Florian Fainelli [Sat, 3 Jun 2017 05:05:23 +0000 (22:05 -0700)]
net: dsa: Fix stale cpu_switch reference after unbind then bind
Commit
9520ed8fb841 ("net: dsa: use cpu_switch instead of ds[0]")
replaced the use of dst->ds[0] with dst->cpu_switch since that is
functionally equivalent, however, we can now run into an use after free
scenario after unbinding then rebinding the switch driver.
The use after free happens because we do correctly initialize
dst->cpu_switch the first time we probe in dsa_cpu_parse(), then we
unbind the driver: dsa_dst_unapply() is called, and we rebind again.
dst->cpu_switch now points to a freed "ds" structure, and so when we
finally dereference it in dsa_cpu_port_ethtool_setup(), we oops.
To fix this, simply set dst->cpu_switch to NULL in dsa_dst_unapply()
which guarantees that we always correctly re-assign dst->cpu_switch in
dsa_cpu_parse().
Fixes: 9520ed8fb841 ("net: dsa: use cpu_switch instead of ds[0]")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 5 Jun 2017 01:41:10 +0000 (21:41 -0400)]
ipv6: Fix leak in ipv6_gso_segment().
If ip6_find_1stfragopt() fails and we return an error we have to free
up 'segs' because nobody else is going to.
Fixes: 2423496af35d ("ipv6: Prevent overrun when parsing v6 header options")
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Garver [Fri, 2 Jun 2017 18:54:10 +0000 (14:54 -0400)]
geneve: fix needed_headroom and max_mtu for collect_metadata
Since commit
9b4437a5b870 ("geneve: Unify LWT and netdev handling.")
when using COLLECT_METADATA geneve devices are created with too small of
a needed_headroom and too large of a max_mtu. This is because
ip_tunnel_info_af() is not valid with the device level info when using
COLLECT_METADATA and we mistakenly fall into the IPv4 case.
For COLLECT_METADATA, always use the worst case of ipv6 since both
sockets are created.
Fixes: 9b4437a5b870 ("geneve: Unify LWT and netdev handling.")
Signed-off-by: Eric Garver <e@erig.me>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Soheil Hassas Yeganeh [Fri, 2 Jun 2017 16:38:22 +0000 (12:38 -0400)]
sock: reset sk_err when the error queue is empty
Prior to
f5f99309fa74 (sock: do not set sk_err in
sock_dequeue_err_skb), sk_err was reset to the error of
the skb on the head of the error queue.
Applications, most notably ping, are relying on this
behavior to reset sk_err for ICMP packets.
Set sk_err to the ICMP error when there is an ICMP packet
at the head of the error queue.
Fixes: f5f99309fa74 (sock: do not set sk_err in sock_dequeue_err_skb)
Reported-by: Cyril Hrubis <chrubis@suse.cz>
Tested-by: Cyril Hrubis <chrubis@suse.cz>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Hocko [Fri, 2 Jun 2017 15:54:08 +0000 (17:54 +0200)]
amd-xgbe: use PAGE_ALLOC_COSTLY_ORDER in xgbe_map_rx_buffer
xgbe_map_rx_buffer is rather confused about what PAGE_ALLOC_COSTLY_ORDER
means. It uses PAGE_ALLOC_COSTLY_ORDER-1 assuming that
PAGE_ALLOC_COSTLY_ORDER is the first costly order which is not the case
actually because orders larger than that are costly. And even that
applies only to sleeping allocations which is not the case here. We
simply do not perform any costly operations like reclaim or compaction
for those. Simplify the code by dropping the order calculation and use
PAGE_ALLOC_COSTLY_ORDER directly.
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Liam McBirnie [Thu, 1 Jun 2017 05:36:01 +0000 (15:36 +1000)]
ip6_tunnel: fix traffic class routing for tunnels
ip6_route_output() requires that the flowlabel contains the traffic
class for policy routing.
Commit
0e9a709560db ("ip6_tunnel, ip6_gre: fix setting of DSCP on
encapsulated packets") removed the code which previously added the
traffic class to the flowlabel.
The traffic class is added here because only route lookup needs the
flowlabel to contain the traffic class.
Fixes: 0e9a709560db ("ip6_tunnel, ip6_gre: fix setting of DSCP on encapsulated packets")
Signed-off-by: Liam McBirnie <liam.mcbirnie@boeing.com>
Acked-by: Peter Dawson <peter.a.dawson@boeing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Timur Tabi [Thu, 1 Jun 2017 21:08:13 +0000 (16:08 -0500)]
net: qcom/emac: do not use hardware mdio automatic polling
Use software polling (PHY_POLL) to check for link state changes instead
of relying on the EMAC's hardware polling feature. Some PHY drivers
are unable to get a functioning link because the HW polling is not
robust enough.
The EMAC is able to poll the PHY on the MDIO bus looking for link state
changes (via the Link Status bit in the Status Register at address 0x1).
When the link state changes, the EMAC triggers an interrupt and tells the
driver what the new state is. The feature eliminates the need for
software to poll the MDIO bus.
Unfortunately, this feature is incompatible with phylib, because it
ignores everything that the PHY core and PHY drivers are trying to do.
In particular:
1. It assumes a compatible register set, so PHYs with different registers
may not work.
2. It doesn't allow for hardware errata that have work-arounds implemented
in the PHY driver.
3. It doesn't support multiple register pages. If the PHY core switches
the register set to another page, the EMAC won't know the page has
changed and will still attempt to read the same PHY register.
4. It only checks the copper side of the link, not the SGMII side. Some
PHY drivers (e.g. at803x) may also check the SGMII side, and
report the link as not ready during autonegotiation if the SGMII link
is still down. Phylib then waits for another interrupt to query
the PHY again, but the EMAC won't send another interrupt because it
thinks the link is up.
Cc: stable@vger.kernel.org # 4.11.x
Tested-by: Manoj Iyer <manoj.iyer@canonical.com>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael S. Tsirkin [Fri, 2 Jun 2017 14:54:33 +0000 (17:54 +0300)]
virtio_net: lower limit on buffer size
commit
d85b758f72b0 ("virtio_net: fix support for small rings")
was supposed to increase the buffer size for small rings but had an
unintentional side effect of decreasing it for large rings. This seems
to break some setups - it's not yet clear why, but increasing buffer
size back to what it was before helps.
Fixes: d85b758f72b0 ("virtio_net: fix support for small rings")
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: "J. Bruce Fields" <bfields@fieldses.org>
Tested-by: Mikulas Patocka <mpatocka@redhat.com>
Tested-by: "J. Bruce Fields" <bfields@fieldses.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chopra, Manish [Fri, 2 Jun 2017 13:52:54 +0000 (06:52 -0700)]
qlcnic: Fix tunnel offload for 82xx adapters
Qlogic's 82xx series adapter doesn't support
tunnel offloads, driver incorrectly assumes that it is
supported and causes firmware hang while running tunnel IO.
This patch fixes this by not advertising tunnel offloads
for 82xx adapters.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark Bloch [Fri, 2 Jun 2017 00:24:08 +0000 (03:24 +0300)]
vxlan: fix use-after-free on deletion
Adding a vxlan interface to a socket isn't symmetrical, while adding
is done in vxlan_open() the deletion is done in vxlan_dellink().
This can cause a use-after-free error when we close the vxlan
interface before deleting it.
We add vxlan_vs_del_dev() to match vxlan_vs_add_dev() and call
it from vxlan_stop() to match the call from vxlan_open().
Fixes: 56ef9c909b40 ("vxlan: Move socket initialization to within rtnl scope")
Acked-by: Jiri Benc <jbenc@redhat.com>
Tested-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Mark Bloch <markb@mellanox.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon [Thu, 1 Jun 2017 20:32:34 +0000 (15:32 -0500)]
ibmvnic: Remove module author mailing address
The original author left the project and so far has not
responded to emails sent to the listed address.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thor Thayer [Wed, 31 May 2017 19:28:47 +0000 (14:28 -0500)]
net: ethernet: stmmac: Fix altr_tse_pcs SGMII Initialization
Fix NETDEV WATCHDOG timeout on startup by adding missing register
writes that properly setup SGMII.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng [Wed, 31 May 2017 18:21:27 +0000 (11:21 -0700)]
tcp: disallow cwnd undo when switching congestion control
When the sender switches its congestion control during loss
recovery, if the recovery is spurious then it may incorrectly
revert cwnd and ssthresh to the older values set by a previous
congestion control. Consider a congestion control (like BBR)
that does not use ssthresh and keeps it infinite: the connection
may incorrectly revert cwnd to an infinite value when switching
from BBR to another congestion control.
This patch fixes it by disallowing such cwnd undo operation
upon switching congestion control. Note that undo_marker
is not reset s.t. the packets that were incorrectly marked
lost would be corrected. We only avoid undoing the cwnd in
tcp_undo_cwnd_reduction().
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar [Wed, 31 May 2017 12:56:28 +0000 (18:26 +0530)]
cxgb4: avoid enabling napi twice to the same queue
Take uld mutex to avoid race between cxgb_up() and
cxgb4_register_uld() to enable napi for the same uld
queue.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Wed, 31 May 2017 12:15:41 +0000 (13:15 +0100)]
ipv6: xfrm: Handle errors reported by xfrm6_find_1stfragopt()
xfrm6_find_1stfragopt() may now return an error code and we must
not treat it as a length.
Fixes: 2423496af35d ("ipv6: Prevent overrun when parsing v6 header options")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 2 Jun 2017 14:37:11 +0000 (10:37 -0400)]
Merge tag 'mac80211-for-davem-2017-06-02' of git://git./linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just two fixes:
* fix the per-CPU drop counters to not be added to the
rx_packets counter, but really the drop counter
* fix TX aggregation start/stop callback races by setting
bits instead of allocating and queueing an skb
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 2 Jun 2017 02:53:04 +0000 (19:53 -0700)]
net: dsa: Move dsa_switch_{suspend,resume} out of legacy.c
dsa_switch_suspend() and dsa_switch_resume() are functions that belong in
net/dsa/dsa.c and are not part of the legacy platform support code.
