Manasi Navare [Wed, 28 Nov 2018 20:26:23 +0000 (12:26 -0800)]
drm/i915/dp: Disable DSC in source by disabling DSS CTL bits
1. Disable Left/right VDSC branch in DSS Ctrl reg
depending on the number of VDSC engines being used
2. Disable joiner in DSS Ctrl reg
v4:
* Remove encoder, make crtc_state const (Ville)
v3 (From Manasi):
* Add Disable PG2 for VDSC on eDP
v2 (From Manasi):
* Use old_crtc_state to find dsc params
* Add a condition to disable only if
dsc state compression is enabled
* Use correct DSS CTL regs
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-12-manasi.d.navare@intel.com
Manasi Navare [Wed, 28 Nov 2018 20:26:22 +0000 (12:26 -0800)]
drm/i915/dp: Configure Display stream splitter registers during DSC enable
Display Stream Splitter registers need to be programmed to enable
the joiner if two DSC engines are used and also to enable
the left and the right DSC engines. This happens as part of
the DSC enabling routine in the source in atomic commit.
v4:
* Remove redundant comment (Ville)
v3:
* Use cpu_transcoder instead of encoder->type (Ville)
v2:
* Rebase (Manasi)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intelcom>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-11-manasi.d.navare@intel.com
Manasi Navare [Wed, 28 Nov 2018 20:26:21 +0000 (12:26 -0800)]
drm/i915/dp: Populate DSC PPS SDP and send PPS infoframes
DSC PPS secondary data packet infoframes are filled with
DSC picure parameter set metadata according to the DSC standard.
These infoframes are sent to the sink device and used during DSC
decoding.
v3:
* Rename to intel_dp_write_pps_sdp (Ville)
* Use const intel_crtc_state (Ville)
v2:
* Rebase ond drm-tip
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-10-manasi.d.navare@intel.com
Manasi Navare [Wed, 28 Nov 2018 20:26:20 +0000 (12:26 -0800)]
drm/i915/dp: Use the existing write_infoframe() for DSC PPS SDPs
Infoframes are used to send secondary data packets. This patch
adds support for DSC Picture parameter set secondary data packets
in the existing write_infoframe helpers.
v3:
* Unused variables cleanup (Ville)
v2:
* Rebase on drm-tip (Manasi)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-9-manasi.d.navare@intel.com
Manasi Navare [Wed, 28 Nov 2018 20:26:19 +0000 (12:26 -0800)]
drm/i915/dp: Configure i915 Picture parameter Set registers during DSC enabling
After encoder->pre_enable() hook, after link training sequence is
completed, PPS registers for DSC encoder are configured using the
DSC state parameters in intel_crtc_state as part of DSC enabling
routine in the source. DSC enabling routine is called after
encoder->pre_enable() before enbaling the pipe and after
compression is enabled on the sink.
v7:
* Remove unnecessary comments, leftovers (Ville)
* No need for explicit val &= ~ (Ville)
v6:
intel_dsc_enable to be part of pre_enable hook (Ville)
v5:
* make crtc_state const (Ville)
v4:
* Use cpu_transcoder instead of encoder->type for using EDP transcoder
DSC registers(Ville)
* Keep all PSS regs together (Anusha)
v3:
* Configure Pic_width/2 for each VDSC engine when two VDSC engines per pipe
are used (Manasi)
* Add DSC slice_row_per_frame in PPS16 (Manasi)
v2:
* Enable PG2 power well for VDSC on eDP
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
[manasi: fixup the line longer than 100 chars while applying]
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-8-manasi.d.navare@intel.com
Manasi Navare [Wed, 28 Nov 2018 20:26:18 +0000 (12:26 -0800)]
drm/i915/dsc: Add a power domain for VDSC on eDP/MIPI DSI
On Icelake, a separate power well PG2 is created for
VDSC engine used for eDP/MIPI DSI. This patch adds a new
display power domain for Power well 2.
v3:
* Call it POWER_DOMAIN_TRANSCODER_EDP_VDSC (Ville)
* Move it around TRANSCODER power domain defs (Ville)
v2:
* Fix the power well mismatch CI error (Ville)
* Rename as VDSC_PIPE_A (Imre)
* Fix a whitespace (Anusha)
* Fix Comments (Imre)
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-7-manasi.d.navare@intel.com
Gaurav K Singh [Wed, 28 Nov 2018 20:26:17 +0000 (12:26 -0800)]
drm/i915/dp: Enable/Disable DSC in DP Sink
This patch enables decompression support in sink device
before link training and disables the same during the
DDI disabling.
v3 (From manasi):
* Pass bool state to enable/disable (Ville)
v2:(From Manasi)
* Change the enable/disable function to take crtc_state
instead of intel_dp as an argument (Manasi)
* Use the compression_enable flag as part of crtc_state (Manasi)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-6-manasi.d.navare@intel.com
Gaurav K Singh [Wed, 28 Nov 2018 20:26:16 +0000 (12:26 -0800)]
drm/i915/dsc: Compute Rate Control parameters for DSC
This computation of RC params happens in the atomic commit phase
during compute_config() to validate if display stream compression
can be enabled for the requested mode.
v7 (From Manasi):
* Use DRM_DEBUG instead of DRM_ERROR (Ville)
* Use Error numberinstead of -1 (Ville)
v6 (From Manasi):
* Use 9 instead of 0x9 for consistency (Anusha)
v5 (From Manasi):
* Fix dim checkpatch warnings/checks
v4(From Gaurav):
* No change.Rebase on drm-tip
v3 (From Gaurav):
* Rebase on top of Manasi's latest series
* Return -ve value in case of failure scenarios (Manasi)
Fix review comments from Ville:
* Remove unnecessary comments
* Remove unnecessary paranthesis
* Add comments for few RC params calculations
v2 (From Manasi):
* Rebase Gaurav's patch from intel-gfx to gfx-internal
* Use struct drm_dsc_cfg instead of struct intel_dp
as a parameter
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-5-manasi.d.navare@intel.com
Gaurav K Singh [Thu, 29 Nov 2018 19:38:27 +0000 (11:38 -0800)]
drm/i915/dsc: Define & Compute VESA DSC params
This patches does the following:
1. This patch defines all the DSC parameters as per the VESA
DSC specification. These are stored in the encoder and used
to compute the PPS parameters to be sent to the Sink.
2. Compute all the DSC parameters which are derived from DSC
state of intel_crtc_state.
3. Compute all parameters that are VESA DSC specific
This computation happens in the atomic check phase during
compute_config() to validate if display stream compression
can be enabled for the requested mode.
v8 (From Manasi):
* DEBUG_KMS instead of DRM_ERROR for user triggerable
errors (Ville)
v7: (From Manasi)
* Dont use signed int for rc_range_params (Manasi)
* Mask the range_bpg_offset to use only 6 bits
* Add SPDX identifier (Chris Wilson)
v6 (From Manasi):
* Add a check for line_buf_depth return value (Anusha)
* Remove DRM DSC constants to different patch (Manasi)
v5 (From Manasi):
* Add logic to limit the max line buf depth for DSC 1.1 to 13
as per DSC 1.1 spec
* Fix dim checkpatch warnings/checks
v4 (From Gaurav):
* Rebase on latest drm tip
* rename variable name(Manasi)
* Populate linebuf_depth variable(Manasi)
v3 (From Gaurav):
* Rebase my previous patches on top of Manasi's latest patch
series
* Using >>n rather than /2^n (Manasi)
* Change the commit message to explain what the patch is doing(Gaurav)
Fixed review comments from Ville:
* Don't use macro TWOS_COMPLEMENT
* Mention in comment about the source of RC params
* Return directly from case statements
* Using single asssignment for assigning rc_range_params
* Using <<n rather than *2^n and removing the comments
about the fixed point numbers
v2 (From Manasi):
* Update logic for minor version to consider the dpcd value
and what supported by the HW platform
* Use DRM DSC config struct instead of intel_dp struct
* Move the DSC constants to DRM DSC header file
* Use u16, u8 where bigger data types not needed
* * Compute the DSC parameters as part of DSC compute config
since the computation can fail (Manasi)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Co-developed-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181129193827.7914-1-manasi.d.navare@intel.com
Manasi Navare [Wed, 28 Nov 2018 20:26:14 +0000 (12:26 -0800)]
drm/i915/dp: Do not enable PSR2 if DSC is enabled
If a eDP panel supports both PSR2 and VDSC, our HW cannot
support both at a time. Give priority to PSR2 if a requested
resolution can be supported without compression else enable
VDSC and keep PSR2 disabled.
v4:
Fix the unrealted stuff removed during rebase (Ville)
v3:
* Rebase
v2:
* Add warning for DSC and PSR2 enabled together (DK)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-3-manasi.d.navare@intel.com
Manasi Navare [Wed, 28 Nov 2018 21:36:21 +0000 (13:36 -0800)]
drm/i915/dp: Compute DSC pipe config in atomic check
DSC params like the enable, compressed bpp, slice count and
dsc_split are added to the intel_crtc_state. These parameters
are set based on the requested mode and available link parameters
during the pipe configuration in atomic check phase.
