Jarkko Sakkinen [Tue, 4 Oct 2016 06:49:47 +0000 (09:49 +0300)]
tpm: remove invalid min length check from tpm_do_selftest()
Removal of this check was not properly amended to the original commit.
Cc: stable@vger.kernel.org
Fixes: 0c541332231e ("tpm: use tpm_pcr_read_dev() in tpm_do_selftest()")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Linus Torvalds [Sun, 30 Oct 2016 03:33:20 +0000 (20:33 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
"Lots of fixes, mostly drivers as is usually the case.
1) Don't treat zero DMA address as invalid in vmxnet3, from Alexey
Khoroshilov.
2) Fix element timeouts in netfilter's nft_dynset, from Anders K.
Pedersen.
3) Don't put aead_req crypto struct on the stack in mac80211, from
Ard Biesheuvel.
4) Several uninitialized variable warning fixes from Arnd Bergmann.
5) Fix memory leak in cxgb4, from Colin Ian King.
6) Fix bpf handling of VLAN header push/pop, from Daniel Borkmann.
7) Several VRF semantic fixes from David Ahern.
8) Set skb->protocol properly in ip6_tnl_xmit(), from Eli Cooper.
9) Socket needs to be locked in udp_disconnect(), from Eric Dumazet.
10) Div-by-zero on 32-bit fix in mlx4 driver, from Eugenia Emantayev.
11) Fix stale link state during failover in NCSCI driver, from Gavin
Shan.
12) Fix netdev lower adjacency list traversal, from Ido Schimmel.
13) Propvide proper handle when emitting notifications of filter
deletes, from Jamal Hadi Salim.
14) Memory leaks and big-endian issues in rtl8xxxu, from Jes Sorensen.
15) Fix DESYNC_FACTOR handling in ipv6, from Jiri Bohac.
16) Several routing offload fixes in mlxsw driver, from Jiri Pirko.
17) Fix broadcast sync problem in TIPC, from Jon Paul Maloy.
18) Validate chunk len before using it in SCTP, from Marcelo Ricardo
Leitner.
19) Revert a netns locking change that causes regressions, from Paul
Moore.
20) Add recursion limit to GRO handling, from Sabrina Dubroca.
21) GFP_KERNEL in irq context fix in ibmvnic, from Thomas Falcon.
22) Avoid accessing stale vxlan/geneve socket in data path, from
Pravin Shelar"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (189 commits)
geneve: avoid using stale geneve socket.
vxlan: avoid using stale vxlan socket.
qede: Fix out-of-bound fastpath memory access
net: phy: dp83848: add dp83822 PHY support
enic: fix rq disable
tipc: fix broadcast link synchronization problem
ibmvnic: Fix missing brackets in init_sub_crq_irqs
ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context
Revert "ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context"
arch/powerpc: Update parameters for csum_tcpudp_magic & csum_tcpudp_nofold
net/mlx4_en: Save slave ethtool stats command
net/mlx4_en: Fix potential deadlock in port statistics flow
net/mlx4: Fix firmware command timeout during interrupt test
net/mlx4_core: Do not access comm channel if it has not yet been initialized
net/mlx4_en: Fix panic during reboot
net/mlx4_en: Process all completions in RX rings after port goes up
net/mlx4_en: Resolve dividing by zero in 32-bit system
net/mlx4_core: Change the default value of enable_qos
net/mlx4_core: Avoid setting ports to auto when only one port type is supported
net/mlx4_core: Fix the resource-type enum in res tracker to conform to FW spec
...
pravin shelar [Fri, 28 Oct 2016 16:59:16 +0000 (09:59 -0700)]
geneve: avoid using stale geneve socket.
This patch is similar to earlier vxlan patch.
Geneve device close operation frees geneve socket. This
operation can race with geneve-xmit function which
dereferences geneve socket. Following patch uses RCU
mechanism to avoid this situation.
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pravin shelar [Fri, 28 Oct 2016 16:59:15 +0000 (09:59 -0700)]
vxlan: avoid using stale vxlan socket.
When vxlan device is closed vxlan socket is freed. This
operation can race with vxlan-xmit function which
dereferences vxlan socket. Following patch uses RCU
mechanism to avoid this situation.
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mintz, Yuval [Sat, 29 Oct 2016 14:04:35 +0000 (17:04 +0300)]
qede: Fix out-of-bound fastpath memory access
Driver allocates a shadow array for transmitted SKBs with X entries;
That means valid indices are {0,...,X - 1}. [X == 8191]
Problem is the driver also uses X as a mask for a
producer/consumer in order to choose the right entry in the
array which allows access to entry X which is out of bounds.
To fix this, simply allocate X + 1 entries in the shadow array.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roger Quadros [Fri, 28 Oct 2016 09:40:20 +0000 (12:40 +0300)]
net: phy: dp83848: add dp83822 PHY support
This PHY has a compatible register set with DP83848x so
add support for it.
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Govindarajulu Varadarajan [Thu, 27 Oct 2016 23:01:03 +0000 (16:01 -0700)]
enic: fix rq disable
When MTU is changed from 9000 to 1500 while there is burst of inbound 9000
bytes packets, adaptor sometimes delivers 9000 bytes packets to 1500 bytes
buffers. This causes memory corruption and sometimes crash.
This is because of a race condition in adaptor between "RQ disable"
clearing descriptor mini-cache and mini-cache valid bit being set by
completion of descriptor fetch. This can result in stale RQ desc being
cached and used when packets arrive. In this case, the stale descriptor
have old MTU value.
Solution is to write RQ->disable twice. The first write will stop any
further desc fetches, allowing the second disable to clear the mini-cache
valid bit without danger of a race.
Also, the check for rq->running becoming 0 after writing rq->enable to 0
is not done properly. When incoming packets are flooding the interface,
rq->running will pulse high for each dropped packet. Since the driver was
waiting for 10us between each poll, it is possible to see rq->running = 1
1000 times in a row, even though it is not actually stuck running.
This results in false failure of vnic_rq_disable(). Fix is to try more
than 1000 time without delay between polls to ensure we do not miss when
running goes low.
In old adaptors rq->enable needs to be re-written to 0 when posted_index
is reset in vnic_rq_clean() in order to keep rq->prefetch_index in sync.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Thu, 27 Oct 2016 22:51:55 +0000 (18:51 -0400)]
tipc: fix broadcast link synchronization problem
In commit
2d18ac4ba745 ("tipc: extend broadcast link initialization
criteria") we tried to fix a problem with the initial synchronization
of broadcast link acknowledge values. Unfortunately that solution is
not sufficient to solve the issue.
We have seen it happen that LINK_PROTOCOL/STATE packets with a valid
non-zero unicast acknowledge number may bypass BCAST_PROTOCOL
initialization, NAME_DISTRIBUTOR and other STATE packets with invalid
broadcast acknowledge numbers, leading to premature opening of the
broadcast link. When the bypassed packets finally arrive, they are
inadvertently accepted, and the already correctly initialized
acknowledge number in the broadcast receive link is overwritten by
the invalid (zero) value of the said packets. After this the broadcast
link goes stale.
We now fix this by marking the packets where we know the acknowledge
value is or may be invalid, and then ignoring the acks from those.
To this purpose, we claim an unused bit in the header to indicate that
the value is invalid. We set the bit to 1 in the initial BCAST_PROTOCOL
synchronization packet and all initial ("bulk") NAME_DISTRIBUTOR
packets, plus those LINK_PROTOCOL packets sent out before the broadcast
links are fully synchronized.
This minor protocol update is fully backwards compatible.
Reported-by: John Thompson <thompa.atl@gmail.com>
Tested-by: John Thompson <thompa.atl@gmail.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon [Thu, 27 Oct 2016 17:28:52 +0000 (12:28 -0500)]
ibmvnic: Fix missing brackets in init_sub_crq_irqs
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon [Thu, 27 Oct 2016 17:28:51 +0000 (12:28 -0500)]
ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context
Schedule these XPORT event tasks in the shared workqueue
so that IRQs are not freed in an interrupt context when
sub-CRQs are released.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 29 Oct 2016 21:18:17 +0000 (17:18 -0400)]
Revert "ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context"
This reverts commit
8d7533e5aaad1c94386a8101a36b0617987966b7.
It introduced kbuild failures, new version coming.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 29 Oct 2016 21:14:19 +0000 (17:14 -0400)]
Merge branch '40GbE' of git://git./linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2016-10-27
This series contains fixes to ixgbe and i40e.