Fixes: a6a71f19fe5e ("net: dsa: isolate legacy code")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 2 Jun 2017 01:02:39 +0000 (18:02 -0700)]
net: systemport: Fix missing Wake-on-LAN interrupt for SYSTEMPORT Lite
On SYSTEMPORT Lite, since we have the main interrupt source in the first
cell, the second cell is the Wake-on-LAN interrupt, yet the code was not
properly updated to fetch the second cell, and instead looked at the
third and non-existing cell for Wake-on-LAN.
Fixes: 44a4524c54af ("net: systemport: Add support for SYSTEMPORT Lite")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Thu, 1 Jun 2017 19:26:03 +0000 (21:26 +0200)]
mac80211: fix dropped counter in multiqueue RX
In the commit enabling per-CPU station statistics, I inadvertedly
copy-pasted some code to update rx_packets and forgot to change it
to update rx_dropped_misc. Fix that.
This addresses https://bugzilla.kernel.org/show_bug.cgi?id=195953.
Fixes: c9c5962b56c1 ("mac80211: enable collecting station statistics per-CPU")
Reported-by: Petru-Florin Mihancea <petrum@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
David S. Miller [Thu, 1 Jun 2017 19:02:31 +0000 (15:02 -0400)]
Merge branch 'ARM-imx6ul-14x14-evk-Fix-suspend-over-nfs-by-phy'
Leonard Crestez says:
====================
ARM: imx6ul-14x14-evk: Fix suspend over nfs by phy
Right now attempting doing suspend/resume while root is mounted over NFS
hangs on imx6ul-14x14-evk. This is happening because ksz8081 phy fixups are
lost on resume.
Fix this by using equivalent devicetree properties instead of a phy fixup
and handling those properties on resume in the micrel driver.
In theory it might now be possible to remove the phy fixup from mach-imx6ul
entirely but it is possible that this would break other imx6ul boards which
use the same phy. The solution would be to patch their dts but it's not
clear how to identify affected boards.
This code is shared with imx6ull-14x14-evk but 6ull suspend needs an
unrelated patch: https://lkml.org/lkml/2017/5/30/584
This is something of a corner case so there is no CC: stable.
Changes since v1: https://lkml.org/lkml/2017/5/30/672
* Split a kszphy_config_reset function for stuff shared between
config_init and resume. Calling config_init directly could be an option but
on some HW variants it does extra stuff like parsing devicetree options.
That would not be appropriate for resume code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Leonard Crestez [Wed, 31 May 2017 10:29:30 +0000 (13:29 +0300)]
net: phy: micrel: Restore led_mode and clk_sel on resume
These bits seem to be lost after a suspend/resume cycle so just set them
again. Do this by splitting the handling of these bits into a function
that is also called on resume.
This patch fixes ethernet suspend/resume on imx6ul-14x14-evk boards.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leonard Crestez [Wed, 31 May 2017 10:29:29 +0000 (13:29 +0300)]
ARM: dts: imx6ul-14x14-evk: Add ksz8081 phy properties
Right now mach-imx6ul registers a fixup for the ksz8081 phy. The same
register values can be set through the micrel phy driver by using dts
properties.
This seems preferable and allows cleanly fixing suspend/resume.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jia-Ju Bai [Wed, 31 May 2017 07:08:25 +0000 (15:08 +0800)]
mISDN: Fix a sleep-in-atomic bug
The driver may sleep under a read spin lock, and the function call path is:
send_socklist (acquire the lock by read_lock)
skb_copy(GFP_KERNEL) --> may sleep
To fix it, the "GFP_KERNEL" is replaced with "GFP_ATOMIC".
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lance Richardson [Mon, 29 May 2017 17:25:57 +0000 (13:25 -0400)]
vxlan: eliminate cached dst leak
After commit
0c1d70af924b ("net: use dst_cache for vxlan device"),
cached dst entries could be leaked when more than one remote was
present for a given vxlan_fdb entry, causing subsequent netns
operations to block indefinitely and "unregister_netdevice: waiting
for lo to become free." messages to appear in the kernel log.
Fix by properly releasing cached dst and freeing resources in this
case.
Fixes: 0c1d70af924b ("net: use dst_cache for vxlan device")
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Thu, 1 Jun 2017 15:07:55 +0000 (18:07 +0300)]
net: bridge: start hello timer only if device is up
When the transition of NO_STP -> KERNEL_STP was fixed by always calling
mod_timer in br_stp_start, it introduced a new regression which causes
the timer to be armed even when the bridge is down, and since we stop
the timers in its ndo_stop() function, they never get disabled if the
device is destroyed before it's upped.
To reproduce:
$ while :; do ip l add br0 type bridge hello_time 100; brctl stp br0 on;
ip l del br0; done;
CC: Xin Long <lucien.xin@gmail.com>
CC: Ivan Vecera <cera@cera.cz>
CC: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reported-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Fixes: 6d18c732b95c ("bridge: start hello_timer when enabling KERNEL_STP in br_stp_start")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mintz, Yuval [Thu, 1 Jun 2017 12:57:56 +0000 (15:57 +0300)]
bnx2x: Fix Multi-Cos
Apparently multi-cos isn't working for bnx2x quite some time -
driver implements ndo_select_queue() to allow queue-selection
for FCoE, but the regular L2 flow would cause it to modulo the
fallback's result by the number of queues.
The fallback would return a queue matching the needed tc
[via __skb_tx_hash()], but since the modulo is by the number of TSS
queues where number of TCs is not accounted, transmission would always
be done by a queue configured into using TC0.
Fixes: ada7c19e6d27 ("bnx2x: use XPS if possible for bnx2x_select_queue instead of pure hash")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar [Thu, 1 Jun 2017 11:41:30 +0000 (17:11 +0530)]
cxgb4: update latest firmware version supported
Change t4fw_version.h to update latest firmware version
number to 1.16.45.0.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Thu, 1 Jun 2017 08:00:07 +0000 (10:00 +0200)]
netlink: don't send unknown nsid
The NETLINK_F_LISTEN_ALL_NSID otion enables to listen all netns that have a
nsid assigned into the netns where the netlink socket is opened.
The nsid is sent as metadata to userland, but the existence of this nsid is
checked only for netns that are different from the socket netns. Thus, if
no nsid is assigned to the socket netns, NETNSA_NSID_NOT_ASSIGNED is
reported to the userland. This value is confusing and useless.
After this patch, only valid nsid are sent to userland.
Reported-by: Flavio Leitner <fbl@sysclose.org>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jia-Ju Bai [Thu, 1 Jun 2017 08:18:10 +0000 (16:18 +0800)]
qlcnic: Fix a sleep-in-atomic bug in qlcnic_82xx_hw_write_wx_2M and qlcnic_82xx_hw_read_wx_2M
The driver may sleep under a write spin lock, and the function
call path is:
qlcnic_82xx_hw_write_wx_2M (acquire the lock by write_lock_irqsave)
crb_win_lock
qlcnic_pcie_sem_lock
usleep_range
qlcnic_82xx_hw_read_wx_2M (acquire the lock by write_lock_irqsave)
crb_win_lock
qlcnic_pcie_sem_lock
usleep_range
To fix it, the usleep_range is replaced with udelay.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roopa Prabhu [Wed, 31 May 2017 06:50:36 +0000 (23:50 -0700)]
mpls: fix clearing of dead nh_flags on link up
recent fixes to use WRITE_ONCE for nh_flags on link up,
accidently ended up leaving the deadflags on a nh. This patch
fixes the WRITE_ONCE to use freshly evaluated nh_flags.
Fixes: 39eb8cd17588 ("net: mpls: rt_nhn_alive and nh_flags should be accessed using READ_ONCE")
Reported-by: Satish Ashok <sashok@cumulusnetworks.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jia-Ju Bai [Wed, 31 May 2017 01:40:11 +0000 (09:40 +0800)]
isdn: Fix a sleep-in-atomic bug
The driver may sleep under a spin lock, the function call path is:
isdn_ppp_mp_receive (acquire the lock)
isdn_ppp_mp_reassembly
isdn_ppp_push_higher
isdn_ppp_decompress
isdn_ppp_ccp_reset_trans
isdn_ppp_ccp_reset_alloc_state
kzalloc(GFP_KERNEL) --> may sleep
To fixed it, the "GFP_KERNEL" is replaced with "GFP_ATOMIC".
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gustavo A. R. Silva [Tue, 30 May 2017 22:38:43 +0000 (17:38 -0500)]
net: freescale: fix potential null pointer dereference
Add NULL check before dereferencing pointer _id_ in order to avoid
a potential NULL pointer dereference.
Addresses-Coverity-ID:
1397995
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 30 May 2017 20:38:18 +0000 (21:38 +0100)]
net: fix auto-loading of Marvell DSA driver
Auto-loading of the Marvell DSA driver has stopped working with recent
kernels. This seems to be due to the change of binding for DSA devices,
moving them from the platform bus to the MDIO bus.
In order for module auto-loading to work, we need to provide a MODALIAS
string in the uevent file for the device. However, the device core does
not automatically provide this, and needs each bus_type to implement a
uevent method to generate these strings. The MDIO bus does not provide
such a method, so no MODALIAS string is provided:
.# cat /sys/bus/mdio_bus/devices/
f1072004.mdio-mii\:04/uevent
DRIVER=mv88e6085
OF_NAME=switch
OF_FULLNAME=/soc/internal-regs/mdio@72004/switch@4
OF_COMPATIBLE_0=marvell,mv88e6085
OF_COMPATIBLE_N=1
In the case of OF-based devices, the solution is easy -
of_device_uevent_modalias() does the work for us. After this is done,
the uevent file looks like this:
.# cat /sys/bus/mdio_bus/devices/
f1072004.mdio-mii\:04/uevent
DRIVER=mv88e6085
OF_NAME=switch
OF_FULLNAME=/soc/internal-regs/mdio@72004/switch@4
OF_COMPATIBLE_0=marvell,mv88e6085
OF_COMPATIBLE_N=1
MODALIAS=of:NswitchT<NULL>Cmarvell,mv88e6085
which results in auto-loading of the Marvell DSA driver on Clearfog
platforms.
