Michael Chan [Mon, 6 Feb 2017 21:55:34 +0000 (16:55 -0500)]
bnxt_en: Add bp->rx_dir field for rx buffer DMA direction.
When driver is running in XDP mode, rx buffers are DMA mapped as
DMA_BIDIRECTIONAL. Add a field so the code will map/unmap rx buffers
according to this field.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 6 Feb 2017 21:55:33 +0000 (16:55 -0500)]
bnxt_en: Don't use DEFINE_DMA_UNMAP_ADDR to store DMA address in RX path.
To support XDP_TX, we need the RX buffer's DMA address to transmit the
packet. Convert the DMA address field to a permanent field in
bnxt_sw_rx_bd.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 6 Feb 2017 21:55:32 +0000 (16:55 -0500)]
bnxt_en: Refactor rx SKB function.
Minor refactoring of bnxt_rx_skb() so that it can easily be replaced by
a new function that handles packets in a single page. Also, use a
function pointer bp->rx_skb_func() to switch to a new function when
we add the new mode in the next patch.
Add a new field data_ptr that points to the packet data in the
bnxt_sw_rx_bd structure. The original data field is changed to void
pointer so that it can either hold the kmalloc'ed data or a page
pointer.
The last parameter of bnxt_rx_skb() which was the length parameter is
changed to include the payload offset of the packet in the upper 16 bit.
The offset is needed to support the rx page mode and is not used in
this existing function.
v3: Added a new data_ptr parameter to bp->rx_skb_func(). The caller
has the option to modify the starting address of the packet. This
will be needed when XDP with headroom support is added.
v2: Changed the name of the last parameter to offset_and_len to make the
code more clear.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Timur Tabi [Mon, 6 Feb 2017 21:34:52 +0000 (15:34 -0600)]
net: qcom/emac: add ethool support for setting pause parameters
To support setting the pause parameters, the driver can no longer just
mirror the PHY. The set_pauseparam feature allows the driver to
force the setting in the MAC, regardless of how the PHY is configured.
This means that we now need to maintain an internal state for pause
frame support, and so get_pauseparam also needs to be updated.
If the interface is already running when the setting is changed, then
the interface is reset.
Note that if the MAC is configured to enable RX pause frame support
(i.e. it transmits pause frames to throttle the other end), but the
PHY is configured to block those frames, then the feature will not work.
Also some buffer size initialization code into emac_init_adapter(),
so that it lives with similar code, including the initializtion of
pause frame support.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 7 Feb 2017 18:07:56 +0000 (13:07 -0500)]
Merge branch 'replace-dst_confirm'
Julian Anastasov says:
====================
net: dst_confirm replacement
This patchset addresses the problem of neighbour
confirmation where received replies from one nexthop
can cause confirmation of different nexthop when using
the same dst. Thanks to YueHaibing <yuehaibing@huawei.com>
for tracking the dst->pending_confirm problem.
Sockets can obtain cached output route. Such
routes can be to known nexthop (rt_gateway=IP) or to be
used simultaneously for different nexthop IPs by different
subnet prefixes (nh->nh_scope = RT_SCOPE_HOST, rt_gateway=0).
At first look, there are more problems:
- dst_confirm() sets flag on dst and not on dst->path,
as result, indication is lost when XFRM is used
- DNAT can change the nexthop, so the really used nexthop is
not confirmed
So, the following solution is to avoid using
dst->pending_confirm.
The current dst_confirm() usage is as follows:
Protocols confirming dst on received packets:
- TCP (1 dst per socket)
- SCTP (1 dst per transport)
- CXGB*
Protocols supporting sendmsg with MSG_CONFIRM [ | MSG_PROBE ] to
confirm neighbour:
- UDP IPv4/IPv6
- ICMPv4 PING
- RAW IPv4/IPv6
- L2TP/IPv6
MSG_CONFIRM for other purposes (fix not needed):
- CAN
Sending without locking the socket:
- UDP (when no cork)
- RAW (when hdrincl=1)
Redirects from old to new GW:
- rt6_do_redirect
The patchset includes the following changes:
1. sock: add sk_dst_pending_confirm flag
- used only by TCP with patch 4 to remember the received
indication in sk->sk_dst_pending_confirm
2. net: add dst_pending_confirm flag to skbuff
- skb->dst_pending_confirm will be used by all protocols
in following patches, via skb_{set,get}_dst_pending_confirm
3. sctp: add dst_pending_confirm flag
- SCTP uses per-transport dsts and can not use
sk->sk_dst_pending_confirm like TCP
4. tcp: replace dst_confirm with sk_dst_confirm
5. net: add confirm_neigh method to dst_ops
- IPv4 and IPv6 provision for slow neigh lookups for MSG_PROBE users.
I decided to use neigh lookup only for this case because on
MSG_PROBE the skb may pass MTU checks but it does not reach
the neigh confirmation code. This patch will be used from patch 6.
- xfrm_confirm_neigh: we use the last tunnel address, if present.
When there are only transports, the original dest address is used.
6. net: use dst_confirm_neigh for UDP, RAW, ICMP, L2TP
- dst_confirm conversion for UDP, RAW, ICMP and L2TP/IPv6
- these protocols use MSG_CONFIRM propagated by ip*_append_data
to skb->dst_pending_confirm. sk->sk_dst_pending_confirm is not
used because some sending paths do not lock the socket. For
MSG_PROBE we use the slow lookup (dst_confirm_neigh).
- there are also 2 cases that need the slow lookup:
__ip6_rt_update_pmtu and rt6_do_redirect. I hope
&ipv6_hdr(skb)->saddr is the correct nexthop address to use here.
7. net: pending_confirm is not used anymore
- I failed to understand the CXGB* code, I see dst_confirm()
calls but I'm not sure dst_neigh_output() was called. For now
I just removed the dst->pending_confirm flag and left all
dst_confirm() calls there. Any better idea?
- Now may be old function neigh_output() should be restored
instead of dst_neigh_output?
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Anastasov [Mon, 6 Feb 2017 21:14:17 +0000 (23:14 +0200)]
net: pending_confirm is not used anymore
When same struct dst_entry can be used for many different
neighbours we can not use it for pending confirmations.
As last step, we can remove the pending_confirm flag.
Reported-by: YueHaibing <yuehaibing@huawei.com>
Fixes: 5110effee8fd ("net: Do delayed neigh confirmation.")
Fixes: f2bb4bedf35d ("ipv4: Cache output routes in fib_info nexthops.")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Anastasov [Mon, 6 Feb 2017 21:14:16 +0000 (23:14 +0200)]
net: use dst_confirm_neigh for UDP, RAW, ICMP, L2TP
When same struct dst_entry can be used for many different
neighbours we can not use it for pending confirmations.
The datagram protocols can use MSG_CONFIRM to confirm the
neighbour. When used with MSG_PROBE we do not reach the
code where neighbour is confirmed, so we have to do the
same slow lookup by using the dst_confirm_neigh() helper.
When MSG_PROBE is not used, ip_append_data/ip6_append_data
will set the skb flag dst_pending_confirm.
