Andrew Cameron [Thu, 7 Nov 2019 02:12:55 +0000 (20:12 -0600)]
ath79: add support for the TP-LINK WBS510 V2
This adds support for a popular low-cost 5GHz N based AP
Specifications:
- SoC: Atheros AR9344
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 5GHz 300 Mbps, 2x RP-SMA connector, 27 dBm TX power
- Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
Hauke Mehrtens [Sun, 17 Nov 2019 22:59:37 +0000 (23:59 +0100)]
wireless-regdb: Make it build with python2
This backports a patch to build it work with python2 in addition to
python3.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Petr Štetiar <ynezz@true.cz>
Lech Perczak [Sun, 17 Nov 2019 19:58:27 +0000 (20:58 +0100)]
ar71xx: ubnt-(xm,xw): add rssileds package
In order to make RSSI indicator on the device work out of box,
include "rssileds" package in per-device rootfs image by default
for Ubiquiti XM and XW devices, namely:
- Bullet M (XM/XW)
- Rocket M (XM/XW)
- Nanostation M (XM/XW)
- Nanostation Loco-M (XW)
This moves the package addition to the individual devices in order
to prevent accidental inclusions of the package when not looking
at the parent node carefully enough.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[add bullet-m-xw, remove rocket-m-ti, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Mon, 18 Nov 2019 22:59:06 +0000 (23:59 +0100)]
ath79: add PoE passthrough switch for Ubiquiti Nanostation (XM/XW)
This adds the gpio switch to enable PoE passthrough on Ubiquiti
Nanostation (XM/XW).
Values are copied from the implementation in ar71xx.
GPIO values checked on:
- NanoStation M5 XW
- NanoStation M2 XM
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Vladimir Vid [Mon, 9 Sep 2019 16:50:26 +0000 (18:50 +0200)]
uboot-mvebu: add uDPU board
* add u-boot support for uDPU
* add line to copy u-boot binary to STAGING_DIR_IMAGE, this can later be used
as BL33 variable required for ATF build
* add patch to increase max gunzip size in mvebu_armada-37xx.h which is
required for booting the itb recovery images
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Vladimir Vid [Fri, 25 Oct 2019 15:24:38 +0000 (17:24 +0200)]
packages/boot: add arm-trusted-firmware-mvebu and initial uDPU support
ATF mvebu is required for building a functional bootloader for A7K/A8K and
A37xx platforms. uDPU device is added as the first target.
A3700 platform has a wide range of settings which can be used per device, so
options are defined under the Device sections.
Platform also required WTP (recovery) tools and mv-ddr package for the DDR
topology configuration. 32-bit cross compiler is used for building the WTMI
image.
After the build, flash-image.bin can be used with the bubt command from the
u-boot shell to flash the new version of u-boot.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Kevin Darbyshire-Bryant [Tue, 19 Nov 2019 15:12:42 +0000 (15:12 +0000)]
netifd: dhcp proto convert release to norelease
Change dhcp no/release on shutdown to 'norelease' uci option to match
existing proto dhcpv6 usage.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Acked-by: Hans Dedecker <dedeckeh@gmail.com>
Andre Heider [Thu, 3 Oct 2019 16:11:17 +0000 (18:11 +0200)]
am33x-cm3: remove
This is currently unused and not working anyway, since the used upstream
kernel loads am335x-pm-firmware.elf and not am335x-pm-firmware.bin [0].
The last downstream patches using the latter were removed with
e4eef7e6.
Remove it instead of fixing it since the rtc-only sleep state can even
damage the hardware [1].
[0] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=
ccbbb9faac946ce61c241ce9f08b3486fabf031d
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=
7a6cb0abe1aa63334f3ded6d2b6c8eca80e72302
Signed-off-by: Andre Heider <a.heider@gmail.com>
Andre Heider [Sat, 7 Sep 2019 10:36:52 +0000 (12:36 +0200)]
omap: support booting off different mmc devices
Tested with installing to/sysupgrading from sd and emmc on boneblack.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Andre Heider [Fri, 6 Sep 2019 20:53:23 +0000 (22:53 +0200)]
omap: switch from uEnv.txt to generic distro booting
Which makes supporting different boot devices easy.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Andre Heider [Fri, 6 Sep 2019 09:25:30 +0000 (11:25 +0200)]
omap: update uboot to 2019.10
All patches have been dropped, they're either redundant (e.g. due to the
new and unset CONFIG_SPL_FAT_WRITE), break compilation (thumb hacks) or
have been applied upstream.
The defconfig for am335x_boneblack has been removed upstream [0], so use
am335x_evm for boneblack too.
Size changes (before, after, file):
ti_am335x-evm and ti_am335x-bone-black:
79804 110832 MLO
623836 756148 u-boot.img
ti_omap3-beagle:
54148 57708 MLO
496272 665728 u-boot.img
ti_omap4-panda:
39356 40204 MLO
284648 366672 u-boot.img
Tested on boneblack, which has the biggest spl size increase. The beagle and
panda spl sizes seem reasonable to not break booting.
[0] https://gitlab.denx.de/u-boot/u-boot/commit/
8fa7f65dd02c176ee6021eaf40114560b8954ba2
Signed-off-by: Andre Heider <a.heider@gmail.com>
Andre Heider [Fri, 6 Sep 2019 07:48:22 +0000 (09:48 +0200)]
omap: switch to kernel 4.19
Signed-off-by: Andre Heider <a.heider@gmail.com>
Andre Heider [Fri, 6 Sep 2019 10:00:17 +0000 (12:00 +0200)]
omap: enable new sound kernel options
This gets rid of a boot time warning about the missing edma module.
Enable SND_OMAP_SOC_HDMI_AUDIO while here.
All enabled options default to y.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Andre Heider [Sun, 13 Oct 2019 03:56:46 +0000 (05:56 +0200)]
omap: disable excess kernel debug options
Signed-off-by: Andre Heider <a.heider@gmail.com>
Andre Heider [Fri, 6 Sep 2019 07:48:00 +0000 (09:48 +0200)]
omap: run `make oldconfig` for kernel 4.19
The only manually enabled config is the new OMAP4_DSS_HDMI_CEC, which
defaults to y.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Andre Heider [Fri, 6 Sep 2019 07:22:29 +0000 (09:22 +0200)]
omap: copy the kernel 4.14 config for 4.19
Signed-off-by: Andre Heider <a.heider@gmail.com>
Koen Vandeputte [Wed, 20 Nov 2019 07:50:24 +0000 (08:50 +0100)]
ipq40xx: fix build error
Add missing brace which was accidentally omitted
Fixes: d6aea46a50d9 ("kernel: bump 4.14 to 4.14.154")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Wed, 20 Nov 2019 06:57:36 +0000 (07:57 +0100)]
brcm2708: remove useless patches
The first adds some stuff while the second one
just reverts it.
Remove both patches.
This is done is a separate commit on purpose to make it clear.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Tue, 19 Nov 2019 11:09:03 +0000 (12:09 +0100)]
mac80211: refresh patches
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Wed, 6 Nov 2019 12:38:51 +0000 (13:38 +0100)]
mac80211: backport upstream fixes
This potentially fixes some issues seen on IBSS
when interfaces go out of range and then re-appear.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Tue, 19 Nov 2019 09:38:45 +0000 (10:38 +0100)]
toolchain/gcc: bump to 7.5.0
This updates the GCC to the next minor release which fixes +213 bugs.
