ath9k: fix PA predistortion training frame setup

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: set default values for radar pulse detection

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Modify rt2x00queue_remove_l2pad to make skb->data two-byte alignment

When send out skb data to mac80211, orignal code will cause mac80211
unaligned access, so modify code to make mac80211 can natural access.

Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix header_length in rt2x00lib_txdone

Put the assignment of header_length after pull out extra tx headroom

Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix rt2800 USB TX Path DMA issue

rt2800usb chips need to add 1~3 bytes zero padding after each 802.11 header & payload,
and at the end need to add 4 bytes zero padding whether doing TX bulk aggregation or not,

TXINFO_W0_USB_DMA_TX_PKT_LEN in TXINFO must include 1-3 bytes padding after 802.11 header & payload
but do not include 4 bytes end zero padding.

In rt2800usb_get_tx_data_len do not consider multiple of the USB packet size case, sometimes this will
cause USB DMA problem.

Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Use ioremap for SoC devices instead of KSEG1ADDR.

Make the code a bit more portable to architectures that do not support
KSEG1ADDR.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Tested-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Remove unneccessary internal Kconfig symbols.

CONFIG_RT2800PCI_PCI and CONFIG_RT2800PCI_SOC are strictly not needed
as we can check the dependent symbols directly in the rest of Kconfig
and the code, so clean up the Kconfig namespace a bit.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Remove RT30XX Kconfig variables.

Enabling of RT30xx devices via Kconfig variables was introduced when these
devices weren't properly supported yet.
Now that that they are properly supported and functional, we can remove these
Kconfig variables for RT30xx devices and simply enable them whenever rt2800pci
and/or rt2800usb is enabled.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Clean up Kconfig for RT2800 devices.

General clean up of the Kconfig part for RT28XX devices.
Also remove the indications of non functional support for rt27xx/rt28xx/rt30xx
devices, as this is no longer true. They just work fine.
Finally, remove the experimental indications for rt27xx/rt28xx/rt30xx devices
as that is no longer true. Keep the experimental indications for rt33xx/rt35xx
devices, though.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Add initial support for RT3370/RT3390 devices.

Modified from Eddy's patch by adding the RT3370 USB support as well.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Eddy Tsai <Eddy_Tsai@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Increase REGISTER_BUSY_COUNT

For some hardware the REGISTER_BUSY_COUNT isn't sufficient,
increase the REGISTER_BUSY_COUNT to 100 to catch most
devices which have more problems with accessing the registers.

For normal operating devices nothing would change as they will
exit the loop early anyway.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Use macro for caldata array size

The calibration data variable size is based on the number of
channels available in the ath9k driver.

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: kill elapsed_jiffies

Subtract of jiffies is fine even if one variable overwrap.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: simplify iwlagn_tx_skb

We can simplify length calculation in iwlagn_tx_skb, that function
is enough complex, without fuzz it more than necessary.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: remove unused len_org variable

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: add support for setting the ad-hoc multicast rate

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: add support for setting the ad-hoc multicast rate

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Add function to get probe request template for current AP

Chipsets with hardware based connection monitoring need to autonomically
send directed probe-request frames to the AP (in the event of beacon loss,
for example.)

For the hardware to be able to do this, it requires a template for the frame
to transmit to the AP, filled in with the BSSID and SSID of the AP, but also
the supported rate IE's.

This patch adds a function to mac80211, which allows the hardware driver to
fetch this template after association, so it can be configured to the hardware.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: add a private op for configuring radar pulse detection

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: clean up tx buffer setup

Merge ath_tx_send_normal and ath_tx_send_ht_normal.
Move the paprd state initialization and sequence number assignment
to reduce the number of redundant checks.

This not only simplifies buffer allocation error handling, but also
removes a small inconsistency in the buffer HT flag.
This flag should only be set if the frame is also a QoS data frame.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: remove the tx info padding byte abuse

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: handle tx underrun in the driver instead of rate control

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: remove the unnecessary private xretry tx flag

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Cleanup opmode setting logic.

