rt2x00: Add RF chip definition

Add RF chip definition

Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Implement get_survey callback for rt2800

Implement the get_survey callback to allow user space to read statistics
about the current channel condition.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Add rt2800 EEPROM definition

Add and modify NIC Configuration and LED definition of EEPROM

Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: update AR9003 initvals to improve carrier leak calibration/correction

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: update AR9003 initvals for improved radar detection

Reduces the likelihood of false pulse detects in the hardware

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: fix PA predistortion training power selection

The EEPROM contains scale factors for the tx power, which define
the range of allowable difference between target power and training
power. If the difference is too big, PA predistortion cannot be used.
For 2.4 GHz there is only one scale factor, for 5 GHz there are
three, depending on the specific frequency range.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: fix the PA predistortion rate mask

The EEPROM PAPRD rate mask fields only contain mask values for actual
rates in the low 25 bits. The upper bits are reserved for tx power
scale values. Add the proper mask definitions and use them before
writing the values to the register.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix PA predistortion thermal measurement handling

To be able to measure the thermal values correctly for PAPRD, we need
to send training frames before setting up the gain table for the measurement,
and then again afterwards for the actual training.

For further improvement, send training frames at MCS0 instead of 54 MBit/s
legacy. That way we can use the No-ACK flag for the transmission, which
speeds up PAPRD training in general, as the hardware won't have to
retransmit and wait for ACK timeout (was previously set to 4 * 6
transmission attempts).

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: fix the slot time setting for long distance links

Testing shows that adjusting the slot time based on the coverage class
produces very high latencies and very low throughput on long distance links.

Adjusting only the ACK timeout and leaving the slot time at the regular
values - while technically not optimal for CSMA - works a lot better on
long links (tested with 10 km distance)

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: initialize ah->slottime

(u32) -1 is not particularly useful as a slottime default, so even though
the ath9k_hw default should never get used, it's better to pick something
sane here.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Add Ubiquiti wifistation ext to supported devices

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: remove ah->txpower_indexoffset

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: remove ah->beacon_interval

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: clean up SREV version checks

There's no need to have separate callbacks for pre-AR9003 vs AR9003
SREV version checks, so just merge those into one function.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: remove antenna configuration eeprom ops and variables

AR9280 based hardware with 3 antennas and slow antenna diversity has
not been seen in the wild and ath9k does not support that form of
antenna diversity, so remove the EEPROM ops for it.
These EEPROM ops are currently only used for setting the
AR_PHY_SWITCH_COM register, which is being done in the EEPROM specific
file already.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: merge the ar9287 version of ath9k_hw_get_gain_boundaries_pdadcs

Also add a comment about a potential array overrun that needs to
be reviewed.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: merge ath9k_hw_get_gain_boundaries_pdadcs between eeprom_def.c and eeprom_4k.c

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: clean up duplicate and unnused eeprom related defines

AR*_MAX_RATE_POWER => MAX_RATE_POWER
AR*_EEPROM_MODAL_SPURS => AR_EEPROM_MODAL_SPURS
AR*_OPFLAGS_* => AR5416_OPFLAGS_*
...

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: only use the PCIe disable register write sequence for AR5416

Newer chips do not need this, and maybe these register writes could have
negative side effects on newer hardware.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix sequence number assigment for non-AMPDU QoS data frames

wireless-testing commit 04caf863750bc7e042d1e8d57e5ce9d6326ab435
('ath9k: more tx setup cleanups') merged tx path code for HT vs
non-HT frames, however it did not pass the tid pointer to
ath_tx_send_normal, causing an inconsistency between AMPDU vs
non-AMPDU sequence number handling.
Fix this by always passing in the tid pointer for all QoS data frames.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: support IBSS RSN with SW crypto

When software crypto is used, mac80211 will
support IBSS RSN, it doesn't depend on the
driver in that case.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Use power save wrappers for TSF get/set

