openwrt/staging/blogic.git
6 years agomlxsw: spectrum_ipip: Support decoding IPv6 tunnel addresses
Petr Machata [Tue, 27 Feb 2018 13:53:36 +0000 (14:53 +0100)]
mlxsw: spectrum_ipip: Support decoding IPv6 tunnel addresses

To support mirroring to ip6gretap, the SPAN module needs to be able to
decode IPv6 addresses specified at that tunnel.

Extend mlxsw_sp_ipip_netdev_saddr() and mlxsw_sp_ipip_netdev_daddr() to
support IPv6 addresses. To that end, add and publish a support function
mlxsw_sp_ipip_netdev_parms6().

Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agomlxsw: spectrum_ipip: Extract mlxsw_sp_l3addr_is_zero
Petr Machata [Tue, 27 Feb 2018 13:53:35 +0000 (14:53 +0100)]
mlxsw: spectrum_ipip: Extract mlxsw_sp_l3addr_is_zero

Extract the logic for determining whether a given IPv4/IPv6 address is
all-zeroes from mlxsw_sp_ipip_tunnel_complete to a separate function.
Make that function public within the module.

Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agoMerge branch 'ibmvnic-Miscellaneous-driver-fixes-and-enhancements'
David S. Miller [Tue, 27 Feb 2018 19:31:20 +0000 (14:31 -0500)]
Merge branch 'ibmvnic-Miscellaneous-driver-fixes-and-enhancements'

Thomas Falcon says:

====================
ibmvnic: Miscellaneous driver fixes and enhancements

There is not a general theme to this patch set other than that it
fixes a few issues with the ibmvnic driver. I will just give a quick
summary of what each patch does here.

"ibmvnic: Fix TX descriptor tracking again" resolves a race condition
introduced in an earlier fix to track outstanding transmit descriptors.
This condition can throw off the tracking counter to the point that
a transmit queue will halt forever.

"ibmvnic: Allocate statistics buffers during probe" allocates queue
statistics buffers on device probe to avoid a crash when accessing
statistics of an unopened interface.

"ibmvnic: Harden TX/RX pool cleaning" includes additional checks to
avoid a bad access when cleaning RX and TX buffer pools during a device
reset.

"ibmvnic: Report queue stops and restarts as debug output" changes TX
queue state notifications from informational to debug messages. This
information is not necessarily useful to a user and under load can result
in a lot of log output.

"ibmvnic: Do not attempt to login if RX or TX queues are not allocated"
checks that device queues have been allocated successfully before
attempting device login. This resolves a panic that could occur if a
user attempted to configure a device after a failed reset.

Thanks for your attention.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agoibmvnic: Do not attempt to login if RX or TX queues are not allocated
Thomas Falcon [Tue, 27 Feb 2018 00:10:59 +0000 (18:10 -0600)]
ibmvnic: Do not attempt to login if RX or TX queues are not allocated

If a device reset fails for some reason, TX and RX queue resources
could be released. If a user attempts to open the device in this scenario,
it may result in a kernel panic as the driver tries to access this
memory. To fix this, include a check before device login that TX/RX
queues are still there before enabling the device. In addition, return a
value that can be checked in case of any errors to avoid waiting for a
completion that will never come.

Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agoibmvnic: Report queue stops and restarts as debug output
Thomas Falcon [Tue, 27 Feb 2018 00:10:58 +0000 (18:10 -0600)]
ibmvnic: Report queue stops and restarts as debug output

It's not necessary to report each time a queue is stopped and restarted
as an informational message. Change that to be a debug message so that
it can be observed if needed but not printed by default.

Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agoibmvnic: Harden TX/RX pool cleaning
Thomas Falcon [Tue, 27 Feb 2018 00:10:57 +0000 (18:10 -0600)]
ibmvnic: Harden TX/RX pool cleaning

If the driver releases resources after a failed reset or some other
error, the driver might attempt to clean up and free memory that
isn't there anymore. Include some additional checks that RX/TX queues
along with their associated structures are still there before cleaning.

Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agoibmvnic: Allocate statistics buffers during probe
Thomas Falcon [Tue, 27 Feb 2018 00:10:56 +0000 (18:10 -0600)]
ibmvnic: Allocate statistics buffers during probe

Currently, buffers holding individual queue statistics are allocated
when the device is opened. If an ibmvnic interface is hotplugged or
initialized but never opened, an attempt to get statistics with
ethtool will result in a kernel panic.

Since the driver allocates a constant number, the maximum supported
queues, of buffers, these can be allocated during device probe and
freed when the device is hot-unplugged or the module is removed.

Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agoibmvnic: Fix TX descriptor tracking again
Thomas Falcon [Tue, 27 Feb 2018 00:10:55 +0000 (18:10 -0600)]
ibmvnic: Fix TX descriptor tracking again

Sorry, the previous change introduced a race condition between
transmit completion processing and tracking TX descriptors. If a
completion is received before the number of descriptors is logged,
the number of descriptors will be add but not removed. After enough
times, this could halt the transmit queue forever.

Log the number of descriptors used by a transmit before sending.
I stress tested the fix on two different systems running over the
weekend without any issues.

Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agoMerge branch 'stmmac-barrier-fixes-and-cleanup'
David S. Miller [Tue, 27 Feb 2018 19:28:11 +0000 (14:28 -0500)]
Merge branch 'stmmac-barrier-fixes-and-cleanup'

Niklas Cassel says:

====================
stmmac barrier fixes and cleanup
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: stmmac: make dwmac4_release_tx_desc() clear all descriptor fields
Niklas Cassel [Mon, 26 Feb 2018 21:47:09 +0000 (22:47 +0100)]
net: stmmac: make dwmac4_release_tx_desc() clear all descriptor fields

Make dwmac4_release_tx_desc() clear all descriptor fields, not just
TDES2 and TDES3.

I'm suspecting that TDES0 and TDES1 wasn't cleared because the DMA
engine uses them to store the tx hardware timestamp (if PTP is enabled).

However, stmmac_tx_clean() calls stmmac_get_tx_hwtstamp(), which reads
and saves the timestamp, before it calls release_tx_desc(), so this
is not an issue.

stmmac_xmit() and stmmac_tso_xmit() both always overwrite TDES0,
however, stmmac_tso_xmit() sometimes sets TDES1, and since neither
stmmac_xmit() nor stmmac_tso_xmit() explicitly clears TDES1, both
functions might reuse a DMA descriptor with old TDES1 data.

I haven't observed any misbehavior even though TDES1 sometimes
point to an old skb, however, explicitly clearing both TDES0 and TDES1
in dwmac4_release_tx_desc() minimizes the chances of undefined behavior.

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: stmmac: ensure that the device has released ownership before reading data
Niklas Cassel [Mon, 26 Feb 2018 21:47:08 +0000 (22:47 +0100)]
net: stmmac: ensure that the device has released ownership before reading data

According to Documentation/memory-barriers.txt, we need to use a
dma_rmb() after reading the status/own bit, to ensure that all
descriptor fields are read after reading the own bit.

This way, we ensure that the DMA engine is done with the DMA
descriptor before we read the other descriptor fields, e.g. reading
the tx hardware timestamp (if PTP is enabled).

