John Crispin [Tue, 24 Nov 2015 22:00:55 +0000 (22:00 +0000)]
ralink: renable nand support
CONFIG_MTK_MTD_NAND was incorrectly disabled by r47619.
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 47640
Jo-Philipp Wich [Tue, 24 Nov 2015 21:16:38 +0000 (21:16 +0000)]
base-files: config_generate: support autogenerating vlans
Add support for generating vlans solely from the port layout description
given through ucidef_add_switch_ports().
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47639
Jo-Philipp Wich [Tue, 24 Nov 2015 21:16:35 +0000 (21:16 +0000)]
base-files: add ucidef_set_interface_wan() and ucidef_add_switch_ports()
Add further helper functions to uci-defaults-new.sh for easier declarations
of complex switch layouts.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47638
John Crispin [Tue, 24 Nov 2015 20:41:30 +0000 (20:41 +0000)]
lantiq: ltq-vdsl-app: update to version 4.16.6.3
In this upstream dsl driver app version the autoboot is deactivated activate
it again.
In addition to the update this also fixes some build warnings and makes it
use the same configure option as used in Lantiq UGW.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
SVN-Revision: 47637
John Crispin [Tue, 24 Nov 2015 20:41:18 +0000 (20:41 +0000)]
lantiq: ltq-vdsl-app: add dsl_cpe_pipe.sh
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
SVN-Revision: 47636
John Crispin [Tue, 24 Nov 2015 20:41:07 +0000 (20:41 +0000)]
lantiq: ltq-vdsl: update to version 4.16.6.3
In addition to the update this also fixes some build warnings and makes it
use the same configure option as used in Lantiq UGW.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
SVN-Revision: 47635
John Crispin [Tue, 24 Nov 2015 20:40:59 +0000 (20:40 +0000)]
lantiq: ltq-vdsl-mei: update to version 1.4.8.5
In addition to the update this also fixes some build warnings and makes it
use the same configure option as used in Lantiq UGW.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
SVN-Revision: 47634
John Crispin [Tue, 24 Nov 2015 20:40:49 +0000 (20:40 +0000)]
lantiq: ltq-vdsl-mei: register char device automatically
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
SVN-Revision: 47633
John Crispin [Tue, 24 Nov 2015 20:40:40 +0000 (20:40 +0000)]
lantiq: ltq-vdsl-mei: add mei_cpe_drv_test application
This application helps to debug some internal problems in the MEI driver.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
SVN-Revision: 47632
John Crispin [Tue, 24 Nov 2015 20:40:11 +0000 (20:40 +0000)]
lantiq: add dsl-vr9-firmware-xdsl
This adds the DSL firmware for the VR9/XRX200 SoCs.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
SVN-Revision: 47631
John Crispin [Tue, 24 Nov 2015 20:39:59 +0000 (20:39 +0000)]
lantiq: ltq-ifxos: fix build warnings
This makes the build script use the same configure options as used by
Lantiq UGW and fixes some warnings and cleans up some of the patches.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@lantiq.com>
SVN-Revision: 47630
Felix Fietkau [Tue, 24 Nov 2015 20:30:06 +0000 (20:30 +0000)]
qos-scripts: remove faulty fallback of the device variable to eth0 (#20834)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47629
Hauke Mehrtens [Tue, 24 Nov 2015 20:12:21 +0000 (20:12 +0000)]
lantiq: fix compile error
This fixes a problem introduced in r47624.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47628
Felix Fietkau [Tue, 24 Nov 2015 19:29:56 +0000 (19:29 +0000)]
ramips: fix typo in image makefile (#18712)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47627
Felix Fietkau [Tue, 24 Nov 2015 19:09:56 +0000 (19:09 +0000)]
kernel: disable software protection bits for macronix flash chips at init
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47626
Felix Fietkau [Tue, 24 Nov 2015 19:09:45 +0000 (19:09 +0000)]
ath10k: fix memory allocation issues on platforms where DMA coherent memory is constrained
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47625
Felix Fietkau [Tue, 24 Nov 2015 18:59:28 +0000 (18:59 +0000)]
kernel: update m25p80 in 4.1 to the latest version from 4.4-rc1
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47624
John Crispin [Tue, 24 Nov 2015 18:32:09 +0000 (18:32 +0000)]
base-files: show hint when JFFS2-partition is full and overlayfs mounted read-only
since r45833 and r45848 the overlayfs is automatically mounted read-only
(and blocks remounts as r/w) when JFFS2 is full. see ticket #19564
because of this normal file deletion is not possible anymore.
