David S. Miller [Sat, 30 Jun 2018 09:51:06 +0000 (18:51 +0900)]
Merge branch 'DPAA-fixes'
Madalin Bucur says:
====================
DPAA fixes
A couple of fixes for the DPAA drivers, addressing an issue
with short UDP or TCP frames (with padding) that were marked
as having a wrong checksum and dropped by the FMan hardware
and a problem with the buffer used for the scatter-gather
table being too small as per the hardware requirements.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin Bucur [Thu, 28 Jun 2018 12:26:51 +0000 (15:26 +0300)]
dpaa_eth: DPAA SGT needs to be 256B
The DPAA HW requires that at least 256 bytes from the start of the
first scatter-gather table entry are allocated and accessible. The
hardware reads the maximum size the table can have in one access,
thus requiring that the allocation and mapping to be done for the
maximum size of 256B even if there is a smaller number of entries
in the table.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin Bucur [Thu, 28 Jun 2018 12:26:50 +0000 (15:26 +0300)]
fsl/fman: fix parser reporting bad checksum on short frames
The FMan hardware parser needs to be configured to remove the
short frame padding from the checksum calculation, otherwise
short UDP and TCP frames are likely to be marked as having a
bad checksum.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Reddy Kalluru [Thu, 28 Jun 2018 11:52:15 +0000 (04:52 -0700)]
bnx2x: Fix receiving tx-timeout in error or recovery state.
Driver performs the internal reload when it receives tx-timeout event from
the OS. Internal reload might fail in some scenarios e.g., fatal HW issues.
In such cases OS still see the link, which would result in undesirable
functionalities such as re-generation of tx-timeouts.
The patch addresses this issue by indicating the link-down to OS when
tx-timeout is detected, and keeping the link in down state till the
internal reload is successful.
Please consider applying it to 'net' branch.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Thu, 28 Jun 2018 09:31:25 +0000 (12:31 +0300)]
cnic: tidy up a size calculation
Static checkers complain that id_tbl->table points to longs and 4 bytes
is smaller than sizeof(long). But the since other side is dividing by
32 instead of sizeof(long), that means the current code works fine.
Anyway, it's more conventional to use the BITS_TO_LONGS() macro when
we're allocating a bitmap.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Thu, 28 Jun 2018 09:24:42 +0000 (12:24 +0300)]
atm: iphase: fix a 64 bit bug
The code assumes that there is 4 bytes in a pointer and it doesn't
allocate enough memory.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng [Wed, 27 Jun 2018 23:04:48 +0000 (16:04 -0700)]
tcp: fix Fast Open key endianness
Fast Open key could be stored in different endian based on the CPU.
Previously hosts in different endianness in a server farm using
the same key config (sysctl value) would produce different cookies.
This patch fixes it by always storing it as little endian to keep
same API for LE hosts.
Reported-by: Daniele Iamartino <danielei@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 29 Jun 2018 13:09:26 +0000 (22:09 +0900)]
Merge tag 'mac80211-for-davem-2018-06-29' of git://git./linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just three fixes:
* fix HT operation in mesh mode
* disable preemption in control frame TX
* check nla_parse_nested() return values
where missing (two places)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Shakeel Butt [Wed, 27 Jun 2018 22:16:42 +0000 (15:16 -0700)]
net, mm: account sock objects to kmemcg
Currently the kernel accounts the memory for network traffic through
mem_cgroup_[un]charge_skmem() interface. However the memory accounted
only includes the truesize of sk_buff which does not include the size of
sock objects. In our production environment, with opt-out kmem
accounting, the sock kmem caches (TCP[v6], UDP[v6], RAW[v6], UNIX) are
among the top most charged kmem caches and consume a significant amount
of memory which can not be left as system overhead. So, this patch
converts the kmem caches of all sock objects to SLAB_ACCOUNT.
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Fri, 29 Jun 2018 07:33:39 +0000 (09:33 +0200)]
nl80211: check nla_parse_nested() return values
At the very least we should check the return value if
nla_parse_nested() is called with a non-NULL policy.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Bob Copeland [Mon, 25 Jun 2018 01:10:49 +0000 (21:10 -0400)]
nl80211: relax ht operation checks for mesh
Commit
9757235f451c, "nl80211: correct checks for
NL80211_MESHCONF_HT_OPMODE value") relaxed the range for the HT
operation field in meshconf, while also adding checks requiring
the non-greenfield and non-ht-sta bits to be set in certain
circumstances. The latter bit is actually reserved for mesh BSSes
according to Table 9-168 in 802.11-2016, so in fact it should not
be set.
wpa_supplicant sets these bits because the mesh and AP code share
the same implementation, but authsae does not. As a result, some
meshconf updates from authsae which set only the NONHT_MIXED
protection bits were being rejected.
In order to avoid breaking userspace by changing the rules again,
simply accept the values with or without the bits set, and mask
off the reserved bit to match the spec.
While in here, update the 802.11-2012 reference to 802.11-2016.
Fixes: 9757235f451c ("nl80211: correct checks for NL80211_MESHCONF_HT_OPMODE value")
Cc: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Reviewed-by: Masashi Honma <masashi.honma@gmail.com>
Reviewed-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Denis Kenzior [Tue, 19 Jun 2018 15:39:50 +0000 (10:39 -0500)]
mac80211: disable BHs/preemption in ieee80211_tx_control_port()
On pre-emption enabled kernels the following print was being seen due to
missing local_bh_disable/local_bh_enable calls. mac80211 assumes that
pre-emption is disabled in the data path.
BUG: using smp_processor_id() in preemptible [
00000000] code: iwd/517
caller is __ieee80211_subif_start_xmit+0x144/0x210 [mac80211]
[...]
Call Trace:
dump_stack+0x5c/0x80
check_preemption_disabled.cold.0+0x46/0x51
__ieee80211_subif_start_xmit+0x144/0x210 [mac80211]
Fixes: 911806491425 ("mac80211: Add support for tx_control_port")
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
[commit message rewrite, fixes tag]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jose Abreu [Wed, 27 Jun 2018 14:03:20 +0000 (15:03 +0100)]
net: stmmac: Set DMA buffer size in HW
This is clearly a bug.
We need to set the DMA buffer size in the HW otherwise corruption can
occur when receiving packets.
This is probably not occuring because of small MTU values and because HW
has a default value internally (which currently is bigger than default
buffer size).
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Wed, 27 Jun 2018 15:59:50 +0000 (17:59 +0200)]
net/smc: rebuild nonblocking connect
The recent poll change may lead to stalls for non-blocking connecting
SMC sockets, since sock_poll_wait is no longer performed on the
internal CLC socket, but on the outer SMC socket. kernel_connect() on
the internal CLC socket returns with -EINPROGRESS, but the wake up
logic does not work in all cases. If the internal CLC socket is still
in state TCP_SYN_SENT when polled, sock_poll_wait() from sock_poll()
does not sleep. It is supposed to sleep till the state of the internal
CLC socket switches to TCP_ESTABLISHED.
This problem triggered a redesign of the SMC nonblocking connect logic.
This patch introduces a connect worker covering all connect steps
followed by a wake up of socket waiters. It allows to get rid of all
delays and locks in smc_poll().
Fixes: c0129a061442 ("smc: convert to ->poll_mask")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 27 Jun 2018 15:47:21 +0000 (08:47 -0700)]
tcp: add one more quick ack after after ECN events
Larry Brakmo proposal ( https://patchwork.ozlabs.org/patch/935233/
tcp: force cwnd at least 2 in tcp_cwnd_reduction) made us rethink
about our recent patch removing ~16 quick acks after ECN events.
tcp_enter_quickack_mode(sk, 1) makes sure one immediate ack is sent,
but in the case the sender cwnd was lowered to 1, we do not want
to have a delayed ack for the next packet we will receive.
Fixes: 522040ea5fdd ("tcp: do not aggressively quick ack after ECN events")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Neal Cardwell <ncardwell@google.com>
Cc: Lawrence Brakmo <brakmo@fb.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Masahiro Yamada [Wed, 27 Jun 2018 03:13:48 +0000 (20:13 -0700)]
bpfilter: include bpfilter_umh in assembly instead of using objcopy
What we want here is to embed a user-space program into the kernel.
Instead of the complex ELF magic, let's simply wrap it in the assembly
with the '.incbin' directive.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Doron Roberts-Kedes [Wed, 27 Jun 2018 01:33:33 +0000 (18:33 -0700)]
strparser: Remove early eaten to fix full tcp receive buffer stall
On receving an incomplete message, the existing code stores the
remaining length of the cloned skb in the early_eaten field instead of
incrementing the value returned by __strp_recv. This defers invocation
of sock_rfree for the current skb until the next invocation of
__strp_recv, which returns early_eaten if early_eaten is non-zero.
This behavior causes a stall when the current message occupies the very
tail end of a massive skb, and strp_peek/need_bytes indicates that the
remainder of the current message has yet to arrive on the socket. The
TCP receive buffer is totally full, causing the TCP window to go to
zero, so the remainder of the message will never arrive.
Incrementing the value returned by __strp_recv by the amount otherwise
stored in early_eaten prevents stalls of this nature.