Fixes: c0405563a613 ("ARM: dts: armada-388-clearfog: Utilize new DSA binding")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 30 May 2017 15:21:51 +0000 (16:21 +0100)]
net: phy: fix marvell phy status reading
The Marvell driver incorrectly provides phydev->lp_advertising as the
logical and of the link partner's advert and our advert. This is
incorrect - this field is supposed to store the link parter's unmodified
advertisment.
This allows ethtool to report the correct link partner auto-negotiation
status.
Fixes: be937f1f89ca ("Marvell PHY m88e1111 driver fix")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Douglas Caetano dos Santos [Fri, 26 May 2017 17:28:00 +0000 (14:28 -0300)]
tcp: reinitialize MTU probing when setting MSS in a TCP repair
MTU probing initialization occurred only at connect() and at SYN or
SYN-ACK reception, but the former sets MSS to either the default or the
user set value (through TCP_MAXSEG sockopt) and the latter never happens
with repaired sockets.
The result was that, with MTU probing enabled and unless TCP_MAXSEG
sockopt was used before connect(), probing would be stuck at
tcp_base_mss value until tcp_probe_interval seconds have passed.
Signed-off-by: Douglas Caetano dos Santos <douglascs@taghos.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 30 May 2017 18:18:16 +0000 (14:18 -0400)]
Merge branch 'mlx4-mlx5-MAINTAINERS-update'
Tariq Toukan says:
====================
MAINTAINERS updates
This patchset contains updates to the MAINTAINERS file.
In the first patch, I replace Yishai as the maintainer of
the mlx4_core driver.
In the other two patches we move an RDMA header file from
the list of the mlx4/mlx5 core driver into the respective
IB driver, where it belongs.
Series generated against net commit:
468b0df61a51 Merge git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Tue, 30 May 2017 08:44:06 +0000 (11:44 +0300)]
MAINTAINERS: Move mlx5 rdma header file to IB driver charge
It belongs there, should not be under mlx5 Core driver.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Tue, 30 May 2017 08:44:05 +0000 (11:44 +0300)]
MAINTAINERS: Move mlx4 rdma header file to IB driver charge
It belongs there, should not be under mlx4 Core driver.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Tue, 30 May 2017 08:44:04 +0000 (11:44 +0300)]
MAINTAINERS: Update MELLANOX MLX4 core VPI driver maintainer
Add myself as a maintainer for mlx4 core driver,
replacing Yishai Hadas.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Mon, 29 May 2017 13:00:17 +0000 (15:00 +0200)]
net/mlx5: avoid build warning for uniprocessor
Building the driver with CONFIG_SMP disabled results in a harmless
warning:
ethernet/mellanox/mlx5/core/main.c: In function 'mlx5_irq_set_affinity_hint':
ethernet/mellanox/mlx5/core/main.c:615:6: error: unused variable 'irq' [-Werror=unused-variable]
It's better to express the conditional compilation using IS_ENABLED()
here, as that lets the compiler see what the intented use for the variable
is, and that it can be silently discarded.
Fixes: b665d98edc9a ("net/mlx5: Tolerate irq_set_affinity_hint() failures")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Mon, 29 May 2017 12:56:01 +0000 (14:56 +0200)]
net: dsa: mv88e6xxx: Add missing static to stub functions
'static' was not enough, the helpers must be 'static inline'
net/dsa/mv88e6xxx/global2.h:123:12: error: 'mv88e6xxx_g2_misc_4_bit_port' defined but not used [-Werror=unused-function]
net/dsa/mv88e6xxx/global2.h:117:12: error: 'mv88e6xxx_g2_pvt_write' defined but not used [-Werror=unused-function]
Fixes: c21fbe29f858 ("net: dsa: mv88e6xxx: Add missing static to stub functions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mintz, Yuval [Mon, 29 May 2017 08:24:49 +0000 (11:24 +0300)]
qed: Don't log missing periodic stats by default
Current implementation lacks the logic for providing management
firmware with RDMA-related statistics; [much] worse than that -
it logs such events by default to system logs.
Since the statistics' gathering is done periodically, using sufficiently
new management firmware the system logs would get filled with these
unnecessary prints.
For now, reduce the verbosity of the log so that it would not be
logged by default.
Fixes: 6c75424612a7 ("qed: Add support for NCSI statistics")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin Bucur [Mon, 29 May 2017 06:22:06 +0000 (09:22 +0300)]
Documentation: networking: add DPAA Ethernet document
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guilherme G. Piccoli [Mon, 29 May 2017 02:07:01 +0000 (23:07 -0300)]
cxgb4: avoid crash on PCI error recovery path
During PCI error recovery process, specifically on eeh_err_detected()
we might have a NULL netdev struct, hence a direct dereference will
lead to a kernel oops. This was observed with latest upstream kernel
(v4.12-rc2) on Chelsio adapter T422-CR in PowerPC machines.
This patch checks for NULL pointer and avoids the crash, both in
eeh_err_detected() and eeh_resume(). Also, we avoid to trigger
a fatal error or to try disabling interrupts on FW during PCI
error recovery, because: (a) driver might not be able to accurately
access PCI regions in this case, and (b) trigger a fatal error
_during_ the recovery steps is a mistake that could prevent the
recovery path to complete successfully.
Reported-by: Harsha Thyagaraja <hathyaga@in.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Fri, 26 May 2017 22:27:25 +0000 (00:27 +0200)]
mac80211: fix TX aggregation start/stop callback race
When starting or stopping an aggregation session, one of the steps
is that the driver calls back to mac80211 that the start/stop can
proceed. This is handled by queueing up a fake SKB and processing
it from the normal iface/sdata work. Since this isn't flushed when
disassociating, the following race is possible:
* associate
* start aggregation session
* driver callback
* disassociate
* associate again to the same AP
* callback processing runs, leading to a WARN_ON() that
the TID hadn't requested aggregation
If the second association isn't to the same AP, there would only
be a message printed ("Could not find station: <addr>"), but the
same race could happen.
Fix this by not going the whole detour with a fake SKB etc. but
simply looking up the aggregation session in the driver callback,
marking it with a START_CB/STOP_CB bit and then scheduling the
regular aggregation work that will now process these bits as well.
This also simplifies the code and gets rid of the whole problem
with allocation failures of said skb, which could have left the
session in limbo.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
David S. Miller [Tue, 30 May 2017 03:16:54 +0000 (23:16 -0400)]
Merge git://git./pub/scm/linux/kernel/git/pablo/nf
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree,
they are:
1) Conntrack SCTP CRC32c checksum mangling may operate on non-linear
skbuff, patch from Davide Caratti.
2) nf_tables rb-tree set backend does not handle element re-addition
after deletion in the same transaction, leading to infinite loop.
3) Atomically unclear the IPS_SRC_NAT_DONE_BIT on nat module removal,
from Liping Zhang.
4) Conntrack hashtable resizing while ctnetlink dump is progress leads
to a dead reference to released objects in the lists, also from
Liping.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 28 May 2017 15:25:14 +0000 (17:25 +0200)]
net: dsa: mv88e6xxx: Add missing static to stub functions
Stub functions in header files need to be static, or we can have
multiple definitions errors.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 6335e9f2446b ("net: dsa: mv88e6xxx: mv88e6390X SERDES support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firo Yang [Fri, 26 May 2017 14:37:38 +0000 (22:37 +0800)]
hdlcdrv: Fix divide by zero in hdlcdrv_ioctl
syszkaller fuzzer triggered a divide by zero, when set calibration
through ioctl().
To fix it, test 'bitrate' if it is negative or 0, just return -EINVAL.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Firo Yang <firogm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Thu, 25 May 2017 23:44:43 +0000 (01:44 +0200)]
net: dsa: mv88e6xxx: Add eeprom-length to binding
The binding documentation for the mv88e6xxx switch is missing the
eeprom-length property, which has been implemented since May 2016,
commit
f8cd8753def0 ("dsa: mv88e6xxx: Handle eeprom-length property")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 26 May 2017 21:02:30 +0000 (14:02 -0700)]
Merge tag 'led_fixes_for_4-12-rc3' of git://git./linux/kernel/git/j.anaszewski/linux-leds
Pull LED fix from Jacek Anaszewski:
"A single LED fix for 4.12-rc3.
leds-pca955x driver uses only i2c_smbus API and thus it should pass
I2C_FUNC_SMBUS_BYTE_DATA flag to i2c_check_functionality"
* tag 'led_fixes_for_4-12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: pca955x: Correct I2C Functionality
Linus Torvalds [Fri, 26 May 2017 20:51:01 +0000 (13:51 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Fix state pruning in bpf verifier wrt. alignment, from Daniel
Borkmann.
2) Handle non-linear SKBs properly in SCTP ICMP parsing, from Davide
Caratti.
3) Fix bit field definitions for rss_hash_type of descriptors in mlx5
driver, from Jesper Brouer.
4) Defer slave->link updates until bonding is ready to do a full commit
to the new settings, from Nithin Sujir.
5) Properly reference count ipv4 FIB metrics to avoid use after free
situations, from Eric Dumazet and several others including Cong Wang
and Julian Anastasov.
6) Fix races in llc_ui_bind(), from Lin Zhang.
7) Fix regression of ESP UDP encapsulation for TCP packets, from
Steffen Klassert.
8) Fix mdio-octeon driver Kconfig deps, from Randy Dunlap.
