Borislav Petkov [Sun, 7 Jun 2009 13:37:05 +0000 (15:37 +0200)]
ide-tape: change IDE_AFLAG_IGNORE_DSC non-atomically
There are two sites where the flag is being changed: ide_retry_pc
and idetape_do_request. Both codepaths are protected by hwif->busy
(ide_lock_port) and therefore we shouldn't need the atomic accesses.
Spotted-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Sun, 7 Jun 2009 13:37:05 +0000 (15:37 +0200)]
pdc202xx_old: kill resetproc() method
The driver's resetproc() method resets both channels at once -- most probably
by driving RESET- on them. Not only such reset can severely disturb concurrent
operations on another channel, it also ensues 2-second delay, while there's no
apparent reason why SRST reset being performed prior to resetproc() call needs
to be followed up by another reset.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Sun, 7 Jun 2009 13:37:04 +0000 (15:37 +0200)]
pdc202xx_old: don't call pdc202xx_reset() on IRQ timeout
The driver's dma_lost_irq() and dma_clear() methods call pdc202xx_reset()
which resets both channels at once -- most probably by driving RESET- on them.
Not only such reset can severely disturb concurrent operations on another
channel, it is also a clear overkill (especially in the first case) and is
completely unexpected and thus not properly handled by the IDE core in this
context (in the second case the usual SRST reset would most probably ensue
anyway though); it also causes quite arbitrary 2-second delay. Hence, use the
standard ide_dma_lost_irq() method and don't install the optional dma_clear()
method at all -- the driver should do well without this age-old cruft...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Sun, 7 Jun 2009 13:37:03 +0000 (15:37 +0200)]
pdc202xx_old: use ide_dma_test_irq()
The driver's dma_test_irq() method, although tests some chip specific interrupt
bits, finally always relies on the SFF-8038i standard interrupt bit. I see no
point in testing the bits that are not trusted anyway -- the driver should be
fully able to use the standard method implemetation, ide_dma_test_irq().
With this change 'pdc202xx_dma_ops' finally becomes identical to 'sff_dma_ops',
and we can get rid of it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Sun, 7 Jun 2009 12:27:11 +0000 (14:27 +0200)]
Merge branch 'for-linus' into for-next
Bartlomiej Zolnierkiewicz [Sun, 7 Jun 2009 11:52:52 +0000 (13:52 +0200)]
ide: preserve Host Protected Area by default (v2)
From the perspective of most users of recent systems, disabling Host
Protected Area (HPA) can break vendor RAID formats, GPT partitions and
risks corrupting firmware or overwriting vendor system recovery tools.
Unfortunately the original (kernels < 2.6.30) behavior (unconditionally
disabling HPA and using full disk capacity) was introduced at the time
when the main use of HPA was to make the drive look small enough for the
BIOS to allow the system to boot with large capacity drives.
Thus to allow the maximum compatibility with the existing setups (using
HPA and partitioned with HPA disabled) we automically disable HPA if
any partitions overlapping HPA are detected. Additionally HPA can also
be disabled using the "nohpa" module parameter (i.e. "ide_core.nohpa=0.0"
to disable HPA on /dev/hda).
v2:
Fix ->resume HPA support.
While at it:
- remove stale "idebus=" entry from Documentation/kernel-parameters.txt
Cc: Robert Hancock <hancockrwd@gmail.com>
Cc: Frans Pop <elendil@planet.nl>
Cc: "Andries E. Brouwer" <Andries.Brouwer@cwi.nl>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[patch description was based on input from Alan Cox and Frans Pop]
Emphatically-Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Sun, 7 Jun 2009 11:52:52 +0000 (13:52 +0200)]
ide-gd: implement block device ->set_capacity method (v2)
* Use ->probed_capacity to store native device capacity for ATA disks.
* Add ->set_capacity method to struct ide_disk_ops.
* Implement disk device ->set_capacity method for ATA disks.
* Implement block device ->set_capacity method.
v2:
* Check if LBA and HPA are supported in ide_disk_set_capacity().
* According to the spec the SET MAX ADDRESS command shall be
immediately preceded by a READ NATIVE MAX ADDRESS command.
* Add ide_disk_hpa_{get_native,set}_capacity() helpers.
Together with the previous patch adding ->set_capacity block device
method this allows automatic disabling of Host Protected Area (HPA)
if any partitions overlapping HPA are detected.
Cc: Robert Hancock <hancockrwd@gmail.com>
Cc: Frans Pop <elendil@planet.nl>
Cc: "Andries E. Brouwer" <Andries.Brouwer@cwi.nl>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Emphatically-Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Sun, 7 Jun 2009 11:52:52 +0000 (13:52 +0200)]
partitions: add ->set_capacity block device method
* Add ->set_capacity block device method and use it in rescan_partitions()
to attempt enabling native capacity of the device upon detecting the
partition which exceeds device capacity.
* Add GENHD_FL_NATIVE_CAPACITY flag to try limit attempts of enabling
native capacity during partition scan.
Together with the consecutive patch implementing ->set_capacity method in
ide-gd device driver this allows automatic disabling of Host Protected Area
(HPA) if any partitions overlapping HPA are detected.
Cc: Robert Hancock <hancockrwd@gmail.com>
Cc: Frans Pop <elendil@planet.nl>
Cc: "Andries E. Brouwer" <Andries.Brouwer@cwi.nl>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Emphatically-Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Sun, 7 Jun 2009 11:52:51 +0000 (13:52 +0200)]
partitions: warn about the partition exceeding device capacity
The current warning message says only about the kernel's action taken
without mentioning the underlying reason behind it.
Noticed-by: Robert Hancock <hancockrwd@gmail.com>
Cc: Frans Pop <elendil@planet.nl>
Cc: "Andries E. Brouwer" <Andries.Brouwer@cwi.nl>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Emphatically-Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Sun, 7 Jun 2009 11:52:50 +0000 (13:52 +0200)]
pdc202xx_old: fix resetproc() method
pdc202xx_reset() calls pdc202xx_reset_host() twice, for both channels, while
that function actually twiddles the single, shared software reset bit -- the
net effect is a duplicated reset and horrendous 4 second delay happening not
only on a channel reset but also when dma_lost_irq() and dma_clear() methods
are called. Fold pdc202xx_reset_host() into pdc202xx_reset(), fix printk(),
and move it before the actual reset...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Sun, 7 Jun 2009 11:52:50 +0000 (13:52 +0200)]
pdc202xx_old: fix 'pdc20246_dma_ops'
Commit
ac95beedf8bc97b24f9540d4da9952f07221c023 (ide: add struct ide_port_ops
(take 2)) erroneously converted the driver's dma_timeout() and dma_lost_irq()
methods to call the driver's resetproc() method regardless of whether it was
defined for this specific controller while it hadn't been defined and hence
called for PDC20246. So the dma_clear() method, the successor of dma_timeout(),
shouldn't exist and the dma_lost_irq() method should be standard for PDC20246.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Sat, 30 May 2009 18:06:54 +0000 (20:06 +0200)]
ide_pci_generic: add quirk for Netcell ATA RAID
We need to explicitly mark words 85-87 as valid ones since
firmware doesn't do it.