Signed-off-by: Doron Roberts-Kedes <doronrk@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 28 Jun 2018 07:21:35 +0000 (16:21 +0900)]
Merge tag 'mlx5-fixes-2018-06-26' of git://git./linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-fixes-2018-06-26
Fixes for mlx5 core and netdev driver:
Two fixes from Alex Vesker to address command interface issues
- Race in command interface polling mode
- Incorrect raw command length parsing
From Shay Agroskin, Fix wrong size allocation for QoS ETC TC regitster.
From Or Gerlitz and Eli Cohin, Address backward compatability issues for when
Eswitch capability is not advertised for the PF host driver
- Fix required capability for manipulating MPFS
- E-Switch, Disallow vlan/spoofcheck setup if not being esw manager
- Avoid dealing with vport IB/eth representors if not being e-switch manager
- E-Switch, Avoid setup attempt if not being e-switch manager
- Don't attempt to dereference the ppriv struct if not being eswitch manager
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Shuah Khan [Tue, 26 Jun 2018 18:22:28 +0000 (12:22 -0600)]
selftests/net: Fix permissions for fib_tests.sh
fib_tests.sh became non-executable at some point. This is
what happens:
selftests: net: fib_tests.sh: Warning: file fib_tests.sh is
not executable, correct this.
not ok 1..11 selftests: net: fib_tests.sh [FAIL]
Fixes: d69faad76584 ("selftests: fib_tests: Add prefix route tests with metric")
Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 28 Jun 2018 05:27:52 +0000 (14:27 +0900)]
Merge branch 'xdp-flush'
Jesper Dangaard Brouer says:
====================
xdp: don't mix XDP_TX and XDP_REDIRECT flush ops
Fix driver logic that are combining XDP_TX flush and XDP_REDIRECT map
flushing. These are two different XDP xmit modes, and it is clearly
wrong to invoke both types of flush operations when only one of the
XDP xmit modes is used.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Dangaard Brouer [Tue, 26 Jun 2018 15:39:58 +0000 (17:39 +0200)]
virtio_net: split XDP_TX kick and XDP_REDIRECT map flushing
The driver was combining XDP_TX virtqueue_kick and XDP_REDIRECT
map flushing (xdp_do_flush_map). This is suboptimal, these two
flush operations should be kept separate.
The suboptimal behavior was introduced in commit
9267c430c6b6
("virtio-net: add missing virtqueue kick when flushing packets").
Fixes: 9267c430c6b6 ("virtio-net: add missing virtqueue kick when flushing packets")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Dangaard Brouer [Tue, 26 Jun 2018 15:39:53 +0000 (17:39 +0200)]
i40e: split XDP_TX tail and XDP_REDIRECT map flushing
The driver was combining the XDP_TX tail flush and XDP_REDIRECT
map flushing (xdp_do_flush_map). This is suboptimal, these two
flush operations should be kept separate.
It looks like the mistake was copy-pasted from ixgbe.
Fixes: d9314c474d4f ("i40e: add support for XDP_REDIRECT")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Dangaard Brouer [Tue, 26 Jun 2018 15:39:48 +0000 (17:39 +0200)]
ixgbe: split XDP_TX tail and XDP_REDIRECT map flushing
The driver was combining the XDP_TX tail flush and XDP_REDIRECT
map flushing (xdp_do_flush_map). This is suboptimal, these two
flush operations should be kept separate.
Fixes: 11393cc9b9be ("xdp: Add batching support to redirect map")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandre Belloni [Tue, 26 Jun 2018 08:44:01 +0000 (10:44 +0200)]
net: macb: initialize bp->queues[0].bp for at91rm9200
The macb driver currently crashes on at91rm9200 with the following trace:
Unable to handle kernel NULL pointer dereference at virtual address
00000014
[...]
[<
c031da44>] (macb_rx_desc) from [<
c031f2bc>] (at91ether_open+0x2e8/0x3f8)
[<
c031f2bc>] (at91ether_open) from [<
c041e8d8>] (__dev_open+0x120/0x13c)
[<
c041e8d8>] (__dev_open) from [<
c041ec08>] (__dev_change_flags+0x17c/0x1a8)
[<
c041ec08>] (__dev_change_flags) from [<
c041ec4c>] (dev_change_flags+0x18/0x4c)
[<
c041ec4c>] (dev_change_flags) from [<
c07a5f4c>] (ip_auto_config+0x220/0x10b0)
[<
c07a5f4c>] (ip_auto_config) from [<
c000a4fc>] (do_one_initcall+0x78/0x18c)
[<
c000a4fc>] (do_one_initcall) from [<
c0783e50>] (kernel_init_freeable+0x184/0x1c4)
[<
c0783e50>] (kernel_init_freeable) from [<
c0574d70>] (kernel_init+0x8/0xe8)
[<
c0574d70>] (kernel_init) from [<
c00090e0>] (ret_from_fork+0x14/0x34)
Solve that by initializing bp->queues[0].bp in at91ether_init (as is done
in macb_init).
Fixes: ae1f2a56d273 ("net: macb: Added support for many RX queues")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Masahiro Yamada [Tue, 26 Jun 2018 03:55:35 +0000 (12:55 +0900)]
bpfilter: check compiler capability in Kconfig
With the brand-new syntax extension of Kconfig, we can directly
check the compiler capability in the configuration phase.
If the cc-can-link.sh fails, the BPFILTER_UMH is automatically
hidden by the dependency.
I also deleted 'default n', which is no-op.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Wed, 27 Jun 2018 09:47:37 +0000 (17:47 +0800)]
hinic: reset irq affinity before freeing irq
Following warning is seen when rmmod hinic. This is because affinity
value is not reset before calling free_irq(). This patch fixes it.
[ 55.181232] WARNING: CPU: 38 PID: 19589 at kernel/irq/manage.c:1608
__free_irq+0x2aa/0x2c0
Fixes: 352f58b0d9f2 ("net-next/hinic: Set Rxq irq to specific cpu for NUMA")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 28 Jun 2018 04:32:44 +0000 (13:32 +0900)]
Merge git://git./pub/scm/linux/kernel/git/pablo/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree:
1) Missing netlink attribute validation in nf_queue, uncovered by KASAN,
from Eric Dumazet.
2) Use pointer to sysctl table, save us 192 bytes of memory per netns.
Also from Eric.
3) Possible use-after-free when removing conntrack helper modules due
to missing synchronize RCU call. From Taehee Yoo.
4) Fix corner case in systcl writes to nf_log that lead to appending
data to uninitialized buffer, from Jann Horn.
5) Jann Horn says we may indefinitely block other users of nf_log_mutex
if a userspace access in proc_dostring() blocked e.g. due to a
userfaultfd.
6) Fix garbage collection race for unconfirmed conntrack entries,
from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Chengguang Xu [Tue, 26 Jun 2018 01:16:31 +0000 (09:16 +0800)]
nfp: cast sizeof() to int when comparing with error code
sizeof() will return unsigned value so in the error check
negative error code will be always larger than sizeof().
Fixes: a0d8e02c35ff ("nfp: add support for reading nffw info")
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 27 Jun 2018 01:46:43 +0000 (10:46 +0900)]
Merge branch 'nfp-MPLS-and-shared-blocks-TC-offload-fixes'
Jakub Kicinski says:
====================
nfp: MPLS and shared blocks TC offload fixes
This series brings two fixes to TC filter/action offload code.
Pieter fixes matching MPLS packets when the match is purely on
the MPLS ethertype and none of the MPLS fields are used.
John provides a fix for offload of shared blocks. Unfortunately,
with shared blocks there is currently no guarantee that filters
which were added by the core will be removed before block unbind.
Our simple fix is to not support offload of rules on shared blocks
at all, a revert of this fix will be send for -next once the
reoffload infrastructure lands. The shared blocks became important
as we are trying to use them for bonding offload (managed from user
space) and lack of remove calls leads to resource leaks.
v2:
- fix build error reported by kbuild bot due to missing
tcf_block_shared() helper.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
John Hurley [Tue, 26 Jun 2018 03:36:28 +0000 (20:36 -0700)]
nfp: reject binding to shared blocks
TC shared blocks allow multiple qdiscs to be grouped together and filters
shared between them. Currently the chains of filters attached to a block
are only flushed when the block is removed. If a qdisc is removed from a
block but the block still exists, flow del messages are not passed to the
callback registered for that qdisc. For the NFP, this presents the
possibility of rules still existing in hw when they should be removed.
Prevent binding to shared blocks until the kernel can send per qdisc del
messages when block unbinds occur.
tcf_block_shared() was not used outside of the core until now, so also
add an empty implementation for builds with CONFIG_NET_CLS=n.
Fixes: 4861738775d7 ("net: sched: introduce shared filter blocks infrastructure")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pieter Jansen van Vuuren [Tue, 26 Jun 2018 03:36:27 +0000 (20:36 -0700)]
nfp: flower: fix mpls ether type detection
Previously it was not possible to distinguish between mpls ether types and
other ether types. This leads to incorrect classification of offloaded
filters that match on mpls ether type. For example the following two
filters overlap:
# tc filter add dev eth0 parent ffff: \
protocol 0x8847 flower \
action mirred egress redirect dev eth1
# tc filter add dev eth0 parent ffff: \
protocol 0x0800 flower \
action mirred egress redirect dev eth2
The driver now correctly includes the mac_mpls layer where HW stores mpls
fields, when it detects an mpls ether type. It also sets the MPLS_Q bit to
indicate that the filter should match mpls packets.