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: stmmac: use correct barrier between coherent memory and MMIO
Niklas Cassel [Mon, 26 Feb 2018 21:47:07 +0000 (22:47 +0100)]
net: stmmac: use correct barrier between coherent memory and MMIO

The last memory barrier in stmmac_xmit()/stmmac_tso_xmit() is placed
between a coherent memory write and a MMIO write:

The own bit is written in First Desc (TSO: MSS desc or First Desc).
<barrier>
The DMA engine is started by a write to the tx desc tail pointer/
enable dma transmission register, i.e. a MMIO write.

This barrier cannot be a simple dma_wmb(), since a dma_wmb() is only
used to guarantee the ordering, with respect to other writes,
to cache coherent DMA memory.

To guarantee that the cache coherent memory writes have completed
before we attempt to write to the cache incoherent MMIO region,
we need to use the more heavyweight barrier wmb().

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: stmmac: ensure that the MSS desc is the last desc to set the own bit
Niklas Cassel [Mon, 26 Feb 2018 21:47:06 +0000 (22:47 +0100)]
net: stmmac: ensure that the MSS desc is the last desc to set the own bit

A dma_wmb() is used to guarantee the ordering, with respect to
other writes, to cache coherent DMA memory.

There is a dma_wmb() in prepare_tx_desc()/prepare_tso_tx_desc() which
ensures that TDES0/1/2 is written before TDES3 (which contains the own
bit), for First Desc.

However, in the rare case that MSS changes, there will be a MSS
context descriptor in front of the regular DMA descriptors:

<MSS desc> <- DMA Next Descriptor
<First Desc>
<desc n>
<Last Desc>

Thus, for this special case, we need a dma_wmb()
after prepare_tso_tx_desc()/before writing the own bit to the MSS desc,
so that we flush the write to TDES3 for First Desc,
in order to ensure that the MSS descriptor is the last descriptor to
set the own bit.

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agoMerge branch 'RDS-optimized-notification-for-zerocopy-completion'
David S. Miller [Tue, 27 Feb 2018 19:19:11 +0000 (14:19 -0500)]
Merge branch 'RDS-optimized-notification-for-zerocopy-completion'

Sowmini Varadhan says:

====================
RDS: optimized notification for zerocopy completion

Resending with acked-by additions: previous attempt does not show
up in Patchwork. This time with a new mail Message-Id.

RDS applications use predominantly request-response, transacation
based IPC, so that ingress and egress traffic are well-balanced,
and it is possible/desirable to reduce system-call overhead by
piggybacking the notifications for zerocopy completion response
with data.

Moreover, it has been pointed out that socket functions block
if sk_err is non-zero, thus if the RDS code does not plan/need
to use sk_error_queue path for completion notification, it
is preferable to remove the sk_errror_queue related paths in
RDS.

Both of these goals are implemented in this series.

v2: removed sk_error_queue support
v3: incorporated additional code review comments (details in each patch)
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agoselftests/net: reap zerocopy completions passed up as ancillary data.
Sowmini Varadhan [Tue, 27 Feb 2018 17:52:44 +0000 (09:52 -0800)]
selftests/net: reap zerocopy completions passed up as ancillary data.

PF_RDS sockets pass up cookies for zerocopy completion as ancillary
data. Update msg_zerocopy to reap this information.

Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agords: deliver zerocopy completion notification with data
Sowmini Varadhan [Tue, 27 Feb 2018 17:52:43 +0000 (09:52 -0800)]
rds: deliver zerocopy completion notification with data

This commit is an optimization over commit 01883eda72bd
("rds: support for zcopy completion notification") for PF_RDS sockets.

RDS applications are predominantly request-response transactions, so
it is more efficient to reduce the number of system calls and have
zerocopy completion notification delivered as ancillary data on the
POLLIN channel.

Cookies are passed up as ancillary data (at level SOL_RDS) in a
struct rds_zcopy_cookies when the returned value of recvmsg() is
greater than, or equal to, 0. A max of RDS_MAX_ZCOOKIES may be passed
with each message.

This commit removes support for zerocopy completion notification on
MSG_ERRQUEUE for PF_RDS sockets.

Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agoselftests/net: revert the zerocopy Rx path for PF_RDS
Sowmini Varadhan [Tue, 27 Feb 2018 17:52:42 +0000 (09:52 -0800)]
selftests/net: revert the zerocopy Rx path for PF_RDS

In preparation for optimized reception of zerocopy completion,
revert the Rx side changes introduced by Commit dfb8434b0a94
("selftests/net: add zerocopy support for PF_RDS test case")

Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agoMerge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next...
David S. Miller [Tue, 27 Feb 2018 17:56:36 +0000 (12:56 -0500)]
Merge branch '40GbE' of git://git./linux/kernel/git/jkirsher/next-queue

Jeff Kirsher says:

====================
40GbE Intel Wired LAN Driver Updates 2018-02-26

This series contains updates to i40e and i40evf only.

Mariusz adds a new ethtool private flag for forcing true link state with
the requested changes from Jakub Kicinski.

PaweÅ‚ fixes an issue where we were double locking the same resource
which would generate a kernel panic after bringing an interface up for
i40evf.

Alan modifies both drivers to use software values to determine if there
are packets stalled on the ring with the added benefit of being less CPU
intensive since we do not need to reach into the hardware to get the
values.

Colin Ian King provides a few fixes detected by Coverity, first was to
pass a struct by reference versus by value to be more efficient.  Then
verify the VSI pointer is not NULL before trying to dereference it.
Cleaned up redundant checks that always return true.

Dan Carpenter fixes over indented lines of code.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agor8169: improve interrupt handling
Heiner Kallweit [Sat, 24 Feb 2018 15:53:23 +0000 (16:53 +0100)]
r8169: improve interrupt handling

This patch improves few aspects of interrupt handling:
- update to current interrupt allocation API
  (use pci_alloc_irq_vectors() instead of deprecated pci_enable_msi())
- this implicitly will allocate a MSI-X interrupt if available
- get rid of flag RTL_FEATURE_MSI
- remove some dead code, intentionally disabling (unreliable) MSI
  being partially available on old PCI chips.

The patch works fine on a RTL8168evl (chip version 34) and on a
RTL8169SB (chip version 04).

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agoselftests: Add fib-onlink-tests.sh to TEST_PROGS
David Ahern [Mon, 26 Feb 2018 17:53:15 +0000 (09:53 -0800)]
selftests: Add fib-onlink-tests.sh to TEST_PROGS

Fixes: 153e1b84f477 ("selftests: Add FIB onlink tests")
Reported-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agoMerge branch 'DPAA-Ethernet-fixes'
David S. Miller [Tue, 27 Feb 2018 16:40:04 +0000 (11:40 -0500)]
Merge branch 'DPAA-Ethernet-fixes'

Madalin Bucur says:

====================
DPAA Ethernet fixes

Fixed an issue on the Tx path that was visible in netperf
TCP_SENDFILE tests. Addressed another issue with Rx errors
not being always counted. Adding control for allmulti.

v2: rephrased commit message, reduced changes in the SG mapping fix
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agodpaa_eth: Add allmulti option
Radu Bulie [Mon, 26 Feb 2018 17:24:04 +0000 (11:24 -0600)]
dpaa_eth: Add allmulti option

This patch adds allmulticast option for memac, dtsec
and 10GEC controllers.

