Petr Štetiar [Thu, 24 Mar 2022 05:52:37 +0000 (06:52 +0100)]
imagebuilder: fix broken image generation with external targets
When using external targets there is a symlink being created for the
target under target/linux which then becomes dangling under Image
Builder. Fix it by dereferencing the possible symlink.
Tested on IB with external target, ipq40xx and mvebu.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Stijn Tintel [Thu, 24 Mar 2022 22:46:44 +0000 (00:46 +0200)]
qoriq: remove CONFIG_GDB_SCRIPTS from kernel config
It is disabled in the generic kernel config and not used in any of the
other targets. There was no specific reason for enabling it, so let's be
consistent and remove it from the qoriq kernel config.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
David Bauer [Thu, 24 Mar 2022 22:09:24 +0000 (23:09 +0100)]
mpc85xx: overhaul WS-AP3825i LED setup
As the LED controller is working now, we can make good use of the LEDs
now.
- Drop the model-name prefix
- Rename eth0 / eth1 LEDs to LAN1 / LAN2, as they are labeled as such
on the casing
- Enable wired LEDs in userspace
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Thu, 24 Mar 2022 21:53:43 +0000 (22:53 +0100)]
mpc85xx: move Extreme WS-AP3825i GPIO extender
Move the GPIO extender to the SoC node. Otherwise, the legacy PowerPC
init code will not populate the BUS and thus never probe spi-gpio.
Signed-off-by: David Bauer <mail@david-bauer.net>
Daniel Golle [Thu, 24 Mar 2022 18:40:14 +0000 (18:40 +0000)]
uqmi: fix acquiring PIN status
Evaluating the return value of 'json_load' didn't work in the
intended way resulting in PIN status no longer being read on modems
where --get-pin-status doesn't fail.
Fix this by trying --get-pin-status first and checking if pin1_status
field exists in JSON, and if it doesn't try again with
--uim-get-sim-state.
Fixes: #9501
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Matthias Schiffer [Thu, 24 Mar 2022 08:26:01 +0000 (09:26 +0100)]
ath79: change Ubiquiti UniFi AP model name to include "AP"
While it hasn't always been clear whether the "AP" is part of the model
name on the Ubiquiti website, we include it for all other pre-AC
variants (AP Pro and the AP Outdoor+). Add it to the original UniFi AP
as well for consistency.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Matthias Schiffer [Wed, 23 Mar 2022 21:06:50 +0000 (22:06 +0100)]
ath79: fix label MAC address for Ubiquiti UniFi
The label has the MAC address of eth0, not the WLAN PHY address.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Petr Štetiar [Thu, 24 Mar 2022 05:45:04 +0000 (06:45 +0100)]
zlib: backport security fix for a reproducible crash in compressor
Tavis has just reported, that he was recently trying to track down a
reproducible crash in a compressor. Believe it or not, it really was a
bug in zlib-1.2.11 when compressing (not decompressing!) certain inputs.
Tavis has reported it upstream, but it turns out the issue has been
public since 2018, but the patch never made it into a release. As far as
he knows, nobody ever assigned it a CVE.
Suggested-by: Tavis Ormandy <taviso@gmail.com>
References: https://www.openwall.com/lists/oss-security/2022/03/24/1
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Daniel Golle [Thu, 24 Mar 2022 03:25:28 +0000 (03:25 +0000)]
kernel: set options to make external initramfs reproducible
Run cpio as well as compressors in such ways that they are generating
reproducible output.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 24 Mar 2022 02:56:01 +0000 (02:56 +0000)]
kernel: generic: fix warning in FIT partition parser
Use 'const char *' where necessary to make gcc get quiet.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Wed, 23 Mar 2022 19:34:06 +0000 (19:34 +0000)]
scripts/mkits.sh: replace forgotten '-' with ${REFERENCE_CHAR}
Cosmetical change to improve style in mkits.sh.
Fixes: fd679086473 ("scripts: mkits.sh: Allow legacy @ mode for dts creation")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Wed, 23 Mar 2022 19:29:07 +0000 (19:29 +0000)]
kernel: generic: improve FIT partition parser
* only map filesystems configured in 'loadables'
* allow mapping more than one filesystem (e.g. customization/branding
or localization in addition to rootfs)
* small cleaning here and there
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Eneas U de Queiroz [Tue, 22 Mar 2022 17:03:30 +0000 (14:03 -0300)]
openssl: move engine.mk to INCLUDE_DIR
engine.mk is supposed to be included by engine packages, but it will not
be present in the SDK in the same place as in the main repository.
Move it to include/openssl-engine.mk to avoid this.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Hans Dedecker [Tue, 22 Mar 2022 21:00:24 +0000 (22:00 +0100)]
odhcpd: update to git HEAD
860ca90 odhcpd: Support for Option NTP and SNTP
83e14f4 router: advertise removed addresses as invalid in 3 consecutive RAs
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Felix Fietkau [Tue, 22 Mar 2022 09:28:09 +0000 (10:28 +0100)]
qosify: update to the latest version
57c7817f91c2 qosify: fix dscp values of ubus-added dns host entries
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rui Salvaterra [Wed, 9 Dec 2020 16:11:40 +0000 (16:11 +0000)]
kmod-lzo: include the lzo-rle kmod in the package
Albeit a separate crypto module, lzo-rle uses the same kernel library as lzo.
Crypto API users (zram, for example) expect both lzo and lzo-rle to be
available, so let's include lzo-rle (about 5.5 kiB) in the lib-lzo package.
Based on e9hack's original patch: https://patchwork.ozlabs.org/project/openwrt/patch/
541cbfbd-76f2-59b3-a867-
47b6f0fc7da9@gmail.com/
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Daniel Golle [Mon, 21 Mar 2022 23:31:38 +0000 (23:31 +0000)]
kernel: generic: use chosen bootconf in FIT partition parser
If the selected boot configuration is stored by U-Boot in '/chosen'
node as 'bootconf' attribute, use that configuration to resolve the
block device used as rootfs. Fall back to use the default configuration
in case 'bootconf' is not present.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Mon, 21 Mar 2022 23:30:10 +0000 (23:30 +0000)]
uboot-mediatek: add patch to allow accessing bootconf from Linux
Store selected boot configuration in '/chosen' node in device tree, so
it can be accessed by Linux (and used for fine-tuning the FIT partition
parser).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Petr Štetiar [Tue, 8 Mar 2022 09:41:24 +0000 (10:41 +0100)]
sunxi: cortexa7: fix ethernet link detection on a20-olinuxino-lime2
a20-olinuxino-lime2 is currently having hard time with link detection of
certain 1000Mbit partners due to usage of generic PHY driver, probably
due to following missing workaround introduced in upstream in commit
3aed3e2a143c ("net: phy: micrel: add Asym Pause workaround"):
The Micrel KSZ9031 PHY may fail to establish a link when the Asymmetric
Pause capability is set. This issue is described in a Silicon Errata
(DS80000691D or DS80000692D), which advises to always disable the
capability. This patch implements the workaround by defining a KSZ9031
specific get_feature callback to force the Asymmetric Pause capability
bit to be cleared.
This fixes issues where the link would not come up at boot time, or when
the Asym Pause bit was set later on.
As a20-olinuxino-lime2 has Micrel KSZ9031RNXCC-TR Gigabit PHY since
revision H, so we need to use Micrel PHY driver on those devices.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Daniel Golle [Mon, 21 Mar 2022 20:14:48 +0000 (20:14 +0000)]
uboot-envtools: oxnas: fix wrong eraseblock size for shuttle,kd20
Shuttle KD20 has NAND flash with 0x20000 (128KiB) erase blocks.
Correctly set that in uboot-envtools as well to allow writing to the
bootloader environment using fw_setenv.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Felix Fietkau [Mon, 21 Mar 2022 19:57:41 +0000 (20:57 +0100)]
ramips/mediatek: enable threaded NAPI in the ethernet driver
Improves performance, especially under load
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Mon, 21 Mar 2022 19:26:56 +0000 (20:26 +0100)]
qosify: update to the latest version
391a9fbd5ace dns: fix parsing vlan encapsulated protocol
6aeeddbc91ad interface: extend dns filters to cover vlan tagged traffic as well
1ab53d4ca601 bpf: return TC_ACT_UNSPEC to allow other filters to proceed
ca21e729af23 interface: switch to using clsact for filters
5d158f6b3c15 interface: run ingress bpf filter on main device ingress instead of ifb egress
bdfcb11847ce interface: fix duplicated dns filter line
b97405aa632a Revert "ubus: remove dnsmasq subscriber"
8fbaf39dbc95 interface: rework adding/removing filters, do not delete clsact
d7ba5804eae4 interface: replace open-coded ifb-dns string with QOSIFY_DNS_IFNAME
91cf440db9e2 loader: fix use of deprecated functions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Marek Behún [Mon, 21 Mar 2022 16:35:27 +0000 (17:35 +0100)]
kernel: Fix patch header
Remove "a" character from the first line of patch
738-v5.14-01-net-dsa-qca8k-fix-an-endian-bug-in-qca8k-get-ethtool.patch
Otherwise `git am` fails to apply this patch which is annoying when
trying to do some development / rebasing.