Fixes: bb055c198d9b ("nfp: add mpls match offloading support")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason A. Donenfeld [Mon, 25 Jun 2018 23:39:32 +0000 (01:39 +0200)]
fib_rules: match rules based on suppress_* properties too
Two rules with different values of suppress_prefix or suppress_ifgroup
are not the same. This fixes an -EEXIST when running:
$ ip -4 rule add table main suppress_prefixlength 0
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Fixes: f9d4b0c1e969 ("fib_rules: move common handling of newrule delrule msgs into fib_nl2rule")
Signed-off-by: David S. Miller <davem@davemloft.net>
Sowmini Varadhan [Mon, 25 Jun 2018 13:41:25 +0000 (06:41 -0700)]
rds: clean up loopback rds_connections on netns deletion
The RDS core module creates rds_connections based on callbacks
from rds_loop_transport when sending/receiving packets to local
addresses.
These connections will need to be cleaned up when they are
created from a netns that is not init_net, and that netns is deleted.
Add the changes aligned with the changes from
commit
ebeeb1ad9b8a ("rds: tcp: use rds_destroy_pending() to synchronize
netns/module teardown and rds connection/workq management") for
rds_loop_transport
Reported-and-tested-by: syzbot+4c20b3866171ce8441d2@syzkaller.appspotmail.com
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Vesker [Tue, 12 Jun 2018 13:14:31 +0000 (16:14 +0300)]
net/mlx5: Fix command interface race in polling mode
The command interface can work in two modes: Events and Polling.
In the general case, each time we invoke a command, a work is
queued to handle it.
When working in events, the interrupt handler completes the
command execution. On the other hand, when working in polling
mode, the work itself completes it.
Due to a bug in the work handler, a command could have been
completed by the interrupt handler, while the work handler
hasn't finished yet, causing the it to complete once again
if the command interface mode was changed from Events to
polling after the interrupt handler was called.
mlx5_unload_one()
mlx5_stop_eqs()
// Destroy the EQ before cmd EQ
...cmd_work_handler()
write_doorbell()
--> EVENT_TYPE_CMD
mlx5_cmd_comp_handler() // First free
free_ent(cmd, ent->idx)
complete(&ent->done)
<-- mlx5_stop_eqs //cmd was complete
// move to polling before destroying the last cmd EQ
mlx5_cmd_use_polling()
cmd->mode = POLL;
--> cmd_work_handler (continues)
if (cmd->mode == POLL)
mlx5_cmd_comp_handler() // Double free
The solution is to store the cmd->mode before writing the doorbell.
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Alex Vesker [Fri, 25 May 2018 17:25:59 +0000 (20:25 +0300)]
net/mlx5: Fix incorrect raw command length parsing
The NULL character was not set correctly for the string containing
the command length, this caused failures reading the output of the
command due to a random length. The fix is to initialize the output
length string.
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Shay Agroskin [Tue, 22 May 2018 11:14:02 +0000 (14:14 +0300)]
net/mlx5: Fix wrong size allocation for QoS ETC TC regitster
The driver allocates wrong size (due to wrong struct name) when issuing
a query/set request to NIC's register.
Fixes: d8880795dabf ("net/mlx5e: Implement DCBNL IEEE max rate")
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eli Cohen [Wed, 13 Jun 2018 07:27:34 +0000 (10:27 +0300)]
net/mlx5: Fix required capability for manipulating MPFS
Manipulating of the MPFS requires eswitch manager capabilities.
Fixes: eeb66cdb6826 ('net/mlx5: Separate between E-Switch and MPFS')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eli Cohen [Thu, 31 May 2018 09:24:48 +0000 (12:24 +0300)]
net/mlx5: E-Switch, Disallow vlan/spoofcheck setup if not being esw manager
In smartnic env, if the host (PF) driver is not an e-switch manager, we
are not allowed to apply eswitch ports setups such as vlan (VST),
spoof-checks, min/max rate or state.
Make sure we are eswitch manager when coming to issue these callbacks
and err otherwise.
Also fix the definition of ESW_ALLOWED to rely on eswitch_manager
capability and on the vport_group_manger.
Operations on the VF nic vport context, such as setting a mac or reading
the vport counters are allowed to the PF in this scheme.
The modify nic vport guid code was modified to omit checking the
nic_vport_node_guid_modify eswitch capability.
The reason for doing so is that modifying node guid requires vport group
manager capability, and there's no need to check further capabilities.
1. set_vf_vlan - disallowed
2. set_vf_spoofchk - disallowed
3. set_vf_mac - allowed
4. get_vf_config - allowed
5. set_vf_trust - disallowed
6. set_vf_rate - disallowed
7. get_vf_stat - allowed
8. set_vf_link_state - disallowed
Fixes: f942380c1239 ('net/mlx5: E-Switch, Vport ingress/egress ACLs rules for spoofchk')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Tested-by: Or Gerlitz <ogerlitz@mellanox.com>
Or Gerlitz [Thu, 31 May 2018 08:40:17 +0000 (11:40 +0300)]
IB/mlx5: Avoid dealing with vport representors if not being e-switch manager
In smartnic env, the host (PF) driver might not be an e-switch
manager, hence the switchdev mode representors are running on
the embedded cpu (EC) and not at the host.
As such, we should avoid dealing with vport representors if
not being esw manager.
Fixes: b5ca15ad7e61 ('IB/mlx5: Add proper representors support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Or Gerlitz [Thu, 31 May 2018 08:32:56 +0000 (11:32 +0300)]
net/mlx5e: Avoid dealing with vport representors if not being e-switch manager
In smartnic env, the host (PF) driver might not be an e-switch
manager, hence the switchdev mode representors are running on
the embedded cpu (EC) and not at the host.
As such, we should avoid dealing with vport representors if
not being esw manager.
While here, make sure to disallow eswitch switchdev related
setups through devlink if we are not esw managers.
Fixes: cb67b832921c ('net/mlx5e: Introduce SRIOV VF representors')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Or Gerlitz [Thu, 31 May 2018 08:16:18 +0000 (11:16 +0300)]
net/mlx5: E-Switch, Avoid setup attempt if not being e-switch manager
In smartnic env, the host (PF) driver might not be an e-switch
manager, hence the FW will err on driver attempts to deal with
setting/unsetting the eswitch and as a result the overall setup
of sriov will fail.
Fix that by avoiding the operation if e-switch management is not
allowed for this driver instance. While here, move to use the
correct name for the esw manager capability name.
Fixes: 81848731ff40 ('net/mlx5: E-Switch, Add SR-IOV (FDB) support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Guy Kushnir <guyk@mellanox.com>
Reviewed-by: Eli Cohen <eli@melloanox.com>
Tested-by: Eli Cohen <eli@melloanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Or Gerlitz [Mon, 4 Jun 2018 16:46:53 +0000 (19:46 +0300)]
net/mlx5e: Don't attempt to dereference the ppriv struct if not being eswitch manager
The check for cpu hit statistics was not returning immediate false for
any non vport rep netdev and hence we crashed (say on mlx5 probed VFs) if
user-space tool was calling into any possible netdev in the system.
Fix that by doing a proper check before dereferencing.
Fixes: 1d447a39142e ('net/mlx5e: Extendable vport representor netdev private data')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Eli Cohen <eli@melloanox.com>
Reviewed-by: Eli Cohen <eli@melloanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Florian Westphal [Wed, 20 Jun 2018 21:32:26 +0000 (23:32 +0200)]
netfilter: nf_conncount: fix garbage collection confirm race
Yi-Hung Wei and Justin Pettit found a race in the garbage collection scheme
used by nf_conncount.
When doing list walk, we lookup the tuple in the conntrack table.
If the lookup fails we remove this tuple from our list because
the conntrack entry is gone.
This is the common cause, but turns out its not the only one.
The list entry could have been created just before by another cpu, i.e. the
conntrack entry might not yet have been inserted into the global hash.
The avoid this, we introduce a timestamp and the owning cpu.
If the entry appears to be stale, evict only if:
1. The current cpu is the one that added the entry, or,
2. The timestamp is older than two jiffies
The second constraint allows GC to be taken over by other
cpu too (e.g. because a cpu was offlined or napi got moved to another
cpu).
We can't pretend the 'doubtful' entry wasn't in our list.
Instead, when we don't find an entry indicate via IS_ERR
that entry was removed ('did not exist' or withheld
('might-be-unconfirmed').
This most likely also fixes a xt_connlimit imbalance earlier reported by
Dmitry Andrianov.
Cc: Dmitry Andrianov <dmitry.andrianov@alertme.com>
Reported-by: Justin Pettit <jpettit@vmware.com>
Reported-by: Yi-Hung Wei <yihung.wei@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Yi-Hung Wei <yihung.wei@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Jann Horn [Mon, 25 Jun 2018 15:22:00 +0000 (17:22 +0200)]
netfilter: nf_log: don't hold nf_log_mutex during user access
The old code would indefinitely block other users of nf_log_mutex if
a userspace access in proc_dostring() blocked e.g. due to a userfaultfd
region. Fix it by moving proc_dostring() out of the locked region.
