Nick Bowler [Wed, 25 Mar 2020 02:00:28 +0000 (22:00 -0400)]
kernel: package f71882fg hwmon driver
This driver enables hardware monitoring support using the sensors
found in many Fintek Super-IO chips.
Signed-off-by: Nick Bowler <nbowler@draconx.ca>
Eneas U de Queiroz [Fri, 27 Mar 2020 02:20:08 +0000 (23:20 -0300)]
openssl: revert EOF detection change in 1.1.1
This adds patches to avoid possible application breakage caused by a
change in behavior introduced in 1.1.1e. It affects at least nginx,
which logs error messages such as:
nginx[16652]: [crit] 16675#0: *358 SSL_read() failed (SSL: error:
4095126:SSL routines:ssl3_read_n:unexpected eof while reading) while
keepalive, client: xxxx, server: [::]:443
Openssl commits
db943f4 (Detect EOF while reading in libssl), and
22623e0 (Teach more BIOs how to handle BIO_CTRL_EOF) changed the
behavior when encountering an EOF in SSL_read(). Previous behavior was
to return SSL_ERROR_SYSCALL, but errno would still be 0. The commits
being reverted changed it to SSL_ERRO_SSL, and add an error to the
stack, which is correct. Unfortunately this affects a number of
applications that counted on the old behavior, including nginx.
The reversion was discussed in openssl/openssl#11378, and implemented as
PR openssl/openssl#11400.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Baptiste Jonglez [Thu, 26 Mar 2020 18:03:42 +0000 (19:03 +0100)]
ar71xx: Fix gigabit switch support for Mikrotik RB951G-2HnD
Without this patch, when using rev 3 of the Atheros AR9344 SoC, the
gigabit switch (AR8327) does not work or works very erratically.
This is a re-spin of http://patchwork.ozlabs.org/patch/419857/ with a
different PLL value, according to the feedback from several users
(including myself) as shown here:
https://openwrt.org/toh/mikrotik/rb2011uias#tracking_reported_experience_with_suggested_patch_for_the_5_gige_ports
Performance is acceptable: testing L3 forwarding without NAT yields a
performance of 370 Mbit/s (iperf3 TCP) and 41 Kpps (iperf3 UDP with 64
bytes payload). Both tests show that 100% of CPU time is spent on softirq.
A similar fix for a different device (RB2011) was added in
e457d22261
("Make GBit switch work on RB2011").
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
Petr Štetiar [Thu, 26 Mar 2020 14:19:42 +0000 (15:19 +0100)]
kernel: bump 5.4 to 5.4.28
Changelog since 5.4.24 mentions CVE-2019-19769, CVE-2020-8648,
CVE-2020-8649 and CVE-2020-8647.
Removed upstreamed:
generic: 507-v5.6-iio-chemical-sps30-fix-missing-triggered-buffer-depe.patch
generic: 600-ipv6-addrconf-call-ipv6_mc_up-for-non-Ethernet-inter.patch
bcm27xx: 950-0435-ASoC-pcm512x-Fix-unbalanced-regulator-enable-call-in.patch
ipq806x: 701-stmmac-fix-notifier-registration.patch
lantiq: 002-pinctrl-falcon-fix-syntax-error.patch
octeontx: 0002-net-thunderx-workaround-BGX-TX-Underflow-issue.patch
Run tested: apu2, qemu-x86-64, apalis, a64-olinuxino, nbg6617
Build tested: sunxi/a53, imx6, x86/64, ipq40xx
Tested-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> [apu2]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Tue, 24 Mar 2020 10:09:41 +0000 (11:09 +0100)]
ipq40xx: switch to 5.4 kernel
5.4.24 seems to be working fine on my zyxel,nbg6617, so let's start
wider userbase testing.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Leon M. George [Mon, 11 Nov 2019 13:10:50 +0000 (14:10 +0100)]
ipq40xx: wpj428: fix missing MDIO GPIO reset and pinmux
The bootloader does not always initialize the MDIO pins before booting
Linux. E.g. on version "U-Boot 2012.07 [Chaos Calmer 15.05.1,r35193] (Jul
25 2017 - 11:36:26)" this is the case when booting automatically without
activating the U-Boot console.
Without this change, the kernel boot will complain about missing PHYs:
libphy: ipq40xx_mdio: probed
ar40xx
c000000.ess-switch: Probe failed - Missing PHYs!
libphy: Fixed MDIO Bus: probed
With this change it will work as expected:
libphy: ipq40xx_mdio: probed
ESS reset ok!
ESS reset ok!
libphy: Fixed MDIO Bus: probed
Ref: GH-2835
Tested-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
Signed-off-by: Leon M. George <leon@georgemail.eu>
[commit description from Fredrik, subject facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Thu, 26 Mar 2020 12:14:32 +0000 (13:14 +0100)]
sunxi: switch to 5.4 kernel
Seems to be working fine on my a64-olinuxino, it's 99.9% upstream stuff
anyway. Lets start wider userbase testing.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Thu, 26 Mar 2020 12:06:12 +0000 (13:06 +0100)]
sunxi: a53: fix ethernet on a64-olinuxino
a64-olinuxino board has Micrel KSZ9031 Gigabit PHY so add support for
this PHY into kernel.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Wed, 18 Mar 2020 23:43:14 +0000 (00:43 +0100)]
sunxi: 5.4: dts: a64: olinuxino: add bank supply regulators
This is backport of v5.6 patch.
Allwinner A64 SoC has separate supplies for PC, PD, PE, PG and PL. This
patch adds regulators for them to the pinctrl node.
Exception is PL which is used by the RSB bus. To avoid circular
dependencies, VCC-PL is omitted.