9) Fix regression in setting DSCP on ipv6/GRE encapsulation, from Peter
Dawson.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
ipv4: add reference counting to metrics
net: ethernet: ax88796: don't call free_irq without request_irq first
ip6_tunnel, ip6_gre: fix setting of DSCP on encapsulated packets
sctp: fix ICMP processing if skb is non-linear
net: llc: add lock_sock in llc_ui_bind to avoid a race condition
bonding: Don't update slave->link until ready to commit
test_bpf: Add a couple of tests for BPF_JSGE.
bpf: add various verifier test cases
bpf: fix wrong exposure of map_flags into fdinfo for lpm
bpf: add bpf_clone_redirect to bpf_helper_changes_pkt_data
bpf: properly reset caller saved regs after helper call and ld_abs/ind
bpf: fix incorrect pruning decision when alignment must be tracked
arp: fixed -Wuninitialized compiler warning
tcp: avoid fastopen API to be used on AF_UNSPEC
net: move somaxconn init from sysctl code
net: fix potential null pointer dereference
geneve: fix fill_info when using collect_metadata
virtio-net: enable TSO/checksum offloads for Q-in-Q vlans
be2net: Fix offload features for Q-in-Q packets
vlan: Fix tcp checksum offloads in Q-in-Q vlans
...
Linus Torvalds [Fri, 26 May 2017 19:13:08 +0000 (12:13 -0700)]
Merge tag 'xfs-4.12-fixes-2' of git://git./fs/xfs/xfs-linux
Pull XFS fixes from Darrick Wong:
"A few miscellaneous bug fixes & cleanups:
- Fix indlen block reservation accounting bug when splitting delalloc
extent
- Fix warnings about unused variables that appeared in -rc1.
- Don't spew errors when bmapping a local format directory
- Fix an off-by-one error in a delalloc eof assertion
- Make fsmap only return inode information for CAP_SYS_ADMIN
- Fix a potential mount time deadlock recovering cow extents
- Fix unaligned memory access in _btree_visit_blocks
- Fix various SEEK_HOLE/SEEK_DATA bugs"
* tag 'xfs-4.12-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: Move handling of missing page into one place in xfs_find_get_desired_pgoff()
xfs: Fix off-by-in in loop termination in xfs_find_get_desired_pgoff()
xfs: Fix missed holes in SEEK_HOLE implementation
xfs: fix off-by-one on max nr_pages in xfs_find_get_desired_pgoff()
xfs: fix unaligned access in xfs_btree_visit_blocks
xfs: avoid mount-time deadlock in CoW extent recovery
xfs: only return detailed fsmap info if the caller has CAP_SYS_ADMIN
xfs: bad assertion for delalloc an extent that start at i_size
xfs: fix warnings about unused stack variables
xfs: BMAPX shouldn't barf on inline-format directories
xfs: fix indlen accounting error on partial delalloc conversion
Eric Dumazet [Thu, 25 May 2017 21:27:35 +0000 (14:27 -0700)]
ipv4: add reference counting to metrics
Andrey Konovalov reported crashes in ipv4_mtu()
I could reproduce the issue with KASAN kernels, between
10.246.7.151 and 10.246.7.152 :
1) 20 concurrent netperf -t TCP_RR -H 10.246.7.152 -l 1000 &
2) At the same time run following loop :
while :
do
ip ro add 10.246.7.152 dev eth0 src 10.246.7.151 mtu 1500
ip ro del 10.246.7.152 dev eth0 src 10.246.7.151 mtu 1500
done
Cong Wang attempted to add back rt->fi in commit
82486aa6f1b9 ("ipv4: restore rt->fi for reference counting")
but this proved to add some issues that were complex to solve.
Instead, I suggested to add a refcount to the metrics themselves,
being a standalone object (in particular, no reference to other objects)
I tried to make this patch as small as possible to ease its backport,
instead of being super clean. Note that we believe that only ipv4 dst
need to take care of the metric refcount. But if this is wrong,
this patch adds the basic infrastructure to extend this to other
families.
Many thanks to Julian Anastasov for reviewing this patch, and Cong Wang
for his efforts on this problem.
Fixes: 2860583fe840 ("ipv4: Kill rt->fi")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Uwe Kleine-König [Thu, 25 May 2017 20:54:53 +0000 (22:54 +0200)]
net: ethernet: ax88796: don't call free_irq without request_irq first
The function ax_init_dev (which is called only from the driver's .probe
function) calls free_irq in the error path without having requested the
irq in the first place. So drop the free_irq call in the error path.
Fixes: 825a2ff1896e ("AX88796 network driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Peter Dawson [Thu, 25 May 2017 20:35:18 +0000 (06:35 +1000)]
ip6_tunnel, ip6_gre: fix setting of DSCP on encapsulated packets
This fix addresses two problems in the way the DSCP field is formulated
on the encapsulating header of IPv6 tunnels.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195661
1) The IPv6 tunneling code was manipulating the DSCP field of the
encapsulating packet using the 32b flowlabel. Since the flowlabel is
only the lower 20b it was incorrect to assume that the upper 12b
containing the DSCP and ECN fields would remain intact when formulating
the encapsulating header. This fix handles the 'inherit' and
'fixed-value' DSCP cases explicitly using the extant dsfield u8 variable.
2) The use of INET_ECN_encapsulate(0, dsfield) in ip6_tnl_xmit was
incorrect and resulted in the DSCP value always being set to 0.
Commit
90427ef5d2a4 ("ipv6: fix flow labels when the traffic class
is non-0") caused the regression by masking out the flowlabel
which exposed the incorrect handling of the DSCP portion of the
flowlabel in ip6_tunnel and ip6_gre.
Fixes: 90427ef5d2a4 ("ipv6: fix flow labels when the traffic class is non-0")
Signed-off-by: Peter Dawson <peter.a.dawson@boeing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Thu, 25 May 2017 17:14:56 +0000 (19:14 +0200)]
sctp: fix ICMP processing if skb is non-linear
sometimes ICMP replies to INIT chunks are ignored by the client, even if
the encapsulated SCTP headers match an open socket. This happens when the
ICMP packet is carried by a paged skb: use skb_header_pointer() to read
packet contents beyond the SCTP header, so that chunk header and initiate
tag are validated correctly.
v2:
- don't use skb_header_pointer() to read the transport header, since
icmp_socket_deliver() already puts these 8 bytes in the linear area.
- change commit message to make specific reference to INIT chunks.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
linzhang [Thu, 25 May 2017 06:07:18 +0000 (14:07 +0800)]
net: llc: add lock_sock in llc_ui_bind to avoid a race condition
There is a race condition in llc_ui_bind if two or more processes/threads
try to bind a same socket.
If more processes/threads bind a same socket success that will lead to
two problems, one is this action is not what we expected, another is
will lead to kernel in unstable status or oops(in my simple test case,
cause llc2.ko can't unload).
The current code is test SOCK_ZAPPED bit to avoid a process to
bind a same socket twice but that is can't avoid more processes/threads
try to bind a same socket at the same time.
So, add lock_sock in llc_ui_bind like others, such as llc_ui_connect.
Signed-off-by: Lin Zhang <xiaolou4617@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 26 May 2017 18:05:22 +0000 (11:05 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A collection of fixes that should go into this series. This contains:
- A set of NVMe fixes, pulled from Christoph. This includes a set of
fixes for the fiber channel bits from James Smart, rdma queue depth
fix from Marta, controller removal fixes from Ming, and some more
APST quirk updates from Andy.
- A blk-mq debugfs fix from Bart, fixing a problem with the
untangling of the sysfs and debugfs blk-mq bits that was added in
this series.
- Error code fix in add_partition() from Dan.
- A small series of fixes for the new blk-throttle code from Shaohua"
* 'for-linus' of git://git.kernel.dk/linux-block: (21 commits)
blk-mq: Only register debugfs attributes for blk-mq queues
nvme: Quirk APST on Intel 600P/P3100 devices
nvme: only setup block integrity if supported by the driver
nvme: replace is_flags field in nvme_ctrl_ops with a flags field
nvme-pci: consistencly use ctrl->device for logging
partitions/msdos: FreeBSD UFS2 file systems are not recognized
block: fix an error code in add_partition()
blk-throttle: force user to configure all settings for io.low
blk-throttle: respect 0 bps/iops settings for io.low
blk-throttle: output some debug info in trace
blk-throttle: add hierarchy support for latency target and idle time
nvme_fc: remove extra controller reference taken on reconnect
nvme_fc: correct nvme status set on abort
nvme_fc: set logging level on resets/deletes
nvme_fc: revise comment on teardown
nvme_fc: Support ctrl_loss_tmo
nvme_fc: get rid of local reconnect_delay
blk-mq: remove blk_mq_abort_requeue_list()
nvme: avoid to use blk_mq_abort_requeue_list()
nvme: use blk_mq_start_hw_queues() in nvme_kill_queues()
...
Linus Torvalds [Fri, 26 May 2017 17:51:18 +0000 (10:51 -0700)]
Merge tag 'pci-v4.12-fixes-1' of git://git./linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- fix PCI_ENDPOINT build error (merged for v4.12)
- fix Switchtec driver (merged for v4.12)
- fix imx6 config read timeouts, fallout from changing to non-postable
reads
- add PM "needs_resume" flag for i915 suspend issue
* tag 'pci-v4.12-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI/PM: Add needs_resume flag to avoid suspend complete optimization
PCI: imx6: Fix config read timeout handling
switchtec: Fix minor bug with partition ID register
switchtec: Use new cdev_device_add() helper function
PCI: endpoint: Make PCI_ENDPOINT depend on HAS_DMA
Linus Torvalds [Fri, 26 May 2017 16:35:22 +0000 (09:35 -0700)]
Merge tag 'ceph-for-4.12-rc3' of git://github.com/ceph/ceph-client
Pul ceph fixes from Ilya Dryomov:
"A bunch of make W=1 and static checker fixups, a RECONNECT_SEQ
messenger patch from Zheng and Luis' fallocate fix"
* tag 'ceph-for-4.12-rc3' of git://github.com/ceph/ceph-client:
ceph: check that the new inode size is within limits in ceph_fallocate()
libceph: cleanup old messages according to reconnect seq
libceph: NULL deref on crush_decode() error path
libceph: fix error handling in process_one_ticket()
libceph: validate blob_struct_v in process_one_ticket()
libceph: drop version variable from ceph_monmap_decode()
libceph: make ceph_msg_data_advance() return void
libceph: use kbasename() and kill ceph_file_part()
Linus Torvalds [Fri, 26 May 2017 16:05:35 +0000 (09:05 -0700)]
Merge tag 'mmc-v4.12-rc2' of git://git./linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"This contains fixes to make the WiFi work again for the ARM64 Hikey
board.