Signed-off-by: Radu Bulie <radu-andrei.bulie@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agodpaa_eth: refactor frag count checking
Madalin Bucur [Mon, 26 Feb 2018 17:24:03 +0000 (11:24 -0600)]
dpaa_eth: refactor frag count checking

Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agodpaa_eth: make sure all Rx errors are counted
Madalin Bucur [Mon, 26 Feb 2018 17:24:02 +0000 (11:24 -0600)]
dpaa_eth: make sure all Rx errors are counted

Simplify the code and avoid some Rx errors not being
accounted.

Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agodpaa_eth: fix SG mapping
Madalin Bucur [Mon, 26 Feb 2018 17:24:01 +0000 (11:24 -0600)]
dpaa_eth: fix SG mapping

An issue in the code mapping the skb fragments into
scatter-gather frames was evidentiated by netperf
TCP_SENDFILE tests. The size was set wrong for all
fragments but the first, affecting the transmission
of any skb with more than one fragment.

Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agoMerge branch 'ieee802154-for-davem-2018-02-26' of git://git.kernel.org/pub/scm/linux...
David S. Miller [Tue, 27 Feb 2018 16:14:57 +0000 (11:14 -0500)]
Merge branch 'ieee802154-for-davem-2018-02-26' of git://git./linux/kernel/git/sschmidt/wpan-next

Stefan Schmidt says:

====================
pull-request: ieee802154-next 2018-02-26

An update from ieee802154 for *net-next*

Alexander corrected a setting which got lost during some 6lowpan rework
a while back and Xue Liu provided us with a new driver for the MCR20A
transceiver.

If there are any issues let me know. If not, please pull.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agoMerge branch 'pernet_operations-convert-part-3'
David S. Miller [Tue, 27 Feb 2018 16:01:40 +0000 (11:01 -0500)]
Merge branch 'pernet_operations-convert-part-3'

Kirill Tkhai says:

====================
Converting pernet_operations (part #3)

This patchset continues to review and to convert pernet_operations
to async. Where it is possible, they are grouped by type of actions
init/exit methods ([1/28], for example). I hope this will make
the review a little bit easier. The changes are tree-wide: in net, fs,
drivers and security.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: Convert smack_net_ops
Kirill Tkhai [Mon, 26 Feb 2018 13:04:02 +0000 (16:04 +0300)]
net: Convert smack_net_ops

These pernet_operations only register and unregister nf hooks.
So, they are able to be marked as async.

Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: Convert selinux_net_ops
Kirill Tkhai [Mon, 26 Feb 2018 13:03:55 +0000 (16:03 +0300)]
net: Convert selinux_net_ops

These pernet_operations only register and unregister nf hooks.
So, they are able to be marked as async.

Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: Convert defrag6_net_ops
Kirill Tkhai [Mon, 26 Feb 2018 13:03:45 +0000 (16:03 +0300)]
net: Convert defrag6_net_ops

These pernet_operations only unregister nf hooks.
So, they are able to be marked as async.

Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: Convert ila_net_ops
Kirill Tkhai [Mon, 26 Feb 2018 13:03:36 +0000 (16:03 +0300)]
net: Convert ila_net_ops

These pernet_operations register and unregister nf hooks.
Also they populate and depopulate ila_net_id-pointed hash
table. The table is changed by hooks during skb processing
and via netlink request. It looks impossible for another
net pernet_operations to force the table reading or writing,
so, they are able to be marked as async.

Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: Convert defrag4_net_ops
Kirill Tkhai [Mon, 26 Feb 2018 13:03:15 +0000 (16:03 +0300)]
net: Convert defrag4_net_ops

These pernet_operations only unregister nf hooks.
So, they are able to be marked as async.

Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: Convert clusterip_net_ops
Kirill Tkhai [Mon, 26 Feb 2018 13:03:05 +0000 (16:03 +0300)]
net: Convert clusterip_net_ops

These pernet_operations register and unregister nf hooks,
and populate and destroy /proc entry. So, they are able
to be marked as async.

Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: Convert brnf_net_ops
Kirill Tkhai [Mon, 26 Feb 2018 13:02:56 +0000 (16:02 +0300)]
net: Convert brnf_net_ops

These pernet_operations only unregister nf hooks.
So, they are able to be marked as async.

Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: Convert ipvlan_net_ops
Kirill Tkhai [Mon, 26 Feb 2018 13:02:48 +0000 (16:02 +0300)]
net: Convert ipvlan_net_ops

These pernet_operations unregister ipvlan net hooks.
nf_unregister_net_hooks() removes hooks one-by-one,
and then frees the memory via rcu. This looks similar
to that happens, when a new hooks is added: allocation
of bigger memory region, copy of old content, and rcu
freeing the old memory. So, all of net code should be
well with this behavior. Also at the time of hook
unregistering, there are no packets, and foreign net
pernet_operations are not interested in others hooks.
So, we mark them as async.

Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: Convert cfg802154_pernet_ops
Kirill Tkhai [Mon, 26 Feb 2018 13:02:37 +0000 (16:02 +0300)]
net: Convert cfg802154_pernet_ops

These pernet_operations have only exit method, which
moves devices from cfg802154_rdev_list to init_net.
This may occur in any time from nl802154_wpan_phy_netns(),
so we are nice with rtnl_lock() synchronization.

Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: Convert sit_net_ops
Kirill Tkhai [Mon, 26 Feb 2018 13:02:27 +0000 (16:02 +0300)]
net: Convert sit_net_ops

These pernet_operations are similar to ip6_tnl_net_ops. Exit method
unregisters all net sit devices, and it looks like another
pernet_operations are not interested in foreign net sit list.
Init method registers netdevice. So, it's possible to mark them async.

Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: Convert vti6_net_ops
Kirill Tkhai [Mon, 26 Feb 2018 13:02:19 +0000 (16:02 +0300)]
net: Convert vti6_net_ops

These pernet_operations are similar to ip6_tnl_net_ops. Exit method
unregisters all net vti6 tunnels, and it looks like another
pernet_operations are not interested in foreign net vti6 list.
Init method registers netdevice. So, it's possible to mark them async.

Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: Convert ip6_tnl_net_ops
Kirill Tkhai [Mon, 26 Feb 2018 13:02:11 +0000 (16:02 +0300)]
net: Convert ip6_tnl_net_ops

These pernet_operations are similar to ip6gre_net_ops. Exit method
unregisters all net ip6_tnl tunnels, and it looks like another
pernet_operations are not interested in foreign net tunnels list.
So, it's possible to mark them async.

Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: Convert ip6gre_net_ops
Kirill Tkhai [Mon, 26 Feb 2018 13:02:03 +0000 (16:02 +0300)]
net: Convert ip6gre_net_ops

These pernet_operations are similar to bond_net_ops. Exit method
unregisters all net ip6gre devices, and it looks like another
pernet_operations are not interested in foreign net ip6gre list
or net_generic()->tunnels_wc. Init method registers net device.
So, it's possible to mark them async.

Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: Convert ipgre_net_ops, ipgre_tap_net_ops, erspan_net_ops, vti_net_ops and ipip_n...
Kirill Tkhai [Mon, 26 Feb 2018 13:01:52 +0000 (16:01 +0300)]
net: Convert ipgre_net_ops, ipgre_tap_net_ops, erspan_net_ops, vti_net_ops and ipip_net_ops

These pernet_operations are similar to bond_net_ops. Exit methods
unregisters all net ipgre/ipgre_tap/erspan/vti/ipip devices, and it
looks like another pernet_operations are not interested in foreign
net ipgre/ipgre_tap/erspan/vti/ipip list. Init method also does not
intersect with something pernet-specific. So, it's possible
to mark them async.

Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: Convert br_net_ops
Kirill Tkhai [Mon, 26 Feb 2018 13:01:43 +0000 (16:01 +0300)]
net: Convert br_net_ops

These pernet_operations are similar to bond_net_ops. Exit method
unregisters all net bridge devices, and it looks like another
pernet_operations are not interested in foreign net bridge list.
So, it's possible to mark them async.

Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: Convert vxlan_net_ops
Kirill Tkhai [Mon, 26 Feb 2018 13:01:34 +0000 (16:01 +0300)]
net: Convert vxlan_net_ops

These pernet_operations are similar to bond_net_ops. Exit method
unregisters all net vlanx devices, and it looks like another
pernet_operations are not interested in foreign net vlanx list.
So, it's possible to mark them async.

Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: Convert ppp_net_ops
Kirill Tkhai [Mon, 26 Feb 2018 13:01:25 +0000 (16:01 +0300)]
net: Convert ppp_net_ops

These pernet_operations are similar to bond_net_ops. Exit method
unregisters all net ppp devices, and it looks like another
pernet_operations are not interested in foreign net ppp list.
So, it's possible to mark them async.

Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: Convert gtp_net_ops
Kirill Tkhai [Mon, 26 Feb 2018 13:01:16 +0000 (16:01 +0300)]
net: Convert gtp_net_ops

These pernet_operations are similar to bond_net_ops. Exit method
unregisters all net gtp devices, and it looks like another
pernet_operations are not interested in foreign net gtp list.
So, it's possible to mark them async.

Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: Convert geneve_net_ops
Kirill Tkhai [Mon, 26 Feb 2018 13:00:48 +0000 (16:00 +0300)]
net: Convert geneve_net_ops

These pernet_operations are similar to bond_net_ops. Exit method
unregisters all net geneve devices, and it looks like another
pernet_operations are not interested in foreign net geneve list.
So, it's possible to mark them async.

Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: Convert bond_net_ops
Kirill Tkhai [Mon, 26 Feb 2018 13:00:40 +0000 (16:00 +0300)]
net: Convert bond_net_ops

These pernet_operations populate/depopulate /proc and /sys
entries. Exit method unregisters all net bond devices, and
it seems another pernet_operations are not interested in
foreign net bond list. So, it's possible to mark them async.

Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: Convert tc_action_net_init() and tc_action_net_exit() based pernet_operations
Kirill Tkhai [Mon, 26 Feb 2018 13:00:31 +0000 (16:00 +0300)]
net: Convert tc_action_net_init() and tc_action_net_exit() based pernet_operations

These pernet_operations are from net/sched directory, and they call only
tc_action_net_init() and tc_action_net_exit():

bpf_net_ops
connmark_net_ops
csum_net_ops
gact_net_ops
ife_net_ops
ipt_net_ops
xt_net_ops
mirred_net_ops
nat_net_ops
pedit_net_ops
police_net_ops
sample_net_ops
simp_net_ops
skbedit_net_ops
skbmod_net_ops
tunnel_key_net_ops
vlan_net_ops

1)tc_action_net_init() just allocates and initializes per-net memory.
2)There should not be in-flight packets at the time of tc_action_net_exit()
call, or another pernet_operations send packets to dying net (except
netlink). So, it seems they can be marked as async.

Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: Convert sysctl creating and destroying pernet_operations
Kirill Tkhai [Mon, 26 Feb 2018 13:00:22 +0000 (16:00 +0300)]
net: Convert sysctl creating and destroying pernet_operations

These pernet_operations create and destroy sysctl tables,
and they are able to be executed in parallel with any others:

ip_vs_lblc_ops
ip_vs_lblcr_ops

Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: Convert cma_pernet_operations
Kirill Tkhai [Mon, 26 Feb 2018 13:00:12 +0000 (16:00 +0300)]
net: Convert cma_pernet_operations

These pernet_operations just create and destroy IDR.
So, we mark them as async.

Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: Convert simple pernet_operations
Kirill Tkhai [Mon, 26 Feb 2018 12:59:56 +0000 (15:59 +0300)]
net: Convert simple pernet_operations

These pernet_operations make pretty simple actions
like variable initialization on init, debug checks
on exit, and so on, and they obviously are able
to be executed in parallel with any others:

vrf_net_ops
lockd_net_ops
grace_net_ops
xfrm6_tunnel_net_ops
kcm_net_ops
tcf_net_ops

Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: Convert nfs_net_ops
Kirill Tkhai [Mon, 26 Feb 2018 12:59:47 +0000 (15:59 +0300)]
net: Convert nfs_net_ops

These pernet_operations just create and destroy /proc entries
and net_generic()->cb_ident_idr IDR. So, we are able to mark
them async.

Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: Convert synproxy_net_ops
Kirill Tkhai [Mon, 26 Feb 2018 12:59:37 +0000 (15:59 +0300)]
net: Convert synproxy_net_ops

These pernet_operations create and destroy /proc entries
and allocate extents to template ct, which depend on global
nf_ct_ext_types[] array. So, we are able to mark them async.

Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: Convert hashlimit_net_ops and recent_net_ops
Kirill Tkhai [Mon, 26 Feb 2018 12:59:28 +0000 (15:59 +0300)]
net: Convert hashlimit_net_ops and recent_net_ops

These pernet_operations just create and destroy /proc entries.
Also, new /proc entries also may come after new nf rules
are added, but this is not possible, when net isn't alive.
So, they are safe to be marked as async.

Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: Convert /proc creating and destroying pernet_operations
Kirill Tkhai [Mon, 26 Feb 2018 12:59:19 +0000 (15:59 +0300)]
net: Convert /proc creating and destroying pernet_operations

These pernet_operations just create and destroy /proc entries,
and they can safely marked as async:

pppoe_net_ops
vlan_net_ops
canbcm_pernet_ops
kcm_net_ops
pfkey_net_ops
pppol2tp_net_ops
phonet_net_ops

Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agoipvlan: fix building with modular IPV6
Arnd Bergmann [Mon, 26 Feb 2018 09:41:30 +0000 (10:41 +0100)]
ipvlan: fix building with modular IPV6

We no longer depend on IPV6, but that now causes a link error with
CONFIG_IPV6=m and CONFIG_IPVLAN=y:

drivers/net/ipvlan/ipvlan_core.o: In function `ipvlan_queue_xmit':
ipvlan_core.c:(.text+0x1440): undefined reference to `ip6_route_output_flags'
drivers/net/ipvlan/ipvlan_core.o: In function `ipvlan_l3_rcv':
ipvlan_core.c:(.text+0x1818): undefined reference to `ip6_route_input_lookup'

This adds back the dependency on IPV6, with the option of building without
IPV6, but forcing IPVLAN to be a module when IPV6 is a module.