This is a followup to commit
266d07cb1c9a ("netfilter: nf_log: fix
sleeping function called from invalid context"), which changed this code
from using rcu_read_lock() to taking nf_log_mutex.
Fixes: 266d07cb1c9a ("netfilter: nf_log: fix sleeping function calle[...]")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Jann Horn [Wed, 20 Jun 2018 16:33:45 +0000 (18:33 +0200)]
netfilter: nf_log: fix uninit read in nf_log_proc_dostring
When proc_dostring() is called with a non-zero offset in strict mode, it
doesn't just write to the ->data buffer, it also reads. Make sure it
doesn't read uninitialized data.
Fixes: c6ac37d8d884 ("netfilter: nf_log: fix error on write NONE to [...]")
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
David S. Miller [Tue, 26 Jun 2018 13:53:29 +0000 (22:53 +0900)]
Merge branch 'lan78xx-minor-fixes'
Dave Stevenson says:
====================
lan78xx minor fixes
This is a small set of patches for the Microchip LAN78xx chip,
as used in the Raspberry Pi 3B+.
The main debug/discussion was on
https://github.com/raspberrypi/linux/issues/2458
Initial symptoms were that VLANs were very unreliable.
A couple of things were found:
- firstly that the hardware timeout value set failed to
take into account the VLAN tag, so a full MTU packet
would be timed out.
- second was that regular checksum failures were being
reported. Disabling checksum offload confirmed that
the checksums were valid, and further experimentation
identified that it was only if the VLAN tags were being
passed through to the kernel that there were issues.
The hardware supports VLAN filtering and tag stripping,
therefore those have been implemented (much of the work
was already done), and the driver drops back to s/w
checksums should the choice be made not to use the h/w
VLAN stripping.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Stevenson [Mon, 25 Jun 2018 14:07:15 +0000 (15:07 +0100)]
net: lan78xx: Use s/w csum check on VLANs without tag stripping
Observations of VLANs dropping packets due to invalid
checksums when not offloading VLAN tag receive.
With VLAN tag stripping enabled no issue is observed.
Drop back to s/w checksums if VLAN offload is disabled.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Stevenson [Mon, 25 Jun 2018 14:07:14 +0000 (15:07 +0100)]
net: lan78xx: Add support for VLAN tag stripping.
The chip supports stripping the VLAN tag and reporting it
in metadata.
Complete the support for this.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Stevenson [Mon, 25 Jun 2018 14:07:13 +0000 (15:07 +0100)]
net: lan78xx: Add support for VLAN filtering.
HW_VLAN_CTAG_FILTER was partially implemented, but not advertised
to Linux.
Complete the implementation of this.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Stevenson [Mon, 25 Jun 2018 14:07:12 +0000 (15:07 +0100)]
net: lan78xx: Allow for VLAN headers in timeout calcs
The frame abort timeout being set by lan78xx_set_rx_max_frame_length
didn't account for any VLAN headers, resulting in very low
throughput if used with tagged VLANs.
Use VLAN_ETH_HLEN instead of ETH_HLEN to correct for this.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Slaby [Mon, 25 Jun 2018 07:26:27 +0000 (09:26 +0200)]
r8152: napi hangup fix after disconnect
When unplugging an r8152 adapter while the interface is UP, the NIC
becomes unusable. usb->disconnect (aka rtl8152_disconnect) deletes
napi. Then, rtl8152_disconnect calls unregister_netdev and that invokes
netdev->ndo_stop (aka rtl8152_close). rtl8152_close tries to
napi_disable, but the napi is already deleted by disconnect above. So
the first while loop in napi_disable never finishes. This results in
complete deadlock of the network layer as there is rtnl_mutex held by
unregister_netdev.
So avoid the call to napi_disable in rtl8152_close when the device is
already gone.
The other calls to usb_kill_urb, cancel_delayed_work_sync,
netif_stop_queue etc. seem to be fine. The urb and netdev is not
destroyed yet.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 25 Jun 2018 07:58:17 +0000 (15:58 +0800)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Fix netpoll OOPS in r8169, from Ville Syrjälä.
2) Fix bpf instruction alignment on powerpc et al., from Eric Dumazet.
3) Don't ignore IFLA_MTU attribute when creating new ipvlan links. From
Xin Long.
4) Fix use after free in AF_PACKET, from Eric Dumazet.
5) Mis-matched RTNL unlock in xen-netfront, from Ross Lagerwall.
6) Fix VSOCK loopback on big-endian, from Claudio Imbrenda.
7) Missing RX buffer offset correction when computing DMA addresses in
mvneta driver, from Antoine Tenart.
8) Fix crashes in DCCP's ccid3_hc_rx_send_feedback, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (34 commits)
sfc: make function efx_rps_hash_bucket static
strparser: Corrected typo in documentation.
qmi_wwan: add support for the Dell Wireless 5821e module
cxgb4: when disabling dcb set txq dcb priority to 0
net_sched: remove a bogus warning in hfsc
net: dccp: switch rx_tstamp_last_feedback to monotonic clock
net: dccp: avoid crash in ccid3_hc_rx_send_feedback()
net: Remove depends on HAS_DMA in case of platform dependency
MAINTAINERS: Add file patterns for dsa device tree bindings
net: mscc: make sparse happy
net: mvneta: fix the Rx desc DMA address in the Rx path
Documentation: e1000: Fix docs build error
Documentation: e100: Fix docs build error
Documentation: e1000: Use correct heading adornment
Documentation: e100: Use correct heading adornment
ipv6: mcast: fix unsolicited report interval after receiving querys
vhost_net: validate sock before trying to put its fd
VSOCK: fix loopback on big-endian systems
net: ethernet: ti: davinci_cpdma: make function cpdma_desc_pool_create static
xen-netfront: Update features after registering netdev
...
Colin Ian King [Sun, 24 Jun 2018 10:57:31 +0000 (11:57 +0100)]
sfc: make function efx_rps_hash_bucket static
The function efx_rps_hash_bucket is local to the source and
does not need to be in global scope, so make it static.
Cleans up sparse warning:
symbol 'efx_rps_hash_bucket' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 24 Jun 2018 12:54:29 +0000 (20:54 +0800)]
Linux 4.18-rc2
Linus Torvalds [Sun, 24 Jun 2018 12:29:15 +0000 (20:29 +0800)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"A pile of perf updates:
Kernel side:
- Remove an incorrect warning in uprobe_init_insn() when
insn_get_length() fails. The error return code is handled at the
call site.
- Move the inline keyword to the right place in the perf ringbuffer
code to address a W=1 build warning.
Tooling:
perf stat:
- Fix metric column header display alignment
- Improve error messages for default attributes, providing better
output for error in command line.
- Add --interval-clear option, to provide a 'watch' like printing
perf script:
- Show hw-cache events too
perf c2c:
- Fix data dependency problem in layout of 'struct c2c_hist_entry'
Core:
- Do not blindly assume that 'struct perf_evsel' can be obtained via
a straight forward container_of() as there are call sites which
hand in a plain 'struct hist' which is not part of a container.
- Fix error index in the PMU event parser, so that error messages can
point to the problematic token"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Move the inline keyword at the beginning of the function declaration
uprobes/x86: Remove incorrect WARN_ON() in uprobe_init_insn()
perf script: Show hw-cache events
perf c2c: Keep struct hist_entry at the end of struct c2c_hist_entry
perf stat: Add event parsing error handling to add_default_attributes
perf stat: Allow to specify specific metric column len
perf stat: Fix metric column header display alignment
perf stat: Use only color_fprintf call in print_metric_only
perf stat: Add --interval-clear option
perf tools: Fix error index for pmu event parser
perf hists: Reimplement hists__has_callchains()
perf hists browser gtk: Use hist_entry__has_callchains()
perf hists: Make hist_entry__has_callchains() work with 'perf c2c'
perf hists: Save the callchain_size in struct hist_entry
Linus Torvalds [Sun, 24 Jun 2018 12:18:19 +0000 (20:18 +0800)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull rseq fixes from Thomas Gleixer:
"A pile of rseq related fixups:
- Prevent infinite recursion when delivering SIGSEGV
- Remove the abort of rseq critical section on fork() as syscalls
inside rseq critical sections are explicitely forbidden. So no
point in doing the abort on the child.
- Align the rseq structure on 32 bytes in the ARM selftest code.
- Fix file permissions of the test script"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rseq: Avoid infinite recursion when delivering SIGSEGV
rseq/cleanup: Do not abort rseq c.s. in child on fork()
rseq/selftests/arm: Align 'struct rseq_cs' on 32 bytes
rseq/selftests: Make run_param_test.sh executable
Linus Torvalds [Sun, 24 Jun 2018 12:16:17 +0000 (20:16 +0800)]
Merge branch 'efi-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull EFI fixes from Thomas Gleixner:
"Two fixlets for the EFI maze:
- Properly zero variables to prevent an early boot hang on EFI mixed
mode systems
- Fix the fallout of merging the 32bit and 64bit variants of EFI PCI
related code which ended up chosing the 32bit variant of the actual
EFi call invocation which leads to failures on 64bit"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/x86: Fix incorrect invocation of PciIo->Attributes()
efi/libstub/tpm: Initialize efi_physical_addr_t vars to zero for mixed mode
Linus Torvalds [Sun, 24 Jun 2018 12:06:42 +0000 (20:06 +0800)]
Merge branch 'core-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull core fixes from Thomas Gleixner:
"Two tiny fixes:
- Add the missing machine_real_restart() to objtools noreturn list so
it stops complaining
- Fix a trivial comment typo"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kernel.h: Fix a typo in comment
objtool: Add machine_real_restart() to the noreturn list
Linus Torvalds [Sun, 24 Jun 2018 11:59:52 +0000 (19:59 +0800)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for x86:
- Make Xen PV guest deal with speculative store bypass correctly
- Address more fallout from the 5-Level pagetable handling. Undo an
__initdata annotation to avoid section mismatch and malfunction
when post init code would touch the freed variable.