Together with a couple of DTS updates for the Hikey board we have also
extended the mmc pwrseq_simple, to support a new power-off-delay-us DT
property, as that was required to enable a graceful power off sequence
for the WiFi chip"
* tag 'mmc-v4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
arm64: dts: hikey: Fix WiFi support
arm64: dts: hi6220: Move board data from the dwmmc nodes to hikey dts
arm64: dts: hikey: Add the SYS_5V and the VDD_3V3 regulators
arm64: dts: hi6220: Move the fixed_5v_hub regulator to the hikey dts
arm64: dts: hikey: Add clock for the pmic mfd
mfd: dts: hi655x: Add clock binding for the pmic
mmc: pwrseq_simple: Parse DTS for the power-off-delay-us property
mmc: dt: pwrseq-simple: Invent power-off-delay-us
Linus Torvalds [Fri, 26 May 2017 16:03:09 +0000 (09:03 -0700)]
Merge tag 'sound-4.12-rc3' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This contains a few HD-audio device-specific quirks and an endianess
fix for USB-audio, as well as the update of quirk model list document.
All fixes are small and trivial.
The document update could have been postponed, but it's a good thing
for user and has absolutely zero risk of breakage, so included here"
* tag 'sound-4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - apply STAC_9200_DELL_M22 quirk for Dell Latitude D430
ALSA: hda - Update the list of quirk models
ALSA: hda - Provide dual-codecs model option for a few Realtek codecs
ALSA: hda - Apply dual-codec quirk for MSI Z270-Gaming mobo
ALSA: hda - No loopback on ALC299 codec
ALSA: usb-audio: fix Amanero Combo384 quirk on big-endian hosts
Linus Torvalds [Fri, 26 May 2017 15:54:06 +0000 (08:54 -0700)]
Merge tag 'drm-fixes-for-v4.12-rc3' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Not a whole lot happening here, a set of amdgpu fixes and one core
deadlock fix, and some misc drivers fixes"
* tag 'drm-fixes-for-v4.12-rc3' of git://people.freedesktop.org/~airlied/linux:
drm/amdgpu: fix null point error when rmmod amdgpu.
drm/amd/powerplay: fix a signedness bugs
drm/amdgpu: fix NULL pointer panic of emit_gds_switch
drm/radeon: Unbreak HPD handling for r600+
drm/amd/powerplay/smu7: disable mclk switching for high refresh rates
drm/amd/powerplay/smu7: add vblank check for mclk switching (v2)
drm/radeon/ci: disable mclk switching for high refresh rates (v2)
drm/amdgpu/ci: disable mclk switching for high refresh rates (v2)
drm/amdgpu: fix fundamental suspend/resume issue
drm/gma500/psb: Actually use VBT mode when it is found
drm: Fix deadlock retry loop in page_flip_ioctl
drm: qxl: Delay entering atomic context during cursor update
drm/radeon: Fix oops upon driver load on PowerXpress laptops
Christoph Hellwig [Sat, 20 May 2017 16:59:54 +0000 (18:59 +0200)]
PCI/msi: fix the pci_alloc_irq_vectors_affinity stub
We need to return an error for any call that asks for MSI / MSI-X
vectors only, so that non-trivial fallback logic can work properly.
Also valid dev->irq and use the "correct" errno value based on feedback
from Linus.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Fixes: aff17164 ("PCI: Provide sensible IRQ vector alloc/free routines")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jens Axboe [Fri, 26 May 2017 15:11:19 +0000 (09:11 -0600)]
Merge branch 'nvme-4.12' of git://git.infradead.org/nvme into for-linus
Christoph writes:
"A couple of fixes for the next rc on the nvme front. Various FC fixes
from James, controller removal fixes from Ming (including a block layer
patch), a APST related device quirk from Andy, a RDMA fix for small
queue depth device from Marta, as well as fixes for the lack of
metadata support in non-PCIe drivers and the printk logging format from
me."
Bart Van Assche [Thu, 25 May 2017 23:38:06 +0000 (16:38 -0700)]
blk-mq: Only register debugfs attributes for blk-mq queues
The code in blk-mq-debugfs.c assumes that it is working on a blk-mq
queue and is not intended to work on a blk-sq queue. Hence only
register blk-mq debugfs attributes for blk-mq queues.
Fixes: commit 9c1051aacde8 ("blk-mq: untangle debugfs and sysfs")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Andy Lutomirski [Wed, 24 May 2017 22:06:31 +0000 (15:06 -0700)]
nvme: Quirk APST on Intel 600P/P3100 devices
They have known firmware bugs. A fix is apparently in the works --
once fixed firmware is available, someone from Intel (Hi, Keith!)
can adjust the quirk accordingly.
Cc: stable@vger.kernel.org # v4.11
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: Mario Limonciello <mario_limonciello@dell.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Christoph Hellwig [Sat, 20 May 2017 13:14:45 +0000 (15:14 +0200)]
nvme: only setup block integrity if supported by the driver
Currently only the PCIe driver supports metadata, so we should not claim
integrity support for the other drivers. This prevents nasty crashes
with targets that advertise metadata support on fabrics.
Also use the opportunity to factor out some code into a separate helper
that isn't even compiled if CONFIG_BLK_DEV_INTEGRITY is disabled.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Christoph Hellwig [Sat, 20 May 2017 13:14:44 +0000 (15:14 +0200)]
nvme: replace is_flags field in nvme_ctrl_ops with a flags field
So that we can have more flags for transport-specific behavior.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Christoph Hellwig [Sat, 20 May 2017 13:14:43 +0000 (15:14 +0200)]
nvme-pci: consistencly use ctrl->device for logging
This is what most of the code already does and gives much more useful
prefixes than the device embedded in the pci_dev.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Dave Airlie [Fri, 26 May 2017 01:51:55 +0000 (11:51 +1000)]
Merge branch 'drm-fixes-4.12' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
A bunch of bug fixes:
- Fix display flickering on some chips at high refresh rates
- suspend/resume fix
- hotplug fix
- a couple of segfault fixes for certain cases
* 'drm-fixes-4.12' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: fix null point error when rmmod amdgpu.
drm/amd/powerplay: fix a signedness bugs
drm/amdgpu: fix NULL pointer panic of emit_gds_switch
drm/radeon: Unbreak HPD handling for r600+
drm/amd/powerplay/smu7: disable mclk switching for high refresh rates
drm/amd/powerplay/smu7: add vblank check for mclk switching (v2)
drm/radeon/ci: disable mclk switching for high refresh rates (v2)
drm/amdgpu/ci: disable mclk switching for high refresh rates (v2)
drm/amdgpu: fix fundamental suspend/resume issue
Dave Airlie [Fri, 26 May 2017 01:51:28 +0000 (11:51 +1000)]
Merge tag 'drm-misc-fixes-2017-05-25' of git://anongit.freedesktop.org/git/drm-misc into drm-fixes
Core Changes:
- Don't drop vblank reference more than once in cases of ww retry (Daniel)
Driver Changes:
- radeon: Fix oops during radeon probe trying to reference wrong device (Lukas)
- qxl: Avoid sleeping while in atomic context on cursor update (Gabriel)
- gma500: Use VBT mode instead of pre-programmed mode for LVDS (Patrik)
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
* tag 'drm-misc-fixes-2017-05-25' of git://anongit.freedesktop.org/git/drm-misc:
drm/gma500/psb: Actually use VBT mode when it is found
drm: Fix deadlock retry loop in page_flip_ioctl
drm: qxl: Delay entering atomic context during cursor update
drm/radeon: Fix oops upon driver load on PowerXpress laptops
Nithin Sujir [Thu, 25 May 2017 02:45:17 +0000 (19:45 -0700)]
bonding: Don't update slave->link until ready to commit
In the loadbalance arp monitoring scheme, when a slave link change is
detected, the slave->link is immediately updated and slave_state_changed
is set. Later down the function, the rtnl_lock is acquired and the
changes are committed, updating the bond link state.
However, the acquisition of the rtnl_lock can fail. The next time the
monitor runs, since slave->link is already updated, it determines that
link is unchanged. This results in the bond link state permanently out
of sync with the slave link.
This patch modifies bond_loadbalance_arp_mon() to handle link changes
identical to bond_ab_arp_{inspect/commit}(). The new link state is
maintained in slave->new_link until we're ready to commit at which point
it's copied into slave->link.
NOTE: miimon_{inspect/commit}() has a more complex state machine
requiring the use of the bond_{propose,commit}_link_state() functions
which maintains the intermediate state in slave->link_new_state. The arp
monitors don't require that.
Testing: This bug is very easy to reproduce with the following steps.
1. In a loop, toggle a slave link of a bond slave interface.
2. In a separate loop, do ifconfig up/down of an unrelated interface to
create contention for rtnl_lock.
Within a few iterations, the bond link goes out of sync with the slave
link.
Signed-off-by: Nithin Nayak Sujir <nsujir@tintri.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: Jay Vosburgh <jay.vosburgh@canonical.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Daney [Wed, 24 May 2017 23:35:49 +0000 (16:35 -0700)]
test_bpf: Add a couple of tests for BPF_JSGE.
Some JITs can optimize comparisons with zero. Add a couple of
BPF_JSGE tests against immediate zero.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 25 May 2017 17:44:29 +0000 (13:44 -0400)]
Merge branch 'bpf-fixes'
Daniel Borkmann says:
====================
Various BPF fixes
Follow-up to fix incorrect pruning when alignment tracking is
in use and to properly clear regs after call to not leave stale
data behind, also a fix that adds bpf_clone_redirect to the
bpf_helper_changes_pkt_data helper and exposes correct map_flags
for lpm map into fdinfo. For details, please see individual
patches.
v1 -> v2:
- Reworked first patch so that env->strict_alignment is the
final indicator on whether we have to deal with strict
alignment rather than having CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
checks on various locations, so only checking env->strict_alignment
is sufficient after that. Thanks for spotting, Dave!
