Thomas Gleixner [Fri, 2 Nov 2018 20:58:39 +0000 (21:58 +0100)]
Merge branch 'clockevents/4.20-rc1' of https://git.linaro.org/people/daniel.lezcano/linux into timers/urgent
Pull clockevent update from Daniel Lezcano:
- Add the per cpu timer for the c-sky architecture (Guo Ren)
- Add the global timer for the c-sky architecture (Guo Ren)
Guo Ren [Fri, 2 Nov 2018 16:51:31 +0000 (00:51 +0800)]
dt-bindings: timer: gx6605s SOC timer
Dt-bindings doc for gx6605s SOC's system timer.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Guo Ren [Fri, 2 Nov 2018 16:51:30 +0000 (00:51 +0800)]
clocksource/drivers/c-sky: Add gx6605s SOC system timer
The driver is for gx6605s SOC system timer and there are two
same timers in gx6605s. We use one for clkevt and another one for
clksrc.
The timer is mmio map to access, so we need give mmio address in dts.
The counter at 0x0 offset is clock event.
The counter at 0x40 offset is clock source.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Guo Ren [Fri, 2 Nov 2018 16:51:29 +0000 (00:51 +0800)]
dt-bindings: timer: C-SKY Multi-processor timer
Dt-bingdings doc for C-SKY SMP system setting.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Guo Ren [Fri, 2 Nov 2018 16:51:28 +0000 (00:51 +0800)]
clocksource/drivers/c-sky: Add C-SKY SMP timer
The driver is for C-SKY SMP timer. It only supports oneshot event
and 32bit overflow for clocksource. Per cpu core has one timer and
all timers share one clock-counter-input from the same clocksource.
This use mfcr&mtcr instructions to access the regs.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Greg Kroah-Hartman [Sat, 29 Sep 2018 21:52:14 +0000 (14:52 -0700)]
Merge tag 'for-linus-
20180929' of git://git.kernel.dk/linux-block
Jens writes:
"Block fixes for 4.19-rc6
A set of fixes that should go into this release. This pull request
contains:
- A fix (hopefully) for the persistent grants for xen-blkfront. A
previous fix from this series wasn't complete, hence reverted, and
this one should hopefully be it. (Boris Ostrovsky)
- Fix for an elevator drain warning with SMR devices, which is
triggered when you switch schedulers (Damien)
- bcache deadlock fix (Guoju Fang)
- Fix for the block unplug tracepoint, which has had the
timer/explicit flag reverted since 4.11 (Ilya)
- Fix a regression in this series where the blk-mq timeout hook is
invoked with the RCU read lock held, hence preventing it from
blocking (Keith)
- NVMe pull from Christoph, with a single multipath fix (Susobhan Dey)"
* tag 'for-linus-
20180929' of git://git.kernel.dk/linux-block:
xen/blkfront: correct purging of persistent grants
Revert "xen/blkfront: When purging persistent grants, keep them in the buffer"
blk-mq: I/O and timer unplugs are inverted in blktrace
bcache: add separate workqueue for journal_write to avoid deadlock
xen/blkfront: When purging persistent grants, keep them in the buffer
block: fix deadline elevator drain for zoned block devices
blk-mq: Allow blocking queue tag iter callbacks
nvme: properly propagate errors in nvme_mpath_init
Greg Kroah-Hartman [Sat, 29 Sep 2018 21:34:06 +0000 (14:34 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Thomas writes:
"A single fix for the AMD memory encryption boot code so it does not
read random garbage instead of the cached encryption bit when a kexec
kernel is allocated above the 32bit address limit."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot: Fix kexec booting failure in the SEV bit detection code
Greg Kroah-Hartman [Sat, 29 Sep 2018 21:32:49 +0000 (14:32 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Thomas writes:
"Three small fixes for clocksource drivers:
- Proper error handling in the Atmel PIT driver
- Add CLOCK_SOURCE_SUSPEND_NONSTOP for TI SoCs so suspend works again
- Fix the next event function for Facebook Backpack-CMM BMC chips so
usleep(100) doesnt sleep several milliseconds"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/timer-atmel-pit: Properly handle error cases
clocksource/drivers/fttmr010: Fix set_next_event handler
clocksource/drivers/ti-32k: Add CLOCK_SOURCE_SUSPEND_NONSTOP flag for non-am43 SoCs
Greg Kroah-Hartman [Sat, 29 Sep 2018 18:32:03 +0000 (11:32 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Thomas writes:
"A single fix for a missing sanity check when a pinned event is tried
to be read on the wrong CPU due to a legit event scheduling failure."
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Add sanity check to deal with pinned event failure
Greg Kroah-Hartman [Sat, 29 Sep 2018 13:50:36 +0000 (06:50 -0700)]
Merge tag 'pm-4.19-rc6' of git://git./linux/kernel/git/rafael/linux-pm
Rafael writes:
"Power management fix for 4.19-rc6
Fix incorrect __init and __exit annotations in the Qualcomm
Kryo cpufreq driver (Nathan Chancellor)."
* tag 'pm-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: qcom-kryo: Fix section annotations
Nathan Chancellor [Thu, 20 Sep 2018 00:22:21 +0000 (17:22 -0700)]
cpufreq: qcom-kryo: Fix section annotations
There is currently a warning when building the Kryo cpufreq driver into
the kernel image:
WARNING: vmlinux.o(.text+0x8aa424): Section mismatch in reference from
the function qcom_cpufreq_kryo_probe() to the function
.init.text:qcom_cpufreq_kryo_get_msm_id()
The function qcom_cpufreq_kryo_probe() references
the function __init qcom_cpufreq_kryo_get_msm_id().
This is often because qcom_cpufreq_kryo_probe lacks a __init
annotation or the annotation of qcom_cpufreq_kryo_get_msm_id is wrong.
Remove the '__init' annotation from qcom_cpufreq_kryo_get_msm_id
so that there is no more mismatch warning.
Additionally, Nick noticed that the remove function was marked as
'__init' when it should really be marked as '__exit'.
Fixes: 46e2856b8e18 (cpufreq: Add Kryo CPU scaling driver)
Fixes: 5ad7346b4ae2 (cpufreq: kryo: Add module remove and exit)
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.18+ <stable@vger.kernel.org> # 4.18+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Greg Kroah-Hartman [Sat, 29 Sep 2018 09:52:24 +0000 (02:52 -0700)]
Merge tag 'dma-mapping-4.19-3' of git://git.infradead.org/users/hch/dma-mapping
Christoph writes:
"dma mapping fix for 4.19-rc6
fix a missing Kconfig symbol for commits introduced in 4.19-rc"
* tag 'dma-mapping-4.19-3' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: add the missing ARCH_HAS_SYNC_DMA_FOR_CPU_ALL declaration
Greg Kroah-Hartman [Sat, 29 Sep 2018 01:04:50 +0000 (18:04 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Dmitry writes:
"Input updates for v4.19-rc5
Just a few driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: uinput - allow for max == min during input_absinfo validation
Input: elantech - enable middle button of touchpad on ThinkPad P72
Input: atakbd - fix Atari CapsLock behaviour
Input: atakbd - fix Atari keymap
Input: egalax_ts - add system wakeup support
Input: gpio-keys - fix a documentation index issue
Greg Kroah-Hartman [Sat, 29 Sep 2018 01:04:06 +0000 (18:04 -0700)]
Merge tag 'spi-fix-v4.19-rc5' of https://git./linux/kernel/git/broonie/spi
Mark writes:
"spi: Fixes for v4.19
Quite a few fixes for the Renesas drivers in here, plus a fix for the
Tegra driver and some documentation fixes for the recently added
spi-mem code. The Tegra fix is relatively large but fairly
straightforward and mechanical, it runs on probe so it's been
reasonably well covered in -next testing."
* tag 'spi-fix-v4.19-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-mem: Move the DMA-able constraint doc to the kerneldoc header
spi: spi-mem: Add missing description for data.nbytes field
spi: rspi: Fix interrupted DMA transfers
spi: rspi: Fix invalid SPI use during system suspend
spi: sh-msiof: Fix handling of write value for SISTR register
spi: sh-msiof: Fix invalid SPI use during system suspend
spi: gpio: Fix copy-and-paste error
spi: tegra20-slink: explicitly enable/disable clock
Greg Kroah-Hartman [Sat, 29 Sep 2018 01:02:25 +0000 (18:02 -0700)]
Merge tag 'regulator-v4.19-rc5' of https://git./linux/kernel/git/broonie/regulator
Mark writes:
"regulator: Fixes for 4.19
A collection of fairly minor bug fixes here, a couple of driver
specific ones plus two core fixes. There's one fix for the new
suspend state code which fixes some confusion with constant values
that are supposed to indicate noop operation and another fixing a
race condition with the creation of sysfs files on new regulators."
* tag 'regulator-v4.19-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: fix crash caused by null driver data
regulator: Fix 'do-nothing' value for regulators without suspend state
regulator: da9063: fix DT probing with constraints
regulator:
bd71837: Disable voltage monitoring for LDO3/4
Greg Kroah-Hartman [Sat, 29 Sep 2018 00:43:32 +0000 (17:43 -0700)]
Merge tag 'powerpc-4.19-3' of https://git./linux/kernel/git/powerpc/linux
Michael writes:
"powerpc fixes for 4.19 #3
A reasonably big batch of fixes due to me being away for a few weeks.
A fix for the TM emulation support on Power9, which could result in
corrupting the guest r11 when running under KVM.
