Daniel Golle [Wed, 29 Apr 2020 19:59:04 +0000 (20:59 +0100)]
ath79: add support for Teltonika RUT955 H7V3C0
This board was previously supported in ar71xx as 'RUT9XX'. The
difference between that and the other RUT955 board already supported in
ath79 is that instead of the SPI shift registers driving the LEDs and
digital outputs that model got an I2C GPIO expander instead.
To support LEDs during early boot and interrupt-driven digital inputs,
I2C support as well as support for PCA953x has to be built-in and
cannot be kernel modules, hence select those symbols for ath79/generic.
Specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344)
- built-in 4G/3G module (example: Quectel EC-25EU)
- internal microSD slot (spi-mmc, buggy and disabled for now)
- RS232 on D-Sub9 port (Cypress ACM via USB, /dev/ttyACM0)
- RS422/RS485 (AR934x high speed UART, /dev/ttyATH1)
- analog 0-24V input (MCP3221)
- various digital inputs and outputs incl. a relay
- 11x LED (4 are driven by AR9344, 7 by PCA9539)
- 2x miniSIM slot (can be swapped via GPIO)
- 2x RP-SMA/F (Wi-Fi), 3x SMA/F (2x WWAN, GPS)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- debugging UART available on PCB edge connector
Serial console (/dev/ttyS0) pinout:
- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side
Flash instruction:
Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.06.051" firmware and U-Boot "3.0.1".
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Tue, 28 Apr 2020 17:19:48 +0000 (18:19 +0100)]
ath79: split Teltonika RUT955 to support other RUT9xx models
Split device-tree of Teltonika RUT955 into a generic RUT9xx part and
a part specific to that version of RUT955 already supported.
Also harmonize GPIO and LED names with what is used by the vendor
firmware and assign RS485 DTR signal.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Wed, 29 Apr 2020 18:48:52 +0000 (19:48 +0100)]
ugps: nmea: fix time comparision
Fix bug causing system time to be set over and over again, and causing
massive log pollution.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Adrian Schmutzler [Wed, 29 Apr 2020 16:04:16 +0000 (18:04 +0200)]
kirkwood: disable image for Linksys EA3500 (Audi)
Due to the switch to DSA, the kernel image has become too big (2641k) for the
kernel partition (2624k) on this device:
WARNING: Image file [...]/linux-kirkwood/linksys_audi-uImage is too big
Disable the device until this is fixed, so buildbots can continue their work.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
David Bauer [Sun, 26 Apr 2020 17:42:29 +0000 (19:42 +0200)]
kernel: hwmon: add Analog Devices AD741x support
Signed-off-by: David Bauer <mail@david-bauer.net>
Kevin Darbyshire-Bryant [Mon, 27 Apr 2020 20:28:42 +0000 (21:28 +0100)]
build: prereq: change minimum make version to 3.82
undefine was added in make 3.82 which is now some 10 years ago, some
make scripts are beginning to use 'undefine'
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Adrian Schmutzler [Tue, 28 Apr 2020 18:28:06 +0000 (20:28 +0200)]
ath79: add SUPPORTED_DEVICES based on ar71xx for some devices
This adds some still-missing board names for old TP-Link devices
to ath79 SUPPORTED_DEVICES.
Fixes: FS#3017
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Tue, 28 Apr 2020 14:51:41 +0000 (16:51 +0200)]
Revert "ramips: explicitly disable built-in switch for lan-only devices"
This reverts commit
a1693bf626f8cd00363b0b98642b682522dfcf75.
The rt288x and rt3883 devices in question don't have switches.
Only keep the merged case for rt305x.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Tue, 28 Apr 2020 09:58:32 +0000 (11:58 +0200)]
kirkwood: remove support for kernel 4.19
kirkwood has moved to DSA on 5.4, which will make kernel 4.14 and 4.19
support broken on the affected devices.
Support on kernel 5.4 seems to have been running fine for almost 2 months
on multiple devices, while support for 4.19 has never left testing state.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Pawel Dembicki <paweldembicki@gmail.com>
Adrian Schmutzler [Tue, 28 Apr 2020 09:52:40 +0000 (11:52 +0200)]
kirkwood: remove support for kernel 4.14
kirkwood has moved to DSA on 5.4, which will make kernel 4.14 and 4.19
support broken on the affected devices.
Support on kernel 5.4 seems to have been running fine for almost 2 months
on multiple devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Pawel Dembicki <paweldembicki@gmail.com>
Pawel Dembicki [Mon, 20 Apr 2020 08:06:36 +0000 (10:06 +0200)]
kirkwood: switch from swconfig to dsa
This patch removes support for swconfig and switches to dsa driver.
swconfig and switch drivers are removed. DSA driver is enabled and
configuration is adjusted.
In kirkwood only two devices have switches: Linksys EA3500 and EA4500.
WAN MAC configuration in 02_network is required because otherwise WAN
would have the same MAC address as lan interfaces. In swconfig solution
the WAN address was assigned in u-Boot to eth1. Now, as eth1 is disabled
and wan is part of the switch, we have to set it manually.
Compile tested: EA3500, EA4500
Run tested: EA4500
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
[minor commit title/message adjustments, remove swconfig package
for devices]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Antonio Quartulli [Tue, 28 Apr 2020 10:06:58 +0000 (12:06 +0200)]
wpad-wolfssl: fix crypto_bignum_sub()
Backport patch from hostapd.git master that fixes copy/paste error in
crypto_bignum_sub() in crypto_wolfssl.c.
This missing fix was discovered while testing SAE over a mesh interface.
With this fix applied and wolfssl >3.14.4 mesh+SAE works fine with
wpad-mesh-wolfssl.
Cc: Sean Parkinson <sean@wolfssl.com>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
DENG Qingfang [Tue, 28 Apr 2020 03:38:51 +0000 (11:38 +0800)]
ramips: fix MikroTik 750Gr3 ports MAC addresses
According to a user in OpenWrt forum, on RouterOS the MAC addresses are
ether1(WAN) = MAC
ether2(LAN2) = MAC+1
ether3(LAN3) = MAC+2
etc.
Fix the MAC addresses in OpenWrt.
