Sean Hefty [Fri, 22 Feb 2008 18:40:45 +0000 (10:40 -0800)]
IB/cm: Flush workqueue when removing device
When a CM MAD is received, it is queued to a CM workqueue for
processing. The queued work item references the port and device on
which the MAD was received. If that device is removed from the system
before the work item can execute, the work item will reference freed
memory.
To fix this, flush the workqueue after unregistering to receive MAD,
and before the device is be freed.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Arthur Jones [Fri, 29 Feb 2008 18:13:37 +0000 (10:13 -0800)]
MAINTAINERS: update ipath owner
I'll be leaving QLogic soon for another job and Ralph has graciously
offered to take over the IPath driver maintainership.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Linus Torvalds [Fri, 29 Feb 2008 16:44:00 +0000 (08:44 -0800)]
Merge git://git./linux/kernel/git/tiwai/alsa-fix-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/alsa-fix-2.6:
[ALSA] intel8x0 - Add quirk for Compaq Deskpro EN
[ALSA] hda-codec - Adapt eeepc p701 mixer for virtual master control
[ALSA] sound: ice1712: unused structs
[ALSA] ASoC: Fix WM9712 mixer_event DAPM widget function type
[ALSA] ASoC: Fix DAPM widget function types in pxa machine drivers
[ALSA] hda-codec - Fix mixer names of realtek codecs to adapt mater controls
[ALSA] intel8x0 - Add quirk for Acer Travelmate 2310
[ALSA] hda_intel - Add model quirk for Albatron KI690-AM2 motherboard
[ALSA] oxygen: add owner field
[ALSA] hda-codec - Add Fujitsu Lifebook E8410 to quirk table
[ALSA] hda-codec - Fix AD1988 capture elements
[ALSA] sb8: fix SB 1.0 capture DMA programming
[ALSA] usb-audio: add workaround for broken E-Mu frequency feedback
[ALSA] ASoC: Fix TLV320AIC3X PLL divider table for 64 kHz rate
[ALSA] hda-codec - Fix Master volume on HP dv8000
Linus Torvalds [Fri, 29 Feb 2008 16:43:27 +0000 (08:43 -0800)]
Merge branch 'avr32-fixes' of git://git./linux/kernel/git/hskinnemoen/avr32-2.6
* 'avr32-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
avr32: Fix OCD refcounting bug
avr32: Call tick_nohz_{stop,restart}_sched_tick() in idle loop
avr32: Use correct config symbol in atstk1004 board code
avr32: Fix broken pte dump code in do_page_fault()
AVR32: Define PAGE_SHARED
Linus Torvalds [Fri, 29 Feb 2008 16:41:13 +0000 (08:41 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/cooloney/blackfin-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (35 commits)
Blackfin Serial Driver: Fix bug - Only insert UART rx char in timer task.
Blackfin Serial Driver: Fix bug - update tx dma buffer tail before wake up processes.
Blackfin Serial Driver: Fix bug - Increase buffer tail immediately before starting tx dma.
[Blackfin] serial driver: Add flow control support to bf54x
[Blackfin] serial driver: Fix bug Poll RTS/CTS status in DMA mode as well
[Blackfin] serial driver: ADSP-BF52x arch/mach support
[Blackfin] serial driver: use simpler comment headers and strip out information that is maintained in the scm's log
[Blackfin] serial driver: rework break flood anomaly handling to be more robust/realistic about what we can actually work around
[Blackfin] serial driver: fix bug - cache the bits of the LSR on systems where the LSR is read-to-clear
[Blackfin] serial driver: fix bug - should not wait for the TFI bit, just clear it when tx stop.
[Blackfin] serial driver: Fix bug serial driver in DMA mode spams history to console on shell restart
[Blackfin] serial driver: Fix bug Free rx dma buffer in shutdown.
[Blackfin] serial driver: Clean up UART DMA code.
Blackfin Serial driver: Fix bug - serial driver in PIO mode cant handle input very quickly
[Blackfin] arch: kill section mismatch warnings
[Blackfin] arch: handle the most common L1 shrinkage case (L1 does not exist for a part) so that any parts labeled for L1 instead get placed into external memory sections
[Blackfin] arch: add bfin_clear_PPIx_STATUS() helper funcs like we have for other parts
[Blackfin] arch: make sure we have proper description/copyright/license lines
[Blackfin] arch: Fix CONFIG_PM support for BF561
[Blackfin] arch: Remove DPMC char driver option
...
Linus Torvalds [Fri, 29 Feb 2008 16:40:21 +0000 (08:40 -0800)]
Merge branch 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6
* 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6:
[XFS] If you mount an XFS filesystem with no mount options at all, then
Uwe Kleine-König [Mon, 25 Feb 2008 15:45:03 +0000 (16:45 +0100)]
let __dec_zone_page_state use __dec_zone_state
This removes code duplication and makes __dec_zone_page_state look like
__inc_zone_page_state.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Acked-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 29 Feb 2008 16:32:15 +0000 (08:32 -0800)]
Merge git://git./linux/kernel/git/lethal/sh-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
arch/sh/drivers/dma/dma-sh.c: Correct use of ! and &
serial: Move asm-sh/sci.h to linux/serial_sci.h.
sh: Fix up HAS_SR_RB typo in entry-macros.
maple: fix device detection
sh: fix rtc_resources setup for sh770x
sh: heartbeat: ioremap is expected to succeed
sh: Storage class should be before const qualifier
maple: remove unused variable
sh: SH5-103 needs to select CPU_SH5.
sh: Rename SH-3 CCR3 reg to avoid synclink_cs clash.
