like the skb's dst entry is being used
to calculate the mtu in:

mtu = skb_dst(skb) ? dst_mtu(skb_dst(skb)) : dev->mtu;

...but because that dst_entry  has an "ops" value set to md_dst_ops,
the various ops (including mtu) are not set:

crash> struct sk_buff._skb_refdst ffff928f87447700 -x
      _skb_refdst = 0xffffcd6fbf5ea590
crash> struct dst_entry.ops 0xffffcd6fbf5ea590
  ops = 0xffffffffa0193800
crash> struct dst_ops.mtu 0xffffffffa0193800
  mtu = 0x0
crash>

I confirmed that the dst entry also has dst->input set to
dst_md_discard, so it looks like it's an entry that's been
initialized via __metadata_dst_init alright.

I think the fix here is to use skb_valid_dst(skb) - it checks
for  DST_METADATA also, and with that fix in place, the
problem - which was previously 100% reproducible - disappears.

The below patch resolves the panic and all bpf tunnel tests pass
without incident.

Fixes: c8b34e680a09 ("ip_tunnel: Add tnl_update_pmtu in ip_md_tunnel_xmit")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Tested-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv4/route: fail early when inet dev is missing

If a non local multicast packet reaches ip_route_input_rcu() while
the ingress device IPv4 private data (in_dev) is NULL, we end up
doing a NULL pointer dereference in IN_DEV_MFORWARD().

Since the later call to ip_route_input_mc() is going to fail if
!in_dev, we can fail early in such scenario and avoid the dangerous
code path.

v1 -> v2:
- clarified the commit message, no code changes

Reported-by: Tianhao Zhao <tizhao@redhat.com>
Fixes: e58e41596811 ("net: Enable support for VRF with ipv4 multicast")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: Fix a logical vs bitwise typo

There were a couple logical ORs accidentally mixed in with the bitwise
ORs.

Fixes: e8149933b1fa ("net: hns3: remove hnae3_get_bit in data path")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/sched: act_tunnel_key: Fix double free dst_cache

dst_cache_destroy will be called in dst_release

dst_release-->dst_destroy_rcu-->dst_destroy-->metadata_dst_free
-->dst_cache_destroy

It should not call dst_cache_destroy before dst_release

Fixes: 41411e2fd6b8 ("net/sched: act_tunnel_key: Add dst_cache support")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: fix RDM/DGRAM connect() regression

Fix regression bug introduced in
commit 365ad353c256 ("tipc: reduce risk of user starvation during link
congestion")

Only signal -EDESTADDRREQ for RDM/DGRAM if we don't have a cached
sockaddr.

Fixes: 365ad353c256 ("tipc: reduce risk of user starvation during link congestion")
Signed-off-by: Erik Hugne <erik.hugne@gmail.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mips_5.1' of git://git./linux/kernel/git/mips/linux

Pull MIPS updates from Paul Burton:

- Support for the MIPSr6 MemoryMapID register & Global INValidate TLB
   (GINVT) instructions, allowing for more efficient TLB maintenance
   when running on a CPU such as the I6500 that supports these.

- Enable huge page support for MIPS64r6.

- Optimize post-DMA cache sync by removing that code entirely for
   kernel configurations in which we know it won't be needed.

- The number of pages allocated for interrupt stacks is now calculated
   correctly, where before we would wastefully allocate too much memory
   in some configurations.

- The ath79 platform migrates to devicetree.

- The bcm47xx platform sees fixes for the Buffalo WHR-G54S board.

- The ingenic/jz4740 platform gains support for appended devicetrees.

- The cavium_octeon, lantiq, loongson32 & sgi-ip27 platforms all see
   cleanups as do various pieces of core architecture code.

* tag 'mips_5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (66 commits)
  MIPS: lantiq: Remove separate GPHY Firmware loader
  MIPS: ingenic: Add support for appended devicetree
  MIPS: SGI-IP27: rework HUB interrupts
  MIPS: SGI-IP27: do boot CPU init later
  MIPS: SGI-IP27: do xtalk scanning later
  MIPS: SGI-IP27: use pr_info/pr_emerg and pr_cont to fix output
  MIPS: SGI-IP27: clean up bridge access and header files
  MIPS: SGI-IP27: get rid of volatile and hubreg_t
  MIPS: irq: Allocate accurate order pages for irq stack
  MIPS: dma-noncoherent: Remove bogus condition in dma_sync_phys()
  MIPS: eBPF: Remove REG_32BIT_ZERO_EX
  MIPS: eBPF: Always return sign extended 32b values
  MIPS: CM: Fix indentation
  MIPS: BCM47XX: Fix/improve Buffalo WHR-G54S support
  MIPS: OCTEON: program rx/tx-delay always from DT
  MIPS: OCTEON: delete board-specific link status
  MIPS: OCTEON: don't lie about interface type of CN3005 board
  MIPS: OCTEON: warn if deprecated link status is being used
  MIPS: OCTEON: add fixed-link nodes to in-kernel device tree
  MIPS: Delete unused flush_cache_sigtramp()
  ...