Two fixes to the TM code which could lead to userspace GPR corruption
if we take an SLB miss at exactly the wrong time.
Our dynamic patching code had a bug that meant we could patch freed
__init text, which could lead to corrupting userspace memory.
csum_ipv6_magic() didn't work on little endian platforms since we
optimised it recently.
A fix for an endian bug when reading a device tree property telling
us how many storage keys the machine has available.
Fix a crash seen on some configurations of PowerVM when migrating the
partition from one machine to another.
A fix for a regression in the setup of our CPU to NUMA node mapping
in KVM guests.
A fix to our selftest Makefiles to make them work since a recent
change to the shared Makefile logic."
* tag 'powerpc-4.19-3' of https://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
selftests/powerpc: Fix Makefiles for headers_install change
powerpc/numa: Use associativity if VPHN hcall is successful
powerpc/tm: Avoid possible userspace r1 corruption on reclaim
powerpc/tm: Fix userspace r13 corruption
powerpc/pseries: Fix unitialized timer reset on migration
powerpc/pkeys: Fix reading of ibm, processor-storage-keys property
powerpc: fix csum_ipv6_magic() on little endian platforms
powerpc/powernv/ioda2: Reduce upper limit for DMA window size (again)
powerpc: Avoid code patching freed init sections
KVM: PPC: Book3S HV: Fix guest r11 corruption with POWER9 TM workarounds
Greg Kroah-Hartman [Sat, 29 Sep 2018 00:42:44 +0000 (17:42 -0700)]
Merge tag 'pinctrl-v4.19-4' of git://git./linux/kernel/git/linusw/linux-pinctrl
Linus writes:
"Pin control fixes for v4.19:
- Fixes to x86 hardware:
- AMD interrupt debounce issues
- Faulty Intel cannonlake register offset
- Revert pin translation IRQ locking"
* tag 'pinctrl-v4.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
Revert "pinctrl: intel: Do pin translation when lock IRQ"
pinctrl: cannonlake: Fix HOSTSW_OWN register offset of H variant
pinctrl/amd: poll InterruptEnable bits in amd_gpio_irq_set_type
Reinette Chatre [Wed, 19 Sep 2018 17:29:06 +0000 (10:29 -0700)]
perf/core: Add sanity check to deal with pinned event failure
It is possible that a failure can occur during the scheduling of a
pinned event. The initial portion of perf_event_read_local() contains
the various error checks an event should pass before it can be
considered valid. Ensure that the potential scheduling failure
of a pinned event is checked for and have a credible error.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: fenghua.yu@intel.com
Cc: tony.luck@intel.com
Cc: acme@kernel.org
Cc: gavin.hindman@intel.com
Cc: jithu.joseph@intel.com
Cc: dave.hansen@intel.com
Cc: hpa@zytor.com
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/6486385d1f30336e9973b24c8c65f5079543d3d3.1537377064.git.reinette.chatre@intel.com
Greg Kroah-Hartman [Fri, 28 Sep 2018 16:55:17 +0000 (18:55 +0200)]
Merge tag 'drm-fixes-2018-09-28' of git://anongit.freedesktop.org/drm/drm
Dave writes:
"drm fixes for 4.19-rc6
Looks like a pretty normal week for graphics,
core: syncobj fix, panel link regression revert
amd: suspend/resume fixes, EDID emulation fix
mali-dp: NV12 writeback and vblank reset fixes
etnaviv: DMA setup fix"
* tag 'drm-fixes-2018-09-28' of git://anongit.freedesktop.org/drm/drm:
drm/amd/display: Fix Edid emulation for linux
drm/amd/display: Fix Vega10 lightup on S3 resume
drm/amdgpu: Fix vce work queue was not cancelled when suspend
Revert "drm/panel: Add device_link from panel device to DRM device"
drm/syncobj: Don't leak fences when WAIT_FOR_SUBMIT is set
drm/malidp: Fix writeback in NV12
drm: mali-dp: Call drm_crtc_vblank_reset on device init
drm/etnaviv: add DMA configuration for etnaviv platform device
Greg Kroah-Hartman [Fri, 28 Sep 2018 16:53:22 +0000 (18:53 +0200)]
Merge tag 'riscv-for-linus-4.19-rc6' of git://git./linux/kernel/git/palmer/riscv-linux
Palmer writes:
"A Single RISC-V Update for 4.19-rc6
The Debian guys have been pushing on our port and found some
unversioned symbols leaking into modules. This PR contains a single
fix for that issue."
* tag 'riscv-for-linus-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
RISC-V: include linux/ftrace.h in asm-prototypes.h
Greg Kroah-Hartman [Fri, 28 Sep 2018 16:20:41 +0000 (18:20 +0200)]
Merge tag 'pci-v4.19-fixes-2' of ssh://gitolite./linux/kernel/git/helgaas/pci
Bjorn writes:
"PCI fixes:
- Fix ACPI hotplug issue that causes black screen crash at boot (Mika
Westerberg)
- Fix DesignWare "scheduling while atomic" issues (Jisheng Zhang)
- Add PPC contacts to MAINTAINERS for PCI core error handling (Bjorn
Helgaas)
- Sort Mobiveil MAINTAINERS entry (Lorenzo Pieralisi)"
* tag 'pci-v4.19-fixes-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
ACPI / hotplug / PCI: Don't scan for non-hotplug bridges if slot is not bridge
PCI: dwc: Fix scheduling while atomic issues
MAINTAINERS: Move mobiveil PCI driver entry where it belongs
MAINTAINERS: Update PPC contacts for PCI core error handling
Jens Axboe [Fri, 28 Sep 2018 15:41:40 +0000 (09:41 -0600)]
Merge branch 'nvme-4.19' of git://git.infradead.org/nvme into for-linus
Pull NVMe fix from Christoph.
* 'nvme-4.19' of git://git.infradead.org/nvme:
nvme: properly propagate errors in nvme_mpath_init
Juergen Gross [Fri, 28 Sep 2018 07:28:27 +0000 (09:28 +0200)]
xen/blkfront: correct purging of persistent grants
Commit
a46b53672b2c2e3770b38a4abf90d16364d2584b ("xen/blkfront: cleanup
stale persistent grants") introduced a regression as purged persistent
grants were not pu into the list of free grants again. Correct that.
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Fri, 28 Sep 2018 15:40:17 +0000 (09:40 -0600)]
Revert "xen/blkfront: When purging persistent grants, keep them in the buffer"
Fix didn't work for all cases, reverting to add a (hopefully)
better fix.
This reverts commit
f151ba989d149bbdfc90e5405724bbea094f9b17.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Michael Ellerman [Fri, 28 Sep 2018 04:53:18 +0000 (14:53 +1000)]
selftests/powerpc: Fix Makefiles for headers_install change
Commit
b2d35fa5fc80 ("selftests: add headers_install to lib.mk")
introduced a requirement that Makefiles more than one level below the
selftests directory need to define top_srcdir, but it didn't update
any of the powerpc Makefiles.
This broke building all the powerpc selftests with eg:
make[1]: Entering directory '/src/linux/tools/testing/selftests/powerpc'
BUILD_TARGET=/src/linux/tools/testing/selftests/powerpc/alignment; mkdir -p $BUILD_TARGET; make OUTPUT=$BUILD_TARGET -k -C alignment all
make[2]: Entering directory '/src/linux/tools/testing/selftests/powerpc/alignment'
../../lib.mk:20: ../../../../scripts/subarch.include: No such file or directory
make[2]: *** No rule to make target '../../../../scripts/subarch.include'.
make[2]: Failed to remake makefile '../../../../scripts/subarch.include'.
Makefile:38: recipe for target 'alignment' failed
Fix it by setting top_srcdir in the affected Makefiles.
Fixes: b2d35fa5fc80 ("selftests: add headers_install to lib.mk")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Dave Airlie [Thu, 27 Sep 2018 23:30:11 +0000 (09:30 +1000)]
Merge branch 'drm-fixes-4.19' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Just a few fixes for 4.19:
- Couple of suspend/resume fixes
- Fix EDID emulation with DC
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927155418.2813-1-alexander.deucher@amd.com
Dave Airlie [Thu, 27 Sep 2018 23:25:26 +0000 (09:25 +1000)]
Merge tag 'drm-misc-fixes-2018-09-27-1' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
- Revert adding device-link to panels
- Don't leak fences in drm/syncobj
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927152712.GA53076@art_vandelay
Greg Kroah-Hartman [Thu, 27 Sep 2018 19:53:55 +0000 (21:53 +0200)]
Merge tag 'for-linus' of git://git./linux/kernel/git/rdma/rdma
Jason writes:
"Second RDMA rc pull request
- Fix a long standing race bug when destroying comp_event file descriptors
- srp, hfi1, bnxt_re: Various driver crashes from missing validation
and other cases
- Fixes for regressions in patches merged this window in the gid
cache, devx, ucma and uapi."
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/core: Set right entry state before releasing reference
IB/mlx5: Destroy the DEVX object upon error flow
IB/uverbs: Free uapi on destroy
RDMA/bnxt_re: Fix system crash during RDMA resource initialization
IB/hfi1: Fix destroy_qp hang after a link down
IB/hfi1: Fix context recovery when PBC has an UnsupportedVL
IB/hfi1: Invalid user input can result in crash
IB/hfi1: Fix SL array bounds check
RDMA/uverbs: Fix validity check for modify QP
IB/srp: Avoid that sg_reset -d ${srp_device} triggers an infinite loop
ucma: fix a use-after-free in ucma_resolve_ip()
RDMA/uverbs: Atomically flush and mark closed the comp event queue
cxgb4: fix abort_req_rss6 struct
Greg Kroah-Hartman [Thu, 27 Sep 2018 19:16:24 +0000 (21:16 +0200)]
Merge tag 'for_v4.19-rc6' of git://git./linux/kernel/git/jack/linux-fs
Jan writes:
"an ext2 patch fixing fsync(2) for DAX mounts."