if a user logins interactively (e.g. SSH) show a hint for this,
that files must be removed in /overlay/upper/...
v2: fix subject line
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 47623
John Crispin [Tue, 24 Nov 2015 18:30:50 +0000 (18:30 +0000)]
ar71xx: add GL-Domino Pi support V3
This is the patch for GL-Domino Pi V3. Updated against the latest trunk.
Signed-off-by: alzhao<alzhao@gmail.com>
SVN-Revision: 47622
John Crispin [Tue, 24 Nov 2015 18:30:19 +0000 (18:30 +0000)]
ar71xx: add GL-AR300 support V3
This is the patch for GL-AR300 V3, tested against the latest trunk.
Signed-off-by: alzhao<alzhao@gmail.com>
SVN-Revision: 47621
John Crispin [Tue, 24 Nov 2015 18:29:59 +0000 (18:29 +0000)]
ar71xx: add GL-AR150 support V3
This is the 3rd version. Modified against the latest trunk.
Signed-off-by: alzhao<alzhao@gmail.com>
SVN-Revision: 47620
John Crispin [Tue, 24 Nov 2015 18:29:26 +0000 (18:29 +0000)]
ralink: add support for netis WF-2881
netis WF-2881 is an MT7621AT based router with MT7602EN, MT7612EN.
It has 128MB DDR3, 128MB SLC NAND FLASH, 5-port Gbps switch and 1x USB 3.0.
The following patch adds support for this device.
this device only works on top of UBI.
Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons (reset button)
* ethernet switch and USB diag LEDs
* UART
* GPIOs
* sysupgrade
Tested and not working
* failsafe
Signed-off-by: YounJae Rho <luxflow@live.com>
SVN-Revision: 47619
John Crispin [Tue, 24 Nov 2015 18:29:14 +0000 (18:29 +0000)]
oxnas: set irq of usb&sata to cpu1
V2:
The KD-20 also has USB 3.0.I modiy the set_irq_affinity usb 2 to set_irq_affinity ?hci_hcd 2 to bind usb 2.0&3.0 to cpu1.
Signed-off-by: Shonn Lu <countrysideboy@qq.com>
SVN-Revision: 47618
John Crispin [Tue, 24 Nov 2015 18:29:02 +0000 (18:29 +0000)]
ramips: add support for Youku YK1
Changes since V1:
I resend this patch for current trunk.The former V1 patch is for CC branch.
Signed-off-by: Shonn Lu <countrysideboy@qq.com>
SVN-Revision: 47617
John Crispin [Tue, 24 Nov 2015 18:28:54 +0000 (18:28 +0000)]
ramips: add second spi master sysclk
for mt7620, rt3883 and rt5350
Signed-off-by: Michael Lee <igvtee@gmail.com>
SVN-Revision: 47616
John Crispin [Tue, 24 Nov 2015 18:28:44 +0000 (18:28 +0000)]
wpa-supplicant: Get 802.11s ssid information from option mesh_id
The scripts for authsae and iw use the option mesh_id to get set the
"meshid" during a mesh join. But the script for wpad-mesh ignores the
option mesh_id and instead uses the option ssid. Unify the mesh
configuration and let the wpa_supplicant script also use the mesh_id from
the configuration.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47615
John Crispin [Tue, 24 Nov 2015 18:28:35 +0000 (18:28 +0000)]
authsae: Use kbit/s as mcast_rate unit like wpad
The OpenWrt wireless configuration for mcast_rate is defined as Kbit/s when
using wpa_supplicant for IBSS/802.11s and iw for unencrypted IBSS/802.11s.
