openwrt/staging/blogic.git
15 years agodavinci: cleanup: move dm355 UART2 define to dm355.c
Kevin Hilman [Thu, 30 Apr 2009 18:20:24 +0000 (11:20 -0700)]
davinci: cleanup: move dm355 UART2 define to dm355.c

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agodavinci: Move PINMUX defines to SoC files
Mark A. Greer [Wed, 15 Apr 2009 19:42:06 +0000 (12:42 -0700)]
davinci: Move PINMUX defines to SoC files

Different SoC have different numbers of pinmux registers and other
resources that overlap with each other.  To clean up the code and
eliminate defines that overlap with each other, move the PINMUX
defines to the SoC specific files.

Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agodavinci: Add compare register support to timer code
Mark A. Greer [Wed, 15 Apr 2009 19:41:54 +0000 (12:41 -0700)]
davinci: Add compare register support to timer code

The Timer64p timer has 8 compare registers that can
be used to generate interrupts when the timer value
matches the compare reg's value.  They do not disturb
the timer itself.  This can be useful when there is
only one timer available for both clock events and
clocksource.

When enabled, the clocksource remains a continuous
32-bit counter but the clock event will no longer
support periodic interrupts.  Instead only oneshot
timers will be supported and implemented by setting
the compare register to the current timer value plus
the period that the clock event subsystem is requesting.

Compare registers support is enabled automatically
when the following conditions are met:
1) The same timer is being used for clock events
   and clocksource.
2) The timer is the bottom half (32 bits) of the
   64-bit timer (hardware limitation).
3) The the compare register offset and irq are
   not zero.

Since the timer is always running, there is a hardware
race in timer32_config() between reading the current
timer value, and adding the period to the current
timer value and writing the compare register.
Testing on a da830 evm board with the timer clocked
at 24 MHz and the processor clocked at 300 MHz,
showed the number of counter ticks to do this ranged
from 20-53 (~1-2.2 usecs) but usually around 41 ticks.
This includes some artifacts from collecting the
information.  So, the minimum period should be
at least 5 usecs to be safe.

There is also an non-critical lower limit that
the period should be since there is no point in
setting an event that is much shorter than the
time it takes to set the event, and get & handle
the timer interrupt for that event.  There can
also be all sorts of delays from activities
occuring elsewhere in the system (including
hardware activitis like cache & TLB management).
These are virtually impossible to quantify so a
minimum period of 50 usecs was chosen.  That will
certianly be enough to avoid the actual hardware
race but hopefully not large enough to cause
unreasonably course-grained timers.

Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agodavinci: Integrate cp_intc support into low-level irq code
Mark A. Greer [Wed, 15 Apr 2009 19:41:40 +0000 (12:41 -0700)]
davinci: Integrate cp_intc support into low-level irq code

Integrate the Common Platform Interrupt Controller (cp_intc)
support into the low-level irq handling for davinci and similar
platforms.  Do it such that support for cp_intc and the original
aintc can coexist in the same kernel binary.

Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agodavinci: Factor out emac mac address handling
Mark A. Greer [Wed, 15 Apr 2009 19:41:27 +0000 (12:41 -0700)]
davinci: Factor out emac mac address handling

Factor out the code to extract that mac address from
i2c eeprom.

Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agodavinci: Remove unused i2c eeprom_read/write routines
Mark A. Greer [Wed, 15 Apr 2009 19:41:15 +0000 (12:41 -0700)]
davinci: Remove unused i2c eeprom_read/write routines

The dm644x and dm646x board files have i2c eeprom read and
write routines but they are not used so remove them.

Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agodavinci: Move emac platform_data to SoC-specific files
Mark A. Greer [Wed, 15 Apr 2009 19:40:56 +0000 (12:40 -0700)]
davinci: Move emac platform_data to SoC-specific files

Since most of the emac platform_data is really SoC specific
and not board specific, move it to the SoC-specific files.
Put a pointer to the platform_data in the soc_info structure
so the board-specific code can set some of the platform_data
if it needs to.

Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agodavinci: Move serial platform_device into SoC-specific files
Mark A. Greer [Wed, 18 Mar 2009 17:36:08 +0000 (12:36 -0500)]
davinci: Move serial platform_device into SoC-specific files

Currently, there is one set of platform_device and platform_data
structures for all DaVinci SoCs.  The differences in the data
between the various SoCs is handled by davinci_serial_init()
by checking the SoC type.  However, as new SoCs appear, this
routine will become more & more cluttered.

To clean up the routine and make it easier to add support for new
SoCs, move the platform_device and platform_data structures into the
SoC-specific code and use the SoC infrastructure to provide access
to the data.

In the process, fix a bug where the wrong irq is used for uart2
of the dm646x.

Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agodavinci: Make GPIO code more generic
Mark A. Greer [Wed, 15 Apr 2009 19:40:35 +0000 (12:40 -0700)]
davinci: Make GPIO code more generic

The current gpio code needs to know the number of
gpio irqs there are and what the bank irq number is.
To determine those values, it checks the SoC type.

It also assumes that the base address and the number
of irqs the interrupt controller uses is fixed.

To clean up the SoC checks and make it support
different base addresses and interrupt controllers,
have the SoC-specific code set those values in
the soc_info structure and have the gpio code
reference them there.

Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agodavinci: Add watchdog base address flexibility
Mark A. Greer [Wed, 15 Apr 2009 19:40:21 +0000 (12:40 -0700)]
davinci: Add watchdog base address flexibility

The watchdog code currently hardcodes the base address
of the timer its using.  To support new SoCs, make it
support timers at any address.  Use the soc_info structure
to do this.

Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agodavinci: Add base address and timer flexibility
Mark A. Greer [Wed, 15 Apr 2009 19:40:11 +0000 (12:40 -0700)]
davinci: Add base address and timer flexibility

The davinci timer code currently hardcodes the timer register
base addresses, the timer irq numbers, and the timers to use
for clock events and clocksource.  This won't work for some
a new SoC so put those values into the soc_info structure
and set them up in the SoC-specific files.

Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agodavinci: Move interrupt ctlr info to SoC infrastructure
Mark A. Greer [Wed, 15 Apr 2009 19:40:00 +0000 (12:40 -0700)]
davinci: Move interrupt ctlr info to SoC infrastructure

Use the SoC infrastructure to hold the interrupt controller
information (i.e., base address, default priorities,
interrupt controller type, and the number of IRQs).

The interrupt controller base, although initially put
in the soc_info structure's intc_base field, is eventually
put in the global 'davinci_intc_base' so the low-level
interrupt code can access it without a dereference.

These changes enable the SoC default irq priorities to be
put in the SoC-specific files, and the interrupt controller
to be at any base address.

Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agodavinci: Move pinmux setup info to SoC infrastructure
Mark A. Greer [Wed, 15 Apr 2009 19:39:48 +0000 (12:39 -0700)]
davinci: Move pinmux setup info to SoC infrastructure

The pinmux register base and setup can be different for different
SoCs so move the pinmux reg base, pinmux table (and its size) to
the SoC infrastructure.

Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agodavinci: Add support for multiple PSCs
Mark A. Greer [Wed, 15 Apr 2009 19:39:33 +0000 (12:39 -0700)]
davinci: Add support for multiple PSCs

The current code to support the DaVinci Power and Sleep Controller (PSC)
assumes that there is only one controller.  This assumption is no longer
valid so expand the support to allow greater than one PSC.

