mlxsw: spectrum_router: Add GRE tunnel support for Spectrum-2

Spectrum-2 GRE tunnel implementation requires a specific underlay RIF that
points to the virtual router used for forwarding the encapsulated packet.

Add Spectrum-2 specific loopback router interface creation methods which
may create or reuse the dedicated underlay RIF.

Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: spectrum_router: Update tunnel decap properties

Spectrum-2 requires to specify the egress RIF when setting tunnel decap
properties. Add a method for accessing the underlay RIF index and then use
it when setting decap properties.

Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: spectrum_router: Support RIF without device

Spectrum-2 underlay RIF is merely an auxiliary RIF that points to the
virtual router used for encapsulated packets lookup. It exists only when
its overlay RIF exists but may be shared with other overlay RIFs.
Hence it is undesired to mark any device as related to it.

Therefore allow usage of NULL device when allocating RIF.

Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: spectrum_router: Change mlxsw_sp_ipip_lb_ul_vr_id()

For the sake of Spectrum-2 GRE support, as ul_vr_id field is reserved for
Spectrum-2, Change mlxsw_sp_ipip_lb_ul_vr_id() implementation not to use
the reserved field.

Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: spectrum_router: Add underlay RIF ID support

Spectrum-2 GRE tunnels underlay should be given not only the virtual router
information for an encapsulated packet lookup, but also an underlay RIF
object which belongs to a virtual router.

Therefore add ul_rif_id field in struct mlxsw_sp_rif_ipip_lb, to be used
later in Spectrum-2 underlay RIF implementation. This field complements
ul_vr_id field, already present and defined as reserved for Spectrum-2.

Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: spectrum_router: Mark RIF index as taken before creation

The presence of an allocated RIF in mlxsw_sp->router->rifs[rif_index] marks
that rif_index as taken.
Set the marking of a taken RIF to happen before calling ops->create in
order to allow creation of a GRE underlay RIF, which may be allocated and
created as part of an overlay RIF creation.

Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: spectrum_router: Adjust loopback RIF configuration

In Spectrum-2, the underlay routing table is pointed by an underlay router
interface in contrary to Spectrum where only an underlay virtual router
should be set. That makes the underlay virtual router field in RITR
reserved for Spectrum-2.

Change loopback RIF creation function to support the new underlay RIF
field, however leave this field reserved for Spectrum-1 updates.

Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: spectrum: Set RIF ops per ASIC type

Set RIF ops array as member of mlxsw_sp in order to control which RIF
operations callbacks are called per ASIC type. This is needed to control
per ASIC handling of loopback RIF configurations.

Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: spectrum_router: Split RIF ops array for Spectrum-2 support

Split RIF ops array for Spectrum-1 and Spectrum-2 callbacks in order to
support different sets of operations for loopback RIF handling, as
underlying implementation differs between the ASICs.

Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: reg: Add underlay egress RIF field in RTDP register

In Spectrum-2 we need to specify the underlay egress router interface
when performing IP-in-IP and NVE packet decapsulation in the underlay
router.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: reg: Add fields to RITR - Router Interface Table Register

Add fields relevant for Spectrum-2 Loopback IPinIP router interface
creation. Add additional Loopback RIF protocol value - Generic, used for
creation of an explicit underlay RIF, and also add a field named
underlay_rif used for specifying the underlay RIF of a tunnel.

Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'r8169-series-with-smaller-improvements'

Heiner Kallweit says:

====================
r8169: series with smaller improvements

Series with smaller improvements.

v2:
- fixed a small copy & paste error in patch 4
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: factor out getting ether_clk

rtl_init_one() is complex enough, so we better factor out getting the
ether_clk.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: replace mii_bus member with phy_device member in struct rtl8169_private

Accessing the phy_device indirectly via the netdevice causes few issues:
- Accessing the phy_device when it's not attached may cause a NPE.
- If we have to access the phy_device when it's not attached we have
  to use mdiobus_get_phy() to get a reference to the phy_device.

Therefore store a phy_device reference in struct rtl8169_private directly.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: reset chip synchronously in __rtl8169_resume

Triggering an asynchronous reset is problematic for the following
reasons, therefore reset the chip synchronously.

- The reset routine resets registers and parameters behind our back
  what may collide with code executed after triggering the reset.