- Added patch 3 and 4.
- Rest as is.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 24 May 2017 23:05:09 +0000 (01:05 +0200)]
bpf: add various verifier test cases
This patch adds various verifier test cases:
1) A test case for the pruning issue when tracking alignment
is used.
2) Various PTR_TO_MAP_VALUE_OR_NULL tests to make sure pointer
arithmetic turns such register into UNKNOWN_VALUE type.
3) Test cases for the special treatment of LD_ABS/LD_IND to
make sure verifier doesn't break calling convention here.
Latter is needed, since f.e. arm64 JIT uses r1 - r5 for
storing temporary data, so they really must be marked as
NOT_INIT.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 24 May 2017 23:05:08 +0000 (01:05 +0200)]
bpf: fix wrong exposure of map_flags into fdinfo for lpm
trie_alloc() always needs to have BPF_F_NO_PREALLOC passed in via
attr->map_flags, since it does not support preallocation yet. We
check the flag, but we never copy the flag into trie->map.map_flags,
which is later on exposed into fdinfo and used by loaders such as
iproute2. Latter uses this in bpf_map_selfcheck_pinned() to test
whether a pinned map has the same spec as the one from the BPF obj
file and if not, bails out, which is currently the case for lpm
since it exposes always 0 as flags.
Also copy over flags in array_map_alloc() and stack_map_alloc().
They always have to be 0 right now, but we should make sure to not
miss to copy them over at a later point in time when we add actual
flags for them to use.
Fixes: b95a5c4db09b ("bpf: add a longest prefix match trie map implementation")
Reported-by: Jarno Rajahalme <jarno@covalent.io>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 24 May 2017 23:05:07 +0000 (01:05 +0200)]
bpf: add bpf_clone_redirect to bpf_helper_changes_pkt_data
The bpf_clone_redirect() still needs to be listed in
bpf_helper_changes_pkt_data() since we call into
bpf_try_make_head_writable() from there, thus we need
to invalidate prior pkt regs as well.
Fixes: 36bbef52c7eb ("bpf: direct packet write and access for helpers for clsact progs")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 24 May 2017 23:05:06 +0000 (01:05 +0200)]
bpf: properly reset caller saved regs after helper call and ld_abs/ind
Currently, after performing helper calls, we clear all caller saved
registers, that is r0 - r5 and fill r0 depending on struct bpf_func_proto
specification. The way we reset these regs can affect pruning decisions
in later paths, since we only reset register's imm to 0 and type to
NOT_INIT. However, we leave out clearing of other variables such as id,
min_value, max_value, etc, which can later on lead to pruning mismatches
due to stale data.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 24 May 2017 23:05:05 +0000 (01:05 +0200)]
bpf: fix incorrect pruning decision when alignment must be tracked
Currently, when we enforce alignment tracking on direct packet access,
the verifier lets the following program pass despite doing a packet
write with unaligned access:
0: (61) r2 = *(u32 *)(r1 +76)
1: (61) r3 = *(u32 *)(r1 +80)
2: (61) r7 = *(u32 *)(r1 +8)
3: (bf) r0 = r2
4: (07) r0 += 14
5: (25) if r7 > 0x1 goto pc+4
R0=pkt(id=0,off=14,r=0) R1=ctx R2=pkt(id=0,off=0,r=0)
R3=pkt_end R7=inv,min_value=0,max_value=1 R10=fp
6: (2d) if r0 > r3 goto pc+1
R0=pkt(id=0,off=14,r=14) R1=ctx R2=pkt(id=0,off=0,r=14)
R3=pkt_end R7=inv,min_value=0,max_value=1 R10=fp
7: (63) *(u32 *)(r0 -4) = r0
8: (b7) r0 = 0
9: (95) exit
from 6 to 8:
R0=pkt(id=0,off=14,r=0) R1=ctx R2=pkt(id=0,off=0,r=0)
R3=pkt_end R7=inv,min_value=0,max_value=1 R10=fp
8: (b7) r0 = 0
9: (95) exit
from 5 to 10:
R0=pkt(id=0,off=14,r=0) R1=ctx R2=pkt(id=0,off=0,r=0)
R3=pkt_end R7=inv,min_value=2 R10=fp
10: (07) r0 += 1
11: (05) goto pc-6
6: safe <----- here, wrongly found safe
processed 15 insns
However, if we enforce a pruning mismatch by adding state into r8
which is then being mismatched in states_equal(), we find that for
the otherwise same program, the verifier detects a misaligned packet
access when actually walking that path:
0: (61) r2 = *(u32 *)(r1 +76)
1: (61) r3 = *(u32 *)(r1 +80)
2: (61) r7 = *(u32 *)(r1 +8)
3: (b7) r8 = 1
4: (bf) r0 = r2
5: (07) r0 += 14
6: (25) if r7 > 0x1 goto pc+4
R0=pkt(id=0,off=14,r=0) R1=ctx R2=pkt(id=0,off=0,r=0)
R3=pkt_end R7=inv,min_value=0,max_value=1
R8=imm1,min_value=1,max_value=1,min_align=1 R10=fp
7: (2d) if r0 > r3 goto pc+1
R0=pkt(id=0,off=14,r=14) R1=ctx R2=pkt(id=0,off=0,r=14)
R3=pkt_end R7=inv,min_value=0,max_value=1
R8=imm1,min_value=1,max_value=1,min_align=1 R10=fp
8: (63) *(u32 *)(r0 -4) = r0
9: (b7) r0 = 0
10: (95) exit
from 7 to 9:
R0=pkt(id=0,off=14,r=0) R1=ctx R2=pkt(id=0,off=0,r=0)
R3=pkt_end R7=inv,min_value=0,max_value=1
R8=imm1,min_value=1,max_value=1,min_align=1 R10=fp
9: (b7) r0 = 0
10: (95) exit
from 6 to 11:
R0=pkt(id=0,off=14,r=0) R1=ctx R2=pkt(id=0,off=0,r=0)
R3=pkt_end R7=inv,min_value=2
R8=imm1,min_value=1,max_value=1,min_align=1 R10=fp
11: (07) r0 += 1
12: (b7) r8 = 0
13: (05) goto pc-7 <----- mismatch due to r8
7: (2d) if r0 > r3 goto pc+1
R0=pkt(id=0,off=15,r=15) R1=ctx R2=pkt(id=0,off=0,r=15)
R3=pkt_end R7=inv,min_value=2
R8=imm0,min_value=0,max_value=0,min_align=
2147483648 R10=fp
8: (63) *(u32 *)(r0 -4) = r0
misaligned packet access off 2+15+-4 size 4
The reason why we fail to see it in states_equal() is that the
third test in compare_ptrs_to_packet() ...
if (old->off <= cur->off &&
old->off >= old->range && cur->off >= cur->range)
return true;
... will let the above pass. The situation we run into is that
old->off <= cur->off (14 <= 15), meaning that prior walked paths
went with smaller offset, which was later used in the packet
access after successful packet range check and found to be safe
already.
For example: Given is R0=pkt(id=0,off=0,r=0). Adding offset 14
as in above program to it, results in R0=pkt(id=0,off=14,r=0)
before the packet range test. Now, testing this against R3=pkt_end
with 'if r0 > r3 goto out' will transform R0 into R0=pkt(id=0,off=14,r=14)
for the case when we're within bounds. A write into the packet
at offset *(u32 *)(r0 -4), that is, 2 + 14 -4, is valid and
aligned (2 is for NET_IP_ALIGN). After processing this with
all fall-through paths, we later on check paths from branches.
When the above skb->mark test is true, then we jump near the
end of the program, perform r0 += 1, and jump back to the
'if r0 > r3 goto out' test we've visited earlier already. This
time, R0 is of type R0=pkt(id=0,off=15,r=0), and we'll prune
that part because this time we'll have a larger safe packet
range, and we already found that with off=14 all further insn
were already safe, so it's safe as well with a larger off.
However, the problem is that the subsequent write into the packet
with 2 + 15 -4 is then unaligned, and not caught by the alignment
tracking. Note that min_align, aux_off, and aux_off_align were
all 0 in this example.
Since we cannot tell at this time what kind of packet access was
performed in the prior walk and what minimal requirements it has
(we might do so in the future, but that requires more complexity),
fix it to disable this pruning case for strict alignment for now,
and let the verifier do check such paths instead. With that applied,
the test cases pass and reject the program due to misalignment.
Fixes: d1174416747d ("bpf: Track alignment of register values in the verifier.")
Reference: http://patchwork.ozlabs.org/patch/761909/
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ihar Hrachyshka [Wed, 24 May 2017 22:19:35 +0000 (15:19 -0700)]
arp: fixed -Wuninitialized compiler warning
Commit
7d472a59c0e5ec117220a05de6b370447fb6cb66 ("arp: always override
existing neigh entries with gratuitous ARP") introduced a compiler
warning:
net/ipv4/arp.c:880:35: warning: 'addr_type' may be used uninitialized in
this function [-Wmaybe-uninitialized]
While the code logic seems to be correct and doesn't allow the variable
to be used uninitialized, and the warning is not consistently
reproducible, it's still worth fixing it for other people not to waste
time looking at the warning in case it pops up in the build environment.
Yes, compiler is probably at fault, but we will need to accommodate.
Fixes: 7d472a59c0e5 ("arp: always override existing neigh entries with gratuitous ARP")
Signed-off-by: Ihar Hrachyshka <ihrachys@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Wang [Wed, 24 May 2017 16:59:31 +0000 (09:59 -0700)]
tcp: avoid fastopen API to be used on AF_UNSPEC
Fastopen API should be used to perform fastopen operations on the TCP
socket. It does not make sense to use fastopen API to perform disconnect
by calling it with AF_UNSPEC. The fastopen data path is also prone to
race conditions and bugs when using with AF_UNSPEC.