These values are then later used to populate the remaining DSC
and RC parameters before enbaling DSC in atomic commit.
v15:
* Rebase over drm-tip
v14:
Remove leftovers, use dsc_bpc, refine dsc_compute_config (Ville)
v13:
* Compute DSC bpc only when DSC is req to be enabled (Ville)
v12:
* Override bpp with dsc dpcd color depth (Manasi)
v11:
* Const crtc_state, reject DSC on DP without FEC (Ville)
* Dont set dsc_split to false (Ville)
v10:
* Add a helper for dp_dsc support (Ville)
* Set pipe_config to max bpp, link params for DSC for now (Ville)
* Compute bpp - use dp dsc support helper (Ville)
v9:
* Rebase on top of drm-tip that now uses fast_narrow config
for edp (Manasi)
v8:
* Check for DSC bpc not 0 (manasi)
v7:
* Fix indentation in compute_m_n (Manasi)
v6 (From Gaurav):
* Remove function call of intel_dp_compute_dsc_params() and
invoke intel_dp_compute_dsc_params() in the patch where
it is defined to fix compilation warning (Gaurav)
v5:
Add drm_dsc_cfg in intel_crtc_state (Manasi)
v4:
* Rebase on refactoring of intel_dp_compute_config on tip (Manasi)
* Add a comment why we need to check PSR while enabling DSC (Gaurav)
v3:
* Check PPR > max_cdclock to use 2 VDSC instances (Ville)
v2:
* Add if-else for eDP/DP (Gaurav)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128213621.21391-1-manasi.d.navare@intel.com
Manasi Navare [Wed, 28 Nov 2018 20:26:12 +0000 (12:26 -0800)]
drm/i915/dp: Add DSC params and DSC config to intel_crtc_state
Basic DSC parameters and DSC configuration data needs to be computed
for each of the requested mode during atomic check. This is
required since for certain modes, valid DSC parameters and config
data might not be computed in which case compression cannot be
enabled for that mode.
For that reason we need to add these params and config structure
to the intel_crtc_state so that if valid this state information
can directly be used while enabling DSC in atomic commit.
v2:
* Rebase on drm-tip (Manasi)
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-1-manasi.d.navare@intel.com
Ville Syrjälä [Tue, 25 Sep 2018 19:37:08 +0000 (22:37 +0300)]
drm/i915: Decouple SKL stride units from intel_fb_stride_alignment()
In the future framebuffer stride alignment requirements won't exactly
match the units in which skl+ plane stride is specified. So extract
the code for the skl+ stuff into a separate helper.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180925193714.25280-3-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Ville Syrjälä [Tue, 23 Oct 2018 16:02:01 +0000 (19:02 +0300)]
drm/i915: Make sure fb gtt offsets stay within 32bits
Let's try to make sure the fb offset computations never hit
an integer overflow by making sure the entire fb stays
below 32bits. framebuffer_check() in the core already does
the same check, but as it doesn't know about tiling some things
can slip through. Repeat the check in the driver with tiling
taken into account.
v2: Use add_overflows() after massaging it to work for me (Chris)
v3: Call it add_overflow_t() to match min_t() & co. (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181023160201.9840-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Ville Syrjälä [Wed, 14 Nov 2018 21:07:29 +0000 (23:07 +0200)]
drm/i915: Pass the plane to icl_program_input_csc_coeff()
On icl+ the plane state that gets passed to update_slave() is not
the plane state of the plane we're programming. With NV12 the
plane state would be coming from the master (UV) plane whereas
the plane we're programming is the slave (Y) plane. For that reason
we need to explicitly pass around the slave plane (or we'd have to
otherwise deduce it by checking whether we were called via
.update_plane() or .update_slave()).
In the case of icl_program_input_csc_coeff() it's actually OK to
assume that we are always the master plane because the input CSC
only exists on HDR planes which can never be a slave plane. But
for consistency let's pass in the plane explicitly anyway.
While at it drop the "_coeff" from the function name since it's
kinda redundant, and this makes the name a bit shorter :)
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-14-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Ville Syrjälä [Wed, 14 Nov 2018 21:07:28 +0000 (23:07 +0200)]
drm/i915: Rename the confusing 'plane_id' to 'color_plane'
A variable whose name is 'plane_id' is expected to be of the
enum plane_id type. In this case we have a raw int, which turns
out to refer to the plane of the framebuffer. Rename the variable
to 'color_plane' in line with the trend started earlier.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-13-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Ville Syrjälä [Wed, 14 Nov 2018 21:07:27 +0000 (23:07 +0200)]
drm/i915: Commit skl+ planes in an order that avoids ddb overlaps
skl+ can go belly up if there are overlapping ddb allocations between
planes. If we could absolutely guarantee that we can perform the atomic
update within a single frame we shouldn't have to worry about this. But
we can't rely on that so let's steal the ddb overlap check trick from
skl_update_crtcs() and apply it to the plane updates. Since each step
of the sequence is free from ddb overlaps we don't have to worry about
a vblank sneaking up on us in the middle of the sequence. The partial
state that gets latched by the hardware will be safe. And unlike
skl_update_crtcs() we don't have to intoduce any extra vblank waits
on account of only having to worry about a single pipe.
v2: Fix typo in commit msg (Matt)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-12-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Ville Syrjälä [Tue, 27 Nov 2018 16:59:00 +0000 (18:59 +0200)]
drm/i915: Move ddb/wm programming into plane update/disable hooks on skl+
On SKL+ the plane WM/BUF_CFG registers are a proper part of each
plane's register set. That means accessing them will cancel any
pending plane update, and we would need a PLANE_SURF register write
to arm the wm/ddb change as well.
To avoid all the problems with that let's just move the wm/ddb
programming into the plane update/disable hooks. Now all plane
registers get written in one (hopefully atomic) operation.
To make that feasible we'll move the plane ddb tracking into
the crtc state. Watermarks were already tracked there.
v2: Rebase due to input CSC
v3: Split out a bunch of junk (Matt)
v4: Add skl_wm_add_affected_planes() to deal with
cursor special case and non-zero wm register reset value
v5: Drop the unrelated for_each_intel_plane_mask() fix (Matt)
Remove the redundant ddb memset() (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #v3
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181127165900.31298-1-ville.syrjala@linux.intel.com
Ville Syrjälä [Wed, 14 Nov 2018 21:07:25 +0000 (23:07 +0200)]
drm/i915: Don't pass dev_priv around so much
Simplify the calling convention of the skl+ watermark functions
by not passing around dev_priv needlessly. The callees have
what they need to dig it out anyway.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-10-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Ville Syrjälä [Tue, 27 Nov 2018 16:57:26 +0000 (18:57 +0200)]
drm/i915: Clean up skl+ vs. icl+ watermark computation
Make a cleaner split between the skl+ and icl+ ways of computing
watermarks. This way skl_build_pipe_wm() doesn't have to know any
of the gritty details of icl+ master/slave planes.
We can also simplify a bunch of the lower level code by pulling
the plane visibility checks a bit higher up.
v2: WARN_ON(!visible) for the icl+ master plane case (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181127165726.31122-1-ville.syrjala@linux.intel.com
Ville Syrjälä [Wed, 14 Nov 2018 21:07:23 +0000 (23:07 +0200)]
drm/i915: Pass the entire skl_plane_wm to skl_compute_transition_wm()
We have to pass both level 0 watermark struct and the transition
watermark struct to skl_compute_transition_wm(). Make life less
confusing by just passing the entire plane watermark struct that
contains both aforementioned structures.
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-8-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Ville Syrjälä [Wed, 14 Nov 2018 21:07:22 +0000 (23:07 +0200)]
drm/i915: Remove some useless zeroing on skl+ wm calculations
We memset(0) the entire watermark struct the start, so there's no
need to clear things later on.
v2: Rebase due to some stale w/a removal
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-7-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Ville Syrjälä [Wed, 14 Nov 2018 21:07:21 +0000 (23:07 +0200)]
drm/i915: Fix latency==0 handling for level 0 watermark on skl+
If the level 0 latency is 0 we can't do anything. Return an error
rather than success.
While this can't happen due to WaWmMemoryReadLatency, it can
happen if the user clears out the level 0 latency via debugfs.
v2: Clarify how how we can end here with zero level 0 latency (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-6-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Ville Syrjälä [Wed, 14 Nov 2018 21:07:20 +0000 (23:07 +0200)]
drm/i915: Pass the new crtc_state to ->disable_plane()
We're going to need access to the new crtc state in ->disable_plane()
for SKL+ wm/ddb programming and pre-skl pipe gamma/csc control. Pass
the crtc state down.
We'll also try to make intel_crtc_disable_planes() do the right
thing as much as it's possible. The fact that we don't have a
separate crtc state for the disabled state when we're going to
re-enable the crtc later means we might end up poking at a few
extra planes in there. But that's harmless. I suppose one might
argue that we wouldn't have to care about proper ddb/wm/csc/gamma
if the pipe is going to permanently disable anyway, but the state
checker probably cares so we should try our best to make sure
everything is programmed correctly even in that case.
v2: Fix the commit message a bit (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-5-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Ville Syrjälä [Tue, 27 Nov 2018 16:37:42 +0000 (18:37 +0200)]
drm/i915: Introduce crtc_state->update_planes bitmask
Keep track which planes need updating during the commit. For now
we set the bit for any plane that was or will be visible (including
icl+ nv12 slave planes). In the future I'll have need to update
invisible planes as well, for skl plane ddbs and for pre-skl pipe
gamma/csc control (which lives in the primary plane control register).
v2: Pimp the commit message to mention icl+ nv12 slave planes (Matt)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181127163742.30215-1-ville.syrjala@linux.intel.com
Ville Syrjälä [Wed, 14 Nov 2018 21:07:18 +0000 (23:07 +0200)]
drm/i915: Move single buffered plane register writes to the end
The plane color correction registers are single buffered. So
ideally we would write them at the start of vblank just after the
double buffered plane registers have been latched. Since we have
no convenient way to do that for now let's at least move the
single buffered register writes to happen after the double
buffered registers have been written.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-3-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Ville Syrjälä [Wed, 14 Nov 2018 21:07:17 +0000 (23:07 +0200)]
drm/i915: Reorganize plane register writes to make them more atomic
Some observations about the plane registers:
- the control register will self-arm if the plane is not already
enabled, thus we want to write it as close to (or ideally after)
the surface register
- tileoff/linoff/offset/aux_offset are self-arming as well so we want
them close to the surface register as well
- color keying registers we maybe self arming before SKL. Not 100%
sure but we can try to keep them near to the surface register
as well
- chv pipe b csc register are double buffered but self arming so
moving them down a bit
- the rest should be mostly armed by the surface register so we can
safely write them first, and to just for some consistency let's try
to follow keep them in order based on the register offset
None of this will have any effect of course unless the vblank evasion
fails (which it still does sometimes). Another potential future benefit
might be pulling the non-self armings registers outside the vblank
evasion since they won't latch until the arming register has been
written. This would make the critical section a bit lighter and thus
less likely to exceed the deadline.
v2: Rebase due to input CSC
v3: Swap LINOFF/TILEOFF and KEYMSK/KEYMAX to actually follow
the last rule above (Matt)
Add a bit more rationale to the commit message (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114210729.16185-2-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Chris Wilson [Wed, 28 Nov 2018 13:53:25 +0000 (13:53 +0000)]
drm/i915: Mark up early pre-production Kabylakes
Mark A0 as the one and only pre-production variant of Kabylake and
remove its couple of workarounds, consigning them to the annals of
history.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128135325.10641-1-chris@chris-wilson.co.uk
Manasi Navare [Tue, 27 Nov 2018 21:41:08 +0000 (13:41 -0800)]
drm/dsc: Define the DSC 1.1 and 1.2 Line Buffer depth constants
DSC specification defines linebuf_depth which contains the
line buffer bit depth used to generate the bitstream.