Tested on ARMv6, ARMv7, MIPS R2, x86
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 18 Nov 2019 09:17:50 +0000 (10:17 +0100)]
kernel: bump 4.19 to 4.19.84
Refreshed all patches.
Altered patches:
- 950-0748-net-bcmgenet-Workaround-for-Pi-4B-network-issue.patch
- 950-0754-Revert-net-bcmgenet-Workaround-for-Pi-4B-network-iss.patch
- 902-debloat_proc.patch
Remove upstreamed:
- 150-MIPS-bmips-mark-exception-vectors-as-char-arrays.patch
New symbols:
X86_INTEL_MPX
X86_INTEL_MEMORY_PROTECTION_KEYS
X86_INTEL_TSX_MODE_OFF
X86_INTEL_TSX_MODE_ON
X86_INTEL_TSX_MODE_AUTO
Compile-tested on: cns3xxx, x86_64
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 18 Nov 2019 09:17:24 +0000 (10:17 +0100)]
kernel: bump 4.14 to 4.14.154
Refreshed all patches.
Altered patches:
- 902-debloat_proc.patch
- 040-dmaengine-qcom-bam-Process-multiple-pending-descript.patch
- 807-usb-support-layerscape.patch
- 809-flexcan-support-layerscape.patch
- 816-pcie-support-layerscape.patch
Remove upstreamed:
- 150-MIPS-bmips-mark-exception-vectors-as-char-arrays.patch
- 303-spi-nor-enable-4B-opcodes-for-mx66l51235l.patch
New symbols:
X86_INTEL_MPX
X86_INTEL_MEMORY_PROTECTION_KEYS
X86_INTEL_TSX_MODE_OFF
X86_INTEL_TSX_MODE_ON
X86_INTEL_TSX_MODE_AUTO
SGL_ALLOC
Compile-tested on: cns3xxx, x86_64
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 18 Nov 2019 09:08:18 +0000 (10:08 +0100)]
kernel: bump 4.9 to 4.9.202
Refreshed all patches.
Altered patches:
- 902-debloat_proc.patch
Compile-tested on: none
Runtime-tested on: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Adrian Schmutzler [Thu, 14 Nov 2019 12:01:39 +0000 (13:01 +0100)]
ar71xx: fix buttons for TP-Link TL-WDR4900 v2
TP-Link TL-WDR4900 v2 only has one combined WPS/Reset button, so
don't set up an RFKILL for this device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Thu, 14 Nov 2019 11:45:15 +0000 (12:45 +0100)]
ar71xx: fix LED setup for TL-WDR4900 v2
In ar71xx there is only one combined mach file for Archer C5/C7 and
TL-WDR4900 v2. This one uses the same LED struct for all devices,
defining "green" LEDs for them. However, WDR4900 uses blue front
LEDs, while only C5/C7 uses green ones. Despite, in base-files
WDR4900 is actually set up with "blue" for the mentioned LEDs.
Thus, this patch creates a separate LED struct for WDR4900, so the
LEDs can be set up correctly. Despite, the wlan5g LED is removed as
it is controlled by ath9k chip for WDR4900 (in contrast to C5/C7).
Note: While front LEDs are blue, USB LEDs (on the back) are green,
so colors are mixed intentionally for the WDR4900 v2.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Mon, 18 Nov 2019 23:14:38 +0000 (00:14 +0100)]
ath79: fix DTS node names for Ubiquiti XM partitions
Some node names were inconsistent with the reg property. Fix it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hauke Mehrtens [Mon, 18 Nov 2019 06:05:41 +0000 (07:05 +0100)]
mac80211: Adapt to changes to skb_get_hash_perturb()
The skb_get_hash_perturb() function now takes a siphash_key_t instead of
an u32. This was changed in commit
55667441c84f ("net/flow_dissector:
switch to siphash"). Use the correct type in the fq header file
depending on the kernel version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Rafał Miłecki [Mon, 18 Nov 2019 13:45:59 +0000 (14:45 +0100)]
mac80211: brcmfmac: fix PCIe reset crash and WARNING
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Daniel Golle [Mon, 18 Nov 2019 11:57:54 +0000 (12:57 +0100)]
base-files: include 'reconf' in help output of 'wifi' command
Reported-by: Dirk Brenken <dev@brenken.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
John Crispin [Sun, 17 Nov 2019 17:13:28 +0000 (18:13 +0100)]
mediatek: pass console inside bootargs on mt7629
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Sun, 17 Nov 2019 17:12:08 +0000 (18:12 +0100)]
mediatek: drop leading + from config
Signed-off-by: John Crispin <john@phrozen.org>
Sungbo Eo [Mon, 7 Oct 2019 12:33:51 +0000 (21:33 +0900)]
ramips: set uImage name of WeVO 11AC NAS and W2914NS v2
The stock firmware and bootloader only accept uImage with names that
match certain patterns. This patch enables OpenWrt installation from
stock firmware without having to reflash the bootloader or access the
UART console.
Installation via web interface:
1. Flash **initramfs** image through the stock web interface.
2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Adrian Schmutzler [Thu, 14 Nov 2019 11:26:05 +0000 (12:26 +0100)]
ar71xx: fix MAC address setup for TL-WDR4900 v2
The MAC address setup of the TL-WDR4900 v2 is different from the
C5/C7. This aligns ar71xx with the setup in ath79:
wlan0 (5GHz) : -2
wlan1 (2.4GHz) : -1
eth1 (LAN) : 0
eth0 (WAN) : 1
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Christian Lamparter [Sat, 16 Nov 2019 21:42:07 +0000 (22:42 +0100)]
ath79: remap D-Link DIR-859 A1 WPS button to WPS
The WPS button was mapped to the restart/reset. This patch
changes it to emit the KEY_WPS_BUTTON keycode so pressing
the WPS button does initiate WPS.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Sat, 16 Nov 2019 21:37:51 +0000 (22:37 +0100)]
ramips: assign correct key-code to wps buttons
The ASUS WL-330N(3G) and the Edimax RG21S had the
reset keycode assigned to the WPS button. This patch
changes all three devices to use KEY_WPS_BUTTON in
the hopes that this fixes unwanted restarts/
unexpected behavior from the users point of view.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Daniel Golle [Sat, 16 Nov 2019 15:29:45 +0000 (16:29 +0100)]
mac80211: detect existing interface before adding
Keep existing wdev when creating new nl80211 interfaces if phy and
type match, delete it otherwise.
To make this work, also remove left-over debugging function which
prevented the return-value of the 'iw' command to be taken into
account in mac80211_iw_interface_add().
As 4addr-mode (WDS) was setup during interface creation for station
interfaces, also set it after interface creation to make sure an
existing sta interface ends up with the right mode.
Fixes: a5bc9787d4 ("mac80211: add support for dynamically
reconfiguring wifi")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sat, 16 Nov 2019 14:49:44 +0000 (15:49 +0100)]
Revert "mac80211: restore mac80211_interface_cleanup()"
This reverts commit
000b7687bc50be5b0f1161f4bf8ceb85c495c395.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Jeff Kletsky [Fri, 15 Nov 2019 16:51:43 +0000 (08:51 -0800)]
ath79: fix firmware partition attributes for GL-AR300M16 and -Lite
During the introduction of the ath79/nand images for the GL-AR300M
series the firmware partition label and compatible were altered,
but the necessary adjustments have not been made for the
GL-AR300M16 and the GL-AR300M-Lite. This will result in a
non-bootable partition setup for these devices.
This patch adds the necessary definitions to those two devices.
