Lukas Wunner [Wed, 20 Mar 2019 14:02:00 +0000 (15:02 +0100)]
net: ks8851: Set initial carrier state to down
The ks8851 chip's initial carrier state is down. A Link Change Interrupt
is signaled once interrupts are enabled if the carrier is up.
The ks8851 driver has it backwards by assuming that the initial carrier
state is up. The state is therefore misrepresented if the interface is
opened with no cable attached. Fix it.
The Link Change interrupt is sometimes not signaled unless the P1MBSR
register (which contains the Link Status bit) is read on ->ndo_open().
This might be a hardware erratum. Read the register by calling
mii_check_link(), which has the desirable side effect of setting the
carrier state to down if the cable was detached while the interface was
closed.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lukas Wunner [Wed, 20 Mar 2019 14:02:00 +0000 (15:02 +0100)]
net: ks8851: Delay requesting IRQ until opened
The ks8851 driver currently requests the IRQ before registering the
net_device. Because the net_device name is used as IRQ name and is
still "eth%d" when the IRQ is requested, it's impossibe to tell IRQs
apart if multiple ks8851 chips are present. Most other drivers delay
requesting the IRQ until the net_device is opened. Do the same.
The driver doesn't enable interrupts on the chip before opening the
net_device and disables them when closing it, so there doesn't seem to
be a need to request the IRQ already on probe.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lukas Wunner [Wed, 20 Mar 2019 14:02:00 +0000 (15:02 +0100)]
net: ks8851: Reassert reset pin if chip ID check fails
Commit
73fdeb82e963 ("net: ks8851: Add optional vdd_io regulator and
reset gpio") amended the ks8851 driver to briefly assert the chip's
reset pin on probe. It also amended the probe routine's error path to
reassert the reset pin if a subsequent initialization step fails.
However the commit misplaced reassertion of the reset pin in the error
path such that it is not performed if the check of the Chip ID and
Enable Register (CIDER) fails. The error path is therefore slightly
asymmetrical to the probe routine's body. Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lukas Wunner [Wed, 20 Mar 2019 14:02:00 +0000 (15:02 +0100)]
net: ks8851: Dequeue RX packets explicitly
The ks8851 driver lets the chip auto-dequeue received packets once they
have been read in full. It achieves that by setting the ADRFE flag in
the RXQCR register ("Auto-Dequeue RXQ Frame Enable").
However if allocation of a packet's socket buffer or retrieval of the
packet over the SPI bus fails, the packet will not have been read in
full and is not auto-dequeued. Such partial retrieval of a packet
confuses the chip's RX queue management: On the next RX interrupt,
the first packet read from the queue will be the one left there
previously and this one can be retrieved without issues. But for any
newly received packets, the frame header status and byte count registers
(RXFHSR and RXFHBCR) contain bogus values, preventing their retrieval.
The chip allows explicitly dequeueing a packet from the RX queue by
setting the RRXEF flag in the RXQCR register ("Release RX Error Frame").
This could be used to dequeue the packet in case of an error, but if
that error is a failed SPI transfer, it is unknown if the packet was
transferred in full and was auto-dequeued or if it was only transferred
in part and requires an explicit dequeue. The safest approach is thus
to always dequeue packets explicitly and forgo auto-dequeueing.
Without this change, I've witnessed packet retrieval break completely
when an SPI DMA transfer fails, requiring a chip reset. Explicit
dequeueing magically fixes this and makes packet retrieval absolutely
robust for me.
The chip's documentation suggests auto-dequeuing and uses the RRXEF
flag only to dequeue error frames which the driver doesn't want to
retrieve. But that seems to be a fair-weather approach.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Wed, 20 Mar 2019 06:49:38 +0000 (14:49 +0800)]
sctp: use memdup_user instead of vmemdup_user
In sctp_setsockopt_bindx()/__sctp_setsockopt_connectx(), it allocates
memory with addrs_size which is passed from userspace. We used flag
GFP_USER to put some more restrictions on it in Commit
cacc06215271
("sctp: use GFP_USER for user-controlled kmalloc").
However, since Commit
c981f254cc82 ("sctp: use vmemdup_user() rather
than badly open-coding memdup_user()"), vmemdup_user() has been used,
which doesn't check GFP_USER flag when goes to vmalloc_*(). So when
addrs_size is a huge value, it could exhaust memory and even trigger
oom killer.
This patch is to use memdup_user() instead, in which GFP_USER would
work to limit the memory allocation with a huge addrs_size.
Note we can't fix it by limiting 'addrs_size', as there's no demand
for it from RFC.
Reported-by: syzbot+ec1b7575afef85a0e5ca@syzkaller.appspotmail.com
Fixes: c981f254cc82 ("sctp: use vmemdup_user() rather than badly open-coding memdup_user()")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Wed, 20 Mar 2019 06:45:48 +0000 (14:45 +0800)]
ipv6: make ip6_create_rt_rcu return ip6_null_entry instead of NULL
Jianlin reported a crash:
[ 381.484332] BUG: unable to handle kernel NULL pointer dereference at
0000000000000068
[ 381.619802] RIP: 0010:fib6_rule_lookup+0xa3/0x160
[ 382.009615] Call Trace:
[ 382.020762] <IRQ>
[ 382.030174] ip6_route_redirect.isra.52+0xc9/0xf0
[ 382.050984] ip6_redirect+0xb6/0xf0
[ 382.066731] icmpv6_notify+0xca/0x190
[ 382.083185] ndisc_redirect_rcv+0x10f/0x160
[ 382.102569] ndisc_rcv+0xfb/0x100
[ 382.117725] icmpv6_rcv+0x3f2/0x520
[ 382.133637] ip6_input_finish+0xbf/0x460
[ 382.151634] ip6_input+0x3b/0xb0
[ 382.166097] ipv6_rcv+0x378/0x4e0
It was caused by the lookup function __ip6_route_redirect() returns NULL in
fib6_rule_lookup() when ip6_create_rt_rcu() returns NULL.
So we fix it by simply making ip6_create_rt_rcu() return ip6_null_entry
instead of NULL.
v1->v2:
- move down 'fallback:' to make it more readable.
Fixes: e873e4b9cc7e ("ipv6: use fib6_info_hold_safe() when necessary")
Reported-by: Jianlin Shi <jishi@redhat.com>
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Acked-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christoph Paasch [Tue, 19 Mar 2019 06:14:52 +0000 (23:14 -0700)]
net/packet: Set __GFP_NOWARN upon allocation in alloc_pg_vec
Since commit
fc62814d690c ("net/packet: fix 4gb buffer limit due to overflow check")
one can now allocate packet ring buffers >= UINT_MAX. However, syzkaller
found that that triggers a warning:
[ 21.100000] WARNING: CPU: 2 PID: 2075 at mm/page_alloc.c:4584 __alloc_pages_nod0
[ 21.101490] Modules linked in:
[ 21.101921] CPU: 2 PID: 2075 Comm: syz-executor.0 Not tainted 5.0.0 #146
[ 21.102784] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 0.5.1 01/01/2011
[ 21.103887] RIP: 0010:__alloc_pages_nodemask+0x2a0/0x630
[ 21.104640] Code: fe ff ff 65 48 8b 04 25 c0 de 01 00 48 05 90 0f 00 00 41 bd 01 00 00 00 48 89 44 24 48 e9 9c fe 3
[ 21.107121] RSP: 0018:
ffff88805e1cf920 EFLAGS:
00010246
[ 21.107819] RAX:
0000000000000000 RBX:
ffffffff85a488a0 RCX:
0000000000000000
[ 21.108753] RDX:
0000000000000000 RSI:
dffffc0000000000 RDI:
0000000000000000
[ 21.109699] RBP:
1ffff1100bc39f28 R08:
ffffed100bcefb67 R09:
ffffed100bcefb67
[ 21.110646] R10:
0000000000000001 R11:
ffffed100bcefb66 R12:
000000000000000d
[ 21.111623] R13:
0000000000000000 R14:
ffff88805e77d888 R15:
000000000000000d
[ 21.112552] FS:
00007f7c7de05700(0000) GS:
ffff88806d100000(0000) knlGS:
0000000000000000
[ 21.113612] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 21.114405] CR2:
000000000065c000 CR3:
000000005e58e006 CR4:
00000000001606e0
[ 21.115367] Call Trace:
[ 21.115705] ? __alloc_pages_slowpath+0x21c0/0x21c0
[ 21.116362] alloc_pages_current+0xac/0x1e0
[ 21.116923] kmalloc_order+0x18/0x70
[ 21.117393] kmalloc_order_trace+0x18/0x110
[ 21.117949] packet_set_ring+0x9d5/0x1770
[ 21.118524] ? packet_rcv_spkt+0x440/0x440
[ 21.119094] ? lock_downgrade+0x620/0x620
[ 21.119646] ? __might_fault+0x177/0x1b0
[ 21.120177] packet_setsockopt+0x981/0x2940
[ 21.120753] ? __fget+0x2fb/0x4b0
[ 21.121209] ? packet_release+0xab0/0xab0
[ 21.121740] ? sock_has_perm+0x1cd/0x260
[ 21.122297] ? selinux_secmark_relabel_packet+0xd0/0xd0
[ 21.123013] ? __fget+0x324/0x4b0
[ 21.123451] ? selinux_netlbl_socket_setsockopt+0x101/0x320
[ 21.124186] ? selinux_netlbl_sock_rcv_skb+0x3a0/0x3a0
[ 21.124908] ? __lock_acquire+0x529/0x3200
[ 21.125453] ? selinux_socket_setsockopt+0x5d/0x70
[ 21.126075] ? __sys_setsockopt+0x131/0x210
[ 21.126533] ? packet_release+0xab0/0xab0
[ 21.127004] __sys_setsockopt+0x131/0x210
[ 21.127449] ? kernel_accept+0x2f0/0x2f0
[ 21.127911] ? ret_from_fork+0x8/0x50
[ 21.128313] ? do_raw_spin_lock+0x11b/0x280
[ 21.128800] __x64_sys_setsockopt+0xba/0x150
[ 21.129271] ? lockdep_hardirqs_on+0x37f/0x560
[ 21.129769] do_syscall_64+0x9f/0x450
[ 21.130182] entry_SYSCALL_64_after_hwframe+0x49/0xbe
We should allocate with __GFP_NOWARN to handle this.
