drm/bridge: analogix_dp: Move enable video into config_video()

We need to enable video before analogix_dp_is_video_stream_on(), so
we can get the right video stream status.

We needed to increase the delay in the timeout loop because there is
random "Timeout of video streamclk ok" message happen when debug edp
panel, this time do not define in the spec.

Cc: 征增 王 <wzz@rock-chips.com>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-2-enric.balletbo@collabora.com

drm/vc4: Add CTM registers to debugfs

Now that we set the OLED* registers to do CTM, it's helpful to have them
in the register dump.

Signed-off-by: Stefan Schake <stschake@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20180420122545.40014-2-stschake@gmail.com

drm/vc4: Add CTM support

The hardware has a single block for applying a CTM prior to gamma lut.
It can be fed with pixels from one of our CRTC at a time and uses a
matrix with S0.9 scalars. Use private atomic state to reject attempts
from userland to apply CTM for more than one CRTC at a time and reject
matrices with scalars that we can't approximate without integer bits.

Signed-off-by: Stefan Schake <stschake@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/218067/

drm/vc4: Add support for plane alpha

The HVS supports mixing fixed alpha with per-pixel alpha or
setting a fixed plane alpha in case there is no per-pixel information.
This allows us to support the generic DRM plane alpha property.

Signed-off-by: Stefan Schake <stschake@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20180421000954.18936-1-stschake@gmail.com

gpu: drm: vc4: simplify getting .drvdata

We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20180419140641.27926-17-wsa+renesas@sang-engineering.com

dt-bindings: drm/bridge: Document Cadence DSI bridge bindings

Document the bindings used for the Cadence DSI bridge.

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180421070846.10330-2-boris.brezillon@bootlin.com

drm/bridge: Add Cadence DSI driver

Add a driver for Cadence DPI -> DSI bridge.

This driver only support a subset of Cadence DSI bridge capabilities.

This driver has been tested/debugged in a simulated environment which
explains why some of the features are missing.  Here is a
non-exhaustive list of missing features:
 * burst mode
 * DPHY init/configuration steps
 * support for additional input interfaces (SDI input)

DSI commands and non-burst video mode have been tested.

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180421070846.10330-1-boris.brezillon@bootlin.com

drm: dw-hdmi-i2s: Remove owner assignment from platform_driver

platform_driver does not need to set the owner field, as this will
be populated by the driver core.

Generated by scripts/coccinelle/api/platform_no_drv_owner.cocci.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1521137057-14773-1-git-send-email-festevam@gmail.com

drm: bridge: Add thc63lvd1024 LVDS decoder driver

Add DRM bridge driver for Thine THC63LVD1024 LVDS to digital parallel
output converter.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1524062429-325-3-git-send-email-jacopo+renesas@jmondi.org

dt-bindings: display: bridge: Document THC63LVD1024 LVDS decoder

Document Thine THC63LVD1024 LVDS decoder device tree bindings.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1524062429-325-2-git-send-email-jacopo+renesas@jmondi.org
Link: https://patchwork.freedesktop.org/patch/msgid/1524062429-325-2-git-send-email-jacopo+renesas@jmondi.org

drm/bridge/synopsys: dsi: Adopt SPDX identifiers

Add SPDX identifiers to the Synopsys DesignWare MIPI DSI
host controller driver.

Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Acked-by: Philippe Ombredanne <pombredanne@nexB.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180208145805.24762-1-philippe.cornu@st.com

drm/stm: ltdc: fix warning in ltdc_crtc_update_clut()

Fix the warning
"warn: variable dereferenced before check 'crtc' (see line 390)"
by removing unnecessary checks as ltdc_crtc_update_clut() is
only called from ltdc_crtc_atomic_flush() where crtc and
crtc->state are not NULL.

Many thanks to Dan Carpenter for the bug report
https://lists.freedesktop.org/archives/dri-devel/2018-February/166918.html

Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: yannick fertre <yannick.fertre@st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180410135312.3553-1-philippe.cornu@st.com

drm/stm: ltdc: add user update info in plane print state

This patch adds the user update information in
frames-per-second into the drm debugfs plane state.

Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180407213503.30932-1-philippe.cornu@st.com

drm/stm: move enable/disable_vblank to crtc

enable/disable_vblank() functions at drm_driver level
are deprecated. Move them to the ltdc drm_crtc_funcs
structure.

Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180407212937.30407-1-philippe.cornu@st.com

drm/xen-front: Remove CMA support

It turns out this was only needed to paper over a bug in the CMA
helpers, which was addressed in

commit 998fb1a0f478b83492220ff79583bf9ad538bdd8
Author: Liviu Dudau <Liviu.Dudau@arm.com>
Date:   Fri Nov 10 13:33:10 2017 +0000

    drm: gem_cma_helper.c: Allow importing of contiguous scatterlists with nents > 1

Without this the following pipeline didn't work:

domU:
1. xen-front allocates a non-contig buffer
2. creates grants out of it

dom0:
3. converts the grants into a dma-buf. Since they're non-contig, the
scatter-list is huge.
4. imports it into rcar-du, which requires dma-contig memory for
scanout.

-> On this given platform there's an IOMMU, so in theory this should
work. But in practice this failed, because of the huge number of sg
entries, even though the IOMMU driver mapped it all into a dma-contig
range.

With a guest-contig buffer allocated in step 1, this problem doesn't
exist. But there's technically no reason to require guest-contig
memory for xen buffer sharing using grants.

Given all that, the xen-front cma support is not needed and should be
removed.

Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180417074012.21311-1-andr2000@gmail.com

drm/atomic: Add sanity checks to drm_atomic_helper_async_commit()

->atomic_async_update() requires that drivers update the plane->state
object before returning. Make sure at least common properties have been
updated.

Cc: Gustavo Padovan <gustavo@padovan.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180330145518.29770-1-boris.brezillon@bootlin.com

drm/vc4: update cursors asynchronously through atomic

Add support for async updates of cursors by using the new atomic
interface for that. Basically what this commit does is do what
vc4_update_plane() did but through atomic.

v7: Place the drm_atomic_set_fb_for_plane() call after the new
    FB has been applied to the HW to avoid possible use-after-free
    issues
v6: add missing drm_atomic_set_fb_for_plane() in
    vc4_plane_atomic_async_update() (Boris Brezillon)
v5: add missing call to vc4_plane_atomic_check() (Eric Anholt)
v4: add drm_atomic_helper_async() commit (Eric Anholt)
v3: move size checks back to drivers (Ville Syrjälä)
v2: move fb setting to core and use new state (Eric Anholt)

Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180330085445.31726-1-boris.brezillon@bootlin.com

drm/vc4: Move CRTC state to header

We need to access the channel for configuring our CTM hardware.