These values are defined as per Table 4.1 in DSC 1.2 spec
v2 (From Manasi):
* Rename as MAX_LINEBUF_DEPTH for DSC 1.1 and DSC 1.2
Cc: dri-devel@lists.freedesktop.org
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Acked-by: Sean Paul <seanpaul@chromium.org> (For merging through
drm-intel)
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181127214125.17658-6-manasi.d.navare@intel.com
Manasi Navare [Tue, 27 Nov 2018 21:41:07 +0000 (13:41 -0800)]
drm/dsc: Add helpers for DSC picture parameter set infoframes
According to Display Stream compression spec 1.2, the picture
parameter set metadata is sent from source to sink device
using the DP Secondary data packet. An infoframe is formed
for the PPS SDP header and PPS SDP payload bytes.
This patch adds helpers to fill the PPS SDP header
and PPS SDP payload according to the DSC 1.2 specification.
v7:
* Use BUILD_BUG_ON() to protect changing struct size (Ville)
* Remove typecaseting (Ville)
* Include byteorder.h in drm_dsc.c (Ville)
* Correct kernel doc spacing (Anusha)
v6:
* Use proper sequence points for breaking down the
assignments (Chris Wilson)
* Use SPDX identifier
v5:
Do not use bitfields for DRM structs (Jani N)
v4:
* Use DSC constants for params that dont change across
configurations
v3:
* Add reference to added kernel-docs in
Documentation/gpu/drm-kms-helpers.rst (Daniel Vetter)
v2:
* Add EXPORT_SYMBOL for the drm functions (Manasi)
Cc: dri-devel@lists.freedesktop.org
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Acked-by: Sean Paul <seanpaul@chromium.org> (For merging through
drm-intel)
Link: https://patchwork.freedesktop.org/patch/msgid/20181127214125.17658-5-manasi.d.navare@intel.com
Srivatsa, Anusha [Tue, 27 Nov 2018 21:41:06 +0000 (13:41 -0800)]
drm/dsc: Define Rate Control values that do not change over configurations
DSC has some Rate Control values that remain constant
across all configurations. These are as per the DSC
standard.
v3:
* Define them in drm_dsc.h as they are
DSC constants (Manasi)
v2:
* Add DP_DSC_ prefix (Jani Nikula)
Cc: dri-devel@lists.freedesktop.org
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Srivatsa, Anusha <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Acked-by: Sean Paul <seanpaul@chromium.org> (For merging through
drm-intel)
Link: https://patchwork.freedesktop.org/patch/msgid/20181127214125.17658-4-manasi.d.navare@intel.com
Manasi Navare [Tue, 27 Nov 2018 21:41:05 +0000 (13:41 -0800)]
drm/dsc: Define VESA Display Stream Compression Capabilities
This defines all the DSC parameters as per the VESA DSC spec
that will be required for DSC encoder/decoder
v6: (From Manasi)
* Add a bit mask for RANGE_BPG_OFFSET for 6 bits(Manasi)
v5 (From Manasi)
* Add the RC constants as per the spec
v4 (From Manasi)
* Add the DSC_MUX_WORD_SIZE constants (Manasi)
v3 (From Manasi)
* Remove the duplicate define (Suggested By:Harry Wentland)
v2: Define this struct in DRM (From Manasi)
* Changed the data types to u8/u16 instead of unsigned longs (Manasi)
* Remove driver specific fields (Manasi)
* Move this struct definition to DRM (Manasi)
* Define DSC 1.2 parameters (Manasi)
* Use DSC_NUM_BUF_RANGES (Manasi)
* Call it drm_dsc_config (Manasi)
Cc: dri-devel@lists.freedesktop.org
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Co-developed-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Sean Paul <seanpaul@chromium.org> (For merging through
drm-intel)
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181127214125.17658-3-manasi.d.navare@intel.com
Manasi Navare [Tue, 27 Nov 2018 21:41:04 +0000 (13:41 -0800)]
drm/dsc: Define Display Stream Compression PPS infoframe
This patch defines a new header file for all the DSC 1.2 structures
and creates a structure for PPS infoframe which will be used to send
picture parameter set secondary data packet for display stream compression.
All the PPS infoframe syntax elements are taken from DSC 1.2 specification
from VESA.
v4:
* Remove redundant blankline in doc (Ville)
* use drm_dsc namespace for all structs (Ville)
* Use packed struct (Ville)
v3:
* Add the SPDX shorthand (Chris Wilson)
v2:
* Do not use bitfields in the struct (Jani Nikula)
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Acked-by: Sean Paul <seanpaul@chromium.org> (For merging through
drm-intel)
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181127214125.17658-2-manasi.d.navare@intel.com
Manasi Navare [Tue, 27 Nov 2018 21:41:03 +0000 (13:41 -0800)]
drm/dsc: Modify DRM helper to return complete DSC color depth capabilities
DSC DPCD color depth register advertises its color depth capabilities
by setting each of the bits that corresponding to a specific color
depth. This patch defines those specific color depths and adds
a helper to return an array of color depth capabilities.
v2:
* Simplify the logic (Ville)
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Acked-by: Sean Paul <seanpaul@chromium.org> (For merging through
drm-intel)
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181127214125.17658-1-manasi.d.navare@intel.com
Chris Wilson [Mon, 26 Nov 2018 09:56:10 +0000 (09:56 +0000)]
drm/i915: Skip engine serialisation for no-op seqno reset
If the engine's seqno is already at our target seqno (most likely it
hasn't been used since the last reset), we can skip serialising the
engine and leave it as is.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181126095610.20962-1-chris@chris-wilson.co.uk
Chris Wilson [Mon, 26 Nov 2018 12:28:21 +0000 (12:28 +0000)]
drm/i915/ringbuffer: 2-step restart
We may be simply restarting too fast for the culmudgeonly gen3/gen4 as
we still see missing interrupts following a reset. So let's try
restarting a little slower, first wake up the ring empty and then tell
it about the work it has to perform.
References: https://bugs.freedesktop.org/show_bug.cgi?id=108735
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181126122821.4537-1-chris@chris-wilson.co.uk
Chris Wilson [Fri, 23 Nov 2018 13:23:25 +0000 (13:23 +0000)]
drm/i915: Cache the error string
Currently, we convert the error state into a string every time we read
from sysfs (and sysfs reads in page size (4KiB) chunks). We do try to
window the string and only capture the portion that is being read, but
that means that we must always convert up to the window to find the
start. For a very large error state bordering on EXEC_OBJECT_CAPTURE
abuse, this is noticeable as it degrades to O(N^2)!
As we do not have a convenient hook for sysfs open(), and we would like
to keep the lazy conversion into a string, do the conversion of the
whole string on the first read and keep the string until the error state
is freed.
v2: Don't double advance simple_read_from_buffer
v3: Due to extreme pain of lack of vrealloc, use a scatterlist
v4: Keep the forward iterator loosely cached
v5: Stylistic improvements to reduce patch size
Reported-by: Jason Ekstrand <jason@jlekstrand.net>
Testcase: igt/gem_exec_capture/many*
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181123132325.26541-1-chris@chris-wilson.co.uk
José Roberto de Souza [Wed, 21 Nov 2018 22:54:41 +0000 (14:54 -0800)]
drm/i915/hsw: Drop the stereo 3D enabled check in psr_compute_config()
We should not access hardware while computing config also we don't
support stereo 3D so this test was never true.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-6-jose.souza@intel.com
José Roberto de Souza [Wed, 21 Nov 2018 22:54:40 +0000 (14:54 -0800)]
drm/i915: Keep PSR disabled after a driver reload after a PSR error
If a PSR error happened and the driver is reloaded, the EDP_PSR_IIR
will still keep the error set even after the reset done in the
irq_preinstall and irq_uninstall hooks.
And enabling in this situation cause the screen to freeze in the
first time that PSR HW tries to activate so lets keep PSR disabled
to avoid any rendering problems.
v5: rebased: using edp_psr_shift()
v4: Moved handling from intel_psr_compute_config() to
intel_psr_init() to avoid hardware access during compute(Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
squash
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-5-jose.souza@intel.com
José Roberto de Souza [Wed, 21 Nov 2018 22:54:39 +0000 (14:54 -0800)]
drm/i915: Disable PSR when a PSR aux error happen
While PSR is active hardware will do aux transactions by it self to
wakeup sink to receive a new frame when necessary. If that
transaction is not acked by sink, hardware will trigger this
interruption.
So let's disable PSR as it is a hint that there is problem with this
sink.
