Ville Syrjälä [Tue, 8 Dec 2015 16:41:54 +0000 (18:41 +0200)]
drm: Add plane->name and use it in debug prints
Show a sensible name for the plane in debug mesages. The driver
may supply its own name, otherwise the core genrates the name
("plane-0", "plane-1" etc.).
v2: kstrdup() the name passed by the caller (Jani)
v3: Generate a default name if the driver doesn't supply one
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449592922-5545-7-git-send-email-ville.syrjala@linux.intel.com
Ville Syrjälä [Tue, 8 Dec 2015 16:41:53 +0000 (18:41 +0200)]
drm: Add crtc->name and use it in debug messages
Show a sensible name for the crtc in debug mesages. The driver may
supply its own name, otherwise the core genrates the name
("crtc-0", "crtc-1" etc.).
v2: kstrdup() the name passed by the caller (Jani)
v3: Generate a default name if the driver doesn't supply one
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449592922-5545-6-git-send-email-ville.syrjala@linux.intel.com
Ville Syrjälä [Tue, 8 Dec 2015 16:41:52 +0000 (18:41 +0200)]
drm: Use driver specified encoder name
Use the encoder name passed by the driver if non-NULL, otherwise fall
back to the old style name.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449592922-5545-5-git-send-email-ville.syrjala@linux.intel.com
Ville Syrjälä [Wed, 9 Dec 2015 14:20:18 +0000 (16:20 +0200)]
drm: Pass 'name' to drm_encoder_init()
Done with coccinelle for the most part. However, it thinks '...' is
part of the semantic patch, so I put an 'int DOTDOTDOT' placeholder
in its place and got rid of it with sed afterwards.
@@
identifier dev, encoder, funcs;
@@
int drm_encoder_init(struct drm_device *dev,
struct drm_encoder *encoder,
const struct drm_encoder_funcs *funcs,
int encoder_type
+ ,const char *name, int DOTDOTDOT
)
{ ... }
@@
identifier dev, encoder, funcs;
@@
int drm_encoder_init(struct drm_device *dev,
struct drm_encoder *encoder,
const struct drm_encoder_funcs *funcs,
int encoder_type
+ ,const char *name, int DOTDOTDOT
);
@@
expression E1, E2, E3, E4;
@@
drm_encoder_init(E1, E2, E3, E4
+ ,NULL
)
v2: Add ', or NULL...' to @name kernel doc (Jani)
Annotate the function with __printf() attribute (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449670818-2966-1-git-send-email-ville.syrjala@linux.intel.com
Ville Syrjälä [Wed, 9 Dec 2015 14:19:55 +0000 (16:19 +0200)]
drm: Pass 'name' to drm_universal_plane_init()
Done with coccinelle for the most part. It choked on
msm/mdp/mdp5/mdp5_plane.c like so:
"BAD:!!!!! enum drm_plane_type type;"
No idea how to deal with that, so I just fixed that up
by hand.
Also it thinks '...' is part of the semantic patch, so I put an
'int DOTDOTDOT' placeholder in its place and got rid of it with
sed afterwards.
I didn't convert drm_plane_init() since passing the varargs through
would mean either cpp macros or va_list, and I figured we don't
care about these legacy functions enough to warrant the extra pain.
@@
typedef uint32_t;
identifier dev, plane, possible_crtcs, funcs, formats, format_count, type;
@@
int drm_universal_plane_init(struct drm_device *dev,
struct drm_plane *plane,
unsigned long possible_crtcs,
const struct drm_plane_funcs *funcs,
const uint32_t *formats,
unsigned int format_count,
enum drm_plane_type type
+ ,const char *name, int DOTDOTDOT
)
{ ... }
@@
identifier dev, plane, possible_crtcs, funcs, formats, format_count, type;
@@
int drm_universal_plane_init(struct drm_device *dev,
struct drm_plane *plane,
unsigned long possible_crtcs,
const struct drm_plane_funcs *funcs,
const uint32_t *formats,
unsigned int format_count,
enum drm_plane_type type
+ ,const char *name, int DOTDOTDOT
);
@@
expression E1, E2, E3, E4, E5, E6, E7;
@@
drm_universal_plane_init(E1, E2, E3, E4, E5, E6, E7
+ ,NULL
)
v2: Split crtc and plane changes apart
Pass NUL for no-name instead of ""
Leave drm_plane_init() alone
v3: Add ', or NULL...' to @name kernel doc (Jani)
Annotate the function with __printf() attribute (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449670795-2853-1-git-send-email-ville.syrjala@linux.intel.com
Ville Syrjälä [Wed, 9 Dec 2015 14:19:31 +0000 (16:19 +0200)]
drm: Pass 'name' to drm_crtc_init_with_planes()
Done with coccinelle for the most part. However, it thinks '...' is
part of the semantic patch, so I put an 'int DOTDOTDOT' placeholder
in its place and got rid of it with sed afterwards.
I didn't convert drm_crtc_init() since passing the varargs through
would mean either cpp macros or va_list, and I figured we don't
care about these legacy functions enough to warrant the extra pain.
@@
identifier dev, crtc, primary, cursor, funcs;
@@
int drm_crtc_init_with_planes(struct drm_device *dev,
struct drm_crtc *crtc,
struct drm_plane *primary, struct drm_plane *cursor,
const struct drm_crtc_funcs *funcs
+ ,const char *name, int DOTDOTDOT
)
{ ... }
@@
identifier dev, crtc, primary, cursor, funcs;
@@
int drm_crtc_init_with_planes(struct drm_device *dev,
struct drm_crtc *crtc,
struct drm_plane *primary, struct drm_plane *cursor,
const struct drm_crtc_funcs *funcs
+ ,const char *name, int DOTDOTDOT
);
@@
expression E1, E2, E3, E4, E5;
@@
drm_crtc_init_with_planes(E1, E2, E3, E4, E5
+ ,NULL
)
v2: Split crtc and plane changes apart
Pass NULL for no-name instead of ""
Leave drm_crtc_init() alone
v3: Add ', or NULL...' to @name kernel doc (Jani)
Annotate the function with __printf() attribute (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449670771-2751-1-git-send-email-ville.syrjala@linux.intel.com
Daniel Vetter [Tue, 8 Dec 2015 08:49:17 +0000 (09:49 +0100)]
drm: Documentation style guide
Every time I type or review docs this seems a bit different. Try to
document the common style so we can try to unify at least new docs.
v2: Spelling fixes from Pierre, Laurent and Jani.
v3: More spelling fixes from Lukas.
Cc: Pierre Moreau <pierre.morrow@free.fr>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lukas Wunner <lukas@wunner.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449564561-3896-1-git-send-email-daniel.vetter@ffwll.ch
Daniel Vetter [Fri, 4 Dec 2015 08:46:08 +0000 (09:46 +0100)]
drm: Document drm_encoder/crtc_helper_funcs
Mostly this is about all the callbacks used for modesets by both legacy
CRTC helpers and atomic helpers and I figured it doesn't make all that
much sense to split this up.
v2: Suggestions from Thierry.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449218769-16577-28-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Thierry Reding <treding@nvidia.com>
Daniel Vetter [Wed, 9 Dec 2015 08:29:36 +0000 (09:29 +0100)]
drm: Move drm_display_mode an related docs into kerneldoc
This was in the documentation for modeset helper hooks, where it is a
bit misplaced.
v2: Reindent the drm_mode_status enum, inspired by Ville.
v3: Suggestions from Ville and Thierry.
v4: Small fixup that 0day spotted.
v5: Slight change to avoid accidental headings in kerneldoc output.
Cc: ville.syrjala@linux.intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449218769-16577-27-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v3)
Reviewed-by: Thierry Reding <treding@nvidia.com> (v3)
Daniel Vetter [Fri, 4 Dec 2015 08:46:06 +0000 (09:46 +0100)]
drm/atomic-helper: Mention the new system/resume helpers the docs
They have pretty kerneldoc already, but better to link to that in
one of the overview sections.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449218769-16577-26-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Thierry Reding <treding@nvidia.com>
Daniel Vetter [Fri, 4 Dec 2015 08:46:05 +0000 (09:46 +0100)]
drm: Document drm_connector_helper_funcs
Nothing special, except the somewhat awkward split in probe helper
callbacks between here and drm_crtc_funcs.
v2: Suggestions from Thierry.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449218769-16577-25-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Thierry Reding <treding@nvidia.com>
Daniel Vetter [Fri, 4 Dec 2015 08:46:04 +0000 (09:46 +0100)]
drm: Document drm_plane_helper_funcs
Plus related hooks used to do atomic plane updates since they only
really make sense as a package.
v2: Suggestions from Thierry.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449218769-16577-24-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Thierry Reding <treding@nvidia.com>
Daniel Vetter [Fri, 4 Dec 2015 08:46:02 +0000 (09:46 +0100)]
drm: Kerneldoc for drm_mode_config_funcs
The meat here is definitely the detailed specs for what atomic_check
and atomic_commit are supposed to do.
And another candidate for a core vfunc that should be in a helper really
(output_poll_changed this time around).
v2: Feedback from Eric on irc:
- spelling fixes.
- spec what async should do
- copy the event related paragraphs from page_flip and adjust
- make it clear that a successful async commit is not allowed to leave
the pipe dead or disabled.
v3: Use FIXME comments to annotate functions that we should move to
some helpers.
v4: Suggestions from Thierry.
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449218769-16577-22-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Thierry Reding <treding@nvidia.com>
Daniel Vetter [Fri, 4 Dec 2015 08:46:01 +0000 (09:46 +0100)]
drm: Add kerneldoc for drm_framebuffer_funcs
While typing these I noticed that ->dirty is a bit a can of worms
and even supports blt/fill semantics ... shocked me a bit.
Oh well it's defined in a way that nothing bad (just a bit of inefficiency)
will happen for drivers which supports this. So I didn't bother copying
the detailed spec into the new kerneldoc.
v2: Suggestions from Thierry.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449218769-16577-21-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Thierry Reding <treding@nvidia.com>
Daniel Vetter [Fri, 4 Dec 2015 08:46:00 +0000 (09:46 +0100)]
drm: document drm_crtc_funcs
And merge any docbook we have into the kerneldoc comments.
Since it's a legacy entry point with only two implementation (one each
in atomic and legacy crtc helpers) I've made the documentation for
set_config fairly sparse - no one should ever need to look at this
again, all the ABI we have is baked into code.