- Handle exception fixup in math_error() before calling notify_die().
The reverse call order incorrectly triggers notify_die() listeners
for soemthing which is handled correctly at the site which issues
the floating point instruction.
- Fix an off by one in the LLC topology calculation on AMD
- Handle non standard memory block sizes gracefully un UV platforms
- Plug a memory leak in the microcode loader
- Sanitize the purgatory build magic
- Add the x86 specific device tree bindings directory to the x86
MAINTAINER file patterns"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Fix 'no5lvl' handling
Revert "x86/mm: Mark __pgtable_l5_enabled __initdata"
x86/CPU/AMD: Fix LLC ID bit-shift calculation
MAINTAINERS: Add file patterns for x86 device tree bindings
x86/microcode/intel: Fix memleak in save_microcode_patch()
x86/platform/UV: Add kernel parameter to set memory block size
x86/platform/UV: Use new set memory block size function
x86/platform/UV: Add adjustable set memory block size function
x86/build: Remove unnecessary preparation for purgatory
Revert "kexec/purgatory: Add clean-up for purgatory directory"
x86/xen: Add call of speculative_store_bypass_ht_init() to PV paths
x86: Call fixup_exception() before notify_die() in math_error()
Linus Torvalds [Sun, 24 Jun 2018 11:48:30 +0000 (19:48 +0800)]
Merge branch 'x86-pti-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 pti fixes from Thomas Gleixner:
"Two small updates for the speculative distractions:
- Make it more clear to the compiler that array_index_mask_nospec()
is not subject for optimizations. It's not perfect, but ...
- Don't report XEN PV guests as vulnerable because their mitigation
state depends on the hypervisor. Report unknown and refer to the
hypervisor requirement"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/spectre_v1: Disable compiler optimizations over array_index_mask_nospec()
x86/pti: Don't report XenPV as vulnerable
Linus Torvalds [Sun, 24 Jun 2018 11:36:16 +0000 (19:36 +0800)]
Merge branch 'locking-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull locking fixes from Thomas Gleixner:
"A set of fixes and updates for the locking code:
- Prevent lockdep from updating irq state within its own code and
thereby confusing itself.
- Buid fix for older GCCs which mistreat anonymous unions
- Add a missing lockdep annotation in down_read_non_onwer() which
causes up_read_non_owner() to emit a lockdep splat
- Remove the custom alpha dec_and_lock() implementation which is
incorrect in terms of ordering and use the generic one.
The remaining two commits are not strictly fixes. They provide irqsave
variants of atomic_dec_and_lock() and refcount_dec_and_lock(). These
are required to merge the relevant updates and cleanups into different
maintainer trees for 4.19, so routing them into mainline without
actual users is the sanest approach.
They should have been in -rc1, but last weekend I took the liberty to
just avoid computers in order to regain some mental sanity"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/qspinlock: Fix build for anonymous union in older GCC compilers
locking/lockdep: Do not record IRQ state within lockdep code
locking/rwsem: Fix up_read_non_owner() warning with DEBUG_RWSEMS
locking/refcounts: Implement refcount_dec_and_lock_irqsave()
atomic: Add irqsave variant of atomic_dec_and_lock()
alpha: Remove custom dec_and_lock() implementation
Linus Torvalds [Sun, 24 Jun 2018 11:22:19 +0000 (19:22 +0800)]
Merge branch 'ras-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull ras fixes from Thomas Gleixner:
"A set of fixes for RAS/MCE:
- Improve the error message when the kernel cannot recover from a MCE
so the maximum amount of information gets provided.
- Individually check MCE recovery features on SkyLake CPUs instead of
assuming none when the CAPID0 register does not advertise the
general ability for recovery.
- Prevent MCE to output inconsistent messages which first show an
error location and then claim that the source is unknown.
- Prevent overwriting MCi_STATUS in the attempt to gather more
information when a fatal MCE has alreay been detected. This leads
to empty status values in the printout and failing to react
promptly on the fatal event"
* 'ras-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Fix incorrect "Machine check from unknown source" message
x86/mce: Do not overwrite MCi_STATUS in mce_no_way_out()
x86/mce: Check for alternate indication of machine check recovery on Skylake
x86/mce: Improve error message when kernel cannot recover
Linus Torvalds [Sun, 24 Jun 2018 11:16:42 +0000 (19:16 +0800)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"A small set of fixes for time(r) related issues:
- Fix a long standing conversion issue in jiffies_to_msecs() for odd
HZ values like 1024 or 1200 which resulted in returning 0 for small
jiffies values due to rounding down.
- Use the proper CONFIG symbol in the new Y2038 safe compat code for
posix-timers. Not yet a visible breakage, but this will immediately
trigger when the architecture support for the new interfaces is
merged.
- Return an error code in the STM32 clocksource driver on failure
instead of success.
- Remove the redundant and stale irq disabled check in the posix cpu
timer code. The check is at the wrong place anyway and lockdep
already covers it via the sighand lock locking coverage"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time: Make sure jiffies_to_msecs() preserves non-zero time periods
posix-timers: Fix nanosleep_copyout() for CONFIG_COMPAT_32BIT_TIME
clocksource/drivers/stm32: Fix error return code
posix-cpu-timers: Remove lockdep_assert_irqs_disabled()
Linus Torvalds [Sun, 24 Jun 2018 11:01:18 +0000 (19:01 +0800)]
Merge branch 'irq-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A set of fixes mostly for the ARM/GIC world:
- Fix the MSI affinity handling in the ls-scfg irq chip driver so it
updates and uses the effective affinity mask correctly
- Prevent binding LPIs to offline CPUs and respect the Cavium erratum
which requires that LPIs which belong to an offline NUMA node are
not bound to a CPU on a different NUMA node.
- Free only the amount of allocated interrupts in the GIC-V2M driver
instead of trying to free log2(nrirqs).
- Prevent emitting SYNC and VSYNC targetting non existing interrupt
collections in the GIC-V3 ITS driver
- Ensure that the GIV-V3 interrupt redistributor is correctly
reprogrammed on CPU hotplug
- Remove a stale unused helper function"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqdesc: Delete irq_desc_get_msi_desc()
irqchip/gic-v3-its: Fix reprogramming of redistributors on CPU hotplug
irqchip/gic-v3-its: Only emit VSYNC if targetting a valid collection
irqchip/gic-v3-its: Only emit SYNC if targetting a valid collection
irqchip/gic-v3-its: Don't bind LPI to unavailable NUMA node
irqchip/gic-v2m: Fix SPI release on error path
irqchip/ls-scfg-msi: Fix MSI affinity handling
genirq/debugfs: Add missing IRQCHIP_SUPPORTS_LEVEL_MSI debug
Linus Torvalds [Sun, 24 Jun 2018 09:19:42 +0000 (17:19 +0800)]
Merge tag 'mips_fixes_4.18_1' of git://git./linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
"A few MIPS fixes for 4.18:
- a GPIO device name fix for a regression in v4.15-rc1.
- an errata workaround for the BCM5300X platform.
- a fix to ftrace function graph tracing, broken for a long time with
the fix applying cleanly back as far as v3.17.
- addition of read barriers to in{b,w,l,q}() functions, matching
behavior of other architectures & mirroring the equivalent addition
to read{b,w,l,q} in v4.17-rc2.
Plus changes to wire up new syscalls introduced in the 4.18 cycle:
- Restartable sequences support is added, including MIPS support in
the selftests.
- io_pgetevents is wired up"
* tag 'mips_fixes_4.18_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: Wire up io_pgetevents syscall
rseq/selftests: Implement MIPS support
MIPS: Wire up the restartable sequences (rseq) syscall
MIPS: Add syscall detection for restartable sequences
MIPS: Add support for restartable sequences
MIPS: io: Add barrier after register read in inX()
mips: ftrace: fix static function graph tracing
MIPS: BCM47XX: Enable 74K Core ExternalSync for PCIe erratum
MIPS: pb44: Fix i2c-gpio GPIO descriptor table
Vakul Garg [Sun, 24 Jun 2018 12:44:01 +0000 (18:14 +0530)]
strparser: Corrected typo in documentation.
Replaced strp_pause() with strp_unpause() to correct a seemingly copy
paste documentation mistake.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ard Biesheuvel [Sat, 23 Jun 2018 21:19:03 +0000 (23:19 +0200)]
efi/x86: Fix incorrect invocation of PciIo->Attributes()
The following commit:
2c3625cb9fa2 ("efi/x86: Fold __setup_efi_pci32() and __setup_efi_pci64() into one function")
... merged the two versions of __setup_efi_pciXX(), without taking into
account that the 32-bit version used a rather dodgy trick to pass an
immediate 0 constant as argument for a uint64_t parameter.