The removed FIXME was asking to manually train the link but we don't
need to do that as by spec sink should do a short pulse when it is
out of sync with source, we just need to make sure it is awaken and
the SDP header with PSR inactive set it will trigger the short pulse
with a error set in the link status.
v3: added workarround to fix scheduled work starvation cause by
to frequent PSR error interruption
v4: only setting irq_aux_error as we don't care in clear it and
not using dev_priv->irq_lock as consequence.
v5: rebased: using edp_psr_shift()
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-4-jose.souza@intel.com
José Roberto de Souza [Wed, 21 Nov 2018 22:54:38 +0000 (14:54 -0800)]
drm/i915: Do not enable PSR in the next modeset after a error
When we detect a error and disable PSR, it is kept disabled until the
next modeset but as the sink already show signs that it do not
properly work with PSR lets disabled it for good to avoid any
additional flickering.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-3-jose.souza@intel.com
José Roberto de Souza [Wed, 21 Nov 2018 22:54:37 +0000 (14:54 -0800)]
drm/i915: Check PSR errors instead of retrain while PSR is enabled
When a PSR error happens sink sets the PSR error register and also
set the link status to a error status.
So in the short pulse handling it was returning earlier and doing a
full detection and attempting to retrain but it fails as PSR HW is
in change of the main-link.
Just call intel_psr_short_pulse() before
intel_dp_needs_link_retrain() is not the right fix as
intel_dp_needs_link_retrain() would return true and trigger a full
detection while PSR HW is still in change of main-link.
Check for PSR active is also not safe as it could be inactive due a
frontbuffer invalidate and still doing the PSR exit sequence.
v3: added comment in intel_dp_needs_link_retrain()
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-2-jose.souza@intel.com
José Roberto de Souza [Wed, 21 Nov 2018 22:54:36 +0000 (14:54 -0800)]
drm/i915: Avoid a full port detection in the first eDP short pulse
Some eDP panels do not set a valid sink count value and even for the
ones that sets is should always be one for eDP, that is why it is not
cached in intel_edp_init_dpcd().
But intel_dp_short_pulse() compares the old count with the read one
if there is a mistmatch a full port detection will be executed, what
was happening in the first short pulse interruption of eDP panels
that sets sink count.
Instead of just skip the compasison for eDP panels, lets not read
the sink count at all for eDP.
v2: the previous version of this patch it was caching the sink count
in intel_edp_init_dpcd() but I was pointed out by Ville a patch that
handled a case of a eDP panel that do not set sink count and as sink
count is not used to eDP certification was choosed to just not read
it at all.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121225441.18785-1-jose.souza@intel.com
Lyude Paul [Wed, 21 Nov 2018 00:37:17 +0000 (19:37 -0500)]
drm/i915: Synchronize hpd work in i915_hpd_storm_ctl_show()
While trying to add a chamelium test for short HPD IRQs, I ran into
issues where a hotplug storm would be triggered, but the point at which
it would be reported by the kernel would be after igt actually finished
checking i915_hpd_storm_ctl's status. So, fix this by simply
synchronizing our IRQ work, dig_port_work, and hotplug_work before
printing out the HPD storm status in i915_hpd_storm_ctl_show().
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121003718.17704-1-lyude@redhat.com
Ville Syrjälä [Mon, 29 Oct 2018 18:34:53 +0000 (20:34 +0200)]
drm/i915: Eliminate the horrendous format check code
Replace the messy framebuffer format/modifier validation code
with a single call to drm_any_plane_has_format(). The code was
extremely annoying to maintain as you had to have a lot of platform
checks for different formats. The new code requires zero maintenance.
v2: Nuke the modifier checks as well since the core does that too now
v3: Call drm_any_plane_has_format() from the driver code
v4: Rebase
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181029183453.28541-2-ville.syrjala@linux.intel.com
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Jani Nikula [Thu, 22 Nov 2018 14:49:47 +0000 (16:49 +0200)]
drm/i915: Update DRIVER_DATE to
20181122
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Jani Nikula [Thu, 22 Nov 2018 14:03:03 +0000 (16:03 +0200)]
drm/i915: Update DRIVER_DATE to
20181122
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Hans Holmberg [Wed, 21 Nov 2018 09:54:23 +0000 (10:54 +0100)]
drm/i915: avoid rebuilding i915_gpu_error.o on version string updates
There is no need to rebuild i915_gpu_error.o when the version string
changes as the version is available in init_utsname()->release.
Signed-off-by: Hans Holmberg <hans.holmberg@cnexlabs.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121095423.20760-1-hans.ml.holmberg@owltronix.com
Chris Wilson [Wed, 21 Nov 2018 15:16:53 +0000 (15:16 +0000)]
drm/i915: Show waiter's status on engine dump
When showing the list of waiters, include the task's status so that we
can tell if they have been woken up and are waiting for the CPU, or if
they are still waiting to be woken.
v2: task_state_to_char()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121151653.24595-1-chris@chris-wilson.co.uk
Ville Syrjälä [Tue, 20 Nov 2018 13:54:50 +0000 (15:54 +0200)]
drm/i915: Add rotation readout for plane initial config
If we need to force a full plane update before userspace/fbdev
have given us a proper plane state we should try to maintain the
current plane state as much as possible (apart from the parts
of the state we're trying to fix up with the plane update).
To that end add basic readout for the plane rotation and
maintain it during the initial fb takeover.
Cc: Hans de Goede <hdegoede@redhat.com>
Fixes: 516a49cc1946 ("drm/i915: Fix assert_plane() warning on bootup with external display")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181120135450.3634-2-ville.syrjala@linux.intel.com
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Ville Syrjälä [Tue, 20 Nov 2018 13:54:49 +0000 (15:54 +0200)]
drm/i915: Force a LUT update in intel_initial_commit()
If we force a plane update to fix up our half populated plane state
we'll also force on the pipe gamma for the plane (since we always
enable pipe gamma currently). If the BIOS hasn't programmed a sensible
LUT into the hardware this will cause the image to become corrupted.
Typical symptoms are a purple/yellow/etc. flash when the driver loads.
To avoid this let's program something sensible into the LUT when
we do the plane update. In the future I plan to add proper plane
gamma enable readout so this is just a temporary measure.
Cc: Hans de Goede <hdegoede@redhat.com>
Fixes: 516a49cc1946 ("drm/i915: Fix assert_plane() warning on bootup with external display")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181120135450.3634-1-ville.syrjala@linux.intel.com
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Imre Deak [Mon, 19 Nov 2018 18:00:21 +0000 (20:00 +0200)]
drm/i915: Make CHICKEN_TRANS reg not depend on enum value
Depending on the transcoder enum values to translate from transcoder to
the corresponding CHICKEN_TRANS register can easily break if we add a
new transcoder. Add an explicit mapping instead, by using helpers to
look up the register instance either by transcoder or port (since
unconveniently the registers have both port and transcoder specific
bits).
While at it also check for the correctness of GEN, port, transcoder. I
wasn't sure if psr2_enabled can only be set for GEN9+, but that seems to
be the case indeed (see setting of sink_psr2_support in
intel_psr_init_dpcd()).
v2 (Ville):
- Make gen9_chicken_trans_reg() internal to intel_psr.c.
- s/trans/cpu_transcoder/
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181119180021.370-1-imre.deak@intel.com
Imre Deak [Tue, 20 Nov 2018 09:23:25 +0000 (11:23 +0200)]
drm/i915: Add code comment on assumption of pipe==transcoder
Add a comment to the pipe and transcoder enum definitions about our
assumption in the code about enum values for pipes and transcoders
with a 1:1 transcoder -> pipe mapping.
v2:
- Clarify more what are the assumptions about the enum values. (Ville)
v3: (Lucas)
- s/->/ -> / so it looks less like pointer dereferencing.
- Use pipe enums as initializers in the transcoder enum definition.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v2)
Link: https://patchwork.freedesktop.org/patch/msgid/20181120092325.21249-3-imre.deak@intel.com
Imre Deak [Tue, 20 Nov 2018 09:23:24 +0000 (11:23 +0200)]
drm/i915: Make EDP PSR flags not depend on enum values
Depending on the transcoder enum values to translate from transcoder
to EDP PSR flags can easily break if we add a new transcoder. So remove
the dependency by using an explicit mapping.
While at it also add a WARN for unexpected trancoders.
v2:
- Simplify things by defining flag shift values instead of indices.
- s/trans/cpu_transcoder/ (Ville)
v3:
- Define flags to look like separate bits instead of the values of
the same bitfield. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181120092325.21249-2-imre.deak@intel.com
Imre Deak [Tue, 20 Nov 2018 09:23:23 +0000 (11:23 +0200)]
drm/i915: Make pipe/transcoder offsets not depend on enum values
Depending on the transcoder enum values to translate from transcoder
to pipe/transcoder register addresses can easily break if we add a new
transcoder. So remove the dependency by using named initializers.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181120092325.21249-1-imre.deak@intel.com
Alexandre Belloni [Tue, 20 Nov 2018 15:14:15 +0000 (16:14 +0100)]
drm/i915: fix spelling mistake "reserverd" -> "reserved"
Fix a spelling mistake in a comment.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181120151415.32419-1-alexandre.belloni@bootlin.com
Lucas De Marchi [Sat, 17 Nov 2018 00:42:34 +0000 (16:42 -0800)]
drm/i915: Downgrade unknown CSR firmware warnings
Like it was done in commit
9e180d9991dc ("drm/i915: Downgrade unknown
firmware warnings") for huc and guc: downgrade CSR firmware warnings. If
we have released no firmware yet for a platform, stop scaring the
consumer and merely note its expected absence.