Cc: Kal Conley <kal.conley@dectris.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Fixes: fc62814d690c ("net/packet: fix 4gb buffer limit due to overflow check")
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vinay K Nallamothu [Tue, 19 Mar 2019 22:41:18 +0000 (22:41 +0000)]
mpls: Fix 6PE forwarding
This patch adds support for 6PE (RFC 4798) which uses IPv4-mapped IPv6
nexthop to connect IPv6 islands over IPv4 only MPLS network core.
Prior to this fix, to find the link-layer destination mac address, 6PE
enabled host/router was sending IPv6 ND requests for IPv4-mapped IPv6
nexthop address over the interface facing the IPv4 only core which
wouldn't success as the core is IPv6 free.
This fix changes that behavior on 6PE host to treat the nexthop as IPv4
address and send ARP requests whenever the next-hop address is an
IPv4-mapped IPv6 address.
Below topology illustrates the issue and how the patch addresses it.
abcd::1.1.1.1 (lo) abcd::2.2.2.2 (lo)
R0 (PE/host)------------------------R1--------------------------------R2 (PE/host)
<--- IPv4 MPLS core ---> <------ IPv4 MPLS core -------->
eth1 eth2 eth3 eth4
172.18.0.10 172.18.0.11 172.19.0.11 172.19.0.12
ffff::172.18.0.10 ffff::172.19.0.12
<------------------IPv6 MPLS tunnel ---------------------->
R0 and R2 act as 6PE routers of IPv6 islands. R1 is IPv4 only with MPLS tunnels
between R0,R1 and R1,R2.
docker exec r0 ip -f inet6 route add abcd::2.2.2.2/128 nexthop encap mpls 100 via ::ffff:172.18.0.11 dev eth1
docker exec r2 ip -f inet6 route add abcd::1.1.1.1/128 nexthop encap mpls 200 via ::ffff:172.19.0.11 dev eth4
docker exec r1 ip -f mpls route add 100 via inet 172.19.0.12 dev eth3
docker exec r1 ip -f mpls route add 200 via inet 172.18.0.10 dev eth2
With the change, when R0 sends an IPv6 packet over MPLS tunnel to abcd::2.2.2.2,
using ::ffff:172.18.0.11 as the nexthop, it does neighbor discovery for
172.18.18.0.11.
Signed-off-by: Vinay K Nallamothu <nvinay@juniper.net>
Tested-by: Avinash Lingala <ar977m@att.com>
Tested-by: Aravind Srinivas Srinivasa Prabhakar <aprabh@juniper.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Tue, 19 Mar 2019 21:15:58 +0000 (22:15 +0100)]
3c515: fix integer overflow warning
clang points out a harmless signed integer overflow:
drivers/net/ethernet/3com/3c515.c:1530:66: error: implicit conversion from 'int' to 'short' changes value from 32783 to -32753 [-Werror,-Wconstant-conversion]
new_mode = SetRxFilter | RxStation | RxMulticast | RxBroadcast | RxProm;
~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~
drivers/net/ethernet/3com/3c515.c:1532:52: error: implicit conversion from 'int' to 'short' changes value from 32775 to -32761 [-Werror,-Wconstant-conversion]
new_mode = SetRxFilter | RxStation | RxMulticast | RxBroadcast;
~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~
drivers/net/ethernet/3com/3c515.c:1534:38: error: implicit conversion from 'int' to 'short' changes value from 32773 to -32763 [-Werror,-Wconstant-conversion]
new_mode = SetRxFilter | RxStation | RxBroadcast;
~ ~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~
Make the variable unsigned to avoid the overflow.
Fixes: Linux-2.1.128pre1
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 19 Mar 2019 12:46:18 +0000 (05:46 -0700)]
dccp: do not use ipv6 header for ipv4 flow
When a dual stack dccp listener accepts an ipv4 flow,
it should not attempt to use an ipv6 header or
inet6_iif() helper.
Fixes: 3df80d9320bc ("[DCCP]: Introduce DCCPv6")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 19 Mar 2019 12:45:35 +0000 (05:45 -0700)]
tcp: do not use ipv6 header for ipv4 flow
When a dual stack tcp listener accepts an ipv4 flow,
it should not attempt to use an ipv6 header or tcp_v6_iif() helper.
Fixes: 1397ed35f22d ("ipv6: add flowinfo for tcp6 pkt_options for all cases")
Fixes: df3687ffc665 ("ipv6: add the IPV6_FL_F_REFLECT flag to IPV6_FL_A_GET")
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aditya Pakki [Tue, 19 Mar 2019 03:19:44 +0000 (22:19 -0500)]
nfc: Fix to check for kmemdup failure
In case of kmemdup failure while setting the service name the patch
returns -ENOMEM upstream for processing.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Tue, 19 Mar 2019 02:16:53 +0000 (10:16 +0800)]
net-sysfs: call dev_hold if kobject_init_and_add success
In netdev_queue_add_kobject and rx_queue_add_kobject,
if sysfs_create_group failed, kobject_put will call
netdev_queue_release to decrease dev refcont, however
dev_hold has not be called. So we will see this while
unregistering dev:
unregister_netdevice: waiting for bcsh0 to become free. Usage count = -1
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: d0d668371679 ("net: don't decrement kobj reference count on init failure")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aaro Koskinen [Mon, 18 Mar 2019 21:36:08 +0000 (23:36 +0200)]
net: stmmac: fix memory corruption with large MTUs
When using 16K DMA buffers and ring mode, the DES3 refill is not working
correctly as the function is using a bogus pointer for checking the
private data. As a result stale pointers will remain in the RX descriptor
ring, so DMA will now likely overwrite/corrupt some already freed memory.
As simple reproducer, just receive some UDP traffic:
# ifconfig eth0 down; ifconfig eth0 mtu 9000; ifconfig eth0 up
# iperf3 -c 192.168.253.40 -u -b 0 -R
If you didn't crash by now check the RX descriptors to find non-contiguous
RX buffers:
cat /sys/kernel/debug/stmmaceth/eth0/descriptors_status
[...]
1 [0x2be5020]: 0xa3220321 0x9ffc1ffc 0x72d70082 0x130e207e
^^^^^^^^^^^^^^^^^^^^^
2 [0x2be5040]: 0xa3220321 0x9ffc1ffc 0x72998082 0x1311a07e
^^^^^^^^^^^^^^^^^^^^^
A simple ping test will now report bad data:
# ping -s 8200 192.168.253.40
PING 192.168.253.40 (192.168.253.40) 8200(8228) bytes of data.
8208 bytes from 192.168.253.40: icmp_seq=1 ttl=64 time=1.00 ms
wrong data byte #8144 should be 0xd0 but was 0x88
Fix the wrong pointer. Also we must refill DES3 only if the DMA buffer
size is 16K.
Fixes: 54139cf3bb33 ("net: stmmac: adding multiple buffers for rx")
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Mon, 18 Mar 2019 16:35:11 +0000 (17:35 +0100)]
mlxsw: core: mlxsw: core: avoid -Wint-in-bool-context warning
A recently added function in mlxsw triggers a harmless compiler warning:
In file included from drivers/net/ethernet/mellanox/mlxsw/core.h:17,
from drivers/net/ethernet/mellanox/mlxsw/core_env.c:7:
drivers/net/ethernet/mellanox/mlxsw/core_env.c: In function 'mlxsw_env_module_temp_thresholds_get':
drivers/net/ethernet/mellanox/mlxsw/reg.h:8015:45: error: '*' in boolean context, suggest '&&' instead [-Werror=int-in-bool-context]
#define MLXSW_REG_MTMP_TEMP_TO_MC(val) (val * 125)
~~~~~^~~~~~
drivers/net/ethernet/mellanox/mlxsw/core_env.c:116:8: note: in expansion of macro 'MLXSW_REG_MTMP_TEMP_TO_MC'
if (!MLXSW_REG_MTMP_TEMP_TO_MC(module_temp)) {
^~~~~~~~~~~~~~~~~~~~~~~~~
The warning is normally disabled, but it would be nice to enable
it to find real bugs, and there are no other known instances at
the moment.
Replace the negation with a zero-comparison, which also matches
the comment above it.
Fixes: d93c19a1d95c ("mlxsw: core: Add API for QSFP module temperature thresholds reading")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 19 Mar 2019 19:45:39 +0000 (12:45 -0700)]
Merge tag 'wireless-drivers-for-davem-2019-03-19' of git://git./linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 5.1
First set of fixes for 5.1. Lots of fixes for mt76 this time.
iwlwifi
* fix warning with do_div()
mt7601u
* avoid using hardware which is supported by mt76
mt76
* more fixes for hweight8() usage
* fix hardware restart for mt76x2
* fix writing txwi on USB devices
* fix (and disable by default) ED/CCA support on 76x2
* fix powersave issues on 7603
* fix return value check for ioremap on 7603
* fix duplicate USB device IDs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 19 Mar 2019 18:01:24 +0000 (11:01 -0700)]
Merge branch 'ieee802154-for-davem-2019-03-19' of git://git./linux/kernel/git/sschmidt/wpan
Stefan Schmidt says:
====================
pull-request: ieee802154 for net 2019-03-19
An update from ieee802154 for your *net* tree.
Kangjie Lu fixed a potential NULL pointer deref in the
adf7242 driver and Li
RongQing make sure we propagate a netlink return code to the caller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Stanislaw Gruszka [Tue, 12 Mar 2019 12:32:07 +0000 (13:32 +0100)]
mt76x02: do not enable RTS/CTS by default
My commit
26a7b5473191 ("mt76x02: set protection according to ht
operation element") enabled by default RTS/CTS protection for OFDM
and CCK traffic, because MT_TX_RTS_CFG_THRESH is configured to non
0xffff by initvals and .set_rts_threshold callback is not called by
mac80211 on initialization, only on user request or during
ieee80211_reconfig() (suspend/resuem or restart_hw).