Fixes: 55e6c903ae20 ("ath79: GL-AR300M: provide NAND support;
increase to 4 MB kernel")
Fixes: b591cabd3989 ("ath79: add GL.iNet GL-AR300M16 as NOR-only
board")
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
[extend commit message, alter commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
John Crispin [Fri, 15 Nov 2019 06:52:57 +0000 (07:52 +0100)]
mediatek: drop accidentially commited file
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Fri, 15 Nov 2019 06:51:32 +0000 (07:51 +0100)]
mediatek: fix bootup problem on mt7629 EVB
Signed-off-by: John Crispin <john@phrozen.org>
Adrian Schmutzler [Thu, 14 Nov 2019 16:26:44 +0000 (17:26 +0100)]
ath79: fix sysupgrade from ar71xx for WNDR3700 V2 and WNDR3800(CH)
ar71xx has just one board name "wndr3700" for WNDR3700 V1/V2,
WNDR3800 and WNDR3800CH, whereas ath79 provides separate images for
the boards. So, update SUPPORTED_DEVICES to store the correct
ar71xx board names.
Fixes: FS#2510
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Paul Blazejowski [Wed, 13 Nov 2019 19:19:32 +0000 (14:19 -0500)]
ath79: add support for Netgear WNDR3700v4
This patch adds ath79 support for Netgear WNDR3700v4.
Router was previously supported by ar71xx target only.
Note: device requires 'ar934x-nand' driver in kernel.
Specification
=============
* Description: Netgear WNDR3700v4
* Loader: U-boot
* SOC: Atheros AR9344 (560 MHz)
* RAM: 128 MiB
* Flash: 128 MiB (NAND)
- U-boot binary: 256 KiB
- U-boot environment: 256 KiB
- ART: 256 KiB
- POT: 512 KiB
- Language: 2 MiB
- Config: 512 KiB
- Traffic Meter: 3 MiB
- Firmware: 25 MiB
- ART Backup: 256 KiB
- Reserved: 96 MiB
* Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) (AR8327)
* Wireless:
- 2.4 GHz b/g/n (internal)
- 5 GHz a/n (AR9580)
* USB: yes, 1 x USB 2.0
* Buttons:
- Reset
- WiFi (rfkill)
- WPS
* LEDs:
- Power (amber/green)
- WAN (amber/green)
- WLAN 2G (green)
- WLAN 5G (blue)
- 4 x LAN (amber/green)
- USB (green)
- WPS (amber/green)
* UART: 4-pin connector JP1, 3.3V (Vcc, TX, RX, GND), 115200 8N1
* Power supply: DC 12V 2.5A
* MAC addresses: LAN=WLAN2G on case label, WAN +1, WLAN5G +2
Installation
============
* TFTP recovery
* TFTP via U-boot prompt
* sysupgrade
* Web interface
Note about partitioning: firmware partition offset (0x6c0000) is
hardcoded into vendor's u-boot, so this partition cannot be moved
and resized to include Netgear-specific flash areas (pot, language,
config, traffic_meter) not used by OpenWrt.
Test build configuration
========================
CONFIG_TARGET_ath79=y
CONFIG_TARGET_ath79_nand=y
CONFIG_TARGET_ath79_nand_DEVICE_netgear_wndr3700-v4=y
CONFIG_ALL_KMODS=y
CONFIG_DEVEL=y
CONFIG_CCACHE=y
CONFIG_COLLECT_KERNEL_DEBUG=y
CONFIG_IMAGEOPT=y
Signed-off-by: Paul Blazejowski <paulb@blazebox.homeip.net>
Michal Cieslakiewicz [Wed, 13 Nov 2019 19:19:31 +0000 (14:19 -0500)]
ath79: split dts file for Netgear WNDR4300
Move board configuration to dtsi file in preparation for WNDR3700v4
router support.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Adrian Schmutzler [Thu, 14 Nov 2019 12:03:49 +0000 (13:03 +0100)]
ath79: fix indent in TP-Link TL-WDR4900 v2 DTS
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Thu, 14 Nov 2019 11:19:16 +0000 (12:19 +0100)]
ath79: improve common DTSI name for TP-Link Archer C5, C7 v1/v2
As the former qca9558_tplink_archer-c7.dtsi is also used for
Archer C5 v1 this patch removes the number from the DTSI name
to indicate that.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Petr Štetiar [Thu, 14 Nov 2019 21:42:41 +0000 (22:42 +0100)]
fwtool: update to latest Git head
8f7fe925ca20 cmake: use extra compiler warnings only on gcc6+
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Thu, 14 Nov 2019 21:31:02 +0000 (22:31 +0100)]
uci: update to latest Git head
8dd50da20de0 lua: fix error handling
a2cab3b088a2 ucimap: fix possible use of memory after it is freed
9cf978bc7964 delta: prevent possible null pointer use
7736f497d2d9 cli: remove unused variable assigment
39093f3b040d lua: fix memory leak in set method
19ceff323f1e lua: fix memory leak in changes method
18049a84fe40 tests: add cram based unit tests
2b549cc050de lua: fix copy&paste in error string
f5dd5217d627 cli: fix realloc issue spotted by cppcheck
af59f86a0db9 iron out all extra compiler warnings
1637d2918692 tests: shunit2: run all tests under Valgrind by default
c1af73bfb023 cmake: enable extra compiler checks
be69504e3666 cmake: build Lua module only if enabled
38a2f12ec5ab tests: shunit2: fix issues reported by shellcheck
266fc9e94c1e add initial GitLab CI support
17d6144a49c6 tests: shunit2: make it working under CMake
a6e8bbefd860 cmake: add unit testing option and shunit2 tests
0ca93fec701a test: move shunit2 tests under standalone subdirectory
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Thu, 14 Nov 2019 20:06:47 +0000 (21:06 +0100)]
libnl-tiny: update to latest Git head
0219008cc876 remove never used err variable assignment disliked by scan-build
7ce813fcd667 silence use after the free clang analyzer warning
1f73b6a8e678 use offsetof macro to make scan-build happy
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Thomas Weißschuh [Thu, 14 Nov 2019 15:41:10 +0000 (16:41 +0100)]
build: prereq: add support for Python 3.8
Add support for Python 3.8 which was released Oct. 14, 2019.
Signed-off-by: Thomas Weißschuh <thomas@t-8ch.de>
[added missing commit description, simplified version check]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Thu, 14 Nov 2019 15:50:18 +0000 (16:50 +0100)]
build: prereq: simplify Python 3 version checks
We don't need to check if python3.5 binary is actually Python 3.5+.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Peter Stadler [Tue, 12 Nov 2019 14:54:53 +0000 (15:54 +0100)]
base-files: rc.common: fix missing EXTRA_HELP texts
Commit
ed5b9129d7a4 ("base-files: implement generic service_running")
has added EXTRA_HELP variable, thus overriding already available
EXTRA_HELP text available in other init scripts, resulting in the
missing help text from services like dropbear for example.
So fix this regression by appending EXTRA_HELP text provided by the
other init scripts into the one provided by the script itself.