The HW has to be awake when accessing registers.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ieee80211: add Parameter Set Count bitmask

WMM IE QoS Info field lower 4 bits: Parameter Set Count

Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211 default tx_last_beacon false (congestion)

The 802.11 spec states that the STA that generated the last Beacon frame shall
be the STA that response to a probe request.  This is important for congestion
reduction when a probe request is received - only 1 node in an adhoc BSS
will transmit a response.  While mac80211 drivers should provide the
tx_last_beacon function to report if they transmitted the last beacon many
do not.  As an attempt to reduce probe response congestion default this
to 0 such that a node not implementing this capability does not contribute
to unnecessary congestion.

In a modern medium sized office environment I see upwards of 100 probe
requests per second received at a given node from various hardware/OS/drivers
doing zeroconf 'active probing' as opposed to passively listening for beacons.
With a modest 10-node adhoc network consisting of drivers that do not implement
this tx_last_beacon feature, I have seen this result in the simultaneous xmit
of probe responses accumulating to 500 probe responses per second because of
collisions which brings the adhoc network to its knees as well as causes
needless congestion.

Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: rename TMS defines, drop useless condition from core reset

As discussed we do not know band width at core reset time and it is not a good
idea to reset whole just to change band. So just set unconditionally 20 MHz
band width as default during core reset.

As for defines PHY clock changed to band width in specs and it makes much more
sens to call defines by band width which is self-explainable. Updated specs do
not mention 0 value, but comparing to old ones you can notice lineral relation
between PHY clock speed and band width. So it makes sense for 0x0 value to be
10 MHz band width.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: use designed function and macro for writing tables

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: one more fix for order of tables initialization

I missed that part in previous reordering.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: use correct bit for controlling MAC and PHY

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: support separate default keys

Add support for split default keys (unicast
and multicast) in mac80211.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211/nl80211: separate unicast/multicast default TX keys

Allow userspace to specify that a given key
is default only for unicast and/or multicast
transmissions. Only WEP keys are for both,
WPA/RSN keys set here are GTKs for multicast
only. For more future flexibility, allow to
specify all combiations.

Wireless extensions can only set both so use
nl80211; WEP keys (connect keys) must be set
as default for both (but 802.1X WEP is still
possible).

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: clean up RX key checks

Using the default key for "any key set" isn't
quite what we should do. It works, but with the
upcoming changes it makes life unnecessarily
complex, so do something better here and really
check for "any key".

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: clean up hardware code for beacon handling

The registers TBTT_TIMER ,DMA_BEACON_ALERT ,NEXT_SWBA are need to be
configured only for AP and IBSS mode.

SWBA register is used for generating software interrupts so that beacon
frames will be created by the software.DMA beacon alert register is
to indicate the hardware to DMA the contents of beacon buffer to PCU buffer
and TBTT to start transmitting the packet buffer to the base band.
Clearly these things are not needed for station/monitor mode so
remove configuring them.

Cc: doug dahlby <ddahlby@atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: update information elements in cached BSS struct

When a cached BSS struct is updated because a new beacon was received,
the code replaces the cached information elements by the IEs from the
new beacon. However it did not update the pub.information_elements
and pub.len_information_elements fields leaving them either pointing
to the old beacon IEs or in an inconsistent state where the data is
replaced by the new beacon IEs but len_information_elements still has
its value from the first beacon.

Fix this by updating the information elements fields if they are
pointing to beacon IEs.

Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath: Missed to clear key4 of micentry

key4 of micentry is used, if ATH_CRYPT_CAP_MIC_COMBINED is set.
But is not cleared on key cache reset.

Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Add change_interface callback

Add support to change interface type
without bringing down the interface.

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: Add antenna availability information

Add a field to wiphy for the hardware to report the availble antennas for
configuration. Only if this is set to something bigger than zero, will the
anntenna configuration ops be executed.