This should fix support for LBA48 and FLUSH CACHE [EXT] command
which stopped working after we applied more strict checking of
identify words in:
commit
942dcd85bf8edf38cdc3745306ca250684d99a61
("ide: idedisk_supports_lba48() -> ata_id_lba48_enabled()")
and
commit
4b58f17d7c45a8e5f4acda641bec388398b9c0fa
("ide: ide_id_has_flush_cache() -> ata_id_flush_enabled()")
Reported-and-tested-by: "Trevor Hemsley" <trevor.hemsley@ntlworld.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Fri, 22 May 2009 15:10:55 +0000 (17:10 +0200)]
Merge branch 'for-linus' into for-next
Harald Welte [Fri, 22 May 2009 14:23:39 +0000 (16:23 +0200)]
via82cxxx: Add VIA VX855 PCI Device ID
This patch adds the PCI Device ID 0xc409 to the PCI ID table of via82cxxx.c,
as well as the 0x8409 south bridge ID.
This is required to make the IDE driver work on the VX855/VX875 integrated
chipset.
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Bruce Chang <BruceChang@via.com.tw>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Fri, 22 May 2009 14:23:38 +0000 (16:23 +0200)]
ide: report timeouts in ide_busy_sleep()
* change 'hwif' argument to 'drive'
* report an error on timeout
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Fri, 22 May 2009 14:23:38 +0000 (16:23 +0200)]
ide: improve failed opcode reporting
Nowadays we (almost) always store the currently executing command
in hwif->cmd so we can use it for the failed opcode reporting.
Cc: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Fri, 22 May 2009 14:23:37 +0000 (16:23 +0200)]
ide: fix printk() levels in ide_dump_ata[pi]_error()
Fixes "<3>" in error messages like this one:
hdc: cdrom_decode_status: error=0x40 <3>{ LastFailedSense=0x04 }
Reported-by: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Fri, 22 May 2009 14:23:37 +0000 (16:23 +0200)]
ide: fix OOPS during ide-cd error recovery
On Tuesday 19 May 2009 20:29:28 Martin Lottermoser wrote:
> hdc: cdrom_decode_status: error=0x40 <3>{ LastFailedSense=0x04 }
> ide: failed opcode was: unknown
> hdc: DMA disabled
> ------------[ cut here ]------------
> kernel BUG at drivers/ide/ide-io.c:872!
It is possible for ide-cd to ignore ide_error()'s return value under
some circumstances. Workaround it in ide_intr() and ide_timer_expiry()
by checking if there is a device/port reset pending currently.
Fixes bug #13345:
http://bugzilla.kernel.org/show_bug.cgi?id=13345
Reported-by: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Reported-and-tested-by: Modestas Vainius <modestas@vainius.eu>
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Fri, 22 May 2009 14:23:36 +0000 (16:23 +0200)]
ide: fix 40-wire cable detection for TSST SH-S202* ATAPI devices (v2)
Since 2.6.26 we support UDMA66 on ATAPI devices requiring IVB quirk:
commit
8588a2b732928b343233af9b1855705b8286bed4
("ide: add SH-S202J to ivb_list[]")
We also later added support for more such devices in:
commit
e97564f362a93f8c248246c19828895950341252
("ide: More TSST drives with broken cable detection")
and in:
commit
3ced5c49bd2d1f2c7f769e3a54385883de63a652
("ide: add TSSTcorp CDDVDW SH-S202H to ivb_list[]")
It turns out that such devices lack cable detection altogether
(which in turn results in incorrect detection of 40-wire cables
by our current cable detection strategy) so always handle them
by trusting host-side cable detection only.
v2:
Model detection fixup from Martin.
Reported-and-tested-by: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Sun, 17 May 2009 17:12:25 +0000 (19:12 +0200)]
ide: remove hw_regs_t typedef
Remove hw_regs_t typedef and rename struct hw_regs_s to struct ide_hw.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Sun, 17 May 2009 17:12:24 +0000 (19:12 +0200)]
ide: pass number of ports to ide_host_{alloc,add}() (v2)
Pass number of ports to ide_host_{alloc,add}() and then update
all users accordingly.
v2:
- drop no longer needed NULL initializers in buddha.c, cmd640.c and gayle.c
(noticed by Sergei)
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Sun, 17 May 2009 17:12:22 +0000 (19:12 +0200)]
ide: remove chipset field from hw_regs_t
* Convert host drivers that still use hw_regs_t's chipset field to use
the one in struct ide_port_info instead.
* Move special handling of ide_pci chipset type from ide_hw_configure()
to ide_init_port().
* Remove chipset field from hw_regs_t.
While at it:
- remove stale comment in delkin_cb.c
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Sun, 17 May 2009 17:12:21 +0000 (19:12 +0200)]
ide: replace special_t typedef by IDE_SFLAG_* flags
Replace:
- special_t typedef by IDE_SFLAG_* flags
- 'special_t special' ide_drive_t's field by 'u8 special_flags' one
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Sun, 17 May 2009 17:12:18 +0000 (19:12 +0200)]
ide: merge ide_disk_special() into do_special() (v2)
While at it:
- change debug printk() level to KERN_DEBUG and use __func__
- update documentation
v2:
- fix DEBUG build (noticed by Sergei)
There should be no functional changes caused by this patch.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Sun, 17 May 2009 17:12:18 +0000 (19:12 +0200)]
ide: BUG() on unknown flags in ide_disk_special()
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Joao Ramos [Sun, 17 May 2009 15:22:54 +0000 (17:22 +0200)]
ide: try to use PIO Mode 0 during probe if possible
Initially set PIO Mode 0 for all host drivers that have a 'set_pio_mode'
method before the IDE core figures out the most suited PIO mode for the
attached device.
Signed-off-by: Joao Ramos <joao.ramos@inov.pt>
Cc: Sergei Shtylyov <sshtylyov@ru.montavista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Mark de Wever [Sun, 17 May 2009 15:22:53 +0000 (17:22 +0200)]
ide-tape: fix debug call
This error only occurs when IDETAPE_DEBUG_LOG is enabled.
