ramips: add support for ELECOM WMC-X1800GST

ELECOM WMC-X1800GST is a 2.4/5 GHz band 11ax (Wi-Fi 6) mesh router,
based on MT7621A

Specification:

- SoC             : MediaTek MT7621A
- RAM             : DDR3 512 MiB (Nanya NT5CC256M16ER-EK)
- Flash           : RAW-NAND 128 MiB (Winbond W29N01HVSINF)
- WLAN            : 2.4/5 GHz 2T2R (MediaTek MT7915D + MT7975D)
- Ethernet        : 3x 10/100/1000 Mbps
  - switch        : MediaTek MT7530 (SoC)
- LEDs/Keys (GPIO): 9x/5x
- UART            : through-hole on PCB ("J4")
  - arrangement   : 3.3V, GND, TX, RX from tri-angle marking
  - settings      : 115200n8
- Power           : 12 VDC, 1 A (Max. 11.5 W)

Flash instruction using initramfs-factory image

1. Boot WMC-X1800GST normally with "Router" mode
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt initramfs-factory image and click apply ("適用")
   button
4. On initramfs image, download sysupgrade image to the device and
   perform sysupgrade with that image
5. Wait ~120 seconds to complete flashing

Notes:

- The "firmware" partition on the stock image is only 0xF00000 (15 MiB)
  and it's too small for the current OpenWrt firmware with UBI format.
  So use the unused area at the end of NAND flash for rootfs (UBI).

MAC addresses:

LAN    : 04:AB:18:xx:xx:BF (Factory, 0x3fff4 (hex))
WAN    : 04:AB:18:xx:xx:C0 (Factory, 0x3fffa (hex))
2.4 GHz: 04:AB:18:xx:xx:C1 (Factory,     0x4 (hex))
5 GHz  : 04:AB:18:xx:xx:C2

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16384
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ath79: qca955x ag71xx upstream driver fix

Fix mdio probe in qca95xx devices and add mandatory clocks to dtsi

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: modules: add irq support for pca953x

Enable interrupt controller support for PCA953x kernel module

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: netdevices: add leds support

Compile LED support to swconfig and phy modules

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: netdevices: add dsa support

Add support for building DSA switch drivers as kernel modules.

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: netdevices: add phy modules

Add support for building multiple phy drivers as kernel modules

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: netdevices: add ag71xx modules

Add support for building both upstream and downstream ag71xx drivers
as modules.

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ath79: rename downstream ag71xx driver

Rename the downstream ag71xx driver to ag71xx-legacy.
It allows both upstream and downstream drivers to be compiled into modules.

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Link: https://github.com/openwrt/openwrt/pull/15926
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ath79: rb91x_nand: use dev_err_probe

Simplifies the error path and avoids having to handle -EPROBE_DEFER
manually.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16416
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

libusb: update to 1.0.27

- Remove unnecessary SourceForge mirror
- Use HTTPS url

Signed-off-by: Yanase Yuki <dev@zpc.st>
Link: https://github.com/openwrt/openwrt/pull/16372
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mbedtls: update to 3.6.1

- This release fixes CVE-2024-45157, CVE-2024-45158, CVE-2024-45159
- Use official release archive instead of git mirror
- Update website url

Signed-off-by: Yanase Yuki <dev@zpc.st>
Link: https://github.com/openwrt/openwrt/pull/16371
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

tcpdump: update to 4.99.5

Changes: https://git.tcpdump.org/tcpdump/blob/4a789712f187e3ac7b2c0044c3a3f8c71b83646e:/CHANGES

Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16402
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

libpcap: update to 1.10.5

Changes: https://git.tcpdump.org/libpcap/blob/bbcbc9174df3298a854daee2b3e666a4b6e5383a:/CHANGES

Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16401
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

rockchip: rework LED configurations for the NanoPi R6C/R6S

This commits fixes the LED on the NanoPi R6 series
after changes in the DTS
https://lore.kernel.org/all/20240612205056.397204-4-seb-dev@mail.de
Reported by Github user: gSpotx2f

Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16275
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

uboot-rockchip: patches: add version when were applied upstream

This patch add a version to uboot patches to help identify in
futures updates when they were upstreamed.

Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16275
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

rockchip: fixes and improve for NanoPi R6 series

Improvement and fixes for the nanopi r6 series, pending on the kernel mailing list
https://lore.kernel.org/all/20240612205056.397204-1-seb-dev@mail.de

Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16275
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

rockchip: add FriendlyElec NanoPi R6C

Hardware Spec
 -SoC: Rockchip RK3588S
       CPU: Quad-core ARM Cortex-A76(up to 2.4GHz) and quad-core Cortex-A55 CPU (up to 1.8GHz)
       GPU: Mali-G610 MP4, compatible with OpenGLES 1.1, 2.0, and 3.2, OpenCL up to 2.2 and Vulkan1.2
       VPU: 8K@60fps H.265 and VP9 decoder, 8K@30fps H.264 decoder, 4K@60fps AV1 decoder, 8K@30fps H.264 and H.265
       NPU: 6TOPs, supports INT4/INT8/INT16/FP16
 -RAM: 64-bit 4GB/8GB LPDDR4X at 2133MHz
 -Flash: 32GB/None eMMC, at HS400 mode
 -Ethernet: one Native Gigabit Ethernet, and one PCIe 2.5G Ethernet
 -USB: one USB 3.0 Type-A and one USB 2.0 Type-A
 -PCIe: one M.2 Key M connector with PCIe 2.1 x1
 -HDMI:
       compatible with HDMI2.1, HDMI2.0, and HDMI1.4 operation
       support up to 7680x4320@60Hz
       Support RGB/YUV(up to 10bit) format
 -microSD: support up to SDR104 mode
 -GPIO:
       30-pin 2.54mm header connector
       up to 1x SPI, 3x UARTs, 3x I2Cs, 2x SPDIFs, 1x I2Ss, 3x PWMs, 20x GPIOs
 -Debug: UART via 3-Pin 2.54mm header, or on-board USB-C to UART
 -LEDs: 4 x GPIO Controlled LED (SYS, WAN, LAN, LED1)
 -others:
        2 Pin 1.27/1.25mm RTC battery input connector for low power RTC IC HYM8563TS
        MASK button for eMMC update
        one user button
 -Power supply: USB-C, support PD, 5V/9V/12V/20V input
 -PCB: 8 Layer, 62x90x1.6mm
 -Ambient Operating Temperature: 0℃ to 70℃

Installation:

Uncompress the OpenWrt sysupgrade and write image to the SD card using dd (dd if=*.img of=/*)

eMMC Installation:

Boot from the SD card
Uncompress the OpenWrt sysupgrade image
fash to eMMC : dd if=*.img of=/dev/mmcblk1
sync
remove SD card
reboot

Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16275
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

uboot-rockchip: add FriendlyElec NanoPi R6C

1- The NanoPi R6C is a SBC by FriendlyElec based on the Rockchip RK3588s.
   It comes with 4GB or 8GB of RAM, a microSD card slot, optional 32GB eMMC
   storage, one M.2 M-Key connector, one RTL8211F 1GbE and one RTL8125
   2.5GbE Ethernet port, one USB 2.0 Type-A and one USB 3.0 Type-A port, a
   HDMI port, a 30-pin GPIO header as well as multiple buttons and LEDs.
2- Renamed 000-backport-upstream-dts-sync.patch -> 000-v2024.10-rc1-backport-upstream-dts-sync.patch
   to add the version when was applied upstream

Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16275
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

tools/meson: update to 1.5.1

Changelog: https://mesonbuild.com/Release-notes-for-1-5-0.html

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Link: https://github.com/openwrt/openwrt/pull/16425
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

6in4: add 'nohostroute' option

Same as 'nohostroute' option for GRE tunnels (commit 0f8b9addfc)
and IPIP tunnels (commit 46ce629fe0)

Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15961
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

6in4: Support fqdn as remote tunnel endpoint

Same as fqdn support in GRE (commit a79f3d11b3) and IPIP (commit 311682905e)

Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15961
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

6in4: allow specifying tunnel device name

Accept 'device' option, allowing to specify custom l3 device name,
instead of default autogenerated one (prefix "6in4-" + interface name)

Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15961
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ls-mc: bump to 10.39.0

Update ls-mc to latest 10.39.0 version.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16360
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ls-dpl: bump to 10.39.0

Update ls-dpl to latest 10.39.0 version.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16360
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ls-rcw: Bump to lf-6.6.23-2.0.0

Bump ls-rcw package to lf-6.6.23-3.0.0.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16360
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

restool: bump to lf-6.6.23-2.0.0

This commit bumps restool layerscape package to lf-6.6.23-2.0.0 version.

Patch was refreshed.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16360
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

uboot-layerscape: bump to lf-6.6.23-2.0.0

This commit bumps u-boot layerscape package to lf-6.6.23-2.0.0 version.

Manually rebased:
0900-layerscape-adjust-LS1021A-IOT-config-for-OpenWrt.patch

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16360
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

tfa-layerscape: Bump to lf-6.6.23-2.0.0

This commit bumps tfa-layerscape package to version lf-6.6.23-2.0.0

Manually rebased:
001-fiptool-hostbuild-fixes.patch

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16360
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

rockchip: backport upstream updates for nanopc t6

Backport ir-receiver/minipcie/poweroff/spi/usb-c support and other
minor fixes for the NanoPC T6 board.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/16443
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

build: remove ac_cv_header_netinet_sctp_h=no from pre-cached variables

We have <netinet/sctp.h> header in lksctp-tools package,
but having this var set to 'no' prevents package's configure
to detect it.