On boards with eMMC, VCC-PC is supplied by ELDO1, instead of DCDC1.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Thu, 26 Mar 2020 09:13:57 +0000 (10:13 +0100)]
sunxi: 5.4: a64-olinuxino: use red LED for status signalization
There is a red LED marked as `GPIO_LED1` on the silkscreen and connected
to PE17, so use this LED for status signalization.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Mon, 16 Mar 2020 09:57:50 +0000 (10:57 +0100)]
sunxi: a53: add support for Olimex A64-Olinuxino eMMC
Specifications:
SoC: Allwinner A64 (1.2 GHz Quad-Core ARM Cortex-A53 64-bit)
RAM: 1GB or 2GB RAM DDR3L @ 672Mhz
Flash: 0/4/16GB eMMC flash memory for storage and boot
MicroSD card connector for cards up to 32GB
Debug: serial UART debug header with 0.1" pins
Wired connectivity: 10/100/1000Mbps GbE Ethernet
Wireless connectivity: on-board RTL8723BS 1T1R 802.11bgn WiFi and
Bluetooth 4.0 module with built-in antenna
(only available in the A64-OLinuXino-1G4GW)
Flashing instructions:
Standard sunxi SD card installation procedure - copy eMMC image to SD
card, insert in into SD card slot on the device and boot. You should see
something like following if the eMMC is detected correctly:
mmcblk2: mmc2:0001 P1XXXX 3.60 GiB
mmcblk2boot0: mmc2:0001 P1XXXX partition 1 16.0 MiB
mmcblk2boot1: mmc2:0001 P1XXXX partition 2 16.0 MiB
Then flash SD card eMMC image straight into the mmcblk2 device:
dd if=/mnt/openwrt...a64-olinuxino-emmc-squashfs-sdcard.img of=/dev/mmcblk2
It also possible to boot from boot0 partition[1]:
1. Compile U-Boot with CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x40
otherwise the U-Boot will get stuck in bootloop
2. Configure eMMC to boot from boot0 partition inside U-Boot:
mmc bootbus 1 1 0 0; mmc partconf 1 1 1 0
3. echo 0 > /sys/block/mmcblk2boot0/force_ro
4. Write U-Boot from offset 0 (not offset 8k as with SD card) into
boot0 partition
dd if=u-boot-sunxi-with-spl.bin of=/dev/mmcblk2boot0
Known issues:
Wireless doesn't work properly via netifd.
1. https://linux-sunxi.org/index.php?title=Bootable_eMMC
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Mon, 16 Mar 2020 09:57:50 +0000 (10:57 +0100)]
sunxi: a53: add support for Olimex A64-Olinuxino
Specifications:
SoC: Allwinner A64 (1.2 GHz Quad-Core ARM Cortex-A53 64-bit)
RAM: 1GB or 2GB RAM DDR3L @ 672Mhz
Flash: 0/4/16GB eMMC flash memory for storage and boot
MicroSD card connector for cards up to 32GB
Debug: serial UART debug header with 0.1" pins
Wired connectivity: 10/100/1000Mbps GbE Ethernet
Wireless connectivity: on-board RTL8723BS 1T1R 802.11bgn WiFi and
Bluetooth 4.0 module with built-in antenna
(only available in the A64-OLinuXino-1G4GW)
Flashing instructions:
Standard sunxi SD card installation procedure - copy image to SD card,
insert in into SD card slot on the device and boot.
Known issues:
Wireless doesn't work properly via netifd.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Mon, 16 Mar 2020 09:56:01 +0000 (10:56 +0100)]
sunxi: a53: image: make it DRY
Replace same copy&pasted lines with the appropriate reusable bits.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Wed, 18 Mar 2020 14:00:22 +0000 (15:00 +0100)]
uboot-sunxi: a64: allow booting directly from eMMC
Current boot script uses hardcoded bootdevice, which allows booting from
SD card only, so this patch allows booting directly from eMMC as well.
While at it, replace fixed root device with more flexible UUID based
probing, so from now on probing order of MMC device doesn't matter.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Mon, 16 Mar 2020 14:37:54 +0000 (15:37 +0100)]
uboot-sunxi: add support for Olimex A64-Olinuxino eMMC
Adding U-Boot image for Olimex A64-Olinuxino eMMC, including patch which
adds eMMC boot partition configuration commands.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Mon, 16 Mar 2020 14:37:54 +0000 (15:37 +0100)]
uboot-sunxi: add support for Olimex A64-Olinuxino
Adding U-Boot image for Olimex A64-Olinuxino.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Wed, 25 Mar 2020 11:55:45 +0000 (12:55 +0100)]
uboot-sunxi: rename Sinovoip BPI M2 Plus to Bananapi M2 Plus H3
Rename the board as done in upstream commit
268ae6548779 ("sunxi: Rename
Sinovoip BPI M2 Plus to Bananapi M2 Plus H3") which backs the rename
with the following reasoning:
The brand Sinovoip is used for Sinovoip's original VOIP products, while
the Bananapi brand is for the single board computers they produce. This
has been verified by Bananapi. Rename the board from "Sinovoip BPI M2
Plus" to "Bananapi M2 Plus". For the defconfig file, all lowercase is
used.
To support the H5 variant of this board, the "H3" suffix is added to
the defconfig name.
This has to be done in order to allow building U-Boot past v2019.04
release where this change was introduced.
Ref: https://github.com/openwrt/openwrt/pull/2849#discussion_r396401489
Suggested-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Aleksander Jan Bajkowski [Sun, 9 Feb 2020 17:27:48 +0000 (18:27 +0100)]
uboot-sunxi: Banana Pi M2 Ultra switch to mainline defconfig
U-boot also have defconfig for this board. In 2019.01 branch they are identical.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Petr Štetiar [Mon, 16 Mar 2020 13:47:07 +0000 (14:47 +0100)]
uboot-sunxi: bump to 2020.01
Refreshed patches, removed following, probably obsolete patches:
221-compatible-old-dtc.patch
240-sun50i-h5-Orange-Pi-Zero-Plus-Fix-SdCard-detection.patch
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Wed, 18 Mar 2020 15:51:13 +0000 (16:51 +0100)]
linux-firmware: add firmware for RTL8723BS SDIO modules
Adds firmware package for Realtek RTL8723BS SDIO Wireless LAN NIC driver
available in the staging.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Wed, 18 Mar 2020 15:54:03 +0000 (16:54 +0100)]
mac80211: realtek: add staging driver for RTL8723BS SDIO module
Adds kernel module for Realtek RTL8723BS SDIO Wireless LAN NIC driver
available in the staging.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Sun, 8 Mar 2020 21:33:11 +0000 (22:33 +0100)]
bcm27xx: 5.4: add support for Sensirion SPS30 in i2c-sensor overlay
Add support for Sensirion SPS30 particulate matter sensor with fixed
address 0x69.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Thibaut VARÈNE [Tue, 17 Mar 2020 16:53:44 +0000 (17:53 +0100)]
ath79: rename Mikrotik RB 922UAGS-5HPacD mtd partition
In RouterBOARD parlance there never was an "art" partition.