Signed-off-by: Mark de Wever <koraq@xs4all.nl>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Sat, 16 May 2009 17:49:03 +0000 (19:49 +0200)]
Merge branch 'for-linus' into for-next
Alan Cox [Sat, 16 May 2009 17:03:36 +0000 (19:03 +0200)]
piix: The Sony TZ90 needs the cable type hardcoding
The Sony TZ90 needs the cable type hardcoding. See bug #12734
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reported-by: Jonathan E. Snow <jesnow@uh.edu>
[bart: port it from ata_piix to piix and give reporter the proper credit]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Sat, 16 May 2009 17:03:36 +0000 (19:03 +0200)]
icside: register second channel of version 6 PCB
The second IDE channel of version 6 PCB is not being registered anymore since
the commit
48c3c1072651922ed153bcf0a33ea82cf20df390 (ide: add struct ide_host
(take 3)).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Tejun Heo [Sat, 18 Apr 2009 22:00:41 +0000 (07:00 +0900)]
ide-tape: remove back-to-back REQUEST_SENSE detection
Impact: fix an oops which always triggers
ide_tape_issue_pc() assumed drive->pc isn't NULL on invocation when
checking for back-to-back request sense issues but drive->pc can be
NULL and even when it's not NULL, it's not safe to dereference it once
the previous command is complete because pc could have been freed or
was on stack. Kill back-to-back REQUEST_SENSE detection.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Anton Vorontsov [Thu, 30 Apr 2009 16:38:01 +0000 (18:38 +0200)]
alim15x3: Remove historical hacks, re-enable init_hwif for PowerPC
Some time ago we had to disable init_hwif callback for PowerPC builds.
That was because of a historical IRQ overwrite in the driver, which
was causing IDE malfunction on the MPC8610HPCD PowerPC boards.
It's unclear whether this overwrite is still useful, but it is proven
to cause a bit of harm, and today some PowerPC targets (Xilinx ML510,
as reported by Roderick Colenbrander) need the init_hwif, so we have
to re-enable it and remove the overwrite.
Reported-by: Roderick Colenbrander <thunderbird2k@gmail.com>
Suggested-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Thu, 30 Apr 2009 16:28:35 +0000 (18:28 +0200)]
Merge branch 'for-linus' into for-next
Borislav Petkov [Thu, 30 Apr 2009 16:24:34 +0000 (18:24 +0200)]
ide-cd: fix REQ_QUIET tests in cdrom_decode_status
Original patch (
dfa4411cc3a690011cab90e9a536938795366cf9) was buggy.
This is a more proper fix which introduces blk_rq_quiet() macro
alleviating the need for dumb, too short caching variables.
Thanks to Helge Deller and Bart for debugging this.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Reported-and-tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Thu, 23 Apr 2009 20:56:58 +0000 (22:56 +0200)]
Merge branch 'for-linus' into for-next
Bartlomiej Zolnierkiewicz [Thu, 23 Apr 2009 20:53:45 +0000 (22:53 +0200)]
MAINTAINERS: update IDE entry
By a popular demand quilt tree was replaced by a git one.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Thu, 23 Apr 2009 20:53:45 +0000 (22:53 +0200)]
palm_bk3710: palm_bk3710_udmatimings[] CodingStyle fixup
Remove superfluous commas and add missing whitespaces.
Noticed-by: Joe Perches <joe@perches.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
David Brownell [Thu, 23 Apr 2009 20:53:43 +0000 (22:53 +0200)]
palm_bk3710: those registers/bitfields don't exist
Bugfixes noted by checking the code against the controller
documentation (TI document number SPRUE21):
- Remove declarations for eight non-existent registers (!);
and remove accesses to two of them.
- Remove access to various non-existent bitfields in some of
the registers which *do* exist (those fields must-be-zero).
- Provide comment to replace bogus reset logic (removed above,
it relied on non-existent bitfields). Resets require GPIO
help; this driver doesn't currently know about that.
With some minor cleanup: relocate a comment, avoid an extra
lookup of the PIO timings.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Wed, 22 Apr 2009 18:38:45 +0000 (20:38 +0200)]
Merge branch 'for-linus' into for-next
Bartlomiej Zolnierkiewicz [Wed, 22 Apr 2009 18:33:41 +0000 (20:33 +0200)]
mediabay: fix build for CONFIG_BLOCK=n
On Tuesday 14 April 2009 20:31:21 Subrata Modak wrote:
> Observed the following build error:
> ---
> CC drivers/macintosh/mediabay.o
> In file included from drivers/macintosh/mediabay.c:21:
> include/linux/ide.h:605: error: field ‘request_sense_rq’ has incomplete
> type
> make[2]: *** [drivers/macintosh/mediabay.o] Error 1
> make[1]: *** [drivers/macintosh] Error 2
> make: *** [drivers] Error 2
> ---
mediabay shouldn't include <linux/ide.h> unconditionally so
remove the superfluous include from mediabay.c (<asm/mediabay.h>
will pull <linux/ide.h> in for CONFIG_BLK_DEV_IDE_PMAC=y).
Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bruno Prémont [Wed, 22 Apr 2009 18:33:41 +0000 (20:33 +0200)]
ide: Stop disks on reboot for laptop which cuts power
My laptop (Acer Travelmate 660) always cuts the power when rebooting
which causes the disk to emergency-park it's head.
Add a dmi check to stop disk as for shutdown on this laptop.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Helge Deller [Wed, 22 Apr 2009 18:33:40 +0000 (20:33 +0200)]
ide-cd: fix kernel crash on hppa regression
With 2.6.30-rc2 I face a kernel crash on the 32bit hppa architecture
due to ide-cd when udev creates the device nodes at startup:
Kernel Fault: Code=26 regs=
8ed34c40 (Addr=
00000024)
IASQ:
00000000 00000000 IAOQ:
1034b5ac 1034b5b0
IIR:
4ab30048 ISR:
00000000 IOR:
00000024
CPU: 0 CR30:
8ed34000 CR31:
ffff55ff
ORIG_R28:
00000000
IAOQ[0]: ide_complete_rq+0x2c/0x70
IAOQ[1]: ide_complete_rq+0x30/0x70
RP(r2): cdrom_newpc_intr+0x178/0x46c
Backtrace:
[<
1035c608>] cdrom_newpc_intr+0x178/0x46c
[<
1034c494>] ide_intr+0x1b0/0x214
[<
1016d284>] handle_IRQ_event+0x70/0x150
[<
1016d4b0>] __do_IRQ+0x14c/0x1cc
[<
102f7864>] superio_interrupt+0x88/0xbc
[<
1016d284>] handle_IRQ_event+0x70/0x150
[<
1016d4b0>] __do_IRQ+0x14c/0x1cc
[<
10112efc>] do_cpu_irq_mask+0x9c/0xd0
[<
10116068>] intr_return+0x0/0x4
This crash seems to happen due to an uninitialized variable "rc".