Enabling RTS/CTS cause some problems when sending probe request
frames by hcxdumptool penetration tool, but I expect it can cause
other issues on different scenarios.
Restore previous setting of RTS/CTS being disabled by default for
OFDM/CCK by changing MT_TX_RTS_CFG_THRESH initvals to 0xffff.
Fixes: 26a7b5473191 ("mt76x02: set protection according to ht operation element")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Lorenzo Bianconi [Mon, 11 Mar 2019 13:24:35 +0000 (14:24 +0100)]
mt76: fix schedule while atomic in mt76x02_reset_state
Fix following schedule while atomic in mt76x02_reset_state
since synchronize_rcu is run inside a RCU section
[44036.944222] mt76x2e 0000:06:00.0: MCU message 31 (seq 3) timed out
[44036.944281] BUG: sleeping function called from invalid context at kernel/rcu/tree_exp.h:818
[44036.944284] in_atomic(): 1, irqs_disabled(): 0, pid: 28066, name: kworker/u4:1
[44036.944287] INFO: lockdep is turned off.
[44036.944292] CPU: 1 PID: 28066 Comm: kworker/u4:1 Tainted: G W 5.0.0-rc7-wdn-t1+ #7
[44036.944294] Hardware name: Dell Inc. Studio XPS 1340/0K183D, BIOS A11 09/08/2009
[44036.944305] Workqueue: phy1 mt76x02_wdt_work [mt76x02_lib]
[44036.944308] Call Trace:
[44036.944317] dump_stack+0x67/0x90
[44036.944322] ___might_sleep.cold.88+0x9f/0xaf
[44036.944327] rcu_blocking_is_gp+0x13/0x50
[44036.944330] synchronize_rcu+0x17/0x80
[44036.944337] mt76_sta_state+0x138/0x1d0 [mt76]
[44036.944349] mt76x02_wdt_work+0x1c9/0x610 [mt76x02_lib]
[44036.944355] process_one_work+0x2a5/0x620
[44036.944361] worker_thread+0x35/0x3e0
[44036.944368] kthread+0x11c/0x140
[44036.944376] ret_from_fork+0x3a/0x50
[44036.944384] BUG: scheduling while atomic: kworker/u4:1/28066/0x00000002
[44036.944387] INFO: lockdep is turned off.
[44036.944389] Modules linked in: cmac ctr ccm af_packet snd_hda_codec_hdmi
Introduce __mt76_sta_remove in order to run sta_remove without holding dev->mutex.
Move __mt76_sta_remove outside of RCU section in mt76x02_reset_state
Fixes: e4ebb8b403d1 ("mt76: mt76x2: implement full device restart on watchdog reset")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Felix Fietkau [Mon, 11 Mar 2019 13:09:53 +0000 (14:09 +0100)]
mt76: mt7603: use the correct hweight8() function
__sw_hweight8() is only defined if CONFIG_GENERIC_HWEIGHT is enabled.
The function that works on all architectures is hweight8().
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Stanislaw Gruszka [Thu, 7 Mar 2019 12:22:21 +0000 (13:22 +0100)]
mt76x02u: check chip version on probe
Since some USB device IDs are duplicated between mt76x0u, mt7601u
and mt76x2u device, check chip version on probe and return error if
not match the driver.
Don't think this is serious issue, probe most likely will fail at
some other point for wrong device, but we do not have to configure
it if we know is not our device.
Reported-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Stanislaw Gruszka [Thu, 7 Mar 2019 12:22:07 +0000 (13:22 +0100)]
mt7601u: check chip version on probe
Since some USB device IDs are duplicated between mt7601u and mt76x0u
devices, check chip version on probe and return error if not match
0x7601.
Don't think this is serious issue, probe most likely will fail at
some other point for wrong device, but we do not have to configure
it if we know is not mt7601u device.
Reported-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Stefan Schmidt [Tue, 19 Mar 2019 15:25:37 +0000 (16:25 +0100)]
Merge remote-tracking branch 'net/master'
Florian Fainelli [Mon, 18 Mar 2019 18:07:33 +0000 (11:07 -0700)]
Documentation: networking: Update netdev-FAQ regarding patches
Provide an explanation of what is expected with respect to sending new
versions of specific patches within a patch series, as well as what
happens if an earlier patch series accidentally gets merged).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 19 Mar 2019 01:34:45 +0000 (18:34 -0700)]
Merge branch 's390-qeth-fixes'
Julian Wiedmann says:
====================
s390/qeth: fixes 2019-03-18
please apply the following three patches to -net. The first two are fixes
for minor race conditions in the probe code, while the third one gets
dropwatch working (again).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Mon, 18 Mar 2019 15:40:56 +0000 (16:40 +0100)]
s390/qeth: be drop monitor friendly
As part of the TX completion path, qeth_release_skbs() frees the completed
skbs with __skb_queue_purge(). This ends in kfree_skb(), reporting every
completed skb as dropped.
On the other hand when dropping an skb in .ndo_start_xmit, we end up
calling consume_skb()... where we should be using kfree_skb() so that
drop monitors get notified.
Switch the drop/consume logic around, and also don't accumulate dropped
packets in the tx_errors statistics.
Fixes: dc149e3764d8 ("s390/qeth: replace open-coded skb_queue_walk()")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Mon, 18 Mar 2019 15:40:55 +0000 (16:40 +0100)]
s390/qeth: fix race when initializing the IP address table
The ucast IP table is utilized by some of the L3-specific sysfs attributes
that qeth_l3_create_device_attributes() provides. So initialize the table
_before_ registering the attributes.
Fixes: ebccc7397e4a ("s390/qeth: add missing hash table initializations")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Mon, 18 Mar 2019 15:40:54 +0000 (16:40 +0100)]
s390/qeth: don't erase configuration while probing
The HW trap and VNICC configuration is exposed via sysfs, and may have
already been modified when qeth_l?_probe_device() attempts to initialize
them. So (1) initialize the VNICC values a little earlier, and (2) don't
bother about the HW trap mode, it was already initialized before.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjorn Helgaas [Mon, 18 Mar 2019 13:51:06 +0000 (08:51 -0500)]
mISDN: hfcpci: Test both vendor & device ID for Digium HFC4S
The device ID alone does not uniquely identify a device. Test both the
vendor and device ID to make sure we don't mistakenly think some other
vendor's 0xB410 device is a Digium HFC4S. Also, instead of the bare hex
ID, use the same constant (PCI_DEVICE_ID_DIGIUM_HFC4S) used in the device
ID table.
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 19 Mar 2019 01:31:09 +0000 (18:31 -0700)]
Merge branch 'sctp-fix-ignoring-asoc_id-for-tcp-style-sockets-on-some-setsockopts'
Xin Long says:
====================
sctp: fix ignoring asoc_id for tcp-style sockets on some setsockopts
This is a patchset to fix ignoring asoc_id for tcp-style sockets on
some setsockopts, introduced by SCTP_CURRENT_ASSOC of the patchset:
[net-next,00/24] sctp: support SCTP_FUTURE/CURRENT/ALL_ASSOC
(https://patchwork.ozlabs.org/cover/
1031706/)
As Marcelo suggested, we fix it on each setsockopt that is using
SCTP_CURRENT_ASSOC one by one by adding the check:
if (sctp_style(sk, TCP))
xxx.xxx_assoc_id = SCTP_FUTURE_ASSOC;
so that assoc_id will be completely ingored for tcp-style socket on
setsockopts, and works as SCTP_FUTURE_ASSOC.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Mon, 18 Mar 2019 12:06:11 +0000 (20:06 +0800)]
sctp: fix ignoring asoc_id for tcp-style sockets on SCTP_STREAM_SCHEDULER sockopt
A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_STREAM_SCHEDULER sockopt.
Fixes: 7efba10d6bd2 ("sctp: add SCTP_FUTURE_ASOC and SCTP_CURRENT_ASSOC for SCTP_STREAM_SCHEDULER sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Mon, 18 Mar 2019 12:06:10 +0000 (20:06 +0800)]
sctp: fix ignoring asoc_id for tcp-style sockets on SCTP_EVENT sockopt
A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_EVENT sockopt.
Fixes: d251f05e3ba2 ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_EVENT sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Mon, 18 Mar 2019 12:06:09 +0000 (20:06 +0800)]
sctp: fix ignoring asoc_id for tcp-style sockets on SCTP_ENABLE_STREAM_RESET sockopt
A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_ENABLE_STREAM_RESET sockopt.
Fixes: 99a62135e127 ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_ENABLE_STREAM_RESET sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Mon, 18 Mar 2019 12:06:08 +0000 (20:06 +0800)]
sctp: fix ignoring asoc_id for tcp-style sockets on SCTP_DEFAULT_PRINFO sockopt
A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_DEFAULT_PRINFO sockopt.
Fixes: 3a583059d187 ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_DEFAULT_PRINFO sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Mon, 18 Mar 2019 12:06:07 +0000 (20:06 +0800)]
sctp: fix ignoring asoc_id for tcp-style sockets on SCTP_AUTH_DEACTIVATE_KEY sockopt
A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_AUTH_DEACTIVATE_KEY sockopt.
Fixes: 2af66ff3edc7 ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_AUTH_DEACTIVATE_KEY sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Mon, 18 Mar 2019 12:06:06 +0000 (20:06 +0800)]
sctp: fix ignoring asoc_id for tcp-style sockets on SCTP_AUTH_DELETE_KEY sockopt
A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_AUTH_DELETE_KEY sockopt.
Fixes: 3adcc300603e ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_AUTH_DELETE_KEY sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Mon, 18 Mar 2019 12:06:05 +0000 (20:06 +0800)]
sctp: fix ignoring asoc_id for tcp-style sockets on SCTP_AUTH_ACTIVE_KEY sockopt
A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_AUTH_ACTIVE_KEY sockopt.
Fixes: bf9fb6ad4f29 ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_AUTH_ACTIVE_KEY sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Mon, 18 Mar 2019 12:06:04 +0000 (20:06 +0800)]
sctp: fix ignoring asoc_id for tcp-style sockets on SCTP_AUTH_KEY sockopt
A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_AUTH_KEY sockopt.
