b43legacy: Fix module init message

This fixes the module init message to tell that the legacy
driver loaded. This makes it less confusing, in case both drivers are loaded.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rndis_wlan: fix broken data copy

Replace broken code that attempted to copy 6 byte array to 64-bit
integer. Due to missing cast to 64-bit integer, left shift operation
were 32-bit and lead to bytes been copied over each other. New code
uses simple memcpy, for greater readability and efficiency.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: compare the current command with response

instead of with itself.

Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: fix sanity check on sequence number in command response

Slightly more useful if we compare it against the sequence number of the
command we have outstanding, rather than comparing the reply with itself.

Doh. Pointed out by Sebastian Siewior

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54: fix eeprom parser length sanity checks

When I called p54_parse_eeprom() on a hand-coded structure
I managed to make a small mistake with wrap->len which caused
a segfault a few lines down when trying to read entry->len.
This patch changes the validation code to avoid such problems.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54: fix EEPROM structure endianness

Since the EEPROM structure is read from hardware, it is
always little endian, annotate that in the struct and
make sure to convert where applicable.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Michael Wu <flamingice@sourmilk.net>
Tested-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb: Add pcibios_enable_device() return value check

This patch has added pcibios_enable_device() return value check.

Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rc80211-pid: fix rate adjustment

Merge rate_control_pid_shift_adjust() to rate_control_pid_adjust_rate()
in order to make the learning algorithm aware of constraints on rates. Also
add some comments and rename variables.

This fixes a bug which prevented 802.11b/g non-AP STAs from working with
802.11b only AP STAs.

This patch was originally destined for 2.6.26, and is being backported
to fix a user reported problem in post-2.6.24 kernels.

Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PPPOL2TP]: Add missing sock_put() in pppol2tp_tunnel_closeall()

Every skb removed from session->reorder_q needs sock_put().

Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Subject: [PPPOL2TP] add missing sock_put() in pppol2tp_recv_dequeue()

Every skb removed from session->reorder_q needs sock_put().

Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[BLUETOOTH]: l2cap info_timer delete fix in hci_conn_del

When the l2cap info_timer is active the info_state will be set to
L2CAP_INFO_FEAT_MASK_REQ_SENT, and it will be unset after the timer is
deleted or timeout triggered.

Here in l2cap_conn_del only call del_timer_sync when the info_state is
set to L2CAP_INFO_FEAT_MASK_REQ_SENT.

Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

[NET]: Fix race in generic address resolution.

neigh_update sends skb from neigh->arp_queue while neigh_timer_handler
has increased skbs refcount and calls solicit with the
skb. neigh_timer_handler should not increase skbs refcount but make a
copy of the skb and do solicit with the copy.

Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

iucv: fix build error on !SMP

Since a5fbb6d1064be885d2a6b82f625186753cf74848
"KVM: fix !SMP build error" smp_call_function isn't a define anymore
that folds into nothing but a define that calls up_smp_call_function
with all parameters. Hence we cannot #ifdef out the unused code
anymore...
This seems to be the preferred method, so do this for s390 as well.

net/iucv/iucv.c: In function 'iucv_cleanup_queue':
net/iucv/iucv.c:657: error: '__iucv_cleanup_queue' undeclared

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Josef 'Jeff' Sipek <jeffpc@josefsipek.net>
Signed-off-by: Ursula Braun <braunu@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[TCP]: Must count fack_count also when skipping

It makes fackets_out to grow too slowly compared with the
real write queue.

This shouldn't cause those BUG_TRAP(packets <= tp->packets_out)
to trigger but how knows how such inconsistent fackets_out
affects here and there around TCP when everything is nowadays
assuming accurate fackets_out. So lets see if this silences
them all.

Reported by Guillaume Chazarain <guichaz@gmail.com>.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>

[TUN]: Fix RTNL-locking in tun/tap driver

Current tun/tap driver sets also net device's hw address when asked to
change character device's hw address. This is a good idea, but it
misses RTLN-locking, resulting following error message in 2.6.25-rc3's
inetdev_event() function:

RTNL: assertion failed at net/ipv4/devinet.c (1050)

Attached patch fixes this problem.