To accomplish this, put the base addresses for the PSCs in the SoC
infrastructure so it can be referenced by the PSC code.  This also
requires adding an extra parameter to davinci_psc_config() to specify
the PSC that is to be enabled/disabled.

Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agodavinci: Add clock init call to common init routine
Mark A. Greer [Wed, 15 Apr 2009 19:39:23 +0000 (12:39 -0700)]
davinci: Add clock init call to common init routine

All of the davinci SoCs need to call davinci_clk_init() so
put the call in the common init routine.

Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agodavinci: Support JTAG ID register at any address
Mark A. Greer [Wed, 15 Apr 2009 19:39:09 +0000 (12:39 -0700)]
davinci: Support JTAG ID register at any address

The Davinci cpu_is_davinci_*() macros use the SoC part number
and variant retrieved from the JTAG ID register to determine the
type of cpu that the kernel is running on.  Currently, the code to
read the JTAG ID register assumes that the register is always at
the same base address.  This isn't true on some newer SoCs.

To solve this, have the SoC-specific code set the JTAG ID register
base address in soc_info structure and add a 'cpu_id' member to it.
'cpu_id' will be used by the cpu_is_davinci_*() macros to match
the cpu id.  Also move the info used to identify the cpu type into
the SoC-specific code to keep all SoC-specific code together.

The common code will read the JTAG ID register, search through
an array of davinci_id structures to identify the cpu type.
Once identified, it will set the 'cpu_id' member of the soc_info
structure to the proper value and the cpu_is_davinci_*() macros
will now work.

Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agodavinci: Encapsulate SoC-specific data in a structure
Mark A. Greer [Wed, 15 Apr 2009 19:38:58 +0000 (12:38 -0700)]
davinci: Encapsulate SoC-specific data in a structure

Create a structure to encapsulate SoC-specific information.
This will assist in generalizing code so it can be used by
different SoCs that have similar hardware but with minor
differences such as having a different base address.

The idea is that the code for each SoC fills out a structure
with the correct information.  The board-specific code then
calls the SoC init routine which in turn will call a common
init routine that makes a copy of the structure, maps in I/O
regions, etc.

After initialization, code can get a pointer to the structure
by calling davinci_get_soc_info().  Eventually, the common
init routine will make a copy of all of the data pointed to
by the structure so the original data can be made __init_data.
That way the data for SoC's that aren't being used won't consume
memory for the entire life of the kernel.

The structure will be extended in subsequent patches but
initially, it holds the map_desc structure for any I/O
regions the SoC/board wants statically mapped.

Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agodavinci: EMAC platform support
Kevin Hilman [Thu, 7 May 2009 13:19:40 +0000 (06:19 -0700)]
davinci: EMAC platform support

Add SoC and platform-specific data and init for DaVinci EMAC network
driver.

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agodavinci: MMC platform support
Kevin Hilman [Mon, 11 May 2009 22:55:03 +0000 (15:55 -0700)]
davinci: MMC platform support

Add SoC and platform-specific data and init for MMC driver.

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agodavinci: update davinci_all_defconfig for dm355, dm6467
Kevin Hilman [Wed, 20 May 2009 23:44:44 +0000 (16:44 -0700)]
davinci: update davinci_all_defconfig for dm355, dm6467

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agodavinci: DM646x: add base SoC and board support
Kevin Hilman [Thu, 30 Apr 2009 00:44:58 +0000 (17:44 -0700)]
davinci: DM646x: add base SoC and board support

Add support for DM646x SoC (a.k.a DaVinci HD) and its Evalution
Module (EVM.)

Original support done by Sudhakar Rajashekhara.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agodavinci: DM355: add base SoC and board support
Kevin Hilman [Wed, 29 Apr 2009 19:10:55 +0000 (12:10 -0700)]
davinci: DM355: add base SoC and board support

In addition, add board support for the DM355 Evaluation Module (EVM)
and the DM355 Leopard board.

Original DM355 EVM support done by Sandeep Paulraj, with significant
updates and improvements by David Brownell.  DM355 Leopord support
done by Koen Kooi.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Koen Kooi <koen@beagleboard.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agodavinci: DM644x: add support for SFFSDR board
Hugo Villeneuve [Wed, 29 Apr 2009 23:46:57 +0000 (16:46 -0700)]
davinci: DM644x: add support for SFFSDR board

Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agodavinci: add platform support for watchdog timer
Kevin Hilman [Wed, 29 Apr 2009 23:23:59 +0000 (16:23 -0700)]
davinci: add platform support for watchdog timer

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agodavinci: INTC: add support for TI cp_intc
Sergei Shtylyov [Wed, 11 Mar 2009 15:49:05 +0000 (19:49 +0400)]
davinci: INTC: add support for TI cp_intc

Add support for Texas Instuments Common Platform Interrupt Controller
(cp_intc) used on DA830/OMAP-L137.

Signed-off-by: Steve Chen <schen@mvista.com>
Signed-off-by: Mark Greer <mgreer@mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agodavinci: support different UART bases for zImage uncompress
Mark A. Greer [Wed, 18 Feb 2009 21:00:36 +0000 (14:00 -0700)]
davinci: support different UART bases for zImage uncompress

The davinci pre-kernel boot code assumes that all platforms use the
same UART base address for the console.  That assumption is not longer
valid with some newer SoCs so determine the console UART base address
from the machine number passed in from bootloader.

Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agodavinci: interrupts: get_irqnr_and_base: save an instruction
Troy Kisky [Mon, 11 Feb 2008 21:44:07 +0000 (14:44 -0700)]
davinci: interrupts: get_irqnr_and_base: save an instruction

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agodavinci: use 32-bit accesses for low-level debug macros
Chaithrika U S [Mon, 19 Jan 2009 08:43:05 +0000 (14:13 +0530)]
davinci: use 32-bit accesses for low-level debug macros

This patch defines debug macros for low-level debugging for Davinci
based platforms

Tested on :
        - DM644x DaVinci EVM
        - DM646X DaVinciHD EVM
- DM355 EVM

This patch attempts to solve the low-level debug issue in DM646x. The
UART on DM646x SoC allows only 32-bit access. The existing
debug-macro.S uses the macros from debug-8250.S file. This led to
garbage serial out in the case of DM646x.

The inclusion of debug-8250.S does not allow for run time fix for this
issue.  There are compile time errors due to multiple definitions of
the macros.  Also when building a single image for multiple DaVinci
Platforms, the ifdefs cannot be relied upon.

The solution below does not include the debug-8250.S file and defines
the necessary macros. This solution was arrived at after observing
that word access does not affect the low-level debug messages on
DM644x/DM355.

The other approach to this issue is to use the UART module information
available in the peripheral registers to decide the access
mechanism. But this will have to be done for every access of UART
specifically for DM646x. Also this calls for a modification of the
debug-8250.S file.

Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agodavinci: fixups for banked GPIO interrupt handling
Kevin Hilman [Mon, 11 May 2009 18:04:53 +0000 (11:04 -0700)]
davinci: fixups for banked GPIO interrupt handling

This patch seems to get me much more reliable performance using the
GPIO banked interrupts on dm355 for the dm9000 driver.

Changes include:

- init GPIO handling along with normal GPIO init
- mask the level-sensitive bank IRQ during handling

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agodavinci: gpio irq enable tweaks
David Brownell [Mon, 4 May 2009 20:14:27 +0000 (13:14 -0700)]
davinci: gpio irq enable tweaks

Fix two IRQ triggering bugs affecting GPIO IRQs:

 - Make sure enabling with IRQ_TYPE_NONE ("default, unspecified")
   isn't a NOP ... default to both edges, at least one must work.