Ref: https://forum.openwrt.org/t/few-dumb-question-about-mt7530-rb750gr3-dsa/61608
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[remove label_mac in 02_network]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Álvaro Fernández Rojas [Sun, 26 Apr 2020 19:35:53 +0000 (21:35 +0200)]
ath10k-ct-firmware: add htt-mgt variants
For wave-2, there is now a new variant: htt-mgt-community (vs the old
full-htt-mgt-community).
The non-full one (hence forth 'diet') compiles out a lot of firmware features
that ath10k does not use. This saves a lot of resources and lets one
configure more stations/vdevs/etc using fwcfg.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Álvaro Fernández Rojas [Sun, 26 Apr 2020 19:11:34 +0000 (21:11 +0200)]
ath10k-ct-firmware: update firmware images
No release notes this time.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Álvaro Fernández Rojas [Sun, 26 Apr 2020 19:30:16 +0000 (21:30 +0200)]
ath10k-ct-firmware: rename ct-htt packages
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Álvaro Fernández Rojas [Sun, 26 Apr 2020 18:52:52 +0000 (20:52 +0200)]
ath10k-firmware: move CT firmwares to new package
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Álvaro Fernández Rojas [Sun, 26 Apr 2020 10:40:42 +0000 (12:40 +0200)]
ath10k-ct: remove old patches
Only keep 5.4 patches.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Luiz Angelo Daros de Luca [Mon, 27 Apr 2020 21:45:44 +0000 (18:45 -0300)]
elfutils: powerpc build fix
Fixes following build error on mpc85xx/generic:
ppc_initreg.c: In function 'ppc_set_initial_registers_tid':
ppc_initreg.c:79:22: error: field 'r' has incomplete type
struct pt_regs r;
Ref: FS#2924
Fixes: d27623b54254 ("elfutils: update to 0.179")
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
[commit description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Sat, 25 Apr 2020 12:56:20 +0000 (14:56 +0200)]
wireless-regdb: backport three upstream fixes
Another release is overdue for quite some time, so I'm backporting three
fixes from upstream which I plan to backport into 19.07 as well.
Ref: FS#2880
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Andre Heider [Mon, 27 Apr 2020 22:43:46 +0000 (00:43 +0200)]
omap: remove support for kernel 4.14
There's support for 5.4 and 4.19 now, remove the 3rd option.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Andre Heider [Mon, 23 Mar 2020 10:38:33 +0000 (11:38 +0100)]
omap: switch to kernel 5.4
Runtime tested on beagleblack.
Signed-off-by: Andre Heider <a.heider@gmail.com>
[added test comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Andre Heider [Mon, 23 Mar 2020 10:37:41 +0000 (11:37 +0100)]
omap: make kernel_oldconfig
Attempt to keep the same nand/sound/panel functionality using new knobs.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Andre Heider [Mon, 23 Mar 2020 09:05:38 +0000 (10:05 +0100)]
omap: copy kernel 4.19 config for 5.4
Signed-off-by: Andre Heider <a.heider@gmail.com>
Adrian Schmutzler [Mon, 27 Apr 2020 21:26:18 +0000 (23:26 +0200)]
ath79: indicate boot/failsafe/upgrade for NanoBeam/Nanostation AC
Like for Ubiquiti PowerBeam 5AC Gen2, the highest RSSI LED can
be exploited to indicate boot/failsafe/upgrade for the NanoBeam AC
and Nanostation AC as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Roger Pueyo Centelles [Thu, 12 Mar 2020 10:37:10 +0000 (11:37 +0100)]
ath79: add support for Ubiquiti PowerBeam 5AC Gen2
The Ubiquiti PowerBeam 5AC Gen 2 (PBE-5AC-Gen2) is an outdoor 802.11ac
5 GHz bridge with a radio feed and a dish antenna. The device is
hardware-compatible with the LiteBeam AC Gen2, plus the 4 extra LEDs.
Specifications:
- SoC: Qualcomm Atheros AR9342 rev 2
- RAM: 64 MB DDR2
- Flash: 16 MB SPI NOR (mx25l12805d)
- Ethernet: 1x 10/100/1000 Mbps Atheros 8035, 24 Vdc PoE-in
- WiFi 5 GHz: QCA988x HW2.0 Ubiquiti target 0x4100016c chip_id 0x043222ff
- WiFi 2.4 GHz: Atheros AR9340 (SoC-based)
- Buttons: 1x (reset)
- LEDs: 1x power, 1x Ethernet, 4x RSSI via GPIO. All blue.
- UART: not tested
Installation from stock airOS firmware:
- Follow instructions for WA-type Ubiquiti devices on OpenWrt wiki
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[changed device name in commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Mon, 27 Apr 2020 21:04:55 +0000 (23:04 +0200)]
ramips: rt3883: remove swconfig from individual DEVICE_PACKAGES
In rt3883 subtarget, several devices add swconfig to their DEVICE_PACKAGES.
This is redundant as the package is already provided via DEFAULT_PACKAGES.
Remove the redundant inclusions.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Mon, 27 Apr 2020 20:59:40 +0000 (22:59 +0200)]
ramips: remove (kmod-)swconfig DEVICE_PACKAGES for Sitecom WL-351
These definitions are not required since swconfig is selected for
the target anyway and kmod-swconfig is pulled as dependency by
kmod-switch-rtl8366rb.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sungbo Eo [Sat, 25 Apr 2020 09:11:12 +0000 (18:11 +0900)]
ramips: explicitly disable built-in switch for lan-only devices
Commit
8f6334eb947a ("ramips: explicitly disable built-in switch when needed")
did not fix rt288x and rt3883 devices. This patch deals with them.
While at it, consolidate duplicate cases in interface setup.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Adrian Schmutzler [Mon, 27 Apr 2020 10:07:01 +0000 (12:07 +0200)]
ramips: create common definition for I-O DATA NAND devices
Three of the I-O DATA devices with NAND flash share a lot of
variables. Create a common definition for them to reduce duplicate
code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Yong-hyu, Ban [Sun, 26 Apr 2020 09:43:22 +0000 (18:43 +0900)]
mediatek: fix compile error caused by upstreamed mtk_m32 function
This fixes following compile error:
```
CC drivers/net/ethernet/mediatek/mtk_eth_soc.o
drivers/net/ethernet/mediatek/mtk_eth_soc.c:70:5: error: conflicting types for 'mtk_m32'
u32 mtk_m32(struct mtk_eth *eth, u32 mask, u32 set, unsigned reg)
^~~~~~~
In file included from drivers/net/ethernet/mediatek/mtk_eth_soc.c:25:
drivers/net/ethernet/mediatek/mtk_eth_soc.h:964:6: note: previous declaration of 'mtk_m32' was here
void mtk_m32(struct mtk_eth *eth, u32 clear, u32 set, unsigned reg);
^~~~~~~
```
which caused by 5.4.34 mainlining of mtk_m32 function.
