ASoC: Mark Speyside widgets as ignoring suspend

Allow audio paths through the Speyside system to be kept active while the
system is suspended (for example, when on a voice call) by marking all the
external widgets and the DAI link to the WM1250-EV1 baseband module as
ignoring suspend.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Add stub baseband link on Speyside

Demonstrate the connection of a baseband to the system. We add a DAI for
the link to the baseband. This will become visible to the application
layer - audio should be started from the application layer using an
application such as this:

   http://opensource.wolfsonmicro.com/~gg/bluetooth-pcm/bluetooth_pcm.c

which starts up audio as for CPU based playback and record up to the point
where data is streamed.

Due to non-availability of baseband simulation hardware we reuse the
configuration for the CPU link with the CODEC acting as clock master,
allowing signals to be observed with a scope. A more standard system
would have separate configuration for the baseband with its own ops
structure and operations. Normally the baseband would be clock master
as the baseband audio will be synchronised to the external telephony
network.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Add pin switches for fixed analogue inputs and outputs on Speyside

Pin switches enable direct control of the DAPM state from userspace,
enabling simple enabling and disabling of the path. This is especially
useful for outputs such as the speaker which are composed of several
physical devices as it allows them to be controlled as a group.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Add Speyside headset jack detection support

Speyside makes use of support the WM8915 has for detecting the polarity
of the microphone and ground connections on headsets, using a GPIO to
control the polarity of the ground connection and switching between the
two microphone bias supplies available on the device in order to do so.
As a result of this the detection support is more involved than for most
other CODECs, using a callback to configure the current polarity of the
jack and translate this into the board-specific connections required for
the current scenario.

On Android some additional work is required to hook this up to the
application layer as the Android HeadsetObserver monitors a custom
drivers/switch API rather than the standard Linux APIs.  This can be
done by either updating HeadsetObserver or modifying the ALSA core to
report via drivers/switch as well.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Support the sub speaker driver on Speyside

Speyside includes a WM9081 configured as an external speaker driver taking
an analogue input from HPOUT2 on the WM8915 on the system. Add support for
this to the driver, using a prefix of "Sub" for the WM9081 controls to
ensure we avoid collisions with controls on the WM8915.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Optimise clock management for WM8915 Speyside

Dynamically enable and disable the FLL on the WM8915, configuring the
system clock to 256fs for 48kHz when the device is active but reverting
to using the input 32.768kHz clock directly at other times to support
features such as jack detection with minimal power consumption.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Add basic widgets for WM8915 Speyside

Provide widgets for the basic widgets connected directly to the WM8915
on Speyside - the headphones, speaker, digital and analogue microphones.
For the outputs this is just documentation, for the inputs this ensures
that the relevant microphone biases are enabled when they are in use.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Initial audio support for Speyside on Cragganmore 6410

This is minimal code required to get audio out of the Speyside audio
subsystem on the Wolfson Cragganmore 6410 reference platform.  It sets
up the link between the CPU and AIF1 of the WM8915 on the system,
enabling audio playback via the headphone and speaker outputs of the
device (which require no further configuration except runtime).  It
allows verification of basic functionality of the system.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Create card DAPM widgets early so they can be used in callbacks

This helps with things like setting up the initial state.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Move WM8915 FLL operations onto the CODEC

Since the WM8915 FLL is not tied to a particular audio interface move it
to a CODEC wide operation.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Fix mis cherry-pick of wm1250-ev1 driver

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Add initial WM1250-EV1 Springbank audio I/O module driver

The WM1250-EV1 Springbank audio I/O module for the Wolfson Glenfarclas
reference platform provides a simple audio I/O with an independant clock
domain, intended to simulate cellular modem and bluetooth subsystems
within the platform.