For ->page_flip otoh I kept all the extensive docs from the docbook
and even extended it where it was lacking: Currently we have a pile of
legacy page_flip implemantations, and even for atomic drivers there's
not yet a standard implementation in the helpers. Which means every
driver needs to implement this itself, and precise specs are really
valuable.
Otherwise there's just cursor, which really just boils down to "use at
least universal planes". And gamma tables (where we have a bit a mess
with the fbdev helper gamma hooks).
v2: Spelling fixes (Eric).
v3: Suggestions from Thierry.
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449218769-16577-20-git-send-email-daniel.vetter@ffwll.ch
Daniel Vetter [Fri, 4 Dec 2015 08:45:59 +0000 (09:45 +0100)]
drm: connector->dpms is not optional
We always register the DPMS property, it's really a fundamental
part of a display driver. So don't check whether the vfunc is there,
it's non-optional
Yes I've audited all the almost 100 drm_connector_funcs we have, no
one botched this ;-)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449218769-16577-19-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Thierry Reding <treding@nvidia.com>
Daniel Vetter [Fri, 4 Dec 2015 08:45:58 +0000 (09:45 +0100)]
drm: Document drm_connector_funcs
The special case here is that both ->detect and ->force are actually
functions only called by the probe helpers and hence really shouldn't
be here. But since they've used by pretty much every driver I figured
it's better to just document this for now instead of holding this doc
patch hostage until that's all fixed. For that reason also group force
right next to detect.
v2: Use FIXME comments to annotate where we should move a hook to
helpers.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449218769-16577-18-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Thierry Reding <treding@nvidia.com>
Daniel Vetter [Fri, 4 Dec 2015 08:45:57 +0000 (09:45 +0100)]
drm: Document drm_atomic_*_get_property
Yes these are internal functions and not exported and we generally
don't document them. But for symmetry with the _set_property functions
(which are exported for the atomic helpers) I'd like to document them.
Upcoming vtable kerneldoc will reference both the set and get_property
functions.
v2: Suggestions from Thierry.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449218769-16577-17-git-send-email-daniel.vetter@ffwll.ch
Daniel Vetter [Fri, 4 Dec 2015 16:14:07 +0000 (17:14 +0100)]
drm: Move encoder->save/restore into nouveau
Nouveau is the only user, and atomic drivers should do state
save/restoring differently. So move it into noveau.
Saves me typing some kerneldoc, too ;-)
v2: Move misplaced hunk into earlier nouveau patch.
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449245647-1315-1-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Thierry Reding <treding@nvidia.com>
Daniel Vetter [Fri, 4 Dec 2015 08:45:55 +0000 (09:45 +0100)]
drm: Remove crtc/connector->save/restore hooks
They're not how system suspend/resume should be done with atomic
(there's new helpers for that developed by Thierry Reding), and for
legacy drivers this really should be a helper hook and not a core one.
But there's not even helper code to use them, and only 2 drivers
(which now have their own private hooks) set them. Ditch them.
Saves me typing some kerneldoc, too ;-)
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449218769-16577-15-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Thierry Reding <treding@nvidia.com>
Daniel Vetter [Fri, 4 Dec 2015 16:13:38 +0000 (17:13 +0100)]
drm/nouveau: Use private save/restore hooks for CRTCs
I want to remove the core ones since with atomic drivers system
suspend/resume is solved much differently. And there's only 2 drivers
(gma500 besides nouveau) really using them.
v2: Fixup bugs Ilia spotted.
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449245618-1127-1-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Thierry Reding <treding@nvidia.com>
Daniel Vetter [Fri, 4 Dec 2015 08:45:53 +0000 (09:45 +0100)]
drm/gma500: Move to private save/restore hooks
I want to remove the core ones since with atomic drivers system
suspend/resume is solved much differently. And there's only 2 drivers
(nouveau besides gma500) really using them.
v2: Fixup build noise 0day reported.
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449218769-16577-13-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Thierry Reding <treding@nvidia.com> (v1)
Rodrigo Vivi [Mon, 7 Dec 2015 18:35:06 +0000 (10:35 -0800)]
drm/i2c/tda998x: Remove unused save/restore drm encoder helpers.
save/restore have been removed from drm_encoder_helper_funcs by
'commit
79f13ad5d8e0 ("drm: Move encoder->save/restore into nouveau")'
But this module was still defining it with empty content causing
compilation fails:
drivers/gpu/drm/i2c/tda998x_drv.c:1354:10: warning: initialization from
incompatible pointer type [-Wincompatible-pointer-types]
.save = tda998x_encoder_save,
drivers/gpu/drm/i2c/tda998x_drv.c:1355:2: error: unknown field 'restore'
specified in initializer
.restore = tda998x_encoder_restore,
Cc: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449513306-17309-1-git-send-email-rodrigo.vivi@intel.com
Daniel Vetter [Fri, 4 Dec 2015 08:45:52 +0000 (09:45 +0100)]
drm/vmwgfx: Drop dummy save/restore hooks
These hooks will be gone soon.
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449218769-16577-12-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Thierry Reding <treding@nvidia.com>
Daniel Vetter [Fri, 4 Dec 2015 08:45:51 +0000 (09:45 +0100)]
drm/virtio: Drop dummy save/restore functions
These hooks will be gone soon.
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449218769-16577-11-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Thierry Reding <treding@nvidia.com>
Daniel Vetter [Fri, 4 Dec 2015 08:45:50 +0000 (09:45 +0100)]
drm/qxl: Drop dummy save/restore hooks
These hooks will be gone soon.
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449218769-16577-10-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Thierry Reding <treding@nvidia.com>
Daniel Vetter [Fri, 4 Dec 2015 08:45:49 +0000 (09:45 +0100)]
drm/nouveau: Ditch NULL save/restore hook assignments
gcc does this for us, and these hooks will be gone soon.
Cc: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449218769-16577-9-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Thierry Reding <treding@nvidia.com>
Daniel Vetter [Fri, 4 Dec 2015 08:45:48 +0000 (09:45 +0100)]
drm: Update drm_plane_funcs kerneldoc
- Merge the docbook into the kerneldoc comments.
- Spec in detail the precise semantics of the callbacks.
- For consistency in wording and easier review roll out kerneldoc also
for crtc, encoder and connector for the standard hooks they share
with planes.
v2: Suggestions from Thierry.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449218769-16577-8-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Thierry Reding <treding@nvidia.com>
Daniel Vetter [Fri, 4 Dec 2015 08:45:47 +0000 (09:45 +0100)]
drm/bridge: Improve kerneldoc
Especially document the assumptions and semantics of the callbacks
carefully. Just a warm-up excercise really.
v2: Spelling fixes (Eric).
v3: Consolidate more with existing docs:
- Remove the overview section explaining the bridge funcs, that's
now all in the drm_bridge_funcs kerneldoc in much more detail.
- Use & to reference structs so that kerneldoc automatically inserts
hyperlinks.
v4: Review from Thierry.
Cc: Eric Anholt <eric@anholt.net>
Cc: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Archit Taneja <architt@codeaurora.org> (v3)
Link: http://patchwork.freedesktop.org/patch/msgid/1449218769-16577-7-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Thierry Reding <treding@nvidia.com>
Daniel Vetter [Fri, 4 Dec 2015 08:45:46 +0000 (09:45 +0100)]
drm: Merge helper docbook into kerneldoc comments
Duplication is bad, luckily both help texts highlighted different
issues so the kerneldoc gained quite a bit!
While at it also sprinkle more references to the vtable structs around
and make it clear that legacy CRTC helpers are deprecated and which
functions to use instead.
v2: Spelling fixes and polish (Thierry).
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449218769-16577-6-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Thierry Reding <treding@nvidia.com>
Daniel Vetter [Fri, 4 Dec 2015 08:45:45 +0000 (09:45 +0100)]
drm: Make helper vtable pointers type-safe
Originally the idea behind void* was to allow different sets of
helpers. But now we have that (with probe, plane, crtc and atomic
helpers) and we still just use the same set of vtables. That's the
only way to make the individual helpers modular and allow drivers to
pick&choose and transition between them. So this flexibility isn't
really needed. Also we have lots of non-vtable data meanwhile in core
structures too, this is not the first one at all.
Given that the void * is only trouble since gcc can't warn you if you
mix them up. Let's fix that and make them typesafe.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449218769-16577-5-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Thierry Reding <treding@nvidia.com>
Daniel Vetter [Fri, 4 Dec 2015 08:45:44 +0000 (09:45 +0100)]
drm: Reorganize helper vtables and their docs
Currently we have 4 helper libraries (probe, crtc, plane & atomic)
that all use the same helper vtables. And that's by necessity since we
don't want to litter the core structs with one ops pointer per helper
library. Also often the reuse the same hooks (like atomic does, to
facilite conversion from existing drivers using crtc and plane
helpers).
Given all that it doesn't make sense to put the docs for these next to
specific helpers. Instead extract them into a new header file and
section in the docbook, and add references to them everywhere.
Unfortunately kernel-doc complains when an include directive doesn't
find anything (and it does by dumping crap into the output file). We
have to remove the now empty includes to avoid that, instead of leaving
them in for future proofing.
v2: More OCD in ordering functions.
v3: Spelling plus collate copyright headers properly.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449218769-16577-4-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Thierry Reding <treding@nvidia.com>
Daniel Vetter [Fri, 4 Dec 2015 08:45:43 +0000 (09:45 +0100)]
drm: Move LEAVE/ENTER_ATOMIC_MODESET to fbdev helpers
This is only used for kgdb (and previously panic) handlers in
the fbdev emulation, so belongs there.
Note that this means we'll leave behind a forward declaration, but
once all the helper vtables are consolidated (in the next patch) that
will make more sense.
v2: fixup radone/amdgpu.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449218769-16577-3-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Thierry Reding <treding@nvidia.com> (v2)
Daniel Vetter [Fri, 4 Dec 2015 08:45:42 +0000 (09:45 +0100)]
drm: Polish fbdev helper struct docs
Mostly this is just adding extensive docs for the callbacks, but also
a few other additions.
v2: Use FIXME comments to annotate helper hooks that should be
replaced.
v3: Small nits (Thierry).
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449218769-16577-2-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Thierry Reding <treding@nvidia.com>
Dave Airlie [Tue, 8 Dec 2015 01:04:26 +0000 (11:04 +1000)]
Back merge tag 'v4.4-rc4' into drm-next
We've picked up a few conflicts and it would be nice
to resolve them before we move onwards.
