Mohammed Shafi Shajakhan [Fri, 22 Apr 2011 11:57:01 +0000 (17:27 +0530)]
ath9k: Add TSFOOR interrupt stats in debug info
This helped the developers to fix an issue of chip not entering network
sleep during idle state, previously this was only available as a debug
message
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Fri, 22 Apr 2011 07:42:23 +0000 (13:12 +0530)]
ath9k: remove the unlikely check for autosleep
newer chipsets support auto sleep feature, so remove the
unlikely check which does not seems to help anything
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Senthil Balasubramanian [Fri, 22 Apr 2011 06:02:12 +0000 (11:32 +0530)]
ath9k: Add power save wrappers and modularize hw_pll handler
We should protect hw_pll handler with power save wrappers and
also modularize hw_pll handler properly for better readability.
Also add a debug message to track chip resets on pll hang condition.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Senthil Balasubramanian [Fri, 22 Apr 2011 06:02:11 +0000 (11:32 +0530)]
ath9k: cleanup hw pll work handler
There is no reason why pll work handler should be part of xmit
file. move it to main.c so that reading hw check routines are
all in the same place.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Senthil Balasubramanian [Fri, 22 Apr 2011 06:02:10 +0000 (11:32 +0530)]
ath9k: optimize the usage of power save wrappers.
We need not wake up the chip even before mutex lock is acquired and also
that it is required only if we are going to drain the txq. So place the
wrappers accordingly and this change is also useful when there are no
pending frames in the txq as we do not wake up the chip unnecessarily.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Senthil Balasubramanian [Fri, 22 Apr 2011 06:02:09 +0000 (11:32 +0530)]
ath9k_hw: Fix incorrect baseband PLL phase shift for AR9485
we should program the AR9485 baseband PLL phase shift to 6 and
a redundant setting overwrites the correct value. Remove the
incorrect and unwnated register setting.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Senthil Balasubramanian [Fri, 22 Apr 2011 06:02:08 +0000 (11:32 +0530)]
ath9k: Fix LED gpio for AR93xx chipsets.
The LED gpio is incorrectly programmed for AR9300 and so the led
is not working propelry. AR93xx uses gpio 10 for LED and not the
default.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Thu, 21 Apr 2011 21:10:27 +0000 (14:10 -0700)]
cfg80211: module_param to disable HT40 in 2.4GHz band
Currently mac80211 uses ieee80211_disable_40mhz_24ghz module
parameter to allow disabling 40MHz operation in the 2.4GHz band.
Move this handling from mac80211 to cfg80211 so that the feature
will be more generic.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Thu, 21 Apr 2011 13:03:28 +0000 (18:33 +0530)]
ath9k: Fix warning: symbol 'ath9k_platform_id_table' was not declared. Should it be static?
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Thu, 21 Apr 2011 13:03:27 +0000 (18:33 +0530)]
ath9k: Fix bug in configuring hw timer
Hw next tigger time is configured as current_tsf + (timer_period * 10) which
is wrong, it should be current_tsf + timer_period. The wrong hw timer configuration
would cause btcoex related issues.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 21 Apr 2011 11:38:00 +0000 (13:38 +0200)]
mac80211: tear down BA sessions properly on suspend
Currently, the code to tear down BA sessions will
execute after queues are stopped, but attempt to
send frames, so those frames will just get queued,
which isn't intended. Move this code to before to
tear down the sessions properly.
Additionally, after stopping queues, flush the TX
queues in the driver driver to make sure all the
frames went out.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nishant Sarmukadam [Thu, 21 Apr 2011 11:04:59 +0000 (16:34 +0530)]
mwl8k: Enable life time expiry for tx packets in the hardware
Tell the firmware to enable the life time expiry of tx packets
in the hardware. The hardware will now refer to the timestamp
in every tx packet and decide whether the packet needs to be
dropped or transmitted.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nishant Sarmukadam [Thu, 21 Apr 2011 11:04:58 +0000 (16:34 +0530)]
mwl8k: Reserve buffers for tx management frames
Since queues are not stopped anymore, management frames would be
dropped if the corresponding tx queue is full.
This can cause issues say when we want to setup an ampdu stream and
action frames i.e addba requests keep getting dropped frequently.