Merge branch 'parisc-5.1-1' of git://git./linux/kernel/git/deller/parisc-linux

Pull parisc updates from Helge Deller:
"The most important changes in this patch set are:

   - DMA-related cleanups for parisc with the aim to move anything not
     required by drivers out of <asm/dma-mapping.h>, by Christoph
     Hellwig

   - Switch to memblock_alloc(), by Mike Rapoport

   - Makefile cleanups by Masahiro Yamada

   - Switch to bust_spinlocks(), by Sergey Senozhatsky

   - Improved initial SMP affinity selection for IRQs

   - Added IPI- and rescheduling interrupts in /proc/interrupts output"

* 'parisc-5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux: (21 commits)
  parisc: use memblock_alloc() instead of custom get_memblock()
  parisc: Add constants for various PDC firmware calls
  parisc: Add constant for PDC_PAT_COMPLEX firmware call
  parisc: Show machine product number during boot
  parisc: Add constants for PDC_RELOCATE PDC call
  parisc: Add PDC_CRASH_PREP PDC function number
  parisc: Use F_EXTEND() macro in iosapic code
  parisc: remove the HBA_DATA macro
  parisc/lba_pci: use container_of in LBA_DEV
  parisc/dino: use container_of in DINO_DEV
  parisc: properly type the return value of parisc_walk_tree
  parisc: properly type the iommu field in struct pci_hba_data
  parisc: turn GET_IOC into an inline function
  parisc: move internal implementation details out of <asm/dma-mapping.h>
  parisc: don't include <asm/cacheflush.h> in <asm/dma-mapping.h>
  parisc: remove meaningless ccflags-y in arch/parisc/boot/Makefile
  parisc: replace oops_in_progress manipulation with bust_spinlocks()
  parisc: Improve initial IRQ to CPU assignment
  parisc: Count IPI function call interrupts
  parisc: Show rescheduling interrupts on SMP machines only
  ...

Merge tag 's390-5.1-1' of git://git./linux/kernel/git/s390/linux

Pull s390 updates from Martin Schwidefsky:

- A copy of Arnds compat wrapper generation series

- Pass information about the KVM guest to the host in form the control
   program code and the control program version code

- Map IOV resources to support PCI physical functions on s390

- Add vector load and store alignment hints to improve performance

- Use the "jdd" constraint with gcc 9 to make jump labels working again

- Remove amode workaround for old z/VM releases from the DCSS code

- Add support for in-kernel performance measurements using the CPU
   measurement counter facility

- Introduce a new PMU device cpum_cf_diag to capture counters and store
   thenn as event raw data.

- Bug fixes and cleanups

* tag 's390-5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (54 commits)
  Revert "s390/cpum_cf: Add kernel message exaplanations"
  s390/dasd: fix read device characteristic with CONFIG_VMAP_STACK=y
  s390/suspend: fix prefix register reset in swsusp_arch_resume
  s390: warn about clearing als implied facilities
  s390: allow overriding facilities via command line
  s390: clean up redundant facilities list setup
  s390/als: remove duplicated in-place implementation of stfle
  s390/cio: Use cpa range elsewhere within vfio-ccw
  s390/cio: Fix vfio-ccw handling of recursive TICs
  s390: vfio_ap: link the vfio_ap devices to the vfio_ap bus subsystem
  s390/cpum_cf: Handle EBUSY return code from CPU counter facility reservation
  s390/cpum_cf: Add kernel message exaplanations
  s390/cpum_cf_diag: Add support for s390 counter facility diagnostic trace
  s390/cpum_cf: add ctr_stcctm() function
  s390/cpum_cf: move common functions into a separate file
  s390/cpum_cf: introduce kernel_cpumcf_avail() function
  s390/cpu_mf: replace stcctm5() with the stcctm() function
  s390/cpu_mf: add store cpu counter multiple instruction support
  s390/cpum_cf: Add minimal in-kernel interface for counter measurements
  s390/cpum_cf: introduce kernel_cpumcf_alert() to obtain measurement alerts
  ...

Merge tag 'm68k-for-v5.1-tag1' of git://git./linux/kernel/git/geert/linux-m68k

Pull m68k updates from Geert Uytterhoeven:

- VLA removal

- gcc-8.x build fixes

- small improvements and cleanups

- defconfig updates

* tag 'm68k-for-v5.1-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k: Add -ffreestanding to CFLAGS
  m68k/apollo: Fix comment in Makefile
  dio: Fix buffer overflow in case of unknown board
  m68k/defconfig: Update defconfigs for v5.0-rc1
  m68k/atari: Avoid VLA use in atari_switches_setup()
  m68k: Avoid VLA use in mangle_kernel_stack()
  m68k/mac: Use '030 reset method on SE/30
  m68k/mac: Remove obsolete comment
  m68k/mac: Skip VIA port setup unless RTC is connected
  m68k/mac: Clean up unused timer definitions
  m68k/defconfig: Drop NET_VENDOR_<FOO>=n

x86: Deprecate a.out support

Linux supports ELF binaries for ~25 years now. a.out coredumping has
bitrotten quite significantly and would need some fixing to get it into
shape again but considering how even the toolchains cannot create a.out
executables in its default configuration, let's deprecate a.out support
and remove it a couple of releases later, instead.

Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Richard Weinberger <richard@nod.at>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Jann Horn <jannh@google.com>
Cc: <linux-api@vger.kernel.org>
Cc: <linux-fsdevel@vger.kernel.org>
Cc: lkml <linux-kernel@vger.kernel.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: <x86@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

a.out: remove core dumping support

We're (finally) phasing out a.out support for good.  As Borislav Petkov
points out, we've supported ELF binaries for about 25 years by now, and
coredumping in particular has bitrotted over the years.

None of the tool chains even support generating a.out binaries any more,
and the plan is to deprecate a.out support entirely for the kernel.  But
I want to start with just removing the core dumping code, because I can
still imagine that somebody actually might want to support a.out as a
simpler biinary format.

Particularly if you generate some random binaries on the fly, ELF is a
much more complicated format (admittedly ELF also does have a lot of
toolchain support, mitigating that complexity a lot and you really
should have moved over in the last 25 years).

So it's at least somewhat possible that somebody out there has some
workflow that still involves generating and running a.out executables.

In contrast, it's very unlikely that anybody depends on debugging any
legacy a.out core files.  But regardless, I want this phase-out to be
done in two steps, so that we can resurrect a.out support (if needed)
without having to resurrect the core file dumping that is almost
certainly not needed.

Jann Horn pointed to the <asm/a.out-core.h> file that my first trivial
cut at this had missed.

And Alan Cox points out that the a.out binary loader _could_ be done in
user space if somebody wants to, but we might keep just the loader in
the kernel if somebody really wants it, since the loader isn't that big
and has no really odd special cases like the core dumping does.

Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Cc: Jann Horn <jannh@google.com>
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'linus' of git://git./linux/kernel/git/herbert/crypto-2.6

Pull crypto update from Herbert Xu:
"API:
   - Add helper for simple skcipher modes.
   - Add helper to register multiple templates.
   - Set CRYPTO_TFM_NEED_KEY when setkey fails.
   - Require neither or both of export/import in shash.
   - AEAD decryption test vectors are now generated from encryption
     ones.
   - New option CONFIG_CRYPTO_MANAGER_EXTRA_TESTS that includes random
     fuzzing.

  Algorithms:
   - Conversions to skcipher and helper for many templates.
   - Add more test vectors for nhpoly1305 and adiantum.

  Drivers:
   - Add crypto4xx prng support.
   - Add xcbc/cmac/ecb support in caam.
   - Add AES support for Exynos5433 in s5p.
   - Remove sha384/sha512 from artpec7 as hardware cannot do partial
     hash"

[ There is a merge of the Freescale SoC tree in order to pull in changes
  required by patches to the caam/qi2 driver. ]

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (174 commits)
  crypto: s5p - add AES support for Exynos5433
  dt-bindings: crypto: document Exynos5433 SlimSSS
  crypto: crypto4xx - add missing of_node_put after of_device_is_available
  crypto: cavium/zip - fix collision with generic cra_driver_name
  crypto: af_alg - use struct_size() in sock_kfree_s()
  crypto: caam - remove redundant likely/unlikely annotation
  crypto: s5p - update iv after AES-CBC op end
  crypto: x86/poly1305 - Clear key material from stack in SSE2 variant
  crypto: caam - generate hash keys in-place
  crypto: caam - fix DMA mapping xcbc key twice
  crypto: caam - fix hash context DMA unmap size
  hwrng: bcm2835 - fix probe as platform device
  crypto: s5p-sss - Use AES_BLOCK_SIZE define instead of number
  crypto: stm32 - drop pointless static qualifier in stm32_hash_remove()
  crypto: chelsio - Fixed Traffic Stall
  crypto: marvell - Remove set but not used variable 'ivsize'
  crypto: ccp - Update driver messages to remove some confusion
  crypto: adiantum - add 1536 and 4096-byte test vectors
  crypto: nhpoly1305 - add a test vector with len % 16 != 0
  crypto: arm/aes-ce - update IV after partial final CTR block
  ...

Merge git://git./linux/kernel/git/davem/net-next

Pull networking updates from David Miller:
"Here we go, another merge window full of networking and #ebpf changes:

   1) Snoop DHCPACKS in batman-adv to learn MAC/IP pairs in the DHCP
      range without dealing with floods of ARP traffic, from Linus
      Lüssing.