Fixes: 7fb3be13a236 ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_AUTH_KEY sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Mon, 18 Mar 2019 12:06:03 +0000 (20:06 +0800)]
sctp: fix ignoring asoc_id for tcp-style sockets on SCTP_MAX_BURST sockopt
A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_MAX_BURST sockopt.
Fixes: e0651a0dc877 ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_MAX_BURST sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Mon, 18 Mar 2019 12:06:02 +0000 (20:06 +0800)]
sctp: fix ignoring asoc_id for tcp-style sockets on SCTP_CONTEXT sockopt
A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_CONTEXT sockopt.
Fixes: 49b037acca8c ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_CONTEXT sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Mon, 18 Mar 2019 12:06:01 +0000 (20:06 +0800)]
sctp: fix ignoring asoc_id for tcp-style sockets on SCTP_DEFAULT_SNDINFO sockopt
A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_DEFAULT_SNDINFO sockopt.
Fixes: 92fc3bd928c9 ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_DEFAULT_SNDINFO sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Mon, 18 Mar 2019 12:06:00 +0000 (20:06 +0800)]
sctp: fix ignoring asoc_id for tcp-style sockets on SCTP_DELAYED_SACK sockopt
A similar fix as Patch "sctp: fix ignoring asoc_id for tcp-style sockets on
SCTP_DEFAULT_SEND_PARAM sockopt" on SCTP_DELAYED_SACK sockopt.
Fixes: 9c5829e1c49e ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_DELAYED_SACK sockopt")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcelo Ricardo Leitner [Mon, 18 Mar 2019 12:05:59 +0000 (20:05 +0800)]
sctp: fix ignoring asoc_id for tcp-style sockets on SCTP_DEFAULT_SEND_PARAM sockopt
Currently if the user pass an invalid asoc_id to SCTP_DEFAULT_SEND_PARAM
on a TCP-style socket, it will silently ignore the new parameters.
That's because after not finding an asoc, it is checking asoc_id against
the known values of CURRENT/FUTURE/ALL values and that fails to match.
IOW, if the user supplies an invalid asoc id or not, it should either
match the current asoc or the socket itself so that it will inherit
these later. Fixes it by forcing asoc_id to SCTP_FUTURE_ASSOC in case it
is a TCP-style socket without an asoc, so that the values get set on the
socket.
Fixes: 707e45b3dc5a ("sctp: use SCTP_FUTURE_ASSOC and add SCTP_CURRENT_ASSOC for SCTP_DEFAULT_SEND_PARAM sockopt")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Mon, 18 Mar 2019 11:58:29 +0000 (19:58 +0800)]
sctp: not copy sctp_sock pd_lobby in sctp_copy_descendant
Now sctp_copy_descendant() copies pd_lobby from old sctp scok to new
sctp sock. If sctp_sock_migrate() returns error, it will panic when
releasing new sock and trying to purge pd_lobby due to the incorrect
pointers in pd_lobby.
[ 120.485116] kasan: CONFIG_KASAN_INLINE enabled
[ 120.486270] kasan: GPF could be caused by NULL-ptr deref or user
[ 120.509901] Call Trace:
[ 120.510443] sctp_ulpevent_free+0x1e8/0x490 [sctp]
[ 120.511438] sctp_queue_purge_ulpevents+0x97/0xe0 [sctp]
[ 120.512535] sctp_close+0x13a/0x700 [sctp]
[ 120.517483] inet_release+0xdc/0x1c0
[ 120.518215] __sock_release+0x1d2/0x2a0
[ 120.519025] sctp_do_peeloff+0x30f/0x3c0 [sctp]
We fix it by not copying sctp_sock pd_lobby in sctp_copy_descendan(),
and skb_queue_head_init() can also be removed in sctp_sock_migrate().
Reported-by: syzbot+85e0b422ff140b03672a@syzkaller.appspotmail.com
Fixes: 89664c623617 ("sctp: sctp_sock_migrate() returns error if sctp_bind_addr_dup() fails")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Mon, 18 Mar 2019 11:47:00 +0000 (19:47 +0800)]
sctp: get sctphdr by offset in sctp_compute_cksum
sctp_hdr(skb) only works when skb->transport_header is set properly.
But in Netfilter, skb->transport_header for ipv6 is not guaranteed
to be right value for sctphdr. It would cause to fail to check the
checksum for sctp packets.
So fix it by using offset, which is always right in all places.
v1->v2:
- Fix the changelog.
Fixes: e6d8b64b34aa ("net: sctp: fix and consolidate SCTP checksumming code")
Reported-by: Li Shuang <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yoshiki Komachi [Mon, 18 Mar 2019 05:39:52 +0000 (14:39 +0900)]
af_packet: fix the tx skb protocol in raw sockets with ETH_P_ALL
I am using "protocol ip" filters in TC to manipulate TC flower
classifiers, which are only available with "protocol ip". However,
I faced an issue that packets sent via raw sockets with ETH_P_ALL
did not match the ip filters even if they did satisfy the condition
(e.g., DHCP offer from dhcpd).
I have determined that the behavior was caused by an unexpected
value stored in skb->protocol, namely, ETH_P_ALL instead of ETH_P_IP,
when packets were sent via raw sockets with ETH_P_ALL set.
IMHO, storing ETH_P_ALL in skb->protocol is not appropriate for
packets sent via raw sockets because ETH_P_ALL is not a real ether
type used on wire, but a virtual one.
This patch fixes the tx protocol selection in cases of transmission
via raw sockets created with ETH_P_ALL so that it asks the driver to
extract protocol from the Ethernet header.
Fixes: 75c65772c3 ("net/packet: Ask driver for protocol if not provided by user")
Signed-off-by: Yoshiki Komachi <komachi.yoshiki@lab.ntt.co.jp>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maxime Chevallier [Sat, 16 Mar 2019 13:41:30 +0000 (14:41 +0100)]
packets: Always register packet sk in the same order
When using fanouts with AF_PACKET, the demux functions such as
fanout_demux_cpu will return an index in the fanout socket array, which
corresponds to the selected socket.
The ordering of this array depends on the order the sockets were added
to a given fanout group, so for FANOUT_CPU this means sockets are bound
to cpus in the order they are configured, which is OK.
However, when stopping then restarting the interface these sockets are
bound to, the sockets are reassigned to the fanout group in the reverse
order, due to the fact that they were inserted at the head of the
interface's AF_PACKET socket list.
This means that traffic that was directed to the first socket in the
fanout group is now directed to the last one after an interface restart.
In the case of FANOUT_CPU, traffic from CPU0 will be directed to the
socket that used to receive traffic from the last CPU after an interface
restart.
This commit introduces a helper to add a socket at the tail of a list,
then uses it to register AF_PACKET sockets.
Note that this changes the order in which sockets are listed in /proc and
with sock_diag.
Fixes: dc99f600698d ("packet: Add fanout support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zhiqiang Liu [Sat, 16 Mar 2019 09:02:54 +0000 (17:02 +0800)]
vxlan: Don't call gro_cells_destroy() before device is unregistered
Commit
ad6c9986bcb62 ("vxlan: Fix GRO cells race condition between
receive and link delete") fixed a race condition for the typical case a vxlan
device is dismantled from the current netns. But if a netns is dismantled,
vxlan_destroy_tunnels() is called to schedule a unregister_netdevice_queue()
of all the vxlan tunnels that are related to this netns.
In vxlan_destroy_tunnels(), gro_cells_destroy() is called and finished before
unregister_netdevice_queue(). This means that the gro_cells_destroy() call is
done too soon, for the same reasons explained in above commit.
So we need to fully respect the RCU rules, and thus must remove the
gro_cells_destroy() call or risk use after-free.
Fixes: 58ce31cca1ff ("vxlan: GRO support at tunnel layer")
Signed-off-by: Suanming.Mou <mousuanming@huawei.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Bogdanov [Sat, 16 Mar 2019 08:28:18 +0000 (08:28 +0000)]
net: aquantia: fix rx checksum offload for UDP/TCP over IPv6
TCP/UDP checksum validity was propagated to skb
only if IP checksum is valid.
But for IPv6 there is no validity as there is no checksum in IPv6.
This patch propagates TCP/UDP checksum validity regardless of IP checksum.
Fixes: 018423e90bee ("net: ethernet: aquantia: Add ring support code")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Finn Thain [Sat, 16 Mar 2019 03:21:19 +0000 (14:21 +1100)]
mac8390: Fix mmio access size probe
The bug that Stan reported is as follows. After a restart, a 16-bit NIC
may be incorrectly identified as a 32-bit NIC and stop working.
mac8390 slot.E: Memory length resource not found, probing
mac8390 slot.E: Farallon EtherMac II-C (type farallon)
mac8390 slot.E: MAC 00:00:c5:30:c2:99, IRQ 61, 32 KB shared memory at 0xfeed0000, 32-bit access.
The bug never arises after a cold start and only intermittently after a
warm start. (I didn't investigate why the bug is intermittent.)
It turns out that memcpy_toio() is deprecated and memcmp_withio() also
has issues. Replacing these calls with mmio accessors fixes the problem.
Reported-and-tested-by: Stan Johnson <userm57@yahoo.com>
Fixes: 2964db0f5904 ("m68k: Mac DP8390 update")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matteo Croce [Sat, 16 Mar 2019 00:00:50 +0000 (01:00 +0100)]
gtp: change NET_UDP_TUNNEL dependency to select
Similarly to commit
a7603ac1fc8c ("geneve: change NET_UDP_TUNNEL
dependency to select"), GTP has a dependency on NET_UDP_TUNNEL which
makes impossible to compile it if no other protocol depending on
NET_UDP_TUNNEL is selected.
Fix this by changing the depends to a select, and drop NET_IP_TUNNEL from
the select list, as it already depends on NET_UDP_TUNNEL.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 15 Mar 2019 17:41:14 +0000 (10:41 -0700)]
net: rose: fix a possible stack overflow
rose_write_internal() uses a temp buffer of 100 bytes, but a manual
inspection showed that given arbitrary input, rose_create_facilities()
can fill up to 110 bytes.