Fix this by reserving some buffers to allow management frames to
go through in queue full conditions.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pradeep Nemavat [Thu, 21 Apr 2011 11:04:57 +0000 (16:34 +0530)]
mwl8k: Add timestamp information for tx packets
Timestamp tx packets using a HW micro-second timer.
This timestamp will be compared to the current timestamp
in the hardware and if the difference is greater than 500ms,
the packet will be dropped.
Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pradeep Nemavat [Thu, 21 Apr 2011 11:04:56 +0000 (16:34 +0530)]
mwl8k: Do not stop tx queues
This is in preparation to support life time expiry of packets in the
hardware to avoid head-of-line blocking where a slow client can
hog a tx queue and affect the traffic to a faster client from the same
queue. Time stamp the packets in driver to allow dropping them in the
hardware if they are queued for more than 500ms.
If queues are stopped, packets will be queued up outside the driver.
Since we will be able to timestamp the packets only after they hit the
driver, the timestamp will be less accurate since we cannot consider
the time the packets spent in queues outside the driver. With this commit,
to achieve accurate timestamping, the tx queues will not be stopped in
normal conditions. The only scenarios where the queues will be stopped are
when firmware commands are executing or if the interface is brought down.
Now, we need to be prepared for a situation where packets hit the driver
even after the tx queues are full. Drop all such packets in the driver itself.
Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanislaw Gruszka [Wed, 20 Apr 2011 14:02:58 +0000 (16:02 +0200)]
iwlwifi: fix possible data overwrite in hcmd callback
My commit
3598e1774c94e55c71b585340e7dc4538f310e3f
"iwlwifi: fix enqueue hcmd race conditions" move hcmd callback after
command queue reclaim, to avoid call it with hcmd_lock. But since
queue read index was updated, cmd data can be overwritten. Fix problem
by calling callback before taking hcmd_lock and queue reclaim.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Wed, 20 Apr 2011 09:12:30 +0000 (11:12 +0200)]
ssb: cc: add & fix defines
We probably got false positive results for checking PLL being down.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Wed, 20 Apr 2011 05:31:25 +0000 (11:01 +0530)]
ath9k_htc: Remove unused macros and structures
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Wed, 20 Apr 2011 05:31:10 +0000 (11:01 +0530)]
ath9k_htc: Use power save wrappers when accessing HW
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Wed, 20 Apr 2011 05:31:00 +0000 (11:01 +0530)]
ath9k_htc: Fix max A-MPDU size handling
Set the maximum ampdu size of a station correctly
in the target by using the ampdu_factor.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Wed, 20 Apr 2011 09:03:28 +0000 (14:33 +0530)]
ath9k_htc: Fix AMPDU subframe handling
* Register the driver's maximum ampdu subframe limit to mac80211.
* Cleanup the target capabilities structure and fix an endian issue.
* Fix BTCOEX by sending a command to the target when the BT priority
changes.
* Bump the required firmware version to 1.1
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan [Wed, 20 Apr 2011 05:30:34 +0000 (11:00 +0530)]
ath9k: Fix warnings from -Wunused-but-set-variable
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Tue, 19 Apr 2011 20:40:23 +0000 (22:40 +0200)]
ssb: cc: use correct min_msk for 0x4312
Default min_msk on my 0x4312 is 0x80000CBB, not 0xCBB. Now we follow
specs and wl (noticed in MMIO dumps).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Tue, 19 Apr 2011 20:40:22 +0000 (22:40 +0200)]
ssb: pci: trivial: correct amount of maximum retries
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Tue, 19 Apr 2011 13:59:20 +0000 (19:29 +0530)]
ath9k_hw: Enable AR9340 support
AR9340 is a AR9003 family built-in 2x2 wmac of ar934x SOCs. It is single band
in ar9341 SOC and dual band in ar9344/ar9342 SOCs.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Tue, 19 Apr 2011 13:59:19 +0000 (19:29 +0530)]
ath9k_hw: Disable INTR_HOST1_FATAL to avoid interrupt strom with ar9430
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Tue, 19 Apr 2011 13:59:18 +0000 (19:29 +0530)]
ath9k_hw: Assign macversion based on devid for built-in wmac
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Tue, 19 Apr 2011 13:59:17 +0000 (19:29 +0530)]