Signed-off-by: Marek Behún <kabel@kernel.org>
Robert Marko [Mon, 21 Mar 2022 11:39:54 +0000 (12:39 +0100)]
uboot-mvebu: backport patch to fix eMMC
v2022.01 has a regression that broke eMMC usage on most if not all Armada
SoC-s, thus breaking boards like uDPU which use eMMC for storage.
Fix it by backporting a recent upstream patch.
Fixes: 782d4c8306c8 ("uboot-mvebu: update to version 2022.01")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Robert Marko [Mon, 21 Mar 2022 10:47:28 +0000 (11:47 +0100)]
mvebu: udpu: include LM75 kmod by default
uDPU has 2 LM75 compatible temperature sensors, so include the driver for
them by default in order to utilize them.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Robert Marko [Mon, 21 Mar 2022 10:47:27 +0000 (11:47 +0100)]
mvebu: udpu: fix initramfs booting
uDPU provides a FIT based initramfs, but currently gets stuck after U-boot
starts the kernel at "Starting kernel..".
It is due to the load address being too low, so increase it in order to get
the initramfs booting again.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Jan Hoffmann [Sun, 13 Mar 2022 21:14:38 +0000 (22:14 +0100)]
ltq-vdsl-mei: add locking to interrupt handler
Some users noticed repeated resyncs at random intervals, which go away
when the MEI driver is configured to use polling instead of interrupts.
Debugging shows that this seems to be caused by concurrent calls to
MEI_ReadMailbox (in the interrupt handler) and MEI_WriteMailbox. This
appears to be mostly triggered when there is an interrupt for vectoring
error reports.
In polling mode, calls to MEI_ReadMailbox are protected by the same
semaphore as is used in MEI_WriteMailbox. When interrupts are used,
MEI_WriteMailbox appears to rely on MEI_DisableDeviceInt and
MEI_EnableDeviceInt to provide mutual exclusion with the interrupt
handler. These functions mask/unmask interrupts, and there is an
additional check of the mask in the interrupt handler itself. However,
this is not sufficient on systems with SMP, as the interrupt handler
may be running in parallel, and could already be past the interrupt
mask check at this point.
This adds a lock to the interrupt handler, and also acquires this lock
in MEI_DisableDeviceInt. This should make sure that after a call to
MEI_DisableDeviceInt the interrupt is masked, and the interrupt handler
is either not running, has alread finished its work, or is still before
the interrupt mask check, and is thus going to detect the change.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Jan Hoffmann [Sun, 13 Mar 2022 21:14:37 +0000 (22:14 +0100)]
ltq-vdsl-app: set MAC address for vectoring error reports
This tells the modem about the WAN MAC address, which is used as source
address for vectoring error reports that are generated by the firmware.
It needs to be set early, as the MEI driver only actually writes the
value to the modem when is in reset state (i.e. the firmware has been
loaded, but connection has not started yet).
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Jan Hoffmann [Sun, 13 Mar 2022 21:14:36 +0000 (22:14 +0100)]
ltq-vdsl-mei: enable vectoring error sample callback
This re-enables the vectoring error sample callback and adds a
dependency to the corresponding driver.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Jan Hoffmann [Sun, 13 Mar 2022 21:14:35 +0000 (22:14 +0100)]
ltq-vectoring: add driver
In order to calculate the required pre-distortion for downstream
vectoring, the vectoring control entity (VCE) at the carrier office
needs error samples from the modem. On Lantiq VR9 modems, error reports
are generated by the firmware, but need to be multiplexed into the data
stream by the driver on the main processor when L2 encapsulation is
selected by the VCE.
This driver provides the necessary callback function, which is called by
the MEI driver after receiving an error report from the firmware.
Originally, it is part of the Lantiq PPA driver, but after a few changes
it also works with the PTM driver used in OpenWrt. The direct call to
ndo_start_xmit needs to be replaced, as the PTM driver relies on locks
from the kernel. Instead dev_queue_xmit is used, which is called from a
work queue, as it is not safe to call from an interrupt handler.
Additional changes include fixes to support recent kernel versions and
a change of the used interface from ptm0 to dsl0.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Daniel Golle [Mon, 21 Mar 2022 01:16:48 +0000 (01:16 +0000)]
kernel: delete Linux 5.4 config and patches
As the upcoming release will be based on Linux 5.10 only, remove all
kernel configuration as well as patches for Linux 5.4.
There were no targets still actively using Linux 5.4.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Richard Huynh [Wed, 1 Dec 2021 01:27:39 +0000 (12:27 +1100)]
mediatek: Add support for Xiaomi Redmi Router AX6S
Also known as the "Xiaomi Router AX3200" in western markets,
but only the AX6S is widely installation-capable at this time.
SoC: MediaTek MT7622B
RAM: DDR3 256 MiB (ESMT M15T2G16128A)
Flash: SPI-NAND 128 MiB (ESMT F50L1G41LB or Gigadevice GD5F1GQ5xExxG)
WLAN: 2.4/5 GHz 4T4R
2.4 GHz: MediaTek MT7622B
5 GHz: MediaTek MT7915E
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531B
LEDs/Keys: 2/2 (Internet + System LED, Mesh button + Reset pin)
UART: Marked J1 on board VCC RX GND TX, beginning from "1". 3.3v, 115200n8
Power: 12 VDC, 1.5 A
Notes:
U-Boot passes through the ethaddr from uboot-env partition,
but also has been known to reset it to a generic mac address
hardcoded in the bootloader.
However, bdata is also populated with the ethernet mac addresses,
but is also typically never written to. Thus this is used instead.
Installation:
1. Flash stock Xiaomi "closed beta" image labelled
'miwifi_rb03_firmware_stable_1.2.7_closedbeta.bin'.
(MD5:
5eedf1632ac97bb5a6bb072c08603ed7)
2. Calculate telnet password from serial number and login
3. Execute commands to prepare device
nvram set ssh_en=1
nvram set uart_en=1
nvram set boot_wait=on
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
4. Download and flash image
On computer:
python -m http.server
On router:
cd /tmp
wget http://<IP>:8000/factory.bin
mtd -r write factory.bin firmware
Device should reboot at this point.
Reverting to stock:
Stock Xiaomi recovery tftp that accepts their signed images,
with default ips of 192.168.31.1 + 192.168.31.100.
Stock image should be renamed to tftp server ip in hex (Eg.
C0A81F64.img)
Triggered by holding reset pin on powerup.
A simple implementation of this would be via dnsmasq's
dhcp-boot option or using the vendor's (Windows only)
recovery tool available on their website.
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
Richard Huynh [Mon, 27 Dec 2021 02:07:29 +0000 (13:07 +1100)]
mediatek: Add GD5F1GQ5xExxG to mtk-snand
Some units of the Xiaomi Redmi Router AX6S/Xiaomi Router AX3200 contain this part.
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
Nicholas Smith [Fri, 11 Mar 2022 03:54:07 +0000 (13:54 +1000)]
ipq40xx: add support for Telco X1 Pro
Telco X1 Pro is a Cat12 LTE-A Pro modem router.
Vendor firmware is based on a recent version of OpenWrt.
Flashing is possible via CLI using sysupgrade -F -n
The serial headers allow bootloader and console access
Serial setting: 115200 8N1
Brief Specifications:
IPQ4019 SoC
32MB flash
512MB RAM
4x gigabit LAN
1x gigabit WAN
Dual-band Wave-2 wifi
2x SMA LTE antenna connectors
2x RP-SMA wifi antennas
1x USB 2.0 port
1x Reset button
Serial headers installed
1x Nano SIM tray
1x Quectel EM-12G LTE-A Pro modem
1x M.2 slot attached to USB 3.0
1x internal micro SD card slot
Signed-off-by: Nicholas Smith <nicholas@nbembedded.com>
Igor Nazarov [Wed, 16 Mar 2022 21:51:35 +0000 (00:51 +0300)]
ramips: add support for D-Link DIR-878 R1
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 128 MB (DDR3)
- Flash: 16 MB (SPI NOR)
- WiFi: MT7615N (2.4GHz) and MT7615N (5Ghz)
- Switch: 1 WAN, 4 LAN (Gigabit)
- Buttons: Reset, WiFi Toggle, WPS
- LEDs: Power, Internet, WiFi 2.4G WiFi 5G
The R1 revision is identical to the A1 revision except
- No Config2 Parition, therefore
- factory partition resized to 64k from 128K
- Firmware partition offset is 0x50000 not 0x60000
- Firmware partitions size increased by 64K
- Firmware partition type is "denx,uimage", not "sge,uimage"
- Padding of image creation "uimage-padhdr 96" removed
Installation:
Update to the last D-Link firmware through web-ui before OpenWRT
installation then follow the instructions to patch your device using
D-Link FailsafeUI.