Linus Torvalds [Fri, 29 Feb 2008 16:29:55 +0000 (08:29 -0800)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (79 commits)
[X25]: Use proc_create() to setup ->proc_fops first
[WANROUTER]: Use proc_create() to setup ->proc_fops first
[8021Q]: Use proc_create() to setup ->proc_fops first
[IPV4]: Use proc_create() to setup ->proc_fops first
[IPV6]: Use proc_create() to setup ->proc_fops first
[SCTP]: Use proc_create() to setup ->proc_fops first
[PKTGEN]: Use proc_create() to setup ->proc_fops first
[NEIGHBOUR]: Use proc_create() to setup ->proc_fops first
[LLC]: Use proc_create() to setup ->proc_fops first
[IPX]: Use proc_create() to setup ->proc_fops first
[SUNRPC]: Use proc_create() to setup ->proc_fops first
[ATM]: Use proc_create() to setup ->proc_fops first
[SCTP]: Update AUTH structures to match declarations in draft-16.
[SCTP]: Incorrect length was used in SCTP_*_AUTH_CHUNKS socket option
[SCTP]: Clean up naming conventions of sctp protocol/address family registration
[APPLETALK]: Use proc_create() to setup ->proc_fops first
[BNX2X]: add bnx2x to MAINTAINERS
[BNX2X]: update version, remove CVS strings
[BNX2X]: Fix Xmit bugs
[BNX2X]: Prevent PCI queue overflow
...
Linus Torvalds [Fri, 29 Feb 2008 16:29:30 +0000 (08:29 -0800)]
Merge git://git./linux/kernel/git/davem/sparc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Adjust kernel PC validation test in fault handler.
[SPARC64]: Loosen checks in exception table handling.
[SPARC64]: Fix section mismatch from kernel_map_range
[SPARC64]: Fix section mismatchs from dr_cpu_data
[SPARC]: Fix build in arch/sparc/kernel/led.c
Linus Torvalds [Fri, 29 Feb 2008 16:28:46 +0000 (08:28 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
MAINTAINERS: neteffect update
RDMA/nes: Fix interrupt moderation low threshold
RDMA/nes: Fix CRC endianness for RDMA connection establishment on big-endian
RDMA/nes: Fix use-after-free in mini_cm_dec_refcnt_listen()
RDMA/nes: Fix use-after-free in nes_create_cq()
RDMA/nes: Fix a check-after-use in nes_probe()
RDMA/nes: Fix a memory leak in schedule_nes_timer()
RDMA/nes: Fix off-by-one
RDMA/nes: Resurrect error path dead code
RDMA/cxgb3: Fix shift calc in build_phys_page_list() for 1-entry page lists
Linus Torvalds [Fri, 29 Feb 2008 16:27:32 +0000 (08:27 -0800)]
Merge git://git./linux/kernel/git/bart/ide-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: remove stale comments from ide-dma.c (take 2)
ide: remove ide-tape documentation from Documentation/ide.txt
qd65xx: remove commented out code
ide-tape: schedule driver for removal after 6 months
ide-disk: add missing printk() KERN_* levels
ide: fix sparse warning about shadowing 'flags' symbol
ide-cd: fix CD/DVD burning
ide-cd: fix 'ireason' handling for REQ_TYPE_ATA_PC requests
qd65xx: fix setup of QD6580 Control register
ide: skip probing port if "hdx=noprobe" was used for both devices on it
ide: remove redundant comment from ide_unregister()
hpt366: fix section mismatch warnings
ide-cd: Enable audio play quirk for Optiarc DVD RW AD-5200A drive
David Howells [Thu, 28 Feb 2008 13:29:43 +0000 (13:29 +0000)]
Fix hpet_(un)register_irq_handler() for emulation
Fix hpet_(un)register_irq_handler() for when CONFIG_HPET_EMULATE_RTC=n. They
are provided macros that substitute value 0, but if they are called as
functions and the return value isn't checked, the following warnings appear:
drivers/char/rtc.c: In function `rtc_init':
drivers/char/rtc.c:1063: warning: statement with no effect
drivers/char/rtc.c: In function `rtc_exit':
drivers/char/rtc.c:1157: warning: statement with no effect
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Roland McGrath [Tue, 26 Feb 2008 21:20:58 +0000 (13:20 -0800)]
elfcore-compat fix uid/gid types
I overlooked the difference between __kernel_uid_t and uid_t when defining
struct compat_elf_prpsinfo. The result is a regression in 32-bit core
dumps on x86_64, where the NT_PRPSINFO note has the wrong size and layout.
This patch fixes it.