An earlier review suggested moving the code in a small
method that was only called once inline.  This patch
accomplishes that.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Fix low throughput issue with AR93xx

TX underruns were noticed when RTS/CTS preceded aggregates.
This issue was noticed in ar93xx family of chipsets only.
The workaround involves padding the RTS or CTS length up
to the min packet length of 256 bytes required by the
hardware by adding delimiters to the fist descriptor of
the aggregate.

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix bug in delimiter padding computation

There is a roundng error in delimiter padding computation
which causes severe throughput drop with some of AR9003.

signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Cc:stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Add helper function for interpolation

Also round off interpolated values this would improve power
accuracy by 0.5dB in some cases.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Improve power control accuracy for AR9003

It is done for 5Ghz by adding three temperature slopes.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Enable strong signal detection for AR9003

Attenuation from eeprom is configured into attenuator control
register.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Fix XPABIAS level configuration for AR9003

Improper configuration of 0x16288 and 0x16290 would affect transmission.

Cc:stable@kernel.org
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: add eeprom templates for ar9003 family chipsets

We are currently using the default eeprom default and it doesn't
work properly for all ar9003 family chipsets. So add eeprom
templates for different versisons and select the eeprom table
based on the template version programmed in the eeprom.

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Fix paprd training frame failure.

paprd training frame fails in some rates. Fix the rate mask.

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Initialize 2GHz CTL properly.

The last 2GHz CTL was not being initialized, so power was being
set to 0 instead of 30dbm. Initialize to 30 like other CTLs.

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Add new member into the eeprom structure.

Add eeprom base extension structures which are needed for
AR938x caliberation changes and gain calculation.

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Fix a reset failure on AR9382 (2x2).

AR9382 needs to be configured for the correct chain mask before
running AGC/TxIQ caliberation. Otherwise reset would fail.

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Add support for antenna configuration

Support setting the antenna configuration via cfg/mac80211. At the moment only
allow the simple pre-defined configurations we already have (fixed antenna A/B
or diversity), but more advanced settings are possible to implement.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Add antenna configuration

Allow antenna configuration by calling driver's function for it.

We disallow antenna configuration if the wiphy is already running, mainly to
make life easier for 802.11n drivers which need to recalculate HT capabilites.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: Add nl80211 antenna configuration

Allow setting of TX and RX antennas configuration via nl80211.

The antenna configuration is defined as a bitmap of allowed antennas to use.
This API can be used to mask out antennas which are not attached or should not
be used for other reasons like regulatory concerns or special setups.

Separate bitmaps are used for RX and TX to allow configuring different antennas
for receiving and transmitting. Each bitmap is 32 bit long, each bit
representing one antenna, starting with antenna 1 at the first bit. If an
antenna bit is set, this means the driver is allowed to use this antenna for RX
or TX respectively; if the bit is not set the hardware is not allowed to use
this antenna.

Using bitmaps has the benefit of allowing for a flexible configuration
interface which can support many different configurations and which can be used
for 802.11n as well as non-802.11n devices. Instead of relying on some hardware
specific assumptions, drivers can use this information to know which antennas
are actually attached to the system and derive their capabilities based on
that.

802.11n devices should enable or disable chains, based on which antennas are
present (If all antennas belonging to a particular chain are disabled, the
entire chain should be disabled). HT capabilities (like STBC, TX Beamforming,
Antenna selection) should be calculated based on the available chains after
applying the antenna masks. Should a 802.11n device have diversity antennas
attached to one of their chains, diversity can be enabled or disabled based on
the antenna information.

Non-802.11n drivers can use the antenna masks to select RX and TX antennas and
to enable or disable antenna diversity.

While covering chainmasks for 802.11n and the standard "legacy" modes "fixed
antenna 1", "fixed antenna 2" and "diversity" this API also allows more rare,
but useful configurations as follows:

1) Send on antenna 1, receive on antenna 2 (or vice versa). This can be used to
have a low gain antenna for TX in order to keep within the regulatory
constraints and a high gain antenna for RX in order to receive weaker signals
("speak softly, but listen harder"). This can be useful for building long-shot
outdoor links. Another usage of this setup is having a low-noise pre-amplifier
on antenna 1 and a power amplifier on the other antenna. This way transmit
noise is mostly kept out of the low noise receive channel.
(This would be bitmaps: tx 1 rx 2).