Emil fixes a NULL pointer dereference when a macvlan interface is brought
up while the PF is still down.
David root caused the original panic that was fixed by commit id
(
a036244c068612 "i40e: Fix kernel panic on enable/disable LLDP") and the
fix was not quite correct, so removed the get_default_tc() and replaced
it with a #define since there is only one TC supported as a default.
Guilherme Piccoli fixes an issue where if we modprobe the driver module
without enough MSI-X interrupts, then unload the module and reload it
again, the kernel would crash. So if we fail to allocate enough MSI-X
interrupts, we should disable them since they were previously enabled.
Huaibin Wang found that the order of the arguments for
ndo_dflt_bridge_getlink() were in the correct order, so fix the order.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera [Thu, 27 Oct 2016 14:30:06 +0000 (16:30 +0200)]
arch/powerpc: Update parameters for csum_tcpudp_magic & csum_tcpudp_nofold
Commit
01cfbad "ipv4: Update parameters for csum_tcpudp_magic to their
original types" changed parameters for csum_tcpudp_magic and
csum_tcpudp_nofold for many platforms but not for PowerPC.
Fixes: 01cfbad "ipv4: Update parameters for csum_tcpudp_magic to their original types"
Cc: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 29 Oct 2016 20:52:02 +0000 (13:52 -0700)]
Linux 4.9-rc3
Linus Torvalds [Sat, 29 Oct 2016 20:42:44 +0000 (13:42 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 bugfix from Thomas Gleixner:
"A single bugfix for the recent changes related to registering the boot
cpu when this has not happened before prefill_possible_map().
The main problem with this change got fixed already, but we missed the
case where the local APIC is not yet mapped, when prefill_possible_map()
is invoked, so the registration of the boot cpu which has the APIC bit
set in CPUID will explode.
I should have seen that issue earlier, but all I can do now is feeling
embarassed"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/smpboot: Init apic mapping before usage
David S. Miller [Sat, 29 Oct 2016 20:23:49 +0000 (16:23 -0400)]
Merge branch 'mlx4-fixes'
Tariq Toukan says:
====================
mlx4 misc fixes for 4.9
This patchset contains several bug fixes from the team to the
mlx4 Eth and Core drivers.
Series generated against net commit:
ecc515d7238f 'sctp: fix the panic caused by route update'
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Thu, 27 Oct 2016 13:27:22 +0000 (16:27 +0300)]
net/mlx4_en: Save slave ethtool stats command
Following the previous patch, as an optimization, the slave will
not even bother sending the DUMP_ETH_STATS command over the
comm channel.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Thu, 27 Oct 2016 13:27:21 +0000 (16:27 +0300)]
net/mlx4_en: Fix potential deadlock in port statistics flow
mlx4_en_DUMP_ETH_STATS took the *counter mutex* and then
called the FW command, with WRAPPED attribute. As a result, the fw command
is wrapped on the Hypervisor when it calls mlx4_en_DUMP_ETH_STATS.
The FW command wrapper flow on the hypervisor takes the *slave_cmd_mutex*
during processing.
At the same time, a VF could be in the process of coming up, and could
call mlx4_QUERY_FUNC_CAP. On the hypervisor, the command flow takes the
*slave_cmd_mutex*, then executes mlx4_QUERY_FUNC_CAP_wrapper.
mlx4_QUERY_FUNC_CAP wrapper calls mlx4_get_default_counter_index(),
which takes the *counter mutex*. DEADLOCK.
The fix is that the DUMP_ETH_STATS fw command should be called with
the NATIVE attribute, so that on the hypervisor, this command does not
enter the wrapper flow.
Since the Hypervisor no longer goes through the wrapper code, we also
simply return 0 in mlx4_DUMP_ETH_STATS_wrapper (i.e.the function succeeds,
but the returned data will be all zeroes).
No need to test if it is the Hypervisor going through the wrapper.
Fixes: f9baff509f8a ("mlx4_core: Add "native" argument to mlx4_cmd ...")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eugenia Emantayev [Thu, 27 Oct 2016 13:27:20 +0000 (16:27 +0300)]
net/mlx4: Fix firmware command timeout during interrupt test
Currently interrupt test that is part of ethtool selftest runs the
check over all interrupt vectors of the device.
In mlx4_en package part of interrupt vectors are uninitialized since
mlx4_ib doesn't exist. This causes NOP FW command to time out.
Change logic to test current port interrupt vectors only.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Thu, 27 Oct 2016 13:27:19 +0000 (16:27 +0300)]
net/mlx4_core: Do not access comm channel if it has not yet been initialized
In the Hypervisor, there are several FW commands which are invoked
before the comm channel is initialized (in mlx4_multi_func_init).
These include MOD_STAT_CONFIG, QUERY_DEV_CAP, INIT_HCA, and others.
If any of these commands fails, say with a timeout, the Hypervisor
driver enters the internal error reset flow. In this flow, the driver
attempts to notify all slaves via the comm channel that an internal error
has occurred.
Since the comm channel has not yet been initialized (i.e., mapped via
ioremap), this will cause dereferencing a NULL pointer.
To fix this, do not access the comm channel in the internal error flow
if it has not yet been initialized.
Fixes: 55ad359225b2 ("net/mlx4_core: Enable device recovery flow with SRIOV")
Fixes: ab9c17a009ee ("mlx4_core: Modify driver initialization flow to accommodate SRIOV for Ethernet")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eugenia Emantayev [Thu, 27 Oct 2016 13:27:18 +0000 (16:27 +0300)]
net/mlx4_en: Fix panic during reboot
Fix a kernel panic that occurs as a result of an asynchronous event
handled in roce_gid_mgmt:
mlx4_en_get_drvinfo is called and accesses freed resources.
This happens in a shutdown flow only, since pci device is destroyed
while netdevice is still alive.
Fixes: c27a02cd94d6 ("mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC")
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Erez Shitrit [Thu, 27 Oct 2016 13:27:17 +0000 (16:27 +0300)]
net/mlx4_en: Process all completions in RX rings after port goes up
Currently there is a race between incoming traffic and
initialization flow. HW is able to receive the packets
after INIT_PORT is done and unicast steering is configured.
Before we set priv->port_up NAPI is not scheduled and
receive queues become full. Therefore we never get
new interrupts about the completions.
This issue could happen if running heavy traffic during
bringing port up.
The resolution is to schedule NAPI once port_up is set.
If receive queues were full this will process all cqes
and release them.
Fixes: c27a02cd94d6 ("mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC")
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eugenia Emantayev [Thu, 27 Oct 2016 13:27:16 +0000 (16:27 +0300)]
net/mlx4_en: Resolve dividing by zero in 32-bit system
When doing roundup_pow_of_two for large enough number with
bit 31, an overflow will occur and a value equal to 1 will
be returned. In this case 1 will be subtracted from the return
value and division by zero will be reached.
Fixes: 31c128b66e5b ("net/mlx4_en: Choose time-stamping shift value according to HW frequency")
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moshe Lazer [Thu, 27 Oct 2016 13:27:15 +0000 (16:27 +0300)]
net/mlx4_core: Change the default value of enable_qos
Change the default status of quality of service back to disabled,
as it hurts performance in some cases.
Fixes: 38438f7c7e8c ("net/mlx4: Set enhanced QoS support by default when ...")
Signed-off-by: Moshe Lazer <moshel@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maor Gottlieb [Thu, 27 Oct 2016 13:27:14 +0000 (16:27 +0300)]
net/mlx4_core: Avoid setting ports to auto when only one port type is supported
When only one port type is supported, it should be read only.
We reject changing requests, even to the auto sense mode.
Fixes: 27bf91d6a0d5 ("mlx4_core: Add link type autosensing")
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Thu, 27 Oct 2016 13:27:13 +0000 (16:27 +0300)]
net/mlx4_core: Fix the resource-type enum in res tracker to conform to FW spec
The resource type enum in the resource tracker was incorrect.
RES_EQ was put in the position of RES_NPORT_ID (a FC resource).
Since the remaining resources maintain their current values,
and RES_EQ is not passed from slaves to the hypervisor in any
FW command, this change affects only the hypervisor.
Therefore, there is no backwards-compatibility issue.
Fixes: 623ed84b1f95 ("mlx4_core: initial header-file changes for SRIOV support")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 29 Oct 2016 20:15:24 +0000 (13:15 -0700)]
Merge tag 'upstream-4.9-rc3' of git://git.infradead.org/linux-ubifs
Pull ubi/ubifs fixes from Richard Weinberger:
"This contains fixes for issues in both UBI and UBIFS:
- A regression wrt overlayfs, introduced in -rc2.