Lets use a tailroom of 256 bytes for peace of mind, and remove
the bounce buffer : we can simply allocate a big enough skb
and adjust its length as needed.
syzbot report :
BUG: KASAN: stack-out-of-bounds in memcpy include/linux/string.h:352 [inline]
BUG: KASAN: stack-out-of-bounds in rose_create_facilities net/rose/rose_subr.c:521 [inline]
BUG: KASAN: stack-out-of-bounds in rose_write_internal+0x597/0x15d0 net/rose/rose_subr.c:116
Write of size 7 at addr
ffff88808b1ffbef by task syz-executor.0/24854
CPU: 0 PID: 24854 Comm: syz-executor.0 Not tainted 5.0.0+ #97
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
print_address_description.cold+0x7c/0x20d mm/kasan/report.c:187
kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317
check_memory_region_inline mm/kasan/generic.c:185 [inline]
check_memory_region+0x123/0x190 mm/kasan/generic.c:191
memcpy+0x38/0x50 mm/kasan/common.c:131
memcpy include/linux/string.h:352 [inline]
rose_create_facilities net/rose/rose_subr.c:521 [inline]
rose_write_internal+0x597/0x15d0 net/rose/rose_subr.c:116
rose_connect+0x7cb/0x1510 net/rose/af_rose.c:826
__sys_connect+0x266/0x330 net/socket.c:1685
__do_sys_connect net/socket.c:1696 [inline]
__se_sys_connect net/socket.c:1693 [inline]
__x64_sys_connect+0x73/0xb0 net/socket.c:1693
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x458079
Code: ad b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:
00007f47b8d9dc78 EFLAGS:
00000246 ORIG_RAX:
000000000000002a
RAX:
ffffffffffffffda RBX:
0000000000000003 RCX:
0000000000458079
RDX:
000000000000001c RSI:
0000000020000040 RDI:
0000000000000004
RBP:
000000000073bf00 R08:
0000000000000000 R09:
0000000000000000
R10:
0000000000000000 R11:
0000000000000246 R12:
00007f47b8d9e6d4
R13:
00000000004be4a4 R14:
00000000004ceca8 R15:
00000000ffffffff
The buggy address belongs to the page:
page:
ffffea00022c7fc0 count:0 mapcount:0 mapping:
0000000000000000 index:0x0
flags: 0x1fffc0000000000()
raw:
01fffc0000000000 0000000000000000 ffffffff022c0101 0000000000000000
raw:
0000000000000000 0000000000000000 00000000ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff88808b1ffa80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff88808b1ffb00: 00 00 00 00 00 00 00 00 f1 f1 f1 f1 00 00 00 03
>
ffff88808b1ffb80: f2 f2 00 00 00 00 00 00 00 00 00 00 00 00 04 f3
^
ffff88808b1ffc00: f3 f3 f3 f3 00 00 00 00 00 00 00 00 00 00 00 00
ffff88808b1ffc80: 00 00 00 00 00 00 00 f1 f1 f1 f1 f1 f1 01 f2 01
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser [Mon, 18 Mar 2019 11:08:58 +0000 (12:08 +0100)]
doc: fix link to MSG_ZEROCOPY patchset
Use https and link to the patch directly.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Erik Hugne [Sun, 17 Mar 2019 17:46:42 +0000 (18:46 +0100)]
tipc: allow service ranges to be connect()'ed on RDM/DGRAM
We move the check that prevents connecting service ranges to after
the RDM/DGRAM check, and move address sanity control to a separate
function that also validates the service range.
Fixes: 23998835be98 ("tipc: improve address sanity check in tipc_connect()")
Signed-off-by: Erik Hugne <erik.hugne@gmail.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Randy Dunlap [Mon, 18 Mar 2019 00:17:45 +0000 (17:17 -0700)]
networking: fix snmp_counter.rst Doc. Warnings
Fix documentation markup warnings in snmp_counter.rst:
Documentation/networking/snmp_counter.rst:416: WARNING: Title underline too short.
Documentation/networking/snmp_counter.rst:684: WARNING: Bullet list ends without a blank line; unexpected unindent.
Documentation/networking/snmp_counter.rst:693: WARNING: Title underline too short.
Documentation/networking/snmp_counter.rst:707: WARNING: Bullet list ends without a blank line; unexpected unindent.
Documentation/networking/snmp_counter.rst:712: WARNING: Bullet list ends without a blank line; unexpected unindent.
Documentation/networking/snmp_counter.rst:722: WARNING: Title underline too short.
Documentation/networking/snmp_counter.rst:733: WARNING: Bullet list ends without a blank line; unexpected unindent.
Documentation/networking/snmp_counter.rst:736: WARNING: Bullet list ends without a blank line; unexpected unindent.
Documentation/networking/snmp_counter.rst:739: WARNING: Bullet list ends without a blank line; unexpected unindent.
Fixes: 80cc49507ba48 ("net: Add part of TCP counts explanations in snmp_counters.rst")
Fixes: 8e2ea53a83dfb ("add snmp counters document")
Fixes: a6c7c7aac2de6 ("net: add document for several snmp counters")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: yupeng <yupeng0921@gmail.com>
Kangjie Lu [Sat, 16 Mar 2019 21:46:05 +0000 (16:46 -0500)]
net: tipc: fix a missing check for nla_nest_start
nla_nest_start may fail. The fix check its status and returns
-EMSGSIZE in case it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 16 Mar 2019 20:09:53 +0000 (13:09 -0700)]
tun: add a missing rcu_read_unlock() in error path
In my latest patch I missed one rcu_read_unlock(), in case
device is down.
Fixes: 4477138fa0ae ("tun: properly test for IFF_UP")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 16 Mar 2019 19:20:08 +0000 (12:20 -0700)]
Merge git://git./pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2019-03-16
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a umem memory leak on cleanup in AF_XDP, from Björn.
2) Fix BTF to properly resolve forward-declared enums into their corresponding
full enum definition types during deduplication, from Andrii.
3) Fix libbpf to reject invalid flags in xsk_socket__create(), from Magnus.
4) Fix accessing invalid pointer returned from bpf_tcp_sock() and
bpf_sk_fullsock() after bpf_sk_release() was called, from Martin.
5) Fix generation of load/store DW instructions in PPC JIT, from Naveen.
6) Various fixes in BPF helper function documentation in bpf.h UAPI header
used to bpf-helpers(7) man page, from Quentin.
7) Fix segfault in BPF test_progs when prog loading failed, from Yonghong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kangjie Lu [Fri, 15 Mar 2019 17:11:59 +0000 (12:11 -0500)]
net: tipc: fix a missing check of nla_nest_start
nla_nest_start could fail and requires a check. The fix returns
-EMSGSIZE if it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kangjie Lu [Fri, 15 Mar 2019 06:14:33 +0000 (01:14 -0500)]
net: ncsi: fix a missing check for nla_nest_start
nla_nest_start may fail and thus deserves a check.
The fix returns -EMSGSIZE in case it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kangjie Lu [Fri, 15 Mar 2019 06:11:22 +0000 (01:11 -0500)]
net: openvswitch: fix missing checks for nla_nest_start
nla_nest_start may fail and thus deserves a check.
The fix returns -EMSGSIZE when it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kangjie Lu [Fri, 15 Mar 2019 04:20:16 +0000 (23:20 -0500)]
net: openvswitch: fix a NULL pointer dereference
upcall is dereferenced even when genlmsg_put fails. The fix
goto out to avoid the NULL pointer dereference in this case.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Naveen N. Rao [Fri, 15 Mar 2019 14:51:19 +0000 (20:21 +0530)]
powerpc: bpf: Fix generation of load/store DW instructions
Yauheni Kaliuta pointed out that PTR_TO_STACK store/load verifier test
was failing on powerpc64 BE, and rightfully indicated that the PPC_LD()
macro is not masking away the last two bits of the offset per the ISA,
resulting in the generation of 'lwa' instruction instead of the intended
'ld' instruction.
Segher also pointed out that we can't simply mask away the last two bits
as that will result in loading/storing from/to a memory location that
was not intended.
This patch addresses this by using ldx/stdx if the offset is not
word-aligned. We load the offset into a temporary register (TMP_REG_2)
and use that as the index register in a subsequent ldx/stdx. We fix
PPC_LD() macro to mask off the last two bits, but enhance PPC_BPF_LL()
and PPC_BPF_STL() to factor in the offset value and generate the proper
instruction sequence. We also convert all existing users of PPC_LD() and
PPC_STD() to use these macros. All existing uses of these macros have
been audited to ensure that TMP_REG_2 can be clobbered.
Fixes: 156d0e290e96 ("powerpc/ebpf/jit: Implement JIT compiler for extended BPF")
Cc: stable@vger.kernel.org # v4.9+
Reported-by: Yauheni Kaliuta <yauheni.kaliuta@redhat.com>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Björn Töpel [Wed, 13 Mar 2019 14:15:49 +0000 (15:15 +0100)]
xsk: fix umem memory leak on cleanup
When the umem is cleaned up, the task that created it might already be
gone. If the task was gone, the xdp_umem_release function did not free
the pages member of struct xdp_umem.
It turned out that the task lookup was not needed at all; The code was
a left-over when we moved from task accounting to user accounting [1].
This patch fixes the memory leak by removing the task lookup logic
completely.
[1] https://lore.kernel.org/netdev/
20180131135356.19134-3-bjorn.topel@gmail.com/
Link: https://lore.kernel.org/netdev/c1cb2ca8-6a14-3980-8672-f3de0bb38dfd@suse.cz/
Fixes: c0c77d8fb787 ("xsk: add user memory registration support sockopt")
Reported-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Eric Dumazet [Fri, 15 Mar 2019 03:19:47 +0000 (20:19 -0700)]
tun: properly test for IFF_UP
Same reasons than the ones explained in commit
4179cb5a4c92
("vxlan: test dev->flags & IFF_UP before calling netif_rx()")
netif_rx_ni() or napi_gro_frags() must be called under a strict contract.
At device dismantle phase, core networking clears IFF_UP
and flush_all_backlogs() is called after rcu grace period
to make sure no incoming packet might be in a cpu backlog
and still referencing the device.