But when using authsae, the unit for the same option is redefined as
Mbit/s. Better use the same unit for this option independent of the backend
which is used.
Old values for mcast_rate (< 1000) are still interpreted Mbit/s to avoid
problems during upgrades from older versions.
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47614
John Crispin [Tue, 24 Nov 2015 18:28:19 +0000 (18:28 +0000)]
authsae: Fix meshid in authsae config
The variable $mesh_id was never defined in authsae_start_interface and thus
the option meshid in $authsae_conf_file was always set to "".
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
SVN-Revision: 47613
John Crispin [Tue, 24 Nov 2015 18:28:05 +0000 (18:28 +0000)]
ar71xx: Build initramfs by default for Mikrotik devices
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
SVN-Revision: 47612
John Crispin [Tue, 24 Nov 2015 18:27:57 +0000 (18:27 +0000)]
uboot-imx6: fix build with gcc-5
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 47611
John Crispin [Tue, 24 Nov 2015 18:27:43 +0000 (18:27 +0000)]
brcm2708: fix multi-device image generation
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 47610
Jo-Philipp Wich [Tue, 24 Nov 2015 13:39:53 +0000 (13:39 +0000)]
base-files: config_generate: honour port_mask property (#20963)
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47609
Felix Fietkau [Sun, 22 Nov 2015 21:59:22 +0000 (21:59 +0000)]
ipq806x: another fix to the stmmac DMA configuration to fix remaining data corruption issues
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47603
Hauke Mehrtens [Sun, 22 Nov 2015 21:21:09 +0000 (21:21 +0000)]
ubox: update ubox to version 2015-11-22
This version fixes a potential uncontrolled format string problem. This
makes it possible to activate the format security check.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47600
Hauke Mehrtens [Sun, 22 Nov 2015 21:20:45 +0000 (21:20 +0000)]
mountd: update mountd to version 2015-11-22
This version fixes a potential uncontrolled format string problem. This
makes it possible to activate the format security check.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47599
Hauke Mehrtens [Sun, 22 Nov 2015 21:20:02 +0000 (21:20 +0000)]
fstools: update fstools to version 2015-11-22
This version fixes a potential uncontrolled format string problem. This
makes it possible to activate the format security check.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47598
Jo-Philipp Wich [Sun, 22 Nov 2015 20:52:10 +0000 (20:52 +0000)]
Revert "mvebu: migrate led and network setup to board detection framework"
Roll back the mvebu conversion to board detection code as we need to fix
some strcutural issues first.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47597
Jo-Philipp Wich [Sun, 22 Nov 2015 20:00:13 +0000 (20:00 +0000)]
ar71xx: fix network default config of the TEW-732BR
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47595
Felix Fietkau [Sun, 22 Nov 2015 19:07:00 +0000 (19:07 +0000)]
ipq806x: fix a nasty stmmac data corruption bug caused by faulty DMA initialization
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47594
Felix Fietkau [Sun, 22 Nov 2015 19:06:51 +0000 (19:06 +0000)]
ipq806x: update stmmac to the version from linux 4.3
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47593
Felix Fietkau [Sun, 22 Nov 2015 19:06:42 +0000 (19:06 +0000)]
ath10k-firmware: add board-2.bin for qca99x0
Keep board.bin as fallback for devices without OTP that load caldata
from flash
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47592
Felix Fietkau [Sun, 22 Nov 2015 19:06:33 +0000 (19:06 +0000)]
build: add support for choosing a different url filename part than the output file
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47591
Felix Fietkau [Sun, 22 Nov 2015 19:06:20 +0000 (19:06 +0000)]
base-files: use the correct path in case of modified preinit options
If the user sets any preinit options in .config, the wrong path may get
applied due to wrong default value in image-config.in and due to Makefile
writing also the unchanged options into 00_preinit.conf
Modify the default path in image-config.in to match the current default
path set by r47080. Also modify the fall-back default in Makefile.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 47590
Felix Fietkau [Sun, 22 Nov 2015 19:06:07 +0000 (19:06 +0000)]
linux: add support of Synopsys ARC770-based boards
This patch introduces support of new boards with ARC cores.
