Rafael J. Wysocki [Thu, 30 Aug 2018 23:23:31 +0000 (01:23 +0200)]
Merge branch 'pm-core'
Merge a generic clock management fix for 4.19-rc2.
* pm-core:
PM / clk: signedness bug in of_pm_clk_add_clks()
Rafael J. Wysocki [Tue, 21 Aug 2018 08:44:10 +0000 (10:44 +0200)]
cpuidle: menu: Retain tick when shallow state is selected
The case addressed by commit
5ef499cd571c (cpuidle: menu: Handle
stopped tick more aggressively) in the stopped tick case is present
when the tick has not been stopped yet too. Namely, if only two CPU
idle states, shallow state A with target residency significantly
below the tick boundary and deep state B with target residency
significantly above it, are available and the predicted idle
duration is above the tick boundary, but below the target residency
of state B, state A will be selected and the CPU may spend indefinite
amount of time in it, which is not quite energy-efficient.
However, if the tick has not been stopped yet and the governor is
about to select a shallow idle state for the CPU even though the idle
duration predicted by it is above the tick boundary, it should be
fine to wake up the CPU early, so the tick can be retained then and
the governor will have a chance to select a deeper state when it runs
next time.
[Note that when this really happens, it will make the idle duration
predictor believe that the CPU might be idle longer than predicted,
which will make it more likely to predict longer idle durations going
forward, but that will also cause deeper idle states to be selected
going forward, on average, which is what's needed here.]
Fixes: 87c9fe6ee495 (cpuidle: menu: Avoid selecting shallow states with stopped tick)
Reported-by: Leo Yan <leo.yan@linaro.org>
Cc: 4.17+ <stable@vger.kernel.org> # 4.17+: 5ef499cd571c (cpuidle: menu: Handle ...)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Dan Carpenter [Thu, 23 Aug 2018 13:59:25 +0000 (16:59 +0300)]
PM / clk: signedness bug in of_pm_clk_add_clks()
"count" needs to be signed for the error handling to work. I made "i"
signed as well so they match.
Fixes: 02113ba93ea4 (PM / clk: Add support for obtaining clocks from device-tree)
Cc: 4.6+ <stable@vger.kernel.org> # 4.6+
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Wed, 22 Aug 2018 14:42:36 +0000 (07:42 -0700)]
Merge tag 'pm-4.19-rc1-2' of git://git./linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These fix the main idle loop and the menu cpuidle governor, clean up
the latter, fix a mistake in the PCI bus type's support for system
suspend and resume, fix the ondemand and conservative cpufreq
governors, address a build issue in the system wakeup framework and
make the ACPI C-states desciptions less confusing.
Specifics:
- Make the idle loop handle stopped scheduler tick correctly (Rafael
Wysocki).
- Prevent the menu cpuidle governor from letting CPUs spend too much
time in shallow idle states when it is invoked with scheduler tick
stopped and clean it up somewhat (Rafael Wysocki).
- Avoid invoking the platform firmware to make the platform enter the
ACPI S3 sleep state with suspended PCIe root ports which may
confuse the firmware and cause it to crash (Rafael Wysocki).
- Fix sysfs-related race in the ondemand and conservative cpufreq
governors which may cause the system to crash if the governor
module is removed during an update of CPU frequency limits (Henry
Willard).
- Select SRCU when building the system wakeup framework to avoid a
build issue in it (zhangyi).
- Make the descriptions of ACPI C-states vendor-neutral to avoid
confusion (Prarit Bhargava)"
* tag 'pm-4.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: menu: Handle stopped tick more aggressively
sched: idle: Avoid retaining the tick when it has been stopped
PCI / ACPI / PM: Resume all bridges on suspend-to-RAM
cpuidle: menu: Update stale polling override comment
cpufreq: governor: Avoid accessing invalid governor_data
x86/ACPI/cstate: Make APCI C1 FFH MWAIT C-state description vendor-neutral
cpuidle: menu: Fix white space
PM / sleep: wakeup: Fix build error caused by missing SRCU support
Linus Torvalds [Wed, 22 Aug 2018 14:40:33 +0000 (07:40 -0700)]
Merge git://git./linux/kernel/git/davem/ide
Pull IDE updates from David Miller:
- Remove redundant variables (Colin Ian King)
- Expected switch fall-through annotations (Gustavo A. R. Silva)
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide:
ide: mark expected switch fall-throughs
ide-tape: remove redundant variable buffer_size
ide: remove redundant variables queue_run_ms and left
Linus Torvalds [Wed, 22 Aug 2018 14:38:21 +0000 (07:38 -0700)]
Merge git://git./linux/kernel/git/davem/sparc
Pull sparc updates from David Miller:
"Nothing super serious:
- Convert sparc32 over to NO_BOOTMEM (Mike Rapoport)
- Use dma_noncoherent_ops on sparc32 (Christoph Hellwig)
- Fix kbuild defconfig handling on sparc32 (Masahiro Yamada)"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: fix KBUILD_DEFCONFIG for ARCH=sparc32
sparc32: split ramdisk detection and reservation to a helper function
sparc32: switch to NO_BOOTMEM
sparc: mm/init_32: kill trailing whitespace
sparc: use generic dma_noncoherent_ops
Linus Torvalds [Wed, 22 Aug 2018 13:24:26 +0000 (06:24 -0700)]
Merge tag 'for-4.19' of git://git.sourceforge.jp/gitroot/uclinux-h8/linux
Pull arch/h8300 updates from Yoshinori Sato.
* tag 'for-4.19' of git://git.sourceforge.jp/gitroot/uclinux-h8/linux:
h8300: fix IRQ no
arch/h8300: add a defconfig target
arch/h8300: eliminate kgbd.c warning
arch/h8300: eliminate ptrace.h warnings
h8300:let the checker know that size_t is ulong
h8300: Don't include linux/kernel.h in asm/atomic.h
h8300: remove unnecessary of_platform_populate call
h8300: Correct signature of test_bit()
h8300: irqchip: fix warning
h8300: switch to NO_BOOTMEM
h8300: gcc-8.1 fix
h8300: Add missing output register.
Yoshinori Sato [Wed, 11 Jul 2018 09:39:09 +0000 (18:39 +0900)]
h8300: fix IRQ no
Old timer handler use 24 (Compare match A).
But current timer handler use 26 (Overflow).
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Randy Dunlap [Thu, 19 Jul 2018 06:04:29 +0000 (23:04 -0700)]
arch/h8300: add a defconfig target
Make the "defconfig" target valid for arch/h8300. Currently
"make ARCH=h8300 defconfig" produces:
*** Can't find default configuration "arch/h8300/defconfig"!
../scripts/kconfig/Makefile:87: recipe for target 'defconfig' failed
By adding a value for KBUILD_DEFCONFIG, "make ARCH=h8300 defconfig"
successfully produces a kernel .config file:
*** Default configuration is based on 'edosk2674_defconfig'
This is useful for Kconfig editing/testing.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: uclinux-h8-devel@lists.sourceforge.jp (moderated for non-subscribers)
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Randy Dunlap [Fri, 20 Jul 2018 02:36:06 +0000 (19:36 -0700)]
arch/h8300: eliminate kgbd.c warning
Drop the "const" qualifier from arch_kgdb_ops to eliminate the gcc
warning (gcc version is 8.1.0).
arch/h8300/kernel/kgdb.c:132:24: error: conflicting type qualifiers for 'arch_kgdb_ops'
const struct kgdb_arch arch_kgdb_ops = {
In file included from ../arch/h8300/kernel/kgdb.c:12:
../include/linux/kgdb.h:284:26: note: previous declaration of 'arch_kgdb_ops' was here
extern struct kgdb_arch arch_kgdb_ops;
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: uclinux-h8-devel@lists.sourceforge.jp
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Randy Dunlap [Fri, 20 Jul 2018 02:34:53 +0000 (19:34 -0700)]
arch/h8300: eliminate ptrace.h warnings
Add a "struct task_struct;" stub to arch/h8300's ptrace.h header to
eliminate gcc warnings (gcc version is 8.1.0).
../arch/h8300/include/asm/ptrace.h:32:34: warning: 'struct task_struct' declared inside parameter list will not be visible outside of this definition or declaration
extern long h8300_get_reg(struct task_struct *task, int regno);
../arch/h8300/include/asm/ptrace.h:33:33: warning: 'struct task_struct' declared inside parameter list will not be visible outside of this definition or declaration
extern int h8300_put_reg(struct task_struct *task, int regno,
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: uclinux-h8-devel@lists.sourceforge.jp
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Luc Van Oostenryck [Wed, 30 May 2018 21:03:43 +0000 (23:03 +0200)]
h8300:let the checker know that size_t is ulong
All 64bit archs use unsigned long for size_t and most 32bit
archs use 'unsigned int'. By default, this is what is assumed
by sparse.
However, on h8300 (a 32bit arch) size_t is unsigned long which
can led sparse to emit wrong warnings.
Fix this by passing to sparse the flag -msize-long, telling it
that size_t is unsigned long.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Will Deacon [Fri, 1 Jun 2018 16:06:21 +0000 (17:06 +0100)]
h8300: Don't include linux/kernel.h in asm/atomic.h
linux/kernel.h isn't needed by asm/atomic.h and will result in circular
dependencies when the asm-generic atomic bitops are built around the
tomic_long_t interface.
Remove the broad include and replace it with linux/compiler.h for
READ_ONCE etc and asm/irqflags.h for arch_local_irq_save etc.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Rob Herring [Tue, 19 Jun 2018 21:40:54 +0000 (15:40 -0600)]
h8300: remove unnecessary of_platform_populate call
The DT core will call of_platform_populate, so it is not necessary for
arch specific code to call it unless there are custom match entries,
auxdata or parent device. Neither of those apply here, so remove the call.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: uclinux-h8-devel@lists.sourceforge.jp
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Geert Uytterhoeven [Thu, 21 Jun 2018 19:24:44 +0000 (21:24 +0200)]
h8300: Correct signature of test_bit()
mm/filemap.c: In function 'clear_bit_unlock_is_negative_byte':
mm/filemap.c:1181:30: warning: passing argument 2 of 'test_bit' discards 'volatile' qualifier from pointer target type [-Wdiscarded-qualifiers]
return test_bit(PG_waiters, mem);
^~~
In file included from include/linux/bitops.h:38,
from include/linux/kernel.h:11,
from include/linux/list.h:9,
from include/linux/wait.h:7,
from include/linux/wait_bit.h:8,
from include/linux/fs.h:6,
from include/linux/dax.h:5,
from mm/filemap.c:14:
arch/h8300/include/asm/bitops.h:69:57: note: expected 'const long unsigned int *' but argument is of type 'volatile void *'
static inline int test_bit(int nr, const unsigned long *addr)
~~~~~~~~~~~~~~~~~~~~~^~~~
Make the bitmask pointed to by the "addr" parameter volatile to fix
this, like is done on other architectures.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Yoshinori Sato [Mon, 13 Aug 2018 01:07:46 +0000 (10:07 +0900)]
h8300: irqchip: fix warning
Var "addr" type incorrect.
It have interrupt controler register address.
Type of void __iomem is correct.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Rob Herring [Fri, 16 Mar 2018 21:33:06 +0000 (16:33 -0500)]
h8300: switch to NO_BOOTMEM
Commit
0fa1c579349f ("of/fdt: use memblock_virt_alloc for early alloc")
inadvertently switched the DT unflattening allocations from memblock to
bootmem which doesn't work because the unflattening happens before
bootmem is initialized. Swapping the order of bootmem init and
unflattening could also fix this, but removing bootmem is desired. So
enable NO_BOOTMEM on h8300 like other architectures have done.
Fixes: 0fa1c579349f ("of/fdt: use memblock_virt_alloc for early alloc")
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: uclinux-h8-devel@lists.sourceforge.jp
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Yoshinori Sato [Fri, 13 Jul 2018 07:36:21 +0000 (16:36 +0900)]
h8300: gcc-8.1 fix
Since gcc 8.1 does not generate an assignment statement to er 0,
we had to explicitly write it.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Yoshinori Sato [Thu, 12 Jul 2018 14:31:45 +0000 (23:31 +0900)]
h8300: Add missing output register.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Linus Torvalds [Wed, 22 Aug 2018 01:47:36 +0000 (18:47 -0700)]
Merge tag 'fuse-update-4.19' of git://git./linux/kernel/git/mszeredi/fuse
Pull fuse update from Miklos Szeredi:
"Various bug fixes and cleanups"
* tag 'fuse-update-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: reduce allocation size for splice_write
fuse: use kvmalloc to allocate array of pipe_buffer structs.
fuse: convert last timespec use to timespec64
fs: fuse: Adding new return type vm_fault_t
fuse: simplify fuse_abort_conn()
fuse: Add missed unlock_page() to fuse_readpages_fill()
fuse: Don't access pipe->buffers without pipe_lock()
fuse: fix initial parallel dirops
fuse: Fix oops at process_init_reply()
fuse: umount should wait for all requests
fuse: fix unlocked access to processing queue
fuse: fix double request_end()
Linus Torvalds [Wed, 22 Aug 2018 01:19:09 +0000 (18:19 -0700)]
Merge tag 'ovl-update-4.19' of git://git./linux/kernel/git/mszeredi/vfs
Pull overlayfs updates from Miklos Szeredi:
"This contains two new features:
- Stack file operations: this allows removal of several hacks from
the VFS, proper interaction of read-only open files with copy-up,
possibility to implement fs modifying ioctls properly, and others.
