Jo-Philipp Wich [Thu, 20 Jun 2019 10:54:02 +0000 (12:54 +0200)]
procd: add direct dependencies on libblobmsg-json and libjson-c
The OpenWrt buildroot ABI version rebuild tracker does not handle
transient dependencies, therefor add all libraries linked by procd
as direct dependencies to the corresponding binary package definition.
This ensures that procd is automatically rebuilt and relinked
if any of these libraries has its ABI_VERSION updated in the
future.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Petr Štetiar [Thu, 20 Jun 2019 10:44:32 +0000 (12:44 +0200)]
ramips: fix EW-7478AC model name in DTS
This fixes lower case AC in the DTS model name.
Fixes: 88f7a29f99fb ("ramips: add support for Edimax EW-7476RPC / EW-7478AC")
Reported-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Yousong Zhou [Thu, 20 Jun 2019 08:22:44 +0000 (08:22 +0000)]
netsupport: add kmod-nsh
This is required by kmod-openvswitch since linux 4.15.
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
David Bauer [Tue, 18 Jun 2019 22:07:12 +0000 (00:07 +0200)]
ath79: correct various phy-mode properties
Upstream commit
6d4cd04 changes how the internal delays of the AR803x
based PHYs are enabled. With this commit, all internal delays are
disabled on driver probe and enabled based on the 'phy-mode' property in
the device-tree.
Before this commit, the RX delay was always enabled upon soft-reset
while the TX delay retained it's previous state. A hard reset enabled
the RX delay while the TX delay was disabled.
Because of this inconsistency, wrongly specified PHY-modes were working
correctly while the hardware was in a different state.
Fix the PHY-modes of some affected devices (and clean up misplaced
properties along the way) to keep the devices working flawlessly with
kernels >= 5.1.
Signed-off-by: David Bauer <mail@david-bauer.net>
Pawel Dembicki [Mon, 29 Oct 2018 20:50:13 +0000 (20:50 +0000)]
ramips: fix GELAN port in D-Link DWR-118-A2
This patch fix and enable GELAN port in D-LINK DWR-118-A2.
Tested-by: Richard Toth <trtk1992@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Pawel Dembicki [Mon, 29 Oct 2018 20:31:25 +0000 (20:31 +0000)]
ramips: mt7620: add EPHY base mdio address changing possibility
In some boards is requred to change the ephy mdio base address.
This patch add of property "mediatek,ephy-base-address" in gsw
part, which allows to change ephy base address.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[fixed indentation in header file]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Pawel Dembicki [Mon, 29 Oct 2018 17:30:22 +0000 (17:30 +0000)]
ramips: mt7620: fix external PHY autopolling
The port initialisation is based on assumption that phy address and
port number is the same. SoC allow different numbers and some board
have it.
Use phy address instead the port number to make sure that correct
addresses are polled.
In situation when only one PHY with address 0x0 is conected to
port 4, autopolling is broken.
This patch make autopolling correct when port number and phy address
are different.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Mathias Kresin [Tue, 17 Apr 2018 16:51:42 +0000 (18:51 +0200)]
ramips: handle mdio address and switch port seperate
The phy handling code forces a phy mdio address and the switch port to
which a phy is attached to be the same. Albeit such a configuration is
used for most boards, it isn't for all.
Pass the switch port number to the ethernet phy connect functions, to
ensure the correct list entry is edited and not the list entry that
matches th phys mdio address.
Use the mdio address with mdiobus_get_phy instead of the port number,
to make sure the expected ethernet phy gets connected.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Mathias Kresin [Wed, 4 Apr 2018 16:26:24 +0000 (18:26 +0200)]
ramips: ignore already handled ethernet phys
The whole logic in fe_phy_connect() is based on the asumption that mdio
address and switch port id are equal. Albeit it is true for most
boards, it doesn't is for all.
It isn't yet clear which subtargets/boards require the devicetree less
ethernet phy handling. Hence change the code in a way that it doesn't
touch ethernet phys which were early attached and are already handled.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Birger Koblitz [Tue, 18 Jun 2019 16:49:41 +0000 (18:49 +0200)]
ramips: add support for Edimax EW-7478APC
SoC: MediaTek MT7620a @ 580MHz
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 8MB (Macronix)
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
Switch: Mediatek MT7530W Gigabit Switch (4 x LAN, 1 x WAN)
USB: Yes 1 x 2.0 (+ 1 x 2.0 unpopulated header)
BTN: Reset/WPS
LED: - Power (white)
- Internet (blue)
- Wifi (blue)
- USB (blue)
UART: UART is present as Pads with throughholes on the PCB. They are
located in the lower right corner (GbE ports facing up)
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation
------------
Update the factory image via the web-interfaces (by default:
http://edimax.setup)
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[merge conflicts in 01_leds and mt7620.mk, dts whitespace issues]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Birger Koblitz [Mon, 3 Jun 2019 20:04:12 +0000 (22:04 +0200)]
ramips: add support for Edimax EW-7476RPC / EW-7478AC
SoC: MediaTek MT7620a @ 580MHz
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 8MB (Macronix)
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
GbE: 1x (RTL8211E)
BTN: WPS - RFKILL/RF 50%/RF 100% toggle
LED: - Wifi 5g (blue)
- Wifi 2g (blue)
- Crossband (green)
- Power (green)
- WPS (green)
- LAN (Green)
UART: UART is present as Pads with throughholes on the PCB. They are
located next to the switch for the wifi configuration
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation
------------
Update the factory image via the web-interfaces (by default:
192.168.9.2/24).
http://192.168.9.2/index.asp
ramips: add Edimax EW-7478AC
SoC: MediaTek MT7620a @ 580MHz
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 8MB (Macronix)
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
GbE: 1x (RTL8211E)
BTN: WPS - RFKILL/RF 50%/RF 100% toggle
LED: - Wifi 5g (blue)
- Wifi 2g (blue)
- Crossband (green)
- Power (green)
- WPS (green)
- LAN (Green)
UART: UART is present as Pads with throughholes on the PCB. They are
located next to the switch for the wifi configuration
3.3V - RX - GND - TX / 57600-8N1
3.3V is the square pad
Installation
------------
Update the factory image via the web-interfaces (by default:
http://edimaxext.setup)
Or push wpa button on power on and send firmware via tftp to 192.168.1.6
The EW-7478AC is identical to the EW-7476RPC, except instead of 2 internal
antennas it has 2 external ones.