[1] Synopsys SDP board
This is a new-generation development board from Synopsys that
consists of base-board and CPU tile-board (which might have a real
ASIC or FPGA with CPU image).
It sports a lot of DesignWare peripherals like GMAC, USB, SPI, I2C
etc and is intended to be used for early development of ARC-based
products.
[2] nSIM
This is a virtual board implemented in Synopsys proprietary
software simulator (even though available for free for open source
community). This board has only serial port as a peripheral and so
it is meant to be used for runtime testing which is especially
useful during bring-up of new tools and platforms.
What's also important ARC cores are very configurable so there're
many variations of options like cache sizes, their line lengths,
additional hardware blocks like multipliers, dividers etc. And this
board could be used to make sure built software still runs on
different HW configurations.
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Jo-Philipp Wich <jow@openwrt.org>
Cc: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
SVN-Revision: 47589
Felix Fietkau [Sun, 22 Nov 2015 19:05:53 +0000 (19:05 +0000)]
kernel: mtd: Backport GD25Q128B support to 3.18
Support is present in 3.19 and above as kernel commit:
fcc87a95195236b0935183361a72e4a98bf577d8
Changes to other existing patches are a result of "make target/linux/refresh".
Signed-off-by: Srdjan Rosic <srdjan.rosic@gmail.com>
Signed-off-by: Srdjan Rosic <rosic@google.com>
SVN-Revision: 47588
Hauke Mehrtens [Sun, 22 Nov 2015 14:56:17 +0000 (14:56 +0000)]
usign: Revert r47582 "usign: activate format-security checks"
I accidentally deactivated it. This should be set to active it in any case
independently what was set in the user config.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47587
Hauke Mehrtens [Sun, 22 Nov 2015 14:18:40 +0000 (14:18 +0000)]
iperf: activate format-security checks
This patch was taken from debian.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47586
Hauke Mehrtens [Sun, 22 Nov 2015 14:18:04 +0000 (14:18 +0000)]
gettext-full: activate format-security checks
This patch was taken from upstream libcroco
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47585
Hauke Mehrtens [Sun, 22 Nov 2015 14:17:11 +0000 (14:17 +0000)]
gettext-full: update to version 0.19.6
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47584
Hauke Mehrtens [Sun, 22 Nov 2015 14:16:09 +0000 (14:16 +0000)]
px5g-standalone: activate format-security checks
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47583
Hauke Mehrtens [Sun, 22 Nov 2015 14:15:34 +0000 (14:15 +0000)]
usign: activate format-security checks
This still compiles with format-security checks activated.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47582
Hauke Mehrtens [Sun, 22 Nov 2015 14:13:47 +0000 (14:13 +0000)]
xfsprogs: activate format-security checks
This patch was taken from upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47581
John Crispin [Sun, 22 Nov 2015 11:49:13 +0000 (11:49 +0000)]
ramips: update dtsi files to support second spi device
Signed-off-by: Michael Lee <igvtee@gmail.com>
SVN-Revision: 47580
John Crispin [Sun, 22 Nov 2015 11:49:04 +0000 (11:49 +0000)]
ramips: use transfer_one instead of transfer_one_message on rt2880 spi
* use kernel buildin transfer_one_message. we only need to implement
transfer_one and set_cs function
* should support use gpio as cs pin
* deselected the spi device when setup and add debug info
* only reset device when first driver probe