ath9k: Add AR9340 platform id to id table
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Tue, 19 Apr 2011 13:59:16 +0000 (19:29 +0530)]
ath9k_hw: Read iq calibration data only for active chains
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Tue, 19 Apr 2011 13:59:15 +0000 (19:29 +0530)]
ath9k_hw: Configure chain switch table and attenuation control only for active chains
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Tue, 19 Apr 2011 13:59:14 +0000 (19:29 +0530)]
ath9k_hw: Enable byte Tx/Rx data swap for AR9340
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Tue, 19 Apr 2011 13:59:13 +0000 (19:29 +0530)]
ath9k_hw: Configure tuning capacitance value for AR9340 as well
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Tue, 19 Apr 2011 13:59:12 +0000 (19:29 +0530)]
ath9k_hw: Skip internal regulator configuration for AR9340
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Tue, 19 Apr 2011 13:59:11 +0000 (19:29 +0530)]
ath9k_hw: Don't configure AR_CH0_THERM for AR9340
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Tue, 19 Apr 2011 13:59:10 +0000 (19:29 +0530)]
ath9k_hw: Fix register offset AR_PHY_65NM_CH0_THERM for AR9340
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Tue, 19 Apr 2011 13:59:09 +0000 (19:29 +0530)]
ath9k_hw: Clean up rx/tx chain configuration before AGC/IQ cal
Use hw supported chains instead of hard coded values.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Tue, 19 Apr 2011 13:59:08 +0000 (19:29 +0530)]
ath9k_hw: Configure RF channel freqency for AR9340
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Tue, 19 Apr 2011 13:59:07 +0000 (19:29 +0530)]
ath9k_hw: Read spur frequency information from eeprom for AR9340
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Tue, 19 Apr 2011 13:59:06 +0000 (19:29 +0530)]
ath9k_hw: Initialize tx and rx gain table from initvals.h for ar9340
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Tue, 19 Apr 2011 13:59:05 +0000 (19:29 +0530)]
ath9k_hw: Don't do ani initialization for AR9340
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Tue, 19 Apr 2011 13:59:04 +0000 (19:29 +0530)]
ath9k_hw: Initialize mode registers from initvals.h for AR9340
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Tue, 19 Apr 2011 13:59:03 +0000 (19:29 +0530)]
ath9k_hw: Add initvals.h for ar9340
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Wed, 20 Apr 2011 04:56:15 +0000 (10:26 +0530)]
ath9k_hw: Configure pll control register accordingly for AR9340
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Tue, 19 Apr 2011 13:59:01 +0000 (19:29 +0530)]
ath9k_hw: Get AHB clock information from ath9k_platform_data
Add a bool in ath9k_platform_data to pass AHB clock speed information.
Driver needs this to configure PLL on some SOCs.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Tue, 19 Apr 2011 13:59:00 +0000 (19:29 +0530)]
ath9k_hw: Take care of few host interface register changes for AR9340
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Tue, 19 Apr 2011 13:58:59 +0000 (19:28 +0530)]
ath9k_hw: Define devid and mac version for AR9340
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Mon, 25 Apr 2011 18:42:51 +0000 (14:42 -0400)]
Merge branch 'wireless-next-2.6' of git://git./linux/kernel/git/iwlwifi/iwlwifi-2.6
John W. Linville [Mon, 25 Apr 2011 18:36:35 +0000 (14:36 -0400)]
Merge branch 'for-linville' of git://git./linux/kernel/git/luca/wl12xx
Johannes Berg [Wed, 13 Apr 2011 10:14:52 +0000 (03:14 -0700)]
iwlagn: remove hw_ready variable
This variable is only ever checked right after
the function that sets it, but the same function
will also return the status, so we can pass it
through instead of checking hw_ready later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Sat, 16 Apr 2011 15:29:24 +0000 (08:29 -0700)]
iwlagn: combine firmware code/data
On new hardware, ucode images always come in
pairs: code and data. Therefore, combine the
variables into an appropriate struct and use
that when both code and data are needed.
Also, combine allocation and copying so that
we have less code in total.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Fri, 22 Apr 2011 17:15:23 +0000 (10:15 -0700)]
iwlagn: implement synchronous firmware load
The current firmware loading mechanism in
iwlwifi is very hard to follow, and thus
hard to maintain. To make it easier, make
the firmware loading synchronous.