Signed-off-by: Aleksey Vasilenko <aleksey.vasilenko@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16441
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ramips:  TP-Link EC220-G5 v2: swap WLAN leds assignment

Swap incorrect WLAN leds assignment between WLAN 2.4 and 5 GHz for TP-Link EC220-G5 v2

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16331
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mvebu: improve sysupgrade for FortiGate/FortiWiFi devices

Update sysupgrade script (fortinet.sh) for Fortinet devices in
mvebu/cortexa9 and fix the following issues,

- Some individuals of FortiGate/FortiWiFi 30E/5xE devices has wrong
  kernel/rootfs offsets in "firmware-info" partition and they are not
  updated with the current sysupgrade script for Fortinet devices
  (fortinet.sh).
  As a result, the bootloader tries to load kernel data from the wrong
  address and boot with it after OpenWrt installation.
  The new script handles offsets in addition to length values.

and improve the following points.

- Only 2 bytes are handled with the current sysupgrade script
  (fortinet.sh) for kernel/rootfs length. The new script handles 4 bytes
  instead.

- The image names of image0/image1 are not handled and not updated when
  sysupgrade. The new sysupgrade script handles it and update to
  "<dist> <version> <revision>" if firmware metadata is available.
  (ex.: "OpenWrt SNAPSHOT r27440-25384026")

log of new sysupgrade script (fortinet.sh):

Tue Sep 17 10:29:16 UTC 2024 upgrade: Performing system upgrade...
Image Index: 0
Image Name : "OpenWrt SNAPSHOT r27440-25384026"
             --> "OpenWrt SNAPSHOT r27441-b3a0806a05"

  kernel:
    old: 0x003c4e00@0x00200000
    new: 0x003c4e00@0x00200000

  rootfs:
    old: 0x005c0200@0x00800000
    new: 0x005c0200@0x00800000

Unlocking kernel ...

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16409
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mvebu: update triggers of "SPEED" LEDs on FortiGate/FortiWiFi devices

The mdio bus number of mv88e6xxx was changed to '0' from '1' and the
"mv88e6xxx-1:<addr>:<speed>" triggers are unavailable now.
Update triggers for "SPEED" LEDs to make working that LEDs again.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16409
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mvebu: fix "compatible" of regulator for FortiGate/FortiWiFi devices

The driver for fixed voltage regulater uses "regulator-fixed" for
compatible string, not "fixed-regulator".

Fixes: 102dc5a625 ("mvebu: add support for FortiGate 50E")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16409
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ramips: dna_valokuitu-plus-ex400: build sysupgrade.bin

Rename the sysupgrade.tar step to sysupgrade.bin. The sysupgrade.tar is
used in other places and we prefer a sysupgrade.bin instead.

Fixes: fea2264d9fdd ("ramips: mt7621: Add DNA Valokuitu Plus EX400")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ramips: tp-link er605-v2: Remove sysupgrade-tar image

The sysupgrade-tar image build is not defined for this target, do not
add a build instruction for it. The build system will use the definition
from the dna_valokuitu-plus-ex400 board and the build will fail.

This fixes the build of the ramips target.

Fixes: 665c2154ef12 ("ramips: add basic support for tp-link er605-v2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

include: remove kernel 6.1 version file

Remove unused kernel 6.1 version file.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16450
Signed-off-by: Robert Marko <robimarko@gmail.com>

hostapd: fix OWE ssid update on configuration changes

Refresh OWE transition IEs on updating BSS interfaces

Signed-off-by: Felix Fietkau <nbd@nbd.name>

wpa_supplicant: fix num_global_macaddr handling

Pass num_global_macaddr via ubus in the top level config_set call

Signed-off-by: Felix Fietkau <nbd@nbd.name>

hostapd: fix num_global_macaddr and mbssid config handling

Store the config values in the correct field and apply them on restart too

Signed-off-by: Felix Fietkau <nbd@nbd.name>

hostapd: fold extra APuP patches into main patch + src/

Simplifies maintenance

Signed-off-by: Felix Fietkau <nbd@nbd.name>

hostapd: improve ucode bss notifications

Reduce code duplication, add extra callback for bss create

Signed-off-by: Felix Fietkau <nbd@nbd.name>

netifd: update to Git HEAD (2024-09-21)

24f9a93a9559 interface: fix regression on adding hotplug devices to interfaces

Signed-off-by: Felix Fietkau <nbd@nbd.name>

ath79: fix I2C pins on GL-AR750

Change I2C pin flags to GPIO_ACTIVE_HIGH and change SDA to GPIO1.