Fixes: ed5b9129d7a4 ("base-files: implement generic service_running")
Signed-off-by: Peter Stadler <peter.stadler@student.uibk.ac.at>
[commit title/description facelift, fixes tag, fixed From:, pkg bump]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Mon, 11 Nov 2019 21:14:21 +0000 (22:14 +0100)]
ath79: remove obsolete OF PCI related config symbols
Those symbols were removed in kernel 4.16:
commit
4670d610d59233b017a6ea1fa25bbf06dabbff42
Author: Rob Herring <robh@kernel.org>
PCI: Move OF-related PCI functions into PCI core
Fixes: FS#2588
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Mon, 11 Nov 2019 20:37:45 +0000 (21:37 +0100)]
kernel-build: fix kernel_menuconfig breakage by forcing YACC
Commit
965f341aa9fd ("build: fix host menu config targets using
ncurses") has moved host's path with pkg-config (usually /usr/bin) at
the first place in PATH variable, which is now causing issues with bison
as BISON_PKGDATADIR points into STAGING_DIR_HOST, but the actual bison
used is the one under host PATH (usually /usr/bin/bison), leading to the
following strange failures:
$ make target/linux/clean kernel_menuconfig V=sc
export MAKEFLAGS= ;make -C /somewhere/linux-4.19.81 menuconfig
make -f ./scripts/Makefile.build obj=scripts/kconfig menuconfig
...
bison -oscripts/kconfig/zconf.tab.c -t -l scripts/kconfig/zconf.y
staging_dir/host/bin/m4: cannot open `staging_dir/host/share/bison/bison.m4': No such file or directory
staging_dir/host/bin/m4: cannot open `staging_dir/host/share/bison/c-skel.m4': No such file or directory
...
gcc -Wp,-MD,scripts/kconfig/.zconf.tab.o.d <...snip...> -o scripts/kconfig/zconf.tab.o scripts/kconfig/zconf.tab.c
gcc: error: scripts/kconfig/zconf.tab.c: No such file or directory
gcc: fatal error: no input files
Fix this by forcing usage of bison under STAGING_DIR_HOST/bin via YACC
make variable.
Cc: Thomas Albers <thomas.gameiro@gmail.com>
Cc: Stijn Tintel <stijn@linux-ipv6.be>
Cc: Eneas U de Queiroz <cotequeiroz@gmail.com>
Tested-by: Ivan Revyakin <LovingFox@GMail.com>
Tested-by: Thomas Albers <thomas.gameiro@googlemail.com>
Ref: https://forum.openwrt.org/t/bpi-r64-kernel-4-19-kernel-menuconfig-error
Fixes: 965f341aa9fd ("build: fix host menu config targets using ncurses")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Sungbo Eo [Mon, 11 Nov 2019 16:16:28 +0000 (01:16 +0900)]
kernel: fix typo in fb-sys-fops autoload
AutoLoad parameter must match the exact kernel module name. Fix it.
Fixes: 125f1ce9ad0c ("kernel: video: add DRM core and IMX DRM support for HDMI/LVDS")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Roger Pueyo Centelles [Wed, 13 Nov 2019 15:18:59 +0000 (09:18 -0600)]
ath79: include rssileds package for ubnt devices with LEDs
Some Ubiquiti devices had the RSSI LEDs configured in 01_leds but
were missing the rssileds package, while others that don't have
RSSI LEDS had the package included.
This commit includes the rssileds package only for those devices
that need it.
Tested on a NanoStation M XW.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Daniel Golle [Thu, 14 Nov 2019 13:02:56 +0000 (14:02 +0100)]
mac80211: restore mac80211_interface_cleanup()
Changes introduced for dynamic wifi reconfiguration left behind
unmanaged interface types. Restore parts of the old function to
also clean (unencrypted, non-DFS) mesh and ad-hoc interfaces.
Fixes: a5bc9787d4 ("mac80211: add support for dynamically
reconfiguring wifi")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Jeff Kletsky [Sun, 2 Jun 2019 15:18:34 +0000 (08:18 -0700)]
ath79: GL-AR750S: provide NAND support; increase kernel to 4 MB
The GL.iNet GL-AR750S has been supported by the ar71xx and ath79
platforms with access to its 16 MB NOR flash, but not its 128 MB
SPI NAND flash.
This commit provides support for the NAND through the upstream
SPI-NAND framework.
At this time, the OEM U-Boot appears to only support loading the
kernel from NOR. This configuration is preserved as this time,
with the glinet,gl-ar750s-nand name reserved for a potential,
future, NAND-only boot.
The family of GL-AR750S devices on the ath79 platform now includes:
* glinet,gl-ar750m-nor-nand "nand" target
* glinet,gl-ar750m-nor "nand" target (NAND-aware)
NB: This commit increases the kernel size from 2 MB to 4 MB
"Force-less" sysupgrade is presently supported from the current
versions of following NOR-based firmwre images to the version of
glinet,gl-ar750s-nor firmware produced by this commit:
* glinet,gl-ar750s -- OpenWrt 19.07 ar71xx
* glinet,gl-ar750s -- OpenWrt 19.07 ath79
Users who have sucessfully upgraded to glinet,gl-ar750m-nor may then
flash glinet,gl-ar750m-nor-nand with sysupgrade to transtion to the
NAND-based variant.
Other upgrades to these images, including directly to the NAND-based
glinet,gl-ar750s-nor-nand firmware, can be accomplished through U-Boot.
NB: See "ath79: restrict GL-AR750S kernel build-size to 2 MB" which
enables flashing of NAND factory.img with the current GL-iNet U-Boot,
"U-Boot
1.1.4-gcf378d80-dirty (Aug 16 2018 - 07:51:15)"
The GL-AR750S OEM U-Boot allows upload and flashing of either NOR
firmware (sysupgrade.bin) or NAND firmware (factory.img) through its
HTTP-based GUI. Serial connectivity is not required.
The glinet,gl-ar750s-nor and glinet,gl-ar750s-nor-nand images
generated after this commit flash each other directly.
This commit changes the control of the USB VBUS to gpio-hog from
regulator-fixed introduced by commit
0f6b944c92. This reduces the
compressed kernel size by ~14 kB, with no apparent loss of
functionality. No other ath79-nand boards are using regulator-fixed
at this time.
Note: mtd_get_mac_binary art 0x5006 does not return the proper MAC
and the GL.iNet source indicates that only the 0x0 offset is valid
The ar71xx targets are unmodified.
Cc: Alexander Wördekemper <alexwoerde@web.de>
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Jeff Kletsky [Sun, 2 Jun 2019 13:43:00 +0000 (06:43 -0700)]
ath79: add GL.iNet GL-AR300M16 as NOR-only board
The GL.iNet GL-AR300M series of devices includes variants without NAND
and only the 16 MB NOR flash. These include the GL-AR300M16 and the
GL-AR300M-Lite (already with its own board name).
This board-name addition provides disambiguation from the NAND-bearing
GL-AR300M devices, both for OpenWrt code and for end users.
Kernel and firmware support for NAND and UBI will add ~320 kB to the
overall firmware size at this time. This NOR-only option continues to
provide more compact firmware for both the GL-AR300M16 as well as
those who wish to use it as an alternate or primary, NOR-resident
firmware on the GL-AR300M.
The ar71xx targets are unmodified.
Installation
------------
Install through OEM U-Boot (HTTP-based) or `sysupgrade --force` when
booted from NOR and running OEM or OpenWrt, NOR-based firmware.
As one of the intentions is disambiguation from NAND-bearing units,
users who have flashed this firmware onto a device with NAND would
need to use U-Boot or `sysupgrade --force` to flash firmware that
again supports NAND.
There are no additional SUPPORTED_DEVICES as it is not possible to
determine if a device does or does not have NAND based on
either the OEM's or OpenWrt's board names prior to this patch.