- D-Link FailsafeUI:
Power down the router, press and hold the reset button, then
re-plug it. Keep the reset button pressed until the internet LED stops
flashing, then jack into any lan port and manually assign a static IP
address in 192.168.0.0/24 other than 192.168.0.1 (e.g. 192.168.0.2)
and go to http://192.168.0.1
Flash with the factory image.
Signed-off-by: Igor Nazarov <tigron.dev@gmail.com>
John Audia [Sat, 19 Mar 2022 16:16:47 +0000 (12:16 -0400)]
kernel: bump 5.10 to 5.10.107
All patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200
Signed-off-by: John Audia <graysky@archlinux.us>
Huangbin Zhan [Mon, 15 Nov 2021 14:03:45 +0000 (22:03 +0800)]
ncurses: update to 6.3
release notes: https://invisible-island.net/ncurses/announce-6.3.html
Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
Mikhail Zhilkin [Wed, 5 Jan 2022 13:11:56 +0000 (13:11 +0000)]
ramips: add support for Beeline SmartBox Flash
Beeline SmartBox Flash is a wireless AC1300 (WiFi 5) router manufactured
by Arcadyan company.
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 256 MiB, Winbond W632GU6NB
Flash: 128 MiB (NAND), Winbond W29N01HVSINF
Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2
Wireless 5 GHz (MT7615DN): a/n/ac, 2x2
Ethernet: 3xGbE (WAN, LAN1, LAN2)
USB ports: 1xUSB3.0
Button: 1 (Reset/WPS)
LEDs: 1 RGB LED
Power: 12 VDC, 1.5 A
Connector type: Barrel
Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2)
OEM: Arcadyan WE42022
Installation
------------
1. Place *factory.trx on any web server (192.168.1.2 in this example)
2. Connect to the router using telnet shell (no password required)
3. Save MAC adresses to U-Boot environment:
uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \
awk '{print $5}')
uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \
awk '{print $5}')
uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \
awk '{print $5}')
uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \
awk '{print $5}')
4. Ensure that MACs were saved correctly:
uboot_env --get --name eth2macaddr
uboot_env --get --name eth3macaddr
uboot_env --get --name ra0macaddr
uboot_env --get --name rax0macaddr
5. Download and write the OpenWrt images:
cd /tmp
wget http://192.168.1.2/factory.trx
mtd_write erase /dev/mtd4
mtd_write write factory.trx /dev/mtd4
6. Set 1st boot partition and reboot:
uboot_env --set --name bootpartition --value 0
reboot
Back to Stock
-------------
1. Run in the OpenWrt shell:
fw_setenv bootpartition 1
reboot
2. Optional step. Upgrade the stock firmware with any version to
overwrite the OpenWrt in Slot 1.
MAC addresses
-------------
+-----------+-------------------+----------------+
| Interface | MAC | Source |
+-----------+-------------------+----------------+
| label | 30:xx:xx:51:xx:09 | No MACs was |
| LAN | 30:xx:xx:51:xx:09 | found on Flash |
| WAN | 30:xx:xx:51:xx:06 | [1] |
| WLAN_2g | 30:xx:xx:51:xx:07 | |
| WLAN_5g | 32:xx:xx:41:xx:07 | |
+-----------+-------------------+----------------+
[1]:
a. Label wasb't found neither in factory nor in other places.
b. MAC addresses are stored in encrypted partition "glbcfg". Encryption
key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack
with saving of the MACs to u-boot-env during the installation was
applied.
c. Default Ralink ethernet MAC address (00:0C:43:28:80:36) was found in
"Factory" 0xfff0. It's the same for all Smartbox Flash devices. OEM
firmware also uses this MAC when initialazes ethernet driver. In
OpenWrt we use it only as internal GMAC (eth0), all other MACs are
unique. Therefore, there is no any barriers to the operation of several
Smartbox Flash devices even within the same broadcast domain.
Stock firmware image format
---------------------------
+--------------+---------------+----------------------------------------+
| Offset | 1.0.15 | Description |
+==============+===============+========================================+
| 0x0 | 5d 43 6f 74 | TRX magic "]Cot" |
+--------------+---------------+----------------------------------------+
| 0x4 | 00 70 ff 00 | Length (reverse) |
+--------------+---------------+----------------------------------------+
| | | htonl(~crc) from 0xc ("flag_version") |
| 0x8 | 72 b3 93 16 | to "Length" |
+--------------+---------------+----------------------------------------+
| 0xc | 00 00 01 00 | Flags |
+--------------+---------------+----------------------------------------+
| | | Offset (reverse) of Kernel partition |
| 0x10 | 1c 00 00 00 | from the start of the header |
+--------------+---------------+----------------------------------------+
| | | Offset (reverse) of RootFS partition |
| 0x14 | 00 00 42 00 | from the start of the header |
+--------------+---------------+----------------------------------------+
| 0x18 | 00 00 00 00 | Zeroes |
+--------------+---------------+----------------------------------------+
| 0x1c | 27 05 19 56 … | Kernel data + zero padding |
+--------------+---------------+----------------------------------------+
| | | RootFS data (starting with "hsqs") + |
| 0x420000 | 68 73 71 73 … | zero padding to "Length" |
+--------------+---------------+----------------------------------------+
| | | Some signature data (format is |
| | | unknown). Necessary for the fw |
| "Lenght" | 00 00 00 00 … | update via oem fw web interface. |
+--------------+---------------+----------------------------------------+
| "Lenght" + | | TRX magic "HDR0". U-Boot is |
| 0x10c | 48 44 52 30 | checking it at every boot. |
+--------------+---------------+----------------------------------------+
| | | 1.00: |
| | | Zero padding to ("Lenght" + 0x23000) |
| | | 1.0.12: |
| | | Zero padding to ("Lenght" + 0x2a000) |
| "Lenght" + | | 1.0.13, 1.0.15, 1.0.16: |
| 0x110 | 00 00 00 00 | Zero padding to ("Lenght" + 0x10000) |
+--------------+---------------+----------------------------------------+
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Florian Eckert [Wed, 22 Dec 2021 07:59:43 +0000 (08:59 +0100)]
base-files: add wrapper for procd service list command
A service managed by procd does have a json object with usefull information.
This information could by dumped with the following command.
ubus call service list "{ 'verbose':true, 'name': '<service-name>)'". }"
This line is long and complicated to enter. This commit adds a wrapper
call to the procd service section tool to simplify the input and get the
output faster.
We could now enter the command /etc/initd/<service> info to get the info
faster.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Florian Eckert [Tue, 30 Nov 2021 15:01:14 +0000 (16:01 +0100)]
procd: move service command to procd
The service command belongs to the procd and does not belong in the
shinit. In the course of the move, the script was also checked with
shellcheck and cleaned up.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
John Audia [Wed, 16 Mar 2022 20:06:23 +0000 (16:06 -0400)]
kernel: bump 5.10 to 5.10.106
All patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200
Signed-off-by: John Audia <graysky@archlinux.us>
John Audia [Fri, 11 Mar 2022 12:15:14 +0000 (07:15 -0500)]
kernel: bump 5.10 to 5.10.105
Updated default config with new sym (CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY=y).
Manually rebased:
generic/hack-5.10/220-arm-gc_sections.patch
All other patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200
Signed-off-by: John Audia <graysky@archlinux.us>
Etienne Champetier [Fri, 18 Mar 2022 00:05:28 +0000 (20:05 -0400)]
iptables: bump PKG_RELEASE
Following {arp,eb}tables-nft addition, bump PKG_RELEASE
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
Etienne Champetier [Tue, 1 Mar 2022 04:14:48 +0000 (23:14 -0500)]
iptables: add {arp,eb}tables-nft
Add a patch to add some missing init_extensions{a,b}() calls
Package lib{arp,eb}t_*.so
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
Etienne Champetier [Tue, 1 Mar 2022 04:32:53 +0000 (23:32 -0500)]
iptables: add xtables-nft package
This allows to install ip6tables-nft without iptables-nft
This prepare the addition of {arp,eb}tables-nft
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
Etienne Champetier [Tue, 1 Mar 2022 04:24:11 +0000 (23:24 -0500)]
iptables: add xtables-legacy package
This allows to install ip6tables-legacy without iptables-legacy
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
Etienne Champetier [Tue, 1 Mar 2022 04:00:22 +0000 (23:00 -0500)]
ebtables: rename to ebtables-legacy
This prepare the introduction of ebtables-nft.
Add PROVIDES so dependencies are not broken,
use ALTERNATIVES.
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
Etienne Champetier [Tue, 1 Mar 2022 03:37:41 +0000 (22:37 -0500)]
arptables: rename package to arptables-legacy
This prepare the introduction of arptables-nft.
Add PROVIDES so dependencies are not broken,
use ALTERNATIVES.
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
Rosen Penev [Fri, 26 Mar 2021 10:09:34 +0000 (03:09 -0700)]
quilt.mk: fix typo in the Host section
HOST_PATCH_DIR is used for host patches, not PATCH_DIR.