- __rtl8169_resume() is called as part of pm_runtime_get_sync() and
  callers expect that the chip is fully resumed afterwards.

In context of this driver triggering an asynchonous reset should be
considered an emergency procedure.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: add helpers for locking / unlocking the config registers

Add helpers for locking / unlocking the config registers.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: improve rtl_pcie_state_l2l3_enable

All calls to this function have the enable parameter set to false.
So we can replace the function with a disable-only version.

v2:
- fixed copy & paste error

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: initialize task workqueue only once

It's sufficient to initialize the workqueue once, therefore remove the
additional initialization whenever rtl_open() is called.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: remove unneeded call in pcierr

rtl8169_hw_reset() is called as part of the reset routine which is
scheduled in the line after. So we can remove the call to
rtl8169_hw_reset() here.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: remove rtl_get_events

This helper is used only once, so remove it.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net_sched: add performance counters for basic filter

Similar to u32 filter, it is useful to know how many times
we reach each basic filter and how many times we pass the
ematch attached to it.

Sample output:

filter protocol arp pref 49152 basic chain 0
filter protocol arp pref 49152 basic chain 0 handle 0x1  (rule hit 3 success 3)
action order 1: gact action pass
 random type none pass val 0
 index 1 ref 1 bind 1 installed 81 sec used 4 sec
Action statistics:
Sent 126 bytes 3 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sock: do not set sk_cookie in sk_clone_lock()

The only call site of sk_clone_lock is in inet_csk_clone_lock,
and sk_cookie will be set there.
So we don't need to set sk_cookie in sk_clone_lock().

Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

isdn: remove unneeded semicolon

remove unneeded semicolon

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: usb: rtl8150: remove set but not used variable 'rx_stat'

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/usb/rtl8150.c: In function 'read_bulk_callback':
drivers/net/usb/rtl8150.c:391:6: warning:
 variable 'rx_stat' set but not used [-Wunused-but-set-variable]

Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'dpaa2-eth-add-debugfs-statistics'

Ioana Ciornei says:

====================
dpaa2-eth: add debugfs statistics

This patch set exports detailed driver counters through debugfs.
Counters which are already available through ethtool are now
presented in a structured manner (per-core, per-FQ and
per-channel) in debugfs.

The first patch is changing the dpaa2_eth_queue_count into a macro
(in order to avoid a warning) while the second one is adding the
debugfs support.

Changes in v2:
  - remove the _exit annotation of dpaa2_eth_dbg_exit
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

dpaa2-eth: add debugfs statistics

Export detailed driver counters through debugfs.

Statistics already available in ethtool are presented in a
structured manner. Includes per-core, per-FQ and per-channel statistics.

Also transition from module_fsl_mc_driver to explicit module_init/exit
in order to create the debugfs directory besides registering the driver.

Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dpaa2-eth: transform dpaa2_eth_queue_count into a macro

Transform dpaa2_eth_queue_count into a macro to follow the
the convention used by dpaa2_eth_fs_count and other functions.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'net-use-strict-checks-in-doit-handlers'

Jakub Kicinski says:

====================
net: use strict checks in doit handlers

This series extends strict argument checking to doit handlers
of the GET* nature.  This is a bit tricky since strict checking
flag has already been released..

iproute2 did not have a release with strick checks enabled,
and it will only need a minor one-liner to pass strick checks
after all the work that DaveA has already done.

Big thanks to Dave Ahern for help and guidence.

v2:
 - remove unnecessary check in patch 5 (Nicolas);
 - add path 7 (DaveA);
 - improve messages in patch 8 (DaveA).
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: mpls: netconf: perform strict checks also for doit handlers

Make RTM_GETNETCONF's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mpls: route: perform strict checks also for doit handlers

Make RTM_GETROUTE's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ipv6: route: perform strict checks also for doit handlers

Make RTM_GETROUTE's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ipv6: addrlabel: perform strict checks also for doit handlers

Make RTM_GETADDRLABEL's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ipv6: netconf: perform strict checks also for doit handlers

Make RTM_GETNETCONF's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ipv6: addr: perform strict checks also for doit handlers

Make RTM_GETADDR's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ipv4: ipmr: perform strict checks also for doit handlers

Make RTM_GETROUTE's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.

v2: - improve extack messages (DaveA).

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ipv4: route: perform strict checks also for doit handlers

Make RTM_GETROUTE's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.

v2: - new patch (DaveA).