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Jeff Kletsky [Sun, 2 Jun 2019 00:51:17 +0000 (17:51 -0700)]
ath79: GL-AR300M: provide NAND support; increase to 4 MB kernel
The GL.iNet GL-AR300M has been supported by the ar71xx and ath79
platforms with access to its 16 MB NOR flash, but not its 128 MB
SPI NAND flash.
This commit provides support for the NAND through the upstream
SPI-NAND framework. Devices with both NOR and NAND flash can support
independent firmware on each, with U-Boot able to boot from either.
The OEM U-Boot will fall back to the NOR firmware after three
"unsuccessful" boots.
The family of GL-AR300M devices on the ath79 platform now includes:
* glinet,gl-ar300m-lite "generic" target, NOR-only board
* glinet,gl-ar300m-nand "nand" target
* glinet,gl-ar300m-nor "nand" target (NAND-aware)
NB: This commit increases the kernel size from 2 MB to 4 MB
"Force-less" sysupgrade is presently supported from the current
versions of following NOR-based firmwre images to the version of
glinet,gl-ar300m-nor firmware produced by this commit:
* gl-ar300m -- OEM v3 NOR ar71xx (openwrt-ar300m16-*.bin)
* gl-ar300m -- OpenWrt 18.06 ar71xx
* gl-ar300m -- OpenWrt 19.07 ar71xx
Other upgrades to these images should be performed through U-Boot.
The GL-AR300M OEM U-Boot allows upload and flashing of either NOR
firmware (sysupgrade.bin) or NAND firmware (factory.img) through its
HTTP-based GUI. Serial connectivity is not required.
The glinet,gl-ar300m-nand and glinet,gl-ar300m-nor images generated
after this commit should safely flash each other using sysupgrade.
The boot counter is implemented by the OEM using u-boot-env. At this
time, it does not appear that the switch on the side of the unit can
be used to select NOR vs. NAND boot and the fail-over is only from
NAND to NOR. To save flash wear, it is only reset when running the
glinet,gl-ar300m-nand firmware.
NAND-specific base-files are used to remove impact on existing
generic and tiny targets.
As there is now no "generic" build appropriate for the GL-AR300M16,
(or for users of the GL-AR300M that do not need access to NAND)
it will be introduced in a subsequent commit.
Note: `mtd_get_mac_binary art 0x6` does not return the proper MAC
and the GL.iNet source indicates that only the 0x0 offset is valid
The ar71xx targets are unmodified.
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Jeff Kletsky [Tue, 14 May 2019 16:47:40 +0000 (09:47 -0700)]
ath79: prepare NAND subtarget for upstream support of SPI NAND
Linux 4.19 supplies the upstream spi-nand framework,
permitting porting and support of boards with SPI NAND.
* Adjusted nand/target.mk to provide FEATURES += squashfs nand
* Updated config-default to provide current MTD and UBI support
Defaults selected for:
CONFIG_MTD_UBI_WL_THRESHOLD=4096
CONFIG_MTD_UBI_BEB_LIMIT=20
# CONFIG_MTD_UBI_FASTMAP is not set
# CONFIG_MTD_UBI_GLUEBI is not set
The bad-block reservation limit technically should be 21 for Paragon
SPI NAND but most other devices in the class are 20 blocks per Gbit.
In Linux 5.2 this is specified on a per-chip basis through NAND_MEMORG
Contents adjusted to remove declarations provided at the target level
by commit
08a134820f5 (Oct 23, 2019) ath79: enable PCI for whole target
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Tested-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Piotr Dymacz [Sun, 3 Nov 2019 11:17:52 +0000 (12:17 +0100)]
uboot-envtools: ramips: add support for ALFA Network Quad-E4G
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Piotr Dymacz [Sun, 3 Nov 2019 11:12:44 +0000 (12:12 +0100)]
ramips: add support for ALFA Network Quad-E4G
ALFA Network Quad-E4G is a universal Wi-Fi/4G platform, which offers
three miniPCIe (PCIe, USB 2.0, SIM) and a single M.2 B-key (dual-SIM,
USB 3.0) slots, RTC and five Gigabit Ethernet ports with PoE support.
Specification:
- MT7621A (880 MHz)
- 256/512 MB of RAM (DDR3)
- 16/32+ MB of FLASH (SPI NOR)
- optional second SPI flash (8-pin WSON/SOIC)
- 1x microSD (SDXC) flash card reader
- 5x 10/100/100 Mbps Ethernet, with passive PoE support (24 V) in LAN1
- optional 802.3at/af PoE module for WAN
- 3x miniPCIe slot (with PCIe and USB 2.0 buses, micro SIM and 5 V)
- 1x M.2/NGFF B-key 3042 (USB 3.0/2.0, mini + micro SIM)
- RTC (TI BQ32002, I2C bus) with backup battery (CR2032)
- external hardware watchdog (EM Microelectronic EM6324)
- 1x USB 2.0 Type-A
- 1x micro USB Type-B for system serial console (Holtek HT42B534)
- 11x LED (5 for Ethernet, 5 driven by GPIO, 1x power indicator)
- 3x button (reset, user1, user2)
- 1x I2C (4-pin, 2.54 mm pitch) header on PCB
- 4x SIM (6-pin, 2.00 mm pitch) headers on PCB
- 2x UART2/3 (4-pin, 2.54 mm pitch) headers on PCB
- 1x mechanical power switch
- 1x DC jack with lock (24 V)
Other:
- U-Boot selects default SIM slot, based on value of 'default_sim' env
variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This board
has additional logic circuit for M.2 SIM switching. The 'sim-select'
will work only if both SIM slots are occupied. Otherwise, always slot
with SIM inside is selected, no matter 'sim-select' value.
- U-Boot enables power in all three miniPCIe and M.2 slots before
loading the kernel
- this board supports 'dual image' feature (controlled by 'dual_image'
U-Boot environment variable)
- all three miniPCIe slots have additional 5 V supply on pins 47 and 49
- the board allows to install up to two oversized miniPCIe cards (vendor
has dedicated MediaTek MT7615N/D cards for this board)
- this board has additional logic circuit controlling PERSTn pins inside
miniPCIe slots. By default, PERSTn (GPIO19) is routed to all miniPCIe
slots but setting GPIO22 to high allows PERSTn control per slot, using
GPIO23-25 (value is inverted)
You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:
1. Power the device with reset button pressed, the modem LED will start
blinking slowly and after ~3 seconds, when it starts blinking faster,
you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Piotr Dymacz [Fri, 1 Nov 2019 20:40:37 +0000 (21:40 +0100)]
ramips: mt7621: refresh kernel config
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Piotr Dymacz [Wed, 30 Oct 2019 21:55:42 +0000 (22:55 +0100)]
ramips: provide label MAC for ALFA Network Tube-E4G
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Piotr Dymacz [Wed, 30 Oct 2019 20:48:09 +0000 (21:48 +0100)]
uboot-envtools: ramips: add support for ALFA Network R36M-E4G
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Piotr Dymacz [Tue, 29 Oct 2019 23:10:40 +0000 (00:10 +0100)]
ramips: add support for ALFA Network R36M-E4G
ALFA Network R36M-E4G is a dual-SIM, N300 Wi-Fi, compact size platform
based on MediaTek MT7620A WiSoC. This product is designed for operation
with 4G modem (can be bought in bundle with Quectel EC25, EG25 or EP06)
but supports also Wi-Fi modules (miniPCIe slot has USB and PCIe buses).