Fixes refreshing patches with a custom HOST_PATCH_DIR.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Josef Schlehofer [Wed, 16 Mar 2022 12:14:57 +0000 (13:14 +0100)]
cypress-firmware: update it to version 5.4.18-2021_0812
- Binary files were renamed to cyfmac from brcmfmac, but the files needs
to be on the router with the previous naming
[ 6.656165] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 6.665182] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43455-sdio.bin failed with error -2
[ 6.674928] brcmfmac mmc1:0001:1: Falling back to sysfs fallback for: brcm/brcmfmac43455-sdio.bin
- Cypress were acquired by Infineon Technologies
Thus change the project URL and switch to download files from their
GitHub repository. This is much better than the previous solution, which
requires finding new threads on their community forum about new driver
updates, and it will be necessary to change the URL each time.
Unfortunately, it seems that there is not published changelog, but
according to this forum thread [1], be careful by opening the link from
solution since it contains ending bracket ), it brings fixes for various
security vulnerabilities, which were fixed in 7_45_234.
Fixes:
- FragAttacks
- Kr00k
Also add LICENSE file
Run tested on Seeedstudio router powered by Raspberry Pi 4 CM with
package cypress-firmware-43455-sdio.
Before:
root@OpenWrt:~# dmesg | grep 'Firmware: BCM4345/6'
[ 6.895050] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Mar 23 2020 02:20:01 version 7.45.206 (r725000 CY) FWID 01-
febaba43
After:
root@OpenWrt:~# dmesg | grep 'Firmware: BCM4345/6'
[ 6.829805] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Apr 15 2021 03:03:20 version 7.45.234 (
4ca95bb CY) FWID 01-
996384e2
[1] https://community.infineon.com/t5/Wi-Fi-Bluetooth-for-Linux/Outdated-brcmfmac-firmware-for-Raspberry-Pi-4-in-OpenWrt-21-02-1/m-p/331593#M2269
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Josef Schlehofer [Thu, 17 Mar 2022 17:49:57 +0000 (18:49 +0100)]
bcm27xx: bcm2711: add kmod-usb-net-lan78xx
Some vendors like Seeedstudio in their product [1] with Raspberry Pi
Compute Module 4 uses Microchip LAN7800 (USB 3.0 to Gigabit
Ethernet Bridge) - USB 3.0 extended from PCIe of CM4.
lsusb output:
```
Bus 002 Device 002: ID 0424:7800 Microchip LAN7800
```
Raspberry Pi 4 and even Compute Module 4 has many resources available
and for just one kernel module it is not necessary to add additional specific CM4 profiles.
Let's include it by default, so the both Ethernet ports will be usable
to have better user-experience. Because previous generation of Raspberry
Pi included LAN7800 Gigabit Ethernet by default and it is enabled there
[2] in kernel without additional kernel module, which was added recently [3].
After this commit in dmesg can be found this:
```
root@OpenWrt:~# dmesg | grep lan
[ 7.038889] lan78xx 2-3:1.0 (unnamed net_device) (uninitialized): int urb period 64
[ 7.090484] usbcore: registered new interface driver lan78xx
```
Tested and works with sysupgrade image.
[1] https://www.seeedstudio.com/Dual-GbE-Carrier-Board-with-4GB-RAM-32GB-eMMC-RPi-CM4-Case-p-5029.html
[2] https://github.com/openwrt/openwrt/blob/
32c74552b2310531af593ee0f859a3935a3a7cbd/target/linux/bcm27xx/bcm2709/config-5.4#L437
[3] https://github.com/openwrt/openwrt/commit/
31647d8be8c60bfb6690c87c739b8abe6dc03950
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Josef Schlehofer [Thu, 17 Mar 2022 23:07:50 +0000 (00:07 +0100)]
iwinfo: update to latest Git head
Changelog:
90bfbb9 devices: Add Cypress CYW43455
234075b devices: fix AMD RZ608 format
0e2a318 devices: add AMD RZ608 device-id
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Felix Fietkau [Sat, 19 Mar 2022 12:28:41 +0000 (13:28 +0100)]
bpftools: fix library path on 64 bit systems
drop the use of LIB_SUFFIX
Fixes: 00cbf6f6ab1d ("bpftools: update to standalone bpftools + libbpf, use the latest version")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Tue, 15 Mar 2022 13:33:59 +0000 (14:33 +0100)]
bpftools: update to standalone bpftools + libbpf, use the latest version
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Fri, 18 Mar 2022 13:36:57 +0000 (14:36 +0100)]
mac80211: backport MBSSID support
Required for an upcoming mt76 update
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Stijn Tintel [Mon, 14 Mar 2022 19:56:55 +0000 (21:56 +0200)]
kernel: enable SERIAL_8250_16550A_VARIANTS
Kernel 5.6 introduced a new config symbol SERIAL_8250_16550A_VARIANTS.
In kernel 5.8, this symbol was changed to default to on on !x86, as some
embedded devices still use 16650A variants. Let's play safe here and
enable this symbol in the generic config, to avoid others from running
into this problem and having to spend several hours trying to bisect
this problem. While we could disable the symbol in the x86 target
configs, a 20ms boot time reduction really isn't worth the time wasted
on bisecting this issue.
Matt discovered this problem while working on adding support for the
WatchGuard Firebox M200 to the qoriq target, where it caused some
characters to be missing on the console output.
Reported-by: Matt Fawcett <mattytap@icloud.com>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Rui Salvaterra <rsalvaterra@gmail.com>
Pascal Coudurier [Tue, 25 Jan 2022 20:18:28 +0000 (21:18 +0100)]
ath79: improve support for GL.iNet GL-XE300
- fix eth0 eth1 sharing same mac so it conforms to the behavior stated
in the original commit and the way it is in vendor firmware :
WAN is label, LAN is label +1 and WLAN is label +2
- add default leds config
- add default network config
Signed-off-by: Pascal Coudurier <coudu@wanadoo.fr>
Petr Štetiar [Thu, 17 Mar 2022 06:53:55 +0000 (07:53 +0100)]
mpc85xx: fix missing kernel config symbol and DTS whitespace issue
Buildbot has reported following issue while crunching mpc85xx/p1010
subtarget:
Extreme Networks WS-AP3825i (WS_AP3825I) [N/y/?] (NEW)
Fix it by disabling that config symbol in target kernel config and while
at it fix DTS whitespace issue.
Fixes: 7e614820a892 ("mpc85xx: add support for Extreme Networks WS-AP3825i")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Jan Hoffmann [Wed, 16 Mar 2022 17:24:23 +0000 (18:24 +0100)]
lantiq: fritz7362sl: add partition subnode for SPI flash
Without a partition subnode ofpart_core still parses direct subnodes as
partitions, but it ignores nodes with a compatible property. Due to
this, the switch to nvmem-cells made the urlader partition inaccessible.
As a result, the wireless network was broken, as the calibration data
is read from that partition by a script.
Fixes: #8983
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Martin Blumenstingl [Tue, 15 Mar 2022 21:53:04 +0000 (22:53 +0100)]
lantiq: fritz7362sl: fix SPI flash node reg property
The &spi node has #address-cells = <1> and #size-cells = <0>. Drop the
extra 0 in the reg property from the SPI flash node to ensure it's
number of cells matches the definition in the parent node. This also
makes the reg property for the SPI flash node consistent with all other
VR9 boards.
Fixes: eae6cac6a30b ("lantiq: add support for AVM FRITZ!Box 7362 SL")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Christian Lamparter [Wed, 16 Mar 2022 16:34:24 +0000 (17:34 +0100)]
ipq806x: fix TP-Link Archer VR2600v bootlooping
Timo Schroeder reported:
"The TP-Link Archer VR2600v is stuck in a boot loop on written
snapshot image. It's able to boot using the snapshot uimage
though, but there ath10k firmware can't be found.
21.02.2 release version doesn't have either problem."
The VR2600v has a 512 byte header at the beginning of the
firmware that needs to be accounted for.
Fixes: f6a01d7f5c3d ("ipq806x: convert TP-Link Archer VR2600v to denx,uimage")
Reported-by: Timo Schroeder <der.timosch@gmail.com>
References: <https://github.com/openwrt/openwrt/issues/9467>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Martin Kennedy [Sun, 28 Nov 2021 01:59:18 +0000 (20:59 -0500)]
mpc85xx: add support for Extreme Networks WS-AP3825i
Hardware:
- SoC: Freescale P1020
- CPU: 2x e500v2 @ 800MHz
- Flash: 64MiB NOR (1x Intel JS28F512)
- Memory: 256MiB (2x ProMOS DDR3 V73CAG01168RBJ-I9H 1Gb)
- WiFi1: 2.4+5GHz abgn 3x3 (Atheros AR9590)
- Wifi2: 5GHz an+ac 3x3 (Qualcomm Atheros QCA9890)
- ETH: 2x PoE Gigabit Ethernet (2x Atheros AR8035)
- Power: 12V (center-positive barrel) or 48V PoE (active or passive)
- Serial: Cisco-compatible RJ45 next to 12V power socket (115200 baud)
- LED Driver: TI LV164A
- LEDs: (not functioning)
- 2x Power (Green + Orange)
- 4x ETH (ETH1 + ETH2) x (Green + Orange)
- 2x WiFi (WiFi2 + WiFi1)
Installation:
1. Grab the OpenWrt initramfs <openwrt-initramfs-bin>, e.g.
openwrt-mpc85xx-p1020-extreme-networks_ws-ap3825i-initramfs-kernel.bin.