The card supports some limited GPIO based control but this is currently not
implemented.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Add WM8915 CODEC driver

The WM8915 is an ultra low power mobile CODEC designed for smartphones,
featuring a mixture of digital and analogue I/O with flexible mixing
options and advanced low power accessory detection functionality in a
compact package.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

ASoC: Add soc_remove_dai_links

card->num_rtd should be 0 after soc_romve_dai_link

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: SAMSUNG: Add WM8580 PCM Machine driver

This patch add WM8580 PCM machine driver to support PCM audio
on SMDKC110, SMDKV210, SMDK6450, SMDK6440 boards.
Playback and Capture supports 8kHz sampling rates.
and It is tested on SMDKC110, SMDKV210, SMDK6450

Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'for-2.6.39' into for-2.6.40

ASoC: Fix output PGA enabling in wm_hubs CODECs

The output PGA was not being powered up in headphone and speaker paths,
removing the ability to offer volume control and mute with the output
PGA.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org

ASoC: sn95031: decorate function with __devexit_p()

According to the comments in include/linux/init.h:

"Pointers to __devexit functions must use __devexit_p(function_name), the
wrapper will insert either the function_name or NULL, depending on the config
options."

Fix this issue in codecs sn95031.

Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: SAMSUNG: Fix the inverted clocks handling for pcm driver

Fix the inverted clocks handling for pcm cpu driver.
By using SND_SOC_DAIFMT_NB_NF, Audio noise can be generated on SMDK.

Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: sst_platform: Fix lock acquring

Fix the possible dead lock shown below:

spin_lock
sst_get_stream_status
sst_period_elapsed
intel_sst_interrupt
handle_IRQ_event
handle_fasteoi_irq
do_IRQ
common_interrupt
spin_lock
sst_set_stream_status
sst_platform_pcm_trigger

Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: fsi: driver safely remove for against irq

free_irq and pm_runtime_disable should be called before
snd_soc_unregister_xxx

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: fsi: modify vague PM control on probe

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: fsi: take care in failing case of dai register

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'for-2.6.39' into for-2.6.40

MAINTAINERS: Update Samsung ASoC maintainer's id

Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Allow DAPM pin operations to match any context

The DAPM pin operations currently require that the specific DAPM context
that the pin being operated in is contained in be specified. With multi
component and especially with the addition of a per-card DAPM context
this isn't ideal as it means that things like disabling unused pins on
CODECs require looking up the CODEC DAPM context.

Fix this by falling back to matching a widget in any context if there isn't
a match in the current context. The code isn't ideal currently but will do
the job.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Force all DAPM contexts into the same bias state

Currently we allow all DAPM contexts to determine their own bias level.
While this should in general work in most situations and will deliver the
lowest possible power it causes problems for our integration with the
card bias level as we're calling the card bias level functions for each
DAPM context even though they're card wide but don't say which CODEC
we're calling them for. Mitigate against this by forcing everything to
be in the same state.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Remove special casing for registerless widgets

Since we recently explicitly set the register for registerless widgets
to no register there is no longer any need to special case power updates
for them, we can allow them to be handled with the register compression
code as other widgets are.

As this is the only remaining user of dapm_generic_apply_power() and
dapm_update_bits() also remove those functions.

Noticed-by: Lu Guanqun <guanqun.lu@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

sst: fix compile error

Add several include files to fix the below compile error.

drivers/staging/intel_sst/intelmid.c: In function ‘snd_intelmad_sst_register’:
drivers/staging/intel_sst/intelmid.c:805:2: error: ‘sst_drv_ctx’ undeclared (first use in this function)
drivers/staging/intel_sst/intelmid.c:805:2: note: each undeclared identifier is reported only once for each function it appears in

Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'for-2.6.39' into for-2.6.40

ASoC: SSM2602: add SPI support

The ssm2602 codec has a SPI interface as well as I2C, so add the simple
bit of glue to make it usable.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Add data based control initialisation for CODECs and cards

Allow CODEC and card drivers to point to an array of controls from their
driver structure rather than explicitly calling snd_soc_add_controls().