2) Another similar setup is: Use RX diversity on both antennas, but always send
on antenna 1. Again that would allow us to benefit from a higher gain RX
antenna, while staying within the legal limits.
(This would be: tx 0 rx 3).

3) And finally there can be special experimental setups in research and
development even with pre 802.11n hardware where more than 2 antennas are
available. It's good to keep the API simple, yet flexible.

Signed-off-by: Bruno Randolf <br1@einfach.org>
--
v7: Made bitmasks 32 bit wide and rebased to latest wireless-testing.
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/b43legacy/main.c: Use printf extension %pV

Using %pV reduces the number of printk calls and
eliminates any possible message interleaving from
other printk calls.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/b43/main.c: Use printf extension %pV

Using %pV reduces the number of printk calls and
eliminates any possible message interleaving from
other printk calls.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/ath/debug.c: Use printf extension %pV

Using %pV reduces the number of printk calls and
eliminates any possible message interleaving from
other printk calls.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rndis_wlan: workaround poor scanning with BCM4320a

BCM4320a devices seem to sometimes do scanning pretty poorly. This can be
workaround by issuing new scan every second, while not yet connected. By this
new scanning method device catches beacons much faster. Fixes bug #20822.

Reported-by: Luís Picciochi <Pitxyoki@gmail.com>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rndis_wlan: workaround device not returning bss for currently connected AP

BCM4320a devices do not return bss for currently connected AP in bss-list,
althought this is required by NDIS specs. Missing bss leads to warning at
net/wireless/sme.c:__cfg80211_connect_result(), WARN_ON(!bss).

Workaround this by crafting bss manually with information we can read from
device. Workaround is only used when device bss-list does not return current
bss, and so is only used with BCM4320a devices and not newer BCM4320b ones.

Fixes bug #20152.

Reported-by: Luís Picciochi <Pitxyoki@gmail.com>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: support hardware TX fragmentation offload

The lower driver is notified when the fragmentation threshold changes
and upon a reconfig of the interface.

If the driver supports hardware TX fragmentation, don't fragment
packets in the stack.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb: return -ENOMEM on alloc fail (instead of CRC check's result)

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb: workarounds: be verbose about hacking SPROM revision, don't duplicate code

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: use const struct fw pointers throughout

This eliminates compiler warnings by doing things how the
firmware class expects.

Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: make initial firmware load asynchronous

Introduce a firmware loading state machine to manage the process
of loading firmware asynchronously and completing initialization
upon success.  The state machine attempts to load the preferred
firmware image.  If that fails, and if an alternative firmware
image is available, it will attempt to load that one.

Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: add API version checking for AP firmware

The AP firmware specifies an API version in the GET_HW_SPEC
command response.  Currently, the driver only supports AP
firmware for the 8366, and only supports API v1.  In the future,
if higher API version firmwares emerge (possibly for different
chips), different ops can be selected based on the reported API
version.

Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: choose proper firmware image as directed by user

The mwl8k can operate in AP or STA mode, depending on the
firmware image that is loaded.  By default, STA firmware is
loaded.  Allow the user to override this default mode at
module load time.  This saves an unnecessary firmware reload
for users only interested in AP mode.

Also, the firmware image can be swapped to meet the user's
add_interface request.  For example, suppose the STA
firmware is loaded, no STA interface has been added, and the
user adds an AP interface.  In this case, the AP firmware
will be loaded to meet the request.

Based on contributions from Pradeep Nemavat <pnemavat@marvell.com>,
Yogesh Powar <yogeshp@marvell.com>, and
Lennert Buytenhek <buytenh@wantstofly.org>.

Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: factor out firmware loading and hw init code

This is in preparation for supporting different fw images for
different interface types, and for supporting asynchronous
firmware loading.

Based on a patch from Pradeep Nemavat <pnemavat@marvell.com>
and Yogesh Powar <yogeshp@marvell.com>

Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: rf_tx_power cmd not supported by AP firmware APIv1

APIv1 AP firmware does not support the RF_TX_POWER command.  It
supports the similar TX_POWER command.

Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: revert unnecessary modification of tx descriptor

This reverts change 783391c443728febc669e40597193308460e7b4f.
The stabilized AP v1 firmware uses the same tx descriptor as
the STA firmware.

Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: EHS_REMOVE_WAKEUP is not always supported

Certain firmware versions, particularly the 8388 found on the XO-1,
do not support the EHS_REMOVE_WAKEUP command that is used to disable
WOL. Sending this command to the card will return a failure that
would get propagated up the stack and cause suspend to fail.

Instead, fall back to an all-zero wakeup mask.

This fixes http://dev.laptop.org/ticket/9967

Signed-off-by: Deepak Saxena <dsaxena@laptop.org>
Signed-off-by: Daniel Drake <dsd@laptop.org>
[includes fixups by Paul Fox]
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: don't block usb8388 suspend if no wakeup conditions are set

This hunk added by commit 66fceb69b72f seems erroneous. We don't want to
prevent suspend of the whole system if no wakeup params are set.

In the case of the usb8388 we do want to keep the card powered up even
if there are no wakeup params. This is because it will continue acting
as a mesh node.

If the mesh is disabled, it would indeed make more sense to power down
the card during suspend, as the equivalent hunk does for the SD interface.
But that's a separate task; for now just restore the previous behaviour.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

carl9170: use generic sign_extend32

This patch replaces the handcrafted
sign extension cruft with a generic
bitop function.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bitops: Provide generic sign_extend32 function

This patch moves code out from wireless drivers where two different
functions are defined in three code locations for the same purpose and
provides a common function to sign extend a 32-bit value.

Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251: use wl12xx_platform_data to pass data

Make use the newly added method to pass platform data for wl1251 too.
This allows to eliminate some redundant code.

Cc: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251: add runtime PM support for SDIO

Add runtime PM support, similar to how it's done for wl1271.
This allows to power down the card when the driver is loaded but
network is not in use.

Cc: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl1251: add power callback to wl1251_if_operations

Call interface specific power callback before calling board specific
one. Also allow that callback to fail. This is how it's done for
wl1271 and will be used for runtime_pm support.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: enable shadow register

For 6000 series devices and up, enable automatic update MAC's register
for better power usage in PSP mode

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: disable disconnected antenna for advanced bt coex

Disconnected antenna algorithm is used to find out which antennas are
disconnected. It should be disabled for devices that support advanced
bluetooth coexist.

Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: seperate disconnected antenna function

Disconnected antenna algorithm is seperated into its own function from chain noise
calibration routine for better code management.

Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: fix RXON HT

When the HT information is changed due to
BSS changes (like legacy stations joining)
we need to recalculate HT RXON parameters.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: re-enable calibration

During the RXON rewrite, this code got lost.
When we've just associated, we need to enable
all calibrations and see if some were already
finished. Add back the missing code.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: fix RXON issues

The RXON rework resulted in a massive loss of
throughput because we weren't programming the
device completely correctly -- the BSSID has
to be programmed into the device before the
AP station is uploaded. To fix this, simply
always send the unassoc RXON, i.e. even when
it was already unassoc so that the BSSID and
some other parameters are updated properly.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: fix needed chains calculation

Garen noticed that this was wrong. Fix
the calibration -- default to multiple
chains and fall back to single where
possible.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: resending QoS command when HT changes

"mac80211: Fix WMM driver queue configuration"
inadvertedly broke iwlwifi, because now mac80211
configures the QoS settings before assoc, and
therefore before HT. Thus, iwlwifi no longer told
the device about the HT setting, which it needs
to -- and thus throughput went down a lot. Fix
this by resending the QoS command to the device
not only when QoS/WMM settings change, but also
when HT changes.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwlifi: update rx write pointer w/o request mac access in the CAM mode

In iwl_rx_queue_update_write_ptr function
replace iwl_write_direct32 with iwl_write32 when not in power save mode.
We don't have to go through grab nic access as the NIC is already awake.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: legacy tx_cmd_protection function

Legacy (4965 and 3945) devices has different tx_cmd_protection routine.
Move to iwl-legacy.c