The compiler even warns about that:
CC drivers/ide/ide-cd.o
/mnt/sda4/home/cvs/parisc/git-kernel/linus-linux-2.6/drivers/ide/ide-cd.c: In function `cdrom_newpc_intr':
/mnt/sda4/home/cvs/parisc/git-kernel/linus-linux-2.6/drivers/ide/ide-cd.c:612: warning: `rc' might be used uninitialized in this function
After applying the trivial patch below, which just initializes
the variable to zero, the kernel doesn't crash any longer:
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...
hda: command error: status=0x51 { DriveReady SeekComplete Error }
hda: command error: error=0x54 <3>{ AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
done.
Signed-off-by: Helge Deller <deller@gmx.de>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Cc: Linus <torvalds@linux-foundation.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
David Brownell [Wed, 22 Apr 2009 18:33:40 +0000 (20:33 +0200)]
palm_bk3710: UDMA performance fix
Fix UDMA throughput bug: tCYC averages t2CYCTYP/2, but the code
previously assumed it was the same as t2CYCTYP. (That is, it was
using just one clock edge, not both.) Move the table's type
declaration so it's adjacent to the table, making it more clear
what those numbers mean.
On one system this change increased throughput by almost 4x: UDMA/66
sometimes topped 23 MB/sec (on a drive known to do much better). On
another system it was around a 10% win (UDMA/66 up to 7+ MB/sec).
The difference might be caused by the ratio between memory and IDE
clocks. In the system with large speedup, this was exactly 2 (as a
workaround for a rev 1.1 silicon bug). The other system used a more
standard ratio of 1.63 (and rev 2.1 silicon) ... clock domain synch
might have some issues, they're not unheard-of.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Tejun Heo [Tue, 21 Apr 2009 03:16:56 +0000 (12:16 +0900)]
ide-dma: don't reset request fields on dma_timeout_retry()
Impact: drop unnecessary code
Now that everything uses bio and block operations, there is no need to
reset request fields manually when retrying a request. Every field is
guaranteed to be always valid. Drop unnecessary request field
resetting from ide_dma_timeout_retry().
Signed-off-by: Tejun Heo <tj@kernel.org>
Tejun Heo [Sat, 18 Apr 2009 23:46:03 +0000 (08:46 +0900)]
ide: drop rq->data handling from ide_map_sg()
Impact: remove code path which is no longer necessary
All IDE data transfers now use rq->bio. Simplify ide_map_sg()
accordingly.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Tejun Heo [Sat, 18 Apr 2009 23:46:03 +0000 (08:46 +0900)]
ide-atapi: kill unused fields and callbacks
Impact: remove fields and code paths which are no longer necessary
Now that ide-tape uses standard mechanisms to transfer data, special
case handling for bh handling can be dropped from ide-atapi. Drop the
followings.
* pc->cur_pos, b_count, bh and b_data
* drive->pc_update_buffers() and pc_io_buffers().
Signed-off-by: Tejun Heo <tj@kernel.org>
Tejun Heo [Sat, 18 Apr 2009 23:46:03 +0000 (08:46 +0900)]
ide-tape: simplify read/write functions
Impact: cleanup
idetape_chrdev_read/write() functions are unnecessarily complex when
everything can be handled in a single loop. Collapse
idetape_add_chrdev_read/write_request() into the rw functions and
simplify the implementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Tejun Heo [Sat, 18 Apr 2009 23:46:03 +0000 (08:46 +0900)]
ide-tape: use byte size instead of sectors on rw issue functions
Impact: cleanup
Byte size is what most issue functions deal with, make
idetape_queue_rw_tail() and its wrappers take byte size instead of
sector counts. idetape_chrdev_read() and write() functions are
converted to use tape->buffer_size instead of ctl from tape->cap.
This cleans up code a little bit and will ease the next r/w
reimplementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Tejun Heo [Sat, 18 Apr 2009 23:46:02 +0000 (08:46 +0900)]
ide-tape: unify r/w init paths
Impact: cleanup
Read and write init paths are almost identical. Unify them into
idetape_init_rw().
Signed-off-by: Tejun Heo <tj@kernel.org>
Tejun Heo [Sat, 18 Apr 2009 23:46:02 +0000 (08:46 +0900)]
ide-tape: kill idetape_bh
Impact: kill now unnecessary idetape_bh
With everything using standard mechanisms, there is no need for
idetape_bh anymore. Kill it and use tape->buf, cur and valid to
describe data buffer instead.
Changes worth mentioning are...
* idetape_queue_rq_tail() now always queue tape->buf and and adjusts
buffer state properly before completion.
* idetape_pad_zeros() clears the buffer only once.
Signed-off-by: Tejun Heo <tj@kernel.org>
Tejun Heo [Sat, 18 Apr 2009 23:46:02 +0000 (08:46 +0900)]
ide-tape: use standard data transfer mechanism
Impact: use standard way to transfer data
ide-tape uses rq in an interesting way. For r/w requests, rq->special
is used to carry a private buffer management structure idetape_bh and
rq->nr_sectors and current_nr_sectors are initialized to the number of
idetape blocks which isn't necessary 512 bytes. Also,
rq->current_nr_sectors is used to report back the residual count in
units of idetape blocks.
This peculiarity taxes both block layer and ide. ide-atapi has
different paths and hooks to accomodate it and what a rq means becomes
quite confusing and making changes at the block layer becomes quite
difficult and error-prone.
This patch makes ide-tape use bio instead. With the previous patch,
ide-tape currently is using single contiguos buffer so replacing it
isn't difficult. Data buffer is mapped into bio using
blk_rq_map_kern() in idetape_queue_rw_tail(). idetape_io_buffers()
and idetape_update_buffers() are dropped and pc->bh is set to null to
tell ide-atapi to use standard data transfer mechanism and idetape_bh
byte counts are updated by the issuer on completion using the residual
count.
This change also nicely removes the FIXME in ide_pc_intr() where
ide-tape rqs need to be completed using ide_rq_bytes() instead of
blk_rq_bytes() (although this didn't really matter as the request
didn't have bio).