A similar protocol is used for gro layer.
Most drivers call netif_rx() from their interrupt handler,
and since the interrupts are disabled at device dismantle,
netif_rx() does not have to check dev->flags & IFF_UP
Virtual drivers do not have this guarantee, and must
therefore make the check themselves.
Fixes: 1bd4978a88ac ("tun: honor IFF_UP in tun_get_user()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jerome Brunet [Thu, 14 Mar 2019 13:49:45 +0000 (14:49 +0100)]
net: phy: meson-gxl: fix interrupt support
If an interrupt is already pending when the interrupt is enabled on the
GXL phy, no IRQ will ever be triggered.
The fix is simply to make sure pending IRQs are cleared before setting
up the irq mask.
Fixes: cf127ff20af1 ("net: phy: meson-gxl: add interrupt support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pedro Tammela [Thu, 14 Mar 2019 13:45:23 +0000 (10:45 -0300)]
net: add documentation to socket.c
Adds missing sphinx documentation to the
socket.c's functions. Also fixes some whitespaces.
I also changed the style of older documentation as an
effort to have an uniform documentation style.
Signed-off-by: Pedro Tammela <pctammela@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kangjie Lu [Fri, 15 Mar 2019 04:12:06 +0000 (23:12 -0500)]
net: strparser: fix a missing check for create_singlethread_workqueue
In case create_singlethread_workqueue fails, the check returns
an error to callers to avoid potential NULL pointer dereferences.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Thu, 14 Mar 2019 23:56:35 +0000 (23:56 +0000)]
net: sis900: fix indentation issues, remove some spaces
There are several statements that contain extra spacing in
the indentation; clean this up by removing spaces. Also
add { } braces on if statement to keep to kernel coding
style.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Thu, 14 Mar 2019 23:47:13 +0000 (23:47 +0000)]
drivers: net: atp: fix various indentation issues
There is a statement that is indented incorrectly; replace
spaces with a tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Toke Høiland-Jørgensen [Thu, 14 Mar 2019 22:08:22 +0000 (23:08 +0100)]
sch_cake: Interpret fwmark parameter as a bitmask
We initially interpreted the fwmark parameter as a flag that simply turned
on the feature, using the whole skb->mark field as the index into the CAKE
tin_order array. However, it is quite common for different applications to
use different parts of the mask field for their own purposes, each using a
different mask.
Support this use of subsets of the mark by interpreting the TCA_CAKE_FWMARK
parameter as a bitmask to apply to the fwmark field when reading it. The
result will be right-shifted by the number of unset lower bits of the mask
before looking up the tin.
In the original commit message we also failed to credit Felix Resch with
originally suggesting the fwmark feature back in 2017; so the Suggested-By
in this commit covers the whole fwmark feature.
Fixes: 0b5c7efdfc6e ("sch_cake: Permit use of connmarks as tin classifiers")
Suggested-by: Felix Resch <fuller@beif.de>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aditya Pakki [Thu, 14 Mar 2019 20:31:40 +0000 (15:31 -0500)]
qlcnic: Avoid potential NULL pointer dereference
netdev_alloc_skb can fail and return a NULL pointer which is
dereferenced without a check. The patch avoids such a scenario.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aaro Koskinen [Thu, 14 Mar 2019 19:43:20 +0000 (21:43 +0200)]
net: stmmac: fix jumbo frame sending with non-linear skbs
When sending non-linear skbs with jumbo frames, we set up the non-paged
data and mark that as a last segment, although the paged fragments are
also prepared. This will stall the TX queue and trigger a watchdog warning
(a simple reproducer is to run an iperf client mode TCP test with a large
MTU - networking fails instantly).
Fix by checking if the skb is non-linear.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aaro Koskinen [Thu, 14 Mar 2019 19:43:19 +0000 (21:43 +0200)]
net: stmmac: don't set own bit too early for jumbo frames
Commit
0e80bdc9a72d ("stmmac: first frame prep at the end of xmit
routine") overlooked jumbo frames when re-ordering the code, and as a
result the own bit was not getting set anymore for the first jumbo frame
descriptor. Commit
487e2e22ab79 ("net: stmmac: Set OWN bit for jumbo
frames") tried to fix this, but now the bit is getting set too early and
the DMA may start while we are still setting up the remaining descriptors.
And with the chain mode the own bit remains still unset.
Fix by setting the own bit at the end of xmit also with jumbo frames.
Fixes: 0e80bdc9a72d ("stmmac: first frame prep at the end of xmit routine")
Fixes: 487e2e22ab79 ("net: stmmac: Set OWN bit for jumbo frames")
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Thu, 14 Mar 2019 05:47:59 +0000 (13:47 +0800)]
appletalk: Fix potential NULL pointer dereference in unregister_snap_client
register_snap_client may return NULL, all the callers
check it, but only print a warning. This will result in
NULL pointer dereference in unregister_snap_client and other
places.
It has always been used like this since v2.6
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 14 Mar 2019 22:10:10 +0000 (15:10 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge misc patches from Andrew Morton:
- a little bit more MM
- a few fixups
[ The "little bit more MM" is actually just one of the three patches
Andrew sent for mm/filemap.c, I'm still mulling over two more of them
from Josef Bacik - Linus ]
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
include/linux/swap.h: use offsetof() instead of custom __swapoffset macro
tools/testing/selftests/proc/proc-pid-vm.c: test with vsyscall in mind
zram: default to lzo-rle instead of lzo
filemap: pass vm_fault to the mmap ra helpers
Pi-Hsun Shih [Wed, 13 Mar 2019 18:44:33 +0000 (11:44 -0700)]
include/linux/swap.h: use offsetof() instead of custom __swapoffset macro
Use offsetof() to calculate offset of a field to take advantage of
compiler built-in version when possible, and avoid UBSAN warning when
compiling with Clang:
UBSAN: Undefined behaviour in mm/swapfile.c:3010:38
member access within null pointer of type 'union swap_header'
CPU: 6 PID: 1833 Comm: swapon Tainted: G S 4.19.23 #43
Call trace:
dump_backtrace+0x0/0x194
show_stack+0x20/0x2c
__dump_stack+0x20/0x28
dump_stack+0x70/0x94
ubsan_epilogue+0x14/0x44
ubsan_type_mismatch_common+0xf4/0xfc
__ubsan_handle_type_mismatch_v1+0x34/0x54
__se_sys_swapon+0x654/0x1084
__arm64_sys_swapon+0x1c/0x24
el0_svc_common+0xa8/0x150
el0_svc_compat_handler+0x2c/0x38
el0_svc_compat+0x8/0x18
Link: http://lkml.kernel.org/r/20190312081902.223764-1-pihsun@chromium.org
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexey Dobriyan [Wed, 13 Mar 2019 18:44:29 +0000 (11:44 -0700)]
tools/testing/selftests/proc/proc-pid-vm.c: test with vsyscall in mind
: selftests: proc: proc-pid-vm
: ========================================
: proc-pid-vm: proc-pid-vm.c:277: main: Assertion `rv == strlen(buf0)' failed.
: Aborted
Because the vsyscall mapping is enabled. Read from vsyscall page to tell
if vsyscall is being used.
Link: http://lkml.kernel.org/r/20190307183204.GA11405@avx2
Link: http://lkml.kernel.org/r/20190219094722.GB28258@shao2-debian
Fixes: 34aab6bec23e7e9 ("proc: test /proc/*/maps, smaps, smaps_rollup, statm")
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Reported-by: kernel test robot <rong.a.chen@intel.com>
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Rodgman [Wed, 13 Mar 2019 18:44:26 +0000 (11:44 -0700)]
zram: default to lzo-rle instead of lzo
lzo-rle gives higher performance and similar compression ratios to lzo.
Link: http://lkml.kernel.org/r/20190205155944.16007-4-dave.rodgman@arm.com
Signed-off-by: Dave Rodgman <dave.rodgman@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Josef Bacik [Wed, 13 Mar 2019 18:44:18 +0000 (11:44 -0700)]
filemap: pass vm_fault to the mmap ra helpers
All of the arguments to these functions come from the vmf.
Cut down on the amount of arguments passed by simply passing in the vmf
to these two helpers.
Link: http://lkml.kernel.org/r/20181211173801.29535-3-josef@toxicpanda.com
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexei Starovoitov [Thu, 14 Mar 2019 21:03:21 +0000 (14:03 -0700)]
Merge branch 'fix-bpf-docs'
Quentin Monnet says:
====================
Hi,
This set is an update to the documentation for the BPF helper functions in
the UAPI header bpf.h, used to generate the bpf-helpers(7) man page.
First patch contains fixes to the current documentation. The second patch
adds documentation for the two helpers bpf_spin_lock() and
bpf_spin_unlock(). The last patch simply reports the changes to the version
of that header in tools/.
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Quentin Monnet [Thu, 14 Mar 2019 12:38:41 +0000 (12:38 +0000)]
tools: bpf: synchronise BPF UAPI header with tools
Synchronise the bpf.h header under tools, to report the latest fixes and
additions to the documentation for the BPF helpers.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Quentin Monnet [Thu, 14 Mar 2019 12:38:40 +0000 (12:38 +0000)]
bpf: add documentation for helpers bpf_spin_lock(), bpf_spin_unlock()
Add documentation for the BPF spinlock-related helpers to the doc in
bpf.h. I added the constraints and restrictions coming with the use of
spinlocks for BPF: not all of it is directly related to the use of the
helper, but I thought it would be nice for users to find them in the man
page.
This list of restrictions is nearly a verbatim copy of the list in
Alexei's commit log for those helpers.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Quentin Monnet [Thu, 14 Mar 2019 12:38:39 +0000 (12:38 +0000)]
bpf: fix documentation for eBPF helpers
Another round of minor fixes for the documentation of the BPF helpers
located in the UAPI bpf.h header file. Changes include:
- Moving around description of some helpers, to keep the descriptions in
the same order as helpers are declared (bpf_map_push_elem(), leftover
from commit
90b1023f68c7 ("bpf: fix documentation for eBPF helpers"),
bpf_rc_keydown(), and bpf_skb_ancestor_cgroup_id()).