Fixes: faf668be354a ("kernel: bump 5.4 to 5.4.34")
Signed-off-by: Yong-hyu, Ban <perillamint@quendi.moe>
Felix Fietkau [Mon, 27 Apr 2020 18:06:40 +0000 (20:06 +0200)]
mt76: update to the latest version
bef8f8a5966d mt76: mt7615: remove a stray if statement
89bd7199487f mt76: remove variable 'val' set but not used
ee8ac234b84e mt76: mt7615: introduce mt7615_mcu_fill_msg
4999db4668f0 mt76: mt7615: introduce mt7615_mcu_wait_response
8ce6e40eba03 mt76: mt7615: cleanup fw queue just for mmio devices
9d1d2ee9add3 mt76: mt7615: introduce mt7615_init_device routine
7fbd2a57cea4 mt76: always init to 0 mcu messages
3b277cf18d95 mt76: mt7615: introduce mt7615_mcu_send_message routine
2a4132a55a4f mt76: mt7615: add mt7615_mcu_ops data structure
9ba71749a122 mt76: mt7615: move mt7615_mcu_set_bmc to mt7615_mcu_ops
2e991f3e8cdd mt76: mt7615: move mt7615_mcu_set_sta in mt7615_mcu_ops
56852057cb90 mt76: mt7615: rely on skb API for mt7615_mcu_set_eeprom
642ecd978887 mt76: mt7615: rework mt7615_mcu_set_bss_info using skb APIs
2b0810af4a52 mt76: mt7615: move more mcu commands in mt7615_mcu_ops data structure
7a6285e63d88 mt76: mt7615: introduce MCU_FW_PREFIX for fw mcu commands
e536b42ebc7d mt76: mt7615: introduce mt7615_register_map
fccbdb628ffd mt76: mt7615: add mt7663e support to mt7615_reg_map
d42244e9255c mt76: mt7615: add mt7663e support to mt7615_{driver,firmware}_own
aebbe088127f mt76: mt7615: add mt7663e support to mt7615_mcu_set_eeprom
28e22d07f892 mt76: mt7615: introduce mt7615_eeprom_parse_hw_band_cap routine
167428592647 mt76: mt7615: introduce mt7615_init_mac_chain routine
23ca7acfc856 mt76: mt7615: introduce uni cmd command types
c4171728cf70 mt76: mt7615: introduce set_bmc and st_sta for uni commands
9e5c76d2310a mt76: mt7615: add more uni mcu commands
779b2cebc147 mt76: mt7615: introduce set_ba uni command
21ee7da00f0a mt76: mt7615: get rid of sta_rec_wtbl data structure
2097f74f664c mt76: mt7615: introduce mt7663e support
8e9cd01228d0 mt7615: sync Kconfig with upstream
3b4f93840950 mt76: add memory barrier to DMA queue kick
8d301ace8ed7 mt76: mt7615: fix mt7663e firmware struct endianness
9bc1850ce711 mt76: mt7615: fix endianness in unified command
a1b9b7d94aa0 mt76: mt7615: add missing declaration in mt7615.h
6e4b2a709fe7 mt76: sync Makefile with upstream
258dfb6afb30 mt76: mt76x02u: Add support for newer versions of the XBox One wifi adapter
9c3d84b62cc0 mt76: mt76x2u: introduce Mercury UD13 support
ea8ea71933ca mt76: mt76x0: pci: add mt7610 PCI ID
9d555f82d329 mt76: mt7615: modify mt7615_ampdu_stat_read for each phy
8bd26d6c3172 mt76: mt7615: enable aggr_stats for both phy
1315afa511e0 mt76: mt7615: cleanup mib related defines and structs
072b50c61e0e mt76: mt7615: add more useful Tx mib counters
b23ff3e9343a mt76: mt7663: fix mt7615_mac_cca_stats_reset routine
294abe47c9b2 mt76: mt7663: enable nf estimation
d2d7bf2243f6 mt76: mt7615: make scs configurable per phy
908a2cfab88f mt76: mt7663: disable RDD commands
eaef0a268b95 mt76: mt7615: add ethool support to mt7663 driver
96e07ef1113d mt76: mt7615: introduce mt7615_mcu_set_channel_domain mcu command
67182f36e3be mt76: mt7663: keep Rx filters as the default
e6a3f3ffe53a mt76: mt7615: introduce hw scan support
12ecd5ba2146 mt76: mt7615: introduce scheduled scan support
f6ab0bee3172 mt76: mt7615: introduce BSS absence event
f208a9430044 mt76: mt7615: introduce rlm tlv in bss_info mcu command
ea4f4d216dbe mt76: mt7615: remove unnecessary register operations
72c9380e70f9 mt76: add headroom and tailroom to mt76_mcu_ops data structure
63e14669e09d mt76: mt7615: introduce mt7663u support to mt7615_write_txwi
29d359ac7626 mt76: mt7615: introduce mt7615_mac_update_rate_desc routine
1f1dd2cb5b49 mt76: mt7615: introduce __mt7663_load_firmware routine
cb6dcfd3cf13 mt76: mt7615: move mt7615_mac_wtbl_addr in mac.h
d28e8e7ef912 mt76: mt76u: rely on mt7622 queue scheme for mt7663u
f78cf8957aba mt76: mt7615: rework wtbl key configuration
2829497aaaf5 mt76: mt7615: introduce mt7615_wtbl_desc data structure
02c9ec4a15e7 mt76: mt7615: add address parameter to mt7615_eeprom_init
e9c640c0a79e mt76: mt7663: correct the name of the rom patch
1e8b2fe5ab03 mt76: mt7615: do not always reset the dfs state setting the channel
ec0ea46dacf9 mt76: mt7615: Delete an error message in mt7622_wmac_probe()
d16a4698f1ac mt76: mt7615: disable merge of OTP ROM data by default
2b58998bb594 mt76: mt7615: add support for applying DC offset calibration from EEPROM
55198aafb756 mt76: mt7615: add support for applying tx DPD calibration from EEPROM
5a1eaa38d380 mt76: mt7603: disable merge of OTP ROM data by default
bf60f43b12fb mt76: mt76x2: disable merge of OTP ROM data by default
9406eb1d110f mt76: mt7615: fix endian issues in applying flash calibration data