Reported-by: YueHaibing <yuehaibing@huawei.com>
Fixes: 5110effee8fd ("net: Do delayed neigh confirmation.")
Fixes: f2bb4bedf35d ("ipv4: Cache output routes in fib_info nexthops.")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Anastasov [Mon, 6 Feb 2017 21:14:15 +0000 (23:14 +0200)]
net: add confirm_neigh method to dst_ops
Add confirm_neigh method to dst_ops and use it from IPv4 and IPv6
to lookup and confirm the neighbour. Its usage via the new helper
dst_confirm_neigh() should be restricted to MSG_PROBE users for
performance reasons.
For XFRM prefer the last tunnel address, if present. With help
from Steffen Klassert.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Anastasov [Mon, 6 Feb 2017 21:14:14 +0000 (23:14 +0200)]
tcp: replace dst_confirm with sk_dst_confirm
When same struct dst_entry can be used for many different
neighbours we can not use it for pending confirmations.
Use the new sk_dst_confirm() helper to propagate the
indication from received packets to sock_confirm_neigh().
Reported-by: YueHaibing <yuehaibing@huawei.com>
Fixes: 5110effee8fd ("net: Do delayed neigh confirmation.")
Fixes: f2bb4bedf35d ("ipv4: Cache output routes in fib_info nexthops.")
Tested-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Anastasov [Mon, 6 Feb 2017 21:14:13 +0000 (23:14 +0200)]
sctp: add dst_pending_confirm flag
Add new transport flag to allow sockets to confirm neighbour.
When same struct dst_entry can be used for many different
neighbours we can not use it for pending confirmations.
The flag is propagated from transport to every packet.
It is reset when cached dst is reset.
Reported-by: YueHaibing <yuehaibing@huawei.com>
Fixes: 5110effee8fd ("net: Do delayed neigh confirmation.")
Fixes: f2bb4bedf35d ("ipv4: Cache output routes in fib_info nexthops.")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Anastasov [Mon, 6 Feb 2017 21:14:12 +0000 (23:14 +0200)]
net: add dst_pending_confirm flag to skbuff
Add new skbuff flag to allow protocols to confirm neighbour.
When same struct dst_entry can be used for many different
neighbours we can not use it for pending confirmations.
Add sock_confirm_neigh() helper to confirm the neighbour and
use it for IPv4, IPv6 and VRF before dst_neigh_output.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Anastasov [Mon, 6 Feb 2017 21:14:11 +0000 (23:14 +0200)]
sock: add sk_dst_pending_confirm flag
Add new sock flag to allow sockets to confirm neighbour.
When same struct dst_entry can be used for many different
neighbours we can not use it for pending confirmations.
As not all call paths lock the socket use full word for
the flag.
Add sk_dst_confirm as replacement for dst_confirm when
called for received packets.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Mon, 6 Feb 2017 21:01:16 +0000 (13:01 -0800)]
net: phy: bcm7xxx: Add BCM74371 PHY ID
Add the BCM74371 PHY ID to the list of supported chips. This is a 28nm
technology Gigabit PHY SoC.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Mon, 6 Feb 2017 16:26:30 +0000 (17:26 +0100)]
mlxsw: add psample dependency for spectrum
When PSAMPLE is a loadable module, spectrum must not be built-in:
drivers/net/built-in.o: In function `mlxsw_sp_rx_listener_sample_func':
spectrum.c:(.text+0xe357e): undefined reference to `psample_sample_packet'
This adds a Kconfig dependency to enforce usable configurations.
Fixes: 98d0f7b9acda ("mlxsw: spectrum: Add packet sample offloading support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Yotam Gigi <yotamg@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Mon, 6 Feb 2017 16:15:05 +0000 (16:15 +0000)]
ipv6: sr: fix non static symbol warnings
Fixes the following sparse warnings:
net/ipv6/seg6_iptunnel.c:58:5: warning:
symbol 'nla_put_srh' was not declared. Should it be static?
net/ipv6/seg6_iptunnel.c:238:5: warning:
symbol 'seg6_input' was not declared. Should it be static?
net/ipv6/seg6_iptunnel.c:254:5: warning:
symbol 'seg6_output' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Mon, 6 Feb 2017 16:07:13 +0000 (16:07 +0000)]
net/sched: act_mirred: remove duplicated include from act_mirred.c
Remove duplicated include.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Mon, 6 Feb 2017 15:26:17 +0000 (15:26 +0000)]
net: wan: slic_ds26522: Remove .owner field for driver
Remove .owner field if calls are used which set it automatically.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Mon, 6 Feb 2017 15:25:52 +0000 (15:25 +0000)]
net: wan: slic_ds26522: Use module_spi_driver to simplify the code
module_spi_driver() makes the code simpler by eliminating
boilerplate code.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 7 Feb 2017 15:51:48 +0000 (10:51 -0500)]
Merge branch 'dsa2-pdata'
Florian Fainelli says:
====================
net: dsa: Support for pdata in dsa2
This is not exactly new, and was sent before, although back then, I did not
have an user of the pre-declared MDIO board information, but now we do. Note
that I have additional changes queued up to have b53 register platform data for
MIPS bcm47xx and bcm63xx.
Yes I know that we should have the Orion platforms eventually be converted to
Device Tree, but until that happens, I don't want any remaining users of the
old "dsa" platform device (hence the previous DTS submissions for ARM/mvebu)
and, there will be platforms out there that most likely won't never see DT
coming their way (BCM47xx is almost 100% sure, BCM63xx maybe not in a distant
future).
We would probably want the whole series to be merged via David Miller's tree
to simplify things.
Thanks!
Changes in v5:
- dropped changes to drivers/base/ because after more than a month, we cannot
get any answer from Greg KH
Changes in v4:
- Changed device_find_class() to device_find_in_class_name()
- Added kerneldoc above device_find_in_class_name() to explain what it does
and the calling convention regarding device reference counts
- Changed dev_to_net_device to device_to_net_device() added comments
about what it does and the caller conventions regarding reference counts
Changes in v3:
- Tested EPROBE_DEFER from a mockup MDIO/DSA switch driver and everything
is fine, once the driver finally probes we have access to platform data
as expected
- added comment above dsa_port_is_valid() that port->name is mandatory
for platform data cases
- added an extra check in dsa_parse_member() for a NULL pdata pointer
- fixed a bunch of checkpatch errors and warnings
Changes in v2:
- Rebased against latest net-next/master
- Moved dev_find_class() to device_find_class() into drivers/base/core.c
- Moved dev_to_net_device into net/core/dev.c
- Utilize dsa_chip_data directly instead of dsa_platform_data
- Augmented dsa_chip_data to be multi-CPU port ready
Changes from last submission (few months back):
- rebased against latest net-next
- do not introduce dsa2_platform_data which was overkill and was meant to
allow us to do exaclty the same things with platform data and Device Tree
we use the existing dsa_platform_data instead
- properly register MDIO devices when the MDIO bus is registered and associate
platform_data with them
- add a change to the Orion platform code to demonstrate how this can be used
Thank you
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Sat, 4 Feb 2017 21:02:45 +0000 (13:02 -0800)]
ARM: orion: Register DSA switch as a MDIO device
Utilize the ability to pass board specific MDIO bus information towards a
particular MDIO device thus allowing us to provide the per-port switch layout
to the Marvell 88E6XXX switch driver.