The issue is caused by the fact that on x86, UEFI protocol method calls
are redirected via struct efi_config::call(), which is a variadic function,
and so the compiler has to infer the types of the parameters from the
arguments rather than from the prototype.
As the 32-bit x86 calling convention passes arguments via the stack,
passing the unqualified constant 0 twice is the same as passing 0ULL,
which is why the 32-bit code in __setup_efi_pci32() contained the
following call:
status = efi_early->call(pci->attributes, pci,
EfiPciIoAttributeOperationGet, 0, 0,
&attributes);
to invoke this UEFI protocol method:
typedef
EFI_STATUS
(EFIAPI *EFI_PCI_IO_PROTOCOL_ATTRIBUTES) (
IN EFI_PCI_IO_PROTOCOL *This,
IN EFI_PCI_IO_PROTOCOL_ATTRIBUTE_OPERATION Operation,
IN UINT64 Attributes,
OUT UINT64 *Result OPTIONAL
);
After the merge, we inadvertently ended up with this version for both
32-bit and 64-bit builds, breaking the latter.
So replace the two zeroes with the explicitly typed constant 0ULL,
which works as expected on both 32-bit and 64-bit builds.
Wilfried tested the 64-bit build, and I checked the generated assembly
of a 32-bit build with and without this patch, and they are identical.
Reported-by: Wilfried Klaebe <linux-kernel@lebenslange-mailadresse.de>
Tested-by: Wilfried Klaebe <linux-kernel@lebenslange-mailadresse.de>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: hdegoede@redhat.com
Cc: linux-efi@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Aleksander Morgado [Sat, 23 Jun 2018 21:22:52 +0000 (23:22 +0200)]
qmi_wwan: add support for the Dell Wireless 5821e module
This module exposes two USB configurations: a QMI+AT capable setup on
USB config #1 and a MBIM capable setup on USB config #2.
By default the kernel will choose the MBIM capable configuration as
long as the cdc_mbim driver is available. This patch adds support for
the QMI port in the secondary configuration.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar [Sat, 23 Jun 2018 14:58:26 +0000 (20:28 +0530)]
cxgb4: when disabling dcb set txq dcb priority to 0
When we are disabling DCB, store "0" in txq->dcb_prio
since that's used for future TX Work Request "OVLAN_IDX"
values. Setting non zero priority upon disabling DCB
would halt the traffic.
Reported-by: AMG Zollner Robert <robert@cloudmedia.eu>
CC: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 23 Jun 2018 22:33:54 +0000 (06:33 +0800)]
Merge tag 'for-linus-
20180623' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- Further timeout fixes. We aren't quite there yet, so expect another
round of fixes for that to completely close some of the IRQ vs
completion races. (Christoph/Bart)
- Set of NVMe fixes from the usual suspects, mostly error handling
- Two off-by-one fixes (Dan)
- Another bdi race fix (Jan)
- Fix nbd reconfigure with NBD_DISCONNECT_ON_CLOSE (Doron)
* tag 'for-linus-
20180623' of git://git.kernel.dk/linux-block:
blk-mq: Fix timeout handling in case the timeout handler returns BLK_EH_DONE
bdi: Fix another oops in wb_workfn()
lightnvm: Remove depends on HAS_DMA in case of platform dependency
nvme-pci: limit max IO size and segments to avoid high order allocations
nvme-pci: move nvme_kill_queues to nvme_remove_dead_ctrl
nvme-fc: release io queues to allow fast fail
nbd: Add the nbd NBD_DISCONNECT_ON_CLOSE config flag.
block: sed-opal: Fix a couple off by one bugs
blk-mq-debugfs: Off by one in blk_mq_rq_state_name()
nvmet: reset keep alive timer in controller enable
nvme-rdma: don't override opts->queue_size
nvme-rdma: Fix command completion race at error recovery
nvme-rdma: fix possible free of a non-allocated async event buffer
nvme-rdma: fix possible double free condition when failing to create a controller
Revert "block: Add warning for bi_next not NULL in bio_endio()"
block: fix timeout changes for legacy request drivers
Linus Torvalds [Sat, 23 Jun 2018 22:31:54 +0000 (06:31 +0800)]
Merge branch 'linus' of git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
- Fix use after free in chtls
- Fix RBP breakage in sha3
- Fix use after free in hwrng_unregister
- Fix overread in morus640
- Move sleep out of kernel_neon in arm64/aes-blk
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
hwrng: core - Always drop the RNG in hwrng_unregister()
crypto: morus640 - Fix out-of-bounds access
crypto: don't optimize keccakf()
crypto: arm64/aes-blk - fix and move skcipher_walk_done out of kernel_neon_begin, _end
crypto: chtls - use after free in chtls_pt_recvmsg()
Linus Torvalds [Sat, 23 Jun 2018 22:26:19 +0000 (06:26 +0800)]
Merge tag 'linux-kselftest-4.18-rc2' of git://git./linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
- fix new sparc64 adi driver test compile errors on non-sparc systems
- fix config fragment for sync framework for improved test coverage
- fix several tests to return correct Kselftest skip code
* tag 'linux-kselftest-4.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: sparc64: Add missing SPDX License Identifiers
selftests: sparc64: delete RUN_TESTS and EMIT_TESTS overrides
selftests: sparc64: Fix to do nothing on non-sparc64
selftests: sync: add config fragment for testing sync framework
selftests: vm: return Kselftest Skip code for skipped tests
selftests: zram: return Kselftest Skip code for skipped tests
selftests: user: return Kselftest Skip code for skipped tests
selftests: sysctl: return Kselftest Skip code for skipped tests
selftests: static_keys: return Kselftest Skip code for skipped tests
selftests: pstore: return Kselftest Skip code for skipped tests
Linus Torvalds [Sat, 23 Jun 2018 22:23:28 +0000 (06:23 +0800)]
Merge tag 'trace-v4.18-rc1' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"This contains a few fixes and a clean up.
- a bad merge caused an "endif" to go in the wrong place in
scripts/Makefile.build
- softirq tracing fix for tracing that corrupts lockdep and causes a
false splat
- histogram documentation typo fixes
- fix a bad memory reference when passing in no filter to the filter
code
- simplify code by using the swap macro instead of open coding the
swap"
* tag 'trace-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix SKIP_STACK_VALIDATION=1 build due to bad merge with -mrecord-mcount
tracing: Fix some errors in histogram documentation
tracing: Use swap macro in update_max_tr
softirq: Reorder trace_softirqs_on to prevent lockdep splat
tracing: Check for no filter when processing event filters
Bart Van Assche [Fri, 22 Jun 2018 20:18:09 +0000 (13:18 -0700)]
blk-mq: Fix timeout handling in case the timeout handler returns BLK_EH_DONE
Make sure that RQF_TIMED_OUT is cleared when a request is reused
after a block driver timeout handler has returned BLK_EH_DONE.
Fixes: da6612673988 ("blk-mq: don't time out requests again that are in the timeout handler")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jianchao Wang <jianchao.w.wang@oracle.com>
Cc: Andrew Randrianasulu <randrianasulu@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Linus Torvalds [Sat, 23 Jun 2018 13:13:05 +0000 (21:13 +0800)]
Merge tag 'powerpc-4.18-2' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- a fix for hugetlb with 4K pages, broken by our recent changes for
split PMD PTL.
- set the correct assembler machine type on e500mc, needed since
binutils 2.26 introduced two forms for the "wait" instruction.
- a fix for potential missed TLB flushes with MADV_[FREE|DONTNEED] etc.
and THP on Power9 Radix.
- three fixes to try and make our panic handling more robust by hard
disabling interrupts, and not marking stopped CPUs as offline because
they haven't been properly offlined.
- three other minor fixes.
Thanks to: Aneesh Kumar K.V, Michael Jeanson, Nicholas Piggin.
* tag 'powerpc-4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm/hash/4k: Free hugetlb page table caches correctly.
powerpc/64s/radix: Fix radix_kvm_prefetch_workaround paca access of not possible CPU
powerpc/64s: Fix build failures with CONFIG_NMI_IPI=n
powerpc/64: hard disable irqs on the panic()ing CPU
powerpc: smp_send_stop do not offline stopped CPUs
powerpc/64: hard disable irqs in panic_smp_self_stop
powerpc/64s: Fix DT CPU features Power9 DD2.1 logic
powerpc/64s/radix: Fix MADV_[FREE|DONTNEED] TLB flush miss problem with THP
powerpc/e500mc: Set assembler machine type to e500mc
Linus Torvalds [Sat, 23 Jun 2018 13:07:43 +0000 (21:07 +0800)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- clear buffers allocated with FORCE_CONTIGUOUS explicitly until the
CMA code honours __GFP_ZERO
- notrace annotation for secondary_start_kernel()
- use early_param() instead of __setup() for "kpti=" as it is needed
for the cpufeature callback remapping swapper to non-global mappings
- ensure writes to swapper are ordered wrt subsequent cache maintenance
in the kpti non-global remapping code
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: Ensure writes to swapper are ordered wrt subsequent cache maintenance
arm64: kpti: Use early_param for kpti= command-line option
arm64: make secondary_start_kernel() notrace
arm64: dma-mapping: clear buffers allocated with FORCE_CONTIGUOUS flag
Linus Torvalds [Sat, 23 Jun 2018 12:59:00 +0000 (20:59 +0800)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"ARM:
- Lazy FPSIMD switching fixes
- Really disable compat ioctls on architectures that don't want it
- Disable compat on arm64 (it was never implemented...)