* tag 'for_v4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
ext2, dax: set ext2_dax_aops for dax files
Ilya Dryomov [Wed, 26 Sep 2018 12:35:50 +0000 (14:35 +0200)]
blk-mq: I/O and timer unplugs are inverted in blktrace
trace_block_unplug() takes true for explicit unplugs and false for
implicit unplugs. schedule() unplugs are implicit and should be
reported as timer unplugs. While correct in the legacy code, this has
been inverted in blk-mq since 4.11.
Cc: stable@vger.kernel.org
Fixes: bd166ef183c2 ("blk-mq-sched: add framework for MQ capable IO schedulers")
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Kairui Song [Thu, 27 Sep 2018 12:38:45 +0000 (20:38 +0800)]
x86/boot: Fix kexec booting failure in the SEV bit detection code
Commit
1958b5fc4010 ("x86/boot: Add early boot support when running with SEV active")
can occasionally cause system resets when kexec-ing a second kernel even
if SEV is not active.
That's because get_sev_encryption_bit() uses 32-bit rIP-relative
addressing to read the value of enc_bit - a variable which caches a
previously detected encryption bit position - but kexec may allocate
the early boot code to a higher location, beyond the 32-bit addressing
limit.
In this case, garbage will be read and get_sev_encryption_bit() will
return the wrong value, leading to accessing memory with the wrong
encryption setting.
Therefore, remove enc_bit, and thus get rid of the need to do 32-bit
rIP-relative addressing in the first place.
[ bp: massage commit message heavily. ]
Fixes: 1958b5fc4010 ("x86/boot: Add early boot support when running with SEV active")
Suggested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Kairui Song <kasong@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: linux-kernel@vger.kernel.org
Cc: tglx@linutronix.de
Cc: mingo@redhat.com
Cc: hpa@zytor.com
Cc: brijesh.singh@amd.com
Cc: kexec@lists.infradead.org
Cc: dyoung@redhat.com
Cc: bhe@redhat.com
Cc: ghook@redhat.com
Link: https://lkml.kernel.org/r/20180927123845.32052-1-kasong@redhat.com
Guoju Fang [Thu, 27 Sep 2018 15:41:46 +0000 (23:41 +0800)]
bcache: add separate workqueue for journal_write to avoid deadlock
After write SSD completed, bcache schedules journal_write work to
system_wq, which is a public workqueue in system, without WQ_MEM_RECLAIM
flag. system_wq is also a bound wq, and there may be no idle kworker on
current processor. Creating a new kworker may unfortunately need to
reclaim memory first, by shrinking cache and slab used by vfs, which
depends on bcache device. That's a deadlock.
This patch create a new workqueue for journal_write with WQ_MEM_RECLAIM
flag. It's rescuer thread will work to avoid the deadlock.
Signed-off-by: Guoju Fang <fangguoju@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Bhawanpreet Lakha [Wed, 26 Sep 2018 17:42:10 +0000 (13:42 -0400)]
drm/amd/display: Fix Edid emulation for linux
[Why]
EDID emulation didn't work properly for linux, as we stop programming
if nothing is connected physically.
[How]
We get a flag from DRM when we want to do edid emulation. We check if
this flag is true and nothing is connected physically, if so we only
program the front end using VIRTUAL_SIGNAL.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Roman Li [Wed, 26 Sep 2018 17:42:16 +0000 (13:42 -0400)]
drm/amd/display: Fix Vega10 lightup on S3 resume
[Why]
There have been a few reports of Vega10 display remaining blank
after S3 resume. The regression is caused by workaround for mode
change on Vega10 - skip set_bandwidth if stream count is 0.
As a result we skipped dispclk reset on suspend, thus on resume
we may skip the clock update assuming it hasn't been changed.
On some systems it causes display blank or 'out of range'.
[How]
Revert "drm/amd/display: Fix Vega10 black screen after mode change"
Verified that it hadn't cause mode change regression.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rex Zhu [Thu, 27 Sep 2018 12:48:39 +0000 (20:48 +0800)]
drm/amdgpu: Fix vce work queue was not cancelled when suspend
The vce cancel_delayed_work_sync never be called.
driver call the function in error path.
This caused the A+A suspend hang when runtime pm enebled.
As we will visit the smu in the idle queue. this will cause
smu hang because the dgpu has been suspend, and the dgpu also
will be waked up. As the smu has been hang, so the dgpu resume
will failed.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Linus Walleij [Thu, 27 Sep 2018 12:41:30 +0000 (14:41 +0200)]
Revert "drm/panel: Add device_link from panel device to DRM device"
This reverts commit
0c08754b59da5557532d946599854e6df28edc22.
commit
0c08754b59da
("drm/panel: Add device_link from panel device to DRM device")
creates a circular dependency under these circumstances:
1. The panel depends on dsi-host because it is MIPI-DSI child
device.
2. dsi-host depends on the drm parent device (connector->dev->dev)
this should be allowed.
3. drm parent dev (connector->dev->dev) depends on the panel
after this patch.
This makes the dependency circular and while it appears it
does not affect any in-tree drivers (they do not seem to have
dsi hosts depending on the same parent device) this does not
seem right.
As noted in a response from Andrzej Hajda, the intent is
likely to make the panel dependent on the DRM device
(connector->dev) not its parent. But we have no way of
doing that since the DRM device doesn't contain any
struct device on its own (arguably it should).
Revert this until a proper approach is figured out.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927124130.9102-1-linus.walleij@linaro.org
Thomas Gleixner [Thu, 27 Sep 2018 14:50:22 +0000 (16:50 +0200)]
Merge branch 'clockevents/4.19-fixes' of https://git.linaro.org/people/daniel.lezcano/linux into timers/urgent
Pull another fix from Daniel Lezcano, which felt through the cracks:
- Fix a potential memory leak reported by smatch in the atmel timer driver
Boris Ostrovsky [Sat, 22 Sep 2018 19:55:49 +0000 (15:55 -0400)]
xen/blkfront: When purging persistent grants, keep them in the buffer
Commit
a46b53672b2c ("xen/blkfront: cleanup stale persistent grants")
added support for purging persistent grants when they are not in use. As
part of the purge, the grants were removed from the grant buffer, This
eventually causes the buffer to become empty, with BUG_ON triggered in
get_free_grant(). This can be observed even on an idle system, within
20-30 minutes.
We should keep the grants in the buffer when purging, and only free the
grant ref.
Fixes: a46b53672b2c ("xen/blkfront: cleanup stale persistent grants")
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Alexandre Belloni [Wed, 25 Apr 2018 10:14:39 +0000 (12:14 +0200)]
clocksource/drivers/timer-atmel-pit: Properly handle error cases
The smatch utility reports a possible leak:
smatch warnings:
drivers/clocksource/timer-atmel-pit.c:183 at91sam926x_pit_dt_init() warn: possible memory leak of 'data'
Ensure data is freed before exiting with an error.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Damien Le Moal [Thu, 27 Sep 2018 01:55:13 +0000 (10:55 +0900)]
block: fix deadline elevator drain for zoned block devices
When the deadline scheduler is used with a zoned block device, writes
to a zone will be dispatched one at a time. This causes the warning
message:
deadline: forced dispatching is broken (nr_sorted=X), please report this
to be displayed when switching to another elevator with the legacy I/O
path while write requests to a zone are being retained in the scheduler
queue.
Prevent this message from being displayed when executing
elv_drain_elevator() for a zoned block device. __blk_drain_queue() will
loop until all writes are dispatched and completed, resulting in the
desired elevator queue drain without extensive modifications to the
deadline code itself to handle forced-dispatch calls.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Fixes: 8dc8146f9c92 ("deadline-iosched: Introduce zone locking support")
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Dave Airlie [Thu, 27 Sep 2018 00:49:44 +0000 (10:49 +1000)]
Merge branch 'for-upstream/malidp-fixes' of git://linux-arm.org/linux-ld into drm-fixes
Fix NV12 writeback and fix vblank reset.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Liviu Dudau <Liviu.Dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180921112354.GR936@e110455-lin.cambridge.arm.com
Dave Airlie [Thu, 27 Sep 2018 00:19:26 +0000 (10:19 +1000)]
Merge branch 'etnaviv/fixes' of https://git.pengutronix.de/git/lst/linux into drm-fixes
one fix to get a proper DMA configuration in place for the etnaviv
virtual device. I'm sending this as a fix, as a dma-mapping change at
the ARC architecture side during the 4.19 cycle broke etnaviv on this
platform, which gets remedied with this patch, but it also enables
ARM64.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Lucas Stach <l.stach@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/ea1f712bf09bf9439c6b092bf2c2bde7bb01cf5e.camel@pengutronix.de
Mika Westerberg [Wed, 26 Sep 2018 20:39:28 +0000 (15:39 -0500)]
ACPI / hotplug / PCI: Don't scan for non-hotplug bridges if slot is not bridge
HP 6730b laptop has an ethernet NIC connected to one of the PCIe root
ports. The root ports themselves are native PCIe hotplug capable. Now,
during boot after PCI devices are scanned the BIOS triggers ACPI bus check
directly to the NIC:
ACPI: \_SB_.PCI0.RP06.NIC_: Bus check in hotplug_event()
It is not clear why it is sending bus check but regardless the ACPI hotplug
notify handler calls enable_slot() directly (instead of going through
acpiphp_check_bridge() as there is no bridge), which ends up handling
special case for non-hotplug bridges with native PCIe hotplug. This
results a crash of some kind but the reporter only sees black screen so it
is hard to figure out the exact spot and what actually happens. Based on
a few fix proposals it was tracked to crash somewhere inside
pci_assign_unassigned_bridge_resources().