- Metadata only copy-up: when file is on lower layer and only
metadata is modified (except size) then only copy up the metadata
and continue to use the data from the lower file"
* tag 'ovl-update-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs: (66 commits)
ovl: Enable metadata only feature
ovl: Do not do metacopy only for ioctl modifying file attr
ovl: Do not do metadata only copy-up for truncate operation
ovl: add helper to force data copy-up
ovl: Check redirect on index as well
ovl: Set redirect on upper inode when it is linked
ovl: Set redirect on metacopy files upon rename
ovl: Do not set dentry type ORIGIN for broken hardlinks
ovl: Add an inode flag OVL_CONST_INO
ovl: Treat metacopy dentries as type OVL_PATH_MERGE
ovl: Check redirects for metacopy files
ovl: Move some dir related ovl_lookup_single() code in else block
ovl: Do not expose metacopy only dentry from d_real()
ovl: Open file with data except for the case of fsync
ovl: Add helper ovl_inode_realdata()
ovl: Store lower data inode in ovl_inode
ovl: Fix ovl_getattr() to get number of blocks from lower
ovl: Add helper ovl_dentry_lowerdata() to get lower data dentry
ovl: Copy up meta inode data from lowest data inode
ovl: Modify ovl_lookup() and friends to lookup metacopy dentry
...
Linus Torvalds [Wed, 22 Aug 2018 01:15:47 +0000 (18:15 -0700)]
Merge tag 'xfs-4.19-merge-7' of git://git./fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
- Fix an uninitialized variable
- Don't use obviously garbage AG header counters to calculate
transaction reservations
- Trigger icount recalculation on bad icount when mounting
* tag 'xfs-4.19-merge-7' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
iomap: fix WARN_ON_ONCE on uninitialized variable
xfs: sanity check ag header values in xrep_calc_ag_resblks
xfs: recalculate summary counters at mount time if icount is bad
Linus Torvalds [Wed, 22 Aug 2018 01:06:27 +0000 (18:06 -0700)]
Merge tag 'for-v4.19' of git://git./linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
- Improve support for TI bq20z75 in sbs-battery
- Add Qualcomm PM8xxx reboot driver
- Add cros-ec USBPD charger driver
- Move ds2760 battery driver from w1 to power-supply and add DT support
- Misc fixes
* tag 'for-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (28 commits)
power: supply: bq27xxx: Update comments
power: supply: max77693_charger: fix unintentional fall-through
power: supply: mark expected switch fall-throughs
power: supply: lego_ev3_battery: fix Vce offset
power: supply: lego_ev3_battery: Don't ignore iio_read_channel_processed() return value
power: supply: ds2760_battery: add devicetree probing
power: supply: ds2760_battery: merge ds2760 supply driver with its w1 slave companion
w1: core: match sub-nodes of bus masters in devicetree
dt-bindings: w1: document bindings for ds2760 battery monitor
dt-bindings: w1: document generic onewire bindings
power: supply: adp5061: Fix a couple off by ones
dt-bindings: power: reset: qcom: Add resin binding
adp5061: New driver for ADP5061 I2C battery charger
power: generic-adc-battery: check for duplicate properties copied from iio channels
power: generic-adc-battery: fix out-of-bounds write when copying channel properties
power: supply: axp288_charger: Fix initial constant_charge_current value
power: supply: ab8500: stop using getnstimeofday64()
power: gemini-poweroff: Avoid more spurious poweroffs
power: vexpress: fix corruption in notifier registration
power: remove possible deadlock when unregistering power_supply
...
Linus Torvalds [Wed, 22 Aug 2018 00:40:46 +0000 (17:40 -0700)]
Merge branch 'i2c/for-4.19' of git://git./linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
- the core has now a lockless variant of i2c_smbus_xfer. Some open
coded versions of this got removed in drivers. This also enables
proper SCCB support in regmap.
- locking got a more precise naming. i2c_{un}lock_adapter() had to go,
and we know use i2c_lock_bus() consistently with flags like
I2C_LOCK_ROOT_ADAPTER and I2C_LOCK_SEGMENT to avoid ambiguity.
- the gpio fault injector got a new delicate testcase
- the bus recovery procedure got fixed to handle the new testcase
correctly
- a new quirk flag for controllers not able to handle zero length
messages together with driver updates to use it
- new drivers: FSI bus attached I2C masters, GENI I2C controller, Owl
family S900
- and a good set of driver improvements and bugfixes
* 'i2c/for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (77 commits)
i2c: rcar: implement STOP and REP_START according to docs
i2c: rcar: refactor private flags
i2c: core: ACPI: Make acpi_gsb_i2c_read_bytes() check i2c_transfer return value
i2c: core: ACPI: Properly set status byte to 0 for multi-byte writes
dt-bindings: i2c: rcar: Add r8a774a1 support
dt-bindings: i2c: sh_mobile: Add r8a774a1 support
i2c: imx: Simplify stopped state tracking
i2c: imx: Fix race condition in dma read
i2c: pasemi: remove hardcoded bus numbers on smbus
i2c: designware: Add SPDX license tag
i2c: designware: Convert to use struct i2c_timings
i2c: core: Parse SDA hold time from firmware
i2c: designware-pcidrv: Mark expected switch fall-through
i2c: amd8111: Mark expected switch fall-through
i2c: sh_mobile: use core to detect 'no zero length read' quirk
i2c: xlr: use core to detect 'no zero length' quirk
i2c: rcar: use core to detect 'no zero length' quirk
i2c: stu300: use core to detect 'no zero length' quirk
i2c: pmcmsp: use core to detect 'no zero length' quirk
i2c: mxs: use core to detect 'no zero length' quirk
...
Linus Torvalds [Tue, 21 Aug 2018 20:47:29 +0000 (13:47 -0700)]
Merge branch 'siginfo-linus' of git://git./linux/kernel/git/ebiederm/user-namespace
Pull core signal handling updates from Eric Biederman:
"It was observed that a periodic timer in combination with a
sufficiently expensive fork could prevent fork from every completing.
This contains the changes to remove the need for that restart.
This set of changes is split into several parts:
- The first part makes PIDTYPE_TGID a proper pid type instead
something only for very special cases. The part starts using
PIDTYPE_TGID enough so that in __send_signal where signals are
actually delivered we know if the signal is being sent to a a group
of processes or just a single process.
- With that prep work out of the way the logic in fork is modified so
that fork logically makes signals received while it is running
appear to be received after the fork completes"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (22 commits)
signal: Don't send signals to tasks that don't exist
signal: Don't restart fork when signals come in.
fork: Have new threads join on-going signal group stops
fork: Skip setting TIF_SIGPENDING in ptrace_init_task
signal: Add calculate_sigpending()
fork: Unconditionally exit if a fatal signal is pending
fork: Move and describe why the code examines PIDNS_ADDING
signal: Push pid type down into complete_signal.
signal: Push pid type down into __send_signal
signal: Push pid type down into send_signal
signal: Pass pid type into do_send_sig_info
signal: Pass pid type into send_sigio_to_task & send_sigurg_to_task
signal: Pass pid type into group_send_sig_info
signal: Pass pid and pid type into send_sigqueue
posix-timers: Noralize good_sigevent
signal: Use PIDTYPE_TGID to clearly store where file signals will be sent
pid: Implement PIDTYPE_TGID
pids: Move the pgrp and session pid pointers from task_struct to signal_struct
kvm: Don't open code task_pid in kvm_vcpu_ioctl
pids: Compute task_tgid using signal->leader_pid
...
Rafael J. Wysocki [Tue, 21 Aug 2018 20:39:24 +0000 (22:39 +0200)]
Merge branches 'pm-cpufreq', 'pm-pci' and 'pm-sleep'
Merge fixes for the ondemand and conservative cpufreq governors,
PCI power management and system wakeup framework.
* pm-cpufreq:
cpufreq: governor: Avoid accessing invalid governor_data
* pm-pci:
PCI / ACPI / PM: Resume all bridges on suspend-to-RAM
* pm-sleep:
PM / sleep: wakeup: Fix build error caused by missing SRCU support
Linus Torvalds [Tue, 21 Aug 2018 20:33:33 +0000 (13:33 -0700)]
Merge tag 'chrome-platform-for-linus-4.19' of git://git./linux/kernel/git/bleung/chrome-platform
Pull chrome platform updates from Benson Leung.
Everything but the SPDX identifier updates actually came in earlier
through the MFD merge.
* tag 'chrome-platform-for-linus-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform:
platform/chrome: chromeos_tbmc - fix SPDX identifier
Linus Torvalds [Tue, 21 Aug 2018 20:18:22 +0000 (13:18 -0700)]
Merge tag 'microblaze-v4.19-rc1' of git://git.monstr.eu/linux-2.6-microblaze
Pull arch/microblaze updates from Michal Simek:
- use generic noncoherent direct mapping
- use LDFLAGS instead of LD
- pci error path fix
- remove incorrect comments
* tag 'microblaze-v4.19-rc1' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze/PCI: Remove stale pcibios_align_resource() comment
microblaze: delete wrong comment about machine_early_init
microblaze: add endianness options to LDFLAGS instead of LD
microblaze: remove consistent_sync and consistent_sync_page
microblaze: use generic dma_noncoherent_ops
microblaze: warn if of_iomap() failed
Masahiro Yamada [Mon, 20 Aug 2018 17:08:28 +0000 (02:08 +0900)]
sparc: fix KBUILD_DEFCONFIG for ARCH=sparc32
As commit
5ba800962a80 ("kbuild: update ARCH alias info for sparc")
addressed, SPARC accepts ARCH=sparc32 as an alias.
However, arch/sparc/Makefile wrongly sets KBUILD_DEFCONFIG, then
sparc64_defconfig is chosen as the base configuration for ARCH=sparc32.
$ make ARCH=sparc32 defconfig
*** Default configuration is based on 'sparc64_defconfig'
#
# configuration written to .config
#
Fix the logic to choose sparc64_defconfig only when ARCH=sparc64.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 21 Aug 2018 19:40:26 +0000 (12:40 -0700)]
Merge branch 'sparc32-NO_BOOTMEM'
Mike Rapoport says:
====================
sparc32: switch to NO_BOOTMEM
These patches convert sparc32 to use memblock + nobootmem.
I've made the conversion as simple as possible, just enough to allow moving
HAVE_MEMBLOCK and NO_BOOTMEM to the common SPARC configuration.
v2 changes:
* split whitespace changes to a separate patch
* address Sam's comments [1]
[1] https://lkml.org/lkml/2018/8/2/403
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Rapoport [Mon, 6 Aug 2018 10:52:35 +0000 (13:52 +0300)]
sparc32: split ramdisk detection and reservation to a helper function
The detection and reservation of ramdisk memory were separated to allow
bootmem bitmap initialization after the ramdisk boundaries are detected.
Since the bootmem initialization is removed, the reservation of ramdisk
memory is done immediately after its boundaries are found.
Split the entire block into a separate helper function.
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Rapoport [Mon, 6 Aug 2018 10:52:34 +0000 (13:52 +0300)]
sparc32: switch to NO_BOOTMEM
Each populated sparc_phys_bank is added to memblock.memory. The
reserve_bootmem() calls are replaced with memblock_reserve(), and the
bootmem bitmap initialization is droppped.
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Rapoport [Mon, 6 Aug 2018 10:52:33 +0000 (13:52 +0300)]
sparc: mm/init_32: kill trailing whitespace
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christoph Hellwig [Tue, 31 Jul 2018 08:02:04 +0000 (10:02 +0200)]
sparc: use generic dma_noncoherent_ops
Switch to the generic noncoherent direct mapping implementation.
This removes the previous sync_single_for_device implementation, which
looks bogus given that no syncing is happening in the similar but more
important map_single case.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lorenzo Pieralisi [Mon, 20 Aug 2018 09:47:29 +0000 (10:47 +0100)]
microblaze/PCI: Remove stale pcibios_align_resource() comment
commit
01cf9d524ff0 ("microblaze/PCI: Support generic Xilinx AXI PCIe Host
Bridge IP driver")
and
commit
ecf677c8dcaa ("PCI: Add a generic weak pcibios_align_resource()")
first patched then removed pcibios_align_resource() from the microblaze
architecture code but failed to remove the comment that was added to
it.