- Rely on architectural requirements for GICV on GICv3
- Detect bad alignments in unmap_stage2_range
x86:
- Add nested VM entry checks to avoid broken error recovery path
- Minor documentation fix"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: fix KVM_CAP_HYPERV_TLBFLUSH paragraph number
kvm: vmx: Nested VM-entry prereqs for event inj.
KVM: arm64: Prevent KVM_COMPAT from being selected
KVM: Enforce error in ioctl for compat tasks when !KVM_COMPAT
KVM: arm/arm64: add WARN_ON if size is not PAGE_SIZE aligned in unmap_stage2_range
KVM: arm64: Avoid mistaken attempts to save SVE state for vcpus
KVM: arm64/sve: Fix SVE trap restoration for non-current tasks
KVM: arm64: Don't mask softirq with IRQs disabled in vcpu_put()
arm64: Introduce sysreg_clear_set()
KVM: arm/arm64: Drop resource size check for GICV window
Linus Torvalds [Sat, 23 Jun 2018 12:44:11 +0000 (20:44 +0800)]
Merge tag 'for-linus-4.18-rc2-tag' of git://git./linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"This contains the following fixes/cleanups:
- the removal of a BUG_ON() which wasn't necessary and which could
trigger now due to a recent change
- a correction of a long standing bug happening very rarely in Xen
dom0 when a hypercall buffer from user land was not accessible by
the hypervisor for very short periods of time due to e.g. page
migration or compaction
- usage of EXPORT_SYMBOL_GPL() instead of EXPORT_SYMBOL() in a
Xen-related driver (no breakage possible as using those symbols
without others already exported via EXPORT-SYMBOL_GPL() wouldn't
make any sense)
- a simplification for Xen PVH or Xen ARM guests
- some additional error handling for callers of xenbus_printf()"
* tag 'for-linus-4.18-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: Remove unnecessary BUG_ON from __unbind_from_irq()
xen: add new hypercall buffer mapping device
xen/scsiback: add error handling for xenbus_printf
scsi: xen-scsifront: add error handling for xenbus_printf
xen/grant-table: Export gnttab_{alloc|free}_pages as GPL
xen: add error handling for xenbus_printf
xen: share start flags between PV and PVH
Kirill A. Shutemov [Fri, 22 Jun 2018 22:08:41 +0000 (01:08 +0300)]
x86/mm: Fix 'no5lvl' handling
early_identify_cpu() has to use early version of pgtable_l5_enabled()
that doesn't rely on cpu_feature_enabled().
Defining USE_EARLY_PGTABLE_L5 before all includes does the trick.
I lost the define in one of reworks of the original patch.
Fixes: 372fddf70904 ("x86/mm: Introduce the 'no5lvl' kernel parameter")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Link: https://lkml.kernel.org/r/20180622220841.54135-3-kirill.shutemov@linux.intel.com
Kirill A. Shutemov [Fri, 22 Jun 2018 22:08:40 +0000 (01:08 +0300)]
Revert "x86/mm: Mark __pgtable_l5_enabled __initdata"
This reverts commit
e4e961e36f063484c48bed919013c106d178995d.
We need to use early version of pgtable_l5_enabled() in
early_identify_cpu() as this code runs before cpu_feature_enabled() is
usable.
But it leads to section mismatch:
cpu_init()
load_mm_ldt()
ldt_slot_va()
LDT_BASE_ADDR
LDT_PGD_ENTRY
pgtable_l5_enabled()
__pgtable_l5_enabled
__pgtable_l5_enabled marked as __initdata, but cpu_init() is not __init.
It's fixable: early code can be isolated into a separate translation unit,
but such change collides with other work in the area. That's too much
hassle to save 4 bytes of memory.
Return __pgtable_l5_enabled back to be __ro_after_init.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Link: https://lkml.kernel.org/r/20180622220841.54135-2-kirill.shutemov@linux.intel.com
Cong Wang [Fri, 22 Jun 2018 21:33:16 +0000 (14:33 -0700)]
net_sched: remove a bogus warning in hfsc
In update_vf():
cftree_remove(cl);
update_cfmin(cl->cl_parent);
the cl_cfmin of cl->cl_parent is intentionally updated to 0
when that parent only has one child. And if this parent is
root qdisc, we could end up, in hfsc_schedule_watchdog(),
that we can't decide the next schedule time for qdisc watchdog.
But it seems safe that we can just skip it, as this watchdog is
not always scheduled anyway.
Thanks to Marco for testing all the cases, nothing is broken.
Reported-by: Marco Berizzi <pupilla@libero.it>
Tested-by: Marco Berizzi <pupilla@libero.it>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 23 Jun 2018 01:46:44 +0000 (10:46 +0900)]
Merge branch 'dccp-fixes-around-rx_tstamp_last_feedback'
Eric Dumazet says:
====================
net: dccp: fixes around rx_tstamp_last_feedback
This patch series fix some issues with rx_tstamp_last_feedback.
- Switch to monotonic clock.
- Avoid potential overflows on fast hosts/networks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 22 Jun 2018 13:44:15 +0000 (06:44 -0700)]
net: dccp: switch rx_tstamp_last_feedback to monotonic clock
To compute delays, better not use time of the day which can
be changed by admins or malicious programs.
Also change ccid3_first_li() to use s64 type for delta variable
to avoid potential overflows.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Cc: dccp@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 22 Jun 2018 13:44:14 +0000 (06:44 -0700)]
net: dccp: avoid crash in ccid3_hc_rx_send_feedback()
On fast hosts or malicious bots, we trigger a DCCP_BUG() which
seems excessive.
syzbot reported :
BUG: delta (-6195) <= 0 at net/dccp/ccids/ccid3.c:628/ccid3_hc_rx_send_feedback()
CPU: 1 PID: 18 Comm: ksoftirqd/1 Not tainted 4.18.0-rc1+ #112
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c9/0x2b4 lib/dump_stack.c:113
ccid3_hc_rx_send_feedback net/dccp/ccids/ccid3.c:628 [inline]
ccid3_hc_rx_packet_recv.cold.16+0x38/0x71 net/dccp/ccids/ccid3.c:793
ccid_hc_rx_packet_recv net/dccp/ccid.h:185 [inline]
dccp_deliver_input_to_ccids+0xf0/0x280 net/dccp/input.c:180
dccp_rcv_established+0x87/0xb0 net/dccp/input.c:378
dccp_v4_do_rcv+0x153/0x180 net/dccp/ipv4.c:654
sk_backlog_rcv include/net/sock.h:914 [inline]
__sk_receive_skb+0x3ba/0xd80 net/core/sock.c:517
dccp_v4_rcv+0x10f9/0x1f58 net/dccp/ipv4.c:875
ip_local_deliver_finish+0x2eb/0xda0 net/ipv4/ip_input.c:215
NF_HOOK include/linux/netfilter.h:287 [inline]
ip_local_deliver+0x1e9/0x750 net/ipv4/ip_input.c:256
dst_input include/net/dst.h:450 [inline]
ip_rcv_finish+0x823/0x2220 net/ipv4/ip_input.c:396
NF_HOOK include/linux/netfilter.h:287 [inline]
ip_rcv+0xa18/0x1284 net/ipv4/ip_input.c:492
__netif_receive_skb_core+0x2488/0x3680 net/core/dev.c:4628
__netif_receive_skb+0x2c/0x1e0 net/core/dev.c:4693
process_backlog+0x219/0x760 net/core/dev.c:5373
napi_poll net/core/dev.c:5771 [inline]
net_rx_action+0x7da/0x1980 net/core/dev.c:5837
__do_softirq+0x2e8/0xb17 kernel/softirq.c:284
run_ksoftirqd+0x86/0x100 kernel/softirq.c:645
smpboot_thread_fn+0x417/0x870 kernel/smpboot.c:164
kthread+0x345/0x410 kernel/kthread.c:240
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:412
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Cc: dccp@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Geert Uytterhoeven [Fri, 22 Jun 2018 11:08:43 +0000 (13:08 +0200)]
net: Remove depends on HAS_DMA in case of platform dependency
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geert Uytterhoeven [Fri, 22 Jun 2018 10:08:13 +0000 (12:08 +0200)]
MAINTAINERS: Add file patterns for dsa device tree bindings
Submitters of device tree binding documentation may forget to CC
the subsystem maintainer if this is missing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Fri, 22 Jun 2018 09:50:52 +0000 (11:50 +0200)]
net: mscc: make sparse happy
This patch fixes a sparse warning about using an incorrect type in
argument 2 of ocelot_write_rix(), as an u32 was expected but a __be32
was given. The conversion to u32 is forced, which is safe as the value
will be written as-is in the hardware without any modification.