Dave Airlie [Mon, 7 Dec 2015 08:17:09 +0000 (18:17 +1000)]
Merge tag 'topic/drm-misc-2015-12-04' of git://anongit.freedesktop.org/drm-intel into drm-next
New -misc pull. Big thing is Thierry's atomic helpers for system suspend
resume, which I'd like to use in i915 too. Hence the pull.
* tag 'topic/drm-misc-2015-12-04' of git://anongit.freedesktop.org/drm-intel:
drm: keep connector status change logging human readable
drm/atomic-helper: Reject attempts at re-stealing encoders
drm/atomic-helper: Implement subsystem-level suspend/resume
drm: Implement drm_modeset_lock_all_ctx()
drm/gma500: Add driver private mutex for the fault handler
drm/gma500: Drop dev->struct_mutex from mmap offset function
drm/gma500: Drop dev->struct_mutex from fbdev init/teardown code
drm/gma500: Drop dev->struct_mutex from modeset code
drm/gma500: Use correct unref in the gem bo create function
drm/edid: Make the detailed timing CEA/HDMI mode fixup accept up to 5kHz clock difference
drm/atomic_helper: Add drm_atomic_helper_disable_planes_on_crtc()
drm: Serialise multiple event readers
drm: Drop dev->event_lock spinlock around faulting copy_to_user()
Linus Torvalds [Sun, 6 Dec 2015 23:43:12 +0000 (15:43 -0800)]
Linux 4.4-rc4
James Simmons [Fri, 4 Dec 2015 23:23:08 +0000 (18:23 -0500)]
staging/lustre: remove IOC_LIBCFS_PING_TEST ioctl
The ioctl IOC_LIBCFS_PING_TEST has not been used in ages. The recent
nidstring changes which moved all the nidstring operations from libcfs
to the LNet layer but this ioctl code was still using an nidstring
operation that was causing a circular dependency loop between libcfs and
LNet.
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 6 Dec 2015 21:51:49 +0000 (13:51 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A couple of fixes (-stable fodder) + dead code removal after the
overlayfs fix.
I agree that it's better to separate from the fix part to make
backporting easier, but IMO it's not worth delaying said dead code
removal until the next window"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Don't reset ->total_link_count on nested calls of vfs_path_lookup()
ovl: get rid of the dead code left from broken (and disabled) optimizations
ovl: fix permission checking for setattr
Al Viro [Sun, 6 Dec 2015 17:33:02 +0000 (12:33 -0500)]
Don't reset ->total_link_count on nested calls of vfs_path_lookup()
we already zero it on outermost set_nameidata(), so initialization in
path_init() is pointless and wrong. The same DoS exists on pre-4.2
kernels, but there a slightly different fix will be needed.
Cc: stable@vger.kernel.org # v4.2
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sun, 6 Dec 2015 17:31:07 +0000 (12:31 -0500)]
ovl: get rid of the dead code left from broken (and disabled) optimizations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Miklos Szeredi [Fri, 4 Dec 2015 18:18:48 +0000 (19:18 +0100)]
ovl: fix permission checking for setattr
[Al Viro] The bug is in being too enthusiastic about optimizing ->setattr()
away - instead of "copy verbatim with metadata" + "chmod/chown/utimes"
(with the former being always safe and the latter failing in case of
insufficient permissions) it tries to combine these two. Note that copyup
itself will have to do ->setattr() anyway; _that_ is where the elevated
capabilities are right. Having these two ->setattr() (one to set verbatim
copy of metadata, another to do what overlayfs ->setattr() had been asked
to do in the first place) combined is where it breaks.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Sun, 6 Dec 2015 16:35:05 +0000 (08:35 -0800)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull scheduler fixes from Thomas Gleixner:
"This updates contains the following changes:
- Fix a signal handling regression in the bit wait functions.
- Avoid false positive warnings in the wakeup path.
- Initialize the scheduler root domain properly.
- Handle gtime calculations in proc/$PID/stat proper.
- Add more documentation for the barriers in try_to_wake_up().
- Fix a subtle race in try_to_wake_up() which might cause a task to
be scheduled on two cpus
- Compile static helper function only when it is used"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/core: Fix an SMP ordering race in try_to_wake_up() vs. schedule()
sched/core: Better document the try_to_wake_up() barriers
sched/cputime: Fix invalid gtime in proc
sched/core: Clear the root_domain cpumasks in init_rootdomain()
sched/core: Remove false-positive warning from wake_up_process()
sched/wait: Fix signal handling in bit wait helpers
sched/rt: Hide the push_irq_work_func() declaration
Linus Torvalds [Sun, 6 Dec 2015 16:08:56 +0000 (08:08 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Thoma Gleixner:
"Another round of fixes for x86:
- Move the initialization of the microcode driver to late_initcall to
make sure everything that init function needs is available.
- Make sure that lockdep knows about interrupts being off in the
entry code before calling into c-code.
- Undo the cpu hotplug init delay regression.
- Use the proper conditionals in the mpx instruction decoder.
- Fixup restart_syscall for x32 tasks.
- Fix the hugepage regression on PAE kernels which was introduced
with the latest PAT changes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/signal: Fix restart_syscall number for x32 tasks
x86/mpx: Fix instruction decoder condition
x86/mm: Fix regression with huge pages on PAE
x86 smpboot: Re-enable init_udelay=0 by default on modern CPUs
x86/entry/64: Fix irqflag tracing wrt context tracking
x86/microcode: Initialize the driver late when facilities are up
Linus Torvalds [Sun, 6 Dec 2015 16:02:25 +0000 (08:02 -0800)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is quite a bumper crop of fixes: three from Arnd correcting
various build issues in some configurations, a lock recursion in
qla2xxx. Two potentially exploitable issues in hpsa and mvsas, a
potential null deref in st, a revert of a bdi registration fix that
turned out to cause even more problems, a set of fixes to allow people
who only defined MPT2SAS to still work after the mpt2/mpt3sas merger
and a couple of fixes for issues turned up by the hyper-v storvsc
driver"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
mpt3sas: fix Kconfig dependency problem for mpt2sas back compatibility
Revert "scsi: Fix a bdi reregistration race"
mpt3sas: Add dummy Kconfig option for backwards compatibility
Fix a memory leak in scsi_host_dev_release()
block/sd: Fix device-imposed transfer length limits
scsi_debug: fix prevent_allow+verify regressions
MAINTAINERS: Add myself as co-maintainer of the SCSI subsystem.
sd: Make discard granularity match logical block size when LBPRZ=1
scsi: hpsa: select CONFIG_SCSI_SAS_ATTR
scsi: advansys needs ISA dma api for ISA support
scsi_sysfs: protect against double execution of __scsi_remove_device()
st: fix potential null pointer dereference.
scsi: report 'INQUIRY result too short' once per host
advansys: fix big-endian builds
qla2xxx: Fix rwlock recursion
hpsa: logical vs bitwise AND typo
mvsas: don't allow negative timeouts
mpt3sas: Fix use sas_is_tlr_enabled API before enabling MPI2_SCSIIO_CONTROL_TLR_ON flag
Linus Torvalds [Sun, 6 Dec 2015 00:06:30 +0000 (16:06 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"A bunch of change across the board, the main things are some vblank
fallout in radeon and nouveau required some work, but I think this
should fix it all. There is also one drm fix for an oops in vmwgfx
with how we pass the drm master around.
The rest is just some amdgpu, i915, imx and rockchip fixes.
Probably more than I'd like at this point, but hopefully things settle
down now"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (40 commits)
drm/amdgpu: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v3)
drm/radeon: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v2)
drm/radeon: Retry DDC probing on DVI on failure if we got an HPD interrupt
drm/amdgpu: add spin lock to protect freed list in vm (v2)
drm/amdgpu: partially revert "drm/amdgpu: fix VM_CONTEXT*_PAGE_TABLE_END_ADDR" v2
drm/amdgpu: take a BO reference for the user fence
drm/amdgpu: take a BO reference in the display code
drm/amdgpu: set snooped flags only on system addresses v2
drm/nouveau: Fix pre-nv50 pageflip events (v4)
drm: Fix an unwanted master inheritance v2
drm/amdgpu: fix race condition in amd_sched_entity_push_job
drm/amdgpu: add err check for pin userptr
drm/i915: take a power domain reference while checking the HDMI live status
drm/i915: add MISSING_CASE to a few port/aux power domain helpers
drm/i915/ddi: fix intel_display_port_aux_power_domain() after HDMI detect
drm/i915: Introduce a gmbus power domain
drm/i915: Clean up AUX power domain handling
drm/rockchip: Use CRTC vblank event interface
drm/rockchip: Fix module autoload for OF platform driver
drm/rockchip: vop: fix window origin calculation
...
Linus Torvalds [Sat, 5 Dec 2015 18:46:44 +0000 (10:46 -0800)]
Merge branch 'linus' of git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes a couple of crypto drivers that were using memcmp to verify
authentication tags. They now use crypto_memneq instead"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: talitos - Fix timing leak in ESP ICV verification
crypto: nx - Fix timing leak in GCM and CCM decryption
Dmitry V. Levin [Mon, 30 Nov 2015 21:54:36 +0000 (00:54 +0300)]
x86/signal: Fix restart_syscall number for x32 tasks
When restarting a syscall with regs->ax == -ERESTART_RESTARTBLOCK,
regs->ax is assigned to a restart_syscall number. For x32 tasks, this
syscall number must have __X32_SYSCALL_BIT set, otherwise it will be
an x86_64 syscall number instead of a valid x32 syscall number. This
issue has been there since the introduction of x32.
Reported-by: strace/tests/restart_syscall.test
Reported-and-tested-by: Elvira Khabirova <lineprinter0@gmail.com>
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Cc: Elvira Khabirova <lineprinter0@gmail.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20151130215436.GA25996@altlinux.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Dave Hansen [Tue, 1 Dec 2015 00:31:13 +0000 (16:31 -0800)]
x86/mpx: Fix instruction decoder condition
MPX decodes instructions in order to tell which bounds register
was violated. Part of this decoding involves looking at the "REX
prefix" which is a special instrucion prefix used to retrofit
support for new registers in to old instructions.
The X86_REX_*() macros are defined to return actual bit values:
#define X86_REX_R(rex) ((rex) & 4)
*not* boolean values. However, the MPX code was checking for
them like they were booleans. This might have led to us
mis-decoding the "REX prefix" and giving false information out to
userspace about bounds violations. X86_REX_B() actually is bit 1,
so this is really only broken for the X86_REX_X() case.
Fix the conditionals up to tolerate the non-boolean values.