Remove it since it has now become stale and it is quite confusing.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bharat Kumar Gogada <bharatku@xilinx.com>
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Linus Torvalds [Tue, 21 Aug 2018 02:37:09 +0000 (19:37 -0700)]
Merge tag 'please-pull-noboot' of git://git./linux/kernel/git/aegl/linux
Pull ia64 NO_BOOTMEM conversion from Tony Luck:
"Mike Rapoport kindly fixed up ia64 to work with NO_BOOTMEM"
* tag 'please-pull-noboot' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
ia64: switch to NO_BOOTMEM
ia64: use mem_data to detect nodes' minimal and maximal PFNs
ia64: remove unused num_dma_physpages member from 'struct early_node_data'
ia64: contig/paging_init: reduce code duplication
Linus Torvalds [Tue, 21 Aug 2018 02:02:17 +0000 (19:02 -0700)]
Merge tag 'linux-kselftest-4.19-rc1' of git://git./linux/kernel/git/shuah/linux-kselftest
Pull Kselftest update from Shuah Khan:
- add cgroup core selftests
- fix compile warnings in android ion test
- fix to bugs in exclude and skip paths in vDSO test
- remove obsolete config options
- add missing .gitignore file
* tag 'linux-kselftest-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/ftrace: Fix kprobe string testcase to not probe notrace function
selftests: mount: remove no longer needed config option
selftests: cgroup: add gitignore file
Add cgroup core selftests
selftests: vDSO - fix to return KSFT_SKIP when test couldn't be run
selftests: vDSO - fix to exclude x86 test on non-x86 platforms
selftests/android: initialize heap_type to avoid compiling warning
Linus Torvalds [Tue, 21 Aug 2018 01:32:00 +0000 (18:32 -0700)]
Merge tag 'trace-v4.19' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
- Restructure of lockdep and latency tracers
This is the biggest change. Joel Fernandes restructured the hooks
from irqs and preemption disabling and enabling. He got rid of a lot
of the preprocessor #ifdef mess that they caused.
He turned both lockdep and the latency tracers to use trace events
inserted in the preempt/irqs disabling paths. But unfortunately,
these started to cause issues in corner cases. Thus, parts of the
code was reverted back to where lockdep and the latency tracers just
get called directly (without using the trace events). But because the
original change cleaned up the code very nicely we kept that, as well
as the trace events for preempt and irqs disabling, but they are
limited to not being called in NMIs.
- Have trace events use SRCU for "rcu idle" calls. This was required
for the preempt/irqs off trace events. But it also had to not allow
them to be called in NMI context. Waiting till Paul makes an NMI safe
SRCU API.
- New notrace SRCU API to allow trace events to use SRCU.
- Addition of mcount-nop option support
- SPDX headers replacing GPL templates.
- Various other fixes and clean ups.
- Some fixes are marked for stable, but were not fully tested before
the merge window opened.
* tag 'trace-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (44 commits)
tracing: Fix SPDX format headers to use C++ style comments
tracing: Add SPDX License format tags to tracing files
tracing: Add SPDX License format to bpf_trace.c
blktrace: Add SPDX License format header
s390/ftrace: Add -mfentry and -mnop-mcount support
tracing: Add -mcount-nop option support
tracing: Avoid calling cc-option -mrecord-mcount for every Makefile
tracing: Handle CC_FLAGS_FTRACE more accurately
Uprobe: Additional argument arch_uprobe to uprobe_write_opcode()
Uprobes: Simplify uprobe_register() body
tracepoints: Free early tracepoints after RCU is initialized
uprobes: Use synchronize_rcu() not synchronize_sched()
tracing: Fix synchronizing to event changes with tracepoint_synchronize_unregister()
ftrace: Remove unused pointer ftrace_swapper_pid
tracing: More reverting of "tracing: Centralize preemptirq tracepoints and unify their usage"
tracing/irqsoff: Handle preempt_count for different configs
tracing: Partial revert of "tracing: Centralize preemptirq tracepoints and unify their usage"
tracing: irqsoff: Account for additional preempt_disable
trace: Use rcu_dereference_raw for hooks from trace-event subsystem
tracing/kprobes: Fix within_notrace_func() to check only notrace functions
...
Linus Torvalds [Tue, 21 Aug 2018 01:26:55 +0000 (18:26 -0700)]
Merge tag 'ceph-for-4.19-rc1' of git://github.com/ceph/ceph-client
Pull ceph updates from Ilya Dryomov:
"The main things are support for cephx v2 authentication protocol and
basic support for rbd images within namespaces (myself).
Also included are y2038 conversion patches from Arnd, a pile of
miscellaneous fixes from Chengguang and Zheng's feature bit
infrastructure for the filesystem"
* tag 'ceph-for-4.19-rc1' of git://github.com/ceph/ceph-client: (40 commits)
ceph: don't drop message if it contains more data than expected
ceph: support cephfs' own feature bits
crush: fix using plain integer as NULL warning
libceph: remove unnecessary non NULL check for request_key
ceph: refactor error handling code in ceph_reserve_caps()
ceph: refactor ceph_unreserve_caps()
ceph: change to void return type for __do_request()
ceph: compare fsc->max_file_size and inode->i_size for max file size limit
ceph: add additional size check in ceph_setattr()
ceph: add additional offset check in ceph_write_iter()
ceph: add additional range check in ceph_fallocate()
ceph: add new field max_file_size in ceph_fs_client
libceph: weaken sizeof check in ceph_x_verify_authorizer_reply()
libceph: check authorizer reply/challenge length before reading
libceph: implement CEPHX_V2 calculation mode
libceph: add authorizer challenge
libceph: factor out encrypt_authorizer()
libceph: factor out __ceph_x_decrypt()
libceph: factor out __prepare_write_connect()
libceph: store ceph_auth_handshake pointer in ceph_connection
...
Linus Torvalds [Mon, 20 Aug 2018 23:30:27 +0000 (16:30 -0700)]
Merge tag 'rtc-4.19' of git://git./linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"It is now possible to add custom sysfs attributes while avoiding a
possible race condition. Unused code has been removed resulting in a
nice reduction of the code base. And more drivers have been switched
to SPDX by their maintainers.
Summary:
Subsystem:
- new helpers to add custom sysfs attributes
- struct rtc_task removal along with rtc_irq_[un]register()
- rtc_irq_set_state and rtc_irq_set_freq are not exported anymore
Drivers:
- armada38x: reset after rtc power loss
- ds1307: now supports m41t11
- isl1208: now supports isl1219 and tamper detection
- pcf2127: internal SRAM support"
* tag 'rtc-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (34 commits)
rtc: ds1307: simplify hwmon config
rtc: s5m: Add SPDX license identifier
rtc: maxim: Add SPDX license identifiers
rtc: isl1219: add device tree documentation
rtc: isl1208: set ev-evienb bit from device tree
rtc: isl1208: Add "evdet" interrupt source for isl1219
rtc: isl1208: add support for isl1219 with tamper detection
rtc: sysfs: facilitate attribute add to rtc device
rtc: remove struct rtc_task
char: rtc: remove task handling
rtc: pcf85063: preserve control register value between stop and start
rtc: sh: remove unused variable rtc_dev
rtc: unexport rtc_irq_set_*
rtc: simplify rtc_irq_set_state/rtc_irq_set_freq
rtc: remove irq_task and irq_task_lock
rtc: remove rtc_irq_register/rtc_irq_unregister
rtc: sh: remove dead code
rtc: sa1100: don't set PIE frequency
rtc: ds1307: support m41t11 variant
rtc: ds1307: fix data pointer to m41t0
...
Linus Torvalds [Mon, 20 Aug 2018 23:10:47 +0000 (16:10 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/livepatching
Pull livepatching updates from Jiri Kosina:
"Code cleanups from Kamalesh Babulal"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
livepatch: Validate module/old func name length
livepatch: Remove reliable stacktrace check in klp_try_switch_task()
Linus Torvalds [Mon, 20 Aug 2018 22:59:01 +0000 (15:59 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/hid
Pull HID updates from Jiri Kosina:
- touch_max detection improvements and quirk handling fixes in wacom
driver from Jason Gerecke and Ping Cheng
- Palm rejection from Dmitry Torokhov and _dial support from Benjamin
Tissoires for hid-multitouch driver
- Low voltage support for i2c-hid driver from Stephen Boyd
- Guitar-Hero support from Nicolas Adenis-Lamarre
- other assorted small fixes and device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (40 commits)
HID: intel_ish-hid: tx_buf memory leak on probe/remove
HID: intel-ish-hid: Prevent loading of driver on Mehlow
HID: cougar: Add support for the Cougar 500k Gaming Keyboard
HID: cougar: make compare_device_paths reusable
HID: intel-ish-hid: remove redundant variable num_frags
HID: multitouch: handle palm for touchscreens
HID: multitouch: touchscreens also use confidence reports
HID: multitouch: report MT_TOOL_PALM for non-confident touches
HID: microsoft: support the Surface Dial
HID: core: do not upper bound the collection stack
HID: input: enable Totem on the Dell Canvas 27
HID: multitouch: remove one copy of values
HID: multitouch: ditch mt_report_id
HID: multitouch: store a per application quirks value
HID: multitouch: Store per collection multitouch data
HID: multitouch: make sure the static list of class is not changed
input: add MT_TOOL_DIAL
HID: elan: Add support for touchpad on the Toshiba Click Mini L9W
HID: elan: Add USB-id for HP x2 10-n000nd touchpad
HID: elan: Add a flag for selecting if the touchpad has a LED
...
Linus Torvalds [Mon, 20 Aug 2018 22:41:37 +0000 (15:41 -0700)]
Merge tag 'backlight-next-4.19' of git://git./linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
"Core Framework:
- Remove unused/obsolete code/comments
New Functionality:
- Allow less granular brightness specification for high-res PWMs; pwm_bl
- Align brightness {inc,dec}rements with that perceived by the human-eye; pwm_bl
Fix-ups:
- Prepare for the introduction of -Wimplicit-fall-through; adp8860_bl
Bug Fixes:
- Fix uninitialised variable; pwm_bl"
* tag 'backlight-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: pwm_bl: Fix uninitialized variable
backlight: adp8860: Mark expected switch fall-through
backlight: Remove obsolete comment for ->state
dt-bindings: pwm-backlight: Move brightness-levels to optional
backlight: pwm_bl: Compute brightness of LED linearly to human eye
dt-bindings: pwm-backlight: Add a num-interpolation-steps property
backlight: pwm_bl: Linear interpolation between brightness-levels
Linus Torvalds [Mon, 20 Aug 2018 22:38:44 +0000 (15:38 -0700)]
Merge tag 'mfd-next-4.19' of git://git./linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add Cirrus Logic Madera Codec (CS47L35, CS47L85 and CS47L90/91) driver
- Add ChromeOS EC CEC driver
- Add ROHM
BD71837 PMIC driver
New Device Support:
- Add support for Dialog Semi DA9063L PMIC variant to DA9063
- Add support for Intel Ice Lake to Intel-PLSS-PCI
- Add support for X-Powers AXP806 to AXP20x
New Functionality:
- Add support for USB Charging to the ChromeOS Embedded Controller
- Add support for HDMI CEC to the ChromeOS Embedded Controller
- Add support for HDMI CEC to Intel HDMI
- Add support for accessory detection to Madera devices
- Allow individual pins to be configured via DT' wlf,csnaddr-pd
- Provide legacy platform specific EEPROM/Watchdog commands; rave-sp
Fix-upsL
- Trivial renaming/spelling fixes; cros_ec, da9063-*
- Convert to Managed Resources (devm_*); da9063-*, ti_am335x_tscadc
- Transition to helper macros/functions; da9063-*
- Constify; kempld-core
- Improve error path/messages; wm8994-core
- Disable IRQs locally instead of relying on USB subsystem; dln2
- Remove unused code; rave-sp
- New exports; sec-core
Bug Fixes:
- Fix possible false I2C transaction error; arizona-core
- Fix declared memory area size; hi655x-pmic
- Fix checksum type; rave-sp
- Fix incorrect default serial port configuration: rave-sp
- Fix incorrect coherent DMA mask for sub-devices; sm501"
* tag 'mfd-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (60 commits)
mfd: madera: Add register definitions for accessory detect
mfd: sm501: Set coherent_dma_mask when creating subdevices
mfd:
bd71837: Devicetree bindings for ROHM
BD71837 PMIC
mfd:
bd71837: Core driver for ROHM
BD71837 PMIC
media: platform: cros-ec-cec: Fix dependency on MFD_CROS_EC
mfd: sec-core: Export OF module alias table
mfd: as3722: Disable auto-power-on when AC OK
mfd: axp20x: Support AXP806 in I2C mode
mfd: axp20x: Add self-working mode support for AXP806
dt-bindings: mfd: axp20x: Add "self-working" mode for AXP806
mfd: wm8994: Allow to configure CS/ADDR Pulldown from dts
mfd: wm8994: Allow to configure Speaker Mode Pullup from dts
mfd: rave-sp: Emulate CMD_GET_STATUS on device that don't support it
mfd: rave-sp: Add legacy watchdog ping command translation
mfd: rave-sp: Add legacy EEPROM access command translation
mfd: rave-sp: Initialize flow control and parity of the port
mfd: rave-sp: Fix incorrectly specified checksum type
mfd: rave-sp: Remove unused defines
mfd: hi655x: Fix regmap area declared size for hi655x
mfd: ti_am335x_tscadc: Fix struct clk memory leak
...