On my late production GL-AR750 (purchased 2024):
SCL = GPIO16
SDA = GPIO1

Bug report:
I2C bus doesn't work in GL-AR750
https://github.com/openwrt/openwrt/issues/16319

Signed-off-by: Ryan Salsbury <ryanrs@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16406
Signed-off-by: Robert Marko <robimarko@gmail.com>

config: build: make STRIP_KERNEL_EXPORTS depend on BROKEN

STRIP_KERNEL_EXPORTS is currently broken on kernel 6.6 and since this
is the only kernel currently supported, we should rather make it depend
on BROKEN instead of a kernel version until its fixed.

Link: https://github.com/openwrt/openwrt/pull/16440
Signed-off-by: Robert Marko <robimarko@gmail.com>

mac80211: CVE-2024-46760: rtw88: schedule rx work after everything is set up

link: https://lore.kernel.org/all/2024091842-CVE-2024-46760-1eb3@gregkh
Description
===========

In the Linux kernel, the following vulnerability has been resolved:

wifi: rtw88: usb: schedule rx work after everything is set up

Right now it's possible to hit NULL pointer dereference in
rtw_rx_fill_rx_status on hw object and/or its fields because
initialization routine can start getting USB replies before
rtw_dev is fully setup.

The stack trace looks like this:

rtw_rx_fill_rx_status
rtw8821c_query_rx_desc
rtw_usb_rx_handler
...
queue_work
rtw_usb_read_port_complete
...
usb_submit_urb
rtw_usb_rx_resubmit
rtw_usb_init_rx
rtw_usb_probe

So while we do the async stuff rtw_usb_probe continues and calls
rtw_register_hw, which does all kinds of initialization (e.g.
via ieee80211_register_hw) that rtw_rx_fill_rx_status relies on.

Fix this by moving the first usb_submit_urb after everything
is set up.

For me, this bug manifested as:
[    8.893177] rtw_8821cu 1-1:1.2: band wrong, packet dropped
[    8.910904] rtw_8821cu 1-1:1.2: hw->conf.chandef.chan NULL in rtw_rx_fill_rx_status
because I'm using Larry's backport of rtw88 driver with the NULL
checks in rtw_rx_fill_rx_status.

The Linux kernel CVE team has assigned CVE-2024-46760 to this issue.

Affected and fixed versions
===========================

Fixed in 6.6.51 with commit c83d464b82a8
Fixed in 6.10.10 with commit 25eaef533bf3
Fixed in 6.11 with commit adc539784c98

Please see https://www.kernel.org for a full list of currently supported
kernel versions by the kernel community.

Unaffected versions might change over time as fixes are backported to
older supported kernel versions.  The official CVE entry at
https://cve.org/CVERecord/?id=CVE-2024-46760
will be updated if fixes are backported, please check that for the most
up to date information about this issue.

Affected files
==============

The file(s) affected by this issue are:
drivers/net/wireless/realtek/rtw88/usb.c

Mitigation
==========

The Linux kernel CVE team recommends that you update to the latest
stable kernel version for this, and many other bugfixes.  Individual
changes are never tested alone, but rather are part of a larger kernel
release.  Cherry-picking individual commits is not recommended or
supported by the Linux kernel community at all.  If however, updating to
the latest release is impossible, the individual changes to resolve this
issue can be found at these commits:
https://git.kernel.org/stable/c/c83d464b82a8ad62ec9077637f75d73fe955635a
https://git.kernel.org/stable/c/25eaef533bf3ccc6fee5067aac16f41f280e343e
https://git.kernel.org/stable/c/adc539784c98a7cc602cbf557debfc2e7b9be8b3

Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16420
Signed-off-by: Robert Marko <robimarko@gmail.com>

packages: remove remnants of kernels below 6.6

Remove remnants of kernels below 6.6.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16432
Signed-off-by: Robert Marko <robimarko@gmail.com>

ath79: Refresh kernel patches

Make the patches apply cleanly again.