Signed-off-by: Roland McGrath <roland@redhat.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Takashi Iwai [Wed, 27 Feb 2008 15:40:18 +0000 (16:40 +0100)]
[ALSA] intel8x0 - Add quirk for Compaq Deskpro EN
Added the ac97_quirk hp_only for Compaq Deskpro EN.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Herton Ronaldo Krzesinski [Sat, 23 Feb 2008 10:34:12 +0000 (11:34 +0100)]
[ALSA] hda-codec - Adapt eeepc p701 mixer for virtual master control
Fix the line-out volume control of eeepc p701 to be a proper slave of
the virtual master control.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Harvey Harrison [Fri, 29 Feb 2008 10:46:32 +0000 (11:46 +0100)]
[ALSA] sound: ice1712: unused structs
Don't need to declare a struct when defining a structure layout. Both
of these structs are unused.
sound/pci/ice1712/revo.c:39:3: warning: symbol 'revo51' was not declared. Should it be static?
sound/pci/ice1712/phase.c:54:3: warning: symbol 'phase28' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Jarkko Nikula [Thu, 28 Feb 2008 11:35:25 +0000 (12:35 +0100)]
[ALSA] ASoC: Fix WM9712 mixer_event DAPM widget function type
Add kcontrol argument to function since the API was changed by the commit
9af6d9562414568ecadf96aaef5b88e7e8b19821.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Jarkko Nikula [Thu, 28 Feb 2008 11:34:48 +0000 (12:34 +0100)]
[ALSA] ASoC: Fix DAPM widget function types in pxa machine drivers
Add kcontrol argument to functions since the API was changed by the commit
9af6d9562414568ecadf96aaef5b88e7e8b19821.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Wed, 27 Feb 2008 15:10:44 +0000 (16:10 +0100)]
[ALSA] hda-codec - Fix mixer names of realtek codecs to adapt mater controls
Some models like eeepc ep20 have invalid mixer names that aren't
handled properly by virtual master controls. Rename them to the
proper names.
Also fixed some typos in the mixer names but they are not compiled
in right now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Mon, 4 Feb 2008 13:00:53 +0000 (14:00 +0100)]
[ALSA] intel8x0 - Add quirk for Acer Travelmate 2310
Added ac97_quirk=hp-only for Acer Travelmate 2310.
ALSA bug#3656
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3656
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Andrew Paprocki [Sun, 3 Feb 2008 09:15:44 +0000 (10:15 +0100)]
[ALSA] hda_intel - Add model quirk for Albatron KI690-AM2 motherboard
This adds a quirk to the Realtek ALC883 table for the Albatron KI690-AM2
motherboard to use the 6stack-dig model.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clemens Ladisch [Tue, 26 Feb 2008 07:40:57 +0000 (08:40 +0100)]
[ALSA] oxygen: add owner field
I forgot to set the module owner for the HiFier/Xonar models.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tony Vroon [Mon, 25 Feb 2008 15:44:13 +0000 (16:44 +0100)]
[ALSA] hda-codec - Add Fujitsu Lifebook E8410 to quirk table
Add the proper model entry for Fujitsu Lifebook E8410 with ALC262 codec.
From: Tony Vroon <tony@linx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Mon, 25 Feb 2008 14:32:01 +0000 (15:32 +0100)]
[ALSA] hda-codec - Fix AD1988 capture elements
The some indices of capture elements of AD1988 are wrongly assigned.
This patch fixes it. See ALSA bug#3795
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3795
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clemens Ladisch [Mon, 25 Feb 2008 10:04:41 +0000 (11:04 +0100)]
[ALSA] sb8: fix SB 1.0 capture DMA programming
Fix a wrong version check that would cause an invalid command to be sent
to SB 1.0 chips.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clemens Ladisch [Mon, 25 Feb 2008 10:01:00 +0000 (11:01 +0100)]
[ALSA] usb-audio: add workaround for broken E-Mu frequency feedback
Add a workaround for the feedback pipe of E-Mu 0202/0404 USB devices
that reports the number of samples per packet instead of the number of
samples per microframe.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Jarkko Nikula [Wed, 20 Feb 2008 16:13:15 +0000 (17:13 +0100)]
[ALSA] ASoC: Fix TLV320AIC3X PLL divider table for 64 kHz rate
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Mon, 18 Feb 2008 11:36:11 +0000 (12:36 +0100)]
[ALSA] hda-codec - Fix Master volume on HP dv8000
HP dv8000 laptop has a problem with Master volume. It's due to the
connection of the widget 0x13. When it's connected from the analog
amp mixer (0x19), it works as expected mysteriously (ALSA bug#3775):
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3775
Signed-off-by: Takashi Iwai <tiwai@suse.de>
David S. Miller [Fri, 29 Feb 2008 04:38:15 +0000 (20:38 -0800)]
[SPARC64]: Adjust kernel PC validation test in fault handler.
Because of the new futex validation init handler, we have
to accept faults in init section text as well as the normal
kernel text.
Thanks to Tom Callaway for the bug report.