One issue reported and analyzed by Vegard Nossum is as follows:
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Thread A: Thread B:
------------------------------------------------------------------------
sendto()
- tcp_sendmsg()
- sk_stream_memory_free() = 0
- goto wait_for_sndbuf
- sk_stream_wait_memory()
- sk_wait_event() // sleep
| sendto(flags=MSG_FASTOPEN, dest_addr=AF_UNSPEC)
| - tcp_sendmsg()
| - tcp_sendmsg_fastopen()
| - __inet_stream_connect()
| - tcp_disconnect() //because of AF_UNSPEC
| - tcp_transmit_skb()// send RST
| - return 0; // no reconnect!
| - sk_stream_wait_connect()
| - sock_error()
| - xchg(&sk->sk_err, 0)
| - return -ECONNRESET
- ... // wake up, see sk->sk_err == 0
- skb_entail() on TCP_CLOSE socket
If the connection is reopened then we will send a brand new SYN packet
after thread A has already queued a buffer. At this point I think the
socket internal state (sequence numbers etc.) becomes messed up.
When the new connection is closed, the FIN-ACK is rejected because the
sequence number is outside the window. The other side tries to
retransmit,
but __tcp_retransmit_skb() calls tcp_trim_head() on an empty skb which
corrupts the skb data length and hits a BUG() in copy_and_csum_bits().
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Hence, this patch adds a check for AF_UNSPEC in the fastopen data path
and return EOPNOTSUPP to user if such case happens.
Fixes: cf60af03ca4e7 ("tcp: Fast Open client - sendmsg(MSG_FASTOPEN)")
Reported-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roman Kapl [Wed, 24 May 2017 08:22:22 +0000 (10:22 +0200)]
net: move somaxconn init from sysctl code
The default value for somaxconn is set in sysctl_core_net_init(), but this
function is not called when kernel is configured without CONFIG_SYSCTL.
This results in the kernel not being able to accept TCP connections,
because the backlog has zero size. Usually, the user ends up with:
"TCP: request_sock_TCP: Possible SYN flooding on port 7. Dropping request. Check SNMP counters."
If SYN cookies are not enabled the connection is rejected.
Before
ef547f2ac16 (tcp: remove max_qlen_log), the effects were less
severe, because the backlog was always at least eight slots long.
Signed-off-by: Roman Kapl <roman.kapl@sysgo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gustavo A. R. Silva [Tue, 23 May 2017 23:18:37 +0000 (18:18 -0500)]
net: fix potential null pointer dereference
Add null check to avoid a potential null pointer dereference.
Addresses-Coverity-ID:
1408831
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rex Zhu [Mon, 22 May 2017 05:11:41 +0000 (13:11 +0800)]
drm/amdgpu: fix null point error when rmmod amdgpu.
this bug happened when amdgpu load failed.
[ 75.740951] BUG: unable to handle kernel paging request at
00000000000031c0
[ 75.748167] IP: [<
ffffffffa064a0e0>] amdgpu_fbdev_restore_mode+0x20/0x60 [amdgpu]
[ 75.755774] PGD 0
[ 75.759185] Oops: 0000 [#1] SMP
[ 75.762408] Modules linked in: amdgpu(OE-) ttm(OE) drm_kms_helper(OE) drm(OE) i2c_algo_bit(E) fb_sys_fops(E) syscopyarea(E) sysfillrect(E) sysimgblt(E) rpcsec_gss_krb5(E) nfsv4(E) nfs(E) fscache(E) eeepc_wmi(E) asus_wmi(E) sparse_keymap(E) intel_rapl(E) snd_hda_codec_hdmi(E) snd_hda_codec_realtek(E) snd_hda_codec_generic(E) snd_hda_intel(E) snd_hda_codec(E) snd_hda_core(E) x86_pkg_temp_thermal(E) intel_powerclamp(E) snd_hwdep(E) snd_pcm(E) snd_seq_midi(E) coretemp(E) kvm_intel(E) snd_seq_midi_event(E) snd_rawmidi(E) kvm(E) snd_seq(E) joydev(E) snd_seq_device(E) snd_timer(E) irqbypass(E) crct10dif_pclmul(E) crc32_pclmul(E) mei_me(E) ghash_clmulni_intel(E) snd(E) aesni_intel(E) mei(E) soundcore(E) aes_x86_64(E) shpchp(E) serio_raw(E) lrw(E) acpi_pad(E) gf128mul(E) glue_helper(E) ablk_helper(E) mac_hid(E)
[ 75.835574] cryptd(E) parport_pc(E) ppdev(E) lp(E) nfsd(E) parport(E) auth_rpcgss(E) nfs_acl(E) lockd(E) grace(E) sunrpc(E) autofs4(E) hid_generic(E) usbhid(E) mxm_wmi(E) psmouse(E) e1000e(E) ptp(E) pps_core(E) ahci(E) libahci(E) wmi(E) video(E) i2c_hid(E) hid(E)
[ 75.858489] CPU: 5 PID: 1603 Comm: rmmod Tainted: G OE 4.9.0-custom #2
[ 75.866183] Hardware name: System manufacturer System Product Name/Z170-A, BIOS 0901 08/31/2015
[ 75.875050] task:
ffff88045d1bbb80 task.stack:
ffffc90002de4000
[ 75.881094] RIP: 0010:[<
ffffffffa064a0e0>] [<
ffffffffa064a0e0>] amdgpu_fbdev_restore_mode+0x20/0x60 [amdgpu]
[ 75.891238] RSP: 0018:
ffffc90002de7d48 EFLAGS:
00010286
[ 75.896648] RAX:
0000000000000000 RBX:
0000000000000000 RCX:
0000000000000001
[ 75.903933] RDX:
0000000000000000 RSI:
ffff88045d1bbb80 RDI:
0000000000000286
[ 75.911183] RBP:
ffffc90002de7d50 R08:
0000000000000502 R09:
0000000000000004
[ 75.918449] R10:
0000000000000000 R11:
0000000000000001 R12:
ffff880464bf0000
[ 75.925675] R13:
ffffffffa0853000 R14:
0000000000000000 R15:
0000564e44f88210
[ 75.932980] FS:
00007f13d5400700(0000) GS:
ffff880476540000(0000) knlGS:
0000000000000000
[ 75.941238] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 75.947088] CR2:
00000000000031c0 CR3:
000000045fd0b000 CR4:
00000000003406e0
[ 75.954332] DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
[ 75.961566] DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
[ 75.968834] Stack:
[ 75.970881]
ffff880464bf0000 ffffc90002de7d60 ffffffffa0636592 ffffc90002de7d80
[ 75.978454]
ffffffffa059015f ffff880464bf0000 ffff880464bf0000 ffffc90002de7da8
[ 75.986076]
ffffffffa0595216 ffff880464bf0000 ffff880460f4d000 ffffffffa0853000
[ 75.993692] Call Trace:
[ 75.996177] [<
ffffffffa0636592>] amdgpu_driver_lastclose_kms+0x12/0x20 [amdgpu]
[ 76.003700] [<
ffffffffa059015f>] drm_lastclose+0x2f/0xd0 [drm]
[ 76.009777] [<
ffffffffa0595216>] drm_dev_unregister+0x16/0xd0 [drm]
[ 76.016255] [<
ffffffffa0595944>] drm_put_dev+0x34/0x70 [drm]
[ 76.022139] [<
ffffffffa062f365>] amdgpu_pci_remove+0x15/0x20 [amdgpu]
[ 76.028800] [<
ffffffff81416499>] pci_device_remove+0x39/0xc0
[ 76.034661] [<
ffffffff81531caa>] __device_release_driver+0x9a/0x140
[ 76.041121] [<
ffffffff81531e58>] driver_detach+0xb8/0xc0
[ 76.046575] [<
ffffffff81530c95>] bus_remove_driver+0x55/0xd0
[ 76.052401] [<
ffffffff815325fc>] driver_unregister+0x2c/0x50
[ 76.058244] [<
ffffffff81416289>] pci_unregister_driver+0x29/0x90
[ 76.064466] [<
ffffffffa0596c5e>] drm_pci_exit+0x9e/0xb0 [drm]
[ 76.070507] [<
ffffffffa0796d71>] amdgpu_exit+0x1c/0x32 [amdgpu]
[ 76.076609] [<
ffffffff81104810>] SyS_delete_module+0x1a0/0x200
[ 76.082627] [<
ffffffff810e2b1a>] ? rcu_eqs_enter.isra.36+0x4a/0x50
[ 76.089001] [<
ffffffff8100392e>] do_syscall_64+0x6e/0x180
[ 76.094583] [<
ffffffff817e1d2f>] entry_SYSCALL64_slow_path+0x25/0x25
[ 76.101114] Code: 94 c0 c3 31 c0 5d c3 0f 1f 40 00 0f 1f 44 00 00 55 31 c0 48 89 e5 53 48 89 fb 48 c7 c7 1d 21 84 a0 e8 ab 77 b3 e0 e8 fc 8b d7 e0 <48> 8b bb c0 31 00 00 48 85 ff 74 09 e8 ff eb fc ff 85 c0 75 03
[ 76.121432] RIP [<
ffffffffa064a0e0>] amdgpu_fbdev_restore_mode+0x20/0x60 [amdgpu]
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Eric Garver [Tue, 23 May 2017 22:37:27 +0000 (18:37 -0400)]
geneve: fix fill_info when using collect_metadata
Since
9b4437a5b870 ("geneve: Unify LWT and netdev handling.") fill_info
does not return UDP_ZERO_CSUM6_RX when using COLLECT_METADATA. This is
because it uses ip_tunnel_info_af() with the device level info, which is
not valid for COLLECT_METADATA.
Fix by checking for the presence of the actual sockets.
Fixes: 9b4437a5b870 ("geneve: Unify LWT and netdev handling.")
Signed-off-by: Eric Garver <e@erig.me>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Kara [Thu, 18 May 2017 23:36:24 +0000 (16:36 -0700)]
xfs: Move handling of missing page into one place in xfs_find_get_desired_pgoff()
Currently several places in xfs_find_get_desired_pgoff() handle the case
of a missing page. Make them all handled in one place after the loop has
terminated.