Fixes: 94333fac44d1 ("ipvlan: drop ipv6 dependency")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agoMerge branch '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next...
David S. Miller [Tue, 27 Feb 2018 01:58:25 +0000 (20:58 -0500)]
Merge branch '10GbE' of git://git./linux/kernel/git/jkirsher/next-queue

Jeff Kirsher says:

====================
10GbE Intel Wired LAN Driver Updates 2018-02-26

This series contains updates to ixgbe and ixgbevf only.

Colin Ian King cleans up redundant variable assignments.

Tonghao Zhang updates ixgbe to avoid writing to the hardware when the
redirection table has not changed.

Jake fixes the driver logic for checking and clearing receive timestamp
hangs so that when the PTP_RX_TIMESTAMP_IN_REGISTER flag is set, we no
longer need to check for receive timestamp hangs, which in turn will
stop the spurious log messages.

Emil updates ixgbevf with several features and improvements done in
other drivers, starting with the handling of page addresses so that we
always refer to them using a void pointer.  Added a 'legacy-rx' flag to
allow switching between the old and new receive code paths.  Added
support for using 3K buggers in order 1 page.  Updated the driver to
ensure that calls to ixgbevf_open() are rtnl lock protected and improved
the error handling when setting up multiple queues.  Added support for
providing a buffer with head room and tail room to allow for shared
info, NET_SKB_PAD, and NET_IP_ALIGN, so that we can start using
build_skb to build frames instead of using memcpy() the headers.
Updated the logic of handling rings closer to ixgbe.  Consolidated the
receive paths to reduce duplication when we expand them in the future.
Added build_skb() support to ixgbevf.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agoi40e: remove some stray indenting
Dan Carpenter [Wed, 21 Feb 2018 12:53:53 +0000 (15:53 +0300)]
i40e: remove some stray indenting

These two lines are indented too far.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
6 years agoi40evf: remove redundant array comparisons to 0 checks
Colin Ian King [Mon, 19 Feb 2018 10:23:30 +0000 (10:23 +0000)]
i40evf: remove redundant array comparisons to 0 checks

The checks to see if key->dst.s6_addr and key->src.s6_addr are null
pointers are redundant because these are constant size arrays and
so the checks always return true.  Fix this by removing the redundant
checks.   Also replace filter->f with vf, allowing wide lines to be
condensed and to rejoin some split wide lines.

Detected by CoverityScan, CID#1465279 ("Array compared to 0")

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
6 years agoi40e: check that pointer VSI is not null before dereferencing it
Colin Ian King [Thu, 15 Feb 2018 19:50:52 +0000 (19:50 +0000)]
i40e: check that pointer VSI is not null before dereferencing it

Function i40e_find_vsi_from_id can potentially return null, hence
VSI may be null, so defensively check it is non-null before
dereferencing it to check the seid.

Fixes: e284fc280473 ("i40e: Add and delete cloud filter")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
6 years agoi40evf: pass struct virtchnl_filter by reference rather than by value
Colin Ian King [Thu, 15 Feb 2018 19:26:05 +0000 (19:26 +0000)]
i40evf: pass struct virtchnl_filter by reference rather than by value

Passing struct virtchnl_filter f by value requires a 272 byte copy
on x86_64, so instead pass it by reference is much more efficient. Also
adjust some lines that are over 80 chars.

Detected by CoverityScan, CID#1465285 ("Big parameter passed by value")

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
6 years agoi40e/i40evf: use SW variables for hang detection
Alan Brady [Mon, 12 Feb 2018 14:16:59 +0000 (09:16 -0500)]
i40e/i40evf: use SW variables for hang detection

The i40e_detect_recover_hung function uses the i40e_get_tx_pending
function to determine if there are packets stalled on the ring.
i40e_get_tx_pending calculates the pending packets using the head
writeback value and HW tail.  If the queue is stopped and we lose the
interrupt to update our next_to_clean then we a) won't get another
interrupt to clean because queue is stopped b) we won't catch the
problem with i40e_detect_recover_hung because the HW values look like
there's no packets waiting to be transmitted.  Using the SW values we
can catch the issue because next_to_clean will be out of sync with head
writeback.

This has the added benefit being less CPU intensive because we don't
need to reach into the hardware to get the values.

Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
6 years agoi40evf: Fix double locking the same resource
Paweł Jabłoński [Mon, 5 Feb 2018 21:03:36 +0000 (13:03 -0800)]
i40evf: Fix double locking the same resource

Removes the locking of adapter->mac_vlan_list_lock resource in
i40evf_add_filter(). The locking part is moved above i40evf_add_filter().
i40evf_add_filter(), called by i40evf_addr_sync(), was trying to lock the
resource again and double locking generated a kernel panic after bringing
an interface up.

Fixes: 8946b56354b7 ("i40evf: use __dev_[um]c_sync routines in
       .set_rx_mode")
Signed-off-by: Paweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
6 years agonet: make kmem caches as __ro_after_init
Alexey Dobriyan [Sat, 24 Feb 2018 18:20:33 +0000 (21:20 +0300)]
net: make kmem caches as __ro_after_init

All kmem caches aren't reallocated once set up.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agoi40e: link_down_on_close private flag support
Mariusz Stachura [Tue, 14 Nov 2017 12:00:50 +0000 (07:00 -0500)]
i40e: link_down_on_close private flag support

This patch introduces new ethtool private flag used for
forcing true link state. Function i40e_force_link_state that implements
this functionality was added, it sets phy_type = 0 in order to
work-around firmware's LESM. False positive error messages were
suppressed.

The ndo_open() should not succeed if there were issues with forcing link
state to be UP.

Added I40E_PHY_TYPES_BITMASK define with all phy types OR-ed together in
one bitmask.  Added after phy type definition, so it will be hard to
forget to include new phy types to the bitmask.

Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
6 years agoMerge branch 'sonic-ethernet-cleanups'
David S. Miller [Mon, 26 Feb 2018 19:40:03 +0000 (14:40 -0500)]
Merge branch 'sonic-ethernet-cleanups'

Finn Thain says:

====================
Fixes, cleanup and modernization for SONIC ethernet drivers

Changes since v4 of combined patch series:
- Removed redundant and non-portable MACH_IS_MAC tests.
- Omitted patches unrelated to SONIC drivers.
- Dropped changes to the 'version_printed' logic and debug message text.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet/sonic: Replace custom debug logging with netif_* calls
Finn Thain [Sat, 24 Feb 2018 23:27:25 +0000 (18:27 -0500)]
net/sonic: Replace custom debug logging with netif_* calls

Eliminate duplicated debug code by moving it into the core driver.
Don't log the only valid silicon revision number (it's in the source).

Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Chris Zankel <chris@zankel.net>
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet/sonic: Clean up and modernize log messages
Finn Thain [Sat, 24 Feb 2018 23:27:25 +0000 (18:27 -0500)]
net/sonic: Clean up and modernize log messages

Add missing printk severity levels by adopting pr_foo() calls for the
platform_driver and dev_foo() calls for the nubus_driver.
Avoid KERN_CONT usage as per advice from checkpatch.
Avoid #ifdef around printk calls.
Don't log driver probe messages after calling register_netdev().

Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Chris Zankel <chris@zankel.net>
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet/macsonic: Drop redundant MACH_IS_MAC test
Finn Thain [Sat, 24 Feb 2018 23:27:25 +0000 (18:27 -0500)]
net/macsonic: Drop redundant MACH_IS_MAC test

The MACH_IS_MAC test is redundant here because the platform device
won't get registered unless MACH_IS_MAC.

Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet/macsonic: Convert to nubus_driver
Finn Thain [Sat, 24 Feb 2018 23:27:25 +0000 (18:27 -0500)]
net/macsonic: Convert to nubus_driver

This resolves an old issue preventing any NuBus SONIC NICs from
working in a Mac with an on-board SONIC device.

Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agosh_eth: fix TSU init on SH7734/R8A7740
Sergei Shtylyov [Sat, 24 Feb 2018 19:41:45 +0000 (22:41 +0300)]
sh_eth: fix TSU init on SH7734/R8A7740

It appears that the single port Ether controllers having TSU (like SH7734/
R8A7740) need the same kind of treating in sh_eth_tsu_init() as R7S72100
currently has -- they also don't have the TSU registers related e.g. to
passing the frames between ports. Add the 'sh_eth_cpu_data::dual_port'
flag and use it as a new criterion for taking a "short path" in the TSU
init sequence in order to avoid writing to the non-existent registers...

Fixes: f0e81fecd4f8 ("net: sh_eth: Add support SH7734")
Fixes: 73a0d907301e ("net: sh_eth: add support R8A7740")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agosh_eth: TSU_QTAG0/1 registers the same as TSU_QTAGM0/1
Sergei Shtylyov [Sat, 24 Feb 2018 17:28:16 +0000 (20:28 +0300)]
sh_eth: TSU_QTAG0/1 registers the same as TSU_QTAGM0/1

The TSU_QTAG0/1 registers found in the Gigabit Ether controllers actually
have the same long name  as the TSU_QTAGM0/1 registers in the early Ether
controllers:  Qtag Addition/Deletion Set Register (Port 0/1 to 1/0); thus
there's no need to make a difference in sh_eth_tsu_init() between those
controllers. Unfortunately, we can't just remove TSU_QTAG0/1 from the
register *enum* because that would break the ethtool register dump...

Fixes: b0ca2a21f769 ("sh_eth: Add support of SH7763 to sh_eth")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agotc: python3, string formattings
BTaskaya [Fri, 23 Feb 2018 19:57:35 +0000 (22:57 +0300)]
tc: python3, string formattings

This patch converts old type string formattings to new type string
formattings for adapting Linux Traffic Control (tc) unit testing suite
python3.

Linux Traffic Control (tc) unit testing suite's code quality improved is improved with this patch.
According to python documentation;
"The built-in string class provides the ability to do complex variable substitutions and
value formatting via the format() method described in PEP 3101. "
but the project was using old type formattings and new type string formattings together,
this patch's main purpose is converting all old types to new types.

Following files changed:
 1. tools/testing/selftests/tc-testing/tdc.py
 2. tools/testing/selftests/tc-testing/tdc_batch.py

Following PEP rules applied:
 1. PEP8 - Code Styling
 2. PEP3101 - Advanced Code Formatting

Signed-off-by: Batuhan Osman Taskaya <batuhanosmantaskaya@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agoixgbevf: remove redundant initialization of variable 'dma'
Colin Ian King [Thu, 1 Feb 2018 18:35:39 +0000 (18:35 +0000)]
ixgbevf: remove redundant initialization of variable 'dma'

Variable dma is initialized with a value that is never read, later
on it is re-assigned a new value, hence the initialization is redundant
and can be removed.

Cleans up clang warning:
drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c:584:13: warning: Value
stored to 'dma' during its initialization is never read

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
6 years agoixgbevf: add build_skb support
Emil Tantilov [Wed, 31 Jan 2018 00:51:54 +0000 (16:51 -0800)]
ixgbevf: add build_skb support

Add support for build_skb() similar to:
commit 6f429223b31c ("ixgbe: Add support for build_skb")

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
6 years agoixgbevf: break out Rx buffer page management
Emil Tantilov [Wed, 31 Jan 2018 00:51:49 +0000 (16:51 -0800)]
ixgbevf: break out Rx buffer page management

Based on commit e014272672b9 ("igb: Break out Rx buffer page management")

Consolidate Rx code paths to reduce duplication when we expand them in
the future.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
6 years agoixgbevf: allocate the rings as part of q_vector
Emil Tantilov [Wed, 31 Jan 2018 00:51:43 +0000 (16:51 -0800)]
ixgbevf: allocate the rings as part of q_vector

Make it so that all rings allocations are made as part of q_vector.
The advantage to this is that we can keep all of the memory related to
a single interrupt in one page.

The goal is to bring the logic of handling rings closer to ixgbe.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
6 years agoixgbevf: make sure all frames fit minimum size requirements
Emil Tantilov [Wed, 31 Jan 2018 00:51:38 +0000 (16:51 -0800)]
ixgbevf: make sure all frames fit minimum size requirements

Similar to commit a50c29dd09ed
("ixgbe: Make certain that all frames fit minimum size requirements")

Make sure that any packet we attempt to transmit will meet minimum
size requirements.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
6 years agoixgbevf: add support for padding packet
Emil Tantilov [Wed, 31 Jan 2018 00:51:33 +0000 (16:51 -0800)]
ixgbevf: add support for padding packet

Following the logic from commit 2de6aa3a666e
("ixgbe: Add support for padding packet")

Add support for providing a buffer with headroom and tail room
to allow for shared info, NET_SKB_PAD, and NET_IP_ALIGN.  With this
combined with the DMA changes we can start using build_skb to build frames
around an incoming Rx buffer instead of having to memcpy the headers.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
6 years agoixgbevf: setup queue counts
Emil Tantilov [Wed, 31 Jan 2018 00:51:27 +0000 (16:51 -0800)]
ixgbevf: setup queue counts

Add calls for netif_set_real_num_t/rx_queues() in ixgbevf_open().
Make sure that calls to ixgbevf_open() are rtnl protected and improve
the error handling when setting up multiple queues.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
6 years agoixgbevf: add support for using order 1 pages to receive large frames
Emil Tantilov [Wed, 31 Jan 2018 00:51:22 +0000 (16:51 -0800)]
ixgbevf: add support for using order 1 pages to receive large frames

Based on commit 8649aaef4044
("igb: Add support for using order 1 pages to receive large frames")

Add support for using 3K buffers in order 1 page. We are reserving 1K for
now to have space available for future tail room and head room when we
enable build_skb support.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
6 years agoixgbevf: add ethtool private flag for legacy Rx
Emil Tantilov [Wed, 31 Jan 2018 00:51:17 +0000 (16:51 -0800)]
ixgbevf: add ethtool private flag for legacy Rx

Introduce legacy-rx private flag that will allow switching between the
old and new (build_skb based) Rx code paths. The implementation is the
same as in commit e08912985b29
("igb: Add support for ethtool private flag to allow use of legacy Rx")

This provides a means of validating the legacy Rx path in the event that
we are forced to fall back.  At some point in the future when we are
convinced we don't need it anymore we might be able to drop the legacy-rx
flag.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
6 years agoixgbevf: use page_address offset from page
Emil Tantilov [Wed, 31 Jan 2018 00:51:12 +0000 (16:51 -0800)]
ixgbevf: use page_address offset from page

Based on commit 3456fd53421e
("igb: Use page_address offset from page instead of masking virtual address")

Update the handling of page addresses so that we always refer to them using
a void pointer, and try to use the consistent name of va indicating we are
working with a virtual address.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
6 years agoixgbe: prevent ptp_rx_hang from running when in FILTER_ALL mode
Jacob Keller [Mon, 29 Jan 2018 23:57:48 +0000 (15:57 -0800)]
ixgbe: prevent ptp_rx_hang from running when in FILTER_ALL mode

On hardware which supports timestamping all packets, the timestamps are
recorded in the packet buffer, and the driver no longer uses or reads
the registers. This makes the logic for checking and clearing Rx
timestamp hangs meaningless.