- An UBI issue, found by Dan Carpenter's static checker"
* tag 'upstream-4.9-rc3' of git://git.infradead.org/linux-ubifs:
ubifs: Fix regression in ubifs_readdir()
ubi: fastmap: Fix add_vol() return value test in ubi_attach_fastmap()
shamir rabinovitch [Thu, 27 Oct 2016 09:46:38 +0000 (05:46 -0400)]
rds: debug messages are enabled by default
rds use Kconfig option called "RDS_DEBUG" to enable rds debug messages.
This option cause the rds Makefile to add -DDEBUG to the rds gcc command
line.
When CONFIG_DYNAMIC_DEBUG is enabled, the "DEBUG" macro is used by
include/linux/dynamic_debug.h to decide if dynamic debug prints should
be sent by default to the kernel log.
rds should not enable this macro for production builds. rds dynamic
debug work as expected follow this fix.
Signed-off-by: Shamir Rabinovitch <shamir.rabinovitch@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Reviewed-by: Wengang Wang <wen.gang.wang@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 29 Oct 2016 19:54:16 +0000 (15:54 -0400)]
Merge tag 'mac80211-for-davem-2016-10-27' of git://git./linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just two fixes:
* a fix to process all events while suspending, so any
potential calls into the driver are done before it is
suspended
* small markup fixes for the sphinx documentation conversion
that's coming into the tree via the doc tree
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon [Wed, 26 Oct 2016 18:57:38 +0000 (13:57 -0500)]
ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context
Schedule these XPORT event tasks in the shared workqueue
so that IRQs are not freed in an interrupt context when
sub-CRQs are released.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Gunthorpe [Wed, 26 Oct 2016 17:47:02 +0000 (11:47 -0600)]
net: mv643xx_eth: Fetch the phy connection type from DT
The MAC is capable of RGMII mode and that is probably a more typical
connection type than GMII today (eg it is used by Marvell Reference
designs for several SOCs). Let DT users specify the standard
phy-connection-type = "rgmii-id";
On a phy node.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 29 Oct 2016 19:07:29 +0000 (12:07 -0700)]
Merge tag 'armsoc-fixes' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We haven't seen a whole lot of fixes for the first two weeks since the
merge window, but here is the batch that we have at the moment.
Nothing sticks out as particularly bad or scary, it's mostly a handful
of smaller fixes to several platforms. The Uniphier reset controller
changes could probably have been delayed to 4.10, but they're not
scary and just plumbing up driver changes that went in during the
merge window.
We're also adding another maintainer to Marvell Berlin platforms, to
help out when Sebastian is too busy. Yay teamwork!"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx: mach-imx6q: Fix the PHY ID mask for AR8031
ARM: dts: vf610: fix IRQ flag of global timer
ARM: imx: gpc: Fix the imx_gpc_genpd_init() error path
ARM: imx: gpc: Initialize all power domains
arm64: dts: Updated NAND DT properties for NS2 SVK
arm64: dts: uniphier: change MIO node to SD control node
ARM: dts: uniphier: change MIO node to SD control node
reset: uniphier: rename MIO reset to SD reset for Pro5, PXs2, LD20 SoCs
arm64: uniphier: select ARCH_HAS_RESET_CONTROLLER
ARM: uniphier: select ARCH_HAS_RESET_CONTROLLER
arm64: dts: Add timer erratum property for LS2080A and LS1043A
arm64: dts: rockchip: remove the abuse of keep-power-in-suspend
ARM: multi_v7_defconfig: Enable Intel e1000e driver
MAINTAINERS: add myself as Marvell berlin SoC maintainer
bus: qcom-ebi2: depend on ARCH_QCOM or COMPILE_TEST
ARM: dts: fix the SD card on the Snowball
arm64: dts: rockchip: remove always-on and boot-on from vcc_sd
arm64: dts: marvell: fix clocksource for CP110 master SPI0
ARM: mvebu: Select corediv clk for all mvebu v7 SoC
David S. Miller [Sat, 29 Oct 2016 19:05:53 +0000 (15:05 -0400)]
Merge tag 'batadv-net-for-davem-
20161026' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are three batman-adv bugfix patches:
- Fix RCU usage for neighbor list, by Sven Eckelmann
- Fix BATADV_DBG_ALL loglevel to include TP Meter messages, by Sven Eckelmann
- Fix possible splat when disabling an interface, by Linus Luessing
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Wed, 26 Oct 2016 15:30:29 +0000 (08:30 -0700)]
Revert "hv_netvsc: report vmbus name in ethtool"
This reverts commit
e3f74b841d48
("hv_netvsc: report vmbus name in ethtool")'
because of problem introduced by commit
f9a56e5d6a0ba
("Drivers: hv: make VMBus bus ids persistent").
This changed the format of the vmbus name and this new format is too
long to fit in the bus_info field of ethtool.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Wed, 26 Oct 2016 15:23:07 +0000 (11:23 -0400)]
packet: on direct_xmit, limit tso and csum to supported devices
When transmitting on a packet socket with PACKET_VNET_HDR and
PACKET_QDISC_BYPASS, validate device support for features requested
in vnet_hdr.
Drop TSO packets sent to devices that do not support TSO or have the
feature disabled. Note that the latter currently do process those
packets correctly, regardless of not advertising the feature.
Because of SKB_GSO_DODGY, it is not sufficient to test device features
with netif_needs_gso. Full validate_xmit_skb is needed.
Switch to software checksum for non-TSO packets that request checksum
offload if that device feature is unsupported or disabled. Note that
similar to the TSO case, device drivers may perform checksum offload
correctly even when not advertising it.
When switching to software checksum, packets hit skb_checksum_help,
which has two BUG_ON checksum not in linear segment. Packet sockets
always allocate at least up to csum_start + csum_off + 2 as linear.
Tested by running github.com/wdebruij/kerneltools/psock_txring_vnet.c
ethtool -K eth0 tso off tx on
psock_txring_vnet -d $dst -s $src -i eth0 -l 2000 -n 1 -q -v
psock_txring_vnet -d $dst -s $src -i eth0 -l 2000 -n 1 -q -v -N
ethtool -K eth0 tx off
psock_txring_vnet -d $dst -s $src -i eth0 -l 1000 -n 1 -q -v -G
psock_txring_vnet -d $dst -s $src -i eth0 -l 1000 -n 1 -q -v -G -N
v2:
- add EXPORT_SYMBOL_GPL(validate_xmit_skb_list)
Fixes: d346a3fae3ff ("packet: introduce PACKET_QDISC_BYPASS socket option")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Wed, 26 Oct 2016 12:44:33 +0000 (14:44 +0200)]
net_sched actions: use nla_parse_nested()
Use nla_parse_nested instead of open-coding the call to
nla_parse() with the attribute data/len.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar [Wed, 26 Oct 2016 07:56:38 +0000 (13:26 +0530)]
cxgb4: Fix error handling in alloc_uld_rxqs().
Fix to release resources properly in error handling path of
alloc_uld_rxqs(), This patch also removes unwanted arguments
and avoids calling the same function twice.
Fixes: 94cdb8bb993a (cxgb4: Add support for dynamic allocation
of resources for ULD
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Tue, 25 Oct 2016 16:16:20 +0000 (18:16 +0200)]
IB/mlx4: avoid a -Wmaybe-uninitialize warning
There is an old warning about mlx4_SW2HW_EQ_wrapper on x86:
ethernet/mellanox/mlx4/resource_tracker.c: In function ‘mlx4_SW2HW_EQ_wrapper’:
ethernet/mellanox/mlx4/resource_tracker.c:3071:10: error: ‘eq’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
The problem here is that gcc won't track the state of the variable
across a spin_unlock. Moving the assignment out of the lock is
safe here and avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eli Cooper [Wed, 26 Oct 2016 02:11:09 +0000 (10:11 +0800)]
ip6_tunnel: Update skb->protocol to ETH_P_IPV6 in ip6_tnl_xmit()
This patch updates skb->protocol to ETH_P_IPV6 in ip6_tnl_xmit() when an
IPv6 header is installed to a socket buffer.
This is not a cosmetic change. Without updating this value, GSO packets
transmitted through an ipip6 tunnel have the protocol of ETH_P_IP and
skb_mac_gso_segment() will attempt to call gso_segment() for IPv4,
which results in the packets being dropped.