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Jan Kara [Thu, 18 May 2017 23:36:23 +0000 (16:36 -0700)]
xfs: Fix off-by-in in loop termination in xfs_find_get_desired_pgoff()
There is an off-by-one error in loop termination conditions in
xfs_find_get_desired_pgoff() since 'end' may index a page beyond end of
desired range if 'endoff' is page aligned. It doesn't have any visible
effects but still it is good to fix it.
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Jan Kara [Thu, 18 May 2017 23:36:22 +0000 (16:36 -0700)]
xfs: Fix missed holes in SEEK_HOLE implementation
XFS SEEK_HOLE implementation could miss a hole in an unwritten extent as
can be seen by the following command:
xfs_io -c "falloc 0 256k" -c "pwrite 0 56k" -c "pwrite 128k 8k"
-c "seek -h 0" file
wrote 57344/57344 bytes at offset 0
56 KiB, 14 ops; 0.0000 sec (49.312 MiB/sec and 12623.9856 ops/sec)
wrote 8192/8192 bytes at offset 131072
8 KiB, 2 ops; 0.0000 sec (70.383 MiB/sec and 18018.0180 ops/sec)
Whence Result
HOLE 139264
Where we can see that hole at offset 56k was just ignored by SEEK_HOLE
implementation. The bug is in xfs_find_get_desired_pgoff() which does
not properly detect the case when pages are not contiguous.
Fix the problem by properly detecting when found page has larger offset
than expected.
CC: stable@vger.kernel.org
Fixes: d126d43f631f996daeee5006714fed914be32368
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Eryu Guan [Tue, 23 May 2017 15:30:46 +0000 (08:30 -0700)]
xfs: fix off-by-one on max nr_pages in xfs_find_get_desired_pgoff()
xfs_find_get_desired_pgoff() is used to search for offset of hole or
data in page range [index, end] (both inclusive), and the max number
of pages to search should be at least one, if end == index.
Otherwise the only page is missed and no hole or data is found,
which is not correct.
When block size is smaller than page size, this can be demonstrated
by preallocating a file with size smaller than page size and writing
data to the last block. E.g. run this xfs_io command on a 1k block
size XFS on x86_64 host.
# xfs_io -fc "falloc 0 3k" -c "pwrite 2k 1k" \
-c "seek -d 0" /mnt/xfs/testfile
wrote 1024/1024 bytes at offset 2048
1 KiB, 1 ops; 0.0000 sec (33.675 MiB/sec and 34482.7586 ops/sec)
Whence Result
DATA EOF
Data at offset 2k was missed, and lseek(2) returned ENXIO.
This is uncovered by generic/285 subtest 07 and 08 on ppc64 host,
where pagesize is 64k. Because a recent change to generic/285
reduced the preallocated file size to smaller than 64k.
Cc: stable@vger.kernel.org # v3.7+
Signed-off-by: Eryu Guan <eguan@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Eric Sandeen [Tue, 23 May 2017 02:54:10 +0000 (19:54 -0700)]
xfs: fix unaligned access in xfs_btree_visit_blocks
This structure copy was throwing unaligned access warnings on sparc64:
Kernel unaligned access at TPC[
1043c088] xfs_btree_visit_blocks+0x88/0xe0 [xfs]
xfs_btree_copy_ptrs does a memcpy, which avoids it.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Linus Torvalds [Thu, 25 May 2017 03:29:53 +0000 (20:29 -0700)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is quite a big update because it includes a rework of the lpfc
driver to separate the NVMe part from the FC part.
The reason for doing this is because two separate trees (the nvme and
scsi trees respectively) want to update the individual components and
this separation will prevent a really nasty cross tree entanglement by
the time we reach the next merge window.
The rest of the fixes are the usual minor sort with no significant
security implications"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (25 commits)
scsi: zero per-cmd private driver data for each MQ I/O
scsi: csiostor: fix use after free in csio_hw_use_fwconfig()
scsi: ufs: Clean up some rpm/spm level SysFS nodes upon remove
scsi: lpfc: fix build issue if NVME_FC_TARGET is not defined
scsi: lpfc: Fix NULL pointer dereference during PCI error recovery
scsi: lpfc: update version to 11.2.0.14
scsi: lpfc: Add MDS Diagnostic support.
scsi: lpfc: Fix NVMEI's handling of NVMET's PRLI response attributes
scsi: lpfc: Cleanup entry_repost settings on SLI4 queues
scsi: lpfc: Fix debugfs root inode "lpfc" not getting deleted on driver unload.
scsi: lpfc: Fix NVME I+T not registering NVME as a supported FC4 type
scsi: lpfc: Added recovery logic for running out of NVMET IO context resources
scsi: lpfc: Separate NVMET RQ buffer posting from IO resources SGL/iocbq/context
scsi: lpfc: Separate NVMET data buffer pool fir ELS/CT.
scsi: lpfc: Fix NMI watchdog assertions when running nvmet IOPS tests
scsi: lpfc: Fix NVMEI driver not decrementing counter causing bad rport state.
scsi: lpfc: Fix nvmet RQ resource needs for large block writes.
scsi: lpfc: Adding additional stats counters for nvme.
scsi: lpfc: Fix system crash when port is reset.
scsi: lpfc: Fix used-RPI accounting problem.
...
Dan Carpenter [Tue, 23 May 2017 05:13:45 +0000 (13:13 +0800)]
drm/amd/powerplay: fix a signedness bugs
Smatch complains about a signedness bug here:
vega10_hwmgr.c:4202 vega10_force_clock_level()
warn: always true condition '(i >= 0) => (0-u32max >= 0)'
Fixes: 7b52db39a4c2 ("drm/amd/powerplay: fix bug sclk/mclk
level can't be set on vega10.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Eric Huang <JinHuiEric.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Chunming Zhou [Thu, 11 May 2017 10:22:17 +0000 (18:22 +0800)]
drm/amdgpu: fix NULL pointer panic of emit_gds_switch
[ 338.384770] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 338.384817] IP: [< (null)>] (null)
[ 338.385505] RIP: 0010:[<
0000000000000000>] [< (null)>] (null)
[ 338.385950] Call Trace:
[ 338.385993] [<
ffffffffa05d2313>] ? amdgpu_vm_flush+0x283/0x400 [amdgpu]
[ 338.386025] [<
ffffffff811818d3>] ? printk+0x4d/0x4f
[ 338.386074] [<
ffffffffa05d4906>] amdgpu_ib_schedule+0x4a6/0x4d0 [amdgpu]
[ 338.386140] [<
ffffffffa0673e54>] amdgpu_job_run+0x64/0x180 [amdgpu]
[ 338.386203] [<
ffffffffa0672e09>] amd_sched_main+0x2e9/0x4a0 [amdgpu]
[ 338.386232] [<
ffffffff810bfce0>] ? prepare_to_wait_event+0x110/0x110
[ 338.386295] [<
ffffffffa0672b20>] ? amd_sched_select_entity+0xe0/0xe0 [amdgpu]
[ 338.386327] [<
ffffffff8109b423>] kthread+0xd3/0xf0
[ 338.386349] [<
ffffffff8109b350>] ? kthread_park+0x60/0x60
[ 338.386376] [<
ffffffff817e1ee5>] ret_from_fork+0x25/0x30
[ 338.386401] Code: Bad RIP value.
[ 338.386420] RIP [< (null)>] (null)
[ 338.386443] RSP <
ffffc90001bd7d40>
[ 338.386458] CR2:
0000000000000000
[ 338.398508] ---[ end trace
4c66fcdc74b9a0a2 ]---
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Lyude [Thu, 11 May 2017 23:31:12 +0000 (19:31 -0400)]
drm/radeon: Unbreak HPD handling for r600+
We end up reading the interrupt register for HPD5, and then writing it
to HPD6 which on systems without anything using HPD5 results in
permanently disabling hotplug on one of the display outputs after the
first time we acknowledge a hotplug interrupt from the GPU.
This code is really bad. But for now, let's just fix this. I will
hopefully have a large patch series to refactor all of this soon.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Lyude <lyude@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Thu, 11 May 2017 17:57:41 +0000 (13:57 -0400)]
drm/amd/powerplay/smu7: disable mclk switching for high refresh rates
Even if the vblank period would allow it, it still seems to
be problematic on some cards.
bug: https://bugs.freedesktop.org/show_bug.cgi?id=96868
Cc: stable@vger.kernel.org
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Thu, 11 May 2017 17:46:12 +0000 (13:46 -0400)]
drm/amd/powerplay/smu7: add vblank check for mclk switching (v2)
Check to make sure the vblank period is long enough to support
mclk switching.
v2: drop needless initial assignment (Nils)
bug: https://bugs.freedesktop.org/show_bug.cgi?id=96868
Cc: stable@vger.kernel.org
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Thu, 11 May 2017 17:14:14 +0000 (13:14 -0400)]
drm/radeon/ci: disable mclk switching for high refresh rates (v2)
Even if the vblank period would allow it, it still seems to
be problematic on some cards.
v2: fix logic inversion (Nils)
bug: https://bugs.freedesktop.org/show_bug.cgi?id=96868
Cc: stable@vger.kernel.org
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Thu, 11 May 2017 17:10:02 +0000 (13:10 -0400)]
drm/amdgpu/ci: disable mclk switching for high refresh rates (v2)
Even if the vblank period would allow it, it still seems to
be problematic on some cards.
v2: fix logic inversion (Nils)
bug: https://bugs.freedesktop.org/show_bug.cgi?id=96868
Cc: stable@vger.kernel.org
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
David S. Miller [Wed, 24 May 2017 20:27:22 +0000 (16:27 -0400)]
Merge branch 'q-in-q-checksums'
Daniel Borkmann says:
====================
BPF pruning follow-up
Follow-up to fix incorrect pruning when alignment tracking is
in use and to properly clear regs after call to not leave stale
data behind. For details, please see individual patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / openwrt / staging / blogic.git / log