Linus Torvalds [Mon, 20 Aug 2018 22:28:54 +0000 (15:28 -0700)]
Merge tag 'edac_fixes_for_4.19' of git://git./linux/kernel/git/bp/bp
Pull EDAC fix from Borislav Petkov:
"An urgent fix for a NULL ptr deref on machines with LRDDR4 DIMMs, from
Takashi Iwai"
* tag 'edac_fixes_for_4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC: Add missing MEM_LRDDR4 entry in edac_mem_types[]
Joe Perches [Mon, 20 Aug 2018 20:15:26 +0000 (13:15 -0700)]
Raise the minimum required gcc version to 4.6
Various architectures fail to build properly with older versions of the
gcc compiler.
An example from Guenter Roeck in thread [1]:
>
> In file included from ./include/linux/mm.h:17:0,
> from ./include/linux/pid_namespace.h:7,
> from ./include/linux/ptrace.h:10,
> from arch/openrisc/kernel/asm-offsets.c:32:
> ./include/linux/mm_types.h:497:16: error: flexible array member in otherwise empty struct
>
> This is just an example with gcc 4.5.1 for or32. I have seen the problem
> with gcc 4.4 (for unicore32) as well.
So update the minimum required version of gcc to 4.6.
[1] https://lore.kernel.org/lkml/
20180814170904.GA12768@roeck-us.net/
Miscellanea:
- Update Documentation/process/changes.rst
- Remove and consolidate version test blocks in compiler-gcc.h for
versions lower than 4.6
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tony Luck [Mon, 20 Aug 2018 16:31:04 +0000 (09:31 -0700)]
ia64: Fix kernel BUG at lib/ioremap.c:72!
Commit
0bbf47eab469 ("ia64: use asm-generic/io.h") results in a BUG
while booting ia64. This is because asm-generic/io.h defines
PCI_IOBASE, which results in the function acpi_pci_root_remap_iospace()
doing a lot of unnecessary (and wrong) things.
I'd suggested an #if !CONFIG_IA64 in the functon, but Arnd suggested
keeping the fix inside the arch/ia64 tree.
Fixes: 0bbf47eab469 ("ia64: use asm-generic/io.h")
Suggested-by: Arnd Bergman <arnd@arndb.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Kosina [Mon, 20 Aug 2018 16:33:50 +0000 (18:33 +0200)]
Merge branch 'for-4.19/upstream' into for-linus
Jiri Kosina [Mon, 20 Aug 2018 16:13:57 +0000 (18:13 +0200)]
Merge branch 'for-4.19/wiimote' into for-linus
Guitar-Hero devices support for hid-wiimote
Jiri Kosina [Mon, 20 Aug 2018 16:12:42 +0000 (18:12 +0200)]
Merge branch 'for-4.19/wacom' into for-linus
Wacom driver updates:
- touch_max detection improvements
- quirk handling cleanup
- get rid of wacom custom usages
Jiri Kosina [Mon, 20 Aug 2018 16:11:20 +0000 (18:11 +0200)]
Merge branch 'for-4.19/upstream' into for-linus
Assorted small driver/core fixes.
Jiri Kosina [Mon, 20 Aug 2018 16:10:33 +0000 (18:10 +0200)]
Merge branch 'for-4.19/sony' into for-linus
devm_* API conversion for hid-sony
Jiri Kosina [Mon, 20 Aug 2018 16:09:06 +0000 (18:09 +0200)]
Merge branch 'for-4.19/multitouch-multiaxis' into for-linus
Multitouch updates:
- Dial support
- Palm rejection for touchscreens
- a few small assorted fixes
Jiri Kosina [Mon, 20 Aug 2018 16:07:36 +0000 (18:07 +0200)]
Merge branch 'for-4.19/intel-ish' into for-linus
Device-specific fixes for hid-intel-ish
Jiri Kosina [Mon, 20 Aug 2018 16:07:01 +0000 (18:07 +0200)]
Merge branch 'for-4.19/i2c-hid' into for-linus
Low voltage support for i2c-hid
Jiri Kosina [Mon, 20 Aug 2018 16:06:30 +0000 (18:06 +0200)]
Merge branch 'for-4.19/elan' into for-linus
Resolution/pressure fixes and new device support for hid-elan
Jiri Kosina [Mon, 20 Aug 2018 16:05:17 +0000 (18:05 +0200)]
Merge branch 'for-4.19/cougar' into for-linus
New device support for hid-cougar
Wolfram Sang [Wed, 8 Aug 2018 07:59:28 +0000 (09:59 +0200)]
i2c: rcar: implement STOP and REP_START according to docs
When doing a REP_START after a read message, the driver used to trigger
a STOP first which would then be overwritten by REP_START. This was the
only stable method found when doing the last refactoring. However, this
was not in accordance with the documentation.
After research from our BSP team and myself, we now can implement a
version which works and is according to the documentation. The new
approach ensures the ICMCR register is only changed when really needed.
Tested on a R-Car Gen2 (H2) and Gen3 with DMA (M3N).
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Wolfram Sang [Wed, 8 Aug 2018 07:59:27 +0000 (09:59 +0200)]
i2c: rcar: refactor private flags
Use BIT macro to avoid shift-31-problem, indent a little more and use
GENMASK to make it easier to add new flags.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Hans de Goede [Sun, 12 Aug 2018 10:53:21 +0000 (12:53 +0200)]
i2c: core: ACPI: Make acpi_gsb_i2c_read_bytes() check i2c_transfer return value
Currently acpi_gsb_i2c_read_bytes() directly returns i2c_transfer's return
value. i2c_transfer returns a value < 0 on error and 2 (for 2 successfully
executed transfers) on success. But the ACPI code expects 0 on success, so
currently acpi_gsb_i2c_read_bytes()'s caller does:
if (status > 0)
status = 0;
This commit makes acpi_gsb_i2c_read_bytes() return a value which can be
directly consumed by the ACPI code, mirroring acpi_gsb_i2c_write_bytes(),
this commit also makes acpi_gsb_i2c_read_bytes() explitcly check that
i2c_transfer returns 2, rather then accepting any value > 0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Hans de Goede [Sun, 12 Aug 2018 10:53:20 +0000 (12:53 +0200)]
i2c: core: ACPI: Properly set status byte to 0 for multi-byte writes
acpi_gsb_i2c_write_bytes() returns i2c_transfer()'s return value, which
is the number of transfers executed on success, so 1.
The ACPI code expects us to store 0 in gsb->status for success, not 1.
Specifically this breaks the following code in the Thinkpad 8 DSDT:
ECWR = I2CW = ECWR /* \_SB_.I2C1.BAT0.ECWR */
If ((ECST == Zero))
{
ECRD = I2CR /* \_SB_.I2C1.I2CR */
}
Before this commit we set ECST to 1, causing the read to never happen
breaking battery monitoring on the Thinkpad 8.
This commit makes acpi_gsb_i2c_write_bytes() return 0 when i2c_transfer()
returns 1, so the single write transfer completed successfully, and
makes it return -EIO on for other (unexpected) return values >= 0.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fabrizio Castro [Tue, 14 Aug 2018 12:32:55 +0000 (13:32 +0100)]
dt-bindings: i2c: rcar: Add r8a774a1 support
Document RZ/G2M (R8A774A1) I2C compatibility with the relevant driver
dt-bindings.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fabrizio Castro [Tue, 14 Aug 2018 12:33:08 +0000 (13:33 +0100)]
dt-bindings: i2c: sh_mobile: Add r8a774a1 support
Document RZ/G2M (R8A774A1) SoC bindings.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Rafael J. Wysocki [Tue, 14 Aug 2018 10:34:40 +0000 (12:34 +0200)]
cpuidle: menu: Handle stopped tick more aggressively
Commit
87c9fe6ee495 (cpuidle: menu: Avoid selecting shallow states
with stopped tick) missed the case when the target residencies of
deep idle states of CPUs are above the tick boundary which may cause
the CPU to get stuck in a shallow idle state for a long time.
Say there are two CPU idle states available: one shallow, with the
target residency much below the tick boundary and one deep, with
the target residency significantly above the tick boundary. In
that case, if the tick has been stopped already and the expected
next timer event is relatively far in the future, the governor will
assume the idle duration to be equal to TICK_USEC and it will select
the idle state for the CPU accordingly. However, that will cause the
shallow state to be selected even though it would have been more
energy-efficient to select the deep one.
To address this issue, modify the governor to always use the time
till the closest timer event instead of the predicted idle duration
if the latter is less than the tick period length and the tick has
been stopped already. Also make it extend the search for a matching
idle state if the tick is stopped to avoid settling on a shallow
state if deep states with target residencies above the tick period
length are available.
In addition, make it always indicate that the tick should be stopped
if it has been stopped already for consistency.
Fixes: 87c9fe6ee495 (cpuidle: menu: Avoid selecting shallow states with stopped tick)
Reported-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: 4.17+ <stable@vger.kernel.org> # 4.17+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rafael J. Wysocki [Thu, 9 Aug 2018 17:08:34 +0000 (19:08 +0200)]
sched: idle: Avoid retaining the tick when it has been stopped
If the tick has been stopped already, but the governor has not asked to
stop it (which it can do sometimes), the idle loop should invoke
tick_nohz_idle_stop_tick(), to let tick_nohz_stop_tick() take care
of this case properly.
Fixes: 554c8aa8ecad (sched: idle: Select idle state before stopping the tick)
Cc: 4.17+ <stable@vger.kernel.org> # 4.17+
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Esben Haabendal [Thu, 16 Aug 2018 08:43:13 +0000 (10:43 +0200)]
i2c: imx: Simplify stopped state tracking
Always update the stopped state when busy status have been checked.
This is identical to what was done before, with the exception of error
handling.
Without this change, some errors cause the stopped state to be left in
incorrect state in i2c_imx_stop(), i2c_imx_dma_read(), i2c_imx_read() and
i2c_imx_xfer().
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Esben Haabendal [Thu, 16 Aug 2018 08:43:12 +0000 (10:43 +0200)]
i2c: imx: Fix race condition in dma read
This fixes a race condition, where the DMAEN bit ends up being set after
I2C slave has transmitted a byte following the dummy read. When that
happens, an interrupt is generated instead, and no DMA request is generated
to kickstart the DMA read, and a timeout happens after DMA_TIMEOUT (1 sec).
Fixed by setting the DMAEN bit before the dummy read.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Darren Stevens [Sun, 31 Dec 2017 20:53:55 +0000 (20:53 +0000)]
i2c: pasemi: remove hardcoded bus numbers on smbus
The pasemi smbus controller uses PCI_FUNC(dev->devfn) to define which
number bus to attach to, however this fails when something else is
probed first, for example an ATI Radeon graphics card will claim 9 or
10 busses, including the ones the pasemi wants.
Patch the driver to call i2c_add_adapter rather than
i2c_add_numbered_adapter.
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Andy Shevchenko [Fri, 10 Aug 2018 10:26:49 +0000 (13:26 +0300)]
i2c: designware: Add SPDX license tag
Replace short statement in comment with proper SPDX license tag.
Note, for i2c-desingware-slave.c the identifier is chosen
in accordance with MODULE_LICENSE() macro since it is visible to user.
Another point to this choice is that the header seems to be copy'n'paste
from the other file of this very driver.
Acked-by: Luis Oliveira <Luis.Oliveira@synopsys.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Linus Torvalds [Sun, 19 Aug 2018 23:23:03 +0000 (16:23 -0700)]
Merge branch 'for-next' of git://git./linux/kernel/git/gerg/m68knommu
Pull m68knommu updates from Greg Ungerer:
"Only two changes.