Signed-off-by: David S. Miller <davem@davemloft.net>
Josef Jeff Sipek [Fri, 29 Feb 2008 02:58:40 +0000 (13:58 +1100)]
[XFS] If you mount an XFS filesystem with no mount options at all, then
the "ikeep" option is set rather than "noikeep".
This regression was introduced in 970451.
With no mount options specified, xfs_parseargs() does the following:
int ikeep = 0;
args->flags |= XFSMNT_BARRIER;
args->flags2 |= XFSMNT2_COMPAT_IOSIZE;
if (!options)
goto done;
It only sets the above two options by default and before, it also used to
set XFSMNT_IDELETE by default.
If options are specified, then
if (!(args->flags & XFSMNT_DMAPI) && !ikeep)
args->flags |= XFSMNT_IDELETE;
is executed later on which is skipped by the "goto done;" above.
The solution is to invert the logic.
SGI-PV: 977771
SGI-Modid: xfs-linux-melb:xfs-kern:30590a
Signed-off-by: Niv Sardi <xaiki@sgi.com>
Signed-off-by: Barry Naujok <bnaujok@sgi.com>
Signed-off-by: Josef 'Jeff' Sipek <jeffpc@josefsipek.net>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Sonic Zhang [Fri, 29 Feb 2008 04:08:42 +0000 (12:08 +0800)]
Blackfin Serial Driver: Fix bug - Only insert UART rx char in timer task.
http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=3910
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Wang Chen [Thu, 28 Feb 2008 22:16:33 +0000 (14:16 -0800)]
[X25]: Use proc_create() to setup ->proc_fops first
Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Thu, 28 Feb 2008 22:15:56 +0000 (14:15 -0800)]
[WANROUTER]: Use proc_create() to setup ->proc_fops first
Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Thu, 28 Feb 2008 22:14:58 +0000 (14:14 -0800)]
[8021Q]: Use proc_create() to setup ->proc_fops first
Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Thu, 28 Feb 2008 22:14:25 +0000 (14:14 -0800)]
[IPV4]: Use proc_create() to setup ->proc_fops first
Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Thu, 28 Feb 2008 22:13:46 +0000 (14:13 -0800)]
[IPV6]: Use proc_create() to setup ->proc_fops first
Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Thu, 28 Feb 2008 22:13:16 +0000 (14:13 -0800)]
[SCTP]: Use proc_create() to setup ->proc_fops first
Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Thu, 28 Feb 2008 22:11:49 +0000 (14:11 -0800)]
[PKTGEN]: Use proc_create() to setup ->proc_fops first
Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Thu, 28 Feb 2008 22:10:51 +0000 (14:10 -0800)]
[NEIGHBOUR]: Use proc_create() to setup ->proc_fops first
Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Thu, 28 Feb 2008 22:08:54 +0000 (14:08 -0800)]
[LLC]: Use proc_create() to setup ->proc_fops first
Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Thu, 28 Feb 2008 22:06:14 +0000 (14:06 -0800)]
[IPX]: Use proc_create() to setup ->proc_fops first
Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Thu, 28 Feb 2008 22:00:59 +0000 (14:00 -0800)]
[SUNRPC]: Use proc_create() to setup ->proc_fops first
Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 28 Feb 2008 21:56:37 +0000 (13:56 -0800)]
Merge branch 'pending' of /linux/kernel/git/vxy/lksctp-dev
Wang Chen [Thu, 28 Feb 2008 21:55:45 +0000 (13:55 -0800)]
[ATM]: Use proc_create() to setup ->proc_fops first
Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Wed, 27 Feb 2008 21:04:52 +0000 (16:04 -0500)]
[SCTP]: Update AUTH structures to match declarations in draft-16.
The new SCTP socket api (draft 16) updates the AUTH API structures.
We never exported these since we knew they would change.
Update the rest to match the draft.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Vlad Yasevich [Wed, 27 Feb 2008 19:40:37 +0000 (14:40 -0500)]
[SCTP]: Incorrect length was used in SCTP_*_AUTH_CHUNKS socket option
The chunks are stored inside a parameter structure in the kernel
and when we copy them to the user, we need to account for
the parameter header.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Neil Horman [Fri, 15 Feb 2008 14:53:59 +0000 (09:53 -0500)]
[SCTP]: Clean up naming conventions of sctp protocol/address family registration
I noticed while looking into some odd behavior in sctp, that the variable
name sctp_pf_inet6_specific was used twice to represent two different
pieces of data (its both a structure name and a pointer to that type of
structure), which is confusing to say the least, and potentially dangerous
depending on the variable scope. This patch cleans that up, and makes the
protocol and address family registration names in SCTP more regular,
increasing readability.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
ipv6.c | 12 ++++++------
protocol.c | 12 ++++++------
2 files changed, 12 insertions(+), 12 deletions(-)
Wang Chen [Thu, 28 Feb 2008 20:53:32 +0000 (12:53 -0800)]
[APPLETALK]: Use proc_create() to setup ->proc_fops first
As Davem mentioned in his recently patch
(
d9595a7b9c777d45a74774f1428c263a0a47f4c0)
that the procfs visibility should occur after
the ->proc_fops are setup.