Fixes: fcc7ffd67991 "x86, mpx: Decode MPX instruction to get bound violation information"
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: x86@kernel.org
Cc: Dave Hansen <dave@sr71.net>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20151201003113.D800C1E0@viggo.jf.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Dave Airlie [Sat, 5 Dec 2015 06:15:38 +0000 (16:15 +1000)]
Merge branch 'drm-fixes-4.4' of git://people.freedesktop.org/~agd5f/linux into drm-next
A few more last minute fixes for 4.4 on top of my pull request from
earlier this week. The big change here is a vblank regression fix due to
commit
4dfd6486 "drm: Use vblank timestamps to guesstimate how many vblanks
were missed". Beyond that, a hotplug fix and a few VM fixes.
* 'drm-fixes-4.4' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v3)
drm/radeon: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v2)
drm/radeon: Retry DDC probing on DVI on failure if we got an HPD interrupt
drm/amdgpu: add spin lock to protect freed list in vm (v2)
drm/amdgpu: partially revert "drm/amdgpu: fix VM_CONTEXT*_PAGE_TABLE_END_ADDR" v2
drm/amdgpu: take a BO reference for the user fence
drm/amdgpu: take a BO reference in the display code
drm/amdgpu: set snooped flags only on system addresses v2
drm/amdgpu: fix race condition in amd_sched_entity_push_job
drm/amdgpu: add err check for pin userptr
add blacklist for thinkpad T40p
drm/amdgpu: fix VM page table reference counting
drm/amdgpu: fix userptr flags check
Linus Torvalds [Fri, 4 Dec 2015 20:46:07 +0000 (12:46 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/sage/ceph-client
Pull Ceph fix from Sage Weil:
"This addresses a refcounting bug that leads to a use-after-free"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: don't put snap_context twice in rbd_queue_workfn()
Alex Deucher [Thu, 3 Dec 2015 17:31:56 +0000 (12:31 -0500)]
drm/amdgpu: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v3)
commit
4dfd6486 "drm: Use vblank timestamps to guesstimate how many
vblanks were missed" introduced in Linux 4.4-rc1 makes the drm core
more fragile to drivers which don't update hw vblank counters and
vblank timestamps in sync with firing of the vblank irq and
essentially at leading edge of vblank.
This exposed a problem with radeon-kms/amdgpu-kms which do not
satisfy above requirements:
The vblank irq fires a few scanlines before start of vblank, but
programmed pageflips complete at start of vblank and
vblank timestamps update at start of vblank, whereas the
hw vblank counter increments only later, at start of vsync.
This leads to problems like off by one errors for vblank counter
updates, vblank counters apparently going backwards or vblank
timestamps apparently having time going backwards. The net result
is stuttering of graphics in games, or little hangs, as well as
total failure of timing sensitive applications.
See bug #93147 for an example of the regression on Linux 4.4-rc:
https://bugs.freedesktop.org/show_bug.cgi?id=93147
This patch tries to align all above events better from the
viewpoint of the drm core / of external callers to fix the problem:
1. The apparent start of vblank is shifted a few scanlines earlier,
so the vblank irq now always happens after start of this extended
vblank interval and thereby drm_update_vblank_count() always samples
the updated vblank count and timestamp of the new vblank interval.
To achieve this, the reporting of scanout positions by
radeon_get_crtc_scanoutpos() now operates as if the vblank starts
radeon_crtc->lb_vblank_lead_lines before the real start of the hw
vblank interval. This means that the vblank timestamps which are based
on these scanout positions will now update at this earlier start of
vblank.
2. The driver->get_vblank_counter() function will bump the returned
vblank count as read from the hw by +1 if the query happens after
the shifted earlier start of the vblank, but before the real hw increment
at start of vsync, so the counter appears to increment at start of vblank
in sync with the timestamp update.
3. Calls from vblank irq-context and regular non-irq calls are now
treated identical, always simulating the shifted vblank start, to
avoid inconsistent results for queries happening from vblank irq vs.
happening from drm_vblank_enable() or vblank_disable_fn().
4. The radeon_flip_work_func will delay mmio programming a pageflip until
the start of the real vblank iff it happens to execute inside the shifted
earlier start of the vblank, so pageflips now also appear to execute at
start of the shifted vblank, in sync with vblank counter and timestamp
updates. This to avoid some races between updates of vblank count and
timestamps that are used for swap scheduling and pageflip execution which
could cause pageflips to execute before the scheduled target vblank.
The lb_vblank_lead_lines "fudge" value is calculated as the size of
the display controllers line buffer in scanlines for the given video
mode: Vblank irq's are triggered by the line buffer logic when the line
buffer refill for a video frame ends, ie. when the line buffer source read
position enters the hw vblank. This means that a vblank irq could fire at
most as many scanlines before the current reported scanout position of the
crtc timing generator as the number of scanlines the line buffer can
maximally hold for a given video mode.
This patch has been successfully tested on a RV730 card with DCE-3 display
engine and on a evergreen card with DCE-4 display engine, in single-display
and dual-display configuration, with different video modes.
A similar patch is needed for amdgpu-kms to fix the same problem.
Limitations:
- Maybe replace the udelay() in the flip_work_func() by a suitable
usleep_range() for a bit better efficiency? Will try that.
- Line buffer sizes in pixels are hard-coded on < DCE-4 to a value
i just guessed to be high enough to work ok, lacking info on the true
sizes atm.
Probably fixes: fdo#93147
Port of Mario's radeon fix to amdgpu.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(v1) Reviewed-by: Mario Kleiner <mario.kleiner.de@gmail.com>
(v2) Refine amdgpu_flip_work_func() for better efficiency.
In amdgpu_flip_work_func, replace the busy waiting udelay(5)
with event lock held by a more performance and energy efficient
usleep_range() until at least predicted true start of hw vblank,
with some slack for scheduler happiness. Release the event lock
during waits to not delay other outputs in doing their stuff, as
the waiting can last up to 200 usecs in some cases.
Also small fix to code comment and formatting in that function.
(v2) Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
(v3) Fix crash in crtc disabled case
Linus Torvalds [Fri, 4 Dec 2015 19:30:45 +0000 (11:30 -0800)]
Merge branch 'libnvdimm-fixes' of git://git./linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
- NFIT parsing regression fixes from Linda. The nvdimm hot-add
implementation merged in 4.4-rc1 interpreted the specification in a
way that breaks actual HPE platforms. We are also closing the loop
with the ACPI Working Group to get this clarification added to the
spec.
- Andy pointed out that his laptop without nvdimm resources is loading
the e820-nvdimm module by default, fix that up to only load the
module when an e820-type-12 range is present.
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit: Adjust for different _FIT and NFIT headers
nfit: Fix the check for a successful NFIT merge
nfit: Account for table size length variation
libnvdimm, e820: skip module loading when no type-12
Linus Torvalds [Fri, 4 Dec 2015 18:17:20 +0000 (10:17 -0800)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull ARM KVM fixes from Paolo Bonzini:
- a series of fixes to deal with the aliasing between the sp and xzr
register
- a fix for the cache flush fix that went in -rc3
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
ARM/arm64: KVM: correct PTE uncachedness check
arm64: KVM: Get rid of old vcpu_reg()
arm64: KVM: Correctly handle zero register in system register accesses
arm64: KVM: Remove const from struct sys_reg_params
arm64: KVM: Correctly handle zero register during MMIO
Mario Kleiner [Wed, 25 Nov 2015 19:14:31 +0000 (20:14 +0100)]
drm/radeon: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v2)
commit
4dfd6486 "drm: Use vblank timestamps to guesstimate how many
vblanks were missed" introduced in Linux 4.4-rc1 makes the drm core
more fragile to drivers which don't update hw vblank counters and
vblank timestamps in sync with firing of the vblank irq and
essentially at leading edge of vblank.
This exposed a problem with radeon-kms/amdgpu-kms which do not
satisfy above requirements:
The vblank irq fires a few scanlines before start of vblank, but
programmed pageflips complete at start of vblank and
vblank timestamps update at start of vblank, whereas the
hw vblank counter increments only later, at start of vsync.
This leads to problems like off by one errors for vblank counter
updates, vblank counters apparently going backwards or vblank
timestamps apparently having time going backwards. The net result
is stuttering of graphics in games, or little hangs, as well as
total failure of timing sensitive applications.
See bug #93147 for an example of the regression on Linux 4.4-rc:
https://bugs.freedesktop.org/show_bug.cgi?id=93147
This patch tries to align all above events better from the
viewpoint of the drm core / of external callers to fix the problem:
1. The apparent start of vblank is shifted a few scanlines earlier,
so the vblank irq now always happens after start of this extended
vblank interval and thereby drm_update_vblank_count() always samples
the updated vblank count and timestamp of the new vblank interval.
To achieve this, the reporting of scanout positions by
radeon_get_crtc_scanoutpos() now operates as if the vblank starts
radeon_crtc->lb_vblank_lead_lines before the real start of the hw
vblank interval. This means that the vblank timestamps which are based
on these scanout positions will now update at this earlier start of
vblank.
2. The driver->get_vblank_counter() function will bump the returned
vblank count as read from the hw by +1 if the query happens after
the shifted earlier start of the vblank, but before the real hw increment
at start of vsync, so the counter appears to increment at start of vblank
in sync with the timestamp update.
3. Calls from vblank irq-context and regular non-irq calls are now
treated identical, always simulating the shifted vblank start, to
avoid inconsistent results for queries happening from vblank irq vs.
happening from drm_vblank_enable() or vblank_disable_fn().
4. The radeon_flip_work_func will delay mmio programming a pageflip until
the start of the real vblank iff it happens to execute inside the shifted
earlier start of the vblank, so pageflips now also appear to execute at
start of the shifted vblank, in sync with vblank counter and timestamp
updates. This to avoid some races between updates of vblank count and
timestamps that are used for swap scheduling and pageflip execution which
could cause pageflips to execute before the scheduled target vblank.
The lb_vblank_lead_lines "fudge" value is calculated as the size of
the display controllers line buffer in scanlines for the given video
mode: Vblank irq's are triggered by the line buffer logic when the line
buffer refill for a video frame ends, ie. when the line buffer source read
position enters the hw vblank. This means that a vblank irq could fire at
most as many scanlines before the current reported scanout position of the
crtc timing generator as the number of scanlines the line buffer can
maximally hold for a given video mode.
This patch has been successfully tested on a RV730 card with DCE-3 display
engine and on a evergreen card with DCE-4 display engine, in single-display
and dual-display configuration, with different video modes.