One cleans up warnings in the ColdFire DMA code, the other stubs out
(with warnings) ColdFire clock api functions not normally used"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: Fix typos in Coldfire 5272 DMA debug code
m68k: coldfire: Normalize clk API
Linus Torvalds [Sun, 19 Aug 2018 18:51:45 +0000 (11:51 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Fix races in IPVS, from Tan Hu.
2) Missing unbind in matchall classifier, from Hangbin Liu.
3) Missing act_ife action release, from Vlad Buslov.
4) Cure lockdep splats in ila, from Cong Wang.
5) veth queue leak on link delete, from Toshiaki Makita.
6) Disable isdn's IIOCDBGVAR ioctl, it exposes kernel addresses. From
Kees Cook.
7) RCU usage fixup in XDP, from Tariq Toukan.
8) Two TCP ULP fixes from Daniel Borkmann.
9) r8169 needs REALTEK_PHY as a Kconfig dependency, from Heiner
Kallweit.
10) Always take tcf_lock with BH disabled, otherwise we can deadlock
with rate estimator code paths. From Vlad Buslov.
11) Don't use MSI-X on RTL8106e r8169 chips, they don't resume properly.
From Jian-Hong Pan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
ip6_vti: fix creating fallback tunnel device for vti6
ip_vti: fix a null pointer deferrence when create vti fallback tunnel
r8169: don't use MSI-X on RTL8106e
net: lan743x_ptp: convert to ktime_get_clocktai_ts64
net: sched: always disable bh when taking tcf_lock
ip6_vti: simplify stats handling in vti6_xmit
bpf: fix redirect to map under tail calls
r8169: add missing Kconfig dependency
tools/bpf: fix bpf selftest test_cgroup_storage failure
bpf, sockmap: fix sock_map_ctx_update_elem race with exist/noexist
bpf, sockmap: fix map elem deletion race with smap_stop_sock
bpf, sockmap: fix leakage of smap_psock_map_entry
tcp, ulp: fix leftover icsk_ulp_ops preventing sock from reattach
tcp, ulp: add alias for all ulp modules
bpf: fix a rcu usage warning in bpf_prog_array_copy_core()
samples/bpf: all XDP samples should unload xdp/bpf prog on SIGTERM
net/xdp: Fix suspicious RCU usage warning
net/mlx5e: Delete unneeded function argument
Documentation: networking: ti-cpsw: correct cbs parameters for Eth1 100Mb
isdn: Disable IIOCDBGVAR
...
Haishuang Yan [Sun, 19 Aug 2018 07:05:05 +0000 (15:05 +0800)]
ip6_vti: fix creating fallback tunnel device for vti6
When set fb_tunnels_only_for_init_net to 1, don't create fallback tunnel
device for vti6 when a new namespace is created.
Tested:
[root@builder2 ~]# modprobe ip6_tunnel
[root@builder2 ~]# modprobe ip6_vti
[root@builder2 ~]# echo 1 > /proc/sys/net/core/fb_tunnels_only_for_init_net
[root@builder2 ~]# unshare -n
[root@builder2 ~]# ip link
1: lo: <LOOPBACK> mtu 65536 qdisc noop state DOWN mode DEFAULT group
default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Haishuang Yan [Sun, 19 Aug 2018 07:05:04 +0000 (15:05 +0800)]
ip_vti: fix a null pointer deferrence when create vti fallback tunnel
After set fb_tunnels_only_for_init_net to 1, the itn->fb_tunnel_dev will
be NULL and will cause following crash:
[ 2742.849298] BUG: unable to handle kernel NULL pointer dereference at
0000000000000941
[ 2742.851380] PGD
800000042c21a067 P4D
800000042c21a067 PUD
42aaed067 PMD 0
[ 2742.852818] Oops: 0002 [#1] SMP PTI
[ 2742.853570] CPU: 7 PID: 2484 Comm: unshare Kdump: loaded Not tainted 4.18.0-rc8+ #2
[ 2742.855163] Hardware name: Fedora Project OpenStack Nova, BIOS seabios-1.7.5-11.el7 04/01/2014
[ 2742.856970] RIP: 0010:vti_init_net+0x3a/0x50 [ip_vti]
[ 2742.858034] Code: 90 83 c0 48 c7 c2 20 a1 83 c0 48 89 fb e8 6e 3b f6 ff 85 c0 75 22 8b 0d f4 19 00 00 48 8b 93 00 14 00 00 48 8b 14 ca 48 8b 12 <c6> 82 41 09 00 00 04 c6 82 38 09 00 00 45 5b c3 66 0f 1f 44 00 00
[ 2742.861940] RSP: 0018:
ffff9be28207fde0 EFLAGS:
00010246
[ 2742.863044] RAX:
0000000000000000 RBX:
ffff8a71ebed4980 RCX:
0000000000000013
[ 2742.864540] RDX:
0000000000000000 RSI:
0000000000000013 RDI:
ffff8a71ebed4980
[ 2742.866020] RBP:
ffff8a71ea717000 R08:
ffffffffc083903c R09:
ffff8a71ea717000
[ 2742.867505] R10:
0000000000000000 R11:
0000000000000000 R12:
ffff8a71ebed4980
[ 2742.868987] R13:
0000000000000013 R14:
ffff8a71ea5b49c0 R15:
0000000000000000
[ 2742.870473] FS:
00007f02266c9740(0000) GS:
ffff8a71ffdc0000(0000) knlGS:
0000000000000000
[ 2742.872143] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 2742.873340] CR2:
0000000000000941 CR3:
000000042bc20006 CR4:
00000000001606e0
[ 2742.874821] Call Trace:
[ 2742.875358] ops_init+0x38/0xf0
[ 2742.876078] setup_net+0xd9/0x1f0
[ 2742.876789] copy_net_ns+0xb7/0x130
[ 2742.877538] create_new_namespaces+0x11a/0x1d0
[ 2742.878525] unshare_nsproxy_namespaces+0x55/0xa0
[ 2742.879526] ksys_unshare+0x1a7/0x330
[ 2742.880313] __x64_sys_unshare+0xe/0x20
[ 2742.881131] do_syscall_64+0x5b/0x180
[ 2742.881933] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reproduce:
echo 1 > /proc/sys/net/core/fb_tunnels_only_for_init_net
modprobe ip_vti
unshare -n
Fixes: 79134e6ce2c9 ("net: do not create fallback tunnels for non-default namespaces")
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian-Hong Pan [Fri, 17 Aug 2018 05:07:35 +0000 (13:07 +0800)]
r8169: don't use MSI-X on RTL8106e
Found the ethernet network on ASUS X441UAR doesn't come back on resume
from suspend when using MSI-X. The chip is RTL8106e - version 39.
[ 21.848357] libphy: r8169: probed
[ 21.848473] r8169 0000:02:00.0 eth0: RTL8106e, 0c:9d:92:32:67:b4, XID
44900000, IRQ 127
[ 22.518860] r8169 0000:02:00.0 enp2s0: renamed from eth0
[ 29.458041] Generic PHY r8169-200:00: attached PHY driver [Generic
PHY] (mii_bus:phy_addr=r8169-200:00, irq=IGNORE)
[ 63.227398] r8169 0000:02:00.0 enp2s0: Link is Up - 100Mbps/Full -
flow control off
[ 124.514648] Generic PHY r8169-200:00: attached PHY driver [Generic
PHY] (mii_bus:phy_addr=r8169-200:00, irq=IGNORE)
Here is the ethernet controller in detail:
02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL8101/2/6E PCI Express Fast/Gigabit Ethernet controller [10ec:8136]
(rev 07)
Subsystem: ASUSTeK Computer Inc. RTL810xE PCI Express Fast
Ethernet controller [1043:200f]
Flags: bus master, fast devsel, latency 0, IRQ 16
I/O ports at e000 [size=256]
Memory at
ef100000 (64-bit, non-prefetchable) [size=4K]
Memory at
e0000000 (64-bit, prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: r8169
Kernel modules: r8169
Falling back to MSI fixes the issue.
Fixes: 6c6aa15fdea5 ("r8169: improve interrupt handling")
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Wed, 15 Aug 2018 17:49:49 +0000 (19:49 +0200)]
net: lan743x_ptp: convert to ktime_get_clocktai_ts64
timekeeping_clocktai64() has been renamed to ktime_get_clocktai_ts64()
for consistency with the other ktime_get_* access functions.
Rename the new caller that has come up as well.
Question: this is the only ptp driver that sets the hardware time
to the current system time in TAI. Why does it do that?
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Buslov [Tue, 14 Aug 2018 18:46:16 +0000 (21:46 +0300)]
net: sched: always disable bh when taking tcf_lock
Recently, ops->init() and ops->dump() of all actions were modified to
always obtain tcf_lock when accessing private action state. Actions that
don't depend on tcf_lock for synchronization with their data path use
non-bh locking API. However, tcf_lock is also used to protect rate
estimator stats in softirq context by timer callback.
Change ops->init() and ops->dump() of all actions to disable bh when using
tcf_lock to prevent deadlock reported by following lockdep warning:
[ 105.470398] ================================
[ 105.475014] WARNING: inconsistent lock state
[ 105.479628] 4.18.0-rc8+ #664 Not tainted
[ 105.483897] --------------------------------
[ 105.488511] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
[ 105.494871] swapper/16/0 [HC0[0]:SC1[1]:HE1:SE0] takes:
[ 105.500449]
00000000f86c012e (&(&p->tcfa_lock)->rlock){+.?.}, at: est_fetch_counters+0x3c/0xa0
[ 105.509696] {SOFTIRQ-ON-W} state was registered at:
[ 105.514925] _raw_spin_lock+0x2c/0x40
[ 105.519022] tcf_bpf_init+0x579/0x820 [act_bpf]
[ 105.523990] tcf_action_init_1+0x4e4/0x660
[ 105.528518] tcf_action_init+0x1ce/0x2d0
[ 105.532880] tcf_exts_validate+0x1d8/0x200
[ 105.537416] fl_change+0x55a/0x268b [cls_flower]
[ 105.542469] tc_new_tfilter+0x748/0xa20
[ 105.546738] rtnetlink_rcv_msg+0x56a/0x6d0
[ 105.551268] netlink_rcv_skb+0x18d/0x200
[ 105.555628] netlink_unicast+0x2d0/0x370
[ 105.559990] netlink_sendmsg+0x3b9/0x6a0
[ 105.564349] sock_sendmsg+0x6b/0x80
[ 105.568271] ___sys_sendmsg+0x4a1/0x520
[ 105.572547] __sys_sendmsg+0xd7/0x150
[ 105.576655] do_syscall_64+0x72/0x2c0
[ 105.580757] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 105.586243] irq event stamp: 489296
[ 105.590084] hardirqs last enabled at (489296): [<
ffffffffb507e639>] _raw_spin_unlock_irq+0x29/0x40
[ 105.599765] hardirqs last disabled at (489295): [<
ffffffffb507e745>] _raw_spin_lock_irq+0x15/0x50
[ 105.609277] softirqs last enabled at (489292): [<
ffffffffb413a6a3>] irq_enter+0x83/0xa0
[ 105.618001] softirqs last disabled at (489293): [<
ffffffffb413a800>] irq_exit+0x140/0x190
[ 105.626813]
other info that might help us debug this:
[ 105.633976] Possible unsafe locking scenario:
[ 105.640526] CPU0
[ 105.643325] ----
[ 105.646125] lock(&(&p->tcfa_lock)->rlock);
[ 105.650747] <Interrupt>
[ 105.653717] lock(&(&p->tcfa_lock)->rlock);
[ 105.658514]
*** DEADLOCK ***
[ 105.665349] 1 lock held by swapper/16/0:
[ 105.669629] #0:
00000000a640ad99 ((&est->timer)){+.-.}, at: call_timer_fn+0x10b/0x550
[ 105.678200]
stack backtrace:
[ 105.683194] CPU: 16 PID: 0 Comm: swapper/16 Not tainted 4.18.0-rc8+ #664
[ 105.690249] Hardware name: Supermicro SYS-2028TP-DECR/X10DRT-P, BIOS 2.0b 03/30/2017
[ 105.698626] Call Trace:
[ 105.701421] <IRQ>
[ 105.703791] dump_stack+0x92/0xeb
[ 105.707461] print_usage_bug+0x336/0x34c
[ 105.711744] mark_lock+0x7c9/0x980
[ 105.715500] ? print_shortest_lock_dependencies+0x2e0/0x2e0
[ 105.721424] ? check_usage_forwards+0x230/0x230
[ 105.726315] __lock_acquire+0x923/0x26f0
[ 105.730597] ? debug_show_all_locks+0x240/0x240
[ 105.735478] ? mark_lock+0x493/0x980
[ 105.739412] ? check_chain_key+0x140/0x1f0
[ 105.743861] ? __lock_acquire+0x836/0x26f0
[ 105.748323] ? lock_acquire+0x12e/0x290
[ 105.752516] lock_acquire+0x12e/0x290
[ 105.756539] ? est_fetch_counters+0x3c/0xa0
[ 105.761084] _raw_spin_lock+0x2c/0x40