Since we would end-up with conflicting registration paths, do not register the
"dsa" platform device anymore.
Note that the MDIO devices registered by code in net/dsa/dsa2.c does not
parse a dsa_platform_data, but directly take a dsa_chip_data (specific
to a single switch chip), so we update the different call sites to pass
this structure down to orion_ge00_switch_init().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Sat, 4 Feb 2017 21:02:44 +0000 (13:02 -0800)]
net: phy: Allow pre-declaration of MDIO devices
Allow board support code to collect pre-declarations for MDIO devices by
registering them with mdiobus_register_board_info(). SPI and I2C buses
have a similar feature, we were missing this for MDIO devices, but this
is particularly useful for e.g: MDIO-connected switches which need to
provide their port layout (often board-specific) to a MDIO Ethernet
switch driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Sat, 4 Feb 2017 21:02:43 +0000 (13:02 -0800)]
net: dsa: Add support for platform data
Allow drivers to use the new DSA API with platform data. Most of the
code in net/dsa/dsa2.c does not rely so much on device_nodes and can get
the same information from platform_data instead.
We purposely do not support distributed configurations with platform
data, so drivers should be providing a pointer to a 'struct
dsa_chip_data' structure if they wish to communicate per-port layout.
Multiple CPUs port could potentially be supported and dsa_chip_data is
extended to receive up to one reference to an upstream network device
per port described by a dsa_chip_data structure.
dsa_dev_to_net_device() increments the network device's reference count,
so we intentionally call dev_put() to be consistent with the DT-enabled
path, until we have a generic notifier based solution.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Sat, 4 Feb 2017 21:02:42 +0000 (13:02 -0800)]
net: dsa: Rename and export dev_to_net_device()
In preparation for using this function in net/dsa/dsa2.c, rename the function
to make its scope DSA specific, and export it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sat, 4 Feb 2017 19:15:28 +0000 (20:15 +0100)]
net: dsa: mv88e6xxx: Refactor remaining port setup
Move the remaining port configuration code which varies per device
into port.c, using ops were necessary. This makes
mv88e6xxx_6185_family() and mv88e6xxx_6095_family() unused, so remove
them.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sat, 4 Feb 2017 19:12:24 +0000 (20:12 +0100)]
net: dsa: mv88e6xxx: Implement Clause 45 access to SMI devices
The mv88e6390 MDIO bus controllers can support for clause 45 accesses.
The internal SERDES interfaces need this, and it is likely external
10GHz PHYs will be clause 45.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 7 Feb 2017 15:34:43 +0000 (10:34 -0500)]
Merge branch 'mv88e6390-CMODE'
Andrew Lunn says:
====================
Set the CMODE for mv88e6390 ports
The mv88e6390 ports 9 & 10 allow there CMODE to be set. CMODE is part
of what linux defines as phy-mode. Add the needed phy-modes to linux,
and add code which will act upon the phy-mode property to configure
the switch port.
These patches have been posted before as part of a bigger patchset
which has now been broken up. I've added the received reviewed by
tags, and added device tree documentation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sat, 4 Feb 2017 19:02:50 +0000 (20:02 +0100)]
net: dsa: mv88e6xxx: Set the CMODE for mv88e6390 ports 9 & 10
Unlike most ports, ports 9 and 10 of the 6390X family have configurable
PHY modes. Set the mode as part of adjust_link().
Ordering is important, because the SERDES interfaces connected to
ports 9 and 10 can be split and assigned to other ports. The CMODE has
to be correctly set before the SERDES interface on another port can be
configured. Such configuration is likely to be performed in
port_enable() and port_disabled(), called on slave_open() and
slave_close().
The simple case is port 9 and 10 are used for 'CPU' or 'DSA'. In this
case, the CMODE is set via a phy-mode in dsa_cpu_dsa_setup(), which is
called early in the switch setup.
When ports 9 or 10 are used as user ports, and have a fixed-phy, when
the fixed fixed-phy is attached, dsa_slave_adjust_link() is called,
which results in the adjust_link function being called, setting the
cmode. The port_enable() will for other ports will be called much
later.
When ports 9 or 10 are used as user ports and have a real phy attached
which does not use all the available SERDES interface, e.g. a 1Gbps
SGMII, there is currently no mechanism in place to set the CMODE of
the port from software. It must be hoped the stripping resistors are
correct.
At the same time, add a function to get the cmode. This will be needed
when configuring the SERDES interfaces.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sat, 4 Feb 2017 19:02:49 +0000 (20:02 +0100)]
net: phy: Add 2000base-x, 2500base-x and rxaui modes
The mv88e6390 ports 9 and 10 supports some additional PHY modes. Add
these modes to the PHY core so they can be used in the binding.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 7 Feb 2017 15:05:13 +0000 (10:05 -0500)]
Merge branch 'virtio_net-XDP-adjust_head'
John Fastabend says:
====================
XDP adjust head support for virtio
This series adds adjust head support for virtio. The following is my
test setup. I use qemu + virtio as follows,
./x86_64-softmmu/qemu-system-x86_64 \
-hda /var/lib/libvirt/images/Fedora-test0.img \
-m 4096 -enable-kvm -smp 2 -netdev tap,id=hn0,queues=4,vhost=on \
-device virtio-net-pci,netdev=hn0,mq=on,guest_tso4=off,guest_tso6=off,guest_ecn=off,guest_ufo=off,vectors=9
In order to use XDP with virtio until LRO is supported TSO must be
turned off in the host. The important fields in the above command line
are the following,
guest_tso4=off,guest_tso6=off,guest_ecn=off,guest_ufo=off
Also note it is possible to conusme more queues than can be supported
because when XDP is enabled for retransmit XDP attempts to use a queue
per cpu. My standard queue count is 'queues=4'.
After loading the VM I run the relevant XDP test programs in,
./sammples/bpf
For this series I tested xdp1, xdp2, and xdp_tx_iptunnel. I usually test
with iperf (-d option to get bidirectional traffic), ping, and pktgen.
I also have a modified xdp1 that returns XDP_PASS on any packet to ensure
the normal traffic path to the stack continues to work with XDP loaded.
It would be great to automate this soon. At the moment I do it by hand
which is starting to get tedious.
v2: original series dropped trace points after merge.
====================
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Fri, 3 Feb 2017 03:16:29 +0000 (19:16 -0800)]
virtio_net: XDP support for adjust_head
Add support for XDP adjust head by allocating a 256B header region
that XDP programs can grow into. This is only enabled when a XDP
program is loaded.
In order to ensure that we do not have to unwind queue headroom push
queue setup below bpf_prog_add. It reads better to do a prog ref
unwind vs another queue setup call.