Allthough this could be a simple number of antennas, I defined it as a bitmap
of antennas which are available for configuration, since it's more consistent
with the rest of the antenna API and there could be cases where the
hardware allows only configuration of certain antennas. As it does not make
much of a difference in size or normal usage, I think it's better to be able to
support this, in case the need arises.

The antenna configuration is now also checked against the availabe antennas and
rejected if it does not match.

Signed-off-by: Bruno Randolf <br1@einfach.org>
--
v3: always apply available antenna mask (for "all" antennas case).

v2: reject antenna configurations which don't match the available antennas
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix assumptions for idle calls on suspend/resume

mac80211 will notify drivers when to go idle and ath9k
assumed that it would get further notifications for idle
states after a device stop() config call but as per agreed
semantics the idle state of the radio is left up to driver
after mac80211 issues the stop() callback. The driver is
resposnbile for ensuring the device remains idle after
that even between suspend / resume calls.

This fixes suspend/resume when you issue suspend and resume
twice on ath9k when ath9k_stop() was already called. We need
to put the radio to full sleep in order for resume to work
correctly.

What might seem fishy is we are turning the radio off
after resume. The reason why we do this is because we know
we should not have anything enabled after a mac80211 tells
us to stop(), if we resume and never get a start() we won't
get another stop() by mac80211 so to be safe always bring
the 802.11 device with the radio disabled after resume,
this ensures that if we suspend we already have the radio
disabled and only a start() will ever trigger it on.

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix power save count imbalance on ath_radio_enable()

Upon a failure we never call ath9k_ps_restore() on ath_radio_enable(),
this will throw off the sc->ps_usecount. When the sc->ps_usecount
is > 0 we never put the chip to full sleep. This drains battery,
and will also make the chip fail upon resume with:

ath: Starting driver with initial channel: 5745 MHz
ath: timeout (100000 us) on reg 0x7000: 0xdeadbeef & 0x00000003 != 0x00000000

This would make the chip useless upon resume.

I cannot prove this can happen but in theory it is so best to
avoid this race completely and not have users complain about
a broken device after resume.

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath: fix build break with ATH_DBG_WARN_ON_ONCE

Description by Hauke:

"If CONFIG_ATH_DEBUG=y is set ATH_DBG_WARN_ON_ONCE uses WARN_ON_ONCE and
returns something, but if CONFIG_ATH_DEBUG is not set it does not return
anything. Now ATH_DBG_WARN_ON_ONCE is used in the boolean expression in
an if case and is not returning anything and causes a compile error.

  CC [M]  /drivers/net/wireless/ath/ath9k/main.o
/drivers/net/wireless/ath/ath9k/main.c: In function ‘ath_isr’:
/drivers/net/wireless/ath/ath9k/main.c:769: error: expected expression
before ‘do’
make[5]: *** [/drivers/net/wireless/ath/ath9k/main.o] Error 1
make[4]: *** [/drivers/net/wireless/ath/ath9k] Error 2"

Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Fix modinfo does not list alias -> pci-id lines

The AHB bus support patchset moved the table "Known PCI ids" from base.c
to pci.c - unfortunately, MODULE_DEVICE_TABLE() was not transferred.
With this fix 'modinfo ath5k' lists the alias -> pci-id lines, again.

The issue was introduced by:
   commit e5b046d86fac609f636d127a38de94a175c7e83b
   "ath5k: Move PCI bus functions to separate file."

Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6

Conflicts:
drivers/net/wireless/ath/ath9k/ath9k.h
drivers/net/wireless/ath/ath9k/main.c
drivers/net/wireless/ath/ath9k/xmit.c

ath9k_hw: warn if we cannot change the power to the chip

Suspend requires the device to be in fullsleep otherwise upon
resume the device becomes unresponsive. We need to ensure
that when we want the device to go to sleep it yields to
the request, otherwise we'll have a useless devices upon
resume. Warn when changing the power fails as we need
to look into these issues.

Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: skip ATH9K_INT_TIM_TIMER when we are idle

We should not be idle when we get the ATH9K_INT_TIM_TIMER,
otherwise its a sign of something broken in our design with
our idle state machine and mac80211. Skip these and WARN once
just in case this is triggerable.

Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>

Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: add some element IDs in enum ieee80211_eid

1)WLAN_EID_BSS_COEX_2040
2)WLAN_EID_OVERLAP_BSS_SCAN_PARAM
3)WLAN_EID_EXT_CAPABILITY

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: rename config option for N-PHY, drop BROKEN

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: fix split of N-PHY devices into supported and not (based on PHY rev)

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: set TMS to work with current band width for N-PHY

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: silence warnings

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Show max number of probe tries in debug message.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: flush PHY writes when needed

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: implement own maskset

This let us avoid double addressing while still having reg check.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: reorder and optimize tables initialization

Order was changed in specs. For writing arrays we have designed bulk function
which makes use of auto increment and do not write table address over and over.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: update init tables

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Check for NULL sta in ath_tx_start

It can be NULL according to docs, and logging showed it
to be NULL in practice.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Apply ht_opmode changes in ieee80211_change_bss

Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: Add new BSS attribute ht_opmode

Add a new BSS attribute to allow hostapd to set the current HT opmode.
Otherwise drivers won't be able to set up protection for HT rates in
AP mode.

Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

orinoco: fix TKIP countermeasure behaviour

Enable the port when disabling countermeasures, and disable it on
enabling countermeasures.

This bug causes the response of the system to certain attacks to be
ineffective.

It also prevents wpa_supplicant from getting scan results, as
wpa_supplicant disables countermeasures on startup - preventing the
hardware from scanning.

wpa_supplicant works with ap_mode=2 despite this bug because the commit
handler re-enables the port.

The log tends to look like:

State: DISCONNECTED -> SCANNING
Starting AP scan for wildcard SSID
Scan requested (ret=0) - scan timeout 5 seconds
EAPOL: disable timer tick
EAPOL: Supplicant port status: Unauthorized
Scan timeout - try to get results
Failed to get scan results
Failed to get scan results - try scanning again
Setting scan request: 1 sec 0 usec
Starting AP scan for wildcard SSID
Scan requested (ret=-1) - scan timeout 5 seconds
Failed to initiate AP scan.

Reported by: Giacomo Comes <comes@naic.edu>
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

orinoco: clear countermeasure setting on commit

... and interface up.

In these situations, you are usually trying to connect to a new AP, so
keeping TKIP countermeasures active is confusing. This is already how
the driver behaves (inadvertently). However, querying SIOCGIWAUTH may
tell userspace that countermeasures are active when they aren't.

Clear the setting so that the reporting matches what the driver has
done..

Signed-off by: David Kilroy <kilroyd@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Fix BUG in pskb_expand_head when transmitting shared skbs

mac80211 doesn't handle shared skbs correctly at the moment. As a result
a possible resize can trigger a BUG in pskb_expand_head.