[ 105.765099] ? est_fetch_counters+0x3c/0xa0
[ 105.769633] est_fetch_counters+0x3c/0xa0
[ 105.773995] est_timer+0x87/0x390
[ 105.777670] ? est_fetch_counters+0xa0/0xa0
[ 105.782210] ? lock_acquire+0x12e/0x290
[ 105.786410] call_timer_fn+0x161/0x550
[ 105.790512] ? est_fetch_counters+0xa0/0xa0
[ 105.795055] ? del_timer_sync+0xd0/0xd0
[ 105.799249] ? __lock_is_held+0x93/0x110
[ 105.803531] ? mark_held_locks+0x20/0xe0
[ 105.807813] ? _raw_spin_unlock_irq+0x29/0x40
[ 105.812525] ? est_fetch_counters+0xa0/0xa0
[ 105.817069] ? est_fetch_counters+0xa0/0xa0
[ 105.821610] run_timer_softirq+0x3c4/0x9f0
[ 105.826064] ? lock_acquire+0x12e/0x290
[ 105.830257] ? __bpf_trace_timer_class+0x10/0x10
[ 105.835237] ? __lock_is_held+0x25/0x110
[ 105.839517] __do_softirq+0x11d/0x7bf
[ 105.843542] irq_exit+0x140/0x190
[ 105.847208] smp_apic_timer_interrupt+0xac/0x3b0
[ 105.852182] apic_timer_interrupt+0xf/0x20
[ 105.856628] </IRQ>
[ 105.859081] RIP: 0010:cpuidle_enter_state+0xd8/0x4d0
[ 105.864395] Code: 46 ff 48 89 44 24 08 0f 1f 44 00 00 31 ff e8 cf ec 46 ff 80 7c 24 07 00 0f 85 1d 02 00 00 e8 9f 90 4b ff fb 66 0f 1f 44 00 00 <4c> 8b 6c 24 08 4d 29 fd 0f 80 36 03 00 00 4c 89 e8 48 ba cf f7 53
[ 105.884288] RSP: 0018:
ffff8803ad94fd20 EFLAGS:
00000246 ORIG_RAX:
ffffffffffffff13
[ 105.892494] RAX:
0000000000000000 RBX:
ffffe8fb300829c0 RCX:
ffffffffb41e19e1
[ 105.899988] RDX:
0000000000000007 RSI:
dffffc0000000000 RDI:
ffff8803ad9358ac
[ 105.907503] RBP:
ffffffffb6636300 R08:
0000000000000004 R09:
0000000000000000
[ 105.914997] R10:
0000000000000000 R11:
0000000000000000 R12:
0000000000000004
[ 105.922487] R13:
ffffffffb6636140 R14:
ffffffffb66362d8 R15:
000000188d36091b
[ 105.929988] ? trace_hardirqs_on_caller+0x141/0x2d0
[ 105.935232] do_idle+0x28e/0x320
[ 105.938817] ? arch_cpu_idle_exit+0x40/0x40
[ 105.943361] ? mark_lock+0x8c1/0x980
[ 105.947295] ? _raw_spin_unlock_irqrestore+0x32/0x60
[ 105.952619] cpu_startup_entry+0xc2/0xd0
[ 105.956900] ? cpu_in_idle+0x20/0x20
[ 105.960830] ? _raw_spin_unlock_irqrestore+0x32/0x60
[ 105.966146] ? trace_hardirqs_on_caller+0x141/0x2d0
[ 105.971391] start_secondary+0x2b5/0x360
[ 105.975669] ? set_cpu_sibling_map+0x1330/0x1330
[ 105.980654] secondary_startup_64+0xa5/0xb0
Taking tcf_lock in sample action with bh disabled causes lockdep to issue a
warning regarding possible irq lock inversion dependency between tcf_lock,
and psample_groups_lock that is taken when holding tcf_lock in sample init:
[ 162.108959] Possible interrupt unsafe locking scenario:
[ 162.116386] CPU0 CPU1
[ 162.121277] ---- ----
[ 162.126162] lock(psample_groups_lock);
[ 162.130447] local_irq_disable();
[ 162.136772] lock(&(&p->tcfa_lock)->rlock);
[ 162.143957] lock(psample_groups_lock);
[ 162.150813] <Interrupt>
[ 162.153808] lock(&(&p->tcfa_lock)->rlock);
[ 162.158608]
*** DEADLOCK ***
In order to prevent potential lock inversion dependency between tcf_lock
and psample_groups_lock, extract call to psample_group_get() from tcf_lock
protected section in sample action init function.
Fixes: 4e232818bd32 ("net: sched: act_mirred: remove dependency on rtnl lock")
Fixes: 764e9a24480f ("net: sched: act_vlan: remove dependency on rtnl lock")
Fixes: 729e01260989 ("net: sched: act_tunnel_key: remove dependency on rtnl lock")
Fixes: d77284956656 ("net: sched: act_sample: remove dependency on rtnl lock")
Fixes: e8917f437006 ("net: sched: act_gact: remove dependency on rtnl lock")
Fixes: b6a2b971c0b0 ("net: sched: act_csum: remove dependency on rtnl lock")
Fixes: 2142236b4584 ("net: sched: act_bpf: remove dependency on rtnl lock")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 19 Aug 2018 17:38:36 +0000 (10:38 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull first set of KVM updates from Paolo Bonzini:
"PPC:
- minor code cleanups
x86:
- PCID emulation and CR3 caching for shadow page tables
- nested VMX live migration
- nested VMCS shadowing
- optimized IPI hypercall
- some optimizations
ARM will come next week"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (85 commits)
kvm: x86: Set highest physical address bits in non-present/reserved SPTEs
KVM/x86: Use CC_SET()/CC_OUT in arch/x86/kvm/vmx.c
KVM: X86: Implement PV IPIs in linux guest
KVM: X86: Add kvm hypervisor init time platform setup callback
KVM: X86: Implement "send IPI" hypercall
KVM/x86: Move X86_CR4_OSXSAVE check into kvm_valid_sregs()
KVM: x86: Skip pae_root shadow allocation if tdp enabled
KVM/MMU: Combine flushing remote tlb in mmu_set_spte()
KVM: vmx: skip VMWRITE of HOST_{FS,GS}_BASE when possible
KVM: vmx: skip VMWRITE of HOST_{FS,GS}_SEL when possible
KVM: vmx: always initialize HOST_{FS,GS}_BASE to zero during setup
KVM: vmx: move struct host_state usage to struct loaded_vmcs
KVM: vmx: compute need to reload FS/GS/LDT on demand
KVM: nVMX: remove a misleading comment regarding vmcs02 fields
KVM: vmx: rename __vmx_load_host_state() and vmx_save_host_state()
KVM: vmx: add dedicated utility to access guest's kernel_gs_base
KVM: vmx: track host_state.loaded using a loaded_vmcs pointer
KVM: vmx: refactor segmentation code in vmx_save_host_state()
kvm: nVMX: Fix fault priority for VMX operations
kvm: nVMX: Fix fault vector for VMX operation at CPL > 0
...
Linus Torvalds [Sun, 19 Aug 2018 16:56:38 +0000 (09:56 -0700)]
Merge tag 'riscv-for-linus-4.19-mw0' of git://git./linux/kernel/git/palmer/riscv-linux
Pull RISC-V updates from Palmer Dabbelt:
"This contains some major improvements to the RISC-V port, including
the necessary interrupt controller and timer support to actually make
it to userspace. Support for three devices has been added:
- the ISA-mandated timers on RISC-V systems.
- the ISA-mandated first-level interrupt controller on RISC-V
systems, which is handled as part of our core arch code because
it's very small and tightly tied to the ISA.
- SiFive's platform-level interrupt controller, which talks to the
actual devices.
In addition to these new devices, there are a handful of cleanups all
over the RISC-V tree:
- build fixes for various configurations:
* A fix to the vDSO build's makefile so it respects CFLAGS.
* The addition of __lshrti3, a libgcc derived function necessary
for some 32-bit configurations.
* !SMP && PERF_EVENTS
- Cleanups to the arch code to remove the remnants of old versions of
the drivers that were just properly submitted.
* Some dead code from the timer driver, most of which wasn't ever
even compiled.
* Cleanups of some interrupt #defines, which are now local to the
interrupt handling code.
- Fixes to ptrace(), which while not being sufficient to fully make
GDB work are at least sufficient to get simple GDB tasks to work.
- Early printk support via RISC-V's architecturally mandated SBI
console device.
- A fix to our early debug trap handler to ensure it's always
aligned.
These patches have all been through a fairly extensive review process,
but as this enables a whole pile of functionality (ie, userspace) I'm
confident we'll need to submit a few more patches. The only concrete
issues I know about are the sys_riscv_flush_icache patches, but as I
managed to screw those up on Friday I figured it'd be best to let them
bake another week.
This tag boots a Fedora root filesystem on QEMU's master branch for
me, and before this morning's rebase (from 4.18-rc8 to 4.18) it booted
on the HiFive Unleashed.
Thanks to Christoph Hellwig and the other guys at WD for getting the
new drivers in shape!"
* tag 'riscv-for-linus-4.19-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
dt-bindings: interrupt-controller: SiFive Plaform Level Interrupt Controller
dt-bindings: interrupt-controller: RISC-V local interrupt controller
RISC-V: Fix !CONFIG_SMP compilation error
irqchip: add a SiFive PLIC driver
RISC-V: Add the directive for alignment of stvec's value
clocksource: new RISC-V SBI timer driver
RISC-V: implement low-level interrupt handling
RISC-V: add a definition for the SIE SEIE bit
RISC-V: remove INTERRUPT_CAUSE_* defines from asm/irq.h
RISC-V: simplify software interrupt / IPI code
RISC-V: remove timer leftovers
RISC-V: Add early printk support via the SBI console
RISC-V: Don't increment sepc after breakpoint.
RISC-V: implement __lshrti3.
RISC-V: Use KBUILD_CFLAGS instead of KCFLAGS when building the vDSO
Linus Torvalds [Sun, 19 Aug 2018 16:30:44 +0000 (09:30 -0700)]
Merge tag 'char-misc-4.19-rc1' of git://git./linux/kernel/git/gregkh/char-misc
Pull UIO fix from Greg KH:
"Here is a single UIO fix that I forgot to send before 4.18-final came
out. It reverts a UIO patch that went in the 4.18 development window
that was causing problems.
This patch has been in linux-next for a while with no problems, I just
forgot to send it earlier, or as part of the larger char/misc patch
series from yesterday, my fault"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Revert "uio: use request_threaded_irq instead"
Linus Torvalds [Sat, 18 Aug 2018 23:48:07 +0000 (16:48 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- a new driver for Rohm BU21029 touch controller
- new bitmap APIs: bitmap_alloc, bitmap_zalloc and bitmap_free
- updates to Atmel, eeti. pxrc and iforce drivers
- assorted driver cleanups and fixes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
MAINTAINERS: Add PhoenixRC Flight Controller Adapter
Input: do not use WARN() in input_alloc_absinfo()
Input: mark expected switch fall-throughs
Input: raydium_i2c_ts - use true and false for boolean values
Input: evdev - switch to bitmap API
Input: gpio-keys - switch to bitmap_zalloc()
Input: elan_i2c_smbus - cast sizeof to int for comparison
bitmap: Add bitmap_alloc(), bitmap_zalloc() and bitmap_free()
md: Avoid namespace collision with bitmap API
dm: Avoid namespace collision with bitmap API
Input: pm8941-pwrkey - add resin entry
Input: pm8941-pwrkey - abstract register offsets and event code
Input: iforce - reorganize joystick configuration lists
Input: atmel_mxt_ts - move completion to after config crc is updated
Input: atmel_mxt_ts - don't report zero pressure from T9
Input: atmel_mxt_ts - zero terminate config firmware file
Input: atmel_mxt_ts - refactor config update code to add context struct
Input: atmel_mxt_ts - config CRC may start at T71
Input: atmel_mxt_ts - remove unnecessary debug on ENOMEM
Input: atmel_mxt_ts - remove duplicate setup of ABS_MT_PRESSURE
...