Place it in the root directory of a DHCP+TFTP server, e.g. OpenWrt
`dnsmasq` with configuration `dhcp.server.enable_tftp='1'`.
2. Connect to the serial port and boot the AP with options
e.g. 115200,N,8. Stop autoboot in U-Boot by pressing Enter after
'Scanning JFFS2 FS:' begins, then waiting for the prompt to be
interrupted. Credentials are identical to the one in the APs
interface. By default it is admin / new2day: if these do not work,
follow the OEM's reset procedure using the reset button.
3. Set the bootcmd so the AP can boot OpenWrt by executing:
```uboot
setenv boot_openwrt "cp.b 0xEC000000 0x2000000 0x2000000; interrupts off; bootm start 0x2000000; bootm loados; fdt resize; fdt boardsetup; fdt chosen; bootm prep; bootm go;"
setenv bootcmd "run boot_openwrt"
saveenv
```
If you plan on going back to the vendor firmware - the bootcmd for it
is stored in the boot_flash variable.
4. Load the initramfs image to RAM and boot by executing
```uboot
setenv ipaddr <ipv4 client address>;
setenv serverip <tftp server address>;
tftpboot 0x2000000 <openwrt-initramfs-bin>;
interrupts off;
bootm start 0x2000000;
bootm loados;
fdt resize;
fdt boardsetup;
fdt chosen;
bootm prep;
bootm go;
```
5. Make a backup of the "firmware" partition if you ever wish to go back
to the vendor firmware.
6. Upload the OpenWrt sysupgrade image via SCP to the devices /tmp
folder.
7. Flash OpenWrt using sysupgrade.
```ash
sysupgrade /tmp/<openwrt-sysupgrade-bin>
```
Notes:
- We must step through the `bootm` process manually to avoid fdt
relocation. To explain: the stock U-boot (and stock Linux) are configured
with a very large CONFIG_SYS_BOOTMAPSZ (and the device's stock Linux
kernel is configured to be able to handle it). The U-boot version
predates the check for the `fdt_high` variable, meaning that upon fdt
relocation, the fdt can (and will) be moved to a very high address; the
default appears to be 0x9ffa000. This address is so high that when the
Linux kernel starts reading the fdt at the beginning of the boot process,
it encounters a memory access exception and panics[5]. While it is
possible to reduce the highest address the fdt will be relocated to by
setting `bootm_size`, this also has the side effect of limiting the
amount of RAM the kernel can use[3].
- Because it is not relocated, the flattened device tree needs to be
padded in the build process to guarantee that `fdt resize` has
enough space.
- The primary ethernet MAC address is stored (and set) in U-boot; they are
shimmed into the device tree by 'fdt boardsetup' through the
'local-mac-address' property of the respective ethernet node, so OpenWrt
does not need to set this at runtime. Note that U-boot indexes the
ethernet nodes by alias, which is why the device tree explicitly aliases
ethernet1 to enet2.
- LEDs do not function under OpenWrt. Each of 8 LEDs is connected to an
output of a TI LV164A shift register, which is wired to GPIO lines and
operates through bit-banged SPI. Unfortunately, I am unable to get the
spi-gpio driver to recognize the `led_spi` device tree node at all, as
confirmed by patching in printk messages demonstrating
spi-gpio.c::spi_gpio_probe never runs. It is possible to manually
articulate the shift register by exporting the GPIO lines and stepping
their values through the sysfs.
- Though they do not function under OpenWrt, I have left the pinout details
of the LEDs and shift register in the device tree to represent real
hardware.
- An archive of the u-boot and Linux source for the AP3825i (which is one
device of a range of devices code-named 'CHANTRY') be found here[1].
- The device has an identical case to both the Enterasys WS-AP3725i and
Adtran BSAP-2030[2] (and potentially other Adtran BSAPs). Given that
there is no FCC ID for the board itself (only its WLAN modules), it's
likely these are generic boards, and even that the WS-AP3725i is
identical, with only a change in WLAN card. I have ordered one to confirm
this.
- For additional information: the process of porting the board is
documented in an OpenWrt forum thread[4].
[1]: magnet:?xt=urn:btih:
f5306a5dfd06d42319e4554565429f84dde96bbc
[2]: https://forum.openwrt.org/t/support-for-adtran-bluesocket-bsap-2030/48538
[3]: https://forum.openwrt.org/t/adding-openwrt-support-for-ws-ap3825i/101168/29
[4]: https://forum.openwrt.org/t/adding-openwrt-support-for-ws-ap3825i/101168
[5]: https://forum.openwrt.org/t/adding-openwrt-support-for-ws-ap3825i/101168/26
Tested-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
Rosen Penev [Thu, 10 Mar 2022 06:31:14 +0000 (22:31 -0800)]
argp-standalone: fix compilation with Alpine Linux
This package is a C89 one. Add the proper CFLAG to fix compilation.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Brian Norris [Sun, 13 Mar 2022 06:04:30 +0000 (22:04 -0800)]
base-files: Align rootfs_data upgrades to 64KiB on eMMC
Rootfs overlays get created at a ROOTDEV_OVERLAY_ALIGN (64KiB)
alignment after the rootfs, but emmc_do_upgrade() is assuming
it comes at the very next 512-byte sector.
Suggested-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
(move spaces around, mention fstools' libtoolfs)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Martin Schiller [Wed, 16 Mar 2022 14:04:56 +0000 (15:04 +0100)]
openssl: bump to 1.1.1n
This is a bugfix release. Changelog:
*) Fixed a bug in the BN_mod_sqrt() function that can cause it to loop
forever for non-prime moduli. (CVE-2022-0778)
*) Add ciphersuites based on DHE_PSK (RFC 4279) and ECDHE_PSK
(RFC 5489) to the list of ciphersuites providing Perfect Forward
Secrecy as required by SECLEVEL >= 3.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Rodolphe de Saint Léger [Wed, 16 Mar 2022 09:19:30 +0000 (10:19 +0100)]
ramips: add support for Netgear WN3100RPv2
This patch adds support for the Netgear WN3100RPv2
http://www.netgear.com/support/product/wn3100rpv2.aspx
Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Stock firmware based on OpenWRT Kamikaze
Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577
This device seems to be same hardware as a WN3000RPv3
Flash instructions:
- Use the Netgear WebUI to upgrade to OpenWRT using the factory image
(see note below),
- Use the sysupgrade image for upgrading versions from OpenWRT,
- TFTP recovery procedure can be used to flash the factory image
(preferred method).
Note:
- The WebUI may not reboot automatically, wait at least 5 minutes before
powercycling the device
Flashing using TFTP:
- Set you IP address to 192.168.1.10/24 (no gateway)
- Connect your machine to the Ethernet port
- Power off the device and wait for 10 seconds,
- Hold the reset button and power on the device (do not release reset),
- Hold the reset button until the green light is flashing (Approx. 15s)
- launch tftp, set mode to binary and connect to 192.168.1.1
- put the factory firmware image
- All leds will switch off (like a power off), this is normal
- Wait for the device to reboot in the new OpenWRT image (max 5 mins)
- The first boot will take longer than usual.
- After boot, the Device IP on the ethernet port is 192.168.1.1
Signed-off-by: Rodolphe de Saint Léger <rdesaintleger@gmail.com>
[drop unneeded includes in dts, wrap commit message]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Wed, 16 Mar 2022 14:10:45 +0000 (23:10 +0900)]
Revert "ramips: add support for Netgear WN3000RPv3"
This reverts commit
7bc20cb6143e089fae6ad4b173fc42b55bdbecfe.
It adds support for Netgear WN3100RPv2, but the commit title is wrong.
It will be re-added with the correct title.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Rodolphe de Saint Léger [Wed, 16 Mar 2022 09:19:30 +0000 (10:19 +0100)]
ramips: add support for Netgear WN3000RPv3
This patch adds support for the Netgear WN3100RPv2
http://www.netgear.com/support/product/wn3100rpv2.aspx
Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Stock firmware based on OpenWRT Kamikaze
Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577
This device seems to be same hardware as a WN3000RPv3
Flash instructions:
- Use the Netgear WebUI to upgrade to OpenWRT using the factory image
(see note below),
- Use the sysupgrade image for upgrading versions from OpenWRT,
- TFTP recovery procedure can be used to flash the factory image
(preferred method).
Note:
- The WebUI may not reboot automatically, wait at least 5 minutes before
powercycling the device
Flashing using TFTP:
- Set you IP address to 192.168.1.10/24 (no gateway)
- Connect your machine to the Ethernet port
- Power off the device and wait for 10 seconds,
- Hold the reset button and power on the device (do not release reset),
- Hold the reset button until the green light is flashing (Approx. 15s)
- launch tftp, set mode to binary and connect to 192.168.1.1
- put the factory firmware image
- All leds will switch off (like a power off), this is normal
- Wait for the device to reboot in the new OpenWRT image (max 5 mins)
- The first boot will take longer than usual.