This partition has always been named 'hard_config' on ar71xx.
This partition contains more than just ART (Atheros Radio Test) data. It
includes the hardware description (product code, serial, board
identifier, name, hardware options, MAC address), as well as other bits
affecting the operation of RouterBoot.
To avoid confusion with regular ART data, this partition is renamed in
line with historical ar71xx and ramips nomenclature as 'hard_config'.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Thibaut VARÈNE [Tue, 17 Mar 2020 16:53:43 +0000 (17:53 +0100)]
ath79: fix Mikrotik wAP G-5HacT2HnD mtd partitions
In RouterBOARD parlance there never was an "art" partition.
This partition has always been named 'hard_config' on ar71xx.
This partition contains more than just ART (Atheros Radio Test) data. It
includes the hardware description (product code, serial, board
identifier, name, hardware options, MAC address), as well as other bits
affecting the operation of RouterBoot.
To avoid confusion with regular ART data, this partition is renamed in
line with historical ar71xx and ramips nomenclature as 'hard_config'.
This commit fixes the previous support files and implements the nested
RouterBoot partition scheme as already used by ramips-based SPI-NOR
RouterBOARD DTSes, as previously reviewed and implemented in
bbe2cf657ca7 ("ramips: fix RBM11G partitioning").
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Alberto Bursi [Fri, 27 Mar 2020 11:21:30 +0000 (12:21 +0100)]
kirkwood: fix DTS partitions for Pogoplug E02
The Pogoplug E02 was not using the correct partitions
in device tree, but used the ones from upstream and
thus could not boot OpenWrt images.
In contrast, uboot-kirkwood is using the correct
partitions since
d3fc4fbd74dc ("uboot-kirkwood: re-add
Pogoplug E02 support").
This patch corrects the partitions in DTS for kernels
4.14, 4.19 and 5.4.
Fixes: 2b0fa00da8fc ("kirkwood: add Pogoplug E02 Kernel support")
Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
[commit title/message facelift, refresh 4.14 patch]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
John Crispin [Fri, 27 Mar 2020 15:13:06 +0000 (16:13 +0100)]
mediatke: add support for elecom-wrc-2533gent
This commit adds support for the MT7622-based Elecom WRC-2533gent router,
with spi-nand storage and 512MB RAM.
The device has the following specifications:
* MT7622 (arm64 dual-core)
* 512MB RAM (DDR3)
* 4GB storage (spi-nand)
* 5x 1Gbps Ethernet (RTL8337C switch)
* 1x UART header
* 1x USB 3.0 port
* 5x LEDs
* 1x reset button
* 1x WPS button
* 1x slider switch
* 1x DC jack for main power (12V)
The following has been tested and is working:
* Ethernet switch
* 2.4g and 5g wifi
* USB 3.0 port
* sysupgrade
* buttons/leds
Not working:
* bluetooth firmware does not load even though it is present int he rootfs
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Fri, 27 Mar 2020 14:34:33 +0000 (15:34 +0100)]
mediatek: more v5.4 mtd fixes
Signed-off-by: John Crispin <john@phrozen.org>
John Crispin [Fri, 27 Mar 2020 11:40:23 +0000 (12:40 +0100)]
hostapd: fix no_reload logic
the code would unconditionally tear down all interfaces upon a reconf.
This should only be done when the reconf call fails.
Signed-off-by: John Crispin <john@phrozen.org>
Rafał Miłecki [Fri, 27 Mar 2020 13:55:58 +0000 (14:55 +0100)]
mac80211: fix brcmfmac monitor interface crash
This fixes bug in brcmfmac *exposed* by ipv6/addrconf fix.
Fixes: ec8e8e2ef082 ("kernel: backport out-of-memory fix for non-Ethernet devices")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Álvaro Fernández Rojas [Thu, 26 Mar 2020 07:44:43 +0000 (08:44 +0100)]
ath10k-firmware: update ath10k-ct firmware images
Release notes for 017:
Wave-1:
* March 19, 2020: Fix problem where power-save was not enabled when going off-channel to scan.
The problem was a boolean logic inversion in the chmgr code, a regression I introduced
a long time ago.
* March 19, 2020: When scanning only on current working channel, do not bother with disable/enable
powersave. This should make an on-channel scan less obtrusive than it was previously.
* March 23, 2020: Fix channel-mgr use-after-free problem that caused crashes in some cases. The crash
was exacerbated by recent power-save changes.
* March 23, 2020: Fix station-mode power-save related crash: backported the fix from 10.2 QCA firmware.
* March 23, 2020: Attempt to better clean up power-save objects and state, especially in station mode.
Release notes for 016:
Wave-1 changes, some debugging code for a crash someone reported, plus:
* February 28, 2020: Fix custom-tx path when sending in 0x0 for rate-code. Have tries == 0 mean
one try but NO-ACK (similar to how wave-2 does it).
wave-2:
* Fixed some long-ago regressions related to powersave and/or multicast. Maybe fix some
additional multicast and/or tx-scheduling bugs.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Petr Štetiar <ynezz@true.cz>
Álvaro Fernández Rojas [Thu, 19 Mar 2020 10:36:13 +0000 (11:36 +0100)]
ath10k-ct: update to version 2020-03-25
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Petr Štetiar <ynezz@true.cz>
Hans Dedecker [Thu, 26 Mar 2020 20:55:52 +0000 (21:55 +0100)]
netifd: fix compilation with musl 1.2.0
1e8328 system-linux: fix compilation with musl 1.2.0
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Hans Dedecker [Thu, 26 Mar 2020 20:50:54 +0000 (21:50 +0100)]
odhcp6c: fix compilation with musl 1.2.0
49305e6 odhcp6c: fix compilation with musl 1.2.0
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Jan Alexander [Tue, 24 Mar 2020 12:36:57 +0000 (13:36 +0100)]
ar71xx: use status led for GL.iNet GL-AR750S
Use power led for device status.
The status led behavior has already been fixed in
af28d8a539fe
("ath79: add support for GL.iNet GL-AR750S") when porting the
device to ath79. This fixes it for ar71xx as well.
Signed-off-by: Jan Alexander <jan@nalx.net>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Mon, 9 Dec 2019 14:00:55 +0000 (15:00 +0100)]
ath79: add support for TP-Link TL-WA860RE v1
This ports support for the TL-WA860RE v1 range extender from ar71xx
to ath79.