Signed-off-by: Stefan Schake <stschake@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/1523479755-20812-4-git-send-email-stschake@gmail.com

drm/vc4: Expose gamma as atomic property

We are an atomic driver so the gamma LUT should also be exposed as a
CRTC property through the DRM atomic color management. This will also
take care of the legacy path for us.

Signed-off-by: Stefan Schake <stschake@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/1523479755-20812-3-git-send-email-stschake@gmail.com

drm/vc4: Add some missing HVS register definitions.

At least the RGBA expand field we should have been setting, because we
aren't expanding correctly for 565 -> 8888.  Other registers are ones
that may be interesting for various projects that have been discussed.

Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Schake <stschake@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1523479755-20812-2-git-send-email-stschake@gmail.com

drm/rockchip: fix VOP vblank race

We have seen a case of a bad reference count for vblanks with the
Rockchip VOP:

------------[ cut here ]------------
WARNING: CPU: 1 PID: 383 at drivers/gpu/drm/drm_irq.c:1198 drm_vblank_put+0x40/0xcc
Modules linked in: brcmfmac brcmutil
CPU: 1 PID: 383 Comm: kworker/u8:2 Not tainted 4.9.75-rt60 #1
Hardware name: Rockchip (Device Tree)
Workqueue: events_unbound flip_worker
Backtrace:
[<c010b7b0>] (dump_backtrace) from [<c010ba4c>] (show_stack+0x18/0x1c)
 r7:c0b1b13c r6:600b0013 r5:00000000 r4:c0b1b13c
[<c010ba34>] (show_stack) from [<c032d248>] (dump_stack+0x78/0x94)
[<c032d1d0>] (dump_stack) from [<c011e6e8>] (__warn+0xe4/0x104)
 r7:00000009 r6:c03cf26c r5:00000000 r4:00000000
[<c011e604>] (__warn) from [<c011e7c0>] (warn_slowpath_null+0x28/0x30)
 r9:eeb443a0 r8:eeb443c8 r7:ee8a5ec0 r6:ee8a5ec0 r5:edb47f00 r4:ee096200
[<c011e798>] (warn_slowpath_null) from [<c03cf26c>] (drm_vblank_put+0x40/0xcc)
[<c03cf22c>] (drm_vblank_put) from [<c03cf310>] (drm_crtc_vblank_put+0x18/0x1c)
 r5:edb47f00 r4:ee3c8a80
[<c03cf2f8>] (drm_crtc_vblank_put) from [<c03ef9b4>] (vop_fb_unref_worker+0x18/0x24)
[<c03ef99c>] (vop_fb_unref_worker) from [<c03df194>] (flip_worker+0x98/0xb4)
 r5:edb47f00 r4:eeb443a8
[<c03df0fc>] (flip_worker) from [<c0134808>] (process_one_work+0x1a8/0x2fc)
 r9:00000000 r8:ee807d00 r7:00000000 r6:ee809c00 r5:eeb443a8 r4:edfe5f80
[<c0134660>] (process_one_work) from [<c01358ec>] (worker_thread+0x2ac/0x458)
 r10:00000088 r9:edfe5f98 r8:ee809c2c r7:c0b04100 r6:ee809c00 r5:ee809c00
 r4:edfe5f80
[<c0135640>] (worker_thread) from [<c013a0bc>] (kthread+0xfc/0x10c)
 r10:00000000 r9:00000000 r8:c0135640 r7:edfe5f80 r6:00000000 r5:edf0e240
 r4:ee8a4000 r3:ed194e00
[<c0139fc0>] (kthread) from [<c0107cb8>] (ret_from_fork+0x14/0x3c)
 r8:00000000 r7:00000000 r6:00000000 r5:c0139fc0 r4:edf0e240
---[ end trace 0000000000000002 ]---

It seems that this is caused by unfortunate timing between
vop_crtc_atomic_flush() and vop_handle_vblank() given the following
ordering:

atomic_flush handle_vblank
------------ -------------

drm_flip_work_queue
set_bit
      if (test_and_clear_bit(...))
      drm_flip_work_commit
drm_vblank_get

This results in vop_fb_unref_worker (called as flip work) decrementing
the vblank refcount before it has been incremented.

Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Sandy huang <hjc@rock-chips.com>
Signed-off-by: Sandy Huang <hjc@rock-chips.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328160351.23763-1-john@metanate.com

drm/docs: Remove the rcar alpha from the csv file

Now that we moved the rcar-du DRM driver has been switched to the generic
alpha property, remove the former property documentation from the
deprecated CSV file.

Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/04be5e2256aa8d33d9521a68a10f0b73a24f8040.1523432341.git-series.maxime.ripard@bootlin.com

drm/sun4i: Add support for plane alpha

Our backend supports a per-plane alpha property. Support it through our new
helper.

Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/13e89f0d2f2b55752a22eb8c4f37f325246a3a9c.1523432341.git-series.maxime.ripard@bootlin.com

drm/rcar-du: Convert to the new generic alpha property

Now that we have support for per-plane alpha in the core, let's use it.

Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a343697b87109cd8d9675ea8bce2e561051a696f.1523432341.git-series.maxime.ripard@bootlin.com

drm/atmel-hclcdc: Convert to the new generic alpha property

Now that we have support for per-plane alpha in the core, let's use it.

Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/e5e97e2aae129600233e0983b748e4ba51ced239.1523432341.git-series.maxime.ripard@bootlin.com

drm/blend: Add a generic alpha property

Some drivers duplicate the logic to create a property to store a per-plane
alpha.

This is especially useful if we ever want to support extra protocols for
Wayland like:
https://lists.freedesktop.org/archives/wayland-devel/2017-August/034741.html

Let's create a helper in order to move that to the core.

Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6e1ce0db78fcfc407e94913c64819e65109d034d.1523432341.git-series.maxime.ripard@bootlin.com

drm/sun4i: Tie the DSI controller in the TCON

The DSI controller needs a particular interface (CPU aka 8080) with some
modifications from the TCON in order to run.

Make sure the TCON is able to provide it when we are using the DSI output.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/129f5928113d2ca865bf5269047c2e4ba6fed5e6.1522835818.git-series.maxime.ripard@bootlin.com

drm/sun4i: Add Allwinner A31 MIPI-DSI controller support

Most of the Allwinner SoCs since the A31 share the same MIPI-DSI
controller.

While that controller is mostly undocumented, the code is out there and has
been cleaned up in order to be integrated into DRM. However, there's still
some dark areas that are a bit unclear about how the block exactly
operates.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ad9e6224fced87c0889ddd2765d1942610061f72.1522835818.git-series.maxime.ripard@bootlin.com

dt-bindings: display: Add Allwinner MIPI-DSI bindings

The Allwinner SoCs usually come with a DSI encoder. Add a binding for it.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/cdc5402570199f5c08211f29d9182ea5948d3c40.1522835818.git-series.maxime.ripard@bootlin.com

drm/sun4i: tcon: Add TRI finish interrupt for vblank

The "CPU" (or Intel 8080) interface uses a different interrupt called
TRI_FINISH (most likely TRI being for trigger) to notify the end of frames,
and hence the VBLANK period.