Fixes: b8921ca83eed ("ip4ip6: Support for GSO/GRO")
Signed-off-by: Eli Cooper <elicooper@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Tue, 25 Oct 2016 22:37:53 +0000 (00:37 +0200)]
bpf: fix samples to add fake KBUILD_MODNAME
Some of the sample files are causing issues when they are loaded with tc
and cls_bpf, meaning tc bails out while trying to parse the resulting ELF
file as program/map/etc sections are not present, which can be easily
spotted with readelf(1).
Currently, BPF samples are including some of the kernel headers and mid
term we should change them to refrain from this, really. When dynamic
debugging is enabled, we bail out due to undeclared KBUILD_MODNAME, which
is easily overlooked in the build as clang spills this along with other
noisy warnings from various header includes, and llc still generates an
ELF file with mentioned characteristics. For just playing around with BPF
examples, this can be a bit of a hurdle to take.
Just add a fake KBUILD_MODNAME as a band-aid to fix the issue, same is
done in xdp*_kern samples already.
Fixes: 65d472fb007d ("samples/bpf: add 'pointer to packet' tests")
Fixes: 6afb1e28b859 ("samples/bpf: Add tunnel set/get tests.")
Fixes: a3f74617340b ("cgroup: bpf: Add an example to do cgroup checking in BPF")
Reported-by: Chandrasekar Kannan <ckannan@console.to>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 29 Oct 2016 18:19:02 +0000 (11:19 -0700)]
Merge tag 'char-misc-4.9-rc3' of git://git./linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a few small char/misc driver fixes for reported issues.
The "biggest" are two binder fixes for reported issues that have been
shipping in Android phones for a while now, the others are various
fixes for reported problems.
And there's a MAINTAINERS update for good measure.
All have been in linux-next with no reported issues"
* tag 'char-misc-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
MAINTAINERS: Add entry for genwqe driver
VMCI: Doorbell create and destroy fixes
GenWQE: Fix bad page access during abort of resource allocation
vme: vme_get_size potentially returning incorrect value on failure
extcon: qcom-spmi-misc: Sync the extcon state on interrupt
hv: do not lose pending heartbeat vmbus packets
mei: txe: don't clean an unprocessed interrupt cause.
ANDROID: binder: Clear binder and cookie when setting handle in flat binder struct
ANDROID: binder: Add strong ref checks
Olof Johansson [Sat, 29 Oct 2016 18:09:37 +0000 (11:09 -0700)]
Merge tag 'v4.9-rockchip-dts64-fixes1' of git://git./linux/kernel/git/mmind/linux-rockchip into fixes
Correct regulator handling on Rockchip arm64 boards to make
bind/unbind calls work correctly and remove a sdio-only
property from non-sdio mmc hosts, that accidentially was
added there.
* tag 'v4.9-rockchip-dts64-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: remove the abuse of keep-power-in-suspend
arm64: dts: rockchip: remove always-on and boot-on from vcc_sd
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 29 Oct 2016 18:09:11 +0000 (11:09 -0700)]
Merge tag 'arm-soc/for-4.9/devicetree-arm64-fixes' of github.com/Broadcom/stblinux into fixes
This pull request contains a single fix for Broadcom ARM64-based SoCs:
- Ray adds the required bus width and OOB sector size properties to the
Northstar 2 SVK reference board in order for the NAND controller to work
properly
* tag 'arm-soc/for-4.9/devicetree-arm64-fixes' of http://github.com/Broadcom/stblinux:
arm64: dts: Updated NAND DT properties for NS2 SVK
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 29 Oct 2016 18:08:50 +0000 (11:08 -0700)]
Merge tag 'imx-fixes-4.9' of git://git./linux/kernel/git/shawnguo/linux into fixes
The i.MX fixes for 4.9:
- A couple of patches from Fabio to fix the GPC power domain regression
which is caused by PM Domain core change
0159ec670763dd
("PM / Domains: Verify the PM domain is present when adding a
provider"), and a related kernel crash seen with multi_v7_defconfig
build.
- Correct the PHY ID mask for AR8031 to match phy driver code.
- Apply new added timer erratum
A008585 for LS1043A and LS2080A SoC.
- Correct vf610 global timer IRQ flag to avoid warning from gic driver
after commit
992345a58e0c ("irqchip/gic: WARN if setting the
interrupt type for a PPI fails").
* tag 'imx-fixes-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: mach-imx6q: Fix the PHY ID mask for AR8031
ARM: dts: vf610: fix IRQ flag of global timer
ARM: imx: gpc: Fix the imx_gpc_genpd_init() error path
ARM: imx: gpc: Initialize all power domains
arm64: dts: Add timer erratum property for LS2080A and LS1043A
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 29 Oct 2016 18:05:49 +0000 (11:05 -0700)]
Merge tag 'uniphier-fixes-v4.9' of git://git./linux/kernel/git/masahiroy/linux-uniphier into fixes
UniPhier ARM SoC fixes for v4.9
- Add "select ARCH_HAS_RESET_CONTROLLER" in Kconfig
- Rename wrongly-named mioctrl to sdctrl
* tag 'uniphier-fixes-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
arm64: dts: uniphier: change MIO node to SD control node
ARM: dts: uniphier: change MIO node to SD control node
reset: uniphier: rename MIO reset to SD reset for Pro5, PXs2, LD20 SoCs
arm64: uniphier: select ARCH_HAS_RESET_CONTROLLER
ARM: uniphier: select ARCH_HAS_RESET_CONTROLLER
Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Torvalds [Sat, 29 Oct 2016 17:57:40 +0000 (10:57 -0700)]
Merge tag 'driver-core-4.9-rc3' of git://git./linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are two small driver core / kernfs fixes for 4.9-rc3.
One makes the Kconfig entry for DEBUG_TEST_DRIVER_REMOVE a bit more
explicit that this is a crazy thing to enable for a distro kernel
(thanks for trying Fedora!), the other resolves an issue with vim
opening kernfs files (sysfs, configfs, etc.)
Both have been in linux-next with no reported issues"
* tag 'driver-core-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver core: Make Kconfig text for DEBUG_TEST_DRIVER_REMOVE stronger
kernfs: Add noop_fsync to supported kernfs_file_fops
Linus Torvalds [Sat, 29 Oct 2016 17:20:59 +0000 (10:20 -0700)]
Merge tag 'staging-4.9-rc3' of git://git./linux/kernel/git/gregkh/staging
Pull staging and IIO driver fixes from Greg KH:
"Here are some small staging and iio driver fixes for reported issues
for 4.9-rc3. Nothing major, the "largest" being a lustre fix for a
sysfs file that was obviously wrong, and had never been tested, so it
was moved to debugfs as that is where it belongs. The others are small
bug fixes for reported issues with various staging or iio drivers.
All have been in linux-next for a while with no reported issues"
* tag 'staging-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
greybus: fix a leak on error in gb_module_create()
greybus: es2: fix error return code in ap_probe()
greybus: arche-platform: Add missing of_node_put() in arche_platform_change_state()
staging: android: ion: Fix error handling in ion_query_heaps()
iio: accel: sca3000_core: avoid potentially uninitialized variable
iio:chemical:atlas-ph-sensor: Fix use of 32 bit int to hold 16 bit big endian value
staging/lustre/llite: Move unstable_stats from sysfs to debugfs
Staging: wilc1000: Fix kernel Oops on opening the device
staging: android/ion: testing the wrong variable
Staging: greybus: uart: Use gbphy_dev->dev instead of bundle->dev
Staging: greybus: gpio: Use gbphy_dev->dev instead of bundle->dev
iio: adc: ti-
adc081c: Select IIO_TRIGGERED_BUFFER to prevent build errors
iio: maxim_thermocouple: Align 16 bit big endian value of raw reads
Linus Torvalds [Sat, 29 Oct 2016 17:17:52 +0000 (10:17 -0700)]
Merge tag 'tty-4.9-rc3' of git://git./linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are a number of small tty and serial driver fixes for reported
issues for 4.9-rc3. Nothing major, but they do resolve a bunch of
problems with the tty core changes that are in 4.9-rc1, and finally
the atmel serial driver is back working properly.