- After boot, the Device IP on the ethernet port is 192.168.1.1
Signed-off-by: Rodolphe de Saint Léger <rdesaintleger@gmail.com>
[drop unneeded includes in dts, wrap commit message]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Pawel Dembicki [Thu, 17 Feb 2022 23:23:45 +0000 (00:23 +0100)]
ramips: mt7620: Add support for D-Link DWR-961 A1
The DWR-961 A1 Wireless Router is based on the MT7620A SoC.
It's a merge of two Amit boards: DWR-960 with ethernet part
of Lava LR-25G001.
ROMID it's taken from Telenor branded version and it works with tested
device. Images from D-Link site for this router are from DWR-953 and it
have ROMID DLK6E2424001. I don't know if it's mistake on web-site
or if it's will require different image.
Specification:
- MediaTek MT7620A (580 Mhz)
- 128 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7612 mpcie card)
- 5x 10/100/1000 Mbps Ethernet: 4xLAN and 1xWAN (QCA8337)
- 2x internal, non-detachable antennas (Wifi 2.4G)
- 3x external, detachable antennas (2x LTE, 1x Wifi 5G)
- 1x LTE modem cat 6
- UART (J5) header on PCB (57600 8n1)
- 13x LED, 2x button
- JBOOT bootloader
Installation:
Apply factory image via http web-gui or JBOOT recovery page
How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Stijn Tintel [Tue, 15 Mar 2022 23:25:08 +0000 (01:25 +0200)]
qoriq: enable I2C in target kernel config
The I2C controller used in QorIQ PPC devices requires the mpc-i2c
driver, which is enabled by the I2C_MPC kernel config symbol. Enable
this and its dependencies in the target kernel config, as is done for
the mpc85xx target.
This fixes missing hwmon, rtc and tpm devices on the M300.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Rafał Miłecki [Tue, 15 Mar 2022 17:42:15 +0000 (18:42 +0100)]
bcm4908: include U-Boot DTB files for ASUS GT-AX6000 & Netgear RAX220
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Tue, 15 Mar 2022 17:41:03 +0000 (18:41 +0100)]
uboot-bcm4908: add BCM4912 build
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Tue, 15 Mar 2022 13:30:20 +0000 (14:30 +0100)]
uboot-bcm4908: update to the latest generic
0625aad74d arm: dts: add ASUS GT-AX6000
6fb1cb624d arm: dts: add Netgear RAXE450 / RAXE550
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Tue, 15 Mar 2022 11:40:40 +0000 (12:40 +0100)]
uboot-bcm4908: use "xxd" from staging_dir
This fixes:
bash: xxd: command not found
on hosts without xxd installed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Felix Fietkau [Tue, 15 Mar 2022 09:45:38 +0000 (10:45 +0100)]
mt76: update to the latest version
378b638c70c0 mt76: mt7915: fix unused variable with testmode disabled
4f4309542862 mt76: mt7915: only use u32_get_bits with constant value
de06d828a0bf mt76: mt7921: fix injected MPDU transmission to not use HW A-MSDU
c007ba3ec7a9 mt76: mt7915: simplify conditional
64c74dc93f68 mt76: fix dfs state issue with 160 MHz channels
d3471b0d92c1 mt76: mt7615: honor ret from mt7615_mcu_restart in mt7663u_mcu_init
f4c87b32e0e9 mt76: mt7663u: introduce mt7663u_mcu_power_on routine
82de5987af54 mt76: mt7921: fix up the monitor mode
c501df4086e1 mt76: mt7921: use mt76_hw instead of open coding it
594ee03d5a11 mt76: mt7915: fix DFS no radar detection event
d8d2b383a241 mt76: split single ldpc cap bit into bits
0f336fba20fe mt76: mt7921: make mt7921_init_tx_queues static
00a066ce9914 mt76: mt7921: fix xmit-queue dump for usb and sdio
d6d2479568b2 mt76: mt7921: fix mt7921_queues_acq implementation
d17b74420199 mt76: fix monitor mode crash with sdio driver
c374559eae6f mt76: mt7915: allow beaconing on all chains
b219af63b9ce mt76: connac: add 6 GHz support for wtbl and starec configuration
630384cb3246 mt76: mt7915: add 6 GHz support
28ff1bddc7e8 mt76: mt7915: fix eeprom fields of txpower init values
d4b226cc15e7 mt76: mt7915: add txpower init for 6GHz
31e820d4ce4b mt76: mt7921: get rid of mt7921_wait_for_mcu_init declaration
9fee1faf6028 mt76: mt7915: check for devm_pinctrl_get() failure
31a970940b97 mt76: connac: make read-only array ba_range static const
e49af7036bbc mt76: use le32/16_get_bits() whenever possible
0664d39039c2 mt76: fix invalid rssi report
f16fc9d96105 mt76: mt7915: set band1 TGID field in tx descriptor
67ce2708dcef mt76: mt7915: fix beamforming mib stats
6e899abec818 mt76: mt7915: fix phy cap in mt7915_set_stream_he_txbf_caps()
c6780c85cff2 mt76: mt7915: fix typos in comments
aa6eadc09a83 mt76: usb: add req_type to ___mt76u_rr signature
74a519ab8353 mt76: usb: add req_type to ___mt76u_wr signature
2651d2c66cbd mt76: usb: introduce __mt76u_init utility routine
c03e095eee27 mt76: mt7921: disable runtime pm for usb
41085cdcd7e3 mt76: mt7921: update mt7921_skb_add_usb_sdio_hdr to support usb
e700aba6bae3 mt76: mt7921: move mt7921_usb_sdio_tx_prepare_skb in common mac code
056b7f4ebcc6 mt76: mt7921: move mt7921_usb_sdio_tx_complete_skb in common mac code.
0abf682a3def mt76: mt7921: move mt7921_usb_sdio_tx_status_data in mac common code.
b0c60d5252de mt76: mt7921: add mt7921u driver
053668acdaf8 mt76: mt7921: move mt7921_init_hw in a dedicated work
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Philip Prindeville [Tue, 26 Oct 2021 19:47:17 +0000 (13:47 -0600)]
kernel: include CONFIG_KEXEC_SIG in configs
Seeing failure to build because of missing symbols related to provisioning
CONFIG_KEXEC and signed images. Without this, if you set
CONFIG_KERNEL_KEXEC=y and try to build, target/linux will hang at:
scripts/kconfig/conf --syncconfig Kconfig
...
kexec system call (KEXEC) [Y/n/?] y
kexec file based system call (KEXEC_FILE) [Y/n/?] y
Verify kernel signature during kexec_file_load() syscall (KEXEC_SIG) [N/y/?] (NEW)
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Marek Behún [Mon, 14 Mar 2022 17:31:30 +0000 (18:31 +0100)]
kernel: backport DSA patches fixing null-pointer dereference for 5.10
Backport patches
381a730182f1 ("net: dsa: Move VLAN filtering syncing out of dsa_switch_bridge_leave")
108dc8741c20 ("net: dsa: Avoid cross-chip syncing of VLAN filtering")
from upstream (currently in net-next) to fix null-pointer dereference.
Signed-off-by: Marek Behún <kabel@kernel.org>
Petr Štetiar [Fri, 11 Mar 2022 19:56:02 +0000 (20:56 +0100)]
mac80211: headers: fix lockdep_assert_not_held()
LOCK_STATE_HELD define was omitted during backport of
lockdep_assert_not_held() which leads to build failures of kernels with
CONFIG_LOCKDEP=y:
backports-5.15.8-1/backport-include/linux/lockdep.h:16:47: error: 'LOCK_STATE_HELD' undeclared (first use in this function)
Fix it by adding missing LOCK_STATE_HELD define.
References: PR#9373
Reported-by: Oskari Rauta <oskari.rauta@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Michael Pratt [Wed, 8 Sep 2021 21:00:00 +0000 (17:00 -0400)]
ath79: add support for Araknis AN-700-AP-I-AC
FCC ID: 2AG6R-AN700APIAC
Araknis AN-700-AP-I-AC is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP1750
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- QCA9558 SOC MIPS 74kc, 2.4 GHz WMAC, 3x3
- QCA9880 WLAN PCI card, 5 GHz, 3x3, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM NT5TU32M16
- UART console J10, populated, RX shorted to ground
- 4 antennas 5 dBi, internal omni-directional plates
- 4 LEDs power, 2G, 5G, wps
- 1 button reset
NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide
therefore, the power LED is off for default state
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:xb art 0x0
phy1 2.4G *:xc ---
phy0 5GHz *:xd ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.20.253
username and password 'araknis'
make a new password, login again...