Signed-off-by: Michael Lee <igvtee@gmail.com>
SVN-Revision: 47579
John Crispin [Sun, 22 Nov 2015 11:48:57 +0000 (11:48 +0000)]
ramips: move rt2880 spi clock and reset init code to spi_prepare_message
before spi transfer. use spi_prepare_message to setup spi hardware. it
will setup MSB, spi mode and speed
remove sys_freq member and speed check code
Signed-off-by: Michael Lee <igvtee@gmail.com>
SVN-Revision: 47578
John Crispin [Sun, 22 Nov 2015 11:48:51 +0000 (11:48 +0000)]
ramips: improve rt2880 spi setup
* check clock rate, SPI mode, and word sizes
* setup spi polarity
* enable spi1 hw if need
Signed-off-by: Michael Lee <igvtee@gmail.com>
SVN-Revision: 47577
John Crispin [Sun, 22 Nov 2015 11:48:45 +0000 (11:48 +0000)]
ramips: clean up rt2880 spi probe/remove
* fill struct according to the member order
* add error clean up
* set min/max spi speed. so we don't need to check again
Signed-off-by: Michael Lee <igvtee@gmail.com>
SVN-Revision: 47576
John Crispin [Sun, 22 Nov 2015 11:48:34 +0000 (11:48 +0000)]
ramips: improve rt2880 spi wait ready function
use loops_per_jiffy, spi clock speed and write bytes to get the
spi loop count. if loop to 0 than spi operation timeout.
remove usleep. we only write 1 byte to spi device. use busy loop
would be better.
Signed-off-by: Michael Lee <igvtee@gmail.com>
SVN-Revision: 47575
John Crispin [Sun, 22 Nov 2015 11:48:21 +0000 (11:48 +0000)]
ramips: remove rt2880 spi lock and clean bit operation
Signed-off-by: Michael Lee <igvtee@gmail.com>
SVN-Revision: 47574
John Crispin [Sun, 22 Nov 2015 11:48:10 +0000 (11:48 +0000)]
ramips: add rt2880/mt7620 spi register defines
Signed-off-by: Michael Lee <igvtee@gmail.com>
SVN-Revision: 47573
John Crispin [Sun, 22 Nov 2015 08:04:37 +0000 (08:04 +0000)]
brcm2708: add device detection and use it for network, leds and preinit
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 47572
John Crispin [Sat, 21 Nov 2015 21:26:20 +0000 (21:26 +0000)]
conntrack-tools: create /etc/conntrackd directory
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
SVN-Revision: 47571
John Crispin [Sat, 21 Nov 2015 21:26:12 +0000 (21:26 +0000)]
conntrack-tools: use INSTALL_DIR once
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
SVN-Revision: 47570
John Crispin [Sat, 21 Nov 2015 21:26:06 +0000 (21:26 +0000)]
tools/scons: update to 2.4.1
Update scons to 2.4.1.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 47569
John Crispin [Sat, 21 Nov 2015 21:26:02 +0000 (21:26 +0000)]
tools/cmake: update to 3.4.0
Update cmake to 3.4.0.
Refresh patches.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
SVN-Revision: 47568
John Crispin [Sat, 21 Nov 2015 21:25:54 +0000 (21:25 +0000)]
kernel/generic: 3.18, 4.y: Add support for Quectel EC20 Mini PCIe module
* both patches (qcserial/qmi_wwan) were submitted upstream[1,2]
* build tested on 3.18 and 4.1
* run tested on imx6 platform with 4.1
1. http://article.gmane.org/gmane.linux.usb.general/132998
2. http://article.gmane.org/gmane.linux.usb.general/133113
Signed-off-by: Petr Štetiar <ynezz@true.cz>
SVN-Revision: 47567
John Crispin [Sat, 21 Nov 2015 21:25:43 +0000 (21:25 +0000)]
lantiq: add phy led config support over devicetree bindings
This patch adds the posibility to config the led behaviour of the lantiq phys
over the devicetree bindings.It patches the 0023-NET-PHY-adds-driver-for-lantiq-PHY11G
for 3.18 and 4.1. I have also added a register description overview for
applicable values. This goes to the documentation folder in the linux kernel.