66d00b8c9dac mt76: mt7615: fix possible division by 0 in mt7615_mac_update_mib_stats
25d812dddcf8 mt76: mt7663: fix aggr range entry in debugfs
08b8bd2bc915 mt76: mt7615: disable hw/sched scan ops for non-offload firmware
8fb1cd20a776 mt76: mt7615: set hw scan limits only for firmware with offload support
05b23d7478fe mt76: mt7615: rework IRQ handling to prepare for MSI support
b92c0d576769 mt76: mt7622: fix DMA unmap length
03daa60ca69c mt76: mt7663: fix DMA unmap length
5f2f676b1f01 mt76: mt7615: enable MSI by default
5822911f8026 mt76: remove unnecessary annotations
a7035bce8517 mt76: mt7615: fix possible deadlock in mt7615_stop
d4e6e225bc06 mt76: mt7615: move core shared code in mt7615-common module
94827d2033c7 mt76: mt7615: introduce mt7663u support
36591dd35f91 mt76: mt7615: enable scs for mt7663 driver
bd80144cb5be mt76: mt7615: disable aspm by default
9dcb60b78ede mt76: mt7615: provide aid info to the mcu
6e443e89cce2 mt76: remove PS_NULLFUNC_STACK capability
ea133325faa6 mt76: mt7663: introduce 802.11 PS support in sta mode
ff3869b38cf2 mt76: mt7615: make Kconfig entry obvious for MT7663E
01fd34f3a6c5 mt76: mt7615: fix sta ampdu factor for VHT
e5adbb2077e2 mt76: fix A-MPDU density handling
d73e3a23a54e mt76: mt7615: use larger rx buffers if VHT is supported
257319e9b07d mt76: mt7615: never use an 802.11b CF-End rate on 5GHz
29a92c5606d6 mt76: mt7603: never use an 802.11b CF-End rate on 5GHz
c0b19ac97c07 mt76: mt7615: adjust timing in mt7615_mac_set_timing to match fw/hw values
1656882f2723 mt76: mt7615: do not adjust MAC timings if the device is not running
4e7ce907faf3 mt76: mt7615: fix tx status rate index calculation
8304b3866100 mt76: mt7603: fix tx status rate index calculation
722d1f47d8ba mt76: add rx queues info to mt76 debugfs
da329ef776b0 mt76: mt7615: parse mcu return code for unified commands
facf74fd506f mt76: mt7615: fix mt7615_firmware_own for mt7663e
e910787a9888 mt76: mt7615: fix max wtbl size for 7663
c9821f7d6a8c mt76: mt7615: fix mt7615_driver_own routine
e35cc532c3d2 mt76: mt7615: fix aid configuration in mt7615_mcu_wtbl_generic_tlv
b6cb91a71fe1 mt76: mt7615: rework mt7615_mac_sta_poll for usb code
b193dd8100f8 mt76: mt7663u: enable AirTimeFairness
31cffa98920f mt76: mt7615: move mcu bss upload before creating the sta
cde3716aa47e mt76: enable TDLS support
1846da5dd417 mt76: mt7615: set spatial extension index
6aaf0299730f mt76: mt7615: fix endian issues in dcoc/txdpd calibration
5de75b745cf9 mt76: mt7663: fix up BMC entry indicated to unicmd firmware
a5f394c5ca48 mt76: mt7615: add sta pointer to mt7615_mcu_add_bss_info signature
1f2f3dda76b9 mt76: mt7615: fix event report in mt7615_mcu_bss_event
c2a3cced36de mt76: mt76x0: enable MCS 8 and MCS9
1afabe78cfc5 mt76: mt7663: add the possibility to load firmware v2
5f3ccc722627 mt76: mt7663: remove check in mt7663_load_n9
Signed-off-by: Felix Fietkau <nbd@nbd.name>
INAGAKI Hiroshi [Sun, 26 Apr 2020 03:24:33 +0000 (12:24 +0900)]
ramips: use lzma-loader for I-O DATA mt7621 devices
The official sysupgrade images for I-O DATA devices manufactured by
MSTC (MitraStar Technology Corp.) cannot be booted normally and the
kernel panics after switching to kernel 5.4.
This commit fixes the issue by using lzma-loader.
Note:
These devices use Z-LOADER to read the kernel from NAND flash and boot
it. Z-LOADER cannot load and start plain lzma-loader, so additional
lzma-compression is needed.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Co-developed-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Tested-by: Yanase Yuki <dev@zpc.sakura.ne.jp> [wn-ax2033gr]
INAGAKI Hiroshi [Fri, 24 Apr 2020 05:51:53 +0000 (14:51 +0900)]
ramips: use lzma-loader for Japanese mt7621 devices
In several Japanese routers with MT7621 SoC, the official sysupgrade
image cannot be booted properly after switching to kernel 5.4.
This commit fixes the issue by using lzma-loader.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Szabolcs Hubai [Sun, 19 Apr 2020 18:49:11 +0000 (20:49 +0200)]
ramips: mt7621: use lzma-loader for D-Link DIR-860L B1
This device has trouble extracting big kernel from flash,
and supports LZMA compressed kernels only.
Using OpenWrt kernel loader saves us 64 KB compared to the dictionary
size limiting workaround.
Factory image sizes (commit:
5f126c541a74) with "CONFIG_ALL_KMODS=y":
- original ("-d23", default):
4784188 bytes, LZMA ERROR 1
- with "-d19":
4915260, LZMA ERROR 1
- with "-d18":
4915260, diff to original: +128 KB
- with "-d17":
4980796, diff to original: +192 KB
- with this patch:
4849724, diff to original: +64 KB
To save some CPU cycle, use minimal compression ("-a0") for the LZMA
compressed uImage.
The most robust solution would use a different loader,
which reads the compressed kernel directly from the flash.
See the thread at [0] for more details!