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Tejun Heo [Sat, 18 Apr 2009 23:46:02 +0000 (08:46 +0900)]
ide-tape: use single continuous buffer
Impact: simpler buffer allocation and handling, kills OOM, fix DMA transfers
ide-tape has its own multiple buffer mechanism using struct
idetape_bh. It allocates buffer with decreasing order-of-two
allocations so that it results in minimum number of segments.
However, the implementation is quite complex and works in a way that
no other block or ide driver works necessitating a lot of special case
handling.
The benefit this complex allocation scheme brings is questionable as
PIO or DMA the number of segments (16 maximum) doesn't make any
noticeable difference and it also doesn't negate the need for multiple
order allocation which can fail under memory pressure or high
fragmentation although it does lower the highest order necessary by
one when the buffer size isn't power of two.
As the first step to remove the custom buffer management, this patch
makes ide-tape allocate single continous buffer. The maximum order is
four. I doubt the change would cause any trouble but if it ever
matters, it should be converted to regular sg mechanism like everyone
else and even in that case dropping custom buffer handling and moving
to standard mechanism first make sense as an intermediate step.
This patch makes the first bh to contain the whole buffer and drops
multi bh handling code. Following patches will make further changes.
This patch has the side effect of killing OOM triggered by allocation
path and fixing DMA transfers. Previously, bug in alloc path
triggered OOM on command issue and commands were passed to DMA engine
without DMA-mapping all the segments.
Signed-off-by: Tejun Heo <tj@kernel.org>
Tejun Heo [Sat, 18 Apr 2009 23:46:02 +0000 (08:46 +0900)]
ide-atapi,tape,floppy: allow ->pc_callback() to change rq->data_len
Impact: allow residual count implementation in ->pc_callback()
rq->data_len has two duties - carrying the number of input bytes on
issue and carrying residual count back to the issuer on completion.
ide-atapi completion callback ->pc_callback() is the right place to do
this but currently ide-atapi depends on rq->data_len carrying the
original request size after calling ->pc_callback() to complete the pc
request.
This patch makes ide_pc_intr(), ide_tape_issue_pc() and
ide_floppy_issue_pc() cache length to complete before calling
->pc_callback() so that it can modify rq->data_len as necessary.
Note: As using rq->data_len for two purposes can make cases like this
incorrect in subtle ways, future changes will introduce separate
field for residual count.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Tejun Heo [Sat, 18 Apr 2009 23:46:02 +0000 (08:46 +0900)]
ide-tape,floppy: fix failed command completion after request sense
Impact: fix infinite retry loop
After a command failed, ide-tape and floppy inserts REQUEST_SENSE in
front of the failed command and according to the result, sets
pc->retries, flags and errors. After REQUEST_SENSE is complete, the
failed command is again at the front of the queue and if the verdict
was to terminate the request, the issue functions tries to complete it
directly by calling drive->pc_callback() and returning ide_stopped.
However, drive->pc_callback() doesn't complete a request. It only
prepares for completion of the request. As a result, this creates an
infinite loop where the failed request is retried perpetually.
Fix it by actually ending the request by calling ide_complete_rq().
Signed-off-by: Tejun Heo <tj@kernel.org>
Tejun Heo [Sat, 18 Apr 2009 22:00:43 +0000 (07:00 +0900)]
ide-pm: don't abuse rq->data
Impact: cleanup rq->data usage
ide-pm uses rq->data to carry pointer to struct request_pm_state
through request queue and rq->special is used to carray pointer to
local struct ide_cmd, which isn't necessary. Use rq->special for
request_pm_state instead and use local ide_cmd in
ide_start_power_step().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Tejun Heo [Sat, 18 Apr 2009 22:00:42 +0000 (07:00 +0900)]
ide-cd,atapi: use bio for internal commands
Impact: unify request data buffer handling
rq->data is used mostly to pass kernel buffer through request queue
without using bio. There are only a couple of places which still do
this in kernel and converting to bio isn't difficult.
This patch converts ide-cd and atapi to use bio instead of rq->data
for request sense and internal pc commands. With previous change to
unify sense request handling, this is relatively easily achieved by
adding blk_rq_map_kern() during sense_rq prep and PC issue.
If blk_rq_map_kern() fails for sense, the error is deferred till sense
issue and aborts the failed command which triggered the sense. Note
that this is a slim possibility as sense prep is done on each command
issue, so for the above condition to actually trigger, all preps since
the last sense issue till the issue of the request which would require
a sense should fail.
* do_request functions might sleep now. This should be okay as ide
request_fn - do_ide_request() - is invoked only from make_request
and plug work. Make sure this is the case by adding might_sleep()
to do_ide_request().
* Functions which access the read sense data before the sense request
is complete now should access bio_data(sense_rq->bio) as the sense
buffer might have been copied during blk_rq_map_kern().
* ide-tape updated to map sg.
* cdrom_do_block_pc() now doesn't have to deal with REQ_TYPE_ATA_PC
special case. Simplified.
* tp_ops->output/input_data path dropped from ide_pc_intr().
Signed-off-by: Tejun Heo <tj@kernel.org>
Borislav Petkov [Sat, 18 Apr 2009 22:00:42 +0000 (07:00 +0900)]
ide-atapi: convert ide-{floppy,tape} to using preallocated sense buffer
Since we're issuing REQ_TYPE_SENSE now we need to allow those types of
rqs in the ->do_request callbacks. As a future improvement, sense_len
assignment might be unified across all ATAPI devices. Borislav to
check with specs and test.
As a result, get rid of ide_queue_pc_head() and
drive->request_sense_rq.
tj: * Init request sense ide_atapi_pc from sense request. In the
longer timer, it would probably better to fold
ide_create_request_sense_cmd() into its only current user -
ide_floppy_get_format_progress().
* ide_retry_pc() no longer takes @disk.
CC: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
CC: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Borislav Petkov [Sat, 18 Apr 2009 22:00:42 +0000 (07:00 +0900)]
ide-cd: convert to using generic sense request
Preallocate a sense request in the ->do_request method and reinitialize
it only on demand, in case it's been consumed in the IRQ handler path.
The reason for this is that we don't want to be mapping rq to bio in
the IRQ path and introduce all kinds of unnecessary hacks to the block
layer.
tj: * Both user and kernel PC requests expect sense data to be stored
in separate storage other than drive->sense_data. Copy sense
data to rq->sense on completion if rq->sense is not NULL. This
fixes bogus sense data on PC requests.