[  676.030000] Kernel bug detected[#1]:
[  676.030000] Cpu 0
[  676.030000] $ 0   : 00000000 00000000 819662ff 00000002
[  676.030000] $ 4   : 81966200 00000020 00000000 00000020
[  676.030000] $ 8   : 819662e0 800043c0 00000002 00020000
[  676.030000] $12   : 3b9aca00 00000000 00000000 00470000
[  676.030000] $16   : 80ea2000 00000000 00000000 00000000
[  676.030000] $20   : 818aa200 80ea2018 80ea2000 00000008
[  676.030000] $24   : 00000002 800ace5c
[  676.030000] $28   : 8199a000 8199bd20 81938f88 80f180d4
[  676.030000] Hi    : 0000026e
[  676.030000] Lo    : 0000757e
[  676.030000] epc   : 801245e4 pskb_expand_head+0x44/0x1d8
[  676.030000]     Not tainted
[  676.030000] ra    : 80f180d4 ieee80211_skb_resize+0xb0/0x114 [mac80211]
[  676.030000] Status: 1000a403    KERNEL EXL IE
[  676.030000] Cause : 10800024
[  676.030000] PrId  : 0001964c (MIPS 24Kc)
[  676.030000] Modules linked in: mac80211_hwsim rt2800lib rt2x00soc rt2x00pci rt2x00lib mac80211 crc_itu_t crc_ccitt cfg80211 compat arc4 aes_generic deflate ecb cbc [last unloaded: rt2800pci]
[  676.030000] Process kpktgend_0 (pid: 97, threadinfo=8199a000, task=81879f48, tls=00000000)
[  676.030000] Stack : ffffffff 00000000 00000000 00000014 00000004 80ea2000 00000000 00000000
[  676.030000]         818aa200 80f180d4 ffffffff 0000000a 81879f78 81879f48 81879f48 00000018
[  676.030000]         81966246 80ea2000 818432e0 80f1a420 80203050 81814d98 00000001 81879f48
[  676.030000]         81879f48 00000018 81966246 818432e0 0000001a 8199bdd4 0000001c 80f1b72c
[  676.030000]         80203020 8001292c 80ef4aa2 7f10b55d 801ab5b8 81879f48 00000188 80005c90
[  676.030000]         ...
[  676.030000] Call Trace:
[  676.030000] [<801245e4>] pskb_expand_head+0x44/0x1d8
[  676.030000] [<80f180d4>] ieee80211_skb_resize+0xb0/0x114 [mac80211]
[  676.030000] [<80f1a420>] ieee80211_xmit+0x150/0x22c [mac80211]
[  676.030000] [<80f1b72c>] ieee80211_subif_start_xmit+0x6f4/0x73c [mac80211]
[  676.030000] [<8014361c>] pktgen_thread_worker+0xfac/0x16f8
[  676.030000] [<8002ebe8>] kthread+0x7c/0x88
[  676.030000] [<80008e0c>] kernel_thread_helper+0x10/0x18
[  676.030000]
[  676.030000]
[  676.030000] Code: 24020001  10620005  2502001f <0200000d> 0804917a  00000000  2502001f  00441023  00531021

Fix this by making a local copy of shared skbs prior to mangeling them.
To avoid copying the skb unnecessarily move the skb_copy call below the
checks that don't need write access to the skb.

Also, move the assignment of nh_pos and h_pos below the skb_copy to point
to the correct skb.

It would be possible to avoid another resize of the copied skb by using
skb_copy_expand instead of skb_copy but that would make the patch more
complex. Also, shared skbs are a corner case right now, so the resize
shouldn't matter much.

Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Fix suspend/resume

The HW has to be set to FULLSLEEP mode during suspend,
when no interface has been brought up. Not doing this would
break resume, as the chip won't be powered up at all.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Put the right tsf value in mesh beacons

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Prevent mesh interfaces from being counted as ad-hoc

This results in an erroneus num_adhoc_vifs count, as the this counter
was incremented but not decremented for mesh interfaces.

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Fix beaconing in mesh mode

This patch fixes the oops below when attempting to bring up a mesh
interface on ath5k hardware.

[  128.933099] kernel BUG at drivers/net/wireless/ath/ath5k/base.c:197!
[  128.933099] invalid opcode: 0000 [#1]
(...)
[  128.933099] Call Trace:
[  128.933099]  [<c83b77fa>] ? ath5k_beacon_update+0x57/0x1f8 [ath5k]
[  128.933099]  [<c02d9a40>] ? __sysfs_add_one+0x28/0x76
[  128.933099]  [<c83b830e>] ? ath5k_bss_info_changed+0x13f/0x173
[ath5k]
[  128.933099]  [<c82ff629>] ? ieee80211_config_beacon+0xc0/0x17e
[mac80211]
[  128.933099]  [<c82f073e>] ?
ieee80211_bss_info_change_notify+0x182/0x18b [mac80211]
[  128.933099]  [<c83b81cf>] ? ath5k_bss_info_changed+0x0/0x173 [ath5k]
[  128.933099]  [<c82ff6d6>] ? ieee80211_config_beacon+0x16d/0x17e
[mac80211]
[  128.933099]  [<c82ff753>] ? ieee80211_add_beacon+0x34/0x39 [mac80211]
[  128.933099]  [<c830a4ed>] ? ieee80211s_init+0xf8/0x10f [mac80211]
[  128.933099]  [<c830a5df>] ? ieee80211_mesh_init_sdata+0xdb/0x154 [mac80211]