[0] http://lists.infradead.org/pipermail/openwrt-devel/2020-April/022926.html
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
Tested-by: Stijn Segers <foss@volatilesystems.org>
[fixed identation]
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Mon, 27 Apr 2020 10:18:12 +0000 (12:18 +0200)]
ath79: enable SGMII workaround for affected boards
These boards suffer from a sudden inability to establish a link on the
SGMII. Enable the workaround to fix the link when it dies.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Mon, 27 Apr 2020 10:18:09 +0000 (12:18 +0200)]
ath79: ag71xx: unify version dependent code
Use IS_ERR_OR_NULL macro to use the same code on kernel 4.19 as well as
5.4.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Mon, 27 Apr 2020 10:18:07 +0000 (12:18 +0200)]
ath79: ag71xx: remove code for legacy kernels
ath79 does not support kernels prior to 4.19 anymore.
Remove legacy code for those kernels from the ag71xx driver.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Mon, 27 Apr 2020 10:18:01 +0000 (12:18 +0200)]
ath79: remove unused TP-Link partition parser
This parser was added with the target, but no device seems to use it
currently, as all partitions are specified in the device-tree.
Signed-off-by: David Bauer <mail@david-bauer.net>
Adrian Schmutzler [Sun, 26 Apr 2020 22:17:07 +0000 (00:17 +0200)]
mvebu: tidy up support for GL.iNet GL-MV1000
This fixes a bunch of cosmetic issues with GL.iNet GL-MV1000:
- apply alphabetic sorting in multiple files
- use armada-3720 prefix for DTS like for other devices
- fix vendor capitalization for model in DTSes
- remove trivial comment in DTS files
- use DEVICE_VENDOR/DEVICE_MODEL
- remove redundant SUPPORTED_DEVICES
- use SOC instead of DEVICE_DTS
- remove empty line at EOF
Fixes: 050c24f05c85 ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
DENG Qingfang [Wed, 15 Apr 2020 04:49:54 +0000 (12:49 +0800)]
bcm53xx: 5.4: enable NAND
NAND driver was dropped in the 5.4 bump, so enable it back
Fixes: 50c6938b95a0 ("bcm53xx: add v5.4 support")
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Li Zhang [Fri, 17 Apr 2020 06:39:32 +0000 (14:39 +0800)]
mvebu: add support for GL.iNet GL-MV1000
This patch adds supports for GL-MV1000.
Specification:
- SOC: Marvell Armada
88F3720 (1GHz)
- Flash: 16MB (W25Q128FWSIG)
- RAM: 1GB DDR4
- Ethernet: 3x GE (1 WAN + 2 LAN)
- EMMC: 8GB EMMC (KLM8G1GETF-B041)
- MicroSD: 1x microSD slot
- USB: 1x USB 2.0 port(TypeA),1x USB 3.0 port(TypeC)
- Button: 1x reset button,1x slide switch
- LED: 3x greed LED
- UART: 1x UART on PCB (JP1: 3.3V, RX, TX, GND)
Update firmware instructions
============================
In the compiled,please gzip -d xxx.img.gz,then update firmware on uboot web.
Signed-off-by: Li Zhang <li.zhang@gl-inet.com>
[Copied dts file to files-5.4]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rosen Penev [Sat, 18 Apr 2020 23:06:15 +0000 (16:06 -0700)]
toolchain/gcc: eliminate uClibc atexit hack
This seems to be over 10 years old. It doesn't seem to be needed anymore.
Tested on malta with uClibc (selected BROKEN).
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Xiaobo Tian [Wed, 1 Apr 2020 04:19:35 +0000 (12:19 +0800)]
kernel: support intel X7xx 10/40GbE adapters
Signed-off-by: Xiaobo Tian <peterwillcn@gmail.com>
[Add i40evf/i40evf.ko and setect CONFIG_IAVF]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Matt Merhar [Sun, 19 Apr 2020 21:12:03 +0000 (17:12 -0400)]
kernel: backport fix for non-regular inodes on f2fs
Upstream commit
dda9f4b9ca ("f2fs: fix to skip verifying block address
for non-regular inode").
On 4.14, attempting to perform operations on a non-regular inode
residing on an f2fs filesystem, such rm-ing a device node, would fail
and lead to a warning / call trace in dmesg. This fix was already
applied to other kernels upstream - including 4.19, from which the patch
was taken.
More info at https://bugzilla.kernel.org/show_bug.cgi?id=202495.
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
weidong jia [Fri, 10 Apr 2020 08:42:37 +0000 (16:42 +0800)]
uboot-envtools: fix domywifi_dw33d Bad CRC error
The current dw33d partition index has changed, this patch solves
this problem.
old partition layout
dev: size erasesize name
mtd0:
00040000 00010000 "u-boot"
mtd1:
00010000 00010000 "u-boot-env"
mtd2:
00fa0000 00010000 "oem-firmware"
mtd3:
00010000 00010000 "art"
mtd4:
00500000 00020000 "kernel"
mtd5:
05b00000 00020000 "ubi"
mtd6:
02000000 00020000 "oem-backup"
new partition layout
dev: size erasesize name
mtd0:
00500000 00020000 "kernel"
mtd1:
05b00000 00020000 "ubi"
mtd2:
02000000 00020000 "oem-backup"
mtd3:
00040000 00010000 "u-boot"
mtd4:
00010000 00010000 "u-boot-env"
mtd5:
00fa0000 00010000 "oem-firmware"
mtd6:
00010000 00010000 "art"
Signed-off-by: weidong jia <jwdsccd@gmail.com>
Lucian Cristian [Sat, 18 Apr 2020 22:39:08 +0000 (01:39 +0300)]
uboot-envtools: update to 2020.04
also revert to directly download the archive from https
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
Lucian Cristian [Sun, 19 Apr 2020 12:52:25 +0000 (15:52 +0300)]
u-boot.mk: switch download to https
ftp can cause problems on some networks switch primary download location
to https and add another mirror
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
Lucian Cristian [Sun, 19 Apr 2020 13:07:10 +0000 (16:07 +0300)]
tools/mkimage: update to 2020.04
also change the download source to https and add a mirror
drop merged patches
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
[Add extra changes to compile on FreeBSD, merge two patches]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Linus Lüssing [Wed, 5 Feb 2020 19:10:43 +0000 (20:10 +0100)]
mac80211: ath10k: increase rx buffer size to 2048
Before, only frames with a maximum size of 1528 bytes could be
transmitted between two 802.11s nodes.