   2) Throttle buffered multicast packet transmission in mt76, from
      Felix Fietkau.

   3) Support adaptive interrupt moderation in ice, from Brett Creeley.

   4) A lot of struct_size conversions, from Gustavo A. R. Silva.

   5) Add peek/push/pop commands to bpftool, as well as bash completion,
      from Stanislav Fomichev.

   6) Optimize sk_msg_clone(), from Vakul Garg.

   7) Add SO_BINDTOIFINDEX, from David Herrmann.

   8) Be more conservative with local resends due to local congestion,
      from Yuchung Cheng.

   9) Allow vetoing of unsupported VXLAN FDBs, from Petr Machata.

  10) Add health buffer support to devlink, from Eran Ben Elisha.

  11) Add TXQ scheduling API to mac80211, from Toke Høiland-Jørgensen.

  12) Add statistics to basic packet scheduler filter, from Cong Wang.

  13) Add GRE tunnel support for mlxsw Spectrum-2, from Nir Dotan.

  14) Lots of new IP tunneling forwarding tests, also from Nir Dotan.

  15) Add 3ad stats to bonding, from Nikolay Aleksandrov.

  16) Lots of probing improvements for bpftool, from Quentin Monnet.

  17) Various nfp drive #ebpf JIT improvements from Jakub Kicinski.

  18) Allow #ebpf programs to access gso_segs from skb shared info, from
      Eric Dumazet.

  19) Add sock_diag support for AF_XDP sockets, from Björn Töpel.

  20) Support 22260 iwlwifi devices, from Luca Coelho.

  21) Use rbtree for ipv6 defragmentation, from Peter Oskolkov.

  22) Add JMP32 instruction class support to #ebpf, from Jiong Wang.

  23) Add spinlock support to #ebpf, from Alexei Starovoitov.

  24) Support 256-bit keys and TLS 1.3 in ktls, from Dave Watson.

  25) Add device infomation API to devlink, from Jakub Kicinski.

  26) Add new timestamping socket options which are y2038 safe, from
      Deepa Dinamani.

  27) Add RX checksum offloading for various sh_eth chips, from Sergei
      Shtylyov.

  28) Flow offload infrastructure, from Pablo Neira Ayuso.

  29) Numerous cleanups, improvements, and bug fixes to the PHY layer
      and many drivers from Heiner Kallweit.

  30) Lots of changes to try and make packet scheduler classifiers run
      lockless as much as possible, from Vlad Buslov.

  31) Support BCM957504 chip in bnxt_en driver, from Erik Burrows.

  32) Add concurrency tests to tc-tests infrastructure, from Vlad
      Buslov.

  33) Add hwmon support to aquantia, from Heiner Kallweit.

  34) Allow 64-bit values for SO_MAX_PACING_RATE, from Eric Dumazet.

  And I would be remiss if I didn't thank the various major networking
  subsystem maintainers for integrating much of this work before I even
  saw it. Alexei Starovoitov, Daniel Borkmann, Pablo Neira Ayuso,
  Johannes Berg, Kalle Valo, and many others. Thank you!"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2207 commits)
  net/sched: avoid unused-label warning
  net: ignore sysctl_devconf_inherit_init_net without SYSCTL
  phy: mdio-mux: fix Kconfig dependencies
  net: phy: use phy_modify_mmd_changed in genphy_c45_an_config_aneg
  net: dsa: mv88e6xxx: add call to mv88e6xxx_ports_cmode_init to probe for new DSA framework
  selftest/net: Remove duplicate header
  sky2: Disable MSI on Dell Inspiron 1545 and Gateway P-79
  net/mlx5e: Update tx reporter status in case channels were successfully opened
  devlink: Add support for direct reporter health state update
  devlink: Update reporter state to error even if recover aborted
  sctp: call iov_iter_revert() after sending ABORT
  team: Free BPF filter when unregistering netdev
  ip6mr: Do not call __IP6_INC_STATS() from preemptible context
  isdn: mISDN: Fix potential NULL pointer dereference of kzalloc
  net: dsa: mv88e6xxx: support in-band signalling on SGMII ports with external PHYs
  cxgb4/chtls: Prefix adapter flags with CXGB4
  net-sysfs: Switch to bitmap_zalloc()
  mellanox: Switch to bitmap_zalloc()
  bpf: add test cases for non-pointer sanitiation logic
  mlxsw: i2c: Extend initialization by querying resources data
  ...