Specifications:
Board: AP123 / AR9341 rev. 3
Flash/RAM: 4/32 MiB
CPU: 535 MHz
WiFi: 2.4 GHz b/g/n
Ethernet: 1 port (100M)
Two external antennas
Flashing instructions:
Upload the factory image via the vendor firmware upgrade option.
Recovery:
Note that this device does not provide TFTP via ethernet like many
other TP-Link devices do. You will have to open the case if you
require recovery beyond failsafe.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Sebastian Knapp <sebastian4842@outlook.com>
Adrian Schmutzler [Mon, 9 Dec 2019 12:44:03 +0000 (13:44 +0100)]
ath79: add support for TP-Link TL-WDR4310 v1
This device seems to be identical to the TL-WDR4300, just with
different release date/region and TPLINK_HWID.
Support is added based on the ar71xx implementation.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Henrique de Moraes Holschuh [Sun, 1 Mar 2020 03:08:43 +0000 (00:08 -0300)]
dnsmasq: fix dnssec+ntp chicken-and-egg workaround (FS#2574)
Fix the test for an enabled sysntp initscript in dnsmasq.init, and get
rid of "test -o" while at it.
Issue reproduced on openwrt-19.07 with the help of pool.ntp.br and an
RTC-less ath79 router. dnssec-no-timecheck would be clearly missing
from /var/etc/dnsmasq.conf.* while the router was still a few days in
the past due to non-working DNSSEC + DNS-based NTP server config.
The fix was tested with the router in the "DNSSEC broken state": it
properly started dnsmasq in dnssec-no-timecheck mode, and eventually ntp
was able to resolve the server name to an IP address, and set the system
time. DNSSEC was then enabled by SIGINT through the ntp hotplug hook,
as expected.
A missing system.ntp.enabled UCI node is required for the bug to show
up. The reasons for why it would be missing in the first place were not
investigated.
Signed-off-by: Henrique de Moraes Holschuh <henrique@nic.br>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
Henrique de Moraes Holschuh [Sun, 1 Mar 2020 02:31:45 +0000 (23:31 -0300)]
dnsmasq: init: get rid of test -a and test -o
Refer to shellcheck SC2166. There are just too many caveats that are
shell-dependent on test -a and test -o to use them.
Signed-off-by: Henrique de Moraes Holschuh <henrique@nic.br>
Jo-Philipp Wich [Wed, 25 Mar 2020 18:34:34 +0000 (19:34 +0100)]
uclient: update mirror hash
Fixes: 98017228dd ("uclient: bump to latest Git HEAD")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Jo-Philipp Wich [Wed, 25 Mar 2020 18:32:18 +0000 (19:32 +0100)]
uclient: bump to latest Git HEAD
af585db uclient-fetch: support specifying advertised TLS ciphers
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Jo-Philipp Wich [Wed, 25 Mar 2020 18:22:10 +0000 (19:22 +0100)]
uhttpd: bump to latest Git HEAD
5e9c23c client: allow keep-alive for POST requests
5fc551d tls: support specifying accepted TLS ciphers
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Jo-Philipp Wich [Wed, 25 Mar 2020 18:16:19 +0000 (19:16 +0100)]
ustream-ssl: bump to latest Git HEAD
5e1bc34 ustream-openssl: clear error stack before SSL_read/SSL_write
f7f93ad add support for specifying usable ciphers
Also bump the ABI version since the layout of `struct ustream_ssl_ops`
changed.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Kevin Darbyshire-Bryant [Tue, 24 Mar 2020 11:05:27 +0000 (11:05 +0000)]
build: prereq: tidy gcc version checks
There is a restriction in the number of parameters(10) that may be passed to
the SetupHostCommand macro so continually adding explicit gcc'n' version
checks ends up breaking the compiler check for the later versions and
oddballs like Darwin as was done in
835d1c68a0 which added gcc10.
Drop all the explicitly specified gcc version checks. If a suitable gcc
compiler is not found, it may be specified at the dependency checking
stage after which that version will be symlinked into the build staging
host directory.
eg. 'CC=gccfoo CXX=g++foo make prereq'
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Kevin Darbyshire-Bryant [Tue, 24 Mar 2020 09:51:36 +0000 (09:51 +0000)]
nftables: bump to 0.9.3
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Kevin Darbyshire-Bryant [Mon, 23 Mar 2020 15:04:51 +0000 (15:04 +0000)]
libnftnl: drop unsupported configure option
--without-json-parsing is not a supported configure option.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Paul Spooren [Mon, 23 Mar 2020 18:53:46 +0000 (08:53 -1000)]
x86/geode: fixup FEATURE inheritance
In the geode subtarget all default x86 features were overwritten via :=
instead of extending them via +=.
This patch fixes the inheritance and thereby the compilation of
x86/geode target.
Compile tested x86/geode.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Paul Spooren [Mon, 23 Mar 2020 10:25:33 +0000 (00:25 -1000)]
x86/geode: add missing include after rebase
The x86 image generation was refacted via
cb007a7bf6 and accidently not
included `geode.mk` when selected as subtarget.
Now the file is included and image compilation for x86/geode works
again.
Thanks to Russell Senior <russell@personaltelco.net> for reporting the
problem and suggesting a patch!
Signed-off-by: Paul Spooren <mail@aparcar.org>
Álvaro Fernández Rojas [Mon, 23 Mar 2020 08:14:36 +0000 (09:14 +0100)]
bcm27xx: refresh linux 5.4 configs
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Álvaro Fernández Rojas [Mon, 23 Mar 2020 08:06:49 +0000 (09:06 +0100)]
bcm27xx-userland: update to latest version
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Álvaro Fernández Rojas [Mon, 23 Mar 2020 07:55:14 +0000 (08:55 +0100)]
bcm27xx-gpu-fw: update to latest version
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Álvaro Fernández Rojas [Mon, 23 Mar 2020 07:48:08 +0000 (08:48 +0100)]
bcm27xx: sync 5.4 patches with RPi Foundation
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Robert Marko [Wed, 18 Mar 2020 18:39:43 +0000 (19:39 +0100)]
build: add GCC 10 version detection
Lets add GCC 10 detection to the build system as distributions like Fedora 32 have started shipping with it.