Fixes: 3660ddb8ab6e ("generic: ar8216: remove support for Linux before version 6.1")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mediatek: add Adtran SmartRG SDG-8733A

Specification is similar to other devices of the MT Stuart series:
 * Mediatek MT7988D (3x Cortex-A73, up to 1.8 GHz clock speed)
 * 8 GiB eMMC
 * 2 GiB DDR4 RAM
 * 2500M/1000M/100M LAN port
 * 10000M/5000M/2500M/1000M/100M/10M WAN port
 * MT7992 Tri-band (2.4G, 5G, 6G) 2T2R+3T3R+3T3R 802.11be Wi-Fi
 * Renesas DA14531MOD Bluetooth
 * 2 buttons (Reset, Mesh/WPS)
 * uC-controlled RGB LED via I2C
 * 2x LED for the 2.5G port, 3x LED for the 10G port
 * 3.3V-level 115200 baud UART console via 4-pin Dupont connector
   exposed at the bottom of the device
 * USB-C PD power input

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

generic: phy: aquantia: add pending patch to force MDI pair order

Import pending patch to force MDI pair order.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

bpf-headers: update to version 6.6

Signed-off-by: Felix Fietkau <nbd@nbd.name>

qosify: update to Git HEAD (2024-09-20)

850cc271083d qosify: add support for keeping stats
1501e0935175 bpf_skb_utils.h: add missing include to fix build against newer kernel headers

Signed-off-by: Felix Fietkau <nbd@nbd.name>

generic: remove support for older kernels from swconfig

The legacy swconfig switch driver framework supports kernels older than
Linux 6.6 by using #ifdef'ery with LINUX_VERSION_CODE. Remove all that.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

generic: ar8216: remove support for Linux before version 6.1

Drop support for older kernel versions from legacy AR8216 switch driver.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

generic: drop 6.1 support

Drop config and files for Linux 6.1.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

kirkwood: remove left-over files-6.1 folder

Remove folder with DTS files for Linux 6.1 which has already been
dropped.

Fixes: f142ce87d9 ("kirkwood: remove 6.1 support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

armsr: remove left-over patches for kernel 6.1

Support for Linux 6.1 has already been removed from the armsr target.
Remove left-over patches-6.1 folder as well.

Fixes: fd47fdf527 ("armsr: Remove kernel 6.1 configuration")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

layerscape: remove left-over config-6.1 files

Remove left-over config-6.1 files which should have been removed
when removing kernel 6.1 support.

Fixes: f20987c161 ("layerscape: remove kernel 6.1 support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

pistachio: drop files for Linux 6.1

Drop obsolete config and patches for Linux 6.1.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

ipq40xx: add PoE passthrough GPIO

Add the GPIO pin of the PoE passthrough switch on the Aruba AP-303H.
Power is activated when the pin is low. It enables a PSE chip, so power
is only supplied to downstream devices when they are 802.3af/at
compliant devices.

Ensure you use a sufficient power supply when chaining a consuming
device after the AP.

Signed-off-by: David Bauer <mail@david-bauer.net>

qoriq: drop 6.1 support

Drop config for Linux 6.1.

Link: https://github.com/openwrt/openwrt/pull/16120
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>

qoriq: use kernel 6.6 by default

Switch to Linux kernel version 6.6.

Link: https://github.com/openwrt/openwrt/pull/16120
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>

at91: drop 6.1 support

Drop config and files for Linux 6.1.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>

at91: use kernel 6.6 by default

Switch to Linux kernel version 6.6.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>

tools/llvm-bpf: filter out STAGING_DIR_HOST/include from cflags on non-linux systems

Avoids picking up an incompatible libuuid from util-linux

Signed-off-by: Felix Fietkau <nbd@nbd.name>

generic: 6.6: mtk_eth_soc: increase QDMA RESV_BUF size

Increase QDMA RESV_BUF from 2K to 3K for netsys v2 to match Mediatek SDK.
This helps reduce the possibility of Ethernet transmit timeouts.

Link: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/19d8456c3051e5f6dabf42fa770916a2126ea4bf
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

generic: 6.6: mtk_eth_soc: reset all TX queues on DMA free

The purpose of resetting the TX queue is to reset the
byte and packet count as well as to clear the software
flow control XOFF bit.

MediaTek developers pointed out that netdev_reset_queue would only
resets queue 0 of the network device.
Queues that are not reset may cause unexpected issues.

Packets may stop being sent after reset and "transmit timeout" log may
be displayed.

Import fix from MediaTek's SDK to resolve this issue.

Link: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/5746a94456f466446cc0dcdfbd9078df6df31b63
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

ucode: another fix for host installation

The previous host installation fix accidentally moved the rpath settings
out of CMAKE_HOST_OPTIONS and into CMAKE_OPTIONS.

Fixes: ae42ecaad4e7 ("ucode: fix host installation")
Signed-off-by: Felix Fietkau <nbd@nbd.name>

packages: remove kernel 5.15 remnants

Remove kernel 5.15 remnants.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16417
Signed-off-by: Robert Marko <robimarko@gmail.com>

generic: drop 5.15 support

Drop config and files for Linux 5.15.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16417
Signed-off-by: Robert Marko <robimarko@gmail.com>

realtek: drop 5.15 support

Drop config and files for Linux 5.15.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16417
Signed-off-by: Robert Marko <robimarko@gmail.com>

ramips: add support for netis N6

This commit adds support for netis N6 WiFi 6 router.