And also, Alexey provide proc_create() to make
sure that ->proc_fops is setup before gluing PDE
to main tree.
We use proc_create().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliezer Tamir [Thu, 28 Feb 2008 19:59:10 +0000 (11:59 -0800)]
[BNX2X]: add bnx2x to MAINTAINERS
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliezer Tamir [Thu, 28 Feb 2008 19:58:49 +0000 (11:58 -0800)]
[BNX2X]: update version, remove CVS strings
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliezer Tamir [Thu, 28 Feb 2008 19:57:55 +0000 (11:57 -0800)]
[BNX2X]: Fix Xmit bugs
Several endianity corrections in start_xmit()
Fixed TSO bug where packets were missing the TCP flags.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliezer Tamir [Thu, 28 Feb 2008 19:57:29 +0000 (11:57 -0800)]
[BNX2X]: Prevent PCI queue overflow
Limit traffic through an internal queue to prevent overflow.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliezer Tamir [Thu, 28 Feb 2008 19:56:57 +0000 (11:56 -0800)]
[BNX2X]: fix slowpath races and locking
Fixed locking between fastpath and slowpath operations.
Corrected order of traffic disabling to prevent race when going down
under traffic.
- first have the microcode drop all incoming packets
- then do the slowpath stuff
- only then reset the MAC
Got rid of in_reset_task.
Remove_one() and friends would deference a null pointer if init_one
failed.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliezer Tamir [Thu, 28 Feb 2008 19:55:53 +0000 (11:55 -0800)]
[BNX2X]: fix HW attentions and error handling
Some of the HW attentions, used to indicate an error were not properly
acked.
This will cause the driver to endlessly receive interrupts when such
an error happens.
Had to break the code into smaller chunks because it got too nested.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliezer Tamir [Thu, 28 Feb 2008 19:54:54 +0000 (11:54 -0800)]
[BNX2X]: fix MSI-X/INT#A errata
Errata A0.158 workaround.
Running in INT#A mode after running with MSI-X fails due to a PCI core
bug.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliezer Tamir [Thu, 28 Feb 2008 19:54:03 +0000 (11:54 -0800)]
[BNX2X]: correct statistics
Errors were summed improperly, some stats were missing.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliezer Tamir [Thu, 28 Feb 2008 19:53:13 +0000 (11:53 -0800)]
[BNX2X]: Correct RX filtering and MC configuration
The configuration of RX filtering needed the following corrections:
Drop flags need to be set per Rx queue.
Have to tell the microcode to collect drop stats, and properly wait
for them to complete when going down.
Sometimes we failed to detect proper completion due to a logical error
in the wait loop.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliezer Tamir [Thu, 28 Feb 2008 19:51:50 +0000 (11:51 -0800)]
[BNX2X]: Correct Link management
Properly protect PHY access between two devices on the same board with
a HW lock.
Use GPIO to clear all previous configurations before changing link
parameters.
Shut down the external PHY in case of fan failure.
Reducing the MDC/MDIO clock to 2.5MHz due to problems with some
devices.
Resolve the flow control response according to autoneg with external
PHY.
Unmasking all PHY interrupts in single write to prevent a race in the
interrupts order.
LASI indication fixes to work with peculiarities of PHYs.
Disable MAC RX to avoid a HW bug when closing the MAC under traffic.
Disable parallel detection on HiGig due to HW limitation.
Updating the shared memory structure to work with the current
bootcode.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliezer Tamir [Thu, 28 Feb 2008 19:50:16 +0000 (11:50 -0800)]
[BNX2X]: Correct init_one()
Correct PCI-E info printed by init_one()
In one case it failed to free the netdev.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliezer Tamir [Thu, 28 Feb 2008 19:49:42 +0000 (11:49 -0800)]
[BNX2X]: Spelling fixes
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Thu, 28 Feb 2008 19:23:17 +0000 (11:23 -0800)]
[IPCOMP]: Disable BH on output when using shared tfm
Because we use shared tfm objects in order to conserve memory,
(each tfm requires 128K of vmalloc memory), BH needs to be turned
off on output as that can occur in process context.
Previously this was done implicitly by the xfrm output code.
That was lost when it became lockless. So we need to add the
BH disabling to IPComp directly.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 28 Feb 2008 19:03:29 +0000 (11:03 -0800)]
Merge branch 'master' of /linux/kernel/git/linville/wireless-2.6
Aurelien Jarno [Thu, 28 Feb 2008 14:11:26 +0000 (15:11 +0100)]
SSB PCI core driver: use new SPROM data structure
Switch the SSB PCI core driver to the new SPROM data structure now that
the old one has been removed.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alexey Zaytsev [Sat, 23 Feb 2008 10:33:07 +0000 (13:33 +0300)]
Don't build bcm43xx if SSB is static and b43 PCI-SSB bridge is enabled.
This may happen e.g. when the ssb is statically enables by the b44 driver,
and the b43 pci-ssb bridge is enbled by the b43/b43legacy drivers, or the
b43/b43legacy drivers are built statically.