At the moment this code must do a full reset to ensure old buffers
without headroom on program add or with headroom on program removal
are not used incorrectly in the datapath. Ideally we would only
have to disable/enable the RX queues being updated but there is no
API to do this at the moment in virtio so use the big hammer. In
practice it is likely not that big of a problem as this will only
happen when XDP is enabled/disabled changing programs does not
require the reset. There is some risk that the driver may either
have an allocation failure or for some reason fail to correctly
negotiate with the underlying backend in this case the driver will
be left uninitialized. I have not seen this ever happen on my test
systems and for what its worth this same failure case can occur
from probe and other contexts in virtio framework.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Fri, 3 Feb 2017 03:16:01 +0000 (19:16 -0800)]
virtio_net: refactor freeze/restore logic into virtnet reset logic
For XDP we will need to reset the queues to allow for buffer headroom
to be configured. In order to do this we need to essentially run the
freeze()/restore() code path. Unfortunately the locking requirements
between the freeze/restore and reset paths are different however so
we can not simply reuse the code.
This patch refactors the code path and adds a reset helper routine.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Fri, 3 Feb 2017 03:15:32 +0000 (19:15 -0800)]
virtio_net: remove duplicate queue pair binding in XDP
Factor out qp assignment.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Fri, 3 Feb 2017 03:15:01 +0000 (19:15 -0800)]
virtio_net: factor out xdp handler for readability
At this point the do_xdp_prog is mostly if/else branches handling
the different modes of virtio_net. So remove it and handle running
the program in the per mode handlers.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Fri, 3 Feb 2017 03:14:32 +0000 (19:14 -0800)]
virtio_net: wrap rtnl_lock in test for calling with lock already held
For XDP use case and to allow ethtool reset tests it is useful to be
able to use reset paths from contexts where rtnl lock is already
held.
This requries updating virtnet_set_queues and free_receive_bufs the
two places where rtnl_lock is taken in virtio_net. To do this we
use the following pattern,
_foo(...) { do stuff }
foo(...) { rtnl_lock(); _foo(...); rtnl_unlock()};
this allows us to use freeze()/restore() flow from both contexts.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 7 Feb 2017 03:53:14 +0000 (22:53 -0500)]
Merge branch 'bridge-improve-cache-utilization'
Nikolay Aleksandrov says:
====================
bridge: improve cache utilization
This is the first set which begins to deal with the bad bridge cache
access patterns. The first patch rearranges the bridge and port structs
a little so the frequently (and closely) accessed members are in the same
cache line. The second patch then moves the garbage collection to a
workqueue trying to improve system responsiveness under load (many fdbs)
and more importantly removes the need to check if the matched entry is
expired in __br_fdb_get which was a major source of false-sharing.
The third patch is a preparation for the final one which
If properly configured, i.e. ports bound to CPUs (thus updating "updated"
locally) then the bridge's HitM goes from 100% to 0%, but even without
binding we get a win because previously every lookup that iterated over
the hash chain caused false-sharing due to the first cache line being
used for both mac/vid and used/updated fields.
Some results from tests I've run:
(note that these were run in good conditions for the baseline, everything
ran on a single NUMA node and there were only 3 fdbs)
1. baseline
100% Load HitM on the fdbs (between everyone who has done lookups and hit
one of the 3 hash chains of the communicating
src/dst fdbs)
Overall 5.06% Load HitM for the bridge, first place in the list
2. patched & ports bound to CPUs
0% Local load HitM, bridge is not even in the c2c report list
Also there's 3% consistent improvement in netperf tests.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Sat, 4 Feb 2017 17:05:09 +0000 (18:05 +0100)]
bridge: fdb: write to used and updated at most once per jiffy
Writing once per jiffy is enough to limit the bridge's false sharing.
After this change the bridge doesn't show up in the local load HitM stats.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Sat, 4 Feb 2017 17:05:08 +0000 (18:05 +0100)]
bridge: move write-heavy fdb members in their own cache line
Fdb's used and updated fields are written to on every packet forward and
packet receive respectively. Thus if we are receiving packets from a
particular fdb, they'll cause false-sharing with everyone who has looked
it up (even if it didn't match, since mac/vid share cache line!). The
"used" field is even worse since it is updated on every packet forward
to that fdb, thus the standard config where X ports use a single gateway
results in 100% fdb false-sharing. Note that this patch does not prevent
the last scenario, but it makes it better for other bridge participants
which are not using that fdb (and are only doing lookups over it).
The point is with this move we make sure that only communicating parties
get the false-sharing, in a later patch we'll show how to avoid that too.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Sat, 4 Feb 2017 17:05:07 +0000 (18:05 +0100)]
bridge: move to workqueue gc
Move the fdb garbage collector to a workqueue which fires at least 10
milliseconds apart and cleans chain by chain allowing for other tasks
to run in the meantime. When having thousands of fdbs the system is much
more responsive. Most importantly remove the need to check if the
matched entry has expired in __br_fdb_get that causes false-sharing and
is completely unnecessary if we cleanup entries, at worst we'll get 10ms
of traffic for that entry before it gets deleted.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Sat, 4 Feb 2017 17:05:06 +0000 (18:05 +0100)]
bridge: modify bridge and port to have often accessed fields in one cache line
Move around net_bridge so the vlan fields are in the beginning since
they're checked on every packet even if vlan filtering is disabled.
For the port move flags & vlan group to the beginning, so they're in the
same cache line with the port's state (both flags and state are checked
on each packet).
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
William Tu [Sat, 4 Feb 2017 16:37:29 +0000 (08:37 -0800)]
bpf: enable verifier to add 0 to packet ptr
The patch fixes the case when adding a zero value to the packet
pointer. The zero value could come from src_reg equals type
BPF_K or CONST_IMM. The patch fixes both, otherwise the verifer
reports the following error:
[...]
R0=imm0,min_value=0,max_value=0
R1=pkt(id=0,off=0,r=4)
R2=pkt_end R3=fp-12
R4=imm4,min_value=4,max_value=4
R5=pkt(id=0,off=4,r=4)
269: (bf) r2 = r0 // r2 becomes imm0
270: (77) r2 >>= 3
271: (bf) r4 = r1 // r4 becomes pkt ptr
272: (0f) r4 += r2 // r4 += 0
addition of negative constant to packet pointer is not allowed
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: Mihai Budiu <mbudiu@vmware.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Josef Bacik [Fri, 3 Feb 2017 21:25:23 +0000 (16:25 -0500)]
bpf: test for AND edge cases
These two tests are based on the work done for
f23cc643f9ba. The first test is
just a basic one to make sure we don't allow AND'ing negative values, even if it
would result in a valid index for the array. The second is a cleaned up version
of the original testcase provided by Jann Horn that resulted in the commit.
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 6 Feb 2017 21:53:30 +0000 (16:53 -0500)]
Merge branch 'dsa-add-fabric-notifier'
Vivien Didelot says:
====================
net: dsa: add fabric notifier
When a switch fabric is composed of multiple switch chips, these chips
must be programmed accordingly when an event occurred on one of them.
Examples of such event include hardware bridging: when a Linux bridge
spans interconnected chips, they must be programmed to allow external
ports to ingress frames on their internal ports.
Another example is cross-chip hardware VLANs. Switch chips in-between
interconnected bridge ports must also configure a given VLAN to allow
packets to pass through them.