Fixes: 08d02364b12f ("net: mscc: fix the injection header")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Fri, 22 Jun 2018 08:15:39 +0000 (10:15 +0200)]
net: mvneta: fix the Rx desc DMA address in the Rx path
When using s/w buffer management, buffers are allocated and DMA mapped.
When doing so on an arm64 platform, an offset correction is applied on
the DMA address, before storing it in an Rx descriptor. The issue is
this DMA address is then used later in the Rx path without removing the
offset correction. Thus the DMA address is wrong, which can led to
various issues.
This patch fixes this by removing the offset correction from the DMA
address retrieved from the Rx descriptor before using it in the Rx path.
Fixes: 8d5047cf9ca2 ("net: mvneta: Convert to be 64 bits compatible")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobin C. Harding [Fri, 22 Jun 2018 00:37:08 +0000 (10:37 +1000)]
Documentation: e1000: Fix docs build error
Recent patch updated e1000 docs to rst format. Docs build (`make
htmldocs`) is currently failing due to this file with error:
(SEVERE/4) Unexpected section title.
This is because a section of the file is indented 2 spaces. Build error
can be cleared by aligning the text with column 0. While we are changing
these lines we can make sure line length does not exceed 72, that
newlines following headings are uniform, and that full stops are
followed by two spaces.
Align text with column 0, limit line length to 72, ensure two spaces
follow all full stops, ensure uniform use of newlines after heading.
Fixes commit (
228046e76189 Documentation: e1000: Update kernel documentation)
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobin C. Harding [Fri, 22 Jun 2018 00:37:07 +0000 (10:37 +1000)]
Documentation: e100: Fix docs build error
Recent patch updated e100 docs to rst format. Docs build (`make
htmldocs`) is currently failing due to this file with error:
(SEVERE/4) Unexpected section title.
This is because a section of the file is indented 2 spaces. Build error
can be cleared by aligning the text with column 0. While we are changing
these lines we can make sure line length does not exceed 72, that
newlines following headings are uniform, and that full stops are
followed by two spaces.
Align text with column 0, limit line length to 72, ensure two spaces
follow all full stops, ensure uniform use of newlines after heading.
Fixes commit (
85d63445f411 Documentation: e100: Update the Intel 10/100 driver doc)
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobin C. Harding [Fri, 22 Jun 2018 00:37:06 +0000 (10:37 +1000)]
Documentation: e1000: Use correct heading adornment
Recently documentation file was converted to rst. The document title
has the incorrect heading adornment. From kernel docs:
* Please stick to this order of heading adornments:
1. ``=`` with overline for document title::
==============
Document title
==============
Add overline heading adornment to document title.
Fixes commit (
228046e76189 Documentation: e1000: Update kernel documentation)
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobin C. Harding [Fri, 22 Jun 2018 00:37:05 +0000 (10:37 +1000)]
Documentation: e100: Use correct heading adornment
Recently documentation file was converted to rst. The document title
has the incorrect heading adornment. From kernel docs:
* Please stick to this order of heading adornments:
1. ``=`` with overline for document title::
==============
Document title
==============
Add overline heading adornment to document title.
Fixes commit (
85d63445f411 Documentation: e100: Update the Intel 10/100 driver doc)
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Thu, 21 Jun 2018 11:49:36 +0000 (19:49 +0800)]
ipv6: mcast: fix unsolicited report interval after receiving querys
After recieving MLD querys, we update idev->mc_maxdelay with max_delay
from query header. This make the later unsolicited reports have the same
interval with mc_maxdelay, which means we may send unsolicited reports with
long interval time instead of default configured interval time.
Also as we will not call ipv6_mc_reset() after device up. This issue will
be there even after leave the group and join other groups.
Fixes: fc4eba58b4c14 ("ipv6: make unsolicited report intervals configurable for mld")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Thu, 21 Jun 2018 05:11:31 +0000 (13:11 +0800)]
vhost_net: validate sock before trying to put its fd
Sock will be NULL if we pass -1 to vhost_net_set_backend(), but when
we meet errors during ubuf allocation, the code does not check for
NULL before calling sockfd_put(), this will lead NULL
dereferencing. Fixing by checking sock pointer before.
Fixes: bab632d69ee4 ("vhost: vhost TX zero-copy support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suravee Suthikulpanit [Wed, 13 Jun 2018 18:43:10 +0000 (13:43 -0500)]
x86/CPU/AMD: Fix LLC ID bit-shift calculation
The current logic incorrectly calculates the LLC ID from the APIC ID.
Unless specified otherwise, the LLC ID should be calculated by removing
the Core and Thread ID bits from the least significant end of the APIC
ID. For more info, see "ApicId Enumeration Requirements" in any Fam17h
PPR document.
[ bp: Improve commit message. ]
Fixes: 68091ee7ac3c ("Calculate last level cache ID from number of sharing threads")
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1528915390-30533-1-git-send-email-suravee.suthikulpanit@amd.com
Thomas Gleixner [Fri, 22 Jun 2018 19:20:35 +0000 (21:20 +0200)]
Merge branch 'linus' into x86/urgent
Required to queue a dependent fix.
Jan Kara [Mon, 18 Jun 2018 13:46:58 +0000 (15:46 +0200)]
bdi: Fix another oops in wb_workfn()
syzbot is reporting NULL pointer dereference at wb_workfn() [1] due to
wb->bdi->dev being NULL. And Dmitry confirmed that wb->state was
WB_shutting_down after wb->bdi->dev became NULL. This indicates that
unregister_bdi() failed to call wb_shutdown() on one of wb objects.
The problem is in cgwb_bdi_unregister() which does cgwb_kill() and thus
drops bdi's reference to wb structures before going through the list of
wbs again and calling wb_shutdown() on each of them. This way the loop
iterating through all wbs can easily miss a wb if that wb has already
passed through cgwb_remove_from_bdi_list() called from wb_shutdown()
from cgwb_release_workfn() and as a result fully shutdown bdi although
wb_workfn() for this wb structure is still running. In fact there are
also other ways cgwb_bdi_unregister() can race with
cgwb_release_workfn() leading e.g. to use-after-free issues:
CPU1 CPU2
cgwb_bdi_unregister()
cgwb_kill(*slot);
cgwb_release()
queue_work(cgwb_release_wq, &wb->release_work);
cgwb_release_workfn()
wb = list_first_entry(&bdi->wb_list, ...)
spin_unlock_irq(&cgwb_lock);
wb_shutdown(wb);
...
kfree_rcu(wb, rcu);
wb_shutdown(wb); -> oops use-after-free
We solve these issues by synchronizing writeback structure shutdown from
cgwb_bdi_unregister() with cgwb_release_workfn() using a new mutex. That
way we also no longer need synchronization using WB_shutting_down as the
mutex provides it for CONFIG_CGROUP_WRITEBACK case and without
CONFIG_CGROUP_WRITEBACK wb_shutdown() can be called only once from
bdi_unregister().
Reported-by: syzbot <syzbot+4a7438e774b21ddd8eca@syzkaller.appspotmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Geert Uytterhoeven [Fri, 22 Jun 2018 11:05:35 +0000 (13:05 +0200)]
lightnvm: Remove depends on HAS_DMA in case of platform dependency
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Will Deacon [Fri, 22 Jun 2018 10:45:07 +0000 (11:45 +0100)]
rseq: Avoid infinite recursion when delivering SIGSEGV
When delivering a signal to a task that is using rseq, we call into
__rseq_handle_notify_resume() so that the registers pushed in the
sigframe are updated to reflect the state of the restartable sequence
(for example, ensuring that the signal returns to the abort handler if
necessary).
However, if the rseq management fails due to an unrecoverable fault when
accessing userspace or certain combinations of RSEQ_CS_* flags, then we
will attempt to deliver a SIGSEGV. This has the potential for infinite
recursion if the rseq code continuously fails on signal delivery.
Avoid this problem by using force_sigsegv() instead of force_sig(), which
is explicitly designed to reset the SEGV handler to SIG_DFL in the case
of a recursive fault. In doing so, remove rseq_signal_deliver() from the
internal rseq API and have an optional struct ksignal * parameter to
rseq_handle_notify_resume() instead.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: peterz@infradead.org
Cc: paulmck@linux.vnet.ibm.com
Cc: boqun.feng@gmail.com
Link: https://lkml.kernel.org/r/1529664307-983-1-git-send-email-will.deacon@arm.com
Will Deacon [Fri, 22 Jun 2018 15:23:45 +0000 (16:23 +0100)]
arm64: mm: Ensure writes to swapper are ordered wrt subsequent cache maintenance
When rewriting swapper using nG mappings, we must performance cache
maintenance around each page table access in order to avoid coherency
problems with the host's cacheable alias under KVM. To ensure correct
ordering of the maintenance with respect to Device memory accesses made
with the Stage-1 MMU disabled, DMBs need to be added between the
maintenance and the corresponding memory access.
This patch adds a missing DMB between writing a new page table entry and
performing a clean+invalidate on the same line.
Fixes: f992b4dfd58b ("arm64: kpti: Add ->enable callback to remap swapper using nG mappings")
Cc: <stable@vger.kernel.org> # 4.16.x-
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
projects / openwrt / staging / blogic.git / log