For now, as a side effect, this removes a
number of retry possibilities we had. It
isn't typical for this to fail, but if it
does happen we restart from scratch which
this also makes easier to do should it be
necessary.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Wed, 13 Apr 2011 10:14:49 +0000 (03:14 -0700)]
iwlagn: leave notification waits on firmware errors
When the firmware encounters an error while the
driver is waiting for a notification, it will
never get that notification. Therefore, instead
of timing out, bail out on errors when waiting
for notifications.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Wed, 13 Apr 2011 10:14:48 +0000 (03:14 -0700)]
iwlagn: make iwlagn_wait_notification return error code
We're unlikely to care about the actual time spent
waiting, so make the function return an error code
which is less error prone in coding new uses.
Also, while at it, mark __must_check.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Wed, 13 Apr 2011 10:14:47 +0000 (03:14 -0700)]
iwlagn: extend notification wait function
A notification wait function is called with the
command, but currently has no way of passing
data back to the caller -- fix that by adding a
void pointer to the function that can be used
between the caller and the function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Wed, 13 Apr 2011 10:14:46 +0000 (03:14 -0700)]
iwlagn: refactor up path
Starting the device consists of many things,
refactor out enabling the hardware and also
return -ERFKILL when the rfkill signal is
found to be asserted (which makes more sense
anyway, but is also required now to make the
__iwl_up function return right away.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Wed, 13 Apr 2011 10:14:45 +0000 (03:14 -0700)]
iwlagn: refactor down path
The iwl_down path really consists of multiple things,
refactor out the hardware resetting (including, of
course, related software state like irqs).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Wed, 13 Apr 2011 10:14:44 +0000 (03:14 -0700)]
iwlagn: clean up some exit code
There's no point in running through iwl_down()
when we never registered with mac80211, as it
just cleans up internal structures that were
never initialised in this case. Therefore we
can also remove the special handling for this
case from __iwl_down().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Wed, 13 Apr 2011 10:14:43 +0000 (03:14 -0700)]
iwlagn: simplify error table reading
The current code to read the error table header
just hardcodes all the offsets, which is a bit
hard to understand. We can read in the entire
header (as much as we need) into a structure,
and then take the data from there, which makes
it easier to understand. To read a bigger blob
we also don't need to grab NIC access for each
word read, making the code more efficient.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Johannes Berg [Mon, 18 Apr 2011 15:05:21 +0000 (17:05 +0200)]
mac80211: explain padding in place of rate field
Apparently this was confusing still ... add a
note that the byte is needed as padding.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 18 Apr 2011 13:35:12 +0000 (15:35 +0200)]
rt2x00: Implement get_antenna and set_antenna callback functions
Implement the get_antenna and set_antenna callback functions, which will
allow clients to control the antenna for all non-11n hardware (Antenna handling
in rt2800 is still a bit magical, so we can't use the set_antenna for those drivers
yet).
To best support the set_antenna callback some modifications are needed in the
diversity handling. We should never look at the default antenna settings to determine
if software diversity is enabled. Instead we should set the diversity flag when
possible, which will allow the link_tuner to automatically pick up the tuning.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 18 Apr 2011 13:34:41 +0000 (15:34 +0200)]
rt2x00: Implement get_ringparam callback function
With the get_ringparam callback function we can export ring parameters
to ethtool through the mac80211 interface.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 18 Apr 2011 13:34:22 +0000 (15:34 +0200)]
rt2x00: Optimize register access in rt2800usb
All register reads/writes in rt2800usb were previously done with
rt2800_register_read/rt2800_register_write. These however indirectly
call rt2x00usb_register_read/rt2x00usb_register_write which adds an
additional overhead of at least one call and several move instructions
to each register access.
Replacing the calls to rt2800_register_read/rt2800_register_write with
direct calls to rt2x00usb_register_read/rt2x00usb_register_write gets
rid of quite a number of instructions in the drivers hotpaths (IRQ
handling and txdone handling).