Some tools like mtd-utils need work to compile under GCC10, but that will be next step.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Christian Lamparter [Sat, 21 Mar 2020 19:56:57 +0000 (20:56 +0100)]
apm821xx: switch to 5.4 kernel
This patch switches the APM821XX target to the linux kernel 5.4 variant.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Sat, 21 Mar 2020 20:40:15 +0000 (21:40 +0100)]
apm821xx: wndr4700: add preliminary drivetemp sensor
This patch prepares the WNDR4700 to use the HDD sensor for
the thermal zone. While the kernel's thermal.txt device-tree
binding documentation files talks about supporting multiple
sensors for a zone. This sadly is NOT the case. Even the most
current upstream kernels (5.6-rc) supports just >one< sensor
per zone: (driver/base/of-thermal.c:886)
| * REVIST: for now, the thermal framework supports only
| * one sensor per thermal zone. Thus, we are considering
| * only the first two values as slope and offset.
I do hope that this warning will prevent others wasteing time
on trying to figure out why their multi-sensor thermal-zones
definitions are not working as specified.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Sat, 21 Mar 2020 19:58:16 +0000 (20:58 +0100)]
apm821xx: add drivetemp sensor for the WD MyBook Series
This patch adds the hwmon-drivetemp to the device.
It also adds device-tree bindings. This can be useful to
automate external fans which can be controlled for example
by either an unused sata-port or by the usb-power regulator.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Sun, 22 Mar 2020 19:39:16 +0000 (20:39 +0100)]
x86: geode/legacy: fix missing watchdog core dependencies
This patch follows the other patches that added the watchdog
core to various (armvirt, malta, ath79, ...) targets that
have been hit by the following build error:
Package kmod-hwmon-sch5627 is missing dependencies for the following libraries:
watchdog.ko
In theory, we could have just added the CONFIG_WATCHDOG_CORE=y
to the Kconfig variable of kmod-hwmon-sch5627's package definition.
This would have forced the watchdog core to be builtin and less
architectures would need to be updated. But we might as well follow
through here.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Jordan Sokolic [Thu, 19 Mar 2020 12:23:22 +0000 (14:23 +0200)]
dnsmasq: add 'scriptarp' option
Add option 'scriptarp' to uci dnsmasq config to enable --script-arp functions.
The default setting is false, meaning any scripts in `/etc/hotplug.d/neigh` intended
to be triggered by `/usr/lib/dnsmasq/dhcp-script.sh` will fail to execute.
Also enable --script-arp if has_handlers returns true.
Signed-off-by: Jordan Sokolic <oofnik@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
David Bauer [Sun, 22 Mar 2020 19:06:23 +0000 (20:06 +0100)]
ath79: fix missing return statement in ar934x_nand
The reset assert and deassert methods currently miss
a return value, leading to a compilation warning.
Return the return-value of reset_control_assert and
reset_control_deassert to fix these warnings.
Suggested-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Tue, 17 Mar 2020 20:59:27 +0000 (21:59 +0100)]
ath79: fix NAND driver compilation for kernel 5.4
This fixes the compilation of the AR934x NAND controller
driver for kernel 5.4 while leaving it untouched for
kernel 4.19.
This change is currently not run-tested, as i do not have such
a device at hand.
CC: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
CC: André Valentin <avalentin@marcant.net>
CC: WeiDong Jia <jwdsccd@gmail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Tested-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
Daniel Golle [Sun, 22 Mar 2020 13:30:22 +0000 (13:30 +0000)]
oxnas: yet another irqchip related patch
This time DTS fix, again from Sungbo Eo <mans0n@gorani.run>
ARM: dts: oxnas: Fix clear-mask property
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
David Bauer [Sun, 22 Mar 2020 00:34:56 +0000 (01:34 +0100)]
iwinfo: update to latest Git HEAD
9f5a7c4 iwinfo: add missing HT modename for HT-None
06a03c9 Revert "iwinfo: add BSS load element to scan result"
9a4bae8 iwinfo: add device id for Qualcomm Atheros QCA9990
eba5a20 iwinfo: add device id for BCM43602
a6914dc iwinfo: add BSS load element to scan result
bb21698 iwinfo: add device id for Atheros AR9287
7483398 iwinfo: add device id for MediaTek MT7615E
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Thu, 19 Mar 2020 09:33:20 +0000 (10:33 +0100)]
ath79: align Ubiquiti AC Pro ethernet map to factory
The Uniquiti AC Pro and Ubiquiti AC Mesh Pro currently have the
"Primary" and "Secondary" ethernet ports configured to offer LAN as well
as WAN. However, Uiquiti describes the following behavior for the
devices Ethernet ports:
> Secondary UniFi Access Point (UAP) Ethernet ports don't
> provide PoE passthrough (to run current to a second powered
> device), but they do support data passthrough.
> It serves as a bridged interface between main / secondary
> Ethernet port.
To reduce confusion for users (as LAN and WAN functionality is not
visible on the device itself), configure both ports to offer LAN
functionality. Users can still configure a WAN interface on a port they
are able to choose.
CC: Lucian Cristian <lucian.cristian@gmail.com>
Reported-by: Florian Klink <flokli@flokli.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
Robert Marko [Thu, 19 Mar 2020 11:22:07 +0000 (12:22 +0100)]
tools: squashfskit4: fix build with GCC10
In order to build squashfskit with GCC10, this backport from upstream is needed.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[increase PKG_RELEASE]
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Alexander Couzens [Sun, 22 Mar 2020 01:03:19 +0000 (02:03 +0100)]
squashfskit4/Makefile: introduce PKG_RELEASE=1
When adding patches, the PKG_RELEASE should be increased.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Roger Pueyo Centelles [Sun, 15 Mar 2020 17:20:03 +0000 (18:20 +0100)]
ath79: add support for Ubiquiti NanoBridge M (XM)
This patch adds support for the Ubiquiti NanoBridge M (XM), a
802.11n wireless with a feed+dish form factor, with the same board
definition as the Bullet M (XM).
Specifications:
- Atheros AR7241 SoC
- 32 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet port, 24 Vdc PoE-in
- Power and LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1)
Flashing via stock GUI:
- WARNING: flashing OpenWrt from AirOS v5.6 or newer will brick your
device! Read the wiki for more info.
- Downgrade to AirOS v5.5.x (latest available is 5.5.11) first.