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ipv4: netconf: perform strict checks also for doit handlers

Make RTM_GETNETCONF's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: namespace: perform strict checks also for doit handlers

Make RTM_GETNSID's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.

v2: - don't check size >= sizeof(struct rtgenmsg) (Nicolas).

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rtnetlink: ifinfo: perform strict checks also for doit handler

Make RTM_GETLINK's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rtnetlink: stats: reject requests for unknown stats

In the spirit of strict checks reject requests of stats the kernel
does not support when NETLINK_F_STRICT_CHK is set.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rtnetlink: stats: validate attributes in get as well as dumps

Make sure NETLINK_GET_STRICT_CHK influences both GETSTATS doit
as well as the dump.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: netlink: add helper to retrieve NETLINK_F_STRICT_CHK

Dumps can read state of the NETLINK_F_STRICT_CHK flag from
a field in the callback structure.  For non-dump GET requests
we need a way to access the state of that flag from a socket.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

virtio-net: per-queue RPS config

On multiqueue network devices, RPS maps are configured independently
for each receive queue through /sys/class/net/$DEV/queues/rx-*.

On virtio-net currently all packets use the map from rx-0, because the
real rx queue is not known at time of map lookup by get_rps_cpu.

Call skb_record_rx_queue in the driver rx path to make lookup work.

Recording the receive queue has ramifications beyond RPS, such as in
sticky load balancing decisions for sockets (skb_tx_hash) and XPS.

Reported-by: Mark Hlady <mhlady@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sch_api: Change signature of qdisc_tree_reduce_backlog() to use ints

There are now several places where qdisc_tree_reduce_backlog() is called
with a negative number of packets (to signal an increase in number of
packets in the queue). Rather than rely on overflow behaviour, change the
function signature to use signed integers to communicate this usage to
people reading the code.

Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'hns3-fixes'

Huazhong Tan says:

====================
net: hns3: code optimizations & bugfixes for HNS3 driver

This patchset includes bugfixes and code optimizations for the HNS3
ethernet controller driver
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add HNAE3_RESTORE_CLIENT interface in enet module

The HNAE3_INIT_CLIENT interface is also used when changing tc
configuration, vlan/mac hardware table does not need to be restored
when tc configuration changes.

This patch adds a HNAE3_RESTORE_CLIENT interface to restore the
vlan/mac hardware table when resetting.

Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: do reinitialization while ETS configuration changed

When the ETS information is changed, the network device needs to be
re-initialized, otherwise the information such as the receiving queue
will be incorrect.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix wrong combined count returned by ethtool -l

The current code returns the number of all queues that can be used and
the number of queues that have been allocated, which is incorrect.
What should be returned is the number of queues allocated for each enabled
TC and the number of queues that can be allocated.

This patch fixes it.

Fixes: 482d2e9c1cc7 ("net: hns3: add support to query tqps number")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: adjust the use of alloc_tqps and num_tqps

The alloc_tqps field of struct hclge_vport represents the total number
of tqps allocated to the vport. The num_tqps of struct
hnae3_knic_private_info indicates the total number of all enabled tqps,
which needs to be distinguished during use.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: fix user configuration loss for ethtool -L

Ethtool -L option with the combined parameter is for changing the number of
multi-purpose channels of the specified network device. Under the current
scheme, the user configuration information will be lost after the reset or
TC information changed.

This patch fixes this issue. By default, this configuration is set to the
minimum between the number of queues for each enabled TCs and the maximum
number support available in the hardware. When there is a user
configuration, regardless of the reset or TC information change, it should
keep the user's configuration while it is under the hardware limits,
otherwise set to the maximum number support available in the hardware.