In order to support that, this patchset introduces a non-intrusive
notifier mechanism. It adds a notifier head in every DSA switch tree
(the said fabric), and a notifier block in every DSA switch chip.
When an even occurs, it is chained to all notifiers of the fabric.
Switch chips can react accordingly if they are cross-chip capable.
On a dynamic debug enabled system, bridging a port in a multi-chip
fabric will print something like this (ZII Rev B board):
# brctl addif br0 lan3
mv88e6085 0.1:00: crosschip DSA port 1.0 bridged to br0
mv88e6085 0.4:00: crosschip DSA port 1.0 bridged to br0
# brctl delif br0 lan3
mv88e6085 0.1:00: crosschip DSA port 1.0 unbridged from br0
mv88e6085 0.4:00: crosschip DSA port 1.0 unbridged from br0
Currently only bridging events are added. A patchset introducing support
for cross-chip hardware bridging configuration in mv88e6xxx will follow
right after. Then events for switchdev operations are next on the line.
We should note that non-switchdev events do not support rolling-back
switch-wide operations. We'll have to work on closer integration with
switchdev for that, like introducing new attributes or objects, to
benefit from the prepare and commit phases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Fri, 3 Feb 2017 18:20:21 +0000 (13:20 -0500)]
net: dsa: introduce bridge notifier
A slave device will now notify the switch fabric once its port is
bridged or unbridged, instead of calling directly its switch operations.
This code allows propagating cross-chip bridging events in the fabric.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Fri, 3 Feb 2017 18:20:20 +0000 (13:20 -0500)]
net: dsa: add switch notifier
Add a notifier block per DSA switch, registered against a notifier head
in the switch fabric they belong to.
This infrastructure will allow to propagate fabric-wide events such as
port bridging, VLAN configuration, etc. If a DSA switch driver cares
about cross-chip configuration, such events can be caught.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Fri, 3 Feb 2017 18:20:19 +0000 (13:20 -0500)]
net: dsa: change state setter scope
The scope of the functions inside net/dsa/slave.c must be the slave
net_device pointer. Change to state setter helper accordingly to
simplify callers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Fri, 3 Feb 2017 18:20:18 +0000 (13:20 -0500)]
net: dsa: rollback bridging on error
When an error is returned during the bridging of a port in a
NETDEV_CHANGEUPPER event, net/core/dev.c rolls back the operation.
Be consistent and unassign dp->bridge_dev when this happens.
In the meantime, add comments to document this behavior.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Fri, 3 Feb 2017 18:20:17 +0000 (13:20 -0500)]
net: dsa: simplify netdevice events handling
Simplify the code handling the slave netdevice notifier call by
providing a dsa_slave_changeupper helper for NETDEV_CHANGEUPPER, and so
on (only this event is supported at the moment.)
Return NOTIFY_DONE when we did not care about an event, and NOTIFY_OK
when we were concerned but no error occurred, as the API suggests.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Fri, 3 Feb 2017 18:20:16 +0000 (13:20 -0500)]
net: dsa: move netdevice notifier registration
Move the netdevice notifier block register code in slave.c and provide
helpers for dsa.c to register and unregister it.
At the same time, check for errors since (un)register_netdevice_notifier
may fail.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Fri, 3 Feb 2017 16:37:03 +0000 (17:37 +0100)]
net/mlx5e: fix another maybe-uninitialized false-positive
In commit
abeffce ("net/mlx5e: Fix a -Wmaybe-uninitialized warning"), I fixed a
gcc warning for the ipv4 offload handling. Now we get the same warning for the
added ipv6 support:
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:815:40: warning: 'out_dev' may be used uninitialized in this function [-Wmaybe-uninitialized]
We can apply the same workaround here as well.
Fixes: ce99f6b97fcd ("net/mlx5e: Support SRIOV TC encapsulation offloads for IPv6 tunnels")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parav Pandit [Sat, 4 Feb 2017 17:00:49 +0000 (11:00 -0600)]
net-next: treewide use is_vlan_dev() helper function.
This patch makes use of is_vlan_dev() function instead of flag
comparison which is exactly done by is_vlan_dev() helper function.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Jon Maxwell <jmaxwell37@gmail.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Fri, 3 Feb 2017 09:54:59 +0000 (12:54 +0300)]
net/mlx4_en: fix a condition
There is a "||" vs "|" typo here so we test 0x1 instead of 0x6.
Fixes: 1f8176f7352a ("net/mlx4_en: Check the enabling pptx/pprx flags in SET_PORT wrapper flow")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bert Kenward [Mon, 6 Feb 2017 16:50:55 +0000 (16:50 +0000)]
sfc: don't rearm interrupts if busy polling
Since commit
364b6055738b ("net: busy-poll: return busypolling status
to drivers"), napi_complete_done() returns a boolean that can be used
by drivers to conditionally rearm interrupts.
Testing with a 7142 shows a small latency improvement of ~100 ns.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Fri, 3 Feb 2017 09:37:06 +0000 (17:37 +0800)]
sctp: process fwd tsn chunk only when prsctp is enabled
This patch is to check if asoc->peer.prsctp_capable is set before
processing fwd tsn chunk, if not, it will return an ERROR to the
peer, just as rfc3758 section 3.3.1 demands.
Reported-by: Julian Cordes <julian.cordes@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 6 Feb 2017 16:25:58 +0000 (11:25 -0500)]
Merge branch 'mlxsw-cleanup-neigh-handling'
Jiri Pirko says:
====================
mlxsw: cleanup neigh handling
Ido says:
This series addresses long standing issues in the mlxsw driver
concerning neighbour reflection. It also prepares the code for follow-up
changes dealing with proper resource cleanup and nexthop reflection.
The first two patches convert the neighbour reflection code to use an
ordered workqueue, to prevent re-ordering of NEIGH_UPDATE events that
may happen following subsequent patches.
The third to fifth patches remove the ndo_neigh_{construct,destroy}
entry points from the driver, thereby relying only on NEIGH_UPDATE
events for neighbour reflection. This simplifies the code considerably.
Last patches are fallout and adjust nits in the code I noticed while
going over it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 6 Feb 2017 15:20:17 +0000 (16:20 +0100)]
mlxsw: spectrum_router: Fix typo in comment
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 6 Feb 2017 15:20:16 +0000 (16:20 +0100)]
mlxsw: spectrum_router: Don't read 'nud_state' without lock
We periodically ask the neighbouring system to try and resolve
neighbours that are used for nexthops, but aren't currently resolved.
However, 'nud_state' is protected by the neighbour lock, so we shouldn't
access it without taking it. Instead, we can simply check the
'connected' field of the neighbour entry, which we update upon
NEIGH_UPDATE events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 6 Feb 2017 15:20:15 +0000 (16:20 +0100)]
mlxsw: spectrum_router: Remove redundant check
We only add neighbour entries that are also used for nexthops to
'nexthop_neighs_list', so when iterating over this list there's no need
to check that the entry is indeed used for nexthops.