If we run the ixgbe_ptp_rx_hang() function in this case, then the driver
will continuously spam the log output with "Clearing Rx timestamp hang".
These messages are spurious, and confusing to end users.

The original code in commit a9763f3cb54c ("ixgbe: Update PTP to support
X550EM_x devices", 2015-12-03) did have a flag PTP_RX_TIMESTAMP_IN_REGISTER
which was intended to be used to avoid the Rx timestamp hang check,
however it did not actually check the flag before calling the function.

Do so now in order to stop the checks and prevent the spurious log
messages.

Fixes: a9763f3cb54c ("ixgbe: Update PTP to support X550EM_x devices", 2015-12-03)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
6 years agoixgbe: Avoid to write the RETA table when unnecessary
Tonghao Zhang [Sun, 28 Jan 2018 11:53:37 +0000 (03:53 -0800)]
ixgbe: Avoid to write the RETA table when unnecessary

If indir == 0 in the ixgbe_set_rxfh(), it is unnecessary
to write the HW. Because redirection table is not changed.

Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
6 years agoxen-netback: make function xenvif_rx_skb static
Colin Ian King [Fri, 23 Feb 2018 17:16:57 +0000 (17:16 +0000)]
xen-netback: make function xenvif_rx_skb static

The function xenvif_rx_skb is local to the source and does not need
to be in global scope, so make it static.

Cleans up sparse warning:
drivers/net/xen-netback/rx.c:422:6: warning: symbol 'xenvif_rx_skb'
was not declared. Should it be static?

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agoMerge branch 'tools-tc-testing-better-error-reporting'
David S. Miller [Mon, 26 Feb 2018 16:36:11 +0000 (11:36 -0500)]
Merge branch 'tools-tc-testing-better-error-reporting'

Brenda J. Butler says:

====================
tools: tc-testing: better error reporting

This patch set contains a bit of cleanup and better error reporting,
esp. in pre- and post-suite, and pre- and post-case commands.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agotools: tc-testing: better error reporting
Brenda J. Butler [Fri, 23 Feb 2018 17:16:38 +0000 (12:16 -0500)]
tools: tc-testing: better error reporting

Do a better job with error handling - in pre- and post-suite,
in pre- and post-case.  Show a traceback for errors.

Signed-off-by: Brenda J. Butler <bjb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agotools: tc-testing: Fix indentation
Brenda J. Butler [Fri, 23 Feb 2018 17:16:37 +0000 (12:16 -0500)]
tools: tc-testing: Fix indentation

Signed-off-by: Brenda J. Butler <bjb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agosfc: falcon: remove duplicated bit-wise or of LOOPBACK_SGMII
Colin Ian King [Fri, 23 Feb 2018 14:00:56 +0000 (14:00 +0000)]
sfc: falcon: remove duplicated bit-wise or of LOOPBACK_SGMII

Bit pattern LOOPBACK_SGMII is being bit-wise or'd twice; remove the
redundant 2nd LOOPBACK_SGMII

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agomlxsw: spectrum_kvdl: avoid uninitialized variable warning
Arnd Bergmann [Fri, 23 Feb 2018 13:15:32 +0000 (14:15 +0100)]
mlxsw: spectrum_kvdl: avoid uninitialized variable warning

gcc warns that 'resource_id' is not initialized if we don't come though
any of the three 'case' statements before:

drivers/net/ethernet/mellanox/mlxsw/spectrum_kvdl.c: In function 'mlxsw_sp_kvdl_part_init':
drivers/net/ethernet/mellanox/mlxsw/spectrum_kvdl.c:275:8: error: 'resource_id' may be used uninitialized in this function [-Werror=maybe-uninitialized]

In the current code, that won't happen, but it's more robust to explicitly
handle this by returning a failure from mlxsw_sp_kvdl_part_init.

Fixes: 887839e6960d ("mlxsw: spectrum_kvdl: Add support for dynamic partition set")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agomlxsw: spectrum_kvdl: use div_u64() for 64-bit division
Arnd Bergmann [Fri, 23 Feb 2018 13:15:31 +0000 (14:15 +0100)]
mlxsw: spectrum_kvdl: use div_u64() for 64-bit division

Calculating the number of entries now uses 64-bit arithmetic that
causes a link error on 32-bit architectures:

drivers/net/ethernet/mellanox/mlxsw/spectrum_kvdl.o: In function `mlxsw_sp_kvdl_init':
spectrum_kvdl.c:(.text+0x51c): undefined reference to `__aeabi_uldivmod'

We could probably use a 32-bit division here as before, but since this is
not in a performance critical path, div_u64() seems cleaner here.

Fixes: 887839e6960d ("mlxsw: spectrum_kvdl: Add support for dynamic partition set")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agoixgbe: remove redundant initialization of 'pool'
Colin Ian King [Tue, 16 Jan 2018 12:48:09 +0000 (12:48 +0000)]
ixgbe: remove redundant initialization of 'pool'

Variable pool is being assigned zero and then in the following for-loop
is it being set to zero again. Remove the redundant first assignment.

Cleans up clang warning:
drivers/net/ethernet/intel/ixgbe/ixgbe_lib.c:61:2: warning: Value stored
to 'pool' is never read

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
6 years agoMerge branch 'mv88e6xxx-Poll-when-no-interrupt-defined'
David S. Miller [Mon, 26 Feb 2018 16:28:11 +0000 (11:28 -0500)]
Merge branch 'mv88e6xxx-Poll-when-no-interrupt-defined'

Andrew Lunn says:

====================
mv88e6xxx: Poll when no interrupt defined

Not all boards using the mv88e6xxx switches have the interrupt output
connected to a GPIO. On these boards phylib has to poll the PHYs,
rather than use interrupts. Have the driver poll the interrupt status
register, which is more efficient than having phylib do it. And it
enables other switch interrupts to be services.

The Armada 370RD is such a board without a interrupt GPIO. Now that
interrupts work, wire up the PHYs to make use if them.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agoarm: mvebu: 370-rd: Enable PHY interrupt handling
Andrew Lunn [Thu, 22 Feb 2018 21:58:33 +0000 (22:58 +0100)]
arm: mvebu: 370-rd: Enable PHY interrupt handling

The Ethernet switch has an embedded interrupt controller. Interrupts
from the embedded PHYs are part of this interrupt controller.
Explicitly list the MDIO bus the embedded PHYs are on, and wire up the
interrupts.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agonet: dsa: mv88e6xxx: Poll when no interrupt defined
Andrew Lunn [Thu, 22 Feb 2018 21:58:32 +0000 (22:58 +0100)]
net: dsa: mv88e6xxx: Poll when no interrupt defined

Not all boards have the interrupt output from the switch connected to
a GPIO line. In such cases, phylib has to poll the internal PHYs,
rather than receive an interrupt when there is a change in the link
state. phylib polls once per second, and per PHY reads around 4
words. With a switch typically having 4 internal PHYs, this means 16
MDIO transactions per second.