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: WM8903: HP and Line out PGA/mixer DAPM fixes

Update the headphone and line out mixers and PGAs use the same logical
set of register bits and sequencing as the speaker mixer/PGA.

This allows ALSA controls for mute and volume on headphone and line out
to operate correctly.

Per conversation on alsa-devel, earlier datasheets indicated that the
POWER_MANAGEMENT_* register bits 0 and 1 were aliases to ANALOG_* register
bits 0 and 4, and hence only one copy of those bits was programmed.
However, later datasheets corrected this.

From: Dilan Lee <dilee@nvidia.com>
[swarren: Applied same change to headphone widgets]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'for-2.6.39' into for-2.6.40

ASoC: Set left channel volume update bits for WM8994

Ensures that we apply volume updates that don't affect the right channel.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: fix config error path

initialize ret to invalid value so that when we reach the config error path in
soc_pcm_open, it will return the correct error code. without this patch, though
config error path is executed, soc_pcm_open will return 0 in
snd_pcm_open_substream and then cause double release of substream.

Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: check channel mismatch between cpu_dai and codec_dai

Suppose we have:

cpu_dai
channels_min = 1
channels_max = 1

codec_dai
channels_min = 2
channels_max = 2

This is a mismatch that should not happen, however according to the current
code, the result of runtime->hw will be:

channels_min = 2
channels_max = 1

We better spot it early. This patch checks this mismatch.

Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: sst_platform: unregister sst card when being closed

Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

sst: make register_sst_card more self-contained

register_sst_card is used in ASoC code with field `scard_ops` being NULL.
Without this patch, there will be NULL dereference.

Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: sst_platform: free the resources on fail path

Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: sst_platform: initialize module_name properly

module_name will be checked in register_sst_card.
It will fail to register sst card if it's not initialized.

Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Add max98095 CODEC driver

This patch adds the MAX98095 CODEC driver.

Signed-off-by: Peter Hsiang <peter.hsiang@maxim-ic.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'for-2.6.39' into for-2.6.40

ASoC: Tegra: Suspend/resume support

ASoC machine drivers that are their own platform_driver (as opposed to
those using the soc-audio platform_driver) need to explicitly set up
power-management operation callbacks.

To avoid cut/paste, snd_soc_pm_ops also needs to be exported.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'for-2.6.40' of git://git./linux/kernel/git/broonie/sound-2.6 into topic/asoc

ASoC: Add bias level data to DAPM context debugfs

This is also in the old sysfs diagnostics but it's nice to have everything
in one place.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Fix comment width in soc-cache.c

Lines should be less than 80 columns.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Remove excessively verbose logging on I2C write

We don't need to log every I2C transfer, and certainly not at error level.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Fix to avoid compile error

This patch fixes to avoid compile error when ASoC codec doesn't use I2C
nor SPI on snd_soc_hw_bulk_write_raw().

Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'for-2.6.39' into for-2.6.40

ASoC: format_register_str: Don't clip register values

wordsize is used as the textual width of a register address.

regsize is used as the textual width of a register value.

The assignments to these values were swapped. In the case of WM8903, which
has 8-bit register addresses and 16-bit register values, this caused the
register values to be clipped to 2 digits instead of the full 4.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Properly handle spitz MIC GPIO

This patch firstly restructurizes the code a bit by getting rid of continuous
checking for machine type in spitz_mic_bias().

Then the patch properly requests the MIC GPIO in the spitz_init() and frees it
in spitz_exit().

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Name jack GPIOs based on jack not codec

snd_soc_jack_gpio has a name field. Use that name when registering the IRQ,
since this is far more informative than the codec driver name. This shows
up in /proc/interrupts.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'for-2.6.39' into for-2.6.40

Merge branch 'for-2.6.39' of git://git./linux/kernel/git/broonie/sound-2.6 into for-2.6.39

ASoC: PXA: Fix oops in __pxa2xx_pcm_prepare

pxa2xx_pcm_hw_free frees dma channel and sets prtd->dma_ch to -1,
but does not set prtd->params to NULL, so if pxa2xx_pcm_hw_params will
be called immediately, it leaves prtd->dma_ch initialized with -1,
and it results in oops in __pxa2xx_pcm_prepare. This bug is triggered
via SDL.