- Fixing typos ("contex" -> "context").
- Harmonising return types ("void* " -> "void *", "uint64_t" -> "u64").
- Addition of the "bpf_" prefix to bpf_get_storage().
- Light additions of RST markup on some keywords.
- Empty line deletion between description and return value for
bpf_tcp_sock().
- Edit for the description for bpf_skb_ecn_set_ce() (capital letters,
acronym expansion, no effect if ECT not set, more details on return
value).
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Alexei Starovoitov [Thu, 14 Mar 2019 20:53:19 +0000 (13:53 -0700)]
Merge branch 'fix-fwd-enum-resolution'
Andrii Nakryiko says:
====================
This patchset adds ability to resolve forward-declared enums into their
corresponding full enum definition types during type deduplication,
eliminating one of the reasons for having duplicated graphs of types.
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Andrii Nakryiko [Mon, 11 Mar 2019 00:44:10 +0000 (17:44 -0700)]
selftests/bpf: add fwd enum resolution test for btf_dedup
This patch adds test verifying new btf_dedup logic of resolving
forward-declared enums.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Andrii Nakryiko [Mon, 11 Mar 2019 00:44:09 +0000 (17:44 -0700)]
btf: resolve enum fwds in btf_dedup
GCC and clang support enum forward declarations as an extension. Such
forward-declared enums will be represented as normal BTF_KIND_ENUM types with
vlen=0. This patch adds ability to resolve such enums to their corresponding
fully defined enums. This helps to avoid duplicated BTF type graphs which only
differ by some types referencing forward-declared enum vs full enum.
One such example in kernel is enum irqchip_irq_state, defined in
include/linux/interrupt.h and forward-declared in include/linux/irq.h. This
causes entire struct task_struct and all referenced types to be duplicated in
btf_dedup output. This patch eliminates such duplication cases.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Linus Torvalds [Thu, 14 Mar 2019 17:48:14 +0000 (10:48 -0700)]
Merge tag 'acpi-5.1-rc1-2' of git://git./linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These fix a couple of issues and do some cleanups on top of the
previous ACPI changes for 5.1-rc1.
Specifics:
- Fix a crash caused by unloading an SSDT overlay (Andy Shevchenko)
- Prevent user space from getting confusing error values on failing
ACPI sysfs accesses (Rafael Wysocki)
- Simplify leaf node detection in the PPTT parsing code by using a
new flag defined in ACPI 6.3 (Jeremy Linton)
- Add missing "static" in some places in the ACPI configfs code (Andy
Shevchenko)
- Fix acpidbg tool path in the ACPI documentation (Flavio Suligoi)"
* tag 'acpi-5.1-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: sysfs: Prevent get_status() from returning acpi_status
ACPI / device_sysfs: Avoid OF modalias creation for removed device
ACPI / configfs: Mark local data structures static
ACPI / configfs: Mark local functions static
ACPI: tables: Simplify PPTT leaf node detection
ACPI: Documentation: Fix path for acpidbg tool
Linus Torvalds [Thu, 14 Mar 2019 17:30:06 +0000 (10:30 -0700)]
Merge tag 'pm-5.1-rc1-2' of git://git./linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These are mostly fixes and cleanups on top of the previously merged
power management material for 5.1-rc1 with one cpupower utility update
that wasn't pushed earlier due to unfortunate timing.
Specifics:
- Fix registration of new cpuidle governors partially broken during
the 5.0 development cycle by mistake (Rafael Wysocki).
- Avoid integer overflows in the menu cpuidle governor by making it
discard the overflowing data points upfront (Rafael Wysocki).
- Fix minor mistake in the recent update of the iowait boost
computation in the intel_pstate driver (Rafael Wysocki).
- Drop incorrect __init annotation from one function in the pxa2xx
cpufreq driver (Arnd Bergmann).
- Fix the operating performance points (OPP) framework initialization
for devices in multiple power domains if only one of them is
scalable (Rajendra Nayak).
- Fix mistake in dev_pm_opp_set_rate() which causes it to skip
updating the performance state if the new frequency is the same as
the old one (Viresh Kumar).
- Rework the cancellation of wakeup source timers to avoid potential
issues with it and do some cleanups unlocked by that change (Viresh
Kumar, Rafael Wysocki).
- Clean up the code computing the active/suspended time of devices in
the PM-runtime framework after recent changes (Ulf Hansson).
- Make the power management infrastructure code use pr_fmt()
consistently (Joe Perches).
- Clean up the generic power domains (genpd) framework somewhat
(Aisheng Dong).
- Improve kerneldoc comments for two functions in the cpufreq core
(Rafael Wysocki).
- Fix typo in a PM QoS file description comment (Aisheng Dong).
- Update the handling of CPU boost frequencies in the cpupower
utility (Abhishek Goel)"
* tag 'pm-5.1-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: governor: Add new governors to cpuidle_governors again
cpufreq: intel_pstate: Fix up iowait_boost computation
PM / OPP: Update performance state when freq == old_freq
PM / wakeup: Drop wakeup_source_drop()
PM / wakeup: Rework wakeup source timer cancellation
PM / domains: Remove one unnecessary blank line
PM / Domains: Return early for all errors in _genpd_power_off()
PM / Domains: Improve warn for multiple states but no governor
OPP: Fix handling of multiple power domains
PM / QoS: Fix typo in file description
cpufreq: pxa2xx: remove incorrect __init annotation
PM-runtime: Call pm_runtime_active|suspended_time() from sysfs
PM-runtime: Consolidate code to get active/suspended time
PM: Add and use pr_fmt()
cpufreq: Improve kerneldoc comments for cpufreq_cpu_get/put()
cpuidle: menu: Avoid overflows when computing variance
tools/power/cpupower: Display boost frequency separately
Linus Torvalds [Thu, 14 Mar 2019 17:27:47 +0000 (10:27 -0700)]
Merge tag 'microblaze-v5.1-rc1' of git://git.monstr.eu/linux-2.6-microblaze
Pull Microblaze update from Michal Simek:
"Simplify debugfs initialization"
* tag 'microblaze-v5.1-rc1' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: no need to check return value of debugfs_create functions
Linus Torvalds [Thu, 14 Mar 2019 16:28:12 +0000 (09:28 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
"More fixes in the queue:
1) Netfilter nat can erroneously register the device notifier twice,
fix from Florian Westphal.
2) Use after free in nf_tables, from Pablo Neira Ayuso.
3) Parallel update of steering rule fix in mlx5 river, from Eli
Britstein.
4) RX processing panic in lan743x, fix from Bryan Whitehead.
5) Use before initialization of TCP_SKB_CB, fix from Christoph Paasch.
6) Fix locking in SRIOV mode of mlx4 driver, from Jack Morgenstein.
7) Fix TX stalls in lan743x due to mishandling of interrupt ACKing
modes, from Bryan Whitehead.
8) Fix infoleak in l2tp_ip6_recvmsg(), from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
pptp: dst_release sk_dst_cache in pptp_sock_destruct
MAINTAINERS: GENET & SYSTEMPORT: Add internal Broadcom list
l2tp: fix infoleak in l2tp_ip6_recvmsg()
net/tls: Inform user space about send buffer availability
net_sched: return correct value for *notify* functions
lan743x: Fix TX Stall Issue
net/mlx4_core: Fix qp mtt size calculation
net/mlx4_core: Fix locking in SRIOV mode when switching between events and polling
net/mlx4_core: Fix reset flow when in command polling mode
mlxsw: minimal: Initialize base_mac
mlxsw: core: Prevent duplication during QSFP module initialization
net: dwmac-sun8i: fix a missing check of of_get_phy_mode
net: sh_eth: fix a missing check of of_get_phy_mode
net: 8390: fix potential NULL pointer dereferences
net: fujitsu: fix a potential NULL pointer dereference
net: qlogic: fix a potential NULL pointer dereference
isdn: hfcpci: fix potential NULL pointer dereference
Documentation: devicetree: add a new optional property for port mac address
net: rocker: fix a potential NULL pointer dereference
net: qlge: fix a potential NULL pointer dereference
...
Linus Torvalds [Thu, 14 Mar 2019 16:11:54 +0000 (09:11 -0700)]
Merge tag 'dmaengine-5.1-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- dmatest updates for modularizing common struct and code
- remove SG support for VDMA xilinx IP and updates to driver
- Update to dw driver to support Intel iDMA controllers multi-block
support
- tegra updates for proper reporting of residue
- Add Snow Ridge ioatdma device id and support for IOATDMA v3.4
- struct_size() usage and useless LIST_HEAD cleanups in subsystem.
- qDMA controller driver for Layerscape SoCs
- stm32-dma PM Runtime support
- And usual updates to imx-sdma, sprd, Documentation, fsl-edma,
bcm2835, qcom_hidma etc
* tag 'dmaengine-5.1-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (81 commits)
dmaengine: imx-sdma: fix consistent dma test failures
dmaengine: imx-sdma: add a test for imx8mq multi sdma devices
dmaengine: imx-sdma: add clock ratio 1:1 check
dmaengine: dmatest: move test data alloc & free into functions
dmaengine: dmatest: add short-hand `buf_size` var in dmatest_func()
dmaengine: dmatest: wrap src & dst data into a struct
dmaengine: ioatdma: support latency tolerance report (LTR) for v3.4
dmaengine: ioatdma: add descriptor pre-fetch support for v3.4
dmaengine: ioatdma: disable DCA enabling on IOATDMA v3.4
dmaengine: ioatdma: Add Snow Ridge ioatdma device id
dmaengine: sprd: Change channel id to slave id for DMA cell specifier
dt-bindings: dmaengine: sprd: Change channel id to slave id for DMA cell specifier
dmaengine: mv_xor: Use correct device for DMA API
Documentation :dmaengine: clarify DMA desc. pointer after submission
Documentation: dmaengine: fix dmatest.rst warning
dmaengine: k3dma: Add support for dma-channel-mask
dmaengine: k3dma: Delete axi_config
dmaengine: k3dma: Upgrade k3dma driver to support hisi_asp_dma hardware
Documentation: bindings: dma: Add binding for dma-channel-mask
Documentation: bindings: k3dma: Extend the k3dma driver binding to support hisi-asp
...