Revert "s390/cpum_cf: Add kernel message exaplanations"

This reverts commit fb3a0b61e0d4e435016cc91575d051f841791da0.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Merge tag 'leds-for-5.1-rc1' of git://git./linux/kernel/git/j.anaszewski/linux-leds

Pull LED updates from Jacek Anaszewski:

- finalize previously announced support for initialization of pattern
   triggers from Device Tree

- fix for null deref on firmware load failure in leds-lp55xx-common.c

* tag 'leds-for-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
  leds: lp55xx: fix null deref on firmware load failure
  leds: trigger: timer: Add initialization from Device Tree
  leds: trigger: oneshot: Add initialization from Device Tree
  leds: trigger: pattern: Add pattern initialization from Device Tree
  leds: Add helper for getting default pattern from Device Tree
  dt-bindings: leds: Add pattern initialization from Device Tree

Merge tag 'hwmon-for-v5.1' of git://git./linux/kernel/git/groeck/linux-staging

Pull hwmon updates from Guenter Roeck:

- Add support for LM96000, DPS-650AB to existing drivers

- Use permission specific SENSOR[_DEVICE]_ATTR variants in several
   drivers

- Replace S_<PERMS> with octal values in several drivers

- Update some license headers

- Various minor fixes and improvements in several drivers

* tag 'hwmon-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (89 commits)
  dt-bindings: hwmon: Add missing documentation for lm75
  hwmon: (ad7418) Add device tree probing
  hwmon: (ad741x) Add DT bindings for Analog Devices AD741x
  hwmon: (ntc_thermistor) Convert to new hwmon API
  hwmon: (pwm-fan) Add optional regulator support
  dt-bindings: hwmon: Add optional regulator support to pwm-fan
  hwmon: (f71882fg) Mark expected switch fall-through
  hwmon: (ad7418) Catch I2C errors
  hwmon: (lm85) add support for LM96000 high frequencies
  hwmon: (lm85) support the LM96000
  dt-bindings: Add LM96000 as a trivial device
  hwmon: (lm85) remove freq_map size hardcodes
  hwmon: (occ) Fix license headers
  hwmon: (via-cputemp) Use permission specific SENSOR[_DEVICE]_ATTR variants
  hwmon: (vexpress-hwmon) Use permission specific SENSOR[_DEVICE]_ATTR variants
  hwmon: (tmp421) Replace S_<PERMS> with octal values
  hwmon: (tmp103) Use permission specific SENSOR[_DEVICE]_ATTR variants
  hwmon: (tmp102) Replace S_<PERMS> with octal values
  hwmon: (tc74) Use permission specific SENSOR[_DEVICE]_ATTR variants
  hwmon: (tc654) Use permission specific SENSOR[_DEVICE]_ATTR variants
  ...

Merge tag 'spi-v5.1' of git://git./linux/kernel/git/broonie/spi

Pull spi updates from Mark Brown:
"A fairly quiet release for SPI, the biggest thing is the conversion to
  use GPIO descriptors which is now 90% done but still needs some
  stragglers converting.

  Summary:

   - Support for inter-word delays

   - Conversion of the core and most drivers to use GPIO descriptors for
     GPIO controlled chip selects

   - New drivers for NXP FlexSPI and QuadSPI, SiFive and Spreadtrum"

* tag 'spi-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (104 commits)
  spi: sh-msiof: Restrict bits per word to 8/16/24/32 on R-Car Gen2/3
  spi: sifive: Remove redundant dev_err call in sifive_spi_probe()
  spi: sifive: Remove spi_master_put in sifive_spi_remove()
  spi: spi-gpio: fix SPI_CS_HIGH capability
  spi: pxa2xx: Setup maximum supported DMA transfer length
  spi: sifive: Add driver for the SiFive SPI controller
  spi: sifive: Add DT documentation for SiFive SPI controller
  spi: sprd: Add a prefix for SPI DMA channel macros
  spi: sprd: spi: sprd: Add DMA mode support
  dt-bindings: spi: Add the DMA properties for the SPI dma mode
  spi: sprd: Add the SPI irq function for the SPI DMA mode
  dt-bindings: spi: imx: Add an entry for the i.MX8QM compatible
  spi: use gpio[d]_set_value_cansleep for setting chipselect GPIO
  spi: gpio: Advertise support for SPI_CS_HIGH
  spi: sh-msiof: Replace spi_master by spi_controller
  spi: sh-hspi: Replace spi_master by spi_controller
  spi: rspi: Replace spi_master by spi_controller
  spi: atmel-quadspi: add support for sam9x60 qspi controller
  dt-bindings: spi: atmel-quadspi: QuadSPI driver for Microchip SAM9X60
  spi: atmel-quadspi: add support for named peripheral clock
  ...

Merge tag 'regulator-v5.1' of git://git./linux/kernel/git/broonie/regulator

Pull regulator updates from Mark Brown:
"The bulk of the standout changes in this release are cleanups, with
  the core work being a combination of factoring out common code into
  helpers and the completion of the conversion of the core to use GPIO
  descriptors.

  Summary:

   - Addition of helper functions for current limits and conversion of
     drivers to use them by Axel Lin.

   - Lots and lots of cleanups from Axel Lin.

   - Conversion of the core to use GPIO descriptors rather than numbers
     by Linus Walleij.