This patch adds check for prtd->dma_ch to __pxa2xx_pcm_prepare and
cleans prtd->params, so now it works properly.

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Use data based init for sn95031 DAPM

Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Use data based init for ak4535 DAPM

Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Use data based init for tlv320aic23 DAPM

Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Use data based init for wm8711 DAPM

Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Use data based init for wm8728 DAPM

Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Use data based init for wm9705 DAPM

Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Use data based init for wm9712 DAPM

Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Use data based init for wm9713 DAPM

Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Use data based init for max98088 DAPM

Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Use data based init for cx20442 DAPM

Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Use data based init for ak4671 DAPM

Signed-off-by: Lu Guanqun <guanqun.lu@intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: soc-cache: Warn on syncing any non-writable registers

When syncing the cache, if the driver has given us a writable_register()
callback, use it to check if we are syncing a non-writable register
and if so warn the user.

Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: soc-cache: Fix indentation issues

Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: zylonite: set .codec_dai_name in initializer

Fix the initialization of .codec_dai_name in zylonite_dai initializer,
do not mix it with the initialization of .codec_name which is set
already a few lines above.

Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Blackfin: push down SPORT settings from global variables

Now that we have multi-component support, take the time to unify the
SPORT implementations a bit and make the setup dynamic.  This kills
off the global sport_handle which was shared across all the Blackfin
machine drivers.  The pin management aspect is off loaded to platform
resources, and now multiple SPORTs can be instantiated simultaneously.

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Scott Jiang <scott.jiang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Blackfin: standardize machine driver names

Some machine drivers were using "bf5xx-", others were using "bf5xx_",
while others were using "bfin-".  Further, some were using the same
name in the transport layer which makes it hard to use different codecs
at the same time.  So standardize all of them to "bfin-" and make sure
they are name spaced according to their driver name.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Blackfin: drop "-codec" from codec names

The recent multi-component patch incorrectly added "-codec" suffixes to
parts which are not MFD.  Drop the suffix from the machine drivers too.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Blackfin: add ad193x sysclk configuration

Signed-off-by: Scott Jiang <scott.jiang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: SSM2602: convert to soc-cache

Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: ad1980: fix codec name

The codec name should not have a "-codec" suffix since this is not part of
a MFD.  This was incorrectly changed during the multi-component updated.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: ad193x: fix codec name

The codec name should not have a "-codec" suffix since this is not part of
a MFD.  This was incorrectly changed during the multi-component updated.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: ad73311: fix codec name

The codec name should not have a "-codec" suffix since this is not part of
a MFD.  This was incorrectly changed during the multi-component updated.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: SSM2602: fix codec name

The codec name should not have a "-codec" suffix since this is not part of
a MFD.  This was incorrectly changed during the multi-component updated.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: fix sorting order of codecs in kconfig

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

ASoC: Remove -codec from WM8731 driver name

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Convert WM8731 to table based DAPM setup

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

ASoC: Convert WM8903 to table based DAPM setup

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>

Merge branch 'for-2.6.39' into for-2.6.40

ASoC: Fix CODEC device name for Corgi

Got typoed in the multi-component changes.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@kernel.org