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

orinoco: initialise priv->hw before assigning the interrupt

The interrupt handler takes a lock - but since commit bcad6e80f3f this
lock goes through an indirection specified in the hermes_t structure.
We must therefore initialise the structure before setting up the
interrupt handler.

Fix orinoco_cs and spectrum_cs

<https://bugzilla.kernel.org/show_bug.cgi?id=23932>

Bisected by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Fix compilation error when mesh is disabled

Wrap mesh sections inside CONFIG_MAC80211_MESH to fix compilation
problems reported by Stephen Rothwell, Larry Finger and Bruno Randolf.

Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Remove dead code in recv.c

The structure struct ieee80211_rx_status *rxs is no longer needed to be
passed to ath_rx_send_to_mac80211 function

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Parse DTIM period from mac80211

With the current save power save implementation we assume a dtim period
of 1.This value is assigned based on a sanity check in the driver
eventhough we had not parsed it from mac80211.This patch obtains the actual
DTIM period from AP by parsing it from mac80211.Yet for handling
multicast traffic we may still have it as fixed rather than parsing it
from mac80211 .This does not breaks power save or anything as the sleep
duration is currently fixed in the driver.This patch may serve to improve
power save in the future by using dtim period for sleep duration and using
correct dtim period adhoc mode.

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Properly use unlikely check macro

AUTOSLEEP feature is enabled only for AR9271 and AR9003 version
chipsets.So unlikely macro should be used only to check whether
auto-sleep feature is enabled

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Fix panic on FW download failure

Use the correct error condition exit in case firmware download
fails for some reason. Not doing so results in a panic:

usb 1-3: ath9k_htc: Transferred FW: ar9271.fw, size: 51280
usb 1-3: ath9k_htc: Firmware - ar9271.fw download failed
usb 1-3: ath9k_htc: Target is unresponsive
Failed to initialize the device
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Pid: 2823, comm: insmod Tainted: G        W   2.6.37-rc4-wl #11
Call Trace:
[<ffffffff81090d7e>] __lock_acquire+0xe3e/0x1d00
[<ffffffff813a9f14>] ? restore_args+0x0/0x30
[<ffffffff81058af1>] ? vprintk+0x321/0x500
[<ffffffff81092290>] lock_acquire+0xa0/0x190
[<ffffffffa02a0eac>] ? usb_kill_anchored_urbs+0x1c/0x80 [usbcore]
[<ffffffff813a8ea8>] _raw_spin_lock_irq+0x48/0x60
[<ffffffffa02a0eac>] ? usb_kill_anchored_urbs+0x1c/0x80 [usbcore]
[<ffffffff813a53fd>] ? printk+0x3c/0x3f
[<ffffffffa02a0eac>] usb_kill_anchored_urbs+0x1c/0x80 [usbcore]
[<ffffffffa0055388>] ath9k_hif_usb_dealloc_urbs+0x18/0x40 [ath9k_htc]
[<ffffffffa00557d7>] ath9k_hif_usb_probe+0x227/0x3d0 [ath9k_htc]
[<ffffffffa02a56ac>] usb_probe_interface+0x10c/0x210 [usbcore]
[<ffffffff812ae826>] driver_probe_device+0x96/0x1c0
[<ffffffff812ae9f3>] __driver_attach+0xa3/0xb0
[<ffffffff812ae950>] ? __driver_attach+0x0/0xb0
[<ffffffff812ad6ae>] bus_for_each_dev+0x5e/0x90
[<ffffffff812ae4c9>] driver_attach+0x19/0x20
[<ffffffff812ae038>] bus_add_driver+0x168/0x320
[<ffffffff812aec71>] driver_register+0x71/0x140
[<ffffffff811fc338>] ? __raw_spin_lock_init+0x38/0x70
[<ffffffffa02a438c>] usb_register_driver+0xdc/0x190 [usbcore]
[<ffffffffa0063000>] ? ath9k_htc_init+0x0/0x4f [ath9k_htc]
[<ffffffffa005599e>] ath9k_hif_usb_init+0x1e/0x20 [ath9k_htc]
[<ffffffffa006302b>] ath9k_htc_init+0x2b/0x4f [ath9k_htc]
[<ffffffff8100212f>] do_one_initcall+0x3f/0x180
[<ffffffff8109ef9b>] sys_init_module+0xbb/0x200
[<ffffffff8100bf52>] system_call_fastpath+0x16/0x1b