In any case we should not really be in that special branch at all because
the ACPI notify happened to a slot that is not a PCI bridge (it is just a
regular PCI device).
Fix this so that we only go to that special branch if we are calling
enable_slot() for a bridge (e.g., the ACPI notification was for the
bridge).
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201127
Fixes: 84c8b58ed3ad ("ACPI / hotplug / PCI: Don't scan bridges managed by native hotplug")
Reported-by: Peter Anemone <peter.anemone@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: stable@vger.kernel.org # v4.18+
Jason Ekstrand [Wed, 26 Sep 2018 07:17:03 +0000 (02:17 -0500)]
drm/syncobj: Don't leak fences when WAIT_FOR_SUBMIT is set
We attempt to get fences earlier in the hopes that everything will
already have fences and no callbacks will be needed. If we do succeed
in getting a fence, getting one a second time will result in a duplicate
ref with no unref. This is causing memory leaks in Vulkan applications
that create a lot of fences; playing for a few hours can, apparently,
bring down the system.
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107899
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180926071703.15257-1-jason.ekstrand@intel.com
Greg Kroah-Hartman [Wed, 26 Sep 2018 11:08:53 +0000 (13:08 +0200)]
Merge tag 'iommu-fixes-v4.19-rc5' of git://git./linux/kernel/git/joro/iommu
Joerg writes:
"IOMMU Fixes for Linux v4.19-rc5
Three fixes queued up:
- Warning fix for Rockchip IOMMU where there were IRQ handlers
for offlined hardware.
- Fix for Intel VT-d because recent changes caused boot failures
on some machines because it tried to allocate to much
contiguous memory.
- Fix for AMD IOMMU to handle eMMC devices correctly that appear
as ACPI HID devices."
* tag 'iommu-fixes-v4.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Return devid as alias for ACPI HID devices
iommu/vt-d: Handle memory shortage on pasid table allocation
iommu/rockchip: Free irqs in shutdown handler
Arindam Nath [Tue, 18 Sep 2018 10:10:58 +0000 (15:40 +0530)]
iommu/amd: Return devid as alias for ACPI HID devices
ACPI HID devices do not actually have an alias for
them in the IVRS. But dev_data->alias is still used
for indexing into the IOMMU device table for devices
being handled by the IOMMU. So for ACPI HID devices,
we simply return the corresponding devid as an alias,
as parsed from IVRS table.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Fixes: 2bf9a0a12749 ('iommu/amd: Add iommu support for ACPI HID devices')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Keith Busch [Tue, 25 Sep 2018 16:36:20 +0000 (10:36 -0600)]
blk-mq: Allow blocking queue tag iter callbacks
A recent commit runs tag iterator callbacks under the rcu read lock,
but existing callbacks do not satisfy the non-blocking requirement.
The commit intended to prevent an iterator from accessing a queue that's
being modified. This patch fixes the original issue by taking a queue
reference instead of reading it, which allows callbacks to make blocking
calls.
Fixes: f5bbbbe4d6357 ("blk-mq: sync the update nr_hw_queues with blk_mq_queue_tag_busy_iter")
Acked-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Susobhan Dey [Tue, 25 Sep 2018 19:29:15 +0000 (12:29 -0700)]
nvme: properly propagate errors in nvme_mpath_init
Signed-off-by: Susobhan Dey <susobhan.dey@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Christoph Hellwig [Tue, 11 Sep 2018 09:00:49 +0000 (11:00 +0200)]
dma-mapping: add the missing ARCH_HAS_SYNC_DMA_FOR_CPU_ALL declaration
The patch adding the infrastructure failed to actually add the symbol
declaration, oops..
Fixes: faef87723a ("dma-noncoherent: add a arch_sync_dma_for_cpu_all hook")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Parav Pandit [Tue, 25 Sep 2018 09:10:40 +0000 (12:10 +0300)]
RDMA/core: Set right entry state before releasing reference
Currently add_modify_gid() for IB link layer has followong issue
in cache update path.
When GID update event occurs, core releases reference to the GID
table without updating its state and/or entry pointer.
CPU-0 CPU-1
------ -----
ib_cache_update() IPoIB ULP
add_modify_gid() [..]
put_gid_entry()
refcnt = 0, but
state = valid,
entry is valid.
(work item is not yet executed).
ipoib_create_ah()
rdma_create_ah()
rdma_get_gid_attr() <--
Tries to acquire gid_attr
which has refcnt = 0.
This is incorrect.
GID entry state and entry pointer is provides the accurate GID enty
state. Such fields must be updated with rwlock to protect against
readers and, such fields must be in sane state before refcount can drop
to zero. Otherwise above race condition can happen leading to
use-after-free situation.
Following backtrace has been observed when cache update for an IB port
is triggered while IPoIB ULP is creating an AH.
Therefore, when updating GID entry, first mark a valid entry as invalid
through state and set the barrier so that no callers can acquired
the GID entry, followed by release reference to it.
refcount_t: increment on 0; use-after-free.
WARNING: CPU: 4 PID: 29106 at lib/refcount.c:153 refcount_inc_checked+0x30/0x50
Workqueue: ib-comp-unb-wq ib_cq_poll_work [ib_core]
RIP: 0010:refcount_inc_checked+0x30/0x50
RSP: 0018:
ffff8802ad36f600 EFLAGS:
00010082
RAX:
0000000000000000 RBX:
0000000000000000 RCX:
0000000000000000
RDX:
0000000000000002 RSI:
0000000000000008 RDI:
ffffffff86710100
RBP:
ffff8802d6e60a30 R08:
ffffed005d67bf8b R09:
ffffed005d67bf8b
R10:
0000000000000001 R11:
ffffed005d67bf8a R12:
ffff88027620cee8
R13:
ffff8802d6e60988 R14:
ffff8802d6e60a78 R15:
0000000000000202
FS:
0000000000000000(0000) GS:
ffff8802eb200000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00007f3ab35e5c88 CR3:
00000002ce84a000 CR4:
00000000000006e0
IPv6: ADDRCONF(NETDEV_CHANGE): ib1: link becomes ready
Call Trace:
rdma_get_gid_attr+0x220/0x310 [ib_core]
? lock_acquire+0x145/0x3a0
rdma_fill_sgid_attr+0x32c/0x470 [ib_core]
rdma_create_ah+0x89/0x160 [ib_core]
? rdma_fill_sgid_attr+0x470/0x470 [ib_core]
? ipoib_create_ah+0x52/0x260 [ib_ipoib]
ipoib_create_ah+0xf5/0x260 [ib_ipoib]
ipoib_mcast_join_complete+0xbbe/0x2540 [ib_ipoib]
Fixes: b150c3862d21 ("IB/core: Introduce GID entry reference counts")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Yishai Hadas [Tue, 25 Sep 2018 09:11:12 +0000 (12:11 +0300)]
IB/mlx5: Destroy the DEVX object upon error flow
Upon DEVX object creation the object must be destroyed upon a follows
error flow.
Fixes: 7efce3691d33 ("IB/mlx5: Add obj create and destroy functionality")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Mark Bloch [Tue, 25 Sep 2018 08:23:55 +0000 (11:23 +0300)]
IB/uverbs: Free uapi on destroy
Make sure we free struct uverbs_api once we clean the radix tree. It was
allocated by uverbs_alloc_api().
Fixes: 9ed3e5f44772 ("IB/uverbs: Build the specs into a radix tree at runtime")
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Greg Kroah-Hartman [Tue, 25 Sep 2018 19:37:41 +0000 (21:37 +0200)]
erge tag 'libnvdimm-fixes-4.19-rc6' of git://git./linux/kernel/git/nvdimm/nvdimm
Dan writes:
"libnvdimm/dax for 4.19-rc6
* (2) fixes for the dax error handling updates that were merged for
v4.19-rc1. My mails to Al have been bouncing recently, so I do not have
his ack but the uaccess change is of the trivial / obviously correct
variety. The address_space_operations fixes a regression.
* A filesystem-dax fix to correct the zero page lookup to be compatible
with non-x86 (mips and s390) architectures."
* tag 'libnvdimm-fixes-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
device-dax: Add missing address_space_operations
uaccess: Fix is_source param for check_copy_size() in copy_to_iter_mcsafe()
filesystem-dax: Fix use of zero page
Greg Kroah-Hartman [Tue, 25 Sep 2018 16:14:14 +0000 (18:14 +0200)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
James writes:
"SCSI fixes on
20180925
Nine obvious bug fixes mostly in individual drivers. The target fix
is of particular importance because it's CVE related."
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sd: don't crash the host on invalid commands
scsi: ipr: System hung while dlpar adding primary ipr adapter back
scsi: target: iscsi: Use bin2hex instead of a re-implementation
scsi: target: iscsi: Use hex2bin instead of a re-implementation
scsi: lpfc: Synchronize access to remoteport via rport
scsi: ufs: Disable blk-mq for now
scsi: sd: Contribute to randomness when running rotational device
scsi: ibmvscsis: Ensure partition name is properly NUL terminated
scsi: ibmvscsis: Fix a stringop-overflow warning
Greg Kroah-Hartman [Tue, 25 Sep 2018 15:54:55 +0000 (17:54 +0200)]
Merge tag 'usb-4.19-rc6' of git://git./linux/kernel/git/gregkh/usb
I wrote:
"USB fixes for 4.19-rc6
Here are some small USB core and driver fixes for reported issues for
4.19-rc6.