 - As noted by Kevin Hilman, setting the irq trigger type for a
   banked gpio interrupt shouldn't enable irqs that are disabled.

Since GPIO IRQs haven't been used much yet, it's not clear these
bugs could have affected anything.  The few current users don't
seem to have been obviously suffering from these issues.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
15 years agoLinux 2.6.30-rc7
Linus Torvalds [Sat, 23 May 2009 21:47:00 +0000 (14:47 -0700)]
Linux 2.6.30-rc7

15 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6
Linus Torvalds [Sat, 23 May 2009 20:44:00 +0000 (13:44 -0700)]
Merge git://git./linux/kernel/git/jejb/scsi-rc-fixes-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] mpt2sas: fix driver version inconsistency
  [SCSI] 3w-xxxx: scsi_dma_unmap fix
  [SCSI] 3w-9xxx: scsi_dma_unmap fix
  [SCSI] ses: fix problems caused by empty SES provided name
  [SCSI] fc-transport: Close state transition-window during rport deletion.
  [SCSI] initialize max_target_blocked in scsi_alloc_target
  [SCSI] fnic: Add new Cisco PCI-Express FCoE HBA

15 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6
Linus Torvalds [Sat, 23 May 2009 20:42:53 +0000 (13:42 -0700)]
Merge git://git./linux/kernel/git/sfrench/cifs-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  [CIFS] Avoid open on possible directories since Samba now rejects them

15 years ago[CIFS] Avoid open on possible directories since Samba now rejects them
Steve French [Sat, 23 May 2009 18:57:25 +0000 (18:57 +0000)]
[CIFS] Avoid open on possible directories since Samba now rejects them

Small change (mostly formatting) to limit lookup based open calls to
file create only.

After discussion yesteday on samba-technical about the posix lookup
regression,  and looking at a problem with cifs posix open to one
particular Samba version, Jeff and JRA realized that Samba server's
behavior changed in this area (posix open behavior on files vs.
directories).   To make this behavior consistent, JRA just made a
fix to Samba server to alter how it handles open of directories (now
returning the equivalent of EISDIR instead of success). Since we don't
know at lookup time whether the inode is a directory or file (and
thus whether posix open will succeed with most current Samba server),
this change avoids the posix open code on lookup open (just issues
posix open on creates).    This gets the semantic benefits we want
(atomicity, posix byte range locks, improved write semantics on newly
created files) and file create still is fast, and we avoid the problem
that Jeff noticed yesterday with "openat" (and some open directory
calls) of non-cached directories to one version of Samba server, and
will work with future Samba versions (which include the fix jra just
pushed into Samba server).  I confirmed this approach with jra
yesterday and with Shirish today.

Posix open is only called (at lookup time) for file create now.
For opens (rather than creates), because we do not know if it
is a file or directory yet, and current Samba no longer allows
us to do posix open on dirs, we could end up wasting an open call
on what turns out to be a dir. For file opens, we wait to call posix
open till cifs_open.  It could be added here (lookup) in the future
but the performance tradeoff of the extra network request when EISDIR
or EACCES is returned would have to be weighed against the 50%
reduction in network traffic in the other paths.

Reviewed-by: Shirish Pargaonkar <shirishp@us.ibm.com>
Tested-by: Jeff Layton <jlayton@redhat.com>
CC: Jeremy Allison <jra@samba.org>
Signed-off-by: Steve French <sfrench@us.ibm.com>
15 years agoicom: fix rmmod crash
Breno Leitao [Sat, 23 May 2009 00:30:39 +0000 (21:30 -0300)]
icom: fix rmmod crash

Actually the icom driver is crashing when is being removed because
the driver is kfreeing the adapter structure before calling
pci_release_regions(), which result in the following error:

  Unable to handle kernel paging request for data at address 0x6b6b6b6b6b6b6d33
  Faulting instruction address: 0xc000000000246b80
  Oops: Kernel access of bad area, sig: 11 [#1]
  ....
  [c000000012d436a0] [c0000000001002d0] .kfree+0x120/0x34c (unreliable)
  [c000000012d43730] [c000000000246d60] .pci_release_selected_regions+0x3c/0x68
  [c000000012d437c0] [d000000002d54700] .icom_kref_release+0xf4/0x118 [icom]
  [c000000012d43850] [c000000000232e50] .kref_put+0x74/0x94
  [c000000012d438d0] [d000000002d56c58] .icom_remove+0x40/0xa4 [icom]
  [c000000012d43960] [c000000000249e48] .pci_device_remove+0x50/0x90
  [c000000012d439e0] [c0000000002d68d8] .__device_release_driver+0x94/0xd4
  [c000000012d43a70] [c0000000002d7104] .driver_detach+0xf8/0x12c
  [c000000012d43b00] [c0000000002d549c] .bus_remove_driver+0xbc/0x11c
  [c000000012d43b90] [c0000000002d71dc] .driver_unregister+0x60/0x80
  [c000000012d43c20] [c00000000024a07c] .pci_unregister_driver+0x44/0xe8
  [c000000012d43cb0] [d000000002d56bf4] .icom_exit+0x1c/0x40 [icom]
  [c000000012d43d30] [c000000000095fa8] .SyS_delete_module+0x214/0x2a8
  [c000000012d43e30] [c00000000000852c] syscall_exit+0x0/0x40

Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Cc: stable@kernel.org
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
Linus Torvalds [Fri, 22 May 2009 20:38:52 +0000 (13:38 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/tiwai/sound-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: Kill truncate warning by shortening Sigmatel-specific AC97 control name
  ALSA: hda - fix audio on HP TX25xx series notebooks
  ALSA: pcsp - fix printk format warning again

15 years agoMerge branch 'fix/misc' into for-linus
Takashi Iwai [Fri, 22 May 2009 17:29:08 +0000 (19:29 +0200)]
Merge branch 'fix/misc' into for-linus

* fix/misc:
  ALSA: Kill truncate warning by shortening Sigmatel-specific AC97 control name
  ALSA: pcsp - fix printk format warning again

15 years agoALSA: Kill truncate warning by shortening Sigmatel-specific AC97 control name
Andreas Mohr [Fri, 22 May 2009 15:48:58 +0000 (17:48 +0200)]
ALSA: Kill truncate warning by shortening Sigmatel-specific AC97 control name

ALSA sound/core/control.c:232: Control name 'Sigmatel Surround Phase
Inversion Playback Switch' truncated to 'Sigmatel Surround Phase
Inversion Playback ' bootup message by omitting weird Sigmatel prefix
in this case; also fix up the related ca0106 mixer control removal
part by using identical naming there.

Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
15 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke...
Linus Torvalds [Fri, 22 May 2009 15:41:13 +0000 (08:41 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ryusuke/nilfs2

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
  nilfs2: fix memory leak in nilfs_ioctl_clean_segments

15 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6
Linus Torvalds [Fri, 22 May 2009 15:22:39 +0000 (08:22 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/bart/ide-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  via82cxxx: Add VIA VX855 PCI Device ID
  ide: report timeouts in ide_busy_sleep()
  ide: improve failed opcode reporting
  ide: fix printk() levels in ide_dump_ata[pi]_error()
  ide: fix OOPS during ide-cd error recovery
  ide: fix 40-wire cable detection for TSST SH-S202* ATAPI devices (v2)

15 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6
Linus Torvalds [Fri, 22 May 2009 14:38:28 +0000 (07:38 -0700)]
Merge git://git./linux/kernel/git/sfrench/cifs-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  [CIFS] fix posix open regression

15 years agoMerge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
Linus Torvalds [Fri, 22 May 2009 14:37:42 +0000 (07:37 -0700)]
Merge branch 'upstream' of git://ftp.linux-mips.org/upstream-linus

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  MIPS: IP32: Remove unnecessary if not even harmful volatile keywords.
  MIPS: IP32: Fix build error due to uninitialized variable.
  MIPS: Fix sparse warning in incompatiable argument type of clear_user.

15 years agoMerge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Linus Torvalds [Fri, 22 May 2009 14:33:49 +0000 (07:33 -0700)]
Merge branch 'merge' of git://git./linux/kernel/git/benh/powerpc

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/maple: Add a quirk to disable MSI for IPR on Bimini

15 years agoMerge branch 'sh/for-2.6.30' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal...
Linus Torvalds [Fri, 22 May 2009 14:33:38 +0000 (07:33 -0700)]
Merge branch 'sh/for-2.6.30' of git://git./linux/kernel/git/lethal/sh-2.6

* 'sh/for-2.6.30' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  video: stop sh_mobile_lcdcfb only if started
  sh: ap325 camera without i2c driver fix

15 years agoipmi: fix ipmi_si modprobe hang
Corey Minyard [Wed, 20 May 2009 18:36:17 +0000 (13:36 -0500)]
ipmi: fix ipmi_si modprobe hang

Instead of queuing IPMB messages before channel initialization, just
throw them away.  Nobody will be listening for them at this point,
anyway, and they will clog up the queue and nothing will be delivered
if we queue them.

Also set the current channel to the number of channels, as this value
is used to tell if the channel information has been initialized.

Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Ferenc Wagner <wferi@niif.hu>
Cc: Dan Frazier <dannf@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agovia82cxxx: Add VIA VX855 PCI Device ID
Harald Welte [Fri, 22 May 2009 14:23:39 +0000 (16:23 +0200)]
via82cxxx: Add VIA VX855 PCI Device ID

This patch adds the PCI Device ID 0xc409 to the PCI ID table of via82cxxx.c,
as well as the 0x8409 south bridge ID.

This is required to make the IDE driver work on the VX855/VX875 integrated
chipset.

Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Bruce Chang <BruceChang@via.com.tw>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
15 years agoide: report timeouts in ide_busy_sleep()
Bartlomiej Zolnierkiewicz [Fri, 22 May 2009 14:23:38 +0000 (16:23 +0200)]
ide: report timeouts in ide_busy_sleep()

* change 'hwif' argument to 'drive'
* report an error on timeout

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
15 years agoide: improve failed opcode reporting
Bartlomiej Zolnierkiewicz [Fri, 22 May 2009 14:23:38 +0000 (16:23 +0200)]
ide: improve failed opcode reporting

Nowadays we (almost) always store the currently executing command
in hwif->cmd so we can use it for the failed opcode reporting.

Cc: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
15 years agoide: fix printk() levels in ide_dump_ata[pi]_error()
Bartlomiej Zolnierkiewicz [Fri, 22 May 2009 14:23:37 +0000 (16:23 +0200)]
ide: fix printk() levels in ide_dump_ata[pi]_error()

Fixes "<3>" in error messages like this one:

hdc: cdrom_decode_status: error=0x40 <3>{ LastFailedSense=0x04 }

Reported-by: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
15 years agoide: fix OOPS during ide-cd error recovery
Bartlomiej Zolnierkiewicz [Fri, 22 May 2009 14:23:37 +0000 (16:23 +0200)]
ide: fix OOPS during ide-cd error recovery

On Tuesday 19 May 2009 20:29:28 Martin Lottermoser wrote:

>   hdc: cdrom_decode_status: error=0x40 <3>{ LastFailedSense=0x04 }
>   ide: failed opcode was: unknown
>   hdc: DMA disabled
>   ------------[ cut here ]------------
>   kernel BUG at drivers/ide/ide-io.c:872!

It is possible for ide-cd to ignore ide_error()'s return value under
some circumstances.  Workaround it in ide_intr() and ide_timer_expiry()
by checking if there is a device/port reset pending currently.

Fixes bug #13345:

http://bugzilla.kernel.org/show_bug.cgi?id=13345

Reported-by: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Reported-and-tested-by: Modestas Vainius <modestas@vainius.eu>
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
15 years agoide: fix 40-wire cable detection for TSST SH-S202* ATAPI devices (v2)
Bartlomiej Zolnierkiewicz [Fri, 22 May 2009 14:23:36 +0000 (16:23 +0200)]
ide: fix 40-wire cable detection for TSST SH-S202* ATAPI devices (v2)

Since 2.6.26 we support UDMA66 on ATAPI devices requiring IVB quirk:

  commit 8588a2b732928b343233af9b1855705b8286bed4
  ("ide: add SH-S202J to ivb_list[]")

We also later added support for more such devices in:

  commit e97564f362a93f8c248246c19828895950341252
  ("ide: More TSST drives with broken cable detection")

and in:

  commit 3ced5c49bd2d1f2c7f769e3a54385883de63a652
  ("ide: add TSSTcorp CDDVDW SH-S202H to ivb_list[]")

It turns out that such devices lack cable detection altogether
(which in turn results in incorrect detection of 40-wire cables
by our current cable detection strategy) so always handle them
by trusting host-side cable detection only.

v2:
Model detection fixup from Martin.

Reported-and-tested-by: Martin Lottermoser <Martin.Lottermoser@t-online.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
15 years agoMIPS: IP32: Remove unnecessary if not even harmful volatile keywords.
Ralf Baechle [Fri, 22 May 2009 09:58:43 +0000 (10:58 +0100)]
MIPS: IP32: Remove unnecessary if not even harmful volatile keywords.

They are unneeded and as the issue fixed in lmo commit
63f7ec59053e3f850ab67a9938e631bcba64c6ce shows even harmful.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
15 years agoMIPS: IP32: Fix build error due to uninitialized variable.
Ralf Baechle [Fri, 22 May 2009 09:48:17 +0000 (10:48 +0100)]
MIPS: IP32: Fix build error due to uninitialized variable.

  CC      arch/mips/sgi-ip32/ip32-reset.o
cc1: warnings being treated as errors
arch/mips/sgi-ip32/ip32-reset.c: In function 'debounce':
arch/mips/sgi-ip32/ip32-reset.c:97: error: 'reg_a' is used uninitialized in this function

The issues is old but due to the volatile keyword gcc older than 4.4 did
not warn about this obvious bug.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
15 years agoMIPS: Fix sparse warning in incompatiable argument type of clear_user.
Wu Zhangjin [Wed, 20 May 2009 21:50:01 +0000 (05:50 +0800)]
MIPS: Fix sparse warning in incompatiable argument type of clear_user.

The type of the second argument of access_ok should be (void __user *).
The unnecessary conversion of the clear_user address argument was causing
sparse to emit warnings on the __chk_user_ptr check.

Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
15 years agonilfs2: fix memory leak in nilfs_ioctl_clean_segments
Ryusuke Konishi [Fri, 22 May 2009 11:36:21 +0000 (20:36 +0900)]
nilfs2: fix memory leak in nilfs_ioctl_clean_segments

This fixes a new memory leak problem in garbage collection.  The
problem was brought by the bugfix patch ("nilfs2: fix lock order
reversal in nilfs_clean_segments ioctl").

Thanks to Kentaro Suzuki for finding this problem.

Reported-by: Kentaro Suzuki <k_suzuki@ms.sylc.co.jp>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
15 years agoMerge branch 'fix/hda' into for-linus
Takashi Iwai [Fri, 22 May 2009 06:23:39 +0000 (08:23 +0200)]
Merge branch 'fix/hda' into for-linus

* fix/hda:
  ALSA: hda - fix audio on HP TX25xx series notebooks

15 years agoALSA: hda - fix audio on HP TX25xx series notebooks
Adam Williamson [Thu, 21 May 2009 22:32:59 +0000 (18:32 -0400)]
ALSA: hda - fix audio on HP TX25xx series notebooks

Fixes https://bugtrack.alsa-project.org/alsa-bug/view.php?id=4121

Taken from https://bugzilla.redhat.com/show_bug.cgi?id=498060

Signed-off-by: Adam Williamson <awilliam@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
15 years agopowerpc/maple: Add a quirk to disable MSI for IPR on Bimini
Michael Ellerman [Thu, 21 May 2009 19:10:23 +0000 (19:10 +0000)]
powerpc/maple: Add a quirk to disable MSI for IPR on Bimini

Something in the HW or FW setup is busted and MSIs aren't working with
IPR on Bimini, so until we figure out exaxtly what's up, we quirk them
out

Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
15 years agovideo: stop sh_mobile_lcdcfb only if started
Magnus Damm [Wed, 20 May 2009 14:34:43 +0000 (14:34 +0000)]
video: stop sh_mobile_lcdcfb only if started

This patch fixes the LCDC driver to avoid calling the
function sh_mobile_lcdc_start_stop(priv, 0) unless the
same function has been called before to start the LCDC
hardware.

Triggered when sh_mobile_lcdcfb.c failed to probe() due to
missing MSTP clocks.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
15 years agosh: ap325 camera without i2c driver fix
Magnus Damm [Wed, 20 May 2009 14:30:06 +0000 (14:30 +0000)]
sh: ap325 camera without i2c driver fix

This patch fixes the ap325rxa ncm03j camera code to handle
the case where no i2c driver is present. Without this fix
i2c_transfer() may be passed NULL as adapter which results
in a crash.

Triggered when i2c-sh_mobile.c failed to probe() due to
missing MSTP clocks.

Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
15 years ago[CIFS] fix posix open regression
Steve French [Thu, 21 May 2009 22:21:53 +0000 (22:21 +0000)]
[CIFS] fix posix open regression

Posix open code was not properly adding the file to the
list of open files.  Fix  allocating cifsFileInfo
more than once, and adding twice to flist and tlist.
Also fix mode setting to be done in one place in these
paths.

Signed-off-by: Steve French <sfrench@us.ibm.com>
Reviewed-by: Shirish Pargaonkar <shirishp@us.ibm.com>
Tested-by: Jeff Layton <jlayton@redhat.com>
Tested-by: Luca Tettamanti <kronos.it@gmail.com>
15 years agohugh: update email address
Hugh Dickins [Thu, 21 May 2009 19:33:58 +0000 (20:33 +0100)]
hugh: update email address

My old address will shut down in a few days time: remove it from the tree,
and add a tmpfs (shmem filesystem) maintainer entry with the new address.

Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes...
Linus Torvalds [Wed, 20 May 2009 23:44:37 +0000 (16:44 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jbarnes/pci-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  PCI PM: Fix initialization and kexec breakage for some devices

15 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes...
Linus Torvalds [Wed, 20 May 2009 23:40:24 +0000 (16:40 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jbarnes/drm-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/drm-2.6:
  drm: Copy back ioctl data to userspace regardless of return code.
  drm: Round size of SHM maps to PAGE_SIZE

15 years agoMerge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
Linus Torvalds [Wed, 20 May 2009 23:32:19 +0000 (16:32 -0700)]
Merge branch 'upstream' of git://ftp.linux-mips.org/upstream-linus

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  MIPS: 64-bit: Fix system lockup.
  MIPS: IP28: Change to build with -mr10k-cache-barrier=store
  MIPS: IP22: Fix hang in power button interrupt handler
  MIPS: IP32: Fix hang on shutdown in power button interrupt handler.

15 years agoMerge master.kernel.org:/home/rmk/linux-2.6-arm
Linus Torvalds [Wed, 20 May 2009 23:30:36 +0000 (16:30 -0700)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm

* master.kernel.org:/home/rmk/linux-2.6-arm: (25 commits)
  [ARM] 5519/1: amba probe: pass "struct amba_id *" instead of void *
  [ARM] 5517/1: integrator: don't put clock lookups in __initdata
  [ARM] 5518/1: versatile: don't put clock lookups in __initdata
  [ARM] mach-l7200: fix spelling of SYS_CLOCK_OFF
  [ARM] Double check memmap is actually valid with a memmap has unexpected holes V2
  [ARM] realview: fix broadcast tick support
  [ARM] realview: remove useless smp_cross_call_done()
  [ARM] smp: fix cpumask usage in ARM SMP code
  [ARM] 5513/1: Eurotech VIPER SBC: fix compilation error
  [ARM] 5509/1: ep93xx: clkdev enable UARTS
  ARM: OMAP2/3: Change omapfb to use clkdev for dispc and rfbi, v2
  ARM: OMAP3: Fix HW SAVEANDRESTORE shift define
  ARM: OMAP3: Fix number of GPIO lines for 34xx
  [ARM] S3C: Do not set clk->owner field if unset
  [ARM] S3C2410: mach-bast.c registering i2c data too early
  [ARM] S3C24XX: Fix unused code warning in arch/arm/plat-s3c24xx/dma.c
  [ARM] S3C64XX: fix GPIO debug
  [ARM] S3C64XX: GPIO include cleanup
  [ARM] nwfpe: fix 'floatx80_is_nan' sparse warning
  [ARM] nwfpe: Add decleration for ExtendedCPDO
  ...

15 years ago[ARM] 5519/1: amba probe: pass "struct amba_id *" instead of void *
Alessandro Rubini [Wed, 20 May 2009 21:39:08 +0000 (22:39 +0100)]
[ARM] 5519/1: amba probe: pass "struct amba_id *" instead of void *

The second argument of the probe method points to the amba_id
structure, so it's better passed with the correct type. None of the
current in-tree drivers uses the pointer, so they have only been
checked for a clean compile.

Change suggested by Russell King.

Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
15 years agodrm: Copy back ioctl data to userspace regardless of return code.
Michel Dänzer [Wed, 20 May 2009 11:32:00 +0000 (13:32 +0200)]
drm: Copy back ioctl data to userspace regardless of return code.

Fixes a regression from commit 9d5b3ffc42f7820e8ee07705496955e4c2c38dd9
('drm: fixup some of the ioctl function exit paths'): The vblank ioctl
needs to update the userspace parameters when interrupted by a signal,
which was prevented by the return code check. This could cause the X
server to hang in drmWaitVBlank().

Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
15 years agoMIPS: 64-bit: Fix system lockup.
Greg Ungerer [Wed, 20 May 2009 06:12:32 +0000 (16:12 +1000)]
MIPS: 64-bit: Fix system lockup.