And that interrupt to the possible VBLANK interrupts source.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/de6d6ad8959da77ea3a974a31a4c0c8391178748.1522835818.git-series.maxime.ripard@bootlin.com

Merge tag 'mmio-clk-config' of https://git./linux/kernel/git/broonie/regmap into drm-misc-next

regmap: MMIO regmap clock configuration

This patch provides a mechanism for specifying a different clock to be
used with the regmap clock integration.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180226131207.GB6681@sirena.org.uk

drm/sti: Depend on OF rather than selecting it

Commit cc6b741c6f63 ("drm: sti: remove useless fields from vtg
structure") reworked some code inside of this driver and made it select
CONFIG_OF. This results in the entire OF layer being enabled when
building an allmodconfig on ia64. OF on ia64 is completely unsupported
so this isn't a great state of affairs.

The 0day robot noticed a link-time failure on ia64 caused by
using of_node_to_nid() in an otherwise unrelated driver. The
generic fallback for of_node_to_nid() only exists when:

defined(CONFIG_OF) && defined(CONFIG_NUMA) == false

Since CONFIG_NUMA is usually selected for IA64 we get the link failure.
Fix this by making the driver depend on OF rather than selecting it,
odds are that was the original intent.

Link: https://lists.01.org/pipermail/kbuild-all/2018-March/045172.html
Fixes: cc6b741c6f63 ("drm: sti: remove useless fields from vtg structure")
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-ia64@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180403053401.30045-1-oohall@gmail.com

MAINTAINERS: Add drm/xen-front maintainer entry

Add myself as drivers/gpu/drm/xen maintainer.

Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180403123238.19294-1-andr2000@gmail.com

drm/xen-front: Add support for Xen PV display frontend

Add support for Xen para-virtualized frontend display driver.
Accompanying backend [1] is implemented as a user-space application
and its helper library [2], capable of running as a Weston client
or DRM master.
Configuration of both backend and frontend is done via
Xen guest domain configuration options [3].

Driver limitations:
 1. Only primary plane without additional properties is supported.
 2. Only one video mode supported which resolution is configured
    via XenStore.
 3. All CRTCs operate at fixed frequency of 60Hz.

1. Implement Xen bus state machine for the frontend driver according to
the state diagram and recovery flow from display para-virtualized
protocol: xen/interface/io/displif.h.

2. Read configuration values from Xen store according
to xen/interface/io/displif.h protocol:
  - read connector(s) configuration
  - read buffer allocation mode (backend/frontend)

3. Handle Xen event channels:
  - create for all configured connectors and publish
    corresponding ring references and event channels in Xen store,
    so backend can connect
  - implement event channels interrupt handlers
  - create and destroy event channels with respect to Xen bus state

4. Implement shared buffer handling according to the
para-virtualized display device protocol at xen/interface/io/displif.h:
  - handle page directories according to displif protocol:
    - allocate and share page directories
    - grant references to the required set of pages for the
      page directory
  - allocate xen balllooned pages via Xen balloon driver
    with alloc_xenballooned_pages/free_xenballooned_pages
  - grant references to the required set of pages for the
    shared buffer itself
  - implement pages map/unmap for the buffers allocated by the
    backend (gnttab_map_refs/gnttab_unmap_refs)

5. Implement kernel modesetiing/connector handling using
DRM simple KMS helper pipeline:

- implement KMS part of the driver with the help of DRM
  simple pipepline helper which is possible due to the fact
  that the para-virtualized driver only supports a single
  (primary) plane:
  - initialize connectors according to XenStore configuration
  - handle frame done events from the backend
  - create and destroy frame buffers and propagate those
    to the backend
  - propagate set/reset mode configuration to the backend on display
    enable/disable callbacks
  - send page flip request to the backend and implement logic for
    reporting backend IO errors on prepare fb callback

- implement virtual connector handling:
  - support only pixel formats suitable for single plane modes
  - make sure the connector is always connected
  - support a single video mode as per para-virtualized driver
    configuration

6. Implement GEM handling depending on driver mode of operation:
depending on the requirements for the para-virtualized environment,
namely requirements dictated by the accompanying DRM/(v)GPU drivers
running in both host and guest environments, number of operating
modes of para-virtualized display driver are supported:
 - display buffers can be allocated by either
   frontend driver or backend
 - display buffers can be allocated to be contiguous
   in memory or not

Note! Frontend driver itself has no dependency on contiguous memory for
its operation.

6.1. Buffers allocated by the frontend driver.

The below modes of operation are configured at compile-time via
frontend driver's kernel configuration.

6.1.1. Front driver configured to use GEM CMA helpers
     This use-case is useful when used with accompanying DRM/vGPU driver
     in guest domain which was designed to only work with contiguous
     buffers, e.g. DRM driver based on GEM CMA helpers: such drivers can
     only import contiguous PRIME buffers, thus requiring frontend driver
     to provide such. In order to implement this mode of operation
     para-virtualized frontend driver can be configured to use
     GEM CMA helpers.

6.1.2. Front driver doesn't use GEM CMA
     If accompanying drivers can cope with non-contiguous memory then, to
     lower pressure on CMA subsystem of the kernel, driver can allocate
     buffers from system memory.

Note! If used with accompanying DRM/(v)GPU drivers this mode of operation
may require IOMMU support on the platform, so accompanying DRM/vGPU
hardware can still reach display buffer memory while importing PRIME
buffers from the frontend driver.

6.2. Buffers allocated by the backend

This mode of operation is run-time configured via guest domain
configuration through XenStore entries.

For systems which do not provide IOMMU support, but having specific
requirements for display buffers it is possible to allocate such buffers
at backend side and share those with the frontend.
For example, if host domain is 1:1 mapped and has DRM/GPU hardware
expecting physically contiguous memory, this allows implementing
zero-copying use-cases.

Note, while using this scenario the following should be considered:
  a) If guest domain dies then pages/grants received from the backend
     cannot be claimed back
  b) Misbehaving guest may send too many requests to the
     backend exhausting its grant references and memory
     (consider this from security POV).

Note! Configuration options 1.1 (contiguous display buffers) and 2
(backend allocated buffers) are not supported at the same time.