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
SVN-Revision: 47566
John Crispin [Sat, 21 Nov 2015 21:25:33 +0000 (21:25 +0000)]
ralink: add missing nand layer hack
It turned out that mtk_nand driver uses some sophisticated accounting and a
general nand code must be patched.
This patch adds required read and erase calls to a general nand code. I
used a code for re6500 released by Linksys as a reference.
All required operations (erase, write and read) are usable. However I found
that jffs2 filesystem can be created only on top of a ubi volume. I tried
to create jffs2 directly on mtd device but pages with clean markers are
became uncorrectable.
Signed-off-by: Kirill Berezin <fyiwdt@gmail.com>
SVN-Revision: 47565
John Crispin [Sat, 21 Nov 2015 21:25:28 +0000 (21:25 +0000)]
kernel: fix building RTC drivers
All RTC drivers require the kernel to be built with CONFIG_RTC_CLASS=y.
Set it accordingly.
Tested only with DS1307.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
SVN-Revision: 47564
John Crispin [Sat, 21 Nov 2015 21:25:20 +0000 (21:25 +0000)]
lantiq: tweak DWC2 default parameters
This patch improves the default configuration of DWC2 on lantiq SoCs
somewhat:
* Set maximum packet count to largest allowed value by the DWC2 (511)
* Use 16-bit DMA bursts
* Divide fifo buffers more evenly
Default fifo buffer sizes from original ltq-hcd driver seem really
irrational. For example according to DWC2 data book rxfifo size of 240
will not fit even a single full length USB packet. On the other hand
non-periodic tx fifo size of 240 is more than enough to fit one complete
packet.
Change the sizes around to improve the situation and to fix some issues
especially with isochronous USB transfers.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
SVN-Revision: 47563
John Crispin [Sat, 21 Nov 2015 21:25:13 +0000 (21:25 +0000)]
brcm2708: enable hard float ABI
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 47562
John Crispin [Sat, 21 Nov 2015 21:25:04 +0000 (21:25 +0000)]
brcm2708: add support for multi-device images
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 47561
John Crispin [Sat, 21 Nov 2015 21:24:57 +0000 (21:24 +0000)]
brcm2708: rename image device definition
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 47560
John Crispin [Sat, 21 Nov 2015 21:24:50 +0000 (21:24 +0000)]
brcm2708: revert sd image extension to .img
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 47559
John Crispin [Sat, 21 Nov 2015 21:24:44 +0000 (21:24 +0000)]
brcm2708: simplify gzip image generation
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 47558
John Crispin [Sat, 21 Nov 2015 21:24:38 +0000 (21:24 +0000)]
ramips: init usb power for Lenovo Y1S
Signed-off-by: Shonn Lu <countrysideboy@qq.com>
SVN-Revision: 47557
John Crispin [Sat, 21 Nov 2015 21:24:28 +0000 (21:24 +0000)]
mac80211: fix autoprobing of mt7601u driver
Strigng passed to autoprobing script should match
module's name. Currently that string is missing trailing "u".
With that change mt7601u driver really gets autoloaded on
USB Wi-Fi dongle insertion:
------------------>8---------------
[ 0.930000] hub 2-0:1.0: USB hub found
[ 0.940000] hub 2-0:1.0: 1 port detected
[ 1.150000] usb 1-1: new high-speed USB device number 2 using
ehci-platform
[ 1.720000] init: - preinit -
Detected arc-sdp // Synopsys AXS101 Development Board
[ 1.810000] random: mktemp urandom read with 3 bits of entropy
available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug
level
[ 4.940000] procd: - early -
[ 5.540000] procd: - ubus -
[ 6.550000] procd: - init -
Please press Enter to activate this console.