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: put all the isr related function under ops

There were two type of isr supported by iwlwifi devices.
  legacy isr - only used by legacy devices (3945 & 4965)
  ict isr - used by all new generation of iwlwifi devices

Move all the isr related functions into ops, the ict type of isr
supports only needed for newer devices.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: Legacy isr only used by legacy devices

Move iwl_isr_legacy function to iwl_legacy.c since it only used
by legacy devices.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: fix non-5000+ build

When building 4965 without 5000+ there were a
lot of build errors due to functions being used
that weren't even compiled in. To fix this move
some code around and only compile the HCMD code
for 5000+ series as it's not used for 4965.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: update PCI ID for 100 series devices

Update the supported PCI ID list for 100 series devices

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: update PCI ID for 6000g2a series devices

Update the supported PCI ID list for 6000g2a series devices

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: update PCI ID for 6000g2b series devices

Update the supported PCI ID list for 6000g2b series devices

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Print stats as unsigned ints.

The debugfs code for ath5k was printing some unsigned int
stats with %d instead of %u.  This meant that you could see
negative numbers instead of a clean wrap.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Add watchdog functions for HW queue

Add watchdog functions for managing the Queues inside the hardware.
Normally the driver doesn't have much to do with these queues
directly, but the Ralink drivers did implement watchdog functions
for these. These watchdog functions are not triggered that often,
compared to the other watchdog functions, but I have at least
seen them trigger once or twice during a long stresstest run.

v2: Add extra documentation for register fields

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Remove rt2x00lib_toggle_rx

As part of the queue refactoring, the rt2x00lib_toggle_rx
can be removed and replaced with the call directly to
the set_device_state callback function.

We can remove the STATE_RADIO_RX_ON_LINK and
STATE_RADIO_RX_OFF_LINK, as it was only used for
special behavior inside rt2x00lib rather then the
drivers.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix rt2x00queue_kick_tx_queue arguments

The queue_entry argument to rt2x00queue_kick_tx_queue,
doesn't make sense due to the function name (it is called
kick QUEUE)... But neither do we need the queue_entry, since
we need the data_queue.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Rename queue->lock to queue->index_lock

The queue->lock is only used to protect the index
numbers. Rename the lock accordingly.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: checkpatch.pl error fixes for rt73usb.c

rt73usb.c:43: ERROR: do not initialise statics to 0 or NULL

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: checkpatch.pl error fixes for rt2x00queue.c

rt2x00queue.c:804: ERROR: space prohibited after that open parenthesis '('
rt2x00queue.c:805: ERROR: space prohibited before that close parenthesis ')'

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: checkpatch.pl error fixes for rt2x00link.c

rt2x00link.c:70: ERROR: space prohibited before that close parenthesis ')'

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: checkpatch.pl error fixes for rt2x00lib.h

rt2x00lib.h:60: ERROR: space prohibited after that open parenthesis '('
rt2x00lib.h:60: ERROR: space prohibited before that close parenthesis ')'

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: checkpatch.pl error fixes for rt2x00dev.c

rt2x00dev.c:689: ERROR: spaces required around that '=' (ctx:WxV)

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: checkpatch.pl error fixes for rt2x00config.c

rt2x00config.c:136: ERROR: space required before the open parenthesis '('

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: checkpatch.pl error fixes for rt2800usb.h

rt2800usb.h:43: ERROR: space prohibited after that open parenthesis '('
rt2800usb.h:43: ERROR: space prohibited before that close parenthesis ')'
rt2800usb.h:44: ERROR: space prohibited after that open parenthesis '('
rt2800usb.h:44: ERROR: space prohibited before that close parenthesis ')'

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: checkpatch.pl error fixes for rt2800usb.c

 rt2800usb.c:48: ERROR: do not initialise statics to 0 or NULL

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: checkpatch.pl error fixes for rt2800pci.h

rt2800pci.h:41: ERROR: Macros with complex values should be enclosed in parenthesis
rt2800pci.h:42: ERROR: Macros with complex values should be enclosed in parenthesis
rt2800pci.h:43: ERROR: Macros with complex values should be enclosed in parenthesis
rt2800pci.h:44: ERROR: Macros with complex values should be enclosed in parenthesis
rt2800pci.h:55: ERROR: space prohibited after that open parenthesis '('
rt2800pci.h:55: ERROR: space prohibited before that close parenthesis ')'
rt2800pci.h:56: ERROR: space prohibited after that open parenthesis '('
rt2800pci.h:56: ERROR: space prohibited before that close parenthesis ')'