By simply removing the warning and early return we hit the condition
with the appropriate message.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181117004234.23437-2-lucas.demarchi@intel.com
Lucas De Marchi [Sat, 17 Nov 2018 00:42:33 +0000 (16:42 -0800)]
drm/i915: allow to load DMC firmware on next gen
Before commit
d8a5b7d79fb7 ("drm/i915/csr: keep max firmware size together
with firmare name and version") it was possible to load the firmware for
testing purposes via parameter. Let's use the size of the last known
platform to recover that behavior.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181117004234.23437-1-lucas.demarchi@intel.com
José Roberto de Souza [Mon, 19 Nov 2018 23:01:01 +0000 (15:01 -0800)]
drm/i915/ilk: Fix warning when reading emon_status with no output
When there is no output no one will hold a runtime_pm reference
causing a warning when trying to read emom_status in debugfs.
[22.756480] ------------[ cut here ]------------
[22.756489] RPM wakelock ref not held during HW access
[22.756578] WARNING: CPU: 0 PID: 1058 at drivers/gpu/drm/i915/intel_drv.h:2104 gen5_read32+0x16b/0x1a0 [i915]
[22.756580] Modules linked in: snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic i915 coretemp crct10dif_pclmul crc32_pclmul ghash_clmulni_intel snd_hda_intel snd_hda_codec snd_hwdep snd_hda_core e1000e snd_pcm mei_me prime_numbers mei lpc_ich
[22.756595] CPU: 0 PID: 1058 Comm: debugfs_test Not tainted 4.20.0-rc1-CI-Trybot_3219+ #1
[22.756597] Hardware name: Hewlett-Packard HP Compaq 8100 Elite SFF PC/304Ah, BIOS 786H1 v01.13 07/14/2011
[22.756634] RIP: 0010:gen5_read32+0x16b/0x1a0 [i915]
[22.756637] Code: a4 ea e0 0f 0b e9 d2 fe ff ff 80 3d a5 71 19 00 00 0f 85 d3 fe ff ff 48 c7 c7 48 d0 2d a0 c6 05 91 71 19 00 01 e8 35 a4 ea e0 <0f> 0b e9 b9 fe ff ff e8 69 c6 f2 e0 85 c0 75 92 48 c7 c2 78 d0 2d
[22.756639] RSP: 0018:
ffffc90000f1fd38 EFLAGS:
00010282
[22.756642] RAX:
0000000000000000 RBX:
ffff8801f7ab0000 RCX:
0000000000000006
[22.756643] RDX:
0000000000000006 RSI:
ffffffff8212886a RDI:
ffffffff820d6d57
[22.756645] RBP:
0000000000011020 R08:
0000000043e3d1a8 R09:
0000000000000000
[22.756647] R10:
ffffc90000f1fd80 R11:
0000000000000000 R12:
0000000000000001
[22.756649] R13:
ffff8801f7ab0068 R14:
0000000000000001 R15:
ffff88020d53d188
[22.756651] FS:
00007f2878849980(0000) GS:
ffff880213a00000(0000) knlGS:
0000000000000000
[22.756653] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[22.756655] CR2:
00005638deedf028 CR3:
0000000203292001 CR4:
00000000000206f0
[22.756657] Call Trace:
[22.756689] i915_mch_val+0x1b/0x60 [i915]
[22.756721] i915_emon_status+0x45/0xd0 [i915]
[22.756730] seq_read+0xdb/0x3c0
[22.756736] ? lockdep_hardirqs_off+0x94/0xd0
[22.756740] ? __slab_free+0x24e/0x510
[22.756746] full_proxy_read+0x52/0x90
[22.756752] __vfs_read+0x31/0x170
[22.756759] ? do_sys_open+0x13b/0x240
[22.756763] ? rcu_read_lock_sched_held+0x6f/0x80
[22.756766] vfs_read+0x9e/0x140
[22.756770] ksys_read+0x50/0xc0
[22.756775] do_syscall_64+0x55/0x190
[22.756781] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[22.756783] RIP: 0033:0x7f28781dc34e
[22.756786] Code: 00 00 00 00 48 8b 15 71 8c 20 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff c3 0f 1f 40 00 8b 05 ba d0 20 00 85 c0 75 16 31 c0 0f 05 <48> 3d 00 f0 ff ff 77 5a f3 c3 0f 1f 84 00 00 00 00 00 41 54 55 49
[22.756787] RSP: 002b:
00007ffd33fa0d08 EFLAGS:
00000246 ORIG_RAX:
0000000000000000
[22.756790] RAX:
ffffffffffffffda RBX:
0000000000000000 RCX:
00007f28781dc34e
[22.756792] RDX:
0000000000000200 RSI:
00007ffd33fa0d50 RDI:
0000000000000008
[22.756794] RBP:
00007ffd33fa0f60 R08:
0000000000000000 R09:
0000000000000020
[22.756796] R10:
0000000000000000 R11:
0000000000000246 R12:
00005638de45c2c0
[22.756797] R13:
00007ffd33fa14b0 R14:
0000000000000000 R15:
0000000000000000
[22.756806] irq event stamp: 47950
[22.756811] hardirqs last enabled at (47949): [<
ffffffff810fba74>] vprintk_emit+0x124/0x320
[22.756813] hardirqs last disabled at (47950): [<
ffffffff810019b0>] trace_hardirqs_off_thunk+0x1a/0x1c
[22.756816] softirqs last enabled at (47518): [<
ffffffff81c0033a>] __do_softirq+0x33a/0x4b9
[22.756820] softirqs last disabled at (47479): [<
ffffffff8108df29>] irq_exit+0xa9/0xc0
[22.756858] WARNING: CPU: 0 PID: 1058 at drivers/gpu/drm/i915/intel_drv.h:2104 gen5_read32+0x16b/0x1a0 [i915]
[22.756860] ---[ end trace
bf56fa7d6a3cbf7a ]
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181119230101.32460-1-jose.souza@intel.com
Chris Wilson [Tue, 20 Nov 2018 12:06:01 +0000 (12:06 +0000)]
drm/i915/selftests: Hold task reference to reset worker
As the worker may exit by itself, we need to hold a task reference to it
in the parent.
References: https://bugs.freedesktop.org/show_bug.cgi?id=108735
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181120120601.24083-1-chris@chris-wilson.co.uk
Jani Nikula [Tue, 20 Nov 2018 11:14:08 +0000 (13:14 +0200)]
Merge drm/drm-next into drm-intel-next-queued
Pull in v4.20-rc3 via drm-next.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Jani Nikula [Fri, 16 Nov 2018 12:07:29 +0000 (14:07 +0200)]
drm/i915/fixed: cosmetic cleanup
Clean up fixed point temp variable initialization, use the more
conventional tmp name for temp variables, add empty lines before
return. No functional changes.
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181116120729.7580-5-jani.nikula@intel.com
Jani Nikula [Fri, 16 Nov 2018 12:07:28 +0000 (14:07 +0200)]
drm/i915/fixed: simplify is_fixed16_zero()
Simply return the condition. No functional changes.
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181116120729.7580-4-jani.nikula@intel.com
Jani Nikula [Fri, 16 Nov 2018 12:07:27 +0000 (14:07 +0200)]
drm/i915/fixed: simplify FP_16_16_MAX definition
No need to use a compound statement enclosed in parenthesis where a C99
compound literal will do. No functional changes.
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181116120729.7580-3-jani.nikula@intel.com
Jani Nikula [Fri, 16 Nov 2018 12:07:26 +0000 (14:07 +0200)]
drm/i915/fixed: prefer kernel types over stdint types
While at it, conform to kernel spacing (i.e. no space) after cast. No
functional changes.
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181116120729.7580-2-jani.nikula@intel.com
Jani Nikula [Fri, 16 Nov 2018 12:07:25 +0000 (14:07 +0200)]
drm/i915: extract fixed point math to i915_fixed.h
Reduce bloat in one of the bigger header files. Fix some indentation
while at it. No functional changes.
v2: Add include guards (Joonas)
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181116120729.7580-1-jani.nikula@intel.com
Chris Wilson [Mon, 19 Nov 2018 15:41:53 +0000 (15:41 +0000)]
drm/i915: Write GPU relocs harder with gen3
Under moderate amounts of GPU stress, we can observe on Bearlake and
Pineview (later gen3 models) that we execute the following batch buffer
before the write into the batch is coherent. Adding extra (tested with
upto 32x) MI_FLUSH to either the invalidation, flush or both phases does
not solve the incoherency issue with the relocations, but emitting the
MI_STORE_DWORD_IMM twice does. So be it.
Fixes: 7dd4f6729f92 ("drm/i915: Async GPU relocation processing")
Testcase: igt/gem_tiled_fence_blits # blb/pnv
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181119154153.15327-1-chris@chris-wilson.co.uk
Chris Wilson [Fri, 2 Nov 2018 16:12:12 +0000 (16:12 +0000)]
drm/i915: Prevent machine hang from Broxton's vtd w/a and error capture
Since capturing the error state requires fiddling around with the GGTT
to read arbitrary buffers and is itself run under stop_machine(), it
deadlocks the machine (effectively a hard hang) when run in conjunction
with Broxton's VTd workaround to serialize GGTT access.
v2: Store the ERR_PTR in first_error so that the error can be reported
to the user via sysfs.
v3: Mention the quirk in dmesg (using info as per usual)
Fixes: 0ef34ad6222a ("drm/i915: Serialize GTT/Aperture accesses on BXT")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: John Harrison <john.C.Harrison@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181102161232.17742-5-chris@chris-wilson.co.uk
Joonas Lahtinen [Fri, 16 Nov 2018 14:44:47 +0000 (16:44 +0200)]
drm/i915: Hide enable_gvt modparam when not compiled in
Hide the enable_gvt modparam in the default scenario where
support has not been compiled in.
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181116144447.7836-1-joonas.lahtinen@linux.intel.com
Joonas Lahtinen [Fri, 16 Nov 2018 13:55:10 +0000 (15:55 +0200)]
Revert "drm/i915/perf: Fix warning in documentation"
Userspace portion is still missing.