For consistency replace all references to rt2800_register_read/write
with the rt2x00usb_register_read/write variants.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Mon, 18 Apr 2011 13:34:01 +0000 (15:34 +0200)]
rt2x00: Optimize register access in rt2800pci
All register reads/writes in rt2800pci were previously done with
rt2800_register_read/rt2800_register_write. These however indirectly
call rt2x00pci_register_read/rt2x00pci_register_write which adds an
additional overhead of at least one call and several move instructions
to each register access.
Replacing the calls to rt2800_register_read/rt2800_register_write with
direct calls to rt2x00pci_register_read/rt2x00pci_register_write gets
rid of quite a number of instructions in the drivers hotpaths (IRQ
handling and txdone handling).
For consistency replace all references to rt2800_register_read/write
with the rt2x00pci_register_read/write variants.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Mon, 18 Apr 2011 13:33:41 +0000 (15:33 +0200)]
rt2x00: Merge rt2x00ht.c contents in other files.
The two functions that are in rt2x00ht.c can be much better placed
closer to the places where the call-sites of these functions are (one
in rt2x00config.c and one in rt2x00queue.c) allowing us to make these
functions static.
Also, conditional compilations doesn't seem to be necessary anymore as
802.11n support is quite common nowadays.
This makes the code a bit easier readable and searchable.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Mon, 18 Apr 2011 13:33:20 +0000 (15:33 +0200)]
rt2x00: Enable support for RT53xx PCI devices by default.
Code seems to be feature-complete, so no reason to not enable
these devices by default.
Also, remove the sentence about the support for these devices being
non-functional.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Mon, 18 Apr 2011 13:33:00 +0000 (15:33 +0200)]
rt2x00: RT33xx device support is no longer experimental.
The rt33xx devices support for both PCI and USB devices has been in
the tree for a couple of months now, and seems to be functional and
not in a worse shape than the support for rt28xx and rt30xx devices.
No longer mark it as experimental and enable the support for these
devices by default.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Mon, 18 Apr 2011 13:32:33 +0000 (15:32 +0200)]
rt2x00: Add USB IDs.
Add USB IDs that are listed in the latest Ralink Windows and/or Linux drivers.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Mon, 18 Apr 2011 13:32:13 +0000 (15:32 +0200)]
rt2x00: Allow dynamic addition of PCI/USB IDs.
Both USB and PCI drivers allow a system administrator to dynamically add
USB/PCI IDs to the device table that a driver supports via the
/sys/bus/{usb,pci,pci_express}/drivers/<driver-name>/new_id files.
However, for the rt2x00 drivers using this method currently crashes the
system with a NULL pointer failure.
This is due to the set-up of rt2x00 where the probe functions require a
rt2x00_ops structure in the driver_info field of the probed device. As
this field is empty for the dynamically added devices this fails for
these devices.
Fix this by introducing driver-specific probe wrappers that do nothing
but calling the bus-specific probe functions with the rt2x00_ops structure
as an argument, rather than depending on the driver_info field.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Mon, 18 Apr 2011 13:31:50 +0000 (15:31 +0200)]
rt2x00: Linksys WUSB600N rev2 is a RT3572 device.
Move the USB ID entry from the unknown devices to the list of RT35xx based
devices.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Mon, 18 Apr 2011 13:31:31 +0000 (15:31 +0200)]
rt2x00: Always inline rt2x00pci_enable_interrupt
This allows the compiler to perform the necessary bitfield calculations
during compile time instead of run time and thus reduces the number of
instructions to run during each tasklet invocation. This should improve
performance in the RX hotpath.
This comes at the cost of a slight increase in the module size (for
example rt2800pci):
Before:
text data bss dec hex filename
14133 832 4 14969 3a79 drivers/net/wireless/rt2x00/rt2800pci.ko
After:
text data bss dec hex filename
14149 832 4 14985 3a89 drivers/net/wireless/rt2x00/rt2800pci.ko
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 18 Apr 2011 13:31:02 +0000 (15:31 +0200)]
rt2x00: Decrease association time for USB devices
When powersaving is enabled, assocaition times are very high
(for WPA2 networks, the time can easily be around the 3 seconds).
This is caused, because the flushing of the queues takes
too much time. Without the flushing callback mac80211 assumes
a timeout of 100ms while scanning. Limit all flush waiting
loops to the same maximum.
We can apply this maximum by passing the drop status to the
driver, which makes sure the driver performs extra actions
during the waiting for the queue to become empty.