The most visible is the oops fix for when the USB core is built into the
kernel that is present in 4.18. Turns out not many people actually do
that so it went unnoticed for a while. The rest is some tiny typec,
musb, and other core fixes.
All have been in linux-next with no reported issues."
* tag 'usb-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: mux: Take care of driver module reference counting
usb: core: safely deal with the dynamic quirk lists
usb: roles: Take care of driver module reference counting
USB: handle NULL config in usb_find_alt_setting()
USB: fix error handling in usb_driver_claim_interface()
USB: remove LPM management from usb_driver_claim_interface()
USB: usbdevfs: restore warning for nonsensical flags
USB: usbdevfs: sanitize flags more
Revert "usb: cdc-wdm: Fix a sleep-in-atomic-context bug in service_outstanding_interrupt()"
usb: musb: dsps: do not disable CPPI41 irq in driver teardown
Greg Kroah-Hartman [Tue, 25 Sep 2018 15:22:50 +0000 (17:22 +0200)]
Merge tag 'tty-4.19-rc6' of git://git./linux/kernel/git/gregkh/tty
I wrote:
"TTY/Serial driver fixes for 4.19-rc6
Here are a number of small tty and serial driver fixes for reported
issues for 4.19-rc6.
One should hopefully resolve a much-reported issue that syzbot has found
in the tty layer. Although there are still more issues there, getting
this fixed is nice to see finally happen.
All of these have been in linux-next for a while with no reported
issues."
* tag 'tty-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: imx: restore handshaking irq for imx1
tty: vt_ioctl: fix potential Spectre v1
tty: Drop tty->count on tty_reopen() failure
serial: cpm_uart: return immediately from console poll
tty: serial: lpuart: avoid leaking struct tty_struct
serial: mvebu-uart: Fix reporting of effective CSIZE to userspace
Greg Kroah-Hartman [Tue, 25 Sep 2018 15:01:52 +0000 (17:01 +0200)]
Merge tag 'char-misc-4.19-rc6' of git://git./linux/kernel/git/gregkh/char-misc
Greg (well I), wrote:
"Char/Misc driver fixes for 4.19-rc6
Here are some soundwire and intel_th (tracing) driver fixes for some
reported issues.
All of these have been in linux-next for a week with no reported issues."
* tag 'char-misc-4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
intel_th: pci: Add Ice Lake PCH support
intel_th: Fix resource handling for ACPI glue layer
intel_th: Fix device removal logic
soundwire: Fix acquiring bus lock twice during master release
soundwire: Fix incorrect exit after configuring stream
soundwire: Fix duplicate stream state assignment
Srikar Dronamraju [Tue, 25 Sep 2018 12:25:15 +0000 (17:55 +0530)]
powerpc/numa: Use associativity if VPHN hcall is successful
Currently associativity is used to lookup node-id even if the
preceding VPHN hcall failed. However this can cause CPU to be made
part of the wrong node, (most likely to be node 0). This is because
VPHN is not enabled on KVM guests.
With
2ea6263 ("powerpc/topology: Get topology for shared processors at
boot"), associativity is used to set to the wrong node. Hence KVM
guest topology is broken.
For example : A 4 node KVM guest before would have reported.
[root@localhost ~]# numactl -H
available: 4 nodes (0-3)
node 0 cpus: 0 1 2 3
node 0 size: 1746 MB
node 0 free: 1604 MB
node 1 cpus: 4 5 6 7
node 1 size: 2044 MB
node 1 free: 1765 MB
node 2 cpus: 8 9 10 11
node 2 size: 2044 MB
node 2 free: 1837 MB
node 3 cpus: 12 13 14 15
node 3 size: 2044 MB
node 3 free: 1903 MB
node distances:
node 0 1 2 3
0: 10 40 40 40
1: 40 10 40 40
2: 40 40 10 40
3: 40 40 40 10
Would now report:
[root@localhost ~]# numactl -H
available: 4 nodes (0-3)
node 0 cpus: 0 2 3 4 5 6 7 8 9 10 11 12 13 14 15
node 0 size: 1746 MB
node 0 free: 1244 MB
node 1 cpus:
node 1 size: 2044 MB
node 1 free: 2032 MB
node 2 cpus: 1
node 2 size: 2044 MB
node 2 free: 2028 MB
node 3 cpus:
node 3 size: 2044 MB
node 3 free: 2032 MB
node distances:
node 0 1 2 3
0: 10 40 40 40
1: 40 10 40 40
2: 40 40 10 40
3: 40 40 40 10
Fix this by skipping associativity lookup if the VPHN hcall failed.
Fixes: 2ea626306810 ("powerpc/topology: Get topology for shared processors at boot")
Signed-off-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Neuling [Tue, 25 Sep 2018 09:36:47 +0000 (19:36 +1000)]
powerpc/tm: Avoid possible userspace r1 corruption on reclaim
Current we store the userspace r1 to PACATMSCRATCH before finally
saving it to the thread struct.
In theory an exception could be taken here (like a machine check or
SLB miss) that could write PACATMSCRATCH and hence corrupt the
userspace r1. The SLB fault currently doesn't touch PACATMSCRATCH, but
others do.
We've never actually seen this happen but it's theoretically
possible. Either way, the code is fragile as it is.
This patch saves r1 to the kernel stack (which can't fault) before we
turn MSR[RI] back on. PACATMSCRATCH is still used but only with
MSR[RI] off. We then copy r1 from the kernel stack to the thread
struct once we have MSR[RI] back on.
Suggested-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Neuling [Mon, 24 Sep 2018 07:27:04 +0000 (17:27 +1000)]
powerpc/tm: Fix userspace r13 corruption
When we treclaim we store the userspace checkpointed r13 to a scratch
SPR and then later save the scratch SPR to the user thread struct.
Unfortunately, this doesn't work as accessing the user thread struct
can take an SLB fault and the SLB fault handler will write the same
scratch SPRG that now contains the userspace r13.
To fix this, we store r13 to the kernel stack (which can't fault)
before we access the user thread struct.
Found by running P8 guest + powervm + disable_1tb_segments + TM. Seen
as a random userspace segfault with r13 looking like a kernel address.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Lu Baolu [Sat, 8 Sep 2018 01:42:53 +0000 (09:42 +0800)]
iommu/vt-d: Handle memory shortage on pasid table allocation
Pasid table memory allocation could return failure due to memory
shortage. Limit the pasid table size to 1MiB because current 8MiB
contiguous physical memory allocation can be hard to come by. W/o
a PASID table, the device could continue to work with only shared
virtual memory impacted. So, let's go ahead with context mapping
even the memory allocation for pasid table failed.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107783
Fixes: cc580e41260d ("iommu/vt-d: Per PCI device pasid table interfaces")
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Reported-and-tested-by: Pelton Kyle D <kyle.d.pelton@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Lubomir Rintel [Mon, 24 Sep 2018 12:18:34 +0000 (13:18 +0100)]
Revert "uapi/linux/keyctl.h: don't use C++ reserved keyword as a struct member name"
This changes UAPI, breaking iwd and libell:
ell/key.c: In function 'kernel_dh_compute':
ell/key.c:205:38: error: 'struct keyctl_dh_params' has no member named 'private'; did you mean 'dh_private'?
struct keyctl_dh_params params = { .private = private,
^~~~~~~
dh_private
This reverts commit
8a2336e549d385bb0b46880435b411df8d8200e8.
Fixes: 8a2336e549d3 ("uapi/linux/keyctl.h: don't use C++ reserved keyword as a struct member name")
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Randy Dunlap <rdunlap@infradead.org>
cc: Mat Martineau <mathew.j.martineau@linux.intel.com>
cc: Stephan Mueller <smueller@chronox.de>
cc: James Morris <jmorris@namei.org>
cc: "Serge E. Hallyn" <serge@hallyn.com>
cc: Mat Martineau <mathew.j.martineau@linux.intel.com>
cc: Andrew Morton <akpm@linux-foundation.org>
cc: Linus Torvalds <torvalds@linux-foundation.org>
cc: <stable@vger.kernel.org>
Signed-off-by: James Morris <james.morris@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mika Westerberg [Mon, 24 Sep 2018 14:32:12 +0000 (17:32 +0300)]
Revert "pinctrl: intel: Do pin translation when lock IRQ"
This reverts commit
55aedef50d4d810670916d9fce4a40d5da2079e7.
Commit
55aedef50d4d ("pinctrl: intel: Do pin translation when lock IRQ")
added special translation from GPIO number to hardware pin number to
irq_reqres/relres hooks to avoid failure when IRQs are requested. The
actual failure happened inside gpiochip_lock_as_irq() because it calls
gpiod_get_direction() and pinctrl-intel.c::intel_gpio_get_direction()
implementation originally missed the translation so the two hooks made
it work by skipping the ->get_direction() call entirely (it overwrote
the default GPIOLIB provided functions).
The proper fix that adds translation to GPIO callbacks was merged with
commit
96147db1e1df ("pinctrl: intel: Do pin translation in other GPIO
operations as well"). This allows us to use the default GPIOLIB provided
functions again.