As a result, remove cdrom_queue_request_sense.
CC: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
CC: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Borislav Petkov [Sat, 18 Apr 2009 22:00:42 +0000 (07:00 +0900)]
ide: add helpers for preparing sense requests
This is in preparation of removing the queueing of a sense request out
of the IRQ handler path.
Use struct request_sense as a general sense buffer for all ATAPI
devices ide-{floppy,tape,cd}.
tj: * blk_get_request(__GFP_WAIT) can't be called from do_request() as
it can cause deadlock. Converted to use inline struct request
and blk_rq_init().
* Added xfer / cdb len selection depending on device type.
* All sense prep logics folded into ide_prep_sense() which never
fails.
* hwif->rq clearing and sense_rq used handling moved into
ide_queue_sense_rq().
* blk_rq_map_kern() conversion is moved to later patch.
CC: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
CC: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Tejun Heo [Sat, 18 Apr 2009 22:00:42 +0000 (07:00 +0900)]
ide-cd: don't abuse rq->buffer
Impact: rq->buffer usage cleanup
ide-cd uses rq->buffer to carry pointer to the original request when
issuing REQUEST_SENSE. Use rq->special instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Tejun Heo [Sat, 18 Apr 2009 22:00:42 +0000 (07:00 +0900)]
ide-atapi: don't abuse rq->buffer
Impact: rq->buffer usage cleanup
ide-atapi uses rq->buffer as private opaque value for internal special
requests. rq->special isn't used for these cases (the only case where
rq->special is used is for ide-tape rw requests). Use rq->special
instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Tejun Heo [Sat, 18 Apr 2009 22:00:42 +0000 (07:00 +0900)]
ide-taskfile: don't abuse rq->buffer
Impact: rq->buffer usage cleanup
ide_raw_taskfile() directly uses rq->buffer to carry pointer to the
data buffer. This complicates both block interface and ide backend
request handling. Use blk_rq_map_kern() instead and drop special
handling for REQ_TYPE_ATA_TASKFILE from ide_map_sg().
Note that REQ_RW setting is moved upwards as blk_rq_map_kern() uses it
to initialize bio rw flag.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Tejun Heo [Sat, 18 Apr 2009 22:00:42 +0000 (07:00 +0900)]
ide-floppy: block pc always uses bio
Impact: remove unnecessary code path
Block pc requests always use bio and rq->data is always NULL. No need
to worry about !rq->bio cases in idefloppy_block_pc_cmd(). Note that
ide-atapi uses ide_pio_bytes() for bio PIO transfer which handle sg
fine.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Tejun Heo [Sat, 18 Apr 2009 22:00:41 +0000 (07:00 +0900)]
ide-cd: clear sense buffer before issuing request sense
Impact: code simplification
ide_cd_request_sense_fixup() clears the tail of the sense buffer if
the device didn't completely fill it. This patch makes
cdrom_queue_request_sense() clear the sense buffer before issuing the
command instead of clearing it afterwards. This simplifies code and
eases future changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Tejun Heo [Sat, 18 Apr 2009 22:00:41 +0000 (07:00 +0900)]
ide kill unused ide_cmd->special
Impact: removal of unused field
No one uses ide_cmd->special anymore. Kill it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Tejun Heo [Sat, 18 Apr 2009 22:00:41 +0000 (07:00 +0900)]
ide: don't set REQ_SOFTBARRIER
ide doesn't have to worry about REQ_SOFTBARRIER. Don't set it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Tejun Heo [Sat, 18 Apr 2009 22:00:41 +0000 (07:00 +0900)]
ide: use blk_run_queue() instead of blk_start_queueing()
blk_start_queueing() is being phased out in favor of
[__]blk_run_queue(). Switch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Tejun Heo [Sat, 18 Apr 2009 22:00:41 +0000 (07:00 +0900)]
ide-tape: remove back-to-back REQUEST_SENSE detection
Impact: fix an oops which always triggers
ide_tape_issue_pc() assumed drive->pc isn't NULL on invocation when
checking for back-to-back request sense issues but drive->pc can be
NULL and even when it's not NULL, it's not safe to dereference it once
the previous command is complete because pc could have been freed or
was on stack. Kill back-to-back REQUEST_SENSE detection.
Signed-off-by: Tejun Heo <tj@kernel.org>
Tejun Heo [Sat, 18 Apr 2009 22:00:41 +0000 (07:00 +0900)]
block: clear req->errors on bio completion only for fs requests
Impact: subtle behavior change
For fs requests, rq is only carrier of bios and rq error status as a
whole doesn't mean much. This is the reason why rq->errors is being
cleared on each partial completion of a request as on each partial
completion the error status is transferred to the respective bios.
For pc requests, rq->errors is used to carry error status to the
issuer and thus __end_that_request_first() doesn't clear it on such
cases.
The condition was fine till now as only fs and pc requests have used
bio and thus the bio completion path. However, future changes will
unify data accesses to bio and all non fs users care about rq error
status. Clear rq->errors on bio completion only for fs requests.
In general, the implicit clearing is a bit too subtle especially as
the meaning of rq->errors is completely dependent on low level
drivers. Unifying / cleaning up rq->errors usage and letting llds
manage it would be better. TODO comment added.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jens Axboe <axboe@kernel.dk>
Sergei Shtylyov [Sat, 18 Apr 2009 15:42:20 +0000 (17:42 +0200)]
cs5536: define dma_sff_read_status() method
The driver somehow got merged with the initializer for the dma_sff_read_status()
method missing which caused kernel panic on bootup.
This should fix the kernel.org bug #13026...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Reported-by: Arnd Hannemann <hannemann@nets.rwth-aachen.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Sat, 18 Apr 2009 15:42:20 +0000 (17:42 +0200)]
ide: fix barriers support
Freeing non-slab objects is bad and results in an oops. Fix it.
Reported-and-tested-by: Andrew Price <andy@andrewprice.me.uk>
Cc: Theodore Tso <tytso@mit.edu>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Jack Stone [Sat, 18 Apr 2009 15:42:19 +0000 (17:42 +0200)]
ide: Remove void casts
Remove uneeded void casts
Signed-off-by: Jack Stone <jwjstone@fastmail.fm>
Cc: jeff@garzik.org
Cc: kernel-janitors@vger.kernel.org
Cc: Jack Stone <jwjstone@fastmail.fm>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Sat, 18 Apr 2009 15:42:19 +0000 (17:42 +0200)]
hpt366: use ATA_DMA_* constants
Use ATA_DMA_* constants instead of the bare numbers for the BMIDE register bits.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sergei Shtylyov [Sat, 18 Apr 2009 15:42:19 +0000 (17:42 +0200)]
hpt366: fix HPT370 DMA timeouts
The big driver change in 2.4.19-rc1 introduced a regression for many HPT370[A]
chips -- DMA stopped to work completely, only causing endless timeouts...