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
[merge conflict in 01_leds]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Deng Qingfang [Tue, 30 Apr 2019 13:43:25 +0000 (21:43 +0800)]
libjson-c: update to 0.13.1
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
Vladimir Vid [Fri, 7 Jun 2019 13:50:50 +0000 (15:50 +0200)]
mvebu: fix regression for non-generic ESPRESSObin versions
When targets for multiple ESPRESSObin devices were added, not all
files were updated which means any ESPRESSObin version beside generic
won't have proper networking, sysupgrade and uboot-env. This patch
fixes the issue.
* fixup network detection
* fixup uboot-env
* fixup platform.sh for sysupgrade
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Vladimir Vid [Fri, 7 Jun 2019 13:58:15 +0000 (15:58 +0200)]
mvebu: image: fix generic-arm64.bootscript mmc selection
Not all versions of ESPRESSObin require SD card, but can
be booted from the internal emmc flash (mmc dev 1) instead.
Add a simple check in the bootscript to see which mmc device
is detected and boot from it using mmcdev variable.
Tested-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Petr Štetiar [Thu, 13 Jun 2019 11:48:27 +0000 (13:48 +0200)]
treewide: kernel: bump some targets to 4.19
Lets bump kernel to 4.19 on targets which were run tested or got ACKed
so we've enough time to make it ready for next release:
armvirt/32 (runtested in qemu)
armvirt/64 (runtested in qemu)
ath79/generic (runtested on Carambola2)
gemini/generic (runtested on DIR-685, DNS-313, SQ201, SL93512R)
imx6/generic (runtested on Apalis)
ipq40xx/generic (runtested on nbg6617)
malta/be64 (runtested in qemu)
malta/be (runtested in qemu)
malta/le (runtested in qemu)
malta/le64 (runtested in qemu)
mpc85xx/generic (runtested on TL-WDR4900)
mpc85xx/p2020 (runtested on P2020RDB)
mvebu/cortexa53
mvebu/cortexa72
mvebu/cortexa10
octeon/generic (runtested on EdgeRouter Lite)
sunxi/cortexa53 (build tested only)
sunxi/cortexa7 (runtested on Lime2-K)
sunxi/cortexa8 (build tested only)
tegra/generic
x86/64 (runtested in qemu)
Acked-by: Zoltan HERPAI <wigyori@uid0.hu> [sunxi]
Tested-by: Linus Walleij <linus.walleij@linaro.org> [gemini]
Tested-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [mvebu, tegra]
Tested-by: Daniel Engberg <daniel.engberg.lists@pyret.net> [octeon]
Tested-by: Pawel Dembicki <paweldembicki@gmail.com> [mpc85xx/generic mpc85xx/p2020]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Thu, 13 Jun 2019 22:26:44 +0000 (22:26 +0000)]
kernel: generic: add missing DRM panel 4.19 config symbols
While building tegra/generic on 4.19, I've discovered few missing
symbols related to DRM panel symbols.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Thu, 13 Jun 2019 12:34:59 +0000 (12:34 +0000)]
kernel: generic: add missing 4.19 config symbol
Fixes following kernel build issue on ath79/generic:
Enable support for latency based cgroup IO protection (BLK_CGROUP_IOLATENCY) [N/y/?] (NEW)
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Mon, 17 Jun 2019 05:27:46 +0000 (05:27 +0000)]
armvirt: refresh 4.19 kernel config
Refresh kernel configs with 4.19 bits, while at it, add common symbols
into the target config.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Sun, 16 Jun 2019 19:39:32 +0000 (19:39 +0000)]
armvirt: add kernel configs for 4.19
It's just copy of 4.14 and will be refreshed in the upcoming commit,
renamed config-default to config-4.14 as well.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Koen Vandeputte [Tue, 18 Jun 2019 11:19:59 +0000 (13:19 +0200)]
kernel: bump 4.19 to 4.19.52
Refreshed all patches.
Fixes:
- CVE-2019-11479
- CVE-2019-11478
- CVE-2019-11477
Also fix a malformed patch issue caught during refresh.
It was caused by removing a whitespace without altering
the index values in a patch which alters a patch.
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Fixes: cf6526249298 ("kernel: bump 4.19 to 4.19.51")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Tue, 18 Jun 2019 10:37:27 +0000 (12:37 +0200)]
kernel: bump 4.14 to 4.14.127
Refreshed all patches.
Fixes:
- CVE-2019-11479
- CVE-2019-11478
- CVE-2019-11477
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Tue, 18 Jun 2019 09:49:03 +0000 (11:49 +0200)]
kernel: bump 4.9 to 4.9.182
Refreshed all patches.
Fixes:
- CVE-2019-11479
- CVE-2019-11478
- CVE-2019-11477
Compile-tested on: none
Runtime-tested on: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 17 Jun 2019 11:31:05 +0000 (13:31 +0200)]
kernel: bump 4.19 to 4.19.51
Refreshed all patches.
Altered patches:
- 370-netfilter-nf_flow_table-fix-offloaded-connection-tim.patch
- 220-optimize_inlining.patch
- 640-netfilter-nf_flow_table-add-hardware-offload-support.patch
This patch also restores the initial implementation
of the ath79 perfcount IRQ issue. (
78ee6b1a40b5)
It was wrongfully backported upstream initially and got reverted now.
Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Koen Vandeputte [Mon, 17 Jun 2019 11:24:31 +0000 (13:24 +0200)]
kernel: bump 4.14 to 4.14.126
Refreshed all patches.
Altered patches:
- 220-optimize_inlining.patch
- 816-pcie-support-layerscape.patch
This patch also restores the initial implementation
of the ath79 perfcount IRQ issue. (
78ee6b1a40b5)
It was wrongfully backported upstream initially and got reverted now.
Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Petr Štetiar [Mon, 17 Jun 2019 13:25:40 +0000 (15:25 +0200)]
urngd: move project to git.openwrt.org
Let's move project to a proper place.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Thu, 13 Jun 2019 13:07:10 +0000 (15:07 +0200)]
ar71xx: make target source-only
Lets make it really explicit, that we should now focus only on ath79 in
order to make it ready for next release, where ar71xx is going to be
removed for good.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Henryk Heisig [Sat, 23 Mar 2019 08:35:11 +0000 (08:35 +0000)]
ar71xx: base-files: fix board detect on new MikroTik devices
Move all MikroTik devices to new function to increase script execution
speed.
Machine name in new version of MikroTik RouterBOARD devices add "RB"
before model name:
Old machine name: MikroTik RouterBOARD 951Ui-2nD
New: MikroTik RouterBOARD RB951Ui-2nD
So this patch should fix it for all currently supported MikroTik boards.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[rebased,commit message facelift,script fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[spotted missing 922UAGS-5HPacD]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Petr Štetiar [Sat, 15 Jun 2019 09:28:05 +0000 (09:28 +0000)]
gpio-button-hotplug: fix 4.19 build breakage on malta/be64
While testing 4.19 build on malta/be64, I've encountered following
error:
gpio-button-hotplug/gpio-button-hotplug.c:529:18: error: implicit
declaration of function 'gpio_to_desc'
which is caused by the missing include fixed by this patch.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Thu, 13 Jun 2019 22:38:22 +0000 (22:38 +0000)]
tegra: add missing kernel symbol to 4.19 config
This patch adds missing kernel config symbol to 4.19 kernel config.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Thu, 13 Jun 2019 22:32:46 +0000 (22:32 +0000)]
tegra: refresh 4.19 kernel config
This patch refreshes Tegra's 4.19 kernel config.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Marko Ratkaj [Thu, 13 Jun 2019 14:40:46 +0000 (16:40 +0200)]
mvebu: add kernel 4.19 support
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
[added sfp related patches from Russell King]
Signed-off-by: Marek Behún <marek.behun@nic.cz>
[rebase; rework patches; separate and cleanup kernel configs;
add espessobin dts; adjust venom dts]
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tomasz Maciej Nowak [Thu, 13 Jun 2019 14:40:47 +0000 (16:40 +0200)]
kernel: package module for SafeXcel crypto engine
Supports EIP97 and EIP197 found on Armada 37xx, 7k and 8k SoCs.
Unfortunately firmware for EIP197 is not easily obtainable, therefore
to not cause lot of user requests directed at OpenWrt, package it as
module with explanation where to obtain the firmware.
Cc: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Rafał Miłecki [Mon, 17 Jun 2019 04:53:07 +0000 (06:53 +0200)]
kernel: backport 4.18 patch adding DMI_PRODUCT_SKU
It's needed for applying some hardware quirks. This fixes:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/dmi.c:60:20: error: 'DMI_PRODUCT_SKU' undeclared here (not in a function); did you mean 'DMI_PRODUCT_UUID'?
DMI_EXACT_MATCH(DMI_PRODUCT_SKU, "T8"),
Fixes: 8888cb725d49 ("mac80211: brcm: backport remaining brcmfmac 5.2 patches")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Hauke Mehrtens [Sun, 16 Jun 2019 20:54:23 +0000 (22:54 +0200)]
uhttpd: Fix format string build problems
91fcac34ac uhttpd: Fix multiple format string problems
Fixes: fc454ca15305 libubox: update to latest git HEAD
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hans Dedecker [Sun, 16 Jun 2019 19:27:04 +0000 (21:27 +0200)]
nghttp2: bump to 1.39.1
7ffc239b Bump up version number to 1.39.1
bc886a0e Fix FPE with default backend
a3a14a9c Fix log-level is not set with cmd-line or configuration file
acfb3607 Update manual pages
bdfd14c2 Bump up version number to 1.39.0, LT revision to 31:4:17
cddc09fe Update AUTHORS
3c3b6ae8 Add missing colon
2f83aa9e Fix multi-line text travis issue
fc591d0c Run nghttpx integration test with cmake build
9a17c3ef travis: use multi-line text
b7220f07 cmake: Remove SPDY related files
a1556fd1 Merge pull request #1356 from nghttp2/fix-log-level-on-reload
77f1c872 nghttpx: Fix unchanged log level on configuration reload
49ce44e1 Merge pull request #1352 from nghttp2/travis-osx
f54b3ffc Fix libxml2 CFLAGS output
b0f5e5cc Implement daemon() using fork() for OSX
8d6ecd66 Enable osx build on travis
f82fb521 Update doc
2e1975dd clang-format-8
97ce392b Merge pull request #1347 from nghttp2/nghttpx-ignore-cl-te-on-upgrade
afefbda5 Ignore content-length in 200 response to CONNECT request
4fca2502 nghttpx: Ignore Content-Length and Transfer-Encoding in 1xx or 200 to CONNECT
6975c336 Update llhttp to 1.1.3
0288093c Fix llhttp_get_error_pos usage
a3a03481 Merge pull request #1340 from nghttp2/nghttpx-llhttp
c64d2573 Replace http-parser with llhttp
f028cc43 clang-format
302e3746 Merge pull request #1337 from nghttp2/upgrade-mruby
3cdbc5f5 Merge pull request #1335 from adamgolebiowski/boost-1.70
a6925186 Fix mruby build error
45d63d20 Upgrade mruby to 2.0.1
cbba1ebf asio: support boost-1.70
e86d1378 Bump up version number to 1.39.0-DEV
4a9d2005 Update manual pages
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Hauke Mehrtens [Sun, 16 Jun 2019 16:59:04 +0000 (18:59 +0200)]
urngd: Fix more wrong type in format string
Also the other type is worng and causes compile problems on ARM64
platforms.