- Upload the factory image via AirOS web GUI.
Flashing via TFTP:
- WARNING: flashing OpenWrt from AirOS v5.6 or newer will brick your
device! Read the wiki for more info.
- Downgrade to AirOS v5.5.x (latest available is 5.5.11) first.
- Use a pointy tool (e.g., pen cap, slotted screwdriver) to keep the
reset button pressed.
- Power on the device (keep reset button pressed).
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
LED2+LED4 => LED1+LED3, etc.
- Release reset button.
- The device starts a TFTP server at 192.168.1.20.
- Set a static IP on the computer (e.g., 192.168.1.21/24).
- Upload via tftp the factory image:
$ tftp 192.168.1.20
tftp> bin
tftp> trace
tftp> put openwrt-ath79-generic-xxxxx-ubnt_nanobridge-m-squashfs-factory.bin
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[rebase, fix includes in DTS, add label MAC address, add SOC and
fix sorting in generic-ubnt.mk]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Rafał Miłecki [Mon, 30 Dec 2019 06:54:53 +0000 (07:54 +0100)]
samba36: log error if getting device info failed
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Thu, 20 Feb 2020 12:40:55 +0000 (13:40 +0100)]
bcm53xx: sysupgrade: optimize building UBI image
Use "truncate" to adjust size of existing file instead of "dd" which
required creating a copy. This saves space on tmpfs. It may be as low
as 2.1 MiB when using OpenWrt default user space and way more (20+ MiB)
when flashing vendor firmware.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Thu, 20 Feb 2020 12:40:54 +0000 (13:40 +0100)]
busybox: enable truncate on bcm53xx target
It's needed for optimized sysupgrade. On host machine this change
increased busybox size by 4096 B.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Sungbo Eo [Tue, 10 Mar 2020 13:58:27 +0000 (22:58 +0900)]
treewide: omit IMAGE_SIZE argument from check-size
Now that check-size uses IMAGE_SIZE by default, we can skip the argument from
image recipes to reduce redundancy.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sungbo Eo [Tue, 10 Mar 2020 13:58:00 +0000 (22:58 +0900)]
build: image: set default parameter for check-size
In most cases check-size is used with IMAGE_SIZE and vice versa. Let check-size
use IMAGE_SIZE by default.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Tue, 10 Mar 2020 06:41:09 +0000 (15:41 +0900)]
treewide: gather DEVICE_VARS into one place
Place DEVICE_VARS assignments at the top of the file or above Device/Default
to make them easier to find.
For ramips, remove redundant values already present in parent file.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Russell Senior [Thu, 19 Mar 2020 11:27:28 +0000 (04:27 -0700)]
ath79: add support for ubnt_bullet-m-ar7240 variant
This adds support for the Ubiquiti Bullet M (AR7240).
Specifications:
- AR7240 SoC @ 400 MHz
- 32 MB RAM
- 8 MB SPI flash
- 1x 10/100 Mbps Ethernet, 24 Vdc PoE-in
- External antenna
- POWER/LAN green LEDs
- 4x RSSI LEDs (red, orange, green, green)
- UART (115200 8N1) on PCB
Flashing via WebUI:
Upload the factory image via the stock firmware web UI.
Attention: airOS firmware versions >= 5.6 have a new bootloader with
an incompatible partition table!
Please downgrade to <= 5.5 _before_ flashing OpenWrt!
Refer to the device's Wiki page for further information.
Flashing via TFTP:
Same procedure as other Ubiquiti M boards.
- Use a pointy tool (e.g., pen cap, paper clip) and keep the reset
button on the device or on the PoE supply pressed
- Power on the device via PoE (keep reset button pressed)
- Keep pressing until LEDs flash alternatively LED1+LED3 =>
LED2+LED4 => LED1+LED3, etc.
- Release reset button
- The device starts a TFTP server at 192.168.1.20
- Set a static IP on the computer (e.g., 192.168.1.21/24)
- Upload via tftp the factory image:
$ tftp 192.168.1.20
tftp> bin
tftp> trace
tftp> put openwrt-ath79-generic-xxxxx-ubnt_bullet-m-ar7240-squashfs-factory.bin
The "fixed-link" section of the device tree is needed to avoid errors like this:
Generic PHY mdio.0:1f:04: Master/Slave resolution failed, maybe conflicting manual settings?
With "fixed-link", the errors go away and eth0 comes up reliably.
Signed-off-by: Russell Senior <russell@personaltelco.net>
[fix SUPPORTED_DEVICES]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Linus Walleij [Sat, 21 Mar 2020 13:05:55 +0000 (14:05 +0100)]
gemini: Bump kernel to v5.4
The v5.4 kernel already works much better than v4.19
as so many things got upstreamed so let's just bump
it to kernel v5.4.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Sat, 21 Mar 2020 13:05:54 +0000 (14:05 +0100)]
gemini: Add kernel config for kernel v5.4
This adds a kernel config file for the v5.4 gemini
kernel.
No major changes compared to v4.19, mainly
CONFIG_MTD_PHYSMAP_OF_GEMINI was renamed to
CONFIG_MTD_PHYSMAP_GEMINI.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[select UNWINDER_ARM, set CONFIG_DRM_FBDEV_OVERALLOC, drop
dropped 4.19 symbols, kernel config refreshed]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Linus Walleij [Sat, 21 Mar 2020 13:05:53 +0000 (14:05 +0100)]
gemini: Add v5.4 kernel patches
This adds the kernel patches needed for the Gemini.
Just 7 patches, 5 of them are already upstream.
Notably we incorperate the temperature sensor on the
hard drive to drive temperature control of the NAS
chassis. This is required for the DIR-685 which has
no external temperature sensor.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[use the drivetemp package over the backport]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Sat, 21 Mar 2020 15:39:40 +0000 (16:39 +0100)]
kernel: 5.4: disable more symbols
These have been discovered by the gemini 5.4 patches.
This is because one of the devices uses the FBDEV emulation.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Christian Lamparter [Fri, 28 Feb 2020 22:42:50 +0000 (23:42 +0100)]
kernel: backport and package drivetemp hwmon from v5.5
This patch backports the hwmon drivetemp sensor module from vanilla
linux 5.5 to be available on OpenWrt's 5.4 kernel.