All have been in linux-next with no reported issues"
* tag 'tty-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial_core: fix NULL struct tty pointer access in uart_write_wakeup
tty: serial_core: Fix serial console crash on port shutdown
tty/serial: at91: fix hardware handshake on Atmel platforms
vt: clear selection before resizing
sc16is7xx: always write state when configuring GPIO as an output
sh-sci: document R8A7743/5 support
tty: serial: 8250: 8250_core: NXP SC16C2552 workaround
tty: limit terminal size to 4M chars
tty: serial: fsl_lpuart: Fix Tx DMA edge case
serial: 8250_lpss: enable MSI for sure
serial: core: fix console problems on uart_close
serial: 8250_uniphier: fix clearing divisor latch access bit
serial: 8250_uniphier: fix more unterminated string
serial: pch_uart: add terminate entry for dmi_system_id tables
devicetree: bindings: uart: Add new compatible string for ZynqMP
serial: xuartps: Add new compatible string for ZynqMP
serial: SERIAL_STM32 should depend on HAS_DMA
serial: stm32: Fix comparisons with undefined register
tty: vt, fix bogus division in csi_J
Linus Torvalds [Sat, 29 Oct 2016 17:07:59 +0000 (10:07 -0700)]
Merge tag 'usb-4.9-rc3' of git://git./linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB driver fixes for 4.9-rc3.
There is the usual number of gadget and xhci patches in here to
resolved reported issues, as well as some usb-serial driver fixes and
new device ids.
All have been in linux-next with no reported issues"
* tag 'usb-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
usb: chipidea: host: fix NULL ptr dereference during shutdown
usb: renesas_usbhs: add wait after initialization for R-Car Gen3
usb: increase ohci watchdog delay to 275 msec
usb: musb: Call pm_runtime from musb_gadget_queue
usb: musb: Fix hardirq-safe hardirq-unsafe lock order error
usb: ehci-platform: increase EHCI_MAX_RSTS to 4
usb: ohci-at91: Set RemoteWakeupConnected bit explicitly.
USB: serial: fix potential NULL-dereference at probe
xhci: use default USB_RESUME_TIMEOUT when resuming ports.
xhci: workaround for hosts missing CAS bit
xhci: add restart quirk for Intel Wildcatpoint PCH
USB: serial: cp210x: fix tiocmget error handling
wusb: fix error return code in wusb_prf()
Revert "Documentation: devicetree: dwc2: Deprecate g-tx-fifo-size"
Revert "usb: dwc2: gadget: fix TX FIFO size and address initialization"
Revert "usb: dwc2: gadget: change variable name to more meaningful"
USB: serial: ftdi_sio: add support for Infineon TriBoard TC2X7
wusb: Stop using the stack for sg crypto scratch space
usb: dwc3: Fix size used in dma_free_coherent()
usb: gadget: f_fs: stop sleeping in ffs_func_eps_disable
...
Craig Gallek [Tue, 25 Oct 2016 22:08:49 +0000 (18:08 -0400)]
inet: Fix missing return value in inet6_hash
As part of a series to implement faster SO_REUSEPORT lookups,
commit
086c653f5862 ("sock: struct proto hash function may error")
added return values to protocol hash functions and
commit
496611d7b5ea ("inet: create IPv6-equivalent inet_hash function")
implemented a new hash function for IPv6. However, the latter does
not respect the former's convention.
This properly propagates the hash errors in the IPv6 case.
Fixes: 496611d7b5ea ("inet: create IPv6-equivalent inet_hash function")
Reported-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Craig Gallek <kraig@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 29 Oct 2016 16:00:41 +0000 (12:00 -0400)]
Merge branch 'mlx5-fixes'
Saeed Mahameed says:
====================
Mellanox 100G mlx5 fixes 2016-10-25
This series contains some bug fixes for the mlx5 core and mlx5e driver.
From Daniel:
- Cache line size determination at runtime, instead of using
L1_CACHE_BYTES hard coded value, use cache_line_size()
- Always Query HCA caps after setting them even on reset flow
From Mohamad:
- Reorder netdev cleanup to uregister netdev before detaching it
for the kernel to not complain about open resources such as vlans
- Change the acl enable prototype to return status, for better error
resiliency
- Clear health sick bit when starting health poll after reset flow
- Fix race between PCI error handlers and health work
- PCI error recovery health care simulation, in case when the kernel
PCI error handlers are not triggered for some internal firmware errors
From Noa:
- Avoid passing dma address 0 to firmware when mapping system pages
to the firmware
From Paul: Some straight forward flow steering fixes
- Keep autogroups list ordered
- Fix autogroups groups num not decreasing
- Correctly initialize last use of flow counters
From Saeed:
- Choose the nearest LRO timeout to the wanted one
instead of blindly choosing "dev_cap.lro_timeout[2]"
This series has no conflict with the for-next pull request posted
earlier today ("Mellanox mlx5 core driver updates 2016-10-25").
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Noa Osherovich [Tue, 25 Oct 2016 15:36:35 +0000 (18:36 +0300)]
net/mlx5: Avoid passing dma address 0 to firmware
Currently the firmware can't work with a page with dma address 0.
Passing such an address to the firmware will cause the give_pages
command to fail.
To avoid this, in case we get a 0 dma address of a page from the
dma engine, we avoid passing it to FW by remapping to get an address
other than 0.
Fixes: bf0bf77f6519 ('mlx5: Support communicating arbitrary host...')
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mohamad Haj Yahia [Tue, 25 Oct 2016 15:36:34 +0000 (18:36 +0300)]
net/mlx5: PCI error recovery health care simulation
In case that the kernel PCI error handlers are not called, we will
trigger our own recovery flow.
The health work will give priority to the kernel pci error handlers to
recover the PCI by waiting for a small period, if the pci error handlers
are not triggered the manual recovery flow will be executed.
We don't save pci state in case of manual recovery because it will ruin the
pci configuration space and we will lose dma sync.
Fixes: 89d44f0a6c73 ('net/mlx5_core: Add pci error handlers to mlx5_core driver')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mohamad Haj Yahia [Tue, 25 Oct 2016 15:36:33 +0000 (18:36 +0300)]
net/mlx5: Fix race between PCI error handlers and health work
Currently there is a race between the health care work and the kernel
pci error handlers because both of them detect the error, the first one
to be called will do the error handling.
There is a chance that health care will disable the pci after resuming
pci slot.
Also create a separate WQ because now we will have two types of health
works, one for the error detection and one for the recovery.
Fixes: 89d44f0a6c73 ('net/mlx5_core: Add pci error handlers to mlx5_core driver')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mohamad Haj Yahia [Tue, 25 Oct 2016 15:36:32 +0000 (18:36 +0300)]
net/mlx5: Clear health sick bit when starting health poll
The health sick status should be cleared when we start the health poll.
This is crucial for driver reload (unload + load) in order to behave
right in case of health issue.
Fixes: fd76ee4da55a ('net/mlx5_core: Fix internal error detection conditions')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mohamad Haj Yahia [Tue, 25 Oct 2016 15:36:31 +0000 (18:36 +0300)]
net/mlx5: Change the acl enable prototype to return status
The Ingress/Egress ACL enable function may fail and it should return
status to its caller to avoid NULL pointer dereference.
Fixes: f942380c1239 ('net/mlx5: E-Switch, Vport ingress/egress ACLs rules for spoofchk')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mohamad Haj Yahia [Tue, 25 Oct 2016 15:36:30 +0000 (18:36 +0300)]
net/mlx5e: Unregister netdev before detaching it
Detaching the netdev before unregistering it cause some netdev cleanup
ndos to fail because they check presence of the netdev, so we need to
unregister the netdev first.
Fixes: 26e59d8077a3 ('net/mlx5e: Implement mlx5e interface attach/detach callbacks')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Tue, 25 Oct 2016 15:36:29 +0000 (18:36 +0300)]
net/mlx5e: Choose best nearest LRO timeout
Instead of predicting the index of the wanted LRO timeout value from
hardware capabilities, look for the nearest LRO timeout value.
Fixes: 5c50368f3831 ('net/mlx5e: Light-weight netdev open/stop')
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Blakey [Tue, 25 Oct 2016 15:36:28 +0000 (18:36 +0300)]
net/mlx5: Correctly initialize last use of flow counters
Currently, last use timestamp is initialized to zero.
This is not the expected value by higher layers such as
when we do TC action offloading. To fix that, set it to
the current time, e.g when the counter/rule is offloaded.
This is the same behaviour of non-offloaded TC actions.
Fixes: 43a335e055bb ('mlx5_core: Flow counters infrastructure')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Blakey [Tue, 25 Oct 2016 15:36:27 +0000 (18:36 +0300)]
net/mlx5: Fix autogroups groups num not decreasing
Autogroups groups num is increased when creating a new flow group,
but is never decreased.
Now decreasing it when deleting a flow group.