Remove the redundant check.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 6 Feb 2017 15:20:14 +0000 (16:20 +0100)]
net: remove ndo_neigh_{construct, destroy} from stacked devices
In commit
18bfb924f000 ("net: introduce default neigh_construct/destroy
ndo calls for L2 upper devices") we added these ndos to stacked devices
such as team and bond, so that calls will be propagated to mlxsw.
However, previous commit removed the reliance on these ndos and no new
users of these ndos have appeared since above mentioned commit. We can
therefore safely remove this dead code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 6 Feb 2017 15:20:13 +0000 (16:20 +0100)]
mlxsw: spectrum_router: Simplify neighbour reflection
Up until now we had two interfaces for neighbour related configuration:
ndo_neigh_{construct,destroy} and NEIGH_UPDATE netevents. The ndos were
used to add and remove neighbours from the driver's cache, whereas the
netevent was used to reflect the neighbours into the device's tables.
However, if the NUD state of a neighbour isn't NUD_VALID or if the
neighbour is dead, then there's really no reason for us to keep it
inside our cache. The only exception to this rule are neighbours that
are also used for nexthops, which we periodically refresh to get them
resolved.
We can therefore eliminate the ndo entry point into the driver and
simplify the code, making it similar to the FIB reflection, which is
based solely on events. This also helps us avoid a locking issue, in
which the RIF cache was traversed without proper locking during
insertion into the neigh entry cache.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 6 Feb 2017 15:20:12 +0000 (16:20 +0100)]
mlxsw: spectrum_router: Remove unused variable
Since commit
33b1341cd1bf ("mlxsw: spectrum_router: Fix handling of
neighbour structure") we no longer use destination IP for neighbour
lookup, so remove it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 6 Feb 2017 15:20:11 +0000 (16:20 +0100)]
mlxsw: spectrum_router: Use ordered workqueue for neigh updates
We currently associate each neighbour entry with a work item, so it's
not possible to have multiple events queued for the same neighbour
entry. However, this is about to be changed so that the neighbour entry
is only resolved when the work item is scheduled.
The above can result in a mismatch between the kernel's and the device's
neighbour table, unless the associated work items are processed in the
order in which they were submitted.
Do that by migrating the NEIGH_UPDATE work items to be processed in the
ordered workqueue which was recently introduced in mlxsw in commit
a3832b31898f ("mlxsw: core: Create an ordered workqueue for FIB
offload").
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 6 Feb 2017 15:20:10 +0000 (16:20 +0100)]
mlxsw: core: Queue work immediately instead of delaying it
We always use zero delay before queueing a work on the ordered workqueue
('mlxsw_owq'), so use work_struct directly instead of delayable work.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 6 Feb 2017 16:08:51 +0000 (11:08 -0500)]
Merge tag 'linux-can-next-for-4.11-
20170206' of git://git./linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2017-02-06
this is a pull request of 16 patches for net-next/master.
The first two patches by David Jander and me add the rx-offload
framework for CAN devices to the kernel. The remaining 14 patches
convert the flexcan driver to make use of it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Elad Raz [Mon, 6 Feb 2017 12:56:27 +0000 (13:56 +0100)]
mlxsw: reg: Fix HTGT register length
HTGT register length is limited to 32 bytes and not 256 bytes.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingju Hou [Mon, 6 Feb 2017 06:58:13 +0000 (14:58 +0800)]
net: mvneta: implement .set_wol and .get_wol
The mvneta itself does not support WOL, but the PHY might.
So pass the calls to the PHY
Signed-off-by: Jingju Hou <houjingj@marvell.com>
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde [Tue, 1 Sep 2015 08:28:46 +0000 (10:28 +0200)]
can: flexcan: switch imx6 and vf610 to timestamp based offloading
This patch switches the imx6 and vf610 based SoCs from the hardware FIFO
to the timestamp based rx offloading.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Tue, 1 Sep 2015 07:00:13 +0000 (09:00 +0200)]
can: flexcan: add support for timestamp based rx-offload
The flexcan IP core has 64 mailboxes. For now they are configured for
RX as a hardware FIFO. This FIFO has a fixed depth of 6 CAN frames. In
some high load scenarios it turns out thas this buffer is too small.
In order to have a buffer larger than the 6 frames FIFO, this patch adds
support for timestamp based offloading via the generic rx-offload
infrastructure.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Tue, 1 Sep 2015 06:57:55 +0000 (08:57 +0200)]
can: flexcan: add quirk FLEXCAN_QUIRK_ENABLE_EACEN_RRS
In order to receive RTR frames in the non HW FIFO mode the RSS and EACEN bits
of the reg_ctrl2 have to be activated. As this has no side effect in the FIFO
mode, we do this unconditionally on cores with the reg_ctrl2.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Mon, 31 Aug 2015 19:03:29 +0000 (21:03 +0200)]
can: flexcan: activate individual RX masking and initialize reg_rximr
Modern flexcan IP cores support two RX modes. One is using the 6 fames deep
hardware FIFO, the other is using up to 64 mailboxes (in non FIFO mode). For
now only the HW FIFO mode is activated.
In order to make use of the RX mailboxes the individual RX masking feature has
to be activated, otherwise matching mailboxes are overwritten during the
reception process. This however switches on the individual RX masking, which
uses reg_rximr registers for masking.
This patch activates the individual RX masking feature unconditionally and
initializes the mask registers (reg_rximr) with 0x0 == "don't care", which
switches off any filtering.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Sun, 10 May 2015 13:26:58 +0000 (15:26 +0200)]
can: flexcan: make use of rx-offload's irq_offload_fifo
This patch converts the flexcan driver to make use of the rx-offload
can_rx_offload_irq_offload_fifo() helper function. The idea is to read
the CAN frames already in the interrupt context, as the depth of the
flexcan HW FIFO is too shallow, resulting in too many missed frames.
During a normal NAPI poll the frames are the pushed into the upper
layers.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Sat, 11 Jul 2015 22:47:47 +0000 (00:47 +0200)]
can: flexcan: make TX mailbox selectable during runtime
This patch makes the TX mailbox selectable duing runtime. This is a preparation
patch to use of the hardware FIFO selectable via runtime. As the TX mailbox
number is different in HW FIFO and normal mode.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Tue, 4 Aug 2015 11:46:10 +0000 (13:46 +0200)]
can: flexcan: calculate default value for imask1 during runtime
This patch converts the define FLEXCAN_IFLAG_DEFAULT into the runtime
calculated value priv->reg_imask1_default. This is a preparation patch to make
the TX mailbox selectable during runtime, too.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Wed, 18 Jan 2017 10:45:14 +0000 (11:45 +0100)]
can: flexcan: flexcan_irq(): don't unconditionally return IRQ_HANDLED
This patch changes the flexcan_irq() function to only return
IRQ_HANDLED, if the interrupt really has been handled, otherwise
IRQ_NONE is returned.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Wed, 18 Jan 2017 10:38:26 +0000 (11:38 +0100)]
can: flexcan: flexcan_poll_bus_err(): fold in do_bus_err()
This patch folds in the do_bus_err() function into
flexcan_poll_bus_err().