A similar patch is needed for amdgpu-kms to fix the same problem.
Limitations:
- Line buffer sizes in pixels are hard-coded on < DCE-4 to a value
i just guessed to be high enough to work ok, lacking info on the true
sizes atm.
Fixes: fdo#93147
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Michel Dänzer <michel.daenzer@amd.com>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
(v1) Tested-by: Dave Witbrodt <dawitbro@sbcglobal.net>
(v2) Refine radeon_flip_work_func() for better efficiency:
In radeon_flip_work_func, replace the busy waiting udelay(5)
with event lock held by a more performance and energy efficient
usleep_range() until at least predicted true start of hw vblank,
with some slack for scheduler happiness. Release the event lock
during waits to not delay other outputs in doing their stuff, as
the waiting can last up to 200 usecs in some cases.
Retested on DCE-3 and DCE-4 to verify it still works nicely.
(v2) Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Lyude [Thu, 3 Dec 2015 23:26:07 +0000 (18:26 -0500)]
drm/radeon: Retry DDC probing on DVI on failure if we got an HPD interrupt
HPD signals on DVI ports can be fired off before the pins required for
DDC probing actually make contact, due to the pins for HPD making
contact first. This results in a HPD signal being asserted but DDC
probing failing, resulting in hotplugging occasionally failing.
This is somewhat rare on most cards (depending on what angle you plug
the DVI connector in), but on some cards it happens constantly. The
Radeon R5 on the machine used for testing this patch for instance, runs
into this issue just about every time I try to hotplug a DVI monitor and
as a result hotplugging almost never works.
Rescheduling the hotplug work for a second when we run into an HPD
signal with a failing DDC probe usually gives enough time for the rest
of the connector's pins to make contact, and fixes this issue.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
jimqu [Fri, 4 Dec 2015 09:17:00 +0000 (17:17 +0800)]
drm/amdgpu: add spin lock to protect freed list in vm (v2)
there is a protection fault about freed list when OCL test.
add a spin lock to protect it.
v2: drop changes in vm_fini
Signed-off-by: JimQu <jim.qu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Christian König [Thu, 3 Dec 2015 19:54:35 +0000 (20:54 +0100)]
drm/amdgpu: partially revert "drm/amdgpu: fix VM_CONTEXT*_PAGE_TABLE_END_ADDR" v2
The gtt_end is already inclusive, we don't need to subtract one here.
v2 (chk): keep the fix for the VM code, cause here it really applies.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Anatoli Antonovitch <anatoli.antonovitch@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Thu, 3 Dec 2015 18:55:52 +0000 (19:55 +0100)]
drm/amdgpu: take a BO reference for the user fence
No need for a GEM reference here.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Thu, 3 Dec 2015 18:55:51 +0000 (19:55 +0100)]
drm/amdgpu: take a BO reference in the display code
No need for the GEM reference here.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Paolo Bonzini [Fri, 4 Dec 2015 17:32:32 +0000 (18:32 +0100)]
Merge tag 'kvm-arm-for-v4.4-rc4' of git://git./linux/kernel/git/kvmarm/kvmarm into kvm-master
KVM/ARM fixes for v4.4-rc4
- A series of fixes to deal with the aliasing between the sp and xzr register
- A fix for the cache flush fix that went in -rc3
Christian König [Fri, 4 Dec 2015 12:32:55 +0000 (13:32 +0100)]
drm/amdgpu: set snooped flags only on system addresses v2
Not necessary for VRAM.
v2: no need to check if ttm is NULL.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Linus Torvalds [Fri, 4 Dec 2015 17:16:26 +0000 (09:16 -0800)]
Merge tag 'sound-4.4-rc4' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This time we've got a larger number of updates, mainly from ASoC
world. The only significant LOCs found here are for Realtek codecs,
where most of changes are quite systematic replacements.
There are also a few fixes in ASoC core side: one is the PM call order
fix to ensure the DPAM resume working properly. Another is the proper
cleanup call after freeing DAPM widgets, and the correction of the
wrong callback set in topology API.
The rest are a wide range of driver-specific small fixes, including
HD-audio"
* tag 'sound-4.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (35 commits)
ALSA: hda - Add Conexant CX8200 (14f1:2008) codec entry
ALSA: hda - Correct codec names for 14f1:50f1 and 14f1:50f3
ALSA: hda - Skip ELD notification during system suspend
ASoC: core: Change power state before rechecking endpoint
ASoC: fix kernel-doc warnings in sound/soc/soc-ops.c
ASoC: rt5645: Add dmi_system_id "Google Terra"
ASoC: rockchip: Fix incorrect VDW value for 24 bit
ASoC: fsl: clarify ac97 dependency
ASoC: Intel: Skylake: fix memory leak
ASoC: davinci-mcasp: Fix master capture only mode
ASoC: es8328: Fix shifts for mixer switches
ASoC: rt5645: Add dmi_system_id "Google Wizpig"
ASoC: sti: set player private data
ASoC: sti: rename ST proprietary DT properties
ASoC: sti: remove wrong error message
ASoC: Intel: Skylake: Add I2C depends for SKL machine
ASoC: topology: fix info callback for TLV byte control
ASoC: rt5670: fix wrong bit def for pll src
ASoC: nau8825: add pm function
ASoC: rt5645: Add struct dmi_system_id "Google Edgar" for Chrome OS
...
Linus Torvalds [Fri, 4 Dec 2015 16:59:10 +0000 (08:59 -0800)]
Merge tag 'pm+acpi-4.4-rc4' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These fix a recent regression in the ACPI PCI host bridge
initialization code, clean up some recent changes (generic power
domains framework, ACPI AML debugger support), fix three older but
annoying bugs (PCI power management. generic power domains framework,
cpufreq) and a build problem (device properties framework), and update
a stale MAINTAINERS entry (ACPI backlight driver).
Specifics:
- Fix a regression in the ACPI PCI host bridge initialization code
introduced by the recent consolidation of the host bridge handling
on x86 and ia64 that forgot to take one special piece of code
related to NUMA on x86 into account (Liu Jiang).
- Improve the Kconfig help description of the new ACPI AML debugger
support option to avoid possible confusion (Peter Zijlstra).
- Remove a piece of code in the generic power domains framework that
should have been removed by one of the recent commits modifying
that code (Ulf Hansson).
- Reduce the log level of a PCI PM message that generates a lot of
false-positive log noise for some drivers and improve the message
itself while at it (Imre Deak).
- Fix the OF-based domain lookup code in the generic power domains
framework to make it drop references to DT nodes correctly (Eric
Anholt).
- Prevent the cpufreq core from setting the policy back to the
default after a CPU offline/online cycle for cpufreq drivers
providing the ->setpolicy callback (Srinivas Pandruvada).
- Fix a build problem for CONFIG_ACPI unset in the device properties
framework (Hanjun Guo).
- Fix a stale file path in the ACPI backlight driver entry in
MAINTAINERS (Dan Carpenter)"
* tag 'pm+acpi-4.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Domains: Fix bad of_node_put() in failure paths of genpd_dev_pm_attach()
cpufreq: use last policy after online for drivers with ->setpolicy
PCI / PM: Tune down retryable runtime suspend error messages
PM / Domains: Validate cases of a non-bound driver in genpd governor
MAINTAINERS: ACPI / video: update a file name in drivers/acpi/
ACPI / property: fix compile error for acpi_node_get_property_reference() when CONFIG_ACPI=n
x86/PCI/ACPI: Fix regression caused by commit
4d6b4e69a245
ACPI: Better describe ACPI_DEBUGGER
Ard Biesheuvel [Thu, 3 Dec 2015 08:25:22 +0000 (09:25 +0100)]
ARM/arm64: KVM: correct PTE uncachedness check
Commit
e6fab5442345 ("ARM/arm64: KVM: test properly for a PTE's
uncachedness") modified the logic to test whether a HYP or stage-2
mapping needs flushing, from [incorrectly] interpreting the page table
attributes to [incorrectly] checking whether the PFN that backs the
mapping is covered by host system RAM. The PFN number is part of the
output of the translation, not the input, so we have to use pte_pfn()
on the contents of the PTE, not __phys_to_pfn() on the HYP virtual
address or stage-2 intermediate physical address.
Fixes: e6fab5442345 ("ARM/arm64: KVM: test properly for a PTE's uncachedness")
Cc: stable@vger.kernel.org
Tested-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pavel Fedin [Fri, 4 Dec 2015 12:03:14 +0000 (15:03 +0300)]
arm64: KVM: Get rid of old vcpu_reg()
Using oldstyle vcpu_reg() accessor is proven to be inappropriate and
unsafe on ARM64. This patch converts the rest of use cases to new
accessors and completely removes vcpu_reg() on ARM64.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pavel Fedin [Fri, 4 Dec 2015 12:03:13 +0000 (15:03 +0300)]
arm64: KVM: Correctly handle zero register in system register accesses
System register accesses also use zero register for Rt == 31, and
therefore using it will also result in getting SP value instead. This
patch makes them also using new accessors, introduced by the previous
patch. Since register value is no longer directly associated with storage
inside vCPU context structure, we introduce a dedicated storage for it in
struct sys_reg_params.
This refactor also gets rid of "massive hack" in kvm_handle_cp_64().
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pavel Fedin [Fri, 4 Dec 2015 12:03:12 +0000 (15:03 +0300)]
arm64: KVM: Remove const from struct sys_reg_params
Further rework is going to introduce a dedicated storage for transfer
register value in struct sys_reg_params. Before doing this we have to
remove 'const' modifiers from it in all accessor functions and their
callers.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pavel Fedin [Fri, 4 Dec 2015 12:03:11 +0000 (15:03 +0300)]
arm64: KVM: Correctly handle zero register during MMIO
On ARM64 register index of 31 corresponds to both zero register and SP.
However, all memory access instructions, use ZR as transfer register. SP
is used only as a base register in indirect memory addressing, or by
register-register arithmetics, which cannot be trapped here.
Correct emulation is achieved by introducing new register accessor
functions, which can do special handling for reg_num == 31. These new
accessors intentionally do not rely on old vcpu_reg() on ARM64, because
it is to be removed. Since the affected code is shared by both ARM
flavours, implementations of these accessors are also added to ARM32 code.