Fixes: 9b53201d9c53 ("urngd: Fix wrong type in format string")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
George Amanakis [Thu, 13 Jun 2019 04:03:38 +0000 (00:03 -0400)]
mvebu: fixes commit
a7e68927d0
err_free_stats has been deprecated. Replace with err_netdev.
Compile-tested on: mvebu
Runtime-tested on: mvebu
Fixes: a7e68927d047 ("kernel: bump 4.14 to 4.14.125 (FS#2305 FS#2297)")
Signed-off-by: George Amanakis <gamanakis@gmail.com>
Rafał Miłecki [Sun, 16 Jun 2019 16:56:15 +0000 (18:56 +0200)]
mac80211: brcm: backport remaining brcmfmac 5.2 patches
This improves FullMAC firmware compatibility, adds logging in case of
firmware crash and *may* fix "Invalid packet id" errors.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Hauke Mehrtens [Sun, 12 May 2019 16:49:24 +0000 (18:49 +0200)]
kernel: Activate CONFIG_OPTIMIZE_INLINING
This will reduce the size of the kernel if CONFIG_CC_OPTIMIZE_FOR_SIZE is
set like for all targets with small_flash feature flag.
I haven't seen any changes for an ARM64 target which optimizes the
kernel for speed instead.
On the ath79/tiny target the uncompressed kernel size was reduced by
3.2% and the compressed kernel size by 2.1%
kernel size with CONFIG_OPTIMIZE_INLINING=n
4346412 build_dir/target-mips_24kc_musl/linux-ath79_tiny/vmlinux
1391169 build_dir/target-mips_24kc_musl/linux-ath79_tiny/tplink_tl-wr941-v4-kernel.bin
Kernel size with CONFIG_OPTIMIZE_INLINING=y
4212396 build_dir/target-mips_24kc_musl/linux-ath79_tiny/vmlinux
1362051 build_dir/target-mips_24kc_musl/linux-ath79_tiny/tplink_tl-wr941-v4-kernel.bin
This change is currently pending for kernel 5.2 and already in
linux-next, this updates our patch to match the upstream version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
André Valentin [Fri, 14 Jun 2019 11:09:46 +0000 (13:09 +0200)]
netsupport: improve xfrm module support
-switch to module autoprobe
-exclude 4.9 kernel
Signed-off-by: André Valentin <avalentin@marcant.net>
Hauke Mehrtens [Sun, 16 Jun 2019 14:36:13 +0000 (16:36 +0200)]
libubox: update to latest git HEAD
9dd2dcf libubox: add format string checking to ulog()
ecf5617 ustream: Add format string checks to ustream_(v)printf()
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Joseph Benden [Wed, 8 May 2019 18:52:56 +0000 (11:52 -0700)]
toolchain: Add GCC 9.1.0 release
Most of the patches are copied over from GCC 8.3.
The following patches are backported from the GCC 9.X development branch:
toolchain/gcc/patches/9.1.0/970-recompute-dom-fast-queries-before-vn.patch
toolchain/gcc/patches/9.1.0/975-g++-ICE-with-generic-lambda.patch
The specs file changed with gcc 9, now it contains "%@{L*}" instead of
"%{L*}" in older GCC versions.
Signed-off-by: Joseph Benden <joe@benden.us>
Hauke Mehrtens [Sun, 16 Jun 2019 14:38:56 +0000 (16:38 +0200)]
urngd: Fix wrong type in format string
GCC 9.1 complains about this wrong type used in the format string, fix
this to make the compiler happy.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Sun, 16 Jun 2019 13:48:44 +0000 (15:48 +0200)]
ubox: bump to git HEAD
4df34a4 kmodloader: Increase path array size to make it always fit
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hans Dedecker [Sat, 15 Jun 2019 19:25:03 +0000 (21:25 +0200)]
netifd: xfrm fixes
9932ed0 netifd: fix xfrm interface deletion and standardize netlink call
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Adrian Schmutzler [Wed, 17 Apr 2019 13:45:52 +0000 (15:45 +0200)]
ath79: Add SUPPORTED_DEVICES for Archer C7 v1/v2
The identifier for both devices is "archer-c7" on ar71xx, set here:
https://github.com/openwrt/openwrt/blob/master/target/linux/ar71xx/base-files/lib/ar71xx.sh#L348
https://github.com/openwrt/openwrt/blob/master/target/linux/ar71xx/base-files/lib/ar71xx.sh#L511
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Christian Lamparter [Sat, 15 Jun 2019 17:51:28 +0000 (19:51 +0200)]
mac80211: refresh patches
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Sven Eckelmann [Tue, 11 Jun 2019 12:53:12 +0000 (14:53 +0200)]
mac80211: ath10k: adjust tx power reduction for US regulatory domain
FCC allows maximum antenna gain of 6 dBi. 15.247(b)(4):
> (4) The conducted output power limit
> specified in paragraph (b) of this section
> is based on the use of antennas
> with directional gains that do not exceed
> 6 dBi. Except as shown in paragraph
> (c) of this section, if transmitting
> antennas of directional gain greater
> than 6 dBi are used, the conducted
> output power from the intentional radiator
> shall be reduced below the stated
> values in paragraphs (b)(1), (b)(2),
> and (b)(3) of this section, as appropriate,
> by the amount in dB that the
> directional gain of the antenna exceeds
> 6 dBi.
https://www.gpo.gov/fdsys/pkg/CFR-2013-title47-vol1/pdf/CFR-2013-title47-vol1-sec15-247.pdf
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Sven Eckelmann [Tue, 11 Jun 2019 12:53:12 +0000 (14:53 +0200)]
mac80211: ath10k: fix max antenna gain unit
Most of the txpower for the ath10k firmware is stored as twicepower (0.5 dB
steps). This isn't the case for max_antenna_gain - which is still expected
by the firmware as dB.