The address range size calculation inside local_flush_tlb_kernel_range()
is being truncated by a too small size variable holder on 64-bit systems.
The truncated size can result in an erroneous tlbsize check that means we
sit spinning inside a loop trying to flush a hige number of TLB entries.
This is for all intents and purposes a system hang. Fix by using an
appropriately sized valiable to hold the size.

[Ralf: Greg's original patch submission identified the issue and fixed one
instance in tlb-r4k.c but there there were several more.  For consistency
I also modified tlb-r3k.c even though that file is only used on 32-bit.]

Signed-off-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
15 years agoMIPS: IP28: Change to build with -mr10k-cache-barrier=store
peter fuerst [Sun, 17 May 2009 21:49:45 +0000 (23:49 +0200)]
MIPS: IP28: Change to build with -mr10k-cache-barrier=store

Richard Sandiford's new code for inserting the cache-barriers, for GCC
4.3 and above and already incorporated in the current GCC-release, uses
a slightly different option-syntax.

Signed-off-by: peter fuerst <post@pfrst.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
15 years agoMIPS: IP22: Fix hang in power button interrupt handler
Ralf Baechle [Sat, 16 May 2009 11:23:45 +0000 (12:23 +0100)]
MIPS: IP22: Fix hang in power button interrupt handler

The hang was caused by the use of disable_irq() from the interrupt handler
itself.  Fixed by the use of disable_irq_nosync().  The issue was
triggered by:

    commit 3aa551c9b4c40018f0e261a178e3d25478dc04a9
    Author: Thomas Gleixner <tglx@linutronix.de>
    Date:   Mon Mar 23 18:28:15 2009 +0100

        genirq: add threaded interrupt handler support

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
15 years agoMIPS: IP32: Fix hang on shutdown in power button interrupt handler.
Andrew Randrianasulu [Thu, 14 May 2009 18:29:27 +0000 (11:29 -0700)]
MIPS: IP32: Fix hang on shutdown in power button interrupt handler.

The hang was caused by the use of disable_irq() from the interrupt handler
itself.  Fixed by the use of disable_irq_nosync().  The issue was
triggered by:

    commit 3aa551c9b4c40018f0e261a178e3d25478dc04a9
    Author: Thomas Gleixner <tglx@linutronix.de>
    Date:   Mon Mar 23 18:28:15 2009 +0100

        genirq: add threaded interrupt handler support

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
15 years agoMerge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
Linus Torvalds [Wed, 20 May 2009 15:56:10 +0000 (08:56 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  cdrom: beyond ARRAY_SIZE of viocd_diskinfo
  xen/blkfront: fix warning when deleting gendisk on unplug/shutdown
  xen/blkfront: allow xenbus state transition to Closing->Closed  when not Connected

15 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6
Linus Torvalds [Wed, 20 May 2009 15:36:53 +0000 (08:36 -0700)]
Merge git://git./linux/kernel/git/sfrench/cifs-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  cifs: fix pointer initialization and checks in cifs_follow_symlink (try #4)

15 years agoALSA: pcsp - fix printk format warning again
Takashi Iwai [Wed, 20 May 2009 15:05:52 +0000 (17:05 +0200)]
ALSA: pcsp - fix printk format warning again

The commit 5a641bcd6398841cc4606b0a732d41a09256fd94 changed the
printk format to '%lu', but the value passed seems to be dependent
on the architecture.  On x86-64, I got a new warning now because an
int value is passed actaully.

As a workaround, just cast the value always to unsigned long.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
15 years agocdrom: beyond ARRAY_SIZE of viocd_diskinfo
Roel Kluin [Wed, 20 May 2009 06:42:06 +0000 (08:42 +0200)]
cdrom: beyond ARRAY_SIZE of viocd_diskinfo

Do not go beyond ARRAY_SIZE of viocd_diskinfo

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
15 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Linus Torvalds [Wed, 20 May 2009 01:44:09 +0000 (18:44 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/sameo/mfd-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
  mfd: pcf50633: fix unsafe disable_irq()
  mfd: Keep a cache of WM8350 volatile values

15 years agoMerge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
Linus Torvalds [Wed, 20 May 2009 01:43:50 +0000 (18:43 -0700)]
Merge git://git./linux/kernel/git/davem/net-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  ipv4: make default for INET_LRO consistent with help text
  net: fix skb_seq_read returning wrong offset/length for page frag data
  pkt_sched: gen_estimator: use 64 bit intermediate counters for bps
  be2net: add two new pci device ids to pci device table
  sch_teql: should not dereference skb after ndo_start_xmit()
  tcp: fix MSG_PEEK race check
  Doc: fixed descriptions on /proc/sys/net/core/* and /proc/sys/net/unix/*
  Neterion: *FIFO1_DMA_ERR set twice, should 2nd be *FIFO2_DMA_ERR?
  mv643xx_eth: fix PPC DMA breakage
  bonding: fix link down handling in 802.3ad mode
  bridge: fix initial packet flood if !STP
  bridge: relay bridge multicast pkgs if !STP
  NET: Meth: Fix unsafe mix of irq and non-irq spinlocks.
  mlx4_en: Fix not deleted napi structures
  ipconfig: handle case of delayed DHCP server
  netpoll: don't dereference NULL dev from np
  wimax/i2400m: fix device crash: fix optimization in _roq_queue_update_ws

15 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris...
Linus Torvalds [Wed, 20 May 2009 01:43:21 +0000 (18:43 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  TPM: get_event_name stack corruption

15 years agoMerge branch 'core/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux...
Linus Torvalds [Wed, 20 May 2009 01:42:45 +0000 (18:42 -0700)]
Merge branch 'core/urgent' of git://git./linux/kernel/git/tip/linux-2.6-tip

* 'core/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  futex: setup writeable mapping for futex ops which modify user space data

15 years agodrm: Round size of SHM maps to PAGE_SIZE
Benjamin Herrenschmidt [Mon, 18 May 2009 01:56:16 +0000 (11:56 +1000)]
drm: Round size of SHM maps to PAGE_SIZE

Currently, userspace can fail to obtain the SAREA mapping (among other
reasons) if it passes SAREA_MAX to drmAddMap without aligning it to the
page size. This breaks for example on PowerPC with 64K pages and radeon
despite the kernel radeon actually doing the right rouding in the first
place.

The way SAREA_MAX is defined with a bunch of ifdef's and duplicated
between libdrm and the X server is gross, ultimately it should be
retrieved by userspace from the kernel, but in the meantime, we have
plenty of existing userspace built with bad values that need to work.

This patch works around broken userspace by rounding the requested size
in drm_addmap_core() of any SHM map to the page size. Since the backing
memory for SHM maps is also allocated within addmap_core, there is no
danger of adjacent memory being exposed due to the increased map size.
The only side effect is that drivers that previously tried to create or
access SHM maps using a size < PAGE_SIZE and failed (getting -EINVAL),
will now succeed at the cost of a little bit more memory used if that
happens to be when the map is created.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
15 years agoTPM: get_event_name stack corruption
Eric Paris [Wed, 13 May 2009 16:50:40 +0000 (12:50 -0400)]
TPM: get_event_name stack corruption

get_event_name uses sprintf to fill a buffer declared on the stack.  It fills
the buffer 2 bytes at a time.  What the code doesn't take into account is that
sprintf(buf, "%02x", data) actually writes 3 bytes.  2 bytes for the data and
then it nul terminates the string.  Since we declare buf to be 40 characters
long and then we write 40 bytes of data into buf sprintf is going to write 41
characters.  The fix is to leave room in buf for the nul terminator.

Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
15 years agoPCI PM: Fix initialization and kexec breakage for some devices
Rafael J. Wysocki [Sun, 17 May 2009 18:17:06 +0000 (20:17 +0200)]
PCI PM: Fix initialization and kexec breakage for some devices

Recent PCI PM changes introduced a bug that causes some devices to be
mishandled after kexec and during early initialization.  The failure
scenario in the kexec case is the following:

* Assume a PCI device is not power-manageable by the platform and has
  PCI_PM_CTRL_NO_SOFT_RESET set in PMCSR.
* The device is put into D3 before kexec (using the native PCI PM).
* After kexec, pci_setup_device() sets the device's power state to
  PCI_UNKNOWN.
* pci_set_power_state(dev, PCI_D0) is called by the device's driver.
* __pci_start_power_transition(dev, PCI_D0) is called and since the
  device is not power-manageable by the platform, it causes
  pci_update_current_state(dev, PCI_D0) to be called.  As a result
  the device's current_state field is updated to PCI_D3, in
  accordance with the contents of its PCI PM registers.
* pci_raw_set_power_state() is called and it changes the device power
  state to D0.  *However*, it should also call pci_restore_bars() to
  reinitialize the device, but it doesn't, because the device's
  current_state field has been modified earlier.

To prevent this from happening, modify pci_platform_power_transition()
so that it doesn't use pci_update_current_state() to update the
current_state field for devices that aren't power-manageable by the
platform.  Instead, this field should be updated directly for devices
that don't support the native PCI PM.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
15 years agofutex: setup writeable mapping for futex ops which modify user space data
Thomas Gleixner [Mon, 18 May 2009 19:20:10 +0000 (21:20 +0200)]
futex: setup writeable mapping for futex ops which modify user space data

The futex code installs a read only mapping via get_user_pages_fast()
even if the futex op function has to modify user space data. The
eventual fault was fixed up by futex_handle_fault() which walked the
VMA with mmap_sem held.

After the cleanup patches which removed the mmap_sem dependency of the
futex code commit 4dc5b7a36a49eff97050894cf1b3a9a02523717 (futex:
clean up fault logic) removed the private VMA walk logic from the
futex code. This change results in a stale RO mapping which is not
fixed up.

Instead of reintroducing the previous fault logic we set up the
mapping in get_user_pages_fast() read/write for all operations which
modify user space data. Also handle private futexes in the same way
and make the current unconditional access_ok(VERIFY_WRITE) depend on
the futex op.

Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
CC: stable@kernel.org
15 years agoFix scripts/setlocalversion with tagged git commit
Nico Schottelius [Sat, 16 May 2009 12:00:56 +0000 (14:00 +0200)]
Fix scripts/setlocalversion with tagged git commit

Produce correct output for
- tagged commit (v2.6.30-rc6)
- past tagged commit (v2.6.30-rc5-299-g7c7327d)
- no tag

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agomfd: pcf50633: fix unsafe disable_irq()
Nelson Castillo [Tue, 12 May 2009 20:26:47 +0000 (13:26 -0700)]
mfd: pcf50633: fix unsafe disable_irq()

Without this change Openmoko Freerunner (GTA02) bootstrap will deadlock.
As pointed out in other patches this issue is in the wild since the merge
of:

: commit 3aa551c9b4c40018f0e261a178e3d25478dc04a9
: Author: Thomas Gleixner <tglx@linutronix.de>
: Date:   Mon Mar 23 18:28:15 2009 +0100
:
:    genirq: add threaded interrupt handler support
:
:    Add support for threaded interrupt handlers

Signed-off-by: Nelson Castillo <arhuaco@freaks-unidos.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: <balajirrao@openmoko.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
15 years agomfd: Keep a cache of WM8350 volatile values
Mark Brown [Thu, 30 Apr 2009 13:48:36 +0000 (14:48 +0100)]
mfd: Keep a cache of WM8350 volatile values

Due to the way that the WM8350 audio driver handles CODEC_ENA many of
the WM8350 audio registers are marked as volatile when they aren't
actually so. Allow the audio driver to see a cache of these values for
inspection during interrupt context.

To do this we need to stop satisfying any bits from volatile registers
from cache - there's no real benefit from doing so anyway, we did the
read already.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
15 years agoMerge branch 'fixes-for-linus' of git://git.monstr.eu/linux-2.6-microblaze
Linus Torvalds [Tue, 19 May 2009 18:31:56 +0000 (11:31 -0700)]
Merge branch 'fixes-for-linus' of git://git.monstr.eu/linux-2.6-microblaze

* 'fixes-for-linus' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: Fix kind-of-intr checking against number of interrupts
  microblaze: Update Microblaze defconfig

15 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6
Linus Torvalds [Tue, 19 May 2009 18:31:24 +0000 (11:31 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/lrg/voltage-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
  regulator: da903x: add missing __devexit_p()

15 years agoAvoid ICE in get_random_int() with gcc-3.4.5
Linus Torvalds [Tue, 19 May 2009 18:25:35 +0000 (11:25 -0700)]
Avoid ICE in get_random_int() with gcc-3.4.5

Martin Knoblauch reports that trying to build 2.6.30-rc6-git3 with
RHEL4.3 userspace (gcc (GCC) 3.4.5 20051201 (Red Hat 3.4.5-2)) causes an
internal compiler error (ICE):

    drivers/char/random.c: In function `get_random_int':
    drivers/char/random.c:1672: error: unrecognizable insn:
    (insn 202 148 150 0 /scratch/build/linux-2.6.30-rc6-git3/arch/x86/include/asm/tsc.h:23 (set (reg:SI 0 ax [91])
            (subreg:SI (plus:DI (plus:DI (reg:DI 0 ax [88])
                        (subreg:DI (reg:SI 6 bp) 0))
                    (const_int -4 [0xfffffffffffffffc])) 0)) -1 (nil)
        (nil))
    drivers/char/random.c:1672: internal compiler error: in extract_insn, at recog.c:2083

and after some debugging it turns out that it's due to the code trying
to figure out the rough value of the current stack pointer by taking an
address of an uninitialized variable and casting that to an integer.

This is clearly a compiler bug, but it's not worth fighting - while the
current stack kernel pointer might be somewhat hard to predict in user
space, it's also not generally going to change for a lot of the call
chains for a particular process.

So just drop it, and mumble some incoherent curses at the compiler.

Tested-by: Martin Knoblauch <spamtrap@knobisoft.de>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agocifs: fix pointer initialization and checks in cifs_follow_symlink (try #4)
Jeff Layton [Tue, 19 May 2009 13:57:03 +0000 (09:57 -0400)]
cifs: fix pointer initialization and checks in cifs_follow_symlink (try #4)

This is the third respin of the patch posted yesterday to fix the error
handling in cifs_follow_symlink. It also includes a fix for a bogus NULL
pointer check in CIFSSMBQueryUnixSymLink that Jeff Moyer spotted.

It's possible for CIFSSMBQueryUnixSymLink to return without setting
target_path to a valid pointer. If that happens then the current value
to which we're initializing this pointer could cause an oops when it's
kfree'd.