Extract from The upstream commit by Guenter Roeck <linux@roeck-us.net>:
hwmon: Driver for disk and solid state drives with temperature sensors
"Reading the temperature of ATA drives has been supported for years
by userspace tools such as smarttools or hddtemp. The downside of
such tools is that they need to run with super-user privilege, that
the temperatures are not reported by standard tools such as 'sensors'
or 'libsensors', and that drive temperatures are not available for use
in the kernel's thermal subsystem.
This driver solves this problem by adding support for reading the
temperature of ATA drives from the kernel using the hwmon API and
by adding a temperature zone for each drive.
With this driver, the hard disk temperature can be read [...]
using sysfs:
$ grep . /sys/class/hwmon/hwmon9/{name,temp1_input}
/sys/class/hwmon/hwmon9/name:drivetemp
/sys/class/hwmon/hwmon9/temp1_input:23000
If the drive supports SCT transport and reports temperature limits,
those are reported as well.
drivetemp-scsi-0-0
Adapter: SCSI adapter
temp1: +27.0<C2><B0>C (low = +0.0<C2><B0>C, high = +60.0<C2><B0>C)
(crit low = -41.0<C2><B0>C, crit = +85.0<C2><B0>C)
(lowest = +23.0<C2><B0>C, highest = +34.0<C2><B0>C)
The driver attempts to use SCT Command Transport to read the drive
temperature. If the SCT Command Transport feature set is not available,
or if it does not report the drive temperature, drive temperatures may
be readable through SMART attributes. Since SMART attributes are not well
defined, this method is only used as fallback mechanism."
This patch incorperates a patch made by Linus Walleij:
820-libata-Assign-OF-node-to-the-SCSI-device.patch
This patch is necessary in order to wire-up the drivetemp
sensor into the device tree's thermal-zones.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Eneas U de Queiroz [Thu, 19 Mar 2020 19:12:15 +0000 (16:12 -0300)]
openssl: update to 1.1.1e
This version includes bug and security fixes, including medium-severity
CVE-2019-1551, affecting RSA1024, RSA1536, DSA1024 & DH512 on x86_64.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Eneas U de Queiroz [Thu, 19 Mar 2020 19:12:14 +0000 (16:12 -0300)]
openssl: add configuration example for afalg-sync
This adds commented configuration help for the alternate, afalg-sync
engine to /etc/ssl/openssl.cnf.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Daniel Golle [Sat, 21 Mar 2020 14:25:09 +0000 (14:25 +0000)]
oxnas: backport another fix for irqchip
Sungbo Eo <mans0n@gorani.run> submitted another patch fixing an error
on reboot:
irqchip/versatile-fpga: Apply clear-mask earlier
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Paul Spooren [Fri, 20 Mar 2020 10:10:59 +0000 (00:10 -1000)]
scripts: fixup qemustart for new x86 image names
qemustart allows easy testing of created images via `qemu`. The script
automatically selects created images and can setup e.g. networks.
As the x86 target now uses the generic image.mk the profile appears also
in the image name, this is *generic*.
Add the profile name to the qemustart script so it still finds the file.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Paul Spooren [Fri, 20 Mar 2020 10:10:58 +0000 (00:10 -1000)]
x86: allow non gzipped images
The previous image generation code would always gzipped images.
This patch changes the behaviour and only compresses images when
selected in menuconfig.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Paul Spooren [Fri, 20 Mar 2020 10:10:57 +0000 (00:10 -1000)]
x86: use qemu-image command from image-commands.mk
The `qemu-image` command converts images to the specified type and
reduces redundant code.
Adaption from Alexander Couzens <lynxis@fe80.eu> work[0].
[0]: https://git.openwrt.org/?p=openwrt/staging/lynxis.git;a=blob;f=target/linux/x86/image/Makefile;h=
83b8140b7aefbe708fd09c9c61827e7e39bda8b4;hb=
416cccf398e9589e3de386e05b61b1c46cace20d#l51
Signed-off-by: Paul Spooren <mail@aparcar.org>
Paul Spooren [Fri, 20 Mar 2020 10:10:56 +0000 (00:10 -1000)]
x86: remove obsolete legacy profiles
Rely on device profiles instead for packages selection.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[rebase, adjusted commit title]
Signed-off-by: Paul Spooren <mail@aparcar.org>
Paul Spooren [Fri, 20 Mar 2020 10:10:55 +0000 (00:10 -1000)]
x86: switch image generation to new code
This commit introduces few related changes which need to be done in
single commit to keep images buildable between git revisions. In result
it retains all previous image creation possibilities with slight name
change of generated images. Brief summary of the commit:
* Split up image generation recipe to smaller chunks to make it more
generic and reusable.
* Make iso images x86 specific and drop their definition as root
filesystem.
* Convert image creation process to generic code specified in image.mk.
* Make geode subtarget inherit features from the main target instead of
redefining them.
* For subtargets create device definitions with basic packages set.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[rebased]
Signed-off-by: Paul Spooren <mail@aparcar.org>
Paul Spooren [Fri, 20 Mar 2020 10:10:54 +0000 (00:10 -1000)]
x86/grub2: move grub2 image creation to package
Let the grub2 package take care of creating installable grub2 images,
this will allow creating grub2 images without first calling x86 image
generation recipe. Also as side effect, since those images are now
shared, it'll reduce the number of calling grub-mkimage.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[rebase, adjusted commit title]
Signed-off-by: Paul Spooren <mail@aparcar.org>
Kevin Darbyshire-Bryant [Sat, 21 Mar 2020 09:25:49 +0000 (09:25 +0000)]
kernel: connmark set-dscpmark fix build on 5.4
Fix header change that was done for kernel but 4.19 got missed for 5.4.
Solves nasty errors like:
8.4.0_musl/include/linux/netfilter/xt_CONNMARK.h:5,
from connmark_listener.c:30:
/builder/shared-workdir/build/sdk/staging_dir/toolchain-aarch64_cortex-a53_gcc-8.4.0_musl/include/linux/netfilter/xt_connmark.h:23:2: error: enumerator value for 'XT_CONNMARK_VALUE' is not an integer constant
XT_CONNMARK_VALUE = BIT(0),
^~~~~~~~~~~~~~~~~
/builder/shared-workdir/build/sdk/staging_dir/toolchain-aarch64_cortex-a53_gcc-8.4.0_musl/include/linux/netfilter/xt_connmark.h:25:1: error: enumerator value for 'XT_CONNMARK_DSCP' is not an integer constant
};
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Jason A. Donenfeld [Sat, 21 Mar 2020 02:12:53 +0000 (20:12 -0600)]
wireguard: bump to 0.0.