Linux 2.6.39-rc1

Merge branch 'for-linus' of git://git./linux/kernel/git/cjb/mmc

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (26 commits)
  mmc: SDHI should depend on SUPERH || ARCH_SHMOBILE
  mmc: tmio_mmc: Move some defines into a shared header
  mmc: tmio: support aggressive clock gating
  mmc: tmio: fix power-mode interpretation
  mmc: tmio: remove work-around for unmasked SDIO interrupts
  sh: fix SDHI IO address-range
  ARM: mach-shmobile: fix SDHI IO address-range
  mmc: tmio: only access registers above 0xff, if available
  mfd: remove now redundant sh_mobile_sdhi.h header
  sh: convert boards to use linux/mmc/sh_mobile_sdhi.h
  ARM: mach-shmobile: convert boards to use linux/mmc/sh_mobile_sdhi.h
  mmc: tmio: convert the SDHI MMC driver from MFD to a platform driver
  sh: ecovec: use the CONFIG_MMC_TMIO symbols instead of MFD
  mmc: tmio: split core functionality, DMA and MFD glue
  mmc: tmio: use PIO for short transfers
  mmc: tmio-mmc: Improve DMA stability on sh-mobile
  mmc: fix mmc_app_send_scr() for dma transfer
  mmc: sdhci-esdhc: enable esdhc on imx53
  mmc: sdhci-esdhc: use writel/readl as general APIs
  mmc: sdhci: add the abort CMDTYPE bits definition
  ...

Merge branch 'frv' of git://git./linux/kernel/git/dhowells/linux-2.6-frv

* 'frv' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-frv:
  FRV: Use generic show_interrupts()
  FRV: Convert genirq namespace
  frv: Select GENERIC_HARDIRQS_NO_DEPRECATED
  frv: Convert cpu irq_chip to new functions
  frv: Convert mb93493 irq_chip to new functions
  frv: Convert mb93093 irq_chip to new function
  frv: Convert mb93091 irq_chip to new functions
  frv: Fix typo from __do_IRQ overhaul
  frv: Remove stale irq_chip.end
  FRV: Do some cleanups
  FRV: Missing node arg in alloc_thread_info_node() macro
  NOMMU: implement access_remote_vm
  NOMMU: support SMP dynamic percpu_alloc
  NOMMU: percpu should use is_vmalloc_addr().

Merge branch 'stable/bug-fixes-rc1' of git://git./linux/kernel/git/konrad/xen

* 'stable/bug-fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen: Use new irq_move functions
  xen: Convert genirq namespace
  xen: fix p2m section mismatches
  xen/p2m: Allocate p2m tracking pages on override
  xen-gntdev: unlock on error path in gntdev_mmap()
  xen-gntdev: return -EFAULT on copy_to_user failure

Merge git://git./linux/kernel/git/wim/linux-2.6-watchdog

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  watchdog: softdog.c: enhancement to optionally invoke panic instead of reboot on timer expiry
  watchdog: fix nv_tco section mismatch
  watchdog: sp5100_tco.c: Check if firmware has set correct value in tcobase.
  watchdog: Convert release_resource to release_region/release_mem_region
  watchdog: s3c2410_wdt.c: Convert release_resource to release_region/release_mem_region

Merge branch 'for-linus' of git://git./linux/kernel/git/bp/bp

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
  amd64_edac: Fix potential memleak

Merge branch 'irq-final-for-linus-v2' of git://git./linux/kernel/git/tip/linux-2.6-tip

* 'irq-final-for-linus-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (111 commits)
  gpio: ab8500: Mark broken
  genirq: Remove move_*irq leftovers
  genirq: Remove compat code
  drivers: Final irq namespace conversion
  mn10300: Use generic show_interrupts()
  mn10300: Cleanup irq_desc access
  mn10300: Convert genirq namespace
  frv: Use generic show_interrupts()
  frv: Convert genirq namespace
  frv: Select GENERIC_HARDIRQS_NO_DEPRECATED
  frv: Convert cpu irq_chip to new functions
  frv: Convert mb93493 irq_chip to new functions
  frv: Convert mb93093 irq_chip to new function
  frv: Convert mb93091 irq_chip to new functions
  frv: Fix typo from __do_IRQ overhaul
  frv: Remove stale irq_chip.end
  m68k: Convert irq function namespace
  xen: Use new irq_move functions
  xen: Cleanup genirq namespace
  unicore32: Use generic show_interrupts()
  ...

char/tpm: Fix unitialized usage of data buffer

This patch fixes information leakage to the userspace by initializing
the data buffer to zero.