This reverts commit
9fa6e2f7609fdbb7d6f86be86371a5719bec0376.
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181116135510.13807-2-joonas.lahtinen@linux.intel.com
Joonas Lahtinen [Fri, 16 Nov 2018 13:55:09 +0000 (15:55 +0200)]
Revert "drm/i915/perf: add a parameter to control the size of OA buffer"
Userspace portion is still missing.
This reverts commit
cd956bfcd0f58d20485ac0a785415f7d9327a95f.
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181116135510.13807-1-joonas.lahtinen@linux.intel.com
Dave Airlie [Mon, 19 Nov 2018 01:07:52 +0000 (11:07 +1000)]
Merge branch 'drm-next-4.21' of git://people.freedesktop.org/~agd5f/linux into drm-next
New features for 4.21:
amdgpu:
- Support for SDMA paging queue on vega
- Put compute EOP buffers into vram for better performance
- Share more code with amdkfd
- Support for scanout with DCC on gfx9
- Initial kerneldoc for DC
- Updated SMU firmware support for gfx8 chips
- Rework CSA handling for eventual support for preemption
- XGMI PSP support
- Clean up RLC handling
- Enable GPU reset by default on VI, SOC15 dGPUs
- Ring and IB test cleanups
amdkfd:
- Share more code with amdgpu
ttm:
- Move global init out of the drivers
scheduler:
- Track if schedulers are ready for work
- Timeout/fault handling changes to facilitate GPU recovery
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114165113.3751-1-alexander.deucher@amd.com
Dave Airlie [Mon, 19 Nov 2018 00:40:00 +0000 (10:40 +1000)]
Merge tag 'drm-misc-next-2018-11-07' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v4.21, part 1:
UAPI Changes:
- Add syncobj timeline support to drm.
Cross-subsystem Changes:
- Remove shared fence staging in dma-buf's fence object, and allow
reserving more than 1 fence and add more paranoia when debugging.
- Constify infoframe functions in video/hdmi.
Core Changes:
- Add vkms todo, and a lot of assorted doc fixes.
- Drop transitional helpers and convert drivers to use drm_atomic_helper_shutdown().
- Move atomic state helper functions to drm_atomic_state_helper.[ch]
- Refactor drm selftests, and add new tests.
- DP MST atomic state cleanups.
- Drop EXPORT_SYMBOL from drm leases.
- Lease cleanups and fixes.
- Create render node for vgem.
Driver Changes:
- Fix build failure in imx without fbdev emulation.
- Add rotation quirk for GPD win2 panel.
- Add support for various CDTech panels, Banana Pi Panel, DLC1010GIG,
Olimex LCD-O-LinuXino, Samsung S6D16D0, Truly NT35597 WQXGA,
Himax HX8357D, simulated RTSM AEMv8.
- Add dw_hdmi support to rockchip driver.
- Fix YUV support in vc4.
- Fix resource id handling in virtio.
- Make rockchip use dw-mipi-dsi bridge driver, and add dual dsi support.
- Advertise that tinydrm only supports DRM_FORMAT_MOD_LINEAR.
- Convert many drivers to use atomic helpers, and drm_fbdev_generic_setup().
- Add Mali linear tiled formats, and enable them in the Mali-DP driver.
- Add support for H6 DE3 mixer 0, DW HDMI, HDMI PHY and TCON TOP.
- Assorted driver cleanups and fixes.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/be7ebd91-edd9-8fa4-4286-1c57e3165113@linux.intel.com
Linus Torvalds [Sun, 18 Nov 2018 21:33:44 +0000 (13:33 -0800)]
Linux 4.20-rc3
Linus Torvalds [Sun, 18 Nov 2018 20:21:09 +0000 (12:21 -0800)]
Merge tag 'libnvdimm-fixes-4.20-rc3' of git://git./linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"A small batch of fixes for v4.20-rc3.
The overflow continuation fix addresses something that has been broken
for several releases. Arguably it could wait even longer, but it's a
one line fix and this finishes the last of the known address range
scrub bug reports. The revert addresses a lockdep regression. The unit
tests are not critical to fix, but no reason to hold this fix back.
Summary:
- Address Range Scrub overflow continuation handling has been broken
since it was initially merged. It was only recently that error
injection and platform-BIOS support enabled this corner case to be
exercised.
- The recent attempt to provide more isolation for the kernel Address
Range Scrub state machine from userapace initiated sessions
triggers a lockdep report. Revert and try again at the next merge
window.
- Fix a kasan reported buffer overflow in libnvdimm unit test
infrastrucutre (nfit_test)"
* tag 'libnvdimm-fixes-4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
Revert "acpi, nfit: Further restrict userspace ARS start requests"
acpi, nfit: Fix ARS overflow continuation
tools/testing/nvdimm: Fix the array size for dimm devices.
Linus Torvalds [Sun, 18 Nov 2018 19:31:26 +0000 (11:31 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"16 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm/memblock.c: fix a typo in __next_mem_pfn_range() comments
mm, page_alloc: check for max order in hot path
scripts/spdxcheck.py: make python3 compliant
tmpfs: make lseek(SEEK_DATA/SEK_HOLE) return ENXIO with a negative offset
lib/ubsan.c: don't mark __ubsan_handle_builtin_unreachable as noreturn
mm/vmstat.c: fix NUMA statistics updates
mm/gup.c: fix follow_page_mask() kerneldoc comment
ocfs2: free up write context when direct IO failed
scripts/faddr2line: fix location of start_kernel in comment
mm: don't reclaim inodes with many attached pages
mm, memory_hotplug: check zone_movable in has_unmovable_pages
mm/swapfile.c: use kvzalloc for swap_info_struct allocation
MAINTAINERS: update OMAP MMC entry
hugetlbfs: fix kernel BUG at fs/hugetlbfs/inode.c:444!
kernel/sched/psi.c: simplify cgroup_move_task()
z3fold: fix possible reclaim races
Linus Torvalds [Sun, 18 Nov 2018 18:58:20 +0000 (10:58 -0800)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull scheduler fix from Ingo Molnar:
"Fix an exec() related scalability/performance regression, which was
caused by incorrectly calculating load and migrating tasks on exec()
when they shouldn't be"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix cpu_util_wake() for 'execl' type workloads
Linus Torvalds [Sun, 18 Nov 2018 18:54:59 +0000 (10:54 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Fix uncore PMU enumeration for CofeeLake CPUs"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/uncore: Support CoffeeLake 8th CBOX
perf/x86/intel/uncore: Add more IMC PCI IDs for KabyLake and CoffeeLake CPUs
Linus Torvalds [Sun, 18 Nov 2018 18:52:26 +0000 (10:52 -0800)]
Merge branch 'efi-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull EFI fixes from Ingo Molnar:
"Misc fixes: two warning splat fixes, a leak fix and persistent memory
allocation fixes for ARM"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: Permit calling efi_mem_reserve_persistent() from atomic context
efi/arm: Defer persistent reservations until after paging_init()
efi/arm/libstub: Pack FDT after populating it
efi/arm: Revert deferred unmap of early memmap mapping
efi: Fix debugobjects warning on 'efi_rts_work'
Linus Torvalds [Sun, 18 Nov 2018 18:45:09 +0000 (10:45 -0800)]
Merge branch 'spectre' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM spectre updates from Russell King:
"These are the currently known final bits that resolve the Spectre
issues. big.Little systems used to be sufficiently identical in that
there were no differences between individual CPUs in the system that
mattered to the kernel. With the advent of the Spectre problem, the
CPUs now have differences in how the workaround is applied.
As a result of previous Spectre patches, these systems ended up
reporting quite a lot of:
"CPUx: Spectre v2: incorrect context switching function, system vulnerable"
messages due to the action of the big.Little switcher causing the CPUs
to be re-initialised regularly. This series resolves that issue by
making the CPU vtable unique to each CPU.
However, since this is used very early, before per-cpu is setup,
per-cpu can't be used. We also have a problem that two of the methods
are not called from preempt-safe paths, but thankfully these remain
identical between all CPUs in the system. To make sure, we validate
that these are identical during boot"
* 'spectre' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: spectre-v2: per-CPU vtables to work around big.Little systems
ARM: add PROC_VTABLE and PROC_TABLE macros
ARM: clean up per-processor check_bugs method call
ARM: split out processor lookup
ARM: make lookup_processor_type() non-__init
Chen Chang [Fri, 16 Nov 2018 23:08:57 +0000 (15:08 -0800)]
mm/memblock.c: fix a typo in __next_mem_pfn_range() comments
Link: http://lkml.kernel.org/r/20181107100247.13359-1-rainccrun@gmail.com
Signed-off-by: Chen Chang <rainccrun@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Fri, 16 Nov 2018 23:08:53 +0000 (15:08 -0800)]
mm, page_alloc: check for max order in hot path
Konstantin has noticed that kvmalloc might trigger the following
warning:
WARNING: CPU: 0 PID: 6676 at mm/vmstat.c:986 __fragmentation_index+0x54/0x60
[...]