This patch fixes setting MMIO register to a random value (actually SP)
instead of zero by something like:
*((volatile int *)reg) = 0;
compilers tend to generate "str wzr, [xx]" here
[Marc: Fixed 32bit splat]
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Ilya Dryomov [Fri, 27 Nov 2015 18:23:24 +0000 (19:23 +0100)]
rbd: don't put snap_context twice in rbd_queue_workfn()
Commit
4e752f0ab0e8 ("rbd: access snapshot context and mapping size
safely") moved ceph_get_snap_context() out of rbd_img_request_create()
and into rbd_queue_workfn(), adding a ceph_put_snap_context() to the
error path in rbd_queue_workfn(). However, rbd_img_request_create()
consumes a ref on snapc, so calling ceph_put_snap_context() after
a successful rbd_img_request_create() leads to an extra put. Fix it.
Cc: stable@vger.kernel.org # 3.18+
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Josh Durgin <jdurgin@redhat.com>
Rafael J. Wysocki [Fri, 4 Dec 2015 13:01:42 +0000 (14:01 +0100)]
Merge branches 'pm-domains' and 'pm-cpufreq'
* pm-domains:
PM / Domains: Fix bad of_node_put() in failure paths of genpd_dev_pm_attach()
PM / Domains: Validate cases of a non-bound driver in genpd governor
* pm-cpufreq:
cpufreq: use last policy after online for drivers with ->setpolicy
Rafael J. Wysocki [Fri, 4 Dec 2015 13:01:17 +0000 (14:01 +0100)]
Merge branches 'acpica', 'acpi-video' and 'device-properties'
* acpica:
ACPI: Better describe ACPI_DEBUGGER
* acpi-video:
MAINTAINERS: ACPI / video: update a file name in drivers/acpi/
* device-properties:
ACPI / property: fix compile error for acpi_node_get_property_reference() when CONFIG_ACPI=n
Rafael J. Wysocki [Fri, 4 Dec 2015 13:01:02 +0000 (14:01 +0100)]
Merge branches 'acpi-pci' and 'pm-pci'
* acpi-pci:
x86/PCI/ACPI: Fix regression caused by commit
4d6b4e69a245
* pm-pci:
PCI / PM: Tune down retryable runtime suspend error messages
Peter Zijlstra [Wed, 7 Oct 2015 12:14:13 +0000 (14:14 +0200)]
sched/core: Fix an SMP ordering race in try_to_wake_up() vs. schedule()
Oleg noticed that its possible to falsely observe p->on_cpu == 0 such
that we'll prematurely continue with the wakeup and effectively run p on
two CPUs at the same time.
Even though the overlap is very limited; the task is in the middle of
being scheduled out; it could still result in corruption of the
scheduler data structures.
CPU0 CPU1
set_current_state(...)
<preempt_schedule>
context_switch(X, Y)
prepare_lock_switch(Y)
Y->on_cpu = 1;
finish_lock_switch(X)
store_release(X->on_cpu, 0);
try_to_wake_up(X)
LOCK(p->pi_lock);
t = X->on_cpu; // 0
context_switch(Y, X)
prepare_lock_switch(X)
X->on_cpu = 1;
finish_lock_switch(Y)
store_release(Y->on_cpu, 0);
</preempt_schedule>
schedule();
deactivate_task(X);
X->on_rq = 0;
if (X->on_rq) // false
if (t) while (X->on_cpu)
cpu_relax();
context_switch(X, ..)
finish_lock_switch(X)
store_release(X->on_cpu, 0);
Avoid the load of X->on_cpu being hoisted over the X->on_rq load.
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Peter Zijlstra [Tue, 6 Oct 2015 12:36:17 +0000 (14:36 +0200)]
sched/core: Better document the try_to_wake_up() barriers
Explain how the control dependency and smp_rmb() end up providing
ACQUIRE semantics and pair with smp_store_release() in
finish_lock_switch().
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Hiroshi Shimamoto [Thu, 19 Nov 2015 15:47:28 +0000 (16:47 +0100)]
sched/cputime: Fix invalid gtime in proc
/proc/stats shows invalid gtime when the thread is running in guest.
When vtime accounting is not enabled, we cannot get a valid delta.
The delta is calculated with now - tsk->vtime_snap, but tsk->vtime_snap
is only updated when vtime accounting is runtime enabled.
This patch makes task_gtime() just return gtime without computing the
buggy non-existing tickless delta when vtime accounting is not enabled.
Use context_tracking_is_enabled() to check if vtime is accounting on
some cpu, in which case only we need to check the tickless delta. This
way we fix the gtime value regression on machines not running nohz full.
The kernel config contains CONFIG_VIRT_CPU_ACCOUNTING_GEN=y and
CONFIG_NO_HZ_FULL_ALL=n and boot without nohz_full.
I ran and stop a busy loop in VM and see the gtime in host.
Dump the 43rd field which shows the gtime in every second:
# while :; do awk '{print $3" "$43}' /proc/3955/task/4014/stat; sleep 1; done
S 4348
R
7064566
R
7064766
R
7064967
R
7065168
S 4759
S 4759
During running busy loop, it returns large value.
After applying this patch, we can see right gtime.
# while :; do awk '{print $3" "$43}' /proc/10913/task/10956/stat; sleep 1; done
S 5338
R 5365
R 5465
R 5566
R 5666
S 5726
S 5726
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul E . McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1447948054-28668-2-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Xunlei Pang [Wed, 2 Dec 2015 11:52:59 +0000 (19:52 +0800)]
sched/core: Clear the root_domain cpumasks in init_rootdomain()
root_domain::rto_mask allocated through alloc_cpumask_var()
contains garbage data, this may cause problems. For instance,
When doing pull_rt_task(), it may do useless iterations if
rto_mask retains some extra garbage bits. Worse still, this
violates the isolated domain rule for clustered scheduling
using cpuset, because the tasks(with all the cpus allowed)
belongs to one root domain can be pulled away into another
root domain.
The patch cleans the garbage by using zalloc_cpumask_var()
instead of alloc_cpumask_var() for root_domain::rto_mask
allocation, thereby addressing the issues.
Do the same thing for root_domain's other cpumask memembers:
dlo_mask, span, and online.
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1449057179-29321-1-git-send-email-xlpang@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Sasha Levin [Tue, 1 Dec 2015 01:34:20 +0000 (20:34 -0500)]
sched/core: Remove false-positive warning from wake_up_process()
Because wakeups can (fundamentally) be late, a task might not be in
the expected state. Therefore testing against a task's state is racy,
and can yield false positives.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: oleg@redhat.com
Fixes: 9067ac85d533 ("wake_up_process() should be never used to wakeup a TASK_STOPPED/TRACED task")
Link: http://lkml.kernel.org/r/1448933660-23082-1-git-send-email-sasha.levin@oracle.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Peter Zijlstra [Tue, 1 Dec 2015 13:04:04 +0000 (14:04 +0100)]
sched/wait: Fix signal handling in bit wait helpers
Vladimir reported getting RCU stall warnings and bisected it back to
commit:
743162013d40 ("sched: Remove proliferation of wait_on_bit() action functions")
That commit inadvertently reversed the calls to schedule() and signal_pending(),
thereby not handling the case where the signal receives while we sleep.
Reported-by: Vladimir Murzin <vladimir.murzin@arm.com>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: mark.rutland@arm.com
Cc: neilb@suse.de
Cc: oleg@redhat.com
Fixes: 743162013d40 ("sched: Remove proliferation of wait_on_bit() action functions")
Fixes: cbbce8220949 ("SCHED: add some "wait..on_bit...timeout()" interfaces.")
Link: http://lkml.kernel.org/r/20151201130404.GL3816@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Kirill A. Shutemov [Mon, 30 Nov 2015 10:10:33 +0000 (11:10 +0100)]
x86/mm: Fix regression with huge pages on PAE
Recent PAT patchset has caused issue on 32-bit PAE machines:
page:
eea45000 count:0 mapcount:-128 mapping: (null) index:0x0 flags: 0x40000000()
page dumped because: VM_BUG_ON_PAGE(page_mapcount(page) < 0)
------------[ cut here ]------------
kernel BUG at /home/build/linux-boris/mm/huge_memory.c:1485!
invalid opcode: 0000 [#1] SMP
[...]
Call Trace:
unmap_single_vma
? __wake_up
unmap_vmas
unmap_region
do_munmap
vm_munmap
SyS_munmap
do_fast_syscall_32
? __do_page_fault
sysenter_past_esp
Code: ...
EIP: [<
c11bde80>] zap_huge_pmd+0x240/0x260 SS:ESP 0068:
f6459d98
The problem is in pmd_pfn_mask() and pmd_flags_mask(). These
helpers use PMD_PAGE_MASK to calculate resulting mask.
PMD_PAGE_MASK is 'unsigned long', not 'unsigned long long' as
phys_addr_t is on 32-bit PAE (ARCH_PHYS_ADDR_T_64BIT). As a
result, the upper bits of resulting mask get truncated.
pud_pfn_mask() and pud_flags_mask() aren't problematic since we
don't have PUD page table level on 32-bit systems, but it's
reasonable to keep them consistent with PMD counterpart.
Introduce PHYSICAL_PMD_PAGE_MASK and PHYSICAL_PUD_PAGE_MASK in
addition to existing PHYSICAL_PAGE_MASK and reworks helpers to
use them.
Reported-and-Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
[ Fix -Woverflow warnings from the realmode code. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jürgen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: elliott@hpe.com
Cc: konrad.wilk@oracle.com
Cc: linux-mm <linux-mm@kvack.org>
Fixes: f70abb0fc3da ("x86/asm: Fix pud/pmd interfaces to handle large PAT bit")
Link: http://lkml.kernel.org/r/1448878233-11390-2-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Jani Nikula [Thu, 3 Dec 2015 12:00:03 +0000 (14:00 +0200)]
drm: keep connector status change logging human readable
We've had human readable connector status change debug logging since
commit
ed7951dc13aad4a14695ec8122e9f0e2ef25d39e
Author: Lespiau, Damien <damien.lespiau@intel.com>
Date: Fri May 10 12:36:42 2013 +0000
drm: Make the HPD status updates debug logs more readable
but
commit
162b6a57ac50eec236530a16c071ffa50e87362a
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Jan 21 08:45:21 2015 +0100
drm/probe-helper: don't lose hotplug event
added a new one with just the numbers. Fix it.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449144003-2877-1-git-send-email-jani.nikula@intel.com
Daniel Vetter [Tue, 10 Nov 2015 16:37:31 +0000 (17:37 +0100)]
drm/nouveau: Fix pre-nv50 pageflip events (v4)
Apparently pre-nv50 pageflip events happen before the actual vblank
period. Therefore that functionality got semi-disabled in
commit
af4870e406126b7ac0ae7c7ce5751f25ebe60f28
Author: Mario Kleiner <mario.kleiner.de@gmail.com>
Date: Tue May 13 00:42:08 2014 +0200
drm/nouveau/kms/nv04-nv40: fix pageflip events via special case.