   - New drivers for Maxim MAX77650 and ROHM BD70528"

* tag 'regulator-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (131 commits)
  regulator: mc13xxx: Constify regulator_ops variables
  regulator: palmas: Constify palmas_smps_ramp_delay array
  regulator: wm831x-dcdc: Convert to use regulator_set/get_current_limit_regmap
  regulator: pv88090: Convert to use regulator_set/get_current_limit_regmap
  regulator: pv88080: Convert to use regulator_set/get_current_limit_regmap
  regulator: pv88060: Convert to use regulator_set/get_current_limit_regmap
  regulator: max77650: Convert to use regulator_set/get_current_limit_regmap
  regulator: lp873x: Convert to use regulator_set/get_current_limit_regmap
  regulator: lp872x: Convert to use regulator_set/get_current_limit_regmap
  regulator: da9210: Convert to use regulator_set/get_current_limit_regmap
  regulator: da9055: Convert to use regulator_set/get_current_limit_regmap
  regulator: core: Add set/get_current_limit helpers for regmap users
  regulator: Fix comment for csel_reg and csel_mask
  regulator: stm32-vrefbuf: add power management support
  regulator: 88pm8607: Remove unused fields from struct pm8607_regulator_info
  regulator: 88pm8607: Simplify pm8607_list_voltage implementation
  regulator: cpcap: Constify omap4_regulators and xoom_regulators
  regulator: cpcap: Remove unused vsel_shift from struct cpcap_regulator
  dt-bindings: regulator: tps65218: rectify units of LS3
  dt-bindings: regulator: add LS2 load switch documentation
  ...

Merge tag 'regmap-v5.1' of git://git./linux/kernel/git/broonie/regmap

Pull regmap updates from Mark Brown:
"There are only two changes here:

   - fix for conflicting attributes on the rbtree node structure

   - implementation of main status register support in the interrupt
     code which supports chips that have a register to cut down on the
     number of per-interrupt status registers that need to be checked
     when handling interrupts"

* tag 'regmap-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: Remove attribute packed from struct 'regcache_rbtree_node'
  regmap: regmap-irq: Add main status register support

Merge tag 'mmc-v5.1' of git://git./linux/kernel/git/ulfh/mmc

Pull MMC updates from Ulf Hansson:
"MMC core:
   - Fixup max_discard/trim calculations
   - Announce SD specs greater than 4.0
   - Add discard support for SD cards
   - Don't do retries for CMD6 (SWITCH command)
   - Various cleanups and re-structuring

  MMC host:
   - cqhci:
      * Add maintainers for eMMC CQHCI driver
   - sdhci:
      * Consolidate WP GPIO code
      * Add ADMA3 DMA support for V4 enabled host
      * Fixup card detect support in pci-o2micro driver
      * Add support for CMDQ and SDMMC pads auto-calibration in tegra
        driver
      * Add DCMD support and CMDQ support, support for i.MX6ULL variant,
        fixup HS400 timing issue and add HS400_ES support for i.MX8QXP
        to esdhc-imx driver
      * Avoid CRC errors by adjusting settings to speed mode and fixup
        card initialization for high speed mode in renesas_sdhi
      * Fixup timeout settings for omap
      * Enable 8 bits bus-width support in atmel-mci
      * Convert some legacy code in jz4740 driver to use modern APIs
      * Send a CMD12 to clear DPSM at errors for STM32 sdmmc mmci
        driver"

* tag 'mmc-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (69 commits)
  mmc:fix a bug when max_discard is 0
  mmc: core: Add a debug print when the card may have been replaced
  mmc: core: Add sd discard timeout
  mmc: core: Add discard support to sd
  mmc: sdhci-esdhc-imx: clear the HALT bit when enable CQE
  mmc: core: do not retry CMD6 in __mmc_switch()
  mmc: core: Convert mmc_align_data_size() into an SDIO specific function
  mmc: core: Move mmc_of_parse_voltage() to host.c
  mmc: core: Convert mmc_regulator_get_ocrmask() to static
  mmc: core: Move regulator helpers to separate file
  mmc: of_mmc_spi: Convert to mmc_of_parse_voltage()
  mmc: core: Drop retries as in-parameter to mmc_wait_for_app_cmd()
  mmc: core: Convert mmc_wait_for_app_cmd() to static
  mmc: renesas_sdhi: Change HW adjustment register according to speed mode
  mmc: mmci: Send a CMD12 to clear the DPSM at errors
  mmc: sdhci-xenon: Fixup already marked switch fall-through
  mmc: sdhci-tegra: drop ->get_ro() implementation
  mmc: sdhci-omap: drop ->get_ro() implementation
  mmc: sdhci: use WP GPIO in sdhci_check_ro()
  mmc: wmt-sdmmc: Drop unused include
  ...