The culprit has been identified (at last!): it turned to be the code resetting
the DMA state machine before each transfer. Stop doing it now as this counter-
measure has clearly caused more harm than good.
This should fix the kernel.org bug #7703.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Linus Torvalds [Fri, 17 Apr 2009 23:20:29 +0000 (16:20 -0700)]
Merge branch 'upstream-linus' of git://git./linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] fix build error on drivers/ata/pata_legacy.c
pata_via: Cache and rewrite the device bit
sata_mv: workaround for multi_count errata sata24
sata_mv: tidy up qc->tf usage in qc_prep() functions
Zhenwen Xu [Fri, 17 Apr 2009 07:32:59 +0000 (15:32 +0800)]
[libata] fix build error on drivers/ata/pata_legacy.c
fix those errors:
drivers/ata/pata_legacy.c: In function ‘pdc_data_xfer_vlb’:
drivers/ata/pata_legacy.c:289: error: ‘ap’ undeclared (first use in this function)
drivers/ata/pata_legacy.c:289: error: (Each undeclared identifier is reported only once
drivers/ata/pata_legacy.c:289: error: for each function it appears in.)
drivers/ata/pata_legacy.c: At top level:
drivers/ata/pata_legacy.c:869: error: ‘ATA_PFLAG_PIO32_CHANGE’ undeclared here (not in a
+function)
make[2]: *** [drivers/ata/pata_legacy.o] Error 1
make[1]: *** [drivers/ata] Error 2
Signed-off-by: Zhenwen Xu <helight.xu@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Alan Cox [Fri, 17 Apr 2009 11:21:21 +0000 (12:21 +0100)]
pata_via: Cache and rewrite the device bit
Some VIA chipsets will reset the DEV bit after IEN changes on ctl. Our
optimised write path avoids doing this but we need to remove the
optimisation on these devices.
[Identified and some original patches proposed by Josehn Chan @ VIA but
discussion then all ground to a halt so given a test case I dug it back out]
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk
Tested-by: Christoph Bisping (bug #13086)
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Mark Lord [Mon, 13 Apr 2009 15:29:34 +0000 (11:29 -0400)]
sata_mv: workaround for multi_count errata sata24
Workaround for errata SATA#24 in sata_mv.
This errata affects WRITE_MULTI* commands when
the device multi_count produces a DRQ block size >= 4Kbytes.
We work around it here by converting such operations
into ordinary PIO_WRITEs instead.
Note that this might result in a PIO FUA write unavoidably being converted
into a non-FUA write. In practice, any system using FUA is also going to be
using DMA rather than PIO, so this shouldn't affect anyone in the real world.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Mark Lord [Mon, 13 Apr 2009 15:27:18 +0000 (11:27 -0400)]
sata_mv: tidy up qc->tf usage in qc_prep() functions
Tidy up qc->tf accesses in the mv_qc_prep() functions.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Linus Torvalds [Fri, 17 Apr 2009 20:53:34 +0000 (13:53 -0700)]
Merge git://git./linux/kernel/git/gregkh/staging-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6: (43 commits)
staging: slicoss: update README
otus/zdusb.c: additional USB idnetifier
Staging: go7007: fix build issues
Staging: sxg: Fix leaks and checksum errors in transmit code path
Staging: sxg: Fix sleep in atomic context warning while loading driver
Staging: sxg: Use correct queue_id for transmitting non-TCP packets
Staging: sxg: Fire watchdog timer at end of open routine to change the link
Staging: Pohmelfs: Add load balancing between network states with the same priority.
Staging: Pohmelfs: Added IO permissions and priorities.
Staging: Pohmelfs: Added ->show_stats() callback.
Staging: Pohmelfs: Drop ftrans debugging code.
Staging: Pohmelfs: Use wait_on_page_timeout when waiting for remote directory sync instead of hardcoded 25 seconds.
Staging: Pohmelfs: Reduce debugging noise about non-existing objects.
Staging: Pohmelfs: Sync fs before killing it, since dentry cache is shrunk before writeback is invoked via generic_shutdown_super()
Staging: Pohmelfs: Extend remount option.
Staging: Pohmelfs: Set NETFS_INODE_REMOTE_SYNCED and clear NETFS_INODE_OWNED bits in the root inode.
Staging: Pohmelfs: Added 'need_lock' variable into debug print.
Staging: Pohmelfs: Disable read lock in pohmelfs_getattr().
Staging: Pohmelfs: Move parent lock to the place where we really have to send a lookup request to the server.
Staging: pohmelfs: Populate dentry cache when receiving the new readdir entry.
...
Linus Torvalds [Fri, 17 Apr 2009 20:53:16 +0000 (13:53 -0700)]
Merge git://git./linux/kernel/git/gregkh/driver-core-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
UIO: fix specific device driver missing statement for depmod
Driver core: remove pr_fmt() from dynamic_dev_dbg() printk
driver core: prevent device_for_each_child from oopsing
dynamic debug: resurrect old pr_debug() semantics as pr_devel()
Driver Core: early platform driver
proc: mounts_poll() make consistent to mdstat_poll
sysfs: sysfs poll keep the poll rule of regular file.
driver core: allow non-root users to listen to uevents
driver core: fix driver_match_device
sysfs: don't use global workqueue in sysfs_schedule_callback()
Linus Torvalds [Fri, 17 Apr 2009 20:53:00 +0000 (13:53 -0700)]
Merge git://git./linux/kernel/git/gregkh/usb-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (22 commits)
WUSB: correct format of wusb_chid sysfs file
WUSB: fix oops when completing URBs for disconnected devices
WUSB: disconnect all devices when stopping a WUSB HCD
USB: whci-hcd: check return value of usb_hcd_link_urb_to_ep()
USB: whci-hcd: provide a endpoint_reset method
USB: add reset endpoint operations
USB device codes for Motorola phone.
usb-storage: fix mistake in Makefile
USB: usb-serial ch341: support for DTR/RTS/CTS
Revert USB: usb-serial ch341: support for DTR/RTS/CTS
USB: musb: fix possible panic while resuming
USB: musb: fix isochronous TXDMA (take 2)
USB: musb: sanitize clearing TXCSR DMA bits (take 2)
USB: musb: bugfixes for multi-packet TXDMA support
USB: musb_host, fix ep0 fifo flushing
USB: usb-storage: augment unusual_devs entry for Simple Tech/Datafab
USB: musb_host, minor enqueue locking fix (v2)
USB: fix oops in cdc-wdm in case of malformed descriptors
USB: qcserial: Add extra device IDs
USB: option: Add ids for D-Link DWM-652 3.5G modem
...