Signed-off-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alexey Zaytsev [Sat, 23 Feb 2008 09:59:26 +0000 (12:59 +0300)]
Use a separate config option for the b43 pci to ssb bridge.
The bridge code was unnecessary enabled by the b44
driver, but it prevents the bcm43xx driver from
being loaded, as the bridge claims the same pci ids.
Now we enable the birdge only if the b43{legacy}
drivers are selected.
Signed-off-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Roland Dreier [Tue, 26 Feb 2008 14:26:56 +0000 (15:26 +0100)]
libertas: Remove unused exports
The libertas driver exports a number of symbols with no in-tree users;
remove these unused exports. lbs_reset_device() is completely unused, with
no callers at all, so remove the function completely.
A couple of these unused exported symbols are static, which causes the
following build error on ia64 with gcc 4.2.3:
drivers/net/wireless/libertas/main.c:1375: error: __ksymtab_lbs_remove_mesh causes a section type conflict
drivers/net/wireless/libertas/main.c:1354: error: __ksymtab_lbs_add_mesh causes a section type conflict
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 25 Feb 2008 23:39:28 +0000 (00:39 +0100)]
mac80211: fix kmalloc vs. net_ratelimit
The "goto end;" part definitely must not be rate limited.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 25 Feb 2008 22:15:13 +0000 (23:15 +0100)]
rt2x00: Fix rt2x00lib_reset_link_tuner()
rt2x00lib_reset_link_tuner() can be called from within
the link tuner itself. This means that it should
_not_ call rt2x00lib_stop_link_tuner() since that will
cause the thread to hang.
Reorder the things that should be done during a
link tuner reset and during a link tuner start.
Also make antenna tuning the last step of the link
tuner since it could possibly reset some statistical
information which we need for average calculation.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 25 Feb 2008 22:15:08 +0000 (23:15 +0100)]
rt2x00: Don't switch to antenna with low rssi
When rssi_a > rssi_b is true and the current antenna
was already antenna A, then rt2x00 incorrectly jumped
to antenna B.
Also don't configure the antenna when there has been
no change in the antenna setup.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 25 Feb 2008 22:15:05 +0000 (23:15 +0100)]
rt2x00: Add link tuner safe RX toggle states
This adds 2 new states which both are used to toggle
the RX. These new states are required for usage
inside the link tuner thread, because the normal
RX toggling will stop the link tuner thread.
While it is possible that the link tuner thread itself
is the caller of the RX toggle (when using software
antenna diversity).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 25 Feb 2008 22:15:01 +0000 (23:15 +0100)]
rt2x00: Fix antenna diversity
Fix 2 issues in antenna diversity selection.
1) the following statement will always return true.
if ((rssi_curr - rssi_old) > -5 || (rssi_curr - rssi_old) < 5)
It is cleaner to check if the absolute value is smaller then 5.
2) Only enable software diversity when default antenna setup
indicates support for it. Don't select it when the hardware
does not indicate support for it...
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sebastian Siewior [Sat, 23 Feb 2008 20:46:31 +0000 (21:46 +0100)]
gelic wireless driver needs WIRELESS_EXT support
| CC drivers/net/ps3_gelic_wireless.o
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c: In function 'gelic_wl_setup_netdev_ops':
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c:2660: error: 'struct net_device' has no member named 'wireless_data'
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c:2661: error: 'struct net_device' has no member named 'wireless_handlers'
| make[3]: *** [drivers/net/ps3_gelic_wireless.o] Error 1
| make[2]: *** [drivers/net] Error 2
| make[1]: *** [drivers] Error 2
| make[1]: *** Waiting for unfinished jobs....
| make: *** [sub-make] Error 2
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Acked-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Masakazu Mokuno [Fri, 22 Feb 2008 07:45:26 +0000 (16:45 +0900)]
PS3: gelic: Link the wireless net_device structure to the corresponding device structure
Link the net_device structure of the wireless part to the
corresponding device structure.
Without this, the sysfs node for this net_device would not have
'device' link.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 20 Feb 2008 10:47:45 +0000 (11:47 +0100)]
rndis_wlan: fix sparse warnings
It is obviously wrong to use an enum in a little endian struct,
and those other enums should be declared differently.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vlad Yasevich [Thu, 14 Feb 2008 15:18:20 +0000 (10:18 -0500)]
[SCTP]: Correctly set the length of sctp_assoc_change notification
sctp_assoc_change notification may contain the data from a received
ABORT chunk. Set the length correctly to account for that.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Patrick McHardy [Wed, 27 Feb 2008 20:21:18 +0000 (12:21 -0800)]
[NETFILTER]: Fix NF_QUEUE_NR() parenthesis
Properly add parens around the macro argument. This is not needed by
the kernel but the macro is exported to userspace, so it shouldn't
make any assumptions.