Signed-off-by: Kim B. Heino <Kim.Heino@bluegiga.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[SCTP]: Use proc_create to setup de->proc_fops.

In addition to commit 160f17 ("[SCTP]: Use proc_create() to setup
->proc_fops first") use proc_create in two more places.

Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

[IRDA]: Use proc_create() to setup ->proc_fops first

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[TCP]: BIC web page link is corrected.

Signed-off-by: Sangtae Ha <sha2@ncsu.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>

[X25]: Use proc_create() to setup ->proc_fops first

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[WANROUTER]: Use proc_create() to setup ->proc_fops first

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[8021Q]: Use proc_create() to setup ->proc_fops first

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[IPV4]: Use proc_create() to setup ->proc_fops first

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[IPV6]: Use proc_create() to setup ->proc_fops first

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[SCTP]: Use proc_create() to setup ->proc_fops first

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[PKTGEN]: Use proc_create() to setup ->proc_fops first

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[NEIGHBOUR]: Use proc_create() to setup ->proc_fops first

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[LLC]: Use proc_create() to setup ->proc_fops first

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[IPX]: Use proc_create() to setup ->proc_fops first

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[SUNRPC]: Use proc_create() to setup ->proc_fops first

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'pending' of /linux/kernel/git/vxy/lksctp-dev

[ATM]: Use proc_create() to setup ->proc_fops first

Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[SCTP]: Update AUTH structures to match declarations in draft-16.

The new SCTP socket api (draft 16) updates the AUTH API structures.
We never exported these since we knew they would change.
Update the rest to match the draft.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>

[SCTP]: Incorrect length was used in SCTP_*_AUTH_CHUNKS socket option

The chunks are stored inside a parameter structure in the kernel
and when we copy them to the user, we need to account for
the parameter header.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>

[SCTP]: Clean up naming conventions of sctp protocol/address family registration

I noticed while looking into some odd behavior in sctp, that the variable
name sctp_pf_inet6_specific was used twice to represent two different
pieces of data (its both a structure name and a pointer to that type of
structure), which is confusing to say the least, and potentially dangerous
depending on the variable scope.  This patch cleans that up, and makes the
protocol and address family registration names in SCTP more regular,
increasing readability.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
 ipv6.c     |   12 ++++++------
 protocol.c |   12 ++++++------
 2 files changed, 12 insertions(+), 12 deletions(-)

[APPLETALK]: Use proc_create() to setup ->proc_fops first

As Davem mentioned in his recently patch
(d9595a7b9c777d45a74774f1428c263a0a47f4c0)
that the procfs visibility should occur after
the ->proc_fops are setup.

And also, Alexey provide proc_create() to make
sure that ->proc_fops is setup before gluing PDE
to main tree.

We use proc_create().

Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[BNX2X]: add bnx2x to MAINTAINERS

Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[BNX2X]: update version, remove CVS strings

Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[BNX2X]: Fix Xmit bugs

Several endianity corrections in start_xmit()

Fixed TSO bug where packets were missing the TCP flags.

Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[BNX2X]: Prevent PCI queue overflow

Limit traffic through an internal queue to prevent overflow.

Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[BNX2X]: fix slowpath races and locking

Fixed locking between fastpath and slowpath operations.

Corrected order of traffic disabling to prevent race when going down
under traffic.

- first have the microcode drop all incoming packets
- then do the slowpath stuff
- only then reset the MAC

Got rid of in_reset_task.

Remove_one() and friends would deference a null pointer if init_one
failed.

Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[BNX2X]: fix HW attentions and error handling

Some of the HW attentions, used to indicate an error were not properly
acked.

This will cause the driver to endlessly receive interrupts when such
an error happens.

Had to break the code into smaller chunks because it got too nested.

Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[BNX2X]: fix MSI-X/INT#A errata

Errata A0.158 workaround.

Running in INT#A mode after running with MSI-X fails due to a PCI core
bug.

Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[BNX2X]: correct statistics

Errors were summed improperly, some stats were missing.

Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[BNX2X]: Correct RX filtering and MC configuration

The configuration of RX filtering needed the following corrections:

Drop flags need to be set per Rx queue.

Have to tell the microcode to collect drop stats, and properly wait
for them to complete when going down.

Sometimes we failed to detect proper completion due to a logical error
in the wait loop.

Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[BNX2X]: Correct Link management

Properly protect PHY access between two devices on the same board with
a HW lock.

Use GPIO to clear all previous configurations before changing link
parameters.

Shut down the external PHY in case of fan failure.

Reducing the MDC/MDIO clock to 2.5MHz due to problems with some
devices.

Resolve the flow control response according to autoneg with external
PHY.

Unmasking all PHY interrupts in single write to prevent a race in the
interrupts order.

LASI indication fixes to work with peculiarities of PHYs.

Disable MAC RX to avoid a HW bug when closing the MAC under traffic.

Disable parallel detection on HiGig due to HW limitation.

Updating the shared memory structure to work with the current
bootcode.

Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[BNX2X]: Correct init_one()

Correct PCI-E info printed by init_one()
In one case it failed to free the netdev.

Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[BNX2X]: Spelling fixes

Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[IPCOMP]: Disable BH on output when using shared tfm

Because we use shared tfm objects in order to conserve memory,
(each tfm requires 128K of vmalloc memory), BH needs to be turned
off on output as that can occur in process context.

Previously this was done implicitly by the xfrm output code.
That was lost when it became lockless.  So we need to add the
BH disabling to IPComp directly.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of /linux/kernel/git/linville/wireless-2.6

SSB PCI core driver: use new SPROM data structure

Switch the SSB PCI core driver to the new SPROM data structure now that
the old one has been removed.

Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Don't build bcm43xx if SSB is static and b43 PCI-SSB bridge is enabled.

This may happen e.g. when the ssb is statically enables by the b44 driver,
and the b43 pci-ssb bridge is enbled by the b43/b43legacy drivers, or the
b43/b43legacy drivers are built statically.

Signed-off-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Use a separate config option for the b43 pci to ssb bridge.

The bridge code was unnecessary enabled by the b44
driver, but it prevents the bcm43xx driver from
being loaded, as the bridge claims the same pci ids.

Now we enable the birdge only if the b43{legacy}
drivers are selected.

Signed-off-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

libertas: Remove unused exports

The libertas driver exports a number of symbols with no in-tree users;
remove these unused exports.  lbs_reset_device() is completely unused, with
no callers at all, so remove the function completely.

A couple of these unused exported symbols are static, which causes the
following build error on ia64 with gcc 4.2.3:

    drivers/net/wireless/libertas/main.c:1375: error: __ksymtab_lbs_remove_mesh causes a section type conflict
    drivers/net/wireless/libertas/main.c:1354: error: __ksymtab_lbs_add_mesh causes a section type conflict

Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix kmalloc vs. net_ratelimit

The "goto end;" part definitely must not be rate limited.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix rt2x00lib_reset_link_tuner()

rt2x00lib_reset_link_tuner() can be called from within
the link tuner itself. This means that it should
_not_ call rt2x00lib_stop_link_tuner() since that will
cause the thread to hang.

Reorder the things that should be done during a
link tuner reset and during a link tuner start.

Also make antenna tuning the last step of the link
tuner since it could possibly reset some statistical
information which we need for average calculation.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Don't switch to antenna with low rssi

When rssi_a > rssi_b is true and the current antenna
was already antenna A, then rt2x00 incorrectly jumped
to antenna B.

Also don't configure the antenna when there has been
no change in the antenna setup.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Add link tuner safe RX toggle states

This adds 2 new states which both are used to toggle
the RX. These new states are required for usage
inside the link tuner thread, because the normal
RX toggling will stop the link tuner thread.
While it is possible that the link tuner thread itself
is the caller of the RX toggle (when using software
antenna diversity).

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix antenna diversity

Fix 2 issues in antenna diversity selection.

1) the following statement will always return true.
if ((rssi_curr - rssi_old) > -5 || (rssi_curr - rssi_old) < 5)
It is cleaner to check if the absolute value is smaller then 5.

2) Only enable software diversity when default antenna setup
indicates support for it. Don't select it when the hardware
does not indicate support for it...