7. Handle communication with the backend:
 - send requests and wait for the responses according
   to the displif protocol
 - serialize access to the communication channel
 - time-out used for backend communication is set to 3000 ms
 - manage display buffers shared with the backend

[1] https://github.com/xen-troops/displ_be
[2] https://github.com/xen-troops/libxenbe
[3] https://xenbits.xen.org/gitweb/?p=xen.git;a=blob;f=docs/man/xl.cfg.pod.5.in;h=a699367779e2ae1212ff8f638eff0206ec1a1cc9;hb=refs/heads/master#l1257

Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180403112317.28751-2-andr2000@gmail.com

drm: Reshuffle getfb error returns

Make it a little more clear what's going on inside of getfb, and also
make it easier to add alternate paths to get a handle in future.

Signed-off-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180323134553.15993-3-daniels@collabora.com

Merge airlied/drm-next into drm-misc-next

Backmerging to pick up a fix from drm-misc-next-fixes.

Signed-off-by: Sean Paul <seanpaul@chromium.org>

drm/i915: Make force_load_detect effective even w/ DMI quirks/hotplug

When doing forced load detection testing we should totally ignore any
hotplug status for the connector. This is mostly relevant for machines
where we already ignore the hotplug status based on the DMI quirks. On
other machines we would currently skip the force load detection tests
on account of the connector already being connected.

v2: Drop the other force_load_detect check since it's useless now (Maarten)

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322174135.5982-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: Restore planes after load detection

Actually turn the planes back on after were done with
the load detection.

Fixes: 20bdc112bbe4 ("drm/i915: Disable all planes for load detection, v2.")
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322152313.6561-23-ville.syrjala@linux.intel.com

drm/zte: Stop consulting plane->crtc

We want to get rid of plane->crtc on atomic drivers. Stop looking at it.

v2: Use old_state->crtc (Maarten)
v3: s/fb/crtc/ in commit message to actually match the patch (Shawn)

Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180326121442.32009-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/vmwgfx: Stop consulting plane->fb

We want to get rid of plane->fb on atomic drivers. Stop looking at it.

Cc: VMware Graphics <linux-graphics-maintainer@vmware.com>
Cc: Sinclair Yeh <syeh@vmware.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322152313.6561-13-ville.syrjala@linux.intel.com
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/sti: Stop consulting plane->fb

We want to get rid of plane->fb on atomic drivers. Stop looking at it.

Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322152313.6561-12-ville.syrjala@linux.intel.com
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/i915: Stop consulting plane->fb

We want to get rid of plane->fb on atomic drivers. Stop looking at it.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322152313.6561-10-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm: Use plane->state->fb over plane->fb

Stop looking at plane->fb on atomic drivers. Use plane->state->fb
instead.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322152313.6561-9-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm: Make the fb refcount handover less magic

Instead of assigning the plane->fb pointer and clearing the fb pointer
to hand over the reference, let's just do it by grabbing another
referece for plane->fb and let fb keep its original one.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322152313.6561-8-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm: Adjust whitespace for legibility

Add a bit of whitespace here and there to make the code look a bit
more structured.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322152313.6561-7-ville.syrjala@linux.intel.com
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm: Add local 'plane' variable for primary/cursor planes

Make the code a bit more readable by storing the plane pointer in a
local variable rather than having to do crtc->{primary,cursor} all the
time.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322152313.6561-6-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/atomic-helper: WARN if legacy plane fb pointers are bogus when committing duplicated state

drm_atomic_helper_commit_duplicated_state() should only be called
resume/reset/load_detect paths where plane->old_fb should always be
NULL and plane->fb should be equal to the new_plane_state->fb.
Assert that is indeed the case.

Cc: martin.peres@free.fr
Cc: chris@chris-wilson.co.uk
Cc: Dave Airlie <airlied@gmail.com> (v1)
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322152313.6561-5-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm: Clear crtc->primary->crtc when disabling the crtc via setcrtc()

Keep the primary->crtc in sync with the state->crtc (also with
primary->fb and state->fb) when disabling the crtc (and thus also
the primary) via setcrtc().

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322152313.6561-4-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/atomic-helper: Drop plane->fb references only for drm_atomic_helper_shutdown()

drm_atomic_helper_shutdown() needs to release the reference held by
plane->fb. Since commit 49d70aeaeca8 ("drm/atomic-helper: Fix leak in
disable_all") we're doing that by calling drm_atomic_clean_old_fb() in
drm_atomic_helper_disable_all(). This also leaves plane->fb == NULL
afterwards. However, since drm_atomic_helper_disable_all() is also
used by the i915 gpu reset code
drm_atomic_helper_commit_duplicated_state() then has to undo the
damage and put the correct plane->fb pointers back in (and also
adjust the ref counts to match again as well).

That approach doesn't work so well for load detection as nothing
sets up the plane->old_fb pointers for us. This causes us to
leak an extra reference for each plane->fb when
drm_atomic_helper_commit_duplicated_state() calls
drm_atomic_clean_old_fb() after load detection.

To fix this let's call drm_atomic_clean_old_fb() only for
drm_atomic_helper_shutdown() as that's the only time we need to
actually drop the plane->fb references. In all the other cases
(load detection, gpu reset) we want to leave plane->fb alone.

v2: Don't inflict the clean_old_fbs bool to drivers (Daniel)
v3: Squash in the revert and rewrite the commit msg (Daniel)

Cc: martin.peres@free.fr
Cc: chris@chris-wilson.co.uk
Cc: Dave Airlie <airlied@gmail.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322152313.6561-3-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #pre-squash
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm: Use srcu to protect drm_device.unplugged

Use srcu to protect drm_device.unplugged in a race free manner.
Drivers can use drm_dev_enter()/drm_dev_exit() to protect and mark
sections preventing access to device resources that are not available
after the device is gone.

Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Reviewed-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Tested-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Cc: intel-gfx@lists.freedesktop.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1522222715-11814-1-git-send-email-andr2000@gmail.com

Merge branch 'drm-misc-next-fixes' of git://anongit.freedesktop.org/drm/drm-misc into drm-next

- Mask mode type garbage from userspace (Ville)

Something went wrong on the misc tree side, but I'll pull the patch directly.

* 'drm-misc-next-fixes' of git://anongit.freedesktop.org/drm/drm-misc:
  drm: Fix uabi regression by allowing garbage mode->type from userspace

drm: add parameter explanation for some gem dmabuf_ops

To reduce some warnings.

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Samuel Li <Samuel.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1522092145-12645-1-git-send-email-Samuel.Li@amd.com

drm/tinydrm: Make fb_dirty into a lower level hook

mipi_dbi_enable_flush() wants to call the fb->dirty() hook from the
bowels of the .atomic_enable() hook. That prevents us from taking the
plane mutex in fb->dirty() unless we also plumb down the acquire
context.