In addition as find out by Benjamin Tissoires the two functions
(intel_gpio_irq_reqres()/intel_gpio_irq_relres()) now cause problems of
their own because they operate on pin numbers and pass that pin number
to gpiochip_lock_as_irq() which actually expects a GPIO number.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199911
Fixes: 55aedef50d4d ("pinctrl: intel: Do pin translation when lock IRQ")
Reported-and-tested-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Mika Westerberg [Mon, 24 Sep 2018 14:32:11 +0000 (17:32 +0300)]
pinctrl: cannonlake: Fix HOSTSW_OWN register offset of H variant
It turns out the HOSTSW_OWN register offset is different between LP and
H variants. The latter should use 0xc0 instead so fix that.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199911
Fixes: a663ccf0fea1 ("pinctrl: intel: Add Intel Cannon Lake PCH-H pin controller support")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Daniel Kurtz [Sat, 22 Sep 2018 19:58:26 +0000 (13:58 -0600)]
pinctrl/amd: poll InterruptEnable bits in amd_gpio_irq_set_type
From the AMD BKDG, if WAKE_INT_MASTER_REG.MaskStsEn is set, a software
write to the debounce registers of *any* gpio will block wake/interrupt
status generation for *all* gpios for a length of time that depends on
WAKE_INT_MASTER_REG.MaskStsLength[11:0]. During this period the Interrupt
Delivery bit (INTERRUPT_ENABLE) will read as 0.
In commit
4c1de0414a1340 ("pinctrl/amd: poll InterruptEnable bits in
enable_irq") we tried to fix this same "gpio Interrupts are blocked
immediately after writing debounce registers" problem, but incorrectly
assumed it only affected the gpio whose debounce was being configured
and not ALL gpios.
To solve this for all gpios, we move the polling loop from
amd_gpio_irq_enable() to amd_gpio_irq_set_type(), while holding the gpio
spinlock. This ensures that another gpio operation (e.g.
amd_gpio_irq_unmask()) can read a temporarily disabled IRQ and
incorrectly disable it while trying to modify some other register bits.
Fixes: 4c1de0414a1340 pinctrl/amd: poll InterruptEnable bits in enable_irq
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Greg Kroah-Hartman [Tue, 25 Sep 2018 09:19:28 +0000 (11:19 +0200)]
Merge gitolite./pub/scm/linux/kernel/git/davem/net
Dave writes:
"Networking fixes:
1) Fix multiqueue handling of coalesce timer in stmmac, from Jose
Abreu.
2) Fix memory corruption in NFC, from Suren Baghdasaryan.
3) Don't write reserved bits in ravb driver, from Kazuya Mizuguchi.
4) SMC bug fixes from Karsten Graul, YueHaibing, and Ursula Braun.
5) Fix TX done race in mvpp2, from Antoine Tenart.
6) ipv6 metrics leak, from Wei Wang.
7) Adjust firmware version requirements in mlxsw, from Petr Machata.
8) Fix autonegotiation on resume in r8169, from Heiner Kallweit.
9) Fixed missing entries when dumping /proc/net/if_inet6, from Jeff
Barnhill.
10) Fix double free in devlink, from Dan Carpenter.
11) Fix ethtool regression from UFO feature removal, from Maciej
Żenczykowski.
12) Fix drivers that have a ndo_poll_controller() that captures the
cpu entirely on loaded hosts by trying to drain all rx and tx
queues, from Eric Dumazet.
13) Fix memory corruption with jumbo frames in aquantia driver, from
Friedemann Gerold."
* gitolite.kernel.org:/pub/scm/linux/kernel/git/davem/net: (79 commits)
net: mvneta: fix the remaining Rx descriptor unmapping issues
ip_tunnel: be careful when accessing the inner header
mpls: allow routes on ip6gre devices
net: aquantia: memory corruption on jumbo frames
tun: remove ndo_poll_controller
nfp: remove ndo_poll_controller
bnxt: remove ndo_poll_controller
bnx2x: remove ndo_poll_controller
mlx5: remove ndo_poll_controller
mlx4: remove ndo_poll_controller
i40evf: remove ndo_poll_controller
ice: remove ndo_poll_controller
igb: remove ndo_poll_controller
ixgb: remove ndo_poll_controller
fm10k: remove ndo_poll_controller
ixgbevf: remove ndo_poll_controller
ixgbe: remove ndo_poll_controller
bonding: use netpoll_poll_dev() helper
netpoll: make ndo_poll_controller() optional
rds: Fix build regression.
...
Heiko Stuebner [Mon, 27 Aug 2018 10:56:24 +0000 (12:56 +0200)]
iommu/rockchip: Free irqs in shutdown handler
In the iommu's shutdown handler we disable runtime-pm which could
result in the irq-handler running unclocked and since commit
3fc7c5c0cff3 ("iommu/rockchip: Handle errors returned from PM framework")
we warn about that fact.
This can cause warnings on shutdown on some Rockchip machines, so
free the irqs in the shutdown handler before we disable runtime-pm.
Reported-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Fixes: 3fc7c5c0cff3 ("iommu/rockchip: Handle errors returned from PM framework")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
James Cowgill [Thu, 6 Sep 2018 21:57:56 +0000 (22:57 +0100)]
RISC-V: include linux/ftrace.h in asm-prototypes.h
Building a riscv kernel with CONFIG_FUNCTION_TRACER and
CONFIG_MODVERSIONS enabled results in these two warnings:
MODPOST vmlinux.o
WARNING: EXPORT symbol "return_to_handler" [vmlinux] version generation failed, symbol will not be versioned.
WARNING: EXPORT symbol "_mcount" [vmlinux] version generation failed, symbol will not be versioned.
When exporting symbols from an assembly file, the MODVERSIONS code
requires their prototypes to be defined in asm-prototypes.h (see
scripts/Makefile.build). Since both of these symbols have prototypes
defined in linux/ftrace.h, include this header from RISC-V's
asm-prototypes.h.
Reported-by: Karsten Merker <merker@debian.org>
Signed-off-by: James Cowgill <jcowgill@debian.org>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Antoine Tenart [Mon, 24 Sep 2018 14:56:13 +0000 (16:56 +0200)]
net: mvneta: fix the remaining Rx descriptor unmapping issues
With CONFIG_DMA_API_DEBUG enabled we get DMA unmapping warning in
various places of the mvneta driver, for example when putting down an
interface while traffic is passing through.
The issue is when using s/w buffer management, the Rx buffers are mapped
using dma_map_page but unmapped with dma_unmap_single. This patch fixes
this by using the right unmapping function.
Fixes: 562e2f467e71 ("net: mvneta: Improve the buffer allocation method for SWBM")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Mon, 24 Sep 2018 13:48:19 +0000 (15:48 +0200)]
ip_tunnel: be careful when accessing the inner header
Cong noted that we need the same checks introduced by commit
76c0ddd8c3a6
("ip6_tunnel: be careful when accessing the inner header")
even for ipv4 tunnels.
Fixes: c54419321455 ("GRE: Refactor GRE tunneling code.")
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saif Hasan [Fri, 21 Sep 2018 21:30:05 +0000 (14:30 -0700)]
mpls: allow routes on ip6gre devices
Summary:
This appears to be necessary and sufficient change to enable `MPLS` on
`ip6gre` tunnels (RFC4023).
This diff allows IP6GRE devices to be recognized by MPLS kernel module
and hence user can configure interface to accept packets with mpls
headers as well setup mpls routes on them.
Test Plan:
Test plan consists of multiple containers connected via GRE-V6 tunnel.
Then carrying out testing steps as below.
- Carry out necessary sysctl settings on all containers
```
sysctl -w net.mpls.platform_labels=65536
sysctl -w net.mpls.ip_ttl_propagate=1
sysctl -w net.mpls.conf.lo.input=1
```
- Establish IP6GRE tunnels
```
ip -6 tunnel add name if_1_2_1 mode ip6gre \
local 2401:db00:21:6048:feed:0::1 \
remote 2401:db00:21:6048:feed:0::2 key 1
ip link set dev if_1_2_1 up
sysctl -w net.mpls.conf.if_1_2_1.input=1
ip -4 addr add 169.254.0.2/31 dev if_1_2_1 scope link
ip -6 tunnel add name if_1_3_1 mode ip6gre \
local 2401:db00:21:6048:feed:0::1 \
remote 2401:db00:21:6048:feed:0::3 key 1
ip link set dev if_1_3_1 up
sysctl -w net.mpls.conf.if_1_3_1.input=1
ip -4 addr add 169.254.0.4/31 dev if_1_3_1 scope link
```
- Install MPLS encap rules on node-1 towards node-2
```
ip route add 192.168.0.11/32 nexthop encap mpls 32/64 \
via inet 169.254.0.3 dev if_1_2_1
```
- Install MPLS forwarding rules on node-2 and node-3
```
// node2
ip -f mpls route add 32 via inet 169.254.0.7 dev if_2_4_1
// node3
ip -f mpls route add 64 via inet 169.254.0.12 dev if_4_3_1
```
- Ping 192.168.0.11 (node4) from 192.168.0.1 (node1) (where routing
towards 192.168.0.1 is via IP route directly towards node1 from node4)
```
ping 192.168.0.11
```
- tcpdump on interface to capture ping packets wrapped within MPLS
header which inturn wrapped within IP6GRE header
```
16:43:41.121073 IP6
2401:db00:21:6048:feed::1 > 2401:db00:21:6048:feed::2:
DSTOPT GREv0, key=0x1, length 100:
MPLS (label 32, exp 0, ttl 255) (label 64, exp 0, [S], ttl 255)
IP 192.168.0.1 > 192.168.0.11:
ICMP echo request, id 1208, seq 45, length 64
0x0000: 6000 2cdb 006c 3c3f 2401 db00 0021 6048 `.,..l<?$....!`H
0x0010: feed 0000 0000 0001 2401 db00 0021 6048 ........$....!`H
0x0020: feed 0000 0000 0002 2f00 0401 0401 0100 ......../.......