Linus Torvalds [Thu, 14 Mar 2019 16:00:06 +0000 (09:00 -0700)]
Merge tag 'rproc-v5.1' of git://github.com/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"This contains the last patches in Loic's remoteproc resource table
handling changes, a number of updates to documentation, support for
invoking the crash handler (for testing purposes), a fix for the
handling of virtio devices during recovery, performance state votes in
Qualcomm modem driver, support for specifying board specific firmware
path for Qualcomm modem driver and improved support for graceful
shutdown of Qualcomm remoteprocs"
* tag 'rproc-v5.1' of git://github.com/andersson/remoteproc: (33 commits)
remoteproc: fix for "dma-mapping: remove the DMA_MEMORY_EXCLUSIVE flag"
remoteproc: fix rproc_check_carveout_da() returned error and comments
remoteproc: fix trace buffer va initialization
remoteproc: fix rproc_alloc_carveout() for rproc with iommu domain
remoteproc: add warning on resource table cast
remoteproc: fix rproc_alloc_carveout() bad variable cast
remoteproc: fix rproc_da_to_va in case of unallocated carveout
remoteproc: correct rproc_mem_entry_init() comments
remoteproc: fix recovery procedure
rpmsg: virtio: change header file sort style
rpmsg: virtio: allocate buffer from parent
remoteproc: st: add reserved memory support
remoteproc: create vdev subdevice with specific dma memory pool
remoteproc: q6v5_adsp: Remove voting for lpass_aon clock
dt-binding: remoteproc: Remove lpass_aon clock from adsp pil clock list
remoteproc: q6v5-mss: Active powerdomain for SDM845
remoteproc: q6v5-mss: Vote for rpmh power domains
remoteproc: qcom: Add support for parsing fw dt bindings
remoteproc: qcom_q6v5: don't auto boot remote processor
remoteproc: qcom: Wait for shutdown-ack/ind on sysmon shutdown
...
Linus Torvalds [Thu, 14 Mar 2019 15:46:17 +0000 (08:46 -0700)]
Merge tag 'clk-for-linus' of git://git./linux/kernel/git/clk/linux
Pull clk subsystem updates from Stephen Boyd:
"We have a fairly balanced mix of clk driver updates and clk framework
updates this time around. It's the usual pile of new drivers for new
hardware out there and the normal small fixes and updates, but then we
have some core framework changes too.
In the core framework, we introduce support for a clk_get_optional()
API to get clks that may not always be populated and a way to devm
manage clkdev lookups registered by provider drivers. We also do some
refactoring to simplify the interface between clkdev and the common
clk framework so we can reuse the DT parsing and clk_get() path in
provider drivers in the future. This work will continue in the next
few cycles while we convert how providers specify clk parents.
On the driver side, the biggest part of the dirstat is the Amlogic clk
driver that got support for the G12A SoC. It dominates with almost
half the overall diff, while the second largest part of the diff is in
the i.MX clk driver that gained support for imx8mm SoCs. After that,
we have the Actions Semiconductor and Qualcomm drivers rounding out
the big part of the dirstat because they both got new hardware support
for SoCs. The rest is just various updates and non-critical fixes for
existing drivers.
Core:
- Convert a few clk bindings to JSON schema format
- Add a {devm_}clk_get_optional() API
- Add devm_clk_hw_register_clkdev() API to manage clkdev lookups
- Start rewriting clk parent registration and supporting device links
by moving around code that supports clk_get() and DT parsing of the
'clocks' property
New Drivers:
- Add Qualcomm MSM8998 RPM managed clks
- IPA clk support on Qualcomm RPMh clk controllers
- Actions Semi S500 SoC clk support
- Support for fixed rate clks populated from an MMIO register
- Add RPC (QSPI/HyperFLASH) clocks on Renesas R-Car V3H
- Add TMU (timer) clocks on Renesas RZ/G2E
- Add Amlogic G12A Always-On Clock Controller
- Add 32k clock generation for Amlogic AXG
- Add support for the Mali GPU clocks on Amlogic Meson8
- Add Amlogic G12A EE clock controller driver
- Add missing CANFD clocks on Renesas RZ/G2M and RZ/G2E
- Add i.MX8MM SoC clk driver support
Removed Drivers:
- Remove clps711x driver as the board support is gone
Updates:
- 3rd ECO fix for Mediatek MT2712 SoCs
- Updates for Qualcomm MSM8998 GCC clks
- Random static analysis fixes for clk drivers
- Support for sleeping gpios in the clk-gpio type
- Minor fixes for STM32MP1 clk driver (parents, critical flag, etc.)
- Split LCDC into two clks on the Marvell MMP2 SoC
- Various DT of_node refcount fixes
- Get rid of CLK_IS_BASIC from TI code (yay!)
- TI Autoidle clk support
- Fix Amlogic Meson8 APB clock ID name
- Claim input clocks through DT for Amlogic AXG and GXBB
- Correct the DU (display unit) parent clock on Renesas RZ/G2E
- Exynos5433 IMEM CMU crypto clk support (SlimSS)
- Fix for the PLL-MIPI on the Allwinner A23
- Fix Rockchip rk3328 PLL rate calculation
- Add SET_RATE_PARENT flag on display clk of Rockhip rk3066
- i.MX SCU clk driver clk_set_parent() and cpufreq support"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (150 commits)
dt-bindings: clock: imx8mq: Fix numbering overlaps and gaps
clk: ti: clkctrl: Fix clkdm_name regression for TI_CLK_CLKCTRL_COMPAT
clk: fixup default index for of_clk_get_by_name()
clk: Move of_clk_*() APIs into clk.c from clkdev.c
clk: Inform the core about consumer devices
clk: Introduce of_clk_get_hw_from_clkspec()
clk: core: clarify the check for runtime PM
clk: Combine __clk_get() and __clk_create_clk()
clk: imx8mq: add GPIO clocks to clock tree
clk: mediatek: correct cpu clock name for MT8173 SoC
clk: imx: Refactor entire sccg pll clk
clk: imx: scu: add cpu frequency scaling support
clk: mediatek: Mark bus and DRAM related clocks as critical
clk: mediatek: Add flags to mtk_gate
clk: mediatek: Add MUX_FLAGS macro
clk: qcom: gcc-sdm845: Define parent of PCIe PIPE clocks
clk: ingenic: Remove set but not used variable 'enable'
clk: at91: programmable: remove unneeded register read
clk: mediatek: using CLK_MUX_ROUND_CLOSEST for the clock of dpi1_sel
clk: mediatek: add MUX_GATE_FLAGS_2
...
Rafael J. Wysocki [Thu, 14 Mar 2019 09:54:28 +0000 (10:54 +0100)]
Merge branches 'acpi-tables', 'acpi-debug', 'acpi-doc' and 'acpi-misc'
* acpi-tables:
ACPI: tables: Simplify PPTT leaf node detection
* acpi-debug:
ACPI: sysfs: Prevent get_status() from returning acpi_status
* acpi-doc:
ACPI: Documentation: Fix path for acpidbg tool
* acpi-misc:
ACPI / configfs: Mark local data structures static
ACPI / configfs: Mark local functions static
Rafael J. Wysocki [Thu, 14 Mar 2019 09:53:22 +0000 (10:53 +0100)]
Merge branches 'pm-opp' and 'pm-tools'
* pm-opp:
PM / OPP: Update performance state when freq == old_freq
OPP: Fix handling of multiple power domains
* pm-tools:
tools/power/cpupower: Display boost frequency separately
Rafael J. Wysocki [Thu, 14 Mar 2019 09:53:08 +0000 (10:53 +0100)]
Merge branch 'pm-domains'
* pm-domains:
PM / domains: Remove one unnecessary blank line
PM / Domains: Return early for all errors in _genpd_power_off()
PM / Domains: Improve warn for multiple states but no governor
Rafael J. Wysocki [Thu, 14 Mar 2019 09:51:51 +0000 (10:51 +0100)]
Merge branches 'pm-cpuidle' and 'pm-cpufreq'
* pm-cpuidle:
cpuidle: governor: Add new governors to cpuidle_governors again
cpuidle: menu: Avoid overflows when computing variance
* pm-cpufreq:
cpufreq: intel_pstate: Fix up iowait_boost computation
cpufreq: pxa2xx: remove incorrect __init annotation
cpufreq: Improve kerneldoc comments for cpufreq_cpu_get/put()
Rafael J. Wysocki [Thu, 14 Mar 2019 09:51:38 +0000 (10:51 +0100)]
Merge branches 'pm-core', 'pm-sleep' and 'pm-qos'
* pm-core:
PM-runtime: Call pm_runtime_active|suspended_time() from sysfs
PM-runtime: Consolidate code to get active/suspended time
* pm-sleep:
PM / wakeup: Drop wakeup_source_drop()
PM / wakeup: Rework wakeup source timer cancellation
* pm-qos:
PM / QoS: Fix typo in file description
Xin Long [Wed, 13 Mar 2019 09:00:48 +0000 (17:00 +0800)]
pptp: dst_release sk_dst_cache in pptp_sock_destruct
sk_setup_caps() is called to set sk->sk_dst_cache in pptp_connect,
so we have to dst_release(sk->sk_dst_cache) in pptp_sock_destruct,
otherwise, the dst refcnt will leak.
It can be reproduced by this syz log:
r1 = socket$pptp(0x18, 0x1, 0x2)
bind$pptp(r1, &(0x7f0000000100)={0x18, 0x2, {0x0, @local}}, 0x1e)
connect$pptp(r1, &(0x7f0000000000)={0x18, 0x2, {0x3, @remote}}, 0x1e)
Consecutive dmesg warnings will occur:
unregister_netdevice: waiting for lo to become free. Usage count = 1
v1->v2:
- use rcu_dereference_protected() instead of rcu_dereference_check(),
as suggested by Eric.
Fixes: 00959ade36ac ("PPTP: PPP over IPv4 (Point-to-Point Tunneling Protocol)")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / openwrt / staging / blogic.git / log