Specification:
- MT7620A (580 MHz)
- 64/128/256 MB of RAM (DDR2)
- 16/32+ MB of FLASH (SPI NOR)
- 2x 10/100 Mbps Ethernet, with passive PoE support (24 V)
- 2T2R 2.4 GHz (MT7620A), with ext. LNA (RFFM4227)
- 1x miniPCIe slot (with PCIe and USB 2.0 buses and optional 5 V)
- 2x SIM slot (mini, micro) with detect and switch driven by GPIO
- 2x u.fl antenna connectors (for Wi-Fi)
- 8x LED (7 driven by GPIO)
- 2x button (reset, wifi)
- 2x UART (4-pin/2.54 mm pitch, 10-pin/1.27 mm pitch) headers on PCB
- 1x I2C (4-pin, 1.27 mm pitch) header on PCB
- 1x LED (8-pin, 1.27 mm pitch) header on PCB
- 1x DC jack with lock (12 V)
Other:
- there is a dedicated, 4-pin connector for optional RTC module (Holtek
HT138x) with 'enable' input, not available at the time of preparing
support for this board
- miniPCIe slot supports additional 5 V supply on pins 47 and 49 but a
jumper resistor (R174) is not installed by default
- U-Boot selects default SIM slot, based on value of 'default_sim' env
variable: '1' or unset -> SIM1 (mini), '2' -> SIM2 (micro). This will
work only if both slots are occupied, otherwise U-Boot will always
select slot with SIM card inside (user can override it later, in
user-space)
- U-Boot resets the modem, using PERSTn signal, before starting kernel
- this board supports 'dual image' feature (controlled by 'dual_image'
U-Boot environment variable)
Flash instruction:
You can use the 'sysupgrade' image directly in vendor firmware which is
based on OpenWrt (make sure to not preserve settings - use 'sysupgrade
-n -F ...' command). Alternatively, use web recovery mode in U-Boot:
1. Power the device with reset button pressed, the modem LED will start
blinking slowly and after ~3 seconds, when it starts blinking faster,
you can release the button.
2. Setup static IP 192.168.1.2/24 on your PC.
3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Piotr Dymacz [Tue, 29 Oct 2019 22:25:56 +0000 (23:25 +0100)]
ramips: support dual image feature on ALFA Network boards
New U-Boot version for MediaTek MT76x8/MT762x based ALFA Network boards
includes support for a 'dual image' feature. Users can enable it using
U-Boot environment variable 'dual_image' ('1' -> enabled).
When 'dual image' feature is enabled, U-Boot will modify DTB and divide
the original 'firmware' flash area into two, equal in size and aligned
to 64 KB partitions: 'firmware' and 'backup'. U-Boot will also adjust
size of 'firmware' area to match installed flash chip size.
U-Boot will load kernel from active partition which is marked with env
variable 'bootactive' ('1' -> first partition, '2' -> second partition)
and rename both partitions accordingly ('firmware' <-> 'backup').
There are 3 additional env variables used to control 'dual image' mode:
- bootlimit - maximum number of unsuccessful boot tries (default: '3')
- bootcount - current number of boot tries
- bootchanged - flag which informs that active partition was changed; if
it is set and 'bootcount' reaches 'bootlimit' value,
U-Boot will start web-based recovery which then updates
both partitions with provided image
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Russell Senior [Tue, 12 Nov 2019 23:33:48 +0000 (15:33 -0800)]
base-files: add /usr/share/libubox/jshn.sh to sysupgrade stage2
Discovered recent changes had broken sysupgrade for ar71xx mikrotik
rb-493g, traced the problem to missing /usr/share/libubox/jshn.sh after
switching to tmpfs.
Signed-off-by: Russell Senior <russell@personaltelco.net>
Sungbo Eo [Wed, 13 Nov 2019 14:23:17 +0000 (23:23 +0900)]
ramips: add usb-ledtrig-usbport to DEVICE_PACKAGES of CY-SWR1100
CY-SWR1100 has a USB LED but kmod-usb-ledtrig-usbport is missing
in default images. This commit adds it.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[changed commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sungbo Eo [Wed, 13 Nov 2019 14:47:14 +0000 (23:47 +0900)]
ramips: change status LED of Samsung CY-SWR1100
Use power LED for status indication and free WPS LED for other uses.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Wed, 13 Nov 2019 14:29:21 +0000 (23:29 +0900)]
ramips: improve Samsung CY-SWR1100 support
This patch does the following:
- rename "devdata" flash partition and make it read-only
- switch from gpio-keys-polled to gpio-keys
- add missing power LED
- set correct PCI ID to compatible string in wifi node
- remove ralink,5ghz property in wifi node
- provide label MAC address
Rename devdata partition to devconf as indicated in the stock firmware
partition table:
00030000-
00040000: "devdata"
00040000-
00050000: "devconf"
Power LED can be controlled by SoC GPIO. Add it in the dts leds node.
RT3092L supports only bgn mode, so it is unnecessary to disable 5GHz band.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Wed, 13 Nov 2019 14:22:54 +0000 (23:22 +0900)]
ramips: fix MAC address setup for Samsung CY-SWR1100
Ethernet MAC address setup has been broken since
c3e420f28cf1. Restore
original setting.
Fixes: c3e420f28cf1 ("ramips: Add support for D-Link DCH-M225")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Adrian Schmutzler [Wed, 13 Nov 2019 14:05:29 +0000 (15:05 +0100)]
ar71xx: fix MAC addresses for Archer C5 v1, C7 v1/v2, WDR4900 v2
As discussed in
1d18a14a90c7 ("ath79: really fix TP-Link Archer C7
v2 MAC address"), stock firmware MAC address assignment is
actually as follows:
wlan0 (5GHz) : -1
wlan1 (2.4GHz) : 0
eth1 (LAN) : 0
eth0 (WAN) : 1
This has never been fixed for ar71xx, so let's do it now.
Note that with WDR4900 v2 even both wlan0 and wlan1 where assigned
to basemac-1 before ...
Fixes: FS#408
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sun, 10 Nov 2019 23:22:33 +0000 (00:22 +0100)]
ath79: read label MAC address from flash instead of using phy0/phy1
This replaces all uses of $(cat /sys/class/ieee80211/phyX/macaddress)
by retrieval from the proper flash locations. This will make
02_network independent of WiFi setup again.
For future reference:
The MAC addresses of the FRITZ!WLAN Repeater 300E can be extracted
from the urlader key value store:
maca *:6B
macb *:6C
macwlan *:6D
macdsl *:6E
and be set by e.g.
addr=$(fritz_tffs -n maca -i $(find_mtd_part "tffs (1)"))
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sun, 10 Nov 2019 23:18:45 +0000 (00:18 +0100)]
ramips: read label MAC address from flash instead of using phy0/phy1
This replaces all uses of $(cat /sys/class/ieee80211/phyX/macaddress)
by retrieval from the proper flash locations. This will make
02_network independent of WiFi setup again.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Thu, 7 Nov 2019 21:29:21 +0000 (22:29 +0100)]
base-files: remove shebang from uci-defaults files
uci-defaults are sourced and non-executable, so they do not require
a shebang.
While at it, apply consistent naming scheme.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Kevin Darbyshire-Bryant [Tue, 12 Nov 2019 14:27:06 +0000 (14:27 +0000)]
build: image: posix compatibility cut v head
Replace 2 instances of non posix use of 'head' with posix compliant
'cut'.
'head -c n' cuts 'n' bytes from the passed string and happens to work on
Linux & Mac OS X even though '-c' is not posix.