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Wed, 18 Jan 2017 10:25:41 +0000 (11:25 +0100)]
can: flexcan: flexcan_poll_state(): no need to initialize new_state, rx_state, tx_state
This patch removed the not needed initialisation from the new_state,
rx_state, tx_state variabled.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Tue, 17 Jan 2017 16:33:46 +0000 (17:33 +0100)]
can: flexcan: do_bus_err(): convert rx_,tx_errors into bool
This patch converts the rx_errors and tx_errors from int into bool
values, to reflect their actual meaning.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Mon, 4 Jul 2016 12:45:44 +0000 (14:45 +0200)]
can: flexcan: make declaration of devtype_data const
This patch changes the declaration of the devtype data to const.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Mon, 4 Jul 2016 12:43:53 +0000 (14:43 +0200)]
can: flexcan: remove write-only member pdata of struct flexcan_priv
This patch removes the write only member pdata from the struct
flexcan_priv.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Thu, 27 Aug 2015 14:01:27 +0000 (16:01 +0200)]
can: flexcan: add missing register definitions
This patch adds some missing register definitions, which are needed in an
upcoming patch.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Tue, 23 Sep 2014 13:28:21 +0000 (15:28 +0200)]
can: rx-offload: Add support for timestamp based irq offloading
Some CAN controllers don't implement a FIFO in hardware, but fill their
mailboxes in a particular order (from lowest to highest or highest to lowest).
This makes problems to read the frames in the correct order from the hardware,
as new frames might be filled into just read (low) mailboxes. This gets worse,
when following new frames are received into not read (higher) mailboxes.
On the bright side some these CAN controllers put a timestamp on each received
CAN frame. This patch adds support to offload CAN frames in interrupt context,
order them by timestamp and then transmitted in a NAPI context.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
David Jander [Fri, 10 Oct 2014 15:30:10 +0000 (17:30 +0200)]
can: rx-offload: Add support for HW fifo based irq offloading
Some CAN controllers have a usable FIFO already but can still benefit
from off-loading the CAN controller FIFO. The CAN frames of the FIFO are
read and put into a skb queue during interrupt and then transmitted in a
NAPI context.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
David S. Miller [Sun, 5 Feb 2017 21:11:59 +0000 (16:11 -0500)]
Merge branch 'remove-__napi_complete_done'
Eric Dumazet says:
====================
net: get rid of __napi_complete()
This patch series removes __napi_complete() calls, in an effort
to make NAPI API simpler and generalize GRO and napi_complete_done()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 4 Feb 2017 23:25:02 +0000 (15:25 -0800)]
net: remove __napi_complete()
All __napi_complete() callers have been converted to
use the more standard napi_complete_done(),
we can now remove this NAPI method for good.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 4 Feb 2017 23:25:01 +0000 (15:25 -0800)]
aeroflex/greth: use napi_complete_done()
We plan to remove __napi_complete() soon,
this driver is the last user.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 4 Feb 2017 23:25:00 +0000 (15:25 -0800)]
ibm/emac: use napi_complete_done()
Use napi_complete_done() instead of __napi_complete()
We plan to remove __napi_complete() to reduce NAPI complexity.
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 4 Feb 2017 23:24:59 +0000 (15:24 -0800)]
qla3xxx: add GRO support
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 4 Feb 2017 23:24:58 +0000 (15:24 -0800)]
ks8695net: add GRO support
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
Note that rx_lock seems to be useless, NAPI logic should
not need this extra care.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 4 Feb 2017 23:24:57 +0000 (15:24 -0800)]
skge: use napi_complete_done()
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API and get rid of napi_gro_flush()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 4 Feb 2017 23:24:56 +0000 (15:24 -0800)]
ep93xx_eth: add GRO support
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
4) get rid of baroque code and ease maintenance.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 4 Feb 2017 23:24:55 +0000 (15:24 -0800)]
pcnet32: use napi_complete_done()
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 4 Feb 2017 23:24:54 +0000 (15:24 -0800)]
amd8111e: add GRO support
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
4) get rid of baroque code and ease maintenance.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 4 Feb 2017 23:24:53 +0000 (15:24 -0800)]
epic100: use napi_complete_done()
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
4) get rid of baroque code and ease maintenance.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 4 Feb 2017 23:24:52 +0000 (15:24 -0800)]
8139cp: use napi_complete_done()
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
4) Eventually get rid of napi_gro_flush() in the future.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 4 Feb 2017 23:24:51 +0000 (15:24 -0800)]
8139too: use napi_complete_done()
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 5 Feb 2017 00:58:15 +0000 (19:58 -0500)]
Merge branch 'ipv6-Improve-user-experience-with-multipath-routes'
David Ahern says:
====================
net: ipv6: Improve user experience with multipath routes
This series closes a couple of gaps between IPv4 and IPv6 with respect
to multipath routes:
1. IPv4 allows all nexthops of multipath routes to be deleted using just
the prefix and length; IPv6 only deletes the first nexthop for the
route if only the prefix and length are given.
2. IPv4 returns multipath routes encoded in the RTA_MULTIPATH attribute.
IPv6 returns a series of routes with the same prefix and length - one
for each nexthop. This happens for both dumps and notifications.
IPv6 does accept RTA_MULTIPATH encoded routes, but installs them as a
series of routes.
Patch 1 addresses the first item by allowing IPv6 multipath routes to be
deleted using just the prefix and length. Patch 2 addresses the second
allowing IPv6 multipath routes to be returned encoded in the RTA_MULTIPATH.
Patches 3 and 4 upate the RTM_{NEW,DEL}ROUTE notifications to generate
1 notification with RTA_MULTIPATH where applicable.
Patch 5 prints IPv6 addresses in compressed format when showing route
replace errors. This was noticed testing REPLACE failures.
The end result for multipath routes:
1. Dump
- RTA_MULTIPATH used for multipath routes
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:200::/120 metric 1024
nexthop via 2001:db8:1::2 dev eth1 weight 1
nexthop via 2001:db8:2::2 dev eth2 weight 1
...
2. Route Add
- one notification with RTA_MULTIPATH attribute
$ ip -6 ro add vrf red 2001:db8:200::/120 nexthop via 2001:db8:1::2 nexthop via 2001:db8:2::2
$ ip mon route
2001:db8:200::/120 table red metric 1024
nexthop via 2001:db8:1::2 dev eth1 weight 1
nexthop via 2001:db8:2::2 dev eth2 weight 1
2. Route Replace
- one notification with RTA_MULTIPATH attribute
$ ip -6 ro replace vrf red 2001:db8:200::/120 nexthop via 2001:db8:1::16 nexthop via 2001:db8:2::16
$ ip mon route
Replaced 2001:db8:200::/120 table red metric 1024
nexthop via 2001:db8:1::16 dev eth1 weight 1
nexthop via 2001:db8:2::16 dev eth2 weight 1
- on a failure after the insertion of the first nexthop (which means
the original route has been replaced in the FIB), a notification is
sent with the successful nexthops and then the nexthops are deleted
with one notification per hop. This is consistent with how it works
today except the successful additions are coalesced into 1
notification.