Instead it seems simpler to split the fb->dirty() into a tinydrm
specific lower level hook that can be called from
mipi_dbi_enable_flush() and from a generic higher level
tinydrm_fb_dirty() helper. As we don't have a tinydrm specific
vfuncs table we'll just stick it into tinydrm_device directly
for now.

v2: Deal with the fb->dirty() in tinydrm_display_pipe_update() as well (Noralf)

Cc: "Noralf Trønnes" <noralf@tronnes.org>
Cc: David Lechner <david@lechnology.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180323153509.15287-1-ville.syrjala@linux.intel.com
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Tested-by: Noralf Trønnes <noralf@tronnes.org>

drm/simple-kms-helper: Plumb plane state to the enable hook

tinydrm enable hook wants to play around with the new fb in
.atomic_enable(), thus we'll need access to the plane state.

Performed with coccinelle:
@r1@
identifier F =~ ".*enable$";
identifier P, CS;
@@
F(
struct drm_simple_display_pipe *P
,struct drm_crtc_state *CS
+ ,struct drm_plane_state *plane_state
)
{
...
}

@@
struct drm_simple_display_pipe *P;
expression E;
@@
{
+ struct drm_plane *plane;
...
+ plane = &P->plane;
P->funcs->enable(P
,E
+ ,plane->state
);
...
}

@@
identifier P, CS;
@@
struct drm_simple_display_pipe_funcs {
...
        void (*enable)(struct drm_simple_display_pipe *P
      ,struct drm_crtc_state *CS
+ ,struct drm_plane_state *plane_state
);
...
};

v2: Pimp the commit message (David)

Cc: Marek Vasut <marex@denx.de>
Cc: Eric Anholt <eric@anholt.net>
Cc: David Lechner <david@lechnology.com>
Cc: "Noralf Trønnes" <noralf@tronnes.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322202738.25817-1-ville.syrjala@linux.intel.com
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>

drm/udl: Get rid of dev->struct_mutex usage

It's only used to protect our page list, and only when we know we have
a full reference. This means none of these code paths can ever race
with the final unref, and hence we do not need dev->struct_mutex
serialization and can simply switch to our own locking.

For more context the only magic the locked gem_free_object provides is
that it prevents concurrent final unref (and destruction) of gem
objects while anyone is holding dev->struct_mutex. This was used by
i915 (and other drivers) to implement eviction handling with less
headaches.

Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180327082356.24516-3-daniel.vetter@ffwll.ch

drm/rockchip: fixup comment for gem_free_object_unlocked

Just want to clean out all grep hits. gem_free_object is deprecated.

Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Sandy Huang <hjc@rock-chips.com>
Cc: "Heiko Stübner" <heiko@sntech.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180327082356.24516-2-daniel.vetter@ffwll.ch

staging/vboxvideo: Use gem_free_object_unlocked

vboxvideo doesn't use dev->struct_mutex and therefore has no need to use
gem_free_object.

Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Michael Thayer <michael.thayer@oracle.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180327082356.24516-1-daniel.vetter@ffwll.ch

drm/omap: Use normalized zpos for plane placement

Planes with identical zpos value will result undefined behavior:
disappearing planes, screen flickering and it is not supported by the
hardware.

Use normalized zpos to make sure that we don't encounter invalid
configuration.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180321102029.15248-7-peter.ujfalusi@ti.com

drm: rcar-du: Let core take care of normalizing the zpos

Set the drm_mode_config->normalize_zpos and call drm_atomic_helper_check()
from rcar_du_atomic_check() instead of re implementing the function locally.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180321102029.15248-6-peter.ujfalusi@ti.com

drm/sti: Let core take care of normalizing the zpos

Instead of re-implementing the drm_atomic_helper_check() locally with just
adding drm_atomic_normalize_zpos() into it, set the
drm_mode_config->normalize_zpos.

Note: the drm_atomic_helper_check() now includes

if (state->legacy_cursor_update)
state->async_update = !drm_atomic_helper_async_check(drm, state);

which was added after the driver moved away from using it
(38d868e41c4b9250d5a115c049dc2d48f4909581 drm: Don't force all planes to
be added to the state due to zpos)

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Benjamin Gaignard <benjamin.gaignard@linaro.org>
CC: Vincent Abriou <vincent.abriou@st.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180321102029.15248-5-peter.ujfalusi@ti.com

drm/tegra: Let core take care of normalizing the zpos

Set the drm_mode_config->normalize_zpos and call the generic
drm_atomic_helper_check() instead of duplicating it within
tegra_atomic_check().

Call tegra_display_hub_atomic_check() after the drm_atomic_helpre_check()
returned without error.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180321102029.15248-4-peter.ujfalusi@ti.com

drm/exynos: Let core take care of normalizing the zpos

Instead of re-implementing the drm_atomic_helper_check() locally with just
adding drm_atomic_normalize_zpos() into it, set the
drm_mode_config->normalize_zpos.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Inki Dae <inki.dae@samsung.com>
CC: Joonyoung Shim <jy0922.shim@samsung.com>
CC: Seung-Woo Kim <sw0312.kim@samsung.com>
CC: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180321102029.15248-3-peter.ujfalusi@ti.com

drm: Add drm_mode_config->normalize_zpos boolean

Instead of drivers duplicating the drm_atomic_helper_check() code to be
able to normalize the zpos they can use the normalize_zpos flag to let the
drm core to do it.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180321102029.15248-2-peter.ujfalusi@ti.com

drm: make drm_core_check_feature() bool that it is

Bool is the more appropriate return type here, use it.

Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180327204722.31246-3-jani.nikula@intel.com

drm: remove old documentation comment cruft from drmP.h

Throw out the leftovers.

Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180327204722.31246-2-jani.nikula@intel.com

drm: prefer inline over __inline__

Remove last users of __inline__.

Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180327204722.31246-1-jani.nikula@intel.com

drm/dp/mst: Fix off-by-one typo when dump payload table

It seems there is a classical off-by-one typo from the beginning
when commit

  ad7f8a1f9ced ("drm/helper: add Displayport multi-stream helper (v0.6)")

introduced a new helper.

Fix a typo by introducing a macro constant.

Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180319141932.37290-1-andriy.shevchenko@linux.intel.com

Merge tag 'drm-amdkfd-next-2018-03-27' of git://people.freedesktop.org/~gabbayo/linux into drm-next

- GPUVM support for dGPUs
- KFD events support for dGPUs
- Fix live-lock situation when restoring multiple evicted processes
- Fix VM page table allocation on large-bar systems
- Fix for build failure on frv architecture

* tag 'drm-amdkfd-next-2018-03-27' of git://people.freedesktop.org/~gabbayo/linux:
  drm/amdkfd: Use ordered workqueue to restore processes
  drm/amdgpu: Fix acquiring VM on large-BAR systems
  drm/amdkfd: Add module option for testing large-BAR functionality
  drm/amdkfd: Kmap event page for dGPUs
  drm/amdkfd: Add ioctls for GPUVM memory management
  drm/amdkfd: Add TC flush on VMID deallocation for Hawaii
  drm/amdkfd: Allocate CWSR trap handler memory for dGPUs
  drm/amdkfd: Add per-process IDR for buffer handles
  drm/amdkfd: Aperture setup for dGPUs
  drm/amdkfd: Remove limit on number of GPUs
  drm/amdkfd: Populate DRM render device minor
  drm/amdkfd: Create KFD VMs on demand
  drm/amdgpu: Add kfd2kgd interface to acquire an existing VM
  drm/amdgpu: Add helper to turn an existing VM into a compute VM
  drm/amdgpu: Fix initial validation of PD BO for KFD VMs
  drm/amdgpu: Move KFD-specific fields into struct amdgpu_vm
  drm/amdkfd: fix uninitialized variable use
  drm/amdkfd: add missing include of mm.h

Merge tag 'drm-intel-next-fixes-2018-03-27' of git://anongit.freedesktop.org/drm/drm-intel into drm-next

- Display fixes for booting with MST hub lid closed and display
  freezing after hibernation (fd.o bugs 105470 & 105196)
- Fix for a very rare interrupt handling race resulting in GPU hang

* tag 'drm-intel-next-fixes-2018-03-27' of git://anongit.freedesktop.org/drm/drm-intel:
  drm/i915: Fix hibernation with ACPI S0 target state
  drm/i915/execlists: Use a locked clear_bit() for synchronisation with interrupt
  drm/i915: Specify which engines to reset following semaphore/event lockups
  drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.

Backmerge tag 'v4.16-rc7' into drm-next

Linux 4.16-rc7

This was requested by Daniel, and things were getting
a bit hard to reconcile, most of the conflicts were
trivial though.

drm/i915: Fix hibernation with ACPI S0 target state

After

commit dd9f31c7a3887950cbd0d49eb9d43f7a1518a356
Author: Imre Deak <imre.deak@intel.com>
Date:   Wed Aug 16 17:46:07 2017 +0300

    drm/i915/gen9+: Set same power state before hibernation image
    save/restore

during hibernation/suspend the power domain functionality got disabled,
after which resume could leave it incorrectly disabled if the ACPI
target state was S0 during suspend and i915 was not loaded by the loader
kernel.

This was caused by not considering if we resumed from hibernation as the
condition for power domains reiniting.

Fix this by simply tracking if we suspended power domains during system
suspend and reinit power domains accordingly during resume. This will
result in reiniting power domains always when resuming from hibernation,
regardless of the platform and whether or not i915 is loaded by the
loader kernel.

The reason we didn't catch this earlier is that the enabled/disabled
state of power domains during PMSG_FREEZE/PMSG_QUIESCE is platform
and kernel config dependent: on my SKL the target state is S4
during PMSG_FREEZE and (with the driver loaded in the loader kernel)
S0 during PMSG_QUIESCE. On the reporter's machine it's S0 during
PMSG_FREEZE but (contrary to this) power domains are not initialized
during PMSG_QUIESCE since i915 is not loaded in the loader kernel, or
it's loaded but without the DMC firmware being available.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105196
Reported-and-tested-by: amn-bas@hotmail.com
Fixes: dd9f31c7a388 ("drm/i915/gen9+: Set same power state before hibernation image save/restore")
Cc: amn-bas@hotmail.com
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322143642.26883-1-imre.deak@intel.com
(cherry picked from commit 0f90603c33bdf6575cfdc81edd53f3f13ba166fb)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915/execlists: Use a locked clear_bit() for synchronisation with interrupt

We were relying on the uncached reads when processing the CSB to provide
ourselves with the serialisation with the interrupt handler (so we could
detect new interrupts in the middle of processing the old one). However,
in commit 767a983ab255 ("drm/i915/execlists: Read the context-status HEAD
from the HWSP") those uncached reads were eliminated (on one path at
least) and along with them our serialisation. The result is that we
would very rarely miss notification of a new interrupt and leave a
context-switch unprocessed, hanging the GPU.

Fixes: 767a983ab255 ("drm/i915/execlists: Read the context-status HEAD from the HWSP")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180321091027.21034-1-chris@chris-wilson.co.uk
(cherry picked from commit 9153e6b7c85edbc89e874e5c83f86217c53dcfaf)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915: Specify which engines to reset following semaphore/event lockups

If the GPU is stuck waiting for an event or for a semaphore, we need to
reset the GPU in order to recover. We have to tell the reset routine
which engines we want reset, but we were still using the old interface
and declaring it as "not-fatal".

Fixes: 14b730fcb8d9 ("drm/i915/tdr: Prepare error handler to accept mask of hung engines")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180320100449.1360-1-chris@chris-wilson.co.uk
(cherry picked from commit ca98317b89428e6ac17be0938b467ed78654dd56)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.

If bios sets up an MST output and hardware state readout code sees this is
an SST configuration, when disabling the encoder we end up calling
->post_disable_dp() hook instead of the MST version. Consequently, we write
to the DP_SET_POWER dpcd to set it D3 state. Further along when we try
enable the encoder in MST mode, POWER_UP_PHY transaction fails to power up
the MST hub. This results in continuous link training failures which keep
the system busy delaying boot. We could identify bios MST boot discrepancy
and handle it accordingly but a simple way to solve this is to write to the
DP_SET_POWER dpcd for MST too.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105470
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reported-by: Laura Abbott <labbott@redhat.com>
Cc: stable@vger.kernel.org
Fixes: 5ea2355a100a ("drm/i915/mst: Use MST sideband message transactions for dpms control")
Tested-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180314054825.1718-1-dhinakaran.pandiyan@intel.com
(cherry picked from commit ad260ab32a4d94fa974f58262f8000472d34fd5b)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

drm/tinydrm: Use gem_free_object_unlocked

tinydrm doesn't use dev->struct_mutex and therefore has no need to use
gem_free_object.

Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: "Noralf Trønnes" <noralf@tronnes.org>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322105133.11211-2-daniel.vetter@ffwll.ch

drm/scdc-helper: Convert errors into debug messages

Since we may attempt to reconfigure SCDC when the sink has already been
disconnected we probably shouldn't scare the user with errors in dmesg
that are 100% expected in that case. Just leave it up to the caller
whether to print an error message or not, and just output debug
messages from the helper itself.

Cc: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180323182537.30784-1-ville.syrjala@linux.intel.com
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>

drm/gem: Document that handle_create must be the last step

It published the gem object to userspace, by that point other threads
can guess the id and start using it. And gem IDs are _very_ easy to
guess (it's just an idr).

Since gem objects is the only thing we allow drivers to create
themselves (all the kms/prime/syncobj stuff is handled by the core) no
other functions seem to be in need of this clarification.

Motivated by reviewing the xen-front kms driver.

Cc: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Reviewed-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180322080233.17266-1-daniel.vetter@ffwll.ch

gpu: drm: nouveau: Use list_{next/prev}_entry instead of list_entry

It's better to use list_entry instead of list_{next/prev}_entry
as it makes the code more clear to read.
This patch replace list_entry with list_{next/prev}_entry.