Merge tag 'i3c/for-5.1' of git://git./linux/kernel/git/i3c/linux

Pull i3c updates from Boris Brezillon:

- Add a /* fall-through */ comment in the dw-i3c-master driver

- Update the I3C entries in MAINTAINERS to add an IRC chan

* tag 'i3c/for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: master: dw-i3c-master: mark expected switch fall-through
MAINTAINERS: Add an IRC channel for the I3C subsystem

Merge tag 'mtd/for-5.1' of git://git.infradead.org/linux-mtd

Pull MTD updates from Boris Brezillon:
"Core MTD changes:
   - Use struct_size() where appropriate
   - mtd_{read,write}() as wrappers around mtd_{read,write}_oob()
   - Fix misuse of PTR_ERR() in docg3
   - Coding style improvements in mtdcore.c

  SPI NOR changes:
    Core changes:
     - Add support of octal mode I/O transfer
     - Add a bunch of SPI NOR entries to the flash_info table

    SPI NOR controller driver changes:
     - cadence-quadspi:
        * Add support for Octal SPI controller
        * write upto 8-bytes data in STIG mode
     - mtk-quadspi:
        * rename config to a common one
        * add SNOR_HWCAPS_READ to spi_nor_hwcaps mask
     - Add Tudor as SPI-NOR co-maintainer

  NAND changes:
    NAND core changes:
     - Fourth batch of fixes/cleanup to the raw NAND core impacting
       various controller drivers (Sunxi, Marvell, MTK, TMIO, OMAP2).
     - Check the return code of nand_reset() and nand_readid_op().
     - Remove ->legacy.erase and single_erase().
     - Simplify the locking.
     - Several implicit fall through annotations.

    Raw NAND controllers drivers changes:
     - Fix various possible object reference leaks (MTK, JZ4780, Atmel)
     - ST:
        * Add support for STM32 FMC2 NAND flash controller
     - Meson:
        * Add support for Amlogic NAND flash controller
     - Denali:
        * Several cleanup patches
     - Sunxi:
        * Several cleanup patches
     - FSMC:
        * Disable NAND on remove()
        * Reset NAND timings on resume()

    SPI-NAND drivers changes:
     - Toshiba:
        * Add support for all Toshiba products.
     - Macronix:
        * Fix ECC status read.
     - Gigadevice:
        * Add support for GD5F1GQ4UExxG"

* tag 'mtd/for-5.1' of git://git.infradead.org/linux-mtd: (64 commits)
  mtd: spi-nor: Fix wrong abbreviation HWCPAS
  mtd: spi-nor: cadence-quadspi: fix spelling mistake: "Couldnt't" -> "Couldn't"
  mtd: spi-nor: Add support for en25qh64
  mtd: spi-nor: Add support for MX25V8035F
  mtd: spi-nor: Add support for EN25Q80A
  mtd: spi-nor: cadence-quadspi: Add support for Octal SPI controller
  dt-bindings: cadence-quadspi: Add new compatible for AM654 SoC
  mtd: spi-nor: split s25fl128s into s25fl128s0 and s25fl128s1
  mtd: spi-nor: cadence-quadspi: write upto 8-bytes data in STIG mode
  mtd: spi-nor: Add support for mx25u3235f
  mtd: rawnand: denali_dt: remove single anonymous clock support
  mtd: rawnand: mtk: fix possible object reference leak
  mtd: rawnand: jz4780: fix possible object reference leak
  mtd: rawnand: atmel: fix possible object reference leak
  mtd: rawnand: fsmc: Disable NAND on remove()
  mtd: rawnand: fsmc: Reset NAND timings on resume()
  mtd: spinand: Add support for GigaDevice GD5F1GQ4UExxG
  mtd: rawnand: denali: remove unused dma_addr field from denali_nand_info
  mtd: rawnand: denali: remove unused function argument 'raw'
  mtd: rawnand: denali: remove unneeded denali_reset_irq() call
  ...

Merge tag 'vfio-v5.1-rc1' of git://github.com/awilliam/linux-vfio

Pull VFIO updates from Alex Williamson:

- Switch mdev to generic UUID API (Andy Shevchenko)

- Fixup platform reset include paths (Masahiro Yamada)

- Fix usage of MINORMASK (Chengguang Xu)

- Remove noise from duplicate spapr table unsets (Alexey Kardashevskiy)

- Restore device state after PM reset (Alex Williamson)

- Ensure memory translation enabled for PCI ROM access (Eric Auger)

* tag 'vfio-v5.1-rc1' of git://github.com/awilliam/linux-vfio:
  vfio_pci: Enable memory accesses before calling pci_map_rom
  vfio/pci: Restore device state on PM transition
  vfio/spapr_tce: Skip unsetting already unset table
  samples/vfio-mdev/mtty: expand minor range when registering chrdev region
  samples/vfio-mdev/mdpy: expand minor range when registering chrdev region
  samples/vfio-mdev/mbochs: expand minor range when registering chrdev region
  vfio: expand minor range when registering chrdev region
  vfio: platform: reset: fix up include directives to remove ccflags-y
  vfio-mdev: Switch to use new generic UUID API

fs: Make splice() and tee() take into account O_NONBLOCK flag on pipes

The current implementation of splice() and tee() ignores O_NONBLOCK set
on pipe file descriptors and checks only the SPLICE_F_NONBLOCK flag for
blocking on pipe arguments.  This is inconsistent since splice()-ing
from/to non-pipe file descriptors does take O_NONBLOCK into
consideration.