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

gelic wireless driver needs WIRELESS_EXT support

|   CC      drivers/net/ps3_gelic_wireless.o
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c: In function 'gelic_wl_setup_netdev_ops':
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c:2660: error: 'struct net_device' has no member named 'wireless_data'
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c:2661: error: 'struct net_device' has no member named 'wireless_handlers'
| make[3]: *** [drivers/net/ps3_gelic_wireless.o] Error 1
| make[2]: *** [drivers/net] Error 2
| make[1]: *** [drivers] Error 2
| make[1]: *** Waiting for unfinished jobs....
| make: *** [sub-make] Error 2

Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Acked-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

PS3: gelic: Link the wireless net_device structure to the corresponding device structure

Link the net_device structure of the wireless part to the
corresponding device structure.

Without this, the sysfs node for this net_device would not have
'device' link.

Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rndis_wlan: fix sparse warnings

It is obviously wrong to use an enum in a little endian struct,
and those other enums should be declared differently.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[SCTP]: Correctly set the length of sctp_assoc_change notification

sctp_assoc_change notification may contain the data from a received
ABORT chunk.  Set the length correctly to account for that.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>

[NETFILTER]: Fix NF_QUEUE_NR() parenthesis

Properly add parens around the macro argument. This is not needed by
the kernel but the macro is exported to userspace, so it shouldn't
make any assumptions.

Also use NF_VERDICT_BITS instead of NF_VERDICT_QBTIS for the left-shift
since thats whats logically correct.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

[NETFILTER]: xt_conntrack: fix IPv4 address comparison

Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

[NETFILTER]: xt_conntrack: fix missing boolean clamping

Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

[NETFILTER]: nf_conntrack: fix smp_processor_id() in preemptible code warning

Since we're using RCU for the conntrack hash now, we need to avoid
getting preempted or interrupted by BHs while changing the stats.

Fixes warning reported by Tilman Schmidt <tilman@imap.cc> when using
preemptible RCU:

[   48.180297] BUG: using smp_processor_id() in preemptible [00000000] code: ntpdate/3562
[   48.180297] caller is __nf_conntrack_find+0x9b/0xeb [nf_conntrack]
[   48.180297] Pid: 3562, comm: ntpdate Not tainted 2.6.25-rc2-mm1-testing #1
[   48.180297]  [<c02015b9>] debug_smp_processor_id+0x99/0xb0
[   48.180297]  [<fac643a7>] __nf_conntrack_find+0x9b/0xeb [nf_conntrack]

Tested-by: Tilman Schmidt <tilman@imap.cc>
Tested-by: Christian Casteyde <casteyde.christian@free.fr> [Bugzilla #10097]
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

[IPV6] SYSCTL: Fix possible memory leakage in error path.

In error path, we do need to free memory just allocated.

Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

[INET]: Don't create tunnels with '%' in name.

Four tunnel drivers (ip_gre, ipip, ip6_tunnel and sit) can receive a
pre-defined name for a device from the userspace.  Since these drivers
call the register_netdevice() (rtnl_lock, is held), which does _not_
generate the device's name, this name may contain a '%' character.

Not sure how bad is this to have a device with a '%' in its name, but
all the other places either use the register_netdev(), which call the
dev_alloc_name(), or explicitly call the dev_alloc_name() before
registering, i.e. do not allow for such names.

This had to be prior to the commit 34cc7b, but I forgot to number the
patches and this one got lost, sorry.

Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

[AF_KEY]: Fix oops by converting to proc_net_*().

To make sure the procfs visibility occurs after the ->proc_fs ops are
setup, use proc_net_fops_create() and proc_net_remove().

This also fixes an OOPS after module unload in that the name string
for remove was wrong, so it wouldn't actually be removed.  That bug
was introduced by commit 61145aa1a12401ac71bcc450a58c773dd6e2bfb9
("[KEY]: Clean up proc files creation a bit.")

Signed-off-by: David S. Miller <davem@davemloft.net>

CONNECTOR: make cn_already_initialized static

It is used in connector.c only, so make it static.

Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

[IPV4]: Reset scope when changing address

This bug did bite at least one user, who did have to resort to rebooting
the system after an "ifconfig eth0 127.0.0.1" typo.

Deleting the address and adding a new is a less intrusive workaround.
But I still beleive this is a bug that should be fixed.  Some way or
another.

Another possibility would be to remove the scope mangling based on
address.  This will always be incomplete (are 127/8 the only address
space with host scope requirements?)