Also use NF_VERDICT_BITS instead of NF_VERDICT_QBTIS for the left-shift
since thats whats logically correct.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Engelhardt [Wed, 27 Feb 2008 20:20:41 +0000 (12:20 -0800)]
[NETFILTER]: xt_conntrack: fix IPv4 address comparison
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Engelhardt [Wed, 27 Feb 2008 20:09:05 +0000 (12:09 -0800)]
[NETFILTER]: xt_conntrack: fix missing boolean clamping
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Wed, 27 Feb 2008 20:07:47 +0000 (12:07 -0800)]
[NETFILTER]: nf_conntrack: fix smp_processor_id() in preemptible code warning
Since we're using RCU for the conntrack hash now, we need to avoid
getting preempted or interrupted by BHs while changing the stats.
Fixes warning reported by Tilman Schmidt <tilman@imap.cc> when using
preemptible RCU:
[ 48.180297] BUG: using smp_processor_id() in preemptible [
00000000] code: ntpdate/3562
[ 48.180297] caller is __nf_conntrack_find+0x9b/0xeb [nf_conntrack]
[ 48.180297] Pid: 3562, comm: ntpdate Not tainted 2.6.25-rc2-mm1-testing #1
[ 48.180297] [<
c02015b9>] debug_smp_processor_id+0x99/0xb0
[ 48.180297] [<
fac643a7>] __nf_conntrack_find+0x9b/0xeb [nf_conntrack]
Tested-by: Tilman Schmidt <tilman@imap.cc>
Tested-by: Christian Casteyde <casteyde.christian@free.fr> [Bugzilla #10097]
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
YOSHIFUJI Hideaki [Wed, 27 Feb 2008 20:06:38 +0000 (12:06 -0800)]
[IPV6] SYSCTL: Fix possible memory leakage in error path.
In error path, we do need to free memory just allocated.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Haavard Skinnemoen [Wed, 27 Feb 2008 13:04:29 +0000 (14:04 +0100)]
avr32: Fix OCD refcounting bug
Iff the parent has TIF_DEBUG set, _and_ clone_flags includes
CLONE_PTRACE we should set the TIF_DEBUG flag for the child and
increment the ocd refcount. Otherwise, the TIF_DEBUG flag must be
unset.
Currently, the child inherits TIF_DEBUG from the parent before
copy_thread is called, so TIF_DEBUG may be already be set before we
determine whether the child is supposed to inherit debugging
capabilities from the parent or not. This means that ocd_enable()
won't increment the refcount, because TIF_DEBUG is already set, and
that TIF_DEBUG will be set for processes that aren't being debugged.
This leads to a refcounting asymmetry, which may show up as
------------[ cut here ]------------
Badness at arch/avr32/kernel/ocd.c:73
PC is at ocd_disable+0x34/0x60
LR is at put_lock_stats+0xa/0x20
as reported by David Brownell. Happens when strace'ing a process that
forks a new child process, e.g. "strace mount -tjffs2 mtd1 /mnt", and
subsequently killing the child process (e.g. "umount /mnt".)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Pavel Emelyanov [Wed, 27 Feb 2008 07:51:04 +0000 (23:51 -0800)]
[INET]: Don't create tunnels with '%' in name.
Four tunnel drivers (ip_gre, ipip, ip6_tunnel and sit) can receive a
pre-defined name for a device from the userspace. Since these drivers
call the register_netdevice() (rtnl_lock, is held), which does _not_
generate the device's name, this name may contain a '%' character.
Not sure how bad is this to have a device with a '%' in its name, but
all the other places either use the register_netdev(), which call the
dev_alloc_name(), or explicitly call the dev_alloc_name() before
registering, i.e. do not allow for such names.
This had to be prior to the commit 34cc7b, but I forgot to number the
patches and this one got lost, sorry.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 27 Feb 2008 06:20:44 +0000 (22:20 -0800)]
[AF_KEY]: Fix oops by converting to proc_net_*().
To make sure the procfs visibility occurs after the ->proc_fs ops are
setup, use proc_net_fops_create() and proc_net_remove().
This also fixes an OOPS after module unload in that the name string
for remove was wrong, so it wouldn't actually be removed. That bug
was introduced by commit
61145aa1a12401ac71bcc450a58c773dd6e2bfb9
("[KEY]: Clean up proc files creation a bit.")
Signed-off-by: David S. Miller <davem@davemloft.net>
Li Zefan [Wed, 27 Feb 2008 02:25:53 +0000 (18:25 -0800)]
CONNECTOR: make cn_already_initialized static
It is used in connector.c only, so make it static.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjorn Mork [Wed, 27 Feb 2008 02:17:53 +0000 (18:17 -0800)]
[IPV4]: Reset scope when changing address
This bug did bite at least one user, who did have to resort to rebooting
the system after an "ifconfig eth0 127.0.0.1" typo.
Deleting the address and adding a new is a less intrusive workaround.
But I still beleive this is a bug that should be fixed. Some way or
another.
Another possibility would be to remove the scope mangling based on
address. This will always be incomplete (are 127/8 the only address
space with host scope requirements?)
We set the scope to RT_SCOPE_HOST if an IPv4 interface is configured
with a loopback address (127/8). The scope is never reset, and will
remain set to RT_SCOPE_HOST after changing the address. This patch
resets the scope if the address is changed again, to restore normal
functionality.