Fix this by promoting O_NONBLOCK, when set on a pipe, to
SPLICE_F_NONBLOCK.

Some context for how the current implementation of splice() leads to
inconsistent behavior.  In the ongoing work[1] to add VM tracing
capability to trace-cmd we stream tracing data over named FIFOs or
vsockets from guests back to the host.

When we receive SIGINT from user to stop tracing, we set O_NONBLOCK on
the input file descriptor and set SPLICE_F_NONBLOCK for the next call to
splice().  If splice() was blocked waiting on data from the input FIFO,
after SIGINT splice() restarts with the same arguments (no
SPLICE_F_NONBLOCK) and blocks again instead of returning -EAGAIN when no
data is available.

This differs from the splice() behavior when reading from a vsocket or
when we're doing a traditional read()/write() loop (trace-cmd's
--nosplice argument).

With this patch applied we get the same behavior in all situations after
setting O_NONBLOCK which also matches the behavior of doing a
read()/write() loop instead of splice().

This change does have potential of breaking users who don't expect
EAGAIN from splice() when SPLICE_F_NONBLOCK is not set.  OTOH programs
that set O_NONBLOCK and don't anticipate EAGAIN are arguably buggy[2].

[1] https://github.com/skaslev/trace-cmd/tree/vsock
[2] https://github.com/torvalds/linux/blob/d47e3da1759230e394096fd742aad423c291ba48/fs/read_write.c#L1425

Signed-off-by: Slavomir Kaslev <kaslevs@vmware.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge git://git./linux/kernel/git/davem/net

Merge branch 'fixes' of git://git./linux/kernel/git/viro/vfs

Pull vfs fixes from Al Viro:
"Assorted fixes that sat in -next for a while, all over the place"

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  aio: Fix locking in aio_poll()
  exec: Fix mem leak in kernel_read_file
  copy_mount_string: Limit string length to PATH_MAX
  cgroup: saner refcounting for cgroup_root
  fix cgroup_do_mount() handling of failure exits

net/sched: avoid unused-label warning

The label is only used from inside the #ifdef and should be
hidden the same way, to avoid this warning:

net/sched/act_tunnel_key.c: In function 'tunnel_key_init':
net/sched/act_tunnel_key.c:389:1: error: label 'release_tun_meta' defined but not used [-Werror=unused-label]
release_tun_meta:

Fixes: 41411e2fd6b8 ("net/sched: act_tunnel_key: Add dst_cache support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ignore sysctl_devconf_inherit_init_net without SYSCTL

When CONFIG_SYSCTL is turned off, we get a link failure for
the newly introduced tuning knob.

net/ipv6/addrconf.o: In function `addrconf_init_net':
addrconf.c:(.text+0x31dc): undefined reference to `sysctl_devconf_inherit_init_net'

Add an IS_ENABLED() check to fall back to the default behavior
(sysctl_devconf_inherit_init_net=0) here.

Fixes: 856c395cfa63 ("net: introduce a knob to control whether to inherit devconf config")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christian Brauner <christian@brauner.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

phy: mdio-mux: fix Kconfig dependencies

MDIO_BUS_MUX can only be selected if OF_MDIO is already turned on:

WARNING: unmet direct dependencies detected for MDIO_BUS_MUX
  Depends on [n]: NETDEVICES [=y] && MDIO_BUS [=m] && OF_MDIO [=n]
  Selected by [m]:
  - MDIO_BUS_MUX_MULTIPLEXER [=m] && NETDEVICES [=y] && MDIO_BUS [=m] && OF [=y]

Fixes: 7865ad6551c9 ("drivers: net: phy: mdio-mux: Add support for Generic Mux controls")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: use phy_modify_mmd_changed in genphy_c45_an_config_aneg

As can be seen from the usage of the return value, we should use
phy_modify_mmd_changed() here.

Fixes: 9a5dc8af4416 ("net: phy: add genphy_c45_an_config_aneg")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: mv88e6xxx: add call to mv88e6xxx_ports_cmode_init to probe for new DSA framework

In the original patch I missed to add mv88e6xxx_ports_cmode_init()
to the second probe function, the one for the new DSA framework.

Fixes: ed8fe20205ac ("net: dsa: mv88e6xxx: prevent interrupt storm caused by mv88e6390x_port_set_cmode")
Reported-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>