'head --bytes n' does the same thing and happens to work on linux but
not on Mac OS X and is also not posix.
'cut -b1-8' cuts the first 8 bytes from the passed string and is posix
compliant, hence works on Linux & Mac OS X.
Our usage of 'head --bytes' was particularly unfortunate since it was
used to calculated the RootFS UUID passed to grub - the net result being
a non-functioning system waiting for the root file system to appear.
Thanks to karlp, ynezz & others for pointers on solving this.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
John Crispin [Wed, 30 Oct 2019 15:59:14 +0000 (16:59 +0100)]
base-files: add 'wifi reconf'
Now that netifd and hostapd allow dynamic reconfiguration, add a
command to trigger it.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
John Crispin [Wed, 30 Oct 2019 15:58:19 +0000 (16:58 +0100)]
mac80211: add support for dynamically reconfiguring wifi
Change scripts to use ubus interface of hostapd/wpa_supplicant to
add/remove/modify wireless interfaces instead of (re-)starting the
services.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
John Crispin [Wed, 30 Oct 2019 15:57:22 +0000 (16:57 +0100)]
hostapd: add ubus reload
Add ubus interface to hostapd and wpa_supplicant to allow dynamically
reloading wiface configuration without having to restart the hostapd
process.
As a consequence, both hostapd and wpa_supplicant are now started
persistently on boot for each wifi device in the system and then
receive ubus calls adding, modifying or removing interface
configuration.
At a later stage it would be desirable to reduce the services to one
single instance managing all radios.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 31 Oct 2019 10:30:11 +0000 (11:30 +0100)]
netifd: add dynamic wireless reconfiguration
7a723d0 wireless: add ubus method for reloading configuration
e15147c wireless: make reconf opt-in and allow serializing configuration
Set new option 'reconf' in 'wifi-device' section to enable dynamic
re-configuration on that radio.
If necessary, also set option 'serialize' which forced netifd to
configure interfaces of wireless devices one-by-one.
Both options are disabled by default.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Koen Vandeputte [Wed, 6 Nov 2019 16:19:11 +0000 (17:19 +0100)]
kernel: bump 4.19 to 4.19.82
Refreshed all patches.
Remove upstreamed:
- 950-0295-sc16is7xx-Fix-for-Unexpected-interrupt-8.patch
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Wed, 6 Nov 2019 16:18:34 +0000 (17:18 +0100)]
kernel: bump 4.14 to 4.14.152
Refreshed all patches.
Altered patches:
- 301-arch-support-layerscape.patch
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Wed, 6 Nov 2019 16:11:03 +0000 (17:11 +0100)]
kernel: bump 4.9 to 4.9.199
Refreshed all patches.
Compile-tested on: none
Runtime-tested on: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Adrian Schmutzler [Mon, 11 Nov 2019 18:03:20 +0000 (19:03 +0100)]
ath79: fix SUPPORTED_DEVICES for TP-Link TL-WR1043ND v3
In ar71xx, the board name for the TL-WR1043ND v3 is equal to v2:
tl-wr1043nd-v2
Fix SUPPORTED_DEVICES for v3 in ath79 accordingly.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Manuel Kock [Mon, 11 Nov 2019 12:01:33 +0000 (13:01 +0100)]
lantiq: remove redundant WiFi LED on FRITZ!Box 7320
The led wireless trigger is already set correctly to phy0tpt through the
alias in the device tree.
Signed-off-by: Manuel Kock <github.web@manu.li>
[rephrased commit title]
Signed-off-by: David Bauer <mail@david-bauer.net>
Petr Štetiar [Sat, 9 Nov 2019 13:33:13 +0000 (14:33 +0100)]
fwtool: update to latest Git head
Includes following changes:
9d9d4c284786 fix possible garbage in unitialized char* struct members
dbc1b1b71b24 fix possible copy of null buffer and validation of unitialized header
76d53deef8bb crc32: add missing stdint.h dependency
e5666ed3b47c add cram based unit tests
abe0cf7de053 add initial GitLab CI support
e43042507b4f iron out extra compiler warnings
5df0cd6e1523 convert into CMake project
a7dc0526f819 refactor into separate Git project
adds missing PKG_LICENSE field and converts the package build to utilize
CMake.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Paul Spooren [Mon, 4 Nov 2019 20:55:23 +0000 (10:55 -1000)]
x86,tegra,mvebu: image: use common reproducible IMG_PART_SIGNATURE
These targets are currently using more or less same SIGNATURE variable
which provides unique partition ID/signature, so it makes sense to
refactor it out into common IMG_PART_SIGNATURE variable which could be
reused by all targets.
This is another step in the direction of reproducible OpenWrt images.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[split into separate commit, renamed to IMG_PART_SIGNATURE]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Paul Spooren [Mon, 4 Nov 2019 20:55:23 +0000 (10:55 -1000)]
build: image: add common and reproducible IMG_PART_SIGNATURE variable
x86, mvebu and tegra targets are currently using more or less same
SIGNATURE variable which provides unique partition ID/signature, so it
makes sense to refactor it out into common variable which could be
reused by all targets. While at it, make the content of the variable
reproducible.
Ref: http://lists.infradead.org/pipermail/openwrt-devel/2019-March/016148.html
Signed-off-by: Paul Spooren <mail@aparcar.org>
Suggested-by: Jo-Philipp Wich <jo@mein.io>
[renamed to IMG_PARTSIGNATURE, reworked with epoch+vermagic hash]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Adrian Schmutzler [Mon, 11 Nov 2019 13:48:17 +0000 (14:48 +0100)]
ramips: split further base-files across subtargets
As started in
19724e28c81e ("ramips: split base-files into
subtargets"), this moves some smaller left-over files to the
appropriate base-files folder of their subtarget:
- /etc/init.d/bootcount
- /etc/uci-defaults/04_led_migration
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sun, 10 Nov 2019 23:15:36 +0000 (00:15 +0100)]
ath79: fix identifier for Nanostation M in ath9k caldata extraction
When Nanostation M was renamed from ubnt,nano-m to ubnt,nanostation-m
in commit
f1396ac753cc ("ath79: align naming of Ubiquiti Nanostation M"),
the caldata extraction in 10-ath9k-eeprom was overlooked.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Zoltan HERPAI [Sat, 9 Nov 2019 12:01:50 +0000 (13:01 +0100)]
firmware: intel-microcode: bump to
20190918
* New upstream microcode datafile
20190918
*Might* contain mitigations for INTEL-SA-00247 (RAMBleed), given
the set of processors being updated.
* Updated Microcodes:
sig 0x000306d4, pf_mask 0xc0, 2019-06-13, rev 0x002e, size 19456
sig 0x000306f4, pf_mask 0x80, 2019-06-17, rev 0x0016, size 18432
sig 0x00040671, pf_mask 0x22, 2019-06-13, rev 0x0021, size 14336
sig 0x000406f1, pf_mask 0xef, 2019-06-18, rev 0xb000038, size 30720
sig 0x00050654, pf_mask 0xb7, 2019-07-31, rev 0x2000064, size 33792
sig 0x00050657, pf_mask 0xbf, 2019-08-12, rev 0x500002b, size 51200
sig 0x00050662, pf_mask 0x10, 2019-06-17, rev 0x001c, size 32768
sig 0x00050663, pf_mask 0x10, 2019-06-17, rev 0x7000019, size 24576
sig 0x00050664, pf_mask 0x10, 2019-06-17, rev 0xf000017, size 24576
sig 0x00050665, pf_mask 0x10, 2019-06-17, rev 0xe00000f, size 19456
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Jo-Philipp Wich [Sun, 10 Nov 2019 20:33:47 +0000 (21:33 +0100)]
rpcd: update to latest Git HEAD
77ad0de plugin: avoid truncating numeric values
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
David Bauer [Sun, 10 Nov 2019 19:54:38 +0000 (20:54 +0100)]
ramips: correct Netgear WNDR3700v5 button flag
This adjusts the GPIO state flag to ACTIVE_LOW as FCC pictures indicate
the base board is identical to the one of the R6220.