For batman-adv for instance, which adds its own header to each frame,
we typically need an MTU of at least 1532 bytes to be able to transmit
without fragmentation.
This patch now increases the maxmimum frame size from 1528 to 1656
bytes.
Tested with two ath10k devices in 802.11s mode, as well as with
batman-adv on top of 802.11s with forwarding disabled.
Fix originally found and developed by Ben Greear.
Link: https://github.com/greearb/ath10k-ct/issues/89
Link: https://github.com/greearb/ath10k-ct/commit/9e5ab25027e0971fa24ccf93373324c08c4e992d
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Yangbo Lu [Tue, 14 Apr 2020 07:24:50 +0000 (15:24 +0800)]
perf: build with NO_LIBCAP=1
Build with NO_LIBCAP=1. This is to resolve build issue.
Package perf is missing dependencies for the following libraries:
libcap.so.2
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Luiz Angelo Daros de Luca [Thu, 16 Apr 2020 04:23:28 +0000 (01:23 -0300)]
gdb: disable gdbserver for arc
Although gdb is supported, gdbserver is still not.
checking whether gdbserver is supported on this host... no
Build breaks as gdbserver executable is not found during packaging.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Sungbo Eo [Sun, 26 Apr 2020 11:22:33 +0000 (20:22 +0900)]
ramips: remove unnecessary DEVICE_PACKAGES for Belkin F7C027
kmod-usb-dwc2 and kmod-usb-ledtrig-usbport are not target default packages, and
Belkin F7C027 does not have a USB port anyway. Just drop it.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Sun, 26 Apr 2020 10:55:06 +0000 (19:55 +0900)]
ramips: fix SUPPORTED_DEVICES for Mercury MAC1200R v2
Currently SUPPORTED_DEVICES only contains the old device string. Fix it by
removing the first assignment.
Fixes: c2334ad60dc8 ("ramips/mt76x8: Synchronize Makefiles with DTS compatible")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Sungbo Eo [Sun, 22 Mar 2020 17:41:08 +0000 (02:41 +0900)]
oxnas: move service file to correct place
This service file has been misplaced from the very beginning.
Fixes: dcc34574efba ("oxnas: bring in new oxnas target")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
David Bauer [Sun, 26 Apr 2020 11:37:42 +0000 (13:37 +0200)]
kernel: netdev: fix kmod-sfp symbols
Fixes: ec2f7a47d379 ("kernel: add module to support SFP cages")
Signed-off-by: David Bauer <mail@david-bauer.net>
Kevin Darbyshire-Bryant [Sat, 25 Apr 2020 09:27:22 +0000 (10:27 +0100)]
relayd: bump to version 2020-04-25
f4d759b dhcp.c: further improve validation
Further improve input validation for CVE-2020-11752
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Kevin Darbyshire-Bryant [Sat, 25 Apr 2020 09:30:08 +0000 (10:30 +0100)]
umdns: update to version 2020-04-25
cdac046 dns.c: fix input validation fix
Due to a slight foobar typo, failing to de-reference a pointer, previous
fix not quite as complete as it should have been.
Improve CVE-2020-11750 fix
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Petr Štetiar [Sat, 25 Apr 2020 10:47:43 +0000 (12:47 +0200)]
x86: fix unusable squashfs images by adding missing padding
It was reported, that after image generation rework
x86-64-generic-squashfs-rootfs.img image won't boot on XenServer x86_64
anymore:
F2FS-fs (xvda): Magic Mismatch, valid(0xf2f52010) - read(0x84289960)
F2FS-fs (xvda): Can't find valid F2FS filesystem in 1th superblock
F2FS-fs (xvda): Magic Mismatch, valid(0xf2f52010) - read(0x4e8ee223)
F2FS-fs (xvda): Can't find valid F2FS filesystem in 2th superblock
List of all partitions:
ca00 4207 xvda
driver: vbd
No filesystem could mount root, tried:
ext3
ext2
ext4
squashfs
iso9660
f2fs
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(202,0)
So lets fix this by adding back padding which was introduced in commit
a17d9482f5e2 ("x86: image: fix small disk space in squashfs overlay").
Ref: FS#3036
Fixes: 258f070d1a4f ("x86: fix missing squashfs and ext4 rootfs images")
Fixes: cb007a7bf619 ("x86: switch image generation to new code")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
David Bauer [Sun, 26 Apr 2020 10:07:46 +0000 (12:07 +0200)]
kernel: netdev: fix kmod-sfp description capitalization
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Sun, 26 Apr 2020 09:13:53 +0000 (11:13 +0200)]
kernel: netdev: add phylink dependency for sfp
Fixes: ec2f7a47d379 ("kernel: add module to support SFP cages")
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Sun, 26 Apr 2020 09:02:16 +0000 (11:02 +0200)]
kernel: netdev: add kmod-phylink
Signed-off-by: David Bauer <mail@david-bauer.net>
René van Dorst [Tue, 10 Mar 2020 17:34:33 +0000 (01:34 +0800)]
ramips: enable SFP port for Ubiquiti ER-X-SFP
SFP cage of this device is connected via a AT8031 phy to port 5 of the switch.
This phy act as a RGMII-to-SerDes converter.
Also a I2C clock gate needs to be enabled in order to access the SFP module via I2C bus.
SFP cage also has module detect pin which is connected to I2C gpio expander.
With this patch the kernel/PHYLINK now can detect, readout and use the SFP module/port.
NOTE: SFP cage / AT8033 PHY only support 1000base-X encoding!
This means that some SGMII modules can work and only at forced 1GBit/full-duplex!
Signed-off-by: René van Dorst <opensource@vdorst.com>
René van Dorst [Tue, 7 Apr 2020 21:50:31 +0000 (23:50 +0200)]
kernel: add module to support SFP cages
Enables kernel SFP case support.