Reported-by: Peter Huewe <huewe.external@infineon.com>
Signed-off-by: Peter Huewe <huewe.external@infineon.com>
Signed-off-by: Marcel Selhorst <m.selhorst@sirrix.com>
[ Also removed the silly "* sizeof(u8)".  If that isn't 1, we have way
  deeper problems than a simple multiplication can fix.   - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

amd64_edac: Fix potential memleak

We check the pointers together but at least one of them could be invalid
due to failed allocation. Since we cannot continue if either of the two
allocations has failed, exit early by freeing them both.

Cc: <stable@kernel.org> # 38.x
Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>

fs: don't use igrab() while holding i_lock

Fix the incorrect use of igrab() inside the i_lock in NFS and Ceph‥

If we are already holding the i_lock, we have a reference to the
inode so we can safely use ihold() to gain an extra reference. This
avoids hangs due to lock recursion on the i_lock now that the
inode_lock is gone and igrab() uses the i_lock itself.

Signed-off-by: Dave Chinner <dchinner@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Cc: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge git://git./linux/kernel/git/davem/net-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (30 commits)
  xfrm: Restrict extended sequence numbers to esp
  xfrm: Check for esn buffer len in xfrm_new_ae
  xfrm: Assign esn pointers when cloning a state
  xfrm: Move the test on replay window size into the replay check functions
  netdev: bfin_mac: document TE setting in RMII modes
  drivers net: Fix declaration ordering in inline functions.
  cxgb3: Apply interrupt coalescing settings to all queues
  net: Always allocate at least 16 skb frags regardless of page size
  ipv4: Don't ip_rt_put() an error pointer in RAW sockets.
  net: fix ethtool->set_flags not intended -EINVAL return value
  mlx4_en: Fix loss of promiscuity
  tg3: Fix inline keyword usage
  tg3: use <linux/io.h> and <linux/uaccess.h> instead <asm/io.h> and <asm/uaccess.h>
  net: use CHECKSUM_NONE instead of magic number
  Net / jme: Do not use legacy PCI power management
  myri10ge: small rx_done refactoring
  bridge: notify applications if address of bridge device changes
  ipv4: Fix IP timestamp option (IPOPT_TS_PRESPEC) handling in ip_options_echo()
  can: c_can: Fix tx_bytes accounting
  can: c_can_platform: fix irq check in probe
  ...

xen: Use new irq_move functions

These functions take irq_data as an argument and avoid a redundant
lookup in the sparse irq case.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>

xen: Convert genirq namespace

Converted with coccinelle.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>

xen: fix p2m section mismatches

Fix section mismatch warnings:
set_phys_range_identity() is called by __init xen_set_identity(),
so also mark set_phys_range_identity() as __init.
then:
__early_alloc_p2m() is called set_phys_range_identity(), so also mark
__early_alloc_p2m() as __init.

WARNING: arch/x86/built-in.o(.text+0x7856): Section mismatch in reference from the function __early_alloc_p2m() to the function .init.text:extend_brk()
The function __early_alloc_p2m() references
the function __init extend_brk().
This is often because __early_alloc_p2m lacks a __init
annotation or the annotation of extend_brk is wrong.

WARNING: arch/x86/built-in.o(.text+0x7967): Section mismatch in reference from the function set_phys_range_identity() to the function .init.text:extend_brk()
The function set_phys_range_identity() references
the function __init extend_brk().
This is often because set_phys_range_identity lacks a __init
annotation or the annotation of extend_brk is wrong.

[v2: Per Stephen Hemming recommonedation made __early_alloc_p2m static]
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>

FRV: Use generic show_interrupts()

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Howells <dhowells@redhat.com>