Fixes: f0d22d187473 ('net/mlx5_core: Introduce flow steering autogrouped flow table')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Blakey [Tue, 25 Oct 2016 15:36:26 +0000 (18:36 +0300)]
net/mlx5: Keep autogroups list ordered
Finding a new autogroup range is done by going over a group list
sorted by each group start index. The search is stopped after finding
the first free range. Adding the newly created group to the list is
wrongly added to the end of the list regardless of its start index as
the parameter of where to insert it is ignored.
This commit makes sure to use that unused parameter to insert
it where requested.
Fixes: f0d22d187473 ('net/mlx5_core: Introduce flow steering autogrouped flow table')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Jurgens [Tue, 25 Oct 2016 15:36:25 +0000 (18:36 +0300)]
net/mlx5: Always Query HCA caps after setting them
Always query the HCA caps after setting them to update the capablities
data structures. Not doing so results in incorrect capabilities being
reported including max_dc, max_qp and several others.
Fixes: 59211bd3b632 ("net/mlx5: Split the load/unload flow into hardware
and software flows")
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Jurgens [Tue, 25 Oct 2016 15:36:24 +0000 (18:36 +0300)]
{net, ib}/mlx5: Make cache line size determination at runtime.
ARM 64B cache line systems have L1_CACHE_BYTES set to 128.
cache_line_size() will return the correct size.
Fixes: cf50b5efa2fe('net/mlx5_core/ib: New device capabilities
handling.')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcelo Ricardo Leitner [Tue, 25 Oct 2016 16:27:39 +0000 (14:27 -0200)]
sctp: validate chunk len before actually using it
Andrey Konovalov reported that KASAN detected that SCTP was using a slab
beyond the boundaries. It was caused because when handling out of the
blue packets in function sctp_sf_ootb() it was checking the chunk len
only after already processing the first chunk, validating only for the
2nd and subsequent ones.
The fix is to just move the check upwards so it's also validated for the
1st chunk.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Gleixner [Sat, 29 Oct 2016 11:42:42 +0000 (13:42 +0200)]
x86/smpboot: Init apic mapping before usage
The recent changes, which forced the registration of the boot cpu on UP
systems, which do not have ACPI tables, have been fixed for systems w/o
local APIC, but left a wreckage for systems which have neither ACPI nor
mptables, but the CPU has an APIC, e.g. virtualbox.
The boot process crashes in prefill_possible_map() as it wants to register
the boot cpu, which needs to access the local apic, but the local APIC is
not yet mapped.
There is no reason why init_apic_mapping() can't be invoked before
prefill_possible_map(). So instead of playing another silly early mapping
game, as the ACPI/mptables code does, we just move init_apic_mapping()
before the call to prefill_possible_map().
In hindsight, I should have noticed that combination earlier.
Sorry for the churn (also in stable)!
Fixes: ff8560512b8d ("x86/boot/smp: Don't try to poke disabled/non-existent APIC")
Reported-and-debugged-by: Michal Necasek <michal.necasek@oracle.com>
Reported-and-tested-by: Wolfgang Bauer <wbauer@tmo.at>
Cc: prarit@redhat.com
Cc: ville.syrjala@linux.intel.com
Cc: michael.thayer@oracle.com
Cc: knut.osmundsen@oracle.com
Cc: frank.mehnert@oracle.com
Cc: Borislav Petkov <bp@alien8.de>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1610282114380.5053@nanos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Linus Torvalds [Sat, 29 Oct 2016 01:34:19 +0000 (18:34 -0700)]
Merge tag 'acpi-4.9-rc3' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix recent ACPICA regressions, an older PCI IRQ management
regression, and an incorrect return value of a function in the APEI
code.
Specifics:
- Fix three ACPICA issues related to the interpreter locking and
introduced by recent changes in that area (Lv Zheng).
- Fix a PCI IRQ management regression introduced during the 4.7 cycle
and related to the configuration of shared IRQs on systems with an
ISA bus (Sinan Kaya).
- Fix up a return value of one function in the APEI code (Punit
Agrawal)"
* tag 'acpi-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPICA: Dispatcher: Fix interpreter locking around acpi_ev_initialize_region()
ACPICA: Dispatcher: Fix an unbalanced lock exit path in acpi_ds_auto_serialize_method()
ACPICA: Dispatcher: Fix order issue of method termination
ACPI / APEI: Fix incorrect return value of ghes_proc()
ACPI/PCI: pci_link: Include PIRQ_PENALTY_PCI_USING for ISA IRQs
ACPI/PCI: pci_link: penalize SCI correctly
ACPI/PCI/IRQ: assign ISA IRQ directly during early boot stages
Linus Torvalds [Sat, 29 Oct 2016 01:29:13 +0000 (18:29 -0700)]
Merge tag 'pm-4.9-rc3' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix two intel_pstate issues related to the way it works when the
scaling_governor sysfs attribute is set to "performance" and fix up
messages in the system suspend core code.
Specifics:
- Fix a missing KERN_CONT in a system suspend message by converting
the affected code to using pr_info() and pr_cont() instead of the
"raw" printk() (Jon Hunter).
- Make intel_pstate set the CPU P-state from its .set_policy()
callback when the scaling_governor sysfs attribute is set to
"performance" so that it interacts with NOHZ_FULL more predictably
which was the case before 4.7 (Rafael Wysocki).
- Make intel_pstate always request the maximum allowed P-state when
the scaling_governor sysfs attribute is set to "performance" to
prevent it from effectively ingoring that setting is some
situations (Rafael Wysocki)"
* tag 'pm-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: Always set max P-state in performance mode
PM / suspend: Fix missing KERN_CONT for suspend message
cpufreq: intel_pstate: Set P-state upfront in performance mode
Linus Torvalds [Sat, 29 Oct 2016 00:02:58 +0000 (17:02 -0700)]
Merge tag 'arc-4.9-rc3' of git://git./linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
- support IDU intc for UP builds
- support gz, lzma compressed uImage [Daniel Mentz]
- adjust /proc/cpuinfo for non-continuous cpu ids [Noam Camus]
- syscall for userspace cmpxchg assist for configs lacking hardware atomics
- rework of boot log printing mainly for identifying older arc700 cores
- retiring some old code, build toggles
* tag 'arc-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: module: print pretty section names
ARC: module: elide loop to save reference to .eh_frame
ARC: mm: retire ARC_DBG_TLB_MISS_COUNT...
ARC: build: retire old toggles
ARC: boot log: refactor cpu name/release printing
ARC: boot log: remove awkward space comma from MMU line
ARC: boot log: don't assume SWAPE instruction support
ARC: boot log: refactor printing abt features not captured in BCRs
ARCv2: boot log: print IOC exists as well as enabled status
ARCv2: IOC: use @ioc_enable not @ioc_exist where intended
ARC: syscall for userspace cmpxchg assist
ARC: fix build warning in elf.h
ARC: Adjust cpuinfo for non-continuous cpu ids
ARC: [build] Support gz, lzma compressed uImage
ARCv2: intc: untangle SMP, MCIP and IDU
Rafael J. Wysocki [Fri, 28 Oct 2016 23:58:03 +0000 (01:58 +0200)]
Merge branches 'acpica-fixes', 'acpi-pci-fixes' and 'acpi-apei-fixes'
* acpica-fixes:
ACPICA: Dispatcher: Fix interpreter locking around acpi_ev_initialize_region()
ACPICA: Dispatcher: Fix an unbalanced lock exit path in acpi_ds_auto_serialize_method()
ACPICA: Dispatcher: Fix order issue of method termination
* acpi-pci-fixes:
ACPI/PCI: pci_link: Include PIRQ_PENALTY_PCI_USING for ISA IRQs
ACPI/PCI: pci_link: penalize SCI correctly
ACPI/PCI/IRQ: assign ISA IRQ directly during early boot stages
* acpi-apei-fixes:
ACPI / APEI: Fix incorrect return value of ghes_proc()
Lv Zheng [Wed, 26 Oct 2016 07:42:01 +0000 (15:42 +0800)]
ACPICA: Dispatcher: Fix interpreter locking around acpi_ev_initialize_region()
In the code path of acpi_ev_initialize_region(), there is namespace
modification code unlocked. This patch tunes the code to make sure
such modification are always locked.
Fixes: 74f51b80a0c4 (ACPICA: Namespace: Fix dynamic table loading issues)
Tested-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lv Zheng [Wed, 26 Oct 2016 07:40:20 +0000 (15:40 +0800)]
ACPICA: Dispatcher: Fix an unbalanced lock exit path in acpi_ds_auto_serialize_method()
There is a lock unbalanced exit path in acpi_ds_initialize_method(),
this patch corrects it.