Navigate to 'File Management' page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm
wait about 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
192.168.20.253
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
Method 1: Serial to load Failsafe webpage (above)
Method 2: delete a checksum from uboot-env
this will make uboot load the failsafe image at next boot
because it will fail the checksum verification of the image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait a minute
connect to ethernet and navigate to
192.168.20.253
select OEM firmware image and click upgrade
Method 3: backup mtd partitions before upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs-kernel.bin to '
0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot with serial console
execute `tftpboot` and `bootm 0x81000000`
NOTE: TFTP may not be reliable due to bugged bootloader
set MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software is built using SDKs from Senao
which is based on a heavily modified version
of Openwrt Kamikaze or Altitude Adjustment.
One of the many modifications is sysupgrade being performed by a custom script.
Images are verified through successful unpackaging, correct filenames
and size requirements for both kernel and rootfs files, and that they
start with the correct magic numbers (first 2 bytes) for the respective headers.
Newer Senao software requires more checks but their script
includes a way to skip them.
The OEM upgrade script is at
/etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be less than 1536k
and the OEM upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied at the PHY side,
using the at803x driver `phy-mode` setting through the DTS.
Therefore, the Ethernet Configuration registers for GMAC0
do not need the bits for RGMII delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Michael Pratt [Wed, 17 Mar 2021 05:07:36 +0000 (01:07 -0400)]
ath79: add support for Araknis AN-500-AP-I-AC
FCC ID: 2AG6R-AN500APIAC
Araknis AN-500-AP-I-AC is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP1200
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- QCA9557 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2
- QCA9882 WLAN PCI card 168c:003c, 5 GHz, 2x2, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM NT5TU32M16
- UART console J10, populated, RX shorted to ground
- 4 antennas 5 dBi, internal omni-directional plates
- 4 LEDs power, 2G, 5G, wps
- 1 button reset
NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide
therefore, the power LED is off for default state
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:e1 art 0x0
phy1 2.4G *:e2 ---
phy0 5GHz *:e3 ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.20.253
username and password 'araknis'
make a new password, login again...
Navigate to 'File Management' page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm
wait about 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
192.168.20.253
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
Method 1: Serial to load Failsafe webpage (above)
Method 2: delete a checksum from uboot-env
this will make uboot load the failsafe image at next boot
because it will fail the checksum verification of the image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait a minute
connect to ethernet and navigate to
192.168.20.253
select OEM firmware image and click upgrade
Method 3: backup mtd partitions before upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs-kernel.bin to '
0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot with serial console
execute `tftpboot` and `bootm 0x81000000`
NOTE: TFTP may not be reliable due to bugged bootloader
set MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software is built using SDKs from Senao
which is based on a heavily modified version
of Openwrt Kamikaze or Altitude Adjustment.
One of the many modifications is sysupgrade being performed by a custom script.
Images are verified through successful unpackaging, correct filenames
and size requirements for both kernel and rootfs files, and that they
start with the correct magic numbers (first 2 bytes) for the respective headers.
Newer Senao software requires more checks but their script
includes a way to skip them.
The OEM upgrade script is at
/etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be less than 1536k
and the OEM upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied at the PHY side,
using the at803x driver `phy-mode` setting through the DTS.
Therefore, the Ethernet Configuration registers for GMAC0
do not need the bits for RGMII delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Michael Pratt [Fri, 26 Mar 2021 06:12:26 +0000 (02:12 -0400)]
ath79: add support for Araknis AN-300-AP-I-N
FCC ID: U2M-AN300APIN
Araknis AN-300-AP-I-N is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EWS310AP
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- AR9344 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2
- AR9382 WLAN PCI on-board 168c:0030, 5 GHz, 2x2
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 16 MB FLASH MX25L12845EMI-10G
- 2x 64 MB RAM 1839ZFG V59C1512164QFJ25
- UART console J10, populated, RX shorted to ground
- 4 antennas 5 dBi, internal omni-directional plates
- 4 LEDs power, 2G, 5G, wps
- 1 button reset
NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide
therefore, the power LED is off for default state
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:7d art 0x0
phy1 2.4G *:7e ---
phy0 5GHz *:7f ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
Method 1: Firmware upgrade page:
(if you cannot access the APs webpage)
factory reset with the reset button
connect ethernet to a computer
OEM webpage at 192.168.20.253
username and password 'araknis'
make a new password, login again...
Navigate to 'File Management' page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm
wait about 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
192.168.20.253
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
Method 1: Serial to load Failsafe webpage (above)
Method 2: delete a checksum from uboot-env
this will make uboot load the failsafe image at next boot
because it will fail the checksum verification of the image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait a minute
connect to ethernet and navigate to
192.168.20.253
select OEM firmware image and click upgrade
Method 3: backup mtd partitions before upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs-kernel.bin to '
0101A8C0.img'
make available on TFTP server at 192.168.1.101
power board, interrupt boot with serial console
execute `tftpboot` and `bootm 0x81000000`
NOTE: TFTP may not be reliable due to bugged bootloader
set MTU to 600 and try many times
**Format of OEM firmware image:**
The OEM software is built using SDKs from Senao
which is based on a heavily modified version
of Openwrt Kamikaze or Altitude Adjustment.
One of the many modifications is sysupgrade being performed by a custom script.
Images are verified through successful unpackaging, correct filenames
and size requirements for both kernel and rootfs files, and that they
start with the correct magic numbers (first 2 bytes) for the respective headers.
Newer Senao software requires more checks but their script
includes a way to skip them.
The OEM upgrade script is at
/etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be less than 1536k
and the OEM upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied at the PHY side,
using the at803x driver `phy-mode` setting through the DTS.
Therefore, the Ethernet Configuration registers for GMAC0
do not need the bits for RGMII delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Michael Pratt [Wed, 17 Mar 2021 23:07:46 +0000 (19:07 -0400)]
ath79: improve factory.bin for some Senao devices
Some boards with firmware made with Senao SDK based on Linux 3.3
have the following lines in the OEM upgrade script at
/etc/fwupgrade.sh
local append=""
local CONF_TAR="/tmp/sysupgrade.tgz"
[ -f "$CONF_TAR" ] && append="-j $CONF_TAR"
and
\# check FWINFO filename
[ -z $(ls FWINFO* | grep -i ${modelname}) ] && errcode="1"
This addition also prevents needing to factory reset after flashing
for some boards that also have these lines in the script
\# Support downgrade but do default (Smart v2.x.x.x -> senaowrt v1.x.x.x)
[ $(ls FWINFO* | grep -i ${modelname} | cut -d "-" -f4 | cut -c 2) -lt 2 ] && append=""
Signed-off-by: Michael Pratt <mcpratt@pm.me>
INAGAKI Hiroshi [Wed, 9 Mar 2022 14:31:00 +0000 (23:31 +0900)]
realtek: add support for Panasonic Switch-M8eG PN28080K
Panasonic Switch-M8eG PN28080K is a 8 + 1 port gigabit switch, based on
RTL8380M.
Specification:
- SoC : Realtek RTL8380M
- RAM : DDR3 128 MiB (Winbond W631GG8KB-15)
- Flash : SPI-NOR 32 MiB (Macronix MX25L25635FMI-10G)
- Ethernet : 10/100/1000 Mbps x8 + 1
- port 1-8 : TP, RTL8218B (SoC)
- port 9 : SFP, RTL8380M (SoC)
- LEDs/Keys : 7x / 1x
- UART : RS-232 port on the front panel (connector: RJ-45)
- 3:TX, 4:GND, 5:GND, 6:RX (pin number: RJ-45)
- 9600n8
- Power : 100-240 VAC, 50/60 Hz, 0.5 A
- Plug : IEC 60320-C13
- Stock OS : VxWorks based
Flash instruction using initramfs image:
1. Prepare the TFTP server with the IP address 192.168.1.111
2. Rename the OpenWrt initramfs image to "
0101A8C0.img" and place it to
the TFTP directory
3. Download the official upgrading firmware (ex: pn28080k_v30000.rom)
and place it to the TFTP directory
4. Boot M8eG and interrupt the U-Boot with Ctrl + C keys
5. Execute the following commands and boot with the OpenWrt initramfs
image
rtk network on
tftpboot 0x81000000
bootm
6. Backup mtdblock files to the computer by scp or anything and reboot
7. Interrupt the U-Boot and execute the following commands to re-create
filesystem in the flash
ffsmount c:/
ffsfmt c:/
this step takes a long time, about ~ 4 mins
8. Execute the following commands to put the official images to the
filesystem
updatert <official image>
example:
updatert pn28080k_v30000.rom
this step takes about ~ 40 secs
9. Set the environment variables of the U-Boot by the following commands
setenv loadaddr 0xb4e00000
setenv bootcmd bootm
saveenv
10: Download the OpenWrt initramfs image and boot with it
tftpboot 0x81000000
0101A8C0.img
bootm
11: On the initramfs image, download the sysupgrade image and perform
sysupgrade with it
sysupgrade <imagename>
12: Wait ~ 120 seconds to complete flashing
Note:
- "Switch-M8eG" is a model name, and "PN28080K" is a model number.
Switch-M8eG has an another (old) model number ("PN28080"), it's not a
Realtek based hardware.
- Switch-M8eG has a "POWER" LED (Green), but it's not connected to any
GPIO pin.