[ 7.160000] Loading modules backported from Linux version
master-2015-10-26-0-g28c26cb
[ 7.170000] Backport generated by backports.git
backports-20150903-4-g12cf266
[ 7.200000] cfg80211: World regulatory domain updated:
[ 7.230000] cfg80211: DFS Master region: unset
[ 7.230000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp), (dfs_cac_time)
[ 7.250000] cfg80211: (
2402000 KHz -
2472000 KHz @ 40000 KHz),
(N/A, 2000 mBm), (N/A)
[ 7.270000] cfg80211: (
2457000 KHz -
2482000 KHz @ 40000 KHz),
(N/A, 2000 mBm), (N/A)
[ 7.270000] cfg80211: (
2474000 KHz -
2494000 KHz @ 20000 KHz),
(N/A, 2000 mBm), (N/A)
[ 7.290000] cfg80211: (
5170000 KHz -
5250000 KHz @ 80000 KHz,
160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 7.290000] cfg80211: (
5250000 KHz -
5330000 KHz @ 80000 KHz,
160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 7.310000] cfg80211: (
5490000 KHz -
5730000 KHz @ 160000 KHz),
(N/A, 2000 mBm), (0 s)
[ 7.310000] cfg80211: (
5735000 KHz -
5835000 KHz @ 80000 KHz),
(N/A, 2000 mBm), (N/A)
[ 7.330000] cfg80211: (
57240000 KHz -
63720000 KHz @
2160000 KHz),
(N/A, 0 mBm), (N/A)
[ 7.470000] usb 1-1: reset high-speed USB device number 2 using
ehci-platform
[ 7.620000] mt7601u 1-1:1.0: ASIC revision:
76010001 MAC revision:
76010500
[ 7.630000] mt7601u 1-1:1.0: Firmware Version: 0.1.00 Build: 7640
Build time: 201302052146____
[ 8.040000] mt7601u 1-1:1.0: Warning: unsupported EEPROM version 0d
[ 8.050000] mt7601u 1-1:1.0: EEPROM ver:0d fae:00
[ 8.050000] mt7601u 1-1:1.0: EEPROM country region 01 (channels 1-13)
[ 8.320000] usbcore: registered new interface driver mt7601u
------------------>8---------------
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Dirk Neukirchen <dirkneukirchen@web.de>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: John Crispin <blogic@openwrt.org>
SVN-Revision: 47556
John Crispin [Sat, 21 Nov 2015 21:24:23 +0000 (21:24 +0000)]
ar71xx: fix the SingleProfile kernel size limit for dLAN devices
it ends up as $(2) of CatFiles and must be a plain decimal value.
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
SVN-Revision: 47555
John Crispin [Sat, 21 Nov 2015 21:24:18 +0000 (21:24 +0000)]
ar71xx: add support for the devolo dLAN Hotspot
Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de>
SVN-Revision: 47554
John Crispin [Sat, 21 Nov 2015 21:24:11 +0000 (21:24 +0000)]
ar71xx: fix AR71XX_MODEL on TP-Link TL-WR703N
The hwid check was wrong, causing the AR71XX_MODEL value to end with a
space (as $hwver was unset).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47553
John Crispin [Sat, 21 Nov 2015 21:24:03 +0000 (21:24 +0000)]
oxnas: add missing platform bindings for stmmac glue
r47218 was missing needed changes which were accidentally
ommitted from the patch.