Fixes: 441ad11d078f (ACPICA: Dispatcher: Fix a mutex issue for method auto serialization)
Tested-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lv Zheng [Wed, 26 Oct 2016 07:40:12 +0000 (15:40 +0800)]
ACPICA: Dispatcher: Fix order issue of method termination
The last step of the method termination should be the end of the method
serialization. Otherwise, the steps happening after it will face the race
issues that cannot be protected by the method serialization mechanism.
This patch fixes this issue by moving the per-method-object deletion code
prior than the end of the method serialization. Otherwise, the possible
race issues may result in AE_ALREADY_EXISTS error in a parallel
environment.
Fixes: 74f51b80a0c4 (ACPICA: Namespace: Fix dynamic table loading issues)
Reported-and-tested-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Fri, 28 Oct 2016 23:52:28 +0000 (16:52 -0700)]
Merge tag 'powerpc-4.9-4' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Fixes marked for stable:
- Convert cmp to cmpd in idle enter sequence (Segher Boessenkool)
- cxl: Fix leaking pid refs in some error paths (Vaibhav Jain)
- Re-fix race condition between going idle and entering guest (Paul Mackerras)
- Fix race condition in setting lock bit in idle/wakeup code (Paul Mackerras)
- radix: Use tlbiel only if we ever ran on the current cpu (Aneesh Kumar K.V)
- relocation, register save fixes for system reset interrupt (Nicholas Piggin)
Fixes for code merged this cycle:
- Fix CONFIG_ALIVEC typo in restore_tm_state() (Valentin Rothberg)
- KVM: PPC: Book3S HV: Fix build error when SMP=n (Michael Ellerman)"
* tag 'powerpc-4.9-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: relocation, register save fixes for system reset interrupt
powerpc/mm/radix: Use tlbiel only if we ever ran on the current cpu
powerpc/process: Fix CONFIG_ALIVEC typo in restore_tm_state()
powerpc/64: Fix race condition in setting lock bit in idle/wakeup code
powerpc/64: Re-fix race condition between going idle and entering guest
cxl: Fix leaking pid refs in some error paths
powerpc: Convert cmp to cmpd in idle enter sequence
KVM: PPC: Book3S HV: Fix build error when SMP=n
Rafael J. Wysocki [Fri, 28 Oct 2016 23:29:17 +0000 (01:29 +0200)]
Merge branches 'pm-cpufreq-fixes' and 'pm-sleep-fixes'
* pm-cpufreq-fixes:
cpufreq: intel_pstate: Always set max P-state in performance mode
cpufreq: intel_pstate: Set P-state upfront in performance mode
* pm-sleep-fixes:
PM / suspend: Fix missing KERN_CONT for suspend message
Linus Torvalds [Fri, 28 Oct 2016 23:27:16 +0000 (16:27 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Misc kernel fixes: a virtualization environment related fix, an uncore
PMU driver removal handling fix, a PowerPC fix and new events for
Knights Landing"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Honour the CPUID for number of fixed counters in hypervisors
perf/powerpc: Don't call perf_event_disable() from atomic context
perf/core: Protect PMU device removal with a 'pmu_bus_running' check, to fix CONFIG_DEBUG_TEST_DRIVER_REMOVE=y kernel panic
perf/x86/intel/cstate: Add C-state residency events for Knights Landing
Linus Torvalds [Fri, 28 Oct 2016 18:47:45 +0000 (11:47 -0700)]
Merge branch 'libnvdimm-fixes' of git://git./linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"A build fix, a NULL de-reference found by static analysis, a misuse of
the percpu_ref_exit() (tagged for -stable), and notification of failed
attempts to clear media errors.
These patches have received a build success notification from the
0day- kbuild-robot and appeared in next-
20161028"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
device-dax: fix percpu_ref_exit ordering
nvdimm: make CONFIG_NVDIMM_DAX 'bool'
pmem: report error on clear poison failure
libnvdimm, namespace: potential NULL deref on allocation error
Linus Torvalds [Fri, 28 Oct 2016 18:31:06 +0000 (11:31 -0700)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Three arm64 fixes for -rc3. They're all pretty straightforward: a
couple of NUMA issues from the Huawei folks and a thinko in
__page_to_voff that seems to be benign, but is certainly better off
fixed.
Summary:
- couple of NUMA fixes
- thinko in __page_to_voff"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: fix __page_to_voff definition
arm64/numa: fix incorrect log for memory-less node
arm64/numa: fix pcpu_cpu_distance() to get correct CPU proximity
Linus Torvalds [Fri, 28 Oct 2016 18:28:14 +0000 (11:28 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes: three build fixes, an unwinder fix and a microcode loader
fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode/AMD: Fix more fallout from CONFIG_RANDOMIZE_MEMORY=y
x86: Fix export for mcount and __fentry__
x86/quirks: Hide maybe-uninitialized warning
x86/build: Fix build with older GCC versions
x86/unwind: Fix empty stack dereference in guess unwinder
Linus Torvalds [Fri, 28 Oct 2016 18:26:01 +0000 (11:26 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer fixes from Ingo Molnar:
"Fix four timer locking races: two were noticed by Linus while
reviewing the code while chasing for a corruption bug, and two
from fixing spurious USB timeouts"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timers: Prevent base clock corruption when forwarding
timers: Prevent base clock rewind when forwarding clock
timers: Lock base for same bucket optimization
timers: Plug locking race vs. timer migration
David S. Miller [Fri, 28 Oct 2016 17:43:56 +0000 (13:43 -0400)]
Merge branch 'mlxsw-fixes'
Jiri Pirko says:
====================
mlxsw: Couple of fixes
Couple of LPM tree management fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Tue, 25 Oct 2016 09:25:57 +0000 (11:25 +0200)]
mlxsw: spectrum_router: Compare only trees which are in use during tree get
Only trees which are in use should be compared to requested prefix usage.
Fixes: 53342023eed9 ("mlxsw: spectrum_router: Implement LPM trees management")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Tue, 25 Oct 2016 09:25:56 +0000 (11:25 +0200)]
mlxsw: spectrum_router: Save requested prefix bitlist when creating tree
Currently, the prefix bitlist is not saved for LPM trees, causing the
compare to always fail which causes the tree to be destroyed and created
for every inserted and removed FIB entry. So fix this by saving
the bitlist as it should have been done from the very beginning.
Fixes: 53342023eed9 ("mlxsw: spectrum_router: Implement LPM trees management")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 28 Oct 2016 17:12:27 +0000 (10:12 -0700)]
Merge branches 'core-urgent-for-linus', 'irq-urgent-for-linus' and 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull objtool, irq and scheduler fixes from Ingo Molnar:
"One more objtool fixlet for GCC6 code generation patterns, an irq
DocBook fix and an unused variable warning fix in the scheduler"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Fix rare switch jump table pattern detection
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
doc: Add missing parameter for msi_setup
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Remove unused but set variable 'rq'
Vineet Gupta [Tue, 25 Oct 2016 18:23:19 +0000 (11:23 -0700)]
ARC: module: print pretty section names
Now that we have referece to section name string table in
apply_relocate_add(), use it to
- print the name of section being relocated
- print symbol with NULL name (since it refers to a section)
before
| Section to fixup
7000a060
| =========================================================
| rela->r_off | rela->addend | sym->st_value | ADDR | VALUE
| =========================================================
| 1c 0
7000e000 7000a07c 7000e000 []
| 40 0
7000a000 7000a0a0 7000a000 []
after
| Section to fixup .eh_frame @
7000a060
| =========================================================
| r_off r_add st_value ADDRESS VALUE
| =========================================================
| 1c 0
7000e000 7000a07c 7000e000 [.init.text]
| 40 0
7000a000 7000a0a0 7000a000 [.exit.text]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Vineet Gupta [Tue, 25 Oct 2016 17:43:20 +0000 (10:43 -0700)]
ARC: module: elide loop to save reference to .eh_frame
The loop was really needed in .debug_frame regime where wanted make it
as SH_ALLOC so that apply_relocate_add() would process it. That's not
needed for .eh_frame, so we check this in apply_relocate_add() which
gets called for each section.
Note that we need to save reference to "section name strings" section in
module_frob_arch_sections() since apply_relocate_add() doesn't get that
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Vineet Gupta [Tue, 25 Oct 2016 15:58:17 +0000 (08:58 -0700)]
ARC: mm: retire ARC_DBG_TLB_MISS_COUNT...