Specification
-------------
- SoC       : MediaTek MT7621AT, MIPS, 880 MHz
- RAM       : 256 MiB
- Flash     : NAND 128 MiB (ESMT PSU1GA30DT)
- WLAN      : MT7905DAN + MT7975DN
  - 2.4 GHz : b/g/n/ax, 574 Mbps, MIMO 2x2
  - 5 GHz   : a/n/ac/ax, 1201 Mbps, MIMO 2x2
- Ethernet  : 10/100/1000 Mbps x5 (1x WAN, 4x LAN)
- USB       : 1x 3.0
- UART      : 3.3V, 115200n8
- Buttons   : 1x Reset
              1x WPS
- LEDs      : 1x Power (green)
              1x System (green)
              1x WAN (green)
              1x WiFi 2.4 GHz (green), controlled by phy
              1x WiFi 5 GHz (green), controlled by phy
              1x WPS (green)
              1x USB (green)
              5x ethernet leds (green), controlled by switch
- Power     : 12 VDC, 1.5 A

Installation
------------
1. Update the router using stock firmware web interface and OpenWrt
   factory.bin image.

Recovery and return to stock
----------------------------
1. Assign your PC a static IP 192.168.1.2 and connect to the router using
   the ethernet cable;
2. Power off the router;
3. Press Reset button, power on the router and wait until ethernet led
   start blinking;
4. Release the button;
5. Open http://192.168.1.1/ (N6 System Recovery Mode) in your browser;
6. Upload OpenWrt factory.bin (or stock firmware *.bin) image and proceed
   with upgrade.

MAC addresses
-------------
+---------+-------------------+
|         | MAC example       |
+---------+-------------------+
| LAN     | dc:xx:xx:49:xx:04 |
| WAN     | dc:xx:xx:49:xx:05 |
| WLAN 2g | dc:xx:xx:19:xx:06 |
| WLAN 5g | dc:xx:xx:79:xx:06 |
+---------+-------------------+
The WLAN MAC prototype was found in 'Factory', 0x4
The LAN MAC was found in 'Factory', 0x7ef20
The WAN MAC was found in 'Factory', 0x7ef26

Known issue
-----------
2.4 GHz WLAN doesn't start with mt76 driver.

Probable reason:
   Original Netis N6 EEPROM contains wrong MT_EE_WIFI_CONF value (0xd2).
   Other routers with the same WLAN hardware (e.g., Routerich AX1800)
   have MT_EE_WIFI_CONF = 0x92.

Workaround (already included in this commit):
   Extract EEPROM to a file at the first time boot and change
   MT_EE_WIFI_CONF (offset 0x190) value from 0xd2 to 0x92. See
   /etc/hotplug.d/firmware/11-mt76-caldata for details.

Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16322
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

ramips: fix wrong dts files permissions

This files are executable:
   target/linux/ramips/dts/mt7621_openfi_5pro.dts
   target/linux/ramips/dts/mt7621_winstars_ws-wn536p3.dts
Has to be fixed.

Fixes: 5560791 ("ramips: add support for OpenFi 5Pro Travel Router")
Fixes: 2da2705 ("ramips: add support for WINSTARS WS-WN536P3")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16322
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

tools/expat: update to 2.6.3

This release fixes CVE-2024-45490, CVE-2024-45491 and
CVE-2024-45492.

Changelog:
https://github.com/libexpat/libexpat/blob/R_2_6_3/expat/Changes

Signed-off-by: Yanase Yuki <dev@zpc.st>
Link: https://github.com/openwrt/openwrt/pull/16379
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

kernel: bump 6.6 to 6.6.52

Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.6.52

Removed upstreamed:
backport-6.6/819-v6.8-0010-nvmem-core-add-nvmem_dev_size-helper.patch[1]
backport-6.6/819-v6.8-0011-nvmem-u-boot-env-use-nvmem_add_one_cell-nvmemsubsys.patch[2]
backport-6.6/819-v6.8-0012-nvmem-u-boot-env-use-nvmem-device-helpers.patch[3]
backport-6.6/819-v6.8-0013-nvmem-u-boot-env-improve-coding-style.patch[4]
backport-6.6/822-v6.11-0011-nvmem-u-boot-env-error-if-NVMEM-device-is-too-small.patch[5]

Manually rebased:
starfive/patches-6.6/0048-riscv-dts-starfive-Add-full-support-except-VIN-and-V.patch

All other patches automatically rebased.