This should fix #20878
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 47552
Hauke Mehrtens [Sat, 21 Nov 2015 17:40:46 +0000 (17:40 +0000)]
kernel: make kmod-usb-dwc2 depend on kmod-usb-gadget on omap target
This dependency is missing for the omap target.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47551
Hauke Mehrtens [Sat, 21 Nov 2015 17:36:31 +0000 (17:36 +0000)]
kernel: fix build of kmod-dwc2
dwc2_platform.koi is included in dwc2.ko with kernel 4.3.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47550
Hauke Mehrtens [Sat, 21 Nov 2015 17:35:59 +0000 (17:35 +0000)]
kernel: add missing config option
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47549
Felix Fietkau [Sat, 21 Nov 2015 10:55:36 +0000 (10:55 +0000)]
ath10k: select kernel relayfs support
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47548
Felix Fietkau [Sat, 21 Nov 2015 10:55:29 +0000 (10:55 +0000)]
ipq806x: fix PCIe reset gpio handling - the core already handles the active-low flag
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47547
Felix Fietkau [Sat, 21 Nov 2015 10:55:17 +0000 (10:55 +0000)]
ipq806x: assert AHB PCIe reset during init
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47546
Felix Fietkau [Sat, 21 Nov 2015 10:55:05 +0000 (10:55 +0000)]
ipq806x: reduce PCIe buffer size setting to fix potential data corruption issues
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47545
Felix Fietkau [Sat, 21 Nov 2015 10:54:58 +0000 (10:54 +0000)]
ipq806x: fix pcie reset gpio definions and move them to the common .dtsi file
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47544
Felix Fietkau [Sat, 21 Nov 2015 10:54:53 +0000 (10:54 +0000)]
ipq806x: fix pcie tx0-term-offset setting
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47543
Felix Fietkau [Sat, 21 Nov 2015 10:54:48 +0000 (10:54 +0000)]
ipq806x: fix device tree nodes for PCI to get rid of I/O and memory offsets
Fixes QCA99x0 detection issues
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47542
Jo-Philipp Wich [Fri, 20 Nov 2015 23:59:31 +0000 (23:59 +0000)]
mvebu: migrate led and network setup to board detection framework
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47541
Jo-Philipp Wich [Fri, 20 Nov 2015 23:52:31 +0000 (23:52 +0000)]
mpc85xx: migrate network setup to board detection framework
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47540
Hauke Mehrtens [Fri, 20 Nov 2015 23:38:39 +0000 (23:38 +0000)]
uboot-omap: fix build with gcc-5
This fixes some problems with gcc-5.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47539
Jo-Philipp Wich [Fri, 20 Nov 2015 23:34:11 +0000 (23:34 +0000)]
ar71xx: fix wndr3700_board_detect for some NETGEAR WNDR3700v2 (again)
When fixing the model string for WNDR3700v2 which contain a model string
followed by 0xff in r46455, the match for other versions of the WNDR3700v2
which just contain lots of 0xff broke (as the 0xff $model is checked for
is stripped off).
Fix by stripping off non-printable characters only for the actual output
string, but not for the internal matching.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 47538
Hauke Mehrtens [Fri, 20 Nov 2015 22:50:11 +0000 (22:50 +0000)]
uboot-kirkwood: fix build with gcc-5
This backports a patch from upstream u-boot to make it compile with gcc-5.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47537
Hauke Mehrtens [Fri, 20 Nov 2015 22:33:59 +0000 (22:33 +0000)]
kernel: add missing config option
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47536
Hauke Mehrtens [Fri, 20 Nov 2015 22:22:37 +0000 (22:22 +0000)]
uboot-oxnas: fix build with gcc-5
This backports a patch from upstream u-boot to make it compile with gcc-5.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47535
Jo-Philipp Wich [Fri, 20 Nov 2015 22:14:36 +0000 (22:14 +0000)]
ar71xx: migrate led and network setup to board detection framework
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47534
Hauke Mehrtens [Fri, 20 Nov 2015 21:15:48 +0000 (21:15 +0000)]
uboot-mxs: fix build with gcc-5
gcc-5 handles inline without static differently and that makes
uboot-mxs fail to build. Remove the inline so it gets exported and can
be used in other functions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47533
projects / openwrt / staging / zorun.git / log