The firmware is converting it from dB to the internal (twicepower)
representation when it calculates the limits of a channel. This can be seen
in tpc_stats when configuring "12" as max_antenna_gain. Instead of the
expected 12 (6 dB), the tpc_stats shows 24 (12 dB).
Tested on QCA9888 and IPQ4019 with firmware 10.4-3.5.3-00057.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Sven Eckelmann [Tue, 11 Jun 2019 12:46:28 +0000 (14:46 +0200)]
mac80211: ath9k: Increase allowed antenna gain to 6 dBi
FCC allows maximum antenna gain of 6 dBi. 15.247(b)(4):
> (4) The conducted output power limit
> specified in paragraph (b) of this section
> is based on the use of antennas
> with directional gains that do not exceed
> 6 dBi. Except as shown in paragraph
> (c) of this section, if transmitting
> antennas of directional gain greater
> than 6 dBi are used, the conducted
> output power from the intentional radiator
> shall be reduced below the stated
> values in paragraphs (b)(1), (b)(2),
> and (b)(3) of this section, as appropriate,
> by the amount in dB that the
> directional gain of the antenna exceeds
> 6 dBi.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Pavel Kubelun [Tue, 14 May 2019 13:42:19 +0000 (16:42 +0300)]
ipq40xx: fix high resolution timer
Cherry-picked from CAF QSDK repo.
see 090-ipq40xx-fix-high-resolution-timer.patch
Original commit message:
The kernel is failing in switching the timer for high resolution
mode and clock source operates in 10ms resolution. The always-on
property needs to be given for timer device tree node to make
clock source working in 1ns resolution.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[changed authorship of main patch to pavel and cherry-picked
patch to Abhishek Sahu]
Pavel Kubelun [Tue, 14 May 2019 13:42:17 +0000 (16:42 +0300)]
ipq40xx: directly define voltage per opp
This should align opp table with what it was before converting to OPP v2.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Mantas Pucka [Tue, 11 Jun 2019 14:08:48 +0000 (17:08 +0300)]
kernel: mt29f_spinand: fix memory leak during page program
Memory is allocated with devm_kzalloc() on every page program
and leaks until device is closed (which never happens).
Convert to kzalloc() and handle error paths manually.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Adrian Schmutzler [Tue, 11 Jun 2019 11:28:02 +0000 (13:28 +0200)]
ath79: Merge cases in 11-ath10k-caldata
Cosmetical patch that just merges two cases.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Christian Lamparter [Fri, 14 Jun 2019 22:45:58 +0000 (00:45 +0200)]
iwinfo: update PKG_MIRROR_HASH
This patch updates the PKG_MIRROR_HASH to match the one
of the current version.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Linus Walleij [Tue, 11 Jun 2019 21:25:39 +0000 (23:25 +0200)]
gemini: Make root filesystem writeable
The squashfs+jffs2 root filesystem only came up as read-only
and the config would not take:
[ 25.600237] mount_root: Could not open mtd device: /dev/mtd4
[ 25.634674] mount_root: reading rootfs_data failed
[ 25.665346] mount_root: Could not open mtd device: /dev/mtd3
[ 25.699802] mount_root: reading rootfs failed
[ 25.726426] mount_root: mounting /dev/root
Well that is not very strange since the whole firmware partition
is made read-only in the device tree. Let's fix that by augmenting
the OpenWrt patch.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Tue, 11 Jun 2019 21:06:55 +0000 (23:06 +0200)]
gemini: Fix MAC address assignment for DIR-685
The DIR-685 has the MAC addresses in the RedBoot code just like
DNS-313. Check some magic numbers to determine that the MAC
address is where we want it and extract it from RedBoot.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[replaced ifconfig with ip, ! -z = -n, added string quotes]
Linus Walleij [Tue, 11 Jun 2019 21:06:54 +0000 (23:06 +0200)]
gemini: Make a per-board case for ethernet MAC
The DNS-313 isn't the only special board so let's bite the
bullet and create a case ladder in preparation for DIR-685.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [refreshed]
Linus Walleij [Tue, 11 Jun 2019 21:06:53 +0000 (23:06 +0200)]
gemini: Use library functions to assign MAC address
This simplifies the ethernet address extraction script
by using standard library functions to locate the MTD
partitions and extract ethernet address from a binary
offset location in the flash. Furthermore, the aging
ifconfig is replaced by the ip tool, which will now
assign the MAC addresses.
Suggested-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[ifconfig replacement, use -n instead of ! -z,
-n requires string to be quoted within the test brackets,
drop prepended "x" in check, add quotes, make local
variables local, kill whitespaces]
Christian Lamparter [Fri, 14 Jun 2019 16:44:51 +0000 (18:44 +0200)]
gemini: enable CONFIG_PACKET
CONFIG_PACKET is a important feature to have.
The Packet protocol is used by applications which
communicate directly with network devices without
an intermediate network protocol implemented in
the kernel, e.g. tcpdump and ip.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Rosen Penev [Mon, 20 May 2019 18:11:49 +0000 (11:11 -0700)]
kernel: Add AEAD and RNG support to kmod-crypto-user
Now that kernel 3.18 is gone, we can safely add these features.
Tested on Turris Omnia.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Hannu Nyman [Sat, 15 Jun 2019 09:16:55 +0000 (12:16 +0300)]
busybox: update to 1.31.0
* Update busybox to version 1.31.0.
New applets: ts, i2ctransfer
New (restored) feature: error/info levels in syslog messages.
Leave new features disabled by default.