Fixes: 09f2af6405b8 ("net: hns3: add support to modify tqps number")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: remove redundant codes in hclge_knic_setup

The TC info will be updated in hclge_tm_vport_tc_info_update(),
so hclge_knic_setup() no need to do it again.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: modify parameter checks in the hns3_set_channels

The number of queues for each enabled TC should range from 1 to
the maximum available value, and return directly if the value
is same as the current one.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: add interface hclge_tm_bp_setup

Provide a common interface to complete the back pressure settings
of all enabled TCs. So other functions directly call this interface
to complete the corresponding operation.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: reuse reinitialization interface in the hns3_set_channels

There is already common interface for network device reinitialization,
so hns3_set_channels() should just call them.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: remove unnecessary hns3_adjust_tqps_num

The parameter passed to hns3_set_channels() are already the number of
queues per channel of the enabled TC, so it is not need to divide
the number of enabled TCs.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: remove unused member in struct hns3_enet_ring

The irq_init_flag field in struct hns3_enet_ring is unnecessary.
This patch removes it.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns3: modify enet reinitialization interface

hns3_reset_notify_init_enet and hns3_reset_notify_uninit_enet are the
reinitialization interface that will be called when the device reset,
the number of TC changed, or the queue length changed. So these two
function should call hns3_get_ring_config() and hns3_put_ring_config()
to allocate and free memory for the ring with the correct number.

Also this patch fixes a double free problem when
hns3_reset_notify_uninit_enet calling hns3_nic_dealloc_vector_data

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'Devlink-health-reporting-and-recovery-system'

Eran Ben Elisha says:

====================
Devlink health reporting and recovery system

The health mechanism is targeted for Real Time Alerting, in order to know when
something bad had happened to a PCI device
- Provide alert debug information
- Self healing
- If problem needs vendor support, provide a way to gather all needed debugging
  information.

The main idea is to unify and centralize driver health reports in the
generic devlink instance and allow the user to set different
attributes of the health reporting and recovery procedures.

The devlink health reporter:
Device driver creates a "health reporter" per each error/health type.
Error/Health type can be a known/generic (eg pci error, fw error, rx/tx error)
or unknown (driver specific).
For each registered health reporter a driver can issue error/health reports
asynchronously. All health reports handling is done by devlink.
Device driver can provide specific callbacks for each "health reporter", e.g.
 - Recovery procedures
 - Diagnostics and object dump procedures
 - OOB initial attributes
Different parts of the driver can register different types of health reporters
with different handlers.

Once an error is reported, devlink health will do the following actions:
  * A log is being send to the kernel trace events buffer
  * Health status and statistics are being updated for the reporter instance
  * Object dump is being taken and saved at the reporter instance (as long as
    there is no other dump which is already stored)
  * Auto recovery attempt is being done. Depends on:
    - Auto-recovery configuration
    - Grace period vs. time passed since last recover

The user interface:
User can access/change each reporter attributes and driver specific callbacks
via devlink, e.g per error type (per health reporter)
 - Configure reporter's generic attributes (like: Disable/enable auto recovery)
 - Invoke recovery procedure
 - Run diagnostics
 - Object dump

The devlink health interface (via netlink):
DEVLINK_CMD_HEALTH_REPORTER_GET
  Retrieves status and configuration info per DEV and reporter.
DEVLINK_CMD_HEALTH_REPORTER_SET
  Allows reporter-related configuration setting.
DEVLINK_CMD_HEALTH_REPORTER_RECOVER
  Triggers a reporter's recovery procedure.
DEVLINK_CMD_HEALTH_REPORTER_DIAGNOSE
  Retrieves diagnostics data from a reporter on a device.
DEVLINK_CMD_HEALTH_REPORTER_DUMP_GET
  Retrieves the last stored dump. Devlink health
  saves a single dump. If an dump is not already stored by the devlink
  for this reporter, devlink generates a new dump.
  dump output is defined by the reporter.
DEVLINK_CMD_HEALTH_REPORTER_DUMP_CLEAR
  Clears the last saved dump file for the specified reporter.

                                               netlink
                                      +--------------------------+
                                      |                          |
                                      |            +             |
                                      |            |             |
                                      +--------------------------+
                                                   |request for ops
                                                   |(diagnose,
 mlx5_core                             devlink     |recover,
                                                   |dump)
+--------+                            +--------------------------+
|        |                            |    reporter|             |
|        |                            |  +---------v----------+  |
|        |   ops execution            |  |                    |  |
|     <----------------------------------+                    |  |
|        |                            |  |                    |  |
|        |                            |  + ^------------------+  |
|        |                            |    | request for ops     |
|        |                            |    | (recover, dump)     |
|        |                            |    |                     |
|        |                            |  +-+------------------+  |
|        |     health report          |  | health handler     |  |
|        +------------------------------->                    |  |
|        |                            |  +--------------------+  |
|        |     health reporter create |                          |
|        +---------------------------->                          |
+--------+                            +--------------------------+

In this patchset, mlx5e TX reporter is implemented.

v2:
- Remove FW* reporters to decrease the amount of patches in the patchset
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

devlink: Add Documentation/networking/devlink-health.txt

This patch adds a new file to add information about devlink health
mechanism.

Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx5e: Add TX timeout support for mlx5e TX reporter

With this patch, ndo_tx_timeout callback will be redirected to the TX
reporter in order to detect a TX timeout error and report it to the
devlink health. (The watchdog detects TX timeouts, but the driver verify
the issue still exists before launching any recover method).

In addition, recover from TX timeout in case of lost interrupt was added
to the TX reporter recover method. The TX timeout recover from lost
interrupt is not a new feature in the driver, this patch re-organize the
functionality and move it to the TX reporter recovery flow.

TX timeout example:
(with auto_recover set to false, if set to true, the manual recover and
diagnose sections are irrelevant)

$cat /sys/kernel/debug/tracing/trace
...
devlink_health_report: bus_name=pci dev_name=0000:00:09.0
driver_name=mlx5_core reporter_name=TX: TX timeout on queue: 0, SQ: 0xd8a, CQ:
0x406, SQ Cons: 0x2 SQ Prod: 0x2, usecs since last trans: 13972000

$devlink health diagnose pci/0000:00:09 reporter TX
SQ 0xd8a: HW state: 1, stopped: 1
SQ 0xe44: HW state: 1, stopped: 0
SQ 0xeb4: HW state: 1, stopped: 0
SQ 0xf1f: HW state: 1, stopped: 0
SQ 0xf80: HW state: 1, stopped: 0
SQ 0xfe5: HW state: 1, stopped: 0

$devlink health recover pci/0000:00:09 reporter TX
$devlink health show
pci/0000:00:09.0:
  name TX state healthy #err 1 #recover 1 last_dump_ts N/A dump_available false
    attributes:
        grace_period 500 auto_recover false

Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx5e: Add TX reporter support

Add mlx5e tx reporter to devlink health reporters. This reporter will be
responsible for diagnosing, reporting and recovering of TX errors.
This patch declares the TX reporter operations and allocate it using the
devlink health API. Currently, this reporter supports reporting and
recovering from send error CQE only. In addition, it adds diagnose
information for the open SQs.

For a local SQ recover (due to driver error report), in case of SQ recover
failure, the recover operation will be considered as a failure.
For a full TX recover, an attempt to close and open the channels will be
done. If this one passed successfully, it will be considered as a
successful recover.

The SQ recover from error CQE flow is not a new feature in the driver,
this patch re-organize the functions and adapt them for the devlink
health API. For this purpose, move code from en_main.c to a new file
named reporter_tx.c.

Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

devlink: Add health dump {get,clear} commands

Add devlink health dump commands, in order to run an dump operation
over a specific reporter.

The supported operations are dump_get in order to get last saved
dump (if not exist, dump now) and dump_clear to clear last saved
dump.

It is expected from driver's callback for diagnose command to fill it
via the buffer descriptors API. Devlink will parse it and convert it to
netlink nla API in order to pass it to the user.

Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

devlink: Add health diagnose command

Add devlink health diagnose command, in order to run a diagnose
operation over a specific reporter.

It is expected from driver's callback for diagnose command to fill it
via the buffer descriptors API. Devlink will parse it and convert it to
netlink nla API in order to pass it to the user.

Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

devlink: Add health recover command

Add devlink health recover command to the uapi, in order to allow the user
to execute a recover operation over a specific reporter.

Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

devlink: Add health set command

Add devlink health set command, in order to set configuration parameters
for a specific reporter.
Supported parameters are:
- graceful_period: Time interval between auto recoveries (in msec)
- auto_recover: Determines if the devlink shall execute recover upon
receiving error for the reporter

Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

devlink: Add health get command

Add devlink health get command to provide reporter/s data for user space.
Add the ability to get data per reporter or dump data from all available
reporters.

Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

devlink: Add health report functionality

Upon error discover, every driver can report it to the devlink health
mechanism via devlink_health_report function, using the appropriate
reporter registered to it. Driver can pass error specific context which
will be delivered to it as part of the dump / recovery callbacks.