Signed-off-by: Arushi Singhal <arushisinghal19971997@gmail.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1522000893-5331-3-git-send-email-arushisinghal19971997@gmail.com

gpu: drm/lease:: Use list_{next/prev}_entry instead of list_entry

It's better to use list_entry instead of list_{next/prev}_entry
as it makes the code more clear to read.
This patch replace list_entry with list_{next/prev}_entry.

Signed-off-by: Arushi Singhal <arushisinghal19971997@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1522000893-5331-2-git-send-email-arushisinghal19971997@gmail.com

Merge branch 'drm-next-4.17' of git://people.freedesktop.org/~agd5f/linux into drm-next

Last pull for 4.17.  Highlights:
- Vega12 support
- A few more bug fixes and cleanups for powerplay

* 'drm-next-4.17' of git://people.freedesktop.org/~agd5f/linux: (77 commits)
  drm/amd/pp: clean header file hwmgr.h
  drm/amd/pp: use mlck_table.count for array loop index limit
  drm/amdgpu: Add an ATPX quirk for hybrid laptop
  drm/amdgpu: fix spelling mistake: "asssert" -> "assert"
  drm/amd/pp: Add new asic support in pp_psm.c
  drm/amd/pp: Clean up powerplay code on Vega12
  drm/amd/pp: Add smu irq handlers for legacy asics
  drm/amd/pp: Fix set wrong temperature range on smu7
  drm/amdgpu: Don't change preferred domian when fallback GTT v5
  drm/amdgpu: Fix NULL ptr on driver unload due to init failure.
  drm/amdgpu: fix "mitigate workaround for i915"
  drm/amd/pp: Add smu irq handlers in sw_init instand of hw_init
  drm/amd/pp: Refine register_thermal_interrupt function
  drm/amdgpu: Remove wrapper layer of cgs irq handling
  drm/amd/powerplay: Return per DPM level clock
  drm/amd/powerplay: Remove the SOC floor voltage setting
  drm/amdgpu: no job timeout setting on compute queues
  drm/amdgpu: add vega12 pci ids (v2)
  drm/amd/powerplay: add the hw manager for vega12 (v4)
  drm/amd/powerplay: add the smu manager for vega12 (v4)
  ...

Linux 4.16-rc7

Merge tag 'dmaengine-fix-4.16-rc7' of git://git./linux/kernel/git/vkoul/slave-dma

Pull dmaengine fix from Vinod Koul:
 "One small fix for stm32-dmamux fixing buffer overflow"

* tag 'dmaengine-fix-4.16-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/slave-dma:
  dmaengine: stm32-dmamux: fix a potential buffer overflow

Merge branch 'x86-pti-for-linus' of git://git./linux/kernel/git/tip/tip

Pull x86 and PTI fixes from Ingo Molnar:
 "Misc fixes:

   - fix EFI pagetables freeing

   - fix vsyscall pagetable setting on Xen PV guests

   - remove ancient CONFIG_X86_PPRO_FENCE=y - x86 is TSO again

   - fix two binutils (ld) development version related incompatibilities

   - clean up breakpoint handling

   - fix an x86 self-test"

* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/entry/64: Don't use IST entry for #BP stack
  x86/efi: Free efi_pgd with free_pages()
  x86/vsyscall/64: Use proper accessor to update P4D entry
  x86/cpu: Remove the CONFIG_X86_PPRO_FENCE=y quirk
  x86/boot/64: Verify alignment of the LOAD segment
  x86/build/64: Force the linker to use 2MB page size
  selftests/x86/ptrace_syscall: Fix for yet more glibc interference

Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull timer fix from Ingo Molnar:
 "Make posix clock ID usage Spectre-safe"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  posix-timers: Protect posix clock array access against speculation

Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull scheduler fixes from Ingo Molnar:
 "Two sched debug output related fixes: a console output fix and
  formatting fixes"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/debug: Adjust newlines for better alignment
  sched/debug: Fix per-task line continuation for console output

Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull perf fixes from Ingo Molnar:
 "Misc kernel side fixes.

  Generic:
   - cgroup events counting fix

  x86:
   - Intel PMU truncated-parameter fix

   - RDPMC fix

   - API naming fix/rename

   - uncore driver big-hardware PCI enumeration fix

   - uncore driver filter constraint fix"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/cgroup: Fix child event counting bug
  perf/x86/intel/uncore: Fix multi-domain PCI CHA enumeration bug on Skylake servers
  perf/x86/intel: Rename confusing 'freerunning PEBS' API and implementation to 'large PEBS'
  perf/x86/intel/uncore: Add missing filter constraint for SKX CHA event
  perf/x86/intel: Don't accidentally clear high bits in bdw_limit_period()
  perf/x86/intel: Disable userspace RDPMC usage for large PEBS

Merge branch 'locking-urgent-for-linus' of git://git./linux/kernel/git/tip/tip

Pull locking fixes from Ingo Molnar:
 "Two fixes: tighten up a jump-labels warning to not trigger on certain
  modules and fix confusing (and non-existent) mutex API documentation"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  jump_label: Disable jump labels in __exit code
  locking/mutex: Improve documentation

tty: vt: fix up tabstops properly

Tabs on a console with long lines do not wrap properly, so correctly
account for the line length when computing the tab placement location.

Reported-by: James Holderness <j4_james@hotmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'for-linus' of git://git./linux/kernel/git/ebiederm/user-namespace

Pull mqueuefs revert from Eric Biederman:
 "This fixes a regression that came in the merge window for v4.16.

  The problem is that the permissions for mounting and using the
  mqueuefs filesystem are broken. The necessary permission check is
  missing letting people who should not be able to mount mqueuefs mount
  mqueuefs. The field sb->s_user_ns is set incorrectly not allowing the
  mounter of mqueuefs to remount and otherwise have proper control over
  the filesystem.

  Al Viro and I see the path to the necessary fixes differently and I am
  not even certain at this point he actually sees all of the necessary
  fixes. Given a couple weeks we can probably work something out but I
  don't see the review being resolved in time for the final v4.16. I
  don't want v4.16 shipping with a nasty regression. So unfortunately I
  am sending a revert"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
  Revert "mqueue: switch to on-demand creation of internal mount"

Revert "mqueue: switch to on-demand creation of internal mount"

This reverts commit 36735a6a2b5e042db1af956ce4bcc13f3ff99e21.