Linus Torvalds [Sat, 18 Aug 2018 23:45:27 +0000 (16:45 -0700)]
Merge tag 'hwlock-v4.19' of git://github.com/andersson/remoteproc
Pull hwspinlock updates from Bjorn Andersson:
"This introduces devres helpers and an API to request a lock by name,
then migrates the sprd SPI driver to use these"
* tag 'hwlock-v4.19' of git://github.com/andersson/remoteproc:
hwspinlock: Fix incorrect return pointers
spi: sprd: Change to use devm_hwspin_lock_request_specific()
spi: sprd: Replace of_hwspin_lock_get_id() with of_hwspin_lock_get_id_byname()
hwspinlock: Fix one comment mistake
hwspinlock: Remove redundant config
hwspinlock: Add devm_xxx() APIs to register/unregister one hwlock controller
hwspinlock: Add devm_xxx() APIs to request/free hwlock
hwspinlock: Add one new API to support getting a specific hwlock by the name
Linus Torvalds [Sat, 18 Aug 2018 23:43:57 +0000 (16:43 -0700)]
Merge tag 'rpmsg-v4.19' of git://github.com/andersson/remoteproc
Pull rpmsg updates from Bjorn Andersson:
"This fixes a few compile and kerneldoc warnings, allows rpmsg devices
to handle power domains, allow for labeling GLINK edges and supports
compat for rpmsg_char"
* tag 'rpmsg-v4.19' of git://github.com/andersson/remoteproc:
rpmsg: Add compat ioctl for rpmsg char driver
rpmsg: glink: Store edge name for glink device
dt-bindings: soc: qcom: Add label for GLINK bindings
rpmsg: core: add support to power domains for devices
rpmsg: smd: fix kerneldoc warnings
rpmsg: glink: Fix various kerneldoc warnings.
rpmsg: glink: correctly annotate intent members
rpmsg: smd: Add missing include of sizes.h
Linus Torvalds [Sat, 18 Aug 2018 23:42:04 +0000 (16:42 -0700)]
Merge tag 'rproc-v4.19' of git://github.com/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"This adds support for pre-start and post-shutdown hooks for remoteproc
subdevices, refactors the Qualcomm Hexagon support to allow reuse
between several drivers, makes authentication in the MDT file loader
optional, migrates a few format strings to use %pK and migrates the
Davinci driver to use the reset framework"
* tag 'rproc-v4.19' of git://github.com/andersson/remoteproc:
remoteproc/davinci: use the reset framework
remoteproc/davinci: Mark error recovery as disabled
remoteproc: st_slim: replace "%p" with "%pK"
remoteproc: replace "%p" with "%pK"
remoteproc: qcom: fix Q6V5_WCSS dependencies
remoteproc: Reset table_ptr in rproc_start() failure paths
remoteproc: qcom: q6v5-pil: fix modem hang on SDM845 after axis2 clk unvote
remoteproc: qcom q6v5: fix modular build
remoteproc: Introduce prepare and unprepare for subdevices
remoteproc: rename subdev probe and remove functions
remoteproc: Make client initialize ops in rproc_subdev
remoteproc: Make start and stop in subdev optional
remoteproc: Rename subdev functions to start/stop
remoteproc: qcom: Introduce Hexagon V5 based WCSS driver
remoteproc: qcom: q6v5-pil: Use common q6v5 helpers
remoteproc: qcom: adsp: Use common q6v5 helpers
remoteproc: q6v5: Extract common resource handling
remoteproc: qcom: mdt_loader: Make the firmware authentication optional
Linus Torvalds [Sat, 18 Aug 2018 23:16:57 +0000 (16:16 -0700)]
Merge tag 'linux-watchdog-4.19-rc1' of git://linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- add MEN 16z069 IP-Core driver
- renesas-wdt: add support for the R8A77990 wdt
- stm32_iwdg: Add stm32mp1 support and pclk feature
- sp805_wdt, orion_wdt, sprd_wdt: several improvements
- imx2_wdt, stmp3xxx: switch to SPDX identifier
* tag 'linux-watchdog-4.19-rc1' of git://www.linux-watchdog.org/linux-watchdog:
watchdog: fix dependencies of menz69_wdt.o
watchdog: sp805: Add clock-frequency property
watchdog: add driver for the MEN 16z069 IP-Core
watchdog: sprd_wdt: Remove redundant dev_err call in sprd_wdt_probe()
watchdog: stmp3xxx: Switch to SPDX identifier
watchdog: imx2_wdt: Switch to SPDX identifier
watchdog: sp805: set WDOG_HW_RUNNING when appropriate
watchdog: sp805: add 'timeout-sec' DT property support
dt-bindings: watchdog: Add optional 'timeout-sec' property for sp805
dt-bindings: watchdog: Consolidate SP805 binding docs
watchdog: orion_wdt: Mark watchdog as active when running at probe
watchdog: stm32: add pclk feature for stm32mp1
dt-bindings: watchdog: add stm32mp1 support
dt-bindings: watchdog: renesas-wdt: Add support for the R8A77990 wdt
Linus Torvalds [Sat, 18 Aug 2018 22:55:59 +0000 (15:55 -0700)]
Merge tag 'dmaengine-4.19-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull DMAengine updates from Vinod Koul:
"This round brings couple of framework changes, a new driver and usual
driver updates:
- new managed helper for dmaengine framework registration
- split dmaengine pause capability to pause and resume and allow
drivers to report that individually
- update dma_request_chan_by_mask() to handle deferred probing
- move imx-sdma to use virt-dma
- new driver for Actions Semi Owl family S900 controller
- minor updates to intel, renesas, mv_xor, pl330 etc"
* tag 'dmaengine-4.19-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (46 commits)
dmaengine: Add Actions Semi Owl family S900 DMA driver
dt-bindings: dmaengine: Add binding for Actions Semi Owl SoCs
dmaengine: sh: rcar-dmac: Should not stop the DMAC by rcar_dmac_sync_tcr()
dmaengine: mic_x100_dma: use the new helper to simplify the code
dmaengine: add a new helper dmaenginem_async_device_register
dmaengine: imx-sdma: add memcpy interface
dmaengine: imx-sdma: add SDMA_BD_MAX_CNT to replace '0xffff'
dmaengine: dma_request_chan_by_mask() to handle deferred probing
dmaengine: pl330: fix irq race with terminate_all
dmaengine: Revert "dmaengine: mv_xor_v2: enable COMPILE_TEST"
dmaengine: mv_xor_v2: use {lower,upper}_32_bits to configure HW descriptor address
dmaengine: mv_xor_v2: enable COMPILE_TEST
dmaengine: mv_xor_v2: move unmap to before callback
dmaengine: mv_xor_v2: convert callback to helper function
dmaengine: mv_xor_v2: kill the tasklets upon exit
dmaengine: mv_xor_v2: explicitly freeup irq
dmaengine: sh: rcar-dmac: Add dma_pause operation
dmaengine: sh: rcar-dmac: add a new function to clear CHCR.DE with barrier
dmaengine: idma64: Support dmaengine_terminate_sync()
dmaengine: hsu: Support dmaengine_terminate_sync()
...
Linus Torvalds [Sat, 18 Aug 2018 22:54:05 +0000 (15:54 -0700)]
Merge tag 'mmc-v4.19' of git://git./linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"Updates for MMC for v4.19.
MMC core:
- Add some fine-grained hooks to further support HS400 tuning
- Improve error path for bus width setting for HS400es
- Use a common method when checking R1 status
MMC host:
- renesas_sdhi: Add r8a77990 support
- renesas_sdhi: Add eMMC HS400 mode support
- tmio/renesas_sdhi: Improve tuning/clock management
- tmio: Add eMMC HS400 mode support
- sunxi: Add support for 3.3V eMMC DDR mode
- mmci: Initial support to manage variant specific callbacks
- sdhci: Don't try 3.3V I/O voltage if not supported
- sdhci-pci-dwc-mshc: Add driver to support Synopsys dwc mshc SDHCI PCI
- sdhci-of-dwcmshc: Add driver to support Synopsys DWC MSHC SDHCI
- sdhci-msm: Add support for new version sdcc V5
- sdhci-pci-o2micro: Add support for O2 eMMC HS200 mode
- sdhci-pci-o2micro: Add support for O2 hardware tuning
- sdhci-pci-o2micro: Add MSI interrupt support for O2 SD host
- sdhci-pci: Add support for Intel ICP
- sdhci-tegra: Prevent ACMD23 and HS200 mode on Tegra 3
- sdhci-tegra: Fix eMMC DDR52 mode
- sdhci-tegra: Improve clock management
- dw_mmc-rockchip: Document compatible string for px30
- sdhci-esdhc-imx: Add support for 3.3V eMMC DDR mode
- sdhci-of-esdhc: Set proper DMA mask for ls104x chips
- sdhci-of-esdhc: Improve clock management
- sdhci-of-arasan: Add a quirk to manage unstable clocks
- dw_mmc-exynos: Address potential external abort during system resume
- pxamci: Add support for common MMC DT bindings
- pxamci: Several cleanups and improvements
- pxamci: Merge immutable branch for pxa to switch to DMA slave maps"
* tag 'mmc-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (56 commits)
mmc: core: improve reasonableness of bus width setting for HS400es
mmc: tmio: remove unneeded variable in tmio_mmc_start_command()
mmc: renesas_sdhi: Fix sampling clock position selecting
mmc: tmio: Fix tuning flow
mmc: sunxi: remove output of virtual base address
dt-bindings: mmc: rockchip-dw-mshc: add description for px30
mmc: renesas_sdhi: Add r8a77990 support
mmc: sunxi: allow 3.3V DDR when DDR is available
mmc: mmci: Add and implement a ->dma_setup() callback for qcom dml
mmc: mmci: Initial support to manage variant specific callbacks
mmc: tegra: Force correct divider calculation on DDR50/52
mmc: sdhci: Add MSI interrupt support for O2 SD host
mmc: sdhci: Add support for O2 hardware tuning
mmc: sdhci: Export sdhci tuning function symbol
mmc: sdhci: Change O2 Host HS200 mode clock frequency to 200MHz
mmc: sdhci: Add support for O2 eMMC HS200 mode
mmc: tegra: Add and use tegra_sdhci_get_max_clock()
mmc: sdhci-esdhc-imx: fix indent
mmc: sdhci-esdhc-imx: disable clocks before changing frequency
mmc: tegra: prevent ACMD23 on Tegra 3
...
Haishuang Yan [Sat, 18 Aug 2018 14:43:48 +0000 (22:43 +0800)]
ip6_vti: simplify stats handling in vti6_xmit
Same as ip_vti, use iptunnel_xmit_stats to updates stats in tunnel xmit
code path.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 18 Aug 2018 19:30:42 +0000 (12:30 -0700)]
pcmcia: remove long deprecated pcmcia_request_exclusive_irq() function
This function was created as a deprecated fallback case back in 2010 by
commit
eb14120f743d ("pcmcia: re-work pcmcia_request_irq()") for legacy
cases.
Actual in-kernel users haven't been around for a long while. The last
in-kernel user was apparently removed four years ago by commit
5f5316fcd08e ("am2150: Update nmclan_cs.c to use update PCMCIA API").
Just remove it entirely.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 18 Aug 2018 19:19:56 +0000 (12:19 -0700)]
deprecate the '__deprecated' attribute warnings entirely and for good
We haven't had lots of deprecation warnings lately, but the rdma use of
it made them flare up again.
They are not useful. They annoy everybody, and nobody ever does
anything about them, because it's always "somebody elses problem". And
when people start thinking that warnings are normal, they stop looking
at them, and the real warnings that mean something go unnoticed.
If you want to get rid of a function, just get rid of it. Convert every
user to the new world order.
And if you can't do that, then don't annoy everybody else with your
marking that says "I couldn't be bothered to fix this, so I'll just spam
everybody elses build logs with warnings about my laziness".
Make a kernelnewbies wiki page about things that could be cleaned up,
write a blog post about it, or talk to people on the mailing lists. But
don't add warnings to the kernel build about cleanup that you think
should happen but you aren't doing yourself.
Don't. Just don't.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 18 Aug 2018 18:44:53 +0000 (11:44 -0700)]
Merge tag 'driver-core-4.19-rc1' of git://git./linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here are all of the driver core and related patches for 4.19-rc1.
Nothing huge here, just a number of small cleanups and the ability to
now stop the deferred probing after init happens.
All of these have been in linux-next for a while with only a merge
issue reported"
* tag 'driver-core-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (21 commits)
base: core: Remove WARN_ON from link dependencies check
drivers/base: stop new probing during shutdown
drivers: core: Remove glue dirs from sysfs earlier
driver core: remove unnecessary function extern declare
sysfs.h: fix non-kernel-doc comment
PM / Domains: Stop deferring probe at the end of initcall
iommu: Remove IOMMU_OF_DECLARE
iommu: Stop deferring probe at end of initcalls
pinctrl: Support stopping deferred probe after initcalls
dt-bindings: pinctrl: add a 'pinctrl-use-default' property
driver core: allow stopping deferred probe after init
driver core: add a debugfs entry to show deferred devices
sysfs: Fix internal_create_group() for named group updates
base: fix order of OF initialization
linux/device.h: fix kernel-doc notation warning
Documentation: update firmware loader fallback reference
kobject: Replace strncpy with memcpy
drivers: base: cacheinfo: use OF property_read_u32 instead of get_property,read_number
kernfs: Replace strncpy with memcpy
device: Add #define dev_fmt similar to #define pr_fmt
...