20200318
WireGuard had a brief professional security audit. The auditors didn't find
any vulnerabilities, but they did suggest one defense-in-depth suggestion to
protect against potential API misuse down the road, mentioned below. This
compat snapshot corresponds with the patches I just pushed to Dave for
5.6-rc7.
* curve25519-x86_64: avoid use of r12
This buys us 100 extra cycles, which isn't much, but it winds up being even
faster on PaX kernels, which use r12 as a RAP register.
* wireguard: queueing: account for skb->protocol==0
This is the defense-in-depth change. We deal with skb->protocol==0 just fine,
but the advice to deal explicitly with it seems like a good idea.
* receive: remove dead code from default packet type case
A default case of a particular switch statement should never be hit, so
instead of printing a pretty debug message there, we full-on WARN(), so that
we get bug reports.
* noise: error out precomputed DH during handshake rather than config
All peer keys will now be addable, even if they're low order. However, no
handshake messages will be produced successfully. This is a more consistent
behavior with other low order keys, where the handshake just won't complete if
they're being used anywhere.
* send: use normaler alignment formula from upstream
We're trying to keep a minimal delta with upstream for the compat backport.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Jason A. Donenfeld [Sat, 21 Mar 2020 02:12:17 +0000 (20:12 -0600)]
wireguard-tools: bump to 1.0.
20200319
* netlink: initialize mostly unused field
* curve25519: squelch warnings on clang
Code quality improvements.
* man: fix grammar in wg(8) and wg-quick(8)
* man: backlink wg-quick(8) in wg(8)
* man: add a warning to the SaveConfig description
Man page improvements. We hope to rewrite our man pages in mdocml at some
point soon.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Chuanhong Guo [Fri, 20 Mar 2020 12:58:49 +0000 (20:58 +0800)]
mediatek: move mt76 and wpad-bacic to mt7622 subtarget
mt76 is a target default package for mt7622-wmac only.
mt7623 doesn't have integrated wireless support and wifi drivers for
pcie cards should be added as device specific package.
mt7629-wmac isn't supported by mt76 yet.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Fri, 20 Mar 2020 11:36:30 +0000 (19:36 +0800)]
mediatek: mt7629: fix firmware partition
rename "kernel" partition in upstream dts to "firmware" and add
denx,fit as compatible string for mtdsplit.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Fri, 20 Mar 2020 11:26:45 +0000 (19:26 +0800)]
mediatek: backport spi-mem based mtk spinor driver
This new driver has full quadspi and DMA support, providing way better
reading performance.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Fri, 20 Mar 2020 11:23:01 +0000 (19:23 +0800)]
mediatek: mt7629: refresh config for linux 5.4
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Fri, 20 Mar 2020 10:08:00 +0000 (18:08 +0800)]
mediatek: mt7629: fix ethernet default config
1. fix typo: ucidef_set_interfaces_wan -> ucidef_set_interface_wan
2. change board name to mt7629-rfb to match upstream dts
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Luiz Angelo Daros de Luca [Sat, 1 Feb 2020 03:51:59 +0000 (00:51 -0300)]
kernel: load rtl8366_smi and rtl8367b on boot
This external switch driver should be loaded on boot for network support
in failsafe mode.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
[alter commit message]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Serge Vasilugin [Mon, 16 Mar 2020 08:28:38 +0000 (16:28 +0800)]
kernel: rtl8367b: add configuration for extif2
Both rtl8367b and rtl8367s have two extended interface
rtl8367rb: 5 port + 2*RGMII/MII
rtl8367s: 5 port + SGMII/HSGMI + RGMII/MII
(?)rtl8367sb: 5 port + 2*RGMII/MII
These interfaces correspond to EXT1 and EXT2 (ports 6 and 7 respectivly).
This patch allow to configure EXT2 in dts-file:
rtl8367rb {
compatible = "realtek,rtl8367b";
cpu_port = <7>;
realtek,extif2 = <1 0 1 1 1 1 1 1 2>;
mii-bus = <&mdio0>;
phy_id = <29>;
};
Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru>
[fix indent, replace magic value, alter commit message]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Chuanhong Guo [Mon, 16 Mar 2020 08:04:09 +0000 (16:04 +0800)]
generic: rtl8367b: add definition of debug reg
This commit adds definition of DEBUG0 and DEBUG1 registers and replace
magic values with proper register modifying.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Oldřich Jedlička [Mon, 16 Mar 2020 20:00:51 +0000 (21:00 +0100)]
mac80211: do not try to setup hostapd-managed interfaces.
For virtual access points (when multiple SSIDs are used for one
physical AP), there exist one physical network interface and
multiple virtual interfaces, which are fully under control of
hostapd. When networking is setup, the script
`/lib/netifd/wireless/mac80211.sh` is called, which tries to bring
the interface up by a call to `ip link set dev <iface> up`. This
call might fail for virtual APs, because the virtual interface
might not have been created by hostapd yet. There are some artifical
delays in the script most probably to handle this, but when DFS
channel availability check on 5GHz band is issued, hostapd can
delay creating virtual interfaces by a minute.
In order to fix this (or work around it), do not try to bring the
interface up (this is responsibility of hostapd anyway) and
do not try to set txpower on the virtual interface.
Fixes FS#2698.
Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
Chen Minqiang [Thu, 11 Jul 2019 14:34:03 +0000 (22:34 +0800)]
x86: make crashdump works
1. KERNEL_CRASH_DUMP should depends on KERNEL_PROC_KCORE (kexec use it)
2. select crashkernel mem size by totalmem
mem <= 256M disable crashkernel by default
mem >= 4G use 256M for crashkernel
mem >= 8G use 512M for crashkernel
default use 128M
3. set BOOT_IMAGE in kdump.init
4. resolve a "Unhandled rela relocation: R_X86_64_PLT32" error
Tested on x86_64
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Jan Kardell [Fri, 20 Mar 2020 13:32:23 +0000 (14:32 +0100)]
readline: needs host depend on ncurses to build
We must ensure that host ncurses is build before host readline.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
projects / openwrt / staging / aparcar.git / log