Unfortunately that hack got uprooted in
commit
cc1ef118fc099295ae6aabbacc8af94d8d8885eb
Author: Thierry Reding <treding@nvidia.com>
Date: Wed Aug 12 17:00:31 2015 +0200
drm/irq: Make pipe unsigned and name consistent
Triggering a warning when trying to sample the vblank timestamp for a
non-existing pipe. There's a few ways to fix this:
- Open-code the old behaviour, which just enshrines this slight
breakage of the userspace ABI.
- Revert Mario's commit and again inflict broken timestamps, again not
pretty.
- Fix this for real by delaying the pageflip TS until the next vblank
interrupt, thereby making it accurate.
This patch implements the third option. Since having a page flip
interrupt that happens when the pageflip gets armed and not when it
completes in the next vblank seems to be fairly common (older i915 hw
works very similarly) create a new helper to arm vblank events for
such drivers.
v2 (Mario Kleiner):
- Fix function prototypes in drmP.h
- Add missing vblank_put() for pageflip completion without
pageflip event.
- Initialize sequence number for queued pageflip event to avoid
trouble in drm_handle_vblank_events().
- Remove dead code and spelling fix.
v3 (Mario Kleiner):
- Add a signed-off-by and cc stable tag per Ilja's advice.
v4 (Thierry Reding):
- Fix kerneldoc typo, discovered by Michel Dänzer
- Rearrange tags and changelog
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=106431
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mario Kleiner <mario.kleiner.de@gmail.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: stable@vger.kernel.org # v4.3
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Thomas Hellstrom [Wed, 2 Dec 2015 17:24:46 +0000 (09:24 -0800)]
drm: Fix an unwanted master inheritance v2
A client calling drmSetMaster() using a file descriptor that was opened
when another client was master would inherit the latter client's master
object and all its authenticated clients.
This is unwanted behaviour, and when this happens, instead allocate a
brand new master object for the client calling drmSetMaster().
Fixes a BUG() throw in vmw_master_set().
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Fri, 4 Dec 2015 02:26:29 +0000 (12:26 +1000)]
Merge tag 'imx-drm-fixes-2015-12-01' of git://git.pengutronix.de/git/pza/linux into drm-fixes
imx-drm crtc, plane, parallel panel, and TV encoder fixes
- Use drm_crtc_send_vblank_event to fix per crtc vblank handling
- Move the crtc device of_node assignment out of the ipuv3-crtc driver into
ipu-common code, where the devices are created.
- Fix parallel display support with simple-panels
- Remove some unused fields and superfluous checks
- Switch to universal planes and add error handling for primary plane creation
- Fix module autoload for TV encoder driver
* tag 'imx-drm-fixes-2015-12-01' of git://git.pengutronix.de/git/pza/linux:
drm: imx: imx-tve: Fix module autoload for OF platform driver
drm: imx: convert to drm_crtc_send_vblank_event()
GPU-DRM-IMX: Delete an unnecessary check before drm_fbdev_cma_restore_mode()
drm/imx: Remove of_node assignment from ipuv3-crtc driver probe
gpu: ipu-v3: Assign of_node of child platform devices to corresponding ports
gpu: ipu-v3: Remove reg_offset field
gpu: ipu-v3: drop unused dmfc field from client platform data
drm/imx: parallel-display: allow to determine bus format from the connected panel
drm/imx: ipuv3-crtc: Return error if ipu_plane_init() fails for primary plane
drm/imx: switch to universal planes
Dave Airlie [Fri, 4 Dec 2015 02:23:13 +0000 (12:23 +1000)]
Merge tag 'drm-intel-fixes-2015-12-03' of git://anongit.freedesktop.org/drm-intel into drm-fixes
Another batch of drm/i915 fixes for v4.4, on top of the ones from
earlier this week. One timeout handling regression fix from Chris, and
backport of five patches from our -next to fix a power management
related HDMI hotplug regression.
* tag 'drm-intel-fixes-2015-12-03' of git://anongit.freedesktop.org/drm-intel:
drm/i915: take a power domain reference while checking the HDMI live status
drm/i915: add MISSING_CASE to a few port/aux power domain helpers
drm/i915/ddi: fix intel_display_port_aux_power_domain() after HDMI detect
drm/i915: Introduce a gmbus power domain
drm/i915: Clean up AUX power domain handling
drm/i915: Check the timeout passed to i915_wait_request
Eric Anholt [Tue, 1 Dec 2015 17:39:31 +0000 (09:39 -0800)]
PM / Domains: Fix bad of_node_put() in failure paths of genpd_dev_pm_attach()
It looks like these meant to be unreffing the
of_parse_phandle_with_args() node, since the error paths above it
don't do of_node_put. That function returns a new ref in pd_args.np,
though, not a new ref on dev->of_node. Also, it would have leaked the
ref in the success case.
Fixes "ERROR: Bad of_node_put()" on bcm2835 in the -EPROBE_DEFER case.
Fixes: aa42240ab254 (PM / Domains: Add generic OF-based PM domain look-up)
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Cc: 3.18+ <stable@vger.kernel.org> # 3.18+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Fri, 4 Dec 2015 00:02:46 +0000 (16:02 -0800)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
"A lot of Thanksgiving turkey leftovers accumulated, here goes:
1) Fix bluetooth l2cap_chan object leak, from Johan Hedberg.
2) IDs for some new iwlwifi chips, from Oren Givon.
3) Fix rtlwifi lockups on boot, from Larry Finger.
4) Fix memory leak in fm10k, from Stephen Hemminger.
5) We have a route leak in the ipv6 tunnel infrastructure, fix from
Paolo Abeni.
6) Fix buffer pointer handling in arm64 bpf JIT,f rom Zi Shen Lim.
7) Wrong lockdep annotations in tcp md5 support, fix from Eric
Dumazet.
8) Work around some middle boxes which prevent proper handling of TCP
Fast Open, from Yuchung Cheng.
9) TCP repair can do huge kmalloc() requests, build paged SKBs
instead. From Eric Dumazet.
10) Fix msg_controllen overflow in scm_detach_fds, from Daniel
Borkmann.
11) Fix device leaks on ipmr table destruction in ipv4 and ipv6, from
Nikolay Aleksandrov.
12) Fix use after free in epoll with AF_UNIX sockets, from Rainer
Weikusat.
13) Fix double free in VRF code, from Nikolay Aleksandrov.
14) Fix skb leaks on socket receive queue in tipc, from Ying Xue.
15) Fix ifup/ifdown crach in xgene driver, from Iyappan Subramanian.
16) Fix clearing of persistent array maps in bpf, from Daniel
Borkmann.
17) In TCP, for the cross-SYN case, we don't initialize tp->copied_seq
early enough. From Eric Dumazet.
18) Fix out of bounds accesses in bpf array implementation when
updating elements, from Daniel Borkmann.
19) Fill gaps in RCU protection of np->opt in ipv6 stack, from Eric
Dumazet.
20) When dumping proxy neigh entries, we have to accomodate NULL
device pointers properly, from Konstantin Khlebnikov.
21) SCTP doesn't release all ipv6 socket resources properly, fix from
Eric Dumazet.
22) Prevent underflows of sch->q.qlen for multiqueue packet
schedulers, also from Eric Dumazet.
23) Fix MAC and unicast list handling in bnxt_en driver, from Jeffrey
Huang and Michael Chan.
24) Don't actively scan radar channels, from Antonio Quartulli"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (110 commits)
net: phy: reset only targeted phy
bnxt_en: Setup uc_list mac filters after resetting the chip.
bnxt_en: enforce proper storing of MAC address
bnxt_en: Fixed incorrect implementation of ndo_set_mac_address
net: lpc_eth: remove irq > NR_IRQS check from probe()
net_sched: fix qdisc_tree_decrease_qlen() races
openvswitch: fix hangup on vxlan/gre/geneve device deletion
ipv4: igmp: Allow removing groups from a removed interface
ipv6: sctp: implement sctp_v6_destroy_sock()
arm64: bpf: add 'store immediate' instruction
ipv6: kill sk_dst_lock
ipv6: sctp: add rcu protection around np->opt
net/neighbour: fix crash at dumping device-agnostic proxy entries
sctp: use GFP_USER for user-controlled kmalloc
sctp: convert sack_needed and sack_generation to bits
ipv6: add complete rcu protection around np->opt
bpf: fix allocation warnings in bpf maps and integer overflow
mvebu: dts: enable IP checksum with jumbo frames for Armada 38x on Port0
net: mvneta: enable setting custom TX IP checksum limit
net: mvneta: fix error path for building skb
...
Linus Torvalds [Thu, 3 Dec 2015 23:45:16 +0000 (15:45 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A collection of fixes from this series. The most important here is a
regression fix for an issue that some folks would hit in blk-merge.c,
and the NVMe queue depth limit for the screwed up Apple "nvme"
controller.
In more detail, this pull request contains:
- a set of fixes for null_blk, including a fix for a few corner cases
where we could hang the device. From Arianna and Paolo.
- lightnvm:
- A build improvement from Keith.
- Update the qemu pci id detection from Matias.
- Error handling fixes for leaks and other little fixes from
Sudip and Wenwei.
- fix from Eric where BLKRRPART would not return EBUSY for whole
device mounts, only when partitions were mounted.
- fix from Jan Kara, where EOF O_DIRECT reads would return
negatively.
- remove check for rq_mergeable() when checking limits for cloned
requests. The check doesn't make any sense. It's assuming that
since NOMERGE is set on the request that we don't have to
recalculate limits since the request didn't change, but that's not
true if the request has been redirected. From Hannes.