0x0030: 2000 8847 0000 0001 0002 00ff 0004 01ff ...G............
0x0040: 4500 0054 3280 4000 ff01 c7cb c0a8 0001 E..T2.@.........
0x0050: c0a8 000b 0800 a8d7 04b8 002d 2d3c a05b ...........--<.[
0x0060: 0000 0000 bcd8 0100 0000 0000 1011 1213 ................
0x0070: 1415 1617 1819 1a1b 1c1d 1e1f 2021 2223 .............!"#
0x0080: 2425 2627 2829 2a2b 2c2d 2e2f 3031 3233 $%&'()*+,-./0123
0x0090: 3435 3637 4567
```
Signed-off-by: Saif Hasan <has@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 24 Sep 2018 17:08:45 +0000 (10:08 -0700)]
Merge git://git./pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2018-09-24
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Several fixes for BPF sockmap to only allow sockets being attached in
ESTABLISHED state, from John.
2) Fix up the license to LGPL/BSD for the libc compat header which contains
fallback helpers that libbpf and bpftool is using, from Jakub.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Selvin Xavier [Fri, 21 Sep 2018 05:33:00 +0000 (22:33 -0700)]
RDMA/bnxt_re: Fix system crash during RDMA resource initialization
bnxt_re_ib_reg acquires and releases the rtnl lock whenever it accesses
the L2 driver.
The following sequence can trigger a crash
Acquires the rtnl_lock ->
Registers roce driver callback with L2 driver ->
release the rtnl lock
bnxt_re acquires the rtnl_lock ->
Request for MSIx vectors ->
release the rtnl_lock
Issue happens when bnxt_re proceeds with remaining part of initialization
and L2 driver invokes bnxt_ulp_irq_stop as a part of bnxt_open_nic.
The crash is in bnxt_qplib_nq_stop_irq as the NQ structures are
not initialized yet,
<snip>
[ 3551.726647] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 3551.726656] IP: [<
ffffffffc0840ee9>] bnxt_qplib_nq_stop_irq+0x59/0xb0 [bnxt_re]
[ 3551.726674] PGD 0
[ 3551.726679] Oops: 0002 1 SMP
...
[ 3551.726822] Hardware name: Dell Inc. PowerEdge R720/08RW36, BIOS 2.4.3 07/09/2014
[ 3551.726826] task:
ffff97e30eec5ee0 ti:
ffff97e3173bc000 task.ti:
ffff97e3173bc000
[ 3551.726829] RIP: 0010:[<
ffffffffc0840ee9>] [<
ffffffffc0840ee9>]
bnxt_qplib_nq_stop_irq+0x59/0xb0 [bnxt_re]
...
[ 3551.726872] Call Trace:
[ 3551.726886] [<
ffffffffc082cb9e>] bnxt_re_stop_irq+0x4e/0x70 [bnxt_re]
[ 3551.726899] [<
ffffffffc07d6a53>] bnxt_ulp_irq_stop+0x43/0x70 [bnxt_en]
[ 3551.726908] [<
ffffffffc07c82f4>] bnxt_reserve_rings+0x174/0x1e0 [bnxt_en]
[ 3551.726917] [<
ffffffffc07cafd8>] __bnxt_open_nic+0x368/0x9a0 [bnxt_en]
[ 3551.726925] [<
ffffffffc07cb62b>] bnxt_open_nic+0x1b/0x50 [bnxt_en]
[ 3551.726934] [<
ffffffffc07cc62f>] bnxt_setup_mq_tc+0x11f/0x260 [bnxt_en]
[ 3551.726943] [<
ffffffffc07d5f58>] bnxt_dcbnl_ieee_setets+0xb8/0x1f0 [bnxt_en]
[ 3551.726954] [<
ffffffff890f983a>] dcbnl_ieee_set+0x9a/0x250
[ 3551.726966] [<
ffffffff88fd6d21>] ? __alloc_skb+0xa1/0x2d0
[ 3551.726972] [<
ffffffff890f72fa>] dcb_doit+0x13a/0x210
[ 3551.726981] [<
ffffffff89003ff7>] rtnetlink_rcv_msg+0xa7/0x260
[ 3551.726989] [<
ffffffff88ffdb00>] ? rtnl_unicast+0x20/0x30
[ 3551.726996] [<
ffffffff88bf9dc8>] ? __kmalloc_node_track_caller+0x58/0x290
[ 3551.727002] [<
ffffffff890f7326>] ? dcb_doit+0x166/0x210
[ 3551.727007] [<
ffffffff88fd6d0d>] ? __alloc_skb+0x8d/0x2d0
[ 3551.727012] [<
ffffffff89003f50>] ? rtnl_newlink+0x880/0x880
...
[ 3551.727104] [<
ffffffff8911f7d5>] system_call_fastpath+0x1c/0x21
...
[ 3551.727164] RIP [<
ffffffffc0840ee9>] bnxt_qplib_nq_stop_irq+0x59/0xb0 [bnxt_re]
[ 3551.727175] RSP <
ffff97e3173bf788>
[ 3551.727177] CR2:
0000000000000000
Avoid this inconsistent state and system crash by acquiring
the rtnl lock for the entire duration of device initialization.
Re-factor the code to remove the rtnl lock from the individual function
and acquire and release it from the caller.
Fixes: 1ac5a4047975 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Fixes: 6e04b1035689 ("RDMA/bnxt_re: Fix broken RoCE driver due to recent L2 driver changes")
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Greg Kroah-Hartman [Mon, 24 Sep 2018 13:16:41 +0000 (15:16 +0200)]
Merge tag 'media/v4.19-2' of git://git./linux/kernel/git/mchehab/linux-media
Mauro briefly writes:
"media fixes for v4.19-rc5
some drivers and Kbuild fixes"
* tag 'media/v4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: platform: fix cros-ec-cec build error
media: staging/media/mt9t031/Kconfig: remove bogus entry
media: i2c: mt9v111: Fix v4l2-ctrl error handling
media: camss: add missing includes
media: camss: Use managed memory allocations
media: camss: mark PM functions as __maybe_unused
media: af9035: prevent buffer overflow on write
media: video_function_calls.rst: drop obsolete video-set-attributes reference
Michael Bringmann [Thu, 20 Sep 2018 16:45:13 +0000 (11:45 -0500)]
powerpc/pseries: Fix unitialized timer reset on migration
After migration of a powerpc LPAR, the kernel executes code to
update the system state to reflect new platform characteristics.
Such changes include modifications to device tree properties provided
to the system by PHYP. Property notifications received by the
post_mobility_fixup() code are passed along to the kernel in general
through a call to of_update_property() which in turn passes such
events back to all modules through entries like the '.notifier_call'
function within the NUMA module.
When the NUMA module updates its state, it resets its event timer. If
this occurs after a previous call to stop_topology_update() or on a
system without VPHN enabled, the code runs into an unitialized timer
structure and crashes. This patch adds a safety check along this path
toward the problem code.
An example crash log is as follows.
ibmvscsi
30000081: Re-enabling adapter!
------------[ cut here ]------------
kernel BUG at kernel/time/timer.c:958!
Oops: Exception in kernel mode, sig: 5 [#1]
LE SMP NR_CPUS=2048 NUMA pSeries
Modules linked in: nfsv3 nfs_acl nfs tcp_diag udp_diag inet_diag lockd unix_diag af_packet_diag netlink_diag grace fscache sunrpc xts vmx_crypto pseries_rng sg binfmt_misc ip_tables xfs libcrc32c sd_mod ibmvscsi ibmveth scsi_transport_srp dm_mirror dm_region_hash dm_log dm_mod
CPU: 11 PID: 3067 Comm: drmgr Not tainted 4.17.0+ #179
...
NIP mod_timer+0x4c/0x400
LR reset_topology_timer+0x40/0x60
Call Trace:
0xc0000003f9407830 (unreliable)
reset_topology_timer+0x40/0x60
dt_update_callback+0x100/0x120
notifier_call_chain+0x90/0x100
__blocking_notifier_call_chain+0x60/0x90
of_property_notify+0x90/0xd0
of_update_property+0x104/0x150
update_dt_property+0xdc/0x1f0
pseries_devicetree_update+0x2d0/0x510
post_mobility_fixup+0x7c/0xf0
migration_store+0xa4/0xc0
kobj_attr_store+0x30/0x60
sysfs_kf_write+0x64/0xa0
kernfs_fop_write+0x16c/0x240
__vfs_write+0x40/0x200
vfs_write+0xc8/0x240
ksys_write+0x5c/0x100
system_call+0x58/0x6c
Fixes: 5d88aa85c00b ("powerpc/pseries: Update CPU maps when device tree is updated")
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Michael Bringmann <mwb@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Thomas Gleixner [Mon, 24 Sep 2018 08:55:38 +0000 (10:55 +0200)]
Merge branch 'clockevents/4.19-fixes' of https://git.linaro.org/people/daniel.lezcano/linux into timers/urgent
Pull clockevent fixed from Daniel Lezcano:
- Add the CLOCK_SOURCE_SUSPEND_NONSTOP for non-am43 SoCs (Keerthy)
- Fix set_next_event handler for the fttmr010 (Tao Ren)
Friedemann Gerold [Sat, 15 Sep 2018 15:03:39 +0000 (18:03 +0300)]
net: aquantia: memory corruption on jumbo frames
This patch fixes skb_shared area, which will be corrupted
upon reception of 4K jumbo packets.