Linus Torvalds [Sat, 18 Aug 2018 18:04:51 +0000 (11:04 -0700)]
Merge tag 'char-misc-4.19-rc1' of git://git./linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
Linus Torvalds [Sat, 18 Aug 2018 18:00:00 +0000 (11:00 -0700)]
Merge tag 'staging-4.19-rc1' of git://git./linux/kernel/git/gregkh/staging
Pull staging and IIO updates from Greg KH:
"Here are the big staging/iio patches for 4.19-rc1.
Lots of churn here, with tons of cleanups happening in staging
drivers, a removal of an old crypto driver that no one was using
(skein), and the addition of some new IIO drivers. Also added was a
"gasket" driver from Google that needs loads of work and the erofs
filesystem.
Even with adding all of the new drivers and a new filesystem, we are
only adding about 1000 lines overall to the kernel linecount, which
shows just how much cleanup happened, and how big the unused crypto
driver was.
All of these have been in the linux-next tree for a while now with no
reported issues"
* tag 'staging-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (903 commits)
staging:rtl8192u: Remove unused macro definitions - Style
staging:rtl8192u: Add spaces around '+' operator - Style
staging:rtl8192u: Remove stale comment - Style
staging: rtl8188eu: remove unused mp_custom_oid.h
staging: fbtft: Add spaces around / - Style
staging: fbtft: Erases some repetitive usage of function name - Style
staging: fbtft: Adjust some empty-line problems - Style
staging: fbtft: Removes one nesting level to help readability - Style
staging: fbtft: Changes gamma table to define.
staging: fbtft: A bit more information on dev_err.
staging: fbtft: Fixes some alignment issues - Style
staging: fbtft: Puts macro arguments in parenthesis to avoid precedence issues - Style
staging: rtl8188eu: remove unused array dB_Invert_Table
staging: rtl8188eu: remove whitespace, add missing blank line
staging: rtl8188eu: use is_multicast_ether_addr in rtw_sta_mgt.c
staging: rtl8188eu: remove whitespace - style
staging: rtl8188eu: cleanup block comment - style
staging: rtl8188eu: use is_multicast_ether_addr in rtl8188eu_xmit.c
staging: rtl8188eu: use is_multicast_ether_addr in recv_linux.c
staging: rtlwifi: refactor rtl_get_tcb_desc
...
Linus Torvalds [Sat, 18 Aug 2018 17:50:41 +0000 (10:50 -0700)]
Merge tag 'tty-4.19-rc1' of git://git./linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big tty and serial driver pull request for 4.19-rc1.
It's not all that big, just a number of small serial driver updates
and fixes, along with some better vt handling for unicode characters
for those using braille terminals.
All of these patches have been in linux-next for a long time with no
reported issues"
* tag 'tty-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (73 commits)
tty: serial: 8250: Revert NXP SC16C2552 workaround
serial: 8250_exar: Read INT0 from slave device, too
tty: rocket: Fix possible buffer overwrite on register_PCI
serial: 8250_dw: Add ACPI support for uart on Broadcom SoC
serial: 8250_dw: always set baud rate in dw8250_set_termios
dt-bindings: serial: Add binding for uartlite
tty: serial: uartlite: Add support for suspend and resume
tty: serial: uartlite: Add clock adaptation
tty: serial: uartlite: Add structure for private data
serial: sh-sci: Improve support for separate TEI and DRI interrupts
serial: sh-sci: Remove SCIx_RZ_SCIFA_REGTYPE
serial: sh-sci: Allow for compressed SCIF address
serial: sh-sci: Improve interrupts description
serial: 8250: Use cached port name directly in messages
serial: 8250_exar: Drop unused variable in pci_xr17v35x_setup()
vt: drop unused struct vt_struct
vt: avoid a VLA in the unicode screen scroll function
vt: add /dev/vcsu* to devices.txt
vt: coherence validation code for the unicode screen buffer
vt: selection: take screen contents from uniscr if available
...
Linus Torvalds [Sat, 18 Aug 2018 17:21:49 +0000 (10:21 -0700)]
Merge tag 'usb-4.19-rc1' of git://git./linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB and phy driver patch set for 4.19-rc1.
Nothing huge but there was a lot of work that happened this
development cycle:
- lots of type-c work, with drivers graduating out of staging, and
displayport support being added.
- new PHY drivers
- the normal collection of gadget driver updates and fixes
- code churn to work on the urb handling path, using irqsave()
everywhere in anticipation of making this codepath a lot simpler in
the future.
- usbserial driver fixes and reworks
- other misc changes
All of these have been in linux-next with no reported issues for a
while"
* tag 'usb-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (159 commits)
USB: serial: pl2303: add a new device id for ATEN
usb: renesas_usbhs: Kconfig: convert to SPDX identifiers
usb: dwc3: gadget: Check MaxPacketSize from descriptor
usb: dwc2: Turn on uframe_sched on "stm32f4x9_fsotg" platforms
usb: dwc2: Turn on uframe_sched on "amlogic" platforms
usb: dwc2: Turn on uframe_sched on "his" platforms
usb: dwc2: Turn on uframe_sched on "bcm" platforms
usb: dwc2: gadget: ISOC's starting flow improvement
usb: dwc2: Make dwc2_readl/writel functions endianness-agnostic.
usb: dwc3: core: Enable AutoRetry feature in the controller
usb: dwc3: Set default mode for dwc_usb31
usb: gadget: udc: renesas_usb3: Add register of usb role switch
usb: dwc2: replace ioread32/iowrite32_rep with dwc2_readl/writel_rep
usb: dwc2: Modify dwc2_readl/writel functions prototype
usb: dwc3: pci: Intel Merrifield can be host
usb: dwc3: pci: Supply device properties via driver data
arm64: dts: dwc3: description of incr burst type
usb: dwc3: Enable undefined length INCR burst type
usb: dwc3: add global soc bus configuration reg0
usb: dwc3: Describe 'wakeup_work' field of struct dwc3_pci
...
David S. Miller [Sat, 18 Aug 2018 17:02:49 +0000 (10:02 -0700)]
Merge git://git./pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2018-08-18
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a BPF selftest failure in test_cgroup_storage due to rlimit
restrictions, from Yonghong.
2) Fix a suspicious RCU rcu_dereference_check() warning triggered
from removing a device's XDP memory allocator by using the correct
rhashtable lookup function, from Tariq.
3) A batch of BPF sockmap and ULP fixes mainly fixing leaks and races
as well as enforcing module aliases for ULPs. Another fix for BPF
map redirect to make them work again with tail calls, from Daniel.
4) Fix XDP BPF samples to unload their programs upon SIGTERM, from Jesper.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 18 Aug 2018 16:59:19 +0000 (09:59 -0700)]
Merge git://git./pub/scm/linux/kernel/git/pablo/nf
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree:
1) Infinite loop in IPVS when net namespace is released, from
Tan Hu.
2) Do not show negative timeouts in ip_vs_conn by using the new
jiffies_delta_to_msecs(), patches from Matteo Croce.
3) Set F_IFACE flag for linklocal addresses in ip6t_rpfilter,
from Florian Westphal.
4) Fix overflow in set size allocation, from Taehee Yoo.
5) Use netlink_dump_start() from ctnetlink to fix memleak from
the error path, again from Florian.
6) Register nfnetlink_subsys in last place, otherwise netns
init path may lose race and see net->nft uninitialized data.
This also reverts previous attempt to fix this by increase
netns refcount, patches from Florian.
7) Remove conntrack entries on layer 4 protocol tracker module
removal, from Florian.
8) Use GFP_KERNEL_ACCOUNT for xtables blob allocation, from
Michal Hocko.
9) Get tproxy documentation in sync with existing codebase,
from Mate Eckl.
10) Honor preset layer 3 protocol via ctx->family in the new nft_ct
timeout infrastructure, from Harsha Sharma.
11) Let uapi nfnetlink_osf.h compile standalone with no errors,
from Dmitry V. Levin.
12) Missing braces compilation warning in nft_tproxy, patch from
Mate Eclk.
13) Disregard bogus check to bail out on non-anonymous sets from
the dynamic set update extension.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 18 Aug 2018 00:27:58 +0000 (17:27 -0700)]
Merge tag '9p-for-4.19-2' of git://github.com/martinetd/linux
Pull 9p updates from Dominique Martinet:
"This contains mostly fixes (6 to be backported to stable) and a few
changes, here is the breakdown:
- rework how fids are attributed by replacing some custom tracking in
a list by an idr
- for packet-based transports (virtio/rdma) validate that the packet
length matches what the header says
- a few race condition fixes found by syzkaller
- missing argument check when NULL device is passed in sys_mount
- a few virtio fixes
- some spelling and style fixes"
* tag '9p-for-4.19-2' of git://github.com/martinetd/linux: (21 commits)
net/9p/trans_virtio.c: add null terminal for mount tag
9p/virtio: fix off-by-one error in sg list bounds check
9p: fix whitespace issues
9p: fix multiple NULL-pointer-dereferences
fs/9p/xattr.c: catch the error of p9_client_clunk when setting xattr failed
9p: validate PDU length
net/9p/trans_fd.c: fix race by holding the lock
net/9p/trans_fd.c: fix race-condition by flushing workqueue before the kfree()
net/9p/virtio: Fix hard lockup in req_done
net/9p/trans_virtio.c: fix some spell mistakes in comments
9p/net: Fix zero-copy path in the 9p virtio transport
9p: Embed wait_queue_head into p9_req_t
9p: Replace the fidlist with an IDR
9p: Change p9_fid_create calling convention
9p: Fix comment on smp_wmb
net/9p/client.c: version pointer uninitialized
fs/9p/v9fs.c: fix spelling mistake "Uknown" -> "Unknown"
net/9p: fix error path of p9_virtio_probe
9p/net/protocol.c: return -ENOMEM when kmalloc() failed
net/9p/client.c: add missing '\n' at the end of p9_debug()
...
Linus Torvalds [Fri, 17 Aug 2018 23:49:31 +0000 (16:49 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge updates from Andrew Morton:
- a few misc things
- a few Y2038 fixes
- ntfs fixes
- arch/sh tweaks
- ocfs2 updates
- most of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (111 commits)
mm/hmm.c: remove unused variables align_start and align_end
fs/userfaultfd.c: remove redundant pointer uwq
mm, vmacache: hash addresses based on pmd
mm/list_lru: introduce list_lru_shrink_walk_irq()
mm/list_lru.c: pass struct list_lru_node* as an argument to __list_lru_walk_one()
mm/list_lru.c: move locking from __list_lru_walk_one() to its caller
mm/list_lru.c: use list_lru_walk_one() in list_lru_walk_node()
mm, swap: make CONFIG_THP_SWAP depend on CONFIG_SWAP
mm/sparse: delete old sparse_init and enable new one
mm/sparse: add new sparse_init_nid() and sparse_init()
mm/sparse: move buffer init/fini to the common place
mm/sparse: use the new sparse buffer functions in non-vmemmap
mm/sparse: abstract sparse buffer allocations
mm/hugetlb.c: don't zero 1GiB bootmem pages
mm, page_alloc: double zone's batchsize
mm/oom_kill.c: document oom_lock
mm/hugetlb: remove gigantic page support for HIGHMEM
mm, oom: remove sleep from under oom_lock
kernel/dma: remove unsupported gfp_mask parameter from dma_alloc_from_contiguous()
mm/cma: remove unsupported gfp_mask parameter from cma_alloc()
...
Colin Ian King [Fri, 17 Aug 2018 22:50:07 +0000 (15:50 -0700)]
mm/hmm.c: remove unused variables align_start and align_end
Variables align_start and align_end are being assigned but are never
used hence they are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'align_start' set but not used [-Wunused-but-set-variable]
warning: variable 'align_size' set but not used [-Wunused-but-set-variable]
Link: http://lkml.kernel.org/r/20180714161124.3923-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Colin Ian King [Fri, 17 Aug 2018 22:50:01 +0000 (15:50 -0700)]
fs/userfaultfd.c: remove redundant pointer uwq
Pointer uwq is being assigned but is never used hence it is redundant
and can be removed.
Cleans up clang warning:
warning: variable 'uwq' set but not used [-Wunused-but-set-variable]
Link: http://lkml.kernel.org/r/20180717090802.18357-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / openwrt / staging / blogic.git / log