Rather than performing this phylib level polling, have the driver poll
the interrupt status register. If the status register indicates an
interrupt condition processing of interrupts in the same way as if a
GPIO was used.

Polling 10 times a second places less load on the MDIO bus. But rather
than taking on average 0.5s to detect a link change, it takes less
than 0.05s. Additionally, other interrupts, such as the watchdog, ATU
and VTU violations will be reported.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agomlxsw: spectrum_switchdev: Allow port enslavement to a VLAN-unaware bridge
Ido Schimmel [Tue, 20 Feb 2018 07:45:12 +0000 (08:45 +0100)]
mlxsw: spectrum_switchdev: Allow port enslavement to a VLAN-unaware bridge

Up until now we only allowed VLAN devices to be put in a VLAN-unaware
bridge, but some users need the ability to enslave physical ports as
well.

This is achieved by mapping the port and VID 1 to the bridge's vFID,
instead of the port and the VID used by the VLAN device.

The above is valid because as long as the port is not enslaved to a
bridge, VID 1 is guaranteed to be configured as PVID and egress
untagged.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
David S. Miller [Mon, 26 Feb 2018 15:37:24 +0000 (10:37 -0500)]
Merge git://git./linux/kernel/git/bpf/bpf-next

Daniel Borkmann says:

====================
pull-request: bpf-next 2018-02-26

The following pull-request contains BPF updates for your *net-next* tree.

The main changes are:

1) Various improvements for BPF kselftests: i) skip unprivileged tests
   when kernel.unprivileged_bpf_disabled sysctl knob is set, ii) count
   the number of skipped tests from unprivileged, iii) when a test case
   had an unexpected error then print the actual but also the unexpected
   one for better comparison, from Joe.

2) Add a sample program for collecting CPU state statistics with regards
   to how long the CPU resides in cstate and pstate levels. Based on
   cpu_idle and cpu_frequency trace points, from Leo.

3) Various x64 BPF JIT optimizations to further shrink the generated
   image size in order to make it more icache friendly. When tested on
   the Cilium generated programs, image size reduced by approx 4-5% in
   best case mainly due to how LLVM emits unsigned 32 bit constants,
   from Daniel.

4) Improvements and fixes on the BPF sockmap sample programs: i) fix
   the sockmap's Makefile to include nlattr.o for libbpf, ii) detach
   the sock ops programs from the cgroup before exit, from Prashant.

5) Avoid including xdp.h in filter.h by just forward declaring the
   struct xdp_rxq_info in filter.h, from Jesper.

6) Fix the BPF kselftests Makefile for cgroup_helpers.c by only declaring
   it a dependency for test_dev_cgroup.c but not every other test case
   where it is not needed, from Jesper.

7) Adjust rlimit RLIMIT_MEMLOCK for test_tcpbpf_user selftest since the
   default is insufficient for creating the 'global_map' used in the
   corresponding BPF program, from Yonghong.

8) Likewise, for the xdp_redirect sample, Tushar ran into the same when
   invoking xdp_redirect and xdp_monitor at the same time, therefore
   in order to have the sample generically work bump the limit here,
   too. Fix from Tushar.

9) Avoid an unnecessary NULL check in BPF_CGROUP_RUN_PROG_INET_SOCK()
   since sk is always guaranteed to be non-NULL, from Yafang.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
6 years agosamples/bpf: Add program for CPU state statistics
Leo Yan [Mon, 26 Feb 2018 01:19:12 +0000 (09:19 +0800)]
samples/bpf: Add program for CPU state statistics

CPU is active when have running tasks on it and CPUFreq governor can
select different operating points (OPP) according to different workload;
we use 'pstate' to present CPU state which have running tasks with one
specific OPP.  On the other hand, CPU is idle which only idle task on
it, CPUIdle governor can select one specific idle state to power off
hardware logics; we use 'cstate' to present CPU idle state.

Based on trace events 'cpu_idle' and 'cpu_frequency' we can accomplish
the duration statistics for every state.  Every time when CPU enters
into or exits from idle states, the trace event 'cpu_idle' is recorded;
trace event 'cpu_frequency' records the event for CPU OPP changing, so
it's easily to know how long time the CPU stays in the specified OPP,
and the CPU must be not in any idle state.

This patch is to utilize the mentioned trace events for pstate and
cstate statistics.  To achieve more accurate profiling data, the program
uses below sequence to insure CPU running/idle time aren't missed:

- Before profiling the user space program wakes up all CPUs for once, so
  can avoid to missing account time for CPU staying in idle state for
  long time; the program forces to set 'scaling_max_freq' to lowest
  frequency and then restore 'scaling_max_freq' to highest frequency,
  this can ensure the frequency to be set to lowest frequency and later
  after start to run workload the frequency can be easily to be changed
  to higher frequency;

- User space program reads map data and update statistics for every 5s,
  so this is same with other sample bpf programs for avoiding big
  overload introduced by bpf program self;

- When send signal to terminate program, the signal handler wakes up
  all CPUs, set lowest frequency and restore highest frequency to
  'scaling_max_freq'; this is exactly same with the first step so
  avoid to missing account CPU pstate and cstate time during last
  stage.  Finally it reports the latest statistics.

The program has been tested on Hikey board with octa CA53 CPUs, below
is one example for statistics result, the format mainly follows up
Jesper Dangaard Brouer suggestion.

Jesper reminds to 'get printf to pretty print with thousands separators
use %' and setlocale(LC_NUMERIC, "en_US")', tried three different arm64
GCC toolchains (5.4.0 20160609, 6.2.1 20161016, 6.3.0 20170516) but all
of them cannot support printf flag character %' on arm64 platform, so go
back print number without grouping mode.

CPU states statistics:
state(ms)  cstate-0    cstate-1    cstate-2    pstate-0    pstate-1    pstate-2    pstate-3    pstate-4
CPU-0      767         6111        111863      561         31          756         853         190
CPU-1      241         10606       107956      484         125         646         990         85
CPU-2      413         19721       98735       636         84          696         757         89
CPU-3      84          11711       79989       17516       909         4811        5773        341
CPU-4      152         19610       98229       444         53          649         708         1283
CPU-5      185         8781        108697      666         91          671         677         1365
CPU-6      157         21964       95825       581         67          566         684         1284
CPU-7      125         15238       102704      398         20          665         786         1197

Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
6 years agoMerge branch 'x86-jit'
Alexei Starovoitov [Sat, 24 Feb 2018 06:50:41 +0000 (22:50 -0800)]
Merge branch 'x86-jit'

Daniel Borkmann says:

====================
Couple of minor improvements to the x64 JIT I had still around from
pre merge window in order to shrink the image size further. Added
test cases for kselftests too as well as running Cilium workloads on
them w/o issues.
====================

Signed-off-by: Alexei Starovoitov <ast@kernel.org>