Once an error is reported, devlink health will do the following actions:
* A log is being send to the kernel trace events buffer
* Health status and statistics are being updated for the reporter instance
* Object dump is being taken and stored at the reporter instance (as long
  as there is no other dump which is already stored)
* Auto recovery attempt is being done. depends on:
  - Auto Recovery configuration
  - Grace period vs. time since last recover

Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

devlink: Add health reporter create/destroy functionality

Devlink health reporter is an instance for reporting, diagnosing and
recovering from run time errors discovered by the reporters.
Define it's data structure and supported operations.
In addition, expose devlink API to create and destroy a reporter.
Each devlink instance will hold it's own reporters list.

As part of the allocation, driver shall provide a set of callbacks which
will be used the devlink in order to handle health reports and user
commands related to this reporter. In addition, driver is entitled to
provide some priv pointer, which can be fetched from the reporter by
devlink_health_reporter_priv function.

For each reporter, devlink will hold a metadata of statistics,
buffers and status.

Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

devlink: Add health buffer support

Devlink health buffer is a mechanism to pass descriptors between drivers
and devlink. The API allows the driver to add objects, object pair,
value array (nested attributes), value and name.

Driver can use this API to fill the buffers in a format which can be
translated by the devlink to the netlink message.

In order to fulfill it, an internal buffer descriptor is defined. This
will hold the data and metadata per each attribute and by used to pass
actual commands to the netlink.

This mechanism will be later used in devlink health for dump and diagnose
data store by the drivers.

Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net_sched: add hit counter for matchall

Although matchall always matches packets, however, it still
relies on a protocol match first. So it is still useful to have
such a counter for matchall. Of course, unlike u32, every time
we hit a matchall filter, it is always a success, so we don't
have to distinguish them.

Sample output:

filter protocol 802.1Q pref 100 matchall chain 0
filter protocol 802.1Q pref 100 matchall chain 0 handle 0x1
  not_in_hw (rule hit 10)
action order 1: vlan  pop continue
 index 1 ref 1 bind 1 installed 40 sec used 1 sec
Action statistics:
Sent 836 bytes 10 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0

Reported-by: Martin Olsson <martin.olsson+netdev@sentorsecurity.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'phy-improve-stopping-PHY'

Heiner Kallweit says:

====================
net: phy: improve stopping PHY

This patchset improves and simplifies stopping the PHY.

Heiner Kallweit (3):
  net: phy: stop PHY if needed when entering phy_disconnect
  net: phy: ensure phylib state machine is stopped after calling phy_stop
  net: phy: remove phy_stop_interrupts

v2:
- break down the patch to a patchset
v3:
- don't warn if driver didn't call phy_stop before phy_disconnect
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: remove phy_stop_interrupts

Interrupts have been disabled in phy_stop() already. So we can remove
phy_stop_interrupts() and free the interrupt in phy_disconnect()
directly.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: ensure phylib state machine is stopped after calling phy_stop

The call to the phylib state machine in phy_stop() just ensures that
the state machine isn't re-triggered, but a state machine call may
be scheduled already. So lets's call phy_stop_machine().
This also allows to get rid of the call to phy_stop_machine() in
phy_disconnect().

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: stop PHY if needed when entering phy_disconnect

Stop PHY if needed when entering phy_disconnect. This allows drivers
that don't need a separate call to phy_stop() to omit this call.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: declare tcp_mmap() only when CONFIG_MMU is set

Since tcp_mmap() is defined when CONFIG_MMU is set.

Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: jme: fix indentation issues

There are two lines that have indentation issues, fix these. Also remove
an empty line.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: vxge: fix indentation issue

There is a goto statement that indented too deeply, fix it.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: improve get_phy_id

Only caller of get_phy_id() is get_phy_device(). There a PHY ID of
0xffffffff is translated back to -ENODEV. So we can avoid some
overhead by returning -ENODEV directly.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: remove state PHY_CHANGELINK

Since recent changes to the phylib state machine state PHY_CHANGELINK
isn't used any longer. Therefore let's remove it.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ip6_gre: remove gre_hdr_len from ip6erspan_rcv

Remove gre_hdr_len from ip6erspan_rcv routine signature since
it is not longer used

Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'tcp_openreq_child'

Eric Dumazet says:

====================
tcp: remove code from tcp_create_openreq_child()

tcp_create_openreq_child() is essentially cloning a listener, then
must initialize some fields that can not be inherited.