1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.52&id=820b1b981aeb8b8e60db2835ddd430c9d1bc6072
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.52&id=ae91c9c7b67d4d47206fe8cbb2ab89687d283dcc
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.52&id=2eea394c31cbc3d853a26ef2ddb8f5bd24d4d002
4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.52&id=368fa77b7945bdbdf0e3bb26b5abcae4fba25a20
5. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.6.52&id=2278629c3ebb1a912fe0a1f19f088312600742a4

Build system: x86/64
Build-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3
Run-tested: x86/64/AMD Cezanne, flogic/xiaomi_redmi-router-ax6000-ubootmod, ramips/tplink_archer-a6-v3

Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16422
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

mediatek: filogic: openwrt_one: let U-Boot set LAN MAC address

Instead of reading it from flash directly, let U-Boot assign the LAN
MAC address. Set label-mac-device while at it and sort aliases in DT
alphabetically.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

uboot-mediatek: openwrt_one: set ethaddr from factory

Set LAN MAC address from factory partition on NOR flash.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

at91: 6.6: add missing kernel symbols

Kconfig symbols CONFIG_VIDEO_MICROCHIP_CSI2DC, CONFIG_VIDEO_MICROCHIP_ISC
and CONFIG_VIDEO_MICROCHIP_XISC are missing for sama5 and sama7 causing
the build to abort or waiting for user input. Add the symbols (disabled)
so build with Linux 6.6 succeeds.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

mediatek: filogic: fix WiFi MAC address retrieval for Adtran SDG-8734

Fix a typo in the MAC address assignment script affecting SDG-8734.

Fixes: c71b68acdd ("mediatek: filogic: add Adtran SmartRG Mount Stuart series")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

dtc: Update to 1.7.1

Update to dtc to 1.7.1. Change tarball to gzip and drop upstreamed patch
010-both-libraries.patch. Disable tests.

Changes sinve v1.7.0 include:
 * dtc
   * Fix check for 10-bit I2C addresses
   * Improve documentation of -@ option
   * Update to libyaml >= 0.2.3
   * Improvements & fixes for device graph checks
   * Add -L / --local-fixups option
   * Add check for length of interrupt-map properties
 * libfdt
   * Add fdt_path_getprop_namelen()
   * Add fdt_get_symbol() and fdt_get_symbol_namelen()
   * Correct documentation of fdt_path_offset()
   * Correct documentation of fdt_appendprop_addrrange()
   * Validate aliases is fdt_get_alias_namelen()
   * Don't overwrite phandles when applying overlays
   * Require Python 3
 * pylibfdt
   * Support boolean properties
   * Fixes for current Python versions
 * General
   * Assorted bugfixes
   * Assorted build improvements
   * Assorted typo fixes in docs
   * Some additional testcases
   * Move to GitHub Actions based CI

Signed-off-by: Andreas Gnau <andreas.gnau@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/16411
Signed-off-by: Robert Marko <robimarko@gmail.com>

kernel: rework Initramfs compile cpio handling

Now that we copy and then delete the Per-Device rootfs linux directory,
it's not valid anymore placing the generated cpio there as artifacts
or subsequent commands need the generated cpio.

To handle this, rework Initramfs compile cpio handling by placing them in
the KERNEL_BUILD_DIR but add to the name the rootfs HASH ID.

To also prevent race condition, generate and access these file under a
lock to prevent fit command to reference a cpio while a parallel
execution is genereting it.

Fixes: 52cc9d82f113 ("kernel: rework Initramfs locking logic")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>

kernel: fix flock name for gen-initramfs lock

Fix flock name for gen-initramfs lock as $(2) starts with .HASH making
the lock name gen-initramfs-.HASH.flock

Fix this to a better name of gen-initramfs.HASH.flock

Fixes: 52cc9d82f113 ("kernel: rework Initramfs locking logic")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>

kernel: fix wrong rework for Initramfs cpio xz compression

Fix wrong rework for Initramfs cpio xz compression where it was wrongly
dropped the Per-Device linux directory if condition.

Fixes: 52cc9d82f113 ("kernel: rework Initramfs locking logic")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>

tools/cmake: update to 3.30.3

Release notes: https://cmake.org/cmake/help/latest/release/3.30.html

Signed-off-by: Yanase Yuki <dev@zpc.st>
Link: https://github.com/openwrt/openwrt/pull/16378
Signed-off-by: Robert Marko <robimarko@gmail.com>

realtek: add support for HPE 1920-48G (JG927A) and 1920-48G-PoE (JG928A)

Hardware information:
---------------------

- SoC: RTL8393M
- Copper phy: 6×RTL8218B
- Fibre phy: RTL8214FC
- Flash: 32MiB SPI NOR, MX25L25635FMI
- RAM: 128MiB DDR3, Micron MT41K64M16TW-107
- Serial port: ±5V serial port to RJ45, ZT3232 (MAX3232 compatible)
- +370W POE on JG928A model

Note: SFP ports currently non-functional due to missing support for
RTL8214FC on the RTL8393M target.