After these changes, association times fall within the
healthy range of ~0.6 seconds with powersaving enabled.
The difference between association time between powersaving
enabled and disabled is now only ~0.1 second (which can also
be due to the measuring method).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Stezenbach [Mon, 18 Apr 2011 13:30:36 +0000 (15:30 +0200)]
rt2800usb: add timer to handle TX_STA_FIFO
TX status is reported by the hardware when a packet has been
sent (or after TX failed after possible retries), which is some
time after the DMA completion. Since the rt2800usb hardware can
not signal interrupts we have to use a timer, otherwise the
TX status would only be read by the next packet's TX DMA
completion, or by the watchdog thread.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Stezenbach [Mon, 18 Apr 2011 13:30:01 +0000 (15:30 +0200)]
rt2800usb: handle TX status timeouts
The watchdog just triggers rt2800usb_work_txdone() when it
detects a TX status timeout, thus rt2800usb_work_txdone() needs to
handle this case.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Stezenbach [Mon, 18 Apr 2011 13:29:38 +0000 (15:29 +0200)]
rt2x00: fix queue timeout checks
Add a timestamp to each queue entry which is updated whenever
the status of the entry changes, and remove the per-queue
timestamps. The previous check was incorrect and caused both
false positives and false negatives.
With the corrected check it comes apparent that the TX status
usually times out on rt2800usb unless there is sufficient traffic
(i.e. the next TX will complete the previous TX status).
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Stezenbach [Mon, 18 Apr 2011 13:29:12 +0000 (15:29 +0200)]
rt2800usb: read TX_STA_FIFO asynchronously
Trying to fix the "TX status report missed" warnings
by reading the TX_STA_FIFO entries as quickly as possible.
The TX_STA_FIFO is too small in hardware, thus reading
it only from the workqueue is too slow and entries get lost.
Start an asynchronous read of the TX_STA_FIFO directly from
the TX URB completion callback (atomic context, thus it cannot
use the blocking rt2800_register_read()). If the async
read returns a valid FIFO entry, it is pushed into a larger
FIFO inside struct rt2x00_dev, until rt2800_txdone() picks
it up.
A .tx_dma_done callback is added to struct rt2x00lib_ops
to trigger the async read from the URB completion callback.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Mon, 18 Apr 2011 13:28:50 +0000 (15:28 +0200)]
rt2x00: Use TXOP_HTTXOP for beacons
Use TXOP_HTTXOP for beacons to stay in sync with the legacy drivers.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Mon, 18 Apr 2011 13:28:27 +0000 (15:28 +0200)]
rt2x00: Update TX_SW_CFG2 init value
Bring the TX_SW_CFG2 initialisation for rt305x devices in sync with the
ralink legacy drivers.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Mon, 18 Apr 2011 13:28:04 +0000 (15:28 +0200)]
rt2x00: Use correct TBTT_SYNC config in AP mode
This seems to fix problems with some powersaving clients since a
positive value in TBTT_SYNC_CFG_TBTT_ADJUST introduces beacon skew,
which is not wanted in AP mode.
Also update the rest of the TBTT_SYNC config according to the
legacy drivers in AP mode.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Mon, 18 Apr 2011 13:27:43 +0000 (15:27 +0200)]
rt2x00: Make rt2x00_queue_entry_for_each more flexible
Allow passing a void pointer to rt2x00_queue_entry_for_each which in
turn in provided to the callback function.
Furthermore, allow the callback function to stop processing by returning
true. And also notify the caller of rt2x00_queue_entry_for_each if the
loop was canceled by the callback.
No functional changes, just preparation for an upcoming patch.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 18 Apr 2011 13:27:06 +0000 (15:27 +0200)]
rt2x00: Split rt2x00dev->flags
The number of flags defined for the rt2x00dev->flags field,
has been growing over the years. Currently we are approaching
the maximum number of bits which are available in the field.
A secondary problem, is that one part of the field are initialized only
during boot, because the driver requirements are initialized or device
requirements are loaded from the EEPROM. In both cases, the flags are
fixed and will not change during device operation. The other flags are
the device state, and will change frequently. So far this resulted in the fact
that for some flags, the atomic bit accessors are used, while for the others
the non-atomic variants are used.