Listeners are either fresh sockets, or sockets that came through
tcp_disconnect() after a session that dirtied many fields.

By moving code to tcp_disconnect(), we can shorten time taken
to create a clone, since tcp_disconnect() operation is very
unlikely.
====================

Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: move rx_opt & syn_data_acked init to tcp_disconnect()

If we make sure all listeners have these fields cleared, then a clone
will also inherit zero values.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: move tp->rack init to tcp_disconnect()

If we make sure all listeners have proper tp->rack value,
then a clone will also inherit proper initial value.

Note that fresh sockets init tp->rack from tcp_init_sock()

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: move app_limited init to tcp_disconnect()

If we make sure all listeners have app_limited set to ~0U,
then a clone will also inherit proper initial value.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: move retrans_out, sacked_out, tlp_high_seq, last_oow_ack_time init to tcp_disconnect()

If we make sure all listeners have these fields cleared, then a clone
will also inherit zero values.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: do not clear urg_data in tcp_create_openreq_child

All listeners have this field cleared already, since tcp_disconnect()
clears it and newly created sockets have also a zero value here.

So a clone will inherit a zero value here.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: move snd_cwnd & snd_cwnd_cnt init to tcp_disconnect()

Passive connections can inherit proper value by cloning,
if we make sure all listeners have the proper values there.

tcp_disconnect() was setting snd_cwnd to 2, which seems
quite obsolete since IW10 adoption.

Also remove an obsolete comment.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: move mdev_us init to tcp_disconnect()

If we make sure a listener always has its mdev_us
field set to TCP_TIMEOUT_INIT, we do not need to rewrite
this field after a new clone is created.

tcp_disconnect() is very seldom used in real applications.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: do not clear srtt_us in tcp_create_openreq_child

All listeners have this field cleared already, since tcp_disconnect()
clears it and newly created sockets have also a zero value here.

So a clone will inherit a zero value here.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: do not clear packets_out in tcp_create_openreq_child()

New sockets have this field cleared, and tcp_disconnect()
calls tcp_write_queue_purge() which among other things
also clear tp->packets_out

So a listener is guaranteed to have this field cleared.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: move icsk_rto init to tcp_disconnect()

If we make sure a listener always has its icsk_rto
field set to TCP_TIMEOUT_INIT, we do not need to rewrite
this field after a new clone is created.

tcp_disconnect() is very seldom used in real applications.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: do not set snd_ssthresh in tcp_create_openreq_child()

New sockets get the field set to TCP_INFINITE_SSTHRESH in tcp_init_sock()
In case a socket had this field changed and transitions to TCP_LISTEN
state, tcp_disconnect() also makes sure snd_ssthresh is set to
TCP_INFINITE_SSTHRESH.

So a listener has this field set to TCP_INFINITE_SSTHRESH already.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mlx4: remove unneeded semicolon

Remove unneeded semicolon.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ethernet: ti: cpsw-phy-sel: remove unneeded semicolon

Remove unneeded semicolon.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: remove unneeded semicolon in trace.c

Remove unneeded semicolon

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qed: remove duplicated include from qed_if.h

Remove duplicated include.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sb1000: fix a couple of indentation issues and remove assignment in if statements

There is an if statement and a return statement that are incorrectly
indented. Fix these.  Also replace the assignment-in-if statements
to assignment followed by an if to keep to the coding style.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: add a route cache full diagnostic message

In some testing scenarios, dst/route cache can fill up so quickly
that even an explicit GC call occasionally fails to clean it up. This leads
to sporadically failing calls to dst_alloc and "network unreachable" errors
to the user, which is confusing.

This patch adds a diagnostic message to make the cause of the failure
easier to determine.

Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dpaa2-eth: Fix ndo_stop routine

In the current implementation, on interface down we disabled NAPI and
then manually drained any remaining ingress frames. This could lead
to a situation when, under heavy traffic, the data availability
notification for some of the channels would not get rearmed correctly.

Change the implementation such that we let all remaining ingress frames
be processed as usual and only disable NAPI once the hardware queues
are empty.

We also add a wait on the Tx side, to allow hardware time to process
all in-flight Tx frames before issueing the disable command.

Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

wan: dscc4: fix various indentation issues

There are some lines that have indentation issues, fix these.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>