Aleksa Sarai <asarai@suse.de> writes:
> [REGRESSION v4.16-rc6] [PATCH] mqueue: forbid unprivileged user access to internal mount
>
> Felix reported weird behaviour on 4.16.0-rc6 with regards to mqueue[1],
> which was introduced by 36735a6a2b5e ("mqueue: switch to on-demand
> creation of internal mount").
>
> Basically, the reproducer boils down to being able to mount mqueue if
> you create a new user namespace, even if you don't unshare the IPC
> namespace.
>
> Previously this was not possible, and you would get an -EPERM. The mount
> is the *host* mqueue mount, which is being cached and just returned from
> mqueue_mount(). To be honest, I'm not sure if this is safe or not (or if
> it was intentional -- since I'm not familiar with mqueue).
>
> To me it looks like there is a missing permission check. I've included a
> patch below that I've compile-tested, and should block the above case.
> Can someone please tell me if I'm missing something? Is this actually
> safe?
>
> [1]: https://github.com/docker/docker/issues/36674

The issue is a lot deeper than a missing permission check.  sb->s_user_ns
was is improperly set as well.  So in addition to the filesystem being
mounted when it should not be mounted, so things are not allow that should
be.

We are practically to the release of 4.16 and there is no agreement between
Al Viro and myself on what the code should looks like to fix things properly.
So revert the code to what it was before so that we can take our time
and discuss this properly.

Fixes: 36735a6a2b5e ("mqueue: switch to on-demand creation of internal mount")
Reported-by: Felix Abecassis <fabecassis@nvidia.com>
Reported-by: Aleksa Sarai <asarai@suse.de>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>

Merge tag 'pinctrl-v4.16-3' of git://git./linux/kernel/git/linusw/linux-pinctrl

Pull pin control fixes from Linus Walleij:
 "Two fixes for pin control for v4.16:

   - Renesas SH-PFC: remove a duplicate clkout pin which was causing
     crashes

   - fix Samsung out of bounds exceptions"

* tag 'pinctrl-v4.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: samsung: Validate alias coming from DT
  pinctrl: sh-pfc: r8a7795: remove duplicate of CLKOUT pin in pinmux_pins[]

Merge tag 'trace-v4.16-rc4' of git://git./linux/kernel/git/rostedt/linux-trace

Pull kprobe fixes from Steven Rostedt:
 "The documentation for kprobe events says that symbol offets can take
  both a + and - sign to get to befor and after the symbol address.

  But in actuality, the code does not support the minus. This fixes that
  issue, and adds a few more selftests to kprobe events"

* tag 'trace-v4.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  selftests: ftrace: Add a testcase for probepoint
  selftests: ftrace: Add a testcase for string type with kprobe_event
  selftests: ftrace: Add probe event argument syntax testcase
  tracing: probeevent: Fix to support minus offset from symbol

x86/entry/64: Don't use IST entry for #BP stack

There's nothing IST-worthy about #BP/int3.  We don't allow kprobes
in the small handful of places in the kernel that run at CPL0 with
an invalid stack, and 32-bit kernels have used normal interrupt
gates for #BP forever.

Furthermore, we don't allow kprobes in places that have usergs while
in kernel mode, so "paranoid" is also unnecessary.

Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org

drm/amdkfd: Use ordered workqueue to restore processes

Restoring multiple processes concurrently can lead to live-locks
where each process prevents the other from validating all its BOs.

v2: fix duplicate check of same variable

Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>

drm/amdgpu: Fix acquiring VM on large-BAR systems

On large-BAR systems the VM page tables for compute are accessed by
the CPU. Always allow CPU access to the page directory so that it can
be used later by the CPU when a VM is converted to a compute VM.

Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>

x86/efi: Free efi_pgd with free_pages()

The efi_pgd is allocated as PGD_ALLOCATION_ORDER pages and therefore must
also be freed as PGD_ALLOCATION_ORDER pages with free_pages().

Fixes: d9e9a6418065 ("x86/mm/pti: Allocate a separate user PGD")
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1521746333-19593-1-git-send-email-longman@redhat.com

Merge tag 'mips_fixes_4.16_5' of git://git./linux/kernel/git/jhogan/mips

Pull MIPS fixes from James Hogan:
 "Another miscellaneous pile of MIPS fixes for 4.16:

   - lantiq: fixes for clocks and Amazon SE (4.14)

   - ralink: fix booting on MT7621 (4.5)

   - ralink: fix halt (3.9)"

* tag 'mips_fixes_4.16_5' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips:
  MIPS: ralink: Fix booting on MT7621
  MIPS: ralink: Remove ralink_halt()
  MIPS: lantiq: ase: Enable MFD_SYSCON
  MIPS: lantiq: Enable AHB Bus for USB
  MIPS: lantiq: Fix Danube USB clock

Merge tag 'vfio-v4.16-rc7' of git://github.com/awilliam/linux-vfio

Pull VFIO fix from Alex Williamson:
 "Revert masking INTx where it cannot be enabled - it plays poorly with
  SR-IOV VFs and presumes DisINTx support"

* tag 'vfio-v4.16-rc7' of git://github.com/awilliam/linux-vfio:
  Revert: "vfio-pci: Mask INTx if a device is not capabable of enabling it"

Merge tag 'mtd/fixes-for-4.16-rc7' of git://git.infradead.org/linux-mtd

Pull MTD fixes from Boris Brezillon:

 - Fix several problems in the fsl_ifc NAND controller driver

 - Fix misuse of mtd_ooblayout_ecc() in mtdchar.c

* tag 'mtd/fixes-for-4.16-rc7' of git://git.infradead.org/linux-mtd:
  mtd: nand: fsl_ifc: Read ECCSTAT0 and ECCSTAT1 registers for IFC 2.0
  mtd: nand: fsl_ifc: Fix eccstat array overflow for IFC ver >= 2.0.0
  mtd: nand: fsl_ifc: Fix nand waitfunc return value
  mtdchar: fix usage of mtd_ooblayout_ecc()

Merge tag 'staging-4.16-rc7' of git://git./linux/kernel/git/gregkh/staging

Pull staging/IIO fixes from Greg KH:
 "Here are a few small staging and IIO fixes for various reported
  issues.

  All of them are tiny, the majority being iio driver fixes for small
  issues, and one staging driver fix for a memory corruption issue.

  All have been in linux-next with no reported issues"

* tag 'staging-4.16-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: ncpfs: memory corruption in ncp_read_kernel()
  iio: st_pressure: st_accel: pass correct platform data to init
  Revert "iio: accel: st_accel: remove redundant pointer pdata"
  iio: adc: meson-saradc: unlock on error in meson_sar_adc_lock()
  dt-bindings: iio: adc: sd-modulator: fix io-channel-cells
  iio: adc: stm32-dfsdm: fix multiple channel initialization
  iio: adc: stm32-dfsdm: fix clock source selection
  iio: adc: stm32-dfsdm: fix call to stop channel
  iio: adc: stm32-dfsdm: fix compatible data use
  iio: chemical: ccs811: Corrected firmware boot/application mode transition