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Add support for handling TX power configuration

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Cleanup device identification

ath.ko is a common module shared between ath5k, ar9170usb, ath9k and ath9k_htc.
Adding driver specific data to the shared structure would impact all the
drivers. Handling USB device recognition for devices specific to ath9k_htc
can be handled within the driver itself.

Also, AR7010 refers to the processor used in both AR9280/AR9287 based
devices. Rename the device enumerations accordingly.

While at it, check properly for the bus type when choosing the EEPROM
base address for UB95.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix a compiler warning

net/mac80211/mlme.c: In function 'ieee80211_sta_work':
net/mac80211/mlme.c:1981: warning: too many arguments for format

Introduced by commit 04ac3c0ee2c773c321ec472d892635a20556f34d
("mac80211: speed up AP probing using nullfunc frames").

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Use capabilities information for the number of TX queues

One thing I missed in my WME series: Older hardware does not have enough
hardware queues to support WME. In this case we just set up one data queue. Use
the capability information to decide how many queues to set up.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Make DMA warning in ath_stoprecv WARN_ON_ONCE.

This decreases spammage in the log.  A single line message
will still be printed, so users can be aware that problem
exists.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Add device id of AR9485 to pci table

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Disable MRC CCK for AR9485

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Setup paprd only for supported chains

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Program appropriate register for temperature compensation cal for AR9485

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Add IQ cal changes for AR9485

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Define IQcal correction coefficient registers using index

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Program appropriate chianmask for AR9485 before starting AGC/IQ cal

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Configure power control only for the supported chains

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Read and configure turnning caps to regulate freq accuracy

Right now it is done for only AR9485, will be done for ar9003 also
after proper testing.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Configure internal regulator for AR9485

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Read and configure antenna diversity control for AR9485

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Configure xpa bias level for AR9485

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Read spur channel information from eeprom for AR9485

Also spur channel count and range is different for AR9485.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Add a helper function to get spur channel pointer from cal data for AR9003 family

This helper function would be used for AR9485.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Find chansel of AR_PHY_65NM_CH0_SYNTH7 for AR9485

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Configure pll control for AR9485

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Find the maximum number of chains that hw supports

Have it in ah->caps. This will be used during various
calibrations.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Enable extended synch for AR9485 to fix L0s recovery issue

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Disable TX STBC for AR9485

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Disable LDPC for AR9485

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Eeeprom changes for AR9485

Calibration data are stored at 4k address (0xfff). The cal data
for AR9485 is not compressed so its lengh can exceed 1024 limit,
take care of that.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Initialize tx/rx gain table from initvals.h for AR9485

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Initialize mode registers for AR9485

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Enable hw initialization for AR9485

Also make it a supported mac

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Add initvals.h for AR9485

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Define hw version macros for AR9485

AR9485 is a single chain and single band (2.4 Ghz) chip.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>