- correctly get the bio front segment value set for single segment
bio's, fixing a BUG() in blk-merge. From Ming"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvme: temporary fix for Apple controller reset
null_blk: change type of completion_nsec to unsigned long
null_blk: guarantee device restart in all irq modes
null_blk: set a separate timer for each command
blk-merge: fix computing bio->bi_seg_front_size in case of single segment
direct-io: Fix negative return from dio read beyond eof
block: Always check queue limits for cloned requests
lightnvm: missing nvm_lock acquire
lightnvm: unconverted ppa returned in get_bb_tbl
lightnvm: refactor and change vendor id for qemu
lightnvm: do device max sectors boundary check first
lightnvm: fix ioctl memory leaks
lightnvm: free memory when gennvm register fails
lightnvm: Simplify config when disabled
Return EBUSY from BLKRRPART for mounted whole-dev fs
Linus Torvalds [Thu, 3 Dec 2015 23:23:17 +0000 (15:23 -0800)]
Merge tag 'trace-v4.4-rc3' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"During the merge window I added a new file that is used to filter
trace events on pids. It filters all events where only tasks with
their pid in that file exists. It also handles the sched_switch and
sched_wakeup trace events where the current task does not have its pid
in the file, but the task either being switched to or awaken does.
Unfortunately, I forgot about sched_wakeup_new and sched_waking. Both
of these tracepoints use the same class as the sched_wakeup
tracepoint, and they too should be included in what gets filtered by
the set_event_pid file"
* tag 'trace-v4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Add sched_wakeup_new and sched_waking tracepoints for pid filter
David S. Miller [Thu, 3 Dec 2015 20:56:22 +0000 (15:56 -0500)]
Merge tag 'mac80211-for-davem-2015-12-02' of git://git./linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A small set of fixes for 4.4:
* fix scanning in mac80211 to not actively scan radar
channels (from Antonio)
* fix uninitialized variable in remain-on-channel that
could lead to treating frame TX as remain-on-channel
and not sending the frame at all
* remove NL80211_FEATURE_FULL_AP_CLIENT_STATE again, it
was broken and needs more work, we'll enable it later
* fix call_rcu() induced use-after-reset/free in mesh
(that was suddenly causing issues in certain tests)
* always request block-ack window size 64 as we found
some APs will otherwise crash (really ...)
* fix P2P-Device teardown sequence to avoid restarting
with uninitialized data
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jérôme Pouiller [Thu, 3 Dec 2015 09:02:35 +0000 (10:02 +0100)]
net: phy: reset only targeted phy
It is possible to address another chip on same MDIO bus. The case is
correctly handled for media advertising. It is taken into account
only if mii_data->phy_id == phydev->addr. However, this condition
was missing for reset case.
Signed-off-by: Jérôme Pouiller <jezz@sysmic.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 3 Dec 2015 20:07:14 +0000 (15:07 -0500)]
Merge branch 'bnxt_en-fixes'
Michael Chan says:
====================
bnxt_en: set mac address and uc_list bug fixes.
Fix ndo_set_mac_address() for PF and VF.
Re-apply uc_list after chip reset.
v2: Fix compile error if CONFIG_BNXT_SRIOV is not set.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Wed, 2 Dec 2015 06:54:08 +0000 (01:54 -0500)]
bnxt_en: Setup uc_list mac filters after resetting the chip.
Call bnxt_cfg_rx_mode() in bnxt_init_chip() to setup uc_list and
mc_list mac address filters. Before the patch, uc_list is not
setup again after chip reset (such as ethtool ring size change)
and macvlans don't work any more after that.
Modify bnxt_cfg_rx_mode() to return error codes appropriately so
that the init chip sequence can detect any failures.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeffrey Huang [Wed, 2 Dec 2015 06:54:07 +0000 (01:54 -0500)]
bnxt_en: enforce proper storing of MAC address
For PF, the bp->pf.mac_addr always holds the permanent MAC
addr assigned by the HW. For VF, the bp->vf.mac_addr always
holds the administrator assigned VF MAC addr. The random
generated VF MAC addr should never get stored to bp->vf.mac_addr.
This way, when the VF wants to change the MAC address, we can tell
if the adminstrator has already set it and disallow the VF from
changing it.
v2: Fix compile error if CONFIG_BNXT_SRIOV is not set.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeffrey Huang [Wed, 2 Dec 2015 06:54:06 +0000 (01:54 -0500)]
bnxt_en: Fixed incorrect implementation of ndo_set_mac_address
The existing ndo_set_mac_address only copies the new MAC addr
and didn't set the new MAC addr to the HW. The correct way is
to delete the existing default MAC filter from HW and add
the new one. Because of RFS filters are also dependent on the
default mac filter l2 context, the driver must go thru
close_nic() to delete the default MAC and RFS filters, then
open_nic() to set the default MAC address to HW.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Zapolskiy [Wed, 2 Dec 2015 06:12:13 +0000 (08:12 +0200)]
net: lpc_eth: remove irq > NR_IRQS check from probe()
If the driver is used on an ARM platform with SPARSE_IRQ defined,
semantics of NR_IRQS is different (minimal value of virtual irqs) and
by default it is set to 16, see arch/arm/include/asm/irq.h.
This value may be less than the actual number of virtual irqs, which
may break the driver initialization. The check removal allows to use
the driver on such a platform, and, if irq controller driver works
correctly, the check is not needed on legacy platforms.
Fixes a runtime problem:
lpc-eth
31060000.ethernet: error getting resources.
lpc_eth: lpc-eth: not found (-6).
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 2 Dec 2015 04:08:51 +0000 (20:08 -0800)]
net_sched: fix qdisc_tree_decrease_qlen() races
qdisc_tree_decrease_qlen() suffers from two problems on multiqueue
devices.
One problem is that it updates sch->q.qlen and sch->qstats.drops
on the mq/mqprio root qdisc, while it should not : Daniele
reported underflows errors :
[ 681.774821] PAX: sch->q.qlen: 0 n: 1
[ 681.774825] PAX: size overflow detected in function qdisc_tree_decrease_qlen net/sched/sch_api.c:769 cicus.693_49 min, count: 72, decl: qlen; num: 0; context: sk_buff_head;
[ 681.774954] CPU: 2 PID: 19 Comm: ksoftirqd/2 Tainted: G O 4.2.6.
201511282239-1-grsec #1
[ 681.774955] Hardware name: ASUSTeK COMPUTER INC. X302LJ/X302LJ, BIOS X302LJ.202 03/05/2015
[ 681.774956]
ffffffffa9a04863 0000000000000000 0000000000000000 ffffffffa990ff7c
[ 681.774959]
ffffc90000d3bc38 ffffffffa95d2810 0000000000000007 ffffffffa991002b
[ 681.774960]
ffffc90000d3bc68 ffffffffa91a44f4 0000000000000001 0000000000000001
[ 681.774962] Call Trace:
[ 681.774967] [<
ffffffffa95d2810>] dump_stack+0x4c/0x7f
[ 681.774970] [<
ffffffffa91a44f4>] report_size_overflow+0x34/0x50
[ 681.774972] [<
ffffffffa94d17e2>] qdisc_tree_decrease_qlen+0x152/0x160
[ 681.774976] [<
ffffffffc02694b1>] fq_codel_dequeue+0x7b1/0x820 [sch_fq_codel]
[ 681.774978] [<
ffffffffc02680a0>] ? qdisc_peek_dequeued+0xa0/0xa0 [sch_fq_codel]
[ 681.774980] [<
ffffffffa94cd92d>] __qdisc_run+0x4d/0x1d0
[ 681.774983] [<
ffffffffa949b2b2>] net_tx_action+0xc2/0x160
[ 681.774985] [<
ffffffffa90664c1>] __do_softirq+0xf1/0x200
[ 681.774987] [<
ffffffffa90665ee>] run_ksoftirqd+0x1e/0x30
[ 681.774989] [<
ffffffffa90896b0>] smpboot_thread_fn+0x150/0x260
[ 681.774991] [<
ffffffffa9089560>] ? sort_range+0x40/0x40
[ 681.774992] [<
ffffffffa9085fe4>] kthread+0xe4/0x100
[ 681.774994] [<
ffffffffa9085f00>] ? kthread_worker_fn+0x170/0x170
[ 681.774995] [<
ffffffffa95d8d1e>] ret_from_fork+0x3e/0x70
mq/mqprio have their own ways to report qlen/drops by folding stats on
all their queues, with appropriate locking.
A second problem is that qdisc_tree_decrease_qlen() calls qdisc_lookup()
without proper locking : concurrent qdisc updates could corrupt the list
that qdisc_match_from_root() parses to find a qdisc given its handle.
Fix first problem adding a TCQ_F_NOPARENT qdisc flag that
qdisc_tree_decrease_qlen() can use to abort its tree traversal,
as soon as it meets a mq/mqprio qdisc children.
Second problem can be fixed by RCU protection.
Qdisc are already freed after RCU grace period, so qdisc_list_add() and
qdisc_list_del() simply have to use appropriate rcu list variants.
A future patch will add a per struct netdev_queue list anchor, so that
qdisc_tree_decrease_qlen() can have more efficient lookups.
Reported-by: Daniele Fucini <dfucini@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Cong Wang <cwang@twopensource.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Tue, 1 Dec 2015 17:33:36 +0000 (18:33 +0100)]
openvswitch: fix hangup on vxlan/gre/geneve device deletion
Each openvswitch tunnel vport (vxlan,gre,geneve) holds a reference
to the underlying tunnel device, but never released it when such
device is deleted.
Deleting the underlying device via the ip tool cause the kernel to
hangup in the netdev_wait_allrefs() loop.
This commit ensure that on device unregistration dp_detach_port_notify()
is called for all vports that hold the device reference, properly
releasing it.
Fixes: 614732eaa12d ("openvswitch: Use regular VXLAN net_device device")
Fixes: b2acd1dc3949 ("openvswitch: Use regular GRE net_device instead of vport")
Fixes: 6b001e682e90 ("openvswitch: Use Geneve device.")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Flavio Leitner <fbl@sysclose.org>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
James Bottomley [Thu, 3 Dec 2015 17:32:33 +0000 (09:32 -0800)]
Merge branch 'mkp-fixes' into fixes
James Bottomley [Wed, 2 Dec 2015 21:36:58 +0000 (13:36 -0800)]
mpt3sas: fix Kconfig dependency problem for mpt2sas back compatibility
The non-PCI builds of the O day test project are failing:
On Thu, 2015-12-03 at 05:02 +0800, kbuild test robot wrote:
> warning: (SCSI_MPT2SAS) selects SCSI_MPT3SAS which has unmet direct
> dependencies (SCSI_LOWLEVEL && PCI && SCSI)
The problem is that select and depend don't interact because Kconfig doesn't
have a SAT solver, so depend picks up dependencies and select does onward
selects, but select doesn't pick up dependencies. To fix this, we need to add
the correct dependencies to the MPT2SAS option like this.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: b840c3627b6f4f856b333a14a72f8ed86da2f86c
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
projects / openwrt / staging / blogic.git / log