Originally build_skb usage purpose was to reuse page for skb to eliminate
needs of extra fragments. But that logic does not take into account that
skb_shared_info should be reserved at the end of skb data area.
In case packet data consumes all the page (4K), skb_shinfo location
overflows the page. As a consequence, __build_skb zeroed shinfo data above
the allocated page, corrupting next page.
The issue is rarely seen in real life because jumbo are normally larger
than 4K and that causes another code path to trigger.
But it 100% reproducible with simple scapy packet, like:
sendp(IP(dst="192.168.100.3") / TCP(dport=443) \
/ Raw(RandString(size=(4096-40))), iface="enp1s0")
Fixes: 018423e90bee ("net: ethernet: aquantia: Add ring support code")
Reported-by: Friedemann Gerold <f.gerold@b-c-s.de>
Reported-by: Michael Rauch <michael@rauch.be>
Signed-off-by: Friedemann Gerold <f.gerold@b-c-s.de>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 24 Sep 2018 04:55:26 +0000 (21:55 -0700)]
Merge branch 'netpoll-avoid-capture-effects-for-NAPI-drivers'
Eric Dumazet says:
====================
netpoll: avoid capture effects for NAPI drivers
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC).
This capture, showing one ksoftirqd eating all cycles
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
It seems that all networking drivers that do use NAPI
for their TX completions, should not provide a ndo_poll_controller() :
Most NAPI drivers have netpoll support already handled
in core networking stack, since netpoll_poll_dev()
uses poll_napi(dev) to iterate through registered
NAPI contexts for a device.
This patch series take care of the first round, we will
handle other drivers in future rounds.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:52 +0000 (15:27 -0700)]
tun: remove ndo_poll_controller
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
tun uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:51 +0000 (15:27 -0700)]
nfp: remove ndo_poll_controller
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
nfp uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Tested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:50 +0000 (15:27 -0700)]
bnxt: remove ndo_poll_controller
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
bnxt uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:49 +0000 (15:27 -0700)]
bnx2x: remove ndo_poll_controller
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
bnx2x uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:48 +0000 (15:27 -0700)]
mlx5: remove ndo_poll_controller
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
mlx5 uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:47 +0000 (15:27 -0700)]
mlx4: remove ndo_poll_controller
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
mlx4 uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:46 +0000 (15:27 -0700)]
i40evf: remove ndo_poll_controller
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
i40evf uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:45 +0000 (15:27 -0700)]
ice: remove ndo_poll_controller
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
ice uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:44 +0000 (15:27 -0700)]
igb: remove ndo_poll_controller
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
igb uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:43 +0000 (15:27 -0700)]
ixgb: remove ndo_poll_controller
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
ixgb uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
This also removes a problematic use of disable_irq() in
a context it is forbidden, as explained in commit
af3e0fcf7887 ("8139too: Use disable_irq_nosync() in
rtl8139_poll_controller()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:42 +0000 (15:27 -0700)]
fm10k: remove ndo_poll_controller
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
lasts for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
fm10k uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:41 +0000 (15:27 -0700)]
ixgbevf: remove ndo_poll_controller
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
ixgbevf uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:40 +0000 (15:27 -0700)]
ixgbe: remove ndo_poll_controller
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
ixgbe uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
Reported-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Song Liu <songliubraving@fb.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:39 +0000 (15:27 -0700)]
bonding: use netpoll_poll_dev() helper
We want to allow NAPI drivers to no longer provide
ndo_poll_controller() method, as it has been proven problematic.
team driver must not look at its presence, but instead call
netpoll_poll_dev() which factorize the needed actions.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Sep 2018 22:27:38 +0000 (15:27 -0700)]
netpoll: make ndo_poll_controller() optional
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
It seems that all networking drivers that do use NAPI
for their TX completions, should not provide a ndo_poll_controller().
NAPI drivers have netpoll support already handled
in core networking stack, since netpoll_poll_dev()
uses poll_napi(dev) to iterate through registered
NAPI contexts for a device.
This patch allows netpoll_poll_dev() to process NAPI
contexts even for drivers not providing ndo_poll_controller(),
allowing for following patches in NAPI drivers.
Also we export netpoll_poll_dev() so that it can be called
by bonding/team drivers in following patches.
Reported-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Song Liu <songliubraving@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tao Ren [Wed, 19 Sep 2018 22:13:31 +0000 (15:13 -0700)]
clocksource/drivers/fttmr010: Fix set_next_event handler
Currently, the aspeed MATCH1 register is updated to <current_count -
cycles> in set_next_event handler, with the assumption that COUNT
register value is preserved when the timer is disabled and it continues
decrementing after the timer is enabled. But the assumption is wrong:
RELOAD register is loaded into COUNT register when the aspeed timer is
enabled, which means the next event may be delayed because timer
interrupt won't be generated until <0xFFFFFFFF - current_count +
cycles>.
The problem can be fixed by updating RELOAD register to <cycles>, and
COUNT register will be re-loaded when the timer is enabled and interrupt
is generated when COUNT register overflows.
The test result on Facebook Backpack-CMM BMC hardware (AST2500) shows
the issue is fixed: without the patch, usleep(100) suspends the process
for several milliseconds (and sometimes even over 40 milliseconds);
after applying the fix, usleep(100) takes averagely 240 microseconds to
return under the same workload level.
Signed-off-by: Tao Ren <taoren@fb.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
David S. Miller [Sun, 23 Sep 2018 19:25:15 +0000 (12:25 -0700)]
rds: Fix build regression.
Use DECLARE_* not DEFINE_*
Fixes: 8360ed6745df ("RDS: IB: Use DEFINE_PER_CPU_SHARED_ALIGNED for rds_ib_stats")
Signed-off-by: David S. Miller <davem@davemloft.net>
Greg Kroah-Hartman [Sun, 23 Sep 2018 17:15:18 +0000 (19:15 +0200)]
Linux 4.19-rc5
Greg Kroah-Hartman [Sun, 23 Sep 2018 15:19:27 +0000 (17:19 +0200)]
Merge tag 'mfd-fixes-4.19' of git://git./linux/kernel/git/lee/mfd
Lee writes:
"MFD fixes for v4.19
- Fix Dialog DA9063 regulator constraints issue causing failure in
probe
- Fix OMAP Device Tree compatible strings to match DT"
* tag 'mfd-fixes-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: omap-usb-host: Fix dts probe of children
mfd: da9063: Fix DT probing with constraints
Greg Kroah-Hartman [Sun, 23 Sep 2018 11:32:19 +0000 (13:32 +0200)]
Merge tag 'for-linus-4.19d-rc5-tag' of git://git./linux/kernel/git/xen/tip
Juergen writes:
"xen:
Two small fixes for xen drivers."
* tag 'for-linus-4.19d-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: issue warning message when out of grant maptrack entries
xen/x86/vpmu: Zero struct pt_regs before calling into sample handling code
Greg Kroah-Hartman [Sun, 23 Sep 2018 06:33:28 +0000 (08:33 +0200)]
Merge tag 'for-linus-
20180922' of git://git.kernel.dk/linux-block
Jens writes:
"Just a single fix in this pull request, fixing a regression in
/proc/diskstats caused by the unification of timestamps."
* tag 'for-linus-
20180922' of git://git.kernel.dk/linux-block:
block: use nanosecond resolution for iostat
Greg Kroah-Hartman [Sun, 23 Sep 2018 06:10:12 +0000 (08:10 +0200)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Thomas writes:
"A set of fixes for x86:
- Resolve the kvmclock regression on AMD systems with memory
encryption enabled. The rework of the kvmclock memory allocation
during early boot results in encrypted storage, which is not
shareable with the hypervisor. Create a new section for this data
which is mapped unencrypted and take care that the later
allocations for shared kvmclock memory is unencrypted as well.
- Fix the build regression in the paravirt code introduced by the
recent spectre v2 updates.
- Ensure that the initial static page tables cover the fixmap space
correctly so early console always works. This worked so far by
chance, but recent modifications to the fixmap layout can -
depending on kernel configuration - move the relevant entries to a
different place which is not covered by the initial static page
tables.
- Address the regressions and issues which got introduced with the
recent extensions to the Intel Recource Director Technology code.
- Update maintainer entries to document reality"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Expand static page table for fixmap space
MAINTAINERS: Add X86 MM entry
x86/intel_rdt: Add Reinette as co-maintainer for RDT
MAINTAINERS: Add Borislav to the x86 maintainers
x86/paravirt: Fix some warning messages
x86/intel_rdt: Fix incorrect loop end condition
x86/intel_rdt: Fix exclusive mode handling of MBA resource
x86/intel_rdt: Fix incorrect loop end condition
x86/intel_rdt: Do not allow pseudo-locking of MBA resource
x86/intel_rdt: Fix unchecked MSR access
x86/intel_rdt: Fix invalid mode warning when multiple resources are managed
x86/intel_rdt: Global closid helper to support future fixes
x86/intel_rdt: Fix size reporting of MBA resource
x86/intel_rdt: Fix data type in parsing callbacks
x86/kvm: Use __bss_decrypted attribute in shared variables
x86/mm: Add .bss..decrypted section to hold shared variables
projects / openwrt / staging / blogic.git / log