* Refresh patches
* Remove patch that was backported from upstream
Config refreshed with commands below, after which the OpenWrt specific
config defaults (ipv6, login session child) were corrected:
make package/busybox/compile (to populate the build_dir)
cd package/utils/busybox/config/
../convert_menuconfig.pl ../../../../build_dir/target-mips_24kc_musl/busybox-1.31.0
cd package/utils/busybox
./convert_defaults.pl < ../../../build_dir/target-mips_24kc_musl/busybox-1.31.0/.config > Config-defaults.in
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
André Valentin [Fri, 14 Jun 2019 11:09:47 +0000 (13:09 +0200)]
network/config/xfrm: add host-dependency for xfrm interface parent
Add proto_add_host_dependency to add a dependency to the tunlink interface
Signed-off-by: André Valentin <avalentin@marcant.net>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
Yousong Zhou [Fri, 14 Jun 2019 01:49:42 +0000 (01:49 +0000)]
busybox: strip off ALTERNATIVES spec
Now that busybox is a known alternatives provider by opkg, we remove the
ALTERNATIVES spec and add a note to make the implicit situation clear
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Yousong Zhou [Fri, 14 Jun 2019 01:44:15 +0000 (01:44 +0000)]
opkg: bump to version 2019-06-14
Opkg starting from this version special-cases busybox as alternatives
provider. There should be no need to add entries to ALTERNATIVES of
busybox package
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Stijn Tintel [Thu, 13 Jun 2019 22:18:58 +0000 (01:18 +0300)]
kernel: add missing symbol to 4.19 config
Kernel 4.19.47 added a new kernel config symbol ARM64_ERRATUM_1463225.
This causes a build failure for sunxi/cortexa53. Add the symbol to the
generic config to fix this, and avoid future build failures on other
arm64 targets that expose this symbol. As the erratum only affects
Cortex-A76 cores, we can safely disable it.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Hans Dedecker [Thu, 13 Jun 2019 20:16:06 +0000 (22:16 +0200)]
netifd: update to latest git HEAD
42a3878 interface-ip: fix possible null pointer dereference
c1964d8 system-linux: remove superfluous dev check
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Kevin Darbyshire-Bryant [Thu, 13 Jun 2019 16:34:26 +0000 (17:34 +0100)]
ath10k-firmware: update Candela Tech firmware images
wave-1:
2019-05-09: Tweak rate-ctrl: Ramp PER up faster, down slower. This
helps throughput in rate-vs-range test, especially with
nss1.
2019-05-20: Disable adaptive-CCA. I am not sure it helps, and it may
make it slower to detect noise that should tell the system
to stop transmitting. If someone has means to test this
properly, I'd be happy to work with them.
wave-2:
2019-05-15: Fix problem where rate-ctrl sometimes used rix of 0x0.
2019-05-15: Allow raw-tx of encrypted frame. Requires a patch to the
driver to use raw mode when skb has WEP flag enabled AND
skb is flagged to not be encrypted. Lightly tested.
2019-05-16: Fix tx-hang that happened when rate-ctrl chose an OFDM rate
for 20Mhz and sent that as AMPDU. To fix, limit to (V)HT
rates if peer is (V)HT. It seems that MCS0 (V)HT20 should
have as good of a chance of being detected as CCK or OFDM.
2019-06-06: Disable TX-BFEE, TX-BFER for IBSS connections. I suspect
this is part of the tx-hang issue seen with IBSS between
two 9984 radios.
2019-06-12: Fix rx-rate reporting in 'fw_stats' logic. This was at
least partly due to regressions I had added earlier when
working on some multi-vdev enhancements.
2019-6-12: Fix case where extd peer-stats were not always populated.
The stats gathering code did not handle error conditions
well.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Kevin Darbyshire-Bryant [Thu, 13 Jun 2019 18:06:25 +0000 (19:06 +0100)]
ath10k-ct: Update to 2019-06-13
Changes:
ath10k: Improve PMF/MPF mgt frame check
And add a driver for 5.2 (beta, not even tested yet) kernel.
Refresh patches.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Paul Spooren [Wed, 12 Jun 2019 21:38:20 +0000 (23:38 +0200)]
f2fs-tools: fixup SPDX license
The f2fs-tools have a wrong PKG_LICENSE with is not SPDX compatible.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Daniel Golle [Sat, 29 Dec 2018 05:51:32 +0000 (06:51 +0100)]
config: enable some useful features on !SMALL_FLASH devices
enable kernel features needed for procd-ujail, procd-seccomp, lxc and
more on devices with big enough flash. Those packages are currently
useless in binary builds due to missing kernel features.
Enable the features on devices which can bare with the extra space
consumption.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Konstantin Demin [Wed, 12 Jun 2019 09:10:09 +0000 (12:10 +0300)]
nghttp2: deduplicate files in libnghttp2
libnghttp2 accidentally ships library twice:
$ tar -Oxzf libnghttp2-14_1.38.0-1_mips_24kc.ipk ./data.tar.gz | tar -tzvf -
drwxr-xr-x root/root 0 2019-06-07 23:14 ./
drwxr-xr-x root/root 0 2019-06-07 23:14 ./usr/
drwxr-xr-x root/root 0 2019-06-07 23:14 ./usr/lib/
-rw-r--r-- root/root 144412 2019-06-07 23:14 ./usr/lib/libnghttp2.so.14
-rw-r--r-- root/root 144412 2019-06-07 23:14 ./usr/lib/libnghttp2.so.14.17.3
after fix, there's library and symlink (as designed):
$ tar -Oxzf libnghttp2-14_1.38.0-2_mips_24kc.ipk ./data.tar.gz | tar -tzvf -
drwxr-xr-x root/root 0 2019-06-07 23:14 ./
drwxr-xr-x root/root 0 2019-06-07 23:14 ./usr/
drwxr-xr-x root/root 0 2019-06-07 23:14 ./usr/lib/
lrwxrwxrwx root/root 0 2019-06-07 23:14 ./usr/lib/libnghttp2.so.14 -> libnghttp2.so.14.17.3
-rw-r--r-- root/root 144412 2019-06-07 23:14 ./usr/lib/libnghttp2.so.14.17.3
Binary package size reduced accordingly: 134621 -> 66593.