We set the scope to RT_SCOPE_HOST if an IPv4 interface is configured
with a loopback address (127/8).  The scope is never reset, and will
remain set to RT_SCOPE_HOST after changing the address. This patch
resets the scope if the address is changed again, to restore normal
functionality.

Signed-off-by: Bjorn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

[IPV6]: Add missing initializations of the new nl_info.nl_net field

Add some more missing initializations of the new nl_info.nl_net field
in IPv6 stack. This field will be used when network namespaces are
fully supported.

Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

[MACVLAN]: Update Kconfig to refer to iproute

Since the macvlan release I had at least 5 users asking how to configure
it since the old userspace tool doesn't work with the version in the
kernel. Add a pointer to the Kconfig help.

Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

bluetooth: delete timer in l2cap_conn_del()

Delete a possibly armed timer before kfree'ing the connection object.

Solves: http://lkml.org/lkml/2008/2/15/514

Reported-by:Quel Qun <kelk1@comcast.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

tipc: fix integer as NULL pointer sparse warnings in tipc

net/tipc/cluster.c:145:2: warning: Using plain integer as NULL pointer
net/tipc/link.c:3254:36: warning: Using plain integer as NULL pointer
net/tipc/ref.c:151:15: warning: Using plain integer as NULL pointer
net/tipc/zone.c:85:2: warning: Using plain integer as NULL pointer

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'upstream-davem' of /linux/kernel/git/jgarzik/netdev-2.6

Linux 2.6.25-rc3

i2c-i801: Add support for the ICH10

Add the Intel ICH10 SMBus Controller DeviceID's and updates
Tolapai support.

Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

i2c: Make i2c_register_board_info() a NOP when CONFIG_I2C_BOARDINFO=n

Don't require platform code to be #ifdeffed according to whether
I2C is enabled or not ... if it's not enabled, let GCC compile out
all I2C device declarations.  (Issue noted on an NSLU2 build that
didn't configure I2C.)

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

i2c-pca-isa: Add access check to legacy ioports

When probing i2c-pca-isa writes to legacy ioports, which crashes the kernel
if there is no device at that port.
This patch adds a check_legacy_ioport call, so probe fails gracefully
and thus prevents the oops.

Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Alchemy: compile fix

Commit 8b798c4d16b762d15f4055597ff8d87f73b35552 broke
alchemy build, fix it.  Pointed out by Adrian Bunk.

Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

i2c: Storage class should be before const qualifier

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

i2c-pxa: Misc fixes

While working on the PCA9564-platform driver, I sometimes had a glimpse at the
pxa-driver. I found some suspicious places, and this patch contains my
suggestions. Note: They are not tested, due to no hardware.

[JD: Some more fixes.]

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Mike Rapoport <mike@compulab.co.il>
Tested-by: Eric Miao <ymiao3@marvell.com>

ARM: OMAP: Release i2c_adapter after use (Siemens SX1)

Each call to i2c_get_adapter() must be followed by a call to
i2c_put_adapter() to release the grabbed reference. Otherwise the
reference count grows forever and the adapter can never be
unregistered.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Vladimir Ananiev <vovan888@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Merge branch 'upstream-linus' of git://git./linux/kernel/git/jgarzik/libata-dev

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata-core: fix kernel-doc warning
  sata_fsl: fix build with ATA_VERBOSE_DEBUG
  [libata] ahci: AMD SB700/SB800 SATA support 64bit DMA
  libata-pmp: clear hob for pmp register accesses
  libata: automatically use DMADIR if drive/bridge requires it
  power_state: get rid of write-only variable in SATA
  pata_atiixp: Use 255 sector limit

libata-core: fix kernel-doc warning

Fix libata-core kernel-doc warning:
Warning(linux-2.6.25-rc2-git6//drivers/ata/libata-core.c:168): No description found for parameter 'ap'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

sata_fsl: fix build with ATA_VERBOSE_DEBUG

This patch fixes build and few warnings when ATA_VERBOSE_DEBUG
is defined:

  CC      drivers/ata/sata_fsl.o
drivers/ata/sata_fsl.c: In function ‘sata_fsl_fill_sg’:
drivers/ata/sata_fsl.c:338: warning: format ‘%x’ expects type ‘unsigned int’, but argument 3 has type ‘void *’
drivers/ata/sata_fsl.c:338: warning: format ‘%x’ expects type ‘unsigned int’, but argument 4 has type ‘struct prde *’
drivers/ata/sata_fsl.c: In function ‘sata_fsl_qc_issue’:
drivers/ata/sata_fsl.c:459: error: ‘csr_base’ undeclared (first use in this function)
drivers/ata/sata_fsl.c:459: error: (Each undeclared identifier is reported only once
drivers/ata/sata_fsl.c:459: error: for each function it appears in.)
drivers/ata/sata_fsl.c: In function ‘sata_fsl_freeze’:
drivers/ata/sata_fsl.c:525: error: ‘csr_base’ undeclared (first use in this function)
make[2]: *** [drivers/ata/sata_fsl.o] Error 1

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

[libata] ahci: AMD SB700/SB800 SATA support 64bit DMA

SB700 SATA controller can support 64 bit DMA, the previous commit
badc2341579511a247f5993865aa68379e283c5c was added with
careless reference to SB600, which should be modified by this patch.

Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

libata-pmp: clear hob for pmp register accesses

>> Mark Lord wrote:
>>> Tejun, I've added PMP to sata_mv, and am now trying to get it
>>> to work with a Marvell PM attached.
>>>
>>> And the behaviour I see is very bizarre.
>>>
>>> After hard+soft resets, the PM signature is found,
>>> and libata interrogates the PM registers.
>>>
>>> It successfully reads register 0, and then register 1.
>>> But all subsequent registers read out (incorrectly) as zeros.
...

This behavior has been confirmed by Marvell with a SATA analyzer.
The Marvell port-multiplier apparently likes to see clean HOB
information when accessing PMP registers.

Since sata_mv uses PIO shadow register access, this doesn't happen
automatically, as it might in a more purely FIS-based driver (eg. ahci).

One way to fix this is to flag these commands with ATA_TFLAG_LBA48,
forcing libata to write out the HOB fields with known (zero) values.

Signed-off-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

libata: automatically use DMADIR if drive/bridge requires it

Back in 2.6.17-rc2, a libata module parameter was added for atapi_dmadir.

That's nice, but most SATA devices which need it will tell us about it
in their IDENTIFY PACKET response, as bit-15 of word-62 of the
returned data (as per ATA7, ATA8 specifications).

So for those which specify it, we should automatically use the DMADIR bit.
Otherwise, disc writing will fail by default on many SATA-ATAPI drives.

This patch adds ATA_DFLAG_DMADIR and make ata_dev_configure() set it
if atapi_dmadir is set or identify data indicates DMADIR is necessary.
atapi_xlat() is converted to check ATA_DFLAG_DMADIR before setting
DMADIR.

Original patch is from Mark Lord.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

power_state: get rid of write-only variable in SATA

power_state is scheduled for removal, and libata uses it in write-only
mode. Remove it.

Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

pata_atiixp: Use 255 sector limit

AHCI needs sorting too but this deals with the old interface

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

e1000e: remove unused read value in ASPM disable code.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

e1000e: fix spelling errors in comments

Fix some spelling errors and inconsistencies in comment blocks.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

e1000e: fix flow control denial of service possibility

this patch avoids a denial of service from an evildoer sending a
continuous stream of flow control at our adapter that is plugged
into a non-flow control enabled switch.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

e1000e: fix flow control when using ethtool overrides

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

e1000e: fix link up message to show ethX:

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

e1000e: 82573 can use eerd method to read eeprom

This simplifies the 82571/2/3 family initialization a bit
and removes an initialization table no longer needed.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

ixgb: add RNBC counter - no buffer count - to ethtool stats

This counter is valuable to determine if the system is unable
to timely return buffers to the hardware and this counter starts
to increase well before the hardware starts to drop packets. If
users experience rx_no_buffer_count increasing, they should increase
the amount of descriptors. That will provide more buffers for the
hardware and will decrease the chance of hard drops.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

macb: Fix speed setting

Fix NCFGR.SPD setting on 10Mbps.  This bug was introduced by
conversion to generic PHY layer in kernel 2.6.23.

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>