Signed-off-by: Bjorn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Thery [Wed, 27 Feb 2008 02:10:03 +0000 (18:10 -0800)]
[IPV6]: Add missing initializations of the new nl_info.nl_net field
Add some more missing initializations of the new nl_info.nl_net field
in IPv6 stack. This field will be used when network namespaces are
fully supported.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Wed, 27 Feb 2008 01:52:05 +0000 (17:52 -0800)]
[MACVLAN]: Update Kconfig to refer to iproute
Since the macvlan release I had at least 5 users asking how to configure
it since the old userspace tool doesn't work with the version in the
kernel. Add a pointer to the Kconfig help.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Gleixner [Wed, 27 Feb 2008 01:42:56 +0000 (17:42 -0800)]
bluetooth: delete timer in l2cap_conn_del()
Delete a possibly armed timer before kfree'ing the connection object.
Solves: http://lkml.org/lkml/2008/2/15/514
Reported-by:Quel Qun <kelk1@comcast.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 27 Feb 2008 01:30:02 +0000 (17:30 -0800)]
[SPARC64]: Loosen checks in exception table handling.
Some parts of the kernel now do things like do *_user() accesses while
set_fs(KERNEL_DS) that fault on purpose.
See, for example, the code added by changeset
a0c1e9073ef7428a14309cba010633a6cd6719ea ("futex: runtime enable pi
and robust functionality").
That trips up the ASI sanity checking we make in do_kernel_fault().
Just remove it for now. Maybe we can add it back later with an added
conditional which looks at the current get_fs() value.
Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Tue, 26 Feb 2008 20:42:11 +0000 (21:42 +0100)]
arch/sh/drivers/dma/dma-sh.c: Correct use of ! and &
In commit
e6bafba5b4765a5a252f1b8d31cbf6d2459da337, a bug was fixed that
involved converting !x & y to !(x & y). The code below shows the same
pattern, and thus should perhaps be fixed in the same way.
This is not tested and clearly changes the semantics, so it is only
something to consider.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@ expression E1,E2; @@
(
!E1 & !E2
|
- !E1 & E2
+ !(E1 & E2)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Roland Dreier [Thu, 21 Feb 2008 15:02:41 +0000 (09:02 -0600)]
MAINTAINERS: neteffect update
Adding Nishi to the maintainers list.
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
John Lacombe [Thu, 21 Feb 2008 14:34:58 +0000 (08:34 -0600)]
RDMA/nes: Fix interrupt moderation low threshold
Interrupt moderation low threshold value was incorrectly triggering,
indicating that the threshold should be lowered.
The impact was the timer was likely to become 40usecs and get stuck
there. The biggest side effect was too many interrupts and nonoptimal
performance.
Signed-off-by: John Lacombe <jlacombe@neteffect.com>
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Faisal Latif [Thu, 21 Feb 2008 14:31:22 +0000 (08:31 -0600)]
RDMA/nes: Fix CRC endianness for RDMA connection establishment on big-endian
With commit
ef19454b ("[LIB] crc32c: Keep intermediate crc state in
cpu order"), the behavior of crc32c changes on big-endian platforms.
Our algorithm expects the previous behavior; otherwise we have RDMA
connection establishment failure on big-endian platforms like powerpc.
Apply cpu_to_le32() to value returned by crc32c() to get the previous
behavior.
Signed-off-by: Faisal Latif <flatif@neteffect.com>
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Faisal Latif [Thu, 21 Feb 2008 14:27:32 +0000 (08:27 -0600)]
RDMA/nes: Fix use-after-free in mini_cm_dec_refcnt_listen()
Fix use-after-free spotted by Coverity checker flagged by Adrian Bunk.
Signed-off-by: Faisal Latif <flatif@neteffect.com>
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Glenn Streiff [Thu, 21 Feb 2008 14:17:54 +0000 (08:17 -0600)]
RDMA/nes: Fix use-after-free in nes_create_cq()
Just delete the debugging statement so we don't use cqp_request after
freeing it. Adrian Bunk flagged this use-after-free issue spotted by
the Coverity checker.
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Adrian Bunk [Thu, 21 Feb 2008 14:13:47 +0000 (08:13 -0600)]
RDMA/nes: Fix a check-after-use in nes_probe()
Fix a check-after-use spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Adrian Bunk [Thu, 21 Feb 2008 14:12:06 +0000 (08:12 -0600)]
RDMA/nes: Fix a memory leak in schedule_nes_timer()
Fix a memory leak spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Bartlomiej Zolnierkiewicz [Tue, 26 Feb 2008 20:50:36 +0000 (21:50 +0100)]
ide: remove stale comments from ide-dma.c (take 2)
- ide-dma.c is not a separate module
- ide-dma.c is not PCI specific anymore
- DMA is enabled by default nowadays
- link for Intel Zappa BIOS is dead
etc.
v2:
* Some comments should be preserved. (Noticed by Mark Lord)
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Tue, 26 Feb 2008 20:50:36 +0000 (21:50 +0100)]
ide: remove ide-tape documentation from Documentation/ide.txt
More complete documentation is available in Documentation/ide/ide-tape.txt.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>