- The U-Boot checks the runtime images in the flash when booting and
fails to execute anything in "bootcmd" variable if the images are not
exsisting.
- A filesystem is formed in the flash (0x100000-0x1DFFFFF) on the stock
firmware and it includes the stock images, configuration files and
checksum files. It's unknown format, can't be managed on the OpenWrt.
To get the enough space for OpenWrt, move the filesystem to the head
of "fs_reserved" partition by execution of "ffsfmt" and "updatert".
- On the other devices in the same series of Switch-M8eG PN28080K, the
INT pin on the PCA9555 is not connected to anywhere.
Back to the stock firmware:
1. Delete "loadaddr" variable and set "bootcmd" to the original value
on U-Boot:
setenv loadaddr
setenv bootcmd 'bootm 0x81000000'
on OpenWrt:
fw_setenv loadaddr
fw_setenv bootcmd 'bootm 0x81000000'
2. Perform reset or reboot
on U-Boot:
reset
on OpenWrt:
reboot
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Reviewed-by: Sander Vanheule <sander@svanheule.net>
INAGAKI Hiroshi [Wed, 9 Mar 2022 14:30:59 +0000 (23:30 +0900)]
realtek: enable pca953x driver for rtl838x subtarget
The system status LED on Panasonic Switch-M8eG PN28080K is connected to
a PCA9539PW. To use the LED as a status LED of OpenWrt while booting,
enable the pca953x driver and built-in to the kernel.
Also enable CONFIG_GPIO_PCA953X_IRQ to use interrupt via RTL83xx GPIO.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Acked-by: Sander Vanheule <sander@svanheule.net>
Martin Kennedy [Sat, 5 Mar 2022 19:02:36 +0000 (14:02 -0500)]
realtek: add ZyXEL GS1900-24 v1 support
The ZyXEL GS1900-24 v1 is a 24 port switch with two SFP ports, similar to
the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-24 v1
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB
* RAM: Winbond W9751G8KB-25 64 MiB DDR2 SDRAM
* Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs:
* 1 PWR LED (green, not configurable)
* 1 SYS LED (green, configurable)
* 24 ethernet port link/activity LEDs (green, SoC controlled)
* 2 SFP status/activity LEDs (green, SoC controlled)
* Buttons:
* 1 "RESET" button on front panel (soft reset)
* 1 button ('SW1') behind right hex grate (hardwired power-off)
* Power: 120-240V AC C13
* UART: Internal populated 10-pin header ('J5') providing RS232;
connected to SoC UART through a SIPEX 3232EC for voltage
level shifting.
* 'J5' RS232 Pinout (dot as pin 1):
2) SoC RXD
3) GND
10) SoC TXD
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
flashed to the "Active" partition. If the second option is selected,
OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-initramfs-kernel.bin
file by your preferred method to the previously determined partition.
When prompted, select to boot from the newly flashed image, and reboot
the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-squashfs-sysupgrade.bin
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
> Since the GS1900-24 v1 is a dual-partition device, you want to keep the
OEM firmware on the backup partition for the time being. OpenWrt can
only be installed in the first partition anyway (hardcoded in the
DTS). To ensure we are set to boot from the first partition, issue the
following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x81f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-squashfs-sysupgrade.bin
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
Tianling Shen [Wed, 9 Mar 2022 02:35:04 +0000 (10:35 +0800)]
kernel/modules: add kmod-inet-diag package
Add option to compile kmod-inet-diag, support for INET (TCP, DCCP, etc)
socket monitoring interface used by native Linux tools such as ss.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
John Audia [Tue, 8 Mar 2022 22:01:48 +0000 (17:01 -0500)]
kernel: bump 5.10 to 5.10.104
All patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200
Signed-off-by: John Audia <graysky@archlinux.us>
Rosen Penev [Mon, 7 Mar 2022 04:46:22 +0000 (20:46 -0800)]
tools/ccache: update to 4.6
Full changelog: https://ccache.dev/releasenotes.html#_ccache_4_6
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Mon, 7 Mar 2022 04:53:47 +0000 (20:53 -0800)]
tools/fakeroot: update to 1.28
Refreshed patches.
Upstream says there's only a bugfix for GNU Hurd.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Mon, 7 Mar 2022 04:30:53 +0000 (20:30 -0800)]
tools/cmake: update to 3.22.3
Seems to be mostly pthread fixes.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Mon, 7 Mar 2022 05:02:33 +0000 (21:02 -0800)]
tools/mtools: update to 4.0.38
No real changelog available.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Etienne Champetier [Sun, 13 Mar 2022 05:24:13 +0000 (00:24 -0500)]
iptables: backport missing init_extensions6() calls
This fixes ip6tables-nft no being able to use built-in
extensions like icmp6.
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
Florian Eckert [Wed, 2 Mar 2022 08:42:52 +0000 (09:42 +0100)]
ipset: add backport patch for IPv6 nftables ipset-translation
When porting mwan3 from iptables to nftables I tried the new translation
tool for ipset ipset-translate. I noticed that no IPv6 ipset can be
created with the tool. I have reported the problem to the upstream
project and the following patch fixes the problem.
Until this upsream is included in a new release, this patch should be
used in Openwrt.
https://lore.kernel.org/netfilter-devel/
20220228190217.
2256371-1-pablo@netfilter.org/T/#m09cc3cb738f2e42024c7aecf5b7240d9f6bbc19c
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Rosen Penev [Sat, 12 Mar 2022 22:58:10 +0000 (14:58 -0800)]
tools/expat: enable DTD
Fixes gdb usage, which depends on it.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Rosen Penev [Mon, 7 Mar 2022 04:58:29 +0000 (20:58 -0800)]
tools/expat: update to 2.4.7
Mostly a bug fix to the bug fix to CVE-2022-25236
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Joe Mullally [Tue, 8 Mar 2022 19:33:37 +0000 (19:33 +0000)]
ramips: Apply pinctrl DTS changes to TL-WPA8631P
Applies changes from
7774b86019 to new device committed later. Fix some
whitespace in the DTS. Use standard model name format in DTS.
Fixes: 6c743c3006f9 ("ramips: Add support for TP-Link TL-WPA8631P v3")
Signed-off-by: Joe Mullally <jwmullally@gmail.com>
Reported-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Sven Schwermer [Wed, 9 Mar 2022 08:46:41 +0000 (09:46 +0100)]
ath79: Add LED labels for Airtight C-75
Keep labels since OpenWrt userland tooling (get_dt_led) depends on them
to find the LED instances referenced by the led-* aliases.
The label for the amber power LED was removed in
4eefdc7adb.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
Chukun Pan [Mon, 10 Jan 2022 04:28:40 +0000 (12:28 +0800)]
ramips: update WLAN MAC address of JCG Y2
MAC addresses on OEM firmware:
04:xx:xx:xx:xx:c8 factory 0x4 wlan2g
06:xx:xx:xx:xx:c8 [not on flash] wlan5g
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Chukun Pan [Sun, 9 Jan 2022 04:16:06 +0000 (12:16 +0800)]
ramips: update WLAN MAC address of Phicomm K2P
The wireless mac address difference of this machine is similar
to that of D-Link DIR-853-R1, so use the same practice.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Dawsen Gao [Sat, 12 Feb 2022 02:21:21 +0000 (10:21 +0800)]
ramips: Add support for Dual-Q H721
Dual-Q H721 is a router platform board, it is the smaller model of
the U7621-06.
The device has the following specifications:
MT7621AT (880 MHz)
256 of RAM (DDR3)
16 MB of FLASH (MX25l12805d SPI)
5x 1 Gbps Ethernet (MT7621 built-in switch)
1x M.2 (NGFF) 3.7V 3A max for 5G M.2 Modem work at USB3.0 mode
1x Minipcie 3.7V 3A max for LTE Modem work at USB2.0 Mode
2x Minipcie for WIFI card
4x Lan+1x Wan 10/100M/1000M RJ45 port
14x LEDs (1x GPIO-controlled)
1x reset button
1x UART header (4-pins)
1x mico SD-card reader
1x DC jack for main power (5~27 V)
The following has been tested and is working:
Ethernet switch
miniPCIe slots (tested with Wi-Fi cards and LTE modem cards)
miniSIM slot (works with normal size simcard)
sysupgrade
reset button
micro SD-card reader
Installation:
This board has no locked down bootloader. The seller can be asked to
install openwrt, so upgrades are standard sysupgrade method.
Recovery:
This board contains a Chinese, closed-source bootloader called Breed
(Boot and Recovery Environment for Embedded Devices). Breed supports web
recovery and to enter it, you keep the reset button pressed for around
5 seconds during boot. Your machine will be assigned an IP through DHCP
and the router will use IP address 192.168.1.1. The recovery website is
in Chinese, but is easy to use. Click on the second item in the list to
access the recovery page, then the second item on the next page is where
you select the firmware. In order to start the recovery, you click the
button at the bottom.
Signed-off-by: Dawsen Gao <dawsen_gao@163.com>
[change author name (used SoB one), add ethernet pinctrl,
apply sorting to device recipe]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
projects / openwrt / staging / linusw.git / log