By splitting the flags up into a "flags" and "cap_flags" we can put all flags
which are fixed inside "cap_flags". This field can then be read non-atomically.
In the "flags" field we keep the device state, which is going to be read atomically.
This adds more room for more flags in the future, and sanitizes the field access methods.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Mon, 18 Apr 2011 13:26:37 +0000 (15:26 +0200)]
rt2x00: Fix stuck queue in tx failure case
Since commit
0b7fde54f94979edc67bbf86b5adba702ebfefe8 "rt2x00: Protect
queue control with mutex" rt2x00 used rt2x00queue_pause_queue for
stopping a tx queue in mac80211. But in case of a failure in the tx
path rt2x00 still called ieee80211_stop_queue which stopped the queue
but prevented rt2x00queue_unpause_queue to wake the queue up again
resulting in a stuck tx queue.
Fix this by also using rt2x00queue_pause_queue in case of tx failures.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Layne Edwards [Mon, 18 Apr 2011 13:26:00 +0000 (15:26 +0200)]
rt2x00: Enable WLAN LED on Ralink SoC (rt305x) devices
This patch adds WLAN LED support to the mac80211 rt2x00 driver for
Ralink SoC (rt305x) devices. The current WLAN LED drivers in
rt2800lib.c set the LED brightness via an MCU request, but do nothing
for SoC. This patch checks for SoC and sets the register to enable the
WLAN LED (instead of an MCU request). This enables the WLAN LED for
RT305x devices.
Signed-off-by: Layne Edwards <ledwards@astrumtech.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 17 Apr 2011 21:28:10 +0000 (23:28 +0200)]
ath9k: assign keycache slots to unencrypted stations
Frame filtering relies on having a valid destination index (keycache slot),
to keep track of the destination. Assigning a keycache slot (configured
to unencrypted, with no key data attached) improves powersave handling in
AP mode with no encryption.
The dummy keycache entry for a station is cleared, when a real key gets
added.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 17 Apr 2011 21:28:09 +0000 (23:28 +0200)]
ath9k: fix powersave frame filtering/buffering in AP mode
This patch fixes a long standing issue of pending packets in the queue being
sent (and retransmitted many times) to sleeping stations.
This was made worse by aggregation through driver-internal retransmitting
of A-MDPU subframes.
Previously the hardware tx filter was cleared unconditionally for every
single packet - with this patch it uses the IEEE80211_TX_CTL_CLEAR_PS_FILT
for unaggregated frames.
A sta_notify driver op is added to stop aggregation for stations when they
enter powersave mode. Subframes stay buffered inside the driver, to ensure
that the BlockAck window keeps a sane state.
Since the driver uses software aggregation, the clearing of the tx filter
needs to be handled by the driver instead of mac80211 for aggregated frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Sun, 17 Apr 2011 16:08:10 +0000 (21:38 +0530)]
ath9k: Fix beacon generation on foreign channel
While leaving the oper channel, beacon generation is stopped
by mac80211 and beacon slots are marked as inactive.
During the scan, ath9k configures beacon timers
based on IEEE80211_CONF_OFFCHANNEL which inturn generates
beacon alert even though bslot is inactive.
ath9k fails to disable beacon alert while moving to offchannel
if none of the beacon slot is active. This is causing beacon
transmission on foreign channel. This patch enables swba
based on active bslots.
This issue was reported with two vifs (AP+STA) and triggered
scan in STA vif in unassociated state.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 17 Apr 2011 15:45:00 +0000 (17:45 +0200)]
mac80211: add a function for setting the TIM bit for a specific station
This allows a driver to buffer frames for a PS station and tell mac80211
to wake it up even though mac80211 does not have any buffered frames for
it.