3. Route Delete
- delete of entire multipath route using prefix/length only 1
notification is generated:
$ ip -6 ro del vrf red 2001:db8:200::/120
$ ip mon route
Deleted 2001:db8:200::/120 table red metric 1024
nexthop via 2001:db8:1::16 dev eth1 weight 1
nexthop via 2001:db8:2::16 dev eth2 weight 1
- if a delete request contains nexthops one notification is
generated per nexthop deleted. This is unavoidable since IPv6
alllows a single nexthop to be deleted within a multipath route
4. Route Appends
- IPv6 allows nexthops to be appended to an existing route. In this
case one notification is sent for the new route with the append
flag set.
$ ip -6 ro append vrf red 2001:db8:200::/120 nexthop via 2001:db8:2::20 nexthop via 2001:db8:1::20
$ ip mon route
Append 2001:db8:200::/120 table red metric 1024
nexthop via 2001:db8:1::2 dev eth1 weight 1
nexthop via 2001:db8:2::2 dev eth2 weight 1
nexthop via 2001:db8:2::20 dev eth2 weight 1
nexthop via 2001:db8:1::20 dev eth1 weight 1
- on failure of an append, a notification is sent with the route
containing all of the nexthops successfully added, and it is
followed by delete notifications as the hops are removed
returning the route to its prior state. This is consistent with
how it works today except the successful additions are coalesced
into 1 notification.
Addresses some of the inconsistencies also noted by Roopa at netdev0.1:
https://www.netdev01.org/docs/prabhu-linux_ipv4_ipv6_inconsistencies_talk_slides.pdf
v4
- changed series to do encoding in 1 patch and updating notificatons
in separate patches to make it easier to review and understand
- 1 notification for delete when using prefix/length; 1 notification for
append
- handle delete of a single nexthop without RTA_MULTIPATH in delete request
- upated commit messages and cover letter
v3
- removed the need for a user API to opt-in to change. Requiring an
API just shifts the difference from same API with different
behavior to different API to achieve equivalent behavior
- route notifications changed to use RTA_MULTIPATH for add and replace
- upated commit messages and cover letter
v2
- fixed locking in patch 1 as noted by DaveM
- changed user API for patch 2 to require an rtmsg with RTM_F_ALL_NEXTHOPS
set in rtm_flags
- revamped explanation of patch 2 and cover letter
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 2 Feb 2017 20:37:12 +0000 (12:37 -0800)]
net: ipv6: Use compressed IPv6 addresses showing route replace error
ip6_print_replace_route_err logs an error if a route replace fails with
IPv6 addresses in the full format. e.g,:
IPv6: IPV6: multipath route replace failed (check consistency of installed routes): 2001:0db8:0200:0000:0000:0000:0000:0000 nexthop 2001:0db8:0001:0000:0000:0000:0000:0016 ifi 0
Change the message to dump the addresses in the compressed format.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 2 Feb 2017 20:37:11 +0000 (12:37 -0800)]
net: ipv6: Change notifications for multipath delete to RTA_MULTIPATH
If an entire multipath route is deleted using prefix and len (without any
nexthops), send a single RTM_DELROUTE notification with the full route
using RTA_MULTIPATH. This is done by generating the skb before the route
delete when all of the sibling routes are still present but sending it
after the route has been removed from the FIB. The skip_notify flag
is used to tell the lower fib code not to send notifications for the
individual nexthop routes.
If a route is deleted using RTA_MULTIPATH for any nexthops or a single
nexthop entry is deleted, then the nexthops are deleted one at a time with
notifications sent as each hop is deleted. This is necessary given that
IPv6 allows individual hops within a route to be deleted.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 2 Feb 2017 20:37:10 +0000 (12:37 -0800)]
net: ipv6: Change notifications for multipath add to RTA_MULTIPATH
Change ip6_route_multipath_add to send one notifciation with the full
route encoded with RTA_MULTIPATH instead of a series of individual routes.
This is done by adding a skip_notify flag to the nl_info struct. The
flag is used to skip sending of the notification in the fib code that
actually inserts the route. Once the full route has been added, a
notification is generated with all nexthops.
ip6_route_multipath_add handles 3 use cases: new routes, route replace,
and route append. The multipath notification generated needs to be
consistent with the order of the nexthops and it should be consistent
with the order in a FIB dump which means the route with the first nexthop
needs to be used as the route reference. For the first 2 cases (new and
replace), a reference to the route used to send the notification is
obtained by saving the first route added. For the append case, the last
route added is used to loop back to its first sibling route which is
the first nexthop in the multipath route.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 2 Feb 2017 20:37:09 +0000 (12:37 -0800)]
net: ipv6: Add support to dump multipath routes via RTA_MULTIPATH attribute
IPv6 returns multipath routes as a series of individual routes making
their display and handling by userspace different and more complicated
than IPv4, putting the burden on the user to see that a route is part of
a multipath route and internally creating a multipath route if desired
(e.g., libnl does this as of commit
29b71371e764). This patch addresses
this difference, allowing multipath routes to be returned using the
RTA_MULTIPATH attribute.
The end result is that IPv6 multipath routes can be treated and displayed
in a format similar to IPv4:
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:200::/120 metric 1024
nexthop via 2001:db8:1::2 dev eth1 weight 1
nexthop via 2001:db8:2::2 dev eth2 weight 1
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 2 Feb 2017 20:37:08 +0000 (12:37 -0800)]
net: ipv6: Allow shorthand delete of all nexthops in multipath route
IPv4 allows multipath routes to be deleted using just the prefix and
length. For example:
$ ip ro ls vrf red
unreachable default metric 8192
1.1.1.0/24
nexthop via 10.100.1.254 dev eth1 weight 1
nexthop via 10.11.200.2 dev eth11.200 weight 1
10.11.200.0/24 dev eth11.200 proto kernel scope link src 10.11.200.3
10.100.1.0/24 dev eth1 proto kernel scope link src 10.100.1.3
$ ip ro del 1.1.1.0/24 vrf red
$ ip ro ls vrf red
unreachable default metric 8192
10.11.200.0/24 dev eth11.200 proto kernel scope link src 10.11.200.3
10.100.1.0/24 dev eth1 proto kernel scope link src 10.100.1.3
The same notation does not work with IPv6 because of how multipath routes
are implemented for IPv6. For IPv6 only the first nexthop of a multipath
route is deleted if the request contains only a prefix and length. This
leads to unnecessary complexity in userspace dealing with IPv6 multipath
routes.
This patch allows all nexthops to be deleted without specifying each one
in the delete request. Internally, this is done by walking the sibling
list of the route matching the specifications given (prefix, length,
metric, protocol, etc).
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:200::/120 via 2001:db8:1::2 dev eth1 metric 1024 pref medium
2001:db8:200::/120 via 2001:db8:2::2 dev eth2 metric 1024 pref medium
...
$ ip -6 ro del vrf red 2001:db8:200::/120
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
...
Because IPv6 allows individual nexthops to be deleted without deleting
the entire route, the ip6_route_multipath_del and non-multipath code
path (ip6_route_del) have to be discriminated so that all nexthops are
only deleted for the latter case. This is done by making the existing
fc_type in fib6_config a u16 and then adding a new u16 field with
fc_delete_all_nh as the first bit.
Suggested-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>