Fixes commit
3459013257e0 ("ramips: correct R6220 button flag")
Signed-off-by: David Bauer <mail@david-bauer.net>
Zoltan HERPAI [Sun, 25 Aug 2019 20:34:13 +0000 (22:34 +0200)]
firmware: intel-microcode: bump to
20190618
* Implements MDS mitigation (RIDL, Fallout, Zombieload), INTEL-SA-00223
CVE-2018-12126, CVE-2018-12127, CVE-2018-12130, CVE-2019-11091
* Updated Microcodes:
sig 0x000206d6, pf_mask 0x6d, 2019-05-21, rev 0x061f, size 18432
sig 0x000206d7, pf_mask 0x6d, 2019-05-21, rev 0x0718, size 19456
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Zoltan HERPAI [Thu, 16 May 2019 10:32:14 +0000 (12:32 +0200)]
firmware: intel-microcode: bump to
20190514
* New Microcodes:
sig 0x00030678, pf_mask 0x02, 2019-04-22, rev 0x0838, size 52224
sig 0x00030678, pf_mask 0x0c, 2019-04-22, rev 0x0838, size 52224
sig 0x00030679, pf_mask 0x0f, 2019-04-23, rev 0x090c, size 52224
sig 0x000406c3, pf_mask 0x01, 2019-04-23, rev 0x0368, size 69632
sig 0x000406c4, pf_mask 0x01, 2019-04-23, rev 0x0411, size 68608
sig 0x00050657, pf_mask 0xbf, 2019-02-27, rev 0x5000021, size 47104
sig 0x000806e9, pf_mask 0x10, 2018-10-18, rev 0x009e, size 98304
sig 0x000806eb, pf_mask 0xd0, 2018-10-25, rev 0x00a4, size 99328
sig 0x000806ec, pf_mask 0x94, 2019-02-12, rev 0x00b2, size 98304
sig 0x000906ec, pf_mask 0x22, 2018-09-29, rev 0x00a2, size 98304
sig 0x000906ed, pf_mask 0x22, 2019-02-04, rev 0x00b0, size 97280
* Updated Microcodes:
sig 0x000206a7, pf_mask 0x12, 2019-02-17, rev 0x002f, size 12288
sig 0x000306a9, pf_mask 0x12, 2019-02-13, rev 0x0021, size 14336
sig 0x000306c3, pf_mask 0x32, 2019-02-26, rev 0x0027, size 23552
sig 0x000306d4, pf_mask 0xc0, 2019-03-07, rev 0x002d, size 19456
sig 0x000306e4, pf_mask 0xed, 2019-03-14, rev 0x042e, size 16384
sig 0x000306e7, pf_mask 0xed, 2019-03-14, rev 0x0715, size 17408
sig 0x000306f2, pf_mask 0x6f, 2019-03-01, rev 0x0043, size 34816
sig 0x000306f4, pf_mask 0x80, 2019-03-01, rev 0x0014, size 18432
sig 0x00040651, pf_mask 0x72, 2019-02-26, rev 0x0025, size 21504
sig 0x00040661, pf_mask 0x32, 2019-02-26, rev 0x001b, size 25600
sig 0x00040671, pf_mask 0x22, 2019-03-07, rev 0x0020, size 14336
sig 0x000406e3, pf_mask 0xc0, 2019-04-01, rev 0x00cc, size 100352
sig 0x000406f1, pf_mask 0xef, 2019-03-02, rev 0xb000036, size 30720
sig 0x00050654, pf_mask 0xb7, 2019-04-02, rev 0x200005e, size 32768
sig 0x00050662, pf_mask 0x10, 2019-03-23, rev 0x001a, size 32768
sig 0x00050663, pf_mask 0x10, 2019-03-23, rev 0x7000017, size 24576
sig 0x00050664, pf_mask 0x10, 2019-03-23, rev 0xf000015, size 23552
sig 0x00050665, pf_mask 0x10, 2019-03-23, rev 0xe00000d, size 19456
sig 0x000506c9, pf_mask 0x03, 2019-01-15, rev 0x0038, size 17408
sig 0x000506ca, pf_mask 0x03, 2019-03-01, rev 0x0016, size 15360
sig 0x000506e3, pf_mask 0x36, 2019-04-01, rev 0x00cc, size 100352
sig 0x000506f1, pf_mask 0x01, 2019-03-21, rev 0x002e, size 11264
sig 0x000706a1, pf_mask 0x01, 2019-01-02, rev 0x002e, size 73728
sig 0x000806e9, pf_mask 0x10, 2019-04-01, rev 0x00b4, size 98304
sig 0x000806e9, pf_mask 0xc0, 2019-04-01, rev 0x00b4, size 99328
sig 0x000806ea, pf_mask 0xc0, 2019-04-01, rev 0x00b4, size 99328
sig 0x000806eb, pf_mask 0xd0, 2019-03-30, rev 0x00b8, size 98304
sig 0x000806ec, pf_mask 0x94, 2019-03-30, rev 0x00b8, size 97280
sig 0x000906e9, pf_mask 0x2a, 2019-04-01, rev 0x00b4, size 99328
sig 0x000906ea, pf_mask 0x22, 2019-04-01, rev 0x00b4, size 98304
sig 0x000906eb, pf_mask 0x02, 2019-04-01, rev 0x00b4, size 99328
sig 0x000906ec, pf_mask 0x22, 2019-02-14, rev 0x00ae, size 98304
sig 0x000906ed, pf_mask 0x22, 2019-03-17, rev 0x00b8, size 97280
* Implements MDS mitigation (RIDL, Fallout, Zombieload), INTEL-SA-00223
CVE-2018-12126, CVE-2018-12127, CVE-2018-12130, CVE-2019-11091
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Hauke Mehrtens [Sat, 9 Nov 2019 19:10:58 +0000 (20:10 +0100)]
mac80211: Fix dependencies of kmod-rsi91x-usb
Instead of depending on kmod-usb2 make it depend on the normal USB
dependencies. This should hopefully fix some problems seen in the build
bot builds for powerpc_8540.
In addition also activate DRIVER_11N_SUPPORT support.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sat, 9 Nov 2019 19:07:18 +0000 (20:07 +0100)]
strace: Fix build on PowerPC
This patch breaks building on PowerPC, like the mpc85xx_generic
target for me.
Fixes: FS#2585
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
David Bauer [Sat, 9 Nov 2019 18:10:51 +0000 (19:10 +0100)]
ramips: correct R6220 button flag
All buttons on the Netgear R6220 are active-low while they are flagged
as active-high.
The GPIO status reads the following for no buttons pressed:
root@64367-r6220:~# cat /sys/kernel/debug/gpio
gpio-7 ( |wps ) in hi
gpio-8 ( |wifi ) in hi
gpio-14 ( |reset ) in hi
Signed-off-by: David Bauer <mail@david-bauer.net>
projects / openwrt / staging / jogo.git / log