Signed-off-by: René van Dorst <opensource@vdorst.com>
DENG Qingfang [Tue, 10 Mar 2020 17:30:02 +0000 (01:30 +0800)]
ramips: phy: at803x: support RGMII-to-SerDes and SFP support
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: René van Dorst <opensource@vdorst.com>
DENG Qingfang [Tue, 10 Mar 2020 17:32:12 +0000 (01:32 +0800)]
kernel: backport support for clause 37 1000Base-X auto-negotiation
This patch is needed for clause 37 1000Base-X encoding used in many SFP modules.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: René van Dorst <opensource@vdorst.com>
Petr Štetiar [Sat, 25 Apr 2020 08:58:07 +0000 (10:58 +0200)]
kernel: bump 5.4 to 5.4.35
Refreshed one patch.
Run tested: qemu-x86-64
Build tested: x86/64, imx6, sunxi/a53, rockchip/armv8
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Sat, 25 Apr 2020 09:13:41 +0000 (11:13 +0200)]
imx6: add back perf monitor related config symbol
Commit
0543eb111081 ("imx6: 5.4: add missing kernel perf monitor
symbol") has added missing kernel config symbol FSL_IMX8_DDR_PMU which
is exposed only when building perf, so add it back.
Fixes: 8d9b36270b1f ("imx6: refresh kernel config")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Daniel Golle [Sat, 25 Apr 2020 09:18:22 +0000 (10:18 +0100)]
procd: extend requirejail attribute handling
e2ed964 jail: don't fail unless requirejail is set
17e7ae7 jail: don't load libpreload-seccomp.so if it doesn't exist
Fixes openwrt/packages#11913
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
David Bauer [Wed, 22 Apr 2020 23:21:11 +0000 (01:21 +0200)]
ipq40xx: fix alphabetical order in 02_network
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Sun, 19 Apr 2020 16:28:09 +0000 (18:28 +0200)]
ath79: fix QCA953x DDR and GPIO compatible bindings
The memory as well as GPIO controller had the wrong SoC name used for
their compatible binding.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Sat, 18 Apr 2020 17:16:05 +0000 (19:16 +0200)]
ath79: correct QCA9550 machine compatible binding
Some boards using a QCA9556 or QCA9558 had their machine compatible
binding incorrectly set to qca,qca9557.
Signed-off-by: David Bauer <mail@david-bauer.net>
David Bauer [Fri, 17 Apr 2020 00:05:23 +0000 (02:05 +0200)]
ath79: rename qca9557.dtsi to qca955x.dtsi
There are at least 3 different chips in the Scorpion series of SoCs.
Rename the common DTSI to better reflect it's purpose for the whole
series.
Also rename the compatible bindings from qca,ar9557 and qca,qca9557
to qca,qca9550.
Signed-off-by: David Bauer <mail@david-bauer.net>
Adrian Schmutzler [Tue, 14 Apr 2020 14:10:49 +0000 (16:10 +0200)]
ltq-adsl(-fw): Makefile clean-up and fixes
This fixes a few minor issues (partially cosmetic) in ltq-adsl and
ltq-adsl-fw Makefiles:
- fix PKG_SOURCE_URL and switch to https
- remove non-existant FW_NAME variable
- fix package name for config inclusion
- fix config symbol for debugging
Fixes: 1d0a9d0c0470 ("move ltq-adsl")
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Mon, 13 Apr 2020 16:43:44 +0000 (18:43 +0200)]
ath79: move tplinkpart.c parser to patches
Between 4.19 and 5.4, mtd parsers have been moved to "parsers"
subdirectory. Like for myloader.c in the previous patch,
this patch moves tplinkpart.c to the kernel patches, so the
code and the kernel includes are at the same location and
the path can be adjusted per kernel.
While at it, remove some outdated kernel version switches from
the C code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Mon, 13 Apr 2020 16:43:43 +0000 (18:43 +0200)]
kernel: fix include of myloader.o since kernel 5.4
Between 4.19 and 5.4, mtd parsers have been moved to "parsers"
subdirectory. Based on this, the selection of myloader.o in OpenWrt
was also moved to that subdirectory, while the Kconfig and our local
myloader.c file remained in /drivers/mtd.
This resulted in linking errors like the following (on ath25@5.4):
make[8]: *** No rule to make target 'drivers/mtd/parsers/myloader.o', ...
needed by 'drivers/mtd/parsers/built-in.a'. Stop.
make[7]: *** [scripts/Makefile.build:500: drivers/mtd/parsers] Error 2
make[6]: *** [scripts/Makefile.build:500: drivers/mtd] Error 2
Since myloader.c is not too big, this patch moves it to the kernel patches,
allowing to adjust the path for kernel 5.4 and keeping Makefiles and
file paths better in sync.
Other patches have been refreshed accordingly.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Sun, 12 Apr 2020 09:39:42 +0000 (11:39 +0200)]
kernel: replace "+@" IPV6 dependency by "+"
The combination +@IPV6:kmod-ipsec6 is not valid, the +a:b
syntax implies the @. Fix it.
Fixes: 2e6b6f9fcaae ("kernel: add @IPv6 dependency to ipv6 modules")
Reported-by: Oldřich Jedlička (@oldium)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Wed, 15 Apr 2020 16:34:50 +0000 (18:34 +0200)]
ramips: remove config-4.14 for mt7621/mt76x8
mt7621 and mt76x8 subtargets have been moved to kernel 5.4 and their
DTS(I) files are incompatible to kernel 4.14.
Remove the corresponding kernel config files to signal that more
boldly and to prevent accidentally patching the wrong kernel when
pulling in older config patches.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Thu, 23 Apr 2020 15:03:57 +0000 (17:03 +0200)]
octeon: use kernel version 5.4 for testing
Tested on EdgeRouter Lite (by Daniel Engberg)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Daniel Engberg [Fri, 17 Apr 2020 21:39:35 +0000 (23:39 +0200)]
octeon: update config for kernel 5.4
Update config with make kernel_oldconfig.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
[split patch, redo kernel_oldconfig, add description]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Daniel Engberg [Fri, 17 Apr 2020 19:56:37 +0000 (21:56 +0200)]
octeon: refresh patches for kernel 5.4
Refresh patches to make them apply to kernel 5.4.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
[split patch, refresh on newer kernel, add description]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Daniel Engberg [Fri, 17 Apr 2020 19:53:14 +0000 (21:53 +0200)]
octeon: copy files to kernel 5.4
Copy config and patches to kernel 5.4.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
[split patch, fix patches-5.4 dirname, add description]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Felix Fietkau [Thu, 9 Apr 2020 17:57:47 +0000 (19:57 +0200)]
mediatek: disable the unused pcie port for elecom wrc-2533gent
Fixes MSI support for the primary device
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 9 Apr 2020 12:25:51 +0000 (14:25 +0200)]
fstools: update to the latest version
84965b92f635 blockd: print symlink error code and string message
62c578c22f9d blockd: report "target" path as "mount" for autofs available mounts
d1f1f2b38fa1 block: remove mount target file if it's a link
830441d790d6 blockd: remove symlink linkpath file if it's a dir or link
c80f7002114f libfstools/mtd: attempt to read from OOB data if empty space is found
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Petr Štetiar [Tue, 21 Apr 2020 20:51:20 +0000 (22:51 +0200)]
openssl: bump to 1.1.1g
Fixes NULL dereference in SSL_check_chain() for TLS 1.3, marked with
high severity, assigned CVE-2020-1967.