Call Trace:
fragmentation_index+0x76/0x90
compaction_suitable+0x4f/0xf0
shrink_node+0x295/0x310
node_reclaim+0x205/0x250
get_page_from_freelist+0x649/0xad0
__alloc_pages_nodemask+0x12a/0x2a0
kmalloc_large_node+0x47/0x90
__kmalloc_node+0x22b/0x2e0
kvmalloc_node+0x3e/0x70
xt_alloc_table_info+0x3a/0x80 [x_tables]
do_ip6t_set_ctl+0xcd/0x1c0 [ip6_tables]
nf_setsockopt+0x44/0x60
SyS_setsockopt+0x6f/0xc0
do_syscall_64+0x67/0x120
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
the problem is that we only check for an out of bound order in the slow
path and the node reclaim might happen from the fast path already. This
is fixable by making sure that kvmalloc doesn't ever use kmalloc for
requests that are larger than KMALLOC_MAX_SIZE but this also shows that
the code is rather fragile. A recent UBSAN report just underlines that
by the following report
UBSAN: Undefined behaviour in mm/page_alloc.c:3117:19
shift exponent 51 is too large for 32-bit type 'int'
CPU: 0 PID: 6520 Comm: syz-executor1 Not tainted 4.19.0-rc2 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xd2/0x148 lib/dump_stack.c:113
ubsan_epilogue+0x12/0x94 lib/ubsan.c:159
__ubsan_handle_shift_out_of_bounds+0x2b6/0x30b lib/ubsan.c:425
__zone_watermark_ok+0x2c7/0x400 mm/page_alloc.c:3117
zone_watermark_fast mm/page_alloc.c:3216 [inline]
get_page_from_freelist+0xc49/0x44c0 mm/page_alloc.c:3300
__alloc_pages_nodemask+0x21e/0x640 mm/page_alloc.c:4370
alloc_pages_current+0xcc/0x210 mm/mempolicy.c:2093
alloc_pages include/linux/gfp.h:509 [inline]
__get_free_pages+0x12/0x60 mm/page_alloc.c:4414
dma_mem_alloc+0x36/0x50 arch/x86/include/asm/floppy.h:156
raw_cmd_copyin drivers/block/floppy.c:3159 [inline]
raw_cmd_ioctl drivers/block/floppy.c:3206 [inline]
fd_locked_ioctl+0xa00/0x2c10 drivers/block/floppy.c:3544
fd_ioctl+0x40/0x60 drivers/block/floppy.c:3571
__blkdev_driver_ioctl block/ioctl.c:303 [inline]
blkdev_ioctl+0xb3c/0x1a30 block/ioctl.c:601
block_ioctl+0x105/0x150 fs/block_dev.c:1883
vfs_ioctl fs/ioctl.c:46 [inline]
do_vfs_ioctl+0x1c0/0x1150 fs/ioctl.c:687
ksys_ioctl+0x9e/0xb0 fs/ioctl.c:702
__do_sys_ioctl fs/ioctl.c:709 [inline]
__se_sys_ioctl fs/ioctl.c:707 [inline]
__x64_sys_ioctl+0x7e/0xc0 fs/ioctl.c:707
do_syscall_64+0xc4/0x510 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Note that this is not a kvmalloc path. It is just that the fast path
really depends on having sanitzed order as well. Therefore move the
order check to the fast path.
Link: http://lkml.kernel.org/r/20181113094305.GM15120@dhcp22.suse.cz
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reported-by: Kyungtae Kim <kt0755@gmail.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Pavel Tatashin <pavel.tatashin@microsoft.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Aaron Lu <aaron.lu@intel.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Byoungyoung Lee <lifeasageek@gmail.com>
Cc: "Dae R. Jeong" <threeearcat@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Uwe Kleine-König [Fri, 16 Nov 2018 23:08:43 +0000 (15:08 -0800)]
scripts/spdxcheck.py: make python3 compliant
Without this change the following happens when using Python3 (3.6.6):
$ echo "GPL-2.0" | python3 scripts/spdxcheck.py -
FAIL: 'str' object has no attribute 'decode'
Traceback (most recent call last):
File "scripts/spdxcheck.py", line 253, in <module>
parser.parse_lines(sys.stdin, args.maxlines, '-')
File "scripts/spdxcheck.py", line 171, in parse_lines
line = line.decode(locale.getpreferredencoding(False), errors='ignore')
AttributeError: 'str' object has no attribute 'decode'
So as the line is already a string, there is no need to decode it and
the line can be dropped.
/usr/bin/python on Arch is Python 3. So this would indeed be worth
going into 4.19.
Link: http://lkml.kernel.org/r/20181023070802.22558-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Joe Perches <joe@perches.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yufen Yu [Fri, 16 Nov 2018 23:08:39 +0000 (15:08 -0800)]
tmpfs: make lseek(SEEK_DATA/SEK_HOLE) return ENXIO with a negative offset
Other filesystems such as ext4, f2fs and ubifs all return ENXIO when
lseek (SEEK_DATA or SEEK_HOLE) requests a negative offset.
man 2 lseek says
: EINVAL whence is not valid. Or: the resulting file offset would be
: negative, or beyond the end of a seekable device.
:
: ENXIO whence is SEEK_DATA or SEEK_HOLE, and the file offset is beyond
: the end of the file.
Make tmpfs return ENXIO under these circumstances as well. After this,
tmpfs also passes xfstests's generic/448.
[akpm@linux-foundation.org: rewrite changelog]
Link: http://lkml.kernel.org/r/1540434176-14349-1-git-send-email-yuyufen@huawei.com
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Hugh Dickins <hughd@google.com>
Cc: William Kucharski <william.kucharski@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnd Bergmann [Fri, 16 Nov 2018 23:08:35 +0000 (15:08 -0800)]
lib/ubsan.c: don't mark __ubsan_handle_builtin_unreachable as noreturn
gcc-8 complains about the prototype for this function:
lib/ubsan.c:432:1: error: ignoring attribute 'noreturn' in declaration of a built-in function '__ubsan_handle_builtin_unreachable' because it conflicts with attribute 'const' [-Werror=attributes]
This is actually a GCC's bug. In GCC internals
__ubsan_handle_builtin_unreachable() declared with both 'noreturn' and
'const' attributes instead of only 'noreturn':
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=84210
Workaround this by removing the noreturn attribute.
[aryabinin: add information about GCC bug in changelog]
Link: http://lkml.kernel.org/r/20181107144516.4587-1-aryabinin@virtuozzo.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Acked-by: Olof Johansson <olof@lixom.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Janne Huttunen [Fri, 16 Nov 2018 23:08:32 +0000 (15:08 -0800)]
mm/vmstat.c: fix NUMA statistics updates
Scan through the whole array to see if an update is needed. While we're
at it, use sizeof() to be safe against any possible type changes in the
future.
The bug here is that we wouldn't sync per-cpu counters into global ones
if there was an update of numa_stats for higher cpus. Highly
theoretical one though because it is much more probable that zone_stats
are updated so we would refresh anyway. So I wouldn't bother to mark
this for stable, yet something nice to fix.
[mhocko@suse.com: changelog enhancement]
Link: http://lkml.kernel.org/r/1541601517-17282-1-git-send-email-janne.huttunen@nokia.com
Fixes: 1d90ca897cb0 ("mm: update NUMA counter threshold size")
Signed-off-by: Janne Huttunen <janne.huttunen@nokia.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Rapoport [Fri, 16 Nov 2018 23:08:29 +0000 (15:08 -0800)]
mm/gup.c: fix follow_page_mask() kerneldoc comment
Commit
df06b37ffe5a ("mm/gup: cache dev_pagemap while pinning pages")
modified the signature of follow_page_mask() but left the parameter
description behind.
Update the description to make the code and comments agree again.
While at it, update formatting of the return value description to match
Documentation/doc-guide/kernel-doc.rst guidelines.
Link: http://lkml.kernel.org/r/1541603316-27832-1-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wengang Wang [Fri, 16 Nov 2018 23:08:25 +0000 (15:08 -0800)]
ocfs2: free up write context when direct IO failed
The write context should also be freed even when direct IO failed.
Otherwise a memory leak is introduced and entries remain in
oi->ip_unwritten_list causing the following BUG later in unlink path:
ERROR: bug expression: !list_empty(&oi->ip_unwritten_list)
ERROR: Clear inode of 215043, inode has unwritten extents
...
Call Trace:
? __set_current_blocked+0x42/0x68
ocfs2_evict_inode+0x91/0x6a0 [ocfs2]
? bit_waitqueue+0x40/0x33
evict+0xdb/0x1af
iput+0x1a2/0x1f7
do_unlinkat+0x194/0x28f
SyS_unlinkat+0x1b/0x2f
do_syscall_64+0x79/0x1ae
entry_SYSCALL_64_after_hwframe+0x151/0x0
This patch also logs, with frequency limit, direct IO failures.
Link: http://lkml.kernel.org/r/20181102170632.25921-1-wen.gang.wang@oracle.com
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Reviewed-by: Junxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: Changwei Ge <ge.changwei@h3c.com>
Reviewed-by: Joseph Qi <jiangqi903@gmail.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Fri, 16 Nov 2018 23:08:22 +0000 (15:08 -0800)]
scripts/faddr2line: fix location of start_kernel in comment
Fix a source file reference location to the correct path name.
Link: http://lkml.kernel.org/r/1d50bd3d-178e-dcd8-779f-9711887440eb@infradead.org
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Roman Gushchin [Fri, 16 Nov 2018 23:08:18 +0000 (15:08 -0800)]
mm: don't reclaim inodes with many attached pages
Spock reported that commit
172b06c32b94 ("mm: slowly shrink slabs with a
relatively small number of objects") leads to a regression on his setup:
periodically the majority of the pagecache is evicted without an obvious
reason, while before the change the amount of free memory was balancing
around the watermark.
The reason behind is that the mentioned above change created some
minimal background pressure on the inode cache. The problem is that if
an inode is considered to be reclaimed, all belonging pagecache page are
stripped, no matter how many of them are there. So, if a huge
multi-gigabyte file is cached in the memory, and the goal is to reclaim
only few slab objects (unused inodes), we still can eventually evict all
gigabytes of the pagecache at once.
The workload described by Spock has few large non-mapped files in the
pagecache, so it's especially noticeable.
To solve the problem let's postpone the reclaim of inodes, which have
more than 1 attached page. Let's wait until the pagecache pages will be
evicted naturally by scanning the corresponding LRU lists, and only then
reclaim the inode structure.