Updated for Linux 6.6 kernel.

Installation:
-------------
- Initial installation follows same process as HPE 1920-24G (JG924A)

- Based on prior work of Jan Hoffmann <jan@3e8.eu>
- Additional work by Andreas Böhler <dev@aboehler.at>
- PoE updates and tidy-up by Stephen Howell <howels@allthatwemight.be>
Signed-off-by: Stephen Howell <howels@allthatwemight.be>

realtek: default to 6.6

Now that there is 6.6 support for realtek, lets encourage testing it by
making it default so 5.15 can be dropped ASAP.

Link: https://github.com/openwrt/openwrt/pull/16408
Signed-off-by: Robert Marko <robimarko@gmail.com>

generic: 6.6: backport pending fix for Aquantia PHY LEDs

The 'active-low' property was not applied correctly and two fixes
are required to make inverted LEDs work as expected.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

rpcd: update to git HEAD

 bcc091d session: Fix crash when the UCI option 'password' or 'username' is missing
 9f4b86e rpcd: iwinfo: add IEEE 802.11be support

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

iwinfo: update to git HEAD

Add support for 802.11be (HE) radios.

 4b7c47c iwinfo: sync with upstream nl80211.h
 268a662 iwinfo: add basic IEEE 802.11be support

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

at91: enable 6.6 testing kernel

The at91 now supports 6.6 kernel as testing.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>

at91: refresh config-6.6

Refresh kernel config for Linux 6.6.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>

at91: 6.6: change dts files location

Change dts files location to subfolder microchip for compatibility with kernel 6.6

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>

at91: 6.6: remove obsolete patches

Remove obsolete patches no longer applicable to the 6.6 kernel.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>

kernel/at91: Restore kernel files for v6.1

This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.

For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>

kernel/at91: Create kernel files for v6.6 (from v6.1)

This is an automatically generated commit.

When doing `git bisect`, consider `git bisect --skip`.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>

at91: remove unnecessary dts files

Remove unnecessary dts files already included in the 6.1 kernel.

Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>

siflower: new target for Siflower SF19A2890

Siflower SF19A2890 is an SoC with:
Dual-core MIPS InterAptiv at 800MHz
DDR3 controller
One Gigabit Ethernet MAC with RGMII and IPv4 HNAT engine
Built-in 2x2 11N + 2x2 11AC WiFi radio
USB 2.0 OTG
I2C/SPI/GPIO and various other peripherals

This PR adds support for SF19A2890 EVB with ethernet support.

EVB spec:
Memory: DDR3 128M
Ethernet: RTL8367RB 5-port gigabit switch
Flash: 16M NOR
Others: MicroUSB OTG, LED x 1, Reset button x1

The built image can be flashed using u-boot recovery.

This target is marked as source-only until support for a commercial
router board comes.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>

package: busybox: disable mips16 on hard-float

The busybox built with mips16 enabled has broken seq command.
Disassembling shows that the call to hard-float strtod in mips16
code is generated without the __call_stub_fp:
```
   0x00406d6f <+118>:   lw      v0,32(sp)
   0x00406d71 <+120>:   sll     s0,2
   0x00406d73 <+122>:   addu    s0,v0,s0
   0x00406d75 <+124>:   lw      a0,-4(s0)
   0x00406d79 <+128>:   jal     0x44ebc1 <strtod@mips16plt>
   0x00406d7d <+132>:   addiu   a1,sp,84
   0x00406d7f <+134>:   sw      v0,64(sp)
   0x00406d81 <+136>:   lw      v0,0(s1)
   0x00406d83 <+138>:   sw      v1,68(sp)
```

As a result, strtod returns the result in float point registers
while the calling mips16 code expect the result in v0/v1.

Disable mips16 on hard-float targets for now. The built .ipk goes
from 213316 bytes to 251419 bytes.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>

ramips: mt7621: use lzma-loader for Sercomm NA502s

This fixes a well-known "LZMA ERROR 1" error on Sercomm NA502s, reported
on the OpneWrt forum [0].

[0] https://forum.openwrt.org/t/206640

Signed-off-by: Andreas Böhler <dev@aboehler.at>

ramips: mtd_eth_soc: use dev_err_probe

Simplifies the code by avoiding having to manually handle -EPROBE_DEFER.

Signed-off-by: Rosen Penev <rosenp@gmail.com>