Compile/run-tested: ar71xx/generic.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Koen Vandeputte [Wed, 12 Jun 2019 12:41:51 +0000 (14:41 +0200)]
iwinfo: update to latest git HEAD
1372f47eff34 iwinfo: Add Mikrotik R11e-5HnDr2
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Tue, 11 Jun 2019 16:26:06 +0000 (18:26 +0200)]
kernel: bump 4.19 to 4.19.50
Refreshed all patches.
Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Tue, 11 Jun 2019 16:25:36 +0000 (18:25 +0200)]
kernel: bump 4.14 to 4.14.125 (FS#2305 FS#2297)
Refreshed all patches.
This bump contains upstream commits which seem to avoid (not properly fix)
the errors as seen in FS#2305 and FS#2297
Altered patches:
- 403-net-mvneta-convert-to-phylink.patch
- 410-sfp-hack-allow-marvell-10G-phy-support-to-use-SFP.patch
Compile-tested on: ar71xx, cns3xxx, imx6, mvebu, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Tue, 11 Jun 2019 16:22:19 +0000 (18:22 +0200)]
kernel: bump 4.9 to 4.9.181
Refreshed all patches.
Compile-tested on: ar7
Runtime-tested on: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Yousong Zhou [Tue, 11 Jun 2019 08:26:27 +0000 (08:26 +0000)]
dnsmasq: move feature detection inside a shell func
Resolves openwrt/packages#9219
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Petr Štetiar [Mon, 20 May 2019 14:47:23 +0000 (16:47 +0200)]
build: add urandom-seed and urngd to default packages set
urandom-seed content was split from base-files into separate package so
in order to preserve the current functionality and to provide some
fallback mechanism in case jent-rng initialization fails in urngd we
need to add it back.
urngd is OpenWrt's micro non-physical true random number generator based
on timing jitter.
Tested-by: Lucian Cristian <lucian.cristian@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Mon, 20 May 2019 14:38:33 +0000 (16:38 +0200)]
base-files: move urandom seed bits into separate package
So it's possible to install or remove it as needed.
Tested-by: Lucian Cristian <lucian.cristian@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Mon, 20 May 2019 14:41:43 +0000 (16:41 +0200)]
ubox: move getrandom into separate getrandom package
So it's possible to install or remove it as needed.
Tested-by: Lucian Cristian <lucian.cristian@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Mon, 20 May 2019 12:02:20 +0000 (14:02 +0200)]
urng: add micro non-physical true RNG based on timing jitter
μrngd is OpenWrt's micro non-physical true random number generator based
on timing jitter.
Using the Jitter RNG core, the rngd provides an entropy source that
feeds into the Linux /dev/random device if its entropy runs low. It
updates the /dev/random entropy estimator such that the newly provided
entropy unblocks /dev/random.
The seeding of /dev/random also ensures that /dev/urandom benefits from
entropy. Especially during boot time, when the entropy of Linux is low,
the Jitter RNGd provides a source of sufficient entropy.
Tested-by: Lucian Cristian <lucian.cristian@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Alexander Couzens [Mon, 10 Jun 2019 23:49:30 +0000 (01:49 +0200)]
version.mk: use https:// instead of http://
Only the repo should not use https. Otherwise the build would need
a wget/uclient_fetch with tls support.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Alexander Couzens [Mon, 10 Jun 2019 23:38:46 +0000 (01:38 +0200)]
replace links towards lede-project.org with openwrt.org
Modify VERSION_SUPPORT_URL VERSION_REPO
Replace BUGS variable in toolchain/gcc/common.mk
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Karl Pálsson [Wed, 5 Jun 2019 17:16:52 +0000 (17:16 +0000)]
toolchain: replace LEDE in help text
Use generic wording.
Signed-off-by: Karl Pálsson <karlp@etactica.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [fixed a -> á]
Kristian Evensen [Thu, 6 Jun 2019 16:27:39 +0000 (18:27 +0200)]
ramips: Remove redundant LED-cases
01_leds has several redundant LED-cases. This commit cleans
up the file by merging these cases into shared cases.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Adrian Schmutzler [Thu, 9 May 2019 12:55:16 +0000 (14:55 +0200)]
ath79: Add support for TP-Link Archer C25 v1
The TP-Link Archer C25 is a low-cost dual-band router.
Specification:
- CPU: Atheros QCA9561 775 MHz
- RAM: 64 MB
- Flash: 8 MB
- Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887
- NET: 5x 10/100 Mbps Ethernet
Some LEDs are controlled by an additional 74HC595 chip, but not
all of them as e.g. for the C59.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Wed, 5 Jun 2019 11:50:21 +0000 (13:50 +0200)]
ath79: Reorder some TP-Link Archer devices in 01_leds
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Deng Qingfang [Fri, 7 Jun 2019 16:40:32 +0000 (00:40 +0800)]
ramips: mt7620: select kmod-rt2800-pci driver for RT5592
ASUS RP-N53 and Buffalo WHR-600D use RT5592 for 5GHz wireless
After commit
367813b9b17 the driver for RT5592 (rt2800pci)
is not selected by default anymore, which broke their 5GHz wireless
Add it back to device packages
Fixes: 367813b9b17 ("ramips: mt7620: fix dependencies")
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
David Santamaría Rogado [Tue, 4 Jun 2019 20:06:17 +0000 (22:06 +0200)]
ath79: migrate Archer C7 5GHz radio device paths
When upgrading a TP-Link Archer C7 v2 from ar71xx to ath79,
the 5ghz radio stops working because the device path changed.
Some people subtitute the unsupported QCA9880v1 in the Archer v1
with supported QCA9880v2 radio. Since the stock radio doesn't
work, so it's safe to apply the change also for the Archer v1
images as well.