Link: http://lkml.kernel.org/r/20181023164302.20436-1-guro@fb.com
Signed-off-by: Roman Gushchin <guro@fb.com>
Reported-by: Spock <dairinin@gmail.com>
Tested-by: Spock <dairinin@gmail.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: <stable@vger.kernel.org> [4.19.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Fri, 16 Nov 2018 23:08:15 +0000 (15:08 -0800)]
mm, memory_hotplug: check zone_movable in has_unmovable_pages
Page state checks are racy. Under a heavy memory workload (e.g. stress
-m 200 -t 2h) it is quite easy to hit a race window when the page is
allocated but its state is not fully populated yet. A debugging patch to
dump the struct page state shows
has_unmovable_pages: pfn:0x10dfec00, found:0x1, count:0x0
page:
ffffea0437fb0000 count:1 mapcount:1 mapping:
ffff880e05239841 index:0x7f26e5000 compound_mapcount: 1
flags: 0x5fffffc0090034(uptodate|lru|active|head|swapbacked)
Note that the state has been checked for both PageLRU and PageSwapBacked
already. Closing this race completely would require some sort of retry
logic. This can be tricky and error prone (think of potential endless
or long taking loops).
Workaround this problem for movable zones at least. Such a zone should
only contain movable pages. Commit
15c30bc09085 ("mm, memory_hotplug:
make has_unmovable_pages more robust") has told us that this is not
strictly true though. Bootmem pages should be marked reserved though so
we can move the original check after the PageReserved check. Pages from
other zones are still prone to races but we even do not pretend that
memory hotremove works for those so pre-mature failure doesn't hurt that
much.
Link: http://lkml.kernel.org/r/20181106095524.14629-1-mhocko@kernel.org
Fixes: 15c30bc09085 ("mm, memory_hotplug: make has_unmovable_pages more robust")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Baoquan He <bhe@redhat.com>
Tested-by: Baoquan He <bhe@redhat.com>
Acked-by: Baoquan He <bhe@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vasily Averin [Fri, 16 Nov 2018 23:08:11 +0000 (15:08 -0800)]
mm/swapfile.c: use kvzalloc for swap_info_struct allocation
Commit
a2468cc9bfdf ("swap: choose swap device according to numa node")
changed 'avail_lists' field of 'struct swap_info_struct' to an array.
In popular linux distros it increased size of swap_info_struct up to 40
Kbytes and now swap_info_struct allocation requires order-4 page.
Switch to kvzmalloc allows to avoid unexpected allocation failures.
Link: http://lkml.kernel.org/r/fc23172d-3c75-21e2-d551-8b1808cbe593@virtuozzo.com
Fixes: a2468cc9bfdf ("swap: choose swap device according to numa node")
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Acked-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Huang Ying <ying.huang@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Aaro Koskinen [Fri, 16 Nov 2018 23:08:08 +0000 (15:08 -0800)]
MAINTAINERS: update OMAP MMC entry
Jarkko's e-mail address hasn't worked for a long time. We still want to
keep this driver working as it is critical for some of the OMAP boards.
I use and test this driver frequently, so change myself as a maintainer
with "Odd Fixes" status.
Link: http://lkml.kernel.org/r/20181106222750.12939-1-aaro.koskinen@iki.fi
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Kravetz [Fri, 16 Nov 2018 23:08:04 +0000 (15:08 -0800)]
hugetlbfs: fix kernel BUG at fs/hugetlbfs/inode.c:444!
This bug has been experienced several times by the Oracle DB team. The
BUG is in remove_inode_hugepages() as follows:
/*
* If page is mapped, it was faulted in after being
* unmapped in caller. Unmap (again) now after taking
* the fault mutex. The mutex will prevent faults
* until we finish removing the page.
*
* This race can only happen in the hole punch case.
* Getting here in a truncate operation is a bug.
*/
if (unlikely(page_mapped(page))) {
BUG_ON(truncate_op);
In this case, the elevated map count is not the result of a race.
Rather it was incorrectly incremented as the result of a bug in the huge
pmd sharing code. Consider the following:
- Process A maps a hugetlbfs file of sufficient size and alignment
(PUD_SIZE) that a pmd page could be shared.
- Process B maps the same hugetlbfs file with the same size and
alignment such that a pmd page is shared.
- Process B then calls mprotect() to change protections for the mapping
with the shared pmd. As a result, the pmd is 'unshared'.
- Process B then calls mprotect() again to chage protections for the
mapping back to their original value. pmd remains unshared.
- Process B then forks and process C is created. During the fork
process, we do dup_mm -> dup_mmap -> copy_page_range to copy page
tables. Copying page tables for hugetlb mappings is done in the
routine copy_hugetlb_page_range.
In copy_hugetlb_page_range(), the destination pte is obtained by:
dst_pte = huge_pte_alloc(dst, addr, sz);
If pmd sharing is possible, the returned pointer will be to a pte in an
existing page table. In the situation above, process C could share with
either process A or process B. Since process A is first in the list,
the returned pte is a pointer to a pte in process A's page table.
However, the check for pmd sharing in copy_hugetlb_page_range is:
/* If the pagetables are shared don't copy or take references */
if (dst_pte == src_pte)
continue;
Since process C is sharing with process A instead of process B, the
above test fails. The code in copy_hugetlb_page_range which follows
assumes dst_pte points to a huge_pte_none pte. It copies the pte entry
from src_pte to dst_pte and increments this map count of the associated
page. This is how we end up with an elevated map count.
To solve, check the dst_pte entry for huge_pte_none. If !none, this
implies PMD sharing so do not copy.
Link: http://lkml.kernel.org/r/20181105212315.14125-1-mike.kravetz@oracle.com
Fixes: c5c99429fa57 ("fix hugepages leak due to pagetable page sharing")
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Prakash Sangappa <prakash.sangappa@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Olof Johansson [Fri, 16 Nov 2018 23:08:00 +0000 (15:08 -0800)]
kernel/sched/psi.c: simplify cgroup_move_task()
The existing code triggered an invalid warning about 'rq' possibly being
used uninitialized. Instead of doing the silly warning suppression by
initializa it to NULL, refactor the code to bail out early instead.
Warning was:
kernel/sched/psi.c: In function `cgroup_move_task':
kernel/sched/psi.c:639:13: warning: `rq' may be used uninitialized in this function [-Wmaybe-uninitialized]
Link: http://lkml.kernel.org/r/20181103183339.8669-1-olof@lixom.net
Fixes: 2ce7135adc9ad ("psi: cgroup support")
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vitaly Wool [Fri, 16 Nov 2018 23:07:56 +0000 (15:07 -0800)]
z3fold: fix possible reclaim races
Reclaim and free can race on an object which is basically fine but in
order for reclaim to be able to map "freed" object we need to encode
object length in the handle. handle_to_chunks() is then introduced to
extract object length from a handle and use it during mapping.
Moreover, to avoid racing on a z3fold "headless" page release, we should
not try to free that page in z3fold_free() if the reclaim bit is set.
Also, in the unlikely case of trying to reclaim a page being freed, we
should not proceed with that page.
While at it, fix the page accounting in reclaim function.
This patch supersedes "[PATCH] z3fold: fix reclaim lock-ups".
Link: http://lkml.kernel.org/r/20181105162225.74e8837d03583a9b707cf559@gmail.com
Signed-off-by: Vitaly Wool <vitaly.vul@sony.com>
Signed-off-by: Jongseok Kim <ks77sj@gmail.com>
Reported-by-by: Jongseok Kim <ks77sj@gmail.com>
Reviewed-by: Snild Dolkow <snild@sony.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 16 Nov 2018 19:18:36 +0000 (13:18 -0600)]
Merge tag 'fsnotify_for_v4.20-rc3' of git://git./linux/kernel/git/jack/linux-fs
Pull fsnotify fix from Jan Kara:
"One small fsnotify fix for duplicate events"
* tag 'fsnotify_for_v4.20-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
fanotify: fix handling of events on child sub-directory
Linus Torvalds [Fri, 16 Nov 2018 17:38:14 +0000 (11:38 -0600)]
Merge tag 'gfs2-4.20.fixes3' of git://git./linux/kernel/git/gfs2/linux-gfs2
Pull bfs2 fixes from Andreas Gruenbacher:
"Fix two bugs leading to leaked buffer head references:
- gfs2: Put bitmap buffers in put_super
- gfs2: Fix iomap buffer head reference counting bug
And one bug leading to significant slow-downs when deleting large
files:
- gfs2: Fix metadata read-ahead during truncate (2)"
* tag 'gfs2-4.20.fixes3' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
gfs2: Fix iomap buffer head reference counting bug
gfs2: Fix metadata read-ahead during truncate (2)
gfs2: Put bitmap buffers in put_super
Andreas Gruenbacher [Sun, 11 Nov 2018 11:15:21 +0000 (11:15 +0000)]
gfs2: Fix iomap buffer head reference counting bug
GFS2 passes the inode buffer head (dibh) from gfs2_iomap_begin to
gfs2_iomap_end in iomap->private. It sets that private pointer in
gfs2_iomap_get. Users of gfs2_iomap_get other than gfs2_iomap_begin
would have to release iomap->private, but this isn't done correctly,
leading to a leak of buffer head references.
To fix this, move the code for setting iomap->private from
gfs2_iomap_get to gfs2_iomap_begin.
Fixes: 64bc06bb32 ("gfs2: iomap buffered write support")
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 16 Nov 2018 16:37:27 +0000 (10:37 -0600)]
Merge branch 'linus' of git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes the following issues:
- Potential memory overwrite in simd
- Kernel info leaks in crypto_user
- NULL dereference and use-after-free in hisilicon"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: user - Zeroize whole structure given to user space
crypto: user - fix leaking uninitialized memory to userspace
crypto: simd - correctly take reqsize of wrapped skcipher into account
crypto: hisilicon - Fix reference after free of memories on error path
crypto: hisilicon - Fix NULL dereference for same dst and src
projects / openwrt / staging / blogic.git / log