... given that we have perf counters abel to do the same thing non
intrusively
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Vineet Gupta [Fri, 21 Oct 2016 23:04:37 +0000 (16:04 -0700)]
ARC: build: retire old toggles
These are really ancient toggles and tools no longer require them to be
passed. This paves way for deprecating them in long run.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Vineet Gupta [Thu, 27 Oct 2016 21:33:19 +0000 (14:33 -0700)]
ARC: boot log: refactor cpu name/release printing
The motivation is to identify ARC750 vs. ARC770 (we currently print
generic "ARC700").
A given ARC700 release could be 750 or 770, with same ARCNUM (or family
identifier which is unfortunate). The existing arc_cpu_tbl[] kept a single
concatenated string for core name and release which thus doesn't work
for 750 vs. 770 identification.
So split this into 2 tables, one with core names and other with release.
And while we are at it, get rid of the range checking for family numbers.
We just document the known to exist cores running Linux and ditch
others.
With this in place, we add detection of ARC750 which is
- cores 0x33 and before
- cores 0x34 and later with MMUv2
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Vineet Gupta [Tue, 25 Oct 2016 20:45:11 +0000 (13:45 -0700)]
ARC: boot log: remove awkward space comma from MMU line
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Vineet Gupta [Fri, 21 Oct 2016 01:08:10 +0000 (18:08 -0700)]
ARC: boot log: don't assume SWAPE instruction support
This came to light when helping a customer with oldish ARC750 core who
were getting instruction errors because of lack of SWAPE but boot log
was incorrectly printing it as being present
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Vineet Gupta [Fri, 21 Oct 2016 00:49:15 +0000 (17:49 -0700)]
ARC: boot log: refactor printing abt features not captured in BCRs
On older arc700 cores, some of the features configured were not present
in Build config registers. To print about them at boot, we just use the
Kconfig option i.e. whether linux is built to use them or not.
So yes this seems bogus, but what else can be done. Moreover if linux is
booting with these enabled, then the Kconfig info is a good indicator
anyways.
Over time these "hacks" accumulated in read_arc_build_cfg_regs() as well
as arc_cpu_mumbojumbo(). so refactor and move all of those in a single
place: read_arc_build_cfg_regs(). This causes some code redcution too:
| bloat-o-meter2 arch/arc/kernel/setup.o.0 arch/arc/kernel/setup.o.1
| add/remove: 0/0 grow/shrink: 2/1 up/down: 64/-132 (-68)
| function old new delta
| setup_processor 610 670 +60
| cpuinfo_arc700 76 80 +4
| arc_cpu_mumbojumbo 752 620 -132
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Linus Torvalds [Fri, 28 Oct 2016 17:07:35 +0000 (10:07 -0700)]
Merge branch 'for-linus-4.9' of git://git./linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"My patch fixes the btrfs list_head abuse that we tracked down during
Dave Jones' memory corruption investigation. With both Jens and my
patches in place, I'm no longer able to trigger problems.
Filipe is fixing a difficult old bug between snapshots, balance and
send. Dave is cooking a few more for the next rc, but these are tested
and ready"
* 'for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: fix races on root_log_ctx lists
btrfs: fix incremental send failure caused by balance
Vineet Gupta [Thu, 13 Oct 2016 22:53:02 +0000 (15:53 -0700)]
ARCv2: boot log: print IOC exists as well as enabled status
Previously we would not print the case when IOC existed but was not
enabled.
And while at it, reduce one line off boot printing by consolidating
the Peripheral address space and IO-Coherency which in a way
applies to them
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Linus Torvalds [Fri, 28 Oct 2016 17:00:44 +0000 (10:00 -0700)]
Merge tag 'sound-4.9-rc3' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This contains the usual stuff -- the fixups and quirks for HD-audio
and USB-audio, in addition to a bad regression fix in ALSA sequencer
timer since 4.8, and a trivial fix for asihpi PCI driver"
* tag 'sound-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Add quirk for Syntek STK1160
ALSA: seq: Fix time account regression
ALSA: hda - Fix surround output pins for ASRock B150M mobo
ALSA: hda - Fix headset mic detection problem for two Dell laptops
ALSA: asihpi: fix kernel memory disclosure
ALSA: hda - Adding a new group of pin cfg into ALC295 pin quirk table
ALSA: hda - allow 40 bit DMA mask for NVidia devices
Linus Torvalds [Fri, 28 Oct 2016 16:36:07 +0000 (09:36 -0700)]
Merge tag 'drm-x86-pat-regression-fix' of git://people.freedesktop.org/~airlied/linux
Pull drm x86/pat regression fixes from Dave Airlie:
"This is a standalone pull request for the fix for a regression
introduced in -rc1 by a change to vm_insert_mixed to start using the
PAT range tracking to validate page protections. With this fix in
place, all the VRAM mappings for GPU drivers ended up at UC instead of
WC.
There are probably better ways to fix this long term, but nothing I'd
considered for -fixes that wouldn't need more settling in time. So
I've just created a new arch API that the drivers can reserve all
their VRAM aperture ranges as WC"
* tag 'drm-x86-pat-regression-fix' of git://people.freedesktop.org/~airlied/linux:
drm/drivers: add support for using the arch wc mapping API.
x86/io: add interface to reserve io memtype for a resource range. (v1.1)
Linus Torvalds [Fri, 28 Oct 2016 16:27:58 +0000 (09:27 -0700)]
Merge tag 'dm-4.9-fixes' of git://git./linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- a couple DM raid and DM mirror fixes
- a couple .request_fn request-based DM NULL pointer fixes
- a fix for a DM target reference count leak, on target load error,
that prevented associated DM target kernel module(s) from being
removed
* tag 'dm-4.9-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm table: fix missing dm_put_target_type() in dm_table_add_target()
dm rq: clear kworker_task if kthread_run() returned an error
dm: free io_barrier after blk_cleanup_queue call
dm raid: fix activation of existing raid4/10 devices
dm mirror: use all available legs on multiple failures
dm mirror: fix read error on recovery after default leg failure
dm raid: fix compat_features validation
Linus Torvalds [Fri, 28 Oct 2016 16:23:59 +0000 (09:23 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jmorris/linux-security
Pull key fixes from James Morris:
- fix a buffer overflow when displaying /proc/keys [CVE-2016-7042].
- fix broken initialisation in the big_key implementation that can
result in an oops.
- make big_key depend on having a random number generator available in
Kconfig.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
security/keys: make BIG_KEYS dependent on stdrng.
KEYS: Sort out big_key initialisation
KEYS: Fix short sprintf buffer in /proc/keys show function
Richard Weinberger [Fri, 28 Oct 2016 09:49:03 +0000 (11:49 +0200)]
ubifs: Fix regression in ubifs_readdir()
Commit
c83ed4c9dbb35 ("ubifs: Abort readdir upon error") broke
overlayfs support because the fix exposed an internal error
code to VFS.
Reported-by: Peter Rosin <peda@axentia.se>
Tested-by: Peter Rosin <peda@axentia.se>
Reported-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Tested-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Fixes: c83ed4c9dbb35 ("ubifs: Abort readdir upon error")
Cc: stable@vger.kernel.org
Signed-off-by: Richard Weinberger <richard@nod.at>
Boris Brezillon [Fri, 28 Oct 2016 09:08:44 +0000 (11:08 +0200)]
ubi: fastmap: Fix add_vol() return value test in ubi_attach_fastmap()
Commit
e96a8a3bb671 ("UBI: Fastmap: Do not add vol if it already
exists") introduced a bug by changing the possible error codes returned
by add_vol():
- this function no longer returns NULL in case of allocation failure
but return ERR_PTR(-ENOMEM)
- when a duplicate entry in the volume RB tree is found it returns
ERR_PTR(-EEXIST) instead of ERR_PTR(-EINVAL)
Fix the tests done on add_vol() return val to match this new behavior.
Fixes: e96a8a3bb671 ("UBI: Fastmap: Do not add vol if it already exists")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Sheng Yong <shengyong1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Gabriel Krisman Bertazi [Tue, 4 Oct 2016 18:26:48 +0000 (15:26 -0300)]
MAINTAINERS: Add entry for genwqe driver
Frank and I maintain this
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Cc: haver@linux.vnet.ibm.com
Acked-by: Frank Haverkamp <haver@linux.vnet.ibm.com>=
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>