Also this patch renames the migration file and variables from
wmac to wifi.
Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[removed comment, added return 0 (not that it matters since uci is
clever, see 00-wmac-migration thread), reworded commit message]
Adrian Schmutzler [Wed, 5 Jun 2019 13:59:30 +0000 (15:59 +0200)]
ath79: Consistently label art partition with lower case
This patch harmonizes the label and alias for art partitions
across ath79. Since lower case seems to be more frequent, use that
consistently.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Wed, 5 Jun 2019 13:31:32 +0000 (15:31 +0200)]
ath79: Read MAC addresses from flash in 11-ath10k-caldata
In commit
c3a8518 eth0 and eth1 have been swapped for some devices,
but 11-ath10k-caldata has not been updated.
Instead of fixing this by swapping eth0/eth1, this patch will read
addresses from flash (as done for several devices already) so
adjustments due to eth order become obsolete.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Wed, 5 Jun 2019 13:17:01 +0000 (15:17 +0200)]
ath79: Consistently label info partition
The info/product-info partition, which frequently contains MAC
adresses, is typically assigned the 'info' alias in DTS, but
then labelled with 'info', 'product-info' or 'config'.
This leads to different aliases if used for setting MAC adresses
in DTS compared to when using e.g. mtd_get_mac_binary. Occationally,
also multiple switch-case entries are used just because of different
labelling.
This patch relabels those partitions in ath79 to consistently use
'info'.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Pawel Dembicki [Thu, 23 May 2019 18:41:50 +0000 (20:41 +0200)]
mpc85xx: re-enable TL-WDR4900v1 images
This reverts commit
324e94f31bfd ("mpc85xx: disable bricking TL-WDR4900v1 images")
The previous commit fixes the TL-WDR4900v1. Enable the target again.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Tue, 29 Jan 2019 22:52:27 +0000 (23:52 +0100)]
mpc85xx: convert TL-WDR4900 v1 to simpleImage
Converts the TP-Link WDR4900 v1 to use the simpleImage in the
hopes of prolonging the life of the device. While at it,
the patch makes the fdt.bin an ARTIFACT and sets the KERNEL_SIZE
to 2684 KiB as a precaution since the stock u-boot is using a
fixed kernel size.
Note: Give the image some time, it will take much longer to
extract and boot.
[tested for 4.14/4.19]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Co-authored-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
André Valentin [Sat, 8 Jun 2019 11:48:08 +0000 (13:48 +0200)]
config: add xfrm interface support scripts
This package adds scripts for xfrm interfaces support.
Example configuration via /etc/config/network:
config interface 'xfrm0'
option proto 'xfrm'
option mtu '1300'
option zone 'VPN'
option tunlink 'wan'
option ifid 30
config interface 'xfrm0_static'
option proto 'static'
option ifname '@xfrm0'
option ip6addr 'fe80::1/64'
option ipaddr '10.0.0.1/30'
Now set in strongswan IPsec policy:
if_id_in = 30
if_id_out = 30
Signed-off-by: André Valentin <avalentin@marcant.net>
Hans Dedecker [Mon, 10 Jun 2019 08:02:39 +0000 (10:02 +0200)]
curl: update to 7.65.1
For changes in 7.65.1; see https://curl.haxx.se/changes.html#7_65_1
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
André Valentin [Sat, 8 Jun 2019 11:48:07 +0000 (13:48 +0200)]
netsupport: add xfrmi interface support
Add support for xfrm interfaces in kernel. XFRM interfaces are used by
the IPsec stack for tunneling.
XFRM interfaces are available since linux 4.19.
Signed-off-by: André Valentin <avalentin@marcant.net>
Petr Štetiar [Wed, 5 Jun 2019 09:25:44 +0000 (11:25 +0200)]
kirkwood: image: fix unwanted 2nd inclusion of kernel
In commit
d2e18dae2892 ("kirkwood: cleanup image build code") the image
build code was refactored, setting KERNEL_IN_UBI=0 which doesn't work as
the KERNEL_IN_UBI needs to be unset in order to make it working as
intended, which leads to factory images with two kernels in them:
binwalk --keep-going openwrt-kirkwood-cisco_on100-squashfs-factory.bin
MD5 Checksum:
c33e3d1eb0cb632bf0a4dc287592eb70
DECIMAL HEX DESCRIPTION
-------------------------------------------------------------------------------
0 0x0 uImage header [...] "ARM OpenWrt Linux-4.14.123"
5769216 0x580800 uImage header [...] "ARM OpenWrt Linux-4.14.123"
Cc: Mathias Kresin <dev@kresin.me>
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=2285
Fixes: d2e18dae2892 ("kirkwood: cleanup image build code")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Tue, 4 Jun 2019 11:14:41 +0000 (13:14 +0200)]
gpio-button-hotplug: gpio-keys: fix always missing first event
Commit
afc056d7dc83 ("gpio-button-hotplug: support interrupt
properties") changed the gpio-keys interrupt handling logic in a way,
that it always misses first event, which causes issues with rc.button
scripts, so this patch restores the previous behaviour.
Fixes: afc056d7dc83 ("gpio-button-hotplug: support interrupt properties")
Reported-by: Kristian Evensen <kristian.evensen@gmail.com>
Tested-by: Kuan-Yi Li <kyli.tw@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [drop state check]
Petr Štetiar [Mon, 3 Jun 2019 21:08:01 +0000 (23:08 +0200)]
gpio-button-hotplug: fix wrong initial seen value
Currently the generated event contains wrong seen value, when the button
is pressed for the first time:
rmmod gpio_button_hotplug; modprobe gpio_button_hotplug
[ pressing the wps key immediately after modprobe ]
gpio-keys: create event, name=wps, seen=1088, pressed=1
So this patch adds a check for this corner case and makes seen=0 if the
button is pressed for the first time.
Tested-by: Kuan-Yi Li <kyli.tw@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
projects / openwrt / staging / xback.git / log