Linus Torvalds [Fri, 17 Apr 2009 20:51:14 +0000 (13:51 -0700)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm: (48 commits)
[ARM] S3C24XX: ADC: Check pending queue before freeing adc client
[ARM] S3C: Fix ADC driver sparse warning
[ARM] Osiris: Fix double initialisation in machine block
[ARM] Anubis: Fix sparse warnings for items that should be static
[ARM] JIVE: Fix sparse warnings about items which should be static
[ARM] S3C: Fix sparse warning from missing 's3c_device_hwmon'
[ARM] S3C24XX: Fix sparse error in gpiolib.c
[ARM] 5455/1: Fix IRQ noise from VIC code
[ARM] 5454/1: ep93xx_eth: fix sparse warnings
[ARM] remove .gitignore from include/asm-arm
Update MAINTAINERS
mxc defconfig updates
mx31ads: Mark as having full regulatoion constraints with 1133-EV1 board
mx31ads: Depend on all the WM8350 core dependencies for WM1133-EV1 board
Fix ifdef in plat-mxc/irc.c
MX1ADS: remove I2C ifdefs
qong: remove AIPS[12] mappings from machine-specific iotable
mx31ads: imoux pins should be passed in as unsigned int
MXC: remove orphan imx_init_uart() definition
mx31: pin definition for csi
...
Russell King [Fri, 17 Apr 2009 20:35:56 +0000 (21:35 +0100)]
Merge branch 'defconfig-s3c2410' of git://aeryn.fluff.org.uk/bjdooks/linux
Russell King [Fri, 17 Apr 2009 20:35:44 +0000 (21:35 +0100)]
Merge branch 'v2630-rc2-fixes' of git://aeryn.fluff.org.uk/bjdooks/linux
Stephen Hemminger [Wed, 15 Apr 2009 23:52:16 +0000 (16:52 -0700)]
staging: slicoss: update README
I looked, I gagged, I left
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Daniele Napolitano [Tue, 14 Apr 2009 23:58:33 +0000 (16:58 -0700)]
otus/zdusb.c: additional USB idnetifier
Provide support for WN111v2 USB 802.11n adapter.
Signed-off-by: Daniele Napolitano <dnax88@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Mon, 13 Apr 2009 20:16:54 +0000 (13:16 -0700)]
Staging: go7007: fix build issues
Now that TUNER_SET_TYPE_ADDR is gone from the tree, the older code kicks
in and tries to use TUNER_SET_TYPE, which went away a long time ago.
This patch removes all of this logic, as it should not be needed anymore
now, and by doing so, fixes the build.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mithlesh Thukral [Wed, 25 Mar 2009 10:21:49 +0000 (15:51 +0530)]
Staging: sxg: Fix leaks and checksum errors in transmit code path
Fix the transmit function for the following:
* Free XmtCmd in the error code path. This use to leak memory in
error conditions.
* Do pci mapping after the checksum operations are over. They can
reallocate the skb at a different location.
* Fix UDP checksum errors which were seen in wireshark
Signed-off-by: LinSysSoft Sahara Team <saharaproj@linsyssoft.com>
Signed-off-by: Mithlesh Thukral <mithlesh@linsyssoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mithlesh Thukral [Wed, 25 Mar 2009 10:21:14 +0000 (15:51 +0530)]
Staging: sxg: Fix sleep in atomic context warning while loading driver
Leave a spinlock before calling request_irq(). request_irq() calls kmalloc
which can sleep. This was generating a warning dump while driver is loaded.
Signed-off-by: LinSysSoft Sahara Team <saharaproj@linsyssoft.com>
Signed-off-by: Mithlesh Thukral <mithlesh@linsyssoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mithlesh Thukral [Wed, 25 Mar 2009 10:20:34 +0000 (15:50 +0530)]
Staging: sxg: Use correct queue_id for transmitting non-TCP packets
Use correct queue_id while transmitting non-TCP packets.
They should always use queue 0.
Signed-off-by: LinSysSoft Sahara Team <saharaproj@linsyssoft.com>
Signed-off-by: Mithlesh Thukral <mithlesh@linsyssoft.com>
Mithlesh Thukral [Wed, 25 Mar 2009 10:19:58 +0000 (15:49 +0530)]
Staging: sxg: Fire watchdog timer at end of open routine to change the link
The watchdog timer which updates the link status was not fired at the
end of sxg_entry_open(). Add that.
Signed-off-by: LinSysSoft Sahara Team <saharaproj@linsyssoft.com>
Signed-off-by: Mithlesh Thukral <mithlesh@linsyssoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Evgeniy Polyakov [Fri, 27 Mar 2009 12:04:30 +0000 (15:04 +0300)]
Staging: Pohmelfs: Add load balancing between network states with the same priority.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Evgeniy Polyakov [Fri, 27 Mar 2009 12:04:29 +0000 (15:04 +0300)]
Staging: Pohmelfs: Added IO permissions and priorities.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Evgeniy Polyakov [Fri, 27 Mar 2009 12:04:28 +0000 (15:04 +0300)]
Staging: Pohmelfs: Added ->show_stats() callback.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Evgeniy Polyakov [Fri, 27 Mar 2009 12:04:27 +0000 (15:04 +0300)]
Staging: Pohmelfs: Drop ftrans debugging code.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Evgeniy Polyakov [Fri, 27 Mar 2009 12:04:26 +0000 (15:04 +0300)]
Staging: Pohmelfs: Use wait_on_page_timeout when waiting for remote directory sync instead of hardcoded 25 seconds.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Evgeniy Polyakov [Fri, 27 Mar 2009 12:04:25 +0000 (15:04 +0300)]
Staging: Pohmelfs: Reduce debugging noise about non-existing objects.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Evgeniy Polyakov [Fri, 27 Mar 2009 12:04:24 +0000 (15:04 +0300)]
Staging: Pohmelfs: Sync fs before killing it, since dentry cache is shrunk before writeback is invoked via generic_shutdown_super()
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Evgeniy Polyakov [Fri, 27 Mar 2009 12:04:23 +0000 (15:04 +0300)]
Staging: Pohmelfs: Extend remount option.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>