Ref: https://www.openssl.org/news/secadv/
20200421.txt
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Tue, 21 Apr 2020 09:09:30 +0000 (11:09 +0200)]
kernel: bump 5.4 to 5.4.34
Refreshed patches.
Run tested: qemu-x86-64, apalis, a64-olinuxino
Build tested: x86/64, imx6, sunxi/a53
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Koen Vandeputte [Tue, 21 Apr 2020 12:46:23 +0000 (14:46 +0200)]
imx6: refresh kernel config
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Alexander Couzens [Wed, 13 Nov 2019 17:13:13 +0000 (18:13 +0100)]
base-files: ensure VERBOSE is set
If not set, it shows the following error
sh: out of range
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Alexander Couzens [Mon, 24 Jun 2019 15:41:22 +0000 (17:41 +0200)]
lantiq/fritz 7312: set maximum speed to 100 mbit
The fritz 7312 does not support 1000 gbit. Advertising it makes it
worse. Some NIC will change to 1000 gibt and turn off and on again for
ever.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Hans Dedecker [Mon, 20 Apr 2020 19:22:46 +0000 (21:22 +0200)]
ubus: update to latest git HEAD
171469e lua: avoid truncation of large numeric values
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Daniel Golle [Mon, 20 Apr 2020 18:21:50 +0000 (19:21 +0100)]
x86: really remove packages already enabled in kconfig
This commit really removes packages in geode profiles already enabled
in kernel config.
Fixes: 9c23ecee57 ("x86: move packages selection to profiles")
Reported-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tomasz Maciej Nowak [Mon, 20 Apr 2020 17:46:34 +0000 (19:46 +0200)]
x86: move packages selection to profiles
This can be rather confusing for contributors, since there are three
layers in which they can be added. As for now there are none profiles
other than generic (exception: geos) let's move them to these profiles.
Being here this commit also removes packages in geode profiles already
enabled in kernel config.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tomasz Maciej Nowak [Mon, 20 Apr 2020 17:46:33 +0000 (19:46 +0200)]
x86: select kmod-button-hotplug by default
This package is useful by all subtargets, therefore move it to default
packages selection.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tomasz Maciej Nowak [Mon, 20 Apr 2020 17:46:32 +0000 (19:46 +0200)]
x86: fix kmod-forcedeth package selection
There's no such package as forcedeth, threfore the driver is never
selected. Fix it by properly specifying package name.
Fixes: 35f208d ("x86: add nforce eth to default packages")
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tomasz Maciej Nowak [Mon, 20 Apr 2020 17:46:31 +0000 (19:46 +0200)]
x86: image: drop dead code
These are remnants of old image generation code, which now serve no
purpose.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Petr Štetiar [Mon, 20 Apr 2020 14:42:47 +0000 (16:42 +0200)]
uboot-rockchip: fix ident string
Commit
797506011695 ("uboot-rockchip: add new package") has added
`OpenWRT` ident string, fix it to proper `OpenWrt`.
Fixes: 797506011695 ("uboot-rockchip: add new package")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Tobias Mädel [Sun, 12 Apr 2020 11:57:25 +0000 (13:57 +0200)]
rockchip: add support for Pine64 RockPro64
This adds the new rockchip target and support for RockPro64 RK3399
Flash: 16 MiB SPI NOR
RAM: 2 GiB/4 GiB LPDDR4
SoC: RK3399
USB: 2x USB 2.0, 1x USB 3.0, 1x USB-C
Ethernet: 1x GbE
PCIe: PCIe 2.0, 4 lanes
Storage: eMMC or SD card
Optional SDIO wifi/bt module
The Pine64 RockPro64 is a single-board-computer with a 4x PCIe connector,
6 ARM64 cores (4 little, 2 big), plenty of RAM and storage.
By default the single Gigabit-Ethernet port is configured as the
LAN port.
Installation of the firware is possible by dd'ing the image
to an SD card or the eMMC flash.
Serial: 3v3
1500000 8n1
U-boot is build from the mainline tree and
integrated into the images. Required ATF to build u-boot
is downloaded from a CI build bot.
Signed-off-by: Tobias Mädel <t.maedel@alfeld.de>
Tested-by: Tobias Schramm <t.schramm@manjaro.org>
Tobias Mädel [Sun, 12 Apr 2020 11:53:56 +0000 (13:53 +0200)]
uboot-rockchip: add new package
This package is needed for the rockchip target.
Signed-off-by: Tobias Mädel <t.maedel@alfeld.de>
Tested-by: Tobias Schramm <t.schramm@manjaro.org>
Tobias Mädel [Sun, 12 Apr 2020 11:51:49 +0000 (13:51 +0200)]
arm-trusted-firmware-rockchip: add new package
This is needed to build the uboot-rockchip, needed for the rockchip target
Signed-off-by: Tobias Mädel <t.maedel@alfeld.de>
Tested-by: Tobias Schramm <t.schramm@manjaro.org>
[replaced `mkdir -p` with INSTALL_DIR variable]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Pawel Dembicki [Sat, 11 Apr 2020 13:44:14 +0000 (15:44 +0200)]
uboot-kirkwood: update to 2020.04
Update U-Boot to current 2020.04 release for kirkwood platform.
Catch up with upstream and move some configuration options from
the header files to the corresponding defconfig files.
Compile tested: all devices
Run tested: nsa310, pogoplugv4
Tested-by: Cezary Jackiewicz <cezary@eko.one.pl> [nsa310]
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
projects / openwrt / staging / luka.git / log