This patch is a little more comprehensive than the last patches. It
reorganizes cifs_follow_link a bit for (hopefully) better readability.
It should also eliminate the uneeded allocation of full_path on servers
without unix extensions (assuming they can get to this point anyway, of
which I'm not convinced).

On a side note, I'm not sure I agree with the logic of enabling this
query even when unix extensions are disabled on the client. It seems
like that should disable this as well. But, changing that is outside the
scope of this fix, so I've left it alone for now.

Reported-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Reviewed-by: Christoph Hellwig <hch@inraded.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
15 years agoxen/blkfront: fix warning when deleting gendisk on unplug/shutdown
Ian Campbell [Tue, 19 May 2009 06:27:42 +0000 (08:27 +0200)]
xen/blkfront: fix warning when deleting gendisk on unplug/shutdown

Currently blkfront gives a warning when hot unplugging due to calling
del_gendisk() with interrupts disabled (due to blkif_io_lock).

WARNING: at kernel/softirq.c:124 local_bh_enable+0x36/0x84()
Modules linked in: xenfs xen_netfront ext3 jbd mbcache xen_blkfront
Pid: 13, comm: xenwatch Not tainted 2.6.29-xs5.5.0.13 #3
Call Trace:
 [<c012611c>] warn_slowpath+0x80/0xb6
 [<c0104cf1>] xen_sched_clock+0x16/0x63
 [<c0104710>] xen_force_evtchn_callback+0xc/0x10
 [<c0104e32>] check_events+0x8/0xe
 [<c0104d9b>] xen_restore_fl_direct_end+0x0/0x1
 [<c0103749>] xen_mc_flush+0x10a/0x13f
 [<c0105bd2>] __switch_to+0x114/0x14e
 [<c011d92b>] dequeue_task+0x62/0x70
 [<c0123b6f>] finish_task_switch+0x2b/0x84
 [<c0299877>] schedule+0x66d/0x6e7
 [<c0104710>] xen_force_evtchn_callback+0xc/0x10
 [<c0104710>] xen_force_evtchn_callback+0xc/0x10
 [<c012a642>] local_bh_enable+0x36/0x84
 [<c022f9a7>] sk_filter+0x57/0x5c
 [<c0233dae>] netlink_broadcast+0x1d5/0x315
 [<c01c6371>] kobject_uevent_env+0x28d/0x331
 [<c01e7ead>] device_del+0x10f/0x120
 [<c01e7ec6>] device_unregister+0x8/0x10
 [<c015f86d>] bdi_unregister+0x2d/0x39
 [<c01bf6f4>] unlink_gendisk+0x23/0x3e
 [<c01ac946>] del_gendisk+0x7b/0xe7
 [<d0828c19>] blkfront_closing+0x28/0x6e [xen_blkfront]
 [<d082900c>] backend_changed+0x3ad/0x41d [xen_blkfront]

We can fix this by calling del_gendisk() later in blkfront_closing, after
releasing blkif_io_lock. Since the queue is stopped during the interrupts
disabled phase I don't think there is any danger of an event occuring between
releasing the blkif_io_lock and deleting the disk.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
15 years agoxen/blkfront: allow xenbus state transition to Closing->Closed when not Connected
Ian Campbell [Tue, 19 May 2009 06:25:48 +0000 (08:25 +0200)]
xen/blkfront: allow xenbus state transition to Closing->Closed  when not Connected

This situation can occur when attempting to attach a block device whose
backend is an empty physical CD-ROM driver. The backend in this case
will go directly from the Initialising state to Closing->Closed.
Previously this would result in a NULL pointer deref on info->gd
(xenbus_dev_fatal does not return as a1a15ac5 seems to expect)

Cc: stable@kernel.org
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
15 years agoipv4: make default for INET_LRO consistent with help text
Frans Pop [Tue, 19 May 2009 04:48:38 +0000 (21:48 -0700)]
ipv4: make default for INET_LRO consistent with help text

Commit e81963b1 ("ipv4: Make INET_LRO a bool instead of tristate.")
changed this config from tristate to bool.  Add default so that it is
consistent with the help text.

Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agonet: fix skb_seq_read returning wrong offset/length for page frag data
Thomas Chenault [Tue, 19 May 2009 04:43:27 +0000 (21:43 -0700)]
net: fix skb_seq_read returning wrong offset/length for page frag data

When called with a consumed value that is less than skb_headlen(skb)
bytes into a page frag, skb_seq_read() incorrectly returns an
offset/length relative to skb->data. Ensure that data which should come
from a page frag does.

Signed-off-by: Thomas Chenault <thomas_chenault@dell.com>
Tested-by: Shyam Iyer <shyam_iyer@dell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agonfs: Fix NFS v4 client handling of MAY_EXEC in nfs_permission.
Frank Filz [Mon, 18 May 2009 21:41:40 +0000 (17:41 -0400)]
nfs: Fix NFS v4 client handling of MAY_EXEC in nfs_permission.

The problem is that permission checking is skipped if atomic open is
possible, but when exec opens a file, it just opens it O_READONLY which
means EXEC permission will not be checked at that time.

This problem is observed by the following sequence (executed as root):

  mount -t nfs4 server:/ /mnt4
  echo "ls" >/mnt4/foo
  chmod 744 /mnt4/foo
  su guest -c "mnt4/foo"

Signed-off-by: Frank Filz <ffilzlnx@us.ibm.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org
Tested-by: Eugene Teo <eugeneteo@kernel.sg>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
15 years agopkt_sched: gen_estimator: use 64 bit intermediate counters for bps
Eric Dumazet [Tue, 19 May 2009 02:26:37 +0000 (19:26 -0700)]
pkt_sched: gen_estimator: use 64 bit intermediate counters for bps

gen_estimator can overflow bps (bytes per second) with Gb links, while
it was designed with a u32 API, with a theorical limit of 34360Mbit
(2^32 bytes)

Using 64 bit intermediate avbps/brate counters can allow us to reach
this theorical limit.

Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agobe2net: add two new pci device ids to pci device table
Ajit Khaparde [Mon, 18 May 2009 22:38:55 +0000 (15:38 -0700)]
be2net: add two new pci device ids to pci device table

Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agosch_teql: should not dereference skb after ndo_start_xmit()
Eric Dumazet [Mon, 18 May 2009 22:12:31 +0000 (15:12 -0700)]
sch_teql: should not dereference skb after ndo_start_xmit()

It is illegal to dereference a skb after a successful ndo_start_xmit()
call. We must store skb length in a local variable instead.

Bug was introduced in 2.6.27 by commit 0abf77e55a2459aa9905be4b226e4729d5b4f0cb
(net_sched: Add accessor function for packet length for qdiscs)

Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
15 years agotcp: fix MSG_PEEK race check
Ilpo Järvinen [Sun, 10 May 2009 20:32:34 +0000 (20:32 +0000)]
tcp: fix MSG_PEEK race check

Commit 518a09ef11 (tcp: Fix recvmsg MSG_PEEK influence of
blocking behavior) lets the loop run longer than the race check
did previously expect, so we need to be more careful with this
check and consider the work we have been doing.

I tried my best to deal with urg hole madness too which happens
here:
if (!sock_flag(sk, SOCK_URGINLINE)) {
++*seq;
...
by using additional offset by one but I certainly have very
little interest in testing that part.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Tested-by: Frans Pop <elendil@planet.nl>
Tested-by: Ian Zimmermann <itz@buug.org>
Signed-off-by: David S. Miller <davem@davemloft.net>