This is necessary for properly handling aggregation related buffering,
in ath9k, because the driver needs to keep its frames in order to keep
track of the Block-ACK window.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Sat, 16 Apr 2011 08:47:39 +0000 (14:17 +0530)]
ath9k_htc: Fix free slot value for cab queue
ath9k_htc_tx_get_slot can return zero as valid index.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Acked-by: Sujith Manoharan <Sujith.Manoharan@Atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Sat, 16 Apr 2011 03:50:42 +0000 (20:50 -0700)]
mwifiex: optimize driver initialization code
1) removal of unnecessary mwifiex_device structure
2) avoid passing adapter pointer to mwifiex_init_sw()
3) remove local variable drv_mode_info in mwifiex_add_card()
4) type change in mwifiex_bss_attr to match mwifiex_private
5) removal of more wordy comments
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Sat, 16 Apr 2011 03:50:41 +0000 (20:50 -0700)]
mwifiex: remove some macro definitions
use corresponding macros defined in include/linux/ieee80211.h
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yogesh Ashok Powar [Sat, 16 Apr 2011 03:50:40 +0000 (20:50 -0700)]
mwifiex: remove redundant local variables and comments
Remove some local variables (mainly function return values)
that are used only once. Also, one dummy function and some
wordy comments are removed.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Randy Dunlap [Fri, 15 Apr 2011 23:20:05 +0000 (16:20 -0700)]
mac80211: fix debugfs printk format warning
Fix printf() format warning (tm_year is long int):
net/mac80211/debugfs_sta.c:113: warning: format '%d' expects type 'int', but argument 4 has type 'long int'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sergei Shtylyov [Fri, 15 Apr 2011 15:23:11 +0000 (19:23 +0400)]
iwlegacy: use pci_dev->revision
Commit
be663ab67077fac8e23eb8e231a8c1c94cb32e54 (iwlwifi: split the drivers for
agn and legacy devices 3945/4965) added code to read the 4965's revision ID from
the PCI configuration register while it's already stored by PCI subsystem in the
'revision' field of 'struct pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Fri, 15 Apr 2011 10:12:24 +0000 (15:42 +0530)]
ath9k_htc: Cleanup HTC debugfs
Move the ath9k_htc debugfs under ieee80211 to be inline
with ath9k driver and it also helps to simplify debug code.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Acked-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Fri, 15 Apr 2011 06:58:52 +0000 (12:28 +0530)]
ath9k_htc: Add debugfs support to change debug mask
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Acked-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Thu, 14 Apr 2011 21:55:36 +0000 (14:55 -0700)]
ath: fix 0x6C for beaconing/passive scan flags based on country IE
The 0x6C regulatory domain is just like the 0x6A regulatory
domain but differs in that 0x6C will allow adhoc and active
scan on its channels only if we are associated to an AP
with a country IE that allows those channels. The
ath_reg_apply_beaconing_flags() does just this -- we respect
the manufacturer's intent on only enabling beaconing modes
of operation if and only if blessed by the country IE.
Cc: David Quan <david.quan@atheros.com>
Cc: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Antonio Ospite [Wed, 13 Apr 2011 19:40:45 +0000 (21:40 +0200)]
rfkill: Regulator consumer driver for rfkill
Add a regulator consumer driver for rfkill to enable controlling radio
transmitters connected to voltage regulators using the regulator
framework.
A new "vrfkill" virtual supply is provided to use in platform code.
Signed-off-by: Guiming Zhuo <gmzhuo@gmail.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Tue, 19 Apr 2011 19:34:48 +0000 (15:34 -0400)]
Merge branch 'master' of git://git./linux/kernel/git/padovan/bluetooth-next-2.6
John W. Linville [Tue, 19 Apr 2011 19:33:54 +0000 (15:33 -0400)]
Merge branch 'wireless-next-2.6' of git://git./linux/kernel/git/iwlwifi/iwlwifi-2.6
Luciano Coelho [Fri, 1 Apr 2011 18:08:23 +0000 (21:08 +0300)]
wl12xx: fix sparse warning about undeclared wl12xx_alloc_dummy_packet
Fix sparse warning:
CHECK drivers/net/wireless/wl12xx/main.c
drivers/net/wireless/wl12xx/main.c:1246:17: warning: symbol 'wl12xx_alloc_dummy_packet' was not declared. Should it be static?
Signed-off-by: Luciano Coelho <coelho@ti.com>
Luciano Coelho [Fri, 1 Apr 2011 17:55:01 +0000 (20:55 +0300)]
wl12xx: remove unused conf_radio_params structure
This structure has not been used anymore since commit
e6b190ff3c2f4e4859502c41fa17b5c595e82000.
Signed-off-by: Luciano Coelho <coelho@ti.com>
projects / openwrt / staging / blogic.git / log