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: checkpatch.pl error fixes for rt2800lib.c

rt2800lib.c:831: ERROR: inline keyword should sit between storage class and type

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: checkpatch.pl error fixes for rt2800.h

rt2800.h:1511: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1511: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1513: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1513: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1515: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1515: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1517: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1517: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1519: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1519: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1521: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1521: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1661: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1661: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1662: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1662: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1663: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:2013: ERROR: space prohibited after that open parenthesis '('
rt2800.h:2013: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:2014: ERROR: space prohibited after that open parenthesis '('
rt2800.h:2014: ERROR: space prohibited before that close parenthesis ')'

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: checkpatch.pl error fixes for rt2500usb.c

rt2500usb.c:42: ERROR: do not initialise statics to 0 or NULL

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: checkpatch.pl error fixes for rt2500pci.h

rt2500pci.h:1091: ERROR: space prohibited after that open parenthesis '('
rt2500pci.h:1091: ERROR: space prohibited before that close parenthesis ')'
rt2500pci.h:1092: ERROR: space prohibited after that open parenthesis '('
rt2500pci.h:1092: ERROR: space prohibited before that close parenthesis ')'

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: checkpatch.pl error fixes for rt2400pci.h

rt2400pci.h:812: ERROR: space prohibited after that open parenthesis '('
rt2400pci.h:812: ERROR: space prohibited before that close parenthesis ')'
rt2400pci.h:813: ERROR: space prohibited after that open parenthesis '('
rt2400pci.h:813: ERROR: space prohibited before that close parenthesis ')'
rt2400pci.h:950: ERROR: Macros with complex values should be enclosed in parenthesis

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

carl9170: tx path review

This patch fixes a few shortcomings in the tx path.

 * move temp. ampdu_[ack]_len out of txinfo->pad.

 * fix WARN_ON from tx.c:line 300 when tx_ampdu_queue
   fails to queue the frame.

 * In tx_prepare, we already have a local pointer
   to the station's ieee80211_sta struct.

 * remove a second !sta check, tx_prepare already takes
   care of that.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Remove redundant checks for NULL before calls to crypto_free_cipher()

crypto_free_cipher() is a wrapper around crypto_free_tfm() which is a
wrapper around crypto_destroy_tfm() and the latter can handle being passed
a NULL pointer, so checking for NULL in the
ieee80211_aes_key_free()/ieee80211_aes_cmac_key_free() wrappers around
crypto_free_cipher() is pointless and just increase object code size
needlesly and makes us execute extra test/branch instructions that we
don't need.
Btw; don't we have to many wrappers around wrappers ad nauseam here?
Anyway, this patch removes the redundant conditionals.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix comments in rt73usb.h and rt61pci.h

This patch fixes a few comments in rt73usb.h and rt61pci.h.

Signed-off-by: Lalith Suresh <suresh.lalith@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix hw crypto in AP mode for some devices

The BSSID register shouldn't be set in AP mode on some older devices (like
rt73usb) as it breaks hw crypto on these. However, rt2800 devices explicitly
need the BSSID register set to the same value as our own MAC address (only
in AP mode).

Hence, don't set the BSSID from rt2x00lib but move it down into rt2800 to
avoid problems on older devices.

This fixes a regression (at least for rt73usb) and avoids a new regression
for rt2800 devices in 2.6.36.

Reported-by: Johannes Stezenbach <js@sig21.net>
Reported-by: Lee <lee-in-berlin@web.de>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix crash on USB unplug

By not scheduling the TX/RX completion worker threads
when Radio is disabled, or hardware has been unplugged,
the queues cannot be completely cleaned.

This causes crashes when the hardware has been unplugged while
the radio is still enabled.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>